Pocket PC Phone
2
Pocket PC Phone User Manual
Please Read Before Proceeding
THIS DEVICE IS NOT CHARGED WHEN YOU TAKE IT OUT OF THE BOX.
DO NOT REMOVE THE BATTERY PACK WHEN THE DEVICE IS CHARGING.
WHEN INSERTING YOUR SIM CARD, MAKE SURE THE DEVICE IS POWERED OFF, AND
THAT THE SIM CARD SNAPS INTO THE SOCKET.
YOUR WARRANTY IS INVALIDATED IF YOU OPEN OR TAMPER WITH THE DEVICE’S OUTER
CASING.
EXPLOSIVE ATMOSPHERES
When in any area with a potentially explosive atmosphere or where flammable materials exist, the product
should be turned off and the user should obey all signs and instructions. Sparks in such areas could cause an
explosion or fire resulting in bodily injury or even death. Users are advised not to use the equipment at refueling
points such as service or gas stations. Users are reminded of the need to observe restrictions on the use of radio
equipment in fuel depots, chemical plants or where blasting operations are in progress. Areas with a potentially
explosive atmosphere are often, but not always, clearly marked. These include fuelling areas, below deck on
boats, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles,
such as grain, dust, or metal powders.
PRIVACY RESTRICTIONS
Some countries require full disclosure of recorded telephone conversations, and stipulate that you must inform
the person with whom you are speaking that the conversation is being recorded. Always obey the relevant laws
and regulations of your country when using the recording feature of your Pocket PC Phone.
Pocket PC Phone User Manual
3
Important Safety Precautions
When using this product, the safety precautions below must be taken to offset possible legal
liabilities and damages.
n ELECTRICAL SAFETY
This product is intended for use when supplied with power from the battery. Other usage may be
dangerous and will invalidate any approval given to this product.
n SAFETY IN AIRCRAFTS
Due to the possible interference caused by this product to an aircraft's navigation system and
its communications network, using this product on board an airplane is against the law in most
countries.
n ENVIRONMENT RESTRICTIONS
Do no use this product at gas or refueling stations. The use of this product is also prohibited in fuel
storehouse, chemical plants, and locations containing explosives.
n ROAD SAFETY
Vehicle drivers in motion are not permitted to use telephony services with handheld devices,
except in the case of emergency. In some countries, using hand-free devices as an alternative
is allowed.
n INTERFERENCE WITH MEDICAL EQUIPMENT FUNCTIONS
This product may cause medical equipment to malfunction. The use of this device is forbidden in
most hospitals and medical clinics.
n
NONIONIZING RADIATION
This product should be operated in the suggested normal condition only to ensure the radiative
performance and safety of the interference. As with other mobile radio transmitting equipment,
users are advised that for satisfactory operation of the equipment and for the safety of personnel,
it is recommended that no part of the human body be allowed to come too close to the antenna
during operation of the equipment.
4
Pocket PC Phone User Manual
Contents
Chapter 1
1.1
1.2
1.3
1.4
Knowing Your Device ............... 10
Inserting the SIM Card ............ 12
Battery ...................................... 13
Accessories .............................. 15
Chapter 2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
Getting Started
Knowing Your Pocket PC Phone
Starting Up ............................... 18
Entering Information ................. 25
Phone Pad................................ 30
Writing on the Screen................33
Drawing on the Screen............. 35
Recording a Message .............. 36
Finding Information................... 38
Chapter 3
Using Your Pocket PC Phone
3.1 About Your Pocket PC Phone.. 42
3.2 Making a Call............................ 46
Pocket PC Phone User Manual
3.3
3.4
3.5
3.6
3.7
3.8
3.9
Smart Dialing............................ 49
Receiving a call ........................ 52
In-Call Options.......................... 53
Contacts Information ................ 55
Photo Contacts......................... 57
Additional Dialing Information... 64
Securing Your Pocket PC
Phone ...................................... 65
Chapter 4
Synchronizing Information
4.1 Using ActiveSync...................... 68
4.2 Synchronizing Information........ 70
4.3 Infrared and Bluetooth
Connection............................... 73
4.4 ActiveSync Errors..................... 74
Chapter 5
Personalizing Your Pocket
PC Phone
5.1 Device Settings ........................ 76
5.2 Phone Settings ......................... 84
5
6
Pocket PC Phone User Manual
Chapter 6
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
About Connections ................... 88
Connecting to the Internet ........ 88
CSD Line Type ......................... 90
Pocket Internet Explorer .......... 91
Network Cards Settings............ 92
Terminal Services Client........... 93
Bluetooth .................................. 94
Wireless Modem..................... 100
Chapter 7
7.1
7.2
7.3
7.4
Getting Connected
Using Outlook
Calendar................................. 106
Contacts ................................. 108
Tasks .......................................111
Notes ...................................... 112
Chapter 8
Messaging Features
8.1 E-Mail and Text Messages..... 116
8.2 MSN Messenger..................... 121
8.3 MMS Messages...................... 123
Pocket PC Phone User Manual
Chapter 9
9.1
9.2
9.3
9.4
9.5
9.6
9.7
Applications
Pocket Word........................... 132
Pocket Excel........................... 133
Windows Media Player........... 134
Pictures .................................. 135
ClearVue PPT......................... 139
ClearVue PDF ........................ 142
MIDlet Manager...................... 143
Chapter 10 Using Camera and Album
10.1 About Camera and Album ..... 152
10.2 Camera ................................. 153
10.3 Album ................................... 165
Appendix A
Adding or Removing Programs...... 176
Managing Memory..........................178
Backing Up Files ............................ 180
Resetting Your Pocket PC Phone . 181
7
8
Pocket PC Phone User Manual
Appendix B
Regulatory Agency IDs.............................184
European Union Notice............................184
Important Health and Safety Information..186
Troubleshooting........................................189
Specifications
195
Index
196
Chapter 1
Getting Started
1.1 Knowing Your Device
1.2 Inserting the SIM Card
1.3 Battery
1.4 Accessories
10
Pocket PC Phone User Manual
1.1 Knowing Your Device
Top View, Left-Side View, and Front View
MMC/SD or SDIO slot
Insert MMC card or a SDIO
Accessory here.
Notification
LEDs
Camera
GSM standby, message,
GSM network status, PDA
notification, Bluetooth, power
notification and battery
charge status.
Press to launch Camera.
Press again to take a
picture.
Volume
Touch Screen
Press UP/DOWN to adjust
the volume.
End
Record/VoiceDial
Press to end a call.
Long press to record a
voice note.
Press lightly to launch
VoiceDial.
Calendar
Press for quick access to your
calendar.
Talk/Send
Press to answer an
incoming call or dial a
number.
Navigation Pad
Contacts
Press for quick access
to your contacts.
Press to move up/down
and left/right through any
of the drop-down menus
or program instructions;
select by pressing the Action
key on the center of the pad.
Pocket PC Phone User Manual
11
Right-Side View, Back View, and Bottom View
Car Antenna Connector
You can connect your phone to a car
antenna to utilize the superior reception
quality.
Stylus and Stylus Slot
Self-portrait
mirror
Power Button/
Backlight
Camera Lens
Press to turn ON/OFF your
device or backlight.
Earphone Plug
Infrared Port
Allows you to listen
to audio media
or use the phone
hands-free kit.
Enables to exchange file(s)
or data with other devices
without cables or wires.
Soft Reset
Microphone
Press here with stylus
to reset your device.
Mini USB Connector
Use this connector to
synchronise, transmit data or
recharge the battery.
Speak here when
receiving/making a
phone call or voice
recording.
12
Pocket PC Phone User Manual
1.2 Inserting the SIM Card
1. Ensure the device is turned off.
2. Turn your device over and press the back cover lightly to slide out the back cover.
3. Switch the red battery lock to release the battery pack. Then, use your finger to lift up
the battery from the left side of the battery slot.
locked
unlocked
4. Insert the SIM card with its gold contacts face down. Its cut off corner should match the
cut off corner in the slot. If you wish to take the SIM card out, use the stylus to press into
the SIM card slot hole, and then lightly lift up the SIM card while pressing the left-most
side of the SIM card, and then slide it out.
Slide the SIM
card into the
SIM card slot.
Press lightly to
slide the SIM
card out.
Use the stylus to
press into the SIM
card slot hole.
Pocket PC Phone User Manual
13
5. Replace the battery by inserting the right side first. Then, push back the red battery lock
into place to fix the battery.
6. To replace the back cover, lay it on the back of the device, lining up the grips on the upper
side of the back cover with the slots on the side of the device. Finally, slide forward to
snap into place.
1.3 Battery
Your Pocket PC Phone contains a rechargeable Li-ion polymer battery. Battery life depends
on whether you are talking on the phone, using the PDA, or if the device is on standby.
Battery life estimates:
n Talk-time: 4 - 5 hrs.
n PDA: 11 hrs (approximate.).
n Standby: 180 hrs (approximate.).
n Data retention time: 72 hrs.
The above are based on using one function at a time. Battery life
may vary with switching between functions.
WARNING: To reduce the risk of fire or burns, do not disassemble, crush, puncture, short
external contacts, heat above 60℃ (140℉), or dispose of in fire or water. Replace only
with manufacturer specified batteries. Recycle or dispose of used batteries as stipulated
by local regulations.
Data retention
It is vital to keep your battery charged. This is because your Pocket PC Phone does not
have a hard drive, all data and any new programs you install are stored in the RAM. If the
battery completely drains, any data or new programs you installed will be erased. Only the
default programs that came with the device at the time of purchase will remain.
14
Pocket PC Phone User Manual
To prevent this kind of data loss, a portion of the main
battery will keep your data safe for 72 hours if your
device runs out of power. An additional battery, the
internal backup battery, is designed to keep your data
safe when you remove the main battery. It will keep the
data safe for 30 minutes.
NOTE: Be sure to check that the internal backup battery
power remains at least at 50% OR ABOVE before you
remove the main battery by tapping the Start menu >
Settings > the System tab > Power.
Recharging your device
You can recharge your device in the following ways:
1.
Connect your Pocket PC Phone directly to the AC adapter that is provided.
Plug the AC adapter
into an electrical outlet
2.
You can also charge your Pocket PC Phone by plugging the Sync cable into
your PC's USB port.
Pocket PC Phone User Manual
15
When the battery is low
When the low-battery warning message appears, immediately save any data you are
working on, perform synchronization with your PC, and turn off your Pocket PC Phone. The
internal backup battery can only protect the data in case of battery or SIM card change.
Data retention in the case of shut down (low battery) is 72 hours.
1.4 Accessories
AC Adapter
The AC adapter allow you to recharge your Pocket PC Phone.
USB Cable
The optional USB cable allows you to synchronize with a PC .
Headset
The stereo handset has a volume control and a button where press once to pick up a
phone call and hold 2 seconds to end a phone call. During a phone call, press once to
switch between calls.
16
Pocket PC Phone User Manual
Chapter 2
Knowing Your Pocket PC
2.1 Starting Up
2.2 Entering Information
2.3 Phone Pad
2.3 Writing on the Screen
2.4 Drawing on the Screen
2.5 Recording a Message
2.6 Finding Information
18
Pocket PC Phone User Manual
2.1 Starting Up
Turning Your Pocket PC Phone On and Off
To turn your device on:
Press the Power Button on the right side of the device. (The Pocket PC Phone will power
up and, if this is the first time it has powered up, will automatically begin the initiation/
calibration process. See below for further details.)
To turn your device off:
Press the Power Button on the right side of the device.
Note: Turning your device off doesn’t turn the phone off. To turn the phone off, press and
hold for two seconds.
Screen tapping and calibration
When you first start up your Pocket PC, you will be asked to calibrate the screen by tapping
the center of a cross with your stylus as it moves around the screen. This process ensures
that when you tap the screen with your stylus, the tapped item is activated.
Re-calibrate the screen
If your Pocket PC Phone does not accurately respond to screen taps, you will need to
re-calibrate it:
1. Tap the Start menu > Settings > the System tab > Screen.
2. Tap the Align Screen button on the General tab to re-calibrate the screen as described
above.
Note: When aligning the touch screen, tap the target firmly and accurately.
Pocket PC Phone User Manual
19
Screen Orientation
Portrait Mode
Landscape Mode
Tap on this icon to change screen orientation.
To switch the orientation of your touch screen between the Portrait mode or the Landscape
mode, select the Orientation options by tapping the lower right Screen Orientation icon
, tap once for Landscape (right-handed), another one for Landscape(left-handed). Or,
alternatively, you can tap the Start menu > Settings > the System tab > Screen. The
Portrait mode allows you to get a better view or a better operation of certain programs on
your Pocket PC, while Landscape may be optimal for viewing longer text files.
For easier reading of text in programs that support ClearType, tap the ClearType tab, and
then select Enable ClearType. To increase readability or see more content by adjusting
the size of text in programs that support it, tap the Text Size tab. Move the slider to make
text larger or smaller.
20
Pocket PC Phone User Manual
The Today screen
1
23 4 5
6
7
10
8
1. Tap to bring up a menu list of programs.
9
2. Tap to view call status information.
3. Tap to view network status and options.
4. Tap to change volume or mute all sounds.
5. Tap and hold to change time format.
6. Tap to change date and time.
7. Your day-at-a-glance reminders. Tap to open the related program.
8. Tap to create a new item.
9. Tap to disconnect ActiveSync, or turn ON/OFF Bluetooth.
10. Tap to change screen orientation.
Note: To go back to the Today screen when you are using other programs, just tap the
Start menu > Today.
Note: To customize the Today screen display, including the background image, tap the
Start menu > Settings > the Personal tab > Today. Please refer to Chapter 5 for more
information.
Pocket PC Phone User Manual
21
Indicators
Your Pocket PC's status indicators are located at the top right of the Today screen. Some
common indicators are listed below. If you are not sure about the meaning of an indicator,
tap on it with your stylus and a dialog box will explain its function and allow you to change
the settings for that particular icon.
Indicators
Meaning
/
Sounds are off / sounds are on.
/
Main battery with full strength/ No battery
/
Main battery low/ very low.
Backup battery is very low.
Indicates that Caller ID monitor program is not yet ready to receive
calls.
Data connection is active.
Indicates that your Pocket PC Phone is roaming in a different
network area.
Notification that one or more instant messages were received.
Notification that one or more mobile e-mail/text messages were
received.
/
Indicates the connection to your service provider/network operator is
on/off. (with signal strength)
Indicates that your Pocket PC Phone is synchronized with a PC.
Indicates that more notification icons need to be displayed. Tap the
icon to view all.
22
Pocket PC Phone User Manual
Notifications
Your Pocket PC Phone reminds you in a variety of ways when you have something to do or
when you have received an SMS message. For example, if you’ve set up an appointment
in Calendar, a task with a due date in Tasks, or an alarm in Clock, you will be notified in
any of the following ways:
n A message box appears on the screen.
n A sound, which you can specify, is played.
n A light flashes on your Pocket PC.
n The Pocket PC Phone vibrates.
To choose reminder types and sounds for your device, the Start menu > Settings > the
Personal tab > Sounds & Notifications. The options you choose here apply throughout
the Pocket PC.
Pop-Up menus
Use pop-up menus to quickly perform an action on an item. To access a pop-up menu,
tap and hold the item that you want to perform the action on. When the menu appears,
tap the action you want to perform, or tap anywhere outside the menu to close it without
performing an action.
1. Tap and hold to display the pop-up menu.
2. Lift the stylus and tap the action you want.
3. Tap outside the menu to close it without performing an action.
Pocket PC Phone User Manual
23
Navigation bar
The navigation bar, located at the top of the screen, displays active programs and current
time, and enables you to switch between programs and close screens.
1. Tap to switch to a program.
2. Tap to switch to a recently used program.
1
5
4
3. Tap to see more programs.
2
4. Tap to change device settings.
3
5. Tap to see a Help topic for the current screen.
Command bar
Use the command bar at the bottom of the screen to perform tasks in programs. The
command bar includes menu names, buttons, and the Input Panel button.
1
2
3
4
1. To create a new item in the current program, tap New.
2. Tap to select menu commands.
3. Tap to select button commands.
4. Tap to display the input panel.
To see the name of a button, tap and hold the stylus on the button. Drag the stylus off the
button so that the command is not carried out.
24
Pocket PC Phone User Manual
Programs
You can switch from one program to another by selecting it from the Start menu.
To access a program, tap the Start menu > Programs, and then the program name. You
can also switch to some programs by pressing a program button on your device. For more
information about the Button settings, please see Chapter 5.
Icon
Description
ActiveSync synchronizes information between your device and PC.
xBackup backs up your Pocket PC Phone files.
Contacts keeps track of your friends and colleagues.
Messaging sends and receives Email/SMS/MMS messages.
Pocket IE browses Web sites and downloads new programs and files.
SIM Tool Kit (STK) allows you to access information and other services offered by
your operator.
Phone makes/receives calls, and switches between calls.
Calculator performs basic arithmetic.
Wireless Modem uses your Pocket PC Phone as an external modem for a PC.
SIM Manager collects, organizes, and sorts the Contacts list stored on your SIM
card.
Calendar keeps track of your appointments and creates meeting requests.
Tasks keeps track of your tasks and reminds you of important events.
Pocket PC Phone User Manual
Icon
25
Description
Windows Media plays sound or video files.
Pocket Excel creates, views, and edits Excel workbooks.
Pocket Word creates, views, and edits MS-Word documents.
MSN Messenger sends and receives instant messages.
Pictures collects, organizes, and sorts .jpg picture files.
Games such as Jawbreaker and Solitaire are included.
File Explorer views all the files on your Pocket PC.
Camera snaps photos or shoots video clips.
Album collects, organizes, and sorts .JPG/.BMP/.GIF files.
Photo Contacts inputs the image files according to your Contacts list and sets up
Caller ID.
Notes creates handwritten or typed notes, drawings, and recordings.
2.2 Entering Information
You can enter information on your device in the following ways:
n Synchronizing: Using ActiveSync, exchange information between your PC and device.
(For more information on ActiveSync, see Chapter 4).
n Typing: Using the Input Panel or the keyboard on the bottom of your device, enter typed
text into the device. You can do this by tapping keys on the screen soft keyboard, by pressing
the keyboard, or by using the handwriting recognition software.
26
Pocket PC Phone User Manual
n Writing: Using the stylus, write directly on the screen.
n Drawing: Using the stylus, draw directly on the screen.
n Recording: Create a stand-alone recording or embed a recording into a document or
note.
Using the Input Panel
Tap to change
input panel options
Tap to select an
input panel
Tap to open the selected
input panel
Tap to see the list
of input panels
Use the input panel to enter information in any program on your device. You can either
type using the soft Keyboard or write using Letter Recognizer, Block Recognizer, Transcriber, or Phone Pad. In any case, the characters appear as typed text on the screen.
Using the Soft Keyboard
To show or hide the input panel, tap the Input Panel button
. To see your choices, tap
the arrow next to the Input Panel button. Tap the arrow next to the Input Panel button
, and then Keyboard.
1. To type lowercase letters, tap the keys with the stylus. To type a single uppercase
letter or symbol, tap the Shift key. To tap multiple uppercase letters or symbols, tap the
CAP key. You can also tap and hold the stylus on the key and drag up to type a single
uppercase letter.
Pocket PC Phone User Manual
27
Tap to add the word if this
is the right one for you
2. To add a space, in addition to tapping the space bar, you can also tap and hold any key
and then drag the stylus to the right. To backspace one character, in stead of tapping
the backspace key, you can also tap and hold any key and then drag the stylus to the
left across at least two other characters.
3. To insert a carriage return, tap and hold the stylus anywhere on the keyboard and drag
down. When you use the input panel, your device anticipates the word you are typing
or writing and displays it above the input panel. When you tap the displayed word, it is
automatically inserted into your text at the insertion point. The more you use your device,
the more words it learns to anticipate.
Note: To change word suggestion options, such as the number of words suggested at one
time, tap the Start menu > Settings > the Personal tab > Input > the Word Completion
tab. For more information about Input settings, please see Chapter 5.
Using the Letter Recognizer
With the Letter Recognizer, you can write letters using the stylus just as you would on
paper.
1. Tap the arrow next to the Input Panel button
2. Write a letter in the box.
, and then Letter Recognizer.
28
Pocket PC Phone User Manual
When you write a letter, it is converted to typed text that appears on the screen. For specific
instructions on using Letter Recognizer, with Letter Recognizer open, tap the question
mark
next to the writing area.
Using the Block Recognizer
With the Block Recognizer, you can input character strokes using the stylus that are
similar to those used on other devices.
1. Tap the arrow next to the Input Panel button
, and then Block Recognizer.
2. Write a letter in the box.
When you write a letter, it is converted to typed text that appears on the screen. For
specific instructions on using Block Recognizer, tap the question mark
next to the
writing area.
Switching to Transcriber
With Transcriber, you can write anywhere on the screen using the stylus just as you would
write on paper. Unlike Letter Recognizer and Block Recognizer, you can write a sentence
or more. Pause and let Transcriber change the written characters to typed characters.
1. Tap the arrow next to the Input Panel button, and then Transcriber.
2. Write anywhere on the screen.
For specific instructions on using Transcriber, open Transcriber open, and tap the question
mark in the lower right-hand corner of the screen.
To punctuate in Transcriber:
1. Tap the keyboard button
on the tool bar.
2. Tap the desired punctuation.
3. Tap the keyboard button
again to hide the keyboard.
Pocket PC Phone User Manual
29
To learn writing in Transcriber:
1. Tap
on the tool bar.
2. A Letter Shapes Selector screen will appear:
n At the bottom of the screen, select the character you wish to explore.
n At the top of the screen, tap the picture of this character. It will slowly redraw, showing the
writing sequence.
n Select how often you write the character using that method.
When you finish the selecting all the letters, you can save these as a profile by tapping
File > Save, and enter a name for the profile.
Using Profiles
Letter Shape Selector supports two profiles: Master or Guest:
n Master is typically used by the Pocket PC's primary user. This profile is unaffected by any
Guest user settings.
n Guest is for temporary device usage by another person.
Editing and selecting text
Each input program provides cursor keys to move through text and backspace so that you
can correct spelling, grammar or insert additional information. Alternatively, you can use
your stylus to make an insertion.
To select typed text, drag the stylus across the text you want to select. You can cut, copy,
and paste text by tapping and holding the selected words, and then tapping an editing
command on the pop-up menu, or by tapping the command on the Edit menu.
30
Pocket PC Phone User Manual
2.3 Phone Pad
Phone Pad is a Soft Input Panel (SIP) application that provides a flexible alternate input
method. With it, you can easily switch among three input modes (T9, Multi-Tap, and
Numeric) plus a Symbols menu, with greater convenience.
Using Phone Pad
Phone Pad can be activated at any time, except when in the Today screen or when in
Camera mode. To use Phone Pad, tap-and-hold the Keyboard icon which is shown near
the lower right corner of your screen, next to the triangular-shaped menu icon. Then
select Phone Pad from the menu to open the Phone Pad input panel.
Using T9 to Input Text
By default, Phone Pad is in T9 mode. It is the easiest and most convenient way to input
text in English. As you press alphanumeric buttons on the Phone Pad input panel, T9
tries to automatically match the letters you have selected with the most likely completed
word.
To type a word: Simply tap on the numeric keypad.
