SoundLinQ3 SL3x Installation/Operation Manual

www.vaistech.com
Owner’s Manual
Audio Interface Controller
with built-in
XM Satellite Radio interface
(required XM Direct CNP2000UCA)
TOYOTA • LEXUS • SCION
Copyright (C) 2003-2012 VAIS Technology
Published August 7, 2012
Before You Start
2
WARNING
DO NOT DISASSEMBLE OR ALTER
Doing so may result in an accident, fire or electric shock
Do not block your view
Do not mount product or any added audio and/or video equipment where it can block your view through the windshield or
your view of dashboard indicators and displays.
Do not block the airbag
Do not mount product or any added audio and/or video equipment where it can obstruct the operation of any safety
devices such as the airbag.
Distraction warning
Do not let product or any added audio and/or video equipment distract you while you are driving.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL
Before starting any installation work , you must wait 90 seconds after turning the ignition switch to the LOCK position and disconnecting the negative (-) terminal
from the battery. The supplemental restraint system (airbag) is equipped with a backup power source. If installation work is started less 90 seconds after
disconnection of the negative (-)battery terminal, the SRS may deploy. When the negative (-) terminal cable is disconnected from the battery the clock and audio
systems memory will be erased. Before starting installation work make a record of the clock and audio systems memory settings. When installation is complete,
reset the clock and audio systems to their previous settings . Power tilt, power telescopic steering column, front power seats, power mirrors, and power shoulder
belt anchorage are equipped with a memory function .The rear power seat is not equipped with a memory function. e and they can make a record of the memory
contents, rear power seat is not equipped with the memory function. When installation is complete, it is necessary to readjust the features to their previous settings
Never use a backup power supply (such as another battery) during installation work to avoid losing these memory settings.
CAUTION
DO NOT SPLICE INTO ELECTRICAL CABLES
Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of
the wire and result in fire or electric shock .
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS
Cables or wiring that obstruct or get caught on places such as the steering wheel, shift lever, brake pedals, etc. can be
extremely hazardous.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST
Moisture or dust may result in product failure.
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS
The wiring and installation of this product requires special technical skills and experience.
USE ONLY SPECIFIED ACCESSORY PARTS
Use of other than specified parts may damage product internally.
FOLLOW THE OPERATIONAL AND INSTALLATION MANUALS.
YOU SHOULD READ AND FAMILIARIZE YOURSELF THOROUGHLY WITH THE FOLLOWING INFORMATION PRIOR
TO INSTALLING AND USING THIS UNIT. IN ADDITION, YOU MUST CAREFULLY READ AND FOLLOW THE
INSTALLATION SCHEMATICS/INSTRUCTIONS FOR THE PRODUCT AND THE VEHICLE IN WHICH IT IS BEING
INSTALLED. FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS MAY DAMAGE THE PRODUCT AND THE
VEHICLE, WILL VOID THE PRODUCT WARRANTY, AND MAY VOID THE VEHICLE WARRANTY
CHECK YOUR LOCAL LAWS
Some States/Provinces or other governmental jurisdictions (such as cities) may have laws that prohibit the operation of a
video screen within the sight of the Driver. If you have purchased such a product, you should use the product only in
locations where it is legal to do so, and if you do use the product, set up the screen so it is only visible to passengers.
TROUBLESHOOTING
Should this product fail to operate properly, please contact your Dealer or our Customer Service Department at
support@vaistech.com.
Before You Start
3
IMPORTANT
This unit is an interface adapter for Toyota/Lexus head unit to control the XM Direct Tuner (Model # CNP2000UCA)
(SOLD SEPARATELY) .
This unit is equipped with:
!
!
Built-in Electronic Ground Noise Isolator to eliminate unwanted car engine noise.
Resettable Fuses (provides protection for electronic circuits from over-current conditions)
About XM Radio Operation
!
!
!
The unit may refuse to change the channel if your reception is going ON and OFF.
Please wait until your reception stabilizes in order for the unit to allow you to change the channel
easily.
Due to bad reception in some areas, XM Radio may not work and/or not able to display text.
TEXT INFORMATION ONLY AVAILABLE FOR RADIOS WHICH SUPPORT SAT mode, CD or MD CHANGER
WITH A CD-TEXT or MD-TEXT CAPABILITY. Please see attached chart to determine emulation that is compatible
with your vehicle.
4
Connections
Connecting the units
SoundLinQ3
12-Pin Y-harness
SoundLinQ3
Interface Adapter
Model SL3x
SoundLinQ3
20-Pin Y-harness
SoundLinQ3
Audio Harness (36”)
XM Direct
CNP2000UCA
Vehicle Antenna
Vehicle Antenna
and XM Direct Tuner
CNP2000UCA
are included in
SL3x-TKIT only
RED LED
Service
Port
Power and Audio
wiring harness
Mode
Programming
switch
Interface connector
for CNP2000UCA Tuner
5
Connections
Connecting SoundLinQ3 to head unit using 20-pin Y-harness
Head Unit (Radio Receiver)
A
20-pin connector
Lexus GX 470 Radio Receiver shown as an example.
Locate connector “A” (20-pin connector) on your Radio.
Connector location on the Radio may be
different from shown above.
Plug into
Head Unit
(connector “A”)
To SoundLinQ3
Factory Audio
harness
SoundLinQ3
Audio Harness (36”)
SoundLinQ3
20-Pin Y-harness
Connection diagram used for all 2001-2009 Lexus vehicles
Connecting SoundLinQ3 to head unit using 12-pin Y-harness
Head Unit (Radio Receiver)
B
! CAUTION
Toyota head units
20-pin connector
IS NOT COMPATIBLE
with SoundLinQ3
Audio Harness
used for Lexus vehicles
12-pin connector
Factory Audio
harness
Lexus GX 470 Radio Receiver shown as an example.
Locate connector “B” (12-pin connector) on your Radio.
Connector location on the Radio may be
different from shown above.
(if present)
Plug into
Head Unit
(connector “B”)
To SoundLinQ3
SoundLinQ3
12 Pin Y-harness
SoundLinQ3
Audio Harness (36”)
Connection diagram used for most 2004-2012 Toyota vehicles and
for most 2004-2009 Lexus vehicles (excluding Lexus SC430)
! WARNING
To Un-plug any connector do NOT pull it by the wires.
6
Installation
IMPORTANT
We strongly recommend that you install the unit in an easily accessible location, so you can later upgrade
the unit or re-program it in case of incorrect programming.
