High Definition PoE IP Phone (1-Line)

High Definition PoE IP Phone
(1-Line)
VIP-1010PT
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Copyright
Copyright (C) 2014 PLANET Technology Corp. All rights reserved.
The products and programs described in this User’s Manual are licensed products of PLANET
Technology. This User’s Manual contains proprietary information protected by copyright, and
this User’s Manual and all accompanying hardware, software, and documentation are
copyrighted.
No part of this User’s Manual may be copied, photocopied, reproduced, translated, or reduced
to any electronic medium or machine-readable form by any means by electronic or
mechanical including photocopying, recording, or information storage and retrieval systems,
for any purpose other than the purchaser's personal use, and without the prior written
permission of PLANET Technology.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments
and applications, and makes no warranty and representation, either implied or expressed,
with respect to the quality, performance, merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET
disclaims liability for any inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent
a commitment on the part of PLANET. PLANET assumes no responsibility for any inaccuracies
that may be contained in this User’s Manual. PLANET makes no commitment to update the
information in this User’s Manual, and reserves the right to make improvements on this User’s
Manual and/or on the products described in this User’s Manual at any time without notice.
If users find information in this manual that is incorrect, misleading, or incomplete, we would
appreciate their comments and suggestions.
CE Mark Warning
The is a class B device. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
-2-
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Energy Saving Note of the Device
This power required device does not support standby mode operation. For energy saving,
please remove the DC-plug or push the hardware Power Switch to OFF position to disconnect
the device from the power circuit.
Without removing the DC-plug or switching off the device, the device will still consume power
from the power circuit. In view of Saving the Energy and reducing the unnecessary power
consumption, it is strongly suggested to switch off or remove the DC-plug from the device if
this device is not intended to be active.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of
the presence of hazardous substances in electrical and electronic equipment, end
users of electrical and electronic equipment should understand the meaning of the
crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal
waste and have to collect such WEEE separately.
Trademarks
The PLANET logo is a trademark of PLANET Technology. This documentation may refer to
numerous hardware and software products by their trade names. In most, if not all cases,
their respective companies claim these designations as trademarks or registered trademarks.
Revision
User’s Manual on PLANET SIP PoE IP Phone:
Model: VIP-1010PT
Rev: 1.0 (June, 2014)
Part No. EM-VIP-1010PT_v1.0
-3-
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Table of Contents
1
INTRODUCTION.................................................................................. 7
1.1
FEATURES ........................................................................................9
1.2
APPLICATION .................................................................................. 11
1.3
PRODUCT SPECIFICATIONS .................................................................. 12
1.4
PHYSICAL SPECIFICATIONS AND PACKAGING .............................................. 14
1.5
KEYPAD ........................................................................................ 15
2
INITIAL CONNECTION AND LOGIN ................................................... 19
3
LCD BASIC FUNCTIONS .................................................................... 21
3.1
MAKING A CALL ............................................................................... 21
3.1.1
Call Device............................................................................. 21
3.1.2
Call Methods .......................................................................... 21
3.2
ANSWERING A CALL ........................................................................... 21
3.3
MUTE ........................................................................................... 22
3.4
CALL HOLD / RESUME FORWARD ........................................................... 22
3.5
DND (DO NOT DISTURBED) ................................................................ 22
3.6
CALL WAITING ................................................................................ 22
3.7
CALL FORWARD ............................................................................... 23
3.8
CALL TRANSFER ............................................................................... 23
3.8.1
Blind Transfer ......................................................................... 23
3.8.2
Consultation Transfer............................................................... 24
3.9
THREE-WAY CONFERENCE CALL .............................................................. 24
3.10
CALL PARK .................................................................................. 25
3.11
PICKUP ...................................................................................... 25
3.11.1
Specified Pickup................................................................... 26
3.11.2
Group Pickup....................................................................... 26
3.12
SPEED DIAL ................................................................................ 26
3.13
AUTO-REDIAL ............................................................................... 27
3.14
HOT LINE.................................................................................... 27
3.15
INTERCOM .................................................................................. 27
3.16
HOTDESKING ............................................................................... 28
3.16.1
Set the HotDesking Key ........................................................ 28
3.16.2
HotDesking Feature: ........................................................... 28
3.17
4
APPLICATION ............................................................................... 29
3.17.1
Text Message ...................................................................... 29
3.17.2
Voice Message ..................................................................... 31
LCD ADVANCED SETTINGS................................................................ 33
4.1
BASIC SETTINGS .............................................................................. 33
4.1.1
Language .............................................................................. 33
-4-
High Definition PoE IP Phone (1-Line)
VIP-1010PT
4.1.2
Date & Time........................................................................... 33
4.1.3
Backlight ............................................................................... 34
4.1.4
Password Setting .................................................................... 34
4.2
Phone Volume ........................................................................ 34
4.2.2
Ring Tones ............................................................................. 35
4.3
PHONE BOOK .................................................................................. 35
4.3.1
Local Phone Book.................................................................... 35
4.3.2
Add contacts manually............................................................. 35
4.3.3
Add Contacts from All Calls History: ......................................... 36
4.3.4
Search Contacts ..................................................................... 36
4.3.5
Blacklists ............................................................................... 36
4.3.6
Remote Phone Book ................................................................ 36
4.4
HISTORY MANAGEMENT ...................................................................... 37
4.5
SYSTEM CUSTOMIZATIONS .................................................................. 37
4.5.1
Programmable keys................................................................. 37
4.5.2
SIP Account management ........................................................ 38
4.6
5
SOUND SETTINGS............................................................................. 34
4.2.1
BASIC NETWORK SETTINGS ................................................................. 38
4.6.1
DHCP Mode............................................................................ 38
4.6.2
Static IP Mode ........................................................................ 39
4.6.3
PPPoE Mode ........................................................................... 39
4.7
RESET TO FACTORY ........................................................................... 39
4.8
REBOOT ........................................................................................ 39
WEB CONFIGURATION...................................................................... 40
5.1
WAYS TO CONFIGURE......................................................................... 40
5.2
SETTING VIA WEB BROWSER ................................................................. 40
5.3
STATUS / BASIC .............................................................................. 41
5.4
ACCOUNT / BASIC ............................................................................ 42
5.5
ACCOUNT->ADVANCED ...................................................................... 44
5.6
NETWORK / BASIC ............................................................................ 47
5.7
NETWORK / ADVANCED ...................................................................... 48
5.8
PHONE/TIME/LANGUAGE ..................................................................... 50
5.9
PHONE / PREFERENCE ........................................................................ 52
5.10
PHONE / CALL FEATURE ................................................................... 53
5.11
PHONE / VOICE ............................................................................ 56
5.12
PHONE/KEY/DISPLAY...................................................................... 58
5.13
PHONE / RING TONES ..................................................................... 59
5.14
PHONE / TONES ............................................................................ 60
5.15
PHONE / DIAL PLAN ....................................................................... 61
5.16
PHONE –>ACTION URL................................................................... 63
5.17
PHONE BOOK->LOCAL PHONE BOOK .................................................... 65
5.18
PHONE BOOK->REMOTE PHONE BOOK.................................................. 66
-5-
High Definition PoE IP Phone (1-Line)
VIP-1010PT
6
5.19
PHONE BOOK->CALL LOG ................................................................ 67
5.20
PHONE BOOK->LDAP .................................................................... 68
5.21
PHONE BOOK->BROADSOFT ............................................................. 69
5.22
UPGRADE->BASIC ......................................................................... 70
5.23
UPGRADE->ADVANCED ................................................................... 71
5.24
SECURITY->BASIC ........................................................................ 73
5.25
SECURITY->ADVANCED ................................................................... 74
APPENDIX ........................................................................................ 75
6.1
DIGIT-CHARACTER MAP TABLE .............................................................. 75
6.2
FREQUENTLY ASKED QUESTIONS LIST ..................................................... 75
-6-
High Definition PoE IP Phone (1-Line)
VIP-1010PT
1 Introduction
Cost-effective, High-performance PoE VoIP Phone
To build high-performance VoIP communications at a low cost, PLANET has
integrated high-definition voice into a cost-effective SIP phone. It complies with
IEEE 802.3af PoE interface for flexible deployment. The VIP-1010PT makes it simple
for the enterprise featuring voice and data system or expanding voice system to
new locations.
It helps the company to save money on long-distance calls; for
example, the remote workers can dial in through a Unified VoIP Communication
System just like an extension call but no long-distance call charge would occur. The
VIP-1010PT also allows call to be transferred to anyone at any location within the
voice system, which enables the enterprise to communicate more effectively and is
helpful to streamline business processes.