Pocket PC Phone User Manual
31
To insert a word in the current application screen:
1. Tap any word in the wordlist.
2. Tap the space key.
3. Select a word and tap enter to insert the word.
To enter a number:
1. Tap and hold the number key on the Input panel.
2. Or, tap the button to switch to numeric mode.
Then tap the desired number(s).
To insert a tab: Tap and hold the space key.
To scroll the wordlist: Tap the left / right arrow keys.
To enter a capital: Tap the Shift key.
To add symbols:
1. Tap the 1 key to display the most frequently used
symbols on the screen.
2. Or, tap the sym key to see all the symbols. Then,
tap on the desired one(s) to enter to the wordlist
or application screen.
Using the Multi-Tap mode to Input Text
Unlike the T9 input mode, the Multi-Tap input mode will not search for all the possible
combinations of letters or try to guess at a partial word’s completion. You need to manually
enter all letters yourself to form words.
For example:
If you want to enter two consecutive “d” letters, tap the 3def key once, wait one second,
then tap again to enter the second “d.” Or, if you want to enter “e” into the Wordlist, you
32
Pocket PC Phone User Manual
must tap the 3def key twice quickly so that the “e” will be recognized, or tap three times
quickly if you wish to enter the letter “f.”
Entering Numbers
When 123 is indicated as the input mode, each time you press a number button on the
input panel, the associated number will display in the Wordlist panel.
After you have entered the desired number(s), tap the Enter button to insert the number(s)
on the screen. Or, if you wish to add a space after the number(s) is displayed, tap the
Space button instead.
Phone Pad Options
This feature lets you select various options for Phone Pad. You can invoke the Phone
Pad options screen in the following ways:
n Tap and hold the opt/sym button in Phone Pad.
n Tap the triangular icon in the extreme lower right corner of the screen. A menu
containing the Options command opens. Select Options from the menu.
Select Phone Pad as the input method, and then tap the Options button.
n Select Start Menu > Settings > Personal Tab > Input.
Pocket PC Phone User Manual
33
The Phone Pad options available are:
n Turn on one-touch symbol entry
Check this box to select one symbol at a time.
n Auto-hide matching wordlist
Check this box to hide the word list after you
select a word.
n Turn on screen tap sound
Check this box to play a sound each time you tap
a key in Phone Pad.
n Automatically add a space after selecting a
word
Check this box to add a space automatically at
the end of every word, after entering a word.
n Enable pop-up menu for deleting user-defined
words
Check this option to display a pop-up menu
whenever you tap on a word that is in the user
database.
2.4 Writing on the Screen
In any program that accepts writing, such as Notes, and in the Notes tab in Calendar,
Contacts, and Tasks, you can use your stylus to write directly on the screen. Write as you
would on paper. You can edit and format what you have written and convert the information
into typed text at a later time.
Tap the pen button
to switch to writing mode. This action displays lines on the screen
to help you write. Some programs that accept writing may not have the pen button. See
the manual for each particular program to find out how to switch to writing mode.
34
Pocket PC Phone User Manual
Selecting writing
If you want to edit or format writing, select the text first.
1. Tap
again to exit the writing mode. This helps to select the written text more easily.
2. Tap and hold the stylus next to the text you want to select until the insertion point
appears.
3. Without lifting, drag the stylus across the text you want to select.
If you accidentally write on the screen, tap Edit, Undo, and try again.
You can cut, copy, and paste written text in the same way you work with typed text: tap
and hold the selected words, and then tap an editing command on the pop-up menu, or
tap the command on the Edit menu.
Converting writing into text:
1. On the writing note, tap Tools and Recognize from the
menu bar.
2. If you want to convert only certain words, select them
before tapping Recognize on the Tools menu (or tap
and hold the selected words and then tap Recognize on
the pop up menu).
If a word is not recognized, it will be left as writing. And if the
conversion is incorrect, you can select different words from a
list of alternates, or return to the original writing.
Tap and hold the incorrect word (tap one word at a time), then
tap Alternates from the pop-up menu. A menu with a list of
alternate words appears. Tap the word you want to use, or
tap the writing at the top of the menu to return to the original
writing.
The writing is
converted into
typed text
Pocket PC Phone User Manual
35
Tips for good recognition:
1. Write neatly.
2. Write on the lines and draw descanters below the line. Write the cross of the “t” and
apostrophes below the top line so that they are not confused with the word above. Write
periods and commas above the bottom line.
3. For better recognition, use a zoom level of 150% or higher by tapping Tools > Zoom to
change the zoom level.
4. Write the letters of a word closely and leave big gaps between words so that the device
can easily tell where words begin and end.
5. Hyphenated words, foreign words that use special characters such as accents, and some
punctuation cannot be converted.
If you edit or add to a word after attempting to recognize it, the new writing will not be
included if you attempt to recognize it again.
2.5 Drawing on the Screen
You can draw on the screen in the same way that you write on the screen. The difference
between writing and drawing on the screen is how you select items and how they can be
edited. For example, selected drawings can be re-sized, while writing cannot.
To create a drawing:
Cross three ruled lines on your first stroke. A drawing box appears. Subsequent strokes
in, or touching, the drawing box become part of the drawing. Drawings that do not cross
three ruled lines will be treated as writing.
36
Pocket PC Phone User Manual
The drawing box indicates
the boundaries of the
drawing
Pen button
To select a drawing
If you want to edit or format a drawing, you must select it first.
1. Tap and hold the stylus on the drawing until the selection handle appears. To select multiple
drawings, deselect the pen button and then drag to select the drawings you want.
2. You can cut, copy, and paste selected drawings by tapping and holding the selected drawing
and then tapping an editing command on the pop up menu, or by tapping the command on
the Edit menu. To re-size a drawing, make sure the Pen button is not selected, and drag
a selection handle.
To change the zoom level so it is easier to work or view your drawing, tap Tools and then
select a zoom level.
2.6 Recording a Message
In any program where you can write or draw on the screen, you can also quickly capture
thoughts, reminders, and phone numbers by recording a message. In Calendar, Tasks,
and Contacts, you can include a recording in the Notes tab.
Pocket PC Phone User Manual
37
In the Notes program, you can either create a stand-alone recording or include a recording
in a written note. If you want to include the recording in a note, open the note first.
In the Messaging program, you can also add a recording to an E-mail message.
To create a recording:
1. To add a recording to a note, open the note before recording. Tap the Start menu > Programs
> Notes.
2. If there is no Record/Playback toolbar, tap
.
3. Hold your device’s microphone near your mouth or another sound source.
4. To start recording, tap
. A beep will sound.
5. To stop recording, tap
. Two beeps will sound. The new recording appears in the note
list or as an embedded icon.
6. To play a recording, tap in the open note or tap the recording in the note list.
Indicates an embedded
recording
Tap to begin recording Tap to show or hide
the Recording tool bar
38
Pocket PC Phone User Manual
You can also invoke the Record/Playback toolbar by pressing the Record button, which
is the first button from the top on the left side of your Pocket PC.
To quickly create a recording, hold down the Record button. When you hear the beep,
begin your recording. Release the button when you are finished.
The new recording is stored in the open note, or as a stand-alone recording, if no note
is opened.
Pulse Code Modulation (PCM) provides slightly better sound quality. However, PCM
recordings may take up to 50 times more storage space than Mobile Voice recordings.
PCM cannot be used to create recordings that are embedded in notes.
Change recording formats
In the note list, tap Tools > Options > the Global Input Options link (at the bottom of
the page).
Mobile Voice is a 2.4 KB audio codec (compressor/decompressor). It is the recommended
format because it provides good voice recording and takes up far less storage space than
PCM.
2.7 Finding Information
The Find feature on your Pocket PC Phone helps you quickly locate the information you
need.
1. Tap the Start menu > Programs > Find.
2. In Find, enter the file name, word, or other information you want to search for. If you have
looked for this item before, tap the Find arrow and select the item from the list.
3. To help narrow your search, select a data type under Type.
Pocket PC Phone User Manual
39
4. Tap Go. The My Documents folder and sub-folders are searched.
5. In the Results list, tap the item you want to open.
To quickly find information that is taking up storage space on your device, select Larger
than 64 KB in Type.
40
Pocket PC Phone User Manual
Chapter 3
Using Your Pocket PC Phone
3.1 About Your Pocket PC Phone
3.2 Making a Call
3.3 Smart Dialing
3.4 Receiving a Call
3.5 In-Call Options
3.6 Contacts Information
3.7 Photo Contacts
3.8 Additional Dialing Information
3.9 Securing Your Pocket PC Phone
42
Pocket PC Phone User Manual
3.1 About Your Pocket PC Phone
Like a standard mobile phone, you can use your Pocket PC Phone to keep track of calls
and send SMS messages. You can also take notes while talking, dialing directly from Contacts, and easily transfer contacts between your SIM card and the RAM of your device.
The phone dialer screen
To access the Phone Dialer Screen, tap the Start menu > Phone, or press
on your
Pocket PC Phone . From this screen, you can access Call History, Speed Dial, and Phone
Setting. Signal status information and icons that tell you about your call include:
1. Indicates the strength of the signal.
2. The contact name of the number you are
dialing is displayed here.
3. Touchscreen keypad.
1
2
4. Clear, copy, or paste numbers.
5. Tap to access the phone settings.
10
3
6. Tap to make a note during a call.
7. Tap to select your contact from the
Contacts list.
9
8. Tap to end a call.
9. Stores frequently-called numbers.
10. View all history including received, dialed
and missed calls.
8
4
5 6 7
Pocket PC Phone User Manual
43
The navigation pad and dialing
1
3
2
4
7
6
5
1. Phone Dialer Screen: Press to activate the Phone Dialer Screen.
Take a Call: Press to take an incoming call.
Speakerphone: During a call, press and hold to turn the speakerphone ON or OFF.
Dial: Press to dial a phone number.
2. Scroll Up: Press to scroll up through a list, or enter Call history.
3. End Call: Press to end a call or to end a GPRS connection.
4. Call History: After launching the Phone Dialer Screen, press to enter the Call
History feature.
5. Scroll Down: Press to scroll down through a list.
6. Action Key: Press to select a menu item, or to enter Speed Dial.
7. Speed Dial: After launching the Phone Dialer Screen, press to enter the Speed Dial
feature.
44
Pocket PC Phone User Manual
Entering your PIN
Most SIM cards are preset with a PIN (Personal Identification Number). This PIN
is provided by T-Mobile, which you need to enter whenever you use your device. (For
more information on installing your SIM card into your Pocket PC Phone , please see the
illustrations in the Quick Start Guide.)
1. Enter the preset PIN assigned by T-Mobile.
2. Tap the Enter button.
If your PIN is entered incorrectly three times, the SIM card will be blocked. If this happens,
you can unblock it with the PIN Unblocking Key (PUK) from T-Mobile.
Checking your connection
By default, your Pocket PC Phone will automatically connect to the T-Mobile network once
you have inserted a SIM card and entered the required PIN code. The icon
indicates
that you are connected to a T-Mobile network, or an affiliated provider. A full strength signal
is indicated by . As the strength of the signal diminishes, so will the number of vertical
bars in the icon, with no bars indicating no signal.
LEGAL NOTICE: In many countries you are required by law to turn off your phone on
board an aircraft. Turning off the power of your Pocket PC Phone doesn't turn off the
phone function. You must turn on the Flight Mode in order to disconnect the connection
to the wireless network.
Pocket PC Phone User Manual
45
Turning on the Flight Mode
To turn OFF your wireless connection to an active network, you can switch your phone
connection mode to Flight mode. You can turn the Flight Mode On or Off while keeping
your Pocket PC Phone turned ON.
1. While using any program on your Pocket PC Phone , tap
the phone’s display.
in the title bar at the top of
2. Tap the Turn on flight mode or Turn off flight mode option in the pop-up dialog box.
3. Select the Turn off flight mode to receive calls.
You can use any programs on your device during a call. To quickly switch back to the
Phone Dialer Screen, tap
, or tap the Start menu > Phone.
Adjusting the phone volume:
1. During a call, tap
or press the volume buttons on the side of your device.
2. You can select to adjust the phone volume
levels and MP3) on the pop-up menu.
3. If you select Vibrate mode,
display.
(ring) or device volume
(notification
will appear in the title bar at the top of the phone
4. Turn off the volume by choosing the Off option.
To adjust the conversation phone volume, you must do it during a call. Adjusting the volume
at another time will affect the ring, notification, and MP3 sound levels.
46
Pocket PC Phone User Manual
3.2 Making a Call
With your Pocket PC Phone , you can make a call from
the Dialer, Contacts, Speed Dial, Call History, and SIM
Manager.
Making a call from the Dialer
The most direct method is by using the Phone keypad.
1. Press
to bring up the dialer screen.
2. Tap the number on the keypad, then tap the Talk button
or press
.
Backspacing and deleting
If you tap a wrong number, you can back space by tapping
the back arrow key to erase individual numbers one at a
time. You can also delete all the numbers in the window by
tapping Edit > Clear from the Dialer screen.
Making a call from Contacts
You can make a call from Contacts in the following
ways:
n Press the Contacts button in the upper left corner of
your Pocket PC Phone .
n Find the contact, and then press the
button twice
(Once to send to the dialer screen and once to call).
n Tap
at the bottom of the Dialer screen. This will
invoke Contacts. Select a contact in the contact list,
and then press
twice.
Pocket PC Phone User Manual
47
A pop-up number right after pressing the
will call the Work Tel by default. However,
you can customize it so that the mobile number or E-mail is displayed instead.
n In the Contacts list, tap the w in the right column
next to the contact you want to customize. A pop-up
menu will display the phone numbers and E-mail
addresses for this contact with a dot next to the
priority number.
Tap the w here to pop-up all the
phone numbers and E-mails for
this contact
n In the pop-up menu select a priority. If you selected a
mobile number, m should now be in the right column
next to the contact.
n When pressing the Left or Right button on the
navigation pad, the number of the selected contact
on the screen will change, displaying the mobile
number, work number, or E-mail in turn.
Making a call from Call History:
1. In the Dialer screen mode, tap
pad.
, or just press the Right button on the navigation
2. Find the call details by first selecting the category it is filed under. For example, if it is in All
calls, select All calls from the drop down menu in the top-left corner.
3. Use the navigation pad to find the number and then tap
number you wish to call.
or the icon to the left of the
Call History icons include:
Incoming calls.
Outgoing calls.
Missed calls.
48
Pocket PC Phone User Manual
Making a call from Speed Dial
Create Speed Dial to call frequently-used numbers with a single tap. The number must
already exist in Contacts before you can create a Speed Dial entry.
1. From the Phone keypad, tap
> New.
2. Tap the desired contact name and number.
3. In the Location field, tap the Up/Down arrows to select an available location to assign as
the new Speed Dial entry. (The first Speed Dial location is reserved for your voice mail).
By memorizing the position in the Speed Dial list of a number, you can dial the number by
pressing and holding its position number. By default the Location function will give you the
next available position in the Speed Dial setting screen. If you want to put a number in a
position that is already occupied, the new number will replace the number already there.
Tips for using Speed Dial
To create a Speed Dial entry from Contacts, tap and hold the contact name > Add to
Speed Dial > Up/Down arrows to select an available location to assign as the new speed
dial entry.
To delete a Speed Dial entry, go to the Speed Dial list, tap and hold the contact name in
the box to the right of the assigned speed dial number, and then tap Delete.
Checking your Voice Mail
By default, the first Speed Dial location is your voice mailbox. When you insert your SIM
card into your Pocket PC Phone , it will automatically detect and set, by default, the voice
mailbox number of your service provider.
Pocket PC Phone User Manual
On the Phone Dialer screen, tap
select
Voice Mail, and then press
49
or press the Left button on the navigation pad,
.
Making a call from SIM Manager
SIM Manager allows you to view the contents of your SIM card, transfer contacts to
Contacts on your Pocket PC Phone , and make a call from SIM.
1. Tap the Start menu > Programs > SIM Manager. Wait for your SIM card contents to
load.
2. Tap and hold the name or phone number of the person you wish to call, and then select
Call from the pop-up menu.
3.3 Smart Dialing
Smart Dialing is an application that makes it easy for you to dial a phone number on
your Pocket PC Phone Phone Edition. Smart Dialing searches the Phonebook entries
in both the SIM card and Pocket Contacts, as well as numbers in Call History (Incoming,
Outgoing, or Missed). As soon as you start entering numbers, Smart Dialing starts looking
for matches, and lists them in the Smart Dialing window in the upper left area of your
screen. Both Portrait and Landscape orientations are supported.
Starting Smart Dialing
Smart Dialing starts running along with Microsoft Phone Dialer automatically, as soon as
you start dialing a number.
To open the Phone screen,
n Select Phone from the Start Menu,
n Or press the Talk button.
50
Pocket PC Phone User Manual
Tap the first digit of the number you want to dial. The Smart Dialing window will then
appear in the upper left area of the Phone screen.
How the matching numbers works
Smart Dialing starts looking for numbers that match the sequence you have entered
thus far. It looks for matches in your SIM card, Pocket Contacts, and Call History.
Matching is performed according to both the number and the letter associated with the
selected button on the keypad.
Each time you tap an additional digit or delete a digit, the search is renewed and the
result is re-displayed. The list may include phone numbers and/or Contact names
associated with matching number sequences.
Tap the Talk button to dial
Making a call or sending a text message
To browse the result after you tap in some digits,
n Tap
or
, located at right side of the result list.
n Or press up/down buttons on navigation pad.
The selected contact is higihlighted in gray.
Pocket PC Phone User Manual
To see more matched contacts, tap
51
.
To call selected contact,
n Tap Talk button on the Phone pad.
n Or press Talk/Send button.
If a contact number has display, this contact has more than one phone numbers. To call
selected contact with a different phone number,
n Tap and hold the selected contact to display a pop-up menu, then tap on the
desire phone number to call.
n Or press Left/Right buttons on navigation pad to select desire phone
number, then tap Talk button on the Phone pad or press Talk/Send button to
call.
To send a text message to the selected contact, tap and hold the selected contact to
display a pop-up menu, then tap on the Send Text Message.
To view or edit selected contact's detailed information (only contacts stored in Contacts),
n Tap and hold the selected contact to display a pop-up menu, then tap on the
contact's name.
n Or press Action button.
Smart Dialing Options
This feature lets you select various options for Smart Dialing. You can invoke the Smart
Dialing Options screen by selecting Tools > Smart Dialing Options from the Phone
screen.
Here are the list of Smart Dialing options:
52
Pocket PC Phone User Manual
Enable Smart Dialing
Check this box to automatically enable Smart Dialing
each time you make a call.
Enable drag-scroll
Check this box to scroll the list of matched items.
Enable double-click for
dialing
Check this box to call a number from the list by tapping
twice on it.
Display numbers in
standard format
Check this box to display numbers formatted with
standard characters such as hyphen, parantheses, and
space.
Scroll unit
Choose to scroll by One line, Half page, or One page.
This option only affects and buttons.
3.4 Receiving a call
Answering an incoming call
When you receive a phone call, a message will appear, giving you an option to either
answer or ignore the incoming call.
1. Tap Answer, or press
.
2. Tap Ignore or press
to silence the phone and reject the call. This may route the call
to your voice mail, depending on your service provider.
Ending a call
Once an incoming or outgoing call is in progress, you can press
the Dialer screen to hang up.
, or tap
on
Pocket PC Phone User Manual
53
3.5 In-Call Options
Putting a call on hold
Your Pocket PC Phone notifies you when you have another incoming call and gives you the
choice of rejecting or accepting the call. If you accept, you can choose to switch between
the two callers or set up a conference call between all three parties.
1. Tap Answer to take the 2nd call and put the 1st one on hold.
2. To end the 2nd call and go back to the 1st one, tap
or press
.
Swapping between calls
You can choose to switch between 2 callers by pressing
.
Setting up conference calls:
1. Either put a call on hold, dial a 2nd number and wait for it to be picked up. Or, accept a 2nd
incoming call when you already have one in progress.
2. In the screen that appears tap
.
3. If the conference connection is successful, the word Conference will appear at the top of
the Phone Dialer screen.
4. To add additional people to your conference call, tap
tap
to return and continue.
enter the number, and then
Making notes during a call
Regardless of whether you call from the Phone Dialer, Contacts, Call History, Speed
Dial or SIM Manager, you can take notes during a call. After you have finished the note,
it will be saved as an attachment to your call in one of the Call History folders.
54
Pocket PC Phone User Manual
Writing a note:
1. During a call, just tap the
icon at the bottom of the screen.
2. Use any of the input methods to record your note and then tap OK. You can finish your
note during or after the call.
Viewing a note:
1. In Call History list, tap and hold the desired number, then tap View Note in the pop-up
menu. The
icon indicates a note.
2. Or, go to Notes, and then tap the name of the file in the list. (For more information, see
Chapter 2).
Turning on the speakerphone
Your device has a speakerphone allowing you to talk hands-free or let other people listen
to the conversation.
1. Wait until the phone is ringing.
2. Hold down
bar.
until the speakerphone comes ON and the icon
3. To turn OFF the speakerphone hold down
appears in the status
again.
WARNING: To avoid damage to your hearing, do not leave your Pocket PC Phone on
speakerphone mode and hold it against your ear.
Muting a call
You can mute your microphone during a call so that you can hear the caller without being
heard. From the Phone Dialer keypad, tap
to mute or un-mute a call.
Pocket PC Phone User Manual
55
3.6 Contacts Information
Contacts can be imported in the following ways:
n From your SIM card: Use your SIM card on your Pocket PC Phone and another device;
while using the other device you create one or more new contacts on the SIM card.
n From your Call History: New contact numbers can be found in incoming or missed calls.
Why import contacts?
n Backup your SIM numbers to your Pocket PC Phone .
n When setting Speed Dial numbers, it must be based on those contacts in Contacts, not
on the SIM card.
n Creating contacts in Contacts creates more detailed records.
n While using Photo Contacts, data of contacts fully mirror those in Contacts.
SIM Manager
Creating a SIM contact:
1. To open SIM Manager, tap the Start menu > Programs > SIM Manager. Wait for your SIM
card contents to load.
2. After the SIM contents have loaded, tap New.
3. Fill in the Name and Phone details, tap Add.
Transferring contacts from SIM to Contacts:
On SIM Manager, tap Tools > Select All > Save to Contacts. Press and hold the center
of the navigation pad when a contact has been selected, or tap and hold a contact from
the list. Select Save to Contacts from the pop-up menu.
56
Pocket PC Phone User Manual
Saving your own numbers
You can choose to save your personal phone numbers in a separate screen in SIM
Manager.
1. Tap the Start menu > Programs > SIM Manager >
Tools > List of Own Numbers.
2. Add a number to the screen, and then tap OK.
Call History
Tap
on the phone screen to view the call history list.
Adding a Phone number from Call History to Contacts:
1. Find the call details you want to add.
2. Press and hold the stylus or press and hold the center button of navigation pad. Select
Save to Contacts in the pop-up menu that appears.
3. In the Save to Contacts screen, add additional contact details and press the navigation
pad center or tap OK.
The call details in the Call History will then be amended and displayed under the name,
not the phone number, when the contact is created.
Viewing calls details
Tap in the top left corner of the screen and then select a category from the drop down
menu. Calls are categorized as follows:
Pocket PC Phone User Manual
57
n All Calls: Displays all calls made to and from the phone in chronological order.
n Missed
: Displays calls that were not answered.
n Outgoing
Displays calls made from the phone.
n Incoming
: Displays calls made to the phone.
n By Caller: List calls alphabetically by caller.
Viewing call duration:
Go to Call History, find the call, and then tap once on the time called.
