Cartridge Program - Oil Control

Cartridge Program - Oil Control
The Drive & Control Company
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
INDEX
General Information
03
Mechanical Data
23
Solenoid Data
26
Pressure Control Valve
32
Special Valves
42
Check Valves
44
Counterbalance Valves
45
Flow Control Valves
59
Logic Elements
69
Directional Valves, Mechanically Operated
75
Shuttle Valves
78
Solenoid Valves
80
Coils
101
Manifolds
103
Cavities
116
Prefered Itens
126
Cartridge Valves - RC X BROC
127
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
Hydraulic valves
for mobile applications
RE 64 020-B1/08.05
General Information
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
What you need to know about these Operating Instructions
These Operating Instructions apply to Rexroth hydraulic valves for mobile applications and consist of the following
three parts.
Part I
General Information RE 64 020-B1
Part II
Product-specific Instructions
Part III
Technical Datasheet
If you do not have all three parts, please request the missing part from Bosch Rexroth AG.
Only if all the information contained in all parts of the three-part Operating Instructions is observed
can safe operation of the Rexroth hydraulic valve be ensured.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
Contents
1
2
3
4
5
6
7
General
4
1.1
Scope of application of these Operating Instructions
4
1.2
To assist your understanding of these Operating Instructions
4
1.3
Further important and applicable documents
4
Responsibilities
5
2.1
Liability and warranty
5
2.2
Responsibilities of the operator/user
5
Important basic safety instructions
6
3.1
Proper use
6
3.2
Improper use
7
3.3
Requirements for personnel, duty of care
7
3.4
Ancillary dangers and protective measures
9
3.5
Disposal
10
Pressure fluids
11
4.1
General information on pressure fluids
11
4.2
Malfunctions due to contamination of pressure fluid
11
4.3
Topping up / refilling
12
Storage and longer standstills
13
5.1
Storage conditions
13
5.2
Corrosion protection
13
5.3
Ageing during storage and longer standstills
13
Assembly and bringing into first use
14
6.1
Before bringing into first use
14
6.2
Bringing into first use, subsequent bringing into use
16
Maintenance
18
7.1
Definitions of terms
18
7.2
Safety during maintenance tasks
19
7.3
Inspection and servicing
20
7.4
Repair
20
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
1
General
1.1
Scope of application of these Operating Instructions
These Operating Instructions apply to Rexroth control and regulating valves for mobile
control systems.
These Operating Instructions are intended for the use of the system manufacturer and the
designer as well as the operator.
The designer can be a person that is responsible for the design of a hydraulic system in
which Rexroth valves are used.
1.2
To assist your understanding of these Operating
Instructions
Cross-references are printed in italics.
DANGER
This symbol of danger indicates high risk, danger of loss of life or of serious injury.
WARNING
This symbol of danger indicates medium risk, injury and serious damage to property.
CAUTION
This symbol of danger indicates slight risk and possible damage.
Important
This symbol indicates additional information.
1.3
Further important and applicable documents
For system manufacturers and users, in addition to the Operating Instructions, the relevant
installation drawing issued by Bosch Rexroth AG shall apply.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
2
Responsibilities
2.1
Liability and warranty
Bosch Rexroth AG is not liable for damages that result from non-compliance with or
disregard of this user’s manual.
Any modification of the Rexroth valves beyond the extent described in these Operating
Instructions shall render the warranty and, if applicable, any further concessions granted,
null and void.
Bosch Rexroth AG shall only be liable if the scope of delivery was shown to be defective.
Bosch Rexroth AG shall not be liable if a deficiency occurs that involves parts having been
replaced by the customer with equivalent but not identical parts as specified by the
manufacturer.
2.2
Responsibilities of the operator/user
Users and operators of the Rexroth valves are responsible for the proper use of these valves.
Users and operators must ensure that the Rexroth valves are stored, used, operated and
maintained only in accordance with the proper use as defined in these Operating
Instructions.
Any maintenance tasks specified in these Operating Instructions must be carried out at the
specified intervals.
WARNING
Mineral-oil-based pressure fluid is hazardous to health and water; it may also be
flammable.
It may only be used if the relevant safety datasheet from the manufacturer is
available and all the measures stipulated therein have been implemented.
Important
The Operating Instructions supplied by Bosch Rexroth AG – in all its parts and with all
other relevant applicable documents – contain safety-related information that must be
included by the system manufacturer/user in the Operating Instructions to be written for the
final product.
A wide range of dangers can arise from the combined actions of the Rexroth valve and the
machine or system in which the valve is installed.
System manufacturers, users or operators must therefore ensure that the Rexroth valve is
only installed if it is suitable, without restrictions, for the proposed application at the
installation location.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
3
Important basic safety instructions
3.1
Proper use
Rexroth valves have been designed and constructed for the control and regulation of energy
and signals using a flow of oil. The safety components integrated into the Rexroth valves
satisfy at least Safety Category 1 in accordance with EN 954-1.
However, only by carefully observing these Operating Instructions can accidents be prevented and problem-free operation of your Rexroth valve be guaranteed.
Use the Rexroth valve only as described in these Operating Instructions and if it is stored,
installed, operated and maintained in accordance with the technical data, operating and
ambient conditions as defined in these Operating Instructions. The limiting values given in
Part III, Technical Datasheet must be observed.
Information on storage and longer standstills is given in 5 Storage and longer standstills.
Rexroth valves may only be operated if they are in perfect technical condition.
The Rexroth valve must be operated only with the pressure fluids intended for the purpose
specified in Part III, Technical Datasheet . Information on using the Rexroth valve with
different pressure fluids is available on request.
The Rexroth valve must be used only for the purpose specified in Part III, Technical
Datasheet. The connections, operating conditions and performance data defined in these
Operating Instructions must not be changed.
Important
If you wish to use the Rexroth valve with connections, operating conditions and
performance data or for purposes other than those defined by Bosch Rexroth AG in these
Operating Instructions, you should contact Bosch Rexroth AG in advance. The Rexroth
valve must not be used with connections, operating conditions and performance data or for
purposes other than those defined in these Operating Instructions without the written
agreement of Bosch Rexroth AG.
Rexroth valves may only be converted within the scope given in Part II, Product-specific
Instructions.
During setting up or maintenance work, unless impractical, the safety devices fitted by
Bosch Rexroth AG must be present, properly installed and in full working order. They
must not be relocated, bypassed or rendered ineffective.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
3.2
Improper use
Modifications and/or conversions of a Rexroth valve are only permissible within the scope
given in Part II, Product-specific Instructions.
Tamperproof lead seals installed by Bosch Rexroth AG shall not be removed or damaged
except when this is necessary in the course of maintenance tasks defined in the Operating
Instructions.
Rexroth valves for which these Operating Instructions apply shall not be used in potentially
explosive atmospheres. Special Rexroth valves are available that can be used in potentially
explosive atmospheres.
Pressure control valves without a type examination in accordance with the EU Pressure
Equipment Directive must not be used as safety valves in safety-related applications.
The nameplate must not be removed or painted over.
3.3
Requirements for personnel, duty of care
3.3.1 General requirements, qualifications
Rexroth valves must never be operated or maintained by persons under the influence of
alcohol, drugs or other medication which affect one’s ability to react.
Persons under the age of 18 who are currently receiving instruction or training or are working
under supervision may not work on Rexroth valves.
This does not apply to young persons of 16 or over if
−
−
working on Rexroth valves is necessary in order for them to accomplish their training
objective
their protection is guaranteed by the supervision of an experienced, competent person
and they are allowed to use only tools, materials and protective gear that preclude the
risk of injury.
Specialist personnel are those who, using their specialist training, knowledge and experience
as well as familiarity with the relevant conditions, can recognise possible dangers and undertake the necessary measures to eliminate possible accidents.
3.3.2 Requirements for maintenance personnel
It may be necessary to carry out maintenance tasks on the Rexroth valve in order to keep it in
proper working order. For details please refer to Part II, Product-specific Instructions.
Maintenance tasks include inspection, servicing and repair of hydraulic and electrical components. The personnel carrying out these various tasks must have certain minimum
qualifications.
For inspections of the external parts of hydraulic components, the personnel must fulfil the
following requirements:
−
they must be instructed about the tasks,
−
Specialist knowledge of hydraulics is not required.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
For maintenance of the hydraulic components, the personnel must fulfil the following
requirements:
−
They have been instructed in the relevant activity.
−
Specialist knowledge of hydraulics is required.
For maintenance of the Rexroth valves, the personnel must fulfil the following requirements:
−
The personnel must be hydraulics experts instructed in the tasks as defined above.
−
The personnel must be familiar with the function of the hydraulic system as a whole, from
subsystems to their interaction with the function of the machine as a whole.
−
The personnel must be able to read hydraulic circuit diagrams, interpret individual functions from their symbols and understand function diagrams.
−
The personnel must possess knowledge of the function and construction of hydraulic
elements in general and of the Rexroth valves to be maintained in particular.
See also 7.4 Repair.
For work on the electrics, the following applies:
All work on electrical equipment may only be carried out by an authorised, qualified electrician, or by instructed persons under the guidance and supervision of an authorised
qualified electrician, in accordance with the rules applicable to electrotechnical products.
For work on the software, the following applies:
Modifications of the software may only be carried out by bodies authorised to do so by
Bosch Rexroth AG.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
3.4
Ancillary dangers and protective measures
DANGER
Danger zone
Ancillary danger
Protective measure(s), safety instructions
Connections and
pressure lines (pipes
and hoses)
Risk of injury or loss of life from
sprayed pressure fluid under high
pressure during maintenance work.
Depressurise the hydraulic system before starting
maintenance work. Relieve any accumulators of
pressure.
Rectify leaks immediately.
There is a health hazard if escaping
pressure fluid comes into contact
with the skin. This is a particular
risk if the tank is at a higher level
during repair work
Tanks installed above the valve being repaired must
be emptied before work is started.
Surfaces of components and pressure
lines
Risk of burning due to high surface
temperatures
Allow hydraulic parts to cool before commencing
maintenance work.
Electrical
components
Electric shock
Wear protective clothing.
Work on electrical components only in the nonpowered state.
Switch electrical connections off before assembly
and disassembly work starts.
All tasks that require product components to be
dismantled must be performed only within the
scope given in Part II, Product-specific Instructions.
Failure caused by excessive
moisture entry following cleaning
with a high-pressure cleaner
Shield the valve from the direct effect of highpressure water jets.
Handling pressure fluid without protection is hazardous to health.
Please observe the manufacturer's safety instructions and the relevant safety datasheets for
the pressure fluid that you are using.
Serious damage to health or death may result if pressure fluid enters the blood stream or is
swallowed. Contact a physician immediately if pressure fluid has entered the blood stream
or has been swallowed.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
CAUTION
Risk of environmental pollution
Danger zone
Ancillary danger
Protective measure(s), safety instructions
Connections and
pressure lines (pipes
and hoses)
Water or ground pollution due to
leakage
Use a collecting trough.
Important
Rectify leaks immediately.
Also see 2.2 Responsibilities of the operator/user.
3.5
Disposal
Completely empty valve and dispose as scrap metal.
Important
To completely empty means that the valve must be properly emptied so that no more
pressure fluid can drip out.
The valve does not need to be cleaned when it is completely empty.
Collect residual pressure fluid and dispose of it in accordance with the instructions given in
the safety datasheet of the pressure fluid.
Dispose of electronic products in accordance with the applicable regulations.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
4
Pressure fluids
4.1
General information on pressure fluids
The effectiveness of pressure fluid diminishes as it ages (undergoes chemical changes).
Acids and resinous residues form that may cause moving parts inside the valves to stick.
The following factors accelerate the ageing process:
Important
−
high temperatures
−
oxygen in the pressure fluid
−
air humidity
−
water
−
metallic catalysts
−
high operating pressure
−
contaminants.
Observe the following rules of thumb:
At pressure fluid temperatures > 70 °C, the rate of ageing doubles for every 10 °C.
Further information on mineral-oil-based pressure fluids, also concerning Rexroth valves,
can be found in our publications RE 90 220 Mineral-oil Based Pressure Fluids and
RE 90 220-1 Hydraulic Fluids on Mineral Oil Basis for Axial Piston Units.
4.2
Malfunctions due to contamination of pressure fluid
Contaminants of the pressure fluid lead to malfunctions, increased wear and a shorter
service life of the hydraulic product. This can have negative effects on the safety and
reliability of the hydraulic product.
Therefore the maintenance tasks specified in the Operating Instructions of the hydraulic
system shall be carried out at regular intervals and the utmost cleanliness is required during
work on the hydraulic product.
Contamination of the pressure fluid can be caused by:
−
Wear during operation of the machine/system
(metallic and non-metallic abrasion)
−
Leaks of the hydraulic product
−
Contaminants introduced during servicing/repair
−
The use of dirty (unfiltered) pressure fluid when the pressure fluid is changed.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
4.3
Topping up / refilling
When topping up / refilling your hydraulic system, make sure that you use pressure fluid of
the same sort and type and from the same manufacturer.
If the fluid is heavily contaminated or prematurely aged, then the system, including the tank
must be cleaned and flushed before refilling. New pressure fluid must always be filtered in
accordance with the required cleanliness class, as it does not normally meet the required
cleanliness class in the as-supplied state. Flush out lines and hoses before installation.
Use a filter unit to fill the pressure fluid tank. Ensure that the filter element is clean. Do not
remove the filter strainers from filler necks or the filter element from filters before filling the
pressure fluid tank.
Important
The fineness of the filter shall correspond to the cleanliness class required by the overall
system and if possible be even finer. The filter unit used shall fulfil the requirements for
functional safety and service life.
If possible, fill the pressure fluid tank via a filling coupling, if possible using a filter in the
return line.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
5
Storage and longer standstills
5.1
Storage conditions
Store the Rexroth valve only in a dry, dust-free atmosphere that is free of corrosive agents
and vapours, has a low moisture content and no large variations in temperature.
5.2
Corrosion protection
Rexroth valves are tested with mineral oil in the factory. This oil protects sealed valves
against internal corrosion.
Unpainted valves or those that only have a galvanic coating are not protected against
corrosion.
Delays in bringing into use, long shipping and storage times or long periods of non-use can
lead to rust formation in Rexroth valves. Additional corrosion protection measures must be
implemented to prevent this.
5.3
Ageing during storage and longer standstills
Long storage times or long periods of non-use of Rexroth valves leads to damage of seals
and plastic parts.
External seals of valves that have been stored for more than 12 months must be checked for
damage before they are installed. They must be replaced, if necessary.
All externally acting seals must be replaced after a storage time or standstill period of
3 years. Seal sets can be ordered from Bosch Rexroth AG.
Every time the unit is brought into use, the valves must be checked that they are not leaking
to the outside, see 6 Assembly and bringing into first use. If there is a leakage, the seals
must be replaced.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
6
CAUTION
Assembly and bringing into first use
Risk of injury and damage
Wear safety gloves to avoid being injured by sharp edges.
Assembling and bringing into (first) use shall only be done by an instructed,
authorised hydraulics expert who has the required specialist knowledge.
Pay attention to cleanliness:
−
−
Do not use cleaning wool or cloths containing fibres for cleaning. Depending on the condition of the system or machine, cleaning with fibre-free cloths may be sufficient. Use
suitable liquid cleaning agents to remove lubricants and other stronger contaminants.
Make sure that cleaning agent does not get into the hydraulic system.
Use only sealing elements specified in Part III, Technical Datasheet.
6.1
Before bringing into first use
1. Check the delivery for completeness and transport damage.
2. Check whether the seals are present for all connections and that they are in a perfect
condition.
3. Check that the Operating Instructions for the Rexroth valve are present and complete.
Contact us if the Operating Instructions are incomplete.
4. If the valve is to be painted prior to assembly, then
¾before painting, protect all hydraulic connections from being covered in paint by fully
inserting plastic screw plugs
¾protect any fastening threads from being covered in paint by inserting a screw
¾carefully mask the flange surfaces of the valves as well as the subplates and endplates before painting to prevent dirt and paint from entering
¾mask plastic plugs of the electrical connections and make sure not to damage the
plugs in any way.
A removable foil has been applied to the nameplate in the factory to protect them during
painting.
When removing the plastic screw plugs, ensure that paint splinters do not get into the
valve.
5. Mount the Rexroth valve.
¾Use the intended seal for each hydraulic connection.
¾Mount and fit the pipes to the Rexroth valve so that they are free of strain.
¾Tighten the fastening bolts evenly with the specified tightening torque. Only fastening materials specified in the Operating Instructions are to be used.
6. Ensure that the interfaces of the system/machine and the installation conditions provide
for safe operation of the Rexroth valve. If in doubt, consult the people responsible for the
overall system / functional machine.
7. Based on the operating instructions for the system or machine in which the Rexroth valve
is to be installed, check whether bringing the hydraulic system into use could lead to
uncontrolled, dangerous movements. Where appropriate, take into account the hazard
analysis / risk assessment for the system or machine.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
8. Take the precautions appropriate to the anticipated dangers, e. g.:
¾Ensure that the cylinder piston rod can move out without danger.
¾Use a hoist or other lifting device to additionally secure lifted loads.
9. As part of bringing into (first) use, check whether the electric motors and valve solenoids
can be switched manually using the electrical controls of the system/machine. If they
cannot be switched manually or they can but with difficulty you must provide a remote
control (e. g. test boxes for Rexroth proportional valves) for the internal function test of
the hydraulic system.
10. Draw up a sequential program for bringing into (first) use and store it with the technical
documentation as an appendix to the Operating Instructions.
11. Divide the functional circuit diagram into separate mini-circuits that can each be started
up in succession.
12. Read the functional circuit diagram and seek clarification of any unclear text or diagrams.
More information on the functioning of subassemblies is given in the Technical
Datasheet.
13. Establish into which position valves are to be switched, or how valves are to be set.
14. Put up any necessary directional, prohibitive or informative signs and check whether the
meaning of these signs is explained in the Operating Instructions.
15. Follow this sequence for bringing into (first) use
−
Pump circuit
−
Parts of the control system: e. g. pressure cut-off and switchover, open centre,
pressure reduction, etc.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
6.2
Bringing into first use, subsequent bringing into use
¾Take suitable precautions when bringing into first use to maintain the required purity of
the pressure fluid.
−
Make sure that the quality of the pressure fluid is not diminished by contaminants in
the system.
−
Completely remove any oil residues left over from the factory test.
−
Remove any gummed oil which may have formed due to incorrect storage.
¾Connect all connection lines in accordance with the installation instructions provided by
the manufacturer of the connectors.
DANGER
Danger due to pressure fluid escaping with a high pressure.
Wear safety goggles and safety gloves!
Make sure that pipes and hoses are connected at all ports or that the ports are
sealed with screw plugs.
Carry out a special check to make sure that the union nuts and flanges are correctly
tightened at the pipe connections and flanges.
¾Set the pressure and flow control valves, pump regulator, signalling elements such as
pressure switches, limit switches and temperature regulators to the settings and values
defined in the sequential program (see 6.1 Before bringing into first use).
DANGER
Dangers due to malfunctions
Do not change the settings of valves with a safety function, valves with a position
switch or valves with preset electronics.
¾Do not remove the lead seals. Damaged or removed lead seals indicate improper use of
the hydraulic product.
¾Bleed the hydraulics (valve, pump, motor, line, cylinder). Bleed the hydraulics lines to
consumers or measuring points at the highest point, if possible. Before bringing into use,
the valve must be filled with pressure fluid and the system in which the valve is installed
must be completely bled.
Important
Details on bleeding can be found in the Operating Instructions of the respective system.
Important
Details on fine-tuning can be found in the Operating Instructions of the respective system.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
¾Check the operating temperature after the machine has been running continuously for
several hours. Too high an operating temperature indicates that there are faults that need
to be analysed and rectified.
¾After bringing the machine into first use, have a sample of the pressure fluid analysed to
ensure that it achieves the required cleanliness class. Change the pressure fluid if the
required cleanliness class is not achieved. If the pressure fluid is not tested in the laboratory after bringing the machine into first use: Change the pressure fluid.
Important
Information on how to perform the function test and pressure test can be found in the
Operating Instructions of the respective system.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
7
Maintenance
7.1
Definitions of terms
The term "Maintenance" as defined in DIN 31051 encompasses all measures to maintain
and restore the desired conditions and to determine and assess the actual condition of the
technical devices of a system.
These measures are divided into the following categories:
−
Inspection (determining the actual condition)
−
Servicing (maintaining the desired condition)
−
Repair (restoring the desired condition).
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
7.2
DANGER
Safety during maintenance tasks
Dangers due to reduced safety during repair work
Experience has shown that the number of accidents is higher during repair work than
during normal operations. Therefore, in the interests of safety, please observe all the
following safety instructions at all times.
¾Regularly check any safety devices – if installed – for their correct functioning.
¾Perform all maintenance work properly, completely and within the stipulated
periods and make a record of the work.
¾Cordon off the maintenance zone at a sufficient distance before commencing
work.
¾Pay attention to cleanliness to avoid malfunctions caused by contamination.
¾Exercise extreme vigilance when operating the hydraulic product in maintenance
mode, which may in certain circumstances necessitate the temporary removal of
certain safety devices. Switch off the hydraulic system and secure it against being
unintentionally switched on again.
