g
GE Security
NetworX Series
TM
NX-1208E LED keypad
User manual
g
GE Security
TABLE OF CONTENTS
TABLE OF CONTENTS ................................................................................................................................................... 2
INTRODUCTION .............................................................................................................................................................. 3
GLOSSARY OF TERMS................................................................................................................................................... 4
KEYPAD DISPLAY & LED’S ......................................................................................................................................... 5
UNDERSTANDING THE LIGHTS ........................................................................................................................................... 5
EMERGENCY ACTIVATION KEYS ............................................................................................................................. 7
KEYPAD FUNCTIONS ..................................................................................................................................................... 8
ARMING YOUR SYSTEM IN THE “AWAY” MODE ............................................................................................................... 8
MAKING THE SYSTEM READY TO ARM ............................................................................................................................... 8
ARMING YOUR SYSTEM IN THE “STAY” AND “NIGHT” MODES ....................................................................................... 8
USING THE QUICK ARM (OPTIONAL).................................................................................................................................. 9
CHANGING MODES WHILE SYSTEM ARMED ........................................................................................................................ 9
DISARMING THE SYSTEM ................................................................................................................................................... 9
CANCEL / ABORT FEATURE (OPTIONAL) ..................................................................................................................... 10
BYPASSING ZONES ........................................................................................................................................................... 10
GROUP BYPASS ................................................................................................................................................................ 10
UNBYPASSING ................................................................................................................................................................. 10
TURNING THE DOOR CHIME ON AND OFF ....................................................................................................................... 10
ADDING AND CHANGING USER CODES ................................................................................................................. 11
ASSIGNING USER CODE AUTHORITY LEVELS.................................................................................................... 12
OTHER KEYPAD FUNCTIONS.................................................................................................................................... 13
SETTING THE KEYPAD TONE............................................................................................................................................. 13
VIEW ALARM MEMORY .................................................................................................................................................... 13
TEST FUNCTION (OPTIONAL) ............................................................................................................................................ 13
DETECTOR RESET FUNCTION ............................................................................................................................................ 13
SETTING THE SYSTEM CLOCK ........................................................................................................................................... 14
SETTING THE SYSTEM DATE ............................................................................................................................................. 14
SETTING THE KEYPAD LIGHTING ...................................................................................................................................... 14
KEYPAD CONTROL TONES (BEEPS)........................................................................................................................ 15
APPENDIX A – REFERENCE TABLES....................................................................................................................... 16
NX-1208E User manual
Page 2
04/10/04
g
GE Security
INTRODUCTION
This manual is furnished to help you understand your security system and become proficient in its
operation. All users of your security system should read and follow the instructions in this booklet
and, if possible, practice on the keypad control while your professional installer is on site. Failure to
do so could result in the security system not working properly. Please keep this booklet in an
accessible location for the life of the security system. If you do not understand any part of this manual
you should notify your installing company.
The SECURITY CONTROL can be turned on (ARMED) and off (DISARMED) by entering a 4 or 6 digit code
into the Keypad Control, which is similar to a telephone keypad. If your Security Control has been so
programmed, you may be able to turn on (ARM) your System by simply double pressing the [AWAY], [STAY]
or [NIGHT] key. The system must always be disarmed using a 4 or 6 digit code. The LED keypad includes up
to 18 lights and a built-in electronic sounder. These provide specific information relating to the status of the
security system, which is described in the booklet. Understanding what the lights and sounds mean will help
you to easily operate your system.
Keep in mind, the level of security you will obtain with this system relates specifically with two major
factors:
1. The quantity, quality and placement of security devices attached to this system.
2. The knowledge you have of the security system and how that knowledge is utilized in a weekly test of
the complete system.
You should be aware of the following facts when preparing a safety/security plan for your
home/business:
1. Your security system is an electronic device and is subject to failure or malfunction. Do not rely on it
as your single source of security.