Deleting individual calls:
Tap and hold the stylus on the call to be deleted. Select delete from the pop-up menu.
Deleting all calls:
Tap Tools > Delete all Calls.
Limiting the size of Call History:
Tap
> Tools > Call Timers and then the box under Delete call history items
older than. In the drop-down menu select a time period, then tap OK.
3.7 Photo Contacts
Photo Contacts make your Pocket PC Phone more fun and practical. It allows you to assign still or animated photos to the entries in your Contacts. When a person calls you (for
whom you have previously assigned a photo in Photo Contacts), that photo will appear
on your Pocket PC Phone ’s incoming call screen. Use the rich set of features to get the
photos displayed with the size, position, and animated template you want.
58
Pocket PC Phone User Manual
Creating a new photo contact:
1. Tap the Start menu > Programs > Photo Contacts.
2. Select a contact from the list, or create a new one by tapping Edit > New. Photo Contacts
here fully mirror those in Contacts.
3. Tap Edit > Assign Photo...
4. Tap the field next to Type to select the type of files you want listed, i.e., jpeg, bmp, gif or
all > next to Find in: to select the location of a file. You can use JPEG, BMP, still GIF, or
animated GIF files for your Photo Contacts.
5. Tap a picture file, then OK, and OK again until you return to the Photo Contacts screen.
You can see the photo at the bottom of the screen.
To preview and adjust settings:
In step 5 above, after you tap OK once you will arrive at the preview
and display settings screen. In Display Settings you can:
1. Add extra style by assigning a template to the photo A few sample Photo Contacts
templates (animated graphical templates that can frame your assigned photos) are
included in your Pocket PC Phone 's local storage in the \My Documents\Templates
folder.
2. Choose how you want the photo to fit to the window.
3. Enlarge the photo if it is smaller than the window.
4. Choose a size and position for the picture.
5. View all of these changes by tapping Preview.
Pocket PC Phone User Manual
59
Toolbar Icons
The Toolbar provides a convenient way for you to select frequently-used commands. From
left to right, the functions of the icons on the Toolbar are:
Create a new Contact entry (same as New... on the Edit Menu).
Modify data for the selected Contact entry (same as Edit... on the Edit
Menu).
Delete the selected Contact entry (same as Delete on the Edit Menu).
Assign a Photo ID to a Contact entry (same as Assign Photo... on the
Edit Menu).
Remove a Photo ID assignment (same as Unassign Photo on the Edit
Menu).
Assign a ring tone to a Contact entry (same as Assign Ringtone... on
the Edit Menu).
Remove a ring tone assignment (same as Unassign Ringtone on the
Edit Menu).
Preview the current Photo/template assignment (same as Preview... on
the View Menu).
Invokes “Detailed View” for the current entry (same as Properties... on
the View Menu).
To assign a photo from the camera:
1. Tap the Start menu > Programs > Photo Contacts.
2. Select a contact from the list, or create a new one by tapping Edit, then New. Photo Contacts
here fully mirror those in Contacts.
3. Tap Edit then Assign Photo from Camera.
4. After you take the picture, you will be returned to the Display Settings and Preview
screen.
60
Pocket PC Phone User Manual
To unassign a photo:
1. Tap the Start menu > Programs > Photo Contacts.
2. Select an existing contact entry that you want to remove.
3. Tap Edit > then Unassign Photo. Tap yes in the pop-up box.
To view your contacts by photo:
1. Tap the Start menu > Programs > Photo Contacts.
2. Tap the Dialer View icon. Or, tap View > Photo Dialer View.
In the Photo Dialer view mode, the View Menu contains three additional commands
that allow you to specify the size of the thumbnail images: Large Thumbnails, Normal
Thumbnails and Small Thumbnails. You can enter the Detailed View of Photo Contact
using any of these methods:
n Select the desired Contact entry > Properties... on the View Menu.
n Select the desired Contact entry > the Properties icon on the Toolbar.
n Select the desired Contact entry > the Action button on your Pocket PC Phone .
n Double-tap a Contact entry.
To disable the display of photos during incoming calls:
1. Tap the Start menu > Programs > Photo Contacts.
2. Tap Tools > Options. Uncheck the Display photo during incoming or waiting call box.
(Photo ID for each contact will still display in the Contacts list).
Pocket PC Phone User Manual
61
To manage your groups
You can create a new group, rename, delete, and assign and unassign a photo to a group
by tapping Tools > Manage group.
To assign a contact to a group:
1. Tap the Start menu > Programs > Photo
Contacts.
2. Select a contact from the list, or create a new
one by tapping Edit, then New. Contacts
here fully mirror those in Contacts.
3. Tap Edit > Assign Group.
4. Select a group from the list, then tap OK.
To unassign tap Unassign Group on the Edit menu.
Show Contact Names Only
When Show Contact Names Only is selected on the View menu, only the name of each
Contact entry (no phone number or other data) will be listed. The Photo ID (if any) will
still be displayed.
62
Pocket PC Phone User Manual
Set Default Photos...
The Set Default Photos screen lets you assign, unassign, and preview default Photo
IDs to appear for these three situations:
Unknown
photo
This photo will display whenever the phone number of the incoming call
is not known to Caller ID because no phone number was “passed in”
to your Pocket PC Phone . This would occur if the person calling you
has blocked their phone number from being displayed to the receiver,
or has not enabled the broadcast of their Caller ID.
Not-found
photo
This option in the Set Default Photos screen lets you assign a generic
Photo ID to any incoming call from a person whose number is not found
in your Contacts. That is, the phone number of the incoming call is
known, but has no matching entry in your Contacts.
Default
photo
This photo will display when the incoming call is found to be from
a matching entry in your Contacts database, but so far there is no
individually-assigned Photo ID for either that individual Contact entry,
or for the Group it belongs to.
1. To select Set Default Photos, tap Tools > Set Default Photos.
2. Check a circle next to one of the categories, tap Assign.
3. Select a picture, assign settings.
Pocket PC Phone User Manual
63
Assign a Ring tone
This feature allows you to assign ring tones to your Contacts entries, or to the
phonebook entries on your SIM.
1. Tap the Start menu > Programs > Photo Contacts.
2. Select the desired contact from the list, or create a new one by tapping Edit >
NEW.
3. Tap Edit > Assign Ring tone, or tap the Assign Ring tone icon in the toolbar.
4. Tap Find to list all sound files.
5. Select a sound file, and tap OK to assign it as a ring tone to the selected contact.
To unassign a ring tone:
1. Tap the Start menu > Programs > Photo Contacts.
2. Select an existing contact entry that you want to remove.
3. Tap Edit > Unassign Ring tone, or tap the Unassign Ring tone icon in the toolbar.
Preview
This feature allows you to preview the Photo ID and ring tone you have assigned to a
contact.
1. Tap View > Preview, or tap the Preview icon in the toolbar.
2. Select View > Play Ring tone during Preview to play the ring tone assigned
to the contact .
64
Pocket PC Phone User Manual
3.8 Additional Dialing Information
Making an emergency call
Enter the international emergency number 112, then tap
or press
.
Additional emergency numbers may be included on your SIM card. Contact T-Mobile for
more information.
Making an international call:
1. Tap and hold the
key until the + sign appears. The
prefix of the country where you are calling.
+ replaces the international
2. Enter the full phone number you want to dial. It includes country code, area code (without
the leading zero), and phone number.
3. Tap
or press
.
SIM Tool Kit
This feature allows you to access a range of information services provided by your operator.
1. Tap the Start menu > Programs > STK.
2. A List of services provided by your operator should appear on the page.
3. To access a service, tap on any item in the list.
Be sure a SIM card is inserted in your phone when accessing SIM Tool Kit (STK).
Pocket PC Phone User Manual
65
3.9 Securing Your Pocket PC Phone
You can customize the level of security you want to have on your Pocket PC Phone by
locking the keypad, the entire device, or the SIM card.
Locking the keypad
The keypad lock turns off the keypad functionality. This is a helpful feature if, for example,
your Pocket PC Phone is turned off and in your pocket, and you want to prevent accidental keypress.
1. Tap the Start menu > Settings > System tab > Button Lock.
2. Select Lock all buttons except Power button.
3. To unlock your keypad, tap Do not lock buttons.
Locking your Pocket PC Phone
Locking your Pocket PC Phone prevents access to personal data. When you enable this
feature, your Pocket PC Phone will automatically lock after a specified time of inactivity.
A screen will be displayed requiring your Pocket PC Phone "lock password" to be entered
before access is granted.
1. Tap the Start menu > Settings > Personal > Password.
2. To enable this function, select how long your mobile device must be turned off before the
password is required for using the device, by tapping Prompt if device unused for.
3. Select the type of password you would like to use: Simple 4 digit or Strong alphanumeric.
A strong password must have at least 7 characters that are a combination of uppercase
and lowercase letters, numerals, and punctuation.
4. Enter the password, and if necessary, confirm the password.
NOTE: To unlock your Pocket PC Phone , uncheck Prompt if device unused for.
66
Pocket PC Phone User Manual
Locking the SIM card
You can protect your Pocket PC Phone from unauthorized use by assigning a PIN (Personal Identification Number). Your first PIN is assigned by T-Mobile.
1. On the Pocket PC Phone keypad, tap Tools > Options > Phone tab.
2. Select Require PIN when phone is used.
3. To change the PIN at any time, tap Change PIN.
Chapter 4
Synchronizing Information
4.1 Using ActiveSync
4.2 Synchronizing Information
4.3 Infrared and Bluetooth Connection
4.4 ActiveSync Errors
68
Pocket PC Phone User Manual
4.1 Using ActiveSync
With ActiveSync on both your PC and your Pocket PC Phone, you can exchange
information between a PC or server and your Pocket PC Phone. This process is called
"synchronization." To synchronize your Pocket PC Phone with your PC, you must install
ActiveSync on the PC. Using ActiveSync, you can:
n Synchronize information between your Pocket PC Phone and PC or server so that you
have the latest information in all locations.
n Change synchronization settings and synchronization schedule.
n Copy files between your Pocket PC Phone and PC.
n Back up and restore information saved on your Pocket PC Phone.
n Add and remove programs on your Pocket PC Phone.
By default, ActiveSync does not automatically synchronize all types of information. Use
ActiveSync options to turn synchronization on and off for specific information types.
You can synchronize information between your mobile device and a server if your company
is running Microsoft Exchange Server with Exchange ActiveSync.
Installing ActiveSync
Before you begin synchronization, install ActiveSync on your PC from the Application
CD. ActiveSync is already installed on your Pocket PC Phone.
Once ActiveSync is installed on your PC, you will be prompted to connect and create a
partnership with your Pocket PC Phone by using a cable, cradle, infrared, or Bluetooth
connection.
Pocket PC Phone User Manual
69
Connecting to a PC via a cable or cradle
Please see the Quick Start Guide for information about ActiveSync installation.
1. Connect your Pocket PC Phone and PC via a cable or cradle to start synchronization.
2. Your first synchronization will automatically begin when you finish the installation wizard.
After the first synchronization, you will notice that your Outlook information now appears
on your Pocket PC Phone.
3. To disconnect, remove your Pocket PC Phone from the cradle or detach it from the
cable.
View connection status
Stop sync
Connect and
synchronize
Synchronize via IR or change
synchronization settings
Connecting to a PC by Infrared
You can use an infrared connection to create a direct connection between your Pocket
PC Phone and another IR-enabled mobile device or PC quickly. This method is ideal
for quickly switching between multiple devices since there are no cables or adapters
to change. When creating a partnership, you must connect using infrared, a cable,
or a cradle connection.
70
Pocket PC Phone User Manual
1. Set up an infrared connection. (Install and configure an infrared port on your PC according
to the manufacturer's instructions).
2. Switch to the infrared port on your desktop computer: On the File menu of the ActiveSync
on your PC, click Connection Settings. In the Allow serial cable or infrared connection
to this COM port list, select Infrared Port (IR).
3. Align the infrared ports on your PC and your Pocket PC Phone so that they are unobstructed and within close range.
4. On your Pocket PC Phone, tap the Start menu > ActiveSync > Tools > Connect via
IR.
4.2 Synchronizing Information
This section provides an overview of the types of Outlook information you can synchronize.
By default, ActiveSync does not automatically synchronize all types of Outlook information.
Use ActiveSync options on your PC to turn synchronization on and off for specific
information types.
Synchronizing Outlook E-mail
After selecting Inbox for synchronization in ActiveSync, Outlook E-mail messages are
synchronized as part of the general synchronization process. During synchronization:
n Messages are copied from the Inbox folder on your PC or the Microsoft Exchange server to
the Inbox folder of the Outlook E-mail account on your device. You can only synchronize
information directly with an Exchange Server if your company is running Microsoft Mobile
Information Server 2002 or later. By default, you’ll receive messages from the last three
days only, the first 100 lines of each new message, and file attachments of less than
100KB in size.
n Messages in the Outbox folder on your device are transferred to Exchange or Outlook
and then sent from those programs.
n The messages on the two computers are linked. When you delete a message on your
device, it’s deleted from your PC the next time you synchronize.
n Messages in subfolders in other E-mail folders in Outlook are synchronized only if they
have been selected for synchronization in ActiveSync.
Pocket PC Phone User Manual
71
For information on initiating Outlook E-mail synchronization or changing synchronization
settings, see ActiveSync Help on the PC or Connections Help. Text messages (SMS)
and Media messages (MMS) are not received through synchronization. Instead, they are
sent to your device via your service provider.
Synchronizing Calendar
n Calendar items stored on your Pocket PC Phone can be synchronized with calendar items
on your PC or Microsoft Exchange Server. You can only synchronize information directly
with an Exchange Server if your company is running Microsoft Mobile Information Server
2002 or later. Calendar synchronization is automatically selected in ActiveSync.
n Calendar items entered on one computer are copied to the other during synchronization.
Handwritten notes and drawings are saved as metafiles (pictures).
Synchronizing Contacts
n Contacts stored on your Pocket PC Phone can be synchronized with Outlook contacts
stored on your PC or with Mobile Information Server 2002 or later.
n New items entered in one location are copied to the other during synchronization.
Handwritten notes and drawings are saved as pictures when synchronizing with your
PC, but are removed when synchronizing with a server. For more information on
synchronization, see ActiveSync Help on the PC.
72
Pocket PC Phone User Manual
Synchronizing Tasks
n Tasks stored on your device can be synchronized with Outlook on your PC. Task
synchronization is automatically selected in ActiveSync.
n New items entered on one computer are copied to the other during synchronization.
Handwritten notes and drawings are saved as metafiles (pictures). For more information
on synchronization, see ActiveSync Help on the PC.
Synchronizing Notes
Notes can be synchronized between your PC and Pocket PC Phone either through notes
synchronization or file synchronization. Notes synchronization synchronizes the notes on
your Pocket PC Phone with Outlook Notes on your PC. File synchronization synchronizes
all notes on your Pocket PC Phone with the My Documents folder on your PC.
To synchronize your notes through notes synchronization, first select the Notes information
type for synchronization in ActiveSync. The next time you synchronize, all notes in My
Documents and its subfolder on your device will appear in Outlook Notes on your PC.
Notes that contain only text will appear as regular notes in Outlook on your PC, while
notes containing written text or drawings will appear in the device format. In addition, all
notes in the Notes group in Outlook on the PC will appear in Notes on the device.
To synchronize your notes as files, in ActiveSync, select the Files information type
for synchronization and clear the Notes information type. When you select Files, the
My Documents folder is created on your PC’s desktop. All .pwi files placed in the My
Documents folder on your device and all .doc files placed in the \My Documents folder
on your PC will be synchronized. Password-protected files cannot be synchronized.
ActiveSync converts documents during synchronization. For more information on
synchronization or file conversion, see ActiveSync Help on the PC.
NOTE: When you delete or change an item on either your PC or device, the item is changed
or deleted in the other location the next time you synchronize.
If you synchronize your notes using file synchronization and then later decide to use notes
synchronization, all of your notes will be synchronized with Outlook on your PC and will
no longer be stored in the My Documents folder.
Pocket PC Phone User Manual
73
4.3 Infrared and Bluetooth Connection
Infrared
You can use infrared (IR) to send and receive information and files between mobile devices.
If an IR port is installed on your PC, you can send and receive information and files between
your Pocket PC Phone and PC. On your Pocket PC Phone, tap the Start menu > Settings
> the Connections tab > Beam.
By default your device detects incoming infrared (IR) and Bluetooth beams and prompts
you to accept them. If you do not want your Pocket PC Phone to detect or receive beams,
clear the Receive all incoming beams check box.
NOTE: If someone attempts to send you an IR beam from an older device, you may not
be prompted to accept it. In this case, before the beam is sent from the other device, tap
Receive an infrared beam at the bottom of the Beam screen.
Bluetooth
1. Make sure that your Pocket PC Phone is configured to receive incoming beams.
2. Make sure that your Pocket PC Phone is turned on, discoverable, and within 10 meters
(about 30 feet) of the other device beaming the information.
3. When prompted to receive an incoming beam, tap Yes to accept the beam.
For more information about Bluetooth and its settings, please see Chapter 6.
74
Pocket PC Phone User Manual
4.4 ActiveSync Errors
Whenever ActiveSync cannot successfully synchronize your information, it displays an
error on your Pocket PC Phone.
Viewing error information
Press the Action button when the error text is displayed. ActiveSync will then display
more information about the error that occurred.
Some types of errors can interfere with automatic synchronization. If you suspect that a
scheduled automatic synchronization has not occurred, you should attempt to manually
synchronize your information. Successfully completing manual synchronization will reset
automatic synchronization. For more information, see the Synchronizing Information
section of ActiveSync Help on your PC.
Chapter 5
Personalizing Your Pocket
PC Phone
5.1 Device Settings
5.2 Phone Settings
76
Pocket PC Phone User Manual
5.1 Device Settings
You can adjust the device settings to suit the way you work. To see available options, tap
the Start menu > Settings > the Personal tab or System tab located at the bottom of
the screen.
The Personal tab
Icon
Program
Button
Assigns an application program to a hardware button.
Input
Sets up the input portion of your device.
Menus
Customizes the menu appearance and enables a pop up menu from the New
button.
Owner Information
Displays your contact information.
Password
Limits access to your device.
Phone
Sets up the phone function of your wireless
feature.
Sounds & Notifications
Sets the notification type, event and volume.
Today
Customizes the look and the information that appears on the Today screen.
Pocket PC Phone User Manual
The System tab
Icon
Program
About
Displays important device information.
Add Ring Tone
To listen to and select new ring tones.
Backlight
Customizes the backlight and brightness for power saving purposes.
Button Lock
Enables you to lock the buttons on your device except Power button when device
is off.
Certificates
Displays the name of the certificate issuer and the expiration date.
Clock & Alarms
Changes the time and sets alarms.
Device information
Find information about version, hardware, identity, and call duration.
Keyboard
Allows you to customize the keyboard settings, e.g., to switch on/off the keyboard
backlight when a time limit is reached.
Memory
Displays the memory allocation status and current running programs.
Microphone AGC
Adjusts the volume automatically when you are recording.
Permanent Save
Saves contacts to permanent flash memory.
Power
Maximizes battery life.
Regional Settings
Customizes the region and relative format for the region you use.
77
78
Pocket PC Phone User Manual
Icon
Program
Remove Programs
Creates more memory by removing programs.
Screen
Re-calibrates the screen and enables/disables Clear Type feature.
Buttons
To customize the program hardware buttons to open your most frequently-used
programs:
1. Tap the Start menu > Settings > the Personal tab > Buttons > the Program Buttons
tab.
2. Under Select a button, tap the button you want to assign a program, and then select a
program from Assign a program.
Default settings:
1 - Contacts
2 - Calendar
3 - Camera
4 - Record
3
1
2
4
In the Up/Down Control tab, Delay before first repeat changes the time elapsed before
scrolling begins. Repeat rate changes the time it takes to scroll from one item to the next.
Press and hold the Up/Down control to scroll through the items in a list to adjust.
Input
1. Tap the Start menu > Settings > the Personal tab > Input.
2. On the Input Method tab, select an input method and change desired options. On the Word
Completion tab, select the desired settings for word completion. On the Options tab, select
the desired options for writing and recording. These options apply to any program on the
Pocket PC Phone User Manual
79
device where you can record or write. These options do not apply to text you enter using
the input panel.
You can also change input options by tapping the
arrow and Options.
Menus
Only 7 programs are allowed in the Start Menu. To add the programs you use most often
to the Start menu:
1. Tap the Start menu > Settings > the Personal tab > Menus.
2. Select the programs you want, then tap OK.
3. On the New Menu tab, you can select Turn on New button menu and then select the items
to appear on the menu. When you do this, an arrow appears next to New in the command
bar of certain programs such as Pocket Word, Pocket Excel, Contacts, Calendar and
Tasks. You can tap this arrow and then tap a new item to create.
You can create subfolders and shortcuts to appear under the Start menu. In ActiveSync
on your PC, click Explore > My Pocket PC Phone > Windows > Start Menu.
Owner Information
1. Tap the Start menu > Settings > the Personal tab > Owner Information.
2. On the Identification tab, enter your personal information.
On the Notes tab, enter any additional text you want to display when the device is turned
on, such as: "Reward if found."
On the Options tab, select Identification Information so that if you lose your device, it can
be returned to you.
Password
A strong password must have at least 7 characters that are a combination of uppercase
and lowercase letters, numerals, and punctuation.
1. Tap the Start menu > Settings > the Personal tab > Password.
80
Pocket PC Phone User Manual
2. To enable this function, select how long your mobile device must be turned off before the
password is required for using the device by tapping Prompt if device unused for.
3. Select the type of password you would like to use: Simple 4 digit or Strong
alphanumeric.
4. Enter the password and, if necessary, confirm the
password.
n If your device is configured to connect to a network, use a strong password
to help protect network security.
n If you forget your password, you must clear the memory before you can access
your device. This will erase all files and data you have created and programs
you have installed. For more information about clearing memory, please see
Appendix A.
n If you've used ActiveSync to create a backup file, all of your program data
can be restored. For more information on creating a backup file, also see
Appendix A.
Sounds and Notifications
Turning off sounds and the notification light helps conserve battery power. To change the
ring type and volume:
1. Tap the Start menu > Settings > the Personal tab > Sounds & Notifications.
2. On the Sounds tab, you can select the desired actions.
3. On the Notifications tab, you can customize how you are notified about different events.
Select the event name and then select the type of reminder. You can select a special sound,
a message, or a flashing light.
Today
Changing the background:
1. Tap the Start menu > Settings > the Personal tab > Today.
Pocket PC Phone User Manual
81
2. On the Appearance tab, select the desired theme for the background. To use your own
background, select Use this picture as the background then tap Browse to locate the
desired file.
3. Choose a folder and tap the file you want, then tap OK.
NOTE: The recommend picture size for the background is 240x320 pixels in jpeg file
format. To beam a favorite theme to a friend, select the desired theme, and tap Beam on
the Appearance tab
Customizing the displayed information:
1. Tap the Start menu > Settings > the Personal tab > Today > the Items tab.
2. Select the information you want displayed on the Today screen.
3. To customize the information further, select an information type, and then tap Options
(not available for all information types).
About
The Version tab displays important device information, including the amount of memory
installed. On the Device ID tab, you may need to change the device name if you are
unable to connect to a network because another device with the same name is already
connected.
