Safety Instructions
Safety Instructions
This product has been manufactured to satisfy the international safety standards.
Please read all of safety and operating instructions before operating the product and keep this
manual for future reference.
MAINS SUPPLY
AC 90-250V~, 50/60Hz
Operate your product only from the type of power supply indicated on the marking label. If you
are not sure of the type of power supplied to your home, consult your local power company.
Disconnect the STB from the mains before you start any maintenance or installation procedures.
OVERLOADING
Do not overload a wall outlet, extension cord or adapter as this may result in electric fire or
shock.
LIQUIDS
The product should not be exposed to any liquids such as dripping or splashing. No objects
filled with liquids, such as vases, should be placed on the apparatus,
CLEANING
Before cleaning, disconnect the product from the wall outlet, Use a cloth lightly dampened with
water (no solvents) to clean the exterior.
VENTILATION
The slots on top of the product must be left uncovered to allow proper airflow to the unit. Do not
stand the product on soft furnishings or carpets. Do not expose the product to direct sunlight,
place it near a heater. Do not stack electronic equipment on top of the product.
ATTACHMENTS
Do not use any attachment that is recommended by the manufacturer it may cause a hazard or
damage the product.
CONNECTION TO THE SATELLITE DISH LNB
Disconnect the product from the mains before connecting or disconnecting the cable from the
satellite dish. Failure to do so can damage the LNB.
CONNECTION TO THE TV
Disconnect the product from the mains before connecting or disconnecting the cable from the
satellite dish. Failure to do so can damage the TV.
LOCATION
Place the product indoors in order not to expose to lightning, rain or sunlight.
Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifier) that product heat.
LIGHTNING, or NOT IN USE
Unplug the product from the wall outlet and disconnect the cable during a lightning storm or
when unused for a long time.
SERVICING
Do not attempt service that this product yourself, as opening or removing covers may expose
you to dangerous voltage or other hazard. Refer all servicing to qualified service personnel.
“The mains plug is used as the disconnect device. Then disconnect device shall remain
readily operable”
2 English
Contents
Contents
Safety instructions................................. 2
Chapter 5
Chapter 1
Menu Map................................................ 15
Main Menu............................................... 16
Installation............................................. 16
Before You Begin.................................... 4
General Features.................................. 4
Accessories........................................... 4
Chapter 2
Controls and Functions......................... Front Panel........................................... Rear Panel............................................ Remote Control Unit............................. 5
5
5
6
Chapter 3
Connections............................................ 8
Location of your receiver......................... Connecting your receiver with
dish system............................................. Connecting your analog receiver............ Connecting your receiver to TV............... Connecting your receiver to VCR
(depending on model)............................. Connecting external audio/Hi-Fi system.... Connecting digital audio system............. 8
8
9
9
9
9
9
Chapter 4
Auto Scanning......................................... 16
Manual Scanning.................................... 16
Defaults Setting....................................... 17
System Setup........................................ 17
Language Setting.................................... OSD Setting............................................ Media Settings........................................ Time Setting............................................ Reservation Setting................................. System Information................................. 17
18
18
19
19
19
Delete Channels..................................... Delete All Channels................................. Favorite Channels................................... Edit Channels.......................................... SW Manager........................................... 20
20
21
21
22
Channel Setup...................................... 20
Parental Lock........................................ 22
Channel Lock.......................................... 22
Lock Control............................................ 23
Change Pin Code.................................... 23
Game.................................................... Multimedia............................................. Conditional Access................................ Troubleshooting..................................... Specifications......................................... 23
24
25
26
27
Initial Settings and Operations.............. 10
Menu Information.................................. 10
Getting Started...................................... 10
Selecting the On Screen Display (OSD)
Language................................................ 10
Basic Operation.................................... 11
Switching Channel.................................. Volume Control....................................... Info Bar................................................... Selecting the soundtrack......................... Selecting the OSD teletext, VBI teletext,
Subtitle and DVB subtitle........................ MoSAic . ................................................. Sleep Timer Function.............................. Zoom Function........................................ Channel List............................................ To view channel list in specific order
(Alphabet/Satellite/Provider/HD)............. Electronic Program Guide (EPG)............ 11
11
12
12
12
13
13
13
13
14
14
English 3
Chapter 1 >> Before You Begin
Before You Begin
General Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Accurate, Brilliant Friendly OSD with Full Function
MPEG-2 (MP@ML), MPEG-2 (MP@HL), MPEG4 AVC/H.264, HP@L4
2 SCARTS for TV, VCR (optional)
16 Bit Colors Graphic User Interface
Multi-language Menu
13-digit VFD (Time clock in Stand-by mode)
OSD Teletext Supported
EPG (Electronic Program Guide) for On-screen Channel Information
Installation by Easy Setup Guide
10,000 Channels
User-friendly Data Editing Function
Favorite Channel and Parental Lock Function
RS232C Port for Additional Information Service and Upgrading System Software
S/PDIF OUT Optical and Coaxial
HDMI
SVIDEO OUT
PVR Ready
Time-Shift
Unicable
Ethernet PortOptional)
USB Port
2 Common Interface and 2 Smart card Reader
Blind scanning function
Accessories
•
•
•
•
User’s Manual
Remote Control Unit
Batteries
HDMI Cable (Optional)
4 English
Chapter 2 >> Controls and Functions
Controls and Functions
Front Panel
1
Power ( ) button
Turns your receiver On/Off.
