User's Guide
LX Dual Desk Mount Arm
5 - 20 lbs
(2.3 - 9.1 kg)
5 - 20 lbs
(2.3 - 9.1 kg)
5 - 20 lbs
(2.3 - 9.1 kg)
360°
0.5 - 12 lbs
(0.23 - 5.4 kg)
70°
360°
360°
13"
180°
A
1
5°
B
C
2x
D
1x
8x
1x
E
1x
4mm
M4 x 10mm
1x
8x
2
1x
2.5mm
M4 x 10mm
1x
3
ENGLISH
(330 mm)
2x
2x
2x
4x
M3 x 6mm
1x
3x
1x
2x
2x
4
2x
For the latest User Installation Guide please visit: www.ergotron.com
User's Guide - English
Guía del usuario - Español
Manuel de l’utilisateur - Français
Gebruikersgids - Deutsch
Benutzerhandbuch - Nederlands
Guida per l’utente - Italiano
Användarhandbok - svenska
ユーザーガイド : 日本語
用户指南 : 汉语
888-45-175-W-01 rev.F • 12/14
Includes
Constant Force™
Technology
1 /12
Hazard Symbols
Review
These symbols alert users of a safety condition that demands attention. All users should
be able to recognize and understand the
significance of the following Safety Hazards
if encountered on the product or within the
documentation. Children who are not able
to recognize and respond appropriately to
Safety Alerts should not use this product without adult supervision!
Symbol
Signal Word
Level of Hazard
NOTE
A NOTE indicates important information that helps you
make better use of this product.
CAUTION
A CAUTION indicates either potential damage to
hardware or loss of data and tells you how to avoid the
problem.
WARNING
A WARNING indicates either potential for property damage, personal injury, or death.
ELECTRICAL
An Electrical indicates an impending electrical hazard
which, if not avoided, may result in personal injury, fire
and/or death.
Safety
ENGLISH
Important! You will need to adjust this product after installation is complete. Make sure all your
equipment is properly installed on the product before attempting adjustments. This product should
move smoothly and easily through the full range of motion and stay where you set it. If movements
are too easy or difficult or if product does not stay in desired positions, follow the adjustment
instructions to create smooth and easy movements. Depending on your product and the adjustment,
it may take many turns to notice a difference. Any time equipment is added or removed from this
product, resulting in a change in the weight of the mounted load, you should repeat these adjustment
steps to ensure safe and optimum operation.
Warning: Because mounting surface materials can vary widely, it is imperative that you make sure mounting surface is strong
enough to handle mounted product and equipment.
Caution:
To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow
these instructions may result in equipment damage or personal injury.
2 / 12
888-45-175-W-01 rev.F • 12/14
1
Choose Mounting Method
a
4mm
b
c
e
f
d
4mm
< .63" (16 mm)
1.42" - 2.6" (36 - 66 mm)
ENGLISH
.5" - 1.63" (11 - 41 mm)
< 3"
(80 mm)
0.31" - 2"*
(8 - 51 mm)
*Bolt must be
centered in hole.
CAUTION: For secure arm attachment and to avoid equipment damage, plate
must make contact with underside of desk on both sides of the hole.
CAUTION: For Desk Clamp installations: Do Not rotate
display past edge of desk
888-45-175-W-01 rev.F • 12/14
3 /12
2
Attach Display
4x
M4 x 10mm
4x
ENGLISH
M4 x 10mm
0°
WARNING
4 / 12
WARNING! Stored Energy Hazard: The arm mechanism is under tension and will move up rapidly, on its own, as
soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the arm has been
moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or
equipment damage!
888-45-175-W-01 rev.F • 12/14
2
Attach Notebook
a
Attach portrait/landscape rotation stop screw
b
4x
M4 x 10mm
4x
M4 x 10mm
ENGLISH
A
Place Notebook
6
c
B
Place docking station and notebook
7
888-45-175-W-01 rev.F • 12/14
5 /12
A
Place Notebook
2x
Pa ds will help prevent notebook from slipping, but they will not hold all notebooks on the
tray in all circumstances. Use caution while tilting the tray, since some angles may cause the
notebook to fall off resulting in equipment damage or personal injury.
a
b
2x
ENGLISH
c
d
1x
e
1x
1x
f
3
8
6 / 12
888-45-175-W-01 rev.F • 12/14
B
Place docking station and notebook
3x
2x
e
a
b
c
d
3x
f
g
h
i
ENGLISH
j
1x
k
1x
1x
l
3
8
888-45-175-W-01 rev.F • 12/14
7 /12
3
>180º
180º
ENGLISH
WARNING: Desk Clamp Installations: The range of motion (side-toside) for two Extensions/Arms on one pole mounted with the Desk
Clamp option is limited to 180º forward (over front of desk clamp
base). NOTE: Grommet Mount Installations: The range of motion (side-toside) for two Extensions/Arms on one pole mounted with the Grommet
Mount option is 360º
2.5mm
8 / 12
888-45-175-W-01 rev.F • 12/14
4
NOTE: Leave enough slack in cable to allow full range of motion.
Caution: To avoid the potential to pinch cables it is important to follow the cable routing
instructions in this manual. Failure to follow these instructions may result in equipment
damage or personal injury.
ENGLISH
888-45-175-W-01 rev.F • 12/14
9 /12
5
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is
properly installed on the product before attempting adjustments. This product should move smoothly and easily
through the full range of motion and stay where you set it. If movements are too easy or difficult or if product
does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment
is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat
these adjustment steps to ensure safe and optimum operation.
a
Lift – Up and down
4mm
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
ENGLISH
Decrease Lift Strength
4mm
b
CAUTION: DO NOT overtighten fasteners.
Overtightening may cause damage to your
equipment.
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
Tilt – Forward and Backward
4mm
Increase Friction
If this product moves too easily, then
you'll need to increase friction:
CAUTION: DO NOT remove screw. Removing
screw may cause damage to equipment.
Decrease Friction
If this product is too difficult to move,
then you'll need to decrease friction:
4mm
10 / 12
888-45-175-W-01 rev.F • 12/14
c
Tilt – Forward and Backward
2.5mm
Increase Friction
CAUTION: DO NOT remove screw. Removing
screw may cause damage to equipment.
If this product moves too easily, then
you'll need to increase friction:
Decrease Friction
d
ENGLISH
If this product is too difficult to move,
then you'll need to decrease friction:
Rotate – Portrait/Landscape
360°
0°
M3 x 6mm
888-45-175-W-01 rev.F • 12/14
11 /12
6
Set Your Workstation to Work For YOU!
Learn more about ergonomic computer use at:
www.computingcomfort.org
Height Position top of screen slightly below eye level.
Position keyboard at about elbow height with wrists flat.
Distance Position screen an arm's length from face—at least 20” (508mm).
Position keyboard close enough to create a 90˚ angle in elbow.
Angle Tilt screen to eliminate glare.
Tilt the keyboard back 10° so that your wrists remain flat.
To Reduce Fatigue
Breathe - Breathe deeply through your nose.
Blink - Blink often to avoid dry eyes.
Break • 2 to 3 minutes every 20 minutes
• 15 to 20 minutes every 2 hours.
ENGLISH
For local customer care phone numbers visit: http://contact.ergotron.com
NOTE: When contacting customer
service, reference the serial number.
12 / 12
888-45-175-W-01 rev.F • 12/14