Installation
@
@
@
@
@
@
@
@
@
Gain access to the back of your vehicle’s Head Unit.
Find the same port as our Y-Harness (see “Connecting SoundLinQ3 to head unit”)
Disconnect the existing connector and plug in our Y-Harness connector into this port, then plug female end of Audio
Harness to plug into your factory connector . Audio harness female connector is not used in some vehicles, in
this case isolate unused plug to prevent accidental shortage to vehicle body.
Plug the other end of Audio cable into designated port on this unit.
Connect XM Radio Receiver interface cable as shown in the picture. (see “Connecting the units”)
Setup proper Emulation Mode for the unit (see “Emulation Mode Selection”)
Turn the car on and check SoundLinQ3 functionality (especially Text capability) before the final assembly.
Please mount this unit in an easily accessible location for upgrading and re-programming purposes.
Secure the Head Unit in its original position.
Emulation Mode Selection (CD and MD changer emulation)
MD Changer Emulation Mode programming steps:
@
@
@
@
@
@
@
@
Properly install the unit.
Put both programming switches in the “DOWN” position.
Put ignition switch into the “ACC” position.
Wait for a long beep followed by a few short beeps. This may take up to one minute.
Return programming switches into their default position (both switches “UP”). Wait up to 30 seconds until
confirmation beep.
Put ignition switch into the “OFF” position. Wait at least 10 seconds.
Put ignition switch into the “ACC” or “ON” position.
Check SoundLinQ3 for functionality, especially TEXT capabilities.
1 2
ON
Both switches
“DOWN”
1 2
ON
Ignition into
“ACC” or “ON”
position
Ignition into
“OFF” position
Confirmation beep
(Red LED blinks)
Both switches
“UP”
up to 30 sec
up to 10 sec
Confirmation beep
(Red LED blinks)
CD Changer Emulation Mode programming steps:
@
@
@
@
@
@
@
@
Properly install the unit.
Put “Right” programming switch in the “DOWN” position.
Put ignition switch into the “ACC” position.
Wait for a long beep followed by a few short beeps. This may take up to one minute.
Return programming switches into their default position (both switches “UP”). Wait up to 30 seconds until
confirmation beep.
Put ignition switch into the “OFF” position. Wait at least 10 seconds.
Put ignition switch into the “ACC” or “ON” position.
Check SoundLinQ3 for functionality, especially TEXT capabilities.
1 2
ON
1 2
ON
Right switch
“DOWN”
Ignition into
“ACC” or “ON”
position
Confirmation beep
(Red LED blinks)
Both switches
“UP”
up to 30 sec
Ignition into
“OFF” position
Confirmation beep
(Red LED blinks)
IMPORTANT
!
!
Improper Emulation Mode setting may cause unit to be unrecognized by head unit.
By activating “CD or MD Changer Emulation Mode” you force the unit to find proper location in the vehicle
Audio/Video network.
up to 10 sec
7
Installation
Emulation Mode Selection (SAT emulation)
SAT Emulation Mode programming steps:
@
@
@
@
@
@
@
@
Properly install this unit.
Put “Left” programming switch in “DOWN” position.
Put ignition switch into the “ACC” position.
Wait for long beep followed by a few short beeps. This may take up to one minute.
Return programming switches into their default position (both switches “UP”). Wait up to 30 seconds until
confirmation beep.
Put ignition switch into the “OFF” position. Wait at least 10 seconds.
Put ignition switch into “ACC” or “ON” position.
Check SoundLinQ3 for functionality, especially TEXT capabilities.
1 2
ON
Left switch
“DOWN”
1 2
ON
Ignition into
“ACC” or “ON”
position
Confirmation beep
(Red LED blinks)
Both switches
“UP”
up to 30 sec
Confirmation beep
(Red LED blinks)
Mounting unit using Velcro fasteners
SoundLinQ3
“Hard” Velcro Fastener
“Soft” Velcro Fastener
Carpet or car chassis
!
!
NOTE
Velcro Fasteners are not included
VAIS Technology strongly recomand to ground unit to the car chassis for best results
Ignition into
“OFF” position
up to 10 sec
8
Emulation
CD CHANGER OR
MD CHANGER
EMULATION
SAT EMULATION
CD/MD Changer Emulation
Functionality Description
9
Audio input dedicated for XM radio receiver can only be used for XM Radio integration. Control of XM Radio
Receiver is done through your head unit or the steering wheel controls (explained below). This unit supports the XM
Direct Tuner . (Model # CNP2000UCA)
This unit can be programmed in CD changer emulation mode , MD changer emulation mode or SAT Emulation.
Please see attached chart to determine which emulation mode is compatible with your vehicle.
By connecting this unit to the factory system you add a logical device ( XM Radio interface).
The Radio display will show device as a “CD/CD1/CD2” or “MD1”.
CD changer emulation
MD changer emulation
For Radio Receiver with LCD
For Radio Receiver with LCD
XM Radio CH027 (MD changer emulation)
XM Radio CH019 (CD changer emulation)
For Radio Integrated into Navigation System
XM Radio CH001 (MD changer with a MD-TEXT)
XM Radio CH023 (CD changer emulation with CD-Text)
For Radio Integrated into Navigation System
XM Radio CH081 (MD changer emulation)
XM Radio CH023 (MD changer emulation)
Head Unit Controls
Source Selection (CD/MD Emulation)
Select desired source by pressing DISC button on the head unit or MODE on the steering wheel control.
(See diagram below)
Head Unit:
To switch between the unit sources you need to use the “DISC” or “CD” button on the radio
(Diagram below assumes factory CD changer is present).
CD
CD1
CD
XM Radio
CD
OR
MD1
CD
XM Radio
Steering Wheel control:
To switch between the unit sources you need to use the “MODE” button on the steering wheel control.
(Diagram below assumes following sources are present).
AM
FM1
FM2
TAPE
CD
CD1
XM Radio
10
XM Radio controls
You must set the correct Display Mode, in order to display channel number and TEXT information correctly.
( See “XM Radio Input Settings” for details).
TRACK+ and TRACK-
Select Next/Previous channel (if the selected channel is not available, the unit will jump to the next available channel).
(SCROLL)
and
Speed channel selection +10, -10 (if the selected channel is not available, the unit will jump to the next available channel).
If “DISC SCAN” mode is activated [SCROLL] buttons work as [DISC+] and [DISC-]*.
NOTE: Available only if PRESET CHANNELS are setup. This feature was created for vehicles which do not have
[DISC+], [DISC-] buttons.
