NAD VISO FIVE Operating Instructions Manual

VISO FIVE
РУССКИЙ
SVENSKA
Owner’s Manual
NEDERLANDS
DEUTSCH
ITALIANO
ESPAÑOL
FRANÇAIS
DVD Surround Sound Receiver
ENGLISH
®
Downloaded From Disc-Player.com NAD Manuals
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
Save these instructions for later use.
Follow all warnings and instructions marked on the
audio equipment.
FRANÇAIS
ESPAÑOL
ITALIANO
DEUTSCH
NEDERLANDS
SVENSKA
1Read instructions - All the safety and operating instructions should be
read before the product is operated.
2Retain instructions - The safety and operating instructions should be
retained for future reference.
3Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4Follow Instructions - All operating and use instructions should be
followed.
5Cleaning - Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
6Attachments - Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7Water and Moisture - Do not use this product near water-for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.
8Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to
a child or adult, and serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table recommended by the manufacturer,
or sold with the product. Any mounting of the product should follow
the manufacturer’s instructions, and should use a mounting accessory
recommended by the manufacturer.
9
A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
10Ventilation - Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s instructions have
been adhered to.
11Power Sources - This product should be operated only from the type
of power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product dealer or
local power company.
The primary method of isolating the amplifier from the mains supply
is to disconnect the mains plug. Ensure that the mains plug remains
accessible at all times. Unplug the AC power cord from the AC outlet if
the unit will not be used for several months or more.
12Grounding or Polarization - This product may be equipped with a
polarized alternating-current line plug (a plug having one blade wider
than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
13Power - Cord Protection - Power-supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
РУССКИЙ
Downloaded From Disc-Player.com NAD Manuals
14Outdoor Antenna Grounding - If an outside antenna or cable system
is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges
and built-up static charges. Article 810 of the National Electrical Code,
ANSI/NFPA 70, provides information with regard to proper grounding
of the mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors, location
of antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer’s attention to Section
820-40 of the NEC which provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.
15Lightning - For added protection for this product during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the product due to lightning
and power-line surges.
16Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be
fatal.
17Overloading - Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of fire or
electric shock.
18Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
WARNING: The apparatus should noT be exposed to
dripping or splashing, and objects filled with liquids,
such as vases, should not be placed on the apparatus.
As with any electronic products, use care not to spill
liquids into any part of the system. Liquids can cause a
failure and/or a fire hazard.
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
CAUTION
This DVD Receiver employs a Laser System. To ensure proper use of this
product, please read this owner’s manual carefully and retain for future
reference. Should the unit require maintenance, contact an authorized
service location. Use of controls, adjustments or the performance of
procedures other than those specified may result in exposure to laser
radiation. To prevent direct exposure to laser beam, do not try to open the
enclosure. Visible laser radiation when the enclosure is opened.
DO NOT STARE INTO BEAM.
FRANÇAIS
INDUSTRY CANADA REQUIREMENT
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN
AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER
TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE”
WITHIN THE PRODUCT’S ENCLOSURE THAT MAYBE OF
SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC
SHOCK TO PERSONS.
ITALIANO
ESPAÑOL
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS
INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT
OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN
THE LITERATURE ACCOMPANYING THE APPLIANCE.
The equipment draws its nominal non-operational power from the AC
outlet with its POWER switch in the STANDBY position.
The socket-outlet shall be installed near the apparatus and shall be easily
accessible.
DEUTSCH
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
FCC WARNING
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
CAUTION
Changes or modifications to this equipment not expressly approved by
NAD Electronics for compliance could void the user’s authority to operate
this equipment.
CAUTION REGARDING PLACEMENT
To maintain proper ventilation, be sure to leave a space around the unit
(from the largest outer dimensions including projections) that is equal to or
greater than shown below.
Left and Right Panels: 10 cm
Rear Panel: 10 cm
Top Panel: 50 cm
SVENSKA
FCC NOTICE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
РУССКИЙ
This equipment generates, uses and can radiate radio frequency energy and if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Downloaded From Disc-Player.com NAD Manuals
NEDERLANDS
19Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the product to its normal operation.
e) If the product has been dropped or damaged in any way.
f) when the product exhibits a distinct change in performance-this
indicates a need for service.
20Replacement Parts - When replacement parts are required, be
sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
21 Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
22Wall or Ceiling Mounting - The product should be mounted to a wall
or ceiling only as recommended by the manufacturer.
23Heat - The product should be situated away from heat sources such as
radiators, heat registers, stoves or other products (including amplifiers)
that produce heat.
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
FRANÇAIS
IMPORTANT INFORMATION FOR UK CUSTOMERS
DO NOT cut off the mains plug from this equipment. If the plug fitted is not
suitable for the power points in your home or the cable is too short to reach
a power point, then obtain an appropriate safety approved extension lead
or consult your dealer. If, nonetheless, the mains plug is cut off, REMOVE
THE FUSE and dispose of the PLUG immediately, to avoid possible shock
hazard by inadvertent connection to the mains supply. If this product is
not provided with a mains plug, or one has to be fitted, then follow the
instructions given below:
NOTES ON ENVIRONMENTAL PROTECTION
At the end of its useful life, this product must not be disposed
of with regular household waste but must be returned to a
collection point for the recycling of electrical and electronic
equipment. The symbol on the product, user’s manual and
packaging, point this out.
The materials can be reused in accordance with their markings. Through
re-use, recycling of raw materials or other forms of recycling of old
products, you are making an important contribution to the protection of
our environment. Your local administrative office can advise you of the
responsible waste disposal point.
IMPORTANT
DO NOT make any connection to the larger terminal which is marked with
the letter ‘E’ or by the safety earth symbol or colored GREEN or GREEN AND
YELLOW.
NOTE: The VISO FIVE is not an auto voltage DVD Receiver.
Connect only to the prescribed AC outlet, i.e., 120V 60Hz
or 230V 50Hz.
ESPAÑOL
The wires in the mains lead on this product are colored in accordance with
the following code:
BLUE – NEUTRAL
BROWN – LIVE
ITALIANO
As these colors may not correspond with the colored markings identifying
the terminals in your plug, proceed as follows:
The BLUE wire must be connected to the terminal marked with the
letter ‘N’ or colored BLACK.
The BROWN wire must be connected to the terminal marked with the
letter ‘L’ or colored RED.
RECORD YOUR MODEL NUMBER (NOW, WHILE YOU CAN SEE IT)
The model and serial number of your new VISO FIVE are located on the
back of the cabinet. For your future convenience, we suggest that you
record these numbers here:
Model no:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial no.: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When replacing the fuse, only a correctly rated and approved type should
be used, and be sure to re-fit the fuse cover.
IF IN DOUBT CONSULT A COMPETENT ELECTRICIAN.
DEUTSCH
NEDERLANDS
SVENSKA
РУССКИЙ
NAD is a trademark of NAD Electronics International, a division of Lenbrook Industries Limited
Copyright 2009, NAD Electronics International, a division of Lenbrook Industries Limited
Downloaded From Disc-Player.com NAD Manuals
INTRODUCTION
THANK YOU FOR CHOOSING NAD.
The VISO FIVE DVD Surround Sound Receiver is a technologically advanced
and highly capable product — yet we have invested great effort in making
it simple and easy to use. The VISO FIVE delivers a range of genuinely useful
options for surround sound and stereo listening, using powerful digital
signal processing and superbly accurate digital-audio circuitry. However,
we have also been careful to ensure that the VISO FIVE is as musically
transparent and spatially accurate as possible, incorporating much of
what we’ve learned from a quarter century’s experience designing audio
and home-theater components. As with all our products, NAD’s “Music
First” design philosophy guided the VISO FIVE’s design, such that it can
confidently promise you both state-of-the-art surround home-theater and
audiophile-quality music listening for years to come.
Downloaded From Disc-Player.com NAD Manuals
Reference
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
FRANÇAIS
ESPAÑOL
ITALIANO
OPERATION
USING THE VISO FIVE – AUDIO SETUP MENU. . . . . . . . . . . . . . . . . . . . . 14
AUDIO SETUP MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
LISTENING MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
INPUT SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SPEAKER SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SPEAKER DISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
CHANNEL LEVELS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
USING THE VISO FIVE – VIDEO SETUP MENU . . . . . . . . . . . . . . . . . . . . . 18
VIDEO SETUP MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
DISC VIDEO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
HDMI Res (RESOLUTION). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
DISC AUDIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DISC LANGUAGE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
PARENTAL CONTROL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DivX SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
OSD LANGUAGE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
using VISO FIVE – FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ABOUT THE VISO FIVE INTERNAL DVD PLAYER. . . . . . . . . . . . . . . . . . . . . . . 21
REGION MANAGEMENT INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
DISC LOADING AND PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
TITLE AND MENU BUTTONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
RANDOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
REPEAT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SLOW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
STILL PICTURE AND FRAME-BY-FRAME PLAYBACK . . . . . . . . . . . . . . . . . . 22
DEUTSCH
SETUP
SETTING UP THE VISO FIVE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ABOUT THE ON-SCREEN DISPLAY (OSD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SELECTING SOURCES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ADJUSTING THE VOLUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ADJUSTING CHANNEL LEVELS “ON THE FLY”. . . . . . . . . . . . . . . . . . . . . . . . . 13
ADJUSTING THE TONE CONTROLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
FACTORY DEFAULT SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
NEDERLANDS
IDENTIFICATION OF CONTROLS
FRONT PANEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
REAR PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SVENSKA
INTRODUCTION
ABOUT VISO FIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
E.A.R.S. AND DIGITAL SURROUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
EASE OF USE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
RS 232. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
UPGRADABILITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ABOUT THE HTR 7 SYSTEM REMOTE CONTROL. . . . . . . . . . . . . . . . . . . . . . . 6
GETTING STARTED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
WHAT’S IN THE BOX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CHOOSING A LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
QUICK START. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ZOOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
PROGRAMMING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
PLAYING MP3/WMA/JPEG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
TIMER SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
AUTOMATIC POWER OFF FUNCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
USING THE VISO FIVE - AM/FM/DB/iPod. . . . . . . . . . . . . . . . . . . . . . . . . . 24
LISTENING TO AM/FM RADIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
ABOUT ANTENNAS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
ASSEMBLING THE LOOP ANTENNA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
SELECTING THE RADIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
SETTING RADIO PRESET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
CHOOSING TUNER MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
ABOUT USER NAMES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
ABOUT RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
VIEWING RDS TEXT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
ABOUT DAB RADIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
CONNECTING THE DAB MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
DAB OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SERVICE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
DAB TUNER MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
LOCAL SCAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
PRESET TUNE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
STATION ORDER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
DYNAMIC RANGE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
TUNE AID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
PRUNE LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
INFORMATION SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
ABOUT XM RADIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
ABOUT THE iPod INPUT FEATURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
CONNECTING THE OPTIONAL “NAD IPD 1 Dock with
iPod” and iPod PLAYER TO THE VISO FIVE. . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
iPod MENU OPTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
CONTROL FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
TO VIEW VIDEOS OR PHOTOS LOADED IN YOUR iPod. . . . . . . . . . . . . . . . 29
USING THE HTR 7 REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
CONTROLLING THE VISO FIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
LEARNING CODES FROM OTHER REMOTES. . . . . . . . . . . . . . . . . . . . . . . . . . 31
PUNCH-THROUGH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
COPY COMMAND FROM ANOTHER BUTTON. . . . . . . . . . . . . . . . . . . . . . . . 31
MACRO COMMANDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
BUTTON ILLUMINATION TIMEOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
FACTORY RESET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
DELETE MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
LOADING CODE LIBRARIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
SEARCH MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
CHECKING CODE-LIBRARY NUMBER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
SLEEP MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
We encourage you to take a few minutes now to read right through this
manual. Investing a little time here at the outset might save you a good
deal of time later, and is by far the best way to ensure that you make the
most of your investment in the NAD VISO FIVE, and get the most from this
powerful and flexible home-theater component.
One more thing: We urge you to register your VISO FIVE ownership on the
NAD Worldwide Web site:
http://NADelectronics.com/warranty
РУССКИЙ
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ENGLISH
TABLE OF CONTENTS
For warranty information contact your local distributor.
INTRODUCTION
ABOUT VISO FIVE
ENGLISH
FRANÇAIS
Though the VISO FIVE is among the most technically sophisticated DVD
Surround Sound Receivers, we worked hard to make it one of the most
musically transparent home-theater components available as well; this is what
we mean by NAD’s “Music First” design philosophy. Here are just few examples:
• High-performance components used throughout VISO FIVE’s analog
audio circuits to maximize quality from all sources, including multichannel analog sources such as DVD-Audio.
• The VISO FIVE has exceptional playability. It has support for DVD-Video,
DVD-R/-RW/+R/+RW, DVD-A, SVCD with or without PBC (Play Back
Control), VCD, DivX, Audio CD, CD-R/-RW and including recorded MP3,
copyright-protected WMA and JPEG files.
• An RS-232 port for advanced zone control and software update through
a Windows® compatible PC.
• Gold-surfaced connectors are employed throughout to ensure
maximum signal integrity.
ESPAÑOL
E.A.R.S. AND DIGITAL SURROUND
ITALIANO
A key element of the VISO FIVE’s unique musical aptitude is NAD’s
proprietary Enhanced Ambience Recovery System (EARS). In sharp contrast
to many “ambience-synthesis” music-surround modes, EARS exploits the
VISO FIVE’s substantial DSP power to route the ambient content that is
“encrypted” in virtually all natural-acoustic recordings to the appropriate
main, center and surround speakers, without resorting to artificially
generated reflections or regeneration. EARS’ natural ambience yields a
subtle but exceptionally effective surround mode that naturally enhances
the spatial presentation in a fashion suitable for serious music listening.
Dolby Pro Logic II Music and DTS Neo:6 Music modes can also create
enjoyable experience from 2-channel sources.
DEUTSCH
On the digital side, the VISO FIVE combines extraordinarily high-speed DSP
processing employing one of the most advanced high-speed DSP “engines”
available. A single, high-precision master clock synchronizes all digital
circuits to eliminate the timing errors (jitter) that otherwise compromise
sonics. The result is legitimately state-of-the-art surround decoding
from Dolby Digital and DTS sources, and 5.1-channel reproduction, with
genuinely superior sound quality in all modes.
EASE OF USE
NEDERLANDS
Despite the effort NAD has invested in the VISO FIVE’s sonic performance,
we expended no less in making it powerfully easy to use. Its design is
uniquely simple for so sophisticated a component, and the HTR 7 universal
remote control is equally understandable, as are the VISO FIVE’s own frontpanel and on-screen displays.
SVENSKA
РУССКИЙ
Downloaded From Disc-Player.com NAD Manuals
RS 232
Flexible system configuration is possible with the RS-232 interface and
NAD’s proprietary Windows® compatible software. We are also certified
partners with AMX and Crestron and fully support these external devices.
This interface allows complete remote control of the VISO FIVE from any
remote location via the PC. Complete remote control functionality is
available to the user by interface software. See your NAD audio specialist for
further information.
UPGRADABILITY
The VISO FIVE permits flexible system growth. We have made the more
likely scenario of software upgrades easy to accomplish via the high speed
RS-232 port on the rear panel (and in combination with the LOAD SW
switch also on the rear panel). Owners who register their VISO FIVE on
our international web site www.NADelectronics.com will be advised of
updates. Some of these may be free of charge, and some may require
royalty payments depending on the type of upgrade. The advanced user
will be able to perform these upgrades by downloading files from our web
site, via e-mail and installing them by connecting the VISO FIVE to a PC.
Alternatively the dealer from whom you purchased your VISO FIVE should
be able to assist in performing these upgrades.
ABOUT THE HTR 7 SYSTEM REMOTE CONTROL
Packed with your VISO FIVE is the NAD HTR 7 remote control, a full-system
remote especially designed for easy use and understanding. Be sure to
read the section “Using the HTR 7 Remote Control”, to familiarize yourself
with the remote’s layout and operations before proceeding to setup your
VISO FIVE. You may opt to use your HTR 7 as your primary way to command
your entire AV system. The HTR 7 can be employed to operate additional
NAD or other-brand components such as a DVD/CD player, television,
satellite/HDTV tuner, VCR, or virtually anything else that operates via
standard infrared remote.
INTRODUCTION
CHOOSING A LOCATION
Choose a location that is well ventilated (with at least several inches to
both sides and behind), and that will provide a clear line of sight, within
23 feet/7 meters, between the VISO FIVE’s front panel and your primary
listening/viewing position—this will ensure reliable infrared remote control
communications. The VISO FIVE generates a modest amount of heat, but
nothing that should trouble adjacent components.