82
Pocket PC Phone User Manual
Backlight
Using the backlight on battery power substantially reduces battery life. Tap the Start menu
> Settings > the System tab > Backlight.
n Tap the Battery power tab to turn ON/OFF the backlight when using battery power.
n Tap the External power tab to turn ON/OFF the backlight when using external power.
n Tap the Brightness tab to adjust the brightness level.
Clock & Alarms
Tap the Start menu > Settings > the System tab > Clock & Alarms.
n If you visit a particular time zone often, select it as your Visiting time zone on the
tab so that you can quickly see the correct date and time.
Time
n You can use your device as a travel alarm clock by setting a wake-up alarm on the Alarms
tab. Tap the alarm icon to select the type of alarm you want.
n To change the way the date or time is displayed on your Pocket PC Phone, go to Regional
Settings by tapping the Start menu > Settings > the System tab > Regional Settings.
Memory
You may need to stop a program if it becomes unstable or the program memory is low.
Tap the Start menu > Settings > the System tab > Memory.
n The Main tab displays the amount of memory the system has allocated to file and data
storage versus program storage. This tab also displays the amount of memory in use versus
the available memory. For information about making memory available, see Appendix A.
Pocket PC Phone User Manual
83
n The Storage Card tab displays how much memory is available on the storage card that
is inserted into your device. If you have more than one card inserted, tap the list box and
then the name of the storage card whose information you want to view.
n The Running Programs tab displays the list of currently active programs. You can stop a
program by selecting it in the list and then tapping Stop or just tap Stop All to stop all the
running programs.
You may need to stop a program if it becomes unstable or the program memory is low.
Power
Tap the Start menu > Settings > the System tab > Power.
n The Battery tab displays the amount of battery power remaining. Battery power depends
on the battery type and how the device is being used.
n On the Advanced tab, you can select options for turning off your device to conserve battery
power. To conserve the most power, select the option that turns off the device after 3 minutes
or less.
Permanent Save
You can choose to back up Contacts and Appointments, Tasks, and Connection Setting to non-volatile memory. Backing them up in this way means they will not be lost in the
event your device loses all power and you have to perform a full reset.
To back up to FlashROM:
1. Tap the Start menu > Settings > the System tab > Permanent Save.
2. Select the desired item by checking the boxes. Tap OK.
When you elect to back up Contacts and Appointments, your Pocket PC Phone will
automatically back up newly added contacts, appointments or tasks items. This will not
happen for connection settings if you add new connections you will need to back it up
manually.
84
Pocket PC Phone User Manual
To restore to FlashROM:
1. Tap the Start menu > Settings > System tab > Permanent Save.
2. Select the desired item by checking the boxes > OK.
5.2 Phone Settings
You can easily view and change settings, such as the ring type and ring tone to be used
for incoming calls, and the keypad tone to be used when entering phone numbers. You
can also protect your phone from unauthorized use. There are two ways to change phone
settings:
n Tap the Start menu > Settings > the Personal tab > Phone.
n To change the phone settings from the Phone keypad, tap Tools > Options.
Ring type
You can change the way that you are notified of incoming calls. For example, you can
choose to be notified by a ring, a vibration, or a combination of both. Tap the Ring type
list, and select the desired option.
Ring tone
Tap the Ring tone list, then select the sound you want to use.
n To set .wav or .mid files as ring tones, use ActiveSync on your PC to copy the file to the
\Windows\Rings folder on your device. Select the sound from the Ring tone list.
n To download ring tones, you can make a connection to the Internet and then download
ring tones that are compatible with the .wav or .mid formats.
Pocket PC Phone User Manual
85
Add ring tone
Add Ring Tone allows you to quickly find and display all the ring tones stored on your
device, gives you the option to listen, add, or remove them from the Phone Settings list
mentioned above.
1. To display all ring tones on your device, you can tap the Start menu > Settings > System
> Add Ring Tone. The program will automatically list and display all the .wav and .mid
files on your Pocket PC Phone.
2. After the ring tones have loaded, you can see that some are already selected. These ones
are presently listed in the phone settings.
3. To play a ring tone, select one by tapping it, and then tap play. If you don’t like the ring
tone, deselect it. This will add/remove the selected/deselected ring tones from the list in
your phone settings.
Keypad tone
You can change the tone you hear when entering a phone number on the keypad. If set to
Tones, the tone is heard continuously for as long as the number on the keypad is pressed.
If set to Beep, the tone is heard only for one or two seconds.
1. Tap the Keypad list, then select the option you want.
2. To prevent tones from being heard when entering a phone number, select Off.
Network
With network settings, you can view available networks, determine the order in which your
Pocket PC Phone accesses another network if the current one is unavailable, and specify
whether you want to change networks manually or automatically. The current network will
remain active until you change it, lose your signal, or change your SIM card.
n The network currently in use will be listed at the top of the screen.
n When your current network is unavailable, tap Select Network to select an alternate.
86
Pocket PC Phone User Manual
Services
The Services tabs are primarily used to set options for incoming calls, such as Call
Forwarding, Call Waiting, and Caller ID. To change service settings from the phone dial
screen, tap Tools > Options > the Services tab > select a service > Get Settings.
Feature
Function
Call Barring
Blocks incoming and/or outgoing calls.
Caller ID
Identifies caller by displaying their name and/or phone number.
Call Forwarding
Forwards all or selected incoming calls to a different number.
Call Waiting
Notifies of an incoming call while you are on the phone.
Voice Mail/SMS
Shows the correct numbers in the phone settings.
More
On the More tab, you can access the settings for Automatic Pickup, and Broadcast
Channels.
You can choose to receive real time news and information such as traffic and weather
reports by enabling the Broadcast Channels. This service is dependent on your mobile
service operator.
Chapter 6
Getting Connected
6.1 About Connections
6.2 Connecting to the Internet
6.3 CSD Line Type
6.4 Pocket Internet Explorer
6.5 Network Cards Settings
6.5 Terminal Services Client
6.7 Bluetooth
6.8 Wireless Modem
88
Pocket PC Phone User Manual
6.1 About Connections
This device is equipped with powerful networking functions that allow you to connect to
the Internet through a GPRS network or a Bluetooth modem. You can also use an external
modem with this device to access the Internet.
You can set up connections to the Internet and to a corporate network at work to browse
the Internet, send and receive E-mail, use instant messages, and synchronize with
ActiveSync.
Your Pocket PC Phone has two groups of connection settings: My ISP and My Work
Network. My ISP settings are used to connect to the Internet, and My Work Network
settings can be used to connect to any private network, such as a corporate network. Fill
in the settings and you are ready to connect to the Internet.
6.2 Connecting to the Internet
You can use My ISP settings to connect to the Internet and use different connection methods
to send and receive E-mail messages and surf the Internet.
Pocket PC Phone User Manual
89
Connect to the Internet via an ISP:
1. Obtain the following information from your ISP (Internet Service Provider):
n ISP server phone number.
n User name.
n Password.
n Access point name. (Required for GPRS connection).
2. Tap the Start menu > Settings > the Connections tab > Connections.
3. To create a new connection in My ISP, tap Add a new modem connection, and follow the
instructions in the Make New Connection wizard.
4. Wireless connections can be made via a mobile phone network or GPRS. If you are using
a mobile phone network to connect, tap Cellular Line in the Select a modem list. If you
are using GPRS, tap Cellular Line (GPRS).
n To view additional information for any screen, tap
.
n To start the connection, switch to Pocket Internet Explorer and browse to a Web
page. Your device will automatically connect.
To change modem connection settings, in either My ISP or My Work Network, tap Manage
existing connections. Select the desired modem connection, tap Settings, and follow
the instructions on the screen.
Connecting to a private network
1. Obtain the following information from your network administrator:
n Server phone number.
n User name.
n Password.
2. Tap the Start menu > Setting > the Connections tab > Connections.
3. In My Work Network, follow the instructions for each type of connection.
4. To start the connection, start using a related program. For example, switch to Pocket
Internet Explorer and browse to a Web page. Your device will automatically connect.
90
Pocket PC Phone User Manual
6.3 CSD Line Type
This program allows you to choose the line type when you make a circuit switch data
connection.
To change a CSD Line type:
1. Tap the Start menu > Settings > Connections > CSD Line Type.
2. In Data rate, select a value. In Connection element, choose a type from that drop-down
menu. Tap OK.
NOTE: The default setting on your Pocket PC Phone is set for the most optimal use. Do
not change this setting unless you have trouble using the circuit switch data connection.
GPRS Settings
This program allow you to choose the GPRS setting method when you make a GPRS
connection. Choose between these two required authentication methods:
n PAP authentication: Password Authentication Protocol is a simple authentication
protocol used to authenticate a user to a remote access server of an ISP (Internet Service
Provider).
n CHAP authentication: Challenge Handshake Authentication Protocol is used to
negotiate the most secure form of encrypted authentication supported by both server
and client.
NOTE: Changing these settings may cause your data communications to no longer operate.
Please consult your service provider before altering these settings.
Pocket PC Phone User Manual
91
6.4 Pocket Internet Explorer
Once connected, you can use Pocket Internet Explorer to surf the Internet. While surfing,
you can also download files and programs to be installed on your device from the Internet
or intranet. During synchronization with your PC, download your favorite links and mobile
favorites that are stored in the Mobile Favorites folder in Internet Explorer on the PC. To
synchronize and download your favorite links from your PC, in your PC's ActiveSync,
select, Favorites in the Tools Menu > Options > Sync Options.
Browsing the Internet
Open the Pocket Internet Explorer screen by tapping the Start menu > Internet
Explorer.
1. In the address bar that appears at the top of
the screen, enter the Web address you want to
connect to. Tap the down arrow to choose from
previously entered addresses.
2. Tap
to go to the web address you entered.
3. Tap
to go back to the previous page.
4. Tap
to refresh the web page on the screen.
5. Tap
to go back to the Home page.
6. Tap
(the Favorites button), then tap the
favorite address you want to view. To add a
favorite link while using your Pocket PC Phone,
go to the page you want to add, tap and hold on
the page, and tap Add to Favorites on the popup menu.
1
2
3
4
5
6
92
Pocket PC Phone User Manual
6.5 Network Cards Settings
Use a network (Ethernet) card to connect directly to a network. Once connected, you can
view the Internet or intranet, or download e-mail. Make sure to purchase and configure a
network card that is compatible with your Pocket PC Phone.
To setup your network card:
1. Insert the network card into your Pocket PC Phone.
2. The first time you insert the crad. Network Settings will appear automatically. Or to change
later, tap the Start menu > Setting > the Connections tab > Network Cards.
3. To enter specific server information, tap the appropriate adapter.
To start a connection, insert the network card, and begin using a desired program.
To change network card settings:
1. Tap the Start menu > Setting > the Connections tab > Network Cards.
2. In the My network card connects to: drop-down box, tap either The Internet or Work.
If you are connecting to your ISP at home, tap The Internet. If you are connecting to a
private network such as a corporate network at work, tap Work.
3. Tap the appropriate adapter in the Tap an adapter to modify settings: box, the IP address
will now appear in the IP Address box on the IP Address tab.
4. To change TCP/IP settings if your ISP or private network does not use dynamically-assigned
IP addresses, tap Use specific IP address and enter the requested information. Contact
your ISP or network administrator to get the IP address, subnet mask, and/or default gateway
(if needed).
5. To change DNS and WINS settings if your ISP or private network does not use dynamicallyassigned IP addresses, tap the Name Servers tab and enter the requested information.
Servers that require an assigned IP address may also require a way to map computer
names to IP address. DNS and WINS are the resolution options supported on your Pocket
PC Phone.
Pocket PC Phone User Manual
93
6.6 Terminal Services Client
Using the Terminal Services Client, you can log onto a PC running Terminal Services
or Remote Desktop and use all of the programs available on that PC from your mobile
device. For example, instead of running Pocket Word, you can run the PC version of Word
and access all of the .doc files on that PC from your Pocket PC Phone.
Connecting to a Terminal Server
Start a remote connection to the server via a GPRS or Wireless LAN connection:
1. Tap the Start menu > Programs > Terminal Services Client.
2. To connect to a server you have previously connected to, in Recent Servers, tap a server.
To connect to a new server, enter the server’s name in the Server box. Select the Limit
size of server desktop to fit on this screen check box only when using applications that
have been specifically sized for use with the Pocket PC Phone.
3. Tap Connect.
NOTE: If the network administrator has configured Terminal Services Client to reconnect
to disconnected sessions, and you previously disconnected from a Terminal Server without
ending the session, the Terminal Services Client reconnects to that session.
Navigating within Terminal Services Client
Once connected to the server, the PC’s screen may more than fill your mobile device’s
screen. If scroll bars are displayed on the server’s screen, you will see more than one set of
scroll bars on your Pocket PC Phone: one to scroll information on the PC, and one to scroll
the PC display through the Terminal Services window in Terminal Services Client.
To ensure you are scrolling the PC display through Terminal Services Client, use the
five directional buttons at the bottom of the Terminal Services Client screen. To better fit
94
Pocket PC Phone User Manual
information on your mobile device’s screen, select Limit size of server desktop to fit on
this screen. For best effect, programs on the desktop computer should be maximized.
Disconnecting without ending a session
The following commands must be accessed from the Start menu in the Terminal Services
window used to access the PC’s commands. Do not use the Start menu on your Pocket
PC Phone.
1. In the Terminal Services window, tap Start > Shutdown.
2. Tap Disconnect.
If your administrator has configured Terminal Services Client to reconnect to disconnected
sessions, you will be reconnected to this session the next time you connect to this
server.
Disconnecting and ending a session:
1. In the Terminal Services Client window, tap Start > Shutdown.
2. Tap Log Off.
6.7 Bluetooth
Bluetooth is a short-range wireless communications technology. Devices with Bluetooth
capabilities can exchange information over a distance of about 10 meters without requiring
a physical connection.
Unlike infrared, you don't need to line up the devices to beam information with Bluetooth.
The devices only need to be within a range of about 10 meters. You can even beam
information to a device in a different room, as long as it's within range. The software included
with your Pocket PC Phone allows you to use Bluetooth in the following ways :
Pocket PC Phone User Manual
95
n Beam information, such as files, appointments, tasks, and contact cards,
between devices that have Bluetooth capabilities. For example, if you and a
co-worker each have a device with Bluetooth, you can beam items between
your devices, such as files, contact cards, appointments, tasks, and so forth.
n Create a dial-up modem connection between your device and a Bluetooth
phone. You can then use the Bluetooth phone as a modem.
To access to the Bluetooth settings screen :
1. To turn on/off the Bluetooth mode and create a new bond with other device, tap Start
menu > Settings > Connections tab >Bluetooth. Alternatively, you can also tap the small
icon for Bluetooth connection settins in the right lower corner on Today screen.
2. To add an extra layer of security when beaming information with others or to set a Bluetooth
syncronization tap Start menu > Settings > System tab > Bluetooth Settings.
Bluetooth modes
To turn on Bluetooth On
Check Turn on Bluetooth option.
To turn off Blue tooth Off
Uncheck Turn on Bluetooth option.
In this mode, you can neither send nor receive information by using Bluetooth. You might
want to turn the radio off at times in order to conserve battery power, or in situations where
radio use is prohibited, for example on airplanes and in hospitals.
By default the Bluetooth radio is turned off. If you turn it on, and then turn off your
device, the Bluetooth radio also turns off. When you turn on your device again, the
Bluetooth radio automatically turns on .
96
Pocket PC Phone User Manual
NOTE: In a situation where Bluetooth is on but radio is off, it is not possible to turn on
radio. If you wish to turn on radio, turn off Bluetooth first, and then turn on radio.
To make your device discoverable
Check Make this device discoverable to other devices option.
The Bluetooth radio is turned on, and all of the other Bluetooth devices within range (about
10 meters) can detect your device and attempt to beam information to it, establish a bond,
or use a Bluetooth service. In this mode, other devices can detect your device whether or
not a bond has been created; however, in order to receive a beam from another device,
you must accept it on your device.
Other Bluetooth devices can now detect your device and attempt to beam information to
it, establish a bond, or use a Bluetooth service. Note that to receive beamed information,
you must accept it on your device.
Selecting Discoverable also turns on your Bluetooth radio.
If you no longer want your device to be discoverable, uncheck Turn on Bluetooth option
or Make this device discoverable to other devices option to leave the radio on, but not
allow detection by other devices.
Bonds
A bond is a relationship that you create between your Pocket PC Phone and another
Bluetooth device in order to exchange information in a secure manner. Creating a bond
involves entering the same personal identification number (PIN) on the two devices you
want to bond. You need only create a bond once between two devices. Once a bond is
created, the devices recognize the bond and are able to exchange information without
your entering a PIN again.
Pocket PC Phone User Manual
97
a. To create a Bond:
You can create a bond between your device and another device that has Bluetooth. Once
you do this, Bluetooth doesn’t need to be in discoverable mode in order for you to beam
information between the two devices; the Bluetooth radio only needs to be turned on.
1. Make sure that the two devices are within 10 meters of one another and that Bluetooth is
in discoverable mode on both devices.
2. Tap Start menu > Settings > Connections tab.
3. Tap Bluetooth > Devices tab > New. Your device searches for other Bluetooth devices
and displays them in the list.
4. Tap the name of the other device in the list, and then Next.
5. In PIN, enter a PIN of between 1 and 16 characters and tap Next.
6. Enter the same PIN on the other device.
7. If you want, in Name, edit the name of the other device.
8. Tap Finish.
b. To accept a Bond:
1. Make sure that Bluetooth is turned on and in discoverable mode.
2. When prompted to bond with the other device, tap OK.
3. In PIN, enter a PIN of between 1 and 16 characters, and tap Next. You must enter the same
PIN that was entered on the device requesting the bond.
4. If you want, in Name, edit the name of the device requesting the bond.
5. Tap Finish.
The bond is created. You can now exchange information with the other device.
98
Pocket PC Phone User Manual
c. To rename a Bond :
1. Tap Start menu > Settings > Connections tab.
2. Tap Bluetooth > Devices tab.
3. Tap the bond to rename.
4. In Name, enter a new name for the bond.
5. Tap Finish.
d. To delete a Bond :
1. Tap Start menu > Settings > Connections tab.
2. Tap Bluetooth > Devices tab.
3. Tap and hold the bond to delete.
4. Tap Delete.
Beaming Information with Bluetooth
1. Tap and hold an item to beam, such as an appointment in Calendar, a task in Tasks, a
contact card in Contacts, or a file in File Manager.
2. Tap Beam [type of item].
3. Tap the device to which you want to send the beam.
The item is beamed to the device you selected.
If the device that you want to beam to doesn’t appear in the list, make sure that it is
turned on, in discoverable mode, and within 10 meters (10 meters) of your device. Also,
make sure that your Bluetooth radio is turned on.
Pocket PC Phone User Manual
99
Receiving a Bluetooth Beam
1. Make sure that your device is configured to receive incoming beams and that Bluetooth
is in discoverable mode.
2. Make sure that your device is within 10 meters of the device beaming the information.
3. When prompted to receive an incoming beam, tap Yes.
The information is now stored on your device.
Using a Bluetooth Phone as a Modem
You can use a phone that has Bluetooth capabilities as a modem for your device. To do this,
you create a Bluetooth modem connection on your device and then send information to the
phone by using Bluetooth. The phone relays the information over the phone line and then
sends back to your device any information that you had requested over the connection.
Once you create a modem connection to the Bluetooth phone, you can reuse it whenever
you want to use the phone as a modem.
1. Make sure that the Bluetooth phone is turned on, that your device’s and the phone’s
Bluetooth radios are turned on, and that your device and the phone are within 10 meters
(10 meters) of one another.
2. If you have not already done so, create a Bluetooth phone connection by following
3. Tap Start menu > Settings > Connections tab.
4. Tap Connections > Add a new modem connection.
5. Enter a name for the connection.
6. In the Select a modem list, tap Bluetooth > Next.
7. Make sure that the phone is discoverable. Some phones may also need to be
pairable in order to accept a bonding request. For more information, see your phone
documentation.
100 Pocket PC Phone User Manual
8. If the phone appears in the My Connections list, skip to step 14. If not, tap New and follow
the remaining steps.
9. In the list, tap the phone and then Next.
10. In PIN, enter a PIN of between 1 and 16 characters, and tap Next.
11. Enter the same PIN on the phone.
12. If you want, in Name, edit the name of the phone.
13. Tap Finish.
14. In the My Connections list, tap the phone, and then Next.
15. Enter the phone number to dial for this connection and tap Next.
16. In User name, Password, and Domain, enter the logon information for this connection
and tap Finish.
17. Start using the program that uses the Bluetooth phone connection; for example Inbox to
send and receive e-mail, or Internet Explorer to browse the Web.
6.8 Wireless Modem
This utility will simulate your device as a wireless modem, and let your PC/Notebook be
connected to a wireless network. Before creating a new modem via selected connection
type, you still need to install the drivers on your PC/Notebook. For more details about
the drivers installation and the minimum requirements of your PC/Notebook, please refer
to Application CD.
1. Tap Start menu > Programs > then tap Wireless Modem.
2. Select a connection type.
3. Connect your device via infrared to a note-book or PC, and then tap Start.
Before you press the Start button, please make sure your device is with a GPRS SIM
card and you have connected this device to your PC/Notebook by IrDA connection and
disabled the Activesync.
Pocket PC Phone User Manual 101
Settings on your PC
Contact your ISP to get the APN (Access Point Name). Before you start using your
Wireless Modem with a IrDA connection, you need to create a new modem on your PC
first:
1. Click Start menu > Settings > Control Panel > Phone and Modem Options.
2. Add a new modem by selecting the Modem tab.
3. Enable the checkbox Don't detect my modem; I will select it from a list.
4. Select Standard Modem Types in the Manufacturers field, select Standard 33600 bps
Modem, then select Next.
5. Select your modem port and click Next.
6. When a Modem installation is finished! screen appears, click Finish to go back to the
Modem tab mentioned in Step 2. Now you can see a Standard 33600 bps Modem in the
modem list.
7. Highlight the modem you just created, click the Properties button, and select the Advanced
tab.
8. Enter the complete string in the Extra initialization commands: field: AT+CGDCONT=
1,"IP","APN","",0,0.
9. Remember to click the Change Default Preferences button after entering the required
string as mentioned above.
10. Click the General tab and set the Float control by selecting None from the drop-down
list. Keep pressing OK until the modem installation wizard exits.
A new standard modem is now set up successfully on your PC, but you still need to create
a new dial-up connection:
1. Click Start > Settings > Control Panel > Network and Dial-up Connections > Make
New Connection.
2. To continue, tap Next.
102 Pocket PC Phone User Manual
3. Select Dial-up to the Internet. Tap Next.
4. Enable the option I want to set up my Internet connection manually, or I want to
connect through a local area network (LAN) button, and Next.
5. Select I connect through a phone line and a modem option, and then Next.
6. Enable the Use area code and dialing rules checkbox and enter the telephone number
*99#, and then Next.
7. Enter the username and password you use to log on to your ISP, and then click Next.
8. Enter a name for this connection, and then Next.
9. Select No when the installation wizard asks you to set up an Internet mail account, and
then click Next.
10. After the installation is completed, click Finish.
Connecting via USB Port
As with the connection via IrDA, you need to check the following below before you start
using the Wireless Modem on your Pocket PC Phone via USB connection:
n A GPRS enabled SIM card is inserted in your Pocket PC Phone.
n Disable the ActiveSync com port connection of your PC.
n Disable the Infrared function by tapping the Start menu > Settings > the Connections
tab > Beam, and then uncheck Receive all incoming beams.
n Insert your Pocket PC Phone to your PC USB connection (using the USB sync cable or
cradle).
