UV Sterilizer Instruction Manual Includes: Classic

Add to my manuals
32 Pages

advertisement

UV Sterilizer Instruction Manual Includes: Classic | Manualzz

42371 Avenida Alvarado

Temecula, CA 92590

TOLL FREE (800) 454-2725

TEL (951) 296-3480

FAX (951) 296-3490 www.aquauv.com

UV Sterilizer Instruction Manual Includes:

Classic Series

Twist Series

8/15 Watt

25/57 Watt

40 Watt

SEE INSIDE COVER FOR LARGER UNITS

TABLE OF CONTENTS

Classic / Twist Model Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Classic / Twist Wiper Model Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1

2

3

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4

6

How Ultraviolet Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fresh Water Sizing Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6

7

Salt Water Sizing Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8

Recommended Layouts 9

Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation Instructions

Trouble Shooting Leaks

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the Lamp for Single Lamp Units

10

11

14

16

Winterizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18

Maintenance Lamp Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19

Cleaning or Changing the Quartz Sleeve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20

21

22

23

Part List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Incorrect Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25

27

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

CLASSIC SERIES

8/15 Watt

25 Watt

57 Watt

40 Watt

1

TWIST SERIES

25 Watt

40 Watt

57 Watt

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

8/15 Watt

25 Watt

CLASSIC WIPER SERIES

57 Watt

40 Watt

25 Watt 57 Watt

TWIST WIPER SERIES

40 Watt

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

2

THANK YOU FOR PURCHASING THE BEST ULTRAVIOLET SYSTEM

IMPORTANT INFORMATION

WE CAN HELP YOU

R

eturning this product is expensive and time consuming for you, your retailer and for us,

the manufacturer. Should you encounter any problems with your product,

please call our toll free “HELP” line for assistance 1-800-454-2725.

PLEASE DO NOT return your product to the store! Your dealer or distributor cannot offer any warranty work or exchanges.

3

In the US please call

TOLL FREE 1-800-454-2725

(951) 296-3480 Outside the U.S.

THANK YOU!

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

WARRANTY INFORMATION

Aqua Ultraviolet systems are warranted against failure due to defects in materials and/or workmanship during the warranty period. This warranty covers defects occurring under normal use and applies to the original retail purchaser and may not be transferred. The warranty and remedies set forth herein are conditional upon proper storage, installation, use, maintenance and conformance with the applicable use. It will be based upon Aqua Ultraviolet’s discretion as to whether the defects are of manufacturing origin.

This warranty does not apply to appearance or accessory items. This warranty does not include damage due to shipping and handling, transportation, unpacking, set up, installation, improper maintenance, incorrect line voltage, modification, abuse, misuse, neglect, accident, fire, flood, acts of God or repair or replacement of parts supplied by any other than

Aqua Ultraviolet.

Any oral statements about this product made by the seller, the manufacturer, their representatives or any other party does not constitute warranties and shall not be relied upon by the user and are not part of this contract.

Neither the seller nor the manufacturer shall be liable for any injury, loss or damages, direct, incidental or consequential including but not limited to lost profits, lost sales, injury, inability to use the product and the user agrees that no other remedy is available.

Before installing, the user shall determine the suitability of the product for their intended use and the user shall assume all risk liability whatsoever in connection therewith.

To validate this warranty, mail the enclosed warranty card within 10 days of purchase along with proof of purchase (copy of sales receipt).

Warranty Period:

Housing: Limited lifetime warranty on housing against Ultraviolet degradation.

Complete Unit: One year from the date of purchase or 18 months from manufacturing date.

Limitations:

Warranty does not cover any malfunction from improper installation (we recommend that a licensed

electrician install your system to the specifications outlined in this owners guide).

Warranty only applies to the original end user and is not transferable.

Warranty does not cover repairs done by anyone other than Aqua Ultraviolet.

Warranty is void if system is not plugged into a G.F.C.I. (Ground Fault Current Interrupter).

Warranty may not be modified by verbal statements by Aqua Ultraviolet, distributors, retailers, their

agents or any other party.

Warranty covers the repair or prorated replacement of the Aqua Ultraviolet products. Aqua Ultraviolet

denies all liability for any other loss including but not limited to loss of equipment, income, livestock

or personal injury.

There is no warranty on the Quartz Sleeve.

There are no warranties on broken Lamps. Lamps are prorated by usage.

Warranty is voided by the following:

Product labels defaced or removed.

Housing has been painted.

Product is improperly installed or maintained by user or agent.

Product abused, misused or damaged by user or their agent.

Product damage caused by electrical surges, electrical spikes, electrical brown outs or

improper voltage.

Electrical cord has been cut.

Unit was run without water.

Any implied warranty granted under state law including warranties of merchantability or fitness for a particular purpose are limited to one year from the date of purchase or 18 months from the date of manufacture or as otherwise stated in the above warranty. Aqua Ultraviolet is not responsible for direct, indirect, incidental or consequential damages. Some states do not allow limitations on how long an implied warranty lasts and/or does not allow the exclusions or limitations of incidental damages so the above limitation and exclusion may not apply to you. This warranty gives you special legal rights and you may also have other rights that vary from state to state.

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

4

WARRANTY CONTINUED

Warranty Returns or Repair Returns:

Please call Aqua Ultraviolet at (800) 454-2725 for a “Return Merchandise Authorization” (RMA) number. You must have a valid RMA from an Aqua Ultraviolet customer service representative before sending any product in for warranty or repair. Please have your serial number, date of purchase and product type available when calling for an RMA number.