It is especially important that sufficient ventilation be provided. If you are
contemplating on locating the VISO FIVE within a cabinet or other furniture,
consult your NAD audio/video specialist for advice on providing adequate
airflow.
PLAY A CD OR DVD MOVIE
• Connect the VISO FIVE’s composite Video or S-Video “MONITOR OUT”
jack to your TV/monitor’s corresponding input.
• Connect your speakers to the VISO FIVE’s FRONT R, FRONT L, SURROUND
R, SURROUND L and CENTER terminals. Make sure to connect red
to red (“+”) and black to black (“-”) with care to avoid stray wires or
strands crossing between terminals. If your system includes a powered
subwoofer, connect the VISO FIVE’s “SUBWOOFER PRE-OUT” jack to its
line input.
• Connect the AC cord to the AC inlet and then plug into an AC outlet;
the LED indicator around the POWER button will be illuminated amber
indicating the VISO FIVE is in standby mode ready to accept commands
from either the front panel power switch or the HTR 7 remote.
• Press “DVD” at the HTR 7 remote’s Device Selector section and then
“OPEN/CLOSE” button.
• Insert the media and press [ PLAY] button to start playback. You
should hear sound from VISO FIVE, and see an image on the TV/monitor.
(If one or the other fails to appear, check your TV/monitor’s input
settings or VISO FIVE’s audio/video connections).
FRANÇAIS
SAVE THE PACKAGING
Please save the box and all of the packaging in which your VISO FIVE
arrived. Should you move or otherwise need to transport your VISO FIVE,
this is by far the safest container in which to do so. We’ve seen too many
otherwise perfect components damaged in transit for lack of a proper
shipping carton, so please: Save that box!
Please make all the connections to your VISO FIVE with the unit unplugged.
It is also advisable to power-down or unplug all associated components
while making or breaking any signal or AC power connections.
ESPAÑOL
QUICK START
In case you simply cannot wait to experience the performance of your
new NAD VISO FIVE, we provide the following “Quick Start” instructions to
get you underway. Before the steps below, connect your VISO FIVE to a
TV/monitor.
ITALIANO
WHAT’S IN THE BOX
Packed with your VISO FIVE you will find
• An AM loop antenna.
• A FM ribbon-wire antenna with balun.
• A removable AC cable (if you wish, any IEC-standard AC cable of suitable
wattage may be substituted).
• The HTR 7 remote control with 4 (four) AAA batteries.
• This owner’s manual.
ENGLISH
GETTING STARTED
РУССКИЙ
SVENSKA
NEDERLANDS
DEUTSCH
Enjoy the movie or music, but be sure to set aside time to read this manual
thoroughly, and to set up, calibrate, and configure your VISO FIVE carefully
and completely.
Downloaded From Disc-Player.com NAD Manuals
IDENTIFICATION OF CONTROLS
FRONT PANEL
ENGLISH
1
2
3
4
5
6
7
9
10 11 12
13
19
18 17 16 15
14
FRANÇAIS
8
ESPAÑOL
21
20
1POWER BUTTON: Press this button or the HTR 7 remote’s [ON] button
to switch ON the VISO FIVE. The Standby LED indicator will turn from
amber to blue and illuminate the VFD. Pressing the power button again
or HTR 7’s [OFF] button turns the unit back to standby mode.
ITALIANO
Note that when you do choose to switch OFF to standby using the front
panel Power button, the VISO FIVE’s memory back-up system will store
channel level, tuner preset, and other settings for several weeks while
the unit is switched off.
Pressing the [OPEN/CLOSE] button on the front-panel or the HTR 7
remote’s [ ] button will switch ON the VISO FIVE from standby mode
and at the same time open the disc tray.
DEUTSCH
NOTE
It takes around 10 seconds for VISO FIVE to switch to full standby mode
when it is powered OFF from source inputs other than DVD mode. In this
condition, it also takes around 10 seconds for the standby LED to switch
from blue to amber color.
NEDERLANDS
2 STANDBY LED: This indicator will light up amber when the VISO FIVE
is in standby state. When the VISO FIVE is at ON state, this indicator will
illuminate blue.
3NAVIGATION AND ENTER BUTTONS: The navigation buttons
[PRESET
/
] / [TUNE
/
] in conjunction with the [ENTER]
button allows one to navigate the OSD, title and menu options.
SVENSKA
РУССКИЙ
In AM/FM/XM mode, use [PRESET
/
] to step up or down
between radio presets. “Unused” presets are skipped over. Note that
Presets must have been previously stored. Refer also to the item on
“SETTING RADIO PRESET” under “OPERATION - USING THE VISO FIVE
– AM/FM/DB/iPod” discussions.
Pressing momentarily the [TUNE
/
] button will manually scan the
AM or FM band. Press and hold for more than 2 seconds to search up or
down; the VISO FIVE’s tuner will stop at the next sufficiently strong signal it
encounters. Note that this function, too, “wraps” and will continue searching
up or down from one end of the AM or FM band to the other.
At DVD mode, press [
] to skip forward or [
] to skip backward a
track, file or chapter. Press [
/
] during disc playback to select the
desired scanning speed.
Downloaded From Disc-Player.com NAD Manuals
When setting up the Timer, use the [
hours and minutes.
/
] buttons to change the
4MENU: Press this button to bring up the DVD disc menu during DVD
disc playback, stop, pause or stop-resume mode. At FM/XM/DAB mode,
the MENU button also functions the same way as that of TUNER MODE
button. See also TUNER MODE description below.
5DISPLAY: At TUNER mode, toggle this multifunction button to display
at the VFD relevant information of a currently tuned FM, XM or DAB
station.
At CABLE/SAT, VCR or Front source mode, toggle DISPLAY button to
select optical, coaxial audio input or the assigned analog audio input of
the particular source.
When in DVD mode, toggle DISPLAY button to alternatively display the
general disc playback status of the DVD display navigation menu.
6MEMORY: Use to store tuned stations to the VISO FIVE’s preset-memory
locations. Refer also to the item on “SETTING RADIO PRESET” under
“OPERATION - USING THE VISO FIVE – AM/FM/DB/iPod” discussions.
7REMOTE SENSOR: Point the HTR 7 remote control at the remote
sensor and press the buttons. Do not expose the remote sensor of the
VISO FIVE to a strong light source such as direct sunlight or illumination.
If you do so, you may not be able to operate the VISO FIVE with the
remote control.
Distance: About 23ft (7m) from the front of the remote sensor.
Angle: About 30o in each direction of the front of the remote sensor.
8 Vacuum Fluorescent Display (VFD): Provides visual
information about the unit’s important modes, settings, functions,
status of the current source like disc playback time and other indicators.
9TIMER ON/OFF: In combination with [PRESET
/
] and
[MEMORY] buttons, press and hold or toggle to set the internal clock,
ON/OFF timer as well as enable the timer modes. Refer also to the
item on “TIMER SETUP” under “OPERATION – USING THE VISO FIVE
– FEATURES” discussions.
10FM/AM/DB: Toggle this button to select either AM, FM, DAB (Europe
version) or XM (North America version) tuner functions.
IDENTIFICATION OF CONTROLS
13VOLUME: Turn clockwise to increase the master-volume setting;
counter clockwise to lower it. The VOLUME knob is also used to
increment/decrement the Bass and Treble levels.
14INPUT SELECTOR: Use to select an audio/video input source along
with its assigned analog or digital inputs. Rotate clockwise or counter
clockwise to select - Internal DVD Cable/Sat VCR (iPod) Front
AM/FM/XM (DAB) Ext 5.1 then back to Internal DVD.
15 SURROUND MODE: Toggle to select through the SURROUND MODE
options. See also the section “LISTENING MODE” under “OPERATION
- USING THE VISO FIVE – AUDIO SETUP MENU” discussions.
NOTES
• Depending on the format of the currently selected input (digital or
analog), different surround modes will be available.
• For best results when recording to a VCR, select “Mode: Stereo” and “Sub:
Off” in the applicable Setup Menu OSD.
FRANÇAIS
18OPEN/CLOSE: Press this button to open and close the disc drawer and
simultaneously select the internal DVD/CD player. Pressing this button
will also switch ON the VISO FIVE from standby mode and at the same
time open the disc tray.
19 DISC TRAY: With the DISC TRAY open, insert a DVD, VCD, CD or other
compatible media disc face down onto the tray. If the disc is placed
upside down and it is a single sided disc, “NO DISC” appears on both the
VISO FIVE’s VFD and the TV/Monitor screen.
20FRONT INPUT: Use these convenience jacks for occasional sources
such as a camcorder, tape player, or a video game console or any
other analog audio, or composite or S-Video video source. Select the
“Front” source input using the HTR 7 remote or the front panel INPUT
SELECTOR knob.
ESPAÑOL
12TONE: Press to toggle through Bass, Treble, Tone Defeat and Tone
Active options. Use the VOLUME knob to adjust the Bass and Treble
levels. While at either Bass or Treble mode, rotate VOLUME knob
clockwise or counterclockwise to adjust the Bass or Treble level within
the range ±12dB.
17PLAY/PAUSE: Press this button to toggle between Play and Pause
of a compatible disc. If the disc tray is open, press this button to
automatically close the tray and start playback if a disc is loaded.
ITALIANO
At FM/XM/DAB mode, the MENU button also functions the same way as
that of TUNER MODE button.
If your source has a single audio out jack only or is marked “mono
output”, plug this into the VISO FIVE’s FRONT INPUT “R (MONO)” input.
On the other hand, if your source has two output jacks indicative of
stereo output, insert both jacks into the VISO FIVE’s corresponding
FRONT INPUT “L” and “R (MONO)” input to achieve stereo output as well.
РУССКИЙ
SVENSKA
21PHONES: Accepts stereo headphone using a standard 1/4-inchstereo
phone plug (use a suitable adaptor for headphones equipped with a
smaller plug). Plugging in headphones automatically mutes output
from all channels’ speakers but not from the AUDIO OUT jacks of the
VCR and SCART OUT (Europe version only). See also the item on DOLBY
HEADPHONE under the LISTENING MODE section of AUDIO SETUP
MENU discussion.
DEUTSCH
16 STOP: During disc playback, press this button to STOP and at the same
time PAUSE disc playback – “RESUME” will be shown at the VFD. Press
[PLAY/PAUSE] button to resume play from the spot it was stopped. If [STOP]
button is pressed consecutively during playback, disc playback will fully
stop. At full stop mode, “STOP” will be shown in the VFD for DVD playback,
total number of tracks and total playback time for CD playback and
“CLIPMENU” is displayed in the case of MP3/WMA/JPEG file playback.
NEDERLANDS
11TUNER MODE: In FM mode, this button will toggle between FM Stereo
and FM mono. Select FM Mono (FM STEREO and FM MUTE icons at VFD
are extinguished) for stations that have too much interference or are
too weak. In DAB (European version only) or XM (North America version
only) radio, this button enables the digital radio menus in conjunction
with the Navigation button and ENTER buttons.
ENGLISH
FRONT PANEL
Downloaded From Disc-Player.com NAD Manuals
IDENTIFICATION OF CONTROLS
REAR PANEL
ENGLISH
7
8
9
10
11
14
4
5
15
16
17
18
FRANÇAIS
12 13
ESPAÑOL
1
2
3
6
ITALIANO
ATTENTION!
Please make sure that the VISO FIVE is powered off or unplugged before making any connections. It is also advisable to power-down or unplug all
associated components while making or breaking any signal or AC power connections.
DEUTSCH
1 SPEAKERS: Connect the respective SPEAKER’s FRONT L, FRONT R,
CENTER, SURROUND LEFT and SURROUND RIGHT channels to their
corresponding loudspeakers. Make sure the “+” (red) terminal and
“ - ” (black) terminal are connected to the corresponding “+” and “ - ”
terminals of the loudspeaker. Use extra care to ensure that no stray
wires or strands cross between posts or terminals at either end.
NEDERLANDS
The VISO FIVE is designed to produce optimum sound quality when
connected to speakers with impedances within its operating range.
Please make sure that all the speakers are rated 8 ohms minimum per
speaker.
4MONITOR (S-VIDEO, VIDEO): Connect to video input of a monitor/
television using quality dual-RCA and/or S-Video cables designed for
video signals. In general, the S-Video connection is superior and should
be used if your TV/monitor provides the corresponding input.
5COMPONENT VIDEO IN, COMPONENT VIDEO OUT: Connect the
Component Video IN to Component Video outputs from compatible
source components, typically a DVD player and terrestrial or satellite HDTV
tuner. Connect Component Video OUT to the Component Video input
of a compatible video monitor/TV. Be sure to observe consistency in
connecting the Y, Cb/Pb, Cr/Pr jacks to the corresponding sources/inputs.
SVENSKA
Note
Use stranded wire of at least 16 gauge (AWG). Connections to the
VISO FIVE can be made with banana plugs (US model only) or by using
bare wire or pins. Use the transverse hole through the post for bare-wire
or pin connections. By loosening the terminal’s plastic nut, make a
clean, neat connection and re-tighten carefully. To minimize the danger
of short-circuit, ensure that only 1/2-inch of exposed wire or pin is
employed when connecting.
6 SCART/RGB OUT (Euro model/PAL only): Connect the VISO FIVE’s
“SCART/RGB OUT” to the SCART/RGB video input of a compatible
video monitor/TV. Be sure to observe the correct orientation of the
SCART/RGB plug. Make sure also to set “Video Output” to “RGB” at the
“Disc Video” menu for stable video at SCART/RGB OUT.
2 12V trigger out: The 12V TRIGGER OUT is used for controlling
external equipment that is equipped with a 12V trigger input. This
output will be 12V when the VISO FIVE is ON and 0V when the unit is
either OFF or in standby.
8RS-232: Connect this interface via RS-232 serial cable (not supplied) to any
Windows® compatible PC to allow remote control of the VISO FIVE through
NAD’s proprietary PC software or other compatible external controllers.
NAD is a certified partner of AMX and Crestron and fully supports these
external devices. See your NAD audio specialist for more information.
РУССКИЙ
3CABLE/SAT & VCR: Connect to these inputs S-Video, composite
video, and analog audio from source components such as cable TV
decoders, satellite tuners, another DVD player or other applicable
ancillary devices. VCR may be used with recording components such
as videocassette or DVD-recorders. Connect the VCR OUT (audio/video)
to these components’ corresponding audio/video input. Note that VCR
may freely be used for play-only components, in which case their OUT
jacks would remain unconnected.
10
Downloaded From Disc-Player.com NAD Manuals
7RESET: In the unlikely event that the VISO FIVE becomes inoperable or
hangs up, press this button to reset the VISO FIVE.
9 SUBW (SUBWOOFER) PRE OUT: Connect this output to a powered
(active) subwoofer or to a power amplifier channel driving a passive system.
IDENTIFICATION OF CONTROLS
There is no bass-management or other processing (other than mastervolume control) available to this 5.1 Channel Input. While the multichannel audio outputs of a DVD-Video player can be connected to
these jacks, using the VISO FIVE’s own Dolby Digital and DTS decoding
and digital-analog converters via a digital connection will usually
produce superior results.
12HDMI OUT: Connect the HDMI OUT to a HDTV or projector with
HDMI input.
WARNING
Before connecting and disconnecting the HDMI cable, both the
VISO FIVE and the ancillary source must be powered OFF and unplugged
from the AC outlet. Failure to observe this practice may cause permanent
damage to the equipment connected via the HDMI socket.
IMPORTANT NOTICE
When playing DTS (or Dolby Digital) material, ensure that the volume of
your HDMI equipped TV is muted. There may be a rushing noise heard if
your TV is not capable of decoding the DTS (or Dolby Digital) Bitstream;
most TVs do not have this capability.
Connect the supplied AM loop antenna to these terminals. If an external
AM antenna is used, make connections to the AM and GND terminals
in accordance with the instructions supplied with the antenna. See also
section about “LISTENING TO AM/FM RADIO”.
17IEC AC MAINS (POWER) INPUT: The VISO FIVE comes supplied with
a separate AC Mains cable. Before connecting the cable to a live wall
socket ensure that it is firmly connected to the VISO FIVE’s AC Mains
input socket first. Always disconnect the AC Mains cable plug from the
live wall socket first, before disconnecting the cable from the VISO FIVE’s
Mains input socket.
18 SWITCHED AC OUTLET: This convenience outlet can supply switched
power to another component or accessory. It is powered ON and OFF
by the front panel POWER SWITCH or by the HTR 7’s ON and OFF keys.