-7-
High Definition PoE IP Phone (1-Line)
VIP-1010PT
High-quality HD VoIP Voice
The VIP-1010PT delivers HD voice (High-definition Voice) which is the next
generation of voice quality for telephony audio, making the quality of voice better
than that (toll quality) of the standard digital telephony and even close to that of a
room conversation. HD voice is transmitted in the audio frequency range of 50 Hz to
7 kHz or higher over telephone lines, resulting in higher quality voice and clearer
communication.
Standard Compliance
The VIP-1010PT supports Session Initiation Protocol 2.0 (RFC 3261) for easy
integration with general voice over IP system. The VIP-1010PT is able to broadly
interoperate with equipment provided by VoIP infrastructure providers, thus
enabling them to provide their customers with better multi-media exchange
services.
-8-
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Enhanced, Full-Featured Business IP Phone
The VIP-1010PT is a full-featured, enhanced business IP Phone that addresses the
communication needs of the enterprises. It provides 1 voice line and dual
10/100Mbps Ethernet. Furthermore, the VIP-1010PT delivers user-friendly design
containing a 132x64 graphic LCD with white backlight.
The VIP-1010PT supports all kinds of SIP-based phone features including LDAP, Call
Waiting, Auto Answer, Music on Hold, Caller ID 3-way Conferencing, Call on Hold,
Call Forwarding, Black List, DTMF Relay, In-Band, Out-of-Band (RFC 2833) and SIP
Info, among others. Besides office use, the VIP-1010PT is also the ideal solution
for VoIP service offered by Internet Telephony Service Provider (ITSP).
1.1 Features
¾ Highlights
„
Supports SIP 2.0 (RFC3261)
„
Supports 1 SIP voice line
„
IEEE 802.3af Power over Ethernet compliant
„
Supports HD voice
„
LDAP/ TR-069 / SNMP
¾ Phone Features
„
1 line (supporting 1 SIP account)
„
Supports call waiting, call forwarding, call transfer
„
3-way conferencing
„
Call on hold, mute, auto-answer, redial
„
Phonebook (500 groups), blacklist (100 groups), call logs (100 entries)
„
5 remote phone book URL supported
„
Keypad Lock
„
DND (Do Not Disturb)
-9-
High Definition PoE IP Phone (1-Line)
VIP-1010PT
„
Volume adjustable, ring tones selectable
„
Call Pickup/Group Call Pickup
„
Speed Dial
„
Intercom
„
Daylight Saving
„
Network Packet Capture
„
Country Ringtone Signal
„
Direct IP Call
„
Auto Redial / Hot Desking
„
Hotline / XML Browser / Action URL
„
Multi-Languages: Default: English and Simple Chinese
¾ IP PPX Features
„
HD Voice
„
Dial Plan
„
SMS, Voicemail, MWI Message Notification
„
Wideband Codec: G.722
„
Narrowband Codec: PCMA, PCMU, G.729, G.722, G723_53, G23_63,G726_32
„
VAD, CNG , Echo Canceller
„
Full-Duplex Speakerphone
¾ Security Features
„
Supports HTTPS (SSL)
„
Supports SRTP for Voice Data Encryption
„
Supports Login for Administration
„
SIP Over TLS
¾ Network Features
„
SIP V1(RFC2543), V2(RFC3261)
„
Static IP/DHCP for IP configuration
„
3 DTMF modes: In-Band, RFC2833, SIP INFO
„
HTTP/HTTPS Web Server for Management
„
NTP for Auto Time Setting
- 10 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
¾ Administration Features
„
Auto provisioning using FTP/TFTP/HTTP/HTTPS/PnP
„
Dial through IP PBX using Phone Number
„
Dial through IP PBX using URL Address
„
Configuration Managements with Web, Keypad on the phone and Auto Provisioning
„
SNMP
„
TR069
1.2 Application
Enterprise IP PBX Deployment of VIP-1010PT
The VIP-1010PT is much easier to install and configure than the traditional
phone system. Its low cost and high-definition voice quality give you value
for money. Base on standard SIP 2.0, it is compatible with all the standard
SIP-based servers.
- 11 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
1.3 Product Specifications
Product
VIP-1010PT
Hardware
Lines (direct numbers)
1-line cost-effective IP phone
Display
132 x 64 graphic LCD with blue backlight
Feature Keys
4 Soft Keys
10 Programmable Keys
Protocols and Standard
MAC Address (IEEE 802.3)
IPv4 (RFC 791)
Address Resolution Protocol (ARP)
DNS: A record (RFC 1706), SRV record (RFC 2782)
Dynamic Host Configuration Protocol (DHCP) client (RFC 2131)
TCP (RFC 793)
Data Networking
User Datagram Protocol UDP (RFC 768)
Real-time Protocol RTP (RFC 1889, 1890)
Real-time Control Protocol (RTCP) (RFC 1889)
Simple Network Time Protocol (SNTP) (RFC 2030)
Backward compatible with RFC 2543
Session Timer (RFC 4028)
SDP (RFC 2327)
SIP version 2 (RFC 3261, 3262, 3263, 3264)
Message Waiting Indicator (RFC 3842)
Voice algorithms:
- PCMA
- PCMU
- G.729
Voice Gateway
- G.722
- G723_53
- G23_63
- G726_32
Dual-tone Multi-frequency (DTMF), In-Band and Out-of-Band (RFC
2833) (SIP INFO)
Voice Activity Detection (VAD) with Silence Suppression
- 12 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Comfort Noise Generation
Echo Cancellation Message
Features
1 line (supporting 1 SIP account)
Supports call waiting, call forwarding, call transfer
3-way conferencing
Call on hold, mute, auto-answer, redial
Phonebook (500 groups), blacklist (100 groups), call logs (100
entries)
5 Remote Phone Book URL supported
LDAP
DND (Do Not Disturb)
Volume adjustable, ring tones selectable
Call Pickup/Group Call Pickup
Phone Features
Speed Dial
Intercom
Daylight Saving
Network Packet Capture
Country Ringtone Signal
Direct IP Call
Auto Redial
Hotline
XML Browser
Hot Desking
Keypad Lock
Action URL
Multi-Languages: Default: English and Simple Chinese
HD Voice
Dial Plan
SMS, Voicemail, MWI Message Notification
IP PBX Features
Wideband Codec: G.722
Narrowband Codec: PCMA, PCMU, G.729, G.722, G723_53, G23_63,
G726_32
VAD, CNG, Echo Canceller
Full-Duplex Speakerphone
Security Features
Supports HTTPS (SSL)
- 13 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Supports SRTP for Voice Data Encryption
Supports Login for Administration
SIP Over TLS
Dial without Register
SIP V1(RFC2543), V2(RFC3261)
Static IP/DHCP for IP configuration
Network Features
3 DTMF modes: In-Band, RFC2833, SIP INFO
HTTP/HTTPS Web Server for Management
NTP for Auto Time Setting
Auto provisioning using FTP/TFTP/HTTP/HTTPS/PnP
Dial through IP PBX using Phone Number
Dial through IP PBX using URL Address
Administration Features Configuration Managements with Web, Keypad on the phone and
Auto Provisioning
SNMP
TR069
Environments
Power Requirements
5V DC, 1.2A
IEEE 802.3af
Operating Temperature
0 ~ 40 degrees C
Operating Humidity
10 ~ 65% (non-condensing)
Weight
651g (without box) / 920g (with box)
Dimensions (W x D x H)
193 x 190 x 35 mm
Emission
CE, FCC
Two 10/100BASE-T RJ-45 Ethernet ports
Handset: RJ-9 connector
Connectors
Headset: RJ-9 connector
DC power jack
Built-in speakerphone and microphone
- 14 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
1.4 Physical Specifications and Packaging
Physical Specifications
¾
Dimensions
Dimensions (L x W x H)
193 x 190 x 35 mm
Net Weight
651g (without box) / 920g (with box)
BASIC PACKAGING
„
SIP IP Phone Unit
„
Quick Installation Guide
„
RJ-45 Cable x 1
„
Stand x 1
1.5 Keypad
¾
Keypad, LED, and Function Key Definitions
- 15 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Keypad Description
Key
Key Name
Function Description
Assists you in selecting an item that you want to process
Navigation
under the menu by pressing the Up, Down, Right or Left
key. Press the OK key to save.
Key combination includes functions such as
Soft Keys
1/2/3/4
History/Favorites/Redial/CallReturn/HotDesking/DND/Menu/M
SG/Status/Book/FWD/PickUp/Group
PickUp/Intercom/Speed
Dial/and so on.
Home
Back to the Home page
Book
View Local Phone Book/Blacklist/Remote Phone Book
Headset
Use the headset to call out or call in
Forward
Forward the call to the third party
Redial
View the Missed Calls, Incoming Calls and Dialed Calls.
Press this key in calling mode and you can hear the other side,
Mute
but the other side cannot hear you.