All warranty returns or repair returns must come freight prepaid with an RMA number clearly marked on the outside of the box. All other returns will be refused. Aqua Ultraviolet will not be liable for any shipping cost to return warranty or repair items. Include a note in the box with your RMA number, name, address, daytime phone number and brief description of the reason for return or repair.

Be sure to return product in the same packing or similar packing and insure the package (we recommend sending it UPS). If you do not have or can’t locate proper packaging, please call our customer service department and we will send you packaging for a minimal charge.

Aqua Ultraviolet shall not be responsible for damage or loss done by the shipper. Nor shall Aqua Ultraviolet be responsible for merchandise that arrives damaged due to improper packaging. All claims for loss and damage must be filed by the customer with the shipper.

If the unit is found to be out of warranty we will contact you with the cost of repair. Your authorization is required prior to making any repairs.

5

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

INTRODUCTION

We at Aqua Ultraviolet would like to take the time to thank you for purchasing the finest Ultraviolet

System on the market.

For over thirty years, Aqua Ultraviolet has manufactured Ultraviolet Systems used in various industries, including aquaculture, public and commercial aquariums, educational institutions, government agencies and research organizations throughout the world.

Aqua Ultraviolet Sterilizers are used as a control to destroy single celled organisms, water borne bacteria, viruses, algae, fungi and protozoa. Aqua Ultraviolet sterilizers are recommended for both fresh and salt water systems as well as ponds. There are no residual effects when using an Aqua Ultraviolet Sterilizer. Ultraviolet will not affect Bio-filters or lower fish immune systems!

HOW ULTRAVIOLET WORKS

The Ultraviolet Lamp emits a germicidal ray which alters or disrupts the DNA or RNA of single celled organisms such as algae, bacteria and protozoa. By properly implementing an Aqua Ultraviolet System in-line, these organisms can be eradicated effectively without any harmful residuals.

Your Aqua Ultraviolet System was made to work as a control for green water and single celled organisms.

This unit will not, nor will any other unit, completely sterilize your pond as the pond itself is not a sterile environment. As a control, this unit will effectively lower your water's bacterial count allowing your fish to stay healthier with less risk of disease.

The Aqua Ultraviolet Sterilizer works better on filtered water. Any debris in the water can inhibit UV

Transmission.

CAUTION: READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION OR

OPERATION.

The manual should answer most of the questions that you may have about the installation, operation and use of your new Aqua Ultraviolet Sterilizer. View our installation videos at www.aquauv.com. If you need technical support, we offer this service for free by telephone (800) 454-2725, or by fax (951) 296-3490 M-F

8:00 am - 4:30 pm Pacific Standard time except selected holidays. You may reach us through the web www.aquauv.com or at [email protected].

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

6

FRESH WATER UV SIZING CHART

Classic UV Units

Classic 8 Watt

Classic 15 Watt

Classic 25 Watt

Classic 40 Watt

Classic 57 Watt

Classic 80 Watt

Classic 114 Watt

Classic 120 Watt

Classic 160 Watt

Classic 200 Watt

Classic 240 Watt

Twist Unit

Twist 25 Watt

Twist 40 Watt

Twist 57 Watt

Size Fresh Water

Sterilizer* in Gallons

5 - 200

200 - 500

500 - 1,200

1,200 - 2,000

1,500 - 3,000

2,200 - 4,400

2,200 - 4,400

4,400 - 6,000

6,000 - 8,500

8,500 - 13,000

13,000 - 17,000

30,000

µw/cm²

(EOL)

GPH

642

700

1,200

2,900

3,200

3,678

3,900

4,080

5,400

6,600

7,200

500 - 1,200

1,200 - 2,000

1,500 - 3,000

1,200

2,900

3,200

Fresh Water

Pond Clarifier***

Gallons

Max Flow

GPH

1,500 1,000

2,000

4,000

6,000

6,500

9,000

9,500

12,000

16,000

20,000

25,000

1,800

2,000

3,000

3,250

4,500

4,500

6,500

9,000

10,000

12,000

4,000

6,000

6,500

2,000

3,000

3,250

* Use the sterilizer column for crystal clear water and bacterial control, in pond and aquarium environments.

*** Use the clarifier column when the pond is partially in the shade and has 50% plant coverage. This will

improve water clarity resulting in a natural looking pond.

GPH numbers are based on turning over the volume of water one time every hour to every hour and a half.

UV dosage is calculated at the end of lamp life (14 months).

Flow rates and results may vary

EZ Twist Cap

Quick and Easy

Quartz Sleeve

Maintenance

Quick Release Tee

Quick Release and

Easy Install of Unit

Optional Wiper

Cleans Quartz Sleeve

Optimizes Transmission l l

Clear Quartz Cap

Glow Tells You

Your Lamp is On l l

Lamp

Longest Lamp Life on the Market,

14 Months l l l

Quartz Sleeve

Allows for a 99.9%

Transmission Rate.

Highest Quality

Hard Quartz

Serial Number

Find the Serial Number on the Silver Warning Label.

Larger Units the Label is on the Transformer Box.