13MP DOCK: The VISO FIVE is equipped with a data port in the rear panel
where an optional “NAD IPD 1 Dock with iPod” (NAD IPD 1) can be
plugged in. Connect the “MP DOCK (DATA PORT)” jack of the VISO FIVE
to the corresponding “DATA PORT” socket of the optional NAD IPD 1.
NEDERLANDS
14XM MODULE INPUT (North America version only): Connect XM
radio cable to this socket. Follow the instructions that came with your
XM radio. With XM radio, there are more than 100 channels of music,
news, sports, comedy, talk and entertainment. You will find that the
coverage is continent wide. The music quality is digital with many
commercial-free music channels.
SVENSKA
NOTE
• Questions? Visit www.xmradio.com
Listeners can subscribe by visiting XM on the Web at www.xmradio.com
or by calling (at the time of printing this manual) XM’s Listener Care at
(800) 853 9696. Be ready with your Radio ID that can be found on the
radio by selecting Channel 0.
РУССКИЙ
DAB MODULE INPUT (Europe version only): Plug-in the other end
of the Mini-Din connector from the NAD DAB Adaptor DB 1 module
output port into this socket. The VISO FIVE is compatible only with NAD
DAB Adaptor DB 1 so check with your NAD dealer for this module’s
availability. With DAB, you can receive CD-like quality programs without
any annoying interference and signal distortion.
Downloaded From Disc-Player.com NAD Manuals
FRANÇAIS
16FM, AM ANTENNA INPUT: The supplied wire “dipole” FM antenna will
connect to the FM connector using the supplied “balun” adapter. It will
usually work best when mounted on a vertical surface such as a wall,
with arms fully outstretched forming a horizontal “T” perpendicular to
the origin point of the signal.
ESPAÑOL
OPTICAL OUT: Connect the optical digital OUT port to the
corresponding S/PDIF digital input of a compatible device such as CD
recorders, receivers, computer soundcard or other digital processors.
ITALIANO
11 5.1 CH INPUT: Connect to the corresponding analog audio outputs
of a multichannel source component such as a DVD-Audio or external
multichannel decoder (disc copy protected formats only allow analog
signal transfer). The signals present at these jacks will be heard by rotating
the INPUT SELECTOR knob to select “Ext 5.1” as your source input.
15COAXIAL IN, OPTICAL IN: Connect to the optical or coaxial S/PDIFformat digital output of sources such as CD or DVD players, HDTV or
satellite tuners and other components.
DEUTSCH
10LOAD SW: For future software program updates, use this button
in combination with RS232 to upgrade the VISO FIVE. Owners who
register their VISO FIVE in our international website www.nadelectronics.
com will be advised of updates. Your custom installer or dealer can
assist you in the proper upgrade and setup of your VISO FIVE.
ENGLISH
REAR PANEL
11
SETUP
SETTING UP THE VISO FIVE
ENGLISH
ABOUT THE ON-SCREEN DISPLAY (OSD)
The VISO FIVE employs a self-explanatory on-screen display “menu” that
will appear on the connected video monitor/TV. These are required during
the setup process (and are useful in day-to-day operation), so be sure to
connect the monitor/TV before proceeding with setup.
DISPLAY DISC OSD
You can display the general disc playback status on the TV screen. Some
items can be changed using the menu. To use the on-screen display:
1 Press the HTR 7’s [DISP] during playback.
2 Press [
] to select an item. The selected item is highlighted.
3 Key-in the desired the number button or press [ENTER] as applicable.
DISPLAY THE VISO FIVE SETUP MENU
FRANÇAIS
ESPAÑOL
At any source mode, press the HTR 7’s [SETUP] button for the Setup Menu
OSD to appear. With the use of the HTR 7’s navigation buttons, you may
select various menus. If the Setup Menu does not appear, check your
applicable video connections.
ITALIANO
NOTE
The Setup Menu will not appear if a headphone is plugged-in at the
front panel’s PHONES jack. Unplug the headphone for the Setup Menu
to appear when HTR 7’s [SETUP] button is pressed.
NAVIGATING THE SETUP MENU OSD AND MAKING CHANGES
Notes
• The display feature may not be available for all disc media and is media
dependent.
• Display disc OSD does not apply to audio only discs like CD and MP3/
WMA/JPEG files as they are already presented in their respective menu
screens.
• The front panel and HTR 7’s [DISP] button toggles between title/chapter/
time (or group/track/time for DVD-A discs) and audio/subtitle/angle
display configurations.
• If no button is pressed for about 10 seconds, the on-screen display
disappears.
SELECTING SOURCES
You can choose your desired source by rotating the INPUT SELECTOR knob
to select through the following:
Internal DVD Cable/Sat VCR (iPod)
Ext 5.1 then back to Internal DVD.
Front
AM/FM/XM (DAB)
DEUTSCH
The same source can be directly selected using the HTR 7 remote control.
1 Set HTR 7’s DEVICE SELECTOR to “AMP”.
2 Press your desired source’s corresponding numeric keypad allocation. The
orange label directly above the appropriate numeric keypad is the Source
allocated for such key – example: “1” for DVD, “2” for CAB/SAT and so on.
When you change sources, the VFD will show the new input in its upper
line display.
ADJUSTING THE VOLUME
NEDERLANDS
SVENSKA
To navigate through the Setup Menu OSD options, please do the following
using the HTR 7 remote control:
1 Press [
] keys to move up or down the menu selections.
2 Press [ENTER] to select a menu.
3 Use [
] or [ENTER] keys to select through the options of a particular
menu.
4 To save a menu item that you have set up, use [ ] key to scroll down and
select the particular menu’s “Save & Exit” option. Press [ENTER] to save the
settings and at the same time exit the menu. Select “Do not Save & Exit” if
you choose not to implement the settings you have set up.
To exit the Setup menu or from a menu option without saving, press
HTR 7’s [SETUP] key.
РУССКИЙ
12
Downloaded From Disc-Player.com NAD Manuals
In addition to the Volume knob, use the HTR 7’s [VOL
] to adjust
the “master volume” of the VISO FIVE raising or lowering the channels
altogether. A momentary keypress will change the master volume by 1 dB
increments. If you hold down [VOL
] the master-volume change will
“run-on” until the key is released.
Since recordings vary considerably in overall average level, there is no
imperative to listen at any particular master-volume setting. A setting of -20
dB may sound “as loud” from one CD or DVD as -10 dB does from another.
The VISO FIVE will power-up from Standby mode at whatever master
volume setting it was last used; however, if the prior setting was greater
than –15 dB, the VISO FIVE will power up at –15 dB. This prevents
inadvertently beginning a session at excessive volume.
SETUP
ADJUSTING CHANNEL LEVELS “ON THE FLY”
You can make changes to the relative levels of center, surround and
subwoofer outputs without having to go into the “Channel Levels” menu.
This is very convenient in circumstances like increasing (or tone down)
a film’s dialog level by rising (lowering) the center channel or reducing
excessive deep bass (or enhance deep bass) by lowering (rising) the
subwoofer level.
Please note that setting the VISO FIVE to factory default will delete all AM,
FM and DAB presets. It will also reset all your timer settings.
FRANÇAIS
NOTE
Adjusting the master-volume via the HTR 7 or the front-panel knob
automatically releases the mute function.
FACTORY DEFAULT SETTINGS
Sometimes power spikes and drop-outs may from time to time cause some
inadvertent functionality. The procedure below will set the VISO FIVE to
factory default settings
1 Place the VISO FIVE into AM mode.
2 Press quickly the three front panel buttons: [PLAY/PAUSE], [STOP] then
[DISPLAY], holding the “DISPLAY” button for more than 7 seconds. The
VISO FIVE will switch itself off, then back ON to DVD mode.
ESPAÑOL
MUTING THE SOUND
Use the HTR 7’s “MUTE” key to silence all channels completely (“Mute” is
displayed in the lower line of the VFD). Muting is always available regardless
of the source or listening mode selections.
ENGLISH
SETTING UP THE VISO FIVE
Use the HTR 7’s [SURR], [CENT] and [SUB] keys for direct-access level
adjustment of these channels over a range of ±12dB.
ITALIANO
The [SURR] button will adjust first Surround Left (SL) channel level. To adjust
Surround Right channel level, press and release [SURR] button, the VFD will
show “SL” and the current Surround Left channel level. Wait for the display
to “SR” and the current surround right channel level. You can now to set
your preferred Surround Right channel level by pressing [SURR] key.
NOTE
The lower line of the VFD will display the channel being adjusted and the
corresponding level setting.
ADJUSTING THE TONE CONTROLS
DEUTSCH
The VISO FIVE bass and treble controls are adjusted using the front panel’s
[TONE] button in conjunction with the VOLUME knob. The corresponding
[TONE] and [VOL
] keys of HTR 7 can also perform the same functions.
Referring to the lower line of the VFD, toggle [TONE] button to select “Bass”,
“Treble”, “Tone Active” or “Tone Defeat”. While at either Bass or Treble mode,
rotate VOLUME knob clockwise or counterclockwise to adjust the Bass or Treble
level within the range ±12dB.
NEDERLANDS
Bass and treble settings affect only the front left/right channels, and are
active in all SURROUND MODES.
РУССКИЙ
SVENSKA
Select “Tone Defeat” to bypass the Tone Controls effectively defeating
the effect of the tone control circuits. If “Tone Active” is selected, the Tone
Control circuits are active.
Downloaded From Disc-Player.com NAD Manuals
13
OPERATION
USING THE VISO FIVE – AUDIO SETUP MENU
ENGLISH
AUDIO SETUP MENU
EARS
Two-channel recordings, whether stereo or surround-encoded, are
reproduced with proprietary NAD surround processing with signals
output to the front, center and discrete surround channels, plus subwoofer
(assuming these are present in the “Speaker Settings” menu).
FRANÇAIS
EARS extracts the natural ambience present in nearly all well-produced
stereo recordings. It does not synthesize any ambience or other sonic
elements and thus remains truer to the sound of the original musical
performance than most other music-surround options.
LISTENING MODE
ESPAÑOL
Select EARS for listening to stereo music recordings and broadcasts.
EARS produces a subtle but highly natural and believable ambience from
nearly all “natural-acoustic” stereo recordings. Typically, these include
classical, jazz, and folk genres as well as numerous examples from others.
Its virtues include realistic, stable “front-stage” sonic imaging and spacious
but unexaggerated ambient “virtual acoustics” that remain faithful to the
original recording.
ITALIANO
ENHANCED STEREO
All recordings reproduced in stereo via the maximum speaker complement
configured in the “Speaker Settings” menu. Enhanced stereo can be useful
for maximum volume from all channels or for multi-speaker background
music (cocktail party) listening. For this mode, Front, Center and Surround
can be turned “On” or “Off” as desired.
The VISO FIVE offers distinct SURROUND MODES tailored for different types
of recordings or program material. With a two-channel (Stereo) source, the
following listening modes can be selected:
DEUTSCH
PRO LOGIC PLII
Dolby Pro Logic II is a more recent evolution of the original Dolby Pro Logic
surround processing that yields more stable imaging and full bandwidth
sound to the rear channels in Movie mode, offering sound that is more
similar to Dolby Digital decoding. Two-channel recordings, whether stereo
or surround-encoded, are reproduced with Dolby Pro Logic II surround
processing, yielding output to Front, Center and Surround channels
(assuming these are present in the “Speaker Settings” menu).
NEDERLANDS
SVENSKA
PLII Movie is optimized for film soundtracks.
PLII Emulation for decoding original Dolby Surround sound film and music
recordings.
PLII Music for music recordings.
DIMENSION (-3 to +3): Adjusts front-rear emphasis of the surround
effect independently from the relative channel levels.
CENTER WIDTH (0 to 7): Modifies the “hard-centeredness” of the center
image, by gradually mixing mono center content to the Front left/right
speakers as well. A setting of 0 retains the center-channel-only default
while a setting of 7 yields a fully phantom center channel.
PANORAMA (On/Off ): Adds a “wrap around” effect by extending some
stereo content into the surround channels.
РУССКИЙ
14
Downloaded From Disc-Player.com NAD Manuals
DOLBY® VIRTUAL SPEAKER (DVS)
Dolby Virtual Speaker technology creates a highly compelling 5.1-channel
listening experience from as few as two speakers, making it an ideal
entertainment solution for locations where space for multiple-speaker
setups is limited.
Dolby Virtual Speaker models the sound of a playback system into two
different listening environments, based on acoustic measurements of real
rooms:
DVS Reference is a small, well-damped room appropriate for both
movies and music-only recordings.
DVS Wide is a larger room, more like a concert hall or movie theatre.
STEREO
All output is directed to the front left/right channels. Low frequencies are
directed to the subwoofer if one is present in the Speaker settings. Select
“Stereo” when you wish to listen to a stereo (or monaural) production, such
as music CD or FM broadcast, without surround enhancement. Stereo
recordings whether in PCM/digital or analog form and whether surroundencoded or not encoded, are reproduced as recorded. Multi-channel digital
recordings (Dolby Digital and DTS) are reproduced in “Stereo Downmix”
mode via the front left/right channels only as Lt/Rt (left/right-total) signals.
OPERATION
INPUT SETTINGS
DTS
The Digital Theater System Digital Surround (simply called DTS) is a multichannel digital signal format that can process higher data rates than with
Dolby Digital. Although both Dolby Digital and DTS are 5.1 channel media
formats, discs bearing the “DTS” symbol are thought to provide better sound
quality due to the lower audio compression required. It also offers a broader
dynamic, producing magnificent sound quality.
Downmix 2Ch: A Dolby Digital or DTS digital signal format can be
automatically downmixed to produce two-channel stereo audio.
DOLBY® HEADPHONE
Dolby Headphone technology, compatible with any pair of conventional
headphones, accurately simulates the experience of hearing a 5.1-channel
speaker system properly set up in a listening room, minus the annoying
“listener fatigue” effect that plagues other headphone-based virtual
surround sound offerings. Dolby Headphone technology is ideal for private
playback of multi-channel entertainment without disturbing others nearby.
VIDEO IN
A particular video input can be assigned to any of the following source
inputs - Cable/Sat, VCR (iPod), Front and Ext 5.1. Ideally, a video input
present at the video input of a particular source input should be assigned
to the same source input. For example, a video input present at S-video
input of VCR should be the assigned video input for VCR source input. This
is actually the default setting. This can be varied though by assigning a
different active video input other than the particular source’s default video
input setting.
AUDIO IN
Incoming digital and audio signals present at either digital or analog audio
are assignable to any of the following source inputs - Cable/Sat, VCR and
Front. Use [
] to assign coaxial, optical or analog audio to any of the
aforementioned sources.
The assigned audio input will always be recalled whenever that input is
selected using the front panel INPUT SELECTOR knob or the HTR 7 remote’s
input-select buttons.
It is not necessary to connect at the same time both analog audio and
digital audio input for every video input you employ. It is preferable to
make only digital audio link to the VISO FIVE for audio playback. This avoids
possible confusion and ensures that the VISO FIVE’s high performance
digital audio circuitry will always be employed.
ESPAÑOL
РУССКИЙ
Dolby Headphone models the sound of a playback system into three different
listening environments, based on acoustic measurements of real rooms:
DOLBY HP MODE 1 is a small, well-damped room appropriate for both
movies and music-only recordings. This decoding process is known as the
Dolby Headphone “Reference Room”.
DOLBY HP MODE 2 is a more acoustically live room suited to music
listening, but also great for movies.
DOLBY HP MODE 3 is a larger room, more like a concert hall or movie
theatre.
Select DOLBY HP OFF for normal headphone audio listening.
Downloaded From Disc-Player.com NAD Manuals
ITALIANO
IMPORTANT NOTICE
“DYN Range” will appear as one of the options under the “Listening
Mode” menu only if the disc being played is of Dolby Digital format. The
same applies when you select the digital audio input (coaxial or optical)
as your audio source – Dynamic range adjustment will be available at
the “Listening Mode” menu only if the detected audio is of Dolby Digital
format. For Dolby Digital 2.0 soundtracks, set “Mode” at the “Listening
Mode” menu to “Dolby Digital 2Ch” (“DD 2Ch Stereo” if you toggle
[SURROUND MODE] button) for “DYN Range” option to appear.
Use [
] select through DVD, Cable/Sat, VCR (iPod), Ext 5.1 and then
back to DVD.
DEUTSCH
The 100% setting is best for late-night sessions or other times when you
wish to retain maximum dialog intelligibility while minimizing overall
volume levels. To maintain full dynamic range, set “DYN Range” to “Off”.