2
Arrow (◄/►) buttons
Adjusts the volume and moves the cursor
left/right on the menu
3
Arrow (▲/▼) buttons
Changes channels or moves the cursor
up/down on the menu.
4
MENU button
Displays the menu
Exits from the current menu or goes to the
previous menu
5
OK button
Confirms selection
6
DISPLAY
Displays channel information
Displays local time in Standby mode
Rear Panel
1
6
4
2
2
3
4
5
6
11
5
8
13
14
9
3
1
7
10 12
RF IN
It Connects to the Cable antenna for DTV
signal.
LOOP
Loop out is an output port of the DISH
INPUT signal.
USB
Connects to the External HDD or USB
storage with USB cable.
RS-232C
Connect to a PC.
RS232 transfers data to the external
computer.
e-SATA
Connects to the External HDD with SATA
cable.
VIDEO OUT
Connects to video input jack on TV or any
external Video system.
AUDIO OUT, LEFT / RIGHT
Connects to audio input jacks on TV or any
external audio system.
8 Y Pb Pr OUT
Connects to video input jack on TV or any
external Video system.
9 S-Video OUT
Connects to the TV with S-Video cable
10 S/PDIF OUT Optical & Coaxial
Connects to a digital audio component with
optical cable.
11 Ethernet(Optional)
Connects to the Ethernet with Ethernet cable
12 HDMI
Connects to the TV with HDMI cable
13 SCART for VCR
Connects to the VCR(AUX) with SCART
cables.
14 SCART for TV
Connects to the TV with SCART cables.
7
English 5
Chapter 2 >> Controls and Functions
Remote Control Unit
1
2
3
4
5
6
7
8
9
Power ( ) button for TV & STB
Turns your receiver & TV On/Off.
Numeric (0~9) buttons
Controls the number entry and changes
program channel directly.
Mode (
) button
Switches between TV and Radio channel list.
Sleep ( ) button
Shows the time setting for the sleep-timer.
MoSAic ( ) button
Displays multi picture section.
Arrow (◄/►) or OK buttons
Adjusts the volume level or moves the
cursor left or right on the menu.
Arrow (▲/▼) or OK buttons
Changes channels or moves the cursor up
or down on the menu.
Menu ( ) button
Displays the menu
Exits from the current menu or goes to the
previous menu.
Mute ( ) button
Mutes audio output.
Last button
Shows Viewed Channel List.
( ) button
Shows the Input Audio information.
11 OK button
Shows Channel list while watching TV or
listening to the Radio.
12 Guide (
) button
Shows the TV program guide.
13 VOL +/- buttons
Adjusts the volume level.
14 Zoom ( ) button
Zooms in the selected screen.
The Zooming location changes by pressing
direction buttons. (x2 → normal)
10 Audio
6 English
( ) button
Changes to the teletext mode.
16 INFO ( ) button
Displays program information in the
screen.
17 Back ( ) button
Goes to previous menu. The changed
values are to be saved.
18 SAT ( ) button
Shows satellite channel list.
15 Text
+/- buttons
Changes channel up or down.
19 PR
(+/-) buttons
Moves up or down pages on the menu and
TV/Radio List.
21 FAV (♥) button
Go to the last channel you’ve watched in
the Favorite Channel List 1.
And if pressed angina, you can see the last
channel you’ve watched in the next Favorite
Channel List2. Repeat pressing the button
until no more Favorite Channel is found.
Then it returns to the current channel.
22 REW button
Rewinds the recorded programs to x8.
23 Play button
Play the recorder programs
Shows the recorded program in the media
player.
24 FWD button
Fast forward the recorded program to x16.
25 Record button
Starts to record programs.
26 Stop button
Stops to record the program and to play
the program.
20 Page
27 Pause
button
Pauses and play the program.
28 F1
button
Set the Video format.
Chapter 2 >> Controls and Functions
29 F2
button
Shows Media Player.
30 F3
button
Starts Time shift function.
31 Additional
function
1. Learning Method
• If there is no further action within 30
seconds in LEARN MODE, the remote
control turns to normal operation mode
switching LED off.
• TV Power key doesn’t have Default key
data.
The Learning Method
• Only the key of “TV Power”has Learning
function.
• Toggle Learning (Continuous 2 codes
should be learned in TV Power key)
• 1st Learned data is produced upon 1st
press and then 2nd Learned data will be
produced upon next pressing on the TV
Power key.
 If you press [TV Power + OK] KEYs
at the same time for 1.5 seconds, the
remote goes into leaning mode. => Then
LED ON will be “ON’ for 30 seconds.
If there is no further action, it will
automatically turn back to normal mode
after 30 seconds switching LED off.
 Press TV Power key one more time. LED
blinks one time and then LED will be “ON”.
 Press 1st SOURCE KEY (Power key of
the original key)
 If it learns correctly, --- LED will be
“ON”after blinking Two Times.