7

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

SALT WATER UV SIZING CHART

Classic 8 Watt

Classic 15 Watt

Classic 25 Watt

Classic 40 Watt

Classic 57 Watt

Classic 80 Watt

Classic 114 Watt

Classic 120 Watt

Classic 160 Watt

Classic 200 Watt

Classic 240 Watt

Twist Units

Twist 25 Watt

Twist 40 Watt

**Salt

Water

Tank

Gallons

355

600

700

900

70

75

150

325

1200

1500

1800

30,000

µw/cm²

(EOL)

GPH

642

700

1,200

2,900

3,200

3,678

3,900

4,080

5,400

6,600

7,200

45,000

µw/cm²

(EOL)

GPH

428

466

800

1,930

2,133

2,452

2,600

2,720

3,600

4,400

4,800

60,000

µw/cm²

(EOL)

GPH

321

350

600

1,450

1,600

1,839

1,950

2,040

2,700

3,300

3,600

75,000

µw/cm²

(EOL)

GPH

256

280

480

1,160

1,280

1,471

1,560

1,632

2,160

2,640

2,880

90,000

µw/cm²

(EOL)

GPH

1,066

1,226

1,300

1,360

214

233

400

967

1,800

2,200

2,400

150

325

355

1,200

2,900

3,200

800

1,930

2,133

600

1,450

1,600

480

1,160

1,280

400

967

1,066

Reef Tanks: A UV Rated in the 30,000 to 45,000 columns is ideal for the reef environment. UV’s rated at higher

kill rates will destroy the planktonic food supply for the reef.

Marine Fish Tanks (No reef or Live Rock): A UV rated in the 75,000 to 90,000 columns will be the most

effective at controlling fish disease.

All UV dosages are calculated at the end of lamp life (14 months).

Flow rates and results may vary

EZ Twist Cap

Quick and Easy

Quartz Sleeve

Maintenance

Quick Release Tee

Quick Release and

Easy Install of Unit

Optional Wiper

Cleans Quartz Sleeve

Optimizes Transmission l l

Clear Quartz Cap

Glow Tells You

Your Lamp is On l l

Lamp

Longest Lamp Life on the Market,

14 Months l l l

Quartz Sleeve

Allows for a 99.9%

Transmission Rate.

Highest Quality

Hard Quartz

Serial Number

Find the Serial Number on the Silver Warning Label.

Larger Units the Label is on the Transformer Box.

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

8

RECOMMENDED POND LAYOUTS

Pick up is too close to return.

RECOMMENDED AQUARIUM LAYOUT

9

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

FREQUENTLY ASKED QUESTIONS

Where do I install my UV?

The best place to install your Aqua Ultraviolet Sterilizer is after the filter. If an after the filter installation is not feasible, your sterilizer can be installed before the filter, but it will take a little longer to work. If installed before the filter, be aware that a small rock passing from the pump can break the quartz sleeve. It is recommended that if you install your unit before your filter, you check the UV periodically for any water leakage due to a broken quartz sleeve. Be sure to have adequate pre-filtration to prevent breakage. (A broken quartz sleeve and any damage caused by a broken quartz sleeve is not covered under warranty.)

Do I have to turn my UV off when I clean my filter?

Yes, but only if the chamber is drained or if the water will remain at a stand still for more than 30 minutes. Note: Running longer than the recommended time without water flow can cause extensive damage to the unit that is not covered under warranty.

What should I expect after my UV is installed?

If your Aqua Ultraviolet system is installed after the filter and is properly sized the water should be clear in 3-5 days. If your Aqua Ultraviolet system is installed before the filter the water should be clear in 7-10 days. The green algae on the sides and bottom of the pond will not disappear, this is normal in a pond. The UV does not control this type of algae.

What’s the difference between a sterilizer and a clarifier?

As a sterilizer, your Aqua UV system will keep your pond or aquarium water crystal clear, plus you will have the added benefit of bacterial control which will help keep your fish healthy and happy with less risk of disease.

As a clarifier the algae in your pond will be reduced, your pond will still have a green tint to it, unless you have 50-75% plant coverage or your pond is in full shade.

Do I install my UV vertically or horizontally?

You can install it either way - (see Installation Instructions Page 11 and 12)

What should my flow rate be on my pond or fresh water aquarium?

The optimum flow rate on your pond or fresh water aquarium is to turn over the volume of water one time every hour to every hour and a half.

What should my flow rate be on my salt water aquarium?

Your flow rate should be 3 to 5 times the volume of water per hour.

Should I bypass part of my water through the UV and the rest back to the water supply?

No, Our UV’s are specifically designed to handle high flow rates for easier installation and the best water quality.

Is this unit submersible?

No, not this specific series.

Does the UV light have any residual effect to the fish?

UV only affects what passes through the chamber. There is no residual effect from UV light.

Does the UV kill good bacteria?

Ultraviolet light does not discriminate about what it destroys. If good bacteria passes by the light it will be destroyed.

Beneficial bacteria are colonized in your filter and along the sides and bottom of your pond. The only time those will be affected is if it becomes free floating and passes through the UV.

How often should I change my lamp?

The lamp should be changed after 14 months of continuous use.

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

10

CLASSIC INSTALLATION INSTRUCTIONS

NOTE: All units are quality tested from the factory. All units are rated up to 50 PSI.

Mount your Aqua Ultraviolet Sterilizer horizontally or vertically on a wall or above ground, on a level and firm surface. Do not lay the system on the ground or where water may puddle. Your Sterilizer should be easily accessible. Do not submerge.

On units with the Wiper option remember to allow enough space to pull the Wiper Rod all the way out.

On all units allow space to change the Lamp and Quartz Sleeve.

Horizontal Installation is preferred since the chamber is more likely to remain flooded with water.

8, 15, 25, 40, 57 Watt Units:

Wiper Option

On Wiper Option UV’s water should flow into the unit through the opening nearest the end with the wiper ball.

This will help ensure that the chamber stays full and the Wiper Rod will not push out.