2. Your system should be tested weekly.
3. Your system will not work without power.
4. Warning devices will need to be loud enough, wired correctly, and properly placed to provide
notification of an alarm event.
5. Smoke and heat detectors may not detect heat and smoke in all situations.
6. Use qualified security professionals to install and maintain your security system.
7. It may be possible to arm the security system without the backup battery connected. Your periodic
test should be done with AC Power removed to verify the battery is connected and adequately
charged.
8. Care should be taken to plug in and restrain the AC transformer after testing.
Please read the following information and instructions carefully before operating your security control
system.
NX-1208E User manual
Page 3
04/10/04
g
GE Security
GLOSSARY OF TERMS
Abort Delay
Authority Level
Central Station
Chime Feature
Codes
Duress Code
Forced Arming
Function Code
Group Bypass
Instant/Delay
Master Code
Partitioned System
Perimeter
Quick Arm
User Code
NX-1208E User manual
An option that allows a delay in reporting to the central station.
The level of access an individual has when using an alarm panel.
The location where alarm data is sent during an alarm report.
An option that allows the keypad to sound a ding-dong whenever an entry/exit
door is opened.
Can be either User Codes (relating to a person) or Function Codes (a toggle
switch to turn specific functions on/off). NOTE: A system may have either
four-digit codes or six-digit codes, but not a mixture of the two.
An option that allows a special code to be sent to the central station that
indicates the alarm system is being operated under duress.
An option that allows the system to be turned on (ARMED) with one or more
zones open. A system that is ready to be “force armed” will flash the entire
message, “System Not Ready, For Help press º” NOTE: Those zones that
are not ready will not create an alarm.
A Function Code is either a four (4) or six (6) digit code that has been
programmed by the installer to operate a device.
An option that allows the user to bypass multiple zones with a single operation.
An option that allows an instant alarm condition for Entry/Exit doors, or grants a
delay to allow someone to enter/exit the building without an alarm, or before
entering a user code to disarm.
A master arm/disarm code that can program other user codes.
A system divided into multiple areas in which its own user or users control each
area.
The outer edge of the protected area.
An option that allows you to turn on (ARM) the security system by double
pressing either the [AWAY], [STAY], or [NIGHT] key on the keypad (for
ARMING only) as programmed by the installing company.
A four (4) or six (6) digit entry code used to arm or disarm the system.
Page 4
04/10/04
g
GE Security
KEYPAD DISPLAY & LED’S
Understanding the lights
Fire Light
Ready Light
Power Light
Service Light
Buzzer
Zone Lights
Numeric code
entry keys
4 Function
Keys
3 emergency activation keys
Away/Stay/Night Keys
The away, stay, and night keys are “on” when the system is armed to one of these
corresponding modes. The armed, stay, and night keys are “off” when it is disarmed. The
armed, stay, and night keys will flash when there has been an alarm during the previous
arm cycle.
Bypass Key
The bypass key is illuminated when any zone in this keypad’s partition is bypassed. The
zone(s) that is bypassed will also be illuminated. If the bypass key is “off”, no zones are
bypassed.
Abort Light
The abort light will flash during an abort delay time. If a code is entered while this light is
flashing, all abortable reports will stop the communication process. Note: The abort
feature must be enabled. Entering a code during or after an alarm report to the central
station will cause the abort light to come on. It will stay on until the central station has
received the cancel report. Note: The cancel feature must be enabled.
NX-1208E User manual
Page 5
04/10/04
g
GE Security
Chime Light
The chime light is “on” when the chime feature is “on”; “off” otherwise.
Fire Light
A steady fire light means a fire zone has been faulted. A rapidly flashing fire light means
that a fire zone is in a trouble condition.
Power Light
The power light is on if the primary power is on. The power light will flash if the system has
a low battery condition.
Ready Light
The ready light is “on” when the system is ready to arm and “flashes” if ready to force arm.
The ready light is “off” when the system is not ready to arm because of a zone(s) being
faulted.