INPUT
Aside from the VISO FIVE’s internal DVD, the VISO FIVE is also equipped with the
following audio/video source inputs - “Cable/Sat”, “VCR” (iPod) and “Front” (Front
Input on the front panel). Another source input is the “Ext 5.1” which is an audioonly input. The input becomes active whenever it is selected.
SVENSKA
DYNAMIC RANGE CONTROL (DYN Range)
You can select the effective dynamic range (subjective range from soft
to loud) for playback of Dolby Digital soundtracks. For fully cinematic
effect, always select 100% - the default. Settings of 75%, 50% and 25%
progressively reduce dynamic range, making soft sounds comparatively
louder while limiting the peak loudness of loud ones.
FRANÇAIS
DOLBY DIGITAL
Dolby Digital is the multi-channel digital signal format developed in the
Dolby laboratories. Discs bearing the double-D symbol were recorded with
up to 5.1 channels of digital signals, reproducing a much better sound
quality, with dynamic and spatial sound sensations that are much better
than in the previous Dolby Surround.
NEDERLANDS
The following Listening Modes require a specially encoded signal that
must be present in digital format to be decoded by the VISO FIVE. These
modes are automatically switched on when the appropriate data stream is
detected. The desired data stream must sometimes be selected in the setup
menu of the source media.
ENGLISH
USING THE VISO FIVE – AUDIO SETUP MENU
15
OPERATION
USING THE VISO FIVE – AUDIO SETUP MENU
ENGLISH
SPEAKER SETTINGS
FRANÇAIS
ESPAÑOL
Every surround-sound system requires “bass-management” to direct
low-frequency content from any or all channels to the speakers best able
to reproduce it. For this function to operate correctly, it is important that
you correctly identify your speakers’ capabilities. We use the terms “Large”,
“Small”, “Mini” and “Off”, but note that physical size may be irrelevant.
SPEAKER DISTANCE
Setting the Distance lets the speakers know how far the sound has to travel
to reach your set listening point. This allows the sound from each speaker to
reach the listener at the same time.
Distance can be adjusted within 1FT (0.30M) up to 30FT (9M).
Distance setting is not applicable for Subwoofer.
ITALIANO
• A “Small” speaker is any model, regardless of physical size, that lacks
significant deep-bass response. Set to SMALL if your speaker cannot
handle lower than 100 Hz.
• A “Large” speaker is any full-range model, that is, one with deep-bass
response. Set to LARGE if your speaker can handle 20 Hz - 20 kHz full
frequency range.
• Select “Mini” if your speaker cannot handle lower than 150Hz.
• Set “Subwoofer” to “On” or “Off”, selecting “On” only if you have a
subwooder connected to VISO FIVE’s SUBW output jack.
• An “Off” speaker is one that may be present such as a subwoofer but set
to “Off” in the “Speaker Settings” setup menu.
CHANNEL LEVELS
The “Speaker Settings” is “global”; that is, it remains in force with all inputs
and in all LISTENING MODES.
DEUTSCH
NEDERLANDS
ENHANCED BASS
When the subwoofer is set to ON and all speakers are set to “Large”,
Enhanced Bass is also available. Normally, with speakers set to “Large”
the subwoofer is not active. The Enhanced Bass option allows full range
operation of the speakers with the additional bass contribution of the
subwoofer. This feature is particularly useful when one wants to experience
maximum bass output. Please note that due to acoustic cancellation
effects, the bass response may be uneven when using this setting.
You can set Subwoofer to “On” even with “Large” front speakers. In such cases,
both subwoofer and front speaker will receive the LFE-channel signal. In the
case where the front speakers are set to “Small” the LFE-channel signal will be
routed to subwoofer but not to the front speakers; LFE-channel signal will pass
only to the subwoofer. In most subwoofer-equipped systems, setting front
speakers to “SMALL” is usually the better option.
Adjusting the relative balance of your system’s loudspeakers ensures that
surround-sound recordings, whether music or film, will present the balance
of effects, music, and dialog that the artists intended. Additionally, if your
system incorporates a subwoofer it establishes a correct relationship
between the volume of the subwoofer and the other speakers, and thus of
low-frequencies (bass) to other sonic elements.
USING AN SPL METER
It is quite practical to perform the VISO FIVE level setup routines “by ear”, and
careful work will produce acceptably accurate results. However, the use of an
inexpensive sound-pressure level (SPL) meter, such as Radio Shack part number
33-2050, makes this task easier, more accurate and more repeatable. Ownership
of such a meter could prove a valuable audio tool. Your NAD audio specialist
may be able to help you with temporary use of a meter.
SVENSKA
The SPL meter should be placed at the primary listening position, at
approximately the height of the seated listener’s head. A tripod is helpful
but with a little duct tape almost anything — a pole lamp, music-stand,
or ladder-backed chair, for example — can do as well. Just be sure that no
large acoustically reflective surfaces obstruct or are near the microphone
element.
РУССКИЙ
Orient the meter with its microphone (usually at one end) pointing straight
up toward the ceiling (not toward the speakers) and ensure that “C”
weighting scale is selected. Set the meter to display 75 dB SPL. On Radio
Shack meters, this necessitates either setting the meter to its 80 dB range
and taking your readings at the -5 point or selecting the 70 dB range and
reading at the +5 point.
16
Downloaded From Disc-Player.com NAD Manuals
OPERATION
ENGLISH
USING THE VISO FIVE – AUDIO SETUP MENU
FRANÇAIS
SETTING CHANNEL LEVELS IN TEST MODE
While at “Channel Levels” menu, press the HTR 7 remote’s [Test] key
activating the VISO FIVE’s Channel Levels balancing test signal (lower line
of the VFD will show “Test Tone”). You will hear a “surf” sound as you step
through your speakers beginning with the Front Left. If you do not hear the
test signal, check your speaker connections or your “Speaker settings” OSD
menu settings.
Use the remote’s [
] keys to adjust the loudness of the noise output
from the currently playing channel to the required level (it’s usually
simplest to begin with the Front Left). As you cycle the test signal around
the speakers, the OSD will highlight the currently playing channel. The
“level offset” reading on the right will change by 1 dB increments; ±12 dB
adjustment is available. Press [
] to adjust the next speaker.
ESPAÑOL
NOTE
If you are balancing levels “by ear”, choose one speaker—usually the
center— as a reference and adjust each of the others in turn to “sound as
loud” as the reference. Be sure that you remain in the primary listening
position while balancing all channels.
To produce the same SPL meter reading (or subjective loudness), use the
remote’s [
] keys to adjust each speaker.
DEUTSCH
ITALIANO
NOTES
• All speakers must be in their final locations before level-setting.
• Your subwoofer (if any) should be set with its integral crossover defeated,
or if undefeatable, set to its highest-possible frequency if you are using
the VISO FIVE’s Subwoofer output. Final subwoofer-level adjustment
“by-ear”, using music and film sound material, is frequently useful.
• Due to the effects of room acoustics, matched-pair speakers (front;
surround) will not always calibrate to exactly the same level offset
readings.
РУССКИЙ
SVENSKA
NEDERLANDS
You can exit “Test” mode at any time by pressing the HTR 7 remote’s [Test].
Downloaded From Disc-Player.com NAD Manuals
17
OPERATION
USING THE VISO FIVE – VIDEO SETUP MENU
ENGLISH
VIDEO SETUP MENU
HDMI Res (RESOLUTION)
FRANÇAIS
HDMI video resolution can be adjusted with the VISO FIVE connected to an
HDMI-compatible component via HDMI OUT.
480P/576P, 720P, 1080I : Set applicable resolution depending on your
TV/Monitor capability.
Auto : The best resolution is automatically selected based on your
TV/monitor’s capability.
Off : Select to turn off HDMI output.
DISC VIDEO
ESPAÑOL
ITALIANO
FORMAT
Set FORMAT to select a picture size matching the aspect ratio of your
TV/Monitor.
DEUTSCH
Select “Pan Scan 4:3” or “Letter Box 4:3” when a standard 4:3 TV is connected.
Letter Box 4:3 : Displays a wide picture with bands on the upper and
lower portions of the screen.
Pan Scan 4:3 : Automatically displays the wide picture on the entire
screen and cuts off the portions that do not fit.
Widescreen 16:9 : Select when a 16:9 wide TV is connected. Set the
widescreen TV to FULL mode if necessary.
NEDERLANDS
NOTE
If you have a 16:9 display device and you have defaulted “Format” to
“Widescreen 16:9”, it does not mean you will always see movies in this
format - Widescreen 16:9 display format must be supported by the disc
being played in order to view the movie in widescreen format.
SVENSKA
SIGNAL MODE
Depending on the type of TV/Monitor set you own, select the signal mode
you wish to watch your disc. Refer to your TV/Monitor’s owner’s manual to
check its signal or system mode capabilities.
Auto : Automatically detects the signal mode of your TV/Monitor.
NTSC : Select when the signal mode of your TV/Monitor is NTSC system.
PAL : Select when the signal mode of your TV/Monitor is PAL system.
РУССКИЙ
18
Downloaded From Disc-Player.com NAD Manuals
NoteS
• For settings other than “Auto”, be sure that the selected resolution
is supported by the HDMI-compatible monitor you are using. If the
selected resolution is not supported, this setting is automatically
switched to the most appropriate resolution.
• Picture quality may decrease when an HDMI cable longer than 5m is used.
IMPORTANT NOTe about hdmi connection and setting
With HDMI OUT connected to a HDMI-compatible component, component
video out, composite and S-video output will only be available when “HDMI
Res.” is set to “480P/576P” or “Off”. For component video out, composite and
S-video to come up, unplug HDMI cable or undertake the following:
1 At DVD mode and with no disc loaded, “NO DISC”, press and hold
[DISPLAY] button. The lower line of the VFD will show the current HDMI
resolution setting.
2 Use the remote’s [
] keys or toggle [MEMORY] button to select
through 480P/576P, 720P, 1080I, AUTO or OFF. Select either “480P/576P”
or “OFF” to enable component video out, composite and S-Video
output. To set preferred resolution setting, stop at your desired
resolution setting and release [
] keys or [MEMORY] button.
BRIGHTNESS
Adjust overall brightness of the image. Set the brightness level over a
range ±7. Select “BASIC” to maintain default brightness setting.
SHARPNESS
Picture sharpness could be easily lost during the recording/playback
process. Adjust sharpness to improve the fine details of the picture. Set
the sharpness level over a range ±7. Select “BASIC” to maintain default
sharpness setting.
VIDEO OUTPUT (Europe version model only)
Select between “Component” and “RGB” as your preferred video output
media. Make sure the appropriate video out of VISO FIVE is connected to
the corresponding video input of your TV/monitor.
“RGB” video setting is preferable if your output media is through SCART
OUT. At RGB setting, video signal is split into three fundamental colors Red,
Green and Blue (RGB) resulting to greater picture resolution and elimination
of artifacts associated with traditional composite video signals.
Select “Component” if you are not using SCART OUT as your output media.
OPERATION
ENGLISH
USING THE VISO FIVE – VIDEO SETUP MENU
DISC LANGUAGE
DIGITAL OUT
Set VISO FIVE’s “Digital Out” according to the type of audio system you use.
Bitstream: Select “Bitstream” if you connect the VISO FIVE’s digital OUT
jack to an amplifier or other equipment with a Dolby Digital, DTS or
MPEG decoder.
PCM: Select when connected to a two-channel digital stereo
amplifier. DVDs encoded in Dolby Digital or MPEG will be automatically
downmixed to two-channel PCM audio.
AUDIO/SUBTITLE/MENU
Depending on the DVD media, only the Audio, Subtitles and Menus
recorded on the DVD media are available. When a language is chosen, it will
become the default setting unless the DVD media overrides the settings.
DISC TYPE
Some DVD-Audio discs contain the DVD-Video content in addition to
the DVD-Audio content. You can choose DVD-Audio or DVD-Video mode
depending on your preference.
DVD-AUDIO : Select to playback both DVD-Audio and DVD-Video
contents. DVD-Audio content only may be played back depending on
the disc.
DVD-Video : Select to playback only the DVD-Video content.
PARENTAL CONTROL
ITALIANO
DEUTSCH
NEDERLANDS
PCM FORMAT
The VISO FIVE is compatible with both 48 kHz and 96 kHz PCM formats.
96kHz: Select to handle 96kHz signal - each type of signal will pass
through without any further processing.
96kHz > 48kHz: Select for 96KHz signal to be automatically converted
to 48KHz enabling decoding of compatible media.
PASSWORD
PASSWORD is needed to gain access to the “Rating Level” below. The
following are the steps for you to enable or change your password.
1 While at “Password” line menu, press [ENTER]. A menu screen like the
one shown below will appear
2 Input the 4-digit “Old Password” – the preset “Old Password” is “2580”.
3 You can now set your own password by entering your desired 4-digit
password at the “New Password” option. Press [ENTER].
4 After entering your new password, re-enter again your new 4-digit
password at the “Confirm” option. Upon entering the correct password
at “Confirm” option, the password menu window will turn off bringing
you back to “Parental Control” menu screen.
NOTE
If the password entered at “Old Password” or “Confirm” window is incorrect,
you will remain in the same menu item like “Old Password” or be returned to
“New Password”. You cannot move forward to the next sequence unless the
correct password is entered. Select “Exit” in the password menu screen to exit
the sequence if you are unable to enter the correct password.
Downloaded From Disc-Player.com NAD Manuals
19
SVENSKA
MOVING TO ANOTHER GROUP
Some DVD Audio discs divide content into different groups. Your player
enables you to quickly access different groups during playback via the
on-screen display.
1 Press DISP during playback
2 Press [
] to highlight “G”.
3 Enter group number using the numeric buttons 0-9.
Select among Original, English, French, German, Dutch, Spanish, Italian,
Russian and Swedish as the desired language setting.
If you do not want the disc’s subtitles to be shown, select “Off”.
РУССКИЙ
NoteS
• This setting is only available when no disc is loaded in the disc tray.
• Selected mode becomes effective after you exit the setup menu.
• When a DVD-Audio disc is played back, “DVD Audio” is shown in the VFD.
• When you select “DVD-Video”, “DVD-Video” will be briefly shown in the
VFD and then reverts to normal display playback information.
ESPAÑOL
FRANÇAIS
DISC AUDIO
OPERATION
USING THE VISO FIVE – VIDEO SETUP MENU
ENGLISH
RATING LEVEL (NORTH AMERICA VERSION ONLY)
Some movies contain scenes that may not be suitable for children to view.
Many of these discs contain parental control information that applies to the
complete disc or to certain scenes on the disc. Movies and scenes are rated
from 1 to 8, depending on the country. Some discs offer more suitable
scenes as an alternative.
FRANÇAIS
ESPAÑOL
The RATING feature allows you to block access to scenes greater than the
rating you have set up, thereby preventing your children from being able
to view material you believe is unsuitable. To activate “Rating”, please be
guided by the following:
1 While at “Rating” line menu, press [ENTER].
2 “Password _ _ _ _” will appear indicating that a password is needed to
change the ratings level.
3 Input the password you have setup at the “Password” item as discussed
above. Press [ENTER].
4 Upon entering the correct password, you can now set the parental
rating level you prefer. Use [
] to step through the rating levels.
5 After you have selected your preferred rating level, use [ ] to scroll
down to “Save & Exit” option. Press [ENTER] to save the rating level you
have chosen.
Rating 1-8
Rating one (1) has the most restrictions and “8” is the least restrictive.
ITALIANO
Unlock
If you select unlock, parental lock is not active and the disc plays in full.
NOTE
Should you forget your password, reset your password by restoring the
VISO FIVE to its factory default settings. Refer to the “Factory Default
Settings” section under the heading “SETUP - SETTING UP THE VISO FIVE”.
DivX SETUP
DivX SUBTITLE
Depending on the DivX media, only those DivX Subtitles recorded on
the DivX media are available. The following are the available DivX subtitle
language format and their corresponding language coverage.
Western European: Albanian, Breton, Catalan, Danish, Dutch,
English, Faroese, Finnish, French, Gaelic, German, Icelandic, Irish, Italian,
Norwegian, Portuguese, Spanish and Swedish
Turkish: Albanian, Danish, Dutch, English, Finnish, French, Gaelic,
German, Italian, Kurdish (Latin), Norwegian, Portuguese, Spanish,
Swedish and Turkish
Central European: Albanian, Croat, Czech, Dutch, English, German,
Hungarian, Irish, Polish, Romanian, Slovak, Slovene and Serbian
Cyrillic: Bulgarian, Belorussian, English, Macedonian, Moldavian,
Russian, Serbian and Ukrainian
Greek: English and modern Greek
Hebrew: English and modern Hebrew
Arabic: Arabic
Baltic: Baltic
Vietnam: Vietnamese
Unicode: Default subtitle.