DISC+
and
DISC-
Used for PRESET CHANNEL selection.
NOTE: Assumed at least one PRESET CHANNEL exists (see “Presets”).
NOTE: If PRESET CHANNEL list has not been previously set [DISC+] and [DISC-] work as [SCROLL] buttons.
SCAN
Used for setup purposes. (Please refer to “Display settings and Special Features”).
DISC SCAN
Please see SCROLL buttons functionality.
NOTE: Buttons [DISC RPT], [RANDOM], [DISC RANDOM] are not supported.
DISC RAND
Enables/Disables “Disc information” popup window. (Popup window comes up when song title and artist name change).
NOTE: Popup window functionality vary on the Lexus model and Audio System configuration.
IMPORTANT
For vehicles where information is displayed on the Radio LCD please activate [DISC RANDOM] in order to have
information correctly updated.
DISC RPT
To select whether Song Name or Artist Name displays first. We recommend using this feature especially for cars where
Radio is not integrated into Navigation Screen.
Displayed Errors (available only with CD-Text or MD-Text capability)
-NO SIGNAL-TUNER ERR-
No signal or antenna disconnected
Satellite receiver is not connected or does not respond
Direct Entry Mode
SoundLinQ3 supports “Direct Entry Mode” only for vehicles with Radio integrated into Navigation System.
Simply touch numeric
buttons to enter channel
number in “Direct entry mode”
NOTE: Direct input isn't available for Radio with its own LCD Display
If you select a channel higher than 299 this unit will direct you to the channel according to the following example.
Example: If you select channel 567, the system will select channel 67. If channel 67 is not available the unit will stay on
current channel.
11
XM Radio controls
Presets
Adding a new PRESET
@
@
@
Select the desired channel
Press the [RPT] or [REPEAT] button 4 times (MUST BE DONE within 1-2 seconds). You will hear a beep.
SoundLinQ3 will store the current channel in the preset list. You can store up to 10 preset channels, and channels get
recorded in sequential order.
NOTE: Beep indicates successfully accomplished operation. If you do not hear a beep, please repeat the above steps.
Changing an existing PRESET
@
@
@
@
Select the preset you would like to change (using the [DISC+], [DISC-] buttons)
Select new desired channel (using the [TRACK+], [TRACK-] buttons, or use “Direct entry” on the Navigation screen
(if supported). Make sure you do not select channels which already exist in “Presets list”, because unit will move to
another preset.
Press the [RPT] or [REPEAT] button 4 times (MUST BE DONE within 1-2 seconds). You will hear a beep.
SoundLinQ3 will update the preset list.
NOTE: Beep indicates successfully accomplished operation. If you do not hear a beep, please repeat the above steps.
Erasing PRESETS
@
@
@
@
@
Enter into “XM Radio Input Settings” Mode ( See “XM Radio Input Settings” for details)
Press the [DISC RPT] or [DISC REPEAT] button one time to activate the “DISC REPEAT” function.
Press the [DISC RPT] or [DISC REPEAT] button again to deactivate it.
SoundLinQ3 will produce a long beep as an confirmation of successful erasure.
Exit “XM Radio Input Settings” Mode ( See “XM Radio Input Settings” for details)
Satellite Signal Strength
@
@
@
Press the [SCAN] button 4 times (MUST BE DONE within 1-2 seconds). You will hear a short beep.
SoundLinQ3 will display the signal strength in position where channel number is normally displayed
To cancel this mode simply press [TRACK+], [TRACK-].
NOTE: Use this mode to find the proper antenna location for best reception.
Used to display “Signal Strength”
Note: Will range from 0-99
XM Radio Input Settings
Enter/Exit “XM Radio Input Settings” Mode
@
@
@
Press the [SCAN] button 8 times (MUST BE DONE within 1-2 seconds) to enter “XM Radio Input Settings” Mode. You
will hear a short beep as a confirmation.
SoundLinQ3 will use the “REPEAT” indicator (continuous blinks 2 times per second) on your head unit to confirm “XM
Radio Input Settings” Mode is active.
Press the [SCAN] button 8 times (MUST BE DONE within 1-2 seconds) to exit “XM Radio Input Settings” Mode.
You will hear a short beep as a confirmation.
NOTE: In this mode you can setup Display Settings, Erase PRESETS list, and Adjust Sound Level for XM Radio Input
XM Radio controls
12
Display Settings
About Display Settings
SoundLinQ3 supports 8 types of Display Modes. Display Mode can ONLY be set up for the XM Radio source.
It is critical to setup, the correct Display Mode for the following reasons:
! For Channel information to be displayed correctly.
! For Text information to be displayed.
Display mode 1 - Minutes and Seconds used to display the selected channel number.
Minutes display hundreds, seconds display 00-99. DISC number and TRACK number are ”invisible”
NOTE: This mode is preferred with CD changer emulation for Radio receivers with their own LCD.
Display mode 2 - Same as Display mode 1, except that DISC and TRACK number always display “1”.
NOTE: Some Radio receivers refuse to display minutes and seconds if DISC or TRACK number are “invisible”. Please use this
mode if your Radio receiver displays only “CD1” on the LCD.
Display mode 3 - In this mode TRACK number is used to display hundreds, Minutes are used to display tens, Seconds are
used to display single digits. DISC number is “invisible”.
NOTE: This mode is most common for the radio integrated into the Navigation System.
Display mode 4 - In this mode TRACK number used to display hundreds, Minutes are used to display tens, Seconds are
used to display single digits. DISC number is always “1”.
Display mode 5 - Alternate variation of Display mode 1.
Display mode 6 - In this mode TRACK number is either 10, 11 or 12 where “0” from 10, “1” from 11 and “2” from 12 are used
to display hundreds, Minutes are used to display tens, Seconds are used to display single digits. DISC number is always “12”.
NOTE: This mode is most common for the radio integrated into the Navigation System which does not display Song Tilte in MD
changer emulation mode (Alternative for Display Mode 3, allows Song Title to be displayed for channels less than 100) .
Display mode 7 - In this mode TRACK number is either 10, 1 or 2 where “0” from 10, “1” and “2” are used to display
hundreds, Minutes are used to display tens and single digits. DISC number is always “12”.
Display mode 8 - In this mode TRACK number is either 10,11 or 12 where “0” from 10, “1” from 11 and “2” from 12 are used
to display hundreds, Minutes are used to display tens, Seconds are used to display single digits. DISC number is always “12”.