Service Light
The service light will be “on” if the security system requires service. If the service light is
“on, press the [*] key followed by the [2] key to determine the service condition. One or
more zone lights will illuminate indicating what service(s) is required. Call your service
provider immediately for these problems. Below is a listing of what each digit means in a
service condition.
LIGHT
1
PROBLEM
SYSTEM FAULT - Press the [1] key. The zone light(s) that is
illuminated corresponds to the system fault(s) below:
1
Over Current Fault
5
Expander Low Battery
2
Siren Trouble
6
Expander Box Tamper
3
Box Tamper
7
Expander Trouble
4
Expander Power
8
Ground Fault
Note: Faults 1 & 2 are global in nature and will affect all
partitions of a multi-partition system. Press the [#] key to
return to the 1 of 8 service lights.
ZONE TAMPER - Press the [2] key and the zone light(s) will
2
illuminate showing the zone(s) that are tampered. Press the [#]
key to return to the 1 of 8 service lights.
ZONE LOW BATTERY - Press the [3] key. The zone light(s)
3
will illuminate showing which zone(s) has a low battery. This
only applies to wireless zones. Press the [#] key to return to the
1 of 8 service lights.
ZONE LOSS OF SUPERVISION - Press the [4] key and the
4
zone light(s) will illuminate showing which zone(s) has loss of
supervision. This only applies to wireless zones. Press [#] key
to return to the 1 of 8 service lights.
ZONE TROUBLE - Press the [5] key and the zone light(s) will
5
illuminate showing which zone(s) has a trouble condition.
Press the [#] key to return to the 1 of 8 service lights.
6 N TELEPHONE FAULT - Press the [6] key. The zone light(s) that
is illuminated corresponds to the system fault(s) below:
6 Line Trouble / Line Cut - This light will illuminate when
there is telephone line trouble or the telephone line has
been cut. The service light will remain lit until the
telephone trouble clears and a user code is entered.
7 Auxiliary Comm Device Fail - Backup has failed.
7 N FAILURE TO COMMUNICATE - This light will illuminate when
there is a failure to communicate between your system and the
central station.
8 N LOSS OF SYSTEM TIME - This light will illuminate when there
has been a loss of power and your system clock needs to be
reset.
Press the [#] key to exit the Service Light mode.
EXIT
N Note: This fault is global in nature and will affect all partitions
of a multi-partition system.
NX-1208E User manual
Page 6
04/10/04
g
Zone Light
GE Security
The zone lights are “off” when everything is normal. A zone light will be “on” if the zone has
been bypassed. If a zone light is “flashing”, that zone is in alarm or has been faulted. If a zone
light is “flashing” rapidly, it means that the zone is in a trouble condition. Trouble conditions
are
● Tamper
● Hardware
● Low Battery
● Loss of supervision
(A combination of Alarm/Fault and Tamper/Trouble will produce a rapid “flashing” light for a
short period of time, followed by a slow “flashing” light.)
EMERGENCY ACTIVATION KEYS
NOTES: You must hold these keys for 2 seconds to activate these functions. Your system may not be
programmed for these activation keys. You should press these keys only in an emergency situation that
requires response by emergency personnel. If your system is programmed for these functions, the following
reports can be sent.
Fire Key – This key can activate the fire alarm when pressed for two seconds. If your system is connected to
a monitoring center, an emergency report could be sent to that center.
Auxiliary Emergency Key – This key can activate the auxiliary alarm when pressed for two seconds. If your
system is connected to a monitoring center, an emergency report could be sent to that center.
Police (Panic/Hold-Up) Key - This key can sound a local audible alarm when pressed for two seconds. If
your system is connected to a monitoring center, an emergency report could be transmitted to that center.
NOTE: Some Panic/Hold-Up alarms are programmed to be silent at the protected site while reporting an
alarm to the monitoring center. Check with your installing company to determine how your security system will
respond to the Panic/Hold-Up activation.