80, 120 Watt Units: Wiper Option

Water Flow Out

Water Flow In

Plumb the water going in from the bottom and out through the top. This will help ensure the chamber stays full of water.

160, 200, 240 Watt Units:

Inlet / Outlet ports should be facing upward.

Wiper Option

The above are suggestions, if these are inconvenient, either port can be used as the inlet or the outlet.

In any installation the pump must be of a sufficient power to keep the chamber full of water so the seals around the wiper nut do not dry out.

Note: If the Wiper Nut Seal is exposed to air or to the lamp it will dry out, crack and leak. This is not covered under warranty.

11

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

CLASSIC INSTALLATION INSTRUCTIONS

Vertical Installation

Be careful not to drop the lamp down inside the unit, this can break the Quartz Sleeve. The Quartz

Sleeve is not warranted against breakage nor is any damage caused as a result of a broken Quartz

Sleeve. (SEE ILLUSTRATION ON PAGE 27.) In a vertical installation Wiper Units should be installed with the wiper portion facing downward.

8, 15, 25, 40, 57 Watt Units:

Wiper Option

Water Flow Out

Water Flow Out

Water Flow In Water Flow In

200, 120 Watt Units:

Plumb the water going in from the bottom and out through the top. This will help ensure the chamber

stays full of water.

Wiper Option

Water Flow Out

Water Flow Out

Water Flow In Water Flow In

80,160, 240 Watt Units:

Water Flow In

Water Flow Out

Wiper Option

Water Flow In

Water Flow Out

The above are suggestions, if these are inconvenient, either port can be used as the inlet or the outlet. In any installation the pump must be of sufficient power to keep the chambers full of water so the seals around the Wiper Nut do not dry out.

Note: If the Wiper Nut Seal is exposed to air or to the lamp it will dry out, crack and leak. This is not covered under warranty.

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

12

CLASSIC INSTALLATION INSTRUCTIONS

1. You can use mounting brackets (A40124 that can be purchased from us) or plumber’s straps to

attach your unit to a wall or firm surface.

CAUTION: Your Aqua Ultraviolet unit is not submersible. If this unit falls into the water, turn main

power off and then retrieve it. Do not attempt to use this sterilizer if it has been submerged. Do

not operate this unit if it has a damaged cord or plug, if it is malfunctioning or if it has been

dropped or been damaged in any manner.

2. The UV should be installed after the filter on the return line. This helps ensure that the water is

clear of debris and impurities that could inhibit the disinfection process. The UV can be installed

before the filter, however, it will take longer to work. Note: You increase the risk of breakage to

the Quartz Sleeve and Lamp should debris enter the UV unit when installed before your filter.

For 3/4” threaded units: a. Locate the barbs included with your

unit. Barbs are fitted for either 3⁄4” or

1⁄2” hose (see illustration).

1/2” Barb

Cut here on line with hacksaw to make 3/4”

Barb

3/4” Barb b. The barbs have been Teflon taped for

you to prevent leakage. Install barbs,

hose and hose clamps. (Hose and

hose clamps are not included.)

For 2” slip fitted units:

8, 15, 25, 40, 57 Watt Units glue existing pipe

into the unions provided on unit.

Customers

Existing Pipe

For 2” and 3” Slip Fitted Units:

80, 114, 120, 160, 200, 240 cut 2 pieces of sch 40

2” PVC pipe to the length of 2-3/8” (supplied by

customer). This pipe is used to attach the UV

sterilizer to the unions that were provided.

Use only PVC glue and primer.

2” Union

SCH 40 2” PVC Pipe

Supplied by Customer

For 80-240 Watt Units

80 Watt

3. Based on your personal plumbing configuration, additional plumbing supplies may be needed.

4. Make sure the unit is mounted securely before operating.

LEAK TEST: Do not install the Lamp or electrical components yet. After all connections have been

made, turn on the pump and run for five minutes to check for leaks.

a. If there are no leaks, turn pump off and continue installing the lamp (on page 15).

For units 8,15, 25, 57 and 114 watt. For 80 watt and 120- 240 watt continue to electrical

installation on page 16.

13 b. If unit leaks turn pump off and continue to troubleshooting leaks on page 14.

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

Leak

Quartz Cap

TROUBLE SHOOTING LEAKS

Leaks from Quartz Cap / Rubber Seal

Undo Quartz Cap and push Rubber Seal into the Sterilizer body evenly. Half of the

Rubber Seal will still be in view. Screw on the Quartz Cap and finger tighten. Do not use a pipe wrench, pliers or any other tool. Hand-tighten only. Do not use any lubricant.

EZ Twist Top

Leak

Leaks from the EZ – Twist Top

Check that the O-ring is in the EZ-Twist Top.

Hand tighten EZ-Twist Top until leak stops.

Do not use any lubricant.

EZ Twist Top

Quartz Cap

EZ Twist Top

Quartz Cap

Twist Union

Wiper Nut

Wiper Nut

Wiper Rod

Leaks from Center of Quartz Sleeve

The Quartz Sleeve is broken and needs to be replaced. Neither the broken Quartz

Sleeve nor any damage caused as a result of a broken Quartz Sleeve is covered under warranty. Contact your dealer for a replacement. (See Replacing the Quartz

Sleeve on page 22).

Leaks from the Twist Union

Check that the O-ring is in the Twist Union. Hand tighten union until leak stops. Do not use any lubricant.

Leak

Base of Unit

Base of Unit

Leaks from outside the Wiper Nut

I f you notice a leak between the base of the unit and the nut, the Wiper Nut may need more teflon tape for a tighter seal. If the leak persists, please contact our customer service department at 1-800-454-2725 for assistance.