NOTE: Alternative to Display Mode 7.
NOTE: Use Display mode 8 in MD changer emulation mode. In this mode TRACK number is used to display the channel
number.
Changing Display Mode
@
@
@
@
@
Enter into “XM Radio Input Settings” Mode ( See “XM Radio Input Settings” for details).
Press [SCROLL UP] to switch between Display Modes.
Check channel 23, 81, 92, and 123, to confirm correct Display Mode selection.
Make sure both Disc Title and Track Title information is displayed correctly.
Exit “XM Radio Input Settings” Mode ( See “XM Radio Input Settings” for details).
13
XM Radio controls
Display Settings
Displaying Channel Information
Track number, Minutes, and Seconds are
used to display the selected satellite
channel number.
NOTE: For cars with the Radio integrated
into the Navigation System, “DISC” number
MUST BE “invisible” or “12” in order to
have all ten numbers available for “Direct entry”.
Artist Name
Song Title
Channel Name
NOTE: On some Radios both DISC number and TRACK number
must be different from “0” or “invisible in order for TEXT to be displayed properly.
Minutes and Seconds are
used to display selected satellite
channel number.
NOTE: Present if MD-TEXT is supported by the Radio
Receiver (may differ on Head units model and year)
NOTE: Please check channel 081, 092
and 123 to make sure those channel
numbers are displayed properly.
XM Sound Level Adjustment
@
@
@
@
@
@
@
@
Enter into “XM Radio Input Settings” Mode ( See “XM Radio Input Settings” for details).
Select the desired satellite channel.
Activate the “SCAN” function on your head unit.
Set the desired volume at your head unit.
While “SCAN” is active use [SCROLL UP] to increase volume and [SCROLL DOWN] to decrease volume.
Sound level [01..31] will be displayed as Seconds on you head unit.
Deactivate “SCAN” function.
Exit “XM Radio Input Settings” Mode ( See “XM Radio Input Settings” for details).
NOTE: Remember, a high sound level may result in noticeable sound distortion.
SAT Radio Emulation
Functionality Description
14
SAT Emulation
Audio input dedicated for XM radio receiver can only be used for XM Radio integration. Control of XM Radio
Receiver is done through your head unit or the steering wheel controls (explained below). This unit supports the XM
Direct Tuner (Model # CNP2000UCA)
Please see attached chart to determine which emulation mode is compatible with your vehicle.
By connecting this unit to the factory system you add a logical devices ( XM Radio interface).
SAT1, SAT2, and SAT3 can be used for 6 presets each.
SAT Emulation
For Radio Integrated into Navigation System
XM Radio CH023 (SAT emulation)
XM Radio SAT2 CH070 (SAT emulation )
XM Radio CH001 (SAT emulation Text display)
XM Radio SAT3 CH004 (SAT emulation )
15
Head Unit Controls
Source Selection (SAT Emulation)
Select desired source by pressing the AM button on the head unit or MODE on the steering wheel control.
(See diagram below)
Head Unit:
To switch between unit sources, press the AM button on the head unit. The AM button will cycle through the following
modes: AM radio, SAT1, SAT2, and SAT3. SAT1, SAT2 and SAT3 are presets for the satellite receiver.
AM
SAT1
SAT2
SAT3
XM Radio
Steering Wheel control:
To switch between unit sources, press the MODE button on the steering wheel control. The diagram below shows the
order in which sources are selected.
(Diagram below assumes following sources are present).
AM
SAT1
SAT2
XM Radio
SAT3
FM1
FM2
TAPE
CD
XM Radio controls
16
MANUAL TUNING
Use the TUNE knob on the head unit to select channels. You can rapidly scan channels by turning the knob faster in the
direction you wish to scan.
CHANNEL SEEK
TRACK+ and TRACK-
Use the SEEK-TRACK button on the stereo head unit to select the next available channel. The unit will automatically
skip channels that are not available.
CHANGING CATEGORIES
TYPE and
TYPE
To change the category of channels you would like to listen to, press either the TYPE < or TYPE > button.
DISPLAYING SONG TITLE AND ARTIST NAME
To display the song title and artist name that is currently playing, press the TEXT button. If the information is available
from the current satellite channel, it will be displayed. Song title and artist name can display a maximum of 16
alphanumeric characters each.
SELECTING PRESETS
To select a preset, press the desired preset button.
TYPE SCAN
Scan channels throughout the selected category.
Displayed Errors (available only with CD-Text or MD-Text capability)
-NO SIGNAL-TUNER ERR-
No signal or antenna disconnected
Satellite receiver is not connected or does not respond
Presets
Adding a new PRESET
@
@
@
Select the desired channel
Press and hold the preset button where you would like to store the current channel.
You will hear a beep when the channel has been stored in the preset location.
NOTE: Beep indicates successfully accomplished operation. If you do not hear a beep, please repeat the above steps.
Changing an existing PRESET
@
Presets can be overwritten at any time using the same procedure as adding a new Preset.
Erasing PRESETS
@
Presets can not be erased, but they can be overwritten at any time by following the procedure for Adding a new
Preset.
XM Radio controls
17
XM Radio Input Settings
You can adjust the input sound level of your satellite receiver. The sound level adjustment allows you to balance the
volume control with other sources connected to your head unit (such as CD player, FM radio, etc), and eliminate possible
distortions caused by high input levels.
Activate / Deactivate SETTINGS MODE
@
@
@
@
Go to SAT 3
Tune to channel 255
Press [Type Scan] 8 times to hear long beep (MUST be done within 1-2 seconds).
Using AM or AM/SAT button reselect sources to cycles to SAT 3
Satellite Sound Level Adjustment
@
@
@
@
@
@
@
@
Activate SETTINGS MODE
To adjust the sound level, first you must select a source that is not connected to the SoundLinQ3 unit, such as CD
player or FM radio. Set the volume to a comfortable level while listening to this source.
Change the source to SAT1 or SAT2 and select a satellite channel to listen to.
Change the source to SAT3.
Press and hold the button labeled SAT Lev Adj or number 5 on the Radio with its own LCD. You will hear a short
beep, and should then hear sound coming from the satellite receiver source.
Now you will adjust the sound level to match the volume of the source you selected in step 1. To adjust the sound
level, press either the TYPE < or TYPE > button.
Once the sound level matches the volume of your source from step 1, press the SAT Lev Adj (or number 5 on the
Radio with its own LCD) again to store the desired sound level in memory.