Before setting up an USB modem, you must verify that you have the two files, USBMDM
and USBModem_Dialer, on the Application CD. Insert the Application CD into the CDRom of your PC and perform the settings as follows:
1. Tap the Start menu > Programs > Wireless Modem.
Pocket PC Phone User Manual 103
2. Select the USB connection type from the drop-down list and insert the USB cable
adapter.
3. Tap the Start button on the Wireless Modem screen of your Pocket PC Phone.
4. A Found New Hardware message will pop up on your desktop PC.
5. Select the Display a list of the known drivers for this device so that I can choose a
specific driver option, and then click Next.
6. Select Modem from the Hardware types list, and then Next.
7. Click the Have Disk button, and then Next.
8. Select the recognized USB Modem in the Models list, and then Next. After the installation
is completed, select Finish.
9. After the installation, a new USB modem will be found in the Modem list by tapping Start
> Settings > Control Panel > Phone and Modem Options on your PC.
10. Double click the USBModem_Dialer file on the Application CD and set the GPRS settings
(enter the APN assigned by your ISP) in the blank text box and press Dial to start the
connection.
Connect via Bluetooth
Before starting to use your Pocket PC Phone as a Bluetooth modem, you must be sure that
your PC is a Bluetooth-enabled device. In addition, you still need to check the following:
n A GPRS enabled SIM card is inserted in your Pocket PC Phone.
n Disable the ActiveSync BT port connection of your PC.
n Disable the Infrared function by tapping the Start menu > Settings > the Connections
tab > Beam. Uncheck Receive all incoming beams.
1. To begin, select the Start menu > Programs > Wireless Modem.
2. Select the Bluetooth connection type from the drop-down list, and tap the Start button.
3. Open your Pocket PC Phone from the Bluetooth application installed on your PC.
104 Pocket PC Phone User Manual
The interface of the Bluetooth application installed on your PC will vary, depending on
the Bluetooth module embedded or attached in your PC when you purchased it. Follow
the installation instructions of the connected Bluetooth device's manual.
Chapter 7
Using Outlook
7.1 Calendar
7.2 Contacts
7.3 Tasks
7.4 Notes
106 Pocket PC Phone User Manual
7.1 Calendar
Use Calendar to schedule appointments, including meetings and other events. You can
check your appointments in one of several views (Day, Week, Month, and Agenda) and
set Calendar to remind you of appointments with a sound or other method. Appointments
for the day can be displayed on the Today screen.
If you use Outlook on your PC, you can synchronize appointments between your Pocket
PC Phone and PC. See Using ActiveSync in Chapter 4.
1
2
1. Tap to go back to view today's appointment.
2. Tap to display or edit the appointment details.
3. Tap to create a new appointment.
4. Tap to change the appointments in various
displayed views.
Create or change an
appointment:
1. To create an appointment, tap New. To select a
new date from a pop-up calendar, tap the display
date. To enter or select a new time, tap the display
time. Enter the appointment details, and when
finished, tap OK to return to the calendar.
3
4
2. If you are working in Day view, tap the time slot
for the new appointment and then New to have
the time automatically entered for you.
3. To change an appointment, tap it in the calendar, and then tap Edit. Change any appointment
detail by tapping it and entering the new information.
When entering a time, you can type military and abbreviated time forms, such as 2300
(becomes 11:00 PM), 913pm (becomes 9:13 PM), 911 (becomes 9:11 AM), and 9p (becomes
9:00 PM).
Pocket PC Phone User Manual 107
Tap the service
you want to use to
send the meeting
request.
Send a meeting request
You can use Calendar to set up meetings with users of Outlook or Pocket Outlook. The
meeting request will be created automatically and sent either when you synchronize Inbox
or when you connect to your E-mail server.
1. Create an appointment and enter the meeting information.
2. Tap Attendees (you will need to hide the input panel to see this box).
3. Select the meeting attendees from the list of E-mail addresses you’ve entered in Contacts.
Only those contacts with E-mail addresses will be displayed.
4. Select other desired options and then tap OK.
5. Messaging automatically creates a meeting request and sends it to the attendees the next
time you synchronize with your PC. Any textual notes entered in the Notes tab (excluding
writing or recordings) will also be sent.
If you are sending the meeting request through a connection to an ISP or the network, rather
than through synchronization with your PC, tap the Tools > Options > Appointments
tab. In Send meeting requests via, tap the service you want to use to send the meeting
request.
108 Pocket PC Phone User Manual
Use the summary screen
When you tap an appointment in Calendar, a summary screen is displayed. To change
the appointment, tap Edit.
Set a reminder for an appointment:
1. In the Calendar, tap the appointment, and then tap the upper portion of the summary screen
when editing the appointment.
2. Tap Reminder and select Remind me.
3. To change how many minutes before the appointment you are to be reminded, tap the
minutes displayed.
To automatically set a reminder for all new appointments, in the calendar, tap the Tools >
Options > the Appointments tab > Set reminders for new items.
Beam an appointment
To beam an appointment, in the calendar list, tap and hold the appointment. On the pop-up
menu, tap Beam Appointment. When using infrared (IR), align the IR ports between the
devices so that they are unobstructed and within close range of each other.
7.2 Contacts
Contacts maintains a list of your friends and colleagues so that you can easily find the
information you’re looking for, whether you’re at home or on the road. You can enter both
personal and business information.
If you use Outlook on your PC, you can synchronize contacts between your device and
PC. See ActiveSync in Chapter 4.
Pocket PC Phone User Manual 109
View contacts:
1. Select the category of contacts you want displayed in the list.
2. Tap and enter part of a name to quickly find it in the list.
3. Tap letters, such as h (home), w (work), or m (mobile) to the right of the contact to see
additional phone numbers and E-mail addresses.
4. Tap to display or edit the contact details.
5. Tap and hold to display a pop-up menu of available actions.
To change the way information appears in the list, tap Tools and then Options.
Create or change a contact:
1. Tap the Start menu > Programs > Contacts > New.
2. Using the input panel, enter a name and other contact information. You will need to scroll
down to see all available fields.
3. To assign the contact to a category, scroll to and tap Categories and select a category
from the list. In the contact list, you can display contacts by category.
4. To add notes, tap the Notes tab. You can enter text, draw, or create a recording.
5. To change a contact, tap it in the contact list, and then tap Edit. To cancel edits, tap Edit > Undo.
When finished, tap OK to return to the contact list.
If you enter a name with more than 2 words, the middle word will be recorded as a middle
name. If your contact has a double first or last name, tap the Name arrow and enter the
names in the proper box.
110 Pocket PC Phone User Manual
Find a contact:
n Tap the Start menu > Programs > Find, enter the contact name (first, last, or middle),
phone number, or address, select Contacts for the type, and then tap Go.
n From Contacts, start typing a contact name until you see it displayed on the screen. To
show all contacts again, tap the text box at the top of the screen and clear the text, or tap
the arrow icon to the right of the text box.
n Tap one of the sets of letters displayed at the top of the contact list. This takes you to the
contact names beginning with those letters.
n In the contact list, tap the category list (labeled All Contacts by default) and tap the category
to which you’ve assigned a contact. To show all contacts again, select All Contacts. To
view a contact not assigned to a category, select No Categories.
n To view the names of companies your contacts work for, in the contact list, tap View > By
Company. The number of contacts that work for that company will be displayed to the right
of the company name.
n Press and hold the top of the navigation pad until alphabetical letters appear on the screen in
large type. Then use the navigation pad to scroll through the alphabet and select a letter.
Beam a contact:
1. To beam a contact, in the contact list, tap and hold the contact. On the pop-up menu, tap
Beam Contact.
2. To beam multiple contacts, tap and drag to select the contacts. Then, tap Tools > Beam
Contacts.
When using infrared (IR), align the IR ports between the devices so that they are
unobstructed and within close range.
Pocket PC Phone User Manual 111
Change options:
1. In the contact list, tap Tools > Options.
2. To increase the available space for displaying contacts in the list, clear Show ABC tabs.
3. The area code and country/region for new contacts are automatically entered based on
the information in Country/Region settings.
Using the summary screen
When you tap a contact in the contact list, a summary screen is displayed. To change the
contact information, tap Edit.
7.3 Tasks
Use Tasks to keep track of things you need to do. A variety of task information can be
displayed on the Today screen. If you use Outlook on your PC, you can synchronize tasks
between your device and PC. See ActiveSync in Chapter 4.
Create or change a task:
1. To create a task with detailed information, such as start and due dates, tap the Start menu
> Programs > Tasks > New.
2. In the task list, you can display tasks by category.
3. To assign the task to a category, tap Categories and select a category from the list. To
create a new category, tap the Add/Delete tab, enter the category name, and then tap
Add. The new category is automatically selected in the Select tab.
4. To add notes, tap the Notes tab. You can enter text, draw, or create a recording. When
finished, tap OK to return to the task list.
5. To change a task, tap it in the task list, and then tap Edit. To quickly create a task, enter
text in the Tap here to add a new task box at the top of the screen. If you don't see this
box, tap Tools > Entry Bar.
112 Pocket PC Phone User Manual
Set a reminder for a task:
1. In the task list, tap the task, and then tap Edit.
2. Tap the Due field and set a due date if you have not already done so.
3. Tap the Reminder field and select Remind me. You will be reminded at 8:00 in the
morning on the due date.
4. To change the reminder date, tap the date displayed.
To be automatically reminded of new tasks with a due date, in the task list, tap Tools >
Options and select Set reminders for new items.
To choose how you are reminded, for example by a sound, tap the Start menu > Settings
> the Personal tab > Sounds & Notifications.
Using the summary screen
When you tap a task in the task list, a summary screen is displayed. To change the task,
tap Edit.
Beam a task
To beam a task, in the task list, tap and hold the task. On the pop-up menu, tap Beam
Task.
7.4 Notes
Notes help you quickly capture ideas, notes, and thoughts. You can create a note using
written and typed text, drawings, and recordings. You can also share your notes with
others through E-mail, infrared, and synchronization with your PC. Please see Chapter 4
for more information.
To create documents with advanced formatting or templates, such as bulleted lists and
tabs, use word processing software developed for your device, such as Pocket Word.
Pocket PC Phone User Manual 113
Create a note:
1. Tap the Start menu > Prgrams > Notes > New.
2. Create your note by writing, drawing, typing, and recording, see Entering Information in
Chapter 2 for more information about using the input panel, writing and drawing on the
screen, and creating recordings.
You can insert the date in a note. First, deselect
and make sure that no drawings are
selected. Next, tap and hold anywhere on the note and then tap Insert Date.
Send a note by E-mail:
1. If you haven’t already set up Messaging to send and receive messages, please do so now.
See Chapter 8.
2. In the note list, tap and hold the note or recording. To select multiple notes or recordings,
tap and drag. Then, tap and hold the selected items.
3. On the pop-up menu, tap Send via E-mail. A new message is created with the item
attached.
Beam a note
To beam a note, in the note list, tap and hold the note. On the pop-up menu, tap Beam
File.
Change options:
1. In the note list, tap Tools > Options.
2. From the Default template list, you can select a pre-designed template to use with all new
notes.
2. If you store most of your notes and recordings on a storage card, in Save to, tap Storage
card to have new items automatically stored on your storage card.
114 Pocket PC Phone User Manual
Chapter 8
Messaging Features
8.1 E-Mail and Text Messages
8.2 MSN Messenger
8.3 MMS Messages
116 Pocket PC Phone User Manual
8.1 E-Mail and Text Messages
You can receive E-mail and text messages in Messaging. E-mail messages are sent by
using an address you receive from your Internet service provider (ISP), an E-mail service
provider, or your employer. Text messages are sent and received through your phone
service provider by using a phone number as the message address.
You can also send and receive E-mail by synchronizing with your PC, or by connecting to a
Post Office Protocol 3 (POP3) or Internet Message Access Protocol 4 (IMAP4) mail server.
You need to set up an E-mail account for each method that you use except for an Outlook
E-mail account, which is set up by default. The Outlook E-mail account on your Pocket
PC Phone is used to store messages that you send and receive through synchronization
with a PC. Account names appear when you open the folder list, which is located on the
left, under the navigation bar, in the message list view.
How you download copies of messages depends on how you are receiving messages:
n If you receive E-mail messages through a remote E-mail server, follow the instruction as
described on the next page, under "Downloading messages from a server."
n If you receive E-mail messages through ActiveSync, begin synchronization. For more
information, please refer to Chapter 4.
n Text messages are automatically received when your phone is turned on. Otherwise,
messages are held by your service provider until the next time your phone is turned on.
With synchronization, messages are synchronized between the Pocket PC Phone Inbox
folder for the Outlook E-mail account and the PC Inbox by using ActiveSync and Microsoft
Exchange or Outlook. For more information, see Chapter 4.
Pocket PC Phone User Manual 117
Setting up an account:
Open Messaging on your Pocket PC Phone by tapping the Start menu > Messaging.
Select Outlook E-mail in Accounts. Tap Accounts, New Account to set up an account.
Accounts > New Account. The E-mail Setup wizard will prompt you to fill in the necessary
information to complete the setup.
1. Fill in your E-mail address, then tap Next.
2. The Auto configuration will attempt to connect your Pocket PC Phone to your E-mail server
and automatically download the necessary connection settings. If Auto configuration is
unsuccessful, contact your ISP or network administrator.
3. Enter Your name, User name and Password, then tap Next. If you check the Save
password box, your device will not ask for your password the next time you log in to an
E-mail account. However, other people can access your account if you lose the device.
4. Select the appropriate Account type that your E-mail provider supports (POP3 or IMAP4).
Enter a Name for your E-mail account, then tap Next.
5. Enter your E-mail provider’s server name information for Incoming mail and Outgoing
mail, then tap Finish.
When finished, tap Accounts. Your new E-mail account will be displayed under this menu.
You can start connecting to your E-mail server at this point.
You can set up several E-mail accounts, including your Outlook E-mail account. A Text
Messages account and an MMS account is already pre-configured in Messaging.
Changing options for an account:
1. Tap Accounts > Accounts.....
2. Tap the name of the account, and follow the instructions on the screen.
118 Pocket PC Phone User Manual
Deleting an account:
1. Tap Accounts > Accounts....
2. Tap and hold the name of the account > and then tap Delete.
You cannot delete the text messages and MMS account.
Downloading messages from a server
In Messaging, tap Accounts > Connect to open a connection to the Internet or your
corporate network, depending on the account. For more information, see Chapter 6.
1. Tap Accounts and ensure that the account you want to use is selected (marked by a
bullet).
2. Tap Connect. The messages on your device and E-mail server are synchronized. New
messages are downloaded to your Pocket PC Phone Inbox folder, messages in your Pocket
PC Phone Outbox folder are sent, and messages that have been deleted from the server
are removed from your Pocket PC Phone Inbox. Tap a message in the message list to
open it.
3. If you read a message and decide that you need the full copy, tap Edit > Mark for Download
while in the message window. If you are in the message list, tap and hold the message, and
then tap Mark for Download. This will also download message attachments if you selected
those options when you set up the E-mail account. You can also choose to download full
copies of messages by default.
4. When finished, tap Accounts > Disconnect.
Receiving attachments
An attachment sent with an E-mail message or downloaded from the server appears as
an icon at the bottom of the message in its own window pane. Tapping the attachment
icon opens the attachment if it has been fully downloaded. You can mark an attachment
for downloading (IMAP4 account only) the next time you connect.
Pocket PC Phone User Manual 119
Through synchronization:
1. Start ActiveSync on your PC.
2. Click File > Mobile Device > and then select your mobile device.
3. Click Tools > and then click Options.
4. Select the message account > Settings, and then select Include File Attachments.
Through a remote IMAP4 E-mail server:
1. From Messaging, tap Accounts > Accounts... > IMAP4.
2. Tap Next until you reach Server Information > and then tap Options.
3. Tap Next twice > Get full copy of messages and When getting full copy get
attachments.
Embedded images and objects cannot be received as attachments. An embedded message
can be viewed as an attachment when using IMAP4 to receive E-mail. However, this feature
does not work if TNEF (Transport Neutral Encapsulated Format) is enabled so that you
can receive meeting requests.
Composing and sending a message:
Text Messages (SMS) cannot be used to send E-mail messages. You can tap the double
arrows next to the Subj. field to show the complete header. From the Account list, select
an E-mail account.
If you are sending a text message (SMS) and want to know if it was received, before sending
the message, tap Tools > Options > Request message delivery notification.
You can also send a text message from the Phone Dialer Screen by tapping Tools >
Send Text Message. A new message screen will appear in Messaging.
120 Pocket PC Phone User Manual
1. In the message list, tap Accounts and select Outlook E-Mail, Text Messages (SMS), or
the desired E-mail account.
2. Tap New.
3. Enter the E-mail address or text message address of one or more recipients, separating
them with a semicolon. To access addresses and phone numbers from Contacts, tap To.
or tap the Address Book button.
4. Enter your message. To quickly add common messages, tap My Text and tap a desired
message.
5. To check spelling, tap Tools > Spell Check.
6. Tap Send. If you are working offline, the message is moved to the Outbox folder and will
be sent the next time you connect.
Managing Messages and Folders
Each E-mail account and text message account has its own folder hierarchy with five
default folders: Inbox, Outbox, Deleted Items, Drafts, and Sent Items. The messages
you receive and send through the mail account are stored in these folders. You can also
create additional folders within each hierarchy. The behavior of the folders you create
depends on whether you are using an Outlook E-Mail, Text Messages, POP3, MMS,
or IMAP4 account.
If you use an Outlook E-Mail account, E-mail messages in the Inbox folder in Outlook
E-Mail will automatically be synchronized with your device. You can elect to synchronize
additional folders by designating them for ActiveSync. The folders you create and the
messages you move will then be mirrored on the server.
If you use a Text Messages account, messages are stored in the Inbox folder.
If you use a POP3 account and you move E-mail messages to a folder you created, the
link is broken between the messages on the device and their copies on the mail server.
The next time you connect, the mail server will see that the messages are missing from
Pocket PC Phone User Manual 121
the device Inbox folder and delete them from the server. This prevents you from having
duplicate copies of a message, but it also means that you will no longer have access to
messages that you move to folders created from anywhere except the device.
If you use an IMAP4 account, the folders you create and the E-mail messages you move
are mirrored on the server. Therefore, messages are available to you anytime you connect
to your mail server, whether it is from your device or PC. This synchronization of folders
occurs whenever you connect to your mail server, create new folders, or rename/delete
folders when connected.
For all accounts except Outlook E-Mail, you can access folder options by tapping Tools
> Manage Folders.
8.2 MSN Messenger
MSN Messenger features include:
n Seeing who is online.
n Sending and receiving instant messages.
n Having instant message conversations with groups of contacts.
n Notifying contacts of your on-line status.
n Blocking contacts from seeing your status or sending you messages.
To use MSN Messenger, you need a Microsoft Passport account, or a Microsoft
Exchange E-mail account that your employer provides. Once you have one of these
accounts, you will need to:
n Set up an account on MSN Messenger.
n Sign in to MSN Messenger.
122 Pocket PC Phone User Manual
Setting up an account
Before you can use MSN Messenger, you must set up the instant messaging account(s)
to use. For MSN Messenger Service, you must have a Microsoft Passport or Hotmail
account. For Exchange Instant Messaging, you must have an Exchange account.
1. To use MSN Messenger Service, set up a connection to the Internet; to use Exchange
Instant Messaging, set up a connection to your corporate network.
2. Tap the Start menu > Program > MSN Messenger.
3. In MSN Messenger, tap Tools > Options > the Accounts tab.
4. Select Enable MSN Messenger Service and/or Enable Exchange Instant Messaging.
5. Enter your sign-in name and password for the selected account(s). Your sign-in name is
usually in the form: username@domain.com.
6. If you selected both accounts, tap Settings, and select which account to sign in to first.
n To set up a Microsoft Passport account, go to http://www.passport.com.
n To set up a Hotmail account, go to http://www.hotmail.com.
n To set up an Exchange account, see your network administrator.
Signing In and Signing Out
1. To sign in, tap anywhere on the screen. Follow the directions on the screen.
2. To sign out, tap Tools > Sign out.
To sign in as your device is connected to the Internet, tap Tools > Options > the General
tab > and select the Run this program upon connection box.
Signing in to an Exchange account may take several minutes depending upon your
connection speed. Reducing the number of Exchange contacts will decrease your signin time.
Pocket PC Phone User Manual 123
8.3 MMS Messages
With the Pocket PC Phone, you can create and share your own MMS messages, complete
with photos, videos, text, and audio to your friends and family. You can even use the
Pocket PC Phone’s camera to snap photos and immediately send them by composing
an MMS message.
Launching the MMS composer screen
MMS is incorporated into the Pocket PC Phone’s Messaging function. You can access
MMS directly by selecting the Start menu > Messaging > Accounts > MMS. Your device
also allows you several ways to launch the MMS composer screen:
n From Album: Select any picture in Album, tap on Tools > Send via MMS. At this point you
will be directed to the MMS composer screen in Messaging.
n From Camera (Optional): Capture a picture or a video clip. A Review mode pop-up menu
will let you select from the four icons after you have captured an image or video clip, one
of which will be Send via MMS.
Creating an MMS Message
MMS messages are created by combing various slides. Each slide can consist of a photo,
an audio or video clip, audio, or text. To begin select the Start menu > Messaging >
Accounts > MMS. In the MMS Inbox, tap New. You may not automatically be taken to
a blank message, but to a page that displays pre-made templates, choose the template
you want. If you would prefer to create a blank message next time, check the “Always
choose custom” box.
124 Pocket PC Phone User Manual
Message Boxes
To view message folders:
When the program starts, it will take you to your message boxes. Use the pull-down to select
the one you wish to view.
To view message options:
Within each message box, you can tap and hold on an individual message to see various
options.
Options
Explanations
New
Creates a new message.
Delete
Removes the message.
Move...
Move the selected message to another folder.
Reply
Lets you respond to the message by sending one of your
own.
Reply All
Responds to everyone included in the initial message.
Forward
Sends the message to someone else.
Send/Receive
Send or receive the selected message
Mark as Unread
Makes the message appear as if it is a newly received
message.
Message Info
Displays various message information, such as the sender, the
subject, the date and time it was sent, and the size.
Pocket PC Phone User Manual 125
Creating a message
Messages are created by combining various slides. Each slide can consist of a photo or
video, audio, and text. A quick run-down of the Create screen is illustrated as below:
1
2
6
3
4
5
1. Enter the recipient’s phone number or email directly.
Or, tap on the To button to select either - Phone to see your phone
book or Email to see your email address book.
2. Enter a subject for your message.
3. Tap here to choose a photo or video.
4. Tap here to input a text message.
5. Tap here to include an audio clip.
6. When you’re ready, tap Send. Otherwise, tap Cancel.
126 Pocket PC Phone User Manual
To add a picture or video clip:
You can add either a still image or a video clip to each individual slide. After you’ve tapped
the area to add a photo or video, you’ll be allowed to select exactly what you want to
include.
1
3
2
5
4
1. This pull-down lets you select a specific location that contains photos/videos.
2. Choose either Photos or Videos from this pull-down. You can only add either
a single photo or video clip to each individual slide.