Turn down or turn up the volume by pressing the “-” key or the
Volume -/+
“+” key.
Hands-free
Make the phone into hands-free mode.
Digital
Input the phone number or DTMF.
Keyboard
Indicator
Blinking light indicates there is an incoming call.
light
- 16 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Rear View and Panel Descriptions
¾
Keypad Description
Port
Port Name
Description
Power Switch
Input: 5V DC, 1.2A
Internet
10/100M Connect it to Network
PC
10/100M Connect it to PC
Handset
Port type: RJ-9 connector
Headset
Port type: RJ-9 connector
- 17 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Account and Status Display
Port Name
Description
Register success
Register failure
Registering
Deactivated account
Auto answer
No disturb
Always forward
Network disconnection
Ring off
Headset mode
New voice message
New text message
Missed calls
- 18 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
2 Initial Connection and Login
The package should contain the following items plus the VIP-1010PT. If any item is
missing or damaged, please contact the seller immediately.
Quick Installation Guide
Handset
Handset Cord
RJ-45 Cable
Stand
Step 1. Handset Connection
Plug one end of the handset cord into the handset and the other end into the
handset jack
Step 2. Connecting Power System
The VIP-1010PT can be powered either by its external AC/DC adapter or by
connecting to an IEEE 802.3af/at PSE device such as 802.3af injector / hub or
802.3af/at POE switch. Once the VIP-1010PT is powered, the LCD screen will
prompt for POST.
Note 1: This unit does not include the 5V/1.2A power adapter.
Note 2: Only WAN supports POE.
- 19 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Step 3. Connecting Network
Step 4. Computer Network Setup
Set User computer’s IP address to 192.168.0.x, where x is a number between 2 to
254 (except 1 where is being used for the phone by default). If User don’t know how
to do this, please ask User network administrator.
Connecting User PC to the VIP-1010PT PC port.
Step 5. Login Prompt
Use Web browser (Internet Explorer 6.0 or above) to connect to 192.168.0.1 (type
this address in the address bar of Web browser).
User’ll be prompted to input user name and password: admin and 123
- 20 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
3 LCD Basic Functions
3.1 Making a call
3.1.1 Call Device
User can make a phone call via the following methods:
1. Pick up the handset,
icon will be shown on the idle screen.
2. Press the Hand-free key,
icon will be shown on the idle screen.
3. Press the Headset key if the headset is connected to the Headset Port in advance.
The
icon will be shown on the idle screen.
User can also dial the number first, and then choose the method user will use to
speak to the other party.
3.1.2 Call Methods
User can press an available line key if there is more than one account, then
1. Dial the number user wants to call.
2. Press History soft key. Use the navigation keys to highlight user choice (press
Left/Right key to choose Missed Calls, Incoming Calls and Outgoing Calls).
3. Press the Redial key twice to call the last number called or press Redial key to
enter All Calls interface to choose the number to dial out.
4. Press the programmable keys which are set as speed dial keys. Then press the
Send key or Dial soft key to make the call if necessary.
3.2 Answering a call
1. If user is not on another phone call, lift the handset to use, or press the Speaker
key/Answer soft key to answer using the speaker phone, or press the Headset key
to answer the headset.
2. If user is on another phone call, press the answer soft key to answer new
- 21 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
incoming and hold the current talking. During the conversation, user can alternate
between Headset, Handset and Hand-free by pressing the corresponding keys.
Note: The
will flash during the Incoming interface
3.3 Mute
User can press the Mute key
to make the user NOT be heard by the other party,
but user can hear the other party. Icon
will be shown on the LCD, and press the
Mute key again to recover.
3.4 Call Hold / Resume Forward
1. Press the Hold button or Hold soft key to put user active call on hold.
2. If there is only one call on hold, press the hold soft key to retrieve the call.
3. If there is more than one call on hold, press the line button, and the Up/Down
button to highlight the call, and then press the Resume button to retrieve the call.
3.5 DND (Do Not Disturbed)
If user enables the DND mode, the phone will reject to answer all calls automatically
and play busy tone; the UI will present missed calls at the same time.
3.6 Call Waiting
To configure Call Waiting via Phone interface:
1. Press Menu -->Features-->Call Waiting-->Enter, ;
2. Use the Left or Right key to activate or deactivate call waiting.
3. Then press the Save key to save the changes.
- 22 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
3.7 Call Forward
User can set the static forward to transfer all the incoming calls to specified number;
Also user can use dynamic forward to transfer all the incoming calls forward to the
number inputted when the phone is ringing.
Forward: Enable call forward feature; Options are as follows:
z
Always Forward: All the incoming calls will be transferred unconditionally to
specified number.
z
Busy Forward: The incoming calls will be transferred to specified number when
the phone is busy.
z
No Answer Forward: The incoming calls will be transferred to the specified
number when the ring tone is time out without answer.
To configure Call Forward via Phone interface:
1. Press Menu -->Features-->Call Forward-->Enter, or just press FWD key to enter
Call Forward interface.
2. There are 3 options: Always, Busy, and No Answer.
3. If user chooses one of them, enter the phone number user wants to forward to the
receiving party. Press Save to save the changes.
3.8 Call Transfer
User can use the following two ways to transfer call to the other party:
z
Blind Transfer: Transfer call directly to the other party without any negotiation.
z
Consultation Transfer: Transfer call to the other person involved after the other
person involved answers the incoming call and with consultation.
3.8.1 Blind Transfer
1. Press the Trans soft key during the talking;
- 23 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
2. Enter the Trans number interface, and then input the number you will transfer to;
3. Press the FWD key or the Trans soft key to transfer the call to the number you
want to transfer to;
4. Return to the Idle automatically ;
Note: The UI will display Hold status interface when the number you want to transfer
to does not exist.
3.8.2 Consultation Transfer
1. Press the Trans soft key to enter the number you want to transfer to during the
talking. Input the number you want to transfer to.
2. Press the OK key on the phone keyboard or the Dial key to make a call.
3. Press the Trans soft key to finish transfer after the other person involved answers
the incoming call and with consultation. You can finish transfer via putting down the
handset or press the Cancel soft key to cancel transfer if you currently use handset
to make or answer a call.
3.9 Three-way conference call
User can use the Local conference feature to hold a 3-way conference by pressing
the Conference soft key to invite the current talking line and the line on hold to
attend the conference. The Local conference feature of IP phone VIP-1010PT can
invite two parties at most to attend conference. The conference type of IP phone
VIP-1010PT is Local conference with default.
1. Create talking with first party.
2. Press the New soft key to create a new talking.
3. Press the Back soft key of dial interface to hold talking with first party.
4. Input the number of the second party and press the OK key on the phone
keyboard or the Dial key or the Send soft key to make a call. When the
- 24 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
second party answers your call, inquire whether they want to attend the
conference.
5. Press the Conference soft key to start the 3-way conference.
6. Press the Split soft key to split to two lines standalone talking, then these two
parties talking are under Hold status.
7. Press the Resume soft key to resume the current talking.
8. Press the Cancel soft key or the
key to cancel the conference talking
and return to Idle.
3.10 Call Park
User can use Call Park feature to park the current talking, and then resume the
Parking talking with another phone (For example, with another phone of another
office or conference). Press the Call Park key to park the current talking during
the talking. If successful, you will hear voice announce or see the reserved
extension number on the phone LCD. Dial the reserved extension number in
another phone to resume the Parking talking.
Not all servers can support Call Park feature.
To configure Call Park via Phone interface:
PATH: Press Menu-->Features-->Call Park-->Press Left or Right key or Switch
soft key to enable Call Park--> Press the Down key to set Target
number-->Press the Down key to set Account-->Press the Save soft key to save
3.11 Pickup
User can use pickup to answer other users’ incoming call. The VIP-1010PT IP phone
- 25 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
supports specified pickup and group pickup.
Press the group pickup only to answer line 1 (incoming call) if there are
many lines (incoming calls) in group.
3.11.1 Specified Pickup
Specified pickup can answer specified user’s incoming calls
1. Set specified pickup key via phone interface,
PATH: Press Menu-->Features-->Programmable keys-->Soft
Keys-->PickUp-->Press Down key to set label/Value--> Save soft key.
2. Use specified pickup feature
When the user of specified pickup number is off or busy, you can press the Pickup
key to answer incoming call.
3.11.2 Group Pickup
Group pickup can answer group’s user incoming calls. Group pickup needs to set
group members.
Set group pickup via phone interface
PATH: Press Menu-->Features-->Programmable keys-->Soft Keys-->Group PickUp
-->Press Down key to set label/Value/Account--> Save soft key.
Use group pickup feature
When anyone in group receives an incoming call, you can press the group Pickup key
to answer.