- If it does not learn correctly, --- LED
will be “ON” after blinking 5 Times
- If there is no input Signal for 30
seconds, the remote will stay in
learning mode after blinking 5 times.
- If no further input signal for another
30 seconds, the remote will return to
normal operation mode. LED will be
OFF.
- If you want to teach it again, then you
need to press TV Power key. --- LED
will stay “ON”after blinking one time.
 Now you learned one code from your
original TV power key. Please press TV
Power key one more time. --- LED will
stay ON after blinking one time.
=> If the first TV Power code is learned
correctly (after LED Blinking two times),
2nd code can be taught.
 Please press 2nd SOURCE KEY(Any
numeric key from the original remote
control. For example Number 1)
 If it learns correctly, --- LED will be “ON”
after blinking Two Times.
If it does not learn correctly, --- LED will
be “ON” after blinking 5 Times
=> If there is no input Signal for 30
seconds, the remote will stay in learning
mode after blinking 5 times.
If no further input signal for another 30
seconds, the remote will return to normal
operation mode. LED will be OFF.
=> If you want to teach it again, then you
need to press TV Power key. --- LED will
stay “ON” after blinking one time.
 If you press [TV Power + OK] Keys at
the same time, it turns back to normal
operation mode after LED blinking 3
times.
2. Low Battery Warning Function
It is the fuction to check if the battery has
LOW VOLTAGE
 If you press [STB Power] KEY at the
level that IC’s OPERATING VOLTAGE is
as low as “2.2V ~ 2.3V”, power code will
be produced blinking LED 3 times.
 At that LOW VOLTAGE level, you can
not go into LEARNING MODE.
English 7
Chapter 3 >> Connections
Connections
Loop through
Location of your receiver
• Install your receiver in horizontal position
• Do not put any heavy stuff such as a TV on your receiver
• Do not install your receiver in the places as follows: Vibrating place, direct sunrays, Humid
place, too high or low temperature, and no ventilated place.
Connecting your receiver with dish system
After installing your antenna system, connect the coaxial cable from the LNB of your antenna to
“DISH INPUT” terminal marked at the rear panel of your receiver. All cable connectors should
be finger-tightened; do not use any kind of wrench while tightening connectors. The cable
should be 75 ohm impedance coaxial twisted at the end with an “F” type connector.
8 English
Chapter 3 >> Connections
Connecting your analog receiver
To facilitate the user using analog receiver to view analog channels, this product has been
provided with a loop through terminal marked as “Loop”. Connect the coaxial cable from this
terminal to the IF input terminal of your analog receiver. Now by keeping your receiver in
standby, you will be able to tune and view analog channels from your analog receiver.
Connecting your receiver to TV
To connect your receiver with your television, you can use 4 different methods; via RCA cable,
SCART cable, HDMI cable or YUV.
Connect the RF cable to the terminal marked “RF OUT” on the rear panel of your receiver and
its other end to the TV RF input socket.
Connect the Video/Audio RCA cables from the Video OUT/AUDIO OUT (LEFT, RIGHT) on the
rear of your receiver to the Video INPUT/AUDIO INPUT (LEFT, RIGHT) jacks on the TV. In the
case of connecting your TV through SCART cable, connect the SCART connector marked TV to
the respective SCART port on the TV. (depend on model)
Connect the HDMI cable to the terminal marked “HDMI” on the rear panel of your receiver
and its other end to the TV HDMI input.
Connecting your receiver to VCR (depending on model)
To connect a VCR, your receiver has been provided with SCART at the rear marked “VCR”.
Using a SCART connector, the VCR can be connected to your receiver.
Connecting external audio/Hi-Fi system
To connect any external Audio Hi-Fi system, your receiver has been provided with two RCA
connectors at the rear panel of your receiver, marked with AUDIO L and R respectively to
connect the left and right Audio on the external audio/Hi-Fi system.
Connecting digital audio system
Connect a cable between S/PDIF OUT at the rear panel of your receiver and S/PDIF INPUT
COAXIAL or OPTICAL on the Digital Audio System.
English 9
Chapter 4 >> Initial Settings and Operations
Initial Settings and Operations
Menu Information
A menu is a field of text shown on the TV screen. Selectable lines are generally activated
(highlighted). No-activated lines cannot be selected. Most of menus show short information at
the bottom of the screen.
This menu consists of 7 main menus:
• Installation
• Game
• System Setup
• Multimedia
• Channel Setup
• Conditional Access
• Parental Lock
1 Using the Arrow (▲/▼) buttons you can move upwards and downwards on the menus.
On the menus, you can search channels using this button.
2 When you have reached the required subject menu, press the OK button to confirm your
choice.
3 On the menus, you can select menu items using the Arrow (◄/►) buttons.
4 When you want to return to the previous menu with saving the change, press the Back ( )
button.
5 When you want to exit from the current menu, press the Menu (
) button.
Getting Started
To start your receiver for the first time, you must select the language for displaying menus
and you should set parameters for system configuration and scan satellite channels. Perform
the following setup procedure for scanning the satellite. Follow the instructions below to scan
satellite channels. You can enjoy watching TV or listening to the Radio after the procedure
completes.