DEUTSCH
DivX REGISTRATION
The Registration code details necessary for VOD (Video-On- Demand) service
can be shown by pressing [ENTER] while at “DivX Registration” menu option.
OSD LANGUAGE
NEDERLANDS
SVENSKA
OSD (ON-SCREEN DISPLAY)
The OSD of VISO FIVE can be shown in eight different language versions
– English, French, German, Dutch, Spanish, Italian, Russian and Swedish.
Select the language setting you prefer.
РУССКИЙ
20
Downloaded From Disc-Player.com NAD Manuals
OPERATION
Depending on the media, the following are other basic features of the
VISO FIVE’s internal DVD player. Make sure that you select “DVD” at the Device
Selector selection of the HTR 7 before you proceed with the specific function.
TITLE AND MENU BUTTONS
REGION MANAGEMENT INFORMATION
There are two different disc sizes. Place the disc in the correct guide on the
disc tray. If the disc is out of the guide, it may damage the disc and cause
the VISO FIVE to malfunction. “DISC Err” appears on both the VISO FIVE’s
display and the TV/monitor screen, if the disc is placed upside down (and it
is a single sided disc).
The following are important tips when loading a disc
• Do not push the disc tray while it is moving. Doing so may cause the
VISO FIVE to malfunction
• Do not push up the disc tray or put any objects other than discs on the
disc tray. Doing so may cause the VISO FIVE to malfunction.
• Keep your fingers well clear of the disc tray as it is closing. Be especially
careful with children’s fingers around the closing disc tray, as there is a
risk of personal injury.
Press [TITLE] and a list of the titles on the disc are displayed. Depending
on the disc, pressing [TITLE] again will resume play from the scene when
[TITLE] was first pressed.
Press [ENTER], [PLAY] or the numeric button(s) to select desired title; the
selected title now starts playing.
Some DVDs have unique menu structures called DVD menus. For example,
DVDs programmed with complex contents provide guide menus, and
those recorded with various languages provide menus for audio and
subtitle language.
Press [MENU] during play; the DVD menu available on the disc is now
displayed. Pressing [MENU] again resumes play from the scene when MENU
was first pressed.
RANDOM
Press the HTR 7’s [STOP] key twice during playback to display an audio CD’s
total number of tracks and total playback time in the VFD.
After playing back all of the chapters in the title, VISO FIVE’s DVD player
automatically stops and returns to the menu screen.
Press the HTR 7’s RANDOM key during playback and “Random” briefly appears
on the upper line of the VFD. “Ran” will then be displayed in VFD alongside the
track number and playback time. Press [
/
] for random playback of
audio tracks. Press RANDOM again to return to normal playback.
For iPod songs, “Ran Song” or “Ran Album” will be displayed in the VFD as
applicable. “Ran Song” allows random playback of songs within an album or
playlist. On the other hand, “Ran Album” randomly plays all the songs in an
album. Afterwards, another album is randomly selected and also randomly
plays all the songs in this album.
РУССКИЙ
NoteS
• Do not move the VISO FIVE during playback. Doing so may damage the
disc and the VISO FIVE.
• The HTR 7 control keys [ ], [ ], [ ], [
/
/
/ ] and [ ] are not
punch-through function keys. To use them for disc playback purposes, make
sure that HTR 7’s DEVICE SELECTOR is set to “DVD”.
NEDERLANDS
Press [PLAY/PAUSE], the disc tray is automatically closed and playback
begins. Press the HTR 7’s navigation buttons and then press [ENTER] or press
the numeric button(s) to select the desired track (CD). Play of the selected
item now begins (Depending on the DVD disc or other disc media, some
operations may be different or restricted. Refer to the jacket or case of the
disc you are playing).
ITALIANO
DISC LOADING AND PLAYBACK
You can open the disc tray by pressing [OPEN/CLOSE] button even if the
VISO FIVE is in standby mode. The power indicator will turn from amber to
blue. Place a disc on the disc tray with the playback side down.
Both these buttons are only found on the HTR 7. The [TITLE] and [MENU]
buttons are used to display via OSD, the title headings and menus of the
DVD and other applicable media. Some movie discs may contain two or
more titles. If the disc has a title menu recorded on it, the [TITLE] button can
be used to select the movie title. (The details of operation differ depending
on the disc used.)
DEUTSCH
The VISO FIVE’s internal DVD Player is designed and manufactured to
respond to the Region Management Information that is recorded on a DVD
disc. If the Region number described on the DVD disc does not correspond
to the Region number shown on the back of the VISO FIVE, the internal DVD
player cannot play that disc. The VFD will display “REG Err” (“Wrong Region”
in the OSD) when an incompatible region disc is loaded.
ESPAÑOL
FRANÇAIS
Note
You cannot playback discs other than those listed above such as CDROM, CD-Extra, CD-G, photo-CD, and CD-i data discs. To do so may
render the VISO FIVE permanently inoperable.
SVENSKA
ABOUT THE VISO FIVE INTERNAL DVD PLAYER
The VISO FIVE has exceptional playability. It has support for DVD-Video,
DVD-R/-RW/+R/+RW, DVD-A, SVCD with or without PBC (Play Back Control),
VCD, DivX, Audio CD, CD-R/-RW and including recorded MP3, copyrightprotected WMA and JPEG files.
ENGLISH
using VISO FIVE – FEATURES
Downloaded From Disc-Player.com NAD Manuals
21
OPERATION
using VISO FIVE – FEATURES
ENGLISH
FRANÇAIS
REPEAT
ZOOM
To repeat the playback of a particular track, file or chapter, press the
VISO FIVE’s [REPEAT] key once. Pressing the same [REPEAT] key a second
time will repeat all the tracks, files or title. Turn off repeat mode by pressing
REPEAT button a third time.
Use [ZOOM] to enlarge the video image. Press [ZOOM] during playback or
still playback to activate the Zoom function. Depending on the media, each
press of the ZOOM button changes the TV screen in the following sequence:
ZOOM X 1, ZOOM X 2, and ZOOM X 3. Use the HTR 7 [
] keys to
move through the zoomed picture. To resume normal playback, press ZOOM
repeatedly until “ZOOM OFF”.
ESPAÑOL
Depending on your desired repeat mode, the following are shown or
highlighted in the VFD alongside the playback time display:
Rpt – Repeat track, file or song
RpA – Repeat all tracks, files or songs in an album or playlist
Rpf – Repeat MP3/WMA/JPEG folder
Blinking “T” – Repeat DVD title
Blinking “C” – Repeat DVD chapter
Blinking “G” – Repeat DVD-Audio group
Note
Zoom may not work on some DVDs.
PROGRAMMING
ITALIANO
SLOW
DEUTSCH
Press [SLOW
] during playback. The player will enter SLOW mode.
Repeatedly press [SLOW
] to select the desired speed. To exit Slow
Motion mode, press [PLAY].
STILL PICTURE AND FRAME-BY-FRAME PLAYBACK
NEDERLANDS
SVENSKA
Press [ ] (PAUSE) on the remote control or [PLAY/PAUSE] on the front panel
during playback. Advance the picture frame-by-frame by pressing [ ] on
the HTR 7 repeatedly. To exit still motion mode, press [ ] (PLAY).
The program function enables you to store your favorite tracks in the player
memory. When programming a sequence of tracks, the VISO FIVE must be in
stop mode. A program can contain up to 30 tracks. To program the sequence
1 Insert a disc.
Audio CD or MP3/WMA discs: CD or MP3/WMA menu appears.
2 Use [ ] to go “View Filter” - right pane of the menu screen.
3 Use [ ] to scroll down to “Prog Edit: Off”. Press [ENTER] to change
setting to “Prog Edit: On”. Press [ ] to check if you are at “View: Browser”
mode – if set to “View: Program” mode, press [ENTER] to switch to “View:
Browser” mode.
4 Press [ ] to go to the track selection on the left pane of the menu
screen. Select the track/file you want to add in your program list and
then press [ENTER] – a “ ✓ ” mark will appear to the left of the selected
track.
5 Press [ ] to go back to the right pane of the menu screen. Use [ ] to
scroll down to “Add to Program”; press [ENTER] to add the selected track
in your program list.
6 Repeat steps 4 and 5 to place additional tracks/files on the list.
7 Set “Prog Edit: On” to “Prog Edit: Off” in order to complete the
programming procedure - use [
] to scroll to “Prog Edit: On” and
then, press [ENTER] to change the setting to “Prog Edit: Off”.
NOTE
Program mode can also be switched to “Prog Edit: Off” or “Prog Edit: On”
by pressing the [PROGRAM] key of the HTR 7 remote control. Ensure that
the “DEVICE SELECTOR” setting of your HTR 7 is set to “DVD”.
РУССКИЙ
PROGRAM PLAYBACK
To begin playback, make sure that you are at “View: Program” mode as set
up from the “View Filter” section. Press [ ] (Play) to start program playback.
“Prg” will be displayed in the VFD alongside the track number during
program playback mode.
22
Downloaded From Disc-Player.com NAD Manuals
OPERATION
PLAYING MP3/WMA/JPEG
The VISO FIVE can play MP3/WMA formatted recordings on CD-R, or CD-RW
discs as well as view discs with JPEG files. You may mix any of the file types
on the disc.
Load the applicable disc. The OSD will display the folders or files as a list. Use
the HTR 7’s [
] keys to navigate through the folders or files. You must
be at stop mode to access folders on the left side of the menu window.
Press [ENTER] or [PLAY] to start playback. For each file type being played,
the file number is preceded by M”, “W” or “J” to indicate the file being played
is a MP3, WMA or JPEG file.
TIMER INDICATOR SETTINGS
If you have selected “ON TIME YES” and/or “OFF TIME YES”, a corresponding
color indicator will be illuminated in the upper left portion of the VFD –
GREEN indicates “ON TIME” setting is enabled; RED indicates that “OFF TIME”
setting is enabled. To directly turn off the enabled timer setting(s), toggle
TIMER ON/OFF button – the applicable color indicator is extinguished.
Toggle TIMER ON/OFF button again to enable your timer settings – the
corresponding color indicator is illuminated again.
FRANÇAIS
ESPAÑOL
RESUME NORMAL PLAYBACK
Make sure that you are at “View: Browser” as set up from the “View Filter”
section. Press [ ] to go to the left pane of the menu screen. Press [ENTER]
or [ ] (Play) to resume normal playback.
ITALIANO
NOTES
• Instead of selecting “Clear Program”, a programmed track can also be
directly deleted by pressing the [CLEAR] key of the HTR 7 remote control.
Ensure that the “DEVICE SELECTOR” setting of your HTR 7 is set to “DVD”.
• To delete more than one or all programmed tracks, select the tracks one
by one by pressing [ENTER] each time. All tracks with “ ✓ ” mark will be
deleted when [CLEAR] button is pressed (or “Clear Program” is selected).
TIMER SETUP
The following are the steps on how to setup the internal clock of the
VISO FIVE, setup the time you wish the VISO FIVE to be switched ON from
standby mode (ON TIME) or go to standby mode OFF (OFF TIME).
1 Press and hold the front panel [TIMER ON/OFF] button for more than
4 seconds. “TIME” is displayed in the VFD along with the current clock
settings – the “hour” value is blinking.
2 Use the [PRESET
/
] buttons to change the “hour” setting.
3 Press [MEMORY] button to move on to “minute” setting – the “minute” value is
blinking. Use the [PRESET
/
] buttons to change the “minute” setting.
4 Press [MEMORY] button to move on to “ON TIME” setting. Follow steps 2
and 3 above to setup your preferred ON TIME “hour” and “minute” settings.
5 Press [MEMORY] button to complete your “ON TIME” settings. “ON TIME
YES” will be displayed in the VFD. Use [PRESET
/
] buttons to
toggle between “ON TIME YES” and “ON TIME NO”.
6 Press [MEMORY] button to select either “ON TIME YES” to enable the “ON
TIME” settings you have set up or “ON TIME NO” if you do not want to
enable your “ON TIME” settings.
7 “OFF TIME” is also setup the same way as that of “ON TIME”.
AUTOMATIC POWER OFF FUNCTION
When at DVD mode, the VISO FIVE will automatically shut down and go to
standby mode if it is left at “NO DISC” status for 8 minutes.
DEUTSCH
ERASING A TRACK FROM PROGRAM LIST
To erase a track from the program list, make sure that you are at “View:
Program” and “Prog Edit: On” as set up from the “View Filter” section.
1 Press [ ] to go to the left pane of the menu screen.
2 Select the track you wish to erase from the program list. Press [ENTER].
3 Press [ ] to go to the right pane of the menu screen. Use [ ] to scroll
down to “Clear Program”. Press [ENTER] – the selected programmed
track is deleted.
ENGLISH
using VISO FIVE – FEATURES
РУССКИЙ
SVENSKA
NEDERLANDS
ROTATE PICTURE
Press [
] keys during the showing of a picture to rotate the picture
90°, 180°, 270° and back to “No rotation” (original normal position).
Downloaded From Disc-Player.com NAD Manuals
23
Operation
USING THE VISO FIVE - AM/FM/DB/iPod
ENGLISH
LISTENING TO AM/FM RADIO
SETTING RADIO PRESET
The VISO FIVE’s internal AM/FM tuner offers very high quality sound
from radio broadcasts. The reception and sound quality will always be
dependent to a degree however on the type of antenna(s) used as well as
proximity to the broadcast origin, geography and weather conditions.
The VISO FIVE can store as many as 60 (30 FM and 30 AM stations) of your
favorite radio stations for immediate recall.
1 To store a radio preset, first tune the desired frequency (see above), then
press the front panel [MEMORY] button. The VFD will show a blinking
“MEMORY” icon and the next available vacant Preset number.
2 Press [MEMORY] button again to store the desired frequency on the
Preset number shown or use the [
/
] keys to select another
available Preset number.
3 Then, press [MEMORY] key button again. Your desired frequency is now
stored in the assigned presets.
The Radio Presets must be stored from the front panel. This setup function
is not accessible from the HTR 7 remote control.
ABOUT ANTENNAS
FRANÇAIS
The supplied ribbon-wire FM antenna can be connected to the rear-panel
FM-antenna input using the included ‘balun’ adapter and should be fully
extended to form a “T”. This folded-dipole antenna will usually work best
when oriented vertically, with the arms of its “T” fully outstretched and
arranged perpendicular to the origin of the desired broadcast. There are
no ‘rules,’ however, and experimenting freely with antenna placement and
orientation may yield the clearest sound and lowest background noise.
ESPAÑOL
In areas of poor FM reception, an exterior FM antenna can improve
performance dramatically. If radio listening is important to you, consider
consulting an antenna installation professional to optimize your system.
The supplied AM ‘loop’ antenna will usually provide adequate reception.
However, an exterior AM antenna can be used to improve reception.
Consult an antenna professional for more information.
ASSEMBLING THE LOOP ANTENNA
Use the [
/
] keys on the front panel to step up or down between presets.
Press and hold [
/
] to “scroll” continuously up or down. The HTR 7 remote’s
[PRESET] keys work similarly. Empty presets will be skipped during preset tuning.
DIRECT RECALL OF A PRESET
You can directly recall a desired Preset number.
1 Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see
the lower line of the VFD). Select “Preset” mode.
2 Using the numeric keys of the remote control, directly key-in your
desired Preset number. For example, to enter Preset 5, press “5”.
ITALIANO
NOTE
Ensure that the “DEVICE SELECTOR” setting of your HTR 7 is set to “TUNER”.
DEUTSCH
1 Rotate the outer frame of the antenna.
2 Insert the bottom edge of the outer frame into the groove on the stand.
3 Extend the antenna cord.
SELECTING THE RADIO
To select the VISO FIVE’s tuner mode, rotate “INPUT SELECTOR” knob on the
front panel repeatedly until AM/FM mode or the HTR 7’s numeric ‘5’ while at
AMP device selector page.
NEDERLANDS
Press [TUNE
/
] on the front panel momentarily to step up or down
AM or FM frequencies.
Press and hold [TUNE
/
] for more than 2 seconds to search up or
down AM or FM frequencies - the VISO FIVE’s tuner will stop at the next
sufficiently strong signal it encounters. Pressing the [TUNE
/
]
during the search process will stop the search.
SVENSKA
DIRECT TUNING
If you know your desired station’s frequency allocation, you can tune
directly to the station.
1 Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see
the lower line of the VFD). Select “Tune” mode.