3. Tap the specific photo or video clip that you want to add.
4. Tap the specific photo or video clip that you want to add, then tap
select.
to
5. To take a new picture or video clip press the Camera icon The picture or video
clip will be automatically inserted.
Tap and hold on a file to see the File Info and Delete options. File Info displays the file
name, resolution, date, and size of a photo. When viewing video file information, the
duration of the video is also listed. Delete deletes the file.
Pocket PC Phone User Manual 127
To add text:
You can add text to any slide. You can either enter in new text with the keyboard, or use
Canned Text. Canned Text are previously saved words or phrases:
1. Tap the Insert text here box, then enter the text you want to send.
2. To insert Canned Text, tap the small icon on the right upper corner of the
Insert text here box, and then select a phrase from the list and tap
to select.
3. To add new, edit or delete existing canned text, tap and hold on the
canned text screen.
To add audio clips:
Single audio clips can be added to each slide. You can either include an existing sound
file, or record a new one.
1. From the drop-down menu, select a location that contains audio files.
2. Tap the file you'd like to use.
3. Preview the audio files by tapping on them. Use the toolbar below to Stop and
Play the file.
4. To insert the clip tap
Otherwise, tap
.
5. To record a new audio clip, tap the Record
icon, then tap
and
to finish. The clip will be automatically inserted.
to start recording
128 Pocket PC Phone User Manual
Menu commands
The following commands are available along the bottom of the screen:
1. Edit
Insert Slide
Adds a new, blank slide to your current message.
New From
Template..
Lets you create a new message using a pre-made
template.
Save As Template
Lets you save the current message as a template for
later use.
Delete Slide
Removes the current slide from your message.
Organize Slides...
Lets you arrange the slide order and display time for each
slide.
Add vCard
Attaches a vCard of your choice to the message.
Add vCalendar
Attaches an appointment of your choice to the message.
Capture Picture...
Lets you take a new picture (optional).
Capture Video...
Lets you capture a new video (optional).
Cancel
Backs out of the message creation and returns you to
your message box.
2. Options
Text
Choose between “Top” and “Bottom.” This determines where
your included text will appear in the message.
n Uncheck the “Send the message now” box to manually set
the date and time that you would like the message sent.
Send
Options...
n From the “Expiration” pull-down, select how long you’d like
the message to be stored on the server. The server will stop
attempting to deliver the message after the set time expires.
n Set the message priority from the Priority pull-down.Check the
Delivery Report box to be notified when the recipient downloads
your message.
Pocket PC Phone User Manual 129
Viewing a message
You have several options when viewing a message that you receive:
1. Use the playback controls (Play/Pause, Stop) to view the message. You can
pause it anytime during playback.
2. Tap Objects to see a list of each file. If you want to save a particular file, tap it,
then choose Save from the Tools menu.
3. You can also view the slides manually. Use the navigation buttons to scroll
through the message.
MMS Settings
To view and edit your MMS Messages, tap on the Tools menu which is located at the
bottom of the screen, and then select MMS Settings.
In the Preferences tab:
n Connect Via: Select your type of network connection from the pull-down.
n Retrieve Messages Immediately: Typically, you receive a notification whenever a new
message is available. Checking this box downloads new messages automatically. You can
also choose to download messages while roaming.
n Save Sent Messages: Check this option to save a copy of messages that you send.
n Attempts Before Giving Up: This value sets the number of times the program will attempt
to send your message before stopping.
n Photo Resolution: Choose the resolution for images that you send. You may want to
decrease below the original resolution to help the send/receive time.
In the Servers tab, it lists all available servers that you can use, or alternatively, you can
set up a new one.
In the About tab, it lists various program information, such as the End User Licence
Agreement,etc.
130 Pocket PC Phone User Manual
Chapter 9
Applications
9.1 Pocket Word
9.2 Pocket Excel
9.3 Windows Media Player
9.4 Pictures
9.5 ClearVue PPT
9.6 ClearVue PDF
9.7 MIDlet Manager
132 Pocket PC Phone User Manual
9.1 Pocket Word
You can create and edit documents and templates in Pocket Word just as you would do in
Word on your PC. Pocket Word documents can be saved as .psw, .doc, .rtf, or .txt files.
You can enter information in a document by typing, writing, drawing, or recording. After
you close a document and name it, the document is automatically placed in the Pocket
Word document list.
Synchronizing Pocket Word documents
Pocket Word documents can be synchronized with Word documents on your PC. To
synchronize files, select the Files type for synchronization in ActiveSync Options settings
on your PC. When you select Files, a \My Documents folder is created on your PC’s
desktop. Place all the files you want to synchronize with the device in this folder. Please
note that password-protected files cannot be synchronized.
All Pocket Word files that are stored in \My Documents and its subfolders are synchronized
with the PC. ActiveSync will convert the documents during synchronization. When you
delete a file on your PC or your device, the file will be deleted in the other location the
next time you synchronize. For more information on synchronization, or file conversion,
see ActiveSync Help on the PC.
Document conversion
The Word documents (.doc) and templates (.dot), created in Word 6.0 or later on the PC,
are converted to Pocket Word documents (.psw) and templates (.psw). The conversion
takes place during the following:
n During file synchronization.
n When you copy a Word file from the PC to your Pocket PC Phone.
n When you open an E-mail message with an attached Word file on your device.
Pocket PC Phone User Manual 133
Pocket Word documents are converted to Word documents when they are synchronized
or copied back to the PC. During the conversion from Word to Pocket Word, most simple
text and paragraph formatting will be retained and displayed, but some formatting attributes
could be changed or lost.
9.2 Pocket Excel
You can create and edit workbooks and templates in Pocket Excel just as you would do
in Excel on your PC. Pocket Excel workbooks are usually saved as .pxl files, but you
can also save them in the .xls format. When you close a workbook, it is automatically
named and placed in the Pocket Excel workbook list. You can attach a password to a
workbook to ensure privacy.
Synchronizing Pocket Excel workbooks
Pocket Excel workbooks can be synchronized with Excel workbooks on your PC. To
synchronize files, select the Files type for synchronization in ActiveSync Options settings
on your PC. When you select Files, a \My Documents folder is created on your PC’s
desktop. Place all the files you want to synchronize with the device in this folder. Passwordprotected files cannot be synchronized.
All Pocket Excel files that are stored in \My Documents and its subfolders are synchronized
with the PC. ActiveSync converts documents during synchronization.
When you delete a file on your PC or your device, the file will be deleted in the other
location the next time you synchronize.
For more information on synchronization or file conversion, see ActiveSync Help on the
PC.
134 Pocket PC Phone User Manual
Workbook conversion
The Excel files (.xls) and templates (.xlt), created in Excel version 5.0/95 or later on the
PC, are converted to Pocket Excel workbook (.pxl) or template (.pxt) files. The conversion
takes place during the following:
n During file synchronization.
n When you copy an Excel file to your device from the PC.
n When you open an E-mail message with an Excel file as an attachment.
Pocket Excel workbooks are converted to Excel workbooks when they are synchronized
or copied back to the PC.
During the conversion from Excel to Pocket Excel, most simple text and paragraph
formatting will be retained and displayed, but some formatting attributes could be changed
or lost.
9.3 Windows Media Player
Use Windows Media Player to play audio and video files that are stored on your Pocket
PC Phone, a network, or the Internet.
You can play files in either Windows Media or MP3 format (this includes files with the
extensions .asf, .wma, .wmv, and .mp3.) To find contents in the Windows Media Format
for your Pocket PC Phone, please go to http://www.windowsmedia.com.
To turn on Windows Media Player on your Pocket PC Phone, tap the Start menu >
Programs > Windows Media.
Pocket PC Phone User Manual 135
About the playlist
A playlist is a list of digital media files that play in a specified order. By using playlists, you
can group audio and video files together for convenient playback. For example, you can
create a playlist of your favorite songs by a particular artist or a playlist of work-related
video clips.
For more information about creating and editing a playlist on your Pocket PC Phone, select
Help from the Start menu.
Play a file on a network:
To play streaming media, your device must be connected to a network. See the remote
connection settings in Chapter 6 for more information.
1. In Player Screen, tap Menu > Open URL.
2. Enter a URL in the Location to Open: field.
9.4 Pictures
Pictures collects, organizes and sorts .jpg picture files on your device. With Pictures,
you can download images to your PC, use ActiveSync to copy the files to your Pocket PC
Phone, and view the images as a slide show.
Pictures can also be stored and transferred to your device from a MMC, SD, or any storage form factor supported by your digital camera. Insert a card into the memory card slot
and then copy or drag the pictures from your PC to the My Documents directory on the
memory card. (If the memory card does not have a My Documents directory you must
create one first).
136 Pocket PC Phone User Manual
Transferring pictures
Pictures stored on your PC can be synchronized with Pictures on your device. Picture
synchronization is not automatically selected in ActiveSync; you need to tap the sync option
Files in ActiveSync on your desktop PC to activate this function.
Finding and listing pictures:
1. Tap the Start menu > Programs > Pictures.
2. Tap My Pictures and select a folder from the drop-down menu.
Viewing pictures:
Tap to select a folder from the
drop-down menu
1
1. In Pictures, tap
2
3
to view pictures as a slide show.
2. Tap
to view pictures stored in your My Pictures folder.
3. Tap
to view pictures stored on a storage card.
n During the Slide Show, tap anywhere on the screen to display the Slide show toolbar, which you
can use to pause the Slide Show and rotate the view.
n Press the Left/Right controls to move forward or backward through the slides.
Pocket PC Phone User Manual 137
Sorting pictures:
1. Tap the Start menu > Programs > Pictures.
2. Tap to select a sorting option such as Name, Date, Size, and Type from the drop-down
menu.
Deleting an image
Hold the stylus firmly on the file name of the picture you want to delete. Select Delete
from the pop-up menu.
Edit pictures
You can rotate, crop, zoom and adjust the brightness and color contrast of your .jpg
pictures. Tap the desired picture, then:
n Tap
to rotate a picture 90 degrees counter-clockwise.
n Tap
to crop a picture by dragging and selecting the crop area. Tap outside of the box
to stop cropping.
n Tap
to display the Zoom panel, from which you can zoom in or out of a picture, or return
a picture to full-screen size.
n Tap Edit > Brightness and Contrast to adjust the brightness and contrast of a picture.
n Tap Edit > Undo to undo an edit, or Redo to redo an edit.
138 Pocket PC Phone User Manual
Set pictures as background
You can use one of your own .jpg pictures as the background on the Today screen, and
specify how you want it displayed on the screen, such as adjusting the transparency
level.
1. In Pictures, tap the picture you want to set as the background.
2. Tap Tools > Set as Today Wallpaper.
The default setting for the transparency level of the background picture is 65%. This can be
adjusted in the Set as Today Wallpaper screen.
Customizing pictures
You can launch Pictures automatically when a digital camera storage card is inserted. You
can also set the length of the time delay between slides for a slide show.
To select launch automatically:
1. Tap the Start menu > Programs > Pictures.
2. Tap Tools > Options > the General tab.
3. Check the Detect digital camera storage cards box.
To select the time delay between slides:
1. Tap the Start menu > Programs > Pictures.
2. Tap Tools > Options > the Slide Show tab.
3. Select a number of seconds, then tap OK.
Pocket PC Phone User Manual 139
9.5 ClearVue PPT
ClearVue PPT (Presentation) displays presentations created in PowerPoint 97,
PowerPoint 2000 and PowerPoint 2002. ClearVue Presentation allows you to view
your presentation as it was created. The program also allows you to create a Custom
Slide List. In this list, you can select which slides to include in the presentation and you
can change the order of the slides presented.
ClearVue Presentation displays the first slide in the presentation in either the Normal View
or the Slide Sorter View. From the current view, you can Change the View, Set Up a Show,
View Notes attached to your presentation, Zoom in on a slide, or View your show.
Conversion settings
Before viewing PowerPoint presentations, you must change your default file conversion
settings so that files transferred from your PC to your handheld are not changed.
1. Launch ActiveSync on your desktop and go to Tools > Options.
2. On the Options page, choose the Rules tab > Conversion Settings.
3. Choose the Desktop to Device tab, highlight PowerPoint Presentation from the list and
click Edit.
4. Choose No conversion (*.ppt) from the drop down and click OK three times until you are
back on the main ActiveSync screen.
Any PowerPoint files you transfer to your handheld will now be preserved in their original
format for viewing.
140 Pocket PC Phone User Manual
View a presentation
To open a PPT presentation file:
1. Launch ClearVue Presentation by tapping the Start menu > Programs > ClearVue
PPT.
2. Tap File > and select Open to view a list of .ppt files on your Pocket PC Phone > Tap the
file you want to view.
3. Tap Slide Show to view the slides from the View menu or by using the Icon on the
toolbar.
The Slide Viewer opens with the presentation in the Normal View or the Slide Sorter
View. You can change the view by selecting an alternate View from the View menu or by
using one of the ToolBar icons. If the presentation was received as an E-mail attachment,
you can also just tap on it to open.
Normal Viewer
The Normal View has the Slide List and the Image Window. You can also view Notes in
the Normal View. On your Pocket PC Phone, Notes that are attached to your presentation
can be viewed by selecting Notes from the View menu.
The Slide List window allows you to do the following:
n Choose the image shown in the Image window by selecting the slide in the list.
n Select which slides will show in your presentation by checking or unchecking the slide
checkbox in the slide list.
n Move a slide up or down by using the Move slide up or Move slide down ToolBar icon.
The Image Window allows you to do the following:
n Scroll through the slides using the scroll bars.
n Zoom in on a slide for a closer view by double clicking the Image Window.
Pocket PC Phone User Manual 141
n Click on the Watermark in the lower left corner of the image to bring up a context menu.
From this menu you can:
n Go to any slide you want to view.
n Zoom in or out for viewing.
n Select Rotation to rotate the slide to Portrait or Landscape.
n Select Close to go back to the Image Window.
The Slide Sorter
The Slide Sorter shows slide thumbnails of the currently selected presentation. From this
window, you can do the following:
n Sort the slides by selecting the Move slide up or Move slide down. Or, use the stylus to
drag and drop the slide to the desired location.
n Select which slides to include in your presentation by selecting an image. Then, selecting
or deselecting Select Slide from the Setup menu.
n Zoom in on a slide for a closer view by double clicking on the slide.
Set up a slide show
The Set Up Show dialog can be opened from the Setup menu. From the Set Up Show
dialog, you can do the following:
n The Slide List allows you to Select which slides will show in your presentation. You can
do this by checking or unchecking the slide checkbox.
n You can also set the Advance Slide for Manual, Use timings, or Automatic.
The Manually button will ignore all PowerPoint timings, allowing you to control the time
between animations and transitions.
The Use timings, if present button will display the show just as it does in PowerPoint.
The Automatically advance after button will allow the show to run on its own. When the
Automatic button is selected, you can set the Timing between slide transitions, and Loop
the show if desired.
142 Pocket PC Phone User Manual
Navigating a presentation
While a slide show is running, you can move to another slide by doing one of the
following:
n Click on the presentation screen to advance one slide forward, but this is disabled when
using a Pen or Pointer.
n While a slide show is running, click on the arrow watermark in the lower left corner of the
screen to bring up a Context menu. From this menu, you can view the Next slide action,
the Previous slide action, or select a slide from the Go to... drop down list. You can also
use a Pen to mark on a slide or a Pointer for clarity. If you want to stop the presentation
show, select End Show.
n Tap on the Right and Down buttons move to the next slide, and the Left and Up buttons
move to the previous slide.
9.6 ClearVue PDF
ClearVue PDF displays Portable Document Format files. These files usually have a .pdf
extension.
To open a PDF file:
1. Launch ClearVue PDF by tapping the Start menu > Programs > ClearVue PDF.
2. Tap File > Open to view a list of .pdf files on your Pocket PC Phone > Tap the file you want
to view.
Moving around in a document
When a document is larger than one screen, scroll bars enable you to move around. You
can navigate around a .PDF file in the following ways:
n Tap the up/down and right/left arrows to move one line to the desired direction. You can
also use the navigation pad to move around the screen.
Pocket PC Phone User Manual 143
n Click and hold the space between the arrow and the scroll bar to move one screen to the
desired position.
n Use the left, right, up and down arrow keys on the soft keyboard to move to the desired
position.
n You can also tap and hold and then drag the screen to move around the document to the
desired position.
The Zoom feature
The Zoom feature allows you to enlarge or reduce the document content on display.
Zoom is available from the View menu.
To get a different view of a document, select from the preset Zoom settings, or choose
a Custom Zoom.
9.7 MIDlet Manager
Your Pocket PC Phone supports Java 2 Edition, J2ME. The MIDlet Manager allows you
to download Java applications such as games and tools specifically designed for mobile
devices. You will find that some Java applications and games may have already been
installed on your device. The Java MIDlet Manager gives you the flexibility of installing
and managing additional J2ME applications from the Internet.
Installing MIDlets directly from the Internet
You can install MIDlets/MIDlet suites directly from the Internet using Internet Explorer in
conjunction with the MIDlet Manager.
1. Connect to the Internet and locate a MIDlets/MIDlet suite you wish to download (this is
normally a .jad and a .jar file).
2. Select the MIDlets/MIDlet suite and download it.
3. You will be asked to confirm before the download begins.
144 Pocket PC Phone User Manual
4. A progress screen is displayed while the files are being downloaded. You may cancel the
download at any time.
Once your download is completed, the MIDlet Manager will automatically start and prompt
you to install your new MIDlets/MIDlet suite. You must confirm that you want to proceed
and the installation of your MIDlets/MIDlet suite is completed. Alternatively, you can cancel
the installation at any time.
Installing MIDlets from a PC
You can install MIDlets/MIDlet suite onto your Pocket PC Phone from your PC using the
USB sync cable, the optional cradle, infrared or Bluetooth. MIDlets transferred to your
Pocket PC Phone using infrared, Bluetooth, or as E-mail attachments are automatically
saved in the My Documents directory.
To install MIDlets via a physical connection (such as USB sync cable or cradle) use Windows Explorer to copy your MIDlet file(s) from your PC to any of the following temporary
directories, from where they can be installed by the MIDlet Manager.
n Device memory: Mobile Device\My Pocket PC Phone\My Documents\My MIDlets
n Storage card: Mobile Device\My Pocket PC Phone\Storage Card\
If the folder My MIDlets not exist in My Documents, you need to create one with exactly
the same folder name. The folder Storage Card will automatically appear once you insert
the SD card to your Pocket PC Phone.
Once the file(s) have been copied to your Pocket PC Phone or to your storage card, you
must install the MIDlet/MIDlets suite:
1. Tap the Start menu > Programs > MIDlet Manager > Menu > Install.
2. The Install screen will open, containing a list of all available MIDlets/MIDlet suites.
3. Select one and choose Install from the pop-up menu. You will be prompted to confirm your
choice.
Pocket PC Phone User Manual 145
Optionally, you can remove the MIDlet files from the temporary folder you used by tapping
Delete from the pop-up menu.
Running MIDlets
The MIDlet Manager enables you to run MIDlets/MIDlet on your Pocket PC Phone. You
can leave MIDlets running in the background while you perform other tasks on your Pocket
PC Phone. You can have multiple MIDlets running at the same time, depending on the
total amount of memory available on your Pocket PC Phone.
1. Tap the Start menu > Programs > MIDlet Manager.
2. Select a suite and tap to run the MIDlet. The MIDlets/MIDlet suite you selected will open
within the MIDlet Manager window.
You can tap Show > Running to display the MIDlets/MIDlet suite currently running on
your Pocket PC Phone. You can also return to a running MIDlet by selecting it from this
screen.
You can also tap the Show > Recent option to display up to the 9 most recently used
MIDlets.
Stopping MIDlets
Some MIDlets have an exit or stop command within their menu structure, which are
determined by the specific software developer.
Stopping a MIDlets/MIDlet suite:
To stop an individual MIDlet, navigate to the Running MIDlets screen:
1. Tap the Start menu > Programs > MIDlet Manager.
146 Pocket PC Phone User Manual
2. Tap Show > Running.
3. Tap and hold the MIDlet you want to stop and then select Stop from the pop up menu.
Stopping all MIDlets
To stop all the MIDlets running on your Pocket PC Phone, navigate to the Running
MIDlets screen:
1. Tap the Start menu > Programs > MIDlet Manager.
2. Tap Show > Running.
3. Tap Menu > Stop All.
Once your MIDlets have been stopped, you will be returned to the MIDlet Manager
window.
Managing your MIDlets/MIDlet suites
You can organize your MIDlets into groups and define custom groups. You can manage
the default settings for MIDlets, including security settings.
Customizing your display settings:
1. Tap Sort By menu on the up-right corner of the MIDlet Manager screen to personalize
your display options.
2. You can choose your MIDlets/MIDlet suite to be sorted by Name (A to Z) or by Size (small
to large).
Changing the display name of your MIDlets
You can change the displayed name of any MIDlet on your Pocket PC Phone. However,
you cannot change the names of MIDlet suites.
1. Tap and hold the MIDlet you wish to change the name of and the then select Rename from
the pop-up menu.
Pocket PC Phone User Manual 147
2. Enter the new name for your MIDlet in the dialogue box and press OK to confirm, or Cancel
to abort.
Un-installing MIDlets/MIDlet suites
You can remove MIDlets/MIDlet suites from your Pocket PC Phone’s memory. To do this,
ensure that the MIDlets/MIDlet suite is not running.
1. Select the MIDlets/MIDlet suite in the MIDlet Manager window and choose Un-install.
2. You will be asked to confirm your decision by selecting the OK option. The MIDlet is then
erased from your device's memory.
You cannot un-install a single MIDlet from a MIDlet suite. You must un-install the complete
MIDlet suite.
To assign a group to a MIDlets/MIDlet suite
1. Tap and hold on a MIDlet you wish and choose Group from the pop up menu in the MIDlet
Manager window.
2. The MIDlet Manager window contains a drop down box with a list of group names. Choose
one of these and tap OK.
You can adapt existing groups to meet your needs. Once a MIDlet has been assigned to a
group, that group’s name will appear on the Show menu, and you can choose any group
and view the MIDlets in it.
System Info
You can see the information about the currently used space of the MIDlets/MIDlet suite you
have selected by tapping Menu > System Info. If the manufacturer has limited the total
storage space for MIDlets, the limit and the amount currently available is also shown.
148 Pocket PC Phone User Manual
Network Type
Tapping Menu > Choose Network Type enables you to choose your connection from
the available list.
MIDlet Security
You can adjust security settings for each MIDlets/MIDlet suite by selecting a MIDlet and
choosing Security. Note that some features may not be available for all MIDlets/MIDlet
suites.
Security
Option
Description
Net Access
Determines whether a MIDlets/MIDlet suite can access
the Internet.
Local
Connectivity
Enables a MIDlets/MIDlet suite to access services such
as RDA and Bluetooth. Refer to your Pocket PC Phone's
manual for the features available on your handset.
App Auto Run
Enables a MIDlets/MIDlet suite to run at specified times,
or any time.
Messaging
Determines whether a MIDlets/MIDlet suite can send
and/or receive SMS messages.
Multimedia
Recording
Enables a MIDlets/MIDlet suite to record sounds and
images. Refer to your Pocket PC Phone's manual for the
features available on your handset.
Pocket PC Phone User Manual 149
Error Messages
Message
Meaning
Either RAM shortage, or insufficient
space on the file system
Insufficient memory available on your Pocket
PC Phone.
Network out
No network connection available.