1 Turn on your TV and receiver.
Language Setting menu will appear automatically.
OSD Language is highlighted.
Selecting the On Screen Display (OSD)
Language
2 Select the OSD language of your choice using the Arrow
(◄/►) buttons.
You will see the selected language on the OSD menu.
3 Select Installation using the Arrow (◄/►) buttons.
10 English
Chapter 4 >> Initial Settings and Operations
Basic Operation
This section explains various functions while watching TV or listening to the Radio.
Switching Channel
You can switch the current channel by three different methods.
• Method 1: Press the Arrow (▲/▼) buttons or PR+/- buttons.
• Method 2: To select a channel directly, select a channel using the Numeric (0~9) button.
• Method 3:
1 To display the channel list, press the OK button.
2 Select a channel you want to watch using the Arrow (▲/▼) buttons and then press the OK
button.
• If there are multiple channels, use the Page (+/-) or the Arrow (◄/►) buttons to move to
channels by page.
) button to switch between the TV and Radio channel.
• Press the Mode (
• Method 4: In case of more than two scanned satellites
1 Press the SAT( ) button to show satellite list.
2 Move the cursor to the satellite of a channel to watch with the Arrow (◄/►) buttons and
then press OK button.
3 You can follow the method 3 instruction for channel selection.
• Method 5: How to move to the watched channel.
1 Press the last button with RCU.
2 Press OK button after a channel selection by using the Arrow (▲/▼) with RCU.
3 Press OK button to exit.
Volume Control
To control the volume:
• Press the VOL+/- or the Arrow (◄/►) buttons.
• Press the Mute ( ) button to turn the sound off.
• Press the Mute ( ) button again or the VOL+/- or Arrow (◄/►) buttons to cancel muting.
English 11
Chapter 4 >> Initial Settings and Operations
Info Bar
Channel information always appears for a specific period of time whenever you switch
channels.
General Information
Press the INFO ( ) button; you can see general information of the current channel.
1 Channel number and name
2 Current time
3 Signal Level
4 Signal Quality
5 Icons: HD channel, Locked channel, Radio Channel, Scrambled channel, Subtitle, Teletext
information
6 EPG information.
7 Conditional Access
Detailed Channel Information
You can see detailed channel information pressing the INFO ( ) button again.
8 You can see detailed channel information pressing the INFO button again.
9 Satellite, Frequency, Symbol Rate, FEC, Polarity, Video PED, Audio PID, PCR PID,
Transponder
10 Display the stream information.
Selecting the soundtrack
You can select the audio language, soundtrack, or sound mode.
1 Press the Audio (Yellow) button.
2 Press the Arrow (▲/▼) buttons to select the audio language
or soundtrack and press the OK button.
3 Press the Arrow (◄/►) buttons to select the sound mode
from Stereo, Mono left, or Mono Right.
4 Stream information.
Selecting the OSD teletext, VBI teletext, Subtitle and DVB subtitle
You can choose the OSD teletext, VBI teletext, subtitle and DVB subtitle for the current live
TV program if provided from the broadcasting station.
• OSD teletext: Press the Text ( ) button
• VBI teletext: Press the Text ( ) button twice.
• Subtitle: Press the Text ( ) button three times.
• DVB subtitle: Press the Text ( ) button four times.
12 English
Chapter 4 >> Initial Settings and Operations
MoSAic
You can see multi picture by pressing the RED (MoSAic) button.
Sleep Timer Function
Press the GREEN (Sleep) button, you will see the time set for the sleep timer if already set from
the Time Setting menu.
Zoom Function
You can make the picture appear larger on the screen pressing the Zoom ( ) button.
1 Press the Zoom ( ) button.
2 Select the area you want to zoom using the Arrow buttons
and then press the OK button.
Picture is enlarged two times.
3 Each time you press the Page (+/-) buttons, the picture is
enlarged two or four times.
Press the Arrow (▲/▼/◄/►) buttons to change the
location at the lower right of display.
4 To cancel the Zoom function, press the Zoom ( ) button
twice or Back ( ) button.
Channel List
You can see the TV or Radio channel list pressing the OK button while watching TV or listening
) button. The icon (€) behind
to the Radio. Switch the channel list pressing the Mode (
the channel name symbolizes scrambled channel, and the ( ) icon behind the channel name
symbolizes indicates a locked channel.
Select channel using the Arrow (▲/▼/◄/►), PR+/-, or Page
(+/-) buttons and press the OK button to watch.
The colored buttons show the channel lists as follows:
• RED (MoSAic) button: by alphabetical order
(alphabetical A-Z)
• GREEN (Sleep) button: by frequency
(all/searched satellites)
• YELLOW (Audio) button: by names of broadcasting
providers
• Blue (SAT) button: by HD channels
English 13
Chapter 4 >> Initial Settings and Operations
To view channel list in specific order
(Alphabet/Satellite/Provider/HD)
1 Press the Colored (Red/ Green/Yellow/Blue) button.
Channel list is highlighted.
2 Select Alphabet, Frequency, Provider, or HD using the
Arrow (▲/▼) buttons.
