E:\C-DATA\外发资料\EOC用户手册\EOC outdoor Master User Manual

EOC Outdoor Master User Manual
Catalogue
1
Introduction...........................................................................................................................................................2
1.1 Application.................................................................................................................................................... 2
1.2 Commitment..................................................................................................................................................2
1.3 Packing List...................................................................................................................................................2
2
Installation preparation......................................................................................................................................... 3
2.1 Product Drawing...........................................................................................................................................3
2.2 Description of LED.......................................................................................................................................3
2.3 Description of Interface............................................................................................................................... 3
2.4 Functional Feature........................................................................................................................................4
2.5 Installation environment..............................................................................................................................4
2.6 Steps of installation.......................................................................................................................................4
2.7 Network diagram..........................................................................................................................................5
2.8 Frequency Question Answer....................................................................................................................... 5
2.9Attention......................................................................................................................................................... 6
3
Equipment test...................................................................................................................................................... 7
3.1 Web configuration........................................................................................................................................ 7
3.2 CLI configuration......................................................................................................................................... 7
Appendix one: Disclosure Table...................................................................................................................................9
1
1 Introduction
Thanks for using our EOC Master!
EOC Master is an Ethernet access equipment design for solving Two-way Reconstruction in CATV
Network. Its uplink port connects to IP Port and downlink mix CATV signal to deliver TV
program and IP data. We offer diversified and customized service to you.
It’s very easy to install EOC Master so you can finish the configuration according to this user’s
manual. Before using our equipment, please read this book.
1.1 Application
The user manual will help you to know and use EOC Master correctly.
1.2 Commitment
Equipment mentioned in this manual refers to EOC Master without special description.
1.3 Packing List
One packing box includes:
 One EOC master
 One user manual
 One Quality Passed Certificate
2
2 Installation preparation
2.1 Product Drawing
2-1 schematic diagram
2.2 Description of LED
Item
Label
Power Indicator
POWER
Ethernet
ETHERNET
System Indicator
SYSTEM
Indication
of
PLC
linking and action
LINK
Action
Description
off
Without electricity
on
OK
on
Physical link
off
Physical link is OK
off
System doesn’t start
on
System starts
off
Coaxial cable is not connected
or connect in a wrong way
on
Coaxial cable connect correctly
not connected
2.3 Model
Product
name
int6400
Series
Model
Description
CD6101
1RF Input,1 Data Input,1COM Output Master, Outdoor type
CD6101-F1
1RF Input,1 Data Input,1COM Output ,1 Fiber Optic Media
Converter ,Master, Outdoor type
CD6112
2RF Input,2 Data Input,2COM Output Master, Outdoor type
CD6114
4RF Input,2 Data Input,4COM Output Master, Outdoor type
CD6611
1RF Input,1 Data Input,1COM Output ,1ONU,Master, Outdoor type
CD6622
2RF Input,2 Data Input,2COM Output,1ONU, Master, Outdoor type
CD6624
4RF Input,2 Data Input,4COM Output,1ONU, Master, Outdoor type
CD7101
1RF Input,1 Data Input,1COM Output Master, Outdoor type
3
int7410
Series
CD7101-F1
1RF Input,1 Data Input,1COM Output ,1 Fiber Optic Media
Converter ,Master, Outdoor type
CD7112
2RF Input,2 Data Input,2COM Output Master, Outdoor type
CD7114
4RF Input,2 Data Input,4COM Output Master, Outdoor type
CD7611
1RF Input,1 Data Input,1COM Output ,1ONU,Master, Outdoor type
CD7622
2RF Input,2 Data Input,2COM Output,1ONU, Master, Outdoor type
CD7624
4RF Input,2 Data Input,4COM Output,1ONU, Master, Outdoor type
Note: Product you get depends on goods
2.4 Functional Feature
 Support tree-type and star-type CATV network.
 Built-in isolation filter with high functionality.
 Support user to log in through Web interface to centralize management on the EOC
slaves under the master, including VLAN configuration, QoS configuration, port
management, log in permission management, status information inquiry and update
software.
 Support user to log in EOC Master through Console Port,Telnet and configured it.