Deactivate SETTINGS MODE
Channel Tuning Options
17
IMPORTANT
SoundLinQ3 can operate in two modes. Applicable for software starting Ver 4.51 (released Nov 15, 2012).
OPTION 1 is when unit displays all available and unavailable channels. Programmed by default.
No channel list update is required at any time.
OPTION 2 is when unit displays available channels only.
Keep in mind every time XM changes channel list, you have to do channel list update in order for new channels
to be available for selection.
To go from OPTION 1 to OPTION 2 you need to perform the “Channel List Update”.
To go from OPTION 2 to OPTION 1 you need to push and hold “EnblAllCH” in “Settings Mode”.
Activate / Deactivate SETTINGS MODE
@
@
@
Go to SAT 3
Tune to channel 255
Press [Type Scan] or [SCAN] ( Depending on your radio model) 8 times to hear long beep (MUST be done within 1-2
seconds).
SAT3 - SETTINGS MODE
Channel List Update
If XM Radio adds/removes a channel, you need to use [RESCAN] feature to update “Channel List”.
1. Activate “Settings Mode” steps are above.
4. Push and hold "RESCAN" or "Preset #4" on your radio to hear a short beep.
5. Unit will automatically switch to SAT 1.
6. "Updating" will start blinking, indicating that the update is in progress.
7. Make sure to let the "Channel List" fully update before you use your Radio again. This will take 2-3 minutes.
8. Once the update is complete, another short beep will sound, and “Updating” will disappear.
LICENSING AGREEMENT, DISCLAIMERS AND LIMITED
WARRANTY
18
VAIS TECHNOLOGY, LLC
LICENSE AGREEMENT
VAIS TECHNOLOGY- SoundLinQ3 (SL3i),(SL3x), (SL3s)
for U.S.A. (hereinafter referred to as ‘PRODUCT’) and its related software
For Most Toyota/Lexus Vehicles 2001-2009; (hereinafter collectiv ely referred to as ‘PRODUCTS’). THIS IS A LEGAL AGREEMENT
BETWEEN YOU, AS THE END USER, AND VAIS TECHNOLOGY, LLC (“VAIS”). PLEASE CAREFULLY READ THE TERMS AND
CONDITIONS OF THIS AGREEMENT BEFORE USING THE VAIS PRODUCTS. BY USING THE VAIS PRODUCTS AND SOFTWARE
INSTALLED ON THE VAIS PRODUCTS, YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS AGREEMENT. THE AUDIO
INTERFACE CONTROLLER AND THE AUDIO VIDEO INTERFACE CONTROLLER ARE ESSENTIALLY THE BRIDGE BETWEEN A
VEHICLE, ITS EQUIPMENT, AND ANY ‘AFTER-MARKET’ EQUI PMENT SUBSEQUENTLY ADDED TO THE VEHICLE BY THE ENDUSER. THE EQUIPMENT SOLD TO YOU, THE END USER, IF PROPERLY INSTALLE D. IS A RESETTABLE TECHNOLOGY, WHICH
WILL, UNDER NORMAL CIRCUMSTANCES, AU TOMATICALLY DISCONNECT IN THE EVENT OF ANY MALFUNCTION. SINCE VAIS
DOES NOT INSTALL THIS EQUIPMENT, VAIS DISCLAIMS AN Y LIABILITY FOR IMPROPER INSTALLATION OF THE VAIS
TECHNOLOGY OR THE ‘AFTER-MARKET’ EQUIPMENT (INPUTS). FURTHER, THE ‘END USER’ ACKNOWLEDGES THAT THE
PRODUCT AND ITS SOFTWARE ARE NOT INHERENTLY DANGEROUS AND DO NO T PROVIDE ANY INHERENT RISKS AND
THEREFORE POTENTIAL DAMAGES TO THE END-USER, OTHER THAN ‘Fitness for its Purpose’. Some radio receiver models may
cause you to experience some technical difficulties, if the product does not operate properly please contact technical department promptly at
support@vaistech.com.
1. GRANT OF LICENSE
VAIS grants to you a non-transferable, non-exclusive license to use the PRODUCT and its software installed on the VAIS product (the
“PRODUCTS”) and the related documentation solely for your own personal use or for internal use by your business, only on such VAIS
PRODUCTS. You shall not copy, reverse engineer, translate, port, modify or make derivative works of the Software contained in t he
PRODUCT. You shall not loan, rent , disclose, publish, sell, assign, lease, sublicense, market or otherwise transfer the Software in the
PRODUCT or use it in any manner not expressly authorized by this agreement. You shall not derive or attempt to derive the source code or
structure of all or any portion of the Software in the PRODUCT by reverse engineering, disassembly, recompilation, or any other means. You
shall not use the Software in the PRODUCT to operate a service bureau or for any other use involving the processing of data for other
persons or entities. VAIS and its licensor(s) shall retain all copyright, trade secret, patent and other proprietary ownership rights to the
Software in the PRODUCT. The PRODUCT S are Copyrighted/ Patented and/or at various stages of Pending and may not be copied, even
if modified or merged with other products. You shall not alter or remove any copyright notice or proprietary legend contained in or on the
PRODUCTS. You may transfer all of your license rights in the Software or the PRODUCT, the related documentation and a copy of this
License Agreement And Warranty to another party, provided that the party reads and agrees to accept the terms and conditions of this
License Agreement And Warranty.
2. OPERATIONAL WARNING AND SAFETY INSTRUCTIONS.
IMPORTANT NOTICE: YOU SHOULD READ AND FAMI LIARIZE YOURSELF THOROUGHLY
WITH THE FOLLOWING INFORMATION PRIOR TO INSTALLING AND USING THE –
SoundLinQ3 (SL3i), (SL3x), (SL3s) and its related software (THE “PRODUCTS”).
IN ADDITION, YOU MUST CAREFULLY READ AND FOLLOW THE INSTALLATION
SCHEMATICS/INSTRUCTIONS FOR THE PRODUCT AND THE VEHICLE IN WHICH IT IS
BEING INSTALLED. FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS MAY DAMAGE
THE PRODUCT AND THE VEHICLE AND WILL VOID THE PRODUCT WARRANTY AND MAY
VOID THE VEHICLE WARRANTY. (A copy of the installation schematics is included with
the Product and can also be found on the VAIS TECHNOLOGY website at
www.vaistech.com.)