NX-1208E User manual
Page 7
04/10/04
g
GE Security
KEYPAD FUNCTIONS
Arming your system in the “AWAY” mode
AWAY is used when the user is away from the premise and wants the interior protected. Listed below are the
steps to arm in the AWAY Mode:
Step 1
Step 2
Close all protected doors and windows.
• Ready light will be on or flashing when all protected zones and sensors are secure.
NOTE: If any zones are bypassed, a sensor in that zone can be violated without
affecting the ready light.
• The security system will not arm if the ready light is not on or flashing.
• If the power light is off, you have no AC power. Restore power if possible. If not, contact your
installing company for service.
• If the power light is flashing, you have a battery failure. Contact your installing company for
service.
Enter your 4 or 6 digit user code to arm the system.
• The away key will illuminate steady. The stay and night keys will flash during the exit delay.
• You may now leave the building.
Making the system ready to arm
If the ready light is not on or if it is flashing, a zone is not secure. To identify this zone check the zone lights.
A zone light will be “on” if the zone has been bypassed. If a zone light is “flashing”, that zone is in alarm or has
been faulted. If a zone light is “flashing” rapidly, it means that the zone is in a trouble condition.
Arming your system in the “STAY” and “NIGHT” modes
STAY is used when the user is inside the premise and wants protection around the perimeter. Listed below
are the steps to arm in the STAY Mode:
Step 1
Step 2
Close all protected doors and windows.
• Ready light must be on or flashing when all protected zones and sensors are secure.
NOTE: If any zones are bypassed, a sensor in that zone can be violated without
affecting the ready light.
• The security system will not arm if the ready light is not on or flashing.
• If the power light is off, you have no AC power. Restore power if possible. If not, contact your
installing company for service.
• If the power light is flashing, you have a battery failure. Contact your installing company for
service.
Enter your 4 or 6 digit user code. (Optional, if programmed.)
If “Auto Bypass” is enabled, all interior zones will be bypassed if you do not leave through a
designated entry/exit door. Omit Step 3.
NX-1208E User manual
Page 8
04/10/04
g
Step 3
•
•
•
GE Security
Press [STAY].
The stay key will illuminate indicating that all interior zones are bypassed. (All interior
devices will bypass automatically, giving the user freedom of movement within the interior
area.) The away and night keys will flash during the exit delay.
The bypass key will illuminate if any zone(s) are bypassed. If any zone(s) have been
bypassed previously by the user, the light(s) corresponding to the bypassed zone(s) will
illuminate, alerting the user that a zone(s) may be unprotected and can be faulted without
an alarm.
Step 4
To toggle between the STAY and NIGHT mode, double press the key corresponding to
the mode you desire.
Step 5
To upgrade from the STAY or NIGHT mode to the AWAY mode, double press [AWAY].
Note: Once the AWAY mode is activated, the system must be disarmed to revert to the
STAY or NIGHT mode.
Using the Quick Arm (optional)
The Quick Arm feature may be used if it is enabled. Quick Arm will allow the user to arm the security system
in the AWAY, STAY, or NIGHT mode by pressing the corresponding key twice. This feature is used for
ARMING ONLY, and will not disarm the security system. This is ideal for a maid or baby sitter, etc.
Changing modes while system armed
Double pressing the [AWAY], [STAY], or [NIGHT] key will change to the corresponding mode. Once the
AWAY mode is entered, the system must be disarmed to change modes.
Disarming the system
When you enter the protected area through one of the designated Entry/Exit doors, the keypad control will
sound a continuous tone for the duration of the entry delay time, or until you enter a valid code. The away,
stay and night keys will go off and the tone will stop. The security system is now DISARMED. If a valid code
is not entered before the end of the entry delay, an alarm will occur. (NOTE: If the away, stay or night keys
are flashing during the entry delay, the alarm system has been activated in your absence. Leave the
building immediately and call your alarm company and/or the police from a safe location.)