The channel list is sorted automatically by your selection.
3 Select the channel pressing the Arrow (▲/▼) or Page
( / ) buttons and press the OK button to watch it.
Electronic Program Guide (EPG)
EPG displays program information such as program titles, broadcasting schedule,
Program synopsis and such EPG service differ depending on the service provider.
1 Press the EPG ( ) button while watching TV or listening
to the Radio EPG information appears.
2 Select a program for further more information.
• Arrow (▲/▼) buttons: Selects a program by channel
• Arrow (◄/►) buttons: Selects a program by time &
date within the same channel.
It displays the program list at 30 minutes intervals.
• You can see the detailed information by pressing Page
(+/-) buttons with RCU.
3 Press the OK button, detailed information on the selected
event appears.
4 To exit from the EPG mode, press the Back ( ) button.
14 English
Chapter 5 >> Main Menu
Menu Map
Installation
Auto Scanning
Manual Scanning
Blind Scanning
Defaults Setting
System Setup
Language Setting
OSD Language / Audio 1st Language / Audio 2nd
Language /EPG 1st Language / EPG 2nd Language /
Teletext Language / Subtitle Language
OSD Setting
Transparency / Window Trans / Banner Time / Screen
Saver Time/Serial Module
Media Setting
TV system / TV Aspect Ratio / Video Aspect Ratio / Video
Signal Type / Video Freeze / Dolby Digital/ Time shift
Time Setting
GMT Time / Local Time / Set Time Mode / Time Zone/
Summer Time
Reservation Setting
On Time / Off Time / Repetition / Program
System Information
Channel Setup
Delete Channels
Delete All Channels
Favorite Channels
Edit Channels
SW Manager
Parental Lock
Channel Lock
Lock Control
Change PIN Code
Game
A
B
C
D
Multimedia
USB
SATA
Ethernet
Conditional Access
CI Slot A
CI Slot B
CA Slot A
CA Slot B
English 15
Chapter 5 >> Main Menu
Main Menu
The menu has been carefully designed from user-friendly point of view to assure easy operation
to your receiver. The main menu is classified into 7 sub menus that will carry out the various
operations individually.
Installation
In the Installation menu, you can customize antenna setting and do channel scanning.
Press the Menu ( ) button.
Select Installation using the Arrow (◄/►) buttons on the main menu.
Installation >> Auto Scanning
Auto Scanning
If you select the satellite to scan channel according to the
antenna setting, your receiver can automatically scan the
satellite without entering any other information.
1 Select Auto Scanning using the Arrow (▲/▼) buttons on
the Installation menu and press the OK button.
2 Press the OK button, and then it starts scanning.
After Auto Scanning completes, you can see TV and Radio
channels in the list.
Installation >> Manual Scanning
Manual Scanning
You can scan channels of the selected satellites by transponders if you know the transponder
information.
1 Select Manual Scanning using the Arrow (▲/▼) buttons
on the Installation menu and press the OK button.
2 Set the following options to complete Manual Scanning.
 Transponder
Set the transponder for the selected satellite.
Select a transponder using the Arrow (◄/►) buttons.
 Frequency/Symbol Rate
In put the desired value by pressing numeric (0~9)
buttons.
 Modulation
Select a modulation type using the Arrow (◄/►) buttons.
3 Press the OK button, then starts scanning.
After Auto Scanning is complete, you can see TV and Radio channels found from Auto Scanning.
16 English
Chapter 5 >> Main Menu
Installation >> Blind Scanning
Blind Scanning
When you don’t have any transponder information, you can use this function to have all
channels from selected cable.
1 Go for menu and select “blind scanning” using the Arrow (▲/▼) buttons and press OK
button.
2 Select an appropriate cable using the Arrow (▲/▼), then press OK button to start the blind
scan procedure and the following screen will be displayed.
Please note that the scan procedure may take a few minutes.
3 Press the “menu” key or “exit” key to return to previous menu.
Installation >> Defaults Setting
Defaults Setting
You can restore the default setting in case you have encountered some problems after saving
changes to channel data and others that may be in error.
1 Select Defaults Setting using the Arrow (▲/▼) buttons on the Installation menu and press
the OK button.
2 Select a defaults option (Factory Defaults, or STB Reboot) using the Arrow (▲/▼) buttons
and press the OK button.
• Factory Defaults: Resets back to the factory-default settings.
If you press the OK button in this menu, you will see a dialog box asking you to confirm
the channel defaults or factory defaults setting.
Select Yes or No, and press the OK button.
• STB Reboot
If you press the OK button in this menu, the Set-top box (STB) reboots.
System Setup
You can set the system configuration in this menu. Press the Menu (
Select System Setup using the Arrow (◄/►) buttons on the
menu.
) button.
System Setup >> Language Setting
Language Setting
You can set languages for OSD, Audio 1-2, Teletext, Subtitle,
and EPG 1-2
1 Select Language Setting using the Arrow (▲/▼) buttons
on the System Setup menu and press the OK button.
2 Select any of OSD, Audio1- 2, Teletext, Subtitle, and
EPG1-2 languages using the Arrow (▲/▼) buttons and
use the Arrow (◄/►) buttons to select its language.