FAILURE TO ABIDE BY THESE OPERATIONAL WARNINGS AND SAFETY INSTRUCTIONS
COULD RESULT IN SERIOUS BODILY INJURY OR DEATH. IN ADDITION, FAILURE TO
FOLLOW THESE INSTRUCTIONS MAY VOID THE PRODUCT WARRANTY AND COULD
BECOME A BASIS FOR LIABILITY ON THE PA RT OF THE VEHICLE OPERATOR IN THE
EVENT OF AN ACCIDENT WHICH RESULTS IN INJURY TO PERSONS OR PROPERTY.
UNDER NO CIRCUMSTANCES WILL VAIS OR ITS IMMEDIATE AGENTS OR PRINCIPALS,
BE LIABLE, FOR DAMAGES INCURRED TO THE PRODUCTS, THE VEHICLE OR ITS
PASSENGERS, OR OTHER THIRD-PARTIES AS A RESULT OF FAILURE TO FOLLOW
VAIS’S INSTALLATION INSTRUCTIONS.
19
A COPY OF THE ‘OPERATIONAL WARNINGS AND SAFETY INSTRUCTIONS’ IS TO BE KEPT
WITH THE VEHICLE AT ALL TIMES.
3.DISCLAIMER AND LIMITATION OF WARRANTIES .
(A) EXCEPT AS OTHERWISE CONTAINED HEREIN , the PRODUCTS and related documentation are provided to you, “AS IS”. IN NO
EVENT SHALL VAIS BE LIABLE FOR ANY DAMAGES, CLAIM OR LOSS INCURRED BY YOU (INCLUDING WITHOUT LIMITATION,
COMPENSATORY, INCIDENTAL, INDIRECT , SPECIAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES, LOST PROFITS, LOST
SALES OR BUSINESS, EXPENDITURES, INVESTMENTS, OR COMMITMENTS IN CONNECTION WITH ANY BUSINESS, LOSS OF
ANY GOODWILL, OR DAMAGES. THE TERM ‘INCIDENTAL DAMAGES’ REFERS TO THE EXPENSES OF TRANSPORTING THE
PRODUCTS TO THE VAIS SERVICE CENTER, LOSS OF THE END-USERS [ORIGINAL PURCHASER’S] TIME, LOSS OF THE USE OF
THE PRODUCT, BUS FARES, CAR RENTALS OR OTHER COSTS RELATED TO THE CARE AND CUSTO DY OF THE PRODUCT. THE
TERM ‘CONSEQUENTIAL DAMAGES’ REFERS TO THE COST OF REPAIRING OR REPLACING OTHER PROPERTY, WHICH IS
DAMAGED WHEN THIS PRODUCT DOES NOT WORK PROPERLY.) RESULTING FROM THE USE OR INABILITY TO USE THE
PRODUCTS, INCLUDING ANY DAMAGES INCURRED DUE TO THE NEGLIGENT OPERATION OF A MOTOR VEHICLE, IN
CONJUNCTION WITH THE USE OF SAID PRODUCTS. THE END-USER ACKNOWLEDGES ITS RESPONSIBILITY FOR THE USE OF
THE PRODUCT. THE ADDITION OF VAIS PRODUCTS AND ANY AFTER-MARKET EQUIPMENT MAY ENHANCE THE VALUE OF A
VEHICLE OR CAUSE A THIRD-PARTY TO ILLEGALLY ATTEMPT TO REMOVE THE PRODUCTS AND AFTER-MARKET EQUIPMENT.
VAIS DISCLAIMS ANY LIABILITY RELATE D TO SUCH THEFT AND POTENTIAL DAMAGE TO PROPERTY.IT IS THE END-USERS
RESPONSIBILITY TO PROTECT ITS OWN PROPERTY.
THE END-USER FURTHER ACKNOWLEDGES THAT THE OPERATIO N OF A MOTOR VEHICLE IS AN INHERENTLY DANGEROUS
ACTIVITY, AND BY ITS USE OF VAIS’S PRODUCTS, ACKNOWLEDG ES THAT THE PRODUCTS ARE REMOTELY RELATED TO SAID
MOTOR VEHICLE OPERATION, AND THUS ANY DAMAGES CAUSED TO THE DRIVER OF THE VEHICLE, THE VEHICLE ITSELF OR
ANY THIRD-PARTY AND ITS PROPERTY IS NO T THE RESPONSIBILITY OF VAIS, ITS AG ENTS OR ITS PRINCIPALS AND IS THE
SOLE RESPONSIBILITY OF THE DRIVER OF SAID VEHICLE.
YOU, THE END-USER, OR ANY OTHER DRIVER OF THE VEHICLE, IS SOLELY RESPONS IBLE FOR THE SAFE OPERATION OF THE
VEHICLE AND THE SAFETY OF BOTH YOU AND THE PASSENGERS . FOR SAFETY PURPOSES, THE PRODUCT SHOULD NOT BE
USED FOR THE DRIVER’S ENTERTAINMENT, WHILE THE VEHICLE IS BEING DRIVEN. SUCH USE COULD BE A DISTRACTION TO
THE DRIVER, WHICH COULD CAUSE AN ACCIDENT LEADING TO SER IOUS INJURY OR DEATH. IF YOU, THE END-USER ALLOW
ANOTHER PERSON TO USE THE VEHICLE, IT IS YOUR RESPONSIBILITY TO THOROUGHLY BRIEF THAT OTHER USER, ON THE
SAFETY REQUIREMENTS FOR OPERATING THE VEHICLE AND THE PR ODUCTS INSTALLED THEREIN.
(B) SAID DISCLAIMERS SHALL APPLY TO THE USE OF SAID PR ODUCTS, EVEN IF VAIS HAS BEEN INFORMED OF, KNEW OF, OR
SHOULD HAVE KNOWN OF THE LIKELIHOOD OF SUCH DAMAGES. THIS LIMITATION APPLIES TO ALL CAUSES OF ACTION IN THE
AGGREGATE, INCLUDING WITHOUT LIMITATION: BREACH OF CONTRACT, BREACH OF WARRANT Y, NEGLIGENCE, STRICT
LIABILITY, MISREPRESENTATION AND OTHER TORTS. IF VAIS’S WARRANTY DISCLAIMER OR LIMITATION OF LIABILITY SET
FORTH IN THIS AGREEMENT SHALL, OR FOR ANY REASON WHATSOEVER, BE HELD UNENFORCEABLE OR INAPPLICABLE, YOU
AND ANY OTHER END USER AGREE THAT VAI S’S LIABILITY SHALL NOT EXCEED (50%) OF THE PRICE PAID FOR THE ENCLOSED
VAIS PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not
apply to you. This Warranty Disclaimer and Limitation of Liability shall not be applicable to the extent that any federal, state or local law,
which cannot be preempted, prohibits any provision of this Warranty.