3.12 Speed Dial
User can use the Speed Dial feature to dial the specified contact speedily
PATH: Press Menu-->Features-->Programmable keys-->Soft Keys-->Speed Dial
-->Press Down key to set label/Value/Account--> Save soft key
- 26 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
3.13 Auto-redial
When hung up by the other party during calling, the phone will enter the
auto-redial screen. Press OK for redial now or wait for the timeout to cancel
Auto-redial.
To configure Auto Redial via Phone interface:
1. Press Menu -->Features-->Auto Redial-->Enter.
2. Use the Left or Right key to activate or deactivate Auto Redial.
3. Use the Up or Down key to configure Interval and Times.
4. Then press the Save key to save the changes.
3.14 Hot line
The Hot line refers to the number you often dial. You can set hot lines in the
phone. The phone will dial the hotline number automatically when you pick up
the handset and press the hand-free or the account key. Also you can set the
timeout of dialing the hotline number, and then the phone will dial the hotline
number automatically after the timeout.
To configure Hot line via Phone interface:
1. Press Menu -->Features-->Hot line-->Enter.
2. Use the Left or Right key to activate or deactivate Hot line.
3. Use the Up or Down key to configure Number and Timeout.
4. Then press the Save key to save the changes.
3.15 Intercom
To configure Intercom via Phone interface:
PATH: Press Menu-->Features-->Programmable keys-->Soft keys-->Intercom-->
Press Down key to set label/Value/Account--> Save soft key
1.
Press the Intercom key when the phone is available. The phone will connect the
- 27 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
extension number of remote user automatically.
2.
Press the Intercom key or the Back soft key to end the intercom.
3.
Answer the intercom incoming call.
4.
By default, the IP phone VIP-1010PT will answer the intercom incoming call
automatically and make a noise. You can set the phone to enable the silent
mode when picking up the intercom call so that the other will not hear you.
The features of intercom:
3.16 HotDesking
In some working place, the people are always walking around. HotDesking
feature will make the staff login his account on any computer in the company. In
some public places, the working people are not fixed in one place. Anyone can
use HotDesking for logging his account, and setting the phones to the familiar
mode, such as the remote function of the computer.
3.16.1 Set the HotDesking Key
To configure Intercom via Phone interface:
PATH: Press Menu-->Features-->Programmable keys-->Soft
keys-->HotDesking--> Press Down key to set label--> Save soft key
3.16.2 HotDesking Feature:
1.
After setting the HotDesking on Soft-key, it will return to the idle screen.
2.
Press the HotDesking, and enter the HotDesking screen.
3.
If you press clear on the screen, the phone will begin to clear the information
stored on the phone.
- 28 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
4.
After clearing the setting, the phone will enter the account setting screen.
5.
After entering the account information, it will go back to the home screen, and
begin to use the new account.
3.17 Application
3.17.1
Text Message
The VIP-1010PT IP Phone can send and answer text message. The phone will make
a “Du” sound and present “N piece of new message” on the LCD (For example, 1 new
message), and a twinkling message icon will appear.
Note: Not all servers support message feature.
Read Text Message
1. Access Menu->Message->Text Message-> In box.
2. Press the OK key on the phone keyboard or the Enter soft key to enter the Text
Message interface. Press the OK key on the phone keyboard or the Enter soft
key to enter the in-box interface.
3. Select the message you want to read and press the OK key on the phone
keyboard or the Enter soft key to read.
Send Text Message
1. In the Idle, press the Menu soft key.
2. In the mail menu interface, press the Down key on the phone keyboard to select
Message. Press the OK key on the phone keyboard or the Enter soft key to enter
Message interface.
- 29 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
3. In the Text Message interface, select “New Message”. Press the OK key on the
phone keyboard or the Enter soft key to enter new message and edit it. Press the
“abc” soft key to switch the input methods.
4. Press the OK key on the phone keyboard or the Send soft key to send message;
5. Press the Left or Right key on the phone keyboard or the Switch soft key to switch
to the relevant addresser.
6.
Input the number of addresser:
7.
Press the Send soft key to send message.
Delete Text Message
1. In the Idle, press the Menu soft key.
2. Press the main menu interface. Press the Down key on the phone keyboard to
select message. Press the OK key on the phone keyboard or the Enter soft key
to enter the Message interface.
3. In the Text Message interface, press the Down key on the phone keyboard to
select in-box.
4. Press the OK key on the phone keyboard or the Enter soft key to enter the in-box
interface.
5. Select the message you want to delete and press the Delete soft key .
6. Delete all the text messages in the in-box. Press the Delete soft key and select
“Delete All”. Press the OK soft key and then all the messages in the in-box will
be deleted.
- 30 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
3.17.2 Voice Message
The VIP-1010PT IP Phone can send or answer voice message. The phone will make
a “Du Du” sound, the LED light of message flashes green, and the LCD presents
“New Voice Message” on the LCD with a twinkling voice message icon.
Note: Not all servers support voice message.
Voice Message
You can leave a message when the user whom you called is busy or unavailable.
Leave a message according to the voice prompt of server, and then hang up after
leaving the message.
Set Visit account number of voice message via phone interface.
1. In the Idle, press the Menu soft key.
2. In the Idle, press the Down key on the phone keyboard to select message, press
the OK key on the phone keyboard or the Enter soft key to enter the Message
interface.
3. In the Message interface, press the Down key on the phone keyboard to select the
voice message. Press the OK key on the phone keyboard or the Enter soft key
to enter the Voice Message interface.
4. Select the Voice Message Setting.
5. Press the OK key on the phone keyboard or the Enter soft key to set account 1,
input the Visit account number of voice message ( For example, *97). Press 123
soft key to switch the input methods.
6. Press the OK key on the phone keyboard or the Save soft key to save and return
to message interface.
- 31 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Check voice message
1. Press the Message key or the Connect soft key to call the Visit account number of
voice message.
2. Check voice message according to voice prompt.
z
Set the Visit account number of voice message first before checking voice
message. The LED light of Message will darken after all the voice messages
are checked.
3. Check voice message via phone interface
z
Access Menu-> Message->Voice Message-> New Message. The LCD
displays new messages and old messages of every account.
z
2. Select the account you will check and press the Connect soft key to check
voice message.
- 32 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
4 LCD Advanced Settings
4.1 Basic Settings
4.1.1 Language
You can change the language through the method below:
Press Menu -> Settings -> Basic Setting -> Language
4.1.2 Date & Time
1. The IP phone displays Time and Date in Idle status. You can set the Time and
Date obtained from SNTP server automatically or you can set the time and
date manually.
2. Set SNTP via phone interface: Access Menu -> Settings -> Basic Setting ->
Date & Time -> SNTP Setting.
3. To set the date & time format via the phone interface, access Menu ->
Settings -> Basic Setting -> Date & Time -> Format Setting:
z
Access the Time Format in Format Setting interface and then press the Left
or Right key on the phone keyboard, or the Switch soft key to select the time
format (12 Hours or 24 Hours).
z
In the Date &Time Format interface, press the Up or Down key on the phone
keyboard to access the Date Format. Press the Left or Right key on the
phone keyboard or the Switch soft key to select the date format to process
setting.
z
The phone supports four Date formats. The selected date format will appear
in the Idle. For example, if the time was “2013-09-13”, the date formats in
the menu and the corresponding formats displayed in the Idle would be as
follows:
- 33 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
4.1.3 Backlight
Set the screen backlight level and duration of backlight
Press Menu -> Settings -> Basic Setting ->Backlight
4.1.4 Password Setting
This function is to set into the advanced Settings password
Press Menu -> Settings -> Advanced Setting ->Password Setting
A dialog box “Enter Password:” appears, enter the password: admin (default)
and then press the OK key on the phone keyboard. Input the current password
and the new password, and then confirm the new password to modify the
current password.
4.2 Sound Settings
4.2.1 Phone Volume
1. The Volume key can be used to adjust the volume of handset, hand-free or
headset during a call. Also, the key can be used to adjust the ring tone volume
in the Idle mode.
2. Adjust the volume via the phone interface; access Menu -> Settings -> Basic
Setting -> Phone Volume. In the Volume Setting interface, access the Handset
Volume, Hands-free Volume or Headset Volume interface and then press the “+”
or “-” soft key, or Left or Right key to adjust the volume. Press the Save soft key
- 34 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
to save the operation or press the Back soft key to cancel operation.
4.2.2 Ring Tones
1. The Ring Tone refers to the incoming ring tone, which reminds the user that
a new call is coming with the phone. The VIP-1010PT supports phone ring
tone to distinguish the incoming call from the other surrounding phone’s ring
tone. At the same time, the VIP-1010PT also supports setting of a specific
incoming ring tone for contacts.