English 17
Chapter 5 >> Main Menu
System Setup >> OSD Setting
OSD Setting
You can adjust OSD Transparency, Window Trans OSD Banner Time, and Screen Saver Time.
1 Select OSD Setting using the Arrow (▲/▼) buttons on
the System Setup menu and press the OK button.
2 Select any of Transparency, Window Trans, Screen
saver Time, VFD Module and Display in Standby Mode,
and Screen saver Time using the Arrow (▲/▼) buttons
and use the Arrow (◄/►) buttons to make changes.
• Transparency: 0 (opaque) to 100%
• Window Trans: 0 (opaque) to 100%
• Banner Time: 1 to 60 seconds or Always
• Screen saver Time: 1 to 60 minutes or None
• Serial Module: X-crypt or None
System Setup >> Media Setting
Media Setting
You can enter the various media setting for TV System, TV Aspect Ratio, Video Aspect Ratio,
RGB, Y/Pb/Pr or Composite, RF Channel, Broadcasting System, Video Freeze and DVB
Subtitle.
1 Select Media Setting using the Arrow (▲/▼) buttons on
the System Setup menu and press the OK button.
2 Select Media Setting using the Arrow (▲/▼) buttons and
press the Arrow (◄/►) buttons to make changes.
• TV System: 576p, 720p, 1080i
• TV Aspect Ratio: You can set the aspect ratio of your
TV. (4:3,16:9 or Auto)
• Video Aspect Ratio: You can select the display format
according to TV screen ratio.
(Letter Box, Pan & Scan, Mixed, or Full)
• Video Signal Type: RGB, Y/Pb/Pr, Composite
• Video Freeze: On/Off
• Dolby digital: PCM/Bitstream
• Time Shift: Manual / Auto
18 English
Chapter 5 >> Main Menu
System Setup >> Time Setting
Time Setting
You can set the time zone.
1 Select Time Setting using the Arrow (▲/▼) buttons on the
System Setup menu and press the OK button.
 Set Time Zone:
Press the Arrow (◄/►) buttons to set time mode for Auto
or Manual
 Time Zone
Press the Arrow (◄/►) buttons to set the time zone.
The local time will be automatically changed by this setting.
Set the time by using the Arrow (◄/►) buttons in case of
Auto set time mode
Input the figures with the numeric keys in case of Manual
set time mode
 Summer Time: Select the summer time function on or off
System Setup >> Reservation Setting
Reservation Setting
You can set timer of reservation for TV program such as switch
on, off and TV program. Select the Event NO. for the reservation.
• ON time: Input the Switch-ON time with numeric keys.
• OFF time: Input the Switch-OFF time with numeric keys.
• Repetition: Select the Event activation time option
(Once, Daily, one day a week) with the Arrow (◄/►)
buttons.
• Program: Select the channel with Arrow (◄/►) button
and press OK to save.
System Setup >> System information
System Information
You can check system information like Model Name, hardware version, Loader version, Main
Software version, and Main Software Build Date.
English 19
Chapter 5 >> Main Menu
Channel Setup
You can edit TV and Radio channels and the favorite channel group in this menu.
Press the Menu ( ) button. Select Channel Setup using the Arrow (◄/►) buttons on the
main menu.
Channel Setup >> Delete Channels
Delete Channels
You can delete TV and Radio channels you want.
1 Select Delete Channel using the Arrow (▲/▼) buttons on
the Channel Setup menu and press the OK button.
2 Select the channel you want to delete using the Arrow
(▲/▼) buttons and press the OK button.
Press the Arrow (◄/►) buttons to switch between TV and
Radio List.
You can select multiple channels.
Bulleted list indicates selected channels.
Press the Green (sleep) button for Delete mode by
Channel, TP or Satellite.
3 Press the RED (MoSAiC) button to delete selected
channels.
Channel Setup >> Delete All Channels
Delete All Channels
You can delete all channels.
1 Select Delete All Channels using the Arrow (▲/▼)
buttons on the Channel Setup menu and press the OK
button. System message dialog box appears asking you to
confirm it.
2 Select Yes using the Arrow (◄/►) buttons and press the
OK button to delete all channels.
20 English
Chapter 5 >> Main Menu
Channel Setup >> Favorite Channels
Favorite Channels
You can edit favorite channels. There are 9 favorite channel groups (News, Sports, Movie,
Music, Shopping, Kids, Adults, Drama, and Education).
1 Select Favorite Channels using the Arrow (▲/▼)
buttons on the Channel setup menu and press the OK
button.
2 Select channels that you want to edit using the Arrow
(▲/▼) or Page (+/-) buttons in the TV/Radio List and
press the RED (MoSAic) button.
Selected channels are listed in the favorite group.
) button switches between
Pressing the TV/Radio (
TV and Radio List.
3 Press the FAV (♥) button to select another favorite group.
4 Select channels that you want to edit using the Arrow
(▲/▼) buttons in the TV/Radio List and press the RED
(MoSAic) button. Repeat steps from 3 to 4.