NX-1208E User manual
Page 9
04/10/04
g
GE Security
CANCEL / ABORT feature (optional)
The abort light will flash during an abort delay time. If a code is entered while this light is flashing, all
abortable reports will stop the communication process. Entering a code during or after an alarm report to the
central station will cause the abort light to come on. It will stay on until the central station has received the
cancel report.
Bypassing zones
If you wish to bypass one or more zones, this must be done while the system is in the disarmed state. The
following steps are used for bypassing zones:
Step 1 Press the [BYPASS] key.
Step 2
Enter user code, if required (optional). The bypass light flashes.
Step 3
Enter 1 or 2 digits indicating the zone you wish to bypass. (Example: Press the [1] key for zone 1,
press [1] - [2] for zone 12.)
Step 4
Press the [BYPASS] key again.
Step 5
The corresponding zone light will illuminate indicating the zone has been bypassed. Repeat steps 3
and 4 for any other zone(s) that need to be bypassed.
Step 6
Press the [BYPASS] key again -or- press the [#] key to exit the Bypass Mode. The bypass light will
stop flashing upon exiting the Bypass Mode.
Group bypass
By pressing the [BYPASS] key, followed by the [0] key, then the [BYPASS] key again, all zones that are
designated as group bypass zones will be bypassed. Press the [BYPASS] key again to exit group bypassing.
Unbypassing
To manually unbypass zones, perform the bypassing procedure on a zone that is already bypassed. The
corresponding light for that zone will go off when unbypassed.
NOTE: All zones will automatically be unbypassed each time the system is disarmed.
Turning the door chime ON and OFF
The door chime is turned on or off by pressing [r]-[1] while the system is in the disarmed state. If the chime is
“on”, the chime light will be illuminated. If the chime is “off”, the chime light will be off. Each time [r]-[1] is
pressed it will toggle the chime feature on/off and produce a momentary ding-dong sound.
NX-1208E User manual
Page 10
04/10/04
g
GE Security
ADDING AND CHANGING USER CODES
Your system must be Disarmed to add/change user codes.
Step 1
Press [r]-[5].
Step 2
Enter a “Master Arm/Disarm Code”.
NOTE: For partitioned systems, someone changing the code of another person must
have access to all or more partitions than the user being changed.
Step 3
The ready light will flash.
Step 4
Enter the 2 digit (applies to NX4/6/8) or 3 digit (applies to NX8E) “user number” (always enter
2 digit such as [0] - [3] for user 3, or [1] - [0] - [0] for user 100).
Step 5
Enter the new four (4) or six (6) digit “user code”.
NOTE: To delete a user code, enter [r]-[r]-[r]-[r] for a 4-digit code, or [r]-[r]-[r]-[r]-[r]-[r]
for a 6-digit code.
Step 6
The ready light will flash indicating you are back at Step 4 above. If the code is rejected, the
sounder will beep 3 times.
Step 7
If another “user code” needs to be programmed, return to Step 5.
Step 8
Press the [#] key while the ready light is flashing to exit the User Code Programming Mode.
NX-1208E User manual
Page 11
04/10/04
g
GE Security
ASSIGNING USER CODE AUTHORITY LEVELS
Assign authority levels to users by following the steps below. Assign user codes before assigning authority
levels. Your system must be in the disarmed state to change user code authority levels.
Step 1
Press [r]-[6]-[“Master Arm/Disarm Code”].
NOTE: Someone changing the authority of another person can only add or remove
partition authorization for partitions to which they have access.
Step 3
The ready light will flash.
Step 4
Enter the 2-digit (applies to NX4/6/8) or 3-digit (applies to NX8E) user number. Always use
leading zeros when necessary, i.e. "004" for user number 4.
The ready light is constant and the instant light will flash.
Step 5
Lights illuminated indicate the authority levels assigned to this code. An explanation of the
lights is listed below. You may toggle (turn on/off) the authority level by pressing the number
for that authority level.