¾The set values of safety valves shall not be altered by the user. Any readjustment
shall be performed by authorised testing bodies only.
¾Wear safety goggles, safety gloves and safety shoes. Depressurise the hydraulic
product, relieve the pressure in any pressure accumulators.
¾Allow pressure lines and sections of the system which have to be opened to cool
down before commencing maintenance work.
¾Open with care any segments that have to remain under pressure.
¾Note that if check valves are located in the pressure lines above the pumps, the
hydraulic system may still be under pressure even after it has been disconnected
from the actual pressure supply. Advance all cylinders to their safe end position.
¾Lower all loads. Use an external support if it is not possible to lower a load. Never
perform any maintenance work on raised units without external support.
¾Switch off all pumps.
¾Mechanically support vertical cylinders so that they cannot descend.
¾Only new, interchangeable and tested components, replacement parts and
lubricants in original-equipment quality are approved for use/replacement.
¾For reasons of safety, the installation of untested components is strictly
prohibited.
¾Make sure that all safety devices are properly installed and have undergone a
function test before bringing the system (back) into use.
¾Remove all tools and materials needed for maintenance from the hydraulic
product after the work has been completed.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
7.3
Inspection and servicing
The objective of inspection and servicing is
−
to maintain all system functions along with the initial parameters of the system
−
to ensure continual availability of the system
−
to detect weak points
−
to ensure that the system attains the required service life.
We strongly recommend the use of an inspection and servicing book, in which all work
specific to the system and the site, and all inspection and servicing intervals should be
defined and documented.
Important
The product-specific inspection and servicing plan for the Rexroth valve can be found in
Part II, Product-specific Operating Instructions.
7.4
Repair
All repairs of Rexroth valves must be carried out only by workshops authorised by
Bosch Rexroth AG.
Bosch Rexroth AG
Hydraulics
Robert-Bosch-Straße 2
71701 Schwieberdingen, Germany
Fax
+49 (0) 7 11 / 811-1798
info.brh-stf@boschrexroth.de
www.boschrexroth.de
© This document, as well as the data, specifications and other information
set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be
reproduced or given to third parties without its consent.
The data specified above only serve to describe the product. No statements
concerning a certain condition or suitability for a certain application can be
derived from our information. The given information does not release the user
from the obligation of own judgement and verification. It must be remembered that our products are subject to a natural process of wear and aging.
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
TECHNICAL DATA
TECHNICAL DATA
HYDRAULIC FLUID
General properties: it must have physical lubricating and chemical properties suitable for use in hydraulic
systems such as, for example:
- MINERAL OIL BASED HYDRAULIC FLUIDS HL
(DIN 51524 part 1)
- MINERAL OIL BASED HYDRAULIC FLUIDS HLP
(DIN 51524 part 2).
For use of environmentally acceptable fluids (vegetable or polyglycol base) please consult BROC.
Viscosity class: according to ISO-DIN, it is expressed by the ISO-VG number which indicates the average
NLQHPDWLFYLVFRVLW\DWƒ&ƒ)±PP2VRUFHQWLVWRNHV±F6W
Test conditions: the main performance curves and specifications shown in this catalogue are obtained using
mineral based fluid ISO VG 46, with a cleanliness class of 17/14 - 18/14 ISO 4406 (8-9 NAS 1638), at a
temperature of 30/40°C (86/104°F). More detailed technical characteristics are available at BROC.
Fluid temperature range: the valves are designed for fluids at a temperature between -30°C and +100°C (-22°F
and +212°F). For temperatures outside this range, consult BROC.
Internal leakage: most BROC valves have a leak proof seat design, but there are different families of valves
each providing a different level of sealing depending on the type and number of the poppets; the leakage features
of each valve type must be selected in order to suit the application.
The table A (pg. A-PD3) shows the AVERAGE LEAKAGE for various valve families; the readings are achieved in
the specified test conditions, and are measured in cm3/min or drops/min.
The ratio between them is:
1 cm3/min (0.06 in3/min) = 15y20 drops/min.
For pressure relief valves the leakage is indicated at re-seating conditions, identified as X% of pressure relief
setting.
CLEANLINESS (see table B, pg. A-PD3)
General information: the cause of malfunctions in hydraulic systems and components is often found to be
excessive fluid contamination. The hard contaminant particles in the fluid wear the hydraulic components and
prevent the poppets from re-seating, with consequent internal leakage and system inefficiency. For the correct
operation of BROC valves it is necessary to ensure a fluid cleanliness class at least 19/15 ISO-4406, or 10y11
NAS-1638, unless otherwise specified in the relevant technical sheet.
Filtration ratio (Ex): FKDUDFWHULVWLFRIHDFKW\SHRIILOWHULW¶VWKHUDWLREHWZHHQWKHQXPEHURISDUWLFOHVEHIRUHDQG
after the filter with diameter larger than X micron.
Absolute filtration rating (ISO 4572): the diameter X of the largest particles with Ex t 75.
Contamination class ISO 4406: expressed by two numbers respectively representing the number of particles
larger than 5 ȝm and larger than 15 ȝm contained in 1 ml of fluid.
Contamination class NAS 1638: expressed by one number representing the number of particles of different
size ranges contained in 100 ml of fluid.
Rev.0306
Page A-PD2
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
TECHNICAL DATA
DATA
TECHNICAL
Rev.0605
Page A-PD3
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
TECHNICAL DATA
TECHNICAL DATA
PRESSURE SETTING: BROC valves are supplied pre-set at the standard pressure setting shown by the
relevant catalog sheet. Whenever the application requires a re-adjustment, please ensure that the limits of the
indicated pressure range are never exceeded.
SEALING OF VALVE ADJUSTERS: plastic sealing caps are available for most cartridge valves.
The cartridges can be purchased Factory sealed.
INSTALLATION OF CARTRIDGE VALVES:
Procedure to be followed for correct installation of the cartridge valves in their cavities:
ensure that seals and back-up rings are flawless and correctly installed;
check that both the cartridge and the cavity are clean, without contamination;
dip the cartridge in clean oil;
insert the cartridge into the cavity and screw it in by hand, until you begin to compress the top o-ring
tighten with a calibrated torque wrench up to the specifications shown in the catalogue.
STORAGE OF NEW VALVES:
the valves shall not be exposed to direct sun light nor to sources of heat or ozone (like electric motors running),
and should be stored in their original, protective wrapping at a temperature between -20°C and +50°C (-4°F and
+122°F).
Rev.0306
Page A-PD4
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
TECHNICAL DATA
TECHNICAL DATA
CONTINUOUS DUTY COILSCONTINUOUS
- ED 100%
DUTY COILS - ED 100%
WORKING DUTY
DIN VDE 0580
The working duty ED of a coil is the ratio between
energized time ti and full cycle time tc where tc = ti + tr
and tr = de-energized time.
ED = ( ti / tc ) Ã 100
INLET VOLTAGE
To obtain correct operation and long life of coils it is
necessary that operating voltage fluctuations do not exceed
± 10 % of nominal voltage.
%
HEAT INSULATION
ALL COILS ARE RATED FOR ED = 100 %
PROVIDED THAT TEMPERATURE LIMIT OF THEIR
INSULATION CLASS IS NOT EXCEEDED.
All COILS
COMPLETE COIL
Copper wire
PROTECTION
DIN 40050 Part 9 - EN 60529
Protection class is designated by the letter IP followed by
two digits: the first indicates protection against penetration
of foreign solid bodies, the second against penetration of
water. Protection class doesn’t apply to explosion risks or
to conditions such as moisture, corrosive agents, mildew
etc.
IP65 MEANS WATER PROTECTION AGAINST:
x LOW PRESSURE JETS
Water at 43.5 psi (0.3 bar) pressure sprayed from a
distance of 8.2 - 9.8 ft (2.5 – 3 m) from every direction.
Coils CANNOT BE PLUNGED INTO WATER OR REMAIN
UNDER WATER.
IP67 MEANS WATER PROTECTION AGAINST:
x 30 MINUTES IMMERSION AT 3.3 ft (1 m) DEPTH
IP69K MEANS WATER PROTECTION AGAINST:
x HIGH PRESSURE AND TEMPERATURE JETS
Water at 1160 - 1450 psi (80-100 bar) pressure and 167 185°F (75-85°C) temperature sprayed from a distance of
3.9 - 5.9 in (100 - 150 mm) from every direction.
PROTECTION
THERMAL SHOCK DUNK TEST
This test, well known and commonly applied in the
construction, agricultural and mobile equipment markets,
includes several steps :
1) Coil is continuously energized for 1 hour at nominal
voltage (ambient temperature 77°F (25°C)) or heated
for 2 hours in oven at 221°F (105°C) (coil not
energized)
2) Coil is immediately immersed in water at 68 - 77°F (20 25°C) for 30 minutes (minimum depth 11.8 in (300 mm))
3) Coil, when still wet, is tested for moisture ingression
and dielectric breakdown with the “Hypot test”. Using
an instrument for testing dielectric strength, 500 VDC
is supplied between winding and external surface of
the coil and current leakage is measured. Current
leakage must not exceed 100 micro-amps
4) Complete cycle is repeated for 5 times minimum on a
sample of 10 coils minimum
DIN VDE 0580
CLASS
H
365qF (180qC)
392qF (200qC)
These are the maximum allowable absolute temperatures T
= TA + 'T where TA = ambient temperature and
'T
= temperature rise due to operation.
For example, if TA = 104qF (40qC) we obtain 'Tmax =
239qF (115qC) if we have to comply with the limit of 311qF
(155qC) and 'Tmax = 284qF (140qC) if we have to comply
with the limit of 365qF (180qC).
The temperature rise 'T is calculated from resistance at
ambient temperature and resistance at stabilized
temperature, measured according to DIN VDE 0580:
x coil is mounted on a standard cartridge valve size 06
inserted in a standard steel manifold on a wooden
surface.
x coil is kept energized for 1 hour at nominal voltage, with
ambient temperature TA = 68 - 77qF (20-25qC) and
natural ventilation.
CLASS H COILS ARE NOT RATED FOR CONTINUOUS
DUTY ED = 100 % IF AMBIENT TEMPERATURE
EXCEEDS THE VALUE Tx = 365 (180) - 'T qF (qC)
IN ANY CASE FREE HEAT EXCHANGE AND NATURAL
VENTILATION ARE NECESSARY FOR THE CORRECT
OPERATION OF COILS.
EXTERNAL TEMPERATURE of coils is not directly related
with 'T. After few minutes of continuous energization
temperatures up to 176-212qF (80-100qC) can be reached,
so care should be taken to avoid accidental contact of
people with hot surfaces.
AC SERVICE
All OIL CONTROL’s solenoid valves are designed to
operate only with DC power supply. All windings are DC.
AC service is possible using DIN 43650 connectors with
rectifier (see page 1.71.010).
All coils with DIN 43650 connector correctly mounted
have IP65 protection.
S8-356, S7 and S5 coils with integrated Deutsch DT042P connector have IP69K protection and have passed
the thermal shock dunk test.
Rev.06.05
7.01.010.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
TECHNICAL DATA
DATA
TECHNICAL
STANDARD
MANUAL
STANDARD MANUAL OVERRIDE
OVERRIDE OPTIONS
OPTIONS
SCREW-OUT KNOB STYLE
AVAILABLE ON FOLLOWING MODELS:
x
x
x
x
x
2 way 2 position pilot operated normally closed series 8A / 8I
2 way 2 position direct acting poppet style normally closed series 8I
2 way 2 position direct acting double lock normally open series 8I
3 way 2 position spool style series 8I / 7I
4 way 2 position spool style series 8I / 7I
OPERATION
To operate manual override, screw out the knob turning it counterclockwise.
To return to normal valve operation, turn the knob clockwise.
SCREW-IN STYLE
AVAILABLE ON FOLLOWING MODELS:
x
Proportional valves series 5A
OPERATION
To operate manual override, screw in the pin turning it clockwise with wrench.
To return to normal valve operation, turn the bolt counterclockwise.
PUSH STYLE
AVAILABLE ON FOLLOWING MODELS:
x
x
x
2 way 2 position pilot operated normally open series 8A / 8I
2 way 2 position direct acting poppet style normally open series 8I
2 way 2 position direct acting double lock normally closed series 8I
OPERATION
To operate manual override, push and hold override button.
To return to normal valve operation, simply release the button.
AVAILABLE ON FOLLOWING MODELS:
x
x
2 way 2 position direct acting double lock normally closed series 7A
3 way 2 position direct acting poppet style series 7A
OPERATION
To operate manual override, push and hold override button with tool.
To return to normal valve operation, simply release the button.
PUSH AND TWIST STYLE
AVAILABLE ON FOLLOWING MODELS:
x
x
x
2 way 2 position pilot operated normally open series 8A / 8I
2 way 2 position direct acting poppet style normally open series 8I
2 way 2 position direct acting double lock normally closed series 8I
OPERATION
To operate manual override button, turn clockwise and release.
To return to normal valve operation, push override button, turn counterclockwise and
release.
PUSH AND PULL STYLE
AVAILABLE ON FOLLOWING MODELS:
x
4 way 3 position spool style series 8A / 7I
OPERATION
To operate manual override, push to override S2 coil or pull to override S1 coil and
hold override button.
To return to normal valve operation, simply release the button.
Rev. 06.05
7.01.020.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
TECHNICAL DATA
TECHNICAL DATA
SPECIAL MANUAL OVERRIDE
OPTIONS
SPECIAL
MANUAL OVERRIDE OPTIONS
PULL STYLE
CABLE
HAND
OPERATED
OPERATED
AVAILABLE ON FOLLOWING MODELS:
x
2 way 2 position pilot operated normally closed series 8A size 06
OPERATION
To operate manual override, pull and hold the knob. This override is not detented.
Force required to operate is approximately 11.2 lbs (50 N).
This override can also be remote operated by a cable fixed to the M8 thread. In this
case the spring may not provide enough force to overcome internal cable friction and
the user must provide an external means of returning the cable.
SAFETY
PUSH STYLE
AVAILABLE ON FOLLOWING MODELS:
x
x
x
2 way 2 position pilot operated normally open series 8A / 8I
2 way 2 position direct acting poppet style normally open series 8I
2 way 2 position direct acting double lock normally closed series 8I
OPERATION
To operate manual override, screw out the knob protection after removing wirelocking and push and hold override button.
To return to normal valve operation, simply release the button.
SAFETY
PUSH AND TWIST STYLE
AVAILABLE ON FOLLOWING MODELS:
x
x
x
2 way 2 position pilot operated normally open series 8A / 8I
2 way 2 position direct acting poppet style normally open series 8I
2 way 2 position direct acting double lock normally closed series 8I
OPERATION
To operate manual override, screw out the knob protection after removing wirelocking and turn clockwise and release override button.
To return to normal valve operation, push override button, turn counterclockwise and
release.
SAFETY
SCREW-IN STYLE
AVAILABLE ON FOLLOWING MODELS:
x
x
x
2 way 2 position pilot operated normally open series 8I
2 way 2 position direct acting poppet style normally open series 8I
2 way 2 position direct acting double lock normally closed series 8I
OPERATION
Safety manual override has been designed to avoid accidental operation of the
emergency device.
Manual override can be operated only screwing out the knob, removing the coil and
screwing the knob completely in again.
To return to normal valve operation it is necessary to turn out the knob and mount the
coil again.
Rev. 06.05
7.01.030.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
TECHNICAL
TECHNICAL DATA
DATA
HYDRAULIC FLUID
GENERAL PROPERTIES
VISCOSITY
Hydraulic fluid must have physical, lubricating and chemical
properties suitable for use in hydraulic systems such as, for
example
MINERAL BASED HYDRAULIC OILS HL DIN 51524 Part 1
MINERAL BASED HYDRAULIC OILS HLP DIN 51524 Part 2
VISCOSITY CLASS
ISO 3448 - DIN 51519
ISO viscosity class is expressed by ISO VG followed by
one number representing the medium kinematic viscosity at
2
104°F 40°C in mm /s or centiStokes cSt
KINEMATIC VISCOSITY
CLASS
Maximum
ISO VG 10
90
at 32°F (0°C)
Medium
Minimum
at 104°F (40°C) at 212°F (100°C)
2.4
10
ISO VG 22
300
22
4.1
ISO VG 32
420
32
5.0
ISO VG 46
780
46
6.1
ISO VG 68
1400
68
7.8
ISO VG 100
2560
100
9.9
FUNCTIONAL TESTING - TEMPERATURES - INTERNAL LEAKAGE
FUNCTIONAL TESTING
FLUID TEMPERATURE RANGE
All performance curves in this catalogue are obtained using
mineral based hydraulic oil with 46 cSt viscosity at 104°F
(40°C) (ISO VG 46 viscosity class).
All valves go through functional testing at these conditions
before shipment. Our test stands ensure 10 micron
ABSOLUTE FILTRATION.
All performance curves represent the average of real
values measured on tested valves. For this reason a
tolerance of ± 15-29 psi (1-2 bar) for pressure drop and ±
20-30 ms for response time has to be considered normal
and acceptable.
The electrical parameters and the response times of the
ON-OFF solenoid valves are measured using 24 V DC
coils at stabilized temperature and nominal voltage. Tests
on proportional valves are performed using 12 V DC coils.
-22°F (-30°C) to +212°F (+100°C)
AMBIENT TEMPERATURE RANGE
NON SOLENOID VALVES -22°F (-30°C) to +212°F (+100°C)
SOLENOID VALVES
SEE COIL PAGES
Please consult us for different temperature ranges.
INTERNAL LEAKAGE - POPPET VALVES
MAXIMUM ALLOWABLE INTERNAL LEAKAGE of all
poppet valves cannot exceed 0.06 in3/min (1 cm3/min) (1520 drops/min) at the maximum working pressure with 46
cSt oil viscosity. Actual leakage is expected, on average, to
be less than 10 drops/min and anyway tends to decrease
after few seconds.
SEALS
O - RINGS
Acryl - Nitrile Butadiene Rubber NBR ( BUNA-N ) standard for
temperatures between -22°F (-30°C) and +212°F (+100°C).
FLUOROCARBON FPM ( Viton ) and other compounds are
available on request.
BACKUP RINGS
LUBRIFLON - PTFE
SEAL KITS
SEAL KITS include ALL EXTERNAL SEALS. Internal seals
of cartridge valves are not included, since the customer is
not allowed to disassemble cartridge valves.
Rev.06.05
ORDERING CODE:
CARTRIDGE VALVES
Substitute OD with KD
VALVES IN STANDARD MANIFOLD Same as cartridge KIT
VALVES IN EMERGENCY MANIFOLD Substitute OE with KE
EXAMPLES:
VALVE CODE:
OD.15.32.18.18.00
SEAL KIT CODE:
KD.15.32.18.18.00
OS.15.32.18.18.02
VALVE CODE:
OE.15.05.18.37.02
SEAL KIT CODE:
KE.15.05.18.37.02
7.01.040.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
TECHNICAL DATA
TECHNICAL DATA
CARTRIDGE INSTALLATION
It is recommended to follow these steps:
x Inspect the cartridge to ensure that no external
contaminant is present.
x Check that O-ring and back-up rings are intact and
correctly positioned. The O-ring should be towards the
higher pressure port if only one back-up ring is present
or between double back-up rings if both ports receive
high pressure.
x
x
x
Inspect cavity for burrs or other machining irregularities
which could damage seals during installation.
Dip the cartridge in clean oil.
Screw the cartridge in BY HAND until the O-ring is met,
then tighten to the torque specified in the cartridge
catalogue page. Do not exceed maximum torque:
overtightening may cause valve failure.
IMPORTANT: Continuous high frequency vibrations especially if combined with pulsating pressure, may cause cartridge
unscrewing and consequent O-ring extrusion. Please consult our Technical Department.
COIL INSTALLATION
COIL WITH O-RING SEATS (S7 - S5)
COIL WITHOUT O-RING SEATS (S8-356)
It is recommended to follow these steps:
x Insert 1st O-Ring (see drawing)
x Insert coil
x Insert 2nd O-Ring (see drawing)
x Tighten BY HAND coil retaining nut to the torque
specified in the cartridge catalogue page.
It is recommended to follow these steps:
x Insert 1st O-Ring (see drawing)
x Insert coil
x Tighten BY HAND coil retaining nut to the torque
specified in the cartridge catalogue page. The 2nd ORing is fixed inside the nut.
Example:
Example:
Nut
2nd O-Ring
Nut
2nd O-Ring
Coil
Coil
1st O-Ring
1st O-Ring
IMPORTANT: O-rings are the only protection against water infiltration between tube and coil, which may lead in short time to
coil failure. The proper mounting of both O-rings is therefore necessary to ensure normal life of coils when operating in presence
of water, ice, moisture etc. Oil Control cannot guarantee any IP protection degree if both O-rings are not properly mounted on
coils.
Rev.06.05
7.01.045.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
TECHNICAL
TECHNICAL DATA
DATA
CONTAMINATION
CONTAMINATION -- FILTRATION
FILTRATION
GENERAL INFORMATION
ABSOLUTE FILTRATION RATING
Manufactures and users of hydraulic equipment admit that
contamination is the most likely cause of malfunction or
failure in hydraulic systems and reduces security and
reliability of components and systems. Metal particles
flowing throughout the circuit scratch moving surfaces so
that contaminaton level, if not controlled, increases very
rapidly.