2. To set the ring tone via the phone interface, access Menu -> Settings -> Basic
Setting -> Ring Tones.
4.3 Phone Book
4.3.1 Local Phone Book
The Local Phone Book is used for storing the contact names and numbers. The
VIP-1010PT can store up to 500 entries. You can add, edit, delete, search, or call
any contact from the Local Phone Book。
4.3.2 Add contacts manually
Add contacts manually from the Local phone book via Phone interface:
Press Phone book -> Local phone book -> Add to Contacts.
Select the relevant group ( For example, contacts) and press the OK key on the
phone keyboard or the Enter soft key in the UI to enter all Contacts:
1. Press the Add soft key to enter the Add Contact interface.
2. Input name in the relevant area.
3. Press the Down key on the phone keyboard to input the office number in the
relevant area.
4. Press the Down key on the phone keyboard to input mobile number in the
relevant area.
5. Press the Down key on the phone keyboard to input other numbers in the
relevant area.
- 35 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
6. Press the Down key on the phone keyboard to enter Account selection; Press
the Left or Right key on the phone keyboard or the Switch soft key to select
the relevant account. If Auto selected, the phone will select the current
available account automatically when the contact called from Local phone
book.
4.3.3 Add Contacts from All Calls History:
Add contacts from All Calls History in the phone interface:
1. Press the History soft key.
2. Press the Up or Down key on the phone keyboard to select the contact you
want to add.
3. Press the Option soft key to add to contacts.
4.3.4 Search Contacts
1. Press the Book soft key in the Idle interface to enter the Phone Book menu.
2. Select the Local Phone Book and press the OK key on the phone keyboard or
the Enter soft key to enter the Local Phone Book.
3. Press the Search soft key to search contacts.
4. Input keywords such as name, any character of number or whole phone
number and press the Search soft key or the OK key to enter the Search
Contacts interface.
4.3.5 Blacklists
100 Blacklist contacts are available with the VIP-1010PT IP Phone. You can add,
edit, delete, search or call contact. The phone will reject to answer automatically
within the blacklist contacts’ incoming call.
PATH: Press Phone book -> Blacklist -> Add.
4.3.6 Remote Phone Book
1. Access the remote phone book, add the contacts to the local phone book from
the remote phone book or make calls from the remote phone book. Five URLs of
remote phone book are available to set.
2. Set the remote phone book via web interface.
3. Access Book-> Remote Phone Book.
4. Input URL of phone book.
- 36 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5. Input the phone book name.
6. Click the Submit soft key to submit.
7. Access the remote phone book via phone interface.
8. Access Book->Remote phone book.
9. Select the relevant Remote Group and press the Enter soft key. The phone will
load the remote group information, and the LCD will display the contacts of this
remote group.
10. Press the
key or the Back soft key to unlink.
11. Press the Book soft key to enter the Phone Book Menu.
4.4 History Management
The History management of the VIP-1010PT contains dialed calls, received calls,
missed calls and forwarded calls, and supports 100 storage logs at most. You
can check the history, make calls from the calls history and delete the calls
history.
1.
2.
3.
z
z
z
z
Press the History key and the LCD will display all the recent calls.
Press the Left or Right key on the phone keyboard to switch the lists of All
Calls, Dialed Calls, Received Calls, Missed Calls and Forwarded Calls.
Press the Up or Down key on the phone keyboard to select the log.
Press the Option soft key and select the detail. The LCD will display the
detailed information of this log; Press the Dial soft key to make a call from
the History.
Press the Option soft key to add to contacts(Move to Blacklists ) from the
History.
Press the Delete soft key to delete calls log from the History.
Press the Option soft key to select “Delete all” to delete all the calls log from
the History.
4.5 System Customizations
4.5.1 Programmable keys
1. Press the Menu soft key in the Idle interface and access Menu->Features->
Programmable keys.
2. Select the programmable key you will set and press the Enter soft key.
- 37 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
3. Select key style in the type area.
4. Input suitable value in the label area.
5. (Optional) Select the relevant account in the account ID area.
6. (Optional) Input suitable value in Value blank.
7. Press the Save soft key to save or the Cancel soft key to cancel.
4.5.2 SIP Account management
4.5.2.1 Register an Account
Register an account via phone interface:
1. Press the Menu soft key to enter setting interface to select Advanced setting,
and input password(password: admin) to enter the Account setting.
2. Press Enter key to enter the account activation status area.
3. Input the label, display name, register name, account, password and SIP
separately.
4. Press the Save soft key to save, or the Back soft key to cancel.
4.5.2.2 Disable an Account
1. Access Menu->Settings->Advanced setting->Account (password: admin).
2. Press Enter key to enter the account activation status area.
3. Select “Disable” in the account active status area.
4. Press the Save soft key to save or the Back soft key to cancel.
4.6 Basic Network Settings
Through the Basic Network setting, you can set the IP phones to get the IP
address by three ways:DHCP, static IP and PPPoE.
PATH: Menu -> Settings -> Advanced Setting -> Network
4.6.1 DHCP Mode
1. In the Network Settings interface, Press the OK key on the phone keyboard or
the Enter soft key to enter LAN Port.
2. In the LAN Port interface, press the Up or Down key on the phone keyboard to
select DHCP (default is DHCP).
3. Press the Enter on the soft key or the OK key on the phone keyboard to enter
the DHCP switch interface. It will automatically return to the last interface after
seconds.
- 38 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
4.6.2 Static IP Mode
1. In the LAN Port interface, press the Up or Down key on the phone keyboard to
select Static IP and then press the OK key on the phone keyboard or the Enter
soft key to enter Static IP Setting interface and input IP address.
2. Press the Down key on the phone keyboard to enter the Subnet Mask of Static
IP Setting and input the subnet mask.
3. Input the IP address, Subnet mask, Gateway, DNS 1 and DNS 2 in the
corresponding area and press the OK key on the phone keyboard or the Save
soft key to save.
4.6.3 PPPoE Mode
1. In the LAN Port interface, press the Up or Down key on the phone keyboard to
select PPPoE and then press the OK key on the phone keyboard or the Enter soft
key to enter PPPoE Setting interface.
2. Press the Up or Down key on the phone keyboard to enter User Name and
Password.
3. In the related fields, input User Name and Password.
4.7 Reset to Factory
In the Advanced Setting interface, press the Up or Down key on the phone
keyboard to select “Reset to factory”. Press the OK key on the phone keyboard
or the Enter soft key to access the reset to factory interface.
4.8 Reboot
This is a function to set the phone reboot.
1. In the Advanced Setting interface, press the Up or Down key on the phone
keyboard to select Reboot.
2. Press the OK key or the Enter soft key to on the phone keyboard to enter the
reboot warning interface.
- 39 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5 Web Configuration
5.1 Ways to configure
The VIP-1010PT has two different ways for different users.
z
Use phone keypad.
z
Use web browser (recommended way).
5.2 Setting via web browser
When this phone and PC are connected to network, enter the IP address of the WAN
port in this phone as the URL (e.g. http://xxx.xxx.xxx.xxx/ or
http://xxx.xxx.xxx.xxx:xxxx/).
If user does not know the IP address, he can look it up on the phone’s display by
pressing the Status button.
The login page is shown below: A
z
Default user with root level:
‹
User Name: admin
‹
Password: 123
The default password of phone screen menu is 123.
After user configures the IP phone, he needs to click the Save button in the
configuration under Maintenance on the left side of the screen to save user
configuration. Otherwise, the phone will lose user modification after power is off and
on.
- 40 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.3 Status / Basic
Status->Basic page is used to display some basic information for IP phone. Please
refer to the corresponding page for any further information.
Status
Field Name
Explanation
Product
To display the device’s information, such as Model name,
Information
MAC address (IP device’s physical address), Firmware
version and Hardware firmware.
Network
To display the device’s Networking status(LAN Port), such
Information
as Port Type(which could be DHCP/Static/PPPoE), Link
Status, IP Address, Subnet Mask, Gateway, Primary DNS
server, Secondary DNS server, and Primary NTP server
and Secondary NTP server (NTP server is used to
synchronize time from Internet automatically.).
Account
To display device’s Account information and Registration
Information
status (account user name, registered server’s address,
and register result).
- 41 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.4 Account / Basic
Field Name
Explanation
SIP Account
To display and configure the specific Account settings.
Status: To display register result.
Display Label: Label is displayed on the phone’s LCD
screen.
Display Name: Name is sent to the other call party for
displaying.
Register Name: Allocated by SIP server provider, used for
authentication.
User Name: Allocated by your SIP server provider, used
for authentication.
Password: Used for authorization.
SIP Server 1
To display and configure Primary SIP server settings.
Server IP: SIP server address; it could be an URL or IP
address.
Registration Period: The registration will expire after
registration
period.