Leaks from the Wiper Rod

If you notice a leak between the Wiper Nut and the Wiper Rod, the seal may be cracked or damaged. If this occurs, please contact our customer service department at

1-800-454-2725 for assistance.

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

14

INSTALLING THE LAMP

For 8, 15, 25, 40, 57 and 114 Watt Units

NOTE: If you touch the Lamp use denatured alcohol and a soft cloth to clean the Lamp. If you do not clean the Lamp the fingerprints will become etched into the glass which will diminish

UV output and may cause premature lamp failure.

NOTE: Lamps and Quartz Sleeves should be handled with care. Lamps and Quartz Sleeves are not warranted against breakage or damage.

WARNING: Do not install the Lamp at an angle (even a slight angle); this may cause a U shaped crack at the end of the Quartz Sleeve, or possible breakage of the Lamp. If this should happen, do not proceed with the installation. Purchase a new Quartz Sleeve or Lamp from your dealer and refer to the proper installation instructions.

NOTE: Do not force the Lamp into the Quartz Sleeve.

1.

Unscrew the Davis Connector located behind the Transformer

Cap, this allows your Transformer Cap to spin freely.

Transformer Cap

Davis Connector Lamp End Connector

2. Plug the Lamp flush into the Lamp End Connector before inserting the Lamp into the unit.

If the Lamp is not plugged in all the way it may cause damage to the unit and is not covered

under warranty .

3. Insert the Lamp straight into the Quartz Sleeve. Be careful, inserting the Lamp at an angle, even

a slight angle, can cause a "U" shaped crack in the Quartz Sleeve.

Screw on

Transformer Cap

4. Twist the Transformer Cap onto the

Quartz Cap. Do not over tighten.

This is a connection only and is not

in contact with water.

Screw on

Davis Connector Quartz Cap

5.

Tighten the Davis Connector back on to the

Transformer Cap.

6.

FINAL LEAK CHECK: Do not plug the Sterilizer into power yet, turn on the pump, let water run for

5 minutes and check for leaks. (See page 14 for trouble shooting leaks).

7. Once a leak test is completed, and there are no leaks, plug the Transformer into a GFCI outlet.

15

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

ELECTRICAL INSTALLATION

For 80, 120, 160, 200, 240 Watt Units

1. Cover Removal: Remove the cover from the Transformer Box to allow access to screw holes

located on the back panel of the box. The cover slides down.

2. Mounting: Mount the Transformer vertically on to a wall or other sturdy surface a minimum of 4

feet away from any dwelling. Make sure the Transformer is close enough to attach to the

UV unit.

Cover Open

Cover Closed

G.F.C.I

Temecula, CA, USA

SERIAL NO.

MANUF. #

SL400

240W

A15

8W

SL800

S100

80W

15W

SL1200

S200

114W

25W

S300

120W

40W

SL100

160W

57W

SL200

200W

A8

THE INDICATED WATTAGE SIZE. AC ONLY. MAXIMUM RATING OF 50 PSI

SUPPLY BEFORE RELAMPING. CAUTION: RISK OF FIRE USE ONLY AQUA ULTRAVIOLET LAMPS IN

INTERRUPTER(GFCI) CAUTION: R ISK OF E LECTRICAL SHOCK. D ISCONNECT F ROM P OWER

CONNECT O NLY T O A C IRCUIT T HAT I S P ROTECTED B Y A G ROUND-FAULT C IRCUIT

DAMP LOCATIONS. DO NOT SUBMERGE IN WATER. WARNING:RISK OF ELECTRICAL SHOCK.

SKIN WILL NOT BE SUBJECTED TO INJURIOUS RAYS. SUITABLE FOR INDOOR, OUTDOOR, AND

COMPLIANCE WITH COMPETENT TECHNICAL DIRECTION SO THAT THE USERS EYES ANDBARE

THIS FIXTURE IS DESIGNED FOR USE WITH GERMICIDAL LAMPS AND MUST BE INSTALLED IN

WARNING

3. 220V Transformer: Must be hard wired into a dedicated line of the appropriate voltage and

hertz.

4. 110V Transformer: Plug into 3 prong G.F.C.I. Outlet.

MULTI LAMP UNITS ELECTRICAL INSTALLATION

1. DISCONNECT THE HUBL CONNECTOR: Unscrew the Hubl Connector located just above the

Transformer Cap. This will allow the transformer cap to turn without kinking the harness.

Hubl Connector

Un screw Ca p

Transformer Cap

2. CONNECT THE LAMP: Plug a Lamp into each of the Lamp End Connectors, located at the end of the harness, one at a time. Make sure the Lamps are plugged in all the way flush with the Lamp End

Connectors. If the Lamps are not plugged in all the way it may cause damage to the unit and is not cover under warranty.

3. Insert the Lamp straight into the Quartz Sleeve. Be careful, inserting the Lamp at an angle, even a slight angle, can cause a “U” shaped crack in the Quartz Sleeve. Insert one lamp at a time.

16

MULTI LAMP UNITS ELECTRICAL INSTALLATION

4. CONNECT THE TRANSFORMER CAP: Twist the Transformer Cap onto the Quartz Cap. Do not over

tighten. This is a connection only and is not in contact with water so it does not have to be tight. Do

not use a pipe wrench, pliers or any other tool.

Transformer Cap Quartz Cap

5. Tighten the Hubl Connector back onto the transformer cap.

Hubl Connector

Repeat to install each lamp.