5 Press the OK button to confirm.
Channel Setup >>Edit Channels
Edit Channels
You can rename the channel list.
Select Edit Channels using the Arrow (▲/▼) buttons on the Channel Setup menu and press
the OK button.
• FAV (♥) button: Shows Favorite channel lists
• Arrow (◄/►) buttons: Switches between TV and Radio channel lists
To rename the channel list
1 Select the channel you want to rename using the Arrow
(▲/▼), PR+/-, or Page (+/-) buttons and press the
GREEN (Sleep) button. Font Table will appear.
2 Press the BLUE (SAT) button to delete the selected
channel name.
3 Select characters using the Arrow buttons and press the
RED (MoSAic) button to enter characters.
• YELLOW (Audio) button: Enters space
• BLUE (SAT) button: Hits the back space
• RED (MoSAic) button: Selects the input
4 Press the OK button to confirm.
English 21
Chapter 5 >> Main Menu
Channel Setup >> SW Manager
SW Manager
You can download the software of your receiver through
satellite when the new software is available for your system.
During download, don’t turn off your receiver. In case of the
power is turned off, turned on your receiver again to complete
the download.
1 Select Software manager using the Arrow (▲/▼) buttons
on the Installation menu and press the OK button.
• Program Upload: Copies all the data from Master STB
to Slave STB.
• Channel Data Upload: Copies only the channel data
from master STB to Slave STB.
Connects both Master and Slave STB using RS232C
Cable and then press the OK button on the Software
Upload menu for the Master STB.
• USB Explore (Optional): Select a Software file by using the Arrow (▲/▼) or Page (+/-)
buttons and press RED (MoSAic) button for software downloading.
Parental Lock
You can lock the channels to prohibit unauthorized users from watching specific channels. Press
the Menu ( ) button. Select Parental Lock using the Arrow (◄/►) buttons on the main munu
Parental Lock >> Channel Lock
Channel Lock
Whenever you want to see the locked channel you will be
prompted to enter the PIN Code in the dialog box.
1 Select Channel Lock using the Arrow (▲/▼) buttons on
the Parental Lock menu and press the OK button.
2 Select the channel that you want to use the Arrow (▲/▼),
PR+/-, Page (+/-), or Numeric (0~9) buttons and press the
OK button.
Selected channel will be displayed with locking-marked.
Press it again to clear.
Arrow (◄/►) buttons: Switches between TV and Radio
List.
3 Press the RED (MoSAiC) button to confirm.
4 Press the Blue (SAT) button to move PIG screen.
22 English
Chapter 5 >> Main Menu
Parental Lock >> Lock Control
Lock Control
Whenever you want to use the locked system you will be prompted to enter the PIN Code in the
request dialog box. Using Arrow (▲/▼) buttons and press OK button to select a lock status.
• System Lock: Select Lock or Unlock by using the
Arrow (◄/►) button. If Lock is selected, the front key
function will be blocked.
• Menu Lock: Select Lock or Unlock by using the Arrow
(◄/►) button submenu Lock control will be available
with PIN code.
• Lock mode: Select Once or Every time mode by using
Arrow (◄/►) button.
• Once: Input the pin code once on the channel change
with Parental Lock.
• Every time: Input the pin code every time on the
channel change with Parental Lock Save the changes
with OK button Press the Blue (SAT) button to move
PIG screen
Parental Lock >> Change PIN Code
Change PIN Code
You can create a new PIN code in this menu. “0000” is the
default password.
1 Select Change PIN Code using the Arrow (▲/▼) buttons
on the Parental Lock, System Lock, Menu Lock and
press the OK button.
2 Enter the old PIN code.
3 Enter the new PIN code.
4 Enter the new PIN code again to confirm.
Note
• Please keep in mind that the PIN code must be a four-digit number. In case you forgot
your PIN code, contact your local dealer.
Game
This product provides lots of games for your entertaining environment.
Select Game using the Arrow (◄/►) buttons on the main menu.
1 Select a game using the Arrow (▲/▼) buttons on the Game menu and press the OK button.
2 According to the instruction displayed on screen, you can enjoy games using the Arrow,
Numeric (0~9), and OK buttons.
English 23
Chapter 5 >> Main Menu
Multimedia
You can access to the multimedia function with USB, SATA and Ethernet device.
• Please switch off the system before connecting USB and SATA cable to STB.
Otherwise, this can be causing the system to malfunction!!
Multimedia >> USB
Connect USB stick or External HDD through USB connector.
Multimedia >> SATA (optional)
Connect the external HDD through SATA connector in the
rear panel.
•HDD must be compatible with FAT 32 file system.
If HDD is not compatible with FAT 32 File system,
you need to change the file system by using personal
computer with the format function.
1 Playing the media files
Select the media file with channel up/down buttons and
press OK button.
2 Software Update
Select S/W files with channel up/down buttons and press
Red key (Mosaic).
3 Deleting files
Select the files with channel up/down buttons and press Green key (Sleep).
4 Format
Press yellow key (Audio) to delete all the files in the
storage device.
• PVR function
In order to use PVR function, the storage device must
be connected through SATA or USB connector.