The
IP
phone
will
re-register
automatically within registration period.
SIP Server 2
To display and configure Secondary SIP server settings.
- 42 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
This is for redundancy; if registering to Primary SIP server
fails, the IP phone will go to Secondary SIP server for
registration.
Secondary SIP server is used for redundancy;
it can be left blank if there is no redundancy
SIP server in user’s environment.
Outbound
Proxy
Server
To display and configure Outbound Proxy server settings.
An outbound proxy server is used to receive all initiating
request messages and route them to the designated SIP
server.
If configured, all SIP request messages from
the IP phone will be sent to the outbound
proxy server forcefully.
Transport Type
To display and configure Transport type for SIP message
UDP: UDP is an unreliable but very efficient transport
layer protocol.
TCP: Reliable but less-efficient transport layer protocol.
TLS: Secured and Reliable transport layer protocol.
DNS-SRV: A DNS RR for specifying the location of
services.
NAT
To display and configure NAT (Net Address Translator)
settings.
STUN: Short for Simple Traversal of UDP over NATS, a
solution to solving NAT issues; by default, NAT is disabled.
- 43 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.5 Account->Advanced
- 44 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Field Name
Explanation
Codecs
To display and configure available/unavailable codecs list.
Codec means coder-decoder which is used to transfer
analog signal to digital signal or vice versa.
Familiar codecs are G723_53, G723_63, G726_32,
PCMA, PCMU,G.729 and G722.
Subscribe
To display and configure MWI, subscription settings.
MWI: Message Waiting Indicator which is used to indicate
whether there is unread new voice messages.
DTMF
To display and configure DTMF settings.
Type:
Supports
Inband,
Info,
RFC2833
or
their
combination.
How To Notify DTMF: Only available when it is DTMF tone
information.
DTMF Payload: To configure payload type for DTMF.
By default, DTMF type is RFC2833 which is the
standard. Inband type uses inband frequency
to indicate DTMF tone which is most used to be
compatible with the traditional telephone
server. Info type uses SIP Info message to
indicate DTMF message.
Call
To display and configure call-related features.
Max Local SIP Port: To configure maximum local sip port
for designated account.
Min Local SIP Port: To configure minimum local sip port
for designated account.
Caller ID Header: To configure which Caller ID format to
fetch for displaying on Phone UI.
Auto Answer: If enabled, IP phone will be auto-answered
when there is an incoming call for designated account.
Provisioning Response ACK: 100% reliability for all
provisional messages, meaning it will send ACK every
time the IP phone receives a provisional SIP message
from SIP server.
User=phone: If enabled, IP phone will send user=phone
within SIP message.
PTime: Interval time between two consecutive RTP
packets.
Anonymous Call: If enabled, all outgoing calls for the
designated account will be anonymous numbers.
Anonymous Call Rejection: If enabled, all incoming
anonymous calls for the designated account will be
rejected.
- 45 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Music
Server
Address
To display or configure third-party MOH (music-on-hold)
server.
Active: To enable or disable this MOH server. If enabled,
the IP phone will play MOH from configured server.
Music Server Address: To configure MOH server address.
Session Timer
To display or configure session timer settings.
Active: To enable or disable this feature. If enabled, the
ongoing call will be disconnected automatically once the
session expired unless it’s been refreshed by UAC or UAS.
Session Expire: Configure session expiry time.
Session Refresher: To configure who should respond for
refreshing a session.
UAC means User Agent Client and here stands
for IP phone. UAS means User Agent Server
and here stands for SIP server.
Broadsoft
To display or configure Broadsoft AOC feature.
AOC: A feature is used to be accounted on Broadsoft
platform.
Please consult your administrator or Planet Technical
support for further information.
Encryption
To enable or disable SRTP feature.
Voice Encryption (SRTP): If enabled, all audio signals
(technically speaking it’s RTP streams) will be encrypted
for more security.
NAT
To display NAT-related settings.
UDP keepalive message: If enabled, IP phone will send
UDP keepalive message periodically to router to keep NAT
port alive.
UDP Alive Msg Interval: Keepalive message interval.
Rport: Remote Port; if enabled, it will add Remote Port
into outgoing SIP message for designated account.
- 46 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.6 Network / Basic
LANGUAGE
Field Name
Explanation
LAN Port
To display and configure LAN Port settings.
DHCP: If selected, IP phone will get IP address, Subnet
Mask, Default Gateway and DNS server address from
DHCP server automatically.
Static IP: If selected, you have to set IP address, Subnet
Mask, Default Gateway and DNS server manually.
PPPoE: Use PPPoE username/password to connect to
PPPoE server.
- 47 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.7 Network / Advanced
Network Configuration
Field Name
Explanation
Local RTP
To display and configure Local RTP settings.
Max. RTP Port: Determine the maximum port that RTP
stream can use.
Min. RTP Port: Determine the minimum port that RTP
stream can use.
SNMP
To display and configure SNMP settings.
Active: To enable or disable SNMP feature.
Port: To configure SNMP server’s port.
Trusted IP: To configure allowed SNMP server address, it
could be an IP address or any valid URL domain name.
SNMP (Simple Network Management Protocols) is
Internet-standard protocol for managing devices on IP
- 48 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
networks.
TR069
To display and configure TR069 settings.
Active: To enable or disable TR069 feature.
Version: To select supported TR069 version (version 1.0
or 1.1).
ACS/CPE: ACS is short for Auto configuration servers as
server side. CPE is short for Customer-premise equipment
as client-side devices.
URL: To configure URL address for ACS or CPE.
User Name: To configure username for ACS or CPE.
Password: To configure Password for ACS or CPE.
Periodic Inform: To enable periodically inform.
Periodic Interval: To configure interval for periodic inform.
TR-069(Technical Report 069) is a technical
specification entitled CPE WAN Management
Protocol (CWMP).It defines an application
layer protocol for remote management of
end-user devices.
DDNS
The VIP-1010PT supports Planet DDNS and Easy DDNS
function.
For now, the VIP-1010PT can only support Planet DDNS.
- 49 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.8 Phone/Time/Language
Time / Language Configuration
Field Name
Explanation
Web Language
To switch to designated language.
Format Setting
To configure time display settings.
Time Format: Determine what format to display on Phone
UI (12 hour/24 hour).
Date Format: Determine what format to display on Phone
UI for Date.
Display Mode: Determine what mode to display Time &
- 50 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Date on Phone UI.
Type
To select how to configure time. It could be set manually
or get from Internet automatically via NTP server.
Manual: To set Time and Date manually.
Auto: To get Time via NTP server.
If user sets time to be Manually, it will only
take effect till the next reboot; after reboot,
the phone will switch to Auto mode
automatically because there is no way for IP
phone to record time during power off.
NTP
To configure NTP server related settings.
Time Zone: To select local Time Zone for NTP server.
Primary Server: To configure primary NTP server address.
Secondary Server: To configure secondary NTP server
address; it takes effect if primary NTP server is
unreachable.
Update Interval: To configure interval between two
consecutive NTP requests.
Network Time Protocol (NTP) is used to
automatically synchronize local time with
Internet time, since NTP server only responds
to GMT time, so that you need to specify the
Time Zone for IP phone to decide the local
time.
Daylight Saving
Time
To display or configure DST settings.
DST is short for daylight saving time, which
means the time on the summer days when the
sun rises early will be adjusted forward to save
daylight. The DST will take effect during the
period that is set by user. (All the settings for
DST are all self-explanatory. Please consult
with your administrator for local DST details.)
- 51 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.9 Phone / Preference
Preference Configuration
Field Name
Explanation
Headset Mode
To enable or disable Headset Mode.
Active: If enabled, the default audio track will be headset
mode; if audio track is changed during a call, it will be
back to headset mode after you hang up the call.
Key Press Sound
To configure the sound volume for key press.
Volume: The valid volume range is from 0 to15; by
default, it’s 8.
- 52 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.10 Phone / Call Feature
- 53 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Call Feature Configuration
Field Name
Explanation
Forward Transfer
To display and configure Forward setting.
There are three types of forward: Always
Forward, Busy Forward and No Answer Forward.
Always Forward: Any incoming call will be
forwarded in any situation.
Busy Forward: An incoming call will be
forwarded if IP phone is busy.
Call Waiting
To enable or disable Call Waiting.
Call Waiting Enable: If enabled, it allows IP phones to
receive a new incoming call when there is already an
active call.
Auto Redial
Auto redial allows IP phones to redial an unsuccessful call
for designated times within designated interval.
Auto Redial: To enable or disable auto redial feature.
Auto Redial Interval: Determine the interval between two
consecutive attempts.
Auto Redial Times: Determine how many times to redial.
DND
DND (Do Not Disturb) allows IP phones to ignore any
incoming calls.