6. FINAL LEAK CHECK: Do not plug the sterilizer into power yet, turn on pump and check for leaks

again. For illustrations, SEE PAGE 14. a. If there are no leaks, continue with electrical installation turn power on to UV.

b. If you have a leak, return to Trouble Shooting Leaks on page 14. Carefully examine this unit

after installation. This unit should not be connected to electricity if there are any leaks.

CAUTION: Do not look at or handle UV Lamps when lit outside of the housing. Considerable

Ultraviolet energy is emitted which may produce severe sunburn and/or conjunctivitis. As long as the

UV light is in its housing it is 100% safe for humans and fish.

NOTE: The average life expectancy of Aqua Ultraviolet Lamps is 14 months of continuous

WARNING: If you are using any medication, we recommend shutting down the sterilizer as the

UV Radiation may affect the treatment.

CAUTION: Do not use the Aqua Ultraviolet Sterilizer for anything other than its intended use.

17

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

WINTERIZING

CAUTION: Always turn off the pump and disconnect electricity from the unit prior to any maintenance.

Option 1: If you are going to continually run water through your unit and it will be exposed to

freezing temperatures be sure to install winterizing caps (sold separately) on the unit and take all

the internal parts inside (Quartz Sleeve, EZ-Twist Top, Quartz Cap, Lamps, Rubber Seals, and

Small Transformers. NEMA Transformer Boxes may be left outside.

Take these parts inside

Quartz Cap

EZ Twist

O-ring

Quartz Sleeve

EZ Twist

Top

Rubber Seal

Lamp

TM

Lamp

Transformer

Option 2: If you are not flowing water through your system, use a winterizing cap, drain the unit

completely and take the internal parts inside. If the unit is not completely drained, the water will

freeze and crack the housing. This is not covered under warranty.

Option 3: If you don't have a winterizing cap and are not going to run water through the

system, remove the Lamp, disconnect unions and take the Sterilizer inside.

Store the Lamp separately to avoid breakage.

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

18

MAINTENANCE

CAUTION: Always turn off the pump and disconnect electricity from the unit prior to any maintenance.

Changing the Lamp.

Transformer Cap

Davis Connector

TM

Quartz Cap

Lamp

Lamp End Connector

1. Unplug the UV from the power source and turn off the pump.

2. Unscrew the Davis or Hubl Connector located

behind the Transformer Cap, this allows

your Transformer Cap to spin freely.

Unscrew Davis Connector

Unscrew Transformer Cap

3. Twist off the Transformer Cap.

4. Slide Lamp out, be careful not to slide the Lamp out at an angle, even a slight angle, this

may cause a “U” shaped crack at the end of the Quartz Sleeve, or possible breakage

of the Lamp. A Broken Lamp or Quartz Sleeve are not covered under warranty.

5. Disconnect the Lamp End Connector from the old Lamp.

6. Plug the new Lamp flush into the Lamp End Connector. If the Lamp is not plugged in all the way

it may cause damage to the unit and is not covered under warranty.

7. Insert the Lamp straight into the Quartz Sleeve. Be careful, inserting the Lamp at an angle, even

a slight angle, can cause a "U" shaped crack in the Quartz Sleeve.

8. Twist on the Transformer Cap. Do not over tighten. This is a connection only and is not in

contact with water.

9. Tighten the Davis or Hubl Connector located behind the Transformer Cap.

10. FINAL LEAK CHECK: Do not plug the Sterilizer into power yet, turn on the pump, let water run

for 5 minutes and check for leaks.

11. Once a leak test is completed and there are no leaks, plug the Transformer into a GFCI outlet.

Warranty is void if not plugged into a GFCI.

19 AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO, TEMECULA, CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

CLEANING THE QUARTZ SLEEVE

1.

Unplug the UV from the power source and turn off the pump.

2.

Unscrew the Davis or Hubl Connector located

behind the Transformer Cap, this allows your

Transformer Cap to spin freely.

Unscrew Davis Connector

Transformer Cap

Unscrew Transformer Cap

3.

Twist off the Transformer Cap.

4. Slide Lamp out, be careful not to slide the Lamp out at an angle, even a slight angle, this may

cause a “U” shaped crack at the end of the Quartz Sleeve, or possible breakage of the Lamp.

Set the lamp on a secure level surface to avoid breakage.

For Units Without Wipers (for Wiper units, see page 21)

5. Remove the E-Z Twist Top. The Quartz Sleeve Assembly will come out with it. Be careful to

pull it out straight.

NOTE: The Lamps and Quartz Sleeves should be handled with care. Lamps and Quartz

Sleeves are not warranted against breakage and damage.

6. The Quartz Sleeve can be cleaned with Lime Away, CLR or similar products.

Do not use any type of abrasive substance on the Quartz Sleeve as it may scratch the Quartz.

7. To reinstall the Quartz Sleeve, carefully insert the Quartz Sleeve into the end of the UV body.

Be sure the Quartz Sleeve is seated in the bottom of the UV Unit.

Quartz Sleeve

8. Screw on the E-Z Twist Top. Do not use a pipe wrench, pliers or any other tool on this unit.

Tighten by hand only. Re-install the Lamp as Shown on page 19, starting at #6.

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

20

CLEANING THE QUARTZ SLEEVE FOR WIPER UNITS

1.

Unplug the UV from the power source and turn off the pump.

Unscrew Davis Connector

2.

Unscrew the Davis or Hubl Connector

located behind the Transformer Cap,

this allows your Transformer Cap to

spin freely.

Transformer Cap

Unscrew Transformer Cap

3.