It is strongly recommended to mantain contamination level
at least at nominal values shown below, choosing adequate
filtration products.
It’s the diameter X of the largest particle with BETAx • 75.
CONTAMINATION CLASS
It’s the ratio between the number of particles before and
after the filter with diameter larger than X micron.
ISO 4406:1999
It’s expressed by 3 scale numbers representing
respectively: the number of particles equal to or larger than
4 —m(c); the number of particles equal to or larger than 6
—m(c); the number of particles equal to or larger than 14
—m(c), contained in 0.034 oz (1 ml) of fluid.
CONTAMINATION CLASS
FILTRATION RATIO BETAx
ISO 4572
NAS 1638
It’s expressed by one scale numbers representing the
number of particles of different size ranges contained in 3.4
oz (100 ml) of fluid.
TYPE OF SYSTEM
MINIMUM
REQUIRED
TYPE OF VALVE
NOMINAL
FILTRATION
ABSOLUTE
FILTRATION
RATING
ISO 4572
(—m)
BETAx • 75
ISO 4406:1999
NAS 1638
6
X = 6…10
18 / 16 / 13
7
10
X = 10…12
19 / 17 / 14
8
15
X = 12…15
20 / 18 / 15
9
25
X = 15…25
21 / 19 / 16
10
PROPORTIONAL VALVES
FILTRATION RECOMMENDATIONS
FOR EXTENDED PRODUCT LIFE
CONTAMINATION
ACCORDING TO
Systems/components operating at
HIGH PRESSURE > 3600 psi (250 bar)
HIGH CYCLE APPLICATIONS
Sistems/components with LOW dirt
tolerance
Systems/components operating at
MEDIUM PRESSURE up to 3600 psi
(250 bar)
Systems/components operating at
LOW PRESSURE < 1450 psi (100 bar)
LOW CYCLE APPLICATIONS
Systems/components with GOOD
dirt tolerance.
Rev.06.05
7.01.050.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
Pressure Control Valves
VSBN-08A
VSPY-10A
VSBN-10A
VSPY-10A
VSBG-10A
VSPY-10A
VSNG-10A
VRPP-10A
VSPN-10A
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
RELIEF, DIRECT ACTING GUIDED
RELIEF,POPPET
DIRECTTYPE
ACTING GUIDED POPPET TYPE
COMMON CAVITY
COMMON CAVITY
VSBN-08A
SIZE 08
VSBN-08A
04.11.49 - XSIZE
- 56 08
-Z
04.11.49 - X - 56 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
5 gpm
(20 l/min)
Cavity : CA-08A-2N (see page CT.A.001.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.011
Flow is blocked from 1 to 2 until pressure increases to meet the selected valve
setting, lifting the poppet from its seat and allowing relief flow through port 2 to tank.
Pressure at port 2 is additive to the relief setting of the valve. The unique Oil Control
poppet design provides enhanced stability at all flows and pressures.
Installation torque :
25-30 ft-lb
(34-41 Nm)
Weight:
0.309 lbs
(0.140 Kg)
X
SPRINGS
Z
05
X = 03
10
20
35
X = 04 35
X = 73 35
Rev.0605
Adj. press.
range psi
(bar)
145-1000
(10-70)
500-2000
(35-140)
1500-3000
(105-210)
2500-5000
(175-350)
500-5000
(35-350)
500-5000
(35-350)
Press. increase Standard setting
psi / turn
psi (bar)
(bar/turn)
(Q=5 l/min)
375
725
(26)
(50)
725
1450
(50)
(100)
1145
2900
(79)
(200)
2465
5000
(170)
(350)
1044
2900
(72)
(200)
1044
2900
(72)
(200)
ADJUSTMENTS
03
Leakproof hex. socket screw
04
Handknob and locknut
73
O-Ring seal on adjust screw
OPTIONS
Ordering code
Description
X = 03 11.04.23.002
X = 73 11.04.23.004
Tamper resistant cap
Special settings available. Contact factory authorized
representative for ordering code.
Page. AA1.020
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
RELIEF, DIRECT ACTING GUIDED
RELIEF,POPPET
DIRECTTYPE
ACTING GUIDED POPPET TYPE
COMMON CAVITY
COMMON CAVITY
VSBN-10A
SIZE 10
VSBN-10A
04.11.55 - XSIZE
- 85 10
-Z
04.11.55 - X - 85 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
13 gpm
(50 l/min)
Cavity : CA-10A-2N (see page CT.A.001.U)
/LQHERGLHVVHHSDJH01$«
External seal kit : see page A11.011
Flow is blocked from 1 to 2 until pressure increases to meet the selected valve
setting, lifting the poppet from its seat and allowing relief flow through port 2 to tank.
Pressure at port 2 is additive to the relief setting of the valve. The unique Oil Control
poppet design provides enhanced stability at all flows and pressures.
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.430 lbs
(0.195 Kg)
X
03
SPRINGS
Z
Adj. press.
range psi
(bar)
Press. increase
psi / turn
(bar/turn)
Standard setting
psi (bar)
(Q=5 l/min)
05
75-1000
(5-70)
232
(16)
725
(50)
10
500-2000
(35-140)
348
(24)
1450
(100)
20
1500-3000
(105-210)
783
(54)
2900
(200)
35
2500-5000
(175-350)
1218
(84)
5000
(350)
Rev.0906
ADJUSTMENTS
Leakproof hex. socket screw
OPTIONS
Ordering code
Description
11.04.23.002
Tamper resistant cap
Special settings available. Contact factory authorized
representative for ordering code.
Page. AA1.030
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
RELIEF, DIRECT ACTING GUIDED
RELIEF,POPPET
DIRECTTYPE
ACTING GUIDED POPPET TYPE
COMMON CAVITY
COMMON CAVITY
VSBG-10A
SIZE 10
VSBG-10A
04.11.56 - XSIZE
- 85 10
-Z
04.11.56 - X - 85 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
13 gpm
(50 l/min)
Cavity : CA-10A-2N (see page CT.A.001.U)
/LQHERGLHVVHHSDJH01$«
External seal kit : see page A11.011
Flow is blocked from 2 to 1 until pressure increases to meet the selected valve
setting, lifting the poppet from its seat and allowing relief flow through port 1 to tank.
Pressure at port 1 is additive to the relief setting of the valve. The unique Oil Control
poppet design provides enhanced stability at all flows and pressures.
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.430 lbs
(0.195 Kg)
X
03
SPRINGS
Z
Adj. press.
range psi
(bar)
Press. increase
psi / turn
(bar/turn)
Standard setting
psi (bar)
(Q=5 l/min)
05
75-1000
(5-70)
232
(16)
725
(50)
10
500-2000
(35-140)
348
(24)
1450
(100)
20
1500-3000
(105-210)
783
(54)
2900
(200)
35
2500-5000
(175-350)
1218
(84)
5000
(350)
Rev.0906
ADJUSTMENTS
Leakproof hex. socket screw
OPTIONS
Ordering code
Description
11.04.23.002
Tamper resistant cap
Special settings available. Contact factory authorized
representative for ordering code.
Page. AA1.040
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
RELIEF, BI-DIRECTIONAL RELIEF, BI-DIRECTIONAL
DIRECT ACTING POPPET TYPE
DIFFERENTIAL
AREATYPE DIFFERENTIAL AREA
DIRECT
ACTING POPPET
COMMON CAVITY
COMMON CAVITY
VSNG-10A
SIZE 10
VSNG-10A
04.11.59 - XSIZE
- 85 10
-Z
04.11.59 - X - 85 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
15 gpm
(56 l/min)
Cavity : CA-10A-2N (see page CT.A.001.U)
/LQHERGLHVVHHSDJH01$«
External seal kit : see page A11.011
Flow is blocked bi-directionally between 1 and 2 until pressure at either port
increases to meet the selected valve setting, lifting the poppet from its seat and
allowing relief flow to the opposite port.
The unique Oil Control poppet design
provides consistent cracking pressures at both ports and enhanced stability at all
flows and pressures.
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.551 lbs
(0.250 Kg)
Maximum difference for crack pressure in both direction : 145 psi (10 bar)
X
03
ADJUSTMENTS
Leakproof hex. socket screw
SPRINGS
Z
Adj. press.
range psi
(bar)
Press. increase
psi / turn
(bar/turn)
Standard setting
psi (bar)
(Q=5 l/min)
10
450-1450
(30-100)
196
(13.5)
1450
(100)
20
1450-3000
(100-210)
450
(31)
2900
(200)
Rev.0706
Page. AA1.042
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
RELIEF, PILOT
PILOT OPERATED
OPERATED SPOOL
RELIEF,
SPOOL TYPE
TYPE
COMMON
CAVITY
COMMON CAVITY
VSPN-10A
VSPN-10A
SIZE 10
04.12.08
04.12.08 -- X
X -- 85
85 - Z
TECHNICAL DATA
Max. pressure:
6000 psi
(420 bar)
Max. flow:
32 gpm
(120 l/min)
Int. leakage ave. :
2900 psi
3
12 in /min
(200 bar)
3
(200 cm /min)
Cavity : CA-10A-2N (see page CT.A.001.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.011
Flow is blocked from 1 to 2 until pressure increases to meet the selected valve
setting, lifting the conical, pilot-stage poppet from its seat. This action exhausts oil
above the main-stage piston (spool type), allowing it to shift and provide relief flow
through 2 to tank. Pressure at 2 is additive to the relief setting of the valve.
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.463 lbs
(0.210 Kg)
X
ADJUSTMENTS
03
Leakproof hex. socket screw
04
Handknob and locknut
SPRINGS
Z
10
X = 03
20
35
X = 04 35
Rev.0605
Adj. press.
range psi
(bar)
500-2000
(35-140)
1000-4000
(70-280)
2000-6000
(140-420)
500-5000
(35-350)
Press. increase Standard setting
psi / turn
psi (bar)
(bar/turn)
(Q=5 l/min)
696
1450
(48)
(100)
1276
2900
(88)
(200)
2030
5000
(140)
(350)
986
(68)
5000
(350)
OPTIONS
Ordering code
Description
11.04.23.002
Tamper resistant cap
Special settings available. Contact factory authorized
representative for ordering code.
Page. AA1.050
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
RELIEF, PILOT OPERATED RELIEF,
SPOOL TYPE
PILOT OPERATED SPOOL TYPE
EXTERNAL DRAIN
EXTERNAL DRAIN
COMMON CAVITY
COMMON CAVITY
VSPY-10A
SIZE 10
VSPY-10A
04.13.05 - XSIZE
- 8510
-Z
04.13.05 - X - 85 - Z
TECHNICAL DATA
Max. pressure:
6000 psi
(420 bar)
Max. flow:
32 gpm
(120 l/min)
Int. leakage ave. :
2900 psi
3
12 in /min
(200 bar)
3
(200 cm /min)
Cavity : CA-10A-3N (see page CT.A.003.U)
/LQHERGLHVVHHSDJH01$«
External seal kit : see page A11.011
Flow is blocked from 1 to 2 until pressure increases to meet the selected valve
setting, lifting the conical, pilot-stage poppet from its seat. This action exhausts oil
above the main-stage piston (spool type), allowing it to shift and provide relief flow
through 2 to tank. The spring chamber is drained to tank at 3 allowing a consistent
relief setting independent of back-pressure at 2.
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.463 lbs
(0.210 Kg)
X
03
ADJUSTMENTS
Leakproof hex. socket screw
SPRINGS
Z
10
20
35
Adj. press.
range psi
(bar)
500-2000
(35-140)
1000-4000
(70-280)
2000-6000
(140-420)
Press. increase
psi / turn
(bar/turn)
696
(48)
1276
(88)
2030
(140)
Standard setting
psi (bar)
(Q=5 l/min)
1450
(100)
2900
(200)
5000
(350)
OPTIONS
Ordering code
Description
11.04.23.002
Tamper resistant cap
Special settings available. Contact factory authorized
representative for ordering code.
Rev.0607
Page. AA1.070
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
PRESSURE REDUCING,
REDUCING, PILOT
PILOT OPERATED
OPERATED SPOOL
SPOOL TYPE
TYPE
PRESSURE
COMMON
CAVITY
COMMON CAVITY
VRPP-10A
SIZE 10
04.93.06
04.93.06 -- X
X -- 85
85 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. regulated pressure: 4000 psi
(280 bar)
Max. flow:
(60 l/min)
16 gpm
Cavity : CA-10A-3N (see page CT.A.003.U)
/LQHERGLHVVHHSDJH01«
External seal kit : see page A11.011
Initially, flow passes freely from 2 to 1. When the pressure at 1 exceeds the pressure
setting, the valve acts to restrict input flow at 2. This increases the pressure drop
through the valve and maintains consistent pressure at 1. The spring chamber is
drained at 3 to prevent a build-up of back-pressure against the spool.
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.463 lbs
(0.210 Kg)
Std. internal orifice :
0.6 mm
X
03
ADJUSTMENTS
Leakproof hex. socket screw
SPRINGS
Z
10
20
Adj. press.
range psi
(bar)
145-2000
(10-140)
1000-4000
(70-280)
Press. increase
psi / turn
(bar/turn)
696
(48)
1276
(88)
Standard setting
psi
(bar)
1450
(100)
2900
(200)
OPTIONS
Ordering code
Description
11.04.23.002
Tamper resistant cap
Special settings available. Contact factory authorized
representative for ordering code.
Rev.0607
Page. AA2.010
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
PRESSURE REDUCING
REDUCING AND
AND RELIEVING,
RELIEVING,
PRESSURE
PILOT
OPERATED
SPOOL
TYPE
PILOT OPERATED SPOOL TYPE
COMMON CAVITY
CAVITY
COMMON
VRPX-10A
SIZE 10
04.93.07
04.93.07 -- X
X -- 85
85 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
16 gpm
(60 l/min)
Cavity : CA-10A-3N (see page CT.A.003.U)
/LQHERGLHVVHHSDJH01$«
External seal kit : see page A11.011
Initially, flow passes freely from 2 to 1. When the pressure at 1 exceeds the pressure
setting, the conical poppet in the upper, pilot stage is lifted from its seat. This allows
the main-stage piston to shift, restricting input flow at 2. This increases the pressure
drop through the valve and maintains consistent pressure at 1. The spring chamber
is drained at 3 to prevent a build-up of back-pressure against the spool. Additionally,
if pressure at 1 rises above the pressure setting, flow is relieved to 3 until the setting
is re-attained.
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.441 lbs
(0.200 Kg)
Std. internal orifice : 0.6 mm
X
03
ADJUSTMENTS
Leakproof hex. socket screw
SPRINGS
Z
10
20
Adj. press.
range psi
(bar)
500-2000
(35-140)
1000-4000
(70-280)
Press. increase
psi / turn
(bar/turn)
696
(48)
1276
(88)
Standard setting
psi (bar)
(reduc. mode)
1450
(100)
2900
(200)
OPTIONS
Ordering code
Description
11.04.23.002
Tamper resistant cap
Special settings available. Contact factory authorized
representative for ordering code.
Rev.0607
Page. AA2.040
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
PRESSURE REDUCING
REDUCING AND
AND RELIEVING,
RELIEVING,
PRESSURE
DIRECT
ACTING
SPOOL
TYPE
DIRECT ACTING SPOOL TYPE
COMMON CAVITY
CAVITY
COMMON
VRPR-10A
SIZE 10
04.95.04
04.95.04 -- X
X -- 85
85 - Z
TECHNICAL DATA
Max. pressure (*):
5000 psi
(350 bar)
Max. flow:
8 gpm
(30 l/min)
Int. leakage ave. :
3 in /min
3
3
(50 cm /min)
Cavity : CA-10A-3N (see page CT.A.003.U)
/LQHERGLHVVHHSDJH01$«
External seal kit : see page A11.011
Initially, flow passes freely from 2 to 1. When the pressure at 1 exceeds the pressure
setting, the valve acts to restrict input flow at 2. This increases the pressure drop
through the valve and maintains consistent pressure at 1. The spring chamber is
drained at 3 to prevent a build-up of back-pressure against the spool. Additionally, if
pressure at 1 rises above the pressure setting, flow is relieved to 3 until the setting is
re-attained.
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.573 lbs
(0.260 Kg)
(*) Max pressure for
3000 psi
Z=01 version
X
ADJUSTMENTS
03
Leakproof hex. socket screw
04
Handknob and locknut
SPRINGS
Z
01
02
04
08
Adj. press.
range psi
(bar)
30-200
(2-14)
30-350
(2-25)
145-725
(10-50)
400-1160
(28-80)
Press. increase
psi / turn
(bar/turn)
29
(2)
44
(3)
102
(7)
203
(14)
Standard setting
psi (bar)
(reduc. mode)
115-145
(8-10)
100-145
(7-10)
500-580
(35-40)
650-725
(45-50)
(210 bar)
OPTIONS
Ordering code
Description
11.04.23.004
Tamper resistant cap
Special settings available. Contact factory authorized
representative for ordering code.
Rev.0906
Page. AA2.030
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
Special Valves
VPN1
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
CHECK, HOSE BURST
CHECK, HOSE BURST
VPN1
VPN1
0T.F4.01 - X - Y - Z
0T.F4.01 - X - Y - Z
TECHNICAL DATA
Max. pressure:
4500 psi
(315 bar)
Flow: see below graphs (‘R’-Q)
When the lowering speed exceeds preset value, as it might happen in case of hose
failure, the flow is blocked. These valves should ideally be screwed directly into the
actuator outlet port. Sealing parts are superfinished and enable to lock the load in the
position where the actuator is in the moment of hose failure. These valves can be
supplied, on request, with an orifice on the disc, allowing an emergency lowering of
the load. It is recommended to fit a flow regulator valve downstream the hose burst
valve, at the end of the flexible hose, to control the lowering speed at the nominal
value. The “R” gap must be adjusted to allow a flow at least 50% over the nominal
regulated flow from the actuator.
Special flow settings available. Please contact factory
authorized representative for ordering code.
Note: on request are available as “in line mounted sleeves
type configuration”. Please contact factory for any
information.
The valve is only supposed to be operated in case of
hose failure. Should this circumstance occur, we
strongly recommend to verify the integrity of the valve
and eventually to replace it in the event that the
pressure spike generated by the hose failure was such
to damage permanently some valve components.
X
ADJUSTMENTS
03
Locking nut + counter nut
see graphs (‘R’ - Q)
Y
PORTS
09
02
03
04
G 1/4
G 3/8
G 1/2
G 3/4
Z
00
01
02
03
04
05
ORIFICE DIAMETER (mm)
1
06
1.2
07
1.3
08
1.5
09
1.9
10
2
11
no orifice
0.5
0.6
0.7
0.8
0.9
FITTING TOOL DIMENSION
Rev.0905
Page. AT9.020
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
Check Valves
VUH1
VSON-08A
VSON-10A
VSON-12A
VSON-16A
VUCN-08A
VUCN-10A
VUCN-12A
VUCN-16A
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
CHECK, POPPET
POPPET TYPE
TYPE
CHECK,
VUH1
VUH1
0T.U5.01.00 --YY--ZZ
0T.U5.01.00
TECHNICAL DATA
Max. pressure:
5000 psi
Max. flow :
see diagram
(350 bar)
Note : valves are burnished.
When pressure at 1 rises above the spring bias pressure, the poppet is lifted and flow
allowed from 1 to 2. The valve is closed (checked) from 2 to 1. Precision machining
and hardening processes allow virtually leak-free performance in the checked
condition.
FITTING TOOL DIMENSION
Z
Cracking pressure
psi (bar)
Y
PORTS
00
< 7 (< 0.5)
09
G 1/4
02
G 3/8
03
G 1/2
Rev.0905
Page. AT4.050
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
PILOT OPERATED CHECK,PILOT
PILOTOPERATED
TO OPEN CHECK, PILOT TO OPEN
COMMON CAVITY
COMMON CAVITY
VSON-08A
SIZE 08
VSON-08A
04.33.06 - XSIZE
- 5608
-Z
04.33.06 - X - 56 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
8 gpm
(30 l/min)
Pilot ratio :
3:1
Cavity : CA-08A-3C (see page CT.A.002.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.011
When pressure at 2 rises above the spring bias pressure, the poppet is pushed from
its seat and flow is allowed from 2 to 1. The valve is normally closed (checked) from
1 to 2. When sufficient pilot pressure is present at port 3, the pilot piston acts to push
the poppet from its seat and flow is allowed from 1 to 2. Precision machining and
hardening processes allow virtually leak-free performance in the checked condition.
Installation torque :
25-30 ft-lb
(34-41 Nm)
Weight:
0.265 lbs
(0.120 Kg)
X
O-RING ON PILOT PISTON
00
No O-Ring
10
With O-Ring
SPRINGS
Z
00
Rev.0605
Cracking pressure
psi
(bar)
30
(2)
Page. AA4.070
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
PILOT OPERATED
OPERATED CHECK,
CHECK, PILOT
PILOT TO
TO OPEN
OPEN
PILOT
COMMON
CAVITY
COMMON CAVITY
VSON-10A
VSON-10A
SIZE 10
04.33.05
04.33.05 -- X
X -- 85
85 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
16 gpm
(60 l/min)
Pilot ratio :
3.2 : 1
Cavity : CA-10A-3C (see page CT.A.002.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.011
When pressure at 2 rises above the spring bias pressure, the poppet is pushed from
its seat and flow is allowed from 2 to 1. The valve is normally closed (checked) from
1 to 2. When sufficient pilot pressure is present at port 3, the pilot piston acts to push
the poppet from its seat and flow is allowed from 1 to 2. Precision machining and
hardening processes allow virtually leak-free performance in the checked condition.