LIGHT
1
2
3
4
5
6
7
8
AUTHORITY LEVELS IF LIGHT 8 IS OFF
Reserved (Note: Do not change if on.)
Arm Only
Arm Only After Close Window
Master Arm/Disarm (can program other codes)
Arm/Disarm
Bypass Zones
Open / Close Reporting
If this light is on, this code is programmed as a
function code. Do not change, Press [#] - [#] to exit.
Step 6
Press the [r] key. The ready light will flash. This moves you to the partition enable. (The user
has access in partitions that are illuminated.)
Step 7
The illuminated numbers indicate each partition where the user has access. To change any
of the partitions where the user has access, press numbers corresponding to areas where
you want to give the user access or deny access. (Example: If zone light #2 is lit, then the
user is assigned access to partition #2. By pressing the [2] key, the light will go off, denying
access to partition #2. Refer to chart shown below.
LIGHT
1
2
3
4
5
6
7
8
PARTITIONS ASSIGNED
Partition 1
Partition 2
Partition 3
Partition 4
Partition 5
Partition 6
Partition 7
Partition 8
Step 8
When the partitions are assigned, press the [r] key. This returns you to Step 3 previously
mentioned. At this point you may enter another user number to assign authority level.
Repeat Steps 4 - 8 until you have assigned authority levels to all user numbers.
Step 9
Press the [#] key to exit the Assigning Authority Level Program.
NX-1208E User manual
Page 12
04/10/04
g
GE Security
OTHER KEYPAD FUNCTIONS
Setting the keypad tone
Step 1
Press the [r] key.
Step 2
Press the [0] key. Keypad is now in the “Adjust Tone” mode.
Step 3
Pressing the [1] key will make the keypad sounder go to higher tones, pressing the [2] key will
make the keypad sounder go to lower tones.
Step 4
When the desired tone is reached, press the [#] key to set this tone and exit
from the “Adjust Tone” mode.
View alarm memory
Step 1
Press the [r] key.
Step 2
Press the [3] key to display the zone(s) on the keypad that created the last alarm.
Step 3
The ALARM MEMORY feature will flash those zones that created alarms and will light steady
those zones that were bypassed during the last alarm.
Test function (optional)
If programmed, this function will perform a battery test, communicator test, and/or a siren test.
Step 1
Press [r] [4] [4]. The test will be performed as programmed.
Step 2
If the siren test is performed, enter a user code to silence the siren.
No alarms will be sent and no reports will be sent unless a communicator test is performed, at which
time a test signal will be sent.
Detector reset function
This function is used to reset Smoke Detectors and Zone Troubles. Your system must be Disarmed to use
the Reset function.
Step 1
Step 2
Press [r]-[7]. Resets have now been performed. The FIRE light will go off if the smoke
detectors have been reset.
If the keypad begins beeping, the reset did not execute properly. Enter your code to silence
the keypad. Wait a few minutes and repeat step 2 to attempt another reset. If the keypad still
beeps after repeated attempts, please contact your installer.
NX-1208E User manual
Page 13
04/10/04
g
GE Security
Setting the system clock
Step 1
Enter [r][9][7].
Step 2
Enter [master code].
Step 3
Enter the “hour code” which must be two (2) digits.
Note: The clock is a 24-hour clock. Refer to the following table.
Step 4
Time
Hour Code
Time
Hour Code
Time
Hour Code
12:00 Midnight
00
8:00 AM
08
4:00 PM
16
1:00 AM
2:00 AM
3:00 AM
4:00 AM
01
02
03
04
9:00 AM
10:00 AM
11:00 AM
12:00 Noon
09
10
11
12
5:00 PM
6:00 PM
7:00 PM
8:00 PM
17
18
19
20
5:00 AM
6:00 AM
7:00 AM
05
06
07
1:00 PM
2:00 PM
3:00 PM
13
14
15
9:00 PM
10:00 PM
11:00 PM
21
22
23
Enter the “minutes code” which must be two (2) digits.