The jar size does not match that
specified in the jad
The installation information provided by the
MIDlet manufacturer is inaccurate.
The jar manifest does not match
the jad
The installation information provided by the
MIDlet manufacturer is inaccurate.
Invalid Java application descriptor
(jad)
There is a problem with the installation file
provided by the MIDlet manufacturer.
Invalid Java archive (jar)
There is a problem with the installation file
provided by the MIDlet manufacturer.
This Java application is not
compatible with this device
One of more features required by this MIDlet is
not available on your Pocket PC Phone.
150 Pocket PC Phone User Manual
Chapter 10
Using Camera and Album
10.1 About Camera and Album
10.2 Camera
10.3 Album
152 Pocket PC Phone User Manual
10.1 About Camera and Album
With Camera Wizard, you can use the attached camera on the back of your device to snap
new photos or shoot video clips with accompanying audio. Album provides many powerful
features to manage, organize, and manipulate the image, video, and audio files.
When in Photo Capture mode, you can capture standard still images. In Video or MMS
Video Capture mode, you can capture “live” video streams (with audio if desired), then
share them with others or play them on your own Pocket PC Phone, or desktop PC.
In Contact Photo Capture mode, you can caputre images for your contacts. Or, in
Picture Theme Capture mode, you can place your captured images into attractive frames
(templates). You can even send the captured files via E-mail, or via MMS. Just Snap and
Send a newly-captured image, or Select and Send an existing image.
Of course, you can also get image, video, and audio files from received E-mail, a Storage
Card, infrared beaming, or synchronized from a PC via ActiveSync, and organize them
into albums and Slide Shows.
File formats supported
File formats that you can browse and view / play in Album include:
File Type
Formats
Still-image formats
BMP
GIF
JPEG
Animation format
Animated GIF
Video formats
Motion-JPEG AVI (.avi)
MPEG-4 Simple profile (.mp4)
3GPP-H.263 baseline (.3gp)
Audio formats
MPEG-4 AAC (Advanced Audio Coding in .mp4 format)
WAV
MIDI (standard MIDI type 0,1, and SP-MIDI)
Pocket PC Phone User Manual 153
NOTE: You can set an audio file to be used as your Pocket PC Phone’s ring tone. For
more information about ring tone settings, please see Chapter 5.
File formats that Camera supports includes:
File Type
Formats
Still-image formats
BMP
JPEG
Video formats
Motion-JPEG AVI (.avi)
MPEG-4 Simple profile (.mp4)
MMS Video formats
3GPP-H.263 baseline (.3gp)
MPEG-4 Simple profile (.mp4)
10.2 Camera
There are two ways to enter the Camera mode :
n Tap the Start menu > Programs > Camera.
n Or just press the uppermost button on the left side of your device.
When you initially enter Camera mode, the Photo Capture mode will be active. The title
at the right lower side of the LCD Display area indicates the current mode. After starting
one capture mode, you can easily switch to another, if desired.
Capture mode
Function
Photo
capture still images
Video
capture video clips
MMS Video
capture video clips and send via MMS
Contact Photo
take a photo to be used as a Photo ID for a contact entry
Picture Theme
capture still images and place in frame
154 Pocket PC Phone User Manual
Usage of Buttons in Camera Mode
When in Camera mode, you can press the following buttons on your Pocket PC Phone
as a shortcut
Camera/Capture
Button
Press to launch Camera.
Press again to take a picture
or to record a video.
Capture/Action
Button
Capture - Press to take a
picture in still image capture
modes. If in video capture
modes, press this button to
start recording the incoming
video stream, and press it
again to stop the recording
process.
Navigation Pad
Up/Down - Increase/
decrease the zoom
levels.
Left/Right - Switch
between capture
modes.
Action - Confirm the selection
you made.
Camera Settings Screen
Press to toggle the Camera Settings
screen open and closed. If the screen
is open and you have made changes
to the settings, press to save the
settings before closing the screen.
Orientation Toggle
By default, the orientation
is in a Portrait display.
Press this button to
change to a Landscape
orientation.
Pocket PC Phone User Manual 155
Photo Capture Mode
In Photo Capture mode, you can capture a single still image by pressing the Capture button
on your Pocket PC Phone, or the Action button on navigation pad. For the information
on setting output format, resolution and ambience, please see Camera Settings Screen
section.
The Camera automatically
calculates the number of photos you
can capture, based on the current
settings and the space available. In
this example, 5019 more photos can
be captured. The counter updates
automatically after a photo taking or
the capture size changing.
This icon indicates a ready
state. It changes to a red dot
during image capture
Capture Sizes are:
n XL = Extra Large (960x1280)
n L = Large (480x640)
n M = Medium (240x320)
n S = Small (120x160)
The current capture size is small.
The current Ambience setting is
shown at this position. This icon
indicates it has been set to Daylight.
The current zoom is 4x, indicating
viewing 4x of normal size.
Incoming video stream is shown using the
entire Pocket PC Phone screen. (Icons
superimposed on the screen are not saved
with your captured images/videos.)
Exits Camera mode and
returns to the previous
screen.
The word Photo indicates
that you are currently in
Photo Capture mode. Tap
the left or right arrow icon to
change capture mode.
Tap to switch to Thumbnail
View of Album mode.
Tap to open the Camera
Settings screen.
Tap the upward-pointing triangular icon
to Zoom IN, or the downward-pointing
triangular icon to Zoom Out.
NOTE: Most of the settings in the LCD Display Panel can be changed using the
Camera Settings screen. Tap on the Camera Settings icon to display the Camera
Settings screen (explained later).
156 Pocket PC Phone User Manual
Video Capture Mode
To start video recording :
1. Switch to Video Capture mode by tapping
navigational pad.
or
icons, or using Left/Right
2. Press the Action button, or the Capture button on the left side of your Pocket
PC Phone.
To stop recording, press Action or Capture button again. The first frame of the newlycaptured video file will be displayed, and Review Screen described earlier will be available.
Output format is either Motion-JPEG AVI or MPEG4, based on the Camera Settings.
The Camera automatically calculates
the available duration for a video
recording, based on the current
settings and the space available.
When recording in progress, it
changes to recording timer. Camera
automatically updates the available
duration after a video taking or the
capture size changing.
Incoming video stream
is shown using the entire
Pocket PC Phone screen.
The green “filmstrip” icon indicates
the camera is in idle/ready state. A
blinking red circle indicates recording
in progress.
In this example, recording has been
in progress for a duration of 21.55
seconds thus far.
Capture Sizes are:
n L = Large (240x320)
n M = Medium (144x176)
n S = Small (96 x128)
The current size is large.
The current Ambience
setting is shown at this
location. This icon
indicates it has set to
Auto.
Exits Camera mode
and returns to the
previous screen.
The word Video indicates
that you are currently in
Video Capture mode.
Tap the left or right arrow
to change capture mode.
Left icon: Tap to open the
Camera Settings screen.
Right icon: Tap to switch
to Thumbnail View of
Album mode.
Tap the upward-pointing/
downward-pointing triangular
icons to Zoom In/Out.
The current zoom is 2x,
indicating viewing 2x of
normal size
Pocket PC Phone User Manual 157
MMS Video Capture Mode
The MMS Video capture mode is convenient if you want to capture a video file and then
send it via MMS.
To start the video recording, press the Action button, or the Capture button on the left
side of Pocket PC Phone. To stop recording manually, press the Action or Capture button
again.
Capture Sizes for MPEG-4
video format are:
n L= Large (240 x 320)
n M= Medium (144 x 176)
n S= Small (96 x 128)
This example is medium size.
In this example, MPEG-4
is selected as the Capture
Format. When recording in
MPEG-4, you have a choice
of either Portrait or Landscape
orientation. Portrait orientation
is shown here.
Ambience has been set to Auto.
When you select H.263 as the Capture Format, only Landscape orientation is available.
Capture Sizes for H.263 video
format are:
n M = Medium (176 x 144)
n S = Small (128 x 96)
This example is medium size.
158 Pocket PC Phone User Manual
Picture Theme Capture Mode
The Picture Theme Capture mode lets you choose a template in which your captured
still image(s) will be placed. You can think of a template as a kind of frame in which you
would insert a photograph. Several templates are included with Camera Wizard, in the
subfolder named \My Documents\Templates\.
To browse and select different templates, do one of the following:
n Tap
n Tap
buttons to display the previous or next template.
, select a template from the Template field.
n Tap
, then tap Browse... button to display detailed information of
templates. Tap Previous or Next button to browse the selection under the
current folder. To change the folder, tap Change... button.
This example template
requires two captured
images. “2/2” indicates
that one image has
already been caputred.
Tap these icons to browse
templates.
Pocket PC Phone User Manual 159
Review Screen
If the Review after capture checkbox is currently checked in the Gerenal tab of Options
screen, then immediately after you capture an image, it will be displayed on the screen
along with four icons.
1. To return to the previous screen, tap the Camera icon.
2. To immediately send a captured image/video, tap the mail icon then select an
option from the Send File dialog box. If in the Contact Photo mode, display
instead. Tap this icon to assign the captured image to a contact.
3. To delete the image press the rubbish bin option.
4. To view and edit the picture tap, the Album icon (for edit options see Album.)
Review Screen:
1
2
3
4
Send via MMS
The MMS composer screen will open, with the newly-captured file already attached. Simply
compose the MMS message as you normally would and send.
160 Pocket PC Phone User Manual
Send via E-Mail
This command invokes the compose screen of Inbox, with the newly-captured file already
attached. Just compose and send the E-mail as you normally would.
Zooming In/Out
In all modes, you can press the Up navigational button on your Pocket PC Phone to Zoom
In the incoming video stream. Each time you press the Up button, the enlargement doubles.
When the zoom reaches its limit, a beep will sound.
Maximum zoom limit is different for each capture mode and capture size. The table below
summarizes the Zoom function availability.
Capture Mode
Video and
MMS Video
Photo and
Contact Photo
Picture Theme
Capture Size Setting
Zoom Available
Large (240 x 320)
1.0x to 2.0x
Medium (144 x 176)
1.0x to 4.0x
Small (96 x 128)
1.0x to 4.0x
XL (960x1280)
1.0x (no zoom available)
Large (480 x 640)
1.0x to 2.0x
Medium (240 x 320)
1.0x to 4.0x
Small (120 x 160)
1.0x to 8.0x
Determined by the current
template.
Depends on the size of the
currently loaded template.
Notes: n MMS Video Capture mode in H.263 file format only has Medium and
Small sizes.
n 1x = normal size (no zoom)
2x = double enlargement
4x = quadruple enlargement
8x = octuple enlargement
Pocket PC Phone User Manual 161
Camera Settings Screen
When in any of the capture modes (Photo, Video, MMS Video,
Contact Photo or Picture Theme), you can tap
to display
the Camera Settings. Or, you can press the Contacts button
at lower left of the front of your Pocket PC Phone.
NOTE: The Capture Size is not available in Pciture Theme
Capture mode. It is replaced by Template drop-down
list and the Browse... button.
Icons on the menu bar are:
1. Switches to the Thumbnail View of Album mode.
2. Switches to the Detailed View of Album mode.
Settings
1 2
Explanation
Capture Mode
Select a mode - Photo, Video, MMS Video, Contact Photo or
Picture Theme.
Capture Format
The choices for Capture Format will be different based on
capture modes.
Capture Size
The choices for Capture Size will be different based on capture
modes. Higher Capture Size settings produce larger file sizes.
Ambience
A list of lighting conditions that lets you adjust the Capture screen
to look its best in various environments.
There are also options that affects the appearance of the
incoming video stream: Grayscale (black and white), Sepia
(reddish tint), Cool (bluish tint), and Negative (darkness and
lightness reversed).
162 Pocket PC Phone User Manual
Tools Menu
The Tools Menu provides many more settings that let you customize the behavior of
Camera mode functions
Adjust...
Adjust... enables you to adjust the display properties: Contrast, Brightness, Saturation,
Hue, and Sharpness.
To open Adjust... screen, tap
> Tools > Adjust....
To adjust a display propertye: select a property from Property field and use the Slider
Bar to adjust the value.
NOTE: The incoming video stream displayed on your screen will immediately show
the effect of any changes you make.
To use original default values, tap Reset button
Options...
The Options screen contains three tabs: General, Image, and Video.
a) General Tab
The General tab includes the following options:
n Disable shutter sound
n Keep backlight on while in viewfinder
n Review after capture
n Flicker adjustment (Auto, 50Hz, or 60Hz)
NOTE: Flicker Adjustment refers to the electrical voltage used in your country.
Pocket PC Phone User Manual 163
b) Image tab
Here are the options that affects on still image captures.
Options
Prefix Type and
Prefix String
Function
By default, the filename of each new captured image file will
be “image” followed by a sequential number, for example:
image_00001.jpg. If you wish to change this prefix to a
different arbitrary text string, select String in the Prefix Type
field and type the desired characters into the Prefix String
field. For example, entering “party” in the Prefix String field
would produce the filename party_00001.jpg.
Alternatively, you can choose Date or Date and Time as the
Prefix Type.
Counter Index
By default, sequential numbers are automatically incorporated
into each filename for all new image files you capture, such
as 00001, 00002, 00003, etc. The number follows the prefix
(explained above).
To reset the numbering to “00001” for your captured image
files, tap Reset counter.
Save to
By default, your captured image files will be saved to your
\My Documents\ folder.
164 Pocket PC Phone User Manual
c) Video tab
The options on the Video tab affect only your captured video files.
Options
Prefix Type and
Prefix String
Function
By default, the filename of each new captured video file will
be “video” followed by a sequential number, for example:
video_00001.avi. If you wish to change this prefix to a different
arbitrary text string, select String in the Prefix Type field and
type the desired characters into the Prefix String field. For
example, entering “vacation” in the Prefix String field would
produce the filename vacation_00001.jpg.
Alternatively, you can choose Date or Date and Time as the
Prefix Type.
Counter Index
By default, sequential numbers are automatically incorporated
into each filename for all new video files you capture, such
as 00001, 00002, 00003, etc. The number follows the Prefix
(explained above). To reset the numbering to “00001” for your
captured video files, tap Reset counter.
Recording with
Audio
When this checkbox is checked, audio will be recorded with
your captured video clips. It is checked by default. Any videos
captured when the checkbox is not checked would be silent (no
accompanying audio).
Save to
By default, your captured video files will be saved to your \My
Documents\ folder.
Pocket PC Phone User Manual 165
10.3 Album
Album allows you to view image and video files, and play audio files. Four view modes
are available: Thumbnail, Detailed, Slide Show, and Full Screen.
To start Album:
• Tap the Start menu > Programs > Album.
• Tap the Album icon in the Camera screen.
Thumbnail view
The first time you enter Album, the Thumbnail view mode will be invoked. By default,
your \My Documents\My Pictures folder will be initially searched. You can manually
change the position of a thumbnail simply by pressing your stylus on it and then dragging
it to the desired location. To select multiple thumbnails, press your stylus in an empty
part of the screen, then drag your stylus across all thumbnails you want to include in the
multi-selection.
1
2
3
7
6 5 4
1. The current folder is shown here. Tap this field if you want to switch to a different
folder.
2. Tap to select a different thumbnail size.
166 Pocket PC Phone User Manual
3. Tap to change the way thumbnails are sorted.
4. Tap to switch to Camera mode.
5. Tap to switch to Slide Show view.
6. Tap to switch to Detailed view. (Or, tap directly on
a thumbnail to load that file into Detailed view.)
Audio or video files will begin playing.
7. An icon in the lower left or right corner of a
thumbnail indicates the following:
- indicates that text annotation has been
associated with this file.
G - indicates an animated GIF file.
V - indicates a video file.
- this speaker icon indicates that audio
annotation has been associated with this file.
To open a pop-up menu that contains frequently used
List View:
commands, tap and hold your stylus on the thumbnail you want to operate on. To view an
image in an enlarged view, or to play a video or audio file, tap the desired thumbnail.
To make an annotation on your file:
The Annotate... command lets you add and remove text or audio annotation for a file.
The particular text and audio recording can then be set to display or play during a slide
show. In the Thumbnail view mode screen, tap on Edit and then select Annotate..., or
select it from the pop-up menu.
To make a text annotation:
If you wish to associate text with the file, enter it in the text box. After text annotation
has been added, will be shown on the file in the thumbnail. A separate text file will be
created for that text.
Pocket PC Phone User Manual 167
To make an audio annotation:
To create an audio recording (either voice or music) as an annotation using your built-in
Pocket PC Phone microphone, tap
to begin recording, tap
to stop recording. After
audio annotation has been added,
will be shown in the thumbnail. A separate .WAV
audio file will be created.
There is no warning when you record over an existing file. Your previous recording will
be overwritten by the new recording. If you have tapped Remove Voice by accident, tap
Cancel.
NOTE: You cannot record an audio annotation for a video file that has sound. This function
is automatically disabled when you work with a video file with sound.
Sending a file via E-mail or MMS
1. Select the desired file, tap Tools, and then select Send via MMS or Send via
E-mail... from the menu.
2. Follow the relevant procedures for sending that type of message.
To set audio files as Ringtones:
Select the desired audio file, then select Set as Ringtone from the Tools Menu (or the
menu that pops up when you tap and hold on a thumbnail). The previous ringtone will be
immediately replaced. A message will display the filename and confirm that the operation
was successful.
Assign to Contact
This command allows you to assign an image as a Photo ID to a Contact entry in your
Pocket Contacts.
1. Choose the image you want to use as a Photo ID.
2. Select Assign to Contact. The Photo Contacts application will be invoked.
The Contact entries in your Pocket Contacts will be displayed.
168 Pocket PC Phone User Manual
3. Select the Contact entry to which you want to assign the Photo ID, and assign
the desired attributes as you normally would in Photo Contacts (Photo only,
or photo with template, etc.).
4. The Photo Contacts Preview screen will show you a preview of how the
Photo ID setup looks. After you save it, Photo Contacts will exit, and you will
automatically be returned to the Album program.
Connect
This command is available on the Tools menu when in Thumbnail View only. It allows you
to connect to a server with media content via the Internet, and play the streaming media.
After selecting Connect... on the Tools menu, enter the desired URL in the “rtsp://” field
provided, then tap OK. If the connection is made succesfully, the media will be played
immediately in the Detailed View mode.
Options
To change the Album settings, tap Options on the Tools menu. Four tabs are available:
General, Association, Slide Show, and Network.
a) The General tab
Following tables are the options in the General tab:
Function
Default zoom
Explanation
The setting in the Default zoom field controls the size of the selected
file when it is initially displayed in Detailed View. If set to Smart,
Album will automatically calculate the best size in which to display
the file on the screen. However, if you want files to initially display
in their original size, select Original size from the drop-down list
box. If you want Camera to automatically display selected files so
that they fit within the screen, select Fit to window.
Pocket PC Phone User Manual 169
Full screen
rotate
If None is selected, no automatic rotation will take place when
a file is displayed in Detailed View (but you can still rotate
the display manually using the Rotate Clockwise and Rotate
Counterclockwise icons on the toolbar in Detailed View). Select
Left to automatically rotate images 90 degrees to the left in Detailed
View, or Right if you want to rotate 90 degrees to the right.
Animation
speed
The setting in the Animation speed field controls the speed at which
animated GIF files are played. By default, this is set to Normal. You
can select Faster, Slower, or No Delay from the drop-down list.
Keep backlight
on while
playing video
If you have set your Backlight to dim after a certain number of
seconds, you can override it by checking this checkbox. This ensures
that the Backlight will not dim during the video playbacks.
Keep system
powered on
during video
and audio
playback
Overriding your system's power settings ensures that the system will
not automatically power off your device whenever a video playback
or audio playback is in progress.
Adjust Gamma
The Adjust Gamma setting controls image brightness/darkness. The
minimum setting of 0.01 will cause images to display very dark. The
maximum setting of 3.00 will cause them to display very light (“wash
out”). If you change this setting, you can conveniently reset it to 1.00
by tapping the Reset button. This feature assists you in viewing an
image more easily under different lighting conditions.
The Association tab
You can associate any or all of the supported file types with Album. When selecting a file
of the associated type in the File Explorer, it will automatically open using Album.
170 Pocket PC Phone User Manual
The Slide Show tab
These settings control only the behavior of Slide Show view mode. These options are
mostly self-explanatory, just choose the item you need and follow the relevant procedures
for the way you want the Slide Show to work.
The Network tab
The settings in this tab are used in conjuction with the Connect... command on the Tools
menu. From the drop-down list in the Connect via field, specify the network to be used
in conjunction with the Tool Menu’s Connect... command. In UDP port range, the values
in these two fields refer to the range of the protocol used to transfer data through the
Internet. These are already assigned to the optimal values by T-Mobile and normally will
not be changed.
Detailed View Mode
Detailed View mode displays the selected file in an enlarged
view, and you can further manipulate the view in various
ways (zoom, rotate, pan, etc.).
1. Toolbar.
2. Command Bar.
3. Hide or display the Toolbar.
4. Switch to Thumbnail view.
5. Switch to Slide Show view.
6. Switch to Camera mode.
1
2
3
4
5
6
Pocket PC Phone User Manual 171
Icons on the Toolbar
Previous file
Next file
Rotate
Clockwise
Rotate Counterclockwise
(90 degrees each time tapped)
Switch to Full
Screen view.
Zoom
Out
Zoom
In
Fit to
window
Toggles the Quick View window
open and closed. Available only
when current file is an image file.
NOTE: Full Screen View will hide the Title Bar, Toolbar, and Command Bar, so the full
screen is utilized for image/video display.
Images too big for the screen
1. Whenever the image is too large to be shown in the display area in its entirety,
you can press your stylus anywhere in the display area and drag to interactively
quick-pan the image to any desired position.
2. Alternatively, you can open the Quick View window, by tapping the Quick View
icon on the Toolbar. The dotted outline within the Quick View window shows
the currently displayed portion, in relation to the entire image. Drag the outline
within the Quick View window to the desired position, or tap within the Quick
View window to jump the outline to a different position. When satisfied with the
position, tap the Quick View icon again to close the Quick View window.
To set as Today wallpaper:
This command allows you to change the background image of the Today screen on your
Pocket PC Phone to any image you want.
1. In Album, tap to open a video file or image you want to use as the image for
the wallpaper.
172 Pocket PC Phone User Manual
2. If desired, you can manipulate it in any way you wish: Zoom In or Out, Rotate,
Pan, etc. The exact state of the image as displayed on your screen will be used
as the Today screen image. Likewise, if you have chosen a video file and do not
wish to use the first frame of the video as the wallpaper, you can start playing
the video and then open the Tools Menu at the frame you want to use. (The
video is paused when the menu is open.)
3. Select Set as Today Wallpaper. The message “The ‘Today’ background
image has been successfully changed” will display.
To Reset the Today Screen back to the Default Wallpaper:
If you later decide that you want to re-set the Today screen back to the original default
background:
1. Tap the Start menu > Settings > Today icon in the Personal tab.
2. Select Windows Default in the list, then make sure the Use this picture as
the background checkbox is checked.
3 Tap OK.
Pocket PC Phone User Manual 173
Slide Show View
When in the Thumbnail view or Detailed view, you can tap the icon in the Command Bar
to enter Slide Show mode.
Tap to re-display the previous
file. Tap repeatedly to quickly
Rewind to the desired file.
(The three leftmost icons
become available after Stop
has been tapped.)
Exits the Slide
Show and enters
the Detailed view.
Tap once (or repeatedly)
to Fast Forward to the
next sequential files.
Tap to resume playing a
Slide Show that has been
stopped.
Exits Slide Show mode
and enters Thumbnail
View mode
Tap to stop playback
and stay on the current
slide, but does not exit
the Slide Show mode.
Slide Show Properties. Lets you set
Transition Effects, Rotation, Text
display, Audio, Delay Time between
slides (for image files), Random or
forward-sequential display, etc. in the
Slide Show Options screen.
174 Pocket PC Phone User Manual
Full Screen View Mode
You can enter the Full Screen View only from the Detailed View. In the Detailed View
mode, simply tap the Full Screen icon on the Toolbar to switch to Full Screen.
Tap to switch to Full Screen
View mode.
As with the Detailed View, if the image
or video is currently displayed in a size
that is too large to fit in its entirety on the
screen, you can “pan” the desired portion
into view by pressing and dragging your
stylus on the screen.
When you are ready to exit the Full
Screen View, tap anywhere on the
screen to display the Toolbar. Tap
the left most icon to exit. If no action
is taken, the Toolbar will automatically
disappear again after a few seconds.
Appendix A
Maintaining your Pocket PC Phone
Adding or Removing Programs
n Managing Memory
n Backing Up Files
n Resetting Your Pocket PC Phone
n
176 Pocket PC Phone User Manual
Adding or Removing Programs
By default, programs added to your device at the factory are stored in the ROM (read only
memory). You cannot remove these programs, and you will never accidentally lose them.
You can install any other programs created for your device, as long as your device has
enough memory. The most popular web site to find software for Pocket PC Phone devices
is http://www.microsoft.com/mobile/pocketpc.
To add programs using ActiveSync:
You will need to save the appropriate software to the hard drive of your PC before installing
it on your device.
1. Download the program to your PC (or insert the CD or disk that contains the program
into your PC). Be sure that the program is compatible with your Pocket PC Phone before
installing it.
2. Read any installation instruction or documentation that came with the program. Many
programs provide their own installation instructions.
3. Connect your device to a PC.
4. Double click on the program's .exe file.
n If the file is an installer, the installation wizard will begin. Follow the
directions on the screen. Once the software has been installed on your PC,
the installer will automatically transfer the software to your device.
n If the file is not an installer, you will see an error message stating that the
program is valid but was designed for a different type of PC. You will need
to move this file to your device. If you cannot find any installation
instructions for the program in the Read Me file or documentation, use
the Explore command in ActiveSync to explore the program file
to the Program Files folder on your device.
Once installation is completed, tap the Start menu > Programs > program icon.
Pocket PC Phone User Manual 177
To add a program directly from the Internet:
1. Determine that your device and processor type meets the requirement of the software that
you want to install.
2. Download the program to your device directly from the Internet using Pocket Internet
Explorer. You should see a single *.xip, *.exe or *.zip file, a setup.exe file, or several
versions of the files for different device types and processors. Be sure to select the program
designed for the Pocket PC Phone.
3. Read the installation instructions, readme files, or documentation that came with the program.
4. Tap the file, such as a *.xip or *.exe file. The installation wizard will begin. Follow the
directions on the screen.
To remove a program:
Tap the Start menu > Settings > System > Remove Programs.
You can only remove programs installed in storage memory. Programs that came with your
device cannot be removed. You can quickly return your device to the factory default configuration by clearing all memory. All data, except the installed ROM application, will be lost.
Managing Memory
Memory on your Pocket PC Phone is shared between the storage memory and the program memory. Storage memory is used to store the information you have created and the
programs you have installed. Program memory is used to run programs on your Pocket PC
Phone. The Pocket PC Phone automatically manages the allocation between the storage
memory and the program memory.
To view memory allocation and availability:
Tap the Start menu > Settings > the System tab > Memory.
178 Pocket PC Phone User Manual
Finding space in storage memory
Under certain situations, such as when the memory is low, your Pocket PC Phone may
not be able to automatically adjust the memory allocation. When you receive a message
stating that storage or program memory is unavailable, try the following solutions:
Move data to a SD storage card
1. Tap the Start menu > Programs > File Explorer.
2. Tap and hold the file you want to move, and tap Cut. Open the My Documents folder in
the storage card folder, tap Edit, and then tap Paste.
Files stored in folders other than My Documents (or in folders under the sub-folders in My
Documents) may not show up in the list view of some programs. When you use Notes,
Pocket Word, or Pocket Excel, move files by opening the item and tapping Tools or Edit
and then Rename/Move.
Move E-mail attachments
1. Tap Messaging > Tools > Options.
2. On the Storage tab, select Store attachments on storage card, and then tap OK. All
existing and future attachments will be automatically stored on the storage card.
Save new items on a storage card
Set programs such as Notes, Pocket Word, and Pocket Excel to automatically save new
items on the storage card.
1. In Notes, Pocket Word, or Pocket Excel > Tools > Options.
2. In the Save to: field select Storage Card.
Pocket PC Phone User Manual 179
Delete unnecessary files
1. Tap the Start menu > Programs > File Explorer.
2. Tap and hold the file, and then tap Delete on the pop-up menu.
To find your largest files, tap the Start menu and then Find. In the Type list, tap Larger
than 64 KB, and then tap Go.
Delete all files and clear the history in Internet
Explorer:
From Internet Explorer > Tools > Options > the Memory tab > Delete Files > Clear
History.
Backing Up Files
Because any new programs or data are stored in RAM, and therefore will be lost if your
device loses power for any reason, it is critical that you back up the device's files to your
PC or a memory card. You can back up files by synchronization while working on a PC.
However, if you are unable to access your PC, you will need to back up files to a SD or
MMC card. Your device enables you to back up individual files in Word or Excel. All files
could be saved on a SD. Furthermore, you can also back up and restore Contacts, Calendar, Internet and Messaging Settings.
SD and MMC Cards
Your device has an expansion slot compatible with a range of SD and MMC Memory cards,
which are primarily used to back up or transfer files and data.
180 Pocket PC Phone User Manual
To insert a memory card:
Push the memory card into its slot until it clicks into place. The card is secure when it is
not protruding from the base.
To remove a memory card
To remove the card, push it in and then release, letting the card spring out.
Backing up or restoring your system using
xBackup:
1. Tap the Start menu > Programs > xBackup > then the Backup or Restore tab.
2. If you have inserted the SD card properly, it will appear next to Target. Tap Open and
select Storage Card under the task bar.
3. Make sure that no applications are running, tap Start.
Backing up or restoring your system via ActiveSync
1. Double click on
in the task bar of your PC.
2. Select the Backup/Restore option in the drop-down menu of Tools in ActiveSync.
3. Select the Backup tab to back up your system. If necessary, select the Restore tab to
restore your system.
Resetting Your Pocket PC Phone
You can perform a soft reset or a full reset. During a soft reset, the device is restarted
and only some data in opened programs may be lost. However, a full reset turns the battery off, returns the device to its original factory settings, and deletes all programs, files,
contacts and other information you have saved to the device. Therefore, it is extremely
important to back up data to a storage card or your computer on a regular basis in the
event that a full reset has to be performed.
Pocket PC Phone User Manual 181
To perform a soft reset
If your Pocket PC Phone responds slowly, stops responding, or freezes, you can soft reset
it. A soft reset causes the Pocket PC Phone to restart and re-adjust memory allocation.
Unsaved data in any opened applications may be lost. Use the stylus to press and hold
the Reset button, as shown below.
To perform a full reset
A full device reset clears memory, deletes all data and restores the Pocket PC Phone to
its default settings. Programs installed at the factory remain, erasing all data that you have
created and programs you have installed. Press and hold the power button, and then use
the stylus to press the soft reset button at the same time. Be sure you have backed up
all your data in a SD card or on your PC before performing a full reset.
182 Pocket PC Phone User Manual
Pocket PC Phone User Manual 183
Appendix B
Regulatory Notices
Regulatory Agency Identification
n European Union Notice
n Important Health and Safety Information
n Troubleshooting
n
184 Pocket PC Phone User Manual
Regulatory Agency IDs
For regulatory identification purposes your product is assigned a model number PM10A.
The following accessories have been approved for use with your device. Their assigned model numbers
listed below can identify these approved accessories. To ensure continued reliable and safe operation
of your Pocket PC Phone, use only the accessories listed below with your PM10A.
Accessories
Model Number
Cradle
PM15x
The above x may be any alphanumeric character or blank denoting external cosmetic changes.
This product is intended for use with certified Class 2 Limited Power Source, rated 5 VDC, maximum
2A power supply unit.
European Union Notice
Products with CE marking comply with the R&TTE Directive (99/5/EC), the EMC Directive (89/
336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European
Community.
Compliance with these directives implies conformity to the following European Norms (in brackets
are the equivalent international standards):
n
EN 60950 (IEC 60950)
Safety of InformationTechnology Equipment.
n
ETSI EN 301 511
Global system for mobile communications (GSM); Harmonized EN for mobile stations in the
GSM 900 and GSM 1800 bands covering essential requirements of article 3.2 of the R&TTE
directive (1995/5/EC ).
n
ETSI EN 301 489-1
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility
(EMC) standard for radio equipment and services; Part 1: Common technical requirements.
Pocket PC Phone User Manual 185
n
ETSI EN 301 489-7
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility
(EMC) standard for radio equipment and services; Part 7: Specific conditions for mobile and
portable radio and ancillary equipment of digital cellular radio telecommunications systems
(GSM and DCS).
n
ETSI EN 301 489-17
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility
(EMC) standard for radio equipment and services; Part 17: Specific conditions for 2.4 GHz
wideband transmission systems and 5 GHz high performance RLAN equipment.
n
ETSI EN 300 328
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission
systems; data transmission equipment operating in the 2.4 GHz ISM band and using spread
spectrum modulation techniques.
n
GSM11.10
n
ANSI/IEEE C.95.1-1992
Specific absorption rate in mobile phone emission condition for body health
n
EN50360, EN50361 for SAR
186 Pocket PC Phone User Manual
Important Health and Safety Information
Retain and follow all product safety and operating instructions. Observe all warnings in the operating
instructions on the product.
To reduce the risk of bodily injury, electric shock, fire, and damage to the equipment, observe the
following precautions.
General Precautions
n
Heed service markings
Except as explained elsewhere in the Operating or Service documentation, do not service any
product yourself. Service needed on components inside these compartments should be done
by an authorized service technician or provider.
n
Damage requiring service
Unplug the product from the electrical outlet and refer servicing to an authorized service
technician or provider under the following conditions:
l Liquid has been spilled or an object has fallen into the product.
l The product has been exposed to rain or water.
l The product has been dropped or damaged.
l There are noticeable signs of overheat-ing.
l The product does not operate normally when you follow the operating instructions.
n
Avoid hot areas
The product should be placed away from heat sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that produce heat.
n
Avoid wet areas
Never use the product in a wet location.
n
Avoid pushing objects into product
Never push objects of any kind into cabinet slots or other openings in the product. Slots and
openings are provided for ventilation. These openings must not be blocked or covered.
n
Mounting Accessories
Do not use the product on an unstable table, cart, stand, tripod, or bracket. Any mounting of the
product should follow the manufacturer's instructions, and should use a mounting accessory
recommended by the manufacturer.
Pocket PC Phone User Manual 187
n
Avoid unstable mounting
Do not place the product with an unstable base.
n
Use product with approved equipment
This product should be used only with personal computers and options identified as suitable
for use with your equipment.
n
Adjust the volume
Turn down the volume before using headphones or other audio devices.
n
Cleaning
Unplug the product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning, but NEVER use water to clean the LCD screen.
Safety Precautions for Power Supply Unit
n
Use the correct external power source
A product should be operated only from the type of power source indicated on the electrical
ratings label. If you are not sure of the type of power source required, consult your authorized
service provider or local power company. For a product that operates from battery power or
other sources, refer to the operating instructions that are included with the product.
n
Handle battery packs carefully
This product contains a Li-ion Polymer battery. There is a risk of fire and burns if the battery
pack is handled improperly. Do not attempt to open or service the battery pack.
Do not disassemble, crush, puncture, short external contacts or circuits, dispose of in fire or
water, or expose a battery pack to temperatures higher than 60oC (140oF).
Warning: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. TO REDUCE RISK
OF FIRE OR BURNS, DO NOT DISASSEMBLE, CRUSH, PUNCTURE, SHORT EXTERNAL CONTACTS,
HEAT ABOVE 60oC (140oF), OR DISPOSE OF IN FIRE OR WATER. REPLACE ONLY WITH SPECIFIED
BATTERIES. RECYCLE OR DISPOSE OF USED BATTERIES ACCORDING TO THE LOCAL REGULATIONS
OR REFERENCE GUIDE SUPPLIED WITH YOUR PRODUCT.
SAR Information
n
SAR : 0.413 W/kg @10g (Europe);0.773 W/kg @1g (Taiwan);
188 Pocket PC Phone User Manual
Troubleshooting
If you still encounter problems after reviewing this troubleshooting guide, contact your mobile
operator or an authorized Technical Support center in your area.
Operating Problems
Problem
n
My Pocket PC Phone keeps
turning itself off.
n My Pocket PC Phone is not
making any sound.
Solution
Your Pocket PC Phone is designed by default to turn itself off if
not used for 3 minutes. This period can be adjusted to a maximum
of 5 minutes. Refer to the Power setting in Chapter 5 for more
information.
1 Tap
at the right side of the Title Bar to check the volume
status.
2 Check the settings of Sound and Notifications on the
Personal tab by tapping the Start menu > Settings.
n My Pocket PC Phone does not
vibrate when the phone rings or
alarms occur.
1 Tap
at the right side of the Title Bar to check if the vibrate
function is activate.
2 Check the settings of Sound and Notifications on the
Personal tab by tapping the Start menu > Settings.
3 Check the event note in your Calendar to see if the Reminder
has been activated.
n The screen freezes or the device
is not responding.
Reset your device. See the Resetting your Pocket PC Phone
in Appdendix A.
Pocket PC Phone User Manual 189
Problem
n The screen is dark.
Solution
1 Check the Brightness setting by tapping the Start menu > Settings
> the System tab > the Backlight > Brightness tab.
2 Prolonged exposure to direct sunlight may also cause your Pocket
PC Phone screen to temporarily darken. This is normal for LCD
screens and is not permanent.
n A Running out of memory
warning message pops up on
the screen.
Memory on your Pocket PC Phone is shared between storage memory
and program memory:
1 Delete any unnecessary information you have entered to release
more storage memory space.
2 Delete the unnecessary programs you have installed to release
more program memory space.
See the Managing Memory section in Appendix A.
n The Battery low warning
message pops up on the
screen.
Plug the AC power in to your device to charge it.
n The screen is hard to read, or
the text on the screen is too small
If you are having a hard time viewing a document in Notes, try
changing the size of the view by tapping a zoom percentage on the
Tools menu.
for you.
1 For Pocket Word and Pocket Excel, on the View menu, tap Zoom
and then select a zoom percentage.
2 For Pocket Internet Explorer, on the View menu, tap Text Size
and then select a size.
3 For Pocket Outlook data, try enlarging the display font. To do this
within Calendar, Tasks or Contacts, tap Tools, then Options, and
then select Use large font.
190 Pocket PC Phone User Manual
Tapping and Writing Problems
Solution
Problem
n
Device buttons do not re-spond,
Check the Buttons setting to see if the program assignment for
or bring up the wrong program.
each function button is set as you wanted. Tap the Start menu >
Settings > the Personal tab > Buttons. For detailed information
about Button settings, see Chapter 5.
n
Inaccurate response to stylus
Adjust the touchscreen to respond more accurately to screen
taps.
taps. Tap the Start menu > Settings > the System tab > Screen
> Align Screen.
n
Pocket PC Phone does not
For your Pocket PC Phone to recognize your handwriting input
recog-nize handwriting.
with the stylus, you need to use Transcriber writing. To learn
how to write in Transcriber, see Chapter 2.
Pocket PC Phone User Manual 191
ActiveSync Problems
Solution
Problem
n
ActiveSync operation cannot be
performed or connected.
1
Make sure the ActiveSync cradle/cable is connected
securely.
2
Make sure you have installed the ActiveSync software
included on the Companion CD.
3
Make sure you selected the appropriate local USB from File
Menu Connection Settings in the ActiveSync Manager
window on your desktop computer.
4
If ActiveSync still doesn't work, remove and re-install the
ActiveSync software on your PC.
n
ActiveSync is connected, but
data cannot be synchronized.
On your desktop computer, check the Tools Menu > Options
> the Sync Options tab in the ActiveSync Manager window
to see if the information type for the program you want has
been selected for synchronizing. See more details about
synchronizing information in Chapter 4.
192 Pocket PC Phone User Manual
Connection Problems
Solution
Problem
n
1
Line up the IR ports so that they are unobstructed and within
2
Make sure that nothing is obstructing the two IR ports.
3
Adjust the room lighting. Some light sources interfere with
Unable to use Infrared (IR) port
to transfer information.
a close 20cm range.
IR connections. Try moving to a different location or turn out
some lights.
4
Transfer only one file, or no more than 25 contact cards, at
a time.
n
Cannot connect to Internet, web
1
surfing doesn't work.
Check that you have set up and connected to an Internet
service provider.
2
Check that the wireless connection to your mobile service
provider is switched on and the signal is un-obstructed.
3
Verify with your Internet service provider that your username
and password are correct.
See Chapter 7, Getting Connected. Additional information is
also available in Connections Help on the Pocket PC Phone
and ActiveSync Help on the PC.
Pocket PC Phone User Manual 193
Problem
n
Solution
Problems with the cable and
1
Make sure that your Pocket PC Phone is turned on.
cradle connection.
2
Make sure that you do not have any other active connections.
Tap the Start menu > Today, and then tap
or
at the
bottom of the screen, and then Disconnect.
3
Make sure that the cable is securely plugged into the COM
or USB ports on the back of your PC. Use the cable that
came with the Pocket PC Phone without any extra cables
or extenders attached.
4
Plug the other end of the cable securely into the correct port
on your Pocket PC Phone. If you are using a cradle, push
your Pocket PC Phone securely into the cradle.
194 Pocket PC Phone User Manual
Specifications
System Information
Expansion Slots
Processor
Intel Bulverde CPU at 416MHz
Memory
- ROM : 64 MB
- RAM : 64 MB
SDIO/MMC
supports
Operating System Windows Mobile2003TM
2003 Second Edition
Display
LCD Type
2.8" transflective TFT-LCD
with back-light LEDs,
touch-sensitive screen
Resolution
240 x 320 at 65,536 colors
GSM/GPRS (Tri-band) Module
GSM 900
880 ~ 915, 925 ~960 MHz
GSM1800
1710 ~ 1785, 1805 ~ 1880 MHz
GSM1900
1850 ~ 1910, 1930 ~ 1990 MHz
Internal antenna
Yes
Camera Module
Type
Color CMOS camera module
with dust-proof cover
Resolution
1.3M with JPEG encoder
Camcorder
QCIF, Min 15 fps (in live mode),
Max. 15 seconds per clip
Physical
Dimensions
58 mm (w) x 108.2 mm (h) x 18.2 mm(l)
Weight
150g (with battery)
Yes
Controls and Lights
Navigation
Buttons
5-way navigation pad
- 4 program buttons :
Calendar, Contacts, Camera,
Voice record/Voice command.
- 2 phone function: Call, End
- Volume control button
(Up/ Down)
- Power on/off
- Reset button
LED
- Event notification
- Charge status
- GSM/GPRS signals
- Bluetooth, system
notification
Audio
Audio controller
AGC
Microphone/
Speaker
Built-in
Headphone
WAV/WMA/AMR/MARWB//
AAC/AAC+/MP3 stereo
Connection
Infrared
SIR
I/O port
Mini-USB individual port for
signals
(for USB, and power)
Audio
Stereo headphone jack
Pocket PC Phone User Manual 195
Index
A
About 81
Accessories 15
ActiveSync 68
ActiveSync Errors 74
AC Adapter 15
Add programs 176
Add ring tone 85
Album 165
B
Background 138
Backing Up Files 179
Backlight 11,82
Battery 13
Beam 98
Block Recognizer 28
Bluetooth 94
Bluetooth Connection 73
Bluetooth modes 95
Bluetooth Settings 95
Bonds 96
Buttons 78
Call forwarding 86
Call History 47,56
Call on hold 53
Call waiting 86
Camera 10,153
Camera Lens 11
Car Antenna Connector 11
ClearVue PDF 142
ClearVue PPT 139
Clock & Alarms 82
Command bar 23
Conference call 53
Connection 44
Connections 88
Contacts 10,46,108
Contacts information 55
CSD Line Type 90
D
Data retention 13
Detailed View Mode 170
Device Settings 76
Dialer screen 42
Drawing 35
C
E
Calendar 10,106
Call barring 86
E-Mail 116
E-mail attachments 178
Earphone Plug 11
Editing and selecting text 29
Emergency call 64
End 10
Entering Information 25
F
Finding Information 38
Flight Mode 45
Full reset 181
Full Screen View Mode 174
G
GPRS Settings 90
H
Headset 15
I
Indicators 21
Infrared 73
Infrared Port 11
Input 78
Input Panel 26
International call 64
196 Pocket PC Phone User Manual
Internet 88
Muting a call 54
K
N
Keypad tone 85
Letter Recognizer 27
Locking the keypad 65
Locking the SIM card 66
Locking your Pocket PC
Phone 65
Navigation bar 23
Navigation Pad 10
Network 85
Network card 92
Network Cards Settings 92
Normal Viewer 140
Notes 112
Notifications 22
Notification LEDs 10
M
O
Managing Memory 177
Memory 82
Memory card 180
Menus 79
Microphone 11
MIDlet Manager 143
Mini USB Connector 11
MMC/SD or SDIO slot 10
MMS Messages 123
MMS Settings 129
MMS Video Capture Mode
157
More 86
MSN Messenger 121
Owner Information 79
L
P
Permanent Save 83
Personal tab 76
Phone dialer screen 42
Phone Pad 30
Phone Settings 84
Phone volume 45
Photo Capture Mode 155
Photo Contacts 57
Pictures 135
Picture Theme Capture Mode
158
PIN 44
Pocket Excel 133
Pocket Internet Explorer 91
Pocket Word 132
Pop-Up menus 22
Power 83
Power Button 11
Presentation 140
Programs 24
R
Record 10
Recording 36
Remove a program 177
Review Screen 159
Ring tone 84
Ring type 84
S
Screen Orientation 19
SD and MMC Cards 179
SD storage card 178
Secure your phone 65
Self-portrait mirror 11
Services 86
SIM Card 12
Pocket PC Phone User Manual 197
SIM contact 55
SIM Manager 55
SIM Tool Kit 64
Slide show 141,172
Smart Dialing 49
Soft Keyboard 26
Soft Reset 11,181
Sounds and Notifications 80
Speakerphone 54
Speed Dial 48
Stylus and Stylus Slot 11
Synchronizing Information 70
System tab 77
T
Talk/Send 10
Tasks 111
Terminal Services Client 93
Text Messages 116
Thumbnail view 165
Today 80
Today screen 20
Today wallpaper 171
Today wallpaper 138
Touch Screen 10
Transcriber 28
Transferring pictures 136
U
USB Cable 15
V
Vibrate mode 45
Video Capture Mode 156
VoiceDial 10
Voice Mail 48
Volume 10
W
Wallpaper 172
Windows Media Player 134
Wireless Modem 100
Writing 33