Return Code when DND: Determine what response code
should be sent back to server when there is an incoming
call if DND is on.
DND on Code: The Code is used to turn on DND on
server’s side; if configured, IP phone will send a SIP
message to server to turn on DND on server side if you
press DND when DND is off.
DND Off Code: The Code is used to turn off DND on
server’s side; if configured, IP phone will send a SIP
message to server to turn off DND on server side if you
press DND when DND is on.
Call Park
Call park allows users to park a call to a special extension
and then retrieve it via any other phone within the same
system.
Active: To enable or disable call park feature.
Account: To determine which account to take effect.
Target: To configure a designated target extension.
Please consult with your telephony system
administrator for special extension on your
system.
Intercom
Intercom allows user to establish a call directly with the
- 54 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
callee.
Active: To enable or disable Intercom feature.
Intercom Mute: If enabled, once the call established, the
callee will be muted.
Hot Line
Hot Line allows user to call out the defined number
automatically without dialing any number.
Active: To enable or disable Hot Line feature.
Number: The number you want to dial out automatically.
Delay Time: The delay time before calling out.
Remote Control
Remote Control allows specific host to interact with IP
phone by sending HTTP or HTTPS request. The specific
action could be answering an incoming call, hang up an
ongoing call and so on.
Allowed Access IP List: To configure the allowed host
address.
For now, IP phone can only support IP address,
IP address list and IP address pattern as
allowed hosts
Key As Send
Key As Send allows you to disable send key or assign
pound key as send key.
Others
Return Code When Refuse: Allows user to assign specific
code as returned code to SIP server when an incoming
call is rejected.
Auto Answer Delay: To configure delay time before an
incoming call is automatically answered.
- 55 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.11 Phone / Voice
Voice Configuration
Field Name
Explanation
Echo Canceller
Echo Canceller: To remove acoustic echo from a voice
communication in order to improve the voice quality.
VAD (Voice Activity Detection): Allows IP phone to detect
the presence or absence of human speech during a call.
When detecting period of “silence”, VAD replaces that
silence efficiently with special packets that indicate
silence is occurring. It can facilitate speech processing,
and deactivate some processes during non-speech
section of an audio session. It can avoid unnecessary
coding or transmission of silent packets in VoIP
applications, saving on computation and network
bandwidth.
CNG (Comfort Noise Generation): Allows IP phone to
generate comfortable background noise for voice
communications during periods of silence in a
conversation. It is a part of the silence suppression or
VAD handling for VoIP technology. CNG, in conjunction
with VAD algorithms, quickly responds when periods of
silence occur and inserts artificial noise until voice activity
resumes. The insertion of artificial noise gives the illusion
of a constant transmission stream, so that background
- 56 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
sound is consistent throughout the call and the listener
does not think the line has released.
Jitter Buffer
Jitter buffer is a shared data area where voice packets can
be collected, stored, and sent to the voice processor in
even intervals. Jitter is a term indicating variations in
packet arrival time, which can occur because of network
congestion, timing drift or route changes. The jitter
buffer, located at the receiving end of the voice
connection, intentionally delays the arriving packets so
that the end user experiences a clear connection with
very little sound distortion.
IP phones support two types of jitter buffers: fixed and
adaptive.
Fixed: Add the fixed delay to voice packets. You can
configure the delay time for the static jitter buffer on IP
phones.
Adaptive: Capable of adapting the changes in the
network's delay. The range of the delay time for the
dynamic jitter buffer added to packets can be also
configured on IP phones.
Mic Volume
To configure Microphone volume for headset, handset or
speaker mode.
- 57 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.12 Phone/Key/Display
TIME & DATE
Field Name
Explanation
Soft Key
Allows user to assign specific feature to the designated
soft keys.
For softkey, the available features list:
DND, Menu, MSG, Status, Book, Fwd, PickUp, Group,
PickUp, Intercom, Speed Dial, History, Favorites, Redial,
CallReturn and HotDesking.
Function Key
Allows user to assign specific feature to the designated
function keys.
For function keys, the available features list:
N/A, DND, Menu, MSG, Status, Book, Fwd, PickUp, Group
PickUp, Intercom, Speed Dial, History, Favorites, Redial,
CallReturn and HotDesking.
Others
Backlight Intensity: To adjust the backlight intensity of
Phone UI.
Backlight Time: To adjust backlight on timer; once
expired, the backlight of Phone UI will go off.
- 58 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.13 Phone / Ring Tones
Ring Tone Configuration
Field Name
All Ringtones
Explanation
Allows user to upload and view ringtone files or delete
uploaded ringtone files.
Ringtone files must be .wav format and
has some specific requirements. Please
contact Planet technical support team for
instructions on how to make ringtone files.
Distinctive Ringers
Distinctive ringers allow different incoming calls to
trigger distinctive ringtones. The IP phone will check
"Alert-Info" header inside the incoming “invite” SIP
message. And strip out the URL or keyword inside the
“Alert-Info” header, from the specific URL or keyword
to match or download designated ringtones to play.
- 59 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.14 Phone / Tones
IAX2 Configuration
Field Name
Explanation
Tone
Allows user to select a specialized tone sets (classified by
countries) or to customize own tones.
Available country tone sets are:
China, Spain, Luxembourg, Sweden,
Taiwan, Belgium, Denmark, Finland,
Germany, Netherlands, Norway and
Portugal.
- 60 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.15 Phone / Dial Plan
Dial Plan
Field Name
Explanation
Replace rule
Rules
Allow user to select Replace rule or Dial-now to display
or edit.
- 61 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Rules Modified
Allow user to modify selected rules information To
replace rules, you can modify related account, prefix
and replacement.
Area Code
Area codes are also known as NPAs (Numbering Plan
Areas). They usually indicate different geographical
areas within one country. If entered numbers match
the predefined area code rule, the IP phone will
automatically prefix outgoing number with area code.
There is only one area code rule
supported.
Dial Now
Rules
Allow user to select Replace rule or Dial-now to display
or edit.
Dial Now Delay
Allow user to configure dial now delay time for dial
now. It means user can configure the IP phone to dial
out the phone number automatically after the
designated delay time if it matches any dial now rule.
Rules Modify
Allow user to modify selected rules information, for
dial-now rule, user can modify related account, Dial
now Rule itself.
Area Code
Area codes are also known as NPAs (Numbering Plan
Areas). They usually indicate different geographical
areas within one country. If entered numbers match
the predefined area code rule, the IP phone will
automatically prefix outgoing number with area code.
There is only one area code rule
supported.
- 62 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.16 Phone –>Action URL
DIAL PEER
Field Name
Explanation
Action URL
To display and configure Action URL settings.
Setup Completed: When the IP phone completes startup.
Registered: When the IP phone successfully registers an
account.
Unregistered: When the IP phone logs off the registered
account.
Register Failed: When the IP phone fails to register an
account.
Off Hook: When the IP phone is off hook.
On Hook: When the IP phone is on hook.
- 63 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Incoming Call: When the IP phone receives an incoming
call.
Outgoing Call: When the IP phone places a call.
Established: When the IP phone establishes a call.
Terminated: When the IP phone terminates a call.
Open DND: When the IP phone enables the DND mode.
Close DND: When the IP phone disables the DND mode.
Open Always Forward: When the IP phone enables the
always forward.
Close Always Forward: When the IP phone disables the
always forward.
Open Busy Forward: When the IP phone enables the busy
forward.
Close Busy Forward: When the IP phone disables the busy
forward.
Open No Answer Forward: When the IP phone enables the
no answer forward.
Close No Answer Forward: When the IP phone disables
the no answer forward
Transfer Call: When the IP phone transfers a call.
Blind Transfer: When the IP phone blind transfers a call.
Attended Transfer: When the IP phone performs the
semi-attended/attended transfer.
Hold: When the IP phone places a call on hold.
UnHold: When the IP phone retrieves a hold call.
Mute: When the IP phone mutes a call.
UnMute: When the IP phone un-mutes a call.
Missed Call: When the IP phone misses a call.
IP Changed: When the IP address of the IP phone
changes.
FWD Incoming Call: When the IP phone forwards an
incoming call.
Reject Incoming Call: When the IP phone rejects an
incoming call.
Answer New Call: When the IP phone answers a new call.
Transfer Finished: When the IP phone completes to
transfer a call.
Transfer Failed: When the IP phone fails to transfer a call.
Idle To Busy: When the state of the IP phone changes
from idle to busy.
Busy To Idle: When the state of phone changes from busy
to idle.
- 64 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.17 Phone Book->Local Phone Book
AUDIO Configuration
Field Name
Explanation
Contact
To display and select local contact type.
All Contacts: To display or edit all local contacts.
Favorites: To display or edit favorite contacts.