1) Record: Press Rec button during watching channel
2) Stop: Press Stop button to finish recording channel
3) Play: Press Play button to play the recorded programs
4) Fast Forward: Press FFR button to play in Fast
Forward mode to x16
5) Rewind: Press REW button to play in Rewind mode
to x8
6) Pause: Press Pause button to stop the program for a while
24 English
Chapter 5 >> Main Menu
7) Media player: press F2 to start the media player.
8) Time shift: Press F3 to start time shift function
9) File list: press text button to see the file list in the media player menu
Multimedia >> Ethernet
•Before starting setup, please check if the Ethernet cable
is connected to your receiver well.
1) TCP IP set up
Input the right information for the settings to the
followings.
TCPIP Type/ IP Address/ Net mask / Gateway/ DNS
Type/ DNS Server
2) FTP Explorer
Press O.K. to connect the FTP Server
Select file and press Red Key (Mosaic) for S/W
update.
Conditional Access
You can enjoy not only scrambled services using the Conditional Access Modules (CAM), but
also free-to air services, Types of common interface module and smart card differ depending
on the service provider. If you want to use conditional access modules, contact your service
provider or distributor.
• Without using the Conditional Access (CA) Modules, free-to-air services are available.
English 25
Troubleshooting
Troubleshooting
Problem
No display LED on the front panel.
Solution
Plug the power cord correctly.
No power supply
No picture.
Ensure that the STB is switched on.
Check the connection status.
Check channels and Video output status.
Poor picture quality.
Check the signal level
If this is too low, try adjusting the alignment
of your dish.
No sound.
Check the volume level of the TV and STB
Check the mute status of the TV and STB
Check the connection of audio cable.
Remote Control does not operate.
Point remote control directly towards your
receiver.
Check and replace batteries.
Check if anything blocks the front panel.
Service is not running or scrambled.
Make sure the smart card is appropriate for
the selected service.
You have forgotten your PIN code.
See chapter 5, “Parental Lock” in this
User’s manual.
26 English
Specifications
Specifications
TUNER & CHANNE
Input Frequency
47~870 MHz
Input connector
IEC Female (RF IN), IEC Male (RF OUT)
IF Frequency
36.125 MHz
FEC Mode rate
1/2,2/3,3/4,5/6,7/8
Demodulation
QAM
Constellation
16, 32, 64, 128 and 256 QAM
QAM System Clock
28.92Mhz
Switching Mode Power Supply
Input Voltage
AC90-250V~,50/60Hz
Power Consumption
MAX.50W (Standby: Less than 3W )
MPEG TS A/V Decoding
Transport Stream
MPEG-2 ISO/IEC 1318-1
Profile Level
MPEG-2 MP@ML
MPEG-2 MP@HL, MPEG-4 AVC/H.264 HP@L4
Aspect Ratio
4:3, 16:9, Letter Box
Video Resolution
1080i, 720p, 576p, 576i
Audio Decoding
MPEG-1, Musicam Layers 1 & 2
Audio Mode
Single channel/Dual channel/Joint Stereo/Stereo
Sampling Rate
32,44,1& 48KHz
System Resources
Main Processor
ST40 CPU core: 266MHz(STi7101)
Flash Memory
8 Mbyte (Optional Expand)
Video DDR SDRAM
64 Mbyte (Optional Expand)
System DDR SDRAM
64 Mbyte (Optional Expand)
EEPROM
8Kbyte
A/V & Interfaces
Digital output(HD)
HDMI(TMDS main video output)
YPbPr
TV-Scart & RCA(SD)
Video : CVBS / RGB output
Audio : L/R output
VCR-Scart(SD)
Video : CVBS output / CVBS input bypass
Audio : L/R output / L,R input bypass
Digital Audio output
Digital AC-3 Decoding output
Digital Audio Bitstream output(S/PDIF)
S-Video
Video : S-Video output
RS-232C
Transfer rate 115.2Kbps, 9 pin D-sub type
PVR Ready(Optional)
USB2.0 High speed host controller
Serial ATA hard-disk drive support
Network (Optional)
Fast Ethernet (10/100)
English 27
Specifications
Specifications
Conditional Access System
PCMCIA (Optional)
2 Slot of DVB-CI
Smart Card(Optional)
2 Smart card Reader for Embedded CAS like
Front panel
Display
Dot-Matrix VFD (Vacuum Fluorescent Display)
Keys
Touch pad 7Keys
Accessories
RCU
IR(Freq. : 38Khz), Battery : 2x1.5V AAA
HDMI Cable
1.5M
Manual
Physical Specification
Size (W x H x D)
375 x 60 X 230mm
Net Weight
3.5Kg
Operation Temperature
0~50 C
Storage Temperature
-10~+60 C
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicates that it
should not be disposed with other household wastes at the end of its
working life.
To prevent possible harm to the environment or human health from
uncontrolled waste disposal, Please separate this from other types of
wastes and recycled it responsibly to promote the sustainable reuse
of material resources.
Household users should contact either the retailer where they
purchased this product, or their local government office, for details of
where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial wastes for disposal.
IM24 - 101012 [ENGLISH]
28 English
Rev.01