(C) Some States/Provinces or other governmental jurisdictions (such as cities) may have laws that prohibit the operation of a video screen
within the sight of the Driver. If you have purchased such a product, you should use the product only in locations where it is legal to do so,
and if you do use the product, set up the screen only where it may be visible to passengers only. Although VAIS strongly recomm ends that
Products not be used while the vehicle is in motion, it is your responsibility to determine whether the product can be used in any given
location. Any use of the PRODUCTS where it is illegal to do so, may be used against you as evidence of negligence in the event of an auto
accident or other traffic infraction.
4. THIRTY (30)- DAY MONEY BACK WARRANTY ONLY IF PURCHASED DIRECT FROM
VAIS.
Any Product purchased directly from VAIS, referencing a Return Authorization Number (RAN) during the Thirty-(30) day period following
shipment by VAIS, may be returned for a full refund of the purchase price actually paid, only if you have received damaged, def ective or
incorrectly shipped merchandise. The RAN number may be obtained from VAIS’s Customer Support at (720) 733-2348, and is valid for
only thirty- (30) days from its issuance. Said RAN must be noted on the outside of the returned PRODUCTS’ packaging. The PRODUCTS
must be returned in its original packaging, intact, without any evidence of tampering with the PRODUCTS or physical damage caused by the
Customer (End-User).
WE WOULD STRONGLY RECOMMEND THAT THE ITEM BE SHIPPED INSURED, SINCE THE RISK OF LOSS DURING SHIPPING IS
WITH THE END-USER. Re-stocking Fees may apply. Damage Fees if deemed caused by the End-User may apply. SHIPPING AND
HANDLING OF THE END-USER IS NOT REFUNDABLE AND MUST BE PREPAID, FOR THIS WARRANTY TO BE APPLICABLE. ENDUSER SHALL ASSUME ALL RISK OF LOSS FOR THE SHIPPING OF THE PRODUCTS TO VAIS. PLEASE ALLOW UP TO EIGHT (8)
WEEKS FOR VAIS TO CREDIT YOUR ACCOUNT .
20
5. LIMITED WARRANTY.
VAIS warrants that the PRODUCTS will be free from defects in materials and workmanship for a period of ONE (1) YEAR from the
date of purchase. VAIS’S sole obligation under this warranty is to repair or replace at VAIS'S option, any PRODUCTS that VAIS
shall have determined to be defective. Any replacement of parts, shall at the option of VAIS and at no additional charge to the enduser, be new or rebuilt/re-engineered replacement parts. Any replacement of PRODUCTS shall be with new or remanufactured
equivalent PRODUCTS. The End-User is responsible for all shipping costs to VAIS, in connection with warranty service. VAIS will
not be liable for any defects arising out of any modification of the PRODUCTS, or misuse, neglect, improper installation not in
accordance with the specifications provided byVAIS, or if the product is used in violation of any applicable local, state or federal laws. It is
the End Users responsibility to ascertain the existence and applicability of any local laws to the operation of the PRODUCTS, in any location
where the PRODUCTS are being used. other causes beyond Seller's reasonable control.
A. WHO PERFORMS VAIS TECHNOLOGY'S WARRANTY COMPLIANCE.
VAIS Technology’s professional technical depar tment will perform VAIS warranty obligations.
B. WHAT YOU MUST DO.
To obtain warranty performance, you must take the PRODUCTS, or deliver the PRODUCTS freight prepaid, to a VAIS Technology
Authorized Service Center. If shipped, the PRODUCTS must be packaged so that it is protected from possible shipping damage. VAIS
Technology will ship the PRODUCTS to you when warranty performance is completed. VAIS Technology will pay for shipping the
PRODUCTS to you, if the product was repaired under the warranty and the Product was received by the Service Center during the warranty
period, in which case the Product will be returned to you freight prepaid by VAIS. You must present to the Service Center, or include with
your shipment, a dealer's bill of sale, or other original evidence, showing the date and place of purchase and describing the Product
purchased to establish warranty eligibility. Be sure to include your return address and a written description of the problem and a daytime
telephone number where you can be reached should the need arise.
SHIP TO:
ATTENTION:
VAIS Technology
13792 Compark Blvd, Suite 125
Englewood, CO
80112
SERVICE DEPARTMENT
For your own protection, you should obtain a proof of delivery receipt. Return shipping (that is, shipping back to the customer following repair
or replacement), will be paid by the Seller unless repair or replacement is determined not to be covered by the warranty.
C. WHAT THE WARRANTY DOES NOT COVER . VAIS shall have no liability or obligation to Purchaser with respect to any
PRODUCTS requiring service during the warranty period which is subjected to any of the following: abuse, improper operation, negligence,
accident, modification, improper connections, failure of the end-user to follow the operating procedures outlined both herein, and in any
user's manual, attempted repair by non-qualified personnel, Company or Association; operation of the Product outside of the pub lished
environmental and electrical parameters, or if such Product's original identification (trademark, serial number) markings have been defaced,
altered, or removed. VAIS excludes from warranty coverage Products which have not been sold by VAIS or an Authorized VAIS Deale r to
the Purchaser. VAIS also excludes from warranty coverage Products sold outside of the United States. All wires and connectors
furnished with, or as part of the PRODUCTS is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly
provided otherwise in any documentation or license agreement furnished with the PRODUCTS.
Other Items Not covered Pursuant to this Warranty:
1.
2.
3.
4.
Damage occurring during shipment of the product to VAIS for repair (claims must be presented to the carrier);
Any cost or expense related to the removal or reinstallation of the product;
Any Products which have been adjusted, altered or modified without VAIS’s consent;
Any Products that has been determined to contain an excessive amount of dust or dirt and any product that contains any
other contaminants including liquid or foreign objects.
REPAIR OR REPLACEMENT AS PROVIDED IN THIS WARRANTY IS THE PURCHASER'S EXCLUSIVE WARRANTY REMEDY.
IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR
PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THE APPLICABLE PARTS WARRANTY PERIOD AND NO PERSON,
COMPANY OR ASSOCIATION (INCLUDING AUTHORI ZED DEALERS) IS AUTHORIZED TO ASSUME FOR VAIS ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE OF THE PRODUCT.