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.265 lbs
(0.120 Kg)
X
O-RING ON PILOT PISTON
00
No O-Ring
10
With O-Ring
SPRINGS
Z
00
Rev.0605
Cracking pressure
psi
(bar)
30
(2)
Page. AA4.080
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
PILOT OPERATED CHECK,PILOT
PILOTOPERATED
TO OPEN CHECK, PILOT TO OPEN
COMMON CAVITY
COMMON CAVITY
VSON-12A
SIZE 12
VSON-12A
04.33.07 - XSIZE
- 5712
-Z
04.33.07 - X - 57 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
32 gpm
(120 l/min)
Pilot ratio :
3.2 : 1
Cavity : CA-12A-3C (see page CT.A.002.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.011
When pressure at 2 rises above the spring bias pressure, the poppet is pushed from
its seat and flow is allowed from 2 to 1. The valve is normally closed (checked) from
1 to 2. When sufficient pilot pressure is present at port 3, the pilot piston acts to push
the poppet from its seat and flow is allowed from 1 to 2. Precision machining and
hardening processes allow virtually leak-free performance in the checked condition.
Installation torque :
60-70 ft-lb
(81-95 Nm)
Weight:
0.551 lbs
(0.250 Kg)
X
O-RING ON PILOT PISTON
00
No O-Ring
10
With O-Ring
SPRINGS
Z
00
Rev.0605
Cracking pressure
psi
(bar)
30
(2)
Page. AA4.090
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
PILOT OPERATED
OPERATED CHECK,
CHECK, PILOT
PILOT TO
TO OPEN
OPEN
PILOT
COMMON
CAVITY
COMMON CAVITY
VSON-16A
VSON-16A
SIZE 16
04.33.08
04.33.08 -- X
X -- 27
27 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
53 gpm
(200 l/min)
Pilot ratio :
3:1
Cavity : CA-16A-3C (see page CT.A.002.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.012
When pressure at 2 rises above the spring bias pressure, the poppet is pushed from
its seat and flow is allowed from 2 to 1. The valve is normally closed (checked) from
1 to 2. When sufficient pilot pressure is present at port 3, the pilot piston acts to push
the poppet from its seat and flow is allowed from 1 to 2. Precision machining and
hardening processes allow virtually leak-free performance in the checked condition.
Installation torque :
80-90 ft-lb
(108-122 Nm)
Weight:
0.706 lbs
(0.320 Kg)
X
O-RING ON PILOT PISTON
00
No O-Ring
10
With O-Ring
SPRINGS
Z
00
Rev.0605
Cracking pressure
psi
(bar)
22
(1.5)
Page. AA4.100
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
CHECK, POPPET TYPE
COMMON CAVITY
CHECK, POPPET TYPE
COMMON CAVITY
VUCN-08A
SIZE 08
VUCN-08A
04.31.20.00.56
Z
SIZE -08
04.31.20.00.56 - Z
TECHNICAL DATA
Max. pressure:
6000 psi
(420 bar)
Max. flow:
13 gpm
(50 l/min)
Cavity : CA-08A-2N (see page CT.A.001.U)
/LQHERGLHVVHHSDJH01$«
External seal kit : see page A11.011
When pressure at 1 rises above the spring bias pressure, the poppet is lifted and flow
allowed from 1 to 2. The valve is closed (checked) from 2 to 1. Precision machining
and hardening processes allow virtually leak-free performance in the checked
condition.
Installation torque :
25-30 ft-lb
(34-41 Nm)
Weight:
0.265 lbs
(0.120 Kg)
SPRINGS
Z
00
03
05
14
Rev.0605
Cracking pressure
psi
(bar)
15
(1)
39
(2.7)
75
(5)
200
(14)
Page AA4.010
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
CHECK, POPPET TYPE
COMMON CAVITY
CHECK, POPPET TYPE
COMMON CAVITY
VUCN-10A
SIZE 10
VUCN-10A
04.31.23.00.85
Z
SIZE -10
04.31.23.00.85 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
21 gpm
(80 l/min)
Cavity : CA-10A-2N (see page CT.A.001.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.011
When pressure at 1 rises above the spring bias pressure, the poppet is lifted and flow
allowed from 1 to 2. The valve is closed (checked) from 2 to 1. Precision machining
and hardening processes allow virtually leak-free performance in the checked
condition.
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.331 lbs
(0.150 Kg)
SPRINGS
Z
00
05
15
Rev.0605
Cracking pressure
psi
(bar)
7
(0.5)
75
(5)
220
(15)
Page. AA4.020
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
CHECK, POPPET
POPPET TYPE
TYPE
CHECK,
COMMON
CAVITY
COMMON CAVITY
VUCN-12A
VUCN-12A
SIZE 12
04.31.28.00.57
04.31.28.00.57 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
32 gpm
(120 l/min)
Cavity : CA-12A-2N (see page CT.A.001.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.011
When pressure at 1 rises above the spring bias pressure, the poppet is lifted and flow
allowed from 1 to 2. The valve is closed (checked) from 2 to 1. Precision machining
and hardening processes allow virtually leak-free performance in the checked
condition.
Installation torque :
60-70 ft-lb
(81-95 Nm)
Weight:
0.397 lbs
(0.180 Kg)
SPRINGS
Z
00
05
15
Rev.0605
Cracking pressure
psi
(bar)
15
(1)
75
(5)
220
(15)
Page. AA4.030
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
CHECK, POPPET TYPE
COMMON CAVITY
CHECK, POPPET TYPE
COMMON CAVITY
VUCN-16A
SIZE 16
VUCN-16A
04.31.25.00.27
Z
SIZE -16
04.31.25.00.27 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
53 gpm
(200 l/min)
Cavity : CA-16A-2N (see page CT.A.001.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.012
When pressure at 1 rises above the spring bias pressure, the poppet is lifted and flow
allowed from 1 to 2. The valve is closed (checked) from 2 to 1. Precision machining
and hardening processes allow virtually leak-free performance in the checked
condition.
Installation torque :
80-90 ft-lb
(108-122 Nm)
Weight:
0.595 lbs
(0.270 Kg)
SPRINGS
Z
00
02
Rev.0605
Cracking pressure
psi
(bar)
15
(1)
30
(2)
Page. AA4.040
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
Counterbalance Valves
VBSN-08AA
VBSN-10A
VBSN-12A
VBSN-16A
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
COUNTERBALANCE, STANDARD
GUIDED POPPET
TYPE
COUNTERBALANCE,
STANDARD
GUIDED POPPET TYPE
COMMON CAVITY
COMMON CAVITY
VBSN-08AA
SIZE 08
04.52.20 - XSIZE
- 56 08
-Z
VBSN-08AA
04.52.20 - X - 56 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
8 gpm
(30 l/min)
Cavity : CA-08A-3C (see page A10.011)
/LQHERGLHVVHHSDJH$±$
External seal kit : see page A11.011
When pressure at 2 rises above the spring bias pressure, the check seat is pushed
away from the piston and flow is allowed from 2 to 1. When load pressure at 1 rises
above the pressure setting, the direct-acting, relief function is activated and flow is
relieved from 1 to 2. With pilot pressure at 3, the pressure setting is reduced in
proportion to the stated ratio of the valve, until fully open with free-flow from 1 to 2.
The spring chamber is drained to 2, and any back-pressure at 2 is additive to the
pressure setting in all functions.
Installation torque :
25-30 ft-lb
(34-41 Nm)
Weight:
0.397 lbs
(0.180 Kg)
Pressure setting: at least 1.3 times the load induced
pressure.
X
PILOT RATIO
03
4:1
33
4:1
SPRINGS
Z
15
20
35
Adj. press.
range psi
(bar)
1000-2200
(70-150)
1450-3000
(100-210)
2900-5000
(200-350)
Press. increase
psi / turn
(bar/turn)
1051
(72.5)
1581
(109)
1987
(137)
Standard setting
psi (bar)
(Q=5 l/min)
2200
(150)
2900
(200)
5000
(350)
With sealed pilot
OPTIONS
Ordering code
Ordering code
Description
03.51.01.329
03.51.01.328
03.51.01.327
11.04.23.002
Tamper resistant cap
Special settings available. Contact factory authorized
representative for ordering code.
Rev.0306
Page AA5.010
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
COUNTERBALANCE, STANDARD
STANDARD POPPET
POPPET TYPE
TYPE
COUNTERBALANCE,
DIFFERENTIAL
AREA
DIFFERENTIAL AREA
COMMON CAVITY
CAVITY
COMMON
VBSN-10A
VBSN-10A
SIZE 10
04.52.31
04.52.31 -- X
X -- 85
85 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
16 gpm
(60 l/min)
Cavity : CA-10A-3C (see page CT.A.002.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.011
When pressure at 2 rises above the spring bias pressure, the check seat is pushed
away from the piston and flow is allowed from 2 to 1. When load pressure at 1 rises
above the pressure setting, the direct-acting, differential area relief function is
activated and flow is relieved from 1 to 2. With pilot pressure at 3, the pressure
setting is reduced in proportion to the stated ratio of the valve, until fully open with
free-flow from 1 to 2. The spring chamber is drained to 2, and any back-pressure at
2 is additive to the pressure setting in all functions.
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.441 lbs
(0.200 Kg)
Pressure setting: at least 1.3 times the load induced
pressure
X
PILOT RATIO
03
3:1
10
8:1
SPRINGS
Z
X = 03
X = 10
20
35
20
35
Adj. press.
range psi
(bar)
1000-3000
(70-210)
2000-5000
(140-350)
1000-3000
(70-210)
2000-5000
(140-350)
Press. increase
psi / turn
(bar/turn)
1958
(135)
2842
(196)
754
(52)
1291
(89)
Standard setting
psi (bar)
(Q=5 l/min)
2900
(200)
5000
(350)
2900
(200)
5000
(350)
OPTIONS
Ordering code
Description
11.04.23.002
Tamper resistant cap
Special settings available. Contact factory authorized
representative for ordering code.
Rev.0605
Page. AA5.030
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
COUNTERBALANCE, STANDARD
POPPET TYPESTANDARD POPPET TYPE
COUNTERBALANCE,
DIFFERENTIAL AREA
DIFFERENTIAL AREA
COMMON CAVITY
COMMON CAVITY
VBSN-12A
SIZE 12
VBSN-12A
04.52.28 - XSIZE
- 5712
-Z
04.52.28 - X - 57 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
32 gpm
(120 l/min)
Cavity : CA-12A-3C (see page CT.A.002.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.011
When pressure at 2 rises above the spring bias pressure, the check seat is pushed
away from the piston and flow is allowed from 2 to 1. When load pressure at 1 rises
above the pressure setting, the direct-acting, differential area relief function is
activated and flow is relieved from 1 to 2. With pilot pressure at 3, the pressure
setting is reduced in proportion to the stated ratio of the valve, until fully open with
free-flow from 1 to 2. The spring chamber is drained to 2, and any back-pressure at
2 is additive to the pressure setting in all functions.
Installation torque :
60-70 ft-lb
(81-95 Nm)
Weight:
0.860 lbs
(0.390 Kg)
Pressure setting: at least 1.3 times the load induced
pressure
X
PILOT RATIO
03
4:1
10
8:1
SPRINGS
Z
X = 03
X = 10
20
35
20
35
Adj. press.
range psi
(bar)
1000-3000
(70-210)
2000-5000
(140-350)
1000-3000
(70-210)
2000-5000
(140-350)
Press. increase
psi / turn
(bar/turn)
725
(50)
2306
(159)
609
(42)
972
(67)
Standard setting
psi (bar)
(Q=5 l/min)
2900
(200)
5000
(350)
2900
(200)
5000
(350)
OPTIONS
Ordering code
Description
11.04.23.002
Tamper resistant cap
Special settings available. Contact factory authorized
representative for ordering code.
Rev.0605
Page. AA5.040
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
COUNTERBALANCE, STANDARD
STANDARD POPPET
POPPET TYPE
TYPE
COUNTERBALANCE,
DIFFERENTIAL
AREA
DIFFERENTIAL AREA
COMMON CAVITY
CAVITY
COMMON
VBSN-16A
VBSN-16A
SIZE 16
04.52.29
04.52.29 -- X
X -- 27
27 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
53 gpm
(200 l/min)
Cavity : CA-16A-3C (see page CT.A.002.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.012
When pressure at 2 rises above the spring bias pressure, the check seat is pushed
away from the piston and flow is allowed from 2 to 1. When load pressure at 1 rises
above the pressure setting, the direct-acting, differential area relief function is
activated and flow is relieved from 1 to 2. With pilot pressure at 3, the pressure
setting is reduced in proportion to the stated ratio of the valve, until fully open with
free-flow from 1 to 2. The spring chamber is drained to 2, and any back-pressure at
2 is additive to the pressure setting in all functions.
Installation torque :
80-90 ft-lb
(108-122 Nm)
Weight:
1.808 lbs
(0.820 Kg)
Pressure setting: at least 1.3 times the load induced
pressure
X
PILOT RATIO
03
4:1
10
8:1
SPRINGS
Z
X = 03
20
35
X = 10 40
Adj. press.
range psi
(bar)
1000-3000
(70-210)
2000-5000
(140-350)
2000-6000
(140-420)
Press. increase
psi / turn
(bar/turn)
1015
(70)
1566
(108)
1958
(135)
Standard setting
psi (bar)
(Q=5 l/min)
2900
(200)
5000
(350)
5000
(350)
OPTIONS
Ordering code
Description
11.04.23.004
Tamper resistant cap
Special settings available. Contact factory authorized
representative for ordering code.
Rev.0605
Page. AA5.050
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
Flow Control Valves
STVU-08A
VRFB-10A
VRFD-10
DRFN-10A
ST-C-06
ST-C-10A
ST-C-12A
ST-C-16A
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
NEEDLE RESTRICTOR,
RESTRICTOR, FREE
FREE REVERSE
REVERSE FLOW
FLOW
NEEDLE
COMMON
CAVITY
COMMON CAVITY
STVU-08A
STVU-08A
SIZE 08
04.01.02
04.01.02 -- X
X -- 56.00
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
11 gpm
(40 l/min)
Cavity : CA-08A-2N (see page CT.A.001.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.011
With flow from 2 to 1, the valve provides a fully adjustable orifice restriction. Free
flow is permitted from 1 to 2, regardless of valve adjustment, by when pressure
overcomes the spring bias of the valve’s check function.
Installation torque :
25-30 ft-lb
(34-41 Nm)
Weight:
0.353 lbs
(0.160 Kg)
X
Rev.0605
ADJUSTMENTS
03
Leakproof hex. socket screw
04
Handknob and locknut
Page. AA7.010
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
FLOW CONTROL, 2-WAY PRESSURE
COMPENSATED
FLOW CONTROL,
2-WAY PRESSURE COMPENSATED
FULLY ADJUSTABLE
FULLY ADJUSTABLE
COMMON CAVITY
COMMON CAVITY
VRFB-10A
SIZE 10
VRFB-10A
04.02.02 - XSIZE
- 8510
-Z
04.02.02 - X - 85 - Z
TECHNICAL DATA
Pressure min-max:
200-5000 psi
(14-350 bar)
Flow range: see below
Cavity : CA-10A-2N (see page CT.A.001.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.011
A constant flow rate, regardless of system pressures, is established from 1 to 2 while
a minimum pressure differential of 200 psi exists between the two ports. Output flow
can be varied from closed to the nominal maximum rating for the valve. Flow from 2
to 1 is limited by the diameter of the selected control orifice and is not pressure
compensated.
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.595 lbs
(0.270 Kg)
X
ADJUSTMENTS
40 Calibrated handknob
04 Handknob
Z
REGULATED FLOW RANGE
20 0.01-5.28
40 0.03-7.93
Rev.0605
gpm
0.05-20
l/min
gpm
0.10-30
l/min
Page. AA7.040
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
FLOW CONTROL, 3-WAY PRESSURE
COMPENSATED
FLOW CONTROL,
3-WAY PRESSURE COMPENSATED
COMBINATION TYPE FULLY
ADJUSTABLE
COMBINATION TYPE FULLY ADJUSTABLE
COMMON CAVITY
COMMON CAVITY
VRFD-10A
SIZE 10
VRFD-10A
04.04.02 - XSIZE
- 8510
-Z
04.04.02 - X - 85 - Z
TECHNICAL DATA
Pressure min-max:
200-5000 psi
(14-350 bar)
Max inlet flow:
16 gpm
(60 l/min)
Flow range: see below
Cavity : CA-10A-3N (see page CT.A.003.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.011
A constant flow rate, regardless of system pressures, is established from 1 to 3 while
a minimum pressure differential of 200 psi exists between the two ports. Input flow
supplied to 1 in excess of the regulated output at 3 is by-passed to 2. Output flow
can be varied from closed to the nominal maximum rating for the valve. Flow from 3
to 1 is limited by the diameter of the selected control orifice and is not pressure
compensated. Flow from 2 to 1 is not permitted.
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.573 lbs
(0.260 Kg)
X
ADJUSTMENTS
40 Calibrated handknob
04 Handknob
Z
REGULATED FLOW RANGE
20 0.01-5.28
40 0.03-7.93
Rev.0605
gpm
0.05-20
l/min
gpm
0.10-30
l/min
Page. AA7.060
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
FLOW DIVIDER
DIVIDER AND
AND COMBINER
COMBINER
FLOW
COMMON
CAVITY
COMMON CAVITY
DRFN-10A
DRFN-10A
SIZE 10
04.05.01.00.85
04.05.01.00.85 - Z
TECHNICAL DATA
Pressure min-max:
145-5000 psi
(10-350 bar)
Range of rated total flow: see table Z
Division or combination ratio: 50%-50%
Cavity : CA-10A-4N (see page CT.A.004.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.011
Input flow at 3 will be divided and output equally to 2 and 4 independent of system
pressures. Flow input at 2 and 4 will be combined and output at 3. Should either 2
or 4 become blocked in flow division mode, approximately 5% of the input flow will be
transmitted to the open port.
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.617 lbs
(0.280 Kg)
Slippage (tolerance) from theoretical divided flows:
±5% to ±10%, depending from inlet flow (see diagram).
N.B.: slippage is lowest toward upper limit of nominal range.
Z
02
04
08
16
25
30
40
Rev.0605
RANGE OF TOTAL FLOW
0.26-0.79
gpm
1-3
l/min
0.53-1.59
1.32-3.44
gpm
2-6
l/min
gpm
5-13
l/min
2.38-6.34
gpm
9-24
l/min
3.70-9.78
gpm
14-37
l/min
4.23-11.63
gpm
16-44
l/min
5.28-14.27
gpm
20-54
l/min
Page. AA7.090
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
FLOW CONTROL VALVES FLOW CONTROL VALVES
CARTRIDGE RESTRICTORS
CARTRIDGE RESTRICTORS
COMMON CAVITY
COMMON CAVITY
ST-C-06
ST-C-06
SIZE 08
OD.21.01 SIZE
- X - 56
08
OD.21.01 - X - 56
Hex. .94 / 28.8-37.6 ft-lb
Hex. (24) / (39-51) Nm
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Rated Flow
11 gpm
(40 l/min)
Cavity - Tooling (CA-08A-2N)
page CT.A.001.U
Line bodies
page MN2.A…
Weight
0.199 lbs (0.090 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 Pm nominal or
better
page 7.01.050
Adjustment Torque
at 145 psi (10 bar)
0.7 ft-lb
(1 Nm)
Adjustment Torque
at 5000 psi (350 bar)
3.7 ft-lb
(5 Nm)
Mounting Position
X
unrestricted
ORDERING OPTIONS
03 Socket Screw
04 Handknob and Locknut
Rev.06.05
3.11.010.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
FLOW CONTROL
CONTROL VALVES
VALVES
FLOW
CARTRIDGE
RESTRICTORS
CARTRIDGE RESTRICTORS
COMMON CAVITY
CAVITY
COMMON
ST-C-10A
ST-C-10A
SIZE 10
OD.21.01
OD.21.01 -- XX -- 36
36
Hex. 1.06 / 32.5-41.3 ft-lb
Hex. (27) / (44-56) Nm
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Rated Flow
19 gpm
(70 l/min)
Cavity - Tooling (CA-10A-2N)
page CT.A.001.U
Line bodies
page MN1.A…
Weight
0.397 lbs (0.180 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 Pm nominal or
better
page 7.01.050
Adjustment Torque
at 145 psi (10 bar)
0.7 ft-lb
(1 Nm)
Adjustment Torque
at 5000 psi (350 bar)
7.4 ft-lb
(10 Nm)
Mounting Position
X
unrestricted
ORDERING OPTIONS
03 Socket Screw
04 Handknob and Locknut
Rev.06.05
3.15.020.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
FLOW CONTROL VALVES FLOW CONTROL VALVES
CARTRIDGE RESTRICTORS
CARTRIDGE RESTRICTORS
COMMON CAVITY
COMMON CAVITY
ST-C-12A
ST-C-12A
SIZE 12
OD.21.01 SIZE
- X - 89
12
OD.21.01 - X - 89
Hex. 1.26 / 39.8-48.7 ft-lb
Hex. (32) / (54-66) Nm
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Rated Flow
39 gpm
(150 l/min)
Cavity - Tooling (CA-12A-2N)
page CT.A.001.U
Line bodies
page MN1.A…
Weight
0.684 lbs (0.310 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 Pm nominal or
better
page 7.01.050
Adjustment Torque
at 145 psi (10 bar)
0.7 ft-lb
(1 Nm)
Adjustment Torque
at 5000 psi (350 bar)
13.3 ft-lb
(18 Nm)
Mounting Position
X
unrestricted
ORDERING OPTIONS
03 Socket Screw
04 Handknob and Locknut
Rev.06.05
3.15.030.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
CHECK, POPPET TYPE
COMMON CAVITY
CHECK, POPPET TYPE
COMMON CAVITY
VUCN-16A
SIZE 16
VUCN-16A
04.31.25.00.27
Z
SIZE -16
04.31.25.00.27 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
53 gpm
(200 l/min)
Cavity : CA-16A-2N (see page CT.A.001.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.012
When pressure at 1 rises above the spring bias pressure, the poppet is lifted and flow
allowed from 1 to 2. The valve is closed (checked) from 2 to 1. Precision machining
and hardening processes allow virtually leak-free performance in the checked
condition.