2 Using the numeric keys of the remote control, key-in the frequency
allocation of the station. For example, to enter 104.50MHz, press “1”, “0”,
“4”, “5” and “0” or press “”1”, “0”, “4” and “5”.
РУССКИЙ
NOTE
Ensure that the “DEVICE SELECTOR” setting of your HTR 7 is set to
“TUNER”.
24
Downloaded From Disc-Player.com NAD Manuals
AUTOMATIC PRESET
Preset stations may also be programmed automatically for the entire FM (or
AM) band.
1 Toggle the [AM/FM/DB] button to select FM (or AM) band.
2 Press and hold the [MEMORY} button until the station frequency
indication begins to increase.
3 Release the button and note that the tuner will search the entire FM (or
AM) band, and stop briefly at each station that has acceptable signal
strength. The VISO FIVE will automatically assign a preset number to
each station, and then search for the next station. Up to 30 of the best
received FM stations (or AM stations) will be automatically stored.
DELETING A STORED PRESET
You can empty a preset by deleting the stored information.
1 Select the preset number to be entered.
2 First press the [DISPLAY] button and hold it in. While holding in the
[DISPLAY] button, press the [MEMORY] button for about half a second,
then release the [MEMORY] button.
3 The preset will then be deleted and “DELETED” scrolls on the display.
4 To clear all the presets at the same time, repeat step 2 again but this
time do not release the [MEMORY] button. Hold down both buttons
until the current preset number shown in the VFD is extinguished. All
presets are now deleted.
Operation
ENTERING USER NAMES
To name a radio preset “NEWS”, follow the procedure as below (The buttons
mentioned apply to the front panel’s buttons).
1 Recall the desired radio preset.
2 Press and hold the [DISPLAY] button and then within five (5) seconds,
use the [PRESET
/
] buttons to select the first character of the
name (“N” from the alphabetical list).
3 Press [TUNE
] button to select the character and correspondingly
move forward to the next position. (Press [TUNE
] to go back to the
previous character). Repeat this process for each character in sequence.
4 Press the [MEMORY] key to store the User Name and exit the text-entry
mode.
ABOUT RDS
The Radio Data System (RDS) permits compatible tuners to display text
determined by the broadcaster. The VISO FIVE supports two RDS modes,
station-name (PS mode) and radio-text (RT mode). However, not every FM
station incorporates RDS in its broadcast signal. In most areas you will find
from one to several RDS-enabled stations, but it is by no means impossible
that your favorite stations will not be broadcasting RDS data.
CONNECTING THE DAB MODULE
Plug-in the other end of the DIN connector (supplied with your NAD DAB
Adaptor DB 1) from the DAB module’s output port into the corresponding DAB
module input socket on the rear panel of the VISO FIVE. Select DAB mode on
the VISO FIVE by toggling the [AM/FM/DB] button in the front panel.
NOTES
• Please refer to NAD DAB Adaptor DB 1 installation guide for proper setup
connection of the DB1 with respect to the VISO FIVE.
• The front panel [TUNER MODE] and [MENU] buttons function the
same way at DAB mode. The [MENU/TUNER MODE] key of HTR 7 is the
equivalent button for both functions.
• If there is no NAD DAB Adaptor DB 1 connected at the corresponding DAB
input terminal at the rear panel, the VFD will show “CHECK DAB TUNER”.
ITALIANO
ABOUT USER NAMES
You can assign an eight character “User Name” to each radio preset, which
will show in the front-panel readout whenever that preset is recalled.
With DAB, the listener can scroll through a list of available stations - then
instantly tune to the station of his choice. There is no need either to
remember channel frequencies. All broadcasts are selected by simply
selecting the service name.
The VISO FIVE makes it possible for you to enjoy listening to DAB broadcasts.
The VISO FIVE has a Digital Audio Broadcast (DAB) module socket on the
rear panel for adding a separately sold and NAD-specified outboard DAB
module – the NAD DAB Adaptor DB 1. All the control software for this
format is included; just plug-in the module and start enjoying the CD-like
quality sound and expansive content selection available with DAB.
DEUTSCH
NOTE
In FM/XM/DAB mode, [MENU] button functions the same way as the
[TUNER MODE] button.
FRANÇAIS
ABOUT DAB RADIO
Until now, analogue radio signals such as FM or AM have been subject to
numerous kinds of interference on their way from the transmitter to your
radio. These problems were caused by mountains, high-rise buildings
and weather conditions. With Digital Audio Broadcast (DAB), you can now
receive CD-like quality radio programs without any annoying interference
and signal distortion. DAB broadcasts use digital signals rather than
traditional analogue transmissions, thus providing clear high quality
reception. You get far more robust reception and virtually hiss or crackle
free sound with DAB as long as you are within a good coverage area.
ESPAÑOL
CHOOSING TUNER MODE
The front-panel [TUNER MODE] key is a dual-purpose control. In the normal
position, “FM STEREO” and “FM MUTE” icons on the VFD are lit; only the stations
with a strong signal can be listened to, and the noise between stations is muted.
Pressing the [TUNER MODE] button again (“FM STEREO” and “FM MUTE”
icons on the VFD are extinguished) allows distant and potentially noisy
stations to be received. Noise is reduced if the FM station signal level is less
than the FM Stereo threshold (since mono FM is inherently less noiseprone) though at the sacrifice of the stereo effect.
ENGLISH
USING THE VISO FIVE - AM/FM/DB/iPod
VIEWING RDS TEXT
NEDERLANDS
When an RDS-enabled FM broadcast is tuned, after a brief delay the “RDS” icon
will light in the VISO FIVE’s front panel readout and the readout’s character
section will show its station-name (PS) text: “ROCK101,”for example.
РУССКИЙ
SVENSKA
Press the front panel [DISPLAY] key to toggle the readout between this
and the station’s radio-text (RT) readout, if any, which might scroll song- or
artist-name or any other text of the station’s choosing.
Downloaded From Disc-Player.com NAD Manuals
25
Operation
USING THE VISO FIVE - AM/FM/DB/iPod
ENGLISH
FRANÇAIS
ESPAÑOL
DAB OPERATION
PRESET TUNE
With the separately sold NAD DAB Adaptor DB1 already connected to the
VISO FIVE, you can now carry out the VISO FIVE to receive DAB broadcasts.
1 Toggle [AM/FM/DB] button until DAB mode. When DAB mode is selected,
VFD will show “DAB initialize – Please wait” and then go to “Full Scan” mode.
FULL SCAN will enable the scanning of the full range of digital frequencies
(Band III and L-Band). This sequence cannot be interrupted.
The arrows show the progress of the sequence. When scanning is
completed, the last number shown on the upper right side of the VFD
corresponds to the total number of DAB broadcast stations found. Then,
the first station is tuned in (See “ALPHANUMERIC” description below to
understand the order or arrangement of stations).
2 The strength of the incoming signal can be shown on the VFD by
pressing the [ENTER] button. The more “o” segments visible in the lower
display line, the stronger the signal. By changing the position of the
antenna, you can increase the signal strength. Consult an antenna
professional for more information.
Use this option to select a DAB preset station.
1 While listening to a DAB broadcast, press front panel’s [MENU] button
and then [TUNE
/
] to select “Preset tune”. Press [ENTER].
2 Press [TUNE
/
] to step up or down between presets. Note that
Presets must have been previously stored.
3 Press [ENTER] to select desired preset number.
ITALIANO
NOTES
• “No stations Available” will be shown in the VFD when no DAB stations
are found after the scanning process. If this occurs, check the connection
and position of the DAB antenna or call your local DAB broadcast
providers for coverage information.
• When using HTR 7 buttons to navigate DAB options, ensure that the
“DEVICE SELECTOR” setting of your HTR 7 is set to “TUNER”.
SERVICE LIST
Follow the steps below to select through the DAB service stations found.
1 At DAB mode, press [TUNE
/
] to step through the list of
available stations as shown in the lower display line of the VFD.
2 Press [ENTER] to select the desired station.
DAB TUNER MODE
DEUTSCH
Aside from “Full Scan” as already described above, pressing the [MENU]
button will also present you with other options namely - Local Scan, Preset
Tune, Station Order, Tune Aid, Dynamic Range and Prune List
LOCAL SCAN
NEDERLANDS
LOCAL SCAN performs local scanning of available DAB services in your area.
Check with your dealer or visit www.WorldDAB.org to check the applicable
digital transmission frequencies in your area.
1 While listening to a DAB broadcast, press front panel’s [MENU] button
and then [TUNE
/
] to select “Local scan”. Press [ENTER].
2 Local scan of available DAB services in your area will start. The arrows
show the progress of the sequence. When scanning is completed, the
last number shown on the right side of the VFD corresponds to the total
number of DAB broadcast stations found. Then, the first station is tuned in.
SETTING DAB PRESETS
The VISO FIVE can store as many as 99 DAB stations of your favorite DAB
broadcast for immediate recall.
1 To store a DAB preset, first tune the DAB broadcast, and then press the
front panel [MEMORY] button. The VFD will show a “Preset Memory”
and the next available vacant Preset number (the number is blinking).
2 Press [MEMORY] button again to store the desired DAB broadcast on
the Preset number shown or use the [TUNE
/
] keys to select
another available Preset number.
3 Then, press [MEMORY] key button again. Your desired DAB broadcast is
now stored in the assigned presets.
STATION ORDER
Use “Station order” to sort the sequence of the listed stations. There are four
orders – Alphanumeric, Active, Ensemble and Favourite.
1 While listening to a DAB broadcast, press front panel’s [MENU] button
and then [TUNE
/
] to select “Station Order”. Press [ENTER].
2 Toggle [TUNE
/
] to select through “Alphanumeric”, “Active”,
“Ensemble” and “Favourite”.
3 Press [ENTER] to select desired station order.
ALPHANUMERIC
This is the default setting. Stations are arranged by numbers first and then
alphabetically by letters.
ACTIVE
Active stations are listed at the top of the channel list. Those channels
that are in list but have no service in the area will be displayed last in the
channel list.
ENSEMBLE
Digital radio is broadcast as groups of data called ensemble. Each ensemble
contains a number of stations, transmitted at a set frequency. When
“Ensemble” is selected as the mode of station order, the radio stations are
arranged in the order of their ensemble names.
NOTE
Ensemble is also interchangeably termed as “multiplex” by other
broadcast providers.
SVENSKA
FAVOURITE
The VISO FIVE memorizes the top ten stations you listen as you tune in
stations. They will be listed at the top of the channel list.
РУССКИЙ
26
Downloaded From Disc-Player.com NAD Manuals
Operation
DYNAMIC RANGE
INFORMATION SETTINGS
The level of compression of stations can be set to eliminate the differences in
dynamic range or sound level between radio stations. Popular music would
normally be more compressed than classical music, resulting in possible
different audio levels when changing from one station to the other. Setting the
Dynamic Range to “D-Range 0” means no compression, “D-Range 1/2” indicates
medium compression and “D-Range 1” shows maximum compression. No
compression is recommended, especially for classical music.
1 While listening to a DAB broadcast, press front panel’s [MENU] button
and then [TUNE
/
] to select “Dynamic range”. Press [ENTER].
2 Toggle [TUNE
/
] to select through “D-Range 0”, “D-Range
½”and “D-Range 1”. The upper line display shows the current dynamic
range setting while the lower line display will show the choices for the
dynamic range values.
3 Press [ENTER] to select desired Dynamic Range level.
While listening to a DAB broadcast, the type of information displayed in the
lower line of the VFD can be varied. Toggle front panel’s [DISPLAY] button
to step through the following display options:
NOTE
The number of ensembles and stations that could be scanned will vary
depending on your location.
PRUNE LIST
FRANÇAIS
Time and Date
Audio Signal information
Channel and frequency
Software version
Program type
This is a description of the type of broadcast supplied by the station, such
as Pop, Rock, Drama and the likes.
ITALIANO
Station Name
The name or identification of the DAB broadcast station is shown.
ESPAÑOL
Signal Q
Time and date
The current time and date as supplied by the DAB station are displayed.
Audio Signal Information
Displays the bit rate and audio type (stereo, mono or joint stereo)
as transmitted by the DAB broadcast provider. These are set by the
broadcaster to suit the type and quality of material being transmitted.
Channel and frequency
The channel and frequency of the currently tuned DAB broadcast are
displayed.
Signal Quality
This displays the digital error rate (0 to 99) of the currently tuned channel
- the lower the figure, the better the quality of the received broadcast.
Software version
Show the version number of the installed software.
РУССКИЙ
SVENSKA
There maybe situations wherein certain stations become inactive. The
“Prune List” option enables the deletion of these inactive stations in the
service list.
1 While listening to a DAB broadcast, press front panel’s [MENU] button
and then [TUNE
/
] to select “Prune List”.
2 Press [ENTER]. Use [TUNE
/
] and then press [ENTER] to select
between “Cancel” or “OK? [SELECT]”. Any inactive stations (normally
stations preceded by a “?” mark) are automatically deleted when “OK?
[SELECT]” is selected. Otherwise, select “Cancel”.
Station Name
DEUTSCH
This option allows you to directly tune to a desired channel and include it in the
service list (if not yet available at the time). You can also use TUNE AID to assist
you in positioning the DAB antenna for best reception of the desired channel.
1 While listening to a DAB broadcast, press front panel’s [MENU] button
and then [TUNE
/
] to select “Tune aid”. Press [ENTER]. The
current channel and frequency are shown in the lower line of the VFD.
The number of “o” displays at the upper line of the VFD indicates the
signal strength level of the current channel.
2 To select other channels, toggle [TUNE
/
] to step through the
channel list. Release [TUNE
/
] when you have arrived at your
desired channel. To improve the reception of the selected channel, adjust
or reposition the DAB antenna until the best reception is indicated.
3 Press [ENTER] to tune the selected channel.
Program Type
NEDERLANDS
TUNE AID
ENGLISH
USING THE VISO FIVE - AM/FM/DB/iPod
Downloaded From Disc-Player.com NAD Manuals
27
Operation
USING THE VISO FIVE - AM/FM/DB/iPod
ENGLISH
ABOUT XM RADIO
The VISO FIVE is “XM Ready” which means that with the addition of separately
sold XM Mini-Tuner CPC-9000 and XM Mini-Tuner Home Dock, it has everything
you need to listen to live XM. Everything else is built right in. Just subscribe to
the XM service and your VISO FIVE will be ready to receive XM content.
FRANÇAIS
NOTES
• Questions? Visit www.xmradio.com
Listeners can subscribe by visiting XM on the Web at www.xmradio.com
or by calling (at the time of printing this manual) XM’s Listener Care at
(800) 853 9696. Be ready with your Radio ID that can be found on the
radio by selecting Channel 0.
• Check with your NAD audio specialist for other versions of XM MiniTuner compatible with VISO FIVE.
ESPAÑOL
CONNECTING THE XM ANTENNA
Plug the end of the XM antenna into the corresponding XM antenna port
on the rear panel of the VISO FIVE. Press and hold [DISPLAY] button on the
front panel to check the current XM channel’s signal strength as shown in
the VFD. Press and hold [DISPLAY] again to exit signal strength check.
ITALIANO
NOTES
• Refer also to your XM radio’s guide on how to install the XM antenna for
optimum signal reception.
• The front panel [TUNER MODE] and [MENU] buttons function the
same way at XM mode. The [MENU/TUNER MODE] key of HTR 7 is the
equivalent button for both functions.
• When using these HTR 7 buttons to navigate XM menu options, ensure
that the “DEVICE SELECTOR” setting of your HTR 7 is set to “TUNER”.
• If there is no XM tuner connected at the corresponding XM input
terminal at the rear panel, the VFD will show “CHECK XM TUNER”.
DEUTSCH
TUNING STATIONS
There are three ways to tune to the XM channel you wish to listen. Make
sure to set your HTR 7’s “DEVICE SELECTOR” to “TUNER” prior to undertaking
the following tuning options.
1ALL CH SEARCH (All Channel Search): Toggle front panel’s [MENU]
button to select “ALL CH SEARCH”. Use the front panel or HTR 7’s [
] [ or
TUNE
/
/
/
] buttons to step up or down each available XM
channel. Press and hold [
] for faster scanning of XM channels.
NEDERLANDS
SVENSKA
2CATEGORY SEARCH: The XM channels are grouped into categories for
easier selection of desired genre.
a Toggle front panel’s [MENU] button to select “CATEGORY SEARCH”.
“CATXM” and a corresponding category is displayed in the VFD.