 Support EMS network management.
2.5 Installation environment
Requirements:
 Far away from heat emitted devices
Suitable environment:
 Temperature: -20℃~50℃
 Humidity: 10﹪~90﹪(Non condensing)
2.6 Steps of installation
Please install EOC Master as follows:
⑴ Set up WAN link
Link the cable to LAN. You also can connect the equipment with PC in order to configure EOC
Master and manage network.
⑵ Connect CATV network
Please connect CATV signal to master’s F-connector (CATV INPUT) via coax cable and the other
F-connector marked as CABLE combine the CATV and data signal output to the distribution
networking ,finally accessing to the EOC Slave in the subscriber end.
⑶ power supply requirement
If equipment has electricity, it will start to work automatically.
You can link equipment as follows:
4
2-2 Connection Figure
(4)Notice
 Each equipment connects to RF port with coaxial cable. Please do not touch the cable’s
manual connector in case of any interference in communication quality.
 Circumscribed repeater or bridge unit should be put besides Amplifier.
 If the high level output signal from the EOC master is not filtered well ,it may has impact
on the catv channel .In this case ,please add a high passing filter on the catv link to isolate the
eoc signal totally .
2.7 Network diagram
2-3 Network diagram
2.8 Frequent Question and Answer
 Power light does not shine
1) Check if the power adapter works well.
2) Check if the power connector is corrected
 System light does not shine
1) Use millimeters to check whether 220V/60V input is correct. If not, please change
another power adapter.
2) Check whether IP is connecting. If yes, maybe there is something wrong with
Ethernet LED.
5
 Ethernet light does not shine
1) Check the validity of the cable connections; check whether the master panel's
indicator light flashing; and check whether cable is working.
2) Check if cable connects to equipment.
 Cable light does not shine.
1) Maybe there is no user access.
2) If there are user access, please press reboot button.
3) Check whether Master is correct. If yes, it means the cable light has something wrong. But it
won’t influence machine’s working.
 When there is no data signal input to distribution networking node, EOC Slave CABLE
LED is off or flashing.
1) Disconnect the link and check if the link attenuation is within 60dB,or check if
digital /analog TV is working normally. If not, please maintain the coax cable link.
2) CABLE LED is flashing, indicating there is too much interference .Please check
the coax cable networking construction is standard or not .If there is too messy; please
maintain the coax cable link.
3) The electric amplifier doesn’t connect with the bridge .If so ,please connect the
bridge to the amplifier .
2.9Attention
There is something to be mentioned when you use it:
 All Installation and adjustment must follow user’s manual.
 Pay attention to all alarm mark.
 Avoid small metal component entering into equipment.
 Please switch off the power when it’s not used for a long time.
 If there is something wrong with the equipment, please contact with professional
engineers for instruction.
 Avoid putting equipment in aisle or other places where is crowded with residents.
 Check if ground connection is done well.
6
3 Equipment test
3.1 Web configuration
Input IP (LAN IP :192.168.2.2)of EOC equipment in IE explorer and write down username and
password (admin/admin). You will see following interface:
7
3-1 Web management
You can configure IP, VLAN, and QOS in Web interface. If there is any problem, please contact
with our technology staff.
3.2 CLI configuration
Click “start”-Enter telnet IP
Enter user’s name and password (admin/admin), and then you can start to configure equipment.
3-2 CLI management
You can set IP, VLAN and QOS by CLI. If you have any problem, please contract our technology
staff.
8
Appendix one: Disclosure Table
Parts
Hazardous Substance
Cd
Cr6+
PBB
Pb
Hg
PBDE
Placode

○
○
○
○
○
Plastic element
○
○
○
○
○
○
Metal element
○
○
○
○
○
○
Packaging material
○
○
○
○
○
○
Accessory
○
○
○
○
○
○
○: Indicates that this toxic or hazardous substance contained in all the homogeneous material, is below the
limit requirement of SJ/T11363-2006.
: Indicates that his toxic or hazardous substance contained in all the homogeneous material fort is beyond
the limit requirement of SJ/T11363-2006.
9