Installation torque :
80-90 ft-lb
(108-122 Nm)
Weight:
0.595 lbs
(0.270 Kg)
SPRINGS
Z
00
02
Rev.0605
Cracking pressure
psi
(bar)
15
(1)
30
(2)
Page. AA4.040
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
Logic Elements
VLST-10A
VLST-16A
VLST-20A
VLSP-10A
VLSP-16A
VCSQ-16A
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
LOGIC ELEMENT,
ELEMENT, FLOW
FLOW AND
CONTROL
LOGIC
AND PRESSURE
PRESSURE CONTROL
WITH
EXTERNAL
PILOT
WITH EXTERNAL PILOT
COMMON CAVITY
CAVITY
COMMON
VLST-10A
SIZE 10
04.84.01
04.84.01 -- X
X -- 85
85 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
16 gpm
(60 l/min)
Int. leakage ave. :
2900 psi
3
12 in /min
(200 bar)
3
(200 cm /min)
Cavity : CA-10A-3C (see page CT.A.002.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.011
When pressure at 1 rises above the selected spring bias pressure against the spool,
the valve shifts to allow flow from 1 to 2. Pilot pressure at 3 is additive to the spring
bias pressure. The valve may be used in switching or compensation type
applications.
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.265 lbs
(0.120 Kg)
X
ADJUSTMENTS
00
Fixed setting
03
Leakproof hex. socket screw
SPRINGS
Z
X = 00
04
08
X = 03 00
Rev.0605
Cracking press. Press. increase Standard setting
psi
psi
psi / turn
(bar)
(bar)
(bar/turn)
60 ±20%
(4 ±20%)
115 ±15%
(8 ±15%)
30-115
15
60
(2-8)
(1)
(4)
Page. AA8.010
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
LOGIC ELEMENT, FLOW AND
PRESSURE
CONTROL
LOGIC
ELEMENT,
FLOW AND PRESSURE CONTROL
WITH EXTERNAL PILOT WITH EXTERNAL PILOT
COMMON CAVITY
COMMON CAVITY
VLST-16A
VLST-16A
SIZE 16
04.84.01 - XSIZE
- 27 16
-Z
04.84.01 - X - 27 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
53 gpm
(200 l/min)
Int. leakage ave. :
2900 psi
3
12 in /min
(200 bar)
3
(200 cm /min)
Cavity : CA-16A-3C (see page CT.A.002.U)
/LQHERGLHVVHHSDJH01$«
External seal kit : see page A11.012
When pressure at 1 rises above the selected spring bias pressure against the spool,
the valve shifts to allow flow from 1 to 2. Pilot pressure at 3 is additive to the spring
bias pressure. The valve may be used in switching or compensation type
applications.
Installation torque :
80-90 ft-lb
(108-122 Nm)
Weight:
0.772 lbs
(0.350 Kg)
X
ADJUSTMENTS
00
Fixed setting
03
Leakproof hex. socket screw
SPRINGS
Z
04
X = 00
08
12
15
X = 03 00
Rev.0607
Cracking press. Press. increase Standard setting
psi
psi
psi / turn
(bar)
(bar)
(bar/turn)
60 ±20%
(4 ±20%)
123 ±15%
(8.5 ±15%)
175 ±10%
(12 ±10%)
218 ±10%
(15 ±10%)
60
60-175
22
(4)
(4-12)
(1.5)
Page. AA8.020
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
LOGIC ELEMENT,
ELEMENT, FLOW
FLOW AND
CONTROL
LOGIC
AND PRESSURE
PRESSURE CONTROL
WITH
EXTERNAL
PILOT
WITH EXTERNAL PILOT
COMMON CAVITY
CAVITY
COMMON
VLST-20A
SIZE 20
04.84.01
04.84.01 -- X
X -- 58
58 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
95 gpm
(360 l/min)
Int. leakage ave. :
2900 psi
3
12 in /min
(200 bar)
3
(200 cm /min)
Cavity : CA-20A-3C (see page CT.A.002.U)
Line bodies : see page MN1.A…
External seal kit : see page A11.012
When pressure at 1 rises above the selected spring bias pressure against the spool,
the valve shifts to allow flow from 1 to 2. Pilot pressure at 3 is additive to the spring
bias pressure. The valve may be used in switching or compensation type
applications.
Installation torque :
95-110 ft-lb
(128-149 Nm)
Weight:
1.764 lbs
(0.800 Kg)
X
00
ADJUSTMENTS
Fixed setting
SPRINGS
Z
05
11
Rev.0605
Cracking press.
psi
(bar)
80
(5.5)
167
(11.5)
Page. AA8.030
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
LOGIC ELEMENT, FLOW AND
PRESSURE
CONTROL
LOGIC
ELEMENT,
FLOW AND PRESSURE CONTROL
WITH INTERNAL PILOT
WITH INTERNAL PILOT
COMMON CAVITY
COMMON CAVITY
VLSP-10A
SIZE 10
VLSP-10A
04.84.03 - XSIZE
- 8510
-Z
04.84.03 - X - 85 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
16 gpm
(60 l/min)
Int. leakage ave. :
2900 psi
3
12 in /min
(200 bar)
3
(200 cm /min)
Cavity : CA-10A-3C (see page CT.A.002.U)
/LQHERGLHVVHHSDJH01$«
External seal kit : see page A11.011
When pressure at 1 rises above the selected spring bias pressure against the spool,
the valve shifts to allow flow from 1 to 2. The differential pressure between 1 and 3,
across an internal orifice, is additive to the spring bias pressure. Note that flow,
restricted by the internal orifice, can be transmitted from 3 to 1. The valve may be
used in switching or compensation type applications.
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.265 lbs
(0.120 Kg)
Standard internal
orifice:
0.6 mm
X
ADJUSTMENTS
00
Fixed setting
03
Leakproof hex. socket screw
SPRINGS
Z
X = 00
04
08
X = 03 00
Rev.0606
Cracking press. Press. increase Standard setting
psi
psi
psi / turn
(bar)
(bar)
(bar/turn)
60 ±20%
(4 ±20%)
115 ±15%
(8 ±15%)
30-115
15
60
(2-8)
(1)
(4)
Page. AA8.040
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
LOGIC ELEMENT,
ELEMENT, FLOW
FLOW AND
LOGIC
AND PRESSURE
PRESSURE CONTROL
CONTROL
WITH
INTERNAL
PILOT
WITH INTERNAL PILOT
COMMON CAVITY
CAVITY
COMMON
VLSP-16A
SIZE 16
04.84.03
04.84.03 -- X
X -- 27
27 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
53 gpm
(200 l/min)
Int. leakage ave. :
2900 psi
3
12 in /min
(200 bar)
3
(200 cm /min)
Cavity : CA-16A-3C (see page CT.A.002.U)
/LQHERGLHVVHHSDJH01$«
External seal kit : see page A11.012
When pressure at 1 rises above the selected spring bias pressure against the spool,
the valve shifts to allow flow from 1 to 2. The differential pressure between 1 and 3,
across an internal orifice, is additive to the spring bias pressure. Note that flow,
restricted by the internal orifice, can be transmitted from 3 to 1. The valve may be
used in switching or compensation type applications.
Installation torque :
80-90 ft-lb
(108-122 Nm)
Weight:
0.772 lbs
(0.350 Kg)
Standard internal
orifice:
0.6 mm
X
ADJUSTMENTS
00
Fixed setting
03
Leakproof hex. socket screw
SPRINGS
Z
04
X = 00 08
12
X = 03 00
Rev.0606
Cracking press. Press. increase Standard setting
psi
psi
psi / turn
(bar)
(bar)
(bar/turn)
60 ±20%
(4 ±20%)
115 ±15%
(8 ±15%)
175 ±10%
(12 ±10%)
60
60-175
22
(4)
(4-12)
(1.5)
Page. AA8.050
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
LOGIC ELEMENT, PRESSURE
COMPENSATOR
LOGIC
ELEMENT, PRESSURE COMPENSATOR
COMBINATION TYPE
COMBINATION TYPE
COMMON CAVITY
COMMON CAVITY
VCSQ-16A
VCSQ-16A
SIZE 16
04.84.06 - XSIZE
- 27 16
-Z
04.84.06 - X - 27 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. inlet flow:
53 gpm
(200 l/min)
Max. priority flow:
32 gpm
(120 l/min)
Flow maintenance:
± 10%
Cavity : CA-16A-4N (see page A10.013)
/LQHERGLHVVHHSDJH$±$
Flow is normally allowed from 4 to 3. When pilot pressure at 1 rises above the
combined pressure of the spring bias, plus pressure at 4, the valve shifts to block
flow between 3 and 4, while diverting flow from 1 to 2. A constant pressure drop is
maintained across a fixed (or variable) orifice upstream of 4 when installed and
piloted per the diagram above. In this case, flow priority is given to 3, with flow in
excess of the orifice differential requirement being by-passed to 2.
External seal kit : see page A11.012
Installation torque :
80-90 ft-lb
(108-122 Nm)
Weight:
1.654 lbs
(0.750 Kg)
X
00
ADJUSTMENTS
Fixed setting
SPRINGS
Z
06
Cracking pressure
psi
(bar)
90
(6)
Rev.0208
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
Directional Valves, Mechanically Operated.
VDSD-10A
VDP-32
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
DIRECTIONAL SPOOL TYPE,
DIRECTIONAL SPOOL TYPE,
DIRECT ACTING EXTERNAL
PILOT ACTING
EXTERNAL
VENT PILOT EXTERNAL VENT
DIRECT
EXTERNAL
COMMON CAVITY
COMMON CAVITY
VDSD-10A
VDSD-10A
SIZE 10
04.77.22 - XSIZE
- 8510
-Z
04.77.22 - X - 85 - Z
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow:
13 gpm
(50 l/min)
Int. leakage ave. :
1.5 in /min
Pilot displacement
volume:
0.02 in
3
3
(25 cm /min)
3
3
(0.28 cm )
Cavity : CA-10A-3N (see page CT.A.003.U)
/LQHERGLHVVHHSDJH01$«
Flow is allowed bi-directionally between 2 and 3 until pressure at 1 rises to overcome
the spring bias against the spool. When this bias pressure is surpassed, the spool
shifts, blocking flow at both 2 and 3. The spring chamber is sealed and vented to
atmosphere, allowing consistent shifting with only spring bias pressure independent
of conditions at 2 or 3.
External seal kit : see page A11.011
Installation torque :
30-35 ft-lb
(41-47 Nm)
Weight:
0.441 lbs
(0.200 Kg)
X
O-RING ON PILOT PISTON
00
No O-Ring
10
With O-Ring
SPRINGS
Z
05
11
Rev.1106
Setting
psi
(bar)
80 r20%
(5.5 r20%)
167 r10%
(11.5 r10%)
Page. AA6.070
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
DIRECTIONAL CONTROL VALVES
HYDRAULIC AUTOMATIC SWITCHING
SPOOL 3-WAY 2-POSITION CARTRIDGE STYLE
VDP-32
OD.71.01.51 - Z
Hex. 24
Torque 39-51 Nm
TECHNICAL DATA
Maximum Operating
Pressure
315
Rated Flow
30
Cavity - Tooling (051-E)
Weight
bar
l/min
page 7.01.110
0.195
kg
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.050
Filtration : 25 Pm nominal or
better
unrestricted
350
8
300
7
250
6
5
200
4
150
3
100
2
50
PRESSURE - ǻp (bar)
PRESSURE - ǻp (bar)
Pressure settings different from standard have
to be specified when ordering.
1
0
0
0
5
10
15
20
25
FLOW - Q (l/min)
30
35
SWITCHING PRESSURE
bar
Z
01
02
04
Rev.03.03
Adj. pressure
range
Standard setting
3-25
5
20-60
35
70-100
90
2.43.010.G
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
Shuttle Valves
VFC
SELB-08A
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SHUTTLE
VFC
05.99.05.00 - Y
TECHNICAL DATA
Operating pressure: up to 210 bar (3000 psi)
Max flow: 50 l/min (13 gpm)
Aluminium body
NOTE: aluminium bodies are often strong enough for operating
pressures exceeding 210 bar (3000 psi), depending from the
fatigue life expected in the specific application. If in doubt,
consult our Service Network.
Weigth: 0.17 kg (0.4 lbs)
Single ball shuttle valve with 3 ports for in-line plumbing: when the ports V1 and V2 are
connected to 2 work lines, the valve delivers the highest of the 2 pressures to the common
port C. The single ball allows for the decay of the pressure signal when both work ports
drop to a lower pressure level.
PORT SIZE
Y
V1-V2-C
09
Bosch Rexroth Oil Control S.p.a
G 1/4
RE 00171/02.07
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
Solenoide Valves
VED-8I-3206-SE
VEI-8A-2A-10ANC-S-NSS
VED-8I-3206-SI
VEI-8A-2A-10ANC-S-X-NSS
VED-8I-3206-NC
VEI-8A-2A-12NA-S-NSS
VED-8I-4206-CA
VEI-8A-2A-12NC-S-X-NSS
VED-8I-4306-ABT
VEI-8A-2A-06NA-S-NSS
VEI-8A-2A-06NC-S-X-NSS
VEI-8A-2A-09NA-S-NSS
VEI-8A-2A-09NC-S-X-NSS
VEI-8A-2A-10ANA-S-NSS
VEI-8A-2A-12ANA-S-NSS
VEI-8A-2T-06NA-S-NSS
VEI-8A-2T-06NC-S-NSS
VEI-8I-2A-06NC-S-NSS
VEI-8I-2A-06NC-S1-NSS
VEI-8I-2A-06NC-S1-NSS, N9
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
DIRECTIONAL POPPET TYPE,
DIRECTIONAL POPPET TYPE,
SHUTTLE
SHUTTLE
COMMON CAVITY
COMMON CAVITY
SELB-08A
SIZE 08
SELB-08A
04.94.05.00.56.00
SIZE 08
04.94.05.00.56.00
TECHNICAL DATA
Max. pressure:
5000 psi
(350 bar)
Max. flow: see performance graph
Nominal size DN 3
Cavity : CA-08A-3N (see page CT.A.003.U)
/LQHERGLHVVHHSDJH01$«
External seal kit : see page A11.011
The single ball shuttle allows flow from the higher pressure of two work ports 1 and 3
to the 2 port.
Installation torque :
25-30 ft-lb
(34-41 Nm)
Weight:
0.132 lbs
(0.060 Kg)
Rev.0606
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED
OPERATED VALVES
SOLENOID
VALVES
SPOOL
3-WAY
SPOOL 3-WAY 2-POSITION
2-POSITION
COMMON CAVITY
CAVITY
COMMON
VED-8I-32-06-SE
VED-8I-32-06-SE
SIZE 08
OD.13.10.51
OD.13.10.51 -- Y
Y -- 00
2.2-3.0 ft-lb
(3-4) Nm
Coil S8-356
Hex. .94 / 28.8-37.6 ft-lb
Hex. (24) / (39-51) Nm
TECHNICAL DATA
Maximum Operating
Pressure
3000 psi
(210 bar)
Rated Flow
3 gpm
(10 l/min)
Cavity - Tooling (CA-08A-3N)
page CT.A.003.U
Line bodies
page MN2.A…
Weight
0.286 lbs (0.130 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage at 3000 psi
(210 bar) with 46 cSt oil
Max.2.5
in³/min
Filtration : 25 Pm nominal or
better
Minimum Voltage Required
Coils must
separately
be
ordered
page 7.01.050
90% of nominal
page 1.71.042
Mounting Position
Y
(Max.40
cm³/min)
unrestricted
ORDERING OPTIONS
30 Standard
40 Knob Style Manual Override
Rev.06.05
1.31.050.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED
OPERATED VALVES
SOLENOID
VALVES
SPOOL
3-WAY
SPOOL 3-WAY 2-POSITION
2-POSITION
COMMON CAVITY
CAVITY
COMMON
VED-8I-32-06-SI
SIZE 08
VED-8I-32-06-SI
OD.13.11.51
OD.13.11.51 -- Y
Y -- 00
00
2.2-3.0 ft-lb
(3-4) Nm
Coil S8-356
Hex. .94 / 28.8-37.6 ft-lb
Hex. (24) / (39-51) Nm
TECHNICAL DATA
Maximum Operating
Pressure
3000 psi
(210 bar)
Rated Flow
3 gpm
(10 l/min)
Cavity - Tooling (CA-08A-3N)
page CT.A.003.U
Line bodies
page MN2.A…
Weight
Port 1 can be pressurized but is not intended to be used as inlet port.