“CATXM” stands for categories the channels are grouped into – i.e.,
Country, Rock, Jazz & Blues, etc.
b Use HTR 7’s [
] (or front panel’s [PRESET
/
]) buttons to
step up or down the available categories.
c Press HTR 7’s [
] (or front panel’s [TUNE
/
]) buttons
to select through the available XM channels within the selected
category. You can also use HTR 7’s [TUNE
/
/
/
]
buttons. Tuning will only be limited to within the selected category.
d Repeat “b” above to choose another category.
3PRESET SEARCH: Toggle front panel’s [MENU] button to select “PRESET
SEARCH”. At this menu option, a stored preset can be directly recalled
by entering the preset number using the HTR 7’s numeric buttons.
РУССКИЙ
28
Downloaded From Disc-Player.com NAD Manuals
DIRECT CHANNEL CALL
While at either “CATEGORY SEARCH” or “ALL CH SEARCH” mode, a desired
XM channel can be directly tuned in by using the HTR 7’s numeric buttons.
To key-in XM channels that are less the 3 digits, press “0” in place of the digit
or press [ENTER] after entering the XM channel number. For example, to
enter XM channel 8, press “0”, “0” and “8” or press “8” then [ENTER].
VIEW XM INFORMATION
Toggle [DISPLAY] button to display the XM information of the selected
channel such as the XM channel category, XM station name, artist name,
song title or any other text as supplied for the channel.
SETTING XM PRESETS
The procedure for storing XM channels is the same method as stated in the
section “SETTING RADIO PRESETS” under “LISTENING TO AM/FM RADIO”. You
can store up to 30 XM channels.
For immediate recall of stored XM presets, press the front panel’s [PRESET
/
] button or HTR 7’s [PRESET
] keys to step up or down the
stored XM channel presets.
ABOUT THE iPod INPUT FEATURE
The VISO FIVE is equipped with a data port in the rear panel where an
optional “NAD IPD 1 Dock with iPod” (NAD IPD 1) can be plugged in.
With the NAD IPD 1 linking the VISO FIVE with your own iPod player, you
can enjoy listening to your favorite tracks and playlists, as well as view
applicable still image and video playback.
You can control your iPod player using the assigned buttons in the
VISO FIVE front panel. And with the corresponding HTR 7 remote control
function keys, you can select the materials stored in your iPod for playback
as well as access many of its functions even from across the room. The
optional NAD IPD 1 also charges your iPod player while it is connected to
the VISO FIVE.
NOTES
• NAD IPD 1 and iPod player are optional and not supplied with your
VISO FIVE.
• iPod player functions, features and playback capabilities accessible
through VISO FIVE may vary depending on your iPod player model.
• When using the HTR 7 to control the iPod functions, make sure that the
Device Selector is set to “MP DOCK”.
CONNECTING THE OPTIONAL “NAD IPD 1 Dock with iPod” and iPod PLAYER TO THE VISO FIVE
Make sure that all the devices are unplugged before making the connections.
1 Connect the NAD IPD 1’s plug into the VISO FIVE’s “MP DOCK” data port.
2 Connect also the NAD IPD 1’s S-video and audio out to the VISO FIVE
VCR input (the default iPod source allocation in the VISO FIVE).
3 Dock your iPod player into the NAD IPD 1.
4 After linking together your iPod player, NAD IPD 1 and the VISO FIVE,
you can now plug them IN to their applicable power sources.
5 With your iPod player, NAD IPD 1 and VISO FIVE all at power ON state,
rotate INPUT SELECTOR knob to select “iPod” source. The upper line of
the VFD will show “iPod”.
NOTE
When the iPod player is removed from NAD IPD 1, the lower line of the
VFD will briefly show “Disconnected”. Dock your iPod player into the
NAD IPD 1 and the lower line will briefly show “Connected”.
Operation
NOTE
At “Menu mode”, your docked iPod player’s click wheel and controls will
not be operational. Your iPod player will show in its display the NAD
logo. Use the corresponding front panel or HTR 7 buttons to navigate
through the “Menu mode” options.
SIMPLE MODE
At “Simple mode”, refer to your docked iPod player’s own display screen
to navigate and make full use of its features. Use your docked iPod’s own
click wheel and controls or the corresponding front panel or HTR 7 buttons
to select through the available options as displayed in your iPod player’s
display screen.
CONTROL FEATURES
Use the following control buttons in navigating through the iPod menu
options. These are applicable using either the front panel or HTR 7 buttons.
Since the HTR 7 will be the primary controller in most cases, we will focus
on remote-controlled operations.
]
FRANÇAIS
TUNE [
/
]
During playback or PAUSE mode, press and hold [TUNE
/
for fast forward or backward scanning of current song.
Press [TUNE
] to skip forward to the next song or [TUNE
to skip back to the previous song. The equivalent front panel key for
[TUNE
/
] is [SCAN
/
].
]
PAUSE [ ] / PLAY [ ]
Press PAUSE [ ] during playback to stop playback temporarily. Resume play
by pressing PAUSE [ ] again or PLAY [ ].
NOTE
For other navigation functions, please refer to your iPod player’s owner’s
manual. Depending on the iPod player model, some other functions
maybe controlled using the applicable VISO FIVE navigation controls.
TO VIEW VIDEOS OR PHOTOS LOADED IN YOUR iPod
Videos or photos uploaded in your iPod can be viewed directly via the VISO
FIVE. The following are the steps
1 Make sure that the “TV Out” setting of your iPod’s Video or Photo
Settings menu is at “On” mode and appropriate “TV Signal” is chosen.
2 Video or photo file selection and playback procedures are managed
directly from your iPod player or at “Simple Mode”.
3 With the iPod (IPD 1) dock’s S-VIDEO OUT and AUDIO OUT ports
connected to the VISO FIVE’s VCR input or to any other assignable input,
you can now directly enjoy via VISO FIVE your video or photo selections
as uploaded in your iPod. Make sure that you select the correct source
input of the VISO FIVE.
NOTE
iPod player functions, features and playback capabilities accessible through
VISO FIVE may vary depending on your iPod player model. Check NAD IPD1’s specifications with regards to specific iPod models it supports.
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
SVENSKA
DISP
During playback, toggle [DISP] key of HTR 7 to show in the VFD lower line
the following
· Elapsed time and remaining playback time of the current song
· Song title
· Artist Name
· Album title
ESPAÑOL
MENU MODE
At “Menu mode”, there are several menu options available that are similar to
what you can find in an iPod player. During playback, press [MENU] and you
will be directed to the “Playlists” option of the “Menu mode”. Use the HTR 7’s
[
] (or front panel’s [PRESET
/
] buttons) to select through
other “Menu mode” options like Artists, Albums, Songs, Podcasts, Genres,
Composers and Audiobook. Using the corresponding front panel or HTR 7
buttons, navigate and select through these VFD “Menu mode” options as
you would when operating your iPod player independently.
ENTER
Press [ENTER] to select an option or start playback when applicable.
ITALIANO
“Menu mode” is the default menu option. The following is the procedure to
switch between “Menu mode” and “Simple mode” options
1 Press and hold front panel’s [MENU] button (or [MENU/TUNER MODE]
key of HTR 7) for about 3 seconds and then release the button.
2 “Menu mode” or “Simple mode” will appear. You are at “Menu mode” if
the lower line of the VFD briefly shows “Connected” and then switches
to display the elapsed time and remaining playback time of the current
song. You are at “Simple mode” if the lower line of the VFD shows
the current listening mode, i.e. PLII Music. Select your preference by
releasing the button when the mode you desire appears.
[
] NAVIGATION BUTTONS
While at menu options or selection lists, toggle [
] to go up or down
the options, lists or song titles. Press and hold [
] to quickly scroll
through the song titles. The equivalent front panel key for [
] is
[PRESET
/
].
DEUTSCH
There are two menu options for iPod – Menu mode and Simple mode. At
“Menu mode”, iPod navigation will be done and guided through the VFD
of the VISO FIVE. At “Simple mode” everything will be guided through your
iPod’s own display screen as you would do in normal iPod use.
NEDERLANDS
iPod MENU OPTIONS
ENGLISH
USING THE VISO FIVE - AM/FM/DB/iPod
If there is no information available, the display will show “ARTIST: Unknown
Artist” or “ALBUM: Unknown Album” as applicable.
РУССКИЙ
The equivalent front panel key for [DISP] is [DISPLAY].
MENU
Press [MENU] to return to a previous option or menu selection.
Downloaded From Disc-Player.com NAD Manuals
29
Operation
USING THE HTR 7 REMOTE CONTROL
ENGLISH
SPECIFICATIONS
FRANÇAIS
•
•
•
•
•
•
•
•
Controls up to 8 devices.
44 function keys.
Learns up to 352 commands.
Records up to 44 macros with a maximum of 64 commands each.
Configurable punch-through.
Key illumination with programmable timeout.
Upgradable.
Contains pre-programmed library of NAD remote codes.
The NAD HTR 7 is ready to operate the VISO FIVE right out of the box, but it is really eight remotes in
one. Each of the 8 Device Selector keys at the top of the handset can call up a new “page” of remote
control codes to be transmitted by the remaining 44 keys. You may “teach” codes from any infraredremote controlled component, regardless of brand, to any or all of these.
ESPAÑOL
Obviously, the most logical system is that you teach the codes from your DVD player to the [DVD]
Device Selector “page,” your television’s codes to the [TV] “page,” and so on, but there is no required
scheme: You may load any commands to any key on any page (see “Learning Codes From Other
Remotes,” below).
ITALIANO
The HTR 7 is already preprogrammed with a full complement of commands for the VISO FIVE on
its [AMP] Device Selector page, and as well as with library commands to operate most NAD-brand
DVD or CD components on the corresponding Device Selector “pages.” These default commands are
permanent: Even if you teach the HTR 7 new commands to take their place, the underlying library
commands remain in place and can easily be recalled should you add an NAD component to your
system later (see “Delete Mode”, below).
NOTE
For use with the VISO FIVE, it should not be necessary to re-program any keys on the HTR 7 [AMP]
page. However, in order for the HTR 7 to control your specific NAD-brand components you may
need to load one or more different code-libraries (see “Loading Code Libraries,” below).
CONTROLLING THE VISO FIVE
DEUTSCH
The HTR 7 is divided into two main sections. Eight Device Selector keys at the top—[AMP], [DVD],
[TV] and so on—set the handset’s remaining keys to a “page” of commands to control a particular
component. A Device Select key determines only what component the HTR 7 will command; it does
not perform any function on the VISO FIVE. All of the remaining keys are function keys that can “learn”
control codes from virtually any infrared remote controller, allowing you to teach the codes of your
equipment, regardless of brand, to the HTR 7.
NEDERLANDS
However, the HTR 7 is already preprogrammed to operate the VISO FIVE. All of the function keys on the
[AMP] Device Selector “page” perform VISO FIVE functions. (The HTR 7 can also command many other
NAD components, from its [DVD], [CD], [TUNER] and [CUSTOM] pages.)
SVENSKA
It is important to note that certain HTR 7 keys perform different functions depending on the selected
Device Selector “page.” The color of the Device Selector key-labeling corresponds to the labeling of
the function keys. Most centrally, the orange [AMP] Device Selector “page” corresponds to the orange
input-select labeling above the numeric keys: When the HTR 7’s [AMP] Device Selector page is active,
these keys select the Viso Five inputs. Similarly, the purple [DVD] Device Selector “page” corresponds to
several purple labels, the green [TV] page to green labels, and so on.
SELECTING SOURCES
To directly switch or select sources using the HTR 7, set first your DEVICE SELECTOR to “AMP”. Press
the corresponding numeric key of the source you want to select (the orange label directly above
the appropriate numeric keypad is the Source allocated for such key). For example, press “2” to select
“Cable/Sat” source mode, “1” to switch to “DVD” mode and so on.
РУССКИЙ
30
Downloaded From Disc-Player.com NAD Manuals
Operation
Note
The HTR 7’s [VOL] keys are pre-programmed as “punched-through”
for all Device Select pages: [VOL] will operate the VISO FIVE’s volume
regardless of the currently selected device. The [SUB] level control is
similarly pre-programmed as punched-through.
To set a punch through, after entering the Learning Mode, and pressing the
desired key to be punched through, simply press the device key twice of
the device to punch through to. The status LED will turn green; press the
Device Selector key again to exit Learning Mode.
Example: Punch-through AMP [SURR MODE] key to the DVD “page”
• On the HTR 7, simultaneously press-and-hold [DVD] and [ ]; the Learn
LED turns steady green.
• Press [SURR MODE]; the Learn LED turns amber.
• Press [AMP] twice; the Learn LED turns green.
• Press [DVD] again to exit the learning mode.
NOTE
The HTR 7 control keys [ ], [ ], [ ], [
/
/
/ ] and [ ] are not
punch-through function keys. To use them for disc playback purposes, make
sure that HTR 7’s DEVICE SELECTOR is set to “DVD”.
Note
Macros are independent of the currently selected device.
RECORDING MACROS
To record a macro, simultaneously press-and-hold for 3 seconds both the
[MACRO] key and the HTR 7 function key to which you wish to assign the
macro, until the status LED turns green. The macro button will also light up.
Press the sequence of function keys to be recorded into the macro, being
sure to first press the requisite Device Selector key for each function (you
may switch devices while recording the macro as many times as necessary),
allowing you to create macro containing commands from more than one
Device Selector “page.”
When you have finished entering the desired command sequence, press
[MACRO] again to store the macro; the Learn LED and [MACRO] key
illumination will turn off.
ITALIANO
Note
Each macro can store a maximum of 64 command steps. If you exceed
this number, the macro will be stored automatically after the 64th
command is added.
Example: Record a Macro to the [0] key to Turn on the VISO FIVE, Select the
DVD Input, and Commence Playback:
• On the HTR 7, simultaneously press-and-hold [MACRO] and [0] (numeric
zero); the Learn LED turns steady green.
• Press [AMP]; press [ON]; press [1] (“DVD”); press [DVD]; press [ ] (Play)
- the Learn LED blinks as each step is added.
• Press [MACRO] again to exit the macro-record mode.
To clear a macro, perform the above steps without entering any functions.
Downloaded From Disc-Player.com NAD Manuals
DEUTSCH
PUNCH-THROUGH
The HTR 7’s “punch-through” function allows you to retain a function key
from one Device Select “page” to another, so that, for example, the AMP
[SURR MODE] function might still control the VISO FIVE when the DVD
Device Selector page is active.
MACRO COMMANDS
A “macro” command is a series of two or more remote codes issued
automatically from a single keypress. You might use a macro to automate
a simple command sequence, such as, “Turn on the DVD player” and
then press “play”. Or you might compose an elaborate macro to power
up an entire system, select a source, choose a Listening Mode, and begin
playback—again, all from a single keypress. The HTR 7 can store one macro
on each of its function keys (these exclude the Device Selector keys).
NEDERLANDS
Example: Learning “DVD Pause”
Position the HTR 7 and your DVD player’s remote as described above.
• On the HTR 7, simultaneously press-and-hold [DVD] and [ ]; the Learn
LED turns steady green.
• Press the HTR 7’s [ ] key; the Learn LED turns amber.
• Press-and-hold the DVD player’s remote’s pause key; the HTR 7’s Learn
LED flickers amber and then turns solid green. The command is learned.
• Press [DVD] again to exit the learning mode.
SVENSKA
Cancel Operation
You can cancel configuring a key, by pressing the active Device Selector key
before the learn process is complete; the Learn LED will turn red.
Note
The copy and punch-through functions are similar. However, if you
copy a command and then subsequently delete, or over-write the
original (source-key) command , the copied-to key’s command remains
unchanged. If you punch-through to a command and then delete or
over-write the original key, the punched-through functions also change
accordingly.
РУССКИЙ
If the Learn LED does not flicker amber you may need to vary the distance
between the remotes. If the Learn LED turns red rather than green, that
particular command of that source remote command could not be learned.
Example: Copy the Pause command from the CD page to the AMP [ ]
key:
• On the HTR 7, simultaneously press-and-hold [AMP] and [ ]; the Learn
LED turns steady green.
• Press [ ] (pause); the Learn LED turns amber.
• Press [CD]; press [ ] (pause); the Learn LED turns green.
• Press [AMP] again to exit the learning mode.
FRANÇAIS
COPY COMMAND FROM ANOTHER BUTTON
You may copy a command from any HTR 7 key to any other key. To copy a key
function, after entering the Learning Mode, and pressing the desired key to be
copied to, simply press the device key from which you wish to copy, having first
pressed its Device Selector key if it resides on another “page.” The status LED will
turn green; press the Device Selector key again to exit Learning Mode.
ESPAÑOL
LEARNING CODES FROM OTHER REMOTES
Begin by positioning the HTR 7 “nose-to-nose” with the source remote so
the two devices’ infrared windows are about 2 inches apart.