Example: 7 minutes after would be entered [0] – [7].
Setting the system date
Step 1
Enter [r] [9][6].
Step 2
Enter [master code].
Step 3
Enter the “Day of Week “
1 = Sunday
3 = Tuesday
2 = Monday
4 = Wednesday
5 = Thursday
6 = Friday
Step 4
Enter the “Month Code”. Must always be two (2) digits.
01 = January
05 = May
09 = September
02 = February 06 = June
10 = October
03 = March
07 = July
11 = November
04 = April
08 = August
12 = December
Step 5
Enter the “Day Code”. Must always be two (2) digits.
Example: The 5th would be entered as [0] – [5].
Step 6
Enter the last two digits of the “Year Code”.
Example: For 2003 enter [0] – [3].
7 = Saturday
Setting the keypad lighting
Step 1
Press [r]-[9]-[1]. The service light will flash
Step 2
Press the [1] and [2] keys to lighten or darken the illumination behind the buttons. It is usually
easier to set this adjustment in a darkened room.
NX-1208E User manual
Page 14
04/10/04
g
GE Security
KEYPAD CONTROL TONES (BEEPS)
A sounder is built into the keypad. If programmed, your system keypad may sound for any of the following
reasons:
• Beeps for all keypresses.
• Sounds a continuous tone during the Entry delay time.
• Pulses when a day zone is violated while the system is disarmed.
• Pulses when a FIRE zone has a trouble condition.
• Beeps 3 times for trying to arm with the “Ready” light off, if “Force Arming” has not been selected.
• Beeps for 1 second or emits a “ding-dong” sound for the “Chime” feature.
• Beeps during an exit delay; beeps rapidly for the last 10 seconds of an exit delay; and beeps 1
second at the end of the exit delay.
• Pulses when the armed status changes and the AC power is off.
• Pulses when the armed status changes and any zone(s) are bypassed.
• Pulses when the armed status changes and a low battery is detected.
• Pulses when the armed status changes and a Tamper condition is detected.
• Beeps to indicate Telephone Line Cut, if selected.
• Pulses when one or more of the following conditions are detected: Zone or Box Tamper, Low Battery,
AC Power Fail, or Expander trouble.
• Beeps 3 times every minute indicating a low battery or missing transmitter is detected (if wireless
device is in system). Entering code will suppress the sounder for 12 hours.
Entering a valid code will silence the keypad sounder when it is pulsing. The arm/disarm state of your system
will not change when entering a code to silence a pulsing keypad sounder. Please contact your installer if a
trouble condition exists.
NX-1208E User manual
Page 15
04/10/04
g
GE Security
APPENDIX A – REFERENCE TABLES
IMPORTANT
These reference tables on the following pages
need to be completed by your installer.
Keep these tables in a safe place!
Installing/Service Company
: ______________________________
Address
: ______________________________
______________________________
Telephone number
: ______________________________
Name central station
: ______________________________
Telephone number central station
: ______________________________
Function codes programmed
Function code Controls function (action)
Entry/exit delay times in seconds :
Exit delay time:
Entry delay time:
Secondary Exit delay time:
Secondary Entry delay time:
This system counts ______ zones
Programmed functions:
Abort delay
Battery test
Cancel alarm
Change partitions (LED)
Chime
Communicator test
Manual fire alarm
Manual medical alarm
Manual panic alarm
NX-1208E User manual
Forced arming
Group bypass
Quick arm
Re Exit
Service Light/Message enabled
Siren test
Page 16
04/10/04
g
GE Security
Zone descriptions
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Zone 7
Zone 8
NX-1208E User manual
Page 17
04/10/04
www.gesecurity.com
EMEA Distribution is a division of GE Security EMEA bvba
COPYRIGHT ©2004
© GE Security EMEA bvba. All rights reserved. GE Security EMEA bvba grants the right to reprint this
manual for internal use only. GE Security EMEA bvba reserves the right to change information without
notice.