0.286 lbs (0.130 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage(2 Ź 3)
at 210 bar with 46 cSt oil
Max.2.5
in³/min
(Max.40
cm³/min)
Internal Leakage(2 Ź 1)
at 210 bar with 46 cSt oil
Max.9.8
in³/min
(Max.160
cm³/min)
Filtration : 25 Pm nominal or
better
Minimum Voltage Required
Coils must
separately
be
ordered
page 7.01.050
90% of nominal
page 1.71.042
Mounting Position
Y
unrestricted
ORDERING OPTIONS
30 Standard
40 Knob Style Manual Override
Rev.06.05
1.31.100.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED
OPERATED VALVES
SOLENOID
VALVES
SPOOL
3-WAY
SPOOL 3-WAY 2-POSITION
2-POSITION
COMMON CAVITY
CAVITY
COMMON
VED-8I-32-06-NC
VED-8I-32-06-NC
SIZE 08
OD.13.20.51
OD.13.20.51 -- Y
Y -- 00
2.2-3.0 ft-lb
(3-4) Nm
Coil S8-356
Hex. .94 / 28.8-37.6 ft-lb
Hex. (24) / (39-51) Nm
TECHNICAL DATA
Maximum Operating
Pressure
3000 psi
(210 bar)
Rated Flow
3 gpm
(10 l/min)
Cavity - Tooling (CA-08A-3N)
page CT.A.003.U
Line bodies
page MN2.A…
Weight
0.286 lbs (0.130 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage at 3000 psi
(210 bar) with 46 cSt oil
Max.2.5
in³/min
Filtration : 25 Pm nominal or
better
Minimum Voltage Required
Coils must
separately
be
ordered
page 7.01.050
90% of nominal
page 1.71.042
Mounting Position
Y
(Max.40
cm³/min)
unrestricted
ORDERING OPTIONS
30 Standard
40 Knob Style Manual Override
Rev.06.05
1.31.150.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED
OPERATED VALVES
SOLENOID
VALVES
SPOOL
4-WAY
SPOOL 4-WAY 2-POSITION
2-POSITION
COMMON CAVITY
CAVITY
COMMON
VED-8I-42-06-CA
VED-8I-42-06-CA
SIZE 08
OD.14.40.58
OD.14.40.58 -- YY -- 00
00
2.2-3.0 ft-lb
(3-4) Nm
Coil S8-356
Hex. .94 / 28.8-37.6 ft-lb
Hex. (24) / (39-51) Nm
TECHNICAL DATA
Maximum Operating
Pressure
3000 psi
(210 bar)
Rated Flow
3 gpm
(10 l/min)
Cavity - Tooling (CA-08A-4N)
page CT.A.004.U
Line bodies
page MN2.A…
Weight
0.286 lbs (0.130 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage at 3000 psi
(210 bar) with 46 cSt oil
Max.2.5
in³/min
Filtration : 25 Pm nominal or
better
Minimum Voltage Required
Coils must
separately
be
ordered
page 7.01.050
90% of nominal
page 1.71.042
Mounting Position
Y
(Max.40
cm³/min)
unrestricted
ORDERING OPTIONS
30 Standard
40 Knob Style Manual Override
Rev.06.05
1.41.050.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED
OPERATED VALVES
SOLENOID
VALVES
SPOOL
4-WAY
SPOOL 4-WAY 3-POSITION
3-POSITION
COMMON CAVITY
CAVITY
COMMON
VED-8I-43-06-ABT
VED-8I-43-06-ABT
SIZE 08
OD.14.32.58
OD.14.32.58 -- YY -- 00
00
2.2-3.0 ft-lb
(3-4) Nm
Coil S8-356
Hex. .94 / 28.8-37.6 ft-lb
Hex. (24) / (39-51) Nm
TECHNICAL DATA
Maximum Operating
Pressure
3000 psi
(210 bar)
Rated Flow
3 gpm
(10 l/min)
Cavity - Tooling (CA-08A-4N)
page CT.A.004.U
Line bodies
page MN2.A…
Weight
0.397 lbs (0.180 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage at 3000 psi
(210 bar) with 46 cSt oil
Max.7.3
in³/min
Filtration : 25 Pm nominal or
better
Minimum Voltage Required
Coils must
separately
be
Mounting Position
Y
ordered
(Max.120
cm³/min)
page 7.01.050
90% of nominal
page 1.71.042
unrestricted
ORDERING OPTIONS
44 Standard
Rev.06.05
1.43.150.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED
OPERATED VALVES
SOLENOID
VALVES
POPPET
2-WAY
POPPET 2-WAY NORMALLY
NORMALLY OPEN
OPEN
COMMON CAVITY
CAVITY
COMMON
VEI-8A-2A-06-NA-S-NSS
VEI-8A-2A-06-NA-S-NSS
SIZE 08
OD.15.06.18
OD.15.06.18 -- Y
Y -- S0
PATENT PENDING
2.2-3.0 ft-lb
(3-4) Nm
Coil S8-356
Hex. .94 / 28.8-37.6 ft-lb
Hex. (24) / (39-51) Nm
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Fatigue Cycle Life at
5000 psi (350 bar) and 0.5 Hz 10 million
(1 s ON - 1 s OFF)
cycles
Rated Flow
11 gpm
Cavity - Tooling (CA-08A-2N)
(40 l/min)
page CT.A.001.U
Line bodies
page MN2.A…
Weight
0.286 lbs (0.130 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 Pm nominal or
better
page 7.01.050
Minimum Voltage Required
Coils must
separately
be
90% of nominal
ordered
page 1.71.042
Mounting Position
Y
unrestricted
ORDERING OPTIONS
1A Standard
Push
1B Override
Push
Style
and
Twist
1C Manual Override
Rev.06.05
Manual
Style
1.12B.060.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED VALVES
SOLENOID OPERATED VALVES
POPPET 2-WAY NORMALLYPOPPET
CLOSED
- EXTRA
SPRING CLOSED - EXTRA SPRING
2-WAY
NORMALLY
SPECIAL CAVITY
SPECIAL CAVITY
VEI-8A-2A-09-NC-S-X-NSSVEI-8A-2A-09-NC-S-X-NSS
017-E
OD.15.05.17017-E
- Y - S8 OD.15.05.17
- Y - S8
PATENT PENDING
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Fatigue Cycle Life at
5000 psi (350 bar) and 0.5 Hz 10 million
(1 s ON - 1 s OFF)
cycles
Rated Flow
19 gpm
Cavity - Tooling (017-E )
/LQHERGLHV
(70 l/min)
page CT.S.005.U
SDJH016«
Weight
0.485 lbs (0.220 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 Pm nominal or
better
page 7.01.050
Minimum Voltage Required
Coils must
separately
be
ordered
90% of nominal
page 1.71.042
Mounting Position
unrestricted
The only difference between this valve and the
standard model is a spring placed between pilot
section and poppet.
This design allows faster response times with very
small flow or even virtually zero flow.
A pressure of approximately 58 psi (4 bar) is
required to open the main poppet.
Y
ORDERING OPTIONS
3A Standard
3D Knob Style Manual Override
Rev.10.08
1.11B.465.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED
OPERATED VALVES
SOLENOID
VALVES
POPPET
2-WAY
POPPET 2-WAY NORMALLY
NORMALLY OPEN
OPEN
COMMON CAVITY
CAVITY
COMMON
VEI-8A-2A-10A-NA-S-NSS
VEI-8A-2A-10A-NA-S-NSS
SIZE 10
OD.15.06.36
OD.15.06.36 -- YY -- S0
S0
PATENT PENDING
2.2-3.0 ft-lb
(3-4) Nm
Coil S8-356
Hex. 1.06 / 32.5-41.3 ft-lb
Hex. (27) / (44-56) Nm
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Fatigue Cycle Life at
5000 psi (350 bar) and 0.5 Hz 10 million
(1 s ON - 1 s OFF)
cycles
Rated Flow
19 gpm
Cavity - Tooling (CA-10A-2N)
(70 l/min)
page CT.A.001.U
Line bodies
page MN1.A…
Weight
0.485 lbs (0.220 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 Pm nominal or
better
page 7.01.050
Minimum Voltage Required
Coils must
separately
be
90% of nominal
ordered
page 1.71.042
Mounting Position
Y
unrestricted
ORDERING OPTIONS
1A Standard
Push
1B Override
Push
Style
and
Twist
1C Manual Override
Rev.06.05
Manual
Style
1.16B.460.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED VALVES
SOLENOID OPERATED VALVES
POPPET 2-WAY NORMALLYPOPPET
CLOSED
- EXTRA
SPRING CLOSED - EXTRA SPRING
2-WAY
NORMALLY
SPECIAL CAVITY
SPECIAL CAVITY
VEI-8A-2A-09-NC-S-X-NSSVEI-8A-2A-09-NC-S-X-NSS
017-E
OD.15.05.17017-E
- Y - S8 OD.15.05.17
- Y - S8
PATENT PENDING
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Fatigue Cycle Life at
5000 psi (350 bar) and 0.5 Hz 10 million
(1 s ON - 1 s OFF)
cycles
Rated Flow
19 gpm
Cavity - Tooling (017-E )
/LQHERGLHV
(70 l/min)
page CT.S.005.U
SDJH016«
Weight
0.485 lbs (0.220 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 Pm nominal or
better
page 7.01.050
Minimum Voltage Required
Coils must
separately
be
ordered
90% of nominal
page 1.71.042
Mounting Position
unrestricted
The only difference between this valve and the
standard model is a spring placed between pilot
section and poppet.
This design allows faster response times with very
small flow or even virtually zero flow.
A pressure of approximately 58 psi (4 bar) is
required to open the main poppet.
Y
ORDERING OPTIONS
3A Standard
3D Knob Style Manual Override
Rev.10.08
1.11B.465.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED
OPERATED VALVES
SOLENOID
VALVES
POPPET
2-WAY
POPPET 2-WAY NORMALLY
NORMALLY OPEN
OPEN
COMMON CAVITY
CAVITY
COMMON
VEI-8A-2A-10A-NA-S-NSS
VEI-8A-2A-10A-NA-S-NSS
SIZE 10
OD.15.06.36
OD.15.06.36 -- YY -- S0
S0
PATENT PENDING
2.2-3.0 ft-lb
(3-4) Nm
Coil S8-356
Hex. 1.06 / 32.5-41.3 ft-lb
Hex. (27) / (44-56) Nm
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Fatigue Cycle Life at
5000 psi (350 bar) and 0.5 Hz 10 million
(1 s ON - 1 s OFF)
cycles
Rated Flow
19 gpm
Cavity - Tooling (CA-10A-2N)
(70 l/min)
page CT.A.001.U
Line bodies
page MN1.A…
Weight
0.485 lbs (0.220 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 Pm nominal or
better
page 7.01.050
Minimum Voltage Required
Coils must
separately
be
90% of nominal
ordered
page 1.71.042
Mounting Position
Y
unrestricted
ORDERING OPTIONS
1A Standard
Push
1B Override
Push
Style
and
Twist
1C Manual Override
Rev.06.05
Manual
Style
1.16B.460.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED VALVES
SOLENOID OPERATED VALVES
POPPET 2-WAY NORMALLYPOPPET
CLOSED2-WAY NORMALLY CLOSED
COMMON CAVITY
COMMON CAVITY
VEI-8A-2A-10A-NC-S-NSS VEI-8A-2A-10A-NC-S-NSS
SIZE 10 OD.15.05.36SIZE
- Y -10
S0
OD.15.05.36 - Y - S0
PATENT PENDING
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Fatigue Cycle Life at
5000 psi (350 bar) and 0.5 Hz 10 million
(1 s ON - 1 s OFF)
cycles
Rated Flow
19 gpm
Cavity - Tooling (CA-10A-2N)
/LQHERGLHV
(70 l/min)
page CT.A.001.U
SDJH01$«
Weight
0.485 lbs (0.220 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 Pm nominal or
better
page 7.01.050
Minimum Voltage Required
Coils must
separately
be
ordered
90% of nominal
page 1.71.042
Mounting Position
Y
unrestricted
ORDERING OPTIONS
3A Standard
3D Knob Style Manual Override
Rev.02.07
1.15B.460.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED VALVES
SOLENOID OPERATED VALVES
POPPET 2-WAY NORMALLYPOPPET
CLOSED2-WAY
- EXTRA
SPRING CLOSED - EXTRA SPRING
NORMALLY
COMMON CAVITY
COMMON CAVITY
VEI-8A-2A-10A-NC-S-X-NSSVEI-8A-2A-10A-NC-S-X-NSS
SIZE 10 OD.15.05.36SIZE
- Y -10
S8 OD.15.05.36
- Y - S8
PATENT PENDING
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Fatigue Cycle Life at
5000 psi (350 bar) and 0.5 Hz 10 million
(1 s ON - 1 s OFF)
cycles
Rated Flow
19 gpm
Cavity - Tooling (CA-10A-2N)
/LQHERGLHV
(70 l/min)
page CT.A.001.U
SDJH01$«
Weight
0.485 lbs (0.220 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 Pm nominal or
better
page 7.01.050
Minimum Voltage Required
Coils must
separately
be
ordered
90% of nominal
page 1.71.042
Mounting Position
unrestricted
The only difference between this valve and the
standard model is a spring placed between pilot
section and poppet.
This design allows faster response times with very
small flow or even virtually zero flow.
A pressure of approximately 58 psi (4 bar) is
required to open the main poppet.
Y
ORDERING OPTIONS
3A Standard
3D Knob Style Manual Override
Rev.02.07
1.15B.465.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED VALVES
SOLENOID OPERATED VALVES
POPPET 2-WAY NORMALLYPOPPET
OPEN 2-WAY NORMALLY OPEN
SPECIAL CAVITY
SPECIAL CAVITY
VEI-8A-2A-12-NA-S-NSS VEI-8A-2A-12-NA-S-NSS
021-E
OD.15.06.21021-E
- Y - S0
OD.15.06.21 - Y - S0
PATENT PENDING
2.2-3.0 ft-lb
(3-4) Nm
Coil S8-356
Hex. 1.50 / 59.0-73.8 ft-lb
Hex. (38) / (80-100) Nm
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Fatigue Cycle Life at
5000 psi (350 bar) and 0.5 Hz 10 million
(1 s ON - 1 s OFF)
cycles
Rated Flow
39 gpm
Cavity - Tooling (021-E)
(150 l/min)
page CT.S.006.U
Line bodies
page MN2.S…
Weight
0.772 lbs (0.350 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 Pm nominal or
better
page 7.01.050
Minimum Voltage Required
Coils must
separately
be
90% of nominal
ordered
page 1.71.042
Mounting Position
Y
unrestricted
ORDERING OPTIONS
1A Standard
Push
1B Override
Push
Style
and
Twist
1C Manual Override
Rev.09.05
Manual
Style
1.12B.660.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED VALVES
SOLENOID OPERATED VALVES
POPPET 2-WAY NORMALLYPOPPET
CLOSED2-WAY
- EXTRA
SPRING CLOSED - EXTRA SPRING
NORMALLY
SPECIAL CAVITY
SPECIAL CAVITY
VEI-8A-2A-12-NC-S-X-NSS
VEI-8A-2A-12-NC-S-X-NSS 021-E
OD.15.05.21021-E
- Y - S8 OD.15.05.21
- Y - S8
PATENT PENDING
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Fatigue Cycle Life at
5000 psi (350 bar) and 0.5 Hz 10 million
(1 s ON - 1 s OFF)
cycles
Rated Flow
39 gpm
Cavity - Tooling (021-E)
/LQHERGLHV
(150 l/min)
page CT.S.006.U
SDJH016«
Weight
0.772 lbs (0.350 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 Pm nominal or
better
page 7.01.050
Minimum Voltage Required
Coils must
separately
be
ordered
90% of nominal
page 1.71.042
Mounting Position
unrestricted
The only difference between this valve and the
standard model is a spring placed between pilot
section and poppet.
This design allows faster response times with very
small flow or even virtually zero flow.
A pressure of approximately 44 psi (3 bar) is
required to open the main poppet.
Y
ORDERING OPTIONS
3A Standard
3D Knob Style Manual Override
Rev.02.07
1.11B.665.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED
OPERATED VALVES
SOLENOID
VALVES
POPPET
2-WAY
POPPET 2-WAY NORMALLY
NORMALLY OPEN
OPEN
COMMON CAVITY
CAVITY
COMMON
VEI-8A-2A-12A-NA-S-NSS
VEI-8A-2A-12A-NA-S-NSS
SIZE 12
OD.15.06.89
OD.15.06.89 -- YY -- S0
S0
PATENT PENDING
2.2-3.0 ft-lb
(3-4) Nm
Coil S8-356
Hex. 1.26 / 39.8-48.7 ft-lb
Hex. (32) / (54-66) Nm
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Fatigue Cycle Life at
5000 psi (350 bar) and 0.5 Hz 10 million
(1 s ON - 1 s OFF)
cycles
Rated Flow
39 gpm
Cavity - Tooling (CA-12A-2N)
(150 l/min)
page CT.A.001.U
Line bodies
page MN1.A…
Weight
0.772 lbs (0.350 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 Pm nominal or
better
page 7.01.050
Minimum Voltage Required
Coils must
separately
be
90% of nominal
ordered
page 1.71.042
Mounting Position
Y
unrestricted
ORDERING OPTIONS
1A Standard
Push
1B Override
Push
Style
and
Twist
1C Manual Override
Rev.06.05
Manual
Style
1.16B.660.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED
OPERATED VALVES
SOLENOID
VALVES
POPPET
2-WAY
POPPET 2-WAY DOUBLE
DOUBLE LOCK
LOCK NORMALLY
NORMALLY OPEN
OPEN
COMMON
CAVITY
COMMON CAVITY
VEI-8A-2T-06-NA-S-NSS
VEI-8A-2T-06-NA-S-NSS
SIZE 08 OD.15.32.18
OD.15.32.18 -- YY -- S0
S0
PATENT PENDING
2.2-3.0 ft-lb
(3-4) Nm
Coil S8-356
Hex. .94 / 28.8-37.6 ft-lb
Hex. (24) / (39-51) Nm
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Fatigue Cycle Life at
5000 psi (350 bar) and 0.5 Hz 10 million
(1 s ON - 1 s OFF)
cycles
Rated Flow
11 gpm
Cavity - Tooling (CA-08A-2N)
(40 l/min)
page CT.A.001.U
Line bodies
page MN2.A…
Weight
0.286 lbs (0.130 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 Pm nominal or
better
page 7.01.050
Minimum Voltage Required
Coils must
separately
be
90% of nominal
ordered
page 1.71.042
Mounting Position
Y
unrestricted
ORDERING OPTIONS
1A Standard
Push
1B Override
Push
Style
and
Twist
1C Manual Override
Rev.06.05
Manual
Style
1.14B.060.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED VALVES
SOLENOID OPERATED VALVES
POPPET 2-WAY DOUBLE LOCK
NORMALLY
CLOSEDLOCK NORMALLY CLOSED
POPPET
2-WAY DOUBLE
COMMON CAVITY
COMMON CAVITY
VEI-8A-2T-06-NC-S-NSSVEI-8A-2T-06-NC-S-NSS
SIZE 08 OD.15.31.18SIZE
- Y -08
S0 OD.15.31.18
- Y - S0
PATENT PENDING
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Fatigue Cycle Life at
5000 psi (350 bar) and 0.5 Hz 10 million
(1 s ON - 1 s OFF)
cycles
Rated Flow
11 gpm
Cavity - Tooling (CA-08A-2N)
/LQHERGLHV
(40 l/min)
page CT.A.001.U
SDJH01$«
Weight
0.286 lbs (0.130 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 Pm nominal or
better
page 7.01.050
Minimum Voltage Required
Coils must
separately
be
ordered
90% of nominal
page 1.71.042
Mounting Position
Y
unrestricted
ORDERING OPTIONS
3A Standard
3D Knob Style Manual Override
Rev.02.07
1.13B.060.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED VALVES
SOLENOID OPERATED VALVES
POPPET 2-WAY NORMALLYPOPPET
CLOSED2-WAY NORMALLY CLOSED
COMMON CAVITY
COMMON CAVITY
VEI-8I-2A-06-NC-S-NSS VEI-8I-2A-06-NC-S-NSS
SIZE 08 OD.15.05.18SIZE
- Y -08
S0
OD.15.05.18 - Y - S0
PATENT PENDING
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Fatigue Cycle Life at
5000 psi (350 bar) and 0.5 Hz 10 million
(1 s ON - 1 s OFF)
cycles
Rated Flow
8 gpm
Cavity - Tooling (CA-08A-2N)
(30 l/min)
page CT.A.001.U
/LQHERGLHV
SDJH01$«
Weight
0.286 lbs (0.130 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 µm nominal or
better
page 7.01.050
Minimum Voltage Required
Coils must
separately
be
ordered
90% of nominal
page 1.71.042
Mounting Position
Y
3I
unrestricted
ORDERING OPTIONS
Standard
3M Knob Style Manual Override
Rev.01.07
1.11B.050.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED VALVES
SOLENOID OPERATED VALVES
POPPET 2-WAY NORMALLYPOPPET
CLOSED2-WAY NORMALLY CLOSED
COMMON CAVITY
COMMON CAVITY
VEI-8I-2A-06-NC-S1-NSSVEI-8I-2A-06-NC-S1-NSS
SIZE 08 OD.15.01.18SIZE
- Y -08
S0
OD.15.01.18 - Y - S0
PATENT PENDING
TECHNICAL DATA
Maximum Operating
Pressure
5000 psi
(350 bar)
Fatigue Cycle Life at
5000 psi (350 bar) and 0.5 Hz 10 million
(1 s ON - 1 s OFF)
cycles
Rated Flow
8 gpm
Cavity - Tooling (CA-08A-2N)
(30 l/min)
page CT.A.001.U
/LQHERGLHV
SDJH01$«
Weight
0.286 lbs (0.130 kg)
Fluids - Temperatures
page 7.01.040
Testing Conditions - Seals
page 7.01.040
Internal Leakage
page 7.01.040
Filtration : 25 µm nominal or
better
page 7.01.050
Minimum Voltage Required
Coils must
separately
be
ordered
90% of nominal
page 1.71.042
Mounting Position
Y
3I
unrestricted
ORDERING OPTIONS
Standard
3M Knob Style Manual Override
Rev.01.07
1.11B.030.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED VALVES
SOLENOID OPERATED VALVES
CONTINUOUS DUTY COILSCONTINUOUS
- ED 100%
DUTY COILS - ED 100%
S8-356 SERIES - CLASS H S8-356 SERIES - CLASS
OD.02.17
H
-X-Y-Z
OD.02.17 - X - Y - Z
TECHNICAL DATA
General coil information
page 7.01.010
Weight
S8-H
S8-A
S8-G
DIN 43650 - ISO 4400
AMP JUNIOR
SINGLE LEAD
0.397 lbs (0.180 kg)
Encapsulating material
IXEF
HEAT INSULATION
CLASS H
356 qF
(180 qC)
Ambient temperature range
-86 +140
°F
(-30 +60
°C)
Available on request : Different Voltages - Different
connectors mounted on single lead.
Inlet voltage fluctuations must not exceed r 10% of
nominal voltage to obtain correct operation and long
life of coils.
X
Y
Connections
Circuit
Voltage
01
07
0G
14
15
0H
30
30
03
30
30
03
DIN 43650 - ISO 4400
Standard
DC-RAC
Z
OB
OC
OV
OW
OZ
OG
AC
Rev.06.05
AMP JUNIOR
Standard
DC only
SINGLE LEAD
Standard
DC only
DIN 43650 - ISO 4400
Bidirectional Diode
DC only
AMP JUNIOR
Bidirectional Diode
DC only
SINGLE LEAD
Bidirectional Diode
DC only
Current
A
Voltage
V
Resistance
ȍ (±7%)
Power
W
Nominal
Ta = 68-77 °F (20-25 °C)
Cold Coil
Cold Coil
Hot Coil
12 DC
7.4
20
1.62
1.19
24 DC
28.5
20
0.85
0.61
24 RAC
20
110 RAC
20
220 RAC
20
14 DC
20
26 DC
34.3
20
Length
11.8 inches (300 mm)
Ext. diameter
0.25 inches (6.3 mm)
External and Internal Sheath
Silicone rubber
'T
°F (°C)
1 hour energized at
Ta = 68-77 °F (20-25 °C)
Nominal Voltage
221-230 (105-110)
0.76
0.54
1.71.042.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SOLENOID OPERATED
OPERATED VALVES
VALVES
SOLENOID
CONTINUOUS
DUTY
COILS
ED 100%
100%
CONTINUOUS DUTY COILS -- ED
OD.02.17
OD.02.17 -- X
X -- Y
Y -- Z
S8-356SERIES
SERIES--CLASS
CLASSHH
S8-356
TECHNICAL DATA
General coil information
S8-DTL
S8-DTV
S8-ASV
DEUTSCH DT04-2P-L
DEUTSCH DT04-2P-V
AMP SUPERSEAL-V
page 7.01.010
Weight
0.397 lbs (0.180 kg)
Encapsulating material
IXEF
Protection IP 69K
These coils have passed the
THERMAL
SHOCK
DUNK
TEST, see
DIN 40050 part 9
page 7.01.010
HEAT INSULATION
CLASS H
356 qF
(180 qC)
Ambient temperature range
-86 +140
°F
(-30 +60
°C)
Available on request : Different Voltages - Different
connectors mounted on single lead.