Twist off the Transformer Cap.

4. Slide Lamp out, be careful not to slide the Lamp out at an angle, even a slight angle, this may

cause a “U” shaped crack at the end of the Quartz Sleeve, or possible breakage of the Lamp.

Set the lamp on a secure level surface to avoid breakage.

EZ Twist Top

Wiper Extended Out

5. Pull the Wiper Rod completely out (fully extended)

6. Twist off the large nut (E-Z Twist Top). This will release the Quartz Sleeve and the assembly

will still be intact.

7. The Quartz Sleeve can be cleaned with Lime Away, CLR or similar products.

Note: Do not use any type of abrasive substance on the Quartz Sleeve as it may scratch the

quartz.

8. Once the sleeve has been cleaned, wet the Wiper Blades and the outside of the Quartz Sleeve.

Note: Use water only do not use any lubricant.

9. Push the rod completely into the unit and insert Quartz Sleeve assembly through the blade(s).

Please note units that use 40 Watt Lamps have 2 Wiper Blades, be sure to insert Quartz

Sleeve into both Blades. Be sure the Quartz Sleeve is seated in the bottom of the UV Body.

Rod all the way in

10. Screw on the EZ Twist top. Do not use a pipe wrench, pliers or any other tool on this unit.

Tighten by hand only. Re-Install the lamp as shown on page 19, starting at #6.

21

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

Rod all the way in

REPLACEMENT OF THE QUARTZ

1. Unplug system, turn pump off and drain housing. Remove Lamp and Transformer.

TM

Wiper Extended Out

Note: If you have the Wiper option, pull the Wiper Rod out to be fully extended.

EZ Twist Top

Quartz Sleeve

Quartz Cap

Quartz Sleeve Assembly

2. Untwist E-Z Twist Top. This will release the Quartz Sleeve Assembly. Pull The Quartz Sleeve

Assembly straight out of the housing.

3. Untwist Quartz Cap. Push Quartz Sleeve up through E-Z Twist Top. Be careful not to break the

Quartz Sleeve. Handling broken glass can cause injury. If your Quartz Sleeve is broken protect

your hands before servicing.

4. Discard old Quartz Sleeve and Rubber Seal.

5. Re-install E-Z Twist Top without Quartz Sleeve. Slide Quartz Sleeve into the housing. Be sure to

center the quartz sleeve into the seat at the bottom of the unit. Note if you have a the Wiper

Option: Push the rod completely into the unit and insert Quartz Sleeve assembly through the

blade(s). Please note units that use 40 Watt Lamps have 2 Wiper Blades, be sure to insert Quartz

Sleeve into both Blades. Be sure the Quartz Sleeve is seated in the bottom of the UV Body.

6. Gently push the Quartz Sleeve and Rubber Seal in to the E-Z Twist Top until only ½ the rubber

seal is visible.

Ti gh ten Cap

Quartz Cap

7. Twist on the Quartz Cap. DO NOT use a pipe wrench, pliers or any other tool on this unit. Tighten

by hand only.

To Reinstall the Lamp

Go to step #6 under changing the Lamp on page 19.

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

22

WIPER MAINTENANCE

NOTE: The Wiper Rod should be pulled at least once a week for optimum performance. The pump does not need to be turned off. Do not pull the Wiper Rod on a dry unit. Always wet the Quartz Sleeve first.

REPLACING THE WIPER BLADES AND WIPER NUT

It is recommended that the wiper blades and Wiper Nut be replaced every time you change your lamp. Also, when reinstalling the sterilizer after winter.

1. Unplug the unit and turn off the pump.

2. Unscrew the Davis or Hubl Connector located behind the Transformer Cap.

3. Twist off the Transformer Cap.

4. Slide the Lamp out while still connected to the Transformer. Be careful not to slide the Lamp out at an angle, even a slight angle, this may cause a “U” shaped crack at the end of the Quartz Sleeve or possibly break the

Lamp. Do not force the Lamp out of the Quartz Sleeve, any force would be an indication of an improper removal of the Lamp!!

5. Drain the housing.

6. Pull the Wiper Rod completely out (fully extended).

EZ Twist Top

Wiper Extended Out

7. Twist off the large cap

EZ Twist Top

(EZ twist top) this will

Wiper Extended Out

8. Remove the Quartz Sleeve Assembly.

EZ Twist Top

Quartz Cap

9. Unscrew the wiper ball and remove the hex nut.

Wiper Rod

Hex Nut Wiper Ball

Quartz Sleeve

10. Using a 1/2” wrench, unscrew and remove the wiper nut located at the base of the unit. Be very careful

not to cross thread.

Wiper Nut

23

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

11. Pull the Wiper Rod from the large open end of the unit.

WIPER MAINTENANCE

12. Using needle nose pliers, remove the top C-Clip from Wiper Rod. This will release the Wiper Blade.

13. Remove and replace Wiper Blade.

14. Using needle nose pliers replace the top C-Clip into the top notch on the rod. Make sure the blade is

secure.

Do not use the old c-clip or it will fall off.

15. Insert rod assembly back in through the large open end of the unit (from which it was

removed) and guide rod out through hole at the base of the unit.

16. Screw new Wiper Nut in over the threads at the end of the rod and slide it the rest of the way down, until

the nut is resting on the base of the unit. NOTE: Make sure to SCREW the nut over the threads on the

rod or the seal inside of the wiper unit can be compromised causing the unit to leak. Do not use any

lubricants.