D. ALL WARRANTIES EXPRESS OR IMPLIED, ARE HEREBY DISCLAIMED BY VAIS, AND ANY SUCH WARRANTY IS DEEMED
VOID, IN THE EVENT THE END-USER ATTEMPTS TO MODIFY THE PRODUCT OR PRODUCTS IN ANY WAY.
In addition, some states, do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights and you
may have other rights, which may vary, from state to state. THE ABOVE WARRANTY TERMS AND CONDITIONS ARE VALID ONLY IN
THE U.S.A.
IMPORTANT STEPS TO SAFEGUARD YOUR DATA AND PROPERTY :
Be sure to remove all third-party after market equipment, options, alterations, and attachments not warranted by VAIS Technolog y before
sending the Product to VAIS for warranty service. VAIS IS NOT LIABLE FOR ANY LOSS OR DAMAGE TO THESE ITEMS.
6. OTHER PROVISIONS:
21
A. INDEMNIFICATION OF VAIS, ITS AGENTS AND EMPLOYEES . By Purchasing, Installing and Using the Products, You, the EndUser, agree to indemnify, defend and hold harmless, VAIS, and it s Affiliates, Directors, Officers, Agents and Employees from an y Liabilities,
Damage, Loss, Claim and Expense (including reasonable Attorney’s Fees) arising out of the installation and use of the Products.
B. GOVERNING LAW. THIS AGREEMENT, and all Purchases hereunder shall be governed by, and construed under the laws of the
State of Colorado, without regard to conflicts of law rules. You agree that the Courts of Colorado shall have exclusive jurisdi ction over the
Parties, for all disputes. Venue shall lie exclusively in either: (i) Arapahoe County District Court; or the U.S. District Cour t, District of
Colorado.
C. NOT FOR RESALE NOR EXPORT ASSURANCES . You, the End-User certifies and agrees that the Products are being
Purchased for the End-Users own use, and not for resale. The End-User further agrees that he/she/it will not remove components from
Product for resale, unless he/ she/ it becomes certified as an official dealer of VAIS and enters into the appropriate ‘Distrib ution Agreements’
required by VAIS technology. The End-User further agrees that neither the software, nor any other technical date received from VAIS, nor
the direct Product thereof, will be exported outside the United States, except as authorized and as permitted by VAIS and in accordance with
the laws and regulations of the United States. If the software or Products rightfully obtained by you outside of the United States, you agree
that you will not export the Software, Products, nor other technical data, received from VAIS; except as authorized and as permitted by
VAIS, and in accordance with the laws and regulations of the United States. VAIS and the End-User recognize that violation of t hese
provisions will result in damages to VAIS, in a substantial amount, which is not easily determined. If these provision are violated, the EndUser shall be liable to VAIS in the amount of $100/day, as liquidated damages and not as a penalty, commencing with the first d ay in which
the end-user violates this provision and ending on the day in which such Products or its parts are recovered by VAIS.
D. FORCE MAJEURE. VAIS Technology shall not be liable for any delay or failure in performance caused by or resulting from acts of
God, fire, flood, storms, earthquakes, tornados, other acts of nature, any accidents, riots, wars, government intervention, embargoes, strikes,
labor difficulties, equipment failures, or any other causes beyond the control of VAIS Technology. Quantities are subject to av ailability. In the
event of shortage, VAIS Technology may allocate sales and deliveries in its sole discretion.
E. WAIVER. Failure of VAIS Technology to insist upon strict performance of any provisions hereof shall not be deemed a waiver of its right
and remedies.
F. SEVERABILITY: In the event that any of the provisions, or portions thereof, of this Agreement are held to be unenforceable or
invalid by any court or tribunal of competent jurisdiction, the validity and enforceability of the remaining provisions, or portions thereof, shall
not be affected thereby, and effect shall be given to the intent manifested by the provisions, or portions thereof, held to be enforceable and
valid.
G. CONSTRUCTION: Throughout this Agreement the singular shall include the plural, and the plural shall include the singular, and
masculine shall include the feminine wherever the context so requires.
H. COMPETENCY OF THE PARTIES . Each party is legally competent and fully authorized to execute this Agreement.
I. OPPORTUNITY TO REVIEW AGREEMENT WI TH COUNSEL OF PARTIES OWN CHOOSING . You, the End-User acknowledge
that YOU have had every right to consult a licensed attorney, and have done so to the extent of your desires, prior to entering into this
Agreement, and: (a) has fully and carefully read and considered this Agreement prior to its execution; (b) has been sent to, or has had the
opportunity to be fully apprised by his or her attorney of the legal effect and meaning of this document and all of its terms a nd conditions; (c)
has had the opportunity to make whatever investigation or inquiry he/she deems necessary or appropriate in connection with the subject
matter of this Agreement; (d) has been afforded the opportunity to negotiate as to any and all terms of this Agreement; and (e) is executing
this Agreement voluntarily, free from any undue influence, coercion, duress or fraud of any kind.
J. BINDING EFFECT: Upon execution, this Agreement shall be binding and fully enforceable, and shall inure to the benefit of the
parties hereto, their successors, personal representatives and heirs.
K. NOTICES: All notices, as may be required by this Agreement, shall be sent to the respective parties at the addresses set forth
below. Appropriate registered or certified mailing to the parties may modify the place of notice.
L. ENTIRE AGREEMENT. These terms and conditions constitute the entire and exclusive agreement between you, the End-User and
VAIS Technology, concerning the Products, and your purchase hereund er, and supercede all statements or other agreements, whether oral
or written, between you and VAIS Technology. No change in this Agreement shall be effective, unless agreed to in writing by bot h, you, the
end-user and VAIS.
IF YOU DO NOT AGREE WITH THESE TERMS, PLEASE RETURN
THE VAIS PRODUCTS (INCLUDING THE SOFTWARE* AND ANY
WRITTEN MATERIALS) IN ORIGINAL CONDITION, AND IN
ORIGINAL PACKAGE (INCLUDING SHIPPING BOX, AND ALL
PACKAGING BELONGINGS USED FOR SECURE SHIPPING)
WITHIN FIVE (5) BUSINESS DAYS OF RECEIPT OF THE
PRODUCTS, TO THE PLACE FROM WHICH YOU PURCHASED
THEM, FOR A FULL REFUND OF THE PURCHASE PRICE OF
THE VAIS PRODUCTS.
* VALID FOR SPECIFIC VAIS PRODUCTS ONLY