Black List: To display black list contacts.
Search
To search designated contacts from local phonebook.
Dial
To dial out a call or hang up an ongoing call from Web UI.
- 65 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
For this feature, you need to have the
remote control privilege to control IP
phone via Web UI. Please refer to section
“Remote Control” on the Web
UI->Phone->Call Feature page.
Group
To display or edit Group contacts.
Group Setting
To display or change Group name, related ringtone or
description.
5.18 Phone Book->Remote Phone Book
FEATURE
Field Name
Explanation
Remote
To display and configure Remote Book settings.
Book
Index: To select desired Remote Book item to display and
configure.
Local Book URL:To configure remote book server address
Local Book Name: To configure display remote book name on Phone
UI
IP phone supports at most 5 remote
books. Please refer to your administrator
or Planet Technical Support team for how
to establish a remote book server and how
to create remote book xml file.
- 66 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.19 Phone Book->Call log
Call Log
Field Name
Explanation
Basic Setting
Call History
To display call history records.
Available call history types are All calls, Dialed calls,
Received calls, Missed calls and Forwarded calls.
HangUp: To click to hang up ongoing call on the IP phone.
For “HangUp” feature, you need to have
the remote control privilege to control IP
phone via Web UI. Please refer to section
“Remote Control” on the Web
UI->Phone->Call Feature page.
- 67 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.20 Phone Book->LDAP
LDAP
Field Name
Explanation
LDAP
To display and configure LDAP phonebook settings.
Name Filter: The settings are used to tell LDAP server
what name attributes to search.
Number Filter: The settings are used to tell LDAP server
what number attributes to search.
Server: To configure LDAP server’s address.
Port: To configure LDAP server’s port.
Base DN: To configure searching base DN on LDAP server.
User Name: To configure user name for accessing LDAP
server.
Password: To configure password for accessing LDAP
server.
Name Attribute: To configure which name attributes
should be feedback from LDAP server.
Number Attribute: To configure which number attributes
should be fedback from LDAP server.
Display Name: To configure display name on Phone UI
when there is any searching result from LDAP server.
Max. Hits: To configure the maximum size of result
response from LDAP server.
Search Delay Time: To configure delay time before
initiating LDAP searching request after you input a value
from Phone UI.
- 68 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.21 Phone Book->BroadSoft
Broadsoft
Field Name
Explanation
Broadsoft PhoneBook
To display and configure Broadsoft PhoneBook settings.
PhoneBook Item: To select specific item to configure.
Display Name: The name displayed on IP phone’s LCD
screen when accessed via Phone UI.
Server Address: Broadsoft PhoneBook server’s
address.
Server Port: Broadsoft PhoneBook server’s port.
User Name: Username used to access Broadsoft
PhoneBook server.
Password: Password used to access Broadsoft
PhoneBook server.
IP phone supports at most 5 Broadsoft
PhoneBook items. For Broadsoft Phone
Book’s server address, port, username and
password, you need to consult your
Broadsoft service provider for further
information.
- 69 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.22 Upgrade->Basic
Upgrade Configuration
Field Name
Explanation
Upgrade
To select upgrading ROM file from local or a remote
server automatically.
Note: Please make sure it’s the right file format for the
right model.
Firmware Version
To display firmware version; firmware version starts
with MODEL name.
For example, VIP-1010PT firmware version should be
like 50.xxx.xxx.xxx.
Hardware Version
To display Hardware version.
Reset to Factory
To enable you to reset IP phone’s setting to factory
Setting
settings.
Reboot
To reboot IP phone remotely from Web UI.
- 70 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.23 Upgrade->Advanced
Upgrade- Advance
Field Name
Explanation
PNP Option
To display and configure PNP setting for Auto
Provisioning.
PNP: Plug and Play; Once PNP is enabled, the phone will
send SIP subscription message to PNP server
automatically to get Auto Provisioning server’s address.
By default, this SIP message is sent to multicast
address 224.0.1.75 (PNP server address by standard).
DHCP Option
To display and configure custom DHCP option.
DHCP option: If configured, IP phone will use
designated DHCP option to get Auto Provisioning
server’s address via DHCP.This setting requires DHCP
server to support the corresponding option.
Manual Update
To display and configure manual update server’s
Server
settings.
URL: Auto provisioning server address.
- 71 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
User name: Configure if server needs a username to
access, otherwise left blank.
Password: Configure if server needs a password to
access, otherwise left blank.
Common AES Key: Used for IP phone to decipher
common Auto Provisioning configuration file (For the
VIP-1010PT, this configuration file is
r000000000053.conf.).
AES Key(MAC):Used for IP phone to decipher
MAC-oriented auto portioning configuration file(for
example, file name could be 00304f888888.conf if IP
phone’s MAC address is 00304f888888.).
Note: AES is one of many encryptions. It should be
configured only if the configure file is ciphered with AES,
otherwise left blank.
AutoP
To display and configure Auto Provisioning mode
settings.
This Auto Provisioning mode is actually
self-explanatory.
For example, mode “Power on” means IP phone will go
to do Provisioning every time it powers on.
System Log
To display syslog level and export syslog file.
Syslog level: From level 0~7. The higher level means
the more specific syslog is saved to a temporary file.
By default, it’s level 3.
Export Log: Click to export temporary syslog file to local
PC.
PCAP
To start, stop packets capturing or to export captured
Packet file.
Start: To start capturing all the packets file sent or
received from IP phone.
Stop: To stop capturing packets.
Note: IP phone will save captured packets file to a
temporary file; this file maximum size is 1M
(megabytes), and will stop capturing once this
maximum size is reached.
Others
To display or configure other features from this page.
Configure file: To export or import configure file for IP
phone.
- 72 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.24 Security->Basic
Upgrade- Advance
Field Name
Explanation
Web Password
To modify user’s password.
Modify
Current Password: The current password you used.
New Password: Input new password you intend to use.
Confirm Password: Repeat the new password.
For now, IP phone can only support user administrator
mode.
- 73 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
5.25 Security->Advanced
Sections
Web Server Certificate
Description
To display or delete Certificate which is used when IP
phone is connected from any incoming HTTPs request.
The default certificate could not be deleted.
Web Server Certificate
To upload a certificate file which will be used as server
Upload
certificate.
Client Certificate
To display or delete Certificates which is used when IP
phone is connecting to any HTTPs server.
Client Certificate
To upload certificate files which is used as client
Upload
certificate.
- 74 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
6 Appendix
6.1 Digit-character Map Table
Keypad
Character
Keypad
1@
Character
7PQRSpqrs
2ABCabc
3DEFdef
8TUVtuv
9WXYZwxyz
4GHIghi
*/.
5JKLjkl
0
6MNOmno
#/SEND
6.2 Frequently Asked Questions List
Q1: No operation after power on?
A1: Check if the power adapter is properly connected.
If applicable, check if the PoE (Power over Ethernet) switch behind the IP phone
is set correctly.
Q2: No dial tone?
A2: Check if the handset cord is properly connected.
Q3: Cannot make a call?
A3: Check the status of User SIP registration status or contact user administrator,
supplier, or ITSP for more information or assistance.
Q4: Cannot receive any phone call?
A4 : Check the status of user SIP registration status, or contact user administrator,
supplier, or ITSP for more information or assistance
Q5: No voice during an active call?
A5: Check if the servers support the current audio codec type, or contact user
administrator, supplier, or ITSP for more information or assistance.
- 75 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
Q6: Cannot connect to the configuration website?
A6: Check if the Ethernet cable is properly connected.
Check if the URL is right; the format of URL is: http:// the Internet port IP address.
Check if user firewall/NAT settings are correct.
Check if the version of IE is IE8, or use other browser such as Firefox or Mozilla, or
contact user administrator, supplier, or ITSP for more information or assistance.
Q7: Forget the password?
A7: Default password of website and menu is null.
If user changes the password and then forget it, or user cannot access to the
configuration website or the menu items need password.
Solution:
Factory default: press the Menu button and choose 16Factory Default and then a
notice will appear. Choose OK by using the corresponding softkey button.
If user chooses the factory default, user will return the phone to the original factory
settings and will erase ALL current settings, including the directory and call logs.
Q9: How to register VIP-1010PT to IPX-2100
A9:
[In IPX-2100]
For extensions, please create a new account and remember their user name and
password.
- 76 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
[In VIP-1010PT]
On Account/ Basic page.
Account Active = Enable
Display Label = Choose any Display message you want.
Display name: Choose any Display name you want.
Register Name: 204 (in this case)
User name : 204 (in this case)
Password: 123456 (in this case)
Server IP: 192.168.1.21
After saving, user can check the register status in “Status” item.
- 77 -
High Definition PoE IP Phone (1-Line)
VIP-1010PT
- 78 -