Inlet voltage fluctuations must not exceed r 10% of
nominal voltage to obtain correct operation and long
life of coils.
X
Y
Connections
Circuit
Voltage
20
20
30
22
22
32
30
3P
3P
30
3P
3P
DEUTSCH DT04-2P-L
Standard
DC only
DEUTSCH DT04-2P-V
Standard
DC only
AMP SUPERSEAL-V
Standard
DC only
Z
OB
OC
AC
DEUTSCH DT04-2P-L
Bidirectional Diode
DC only
DEUTSCH DT04-2P-V
Bidirectional Diode
DC only
AMP SUPERSEAL-V
Bidirectional Diode
DC only
Current
A
Voltage
V
Resistance
ȍ (±7%)
Power
W
Nominal
Ta = 68-77 °F (20-25 °C)
Cold Coil
Cold Coil
Hot Coil
12 DC
7.4
20
1.62
1.19
24 DC
28.5
20
0.85
0.61
26 DC
34.3
20
0.76
0.54
'T
°F (°C)
1 hour energized at
Ta = 68-77 °F (20-25 °C)
Nominal Voltage
221-230 (105-110)
Rev.06.05
1.71.043.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
STANDARD MANIFOLDS (SECTION
2) MANIFOLDS (SECTION 2)
STANDARD
COMMON CAVITY
COMMON CAVITY
2 WAY ALUMINIUM
SIZE
08
2 WAY
ALUMINIUM
CAVITY
CA-08A-2N
Dimensions on page
CT.A.001.U
ORDERING
CODE
PORTS
WEIGHT
A-B
Lbs (Kg)
OC.10.09.009
G 1/4
0.331
(0.150)
OC.10.09.004
G 3/8
0.331
(0.150)
SIZE 08
FEATURES
MAX. PRESSURE
Rev.07.06
3600 psi
(250 bar)
Standard manifolds in high-strength aluminum
for working pressures up to 3600 psi (250 bar).
MN2.A.001.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
MANIFOLDS
MANIFOLDS (SECTION
(SECTION 2)
2)
COMMON
CAVITY
COMMON CAVITY
WAYSTEEL
STEEL
22WAY
CAVITY
CA-08A-2N
Dimensions on page
CT.A.001.U
ORDERING
CODE
PORTS
WEIGHT
A-B
Lbs (Kg)
OC.10.09.067
G 1/4
0.992
(0.450)
OC.10.09.066
G 3/8
0.992
(0.450)
SIZE
SIZE 08
08
FEATURES
MAX. PRESSURE
Rev.05.05
6500 psi
(450 bar)
These manifolds can be supplied upon request
for working pressures up to 6500 psi (450 bar)
and for fatigue cycle applications.
MN2.A.002.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
STANDARD MANIFOLDS (SECTION
2) MANIFOLDS (SECTION 2)
STANDARD
COMMON CAVITY
COMMON CAVITY
3 WAY 4 WAY ALUMINIUM3 WAY
SIZE
08 ALUMINIUM
4 WAY
CAVITY
CA-08A-3N
Dimensions on page
CT.A.003.U
PORTS
WEIGHT
P-C-C1/T
Lbs (Kg)
OC.10.09.042
G 1/4
0.331
(0.150)
OC.10.09.048
G 3/8
0.331
(0.150)
ORDERING
CODE
SIZE 08
CAVITY
CA-08A-4N
Dimensions on page
CT.A.004.U
ORDERING
CODE
PORTS
WEIGHT
A-B-P-T
Lbs (Kg)
OC.10.09.047
G 1/4
0.331
(0.150)
OC.10.09.046
G 3/8
0.331
(0.150)
FEATURES
MAX. PRESSURE
Rev.07.06
3600 psi
(250 bar)
Standard manifolds in high-strength aluminum
for working pressures up to 3600 psi (250 bar).
MN2.A.003.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
STANDARD
STANDARD MANIFOLDS
MANIFOLDS (SECTION
(SECTION 2)
2)
COMMON
CAVITY
COMMON CAVITY
WAY 4
4 WAY
WAY ALUMINIUM
33 WAY
ALUMINIUM
CAVITY
CA-10A-3N
Dimensions on page
CT.A.003.U
PORTS
WEIGHT
P-C-C1/T
Lbs (Kg)
OC.10.09.116
G 1/4
0.375
(0.170)
OC.10.09.115
G 3/8
0.375
(0.170)
ORDERING
CODE
SIZE
SIZE 10
10
CAVITY
CA-10A-4N
Dimensions on page
CT.A.004.U
ORDERING
CODE
PORTS
WEIGHT
A-B-P-T
Lbs (Kg)
OC.10.09.117
G 1/4
0.375
(0.170)
OC.10.09.118
G 3/8
0.375
(0.170)
FEATURES
MAX. PRESSURE
Rev.07.06
3600 psi
(250 bar)
Standard manifolds in high-strength aluminum
for working pressures up to 3600 psi (250 bar).
MN2.A.004.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
MANIFOLDS (SECTION 2) MANIFOLDS (SECTION 2)
SPECIAL CAVITY
SPECIAL CAVITY
2 WAY ALUMINIUM
CAVITY
2 WAY ALUMINIUM
017-E
Dimensions on page
CT.S.005.U
ORDERING
CODE
PORTS
WEIGHT
A-B
Lbs (Kg)
OC.10.09.015
G 1/2
0.441
(0.200)
OC.10.09.012
G 3/4
0.441
(0.200)
CAVITY
021-E
Dimensions on page
CT.S.005.U
ORDERING
CODE
PORTS
WEIGHT
A-B
Lbs (Kg)
OC.10.09.017
G 3/4
1.367
(0.620)
OC.10.09.019
G1
1.367
(0.620)
FEATURES
MAX. PRESSURE
Rev.07.06
3600 psi
(250 bar)
Standard manifolds in high-strength aluminum
for working pressures up to 3600 psi (250 bar).
MN2.S.001.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
MANIFOLDS (SECTION 2) MANIFOLDS (SECTION 2)
SPECIAL CAVITY
SPECIAL CAVITY
2 WAY ALUMINIUM
CAVITY
2 WAY ALUMINIUM
019-E
Dimensions on page
CT.S.005.U
ORDERING
CODE
PORTS
WEIGHT
A-B
Lbs (Kg)
OC.10.09.103
G 1/4
0.331
(0.150)
OC.10.09.054
G 3/8
0.331
(0.150)
CAVITY
004
Dimensions on page
CT.S.001.U
ORDERING
CODE
PORTS
WEIGHT
A-B
Lbs (Kg)
OC.10.09.040
G1
2.646
(1.200)
OC.10.09.041
G 1-1/4
2.646
(1.200)
CAVITY
081-E
Dimensions on page
CT.S.005.U
ORDERING
CODE
PORTS
WEIGHT
A-P-T
Lbs (Kg)
OC.10.09.128
G 1/4
0.397
(0.180)
FEATURES
MAX. PRESSURE
Rev.07.06
3600 psi
(250 bar)
Standard manifolds in high-strength aluminum
for working pressures up to 3600 psi (250 bar).
MN2.S.003.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
MANIFOLDS
MANIFOLDS (SECTION
(SECTION 2)
2)
SPECIAL
CAVITY
SPECIAL CAVITY
WAYSTEEL
STEEL
22WAY
CAVITY
017-E
Dimensions on page
CT.S.005.U
ORDERING
CODE
PORTS
WEIGHT
A-B
Lbs (Kg)
OC.10.09.074
G 1/2
1.984
(0.900)
OC.10.09.073
G 3/4
1.984
(0.900)
CAVITY
021-E
Dimensions on page
CT.S.005.U
ORDERING
CODE
PORTS
WEIGHT
A-B
Lbs (Kg)
OC.10.09.075
G 3/4
2.866
(1.300)
OC.10.09.076
G1
2.866
(1.300)
FEATURES
MAX. PRESSURE
Rev.05.05
6500 psi
(450 bar)
These manifolds can be supplied upon request
for working pressures up to 6500 psi (450 bar)
and for fatigue cycle applications.
MN2.S.002.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
MANIFOLDS
MANIFOLDS (SECTION
(SECTION 2)
2)
SPECIAL
CAVITY
SPECIAL CAVITY
WAYSTEEL
STEEL
22WAY
CAVITY
019-E
Dimensions on page
CT.S.005.U
ORDERING
CODE
PORTS
WEIGHT
A-B
Lbs (Kg)
OC.10.09.102
G 1/4
0.992
(0.450)
OC.10.09.101
G 3/8
0.992
(0.450)
CAVITY
004
Dimensions on page
CT.S.001.U
ORDERING
CODE
PORTS
WEIGHT
A-B
Lbs (Kg)
OC.10.09.122
G1
7.716
(3.500)
OC.10.09.056
G 1-1/4
7.716
(3.500)
CAVITY
081-E
Dimensions on page
CT.S.005.U
ORDERING
CODE
PORTS
WEIGHT
A-P-T
Lbs (Kg)
OC.10.09.162
G 1/4
1.191
(0.540)
FEATURES
MAX. PRESSURE
Rev.05.05
6500 psi
(450 bar)
These manifolds can be supplied upon request
for working pressures up to 6500 psi (450 bar)
and for fatigue cycle applications.
MN2.S.004.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
STANDARD MANIFOLDS
MANIFOLDS (SECTION
(SECTION 1)
1)
STANDARD
COMMON
CAVITY
COMMON CAVITY
CA-xxx-2N
CA-xxx-2N
CAVITY
ORDERING CODES
B
C
D
E
F
G
H
I
L
P
Aluminium
Steel
G 1/4
50
50
30
21
12
35
9
15
M
N
7
03.30.05.168
03.30.05.169
G 3/8
50
50
30
21
12
35
9
15
7
03.30.05.170
03.30.05.171
7/16-20
50
50
30
21
12
35
9
15
7
03.30.05.172
03.30.05.173
9/16-18
50
50
30
21
12
35
9
15
7
03.30.05.174
03.30.05.175
G 3/8
60
60
35
25
15
45
7
19
7
03.30.05.176
03.30.05.177
G 1/2
60
60
35
25
15
45
7
19
7
03.30.05.178
03.30.05.179
03.30.05.180
03.30.05.181
G 3/4
60
70
40
30
15
55
9
20
9
9/16-18
60
60
35
25
15
45
7
19
7
03.30.05.226
3/4-16
60
60
35
25
15
45
7
19
7
03.30.05.182
03.30.05.183
7/8-14
60
60
35
25
15
45
7.5
19
7
03.30.05.247
03.30.05.248
G 1/2
75
80
40
35
20
60
10
26.5
9
03.30.05.228
03.30.05.229
G 3/4
75
80
40
35
20
60
10
26.5
9
03.30.05.289
03.30.05.290
G 3/4
80
80
50
32
22
60
10
26
9
03.30.05.166
03.30.05.184
G1
80
90
50
37
22
60
20
26
9
03.30.05.216
03.30.05.215
1-1/16-12
80
80
50
32
22
60
10
26
9
03.30.05.185
03.30.05.186
CA-20A-2N
CA-16A-2N
CA-12A-2N
CA-10A-2N
CA-08A-2N
A
DIMENSIONS (mm)
Available on request Ports ISO 6149 and JIS B 2351-90 type 0
Rev.1205
Page MN1.A.001.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
STANDARD MANIFOLDS (SECTION
1) MANIFOLDS (SECTION 1)
STANDARD
COMMON CAVITY
COMMON CAVITY
CA-xxx-3C
CA-xxx-3C
CAVITY
ORDERING CODES
B1
C
D
E
F
G
H
I
L
M
P
Aluminium
Steel
G 1/4
60
60
30
30
15
45
7.5
13
27
7
03.30.05.187
03.30.05.188
7/16-20
60
60
30
30
15
45
7.5
13
27
7
03.30.05.189
03.30.05.190
9/16-18
G 3/8
G 1/4
70
60
35
30
15
45
7.5
15
32
7
03.30.05.192
G 1/2
G 1/4
70
70
35
32
15
55
7.5
15
32
7
03.30.05.193
9/16-18
7/16-20
70
70
35
32
15
55
7.5
15
32
7
03.30.05.195
03.30.05.196
7/8-14
9/16-18
70
70
35
32
15
55
7.5
15
32
7
03.30.05.243
03.30.05.244
CA-20A-3C
CA-16A-3C
CA-12A-3C
CA-08A-3C
B
G 3/8
CA-10A-3C
A
DIMENSIONS (mm)
03.30.05.194
G 1/2
G 1/4
80
75
40
35
15
55
10
24
42
7
03.30.05.217
03.30.05.218
7/8-14
9/16-18
80
75
40
35
15
55
10
24
42
7
03.30.05.245
03.30.05.246
G1
G 1/4
90
90
50
40
22
70
10
18.5
39
9
03.30.05.167
03.30.05.197
90
90
50
40
22
70
10
18.5
39
9
03.30.05.198
03.30.05.199
1-5/16-12 7/16-20
G 1-1/4
G 1/4
110
100
60
45
25
75
12.5
21
51
11
03.30.05.200
03.30.05.201
1-5/8-12
7/16-20
110
100
60
45
25
75
12.5
21
51
11
03.30.05.202
03.30.05.203
Available on request Ports ISO 6149 and JIS B 2351-90 type 0
Rev.0605
Page MN1.A.002.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
STANDARD MANIFOLDS
MANIFOLDS (SECTION
(SECTION 1)
1)
STANDARD
COMMON
CAVITY
COMMON CAVITY
CA-xxx-3N
CAVITY
B
C
D
E
F
G
H
ORDERING CODES
I
L
M
N
P
Aluminium
Steel
G 3/8
70
60
35
30
15
45
7.5
18
34.5
7
03.30.05.204
03.30.05.205
9/16-18
70
60
35
30
15
45
7.5
18
34.5
7
03.30.05.206
03.30.05.207
G 3/4
100
90
50
45
20
60
15
26
54.5
10.5
03.30.05.232
03.30.05.233
CA-20A-3N
CA-16A-3N
CA-12A-3N
CA-10A-3N
CA-08A-3N
A
DIMENSIONS (mm)
Available on request Ports ISO 6149 and JIS B 2351-90 type 0
Rev.0605
Page MN1.A.003.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
STANDARD MANIFOLDS (SECTION
1) MANIFOLDS (SECTION 1)
STANDARD
COMMON CAVITY
COMMON CAVITY
CA-xxx-4N
CA-xxx-4N
CAVITY
B
C
D
E
F
G
H
ORDERING CODES
I
L
M
N
P
Aluminium
Steel
G 3/8
85
60
35
30
15
45
7.5
19
35
51
7
03.30.05.211
03.30.05.209
9/16-18
85
60
35
30
15
45
7.5
19
35
51
7
03.30.05.249
03.30.05.250
G 3/4
130
90
50
45
20
60
15
26
54.5
83
10.5
03.30.05.230
03.30.05.231
1-1/16-12
125
90
50
45
15
60
15
26
54.5
83
9
03.30.05.251
03.30.05.252
CA-20A-4N
CA-16A-4N
CA-12A-4N
CA-10A-4N
CA-08A-4N
A
DIMENSIONS (mm)
Available on request Ports ISO 6149 and JIS B 2351-90 type 0
Rev.0605
Page MN1.A.004.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
STANDARD MANIFOLDS
MANIFOLDS (SECTION
(SECTION 1)
1)
STANDARD
COMMON
CAVITY
COMMON CAVITY
CA-xxx-4N
CAVITY
ORDERING CODES
B
C
D
E
F
G
H
I
L
M
N
P
G 3/8
75
60
35
30
15
50
10
19
35
51
7
1-1/16-12
115
90
50
45
15
80
15
26
54.5
83
9
Aluminium
Steel
CA-08A-4N
A
DIMENSIONS (mm)
CA-12A-4N
CA-10A-4N
03.30.05.210
03.30.05.254
CA-20A-4N
CA-16A-4N
03.30.05.253
Available on request Ports ISO 6149 and JIS B 2351-90 type 0
Rev.0605
Page MN1.A.005.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
STANDARD CAVITIESSTANDARD
- TOOLS CAVITIES - TOOLS
TOOLS
ORDERING CODE
(ALUMINIUM/STEEL *)
DRILL
Ø G1
Ø G1
Ø G1
Ø G1
Ø G1
FORM DRILL
P-CA-08A-2N P-CA-10A-2N P-CA-12A-2N P-CA-16A-2N P-CA-20A-2N
FORM REAMER
A-CA-08A-2N A-CA-10A-2N A-CA-12A-2N A-CA-16A-2N A-CA-20A-2N
PLUG TAP
M-CA-08A
M-CA-10A
M-CA-12A
M-CA-16A
M-CA-20A
* NOTE: Special heavy duty tools are available upon request, for steel drilling.
inches (mm)
Rev.0605
Page CT.A.001.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
STANDARD CAVITIESSTANDARD
- TOOLS CAVITIES - TOOLS
TOOLS
ORDERING CODE
(ALUMINIUM/STEEL *)
DRILL
Ø G1
Ø G1
Ø G1
Ø G1
Ø G1
FORM DRILL
P-CA-08A-3N P-CA-10A-3N P-CA-12A-3N P-CA-16A-3N P-CA-20A-3N
FORM REAMER
A-CA-08A-3N A-CA-10A-3N A-CA-12A-3N A-CA-16A-3N A-CA-20A-3N
PLUG TAP
M-CA-08A
M-CA-10A
M-CA-12A
M-CA-16A
M-CA-20A
* NOTE: Special heavy duty tools are available upon request, for steel drilling.
inches (mm)
Rev.0605
Page CT.A.003.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
STANDARD CAVITIES
CAVITIES - TOOLS
STANDARD
TOOLS
ORDERING CODE
(ALUMINIUM/STEEL *)
DRILL
Ø G2
Ø G2
Ø G2
Ø G2
Ø G2
FORM DRILL
P-CA-08A-3C P-CA-10A-3C P-CA-12A-3C P-CA-16A-3C P-CA-20A-3C
FORM REAMER
A-CA-08A-3C A-CA-10A-3C A-CA-12A-3C A-CA-16A-3C A-CA-20A-3C
PLUG TAP
M-CA-08A
M-CA-10A
M-CA-12A
M-CA-16A
M-CA-20A
* NOTE: Special heavy duty tools are available upon request, for steel drilling.
inches (mm)
Rev.0605
Page CT.A.002.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
STANDARD CAVITIES - TOOLS
STANDARD
TOOLS
ORDERING CODE
(ALUMINIUM/STEEL *)
DRILL
Ø G1
Ø G1
Ø G1
Ø G1
Ø G1
FORM DRILL
P-CA-08A-4N P-CA-10A-4N P-CA-12A-4N P-CA-16A-4N P-CA-20A-4N
FORM REAMER
A-CA-08A-4N A-CA-10A-4N A-CA-12A-4N A-CA-16A-4N A-CA-20A-4N
PLUG TAP
M-CA-08A
M-CA-10A
M-CA-12A
M-CA-16A
M-CA-20A
* NOTE: Special heavy duty tools are available upon request, for steel drilling.
inches (mm)
Rev.0206
Page CT.A.004.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SPECIAL CAVITIES
SPECIAL CAVITIES
003
004
005
006
008
009
General tolerance : ± 0.3mm
Rev.1005
Page CT.S.001.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SPECIAL
SPECIAL CAVITIES
CAVITIES
033
059
063
065
072
137
General tolerances : ± 0.3mm
Rev.0605
Page CT.S.002.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SPECIAL CAVITIES SPECIAL CAVITIES
348
416
625
690
730
730-A
General tolerances : ± 0.3mm
Rev.0905
Page CT.S.003.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SPECIAL CAVITIES
CAVITIES
SPECIAL
771
808
869
870
871
General tolerances : ± 0.3mm
Rev.0905
Page CT.S.004.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SPECIAL CAVITIES SPECIAL CAVITIES
CA-07A-3N
CC063A-01
CD072A-01
CD073A-01
General tolerances : ± 0.3mm
Rev.0607
Page CT.S.005.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
SPECIAL
SPECIAL CAVITIES
CAVITIES
017-E
019-E
021-E
081-E
General tolerance : ± 0.3mm
Rev.0905
Page CT.S.006.U
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
Group
BROC Catalog Code
Denomination
Rexroth Code
R901113599
R901097728
R901091914
R901113609
R901113610
R901115702
R901113622
R901113624
R901113626
R901109725
R901109726
R901097722
R901104103
R901106472
R901097730
R901104112
R901104118
R901109740
R901102333
R901109742
R901127828
R931000021
R901161819
R931000017
R901087794
R901064101
R901106627
R901106629
R901092653
R901106635
R901007308
R901106550
R901106596
R901106601
R901106613
R901106614
R901106616
R901095960
R901095961
R901096037
R901096029
R901096044
R901096043
R901096048
R901096047
R901109368
R901109839
R901095981
VRFD-10
04.04.02.04.85.40.000
relief, direct acting guided poppet type, common cavity
relief, direct acting guided poppet type, common cavity
relief, direct acting guided poppet type, common cavity
relief, direct acting guided poppet type, common cavity
relief, direct acting guided poppet type, common cavity
relief, direct acting guided poppet type, common cavity
relief, direct acting guided poppet type, common cavity
relief, direct acting guided poppet type, common cavity
relief, direct acting guided poppet type, common cavity
relief, bidirectional, direct acting poppet type differential area, common cavity
relief, bidirectional, direct acting poppet type differential area, common cavity
relief, pilot operated, spool type, common cavity
relief, pilot operated, spool type, common cavity
pilot operated sequence valve, spool type, external drain, common cavity
pilot operated sequence valve, spool type, external drain, common cavity
pressure reducing, pilot operated, spool type, common cavity
pressure reducing and relieving, pilot operated spool type, common cavity
pressure reducing and relieving, direct acting spool type, common cavity
pressure reducing and relieving, direct acting spool type, common cavity
pressure reducing and relieving, direct acting spool type, common cavity
hose burst
hose burst
hose burst
hose burst
check, poppet type
check, poppet type
pilot operated check, common cavity
pilot operated check, common cavity
pilot operated check, common cavity
pilot operated check, common cavity
check poppet type, 1 bar cracking, common cavity
check poppet type, 5 bar cracking, common cavity
check poppet type, 1 bar cracking, common cavity
check poppet type, 5 bar cracking, common cavity
check poppet type, 1 bar cracking, common cavity
check poppet type, 5 bar cracking, common cavity
check poppet type, common cavity
counterbalance, std. guided poppet type, common cavity
counterbalance, std. guided poppet type, common cavity
counterbalance, std. poppet type, diff area, 3:1, 140 - 350bar, common cavity
counterbalance, std. poppet type, diff area, 3:1, 70 - 210bar, common cavity
counterbalance, std. poppet type, diff area, 4:1, 140 - 350bar, common cavity
counterbalance, std. poppet type, diff area, 4:1, 70 - 210bar, common cavity
counterbalance, std. poppet type, diff area, 4:1, 140 - 350bar, common cavity
counterbalance, std. poppet type, diff area, 4:1, 70 - 210bar, common cavity
needle restrictor with free reverse flow, common cavity
needle restrictor, free reverse flow, common cavity
flow control, 2-way pressure compensated, fully adjustable, common cavity
flow control, 3-way pressure compensated, combination type fully adjustable, common
cavity
flow divider and combiner, common cavity
flow divider and combiner, common cavity
flow divider and combiner, common cavity
cartridge restrictor, common cavity
cartridge restrictor, common cavity
cartridge restrictor, common cavity
cartridge restrictor, common cavity
cartridge restrictor, common cavity
Logic Element, adjustable, 2-8 bar, common cavity
Logic Element, adjustable, 4-12 bar, common cavity
Logic Element, fixed setting, 11,5 bar, common cavity
Logic Element, adjustable, 2-8 bar, common cavity
Logic Element, adjustable, 4-12 bar, common cavity
logic element, pressure compensator, combination type, common cavity
directional spool type, direct actig external pilot, external vented, common cavity
directional control valves, hydraulic automatic switching, spool 3-way 2-position cartridge
style, special cavity
directional control valves, hydraulic automatic switching, spool 3-way 2-position cartridge
style, special cavity
directional control valves, hydraulic automatic switching, spool 3-way 2-position cartridge
style, special cavity
shuttle
shuttle, common cavity
solenoid operated valves, spool 3-way 2-position, common cavity
solenoid operated valves, spool 3-way 2-position, common cavity
solenoid operated valves, spool 3-way 2-position, common cavity
solenoid operated valves, spool 3-way 2-position, common cavity
solenoid operated valves, spool 4-way 2-position, common cavity
solenoid operated valves, spool 4-way 3-position, common cavity
X
X
X
X
X
X
X
X
X
VRFB-10A
04.11.49.03.56.10.000
04.11.49.03.56.20.000
04.11.49.03.56.35.000
04.11.55.03.85.10.000
04.11.55.03.85.20.000
04.11.55.03.85.35.000
04.11.56.03.85.10.000
04.11.56.03.85.20.000
04.11.56.03.85.35.000
04.11.59.03.85.10.000
04.11.59.03.85.20.000
04.12.08.03.85.20.000
04.12.08.03.85.35.000
04.13.05.03.85.10.000
04.13.05.03.85.20.000
04.93.06.03.85.10.000
04.93.07.03.85.10.000
04.95.04.03.85.02.00A
04.95.04.03.85.04.00A
04.95.04.03.85.08.00A
0T.F4.01.03.03.00.000
0T.F4.01.03.09.00.000
0T.F4.01.03.04.00.000
0T.F4.01.03.02.00.000
0T.U5.01.00.03.00.000
0T.U5.01.00.02.00.000
04.33.06.00.56.00.000
04.33.05.00.85.00.000
04.33.07.00.57.00.000
04.33.08.00.27.00.000
04.31.20.00.56.00.000
04.31.20.00.56.05.000
04.31.23.00.85.00.000
04.31.23.00.85.05.000
04.31.28.00.57.00.000
04.31.28.00.57.05.000
04.31.25.00.27.00.000
04.52.20.03.56.20.000
04.52.20.03.56.35.000
04.52.31.03.85.35.000
04.52.31.03.85.20.000
04.52.28.03.57.35.000
04.52.28.03.57.20.000
04.52.29.03.27.35.000
04.52.29.03.27.20.000
04.01.02.03.56.00.000
04.01.02.04.56.00.000
04.02.02.04.85.40.000
R901106675
X
VSBN-08A
VSBN-10A
VSBG-10A
Pressure Control Valves
VSNG - 10A
VSPN - 10A
VSPY - 10A
VRPP - 10A
VRPX - 10A
VRPR - 10A
Special Valves
VPN1
VUH1
VSON - 08A
VSON - 10A
VSON - 12A
VSON - 16A
Check Valves
VUCN - 08A
VUCN - 10A
VUCN - 12A
VUCN - 16A
VBSN - 08AA
VBSN - 10A
Counterbalance Valves
VBSN - 12A
VBSN - 16A
STVU - 08A
Flow Control Valves
ST - C - 12A
ST - C - 16A
VLST-10A
VLST-16A
VLST-20A
VLSP-10A
VLSP-16A
VCSQ - 16A
VDSD - 10A
04.05.01.00.85.16.000
04.05.01.00.85.30.000
04.05.01.00.85.40.000
OD.21.01.03.56.00.000
OD.21.01.03.36.00.000
OD.21.01.04.36.00.000
OD.21.01.03.89.00.000
OD.21.01.03.75.00.000
04.84.01.03.85.00.000
04.84.01.03.27.00.000
04.84.01.00.58.11.000
04.84.03.03.85.00.000
04.84.03.03.27.00.000
04.84.06.00.27.06.000
04.77.22.00.85.05.000
VDP-32
OD.71.01.51.02.00.000
DRFN - 10A
ST - C - 06
ST - C - 10A
Logic Elements
OD.71.01.51.01.00.000
Directional Valves,
Mechanically Operated.
OD.71.01.51.04.00.000
Shuttle Valves
VFC
SELB - 08A
VED-8I-32-06-SE
Solenoid Valves
VED-8I-32-06-SI
VED-8I-32-06-NC
VED-8I-42-06-CA
VED-8I-43-06-ABT
VEI - 8A - 2A - 06 NA - S - NSS
VEI - 8A - 2A - 06 NC - S - X - NSS
VEI - 8A - 2A - 09 NA - S - NSS
VEI - 8A - 2A - 09 NC - S - X - NSS
VEI - 8A - 2A - 10A NA - S - NSS
VEI - 8A - 2A - 10A NC - S - NSS
VEI - 8A - 2A - 10A NC - S - X - NSS
VEI - 8A - 2A - 12 NA - S - NSS
VEI - 8A - 2A - 12 NC - S - X - NSS
VEI - 8A - 2A - 12A NA - S - NSS
VEI - 8A - 2T - 06 NA - S - NSS
VEI - 8A - 2T - 06 NC - S - NSS
VEI-8I-2A-06-NC-SNSS
VEI - 8I - 2A - 06 - NC
- S1 - NSS
VEI-8I-2A-06-NC-S1NSS, N9
S8 - 356
Coils
S8 - 356 2
Manifolds
Preferred
Type
BROC Ident
Manifold
05.99.05.00.09.00.00A
04.94.05.00.56.00.000
OD.13.10.51.30.00.000
OD.13.10.51.40.00.000
OD.13.11.51.30.000
OD.13.20.51.30.00.000
OD.14.40.58.30.00.000
OD.14.32.58.44.00.000
R901096083
R901096086
R901096087
R901109366
R901109830
R901109831
R901109832
R901109837
R901104079
R901109372
R901109867
R901109375
R901109871
R901162013
R901109495
R979015064
R979015065
R979015066
05990500090000A
R901161981
R901126871
R901126872
R901126873
R901126892
R901113693
R901113705
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
OD.15.06.18.1A.S0.000
2/2 poppet directional valve, normally open, both way, common cavity
R901091130
OD.15.05.18.3A.S8.000
2/2 poppet directional valve, normally closed, extra spring, both way, common cavity
R934003080
OD.15.06.17.1A.S0.000
2/2 poppet directional valve, normally open, both way, special cavity
R901113677
OD.15.05.17.3A.S8.000
2/2 poppet directional valve, normally closed extra spring, both way, special cavity
R901119220
OD.15.06.36.1A.S0.000
2/2 poppet directional valve, normally open, both way, common cavity
R901080489
OD.15.05.36.3A.S0.000
2/2 poppet directional valve, normally closed, both way, common cavity
R901090947
X
OD.15.05.36.3A.S8.000
solenoid operate valves, poppet 2 way normally closed, extra spring, common cavity
R901090945
X
R901104409
OD.15.06.21.1A.S0.000
2/2 poppet directional valve, normally open, extra spring, both way, special cavity
OD.15.05.21.3A.S8.000
2/2 poppet directional valve, normally closed, extra spring, both way, special cavity
R901119221
OD.15.06.89.1A.S0.000
OD.15.06.89.1A.S0.001
2/2 poppet directional valve, normally open, both way, common cavity
2/2 poppet directional valve, normally open, both way, common cavity
R901091139
R901091140
OD.15.32.18.1A.S0.000
2/2 poppet directional valve, normally open, double lock, both way, common cavity
R901091171
OD.15.31.18.3A.S0.000
2/2 poppet directional valve, normally closed, double lock, both way, common cavity
R901082015
OD.15.05.18.3I.S0.000
solenoid operated valves, poppet 2-way normally closed, common cavity
R901090953
OD.15.01.18.3I.S0.000
2/2 poppet directional valve, normally closed, one way, common cavity
R901090962
OD.15.01.18.3M.S0.000
solenoid operated valves, poppet 2-way normally closed, common cavity
OD.02.17.01.30.OC.000
OD.02.17.01.30.OB.000
OD.02.17.01.30.OW.000
OD.02.17.01.30.OZ.000
OD.02.17.20.30.OC.000
OD.02.17.20.30.OB.000
OC.10.09.00.40.00.000
coil, 24VDC, Hirschmann
coil, 12VDC, Hirschmann
coil, 110 V RAC
coil, 220 V RAC, Hirschmann
coil, 24VDC, Deutsch connector
coil, 12VDC, Deutsch connector
manifold 2 way aluminum
R901090966
R901083065
R901090821
R901087981
R901085466
R901094611
R901094609
R901082022
X
X
X
X
X
X
X
X
X
X
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es
Cartridge Valves - RC X BROC
BR RC Brazil
BR Oil Control
Cavity Interchange?
Note
Group 01
BRBR Code
Directional
44002803
RCSS2SE8K10M
Group 02
BRBR Code
44005503
Directional
RCEE4WE8K10M
44005803
RCEX2WH8GA10M
44005703
44002603
Group 03
BRBR Code
43048503
43048103
43048403
43052503
43105303
43105503
44005403
Group 04
BRBR Code
43219503
43219603
43219803
43218703
43017603
Group 05
BRBR Code
43018503
43162903
43163403
Group 06
BRBR Code
43218603
43204603
43204703
43204803
43018003
Group 07
BRBR Code
43219003
43219703
43210003
43210103
-----
Valve without consumption
RCEX2WH8K10M
---
---
---
Valve+housing without consumption
RCSC2SE8K10M
---
---
---
Valve without consumption
Flow
RC2FP10KI10M*-SO417565
RC2FP10KI10MA
RC2FP10KI10MB
RC2FP10KI10MC
RC3MK10KE10M
RC3MK10KM10M
RCEB2WE8K10M
Flow
RC2FC8KI10AM
RC2FC8KI10BM
RC2FC8KI10CM
BROC Code
SAP Code
Description
R901095981
04.02.02.04.85.40.000
VRFB-10A
------R901095981
04.02.02.04.85.40.000
VRFB-10A
Pressure
RC1DR10KI10*M-SO41-7564
RC1DR10KI10AM
RC1DR10KI10BM
RC1DR10KI10CM
RC1DR10KI10DM
SAP Code
Description
BROC Code
------------R901109742
04.95.04.03.85.08.000
VRPR-10A
-------------
Isolator - Check
RC1SV8K10AM
RC1SV8K10BM
RC1SV10K10AM
RC1SV10K10BM
BR RC Brazil
RCEC3WH8K10M
RCEC3WH8KI20AM
43217303
43217403
43214703
RCEC3WH8KI20BM
BROC Code
SAP Code
Description
04.33.06.00.56.00.00A
VSON-08A
R901106627
------R901106629
04.33.05.00.85.00.00A
VSON-10A
------BR Oil Control
SAP Code
Description
----R901126871
OD.13.10.51.30.00
R901126872
OD.13.10.51.40.00
--------R979015064
OD.71.01.51.01
R979015065
OD.71.01.51.02
R979015066
OD.71.01.51.04
Valve without consumption
Yes
No
No
Valve without consumption
Valve without consumption
Valve without consumption
Totally adjustable (0 - 30 Lpm)
Valve without consumption
Valve without consumption
Valve without consumption
Yes
Yes
Yes
Yes
Valve without consumption
Yes
Valve without consumption
Valve without consumption
Yes
Valve without consumption
Valve without consumption
Yes
Valve without consumption
No
Valve without consumption
Cavity Interchange?
Note
BROC Code
--VED-8I-32-06-SE
VED-8I-32-06-SE
----VDP-32
VDP-32
VDP-32
Valve without consumption
Yes
Yes
Yes
Yes
Yes
Valve without consumption
Valve without consumption
Switching pressure 03 - 25 Bar
Switching pressure 20 - 60 Bar
Switching pressure 70 - 100 Bar
Directional
RC1AT8K10M VAL. ALTERNADO
BROC Code
SAP Code
Description
R901161981
04.94.05.00.56.00.000
SELB-08A
Pressure
RC1DB10KE10AM
70BAR
RC1DB10KE10BM
RC1DB10KE10CM
RC1DB10KI10AM
70BAR
RC1DB10KI10BM
140BAR
RC1DB10KI10BV
140BAR
SAP Code
Description
BROC Code
------------------------------------R901113622
04.11.56.03.85.10.000
VSBG-10A
R901113624
04.11.56.03.85.20.000
VSBG-10A
R901113626
04.11.56.03.85.35.000
VSBG-10A
Yes
Yes
Yes
Valve without consumption
Valve without consumption
Valve without consumption
Valve without consumption
Valve without consumption
Valve without consumption
Pressure range 35 - 140 Bar
Pressure range 105 - 210 Bar
Pressure range 175 - 350 Bar
BROC Code
SAP Code
Description
R901113622
04.11.56.03.85.10.000
VSBG-10A
R901113624
04.11.56.03.85.20.000
VSBG-10A
R901113626
04.11.56.03.85.35.000
VSBG-10A
No
No
No
Pressure range 35 - 140 Bar
Pressure range 105 - 210 Bar
Pressure range 175 - 350 Bar
VUCN-10A
VUCN-10A
--VUCN-10A
Yes
Yes
Cracking pressure 0,5 Bar
Yes
Valve without consumption
Cracking pressure 5 Bar
VUCN-08A
VUCN-08A
VUCN-08A
Yes
Yes
Yes
Cracking pressure 1 Bar
Cracking pressure 1 Bar
Cracking pressure 5 Bar
--VSBN-10A
Yes
RC1DB10KI10CM
250BAR
Pressure
RC1DB8KI10AM
70BAR
RC1DB8KI10BM
140BAR
RC1DB8KI10CM
250BAR
Isolator - Check
RC1S10K10AM
RET. 0.35BAR
RC1S10K10BM
RET. 1,0BAR
RC1S10K10AV
RET. 0.35BAR
RC1S10K10CM
RET. 4.5BAR
SAP Code
Description
R901106596
04.31.23.00.85.00
R901106596
04.31.23.00.85.00
----R901106601
04.31.23.00.85.05
BROC Code
Isolator - Check
RC1S8K10AM
RET. 0,35BAR
RC1S8K10BM
RET. 1BAR
RC1S8K10CM
RET. 4.5BAR
SAP Code
Description
R901007308
04.31.20.00.56-00
R901007308
04.31.20.00.56-00
R901106550
04.31.20.00.56-05
BROC Code
Pressure
RC3DB10KE10AM
RC3DB10KE10AM SO41-7946
RC3DB10KE10BM
SAP Code
Description
----R901113609
04.11.55.03.85.10
BROC Code
RC3DB10KE10CM
RC3DB10KI10AM
RC3DB10KI10BM
70 BAR
140 BAR
RC3DB10KI10CM
BR RC Brazil
Group 15
BRBR Code
43018203
BROC Code
------VRFD-10
STVU-08A
STVU-08A
---
BROC Code
SAP Code
Description
------------R901106472
04.13.05.03.85.10.000
VSPY-10A
R901106472
04.13.05.03.85.10.000
VSPY-10A
R901109366
OD.21.01.03.56.000
STC-06
44005603
44005903
43167703
SAP Code
Description
------------R901106675
04.04.02.04.85.40.000
R901109368
04.01.02.03.56.00.000
R901109839
04.01.02.04.56.00.000
-----
Flow - Sequence
RC1DZ10KE10AM
RC1DZ10KE10BM
RC1DZ10KE10CM
RC1DZ10KE10DM
RC1F8KM10M
RCEC3WE8K10M
Group 11
BRBR Code
43018103
43217203
43017103
Group 12
BRBR Code
43217903
43214503
43223303
43218003
Group 13
BRBR Code
43041103
43217703
43217803
Group 14
BRBR Code
43167503
43167803
43167603
BROC Code
---
44005303
43214403
Description
simple restraint A to B - 30 L/min
simple restraint A to B - 30 L/min + Manual Ove
---
Directional
RCEC3WE8GA10M/24V
Group 09
BRBR Code
43105403
Group 10
BRBR Code
43167203
43167303
43167403
43217503
43217603
43222203
SAP Code
---
No
No
---
Group 08
BRBR Code
F000530013
44006003
SAP Code
Description
BROC Code
R901090962
OD.15.01.18.3I.S0.000
VEI-8A-2A-06-NC-S1-NSS
R901090966
OD.15.01.18.3M.S0.000
VEI-8I-2A-06-NC-S1-NSS, N9
Pressure
RC3DB8KI10AM
70BAR
43217103
RC3DB8KI10BM
140BAR
43017003
RC3DB8KI10CM
250BAR
Yes
Cracking pressure 0,5 Bar
Valve without consumption
Valve without consumption
R901113609
R901113610
R901115702
----R901113609
R901113610
R901115702
04.11.55.03.85.10
04.11.55.03.85.20
04.11.55.03.85.35
----04.11.55.03.85.10
04.11.55.03.85.20
04.11.55.03.85.35
BR Oil Control
SAP Code
Description
----04.11.49.03.56.10
R901113599
R901097728
04.11.49.03.56.20
R901113599
04.11.49.03.56.10
R901097728
04.11.49.03.56.20
R901091914
04.11.49.03.56.35
VSBN-10A
VSBN-10A
VSBN-10A
----VSBN-10A
VSBN-10A
VSBN-10A
Yes
Yes
Yes
Valve without consumption
Valve without consumption
Yes
Yes
Yes
Cavity Interchange?
Note
BROC Code
--VSBN-08A
VSBN-08A
VSBN-08A
VSBN-08A
VSBN-08A
Valve without consumption
Yes
Yes
Yes
Yes
Yes
Comercial Andaluza de Técnicas y Suministros, S.L. (CATS, S.L.) Málaga (España). Telf: +(34) 952 24 61 37 www.cats.es comercial@cats.es