• Enter Learning Mode: On the HTR 7, simultaneously press-and-hold for
3 seconds both a Device Selector key and the [ ] key until the Learn
LED at the center of the HTR 7 turns steady green.
• Press the HTR 7’s function key you wish to teach a command; the Learn
LED will turn amber.
• Press-and-hold the function key on the source remote: The HTR 7’s
Learn LED will flicker amber for a second or two, then turn solid green.
The command is learned.
• Press the HTR 7’s Device Selector key again to exit the learning mode.
ENGLISH
USING THE HTR 7 REMOTE CONTROL
31
Operation
USING THE HTR 7 REMOTE CONTROL
ENGLISH
Executing Macros
To execute a macro, press and release [MACRO]; its key illumination lights
for 5 seconds. While it remains lit, press an HTR 7 key to which a macro has
previously been stored.
FRANÇAIS
The corresponding macro will run; as each step executes, its “parent” Device
Selector’s key flashes lights briefly; when execution is finished, the [MACRO]
key illumination goes out. Pressing any other HTR 7 key while a macro is
executing will abort the macro. Remember that you must hold the HTR 7 so
that its infrared emitter can activate the target components.
ESPAÑOL
Note
When a macro executes, a 1 second delay is automatically inserted
between its commands. If you need more than a 1 second delay between
particular commands—for example, to permit a component to power up
completely—you can record “empty” steps into the macro by changing
Device Selector “pages” without entering actual command functions.
BUTTON ILLUMINATION TIMEOUT
ITALIANO
The HTR 7’s key-illumination can be set to remain lit for 0-9 seconds. The
default value is 2 seconds. To set the illumination timeout, simultaneously
press-and-hold for 3 seconds both the HTR 7’s [DISP] and the [0-9] key, with
the digit corresponding to the desired timeout duration; the Learn LED will
flash twice to confirm the new setting. When set to zero, the illumination
will not turn on at all.
Note
Key illumination is the biggest drain on the HTR 7’s batteries. A short
key-illumination timeout will extend battery life appreciably; turning it
off altogether (set it to 0 seconds) will lengthen it still further.
FACTORY RESET
DEUTSCH
The HTR 7 can be reset to its factory state, deleting all learned commands,
copied and punched-through keys, macros, and other setup information,
reverting all keys to their pre-programmed library commands.
To perform a factory reset simultaneously press-and-hold for 10 seconds
the HTR 7’s [ON] and [RTN] keys; the Learn LED will start to flash green.
Release [ON] and [RTN] before the second flash is complete; the Learn LED
will turn red, indicating the remote has been reset.
NEDERLANDS
Note
You must release [ON] and [RTN] before the second flash goes out, otherwise
the unit will not reset; should this occur, repeat the full procedure.
SVENSKA
РУССКИЙ
32
Downloaded From Disc-Player.com NAD Manuals
DELETE MODE
The HTR 7 can store learned, copied, and “default library” commands on any
single key (The default library commands are the pre-programmed NAD
codes, such as the native VISO FIVE commands on the [AMP] “page.”).
You can delete commands by layers back “down” to the default library
command on any key, removing learned commands, punched-through
functions, and copied keys.
Note
The default library commands cannot be deleted, so you need not worry
that using Delete Mode might cause irreparable changes.
To enter Delete Mode, simultaneously press-and-hold for 3 seconds both
the desired key’s Device Selector key and the [RTN] key, until the Learn LED
turns green. Press the function key whose command you wish to delete;
the Learn LED flashes; the number of times indicates which type of function
has become active - see the table below. Press the active Device Selector
key again to exit Delete Mode.
Note
You may delete multiple function-key commands on the same Device
Selector “page,” but to delete from more than one Device Selector page
you must exit Delete Mode and then re-enter it on the required page.
Flashes
Command Type
1
Default Library Command
2
Copied Library Command
3
Learned Command
Operation
When you enter the correct number the component will turn off; press
[ENTER] to accept that code library number and exit the Library Mode.
For example, to indicate code-library #501, the HTR 7 will flash [CUSTOM] 5
times, pause, and then flash [MACRO] once. You might wish to make a note
of your components’ code-library numbers.
LIBRARY CODE
NAD PRODUCT
DESCRIPTION
301
L75, L76 Tuner
302
L70 Tuner
Mode
Keys To Press (for 3 seconds)
S170
303
L53 Tuner
Learn/Copy/Punch Through
Device Key + [ ] Key
103
L75
304
L73 Tuner
Delete Mode
Device Key + RTN Key
104
Second Zone Commands
305
C425
Macro Record
Macro Key + Function Key
105
L70
306
C445
Library Mode
Device Key + Program Key
106
L76
307
Txx5 Series Tuner
Back Light Timeout
DISP Key + Digit Key
107
118
400
Tape Deck B
Factory Reset
See “Factory Reset” above
108
L53
401
TAPE Deck A
109
L73
500
TV 280
SLEEP MODE
110
Stereo Receiver/
Amplifier
501
MR13
111
Stereo Second Zone
502
MR20
112
Txx5 Series
503
PMR45
200
CD Player
600
T535, T562, T585, M55
201
CD Player (old)
601
T550, L55
The Sleep Mode timer will switch the VISO FIVE to Standby mode
automatically after a preset number of minutes. Pressing the HTR 7’s SLEEP
button once will display the setting of the sleep time increment. Pressing
the HTR 7’s SLEEP button a second time within a 3-second period will
change the sleep time increment in 30-minute intervals, after which time
the VISO FIVE will automatically switch into Standby mode.
102
202
5170, 5240, 5340
602
T512, T531, T532, T571,
T572
203
5325
603
L70, L73 DVD
204
5060
604
L56
205
M5
605
T513, T514, T515, T524,
T533, T534
300
Tuner
606
L53 DVD
SEARCH MODE
If none of the codes from the table, when entered, turns on the
component, and if you are quite sure you have followed the above
procedure completely and carefully, you may want to try the “search”
method as follows:
Summary of the HTR 7 Modes
To adjust the sleep delay, press the HTR 7’s SLEEP button twice; first to
display the sleep time increment, and a second time to change the
sleep time increment. The sleep time increment and a “SLEEP” icon will
continuously display on the VISO FIVE’s front panel Vacuum Fluorescent
Display (VFD). Each consecutive press increases the sleep time in 30-minute
increments from 30 to 90 minutes. To cancel the sleep mode, continue
pressing the HTR 7’s SLEEP button until “Sleep Off” displays on the VFD.
Switching the VISO FIVE to standby from either the HTR 7’s OFF or the
VISO FIVE’s POWER button will also cancel the sleep mode
NOTE
In order to use SLEEP button, make sure that HTR 7’s DEVICE SELECTOR
page is set to “AMP”.
Enter Library Mode by simultaneously pressing-and-holding for 3 seconds
both the desired Device Selector key and the [PROGRAM] button until the
Learn LED turns green. Now press-and-hold the HTR 7’s [
]) key; the
remote will step through all the available codes at a rate of approximately
1 per second.
Downloaded From Disc-Player.com NAD Manuals
FRANÇAIS
ITALIANO
101
DEUTSCH
100
РУССКИЙ
LIBRARY CODE
NAD PRODUCT
DESCRIPTION
Receiver/Processor
(Discrete ON/OFF)
Receiver/Processor
(Toggle ON/OFF)
CHECKING CODE-LIBRARY NUMBER
You can check the current code-library on any Device Selector key as
follows. Enter Library Mode by simultaneously pressing-and-holding for
3 seconds both the desired component’s Device Selector key and the
[PROGRAM] key until the Learn LED turns green. Press the [DISP] key; the
HTR 7 indicates the current code-library by flashing its [CUSTOM], [VCR],
and [MACRO] keys.
ESPAÑOL
While keeping the HTR 7 pointed toward the component, enter the first
appropriate three-digit code-library number from the table below. Press
[OFF]. If the component turns off, press [ENTER] to accept that code-library
number and exit the Library Mode. If the component does not turn off,
enter the next three-digit code-library number from the table.
Note
It is possible that search mode will find code-libraries that operate, at
least partially, some other brand (non-NAD) components. You may
certainly exploit such capabilities as you find them. However, since we
can only ensure the completeness or accuracy of NAD code-libraries, we
cannot support the HTR 7’s operation with other-brand components.
NEDERLANDS
Begin by ensuring that the component you wish the HTR 7 to control is
plugged in and powered-up (“on,” not merely in standby). To enter the
HTR 7’s Library Mode, simultaneously press-and-hold for 3 seconds both the
desired Device Selector key and the [PROGRAM] key, until the Learn LED
turns green.
When the component turns off, immediately release the cursor key; press
[ENTER] to accept that code-library and exit the Library Mode. Try a few
commands; should you prove to have stepped past the needed codelibrary, re-enter the Library Mode and use the cursor key to step back to it.
SVENSKA
LOADING CODE LIBRARIES
The HTR 7 can store a different library of default NAD codes for each of its
Device Selector “pages.” If the original default library does not control your
NAD CD player, DVD player, or other component, follow the procedure
below to change the code-library.
ENGLISH
USING THE HTR 7 REMOTE CONTROL
33
Reference
TROUBLESHOOTING
ENGLISH
CONDITION
No sound from all channels.
POSSIBLE CAUSES
• AC power unplugged.
POSSIBLE SOLUTIONS
• Check AC cable connection and outlet.
• Power not switched on.
• Outlet has no power.
No sound from some channels.
FRANÇAIS
• Faulty/missing cables.
• Check cables.
• Speaker connections faulty.
• Check speaker connections.
• “Speaker Settings” channel (s) set to “Off”.
• Check “Speaker Settings” menu.
• Subwoofer is off, not powered or improperly
connected.
• Power-up subwoofer, check Sub’s AC outlet
or check connections.
• Sub level set too low.
• Correct subwoofer level by adjusting “SUB”
button at HTR 7.
• Batteries are flat or incorrectly inserted.
• Check batteries.
• IR transmitter window on remote or IR receiver
window on VISO FIVE is obstructed.
• Check IR windows and ensure clear line-ofsight from remote to VISO FIVE.
• VISO FIVE front panel is in very bright sunlight
or ambient light.
• Reduce sunlight/room lighting.
• Microprocessor error.
• Power down the VISO FIVE via the front
panel Power switch and unplug it from the
AC outlet.
• VISO FIVE may have over heated.
• Wait five minutes, re-connect and power up.
The POWER is ON, but the internal DVD
player does not work.
• No disc is inserted.
• Insert a disc.
No picture.
• The TV is not set to receive video signal.
• Select the appropriate video input mode on
the TV so that the picture from the VISO FIVE
appears on the TV screen output.
• The video cable is not connected securely.
• Connect the video cable into the jacks
securely.
• The connected TV power is turned off.
• Power on the TV.
• HDMI connector is plugged-in and “HDMI Res.”
is set to 720P, 1080I or AUTO.
• Unplug HDMI cable connected to rear
panel’s HDMI OUT.
No sound from Subwoofer.
VISO FIVE does not respond to HTR 7
remote control.
ESPAÑOL
VISO FIVE does not respond to front panel
commands or remote control.
ITALIANO
DEUTSCH
• At DVD mode and with no disc loaded (“NO
DISC”)
1 Press and hold [DISPLAY] button. The lower
line of the VFD will show the current HDMI
resolution setting.
2 Use the remote’s [
] keys or toggle
[MEMORY] button to select through
480P/576P, 720P, 1080I, AUTO or OFF.
Select either “480P/576P” or “OFF” to enable
component video out, composite and S-Video
output. Stop at your desired resolution setting
and release [
] keys or [MEMORY] button.
NEDERLANDS
• The disc is dirty.
• Clean the disc.
The internal DVD player does not start
playback.
• No disc is inserted.
• Insert a disc
• An unplayable disc is inserted.
• Insert a playable disc (Check the disc type
colour system and Regional code).
• The disc is placed upside down.
• Place the disc with the playback side down.
• The disc is not placed within the guide.
• Place the disc correctly inside the guide on
the disc tray.
• A menu is on the TV screen.
• Press SETUP button of HTR 7 to turn off the
menu screen.
• The disc is dirty.
• Clean the disc.
• The password entered was wrong.
• Enter the correct password.
SVENSKA
The playback picture is poor.
Parental Control cannot be changed.
• Password was forgotten.
РУССКИЙ
• Set the VISO FIVE to factory default settings.
1 Place the VISO FIVE into AM mode.
2 Press quickly the three front panel buttons;
[PLAY/PAUSE] then [STOP] then [DISPLAY],
holding the [DISPLAY] button for more than
7 seconds. The VISO FIVE will switch itself off
then back on to DVD mode.
Note: Default password is 2580.
34
Downloaded From Disc-Player.com NAD Manuals
REFERENCE
ENGLISH
SPECIFICATIONS
AMPLIFIER SECTION
Power output Stereo Mode 2 x 60W
IHF dynamic power; 8 Ω
2 x 80W
IHF dynamic power; 4 Ω
2 x 120W
Power output Surround Mode
5 x 45W
Total harmonic distortion at rated power
0.08%
IM distortion at rated power
0.08%
Damping factor, 8 Ω >60
Input sensitivity and impedance 300 mV/47kΩ
Frequency response
± 0.5 dB (ref. 20Hz to 20kHz)
Signal/noise ratio
>100 dB (ref rated power/ 8Ω A-WTD)
Signal/noise ratio
>85 dB (ref 1W/ 8Ω A-WTD)
FRANÇAIS
FM SECTION
87.5MHz - 108MHz
10 dBu
70 dB
65 dB
0.3%
0.3%
50 dB
0.2%
Tuning range
Usable sensitivity, MONO
S/N Ratio MONO
S/N Ratio STEREO
Total Harmonic Distortion, MONO
Total Harmonic Distortion, STEREO
Channel Separation
RDS decode sensitivity
ITALIANO
522kHz -1620kHz (Europe version, 9kHz steps)
530kHz -1710kHz (North America version, 10kHz steps)
60 dBu
40 dB
1.5%
ESPAÑOL
TUNER SECTION
AM SECTION
Tuning range
Usable sensitivity
S/N ratio
Total Harmonic Distortion
DVD SECTION
SYSTEM
Signal system
Laser
CD
DVD
Frequency response
Signal-to-noise ratio (audio)
Dynamic range (audio)
Total Harmonic Distortion
OUTPUT
Video out
S-video (Y signal)
S-video (C signal)
Component (Y signal) Component (Cb/Cr signal) SCART (RGB signal)
HDMI Audio/Video Out
Digital out (coaxial)
Digital out (optical)
1Vp-p/ 75Ω
1Vp-p/ 75Ω
0.286 Vp-p/ 75Ω
1Vp-p/ 75Ω
0.7Vp-p/ 75Ω
0.7Vp-p/ 75Ω
Ver 1.0 x 1
0.5 Vp-p/ 75Ω
-15 dBm ~ -21 dBm
Dimensions (W x H x D) Net Weight
Shipping Weight 435 x 135 x 370 mm
12.6 kg
15.6 kg
NEDERLANDS
DEUTSCH
PAL/NTSC/Auto
Two wavelength laser diode
Wavelength 790nm
Wavelength 650nm
± 0.5 dB (ref. 20Hz to 20kHz)
100 dB (A-WTD)
95 dB (A-WTD)
0.02%
SVENSKA
PHYSICAL SPECIFICATIONS
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are registered
trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
The XM name, XM Ready and related logos are registered
trademarks of XM Satellite Radio Inc.
Downloaded From Disc-Player.com NAD Manuals
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535 & other
U.S. and worldwide patents issued & pending. DTS, DTS Digital
Surround, and ES are registered trademarks and the DTS logos,
Symbol and DTS 96/24 are trademarks of DTS, Inc. ©1996-2007
DTS, Inc. All Rights Reserved.
Official DivX® Certified product Plays all versions of DivX® video
(including DivX® 6) with standard playback of DivX® media files.
DivX DivX Certified, and associated logos are trademarks of DivX,
Inc. and are used under license.
This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
35
РУССКИЙ
Note: Dimensions include feet, volume knob and extended speaker terminals.
Specifications are subject to change without notice. For updated documentation and features, please log onto www.NADelectronics.com for the latest information about VISO FIVE.
www.NADelectronics.com
©2009 NAD ELECTRONICS INTERNATIONAL
A DIVISION OF LENBROOK INDUSTRIES LIMITED
All rights reserved. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International
VISO FIVE Owner’s Manual Issue 2.13-05/09
Downloaded From Disc-Player.com NAD Manuals