17. Using a 1⁄2” wrench screw the nut into the base of the unit. Be careful not to cross thread.

18. Re-install Hex Nut and Wiper Ball on the end of the rod.

19. Wet Wiper Blade and the outside of the Quartz Sleeve.

20. Push rod completely into the unit and insert Quartz Sleeve assembly through the blade. PLEASE NOTE:

40 Watt units have 2 wiper blades, be sure to insert in both blades. Make sure the Quartz Sleeve is

inserted in the seat at the bottom of the unit. Hand tighten EZ twist cap.

Rod all the way in

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

24

PARTS LIST

Optional Mounting

Bracket with Grip

Optional

Winterizing Cap

Wiper Rod

C-Clip Wiper Blade C-Clip Wiper Nut Hex Nut Wiper Ball

Wiper Assembly

SCH 40 2" Pipe

Supplied by Customer

UV LAMPS

25

8 Watt

15 Watt

25 Watt

40 Watt

57 Watt

UV QUARTZ SLEEVES

8 Watt

15 Watt

25 Watt

40 Watt

57 Watt

15“

15“

19“

36“

19“

11-5/8”

11-5/8“

17-1/2“

33-1/2”

17-1/2“

PART NUMBER

A20008

A20015

A20025

A20040

A20057

PART NUMBER

A10008

A10015

A10025

A10040

A10057

PART #

A40054

A40124

A40014

A40011

A40004

A40068

A40012

A40007

A40116

PART # Description

A40073 Wiper Ball

A40090 Wiper Hex Nut

A40021 Wiper Nut

A40019 8/15 Watt Wiper Rod (RMA)

A40010 25/57 Watt Wiper Rod (RMA)

A40013 40 Watt Wiper Rod (RMA)

A40017 Wiper Blade With Plastic Clips

A40172 Wiper Blade With Metal Clips

A40089 Metal C-Clip for Wiper Blade

A40180 Plastic C-Clip for Wiper Blade

A40032 2” Union, White

Description

Barb Fitting 3/4”

Mounting Clip Grip Hold

O-Ring for EZ Twist Top

Quartz Cap, Clear

Rubber Seal, Purple

EZ Twist Top, Black w/ O-Ring

EZ Twist Top, White, w/ O-Ring

Winterize Cap

2” Union, Black

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

PARTS LIST TRANSFORMERS

THE CLASSIC SERIES INLINE TRANSFORMERS

Transformer

Transformer Cap

Davis Connector

Cord Length aprox. 17-1/2”

TM

Lamp End

Connector

Cords not sold separately

THE CLASSIC SERIES NEMA TRANSFORMERS

PARTS LIST

PART #

A30045

A30056

A30080

A30114

A30120

A30160

A30200

A30240

A30042

A30058

A30082

A30115

Description

40W NEMA Transformer

57W NEMA Transformer

80W NEMA Transformer

114W NEMA Transformer

120W NEMA Transformer

160W NEMA Transformer

200W NEMA Transformer

240W NEMA Transformer

RAW 40 Watt Transformer

RAW 57 Watt Transformer

RAW 80 Watt Transformer

RAW 114 Watt Transformer

PART #

A40002

A40109

A40113

A30007

A30014

A30024

A30044

A30055

PART #

A40088

A40002

A40113

A40062

A40063

A40065

A40106

A40066

A40092

A40093

A40094

Description

Lamp End Connector

Davis Connector

Transformer Cap, Black

8W Transformer

15W Transformer

25W Transformer

40W Transformer

57W Transformer

Description

Hubl Connector

Lamp End Connector

Transformer Cap Black

Wiring Harness 40 Watt

Wiring Harness 57 Watt

Wiring Harness 80 Watt

Wiring Harness 114 Watt

Wiring Harness 120 Watt

Wiring Harness 160 Watt

Wiring Harness 200 Watt

Wiring Harness 240 Watt

* NEMA transformers are the entire Transformer component. Complete transformers come with a NEMA box,

RAW transformer, wiring harness, hubl connector, transformer cap, lamp end connector, and power cord.

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

26

INCORRECT INSTALLATIONS

The Following will Damage the Unit’s Electrical Components

Incorrect: EZ Twist Top Over Rubber Seal

See Page 22 for Proper Quartz Sleeve installation

Incorrect: Quartz Sleeve is Outside of Wiper Blade

See Page 21 for Proper Quartz Sleeve installation

Wiper Blade

Rubber Seal

EZ Twist Top

Incorrect: Rubber Seal is Outside of Quartz Cap

See Page 22 for Proper Quartz Sleeve installation

Rubber Seal

Incorrect: 40 Watt and Multi-Units with Wipers.

One Blade over the Quartz Sleeve and One Blade

Outside of the Quartz Sleeve

See Page 21 for Proper Quartz Sleeve installation

Wiper Blade

Quartz Cap

Incorrect: Quartz Sleeve Not Seated

See Page 22 for Proper Quartz Sleeve installation

Quartz Sleeve

Lamp Dropped in Quartz Sleeve can Cause Breakage

Incorrect: Lamp at an Angle will create a U Shaped Crack

See Page 15 for Proper Lamp installation

Incorrect: Lamp Not Plugged Flush with Lamp End Connector

See Page 15 for Proper Lamp installation

27

AQUA ULTRAVIOLET 42371 AVENIDA ALVARADO TEMECULA CA 92590 TEL: 951-296-3480 FAX: 951-296-3490

A11046 051909

42371 Avenida Alvarado

Temecula, CA 92590

TOLL FREE: (800) 454-2725

TEL: (951) 296-3480

FAX: (951) 296-3490 www.aquauv.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement