Hi-drive
2A, 5A, 8A, 10A, 16A
25A, 35A, 45A, 75A
100A, 130A, 155A, 250A
user’s manual
rev.0.6
April 2010
Parker Hannifin S.p.A Divisione S.B.C
Parker
Hi-drive User Manual
Parker Hannifin S.p.A.
SSDSBC
Via Gounod. 1
20092 Cinisello Balsamo [MI]
T: +39 02 361081
F: +39 02 36108400
http://www.ssddrives. it
http://www.sbcelettronica .com
DICHIARAZIONE DI CONFORMITA CE
CE DECLARATION OF CONFORMITY
Dichiarazione N.
Declaration N.
DC016-R0.2
Costruttore
Manufacturer
PARKER HANNIFIN S.p.A. SSD SBC
Indirizzo
Address
Via Gounod, 1
20092 Cinisello Balsamo (MI)
ITALIA
Prod otto
Product
Azionamento
Drive
Nome del Prodotto
Product name
Serie HIDRIVE
HIDRIVE Series
e
II prodotto sopra descritto conforme a:
The above product is conform to:
Doc. N.
I
Doc. Nr.
EN 61800-5-1
EN 61800-3
EN 60204-1
Titolo I Title
Azionamenti elettrici a velocita variabile
Parte 5-1: Prescrizioni di sicurezza - Sicurezza elettrica, termica
ed energetica
Adjustable speed electrical power drive systems Part 5-l:
Safety Requirements- Electrical. thermal and enerqy
Azionamenti elettrici a velocita variabile. Parte 3:Norma di
prodotto relativa alia compatibilita elettromagnetica ed ai
metodi di prova specifici.
Adjustable speed electrical power drive systems Part 3: EMC
product standard including specific test methods.
Sicurezza del macchinario Equipaggiamento elettrico delle
macchine, Parte 1: Regale Generali
Safety of machinery- Electrical equipment of machines, Partl:
General requirements
Edizione
I
Edition
2003-04
2004-12
2006-06
Note/ notes:
I prodotti devono essere installati seguendo scrupolosamente le indicazioni riportate nel manuale d'uso e manutenzione.
These products must be installed scrupulously following the instructions written on the handbook.
I prodotti inclusi sono conformi ai requisiti della Direttiva 2006/95/CEE e della Direttiva 2004/108/EC.
These products are corresponding to the 2006/95/CEE requirements guideline and 2004/1 08/EC requirements guidelines.
Cinisello Balsamo, 0910712009
Giorgio COLNAGHI, Location Manager _ _ _ _ _ _ _ _ _ _ _ _ _ __
20092 Cinisello Balsamo (MI) -Italy- Via Gounod. 1- Tel. 02 66012459- Fax 02 66012808
SEDE LEGALE: 20094 Corsica (MI) -Italy- Via Privata Archimede, 1 - Tel. 02 45192.1 -Fax 02 4479340- internet: www.parker.comlit- E-mail: italy_parker@parker.com
lscr.. R. I. Mi N. 125728, REA MiN. 682188- Cap. Soc. Euro 1.230.000- P.l. I C.F. I VAT (IT) 00817430150- Banca Regionale Europea S.p.A. Ag.14
Page 2 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
This user manual is for the standard version of the converter.
All information in this user manual, including methods, techniques and concepts described
herein, are proprietary information of Parker Hannifin Divisione S.B.C. – EME Division and of
its licensees, and they shall non be copied or used without express authorization.
Parker Hannifin S.p.A. Divisione S.B.C. is committed to a continuous product upgrade and
reserves the right to modify products and user manuals at any time without prior notice. No part
of this user manual may be howsoever reproduced without previous consent by Parker Hannifin
S.p.A. Divisione S.B.C..
Abbreviations
FBK
Pr…
b…
FFW
R
W
Keypad-display
Drive
Feedback.
Decimal parameter.
Binary parameter (bit).
Feedforward, control advance function.
Read parameter.
Write parameter.
Keypad
Converter
Cod 1004261430
Page 3 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
INDEX
1 SAFETY INSTRUCTIONS........................................................................................9
1.1
Symbols and signals .................................................................................................. 9
1.2
General information..................................................................................................9
1.3
Safety instructions for transportation and storage ..............................................10
1.4
Safety instructions for commissioning...................................................................10
1.5
Safety instructions for operation ........................................................................... 11
1.6
Safety instructions for maintenance ......................................................................12
1.7
Compatibility with RCD devices............................................................................ 12
1.8
Applicable standards............................................................................................... 13
1.9
Materials and disposal ............................................................................................13
1.10
Warranty.................................................................................................................. 14
2 PRODUCT INTRODUCTION..................................................................................14
2.1
Product description .................................................................................................14
2.2
Identification............................................................................................................16
3 TECHNICAL DATA ................................................................................................18
3.1
Ambient conditions ................................................................................................. 18
3.2
Vibrations and shocks............................................................................................. 18
3.3
Available models......................................................................................................18
3.4
Power supply............................................................................................................19
3.5
Technical characteristics ........................................................................................20
3.6
Other characteristics...............................................................................................23
4 MOUNTING ............................................................................................................24
4.1
Dimensions and weights.......................................................................................... 24
4.2
Fastening .................................................................................................................. 27
4.3
Mounting instructions............................................................................................. 30
5 ELECTRICAL CONNECTIONS..............................................................................31
5.1
Connector pin-out ................................................................................................... 31
5.2
Cable lengths and cross sections ............................................................................ 40
5.3
Protections................................................................................................................ 42
5.4
Protective Earth connections..................................................................................43
5.5
Power stage supply connection...............................................................................44
5.5.1
Connection to AC 3-phase network ..........................................................................44
5.5.2
Connection to AC 1-phase network ..........................................................................46
5.5.3
Continuous supply connection .................................................................................. 47
5.6
External Power supply (fans) ................................................................................. 49
5.7
Motor connection (MIL connector) ....................................................................... 50
5.7.1
Motor without stationary brake .................................................................................50
5.7.2
Motor with stationary brake ...................................................................................... 51
Page 4 of 233
Parker Hannifin S.p.A Divisione S.B.C
5.8
5.9
5.10
5.11
5.11.1
5.11.2
5.11.3
5.11.4
5.11.5
5.11.6
5.11.7
5.12
5.13
5.14
5.15
5.15.1
5.15.2
5.16
5.17
5.17.1
5.17.2
5.17.3
5.18
6
Hi-drive User Manual
External braking resistor connection ....................................................................52
Control stage supply connection ............................................................................55
Analogue and digital I/Os connection....................................................................56
Feedback connection ............................................................................................... 58
Resolver..................................................................................................................... 58
Incremental encoder ..................................................................................................59
Sinusoidal encoder .................................................................................................... 60
Sinusoidal encoder + EnDat......................................................................................61
Sinusoidal encoder + Hiperface ................................................................................62
Incremental encoder + hall sensor.............................................................................63
SinCos (one sinwave per pole pitch)......................................................................... 64
Auxiliary encoder input connection.......................................................................65
Connecting converters to the electrical shaft........................................................66
Serial connection RS422/RS485 ............................................................................. 67
Serial connection RS232 ......................................................................................... 68
Without converter RS232/RS422..............................................................................68
With converter RS232/RS422................................................................................... 68
CAN Bus connection ...............................................................................................69
Electro-magnetic compliance .................................................................................70
Grounding.................................................................................................................. 70
Connection cables and shielding ...............................................................................71
Filters......................................................................................................................... 72
Cabling general layout ............................................................................................73
STATUS LEDS.......................................................................................................74
7 SUPPLY MODE......................................................................................................74
7.1
“Low voltage” supply.............................................................................................. 74
7.2
“High voltage” supply.............................................................................................75
8 START-UP..............................................................................................................76
8.1
Setting the default parameters ...............................................................................76
8.2
Selection of motor type ........................................................................................... 76
8.3
Changing motor data ..............................................................................................77
8.4
Setting feedback.......................................................................................................77
8.4.1
A feedback, input X6. ............................................................................................... 77
8.4.2
B feedback, input X7................................................................................................. 77
8.4.3
C Feedback , input X9............................................................................................... 78
8.4.4
Speed feedback configuration ...................................................................................78
8.4.5
Position feedback configuration................................................................................79
8.4.6
Digital filter per encoder ...........................................................................................80
8.5
Phasing procedure................................................................................................... 80
8.5.1
Type 1 phasing .......................................................................................................... 81
8.5.2
Type 2 phasing .......................................................................................................... 82
8.5.3
Pico-PLC phasing program .......................................................................................83
8.5.4
Fine phasing .............................................................................................................. 83
8.5.5
Phasing procedure for encoder with EnDat o Hiperface interface............................84
8.5.6
Motor phases .............................................................................................................84
8.6
Speed control ........................................................................................................... 85
Page 5 of 233
Parker Hannifin S.p.A Divisione S.B.C
8.7
Hi-drive User Manual
Speed control adjustment .......................................................................................85
9 ANALOG AND DIGITAL I/OS ................................................................................91
9.1
Digital I/Os ............................................................................................................... 91
9.2
Relay outputs ........................................................................................................... 91
9.3
Analog outputs......................................................................................................... 91
10
DYNAMIC BRAKING ..................................................................................92
11
11.1
KEY PARAMETERS ...................................................................................93
Key parameters .......................................................................................................97
12
12.1
12.2
12.3
12.3.1
12.3.2
12.3.3
12.3.4
12.4
12.4.1
12.4.2
12.4.3
12.5
12.6
12.7
12.7.1
12.7.2
12.7.3
12.7.4
12.7.5
12.7.6
12.7.7
OPERATING MODES ...............................................................................107
Position control...................................................................................................... 107
Torque control (operating mode 110)..................................................................110
Electrical shaft and positioned (op. mod. 120).................................................... 111
Speed mode: ............................................................................................................ 111
Electrical axis: ......................................................................................................... 111
Positioner................................................................................................................. 113
TAB0: profiles in memory ......................................................................................113
Electronic came (OPM121) ..................................................................................118
Posizionator............................................................................................................. 119
Speed mode ............................................................................................................. 119
CAM1 and CAM2...................................................................................................119
Electrical shaft and positioned (oper. mode 122) ...............................................128
Position control via CanBus (operating mode 140)............................................ 129
Additional useful functions................................................................................... 131
Capturing values......................................................................................................131
Programmable outputs.............................................................................................134
Encoder simulation..................................................................................................135
Motor cogging compensation..................................................................................136
Multiturn absolute encoder phasing on “zero” machine .........................................136
Encoder CAN ..........................................................................................................137
Ramp with “S” profile.............................................................................................139
13
13.1
13.1.1
13.2
13.3
PROGRAMMING DIGITAL INPUTS AND OUTPUTS ..............................140
The Pico-PLC.........................................................................................................140
Pico-PLC default program ......................................................................................146
Serial interface....................................................................................................... 147
Communication protocol ......................................................................................148
14
14.1
14.1.1
14.1.2
14.1.3
14.2
14.2.1
14.2.2
14.2.2.1
14.2.2.2
CANBUS INTERFACE..............................................................................153
SBC Can .................................................................................................................153
Description of fields in real time mode...................................................................154
Description of fields in communication mode ........................................................ 161
Description of extended message set #2 .................................................................163
CANopen DSP402 (D version) ............................................................................. 165
Dictionary object summary of ds301 ...................................................................... 168
Dictionary object summary of dsp402 .................................................................... 170
Object 6040h: Controlword.................................................................................173
Object 6041h: Statusword ................................................................................... 175
Page 6 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
14.2.2.3 Object 605Bh: Shutdown option code ................................................................177
14.2.2.4 Object 605Ch: Disable operation option code ....................................................178
14.2.2.5 Object 605Ah: Quick stop option code ...............................................................179
14.2.2.6 Object 605Eh: Fault reaction option code..........................................................179
14.2.2.7 Object 6060h: Modes of operation......................................................................180
14.2.2.8 Object 6061h: Modes of operation display .........................................................180
14.2.3
Functional description .............................................................................................181
14.2.3.1 Modes of operation function ............................................................................... 181
14.2.4
Homing mode.......................................................................................................... 182
14.2.4.1 General information ............................................................................................182
14.2.4.2 Input data description .......................................................................................... 182
14.2.4.3 Output data description ....................................................................................... 183
14.2.4.4 Internal states....................................................................................................... 183
14.2.4.4.1 Controlword of homing mode.........................................................................183
14.2.4.4.2 Statusword of homing mode ........................................................................... 183
14.2.4.5 Object dictionary entries ..................................................................................... 184
14.2.4.5.1 Objects defined in this chapter ........................................................................184
14.2.4.5.2 Objects defined in other chapters ....................................................................184
14.2.4.6 Object description ...............................................................................................184
14.2.4.6.1 Object 607Ch: Home offset ............................................................................. 184
14.2.4.6.2 Object 6098h: Homing method ....................................................................... 185
14.2.4.6.3 Object 6099h: Homing speeds......................................................................... 185
14.2.4.6.4 Object 609Ah: Homing acceleration...............................................................186
14.2.4.7 Functional description .........................................................................................187
14.2.4.8 Homing methods ................................................................................................. 187
14.2.4.8.1 Method 1: Homing on the negative limit switch and index pulse...................187
14.2.4.8.2 Method 2: Homing on the positive limit switch and index pulse....................188
14.2.4.8.3 Methods 3 and 4: Homing on the positive home switch and index pul. ......... 188
14.2.4.8.4 Methods 5 and 6: Homing on the negative home switch and index pul. ........189
14.2.4.8.5 Methods 7 to 14: Homing on the home switch and index pulse .....................189
14.2.4.8.6 Methods 15 and 16: Reserved .........................................................................190
14.2.4.8.7 Methods 17 to 30: Homing without an index pulse ........................................191
14.2.4.8.8 Methods 31 and 32: Reserved .........................................................................191
14.2.4.8.9 Methods 33 to 34: Homing on the index pulse ............................................... 191
14.2.4.8.10
Method 35: Homing on the current position ...............................................191
14.2.5
Profile position mode .............................................................................................. 192
14.2.5.1 Internal states....................................................................................................... 192
14.2.5.1.1 Controlword of profile position mode ............................................................ 192
14.2.5.1.2 Statusword of profile position mode ............................................................... 192
14.2.5.2 Object dictionary entries ..................................................................................... 193
14.2.5.2.1 Objects defined in this chapter ........................................................................193
14.2.5.2.2 Object 607Ah: Target position........................................................................193
14.2.5.2.3 Object 6081h: Profile velocity ........................................................................194
14.2.5.2.4 Object 6083h: Profile acceleration..................................................................194
14.2.5.2.5 Object 6084h: Profile deceleration.................................................................. 195
14.2.5.2.6 Object 6085h: Quick stop deceleration ...........................................................195
14.2.5.2.7 Object 6086h: Motion profile type.................................................................. 196
14.2.5.3 Functional description .........................................................................................196
14.2.5.4 Functional description .........................................................................................198
14.2.6
Interpolated Position Mode ..................................................................................... 200
14.2.6.1 Object 60C0h: Interpolation sub mode select .....................................................201
Page 7 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
14.2.6.2 Object 60C1h: Interpolation data record............................................................. 201
14.2.7
Drive parameters .....................................................................................................204
14.2.8
CANopen monitor by ASCII commands ................................................................ 205
15
15.1
15.2
15.2.1
15.2.2
PROGRAMMING THE CONVERTER THROUGH A PC ..........................207
MotionWiz..............................................................................................................208
Hyperterminal connection....................................................................................209
Creating and setting a connection ...........................................................................209
ASCII protocol port RS-232 ...................................................................................211
16
USE OF (OPTIONAL) KEYPAD................................................................214
17
APPENDIX A : CONVENTIONS ...............................................................217
18
APPENDIX B : FLASH INFORMATION ...................................................217
19
APPENDIX C : SOFTWARE TIMING........................................................218
20
APPENDIX D : ALARMS ..........................................................................219
21
APPENDIX E : CONTINUOUS WORKING ...............................................221
22
APPENDIX F : EXTERNAL CAPACITOR ................................................224
23
23.1
23.2
23.3
23.4
23.5
23.6
23.7
APPENDIX G : OPTION “R” FOR SAFE DISABLE FUNCTION .............225
Introduction ........................................................................................................... 225
Signals description.................................................................................................226
Drive function blocks ............................................................................................ 227
Connections............................................................................................................ 228
Operation, sequence and timing ..........................................................................228
Example.................................................................................................................. 230
Test and maintenance ........................................................................................... 230
24
APPENDIX H : RETENTIVE VARIABLE ..................................................231
25
HISTORY OF MANUAL REVISIONS........................................................232
Page 8 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
1 Safety instructions
1.1 Symbols and signals
Several symbols and signals are used in this safety instruction.
Pay attention to the following meanings :
Extremely severe risk. Disregarding the following advise may involve danger
of life.
Severe risk. Disregarding the following advise may involve serious personal
injury.
Medium risk. Disregarding the following advise may involve personal injury
1.2 General information
•
Only persons who are qualified and trained for the use and operation of the equipment
may work on this equipment or within its proximity. The persons are qualified if they
have sufficient knowledge of the assembly, transportation, installation and operation of
the equipment as well as an understanding of all warnings and precautionary measures
noted in these instructions. The user must also observe local safety regulations.
•
Before installing and commissioning the drive, read carefully this documentation and
strictly observe all technical, safety and wiring information, including identifying labels
placed on the drive (ratings). In case of doubt contact the Parker Hannifin service centre.
•
Drives are to be intended as components for use in machine or systems. Therefore they
can be used only in machine or systems that are in compliance with the low voltage
directive 73/23/CEE (modified by 93/68/CEE) and with the electro-magnetic
compatibility directive 89/336/CEE.
•
Electronic equipments are generally not “fail-safe” components. Therefore the machine
manufacturers should carry out a risk analysis for the whole machine in order to ensure
that moving parts (motors) cannot bring personal injury in case of failures of electronic
devices.
Page 9 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
1.3 Safety instructions for transportation and storage
•
•
•
The ambient conditions given in the product documentation must be observed for
transportation and storage (temperature, humidity, mechanical stress and aggressive
atmosphere).
Drives contain components sensitive to electrostatic charges which can be damaged by
inappropriate handling. Therefore during installation / removal of drives, provide the
necessary safety precautions against electrostatic discharges (discharge electrostatic
charges of the human body before touching the drive, always place the drive above
conductive plates and avoid touching it with insulating material like synthetic fibres,
polymeric materials etc…)
Risk of injury by incorrect handling !
Incorrect handing of the equipment may cause severe personal injury. Use appropriate
tools for transportation, lifting, handling and mounting. Wear appropriate clothing for
accident-prevention (safety shoes, safety glasses, safety gloves, etc...).
1.4 Safety instructions for commissioning
•
•
•
•
•
• The high voltages inside the drive imply risk of electric shock. Make sure that drive and
motor are properly grounded accordingly to national regulations. Furthermore the drive,
before switching it on, must be closed in a protective cabinet in order to avoid direct
contact with accessible live parts.
Only qualified and trained personnel is allowed to perform installation and commissioning,
using appropriate tools and following the safety precautions given in this instruction. Make
sure that supply voltage has been switched off before installing and wiring.
Drives are only allowed to be operated on TT, TN grounded industrial mains having
maximum 480V+10% line to line rms voltage, as specified in the user manual. Do not directly
install the drive on ungrounded (IT) or asymmetrically grounded mains. In case of
ungrounded mains, coupling with Dyn transformer with grounded secondary circuit is
necessary. Refer to drive technical data and wiring instruction.
All the components used in the cabinet in which the drive is installed, (cables, contactors,
inductors and transformers, fuses, etc...), and the connected motor, must be in compliance
with the specification given in the product documentation, in addition to national regulations.
Make sure that the maximum temperature inside the cabinet does not exceed 45°C (113°F). If
necessary, use an appropriate air conditioning.
The size and temperature rating of wires and cables used for connecting the drive must be in
compliance with the specification given in the instruction manual (see NEC 310-16 for USA).
Use also the specified tightening torque.
Make sure about the correct drive-motor matching: voltage and current ratings must be
compatible.
• The user is responsible for over-current and short circuit protection of the drive. Read
carefully the specification given in the user manual.
Page 10 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
1.5 Safety instructions for operation
•
•
•
•
•
•
•
•
•
High voltage ! Risk of electric shock ! Danger of life !
All live parts must be protected against direct contact. The drive must be closed inside a
cabinet before switching it on.
Working on power live parts (terminals) must be conducted with the drive switched-off.
Dangerous voltages may be present at power terminals even after the supply has been
switched off and the motor stopped. Make sure the equipment cannot switched on
unintentionally. Wait at least 6 minutes before working on live parts after the unit has
been switched-off.
The drive and the motor must be permanently connected to earth accordingly to the
connection diagram, even for brief measurements or tests.
High leakage current ! Risk of electric shock ! Danger of life !
Earth leakage current during operation may exceed 3,5 mA AC or 10mA DC.
Earth connection must be permanent : use copper wire having a minimum size of 10mm2
throughout all the length.
Before switching the equipment on, make sure that all devices, including the motor, are
permanently connected to earth, even for brief test or measurements, as shown in the
wiring diagrams. Otherwise high voltages may appear on equipment conductive surfaces
with danger of electrical shock.
Always refer to current local regulations for grounding. For installation within European
Community refer to EN61800-5-1 product standard, section 4.2.5.4.2. For installation in
the USA refer to NEC (National Electric Code) and NEMA (National Electric
Manufacturers Association). The product installation should always comply with the
above said standards.
Hot surfaces ! Danger of injury ! Danger of burns !
Some external surfaces of the equipment and same internal part may reach very high
temperatures. Danger of burn and injury if touching these parts.
After switching the equipment , wait at least 15 minutes to allow it to cool before
touching it.
Page 11 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
Dangerous movements ! Danger of life !
• Dangerous movements can be caused by faulty control of the connected motor.
Same common example are :
€
€
€
€
Improper or wrong installation and wiring
Wrong input parameters before or during operation (programming)
Defective components (drive, motor, wires, sensors, etc...)
Incorrect control (software or firmware errors)
• In order to prevent personal injury due to unintended dangerous motor movements, pay the
maximum attention and work on the machine with a qualified and tested safety system :
€ Isolate the drive power connection.
€ Mount the emergency stop switch in the immediate reach of the operator. Verify that the
emergency stop works before start-up. Don’t operate the machine if the emergency stop
is not working.
€ Install properly fences, guards, coverings and light barriers in order to prevent people
from accidentally entering the machine’s range of motion.
€ Secure vertical axes against falling or dropping after switching off the motor power
€ Make sure that the drives are brought to a safe standstill before accessing or entering the
danger zone.
1.6 Safety instructions for maintenance
•
•
It is extremely dangerous to remove covers or part of the external enclosure from the
equipment. Risk of personal injury. The warranty immediately decay.
In case of malfunction consult the alarm list described in the user manual or address
Parker Hannifin. The drives are not field repairable.
1.7 Compatibility with RCD devices
The use of RCD (Residual Current Devices) is strongly not recommended.
If the use of RCD is mandatory, use type B only (for DC and AC prospective earth current). Set
the trip level at 300mA (fire protection level) or more.
Setting the trip level at 30mA (protection level against direct contact) is possible only using
time-delayed RCD and low leakage current EMC filters, but in any case the drives are not
guaranteed to operate with 30mA trip level.
Page 12 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
1.8 Applicable standards
Safety
73/23/CEE
directive Low voltage directive
modified by 93/68/CEE
EN 50178
Electronic equipment for use in power installations
EN 60204-1
Safety of machinery – Electrical equipment of machines – Part 1:
General requirements
EN 61800-2
Adjustable speed electrical power drive systems – Part 2: General
requirements – Rating specifications for low voltage adjustable
frequency a.c. power drive systems
EN 61800-5-1
Adjustable speed electrical power drive systems – safety
requirements, thermal and energy
EN 954-1 / ISO 13849-1 Safety of Machinery - Safety-related Parts of Control Systems Part 1: General Principles for Design provides such a set of
categories
UL508C
(USA) Power Conversion Equipment
CSA22.2 Nr. 14-05
(Canada) Power Conversion Equipment
Electromagnetic Compatibility (Immunity/Emission)
89/336/CEE directive
EMC directive
EN 61800-3
Adjustable speed electrical power drive systems. Part 3 : EMC
product standard including specific test method
The drives are to be intended as components to be used in a second environment (industrial
environment) and category C3, together with specific EMC filters and installed accordingly to
the recommendation given in the user manual. When used in the first environment (residential /
commercial environment), drives may produce radio-frequency interference dangerous for other
equipments : additional filtering measures must be implemented by the user.
1.9 Materials and disposal
- zinc coated steel sheet, thickness 1mm and 2mm
- extruded aluminium AlSi
- ABS “Novodur” thickness 2mm minimum
- adhesive polycarbonate (label)
Electrolytic capacitor contain electrolyte and printed circuit boards contain lead, both of which
are classified as hazardous waste and must be removed and handled according to local
regulations.
The S.B.C. division of the Parker Hannifin Company, together with local
distributors and in accordance with EU standard 2002/96/EC, undertakes to
withdraw and dispose of its products, fully respecting environmental
considerations.
Page 13 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
1.10 Warranty
The warranty duration if 1 (one) year. The converter must not be opened, accessed or modified
in any of its part. Any attempt to do so would cause the 1-year warranty to be cancelled with
immediate effect.. Parker Hannifin declines any responsibility for damages that may be caused
by inappropriate use of the converter.
2 PRODUCT INTRODUCTION
2.1 Product description
HiDrive is the result of in-depth research and development and of a longstanding hands-on
experience combined with a wide-ranging market research.
HiDrive focuses on the market of applications requiring a high degree of precision and accuracy,
high performance, flexibility to connect to various supervision and control systems, high torques
and custom drive arrangements based on specific applications.
HiDrive is a range of high performing, completely digital drives used both in closed-loop vector
control mode and as servo drive (available as standard). The range offering is complete in
several sizes, with 3-phase, 1-phase or continuous power.
The drive can be run in the following standard modes (usually called “operating modes”) , both
when it is used to control regenerative asynchronous motors or brushless motors: torque control,
speed, positioner with trapezoidal profile, variable ratio/phase control electrical shaft, electronic
cams, positioner via CanBus. These operating modes are available both in vector control and as
servo drive. The drive comes with many other standard functions, such as S ramps, value
capturing and comparison functions.
Only one parameter setting is used to chose an operating mode or to select between
asynchronous or brushless motor control.
The standard HiDrive is equipped with three independent encoder ports, to which the following
devices can be connected: resolver, incremental encoder, less wiring, sincos, sincos+absolute
Endat mono and multirun, sincos+absolute Hyperface mono and multirun. Also available are a
second incremental encoder or sincos or frequency/sign input, whereas encoder RS422 repetition
has a high maximum output frequency and programmable pulses per revolution.
In order to have more connection flexibility of HiDrive parameters with the external word
(inputs/outputs), the drive is provided as standard with a PLC (called “picoPLC”). The picoPLC
has a capacity of up to 256 instructions, scanning time of 6.144 ms, Ladder and Instruction List
programming languages. It is a very powerful tool to implement a simple per sequence logic in
the drive.
For complex applications, the drive can house (as option) a full-IEC1131 environment (called
“LogicLab”), that can be programmed using all 5 standard and multitasking languages (6 tasks
with different cyclic execution times).
The drive is equipped with 3 leds providing an immediate display of the drive status, also
without keypad on the drive. HiDrive can also be equipped with an optional removable
alphanumeric keypad with internal memory to display parameters, send commands, write
picoPLC instructions and providing alarm diagnostic functions. Through the keypad it is also
possible to “clone” parameters and picoPLC programs between drives.
Page 14 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
An advanced software tool (called “MotionWiz”) is also available free of charge to be able to
connect the drive to the PC via serial link RS422 or RS232. Such tool allows to interactively
configure the drive, to program the picoPLC and to display the variables by means of a software
oscilloscope.
Besides the features described above, the drive comes complete with the following standard and
optional functions:
™ Automatic cogging compensation functions
™ High, adjustable resolution of position loop
™ Analogue inputs and outputs, digital inputs and outputs, relay outputs
™ Serial communication port RS232
™ Serial communication port RS422/485
™ CanOpen DS301 or SBCCAN Fieldbus (standard)
™ Three option slots
™ I/O Expansions (optional)
™ Profibus-DP Fieldbus (optional)
™ Integrated EMI filter to HID8 (included)
™ Low voltage power supply
™ Separate 24Vdc supply to the control logic
™ Programmable power supply for motor feedback device
™ Encoder input voltage sensing to automatically compensate for any voltage drops in the
encoder supply due to the cable length
™ Dedicated motor braking driving port
™ PWM up to 16kHz
Page 15 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
2.2 Identification
The converters of the Hi-drive series are available in 13 models: HID2, HID5, HID8, HID10,
HID16, HID25, HID35, HID45, HID75, HID100, HID130, HID155 and HID250. The number
that follows the HID abbreviation corresponds to the rated current of the converter in amperes.
Use the following table to specify the order code:
HID
X
where:
HID
X
2
S
D
S
E
H
Y1
Y2
Y3
R
M
2
5
8
10
16
25
35
45
75
100
…
S
D
S
E
H
Y1
Y2
Y3
R
M
Servodrive series
ATEX type drive
Drive size (nominal current, up to 3 digits: 2, 5, 8, 10, 16, 25, 35, 45, 75, 100, 130, 155,
250)
SBC CAN protocol (standard)
CANopen protocol (DS402)
Second encoder input for SinCos signals – 1 Vpp
Second encoder input for quadrature digital signals – RS422
Second encoder input for quadrature digital signals + Hall sensor signals
Code optional boards:
Optional P = profibus DP - P
board in I = I/O 8DI+8DO –I
Slot
E1 = Powerlink (n.a.)
N. 1
E2 = Sercos 3 (n.a.)
E3 = CIP (n.a.)
Optional E4 = Profinet (n.a.)
board in E5 = Ethercat (n.a.)
S = Sercos
Slot
D = Devicenet (n.a.)
N. 2
C1 = Robox board up to 1,5 axis (with CANopen DS402) [in 3 Slot]
Optional C2 = Robox board up to 4 axis (with CANopen DS402) [su 3 Slot]
board in C3 = Robox board up to 32 axis (with CANopen DS402) [su 3 Slot]
C4 = Robox board up to TBD (with CANopen DS402) (n.a.) [in 3 Slot]
Slot
C5 = Robox board up to TBD (with CANopen DS402) (n.a.) [in 3 Slot]
N. 3
C6 = Robox board up to TBD (with CANopen DS402) (n.a.) [in 3 Slot]
Internal safety relay
Memory area for ritentive variables
Page 16 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
A label is attached on the right side of the converter that contains all the essential information to
correctly identify the unit:
ƒ Serial number
ƒ Model
ƒ Nominal plate data
It is important to refer to this label before requesting any kind of technical information from
Parker Hannifin S.p.A S.B.C. Division
An examle of this label is given below.
Side to detach
This part is at user disposal.
Every model is identified in the label and the handbook from acronym "HID" (Hi-drive series)
followed from a number, which represents the nominal output current of the apparatus.
Every label identifies:
Page 17 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
3 TECHNICAL DATA
3.1 Ambient conditions
operation
storage
transportation
operation
storage
transportation
3K3 Class, 0 … +45 °C (+32 …+113 °F)
temperature
1K4 Class, -25 … +55 °C (-4 …+131 °F)
2K3 Class, -25 … +70 °C (-13…+158 °F)
3K3 Class, 5-85 % without ice and condensation
humidity
1K3 Class, 5-95 % without ice and condensation
2K3 Class, 95% a 40°C
altitude (*)
≤ 1000 m slm (≤ 3281 feet asl)
IP20 (only in close electric cabinet)
protection degree
UL open type equipment
pollution degree
2 or lower (no conductive dust allowed)
(*) For higher installation altitude, derate the output current by 1.5% each 100m up to 2000m
maximum
3.2 Vibrations and shocks
operation
(3M1 class)
transportation
(2M1 class)
frequency [Hz]
2≤f<9
9 ≤ f < 200
2≤f<9
9 ≤ f < 200
200 ≤ f < 500
amplitude [mm] acceleration [m/s2]
0,3
1
3,5
10
15
free fall 0,25m max
3.3 Available models
SIZE 1
SIZE 2
SIZE 3
SIZE 4
SIZE 5
SIZE 6
length [mm]
87
122
227
250
250
600
AVAILABLE MODELS AND DIMENSIONS
width [mm]
depth [mm] (*)
models
360 (428**)
227
HID2-HID5-HID8-HID10
360 (428**)
227
HID16-HID25
360 (428**)
227
HID35-HID45
660
320
HID75
720
365
HID100-HID130-HID155
1145
465
HID250
(*) without connector and keypad
(**) with fixing flange
Page 18 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
3.4 Power supply
Control stage
Supply voltage range
Max ripple
Current rating of the external power supply
Control electronics dissipation, max
EMC Filter
V=
Vpkpk
A
W
-
24V (-0%...+10%)
within the range
2
30
internal
Stationary brake
Supply voltage
V=
Max. current
A=
24 ±10%
1,8 (2 per HID155 and
HID250)
Power stage
Mains frequency
Frequency variation, max
Supply voltage
HID2-HID5-HID8-HID10-HID16HID25
Supply voltage
HID35-HID45
Supply voltage
HID75-HID100-HID130
Supply voltage
HID155-HID250
Maximum voltage unbalance
Hz
Hz/sec
V~(3-phase)
V~(1-phase)
V=
V~(3-phase)
V=
V~(3-phase)
V=
V~ (3-phase)
V=
%
50…60 ± 5%
1,2
200-10% ... 480+10%
200-10% ... 277+10%
282-10% ... 678+10%
200-10% ... 480+10%
282-10% ... 678+10%
380-10% ... 480+10%
500-10% ... 678+10%
380-10% ... 480+10%
500-10% ... 678+10%
3
Note that single phase AC supply is not allowed for HID35 up to HID250
The converter can be used only in grounded TT and TN industrial networks. Do not use in
ungrounded networks (IT) or in networks with asymmetrical grounding.
Page 19 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
3.5 Technical characteristics
SIZE 1
Rated output current
Peak output current (2 sec)
Continuous service installed load
Power stage dissipation
Switching frequency (selectable)
Default switching frequency
Current derating with fsw>fdefault
Current derating with Vmain>440V~
Output frequency
Internal fan capacity
Braking resistor
Continuous internal braking power
Braking power peak790Vdc
DC circuit capacity (±20%)
Continuous power
Braking threshold
Overvoltage level
Undervoltage level
EMC filter
SIZE 2
Rated output current
Peak output current (2 sec)
Continuous service installed load
Power stage dissipation
Switching frequency
Current derating with Vmain >440V~
Output frequency
Internal fan capacity
Braking resistor
Continuous internal braking power
Braking power peak790Vdc
DC circuit capacity (±20%)
Continuous power
Braking threshold
Overvoltage level
Undervoltage level
EMC filter
model
HID2 HID5 HID8 HID10
Arms
2
5
8
10
Arms
4
10
16
20
kVA
1,4
3,5
5,6
6,9
W
30
75
120
140
kHz 8-16
8-16
8
4
kHz
8
8
8
4
p.u.
0,7
p.u.
0,9
Hz
0 - 500
m3/h
32
47
63
63
ohm 200
90
75
75
W
75
75
120
120
W
3120 6935 8320 8320
sec
1
0,7
0,5
0,5
195
390
390
390
μF
W
See diagrams
Vdc
795 – 770 (-0V … +20V)
Vdc
870
Vdc
70% * √2 *Vmains
internal
Unit
Unit
Arms
Arms
kVA
W
kHz
p.u.
Hz
m3/h
ohm
W
W
sec
μF
W
Vdc
Vdc
Vdc
-
Page 20 of 233
model
HID16
16
32
11,2
220
HID25
25
50
17,5
350
8
0,9
0 - 500
168
40
180
15600
0,2
27
180
23115
0,15
585
See diagrams
795 – 770 (-0V … +20V)
870
70% * √2 *Vmains
external
Parker Hannifin S.p.A Divisione S.B.C
SIZE 3
Rated output current
Peak output current (2 sec)
Continuous service installed load
Power stage dissipation
Switching frequency
Current derating with Vmain >440V~
Output frequency
Internal fan capacity
Braking resistor
Continuous internal braking power
Braking power peak790Vdc
DC circuit capacity (±20%)
Continuous power
Braking threshold
Overvoltage level
Undervoltage level
EMC filter
Hi-drive User Manual
model
Unit
HID35
35
70
22,8
490
Arms
Arms
kVA
W
kHz
p.u.
Hz
m3/h
ohm
W
W
sec
μF
W
Vdc
Vdc
Vdc
-
HID45
45
90
28,5
540
4
0 - 500
260
13
400
48000
0,1
1800
See diagram
795 – 770 (-0V … +20V)
870
70% * √2 *Vmain
external
(✎)
SIZE 4 / 5
Unit
Rated output current
Peak output current (3 sec)
Continuous service installed load
Power stage dissipation
Switching frequency
Current derating with Vmain >440V~
Output frequency
Internal fan capacity
External braking resistor (minimum)
Continuous external braking power
(maximum)
Braking power peak790Vdc
DC circuit capacity (±20%)
Continuous power @400V~
Braking threshold
Overvoltage level
Undervoltage level
Arms
Arms
kVA
W
kHz
p.u.
Hz
m3/h
ohm
EMC filter
Fan supply voltage
Fan power
Internal mains inductance
HID75
75
135
53
890
272
13
kW
20
W
μF
kW
Vdc
Vdc
Vdc
48000
3150
41
-
model
HID100 HID130
100
130
180
234
70
91
1050
1300
4
0,9
0 - 400
459
459
10
10
25
25
62400
62400
5000
5000
55
72
790 - 770
870
400 - 440
internal
V~
-
W
µH
100
Page 21 of 233
HID155
155
232
110
1300
459
10
25
62400
5000
100
870
400
Restricted
Distr. - II amb.
25 m motor
cable
230 ±10%
(1ph, 50/60 Hz)
140
140
90
90
Parker Hannifin S.p.A Divisione S.B.C
SIZE 6
Rated output current
Peak output current (3 sec)
Continuous service installed load
Power stage dissipation
Switching frequency
Current derating with Vmain >440V~
Output frequency
Internal fan capacity
External braking resistor (minimum)
Continuous external braking power
(maximum)
Braking power peak790Vdc
DC circuit capacity (±20%)
Continuous power @400V~
Braking threshold
Overvoltage level
Undervoltage level
EMC filter
Hi-drive User Manual
Arms
Arms
kVA
W
kHz
p.u.
Hz
m3/h
ohm
model
HID250
250
375
180
3500
4
0,9
0 - 400
750
2.1 (BU option)
kW
200 (BU option)
kW
μF
kW
Vdc
Vdc
Vdc
270 (BU option)
9900
160
760 - 750
820
400
-
Restricted Distr.
II amb.
25 m motor cable
Unit
Fan supply voltage
V~
Fan power
W
External mains inductance
µH
230 ±10%
(1ph, 50/60 Hz)
200
0.075mH 350A
Cod.: LCG350_0,075mH
Page 22 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
3.6 Other characteristics
auxiliary encoder (opto-insulated)
Auxiliary encoder input
Max frequency encoder input
kHz
RS-422 encoder simulation output
steps/rev
Max frequency
kHz
input impedance
Input High voltage range
Input Low voltage range
Type of driving required
Reaction time
in quadrature
400
22…218
400
5 digital inputs (opto-insulated)
kΩ
V
V
μs
20 ± 5%
15...24
0...9
PNP
< 2,5
2 digital outputs open collector PNP (opto-insulated)
External supply
Vdc
5 – 24 (±10%)
Output High voltage range
V
> (Vsupply–1)
Output Low voltage range
V
<1
Max current for single output
mA
100
Overload / Short circuit protection
yes
pull-down internal
20
kΩ
rise time
≤ 200
μs
voltage
CMR
resolution
input impedance
max frequency
1 differential analog reference
V
dB
bit
kΩ
Hz
voltage
CMR
resolution
input impedance
max frequency
1 differential auxiliary analog input
V
dB
bit
kΩ
Hz
±10
>80
14 + sign
8.61kΩ ± 5%
500
±10
>80
10
8.61kΩ ± 5%
2 single ended analog outputs (referred to 0VA)
voltage
V
max current
mA
resolution
bit
Overload / Short circuit protection
voltage
max current
relay output (1 contact NO + 1 contact NC)
V
A
Page 23 of 233
500
±10
1,5
10
yes
24±10%
1
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
4 MOUNTING
4.1 Dimensions and weights
A
mass
Page 24 of 233
HID2
HID5
HID8
87mm
5.8kg
HID16
HID25
HID35
HID45
122mm
8.5kg
227mm
16kg
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
(✎)
Y
Z
mass
HID75
320 mm
660 mm
40 kg
HID100
365 mm
720 mm
59 kg
Page 25 of 233
HID130
365 mm
720 mm
59 kg
HID155
365 mm
720 mm
59 kg
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
HID250
A
Z
Y
A
Y
Z
mass
HID250
600 mm
465 mm
1145 mm
(1500 con BU)
100 kg
(108 kg with brake
unit – option)
Page 26 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
4.2 Fastening
Fasten the drive in the cabinet using the mounting holes on the mounting plate (see figure
below).
HID2-…-HID25
A – frame width
B – plate width
C – spacing
D
E
HID35-HID45
HID2-HID5-HID8
87mm
80mm
62mm
9mm
9mm
Page 27 of 233
HID16-HID25
122mm
115mm
62mm
26.5mm
26.5mm
HID35-HID45
227mm
219mm
150mm
34,5mm
38,5mm
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
HID75
HID100-HID130-HID155
Page 28 of 233
658
600
lr
-
-
300
- - t - - t - ·-
- - - - - - - -+----- - - - - · - ____
L / '---- - - - - - - - - - - - - - -
~------------
I
I
I
II
r
0
I
,----L-- • r-----
r...IOUNT I NG PANEL
· --------.
0
I
I
I
I
I
0- - - - - . ,
I
0 -
I
I
0 -
N
I
I
I
I
0
I
o-,
N
'~~~/----:2-j-
=
0
0
o-
I
N
~
I
I
' ,
I
L __ I __ _
I
'
DATUM
•s •
\
:1
o----L
----------\---------------------j
I
L~-~~~~~~~~~~~~~~~~~~~
L
--------------
6 POSITIONS
600 TYPICAL CUBICLE
HID250
I
"'"'
o---r
N
Parker Hannifin S.p.A Divisione S.B.C
I
340
575
10 POSITIONS SU I TABL E
L__F_OR_M_B_F_I_X_I_NG_S_ __
TYPICAL CUBICLE
OUTL INE
Page 29 of 233
Hi-drive User Manual
185
135
18
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
4.3 Mounting instructions
IMPORTANT
IMPORTANT
IMPORTANT
• The converter must be mounted vertically with the power block above.
• It is necessary to leave a minimum free space of 100 mm above and below the
converter in order to ensure a sufficient drive cooling air flow. The figure
shows how to cool hot air in order to avoid condensing that might damage
electronic components: air cooling operations must be performed outdoor or in
an environment separated from the drive location.
• The air flow coming into the converter shall not come from or by other heatgenerating components.
• Ensure a good ventilation within the electric cabinet.
Page 30 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5 ELECTRICAL CONNECTIONS
5.1 Connector pin-out
HID2 - … - HID25
top view
X1
X2
X3
Hi drive
STATUS
LED
X4
X7
X8
X5
X9
X10
X6
X11
bottom view
front view
Page 31 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
top panel.
CID
3 ~
4~
5~
6 CID
i===i
CID
7~
8
CID
©
X2
1
'~
I~
I-
I~
1
ciiJ
'====
CID
'====
CID
~
r=
\'!)
2
@
3
@
@
4 '===
X3
----..-.
---..
+
RP
3 RN
4 IN
5 BRC
2
6 L 1
7 L 2
8 L 3
---
-
-
X2
..-
--
--
---::
1
2
3
4
1
2
.::
-
3
-::
4
u
v
w
PE
+24Vdc BR
BR
BR +
OVdc BR
X3
Page 32 of 233
BRAKE
CID
~
1 0[
POWER SUPPLY
2
--..
MOTOR
1 [!]
X1
stationary
Xl
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
HID35-HID45
X1
X2
X3
X4
STATUS
LED
X5
X6
X7
Page 33 of 233
X8
X9
X10
X11
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
Terminal block
X1
1
DC+
2
RP
3
RN
4
IN
5
BRC
6
L1
7
L2
8
L3
9
PE
Terminal block
X2
1
U
2
V
3
W
4
PE
Terminal block
X3
24 Vdc
1
3
BR+
0V
4
2
BR-
Page 34 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
HID75-HID100-HID130-HID155
X3
X4
LED
STATUS
X6
X7
X8
X9
X10 X11
X5
terminal
protection
cover
X1 – X2
Page 35 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
Terminal block X1 e X2 (remove the protection panel to access to the terminal block)
HID75
Terminal block
X1
PE
X2
Bra. Res.
1
2
3
4
5
1
2
3
1
2
L1
L2
L3
DC+
DC-
U
V
W
BR+
BR-
X2
4
PE
motor
HID100 – HID130 – HID155
Terminal block
Fan
X1
Auxiliary
fan supply
1
L1
2
L2
3
L3
X2
4
DC+
5
DC-
1
U
2
V
Bra. Res.
3
W
1
BR+
X1
X2
PE
4
PE
motor
(✎)
Page 36 of 233
2
BR-
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
HID250
LED
STATUS
X3
X4
X5
X11
X6
X10
X8
X7
X9
Page 37 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
Front panel
9 poles female Sub-D
X4 RS232
1
2
3
4
5
6
7
8
9
Reserved
RX
TX
Reserved
0VF
Reserved
Reserved
Reserved
Reserved
Terminal block
X5
0VQ drive
supply
+24V drive
supply
power
power
GND (DIGITAL)
OUT 1
OUT 0
VDC (DIGITAL)
GND IN
IN 3
IN 2
IN 1
IN 0
15
1
16
2
17
18
19
20
21
22
23
24
25
26
27
28
3
4
5
6
7
8
9
10
11
12
13
14
9 poles female Sub-D
X6 “resolver”
1
2
3
4
5
6
7
8
9
PTC
A GND
ECC SIN COS PTC
ECC +
SIN +
COS +
Page 38 of 233
– SR drive enabled
+ SR drive enabled
SC B
SC A
IN 4
0VA
MON 2
MON 1
0VA
– AX
+ AX
0VA
– REF
+ REF
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
For HID2-…-HID25 bottom panel, for HID35-HID45 front panel
15 poles female Sub-D
X7 “sincos”
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PTC
SHIELD
A GND
SENSE +
CLK +
DATA +
B+
A+
PTC
Ve
SENSE CLK DATA BA-
9 poles female Sub-D
9 poles female Sub-D
X9 “encoder input”
X8 “RS422/485”
1
2
3
4
5
6
7
8
9
TX422 +
RX422 +
TX422 RX422 SHIELD
Termination
N.C.
N.C.
0VF
1
2
3
4
5
6
7
8
9
9 poles male Sub-D
9 poles male Sub-D
X11 “CAN”
X10 “encoder output”
1
2
3
4
5
6
7
8
9
EOUTA +
EOUTA EOUTB +
EOUTB EOUTC +
EOUTC 0VF
Reserved
Reserved
EINA +
EINA EINB +
EINB EINC +
EINC 0VF
SHIELD
+5VF
1
2
3
4
5
6
7
8
9
Page 39 of 233
N.C.
CAN_A-L
GND CAN_A
CAN_B-L
SHIELD
GND CAN_B
CAN_A-H
N.C.
CAN_B-H
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.2 Cable lengths and cross sections
Chose a cable for flexible or static installation depending on the application.
See the table below for cable sections:
Model
MOTOR
(X2)
Section
NETWORK
(X1)
Section
Tightening
torque
HID2
1.5mm2
(AWG14)
2mm2
(AWG14)
HID5
1.5mm2
(AWG14)
(AWG14)
Section
Tightening
torque
NETWORK
External
resistor
Signal
(X5)
Stationary
(X3)
Fan supply
Section
Tightening
torque
braking Section
Tightening
torque
Section
Tightening
torque
brake Section
Tightening
torque
Section
Tightening
torque
Max. motor cable length
Max cable capacity
(AWG12)
HID10
2.5mm2
(AWG12)
2.5mm2
(AWG12)
0.5 – 0.6 Nm (M3)
0.22 ÷ 1 mm2 (AWG16)
0.22 – 0.25 Nm (M2)
1 mm2 (AWG16)
0.5 – 0.6 Nm (M3)
60 m
< 150 pF/m
Section
Signal
Tightening
(X5)
torque
Section
Stationary
Tightening
brake (X3)
torque
Max. motor cable length
Max cable capacity
MOTOR
(AWG12)
0.5 – 0.6 Nm (M3)
2mm2
2.5mm2
Tightening
torque
Model
HID8
2.5mm2
HID35
10mm2
HID16
4mm2
(AWG8)
HID25
6mm2
(AWG8)
1.2 Nm (M4)
4mm2
6mm2
(AWG8)
(AWG8)
1.2 Nm (M4)
HID45
10mm2
HID75
HID100
HID130
25÷50mm2 35÷95mm2 35÷95mm2
2.5 Nm (M5)
10mm2
10mm2
6 ÷ 8 Nm
15 ÷ 20 Nm
2
25÷50mm 35÷95mm2 35÷95mm2
(AWG6)
(AWG6)
(AWG6)
(AWG6)
2.5 Nm (M5)
10÷25mm2
(AWG6...AWG4)
(AWG3-4)
(AWG4)
6 ÷ 8 Nm
25÷50mm2
(AWG8)
(AWG1)
(AWG1)
(AWG2/0)
(AWG2/0)
15 ÷ 20 Nm
6÷8mm2
6÷8mm2
(AWG8)
(AWG8)
2.5 Nm (M5)
6 ÷ 8 Nm
0.7 Nm
2
2
0.22 ÷ 1 mm (AWG16)
0.22 ÷ 1 mm (AWG16)
0.22 – 0.25 Nm (M2)
0.22 – 0.25 Nm (M2)
1mm2 (AWG16)
0.22 – 0.25 Nm (M2)
2,5mm2 (AWG12)
0.7 Nm
60 m
50 m / 300 m with inductance
< 150 pF/m
Page 40 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
Model
MOTOR
NETWORK
Section
Tightening
torque
Section
Tightening
torque
External braking Section
Tightening
resistor
torque
Section
Signal
Tightening
(X5)
torque
Stationary brake Section
Tightening
(X3)
torque
Section
Fan supply
Tightening
torque
Max. motor cable length
Max cable capacity
HID155
HID250
2
35÷95mm (AWG1)
2 holes ø13mm
Separation
44mm
15 ÷ 20 Nm
2
35÷95mm (AWG1)
2 holes ø13mm
Separation 44mm
15 ÷ 20 Nm
6÷8mm2 (AWG8)
2 holes ø13mm
(BU option)
0.7 Nm
2
0.22 ÷ 1 mm (AWG16)
0.22 – 0.25 Nm (M2)
1mm2 (AWG16)
0.22 – 0.25 Nm (M2)
2,5mm2 (AWG12)
0.7 Nm
50 m / 300 m with inductance
< 150 pF/m
All signal cables must have a minimum section of 0.22 mm2.
The resolver cable must consist of 4 individually shielded twisted pairs protected by a shield.
The conductor-conductor capacity for the length used cannot exceed 10 nF and the section
cannot be less than 0.22 mm2. The maximum length is 60 m.
The motor cable must be shielded.
The cables used for analog signals must be shielded twisted pairs.
Shielded cables are also recommended for digital inputs and outputs.
For UL compliant installations, use only stranded copper wire rated for 75°C. Use only
appropriate crimping tools to fix terminal lugs. The conductors capacity shall be 125% of the
rated current accordingly to NEC 310-16.
Page 41 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.3 Protections
The drive has no protections against short circuits and overload on the mains side.
The user is responsible for short circuit and overload the protection as follows :
HID HID HID HID HID HID HID HID HID
2
5
8
10 16 25 35 45
75
Modello
Fuse size on AC power
supply network (delayed)
Fuse size on VDC
control power supply
Fuse size on fan supply
HID
100
HID
130
HID
155
HID
250
6A 10A 16A 16A 20A 50A 50A 75A 110A 175A 200A 250A 400A
3.15A fast
-
2A delayed
A thermo-magnetic switch can be used instead of fuses with the same effectiveness, but not in
installations with UL standard.
For UL compliant installations, use ultra-fast fuses accordingly to UL standard (RC, JFHR2).
See the following table:
Model
Mains AC
(3)
Brake
resistor
(2)
DC Bus
(2)
Model
Mains AC
(3)
Brake
resistor
(2)
DC Bus
(2)
HID2
HID5
HID8-HID10
HID16
HID25
Bussmann
FWP10A14F
Ferraz-Shawmut
A70P10-1
Bussmann
FWP10A14F
Ferraz-Shawmut
A70P10-1
Bussmann
FWP10A14F
Ferraz-Shawmut
A70P10-1
Bussmann
FWP20A14F
Ferraz-Shawmut
A70P20-1
Bussmann
FWP20A14F
Ferraz-Shawmut
A70P20-1
Bussmann
FWP20A14F
Ferraz-Shawmut
A70P20-1
Bussmann
FWP30A14F
Ferraz-Shawmut
A70P30-1
Bussmann
FWP20A14F
Ferraz-Shawmut
A70P30-1
Bussmann
FWP30A14F
Ferraz-Shawmut
A70P30-1
Bussmann
FWP-50B
Ferraz-Shawmut
A70P50-4
Bussmann
FWP30A14F
Ferraz-Shawmut
A70P30-1
Bussmann
FWP-50B
Ferraz-Shawmut
A70P50-4
Bussmann
FWP-60B
Ferraz-Shawmut
A70P60-4
Bussmann
FWP-35B
Ferraz-Shawmut
A70P35-1
Bussmann
FWP-60B
Ferraz-Shawmut
A70P60-4
HID35
HID45
HID75
HID100
HID130
Bussmann
FWP-80B
Ferraz-Shawmut
A70P80-4
Bussmann
FWP-80B
Ferraz-Shawmut
A70P80-4
Bussmann
FWP-80B
Ferraz-Shawmut
A70P80-4
Bussmann
FWP-100B
Ferraz-Shawmut
A70P100-4
Bussmann
FWP-80B
Ferraz-Shawmut
A70P80-1
Bussmann
FWP-100B
Ferraz-Shawmut
A70P100-4
Bussmann
FWP125A
Ferraz-Shawmut
A70P125-4
Bussmann
FWP-80B
Ferraz-Shawmut
A70P80-4
Bussmann
FWP175
Ferraz-Shawmut
A70P175-4
Bussmann
FWP200A
Ferraz-Shawmut
A70P200-4
Bussmann
FWP-100B
Ferraz-Shawmut
A70P100-4
Bussmann
FWP250
Ferraz-Shawmut
A70P250-4
Bussmann
FWP225A
Ferraz-Shawmut
A70P225-4
Bussmann
FWP-100B
Ferraz-Shawmut
A70P100-4
Bussmann
FWP300
Ferraz-Shawmut
A70P300-4
Page 42 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.4 Protective Earth connections
Minimize the length of the individual ground wires by placing grounding bar as close as possible
to the converters.
The grounding bar must be a copper bar and must be installed in contact with the cabinet metal
frame. The table shows the minimum dimensions depending on length.
Length (m) Width (mm) Thickness for HID2…25 (mm) Thickness for HID35,45 (mm)
0.5
20
6
8
1
40
6
8
1.5
50
6
8
Use only stranded copper wire rated for 75°C minimum
PE
BAR
PE
For the model HID2 up to HID45 use e a minimum wire section of 10 mm2 for grounding.
For HID75, 100 and 130 connect the ground wire to the PE pin of X1 terminal block with the
following cross sections / tightening torque :
Model
Section
Tightening torque
HID75
25÷50mm2 (AWG4)
6 ÷ 8 Nm
HID100-HID130-HID155
35÷95mm2 (AWG1)
42 Nm
HID250 (*)
N.4 bolts with washer
(supplied loose)
(*) Per HID250, don’t use the eyebolt to realize the ground connection/PE. Replace eyebolt with
bolt.
Page 43 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.5 Power stage supply connection
The converter can be used only in grounded TT and TN industrial networks, suitable for use on a
circuit capable of delivering not more than 5000 RMS symmetrical amperes, 480V maximum.
Do not use in ungrounded networks or in networks with asymmetrical grounding (IT).
5.5.1 Connection to AC 3-phase network
For HID75:
To use of EMC filter see the “size 4/5 table” to chapter “technical characteristics”
Page 44 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
For HID100, HID130 and HID155, see par. “external power supply (fans)” too:
To use of EMC filter see the “size 4/5 table” to chapter “technical characteristics”
Per HID250, see par. “external power supply (fans)” too. Connect the mains inductance (see the
“size 6 table” to chapter “technical characteristics”):
L3
L2
L1
To use of EMC filter see the “size 6 table” to chapter “technical characteristics”.
Page 45 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.5.2 Connection to AC 1-phase network
X 1
1
2
3
4
5
6
7
8
DC+
RP
RN
IN
BRC
L 1
L 2
L 3
~
( Ill
FUSE
EJ
EJ
EMC
( I~
(]J)J
FILTER
Page 46 of 233
L
N
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.5.3 Continuous supply connection
For HID75:
Page 47 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
For HID100, HID130 and HID155, see par. “external power supply (fans)” too:
For HID250, see par. “external power supply (fans)” too:
Page 48 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.6 External Power supply (fans)
HID100, HID130, HID155 and HID250 series need an external auxiliary power supply (220V
ac), needed for the internal fans.
This external supply must be connected to the auxiliary fan terminal block, indicated as
“auxiliary supply (fan)”.
Per HID250:
L
N
E
115V AC/230V AC
Fan Supply
Page 49 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.7 Motor connection (MIL connector)
5.7.1 Motor without stationary brake
Instead of the MIL connector (used in the
drawing), the following connector types can
also be used:
interconnectron -
terminal block
Per HID250:
Page 50 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.7.2 Motor with stationary brake
Terminal block X3 requires a dedicated 24VDC to terminals 1 and 4. Do not use the same supply
of the control stage. Terminals 2 and 3 control the brake through a static relay.
WARNING
Controls the output controlling the stationary brake of terminal block X3 (pin 2
and 3), managed as a command ON/OFF from drive with internal bit (b42.8).
The brake block-release function in all operating conditions must be performed by
the user.
terminal block
Instead of the MIL connector (used in the
drawing), the following connector types can also
be used:
interconnectron -
(*) the length of twisted pairs
of the brake depends on the
drive model (up to HID 25 is
20cm, for the other models
the length is greater).
Page 51 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.8 External braking resistor connection
The converter is equipped with internal braking resistor, except HID75, HID100, HID130 and
HID155 that have inside the braking transistor only (see “technical data” section). Per HID250
the brake unit (*) is an option.
Per the drives equipped of internal braking resistor, an external braking resistor can be used if an
higher braking power need to be handled.
The external braking resistor must have the same [Ω] value as the internal one. Install a bipolar
thermo-magnetic switch (or a fuse pair) between the resistor and the converter (see “dynamic
braking” section).
The maximum cable length for the external braking resistor is 3 meters.
For HID2 … HID45 models, remove the jumper between terminals IN and BRC (X1 terminal
block) and connect the external resistor between terminals RP and BRC.
For HID75, HID100, HID130 and HID155 use the “Bra. Res.” terminal block and connect the
external braking resistor to BR+ and BR- as follows:
During operation, the external resistor reaches high temperatures. Let the external
resistor cool down before performing any operation on it.
Page 52 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
(*) BU brake unit for HID250; the external braking resistor must be connected between DC+
bar and DBR bar of the BU module:
DBR
The brake unit is optional. However, it is possible to retro-fit a brake unit should the need arise.
There are three brake units, one for each drive frame size.
The brake units have the following specification:
Operating voltage:
750 - 820Vcc
Maximum duty cycle:
30%
Maximum on time:
20 seconds
Continuous duty:
30% of constant torque drive rating
The original exhaust duct supplied with the drive or the exhaust duct with the brake unit may be
used in the final installation.
The brake unit consists f the following parts:
− Exhaust duct
− Heatsink & IGBT assembly
− Control cable
− Brake connection plates – 1 set for type 8/9 and 2 sets for type 10
− Heatsink fixings
Page 53 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
− Brake unit cover and retaining nuts
− Earth bonding bracket
The brake uniti s shipped in a pre-assembled state (except for the connection plate(s)). It is
recommend that this assembly is carefully studied prior to installation within the cubicle. We
also recommend that the brake unit heatsink/IGBT assembly is removed from the exhaust duct
before installing the unit within the cubicle.
1.
2.
3.
4.
Remove the brake unit cover.
Remove the earth bonding bracket from the heatsink.
Loosen heatsink clamps.
Remove the heatsink/IGBT assembly and carefully piace it on a clear flat surface – take
care not to damage the heatsink fins.
5. If retro – fitting the brake unit to an existing exhaust duct then: Remove the exhaust duct
aperture cover and screws. Transfer heatsink clamps and screws from shipping brake duct
to existing drive duct.
6. Remove the drive's top front cover (plastic) via 2 off ¼ turn fasteners at top of drive.
7. Remove drive top cover which is attached via 4 off M5 screws on the side and 2 off M5
screws on the top. Care should be taken to prevent the cover from falling into the drive
and damaging the internal components. If fitting a new exhaust duct assembly, fit the
duct assembly into the top panel and secure to drive with 4 off M5 screws. Secure to the
mounting panel with M8 fixings.
8. Install brake unit IGBT/heatsink assembly within exhaust duct and tighten clamps. Take
care not to damage components on the PCB with handtools.
9. Connect brake unit control cable to the 14 way bulkhead connector at the top of the drive.
10. Secure the brake connecting plate(s) to the phase joining tabs of the drive top phase
(M3/U) and the phase joining tabs on the brake unit with M5 screws provided. Tighten to
4Nm (3ft/lbs).
11. Fit earth bonding bracket to heatsink and duct connection/earthing screws (M5) to
exhaust duct. Tighten to 4Nm (3 ft-lb). Note – This connection must not be omitted a
sit is required for safety reasons.
12. Replace drive top cover, exercise care to not damage brake connection plates with the
top cover as this will compromise the electrical insulation. Tighten 4 off M5 screws
on side of drive and 2 off M5 screws on top of cover to 2.5 Nm (1.84 ft-lb).
13. Replace drive front top cover with 2 off ¼ turn fasteners.
14. Fit brake unit cover with M6 captive washer nuts.
Page 54 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.9 Control stage supply connection
IMPORTANT
The drive electronics - including powering-up and switch-off operations - is
supplied at 24VDC.
The 24V power supply must be exclusively dedicated to the drive power supply . Sharing the
power supply with other devices (e.g. brakes, electro valves, etc.) could cause malfunctions.
For HID35 and HID45 models is necessary to insert a ferrite on the +24V voltage supply. Use
Wurth 742-711-32 model (see picture) or equivalent.
Page 55 of 233
Page 56 of 233
digital
outputs
~-:~
N.D.
N.C.
re lay output [::
GND connon --20
[
OUT 2 OUT 1 -
21
22
VCC supp Iy vo Itoge-- 23
24
digi tal
inputs
[
GI<U
IN
+24 VDC
I
l~
-28
1
ov
2 ---------- t 24 VDC
~ har dware
enab le
~ so fty reIoy
(opt i ono I )
J ---------~ ~f ~
S6789-
IN4
0 VA connon
nonitor 2
nonitor 1
0 VA connon
10
~~
11-~
12 -
0 VA contion -
13
1 4 -~
J
J
J
anaIogue
outputs
- AX
t AX
_ REF
t REF
ouxi I iory
onologue
input
no 1n
?nologue
1nput
Parker Hannifin S.p.A Divisione S.B.C
OVQ - - 1 5
+24 VDC
16
Connon ,----------1 7
control stage [
supply
Hi-drive User Manual
5.10 Analogue and digital I/Os connection
tErninol block XS
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
Main analog input:
1
Number
±10V differential
Range
8.61kΩ ±5%
Input resistance
14 bit + sign
Resolution
2 kHz
Maximum frequency
Auxiliary analog input
1
Number
±10V differential
Range
8.61kΩ ±5%
Input resistance
10 bit
Resolution
800 Hz
Maximum frequency
ANALOG INPUT
DIGITAL INPUT
Digital inputs
5 opto isolated
Number
15 ÷ 24V
High voltage range
0 ÷9V
Low voltage range
20kΩ±5%
Input resistance
=2.5μs
Reaction time
Type of driving
PNP
required
ANALOG OUTPUT
Analog outputs
2
Number
±10V
Range
1kΩ
Output resistance
10 bit + sign
Resolution
1.5mA
Max. output current
Yes
Short circuit protection
Yes
Overload protection
DIGITAL OUTPUT
Voltage supply
Digital outputs
2 opto isolated
Number
PNP open collector
Type
External digital power
5 ÷24Vdc
supply
=200μs
Rise time
Vpower – 1.0 V
VH
-0.5 ÷ 1.5V
VL
100mA
Max. output current
Yes
Short-circuit protection
Yes
Overload protection
Relay output
Number
1 (NO - NC)
Voltage
24V
Max current
1A
Page 57 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.11 Feedback connection
5.11.1 Resolver
Instead of the MIL connector (used in the drawing),
the following connector types can also be used:
interconnectron -
terminal block
When the resolver is connected, no incremental encoders can be used on connector X7.
Page 58 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.11.2 Incremental encoder
Instead of the MIL connector (used in the drawing),
the following connector can also be used:
interconnectron
Page 59 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.11.3 Sinusoidal encoder
Page 60 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.11.4 Sinusoidal encoder + EnDat
As far as the cable is concerned, you may use a Heidenhain cable or one with the same features.
Cables without “SENSE” must not be longer than 20 metres, cables with “SENSE” shall have a
maximum length of 60 metres.
Page 61 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.11.5 Sinusoidal encoder + Hiperface
Note: the drive require the signals sin+ and sin – inverted, as showes in the diagram above.
Page 62 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.11.6 Incremental encoder + hall sensor
Page 63 of 233
Hi-drive User Manual
8+-
8 - A+
~~
If \ \
I I ) _l
5.11.7 SinCos (one sinwave per pole pitch)
I
I
) j
I \
/
A-
Parker Hannifin S.p.A Divisione S.B.C
I
PT CPT[
OV
5 Vdc
\
\
I
\
I
\_/
1
I
1
1
X
X
0 5
0 .5
\
\
\
~
b l u /nero
rosso / ne r o
I \ verde / ne r o
/ \ _g i o l lo / ne r o
./
\
v i o l etto
g i o I lo
gr ig io
rosa
verde
narro n e
b lu
nero
b i anco
b lu
b i anco/ verde
I norro ne / ve r de
\\
I
\J
1
14
7 - 8+
88 - A+
15
A2 - SH IELD
g -
PTC+
l - PTC-
3 -
A
G ~~ O
10 -
VE
Page 64 of 233
H i - Dr i v e
Tern i n o l X7
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.12 Auxiliary encoder input connection
Page 65 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.13 Connecting converters to the electrical shaft
The example diagram above shows the connection of two converters to the electrical shaft with a
master, but the link could be extended to several converters connected in series.
The line termination resistors must be connected to the last converter. The master can be either
an encoder or an encoder simulator of another converter. However, the master encoder signal
must be a differential 5V RS-422 signal.
If the master is a Hi-drive type converter, you can connect up to 32 converters to the electrical
shaft by using the same signal of the simulated encoder (standard RS-485).
Page 66 of 233
Parker Hannifin S.p.A Divisione S.B.C
5.14
Hi-drive User Manual
Serial connection RS422/RS485
The serial link can be configured as either RS-422 or as RS-485 depending on how the
connection is made. If there are several converters connected to the same line, only the last node
must be terminated as shown in the diagram below. The two configurations are shown in the
diagram below.
Page 67 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.15 Serial connection RS232
5.15.1 Without converter RS232/RS422
The diagram below shows the connection between drive and PC by a Hyperterminal link based
on an ASCII protocol on the serial port RS232 (X4 of the drive):
5.15.2 With converter RS232/RS422
The diagram below shows the connection between drive and PC by a serial link RS232/RS422
based on S.B.C. protocol (X8 of the drive):
Page 68 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.16 CAN Bus connection
A CanBus interface based on the physical layer ISO/DIS11898 is included on the converter. The
Data link layer is the full CAN version 2.0 part A (ID 11 bit).
OL
0
(\J
~
z:
0
<(
u
u
('J
['--.
~L----1
X
I
u
u
('J
['--.
_j
z:
<(
,...--
<(
l_j
0
"'
~r-
->------1
X
z:
0
<(
u
u
('J
['--.
r:=::
>
I
~>--------1
~>--------1
'----OL
2:
z
0
-
(\J
w
_j
z
<[
u
~
rrl
v-
Ck
X
X
~
<[
I
z
<[
u
Page 69 of 233
u
>
0
w
D
D
z
-H--------1
_j
<(
~
1'--t--
z:
<(
Vl
X
'....__
f--
-c
>
z:
<(
X
co
I
z
~r--------1
'-----
=
D
D
"'
v-
(/)
-
~
X
X
r:=::
w
>
I
_j
z:
<(
w
D
D
z
Parker Hannifin S.p.A Divisione S.B.C
5.17
Hi-drive User Manual
Electro-magnetic compliance
In order to meet the requirements of EMC product standards (EN61800-3), the drive must be
installed in strict compliance with the instructions below.
Because of strong PWM voltage fronts caused by the converter, high capacitive currents can
sometimes circulate through couplings in the grounding systems (conductive noise). High
frequency disturbances are also possible, especially from motor cables, in the form of radiated
emissions.
Radiated and conductive disturbances can be reduced or prevented through:
9 grounding,
9 shielding
9 filtering, so as to reduce both the conductive interference in the cables and the return
conductive interference to the source (frequency converter) by using paths with the lowest
possible impedance. In this way other systems connected to the same electrical line are
protected effectively and the frequency converter will also be protected from the
interference of other systems.
5.17.1 Grounding
Two different grounding systems are used in the electric cabinets where the converters are
usually installed:
-
The EMC grounding, or HF (high frequency) reference, which is the uncoated
metal surface where drives and filters are installed.
-
The safety or PE (protective earth) grounding according to EN60204-1.
Install converter, network filter, 24V power supply etc. on the metal surface so as to ensure the
maximum possible electric contact (HF connection) between the zinc-coated steel sheet and the
converter’s (rear) mounting plate.
Page 70 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.17.2 Connection cables and shielding
Except the mains-filter cables, all other power and control cables must be shielded and kept
separated (min. distance between cables 20 cm). Where control cables must cross power cables
make sure they are at an angle as near 90° as possible.
Shielded cable screens shall be free and grounded on a copper bar by means of a connection
provided with cable gland (360º connection) as shown in the drawing, in order to ensure an
appropriate conductivity.
The motor cables and the power cables can never run parallel.
Connection 360°
Usually the screen is connected on both ends. In some cases, however, the control cable screen
(resolver, encoder, I/O, low voltage power supply, serial link) may be connected only on one end
when the current in the screen causes noises to the shielded cable signal.
The input cable must be connected to the PE grounding by means of a screw connection so as to
ensure a proper contact between the screen and the grounding.
The power section (converter) and the control section (PLC or CN) must be kept separated by a
division in the metal base. Connect the panels in the electric cabinet by means of a copper strap.
Never route noise-emitting cables in parallel with “clean” cables
Never route cables in parallel, especially near the filter (ensure sufficient distance)
Never route cables in loops (cables should be kept as short as possible and be close to the common
potential).
It is particularly important to keep mains cables away from motor cables. If the motor is
provided with emergency braking, keep the brake connection and power cables away from the
other cables (resolver and signal).
Page 71 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.17.3 Filters
The drivers are the components for use in the second environment (industrial environment) C3
category according to EN61800-3 (Adjustable speed electrical power drive systems. Part 3 :
EMC product standard including specific test method), with anti-noise filter and installed
according to recommendation of this manual. These products used in first environment (domestic
environment), may cause radio interference dangerous for the other devices: the user must be
required to take adequate measures with additional filter.
Many models of HID series have an internal filter, while for other models it’s necessary to use
an external filter, as specified in the following table:
model
EMC filter
HID2-HID5-HID8-HID10
HID16-HID25
HID35-HID45
HID75-HID100-HID130
HID155
HID250
internal
external
external
internal
internal
internal
Motor cable with Motor cable with
internal filter
external filter
30 meters
60 meters
60 meters
60 meters
30 meters
60 meters
25 meters
60 meters
25 meters
60 meters
The mains filter must be installed as close as possible to the converter and on the same panel as
the drive, ensuring a large contact surface with the electric cabinet or with the mounting
platform.
If the distance is over 30cm, the filtering effect decreases and a shielded cable must be installed
between the filter and the converter.
The filter ground lug must be connected to the ground bar with a connection as short as possible.
For HID16-HID25 and HID35-HID45 is available a footprint filter (see manual “EMC main
filter”).
Page 72 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
5.18 Cabling general layout
The following drawing show the details of the cabling layout, with particular attention to the
grounding of shielded cables.
The electric cabinet bottom must be electrically conductive , e.g. zinc-coated. Strip off any paint
coat to ensure contact. The grounding bar must be in contact with the cabinet bottom or ensure
an excellent electric connection and it must NOT be insulated. Route power cables away from
signal cables. The 24V input power cable must be shielded as well.
Hi drive
*Install the PE (Protective Earthing) grounding bar together with the HF bar o in order to prevent contact with the zinc-coating
bottom. Connect the two bars as shown in the diagram.
**Signal cables can be grounded either by means of a separate (HF) bar or directly connecting the (metal) cable glands to the
cabinet bottom (in this latter case, ensure that the PE bar is in contact with the cabinet zinc-coated bottom).
***The above diagram is to be considered as an overall view.
Page 73 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
6 STATUS LEDS
The converter is equipped with 3 led indicators.
When power is applied to the drive (24 VDC), if the drive’s electronics is working, the yellow
and green led come on.
The third led (red) provides converter status information as listed below:
- if it is off, the converter is shut off without active alarms.
- if it is on, the converter is enabled. the drive is in RUN mode
if it blinks with a pause after two series of blinks, the converter is disabled
IMPORTANT
and an alarm is active. The active alarm can be identified by counting the
number of blinks between the two pauses.
- if it blinks quickly and continuously, the I2t command is active and the
converter is still enabled.
7 SUPPLY MODE
(✎)
7.1 “Low voltage” supply
This procedure is for those situations in which the operator needs to work in close proximity to
the machine in a situation which could be potentially hazardous. In these conditions, the operator
must move the axes with a drive power supply voltage lower than the nominal rating (from 40 to
180V~, and from 57 to 255 VDC), so that the maximum allowable speed of the axes is also
lowered.
The motor is actually enabled approx.120ms after closing the contact that overrides the holding
charge resistance. This contact is activated when the internal continuous voltage in the drive gets
over 40VDC, provided that there aren’t any active alarms and that hardware and software
enabling commands are available.
In the same way, an under voltage alarm is generated when the voltage level falls below 40VDC.
The undervoltage fault automatic reset command is not active in this mode and b42.3 and b42.4
have no significance.
Low voltage power supply mode isn’t available for HID75, HID100, HID130, HID155 and
HID250 models.
Caution:
the switch between low voltage and high voltage modes is potentially dangerous
to the drive. Always switch between modes with the drive disabled and follow
these instructions step by step.
Page 74 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
o Low voltage to nominal operating voltage sequence.
a. Disable the drive. Wait 200ms.
b. Change the voltage from low to nominal.
c. Set bit b40.10 to 0
d. Wait 1.2s.
e. Enable the drive.
o Nominal operating voltage to low voltage sequence.
a. Disable the drive.
b. Set bit b40.10 to 1
c. Change the voltage from nominal to low.
d. Wait 200ms.
e. Enable the drive. The drive will be enabled after about 1.12s.
7.2 “High voltage” supply
In “high ” voltage operating mode (b40.0=0), the converter can supplied as follows:
-
AC 3-phase network (200…480 ±10%)
Set b39.0=0 (default).
The converter can automatically detect the power supply voltage rating and adapts
internal operating parameters accordingly. When the mains voltage is >440VAC,
b41.13=1 and output current is de. When one of the power supply phases is
missing, b42.4=1.
-
AC 1-phase network (200…277 ±10%)
Set b39.0=1 and set the peak nominal value of 1-phase supply (√2*Vphase-neutral) in
Pr21. Save, switch off and on again the converter.
With both modes of AC power supply, when parameter b42.3=0 the input power supply is on. In
case of power loss the bit is set to one, anticipating the converter’s “under voltage” alarm that is
based on continuous voltage.
-
Continuous (288…678 ±10%)
Set b39.0=1 and set the nominal value of continuous voltage in Pr21 . Save,
switch off and on again the converter.
The automatic reset of “under voltage” undervoltage alarm can be forced by b39.8=1 with any
kind of power supply.
Page 75 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
8 START-UP
In Its basic configuration, Hi-drive can control both synchronous permanent magnet motors
(brushless) and asynchronous induction motors. The setting of Pr31 can select either of the
following:
- Pr31=0
synchronous motor (default setting)
- Pr31=1
asynchronous motor
The drive is supplied with default factory parameter settings.
See the following chapters for use and start-up.
8.1 Setting the default parameters
When you carry out a default procedure, all factory parameters are changed and any previously
entered value is lost. In order to carry out the procedure, go through the steps below:
- supply 24VDC power to the drive (X5 pin 15 and 16);
- disable drive hardware b41.5=0;
- set the pico-PLC in stop, b39.13=0;
- command b42.12=1, in order to load the default parameters;
- save the data by commands b42.14 and b42.15 (the drive must be disabled);
- Save, switch off and on again the drive.
8.2 Selection of motor type
The first time the converter is powered up, or following a default command, the drive indicates a
“Def” condition (alarm Pr23=15).
In order to leave the drive’s initial condition, the operator shall have to input the motor data.
The parameters defining motor types are as follows:
Pr29
Number of motor poles
N.
Pr32
rated motor speed
r.p.m.
Pr33
rated motor current (ex. 2.5A, write 2.5)
A
Pr46
phase-phase motor resistance (ex. 1,8Ω, write 1.8)
ohm
Pr47
phase-phase motor inductance (ex. 2.6mH, write 2.6)
mH
Pr60
number of resolver poles
N.
With asynchronous motors, the values above shall be supplemented with the following
parameters:
Pr45
base speed
r.p.m.
Pr48
slip
r.p.m.
Only asynchronous motors
Pr49
magnetizing current
A
Pr32
motor limit speed
r.p.m.
After setting the parameters that identify the motor, the operator shall enter a data save
command, b42.15 (with drive disabled, b41.5=0). The drive will set the values of parameters
Pr2, Pr3, Pr16, Pr17, Pr18 and Pr19 through its internal logic. The automatic calculation of the
above listed parameters is performed only of the drive is in the default condition (alarm 15).
Page 76 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
8.3 Changing motor data
After having entered a data save command, no other changes shall be made to the motor
parameters . In order to change the entered parameter values (new motor), enter command b42.1.
The drive shall return to its default condition and changing motor data shall be enabled again.
Repeat the data save procedure with command b42.15 (with drive disabled) if you want to
recalculate parameters Pr2, Pr3, Pr16, Pr17, Pr18 and Pr19 with the new motor data.
8.4 Setting feedback
A key feature of Hi-drive is the ability to cope with several types of feedback, that can be used
simultaneously both as speed feedback and as position feedback, depending on the connection
and on parameter settings.
Speed and position feedback connections use three different connectors:
1.
2.
3.
A feedback, connection on input X6.
B feedback, connection on input X7.
C feedback, connection on input X9.
8.4.1 A feedback, input X6.
Input X6 can be used to link:
ƒ
Resolver
The input is dedicated to resolver read only. When this input is used, it must be identified as
speed feedback. In case of a space operating mode, the resolver can be also used as space
feedback.
8.4.2 B feedback, input X7.
Input X7 can be used to link:
ƒ
ƒ
ƒ
ƒ
Encoder sincos + EnDat interface
Encoder sincos
Encoder less wiring
Line drive incremental encoder RS422
Signal RS422 on this port does not require the line to be closed by resistors, as these are already
present inside.
When the resolver is connected to port X6, do not connect Less Wiring encoder and incremental
encoder to port X7.
Page 77 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
Input X7 has a variable power supply with either 5.8 or 12V voltage, selectable through
parameter settings. 5 and 8V voltage levels can be adjusted through a feedback from a sensing
pair cable to compensate for any voltage drop in the cables. When voltage is set at 12V, the
feedback is internal and any voltage drop in the cable cannot be compensated. Bit b64.0
indicates whether the sensing function is active; if it is not, the set voltage is adjusted in an
open loop.
8.4.3 C Feedback , input X9
Input X9 can be used to link:
ƒ
Line drive incremental encoder RS422
The connection of an encoder to this input requires line closing resistors to be provided, as
shown in the wiring diagram (“Auxiliary encoder input”).
Connector X9 has a 5V fixed input voltage insulated for the encoder.
8.4.4 Speed feedback configuration
In order to set the speed loop, select examples according to the table below:
Mode description
Resolver
b65.15=0 b65.14=0
-
SinCos + EnDat
b65.15=0 b65.14=1 Pr62=0
SinCos
b65.15=0 b65.14=1 Pr62=1
Less Wiring
b65.15=0 b65.14=1 Pr62=2
Incremental Encoder b65.15=0 b65.14=1 Pr62=3
SinCos + Hiperface
No. of
pulses
revolution
Input
-
X6
Pr58
b65.15=0 b65.14=1 Pr62=7
Vdc
5
8
12
X7
Encoder power
supply
b65.7=0 b65.6=0
b65.7=0 b65.6=1
b65.7=1 b65.6=0
Pr62=8
SinCos (One sin wave
b65.15=0 b65.14=1
(*)
per pole pitch)
Pr62=10
Incremental Encoder
b65.15=0 b65.14=1
(**)
+ Hall sensor
Incremental Encoder b65.15=1 b65.14=0 Pr63=3
Pr59
X9
Before selecting the system it is necessary to set the input voltage of the connected encoder.
The selection of power input voltage is only performed at the drive’s start up.
In order to enable the selected voltage, save the parameters, then switch off and on again the
drive. If you don’t, the previously selected voltage shall be effective until the next power-up.
Page 78 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
(*) if PRA, PRR or PRC motor is used, set the parameter Pr30=32767.
(**) if a motor of S.B.C. DIvision is used, set the parameter Pr30=8192.
8.4.5 Position feedback configuration
The same sensors used in peed feedback can be also used for position feedback.
The position loop feedback resolution is not fixed but can be controlled by parameter settings.
Parameter Pr169 performs this function and can have a value between 212 and 220 bit per motor
revolution.
The selection of position loop sensors and of the relevant resolutions can be made following the
table below:
The space in the drive is managed as a double word, with a ± 231 range. As a consequence, the
maximum value in motor revolutions for absolute systems will be:
± 2 31
spacemanaged =
Pr 169
Mode description
Resolver
b170.15=0 b170.14=0
-
SinCos +
EnDat
b170.15=0 b170.14=1
Pr62=0
SinCos
b170.15=0 b170.14=1
Pr62=1
Less Wiring
b170.15=0 b170.14=1
Pr62=2
Encoder
b170.15=0 b170.14=1
Pr62=3
SinCos +
Hiperface
b170.15=0 b170.14=1
Pr62=7
b170.15=0 b170.14=1
Pr62=8
incremental
Input
none
X6
X7
Pr58
SinCos (One
sin wave per
pole pitch)
No. of
pulses
revolution
Vdc
Encoder power
supply
5 b65.7=0
8 b65.7=0
12 b65.7=1
b65.6=0
b65.6=1
b65.6=0
incremental
Encoder +
Hall sensor
incremental
Encoder
Important.
b170.15=0 b170.14=1 Pr62=10
b170.15=1 b170.14=0
Pr63=3
Pr59
X9
In order to prevent damage to the encoder, select the power supply voltage of the
connected encoder.
The selection of power input voltage is only performed at the drive’s start up.
Therefore, in order to enable the selected voltage, save the parameters, then switch
off and on again the drive. If you don’t, the previously selected voltage shall be
effective until the next power-up.
Page 79 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
(✎)
8.4.6
Digital filter per encoder
Using bit b65.8, b65.9 and b65.10, if is necessary, it’s possible to generate a digital filter to
“clean” the encoder signal, connected to the X7 feedback input. While using bit b65.11, b65.12
and b65.13, it’s generated a digital filter for the auxiliary encoder.
The table below shows the filters characteristics. Pay attention to motor speed in according to the
max frequency filtered, to not limit the motor speed.
Binary code
Minimum pulse time Max frequency
[nsec]
[kHz]
b65.10 b65.9 b65.8
b65.13 b65.12 b65.11
0
0
0
642.5
778
0
0
1
1142.5
437
0
1
0
1642.5
304
0
1
1
2142.5
233
1
0
0
2642.5
189
1
0
1
3142.5
159
1
1
0
3642.5
137
1
1
1
4142.5
120
8.5 Phasing procedure
Phasing is necessary when the speed loop feedback is via incremental encoder incremental or
SinCos, as these encoders do not provide the absolute positioning on the motor shaft. Phasing
must be performed any time the drive is powered up.
The incremental encoder phasing does not allow to use the encoder simulator zero trace to set the
external control axis to zero, since the drive encoder simulation is not provided with a fixed
mechanical position in the motor revolution, but this is initialized any time a phasing command
is given.
During the incremental encoder operations the motor must be halted. If this type of feedback is
performed on the vertical axis, the phasing operations will be allowed only if the system is
balanced, that is if the vertical axis can be stopped without braking.
Before proceeding, consider that two phasing procedures are available, both requiring that the
motor can rotate even if it is installed inside the equipment (any emergency brake disabled).
Note that, in the first type of phasing procedure, the requested motor movement is larger then in
type 2 phasing. In type 1 procedure a cabling test is performed This procedure is therefore
recommended during the system’s fine-tuning.
Page 80 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
8.5.1 Type 1 phasing
It is activated by Pb64.2; the table below lists the parameters involved:
Par.
Pr58
Description
Enter number of steps by encoder revolutions. Encoder
connected to input X7. When b65.1=0, Pr58 is written in full
(*).
When b65.1=1, Pr58 is written exponentially (*).
Pr59
Enter number of steps by encoder revolutions. Encoder
connected to input X9. When b65.2=0, Pr59 is written in full
(*).
When b65.2=1, Pr59 is written exponentially (*).
Pb64.2 Phasing command 1. Disable software (Pb40.9=0); enable
hardware (Pb41.5=1), and driver OK (Pr23=0).
Execute the command: the motor executes two movements
and the last is about 90° degree electric, with control sign of
the encoder feedback. Introduce the correct number of the
motor poles (Pr29).
Pr76
Status:
0 if outcome is positive
2 if enable is not correct
3 if feedback is positive
4 if motor poles and/or number of steps are incorrect
5 if drive is not ready (Pr23≠0 or inrush open)
Pb41.6 Phasing outcome = 1 if procedure outcome is positive and it
is a necessary condition for drive OK (Pb41.4).
Field
W
±32767
1024
±218
W
±32767 1024
±218
0
R
R
(*) The sign “±“ indicates the direction of rotation: positive or negative feedback.
Page 81 of 233
Range Def.
0
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
8.5.2 Type 2 phasing
It is activated by Pb64.4; the table below lists the parameters involved:
Par.
Pr58
Description
Enter number of steps by encoder revolutions. Encoder
connected to input X7. When b65.1=0, Pr58 is written in full
(*).
When b65.1=1, Pr58 is written exponentially (*).
Pr59
Enter number of steps by encoder revolutions. A Encoder
connected to input X9. When b65.2=0, Pr59 is written in full
(*).
When b65.2=1, Pr59 is written exponentially (*).
Pb64.4 Phasing command 2. Disable software (Pb40.9=0); enable
hardware (Pb41.5=1), and driver OK (Pr23=0).
Execute the command: the motor executes a vibration, the
standing depends to the type of the motor and to the load.
Pr76
Status:
0 if outcome is positive
2 if enable is not correct (enabling procedure started by
Pb41.5=0 or Pb40.9=1)
5 if drive is in alarm or is not ready by the execution time
6 if parameter Pr271 deviates from its initial value by more
than 25 units. The calculated value can be saved. The saved
value will be considered as the initial value during the next
phasing.
7 if parameter Pr271 is over 200 units (maximum allowable
value). Recalculate value of torque.
Pb41.6 Phasing outcome = 1 if procedure outcome is positive and it
is a necessary condition for drive OK (Pb41.4)
Field
M
Range Def.
±32767
1024
±218
M
±32767
1024
±218
0
R
R
0
(*) The sign “±“ indicates the direction of rotation: positive or negative feedback.
If the calculated value of Pr271 at the end of the procedure is saved, on any future start up, the
phasing algorithm shall be calculated based on the saved value. In so doing, if mechanical
conditions are unchanged, there will be only one vibration whose duration shall be as set in
Pr271.
Page 82 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
8.5.3 Pico-PLC phasing program
After having entered all the encoder setting data, the following program can be added to PicoPLC so that phasing is performed when the drive is enabled
41.6
41.4
40.9
41.5
41.4
41.6
91.4
SET 64.4
Or SET 64.2
SET 91.4
IMPORTANT
The phasing procedure cannot be performed in low voltage mode.
IMPORTANT
Never activate saving command while the drive is enabled.
8.5.4 Fine phasing
By incremental encoder feedback it is possible to enable the motor fine phasing procedure on the
encoder zero point dog.
A pre-requisite for this “Fine phasing” is that the incremental encoder has been mechanically
phased on the motor shaft. It is therefore essential not to disinstall the encoder, otherwise the
motor-encoder assembly will have to be rephased at the control desk.
At the completion of the incremental encoder phasing procedure (type 1 or 2), a fine phasing
function may be enabled on the encoder zero point dog.
The function activates at the following revolution when command b65.3=1 is entered. The status
of command b65.3=0 signals that the fine phasing has been performed.
With less wiring encoder feedback , the function is performed automatically.
Page 83 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
8.5.5 Phasing procedure for encoder with EnDat o Hiperface interface
The procedure of encoder phasing is not necessary with Parker Hannifin Divisione S.B.C.’s
motor, but when the system requires the phasing, the procedure 1 and 2 of the phasing is the
same for incremental encoder (see paragraph “phasing procedure”) and it must finalized as
follows.
With EnDat or Hiperface interface, single turn or multiturn, after the phasing is possible to save
this information so at every start up the phasing procedure isn’t necessary; for take it, to bring
the motor shaft in the position that Pr28=0, disable the drive and save with command b64.8=1.
After this command is necessary start again the drive.
Alternative to this procedure, disable the drive and disconnect the motor cable, the motor can
rotate even if it is installed inside the equipment (any emergency brake disabled), with motor is
available to supply a positive tension between phase B and C respect the phase A (it’s important
to verify that the phase-phase resistance limits the current to the rated value) so that the shaft
aligned (only for S.B.C. motor, for other type see the paragraph “ motor phases”), set the
command b64.8=1 and start again the drive.
8.5.6 Motor phases
In this paragraph is showed a procedure not necessary for the motors of the S.B.C. Division,
essential for the motor connection, because allows to find the motor phases (A=U, B=V, C=W).
The procedures shown in this document are dangerous for the operator
and could damage the motor under test. A qualified and trained
personnel with advanced skills in electronics and drive technology is
therefore needed, the operator must be sure that these procedures are
proceeding in safety condition.
Necessary instruments:
power supply 24Vdc with output current equal or higher to the rated current of the motor
under test. Verify that the phase-phase resistance of the motor limits the current at the rated
value with 24V voltage applied.
Necessary requisites:
motor free without load and inertia applied.
Procedure:
connect the positive pin of the 24Vdc supply voltage at one motor phase (assign name A at
this phase). Connect the negative pin at one of the other phases (at random). Feeding the
circuit, the rotor will turn and to assume a new position. Observing the motor shaft, move
the negative pin of the 24Vdc voltage on the other phase: if the rotor turns counterclockwise (watching frontally the drive shaft), the phase connected to the negative pin is
the phase C, otherwise if the rotor turns clockwise this phase connected to the negative pin
is the phase B (*).
Result:
after to have connected the motor and the device of feedback to the drive, the counter of
the feedback increases if the motor turns clockwise, and decrease if turns counterclockwise sense.
(*) To avoid to damage the motor winding, to power the circuit only for the necessary time.
Page 84 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
8.6 Speed control
SPEED LOOP: The main task of a converter is to control motor speed so that it follows as
faithfully as possible the speed request that is generally known as the REFERENCE. Faithfully
following the reference means that the motor speed should equal the reference in static
conditions and also that the motor speed is as equal as possible to the speed requested during
dynamic conditions. To carry out this task, the converter must know some of the features both of
the motor used and of the mechanical part attached to it. This information is communicated to
the converter by the so-called ADJUSTMENT PARAMETERS.
ERROR: The error is the difference between the reference speed and the motor speed. The error
size is used by the speed loop in order to evaluate the level of current to be supplied to the motor.
TORQUE: The current that circulates in the motor windings is transformed in torque, thereby
allowing the motor to accelerate or decelerate.
GAIN: Given the typical applications of the Hi-drive, any occurrence of the term gain in this
document is referred to the rigidity of the axis, better known as STIFFNESS. In order to better
illustrate what the term STIFFNESS means, let’s imagine a motor controlled by a converter with
a requested speed of zero. The motor shaft will appear still. However, if a torque is applied to the
shaft, this will demonstrate an angle proportional to the torque applied. Suppose we apply the
motor rated torque and measure the STIFFNESS in degrees. The degrees measured will be the
index of the quality of the regulator as parameterized. Of course this is not the only quality
index.
8.7 Speed control adjustment
WHAT IS NEEDED
In order to correctly adjust a Hi-drive converter an oscilloscope is required. A speed probe and a
current probe will be connected at “monitor output 1” and at “monitor output 2”on terminal
block X5 (Pin 8 and 7, whereas Pin 6 is “common”).
By default, the drive monitors the Pr0 on screen 1, and Pr35 on screen 2 (see the description of
key parameters and the section about programmable outputs).
See the chapter “Inputs and outputs” for the technical features of outputs. terminal block X5”
The drive configuration software MotionWiz includes an “oscilloscope” function that recreates
an oscilloscope via a serial link.
If it is not possible to use an oscilloscope, a more approximate but applicable adjustment method
will be illustrated at the end of this section.
Page 85 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
BEFORE BEGINNING
Study the diagram below carefully (Fig. 1):
This diagram shows the response of the system to a square wave speed reference. Channel 1
(Ch1) represents the speed and channel 2 (Ch2) the current of the motor.
ESTIMATING Pr16
Before enabling the converter, the user should estimate the value of Pr16. The value of Pr16 is
what defines the gain of the system. To convert the value of Pr16 into grades per rated torque,
the formula to be used is the following: α =
Pr 33 *100
⋅ 28 where α represents the stiffness and
Pr16 * Ipd
Ipd is the peak current of the drive. Before using the formula, Pr33 must be set with the correct
value of the rated motor current . To evaluate the correct value of α, let’s consider that, if the
mechanical part to be moved is stiff (non-flexible) and if there is no transmission play, the
optimal stiffness would be about 4 degrees. If the mechanical part is not stiff enough, it could be
necessary to reduce the gain. If the motor torque has been sized in order to obtain a strong
acceleration, but the disturbing torques are very low during operation, it is possible to choose
stiffness angles of 20, 30 or 40 degrees, thereby maintaining acceptable performance. If it is
difficult to choose the proper stiffness angle, the user can begin with 10 degrees that is the
default adjustment if a motor with the same rated current as the converter’s is used.
At this point, let us set Pr16 to the estimate and enable the axis with a square wave reference.
Page 86 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
Select the width and frequency of the reference with care in order to avoid problems if the axis
has a limit switch. If we look at the oscilloscope we will see that as Pr17 varies, the response will
change. For decreasing values of Pr17, the response of the system will be as shown in figure 2
below:
For increasing values of Pr17, the response of the system will be similar to what is shown in
figure 3 below:
Page 87 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
The optimal value of Pr17 will be attained with a response of the system as shown in figure 4
below:
An overshoot of about 10% must be obtained. It is important that after the overshoot, an
undershoot does not occur.
Once the optimal value of Pr17 has been established, we must analyze the movement of the axis.
if it moves without vibrations and acoustic noise, the adjustment of the system is complete.
Otherwise, we must repeat the preceding procedures with lower Pr16 values.
In some applications it is possible to reduce acoustic noise by using a higher value in Pr18.
Figure 5 shows that once the optimal adjustment has been achieved, there is also an oscillation of
the current that can produce acoustic noise and mechanical vibration. By raising the value of
Pr18 to 3, the situation is much improved (fig. 6).
Page 88 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
If the mechanical parts easily tend to oscillate, very low Pr16 values are recommended. In this
configuration, Hi-drive typically dampens the torque request of the motor in order to avoid
triggering mechanical oscillations. This configuration is shown in figure 7.
Page 89 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
ADJUSTMENT WITHOUT INSTRUMENTATION
If you do not have an oscilloscope, you must:
-
Determine the value of Pr16 as described above.
Determine parameter Pr17 using the following formula:
Pr 17 = 1488 ⋅
153.41⋅ Pr 16 ⋅ J tot
Nm peak
where: J tot is the total inertia (motor + load) expressed in kgm2.
Nm peak is the available torque with the converter peak current.
-
Enable the converter and use the external control to move the axis. Move Pr17 to find the
value where the axis seems to move best.
- Estimate the value of Pr18 using the following formula:
Pr 18 = 0.68 ⋅
Pr 17
⋅2
Pr 16
If the result is less than 1, Pr18 must be set to 1.
If the adjustment is not satisfactory, repeat the procedure with lower values of Pr16.
Page 90 of 233
Parker Hannifin S.p.A Divisione S.B.C
9
Hi-drive User Manual
ANALOG AND DIGITAL I/Os
9.1 Digital I/Os
In terminal block X5 there are 5 digital inputs, combined with binary parameters b90.0 $ b90.4.
The following table shows the details of each digital input reference:
Digital input Binary parameter
IN 0
b90.0
IN 1
b90.1
IN 2
b90.2
IN 3
b90.3
IN 4
b90.4
pin Terminal
28
27
X5
26
25
5
In the same X5 terminal block, there are 2 digital outputs combined with binary parameters:
Digital output Binary parameter pin Terminal
OUT 0
b91.0
22
X5
OUT 1
b91.1
21
Output voltage depends on the voltage supplying digital outputs (terminals 20 and 23), than can
range between 5 and 24 Vdc.
9.2 Relay outputs
The status of the relay output is managed by the binary parameter b91.2, with an output voltage
of 24Vdc.
Relay output Binary parameter pin Terminal
N.O.
18
b91.2
X5
N.C.
19
9.3 Analog outputs
Two programmable analogue outputs are available: “monitor 1” (pin 8 of X5) and “monitor 2”
(pin 7 of X5), that can be set to monitor parameters. The output voltage is ±10 Vdc (see section
on “programmable analogue outputs”).
Page 91 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
10 DYNAMIC BRAKING
In its basic configuration, a dynamic braking resistor is available inside; the resistor data are
provided in the default drive configuration.
If an external dynamic braking resistor is required, enter the relevant data in the currently used
resistor.
Attention: we remind you that the external braking resistor value in ohm is not freely selectable,
but must be based on the type of drive used. Refer to the “Technical features” table.
Par.
Pr274
Pr275
Description
Braking resistance. Resistance in ohm,
depending on the features of the resistor installed
in the drive.
Braking resistor management. Resistor power
in Watt, depending on the drive size.
Field
W
Range
0÷65535
[Ω]
Def.
-
Res.
1Ω
W
0÷65535
[W]
-
1W
N.B. When you carry out a default procedure, all factory parameters are changed and any
previously entered value is lost.
Page 92 of 233
Parker Hannifin S.p.A Divisione S.B.C
Hi-drive User Manual
11 KEY PARAMETERS
The torque, speed, acceleration and position control functions are carried out by special digital
electronics. In this section we explain how parameters are set and the meaning of each
parameter. We also provide a functional block diagram and a description of advanced functions.
The system is easy to use and flexible.
The diagram below is a general block diagram of the part of the converter that is controlled by
parameters.
analogue
digital
REFERENCE
internal
MANAGEMENT
b40.2
LIMIT
&
SPEED
CONTROLLER
STOP
TORQUE
REQUEST
OPERATING
TORQUE
LIMIT
MANAGMENT
MODE
SPEED
ALARM
WINDOWS
MANAGEMENT
Pr181
TORQUE
CONTROL
ELECTRIC
SHAFT AND
POSITION
ELECTRONIC
CAMS
Page 93 of 233
CAN
IN
REAL TIME
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Left limit
40.4
Analogue reference offset
Reference offset
40.5
Stop
40.6
Pr7
Pr2
A/D
b40.0
b40.12
Pr3
2 anal. ref. Full scale
Frequency reference
nd
Frequency
input
A/D
Analogue
reference
input
(X5 – 13-14)
Accel and decel
ramp
1°fondoscala rif. anal.
Pr4
Pr8
Reference hold
b40.2
acc
40.3
Pr54
A/D
Stop
control
Pr9
Band limiter
Integer gain
dec
Pr18
dampening
Pr16
Pr11
b39.2
Peak current
Stop ramp
Pr6
ω
Reserved reference
I2t active
Motor
Pr33
Nominal current
Speed window
b40.7
b40.8
max
No
torque
Pr55
Analogue auxiliary input
Motor speed
High speed limit
Pr14
Alarm
management
Pr23
“0”
overvoltage
41.2
Drive ok
undervoltage
Zero speed
41.3
forward
41.4
overcurrent
In speed
41.1
Pr15
Pr174
Torque limit
Pr0
Over
speed
41.0
Pr35
Torque monitor
41.11
Motor speed
Pr12
Current
limit
Pr19
Pr0
0
Overspeed limit
Pr13
Main analogue input
Pr17
Pr10
b40.13
Pr5
Internal reference
MAIN BLOCK
Pr1
Main reference
Pr1
Analog input
(X5 – 13-14)
Right limit
External alarm
Speed loop FBK error
Converter
overtemperature
41.7
41.8
Loww speed limit
Default
parameter
Auxiliary alarm
Check Sum PLC
“0”
Drive enable
41.5
Hardware enable
Software enable
40.9
Check Sum parameter
Undervoltage 24V
Mbient overtemperature
Braking resistance protection
Speed FBK initializing error
Position FBK initializing error
Position loop FBK error
PTC alarm active
Page 94 of 233
Pr76
Encoder phasing
result
41.6
Phasing ok
41.12
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
The parameters can be grouped according to their functions as follows.
IMPORTANT
from Pr0 to Pr49
from Pr130 to Pr174
from Pr90 to Pr129
from Pr181 to Pr250
from In0 to In255
main parameters
position loop
Pico-PLC parameters
operating mode parameters
Pico-PLC instructions
The units and main resolutions of parameters are as follows:
PARAMETER TYPE
speed
acceleration ramp
position
current
UNIT
revolutions/minute
seconds/1000 revolutions/minute.
pulses per motor revolution
% of the converter peak current
RESOLUTION
1
0.001
1
0.1
The main block diagram shows the speed loop. Symbols used stand for functions as described
below.
Binary parameters are represented as switches and their position in the diagram corresponds to
the default value.
Page 95 of 233
Parker Hannifin S.p.A S.B.C. Division
A
• Read/write of parameter PrX
A = value of parameter PrX
• Read/write of parameter PrX
B = value depending on the values of A and PrX
• Read-only parameter
PrX indicates the value of A which can also be binary
• Read/write of a binary parameter
The switch position indicates bx.y=0
A
Pr X
B
Pr X
A
Pr X
bx.y
• The value of the binary parameter bx.y positions the switch.
bx.y
A
Hi-drive User Manual
• If A is less than B, C =1 (true). Otherwise, C = 0 (false).
B
C
A
B
C
D
E
F
A
• The value of G is the lowest value of A B C D E F.
G
A
B
C
A
B
C
+
C
• Only if A = 1, B = 1 and C = 1. Otherwise, C = 0.
• If A or B is equal to 1, C = 1. Otherwise, C = 0.
• C = A – B.
B
• values coming from the hardware
• values sent to the hardware
A
B
A
• The value of A is converted into B. For instance, if the
triangular symbol shows A/D, the analogue value of A
is converted into the digital value B
• The maximum value of A will be PrX.
Pr X
Page 96 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
11.1 Key parameters
IMPORTANT
IMPORTANT
IMPORTANT
ƒ
ƒ
ƒ
Any time you need to save parameters and PLC settings, disable the drive
first.
Any time you need to change the drive configuration parameters, switch
off and on again the converter in order for the new settings to be effective.
All decimal and binary parameters that are not declared are RESERVED
and must not be used.
Decimal parameters
Description
Field
Par.
Motor speed: this is a read-only parameter
R
Pr0
indicating the motor speed.
Analogue reference offset. Expressed as a count
W
Pr1
of the input converter. The setting limits are 15000 and +15000.
First full scale of analogue reference: If b40.0=0
W
Pr2
and b40.12=0, the value of Pr7 will be equal to:
Vin × Pr2
where Vin is the voltage at the
9,76
analogue input.
Second
full scale of the analogue reference: If
W
Pr3
b40.0=1 and b40.12=0, the value of Pr7 will be
equal to:
Vin × Pr3
where Vin is the voltage at the
9,76
analogue input.
Full scale of frequency reference: If b40.12=1
W
Pr4
and b40.13=1, the value of Pr7 will be as follows:
if b42.5=0,
Fin • Pr 4 • 2
(frequency/sign signals)
Pr 7 =
2.000.000
if b42.5=1
Fin • Pr 4 • 2
(quadrature signals)
Pr 7 =
500.000
where Fin is the frequency at the encoder input
(≤400 kHz).
Digital reference. If b40.12=1, and b40.13=0,
W
Pr5
then Pr7 = Pr5.
R
Internal reference. It is reserved to operating
Pr6
modes. If b40.2=1, the parameter is used as a
reference for the speed controller: the active
operating mode will write its speed request in
parameter Pr6.
R
Speed reference monitor. If b40.2=0 is used, Pr7
Pr7
is the reference for the speed controller. In some
operating modes, Pr7 can be used as a reference
for other values (torque/acceleration) and in these
cases Pr7 will be expressed in the most suitable
unit.
Page 97 of 233
Range
± 15.000
[rpm]
± 15.000
[rpm]
Def. Res.
0 1 rpm
±15200
[rpm]
3000 1 rpm
±15200
[rpm]
-3000 1 rpm
-32768÷
+32767
3000 1
0
1 rpm
± 14.000
[rpm]
[rpm]
0
1 rpm
0
1 rpm
[rpm]
0
1 rpm
Parker Hannifin S.p.A S.B.C. Division
Par.
Pr8
Pr9
Pr10
Pr11
Pr12
Pr13
Pr14
Pr15
Pr16
Pr17
Pr18
Pr19
Hi-drive User Manual
Description
Field
W
Acceleration ramp for positive speed. The
positive speed acceleration required by the motor
via the speed reference is internally limited so that
it takes Pr8 seconds to achieve an acceleration of
1000 rpm.
W
Deceleration ramp for positive speed. The
positive speed deceleration required by the motor
via the speed reference is internally limited so that
it takes Pr9 seconds to achieve an acceleration of
1000 rpm.
W
Acceleration ramp for negative speed. The
negative speed acceleration required by the motor
via the speed reference is internally limited so that
it takes Pr10 seconds to achieve an acceleration of
1000 rpm.
W
Deceleration ramp for negative speed. The
negative speed deceleration required by the motor
via the speed reference is internally limited so that
it takes Pr11 seconds to achieve an acceleration of
1000 rpm.
W
Emergency ramp. The deceleration required by
the motor limit switch and stop functions is
internally limited so that it takes Pr12 seconds to
achieve an acceleration of 1000 rpm.
Overspeed limit. If the motor speed absolute W
value exceeds the value set in Pr13, b41.0 will be
=1, otherwise, it will be = 0.
High speed limit. When b40.7=0, if the speed
W
difference between motor and reference is lower
than Pr14 and greater than Pr15, b41.1 will be =1
(otherwise, it will be = 0). When b40.7=1, if the
motor speed is lower than Pr14 and greater than
Pr15, b41.1 will be =1, otherwise, it will be = 0.
Low speed limit. When b40.7=0, if the speed
W
difference between motor and reference is less
than Pr14 and greater than Pr15, b41.1 will be = 1,
otherwise, it will be = 0. When b40.7=1, if the
motor speed is less than Pr14 and greater than
Pr15, b41.1 will be =1, otherwise, it will be = 0.
W
Integral gain of the speed controller.
Proportional gain of the speed controller: If
Pr16=0, Pr17 is the proportional gain of the speed
controller.
Mechanical torque filter. Pr18 is used to set the
time constant of a first order filter placed on the
torque request digital signal. The frequency of the
filter cut will be: 620/Pr18 Hertz.
Peak current. This is the maximum current that
the converter can supply to the motor. It is
expressed as a percentage of the peak current of
the converter. In general, it should never exceed
three times the motor rated current.
Page 98 of 233
W
Range
0.002÷
65.535
[s/krpm]
Def. Res.
2 0.001 s
0.002÷
65.535
[s/krpm]
2
0.001 s
0.002÷
65.535
[s/krpm]
2
0.001 s
0.002÷
65.535
[s/krpm]
2
0.001 s
0.002÷
65.535
[s/krpm]
2
0.001 s
±15000
[rpm]
3500 1 rpm
±15000
[rpm]
20
1 rpm
±15000
[rpm]
-20
1 rpm
0÷
+32.767
0÷
+32.767
120
1
2000
1
3
1
W
1÷
+32.767
[1=64μs]
W
0%÷100% 1000
[A]
0.1%
Ipeak
Parker Hannifin S.p.A S.B.C. Division
Par.
Pr20
Pr21
Pr23
Pr25
Pr28
Pr29
Pr30
Pr31
Pr32
Pr33
Pr35
Pr36
P37
Hi-drive User Manual
Description
Field
DC Bus Voltage Unit =volt, read-only parameter.
R
Displays the DC bus voltage value.
W
Nominal_DC_BUS. When the drive is supplied in
continuous voltage, the power supply voltage
value must be written in this parameter.
R
Alarm code: This is the code for a present alarm.
Code 0 represents the absence of alarms. See the
table of alarm codes for more details (see
Appendix “Alarms”).
Software version code. A read-only parameter
R
indicating the software version installed.
Motor shaft position. Read-only parameter
R
indicating the absolute position of the resolver.
Number of motor poles. Indicates the number of
W
motor poles.
W
Offset on the feedback position. Pr30 is used to
correct electronically the mechanical position of
speed feedback. Indicates the current vector
position displacement and a mechanical revolution
(corresponding to 65536).
W
To select the type of motor connected to the
drive. 0: rotary brushless motor, 1: 4-pole
asynchronous motor in sensor vector control
mode.
W
Rated speed. This is the motor rated speed. The
speed that has been set is used to limit the speed
request. Therefore, it should be set to about 10%
greater than the maximum operational speed.
Rated motor current. The motor rated speed
W
must be set.
Torque monitor. Indicates the torque (or current)
R
percentage supplied by the motor.
R
Winding thermal image. This is a read-only
parameter indicating the estimated heat in the
motor innermost coils of the motor windings. If
this reaches the value of 100.0 % equal to the
nominal value, b41.11 will become 1 and
therefore the current will be limited to the nominal
value.
Functional description: supposing to supply the
drive peak current, starting from an initial
condition where the current output was zero, after
2s parameter Pr36=100% and b41.11=1. As a
result: the current supplied by the drive will be
limited to the nominal value. This condition will
stay permanently. However, if the drive is set to
supply zero current, after about 35s, parameter
Pr36 will return to a zero value.
R
Braking Energy. During the braking phase the
value of parameter Pr37 increases, but this value
must decrease, until to 0, when the drive is out of
the braking phase. If the value exceeds 120.0%,
the drive shows error 14.
Page 99 of 233
Range
-
Def.
0
Res.
1V
0÷744
[V]
560
1V
-
1
-
-
-
1 step
0
1
-32768 ÷
+32.767
0
1
0÷1
0
1
0÷14.000
[rpm]
0
1 rpm
0.1÷In
-
0.1 A
0÷1000
% Ipeak
0÷1000
% Tn
0
0.1%
Ipeak
0,1%
Tn
0÷4095
[step]
0÷64
0÷1200
0
0
0,1%
Parker Hannifin S.p.A S.B.C. Division
Par.
Pr45
Pr46
Pr47
Pr48
Pr49
Pr50
Pr51
Pr52
Pr53
Pr54
Pr55
Pr56
Pr57
Pr58
Pr59
Hi-drive User Manual
Description
Field
Base_speed_asinc. Asynchronous motor speed in
W
synchronism conditions.
W
Motor resistance. Unit ohm. The phase-phase
resistance of the motor. The entered value is
expressed in tenths of ohm.
W
Motor inductance. Unit mH. The phase-phase
inductance of the motor. The entered value is
expressed in tenths of mH.
SLIP_ASINC. Asynchronous motor slip.
W
MAGN_CURR_ASINC. Asynchronous motor
magnetizing current.
Pr 49 = Pr33 × 1 - cos 2ϕ
Analogue pointer 1. Used as parameter pointer.
The set value corresponds to the Parameter
number. Pr50= value of pointed Pr.
Analogue output 1 scale. Defines the scaling of
the monitored parameter: 2Pr[51] .
Analogue pointer 2. Used as parameter pointer.
The set value corresponds to the Parameter
number. Pr52= value of pointed Pr.
Analogue output 2 scale. Defines the scaling of
the monitored parameter: 2Pr[53].
Analogue input 1. Values can range from –32768
to +32767 with input voltages ranging from –10V
to +10V [1V~3276,7 count].
Analogue input 2. Values can range from –1023
to +1023 with input voltages ranging from –10V
to +10V [1V~102,4 count].
Module temperature. Measures the power
module temperature in °C. (0) when temperature
is within the operating condition range (based on
the drive size).
Board temperature. Measures the temperature of
the control board in °C and generates an alarm
when the temperature gets over 70°C (158°F).
No. of FBK. Encoder pulses. Indicates the
number of pulses per revolution (times 4 in the
count) ranging from 1 to 32767. It can be set <0 to
reverse the count only with incremental encoders
and not with SinCos encoders, as the latter require
a correct cabling of sine-cosine signals (traces A
and B). With values above 32767, the number of
pulses per revolution must be set as powers of 2
up to the limit of 2(±)18 pulses per revolution (then
times 4 by the front read) [see mode set by bits 1
and 2 of parameter 65].
The sign “±“ indicates the direction of rotation:
negative or positive feedback.
No. of IN. Encoder pulses Like Parameter 58 but
exclusively dedicated to incremental encoders.
Page 100 of 233
W
Range
[rpm]
Def.
Res.
1 rpm
0.1÷300
[Ω]
0
0.1 Ω
0.1÷500
[mH]
0
0.1mH
0÷32767
[rpm]
0÷32767
[A]
0
1 rpm
0
0.1 A
0
1
W
0÷385
W
±16
W
0÷385
35
1
W
±16
0
1
W
-
0.1
-
0.1
R
-32768
÷ 32767
count
-1024
÷ +1023
count
[°C]
-
1°C
R
[°C]
-
1°C
W
0
1
W
-32768 1024
÷ +32767
1
W
-32768 1024
÷ +32767
1
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Description
Field
W
Number of resolver poles. The pole number
setting has the following values: 2, 4 or 8; where
the limit speed is 14000rpm for 2 poles, 7000rpm
for 4 poles and 3500rpm for 8 poles.
N.B. when the resolver is not used, leave
parameter Pr60=2.
W
Input B selection
Pr62
0 Sincos + EnDat
1 Sincos
2 Less wiring
3 Square incremental encoder
4 F/D incremental encoder
5 square IN2 IN3 (24V) inputs
6 IN2 IN3 (24V) F/D inputs.
7 Sincos + Hiperface
(The setting is enabled at the next power on ).
W
Input C selection
Pr63
3 Square incremental encoder
4 F/D incremental encoder
5 square IN2 IN3 (24V) inputs
6 IN2 IN3 (24V) F/D inputs
(The setting is enabled at the next power on ).
W
Pr69:68 Multiturn zeroing preset. In this register the
machine resetting value is entered. The value can
be different from zero.
W
Enc. simulation parameter pointer Read always
Pr71
in Long at 32 bit; the selected parameter is the low
word. If you select a single word, mind the
significance of the following high word, which is
also read. E.g. if we read Pr0 and the motor is
halted, but the speed has a value of +/-1 Rpm, the
pointer will read +1 and write +1, at –1 it reads the
long Pr0:Pr1 word, and therefore 65535; the
encoder simulator will in this case be moved by
the same value.
Enc. Simulation pulses per revolution. If
Pr72
b70.0=0, values range from 4 to 65535 pulses per
revolution; if b70.0=1 is the exponent and the
maximum value that can be entered is 18,
Default=1024 is the number of pulses per
revolution used in the encoder simulation. The
maximum frequency is 400 kHz.
W
Par.
Pr60
{pulse encoder}× {speed [rpm]} ≤ 400 [kHz ]
Fin =
60 [sec/ min ]
Pr76
Pr77
Pr167
If b70.0=0, the range is from 0 to 65535
pulses/turn.
If b70.0=1, the value of parameter is the exponent,
and the max value is 18.
Enc. phasing result. When the encoder phasing is
completed, this parameter indicates if the phasing
is OK or if it must be repeated taking into account
the previously disregarded conditions.
Enc. address CAN IN.
Drive type code.
Page 101 of 233
Range
2, 4 or 8
Def.
2
Res.
1
0÷7
0
1
2÷6
3
1
-32768
÷ +32767
0
1
0÷385
0
1
1024
1
0
1
0÷
+32767
0 ÷ 18
R
W
R
0÷1
0
Parker Hannifin S.p.A S.B.C. Division
Par.
Pr174
Pr181
Pr256
Pr258
Pr259
Pr260
Pr261
Pr268
Pr271
Pr274
Pr275
Hi-drive User Manual
Description
Field
Torque limit. Is used by the operating modes to
R
limit the torque to the motor.
W
Operating mode. Parameter Pr181 can be used to
select the active operating mode. The value 0
means that no operating mode has been selected.
W
Serial link 232 speed code. Code used to program
the transmission speed. For further information,
see the section on the SERIAL INTERFACE.
W
Serial link 422 speed code. Code used to program
the transmission speed. For further information,
see the section on the SERIAL INTERFACE.
Serial link 422 address code. For further
W
information see the relevant section..
BAUDRATE CAN. CAN line transmission speed
W
programming code.
CAN address. Indicates CAN address value.
W
FPGA_SW_REL. Indicates the firmware version
R
in the FPGA flash memory.
W
Encoder vibration step. Indicates the phasing
vibration duration length. Parameter calculated
with type 2 phasing (see relevant section for
information about type 2 phasing procedure).
W
Braking resistance. Resistance in ohm,
depending on the features of the resistor installed
in the drive.
Braking resistor power. Resistor power wattage,
W
depending on the drive size.
Range
Def.
0%÷100% 1000
[A]
0÷385
0
0÷8
6
1
0÷31
6
1
0÷31
0
1
0÷32767
1
1
0÷127
-
1
-
1
-
0÷ 200
-
1
0÷65535
-
1Ω
0÷65535
-
1W
Binary parameters
Description
Par.
b39.0 DC supplied drive Dcbus nominal in Pr21. The value identifies the drive’s
power supply: in case of three-phase alternated supply, the bit must be set to
0; in case of continuous supply , the bit must be set to1.
b39.2 Torque required by the main analogue reference. If the bit is set to 1,
10Vpeak will be taken as reference.
b39.5 Brake alarm function. If b39.5=0 the brake alarm function is enabled (error
14), otherwise the function is disabled if b39.5=1.
b39.6 IEC 61131 automatic memory extension. (1) the pico-PLC is disabled
b39.13=0), the all instructions of the pico-PLC (512 byte) are used as
(✎)
automatic variables for the IEC 61131 programming language.
b39.8 Automatic undervoltage reset. If set to 1, the under-voltage alarm will
automatically be set to 0 when power returns. (The setting is enabled at the
next power on ).
b39.10 Motor cogging compensation. If bit = 1, motor cogging compensation is
enabled. This command must not be given before calculating the
compensation (b42.7).
b39.11 Motor control PWM 16 kHz – (0) 8 kHz. If enabled, b39.11=1, the first
time the drive is powered on again PWM at 16Khz is enabled, the drive
nominal and peak currents are derated by 30%. (Pr33 – 30% and Pr19 –
30%). (The setting is enabled at the next power on ).
b39.12 Enable IEC 61131. (1) Start. (0) Stop
Page 102 of 233
Res.
0.1%
Ipeak
1
Field
W
Def.
0
W
0
W
0
W
0
W
0
W
0
W
0
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Description
Par.
Pico-PLC
status:
START(1)
–
STOP(0). If set to 1, the PLC program is
b39.13
executed. If set to 0, the Pico-PLC is in stop and the PLC instructions can be
modified.
b39.14 (0) IN1 value captured on the rising edge - (1) IN1 value captured on the
falling edge. The IN1 signal switching front depending on the bit setting.
b39.15 (0) IN2 value captured on the rising edge - (1) IN2 value captured on the
falling edge. The IN2 signal switching front depending on the bit setting.
b40.0 Selection of the first or second full scale of the speed reference. If = 0,
Pr2 will be used to rate the analogue reference. If = 1, parameter Pr3 will be
used.
b40.1 Algorithm to suppress vibration at 0 speed. If = 1, the algorithm is
enabled.
b40.2 Speed reference or operating mode selection. If = 1, the reserved
reference of the operating mode in use is used. If = 0, the reference selected
by b40.0, b40.12 and b40.13 is used.
b40.3 Reference hold. If = 1, the reference will not be updated and the motor will
not follow the variations of the input reference. If = 0, the reference will
follow the variation of the input reference.
b40.4 Left limit switch. If = 1 and the reference selected requires positive speed,
the reference is set to 0 following the ramp set in Pr12. If = 0, no control is
made.
b40.5 Right limit switch. If = 1 and the reference selected requires negative
speed, the reference is set to 0 following the ramp set in Pr12. If = 0, no
control is made
b40.6 Motor stop function. If = 1, the motor is set to zero speed following the
ramp set in Pr12.
b40.7 Absolute/relative speed window selection. If = 0, the speed window Pr14
Pr15 b41.1 will function in absolute mode. Otherwise, if = 1, it will function
in relative mode.
b40.8 Analogue torque limit. If = 1, Pr55 will be used, followed by the auxiliary
analogue input, in order to limit the torque to the motor. Consider that in this
mode the sign of the voltage applied to the differential analogue input is not
relevant.
b40.9 Software enable. If = 0, the converter cannot be enabled.
b40.10 Low voltage. Activates low voltage management.
b40.11 Injection of third harmonic in modulation.
b40.12 Digital/analogue reference selection. If = 0, the analogue input will be
selected as the main reference. If = 1, the reference will be digital and
b40.13 can be used to select parameter Pr4 or parameter Pr5.
b40.13 Internal frequency reference selector. If b40.12 = 1, b40.13 can be used to
make the selection. If = 0, the internal reference can be used. If = 1, the
frequency input (encoder-in) which can be configured as
frequency/direction.
b41.0 Overspeed. In absolute mode, when the value of the motor speed (Pr0)
exceeds the value set in Pr13, b41.0 = 1. Otherwise, b41.0 = 0. In relative
mode, the overspeed is between motor speed and internal reference
respected the Pr13.
b41.1 “In speed”. When b40.7=0, if the motor speed is lower than Pr14 and
greater than Pr15, b41.1 will be =1, otherwise, it will be = 0. When b40.7=1,
if the speed difference between motor and reference is lower than Pr14 and
greater than Pr15, b41.1 will be =1, otherwise, it will be = 0.
b41.2 Zero speed. In absolute mode, if the motor speed Pr0 = 0, b41.2=1.
Otherwise, b41.2 = 0. In relative mode, is the difference between the motor
speed and the reference: when these are equal, then b41.2=1.
Page 103 of 233
Field
W
Def.
1
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
W
W
W
1
0
0
0
W
0
R
0
R
0
R
0
Parker Hannifin S.p.A S.B.C. Division
Par.
b41.3
b41.4
b41.5
b41.6
b41.7
b41.8
b41.10
b41.11
b41.12
b41.13
b41.14
b42.0
b42.1
b42.2
b42.3
b42.4
b42.7
b42.8
b42.10
b42.12
b42.13
b42.14
b42.15
b64.0
b64.2
b64.4
Hi-drive User Manual
Description
Forward. In absolute mode, if the motor speed Pr0 is > 0, b41.3=1.
Otherwise, b41. 3 = 0. In relative mode, b41.3=1 if the difference between
the motor speed and the reference is > 0.
Converter O.K. If = 1, there is no alarm. Otherwise, = 0.
Hardware enable. If =1, the converter hardware is enabled.
Phasing O.K. If =1, phasing has been completed successfully.
External alarm. An alarm that can be used by the user.
Auxiliary alarm. A second alarm that can be used by the user.
Speed controller saturation. b41.10=1 when the speed controller is
supplying the maximum current.
I2T active. Indicates that Pr36 has reached the 100.0 % value and therefore
the converter is limiting the current to the nominal value.
Converter enabled.
480V mode. If b41.13=1, the 3-phase power supply voltage is at 440V (400
+ 10%). If b41.13 = 1 at power up, the nominal current Pr33 and peak
current Pr19 of the drive are derated by10% (Pr33-10% and Pr19-10%).
Brake alarm. This bit indicates when the parameter Pr37 exceeds the 100%
(b41.14=1). This bit can be used in pico-PLC to communicate the alarm.
Ref. offset reset command. Analogue (if < 200mV) (auto reset). Command
b42.0 automatically compensates for the main analogue reference offset
entering the reference reset value in Pr1. Such operation is only performed if
the offset to be compensated is lower than 200mV.
Key parameters blocked(0) – modifiable(1). If set to 0, key parameters
cannot be modified. If the bit is set to 1, the drive requires the default
parameters again (if Pr23=0).
PTC motor pre-alarm (1). This pre-alarm allows to stop the machine
before (around 125°C – 257°F) reaching the alarm limit (around 135°C –
275°F).
<150VAC power supply. It is 1 if the power line is < 150VAC.
3-phase power supply. It is 1 if the power line is not 3-phase.
Cogging compensation calculation command. (1) Calculates the motor
cogging mapping. When the calculation has been completed, the bit status
automatically goes back to“0” (see par. “motor cogging compensation”).
Static brake release. (1) Controls the output controlling the emergency
brake of terminal block X3.
The brake block-release function in all operating conditions must be
performed by the user.
Alarm reset command. After removing the cause that has generated the
alarm, give a command to reset the drive alarm status.
Programming default. Programming default loading command.
Operating mode default. Operating mode programming default loading
command.
Save Pico-PLC. This command is used to save PLC instructions. Never
activate while drive is enabled.
Save parameters + tables. This command is used to save parameters. Never
activate while drive is enabled.
Sensing function. When (1) is active, it means that a FBK sign is present
and that the power supply of the FBK encoder, ranging from 5 to 8V, is
compensated for any voltage drops due to the cable length.
Type 1 encoder phasing (vector orientation). See specific section.
Type 2 encoder phasing (vibration). See specific section.
Page 104 of 233
Field
R
Def.
0
R
R
R
W
W
R
0
0
1
0
0
1
R
0
R
R
0
0
W
0
W
0
W
0
R
0
Rw
Rw
Rw
0
0
0
W
0
W
0
W
W
0
0
W
W
R
-
W
w
0
0
Parker Hannifin S.p.A S.B.C. Division
Par.
b64.8
b64.9
b65.0
b65.1
b65.2
b65.3
b65.6
b65.7
b65.8
b65.9
b65.10
b65.11
b65.12
b65.13
b65.14
b65.15
b70.0
b70.3
b70.4
b70.5
b78.0
b78.7
Hi-drive User Manual
Description
Phase value saving. The command saves the phase value on the encoder
EnDat (disables the drive and prevents any further enabling command. To
enable the drive you’ll need to switch it off and on again).
Multiturn position reset on encoder EnDat. Defines the machine “zero”
position. The value is set in register Pr68:69. The command must be given
while the drive is disabled. In order for this function to be available, save the
parameters and switch the drive off and on again (disables the drive and
prevents any further enabling command. To enable the drive you’ll need to
switch it off and on again).
FBK power supply. (1) if fbk encoder power supply is active.
FBK B encoder pulses per revolution count selection. (1) number of
pulses per revolution of FBK B encoder =2Pr58 , (0) number pulses per rev.=
Pr58.
FBK C encoder pulses per revolution count selection. (1) number of
pulses per revolution of FBK B encoder =2Pr59 , (0) number pulses per rev.=
Pr59.
Encoder zero point dog fine tuning. When the bit is set to1, it activates a
function that enables the zero encoder point dog fine tuning following
phasing only for less wiring.
Encoder input voltage selection (*), only for FBK B.
See table below.
Encoder input voltage selection (*), only for FBK B.
See table below.
Digital filter per enc. FBK (X7) See feedback chapter.
Digital filter per enc. FBK (X7) See feedback chapter.
Digital filter per enc. FBK (X7) See feedback chapter.
Digital filter per aux. enc. FBK (X9) See feedback chapter.
Digital filter per aux. enc. FBK (X9) See feedback chapter.
Digital filter per aux. enc. FBK (X9) See feedback chapter.
Speed loop feedback selection bit (**). See table below.
Speed loop feedback selection bit (**). See table below.
Selection of number of pulses per revolution for Encoder OUT. (1)
number of Pulses pr rev. of encoder OUT = 2Pr72 (0) number of pulses per
rev.= Pr72. If the parameter is set to 0, the value entered in parameter Pr72
is the value of encoder pulses. If is set to 1, the value of encoder pulses will
be calculated as 2 elevated to the nth power, where the exponent will be the
value entered in parameter Pr72, up to a maximum value of 218 .
Parameter simulation. When the bit is set to 1, the encoder output
simulation does not have the motor shaft position as a reference, but rather
the value of the parameter pointed by Pr71, so that increments can be
simulated starting from a path generator rather than from the real motor
position.
Enable save in retentive memory. (1) enable the save command of the
value indicate in the pointer parameters from Pr310 to Pr350 in to the
retentive variables.
Status of background routine. This bit is to set to zero when the
background routine finish in which the retentive variables are written in the
NOVRAM: set b70.5=1, this bit returns to 0 when the routine of save finish.
Disables emc transmission in CANopen. The function is active when the
bit is 1.
Enables out generation of a reference position on the digital bus. The
function is active when the bit is 1.
Page 105 of 233
Field
W
Def.
0
W
0
R
W
0
W
0
W
0
W
0
W
0
W
W
W
W
W
W
W
W
R
0
0
0
0
0
0
0
0
0
W
0
W
0
W
0
W
0
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Description
CAN bus, warning. The status is active when the bit is 1. The parameter
warns when the bus communication is not working.
b79.1 CAN bus, off warning. The status is active when the bit is 1. The parameter
warns when the communication bus is off.
b79.3 Rs232 serial initializing command. Command to reinitialize serial
communication whenever the speed value of the serial link (Pr256) has been
modified. The serial link is in any case initialized when the converter is
powered on.
b79.4 Rs485/422 serial initializing command. Command to reinitialize serial
communication whenever the speed or the address value (Pr258 and Pr259)
of the serial link have been changed. The serial link is in any case initialized
when the converter is powered on.
b79.5 CAN A initializing command. Command to reinitialize CAN
communication whenever the speed or the address value (Pr260 and Pr261)
of the CAN line have been changed. This is in any case initialized when the
converter is powered on.
b79.6 Reference position initializing command on digital bus CAN B.
b79.12 Sending spare data in CANopen Emergency. Enables sending datacontaining messages. The function is active when the bit is 1.
b79.14 CAN bus block sync watchdog.
b79.15 Position reference CAN bus watchdog on digital bus.
Par.
b79.0
Page 106 of 233
Field
R
Def.
0
R
0
W
0
W
0
W
0
W
W
0
0
RW
R
0
0
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
12 OPERATING MODES
Parameter Pr181 (default = 0) is used to select the operating mode. Every operating mode
controls speed using parameter Pr6 and can use parameter Pr174 to limit the torque at the motor
through parameter Pr21 (see the block diagram). Speed control will use as reference Pr6 or Pr7,
depending on the value of b40.2. Before changing Pr181, b40.2 must be set to 0 in order to avoid
unwanted movements of the motor. Therefore, it is possible to set Pr181 to the value that
corresponds to the selected operating mode. The parameter b42.13 is used to load the default
parameters for the selected operating mode.
12.1 Position control
All operating modes need to control the motor in position by using the position loop described in
the block diagram shown in the figure below.
Servo window 1
Pr141:140
Servo error 1
b170.4
Servo window 2
Pr143:142
Servo error 2
b170.5
FFWD
Position
scaling
abs()
Position
reference
Pr147:146
Pr131:130
Pr149
FFWD position filter
Position error
Pr137:136
Pr145
Proportional gain of
position controller
Pr144
Pr6
Speed reference
reserved
Maximum speed
Pr133:132
Position loop resolution
Pr169
From feedback
Motor position
Pr135:134
Absolute position
in mech. revolution
Reset 1
b170.1
Pr131:130=Pr133:132=0
Pr28
Motor shaft
position
Reset 2
b170.2
Pr131:130=Pr133:132
Page 107 of 233
Reset 3
b170.3
Pr131:130=Pr133:132=Pr135:134
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Operating modes generate the position reference, which is processed through position control in
order to generate a speed request that will be transmitted to the speed loop through parameter
Pr6, whose maximum value, with any sign, is limited by parameter Pr144.
The position control function calculates the “position error” value and compares it to the error
window in order to generate a “servo error” warning message. An adequate response to the
servo error message will be given by the user through pico-PLC.
Parameter Pr145 identifies the value of the proportional gain in the position loop and shall be
adjusted in such a way as to ensure a vibrationless movement with no overshoot on the final
position. As the gain is only proportional, the error will tend to increase as the axis speed
increases, and then it will be recovered at the end of the positioning process. For this reason, if it
were necessary to act more quickly, e.g. in a quick positioning, while minimizing the profile
execution error rate, you could enter feedforward Pr147:146 and add a filter on the same
feedforward by parameter Pr149.
The position loop resolution can be selected through parameter Pr169, that would be considered
as the exponent of 2 elevated to the nth power: 2Pr169.
Decimal parameters
Field Range Def.
Description
Par.
±231
Pr131:130 Reference position. Indicates the motor “theoretical” R
position. The parameter resolution is defined according
to the setting of parameter Pr169.
±231
Pr133:132 Motor position. Indicates the “real” position. The R
feedback resolution can be set in parameter Pr169, with
values ranging from 212 and 220.
±231
Pr135:134 Absolute position in the mechanical revolution. The R
counter resolution can be selected by parameter Pr169.
±231
0
Pr137:136 Position error. Register containing the difference R
value between the motor position and the reference
position.
±231 100
Pr141:140 servo1. If the position error as an absolute value W
exceeds the value set in Pr140, b70.4 is set to 1.
Otherwise, b 170.4 = 0.
±231 200
Pr143:142 servo2. If the position error as an absolute value W
exceeds the value set in Pr142, b70.5 is set to 1.
Otherwise, b 170.5 = 0.
Speed
limit in position. By this parameter the motor W
0 3200
Pr144
maximum speed can be limited in the position loop.
÷14000
This parameter is not considered if the set value is
[rpm]
greater than the value of Pr32.
W
Proportional position gain.
100
0
Pr145
÷32000
W
±231 7324
Pr147:146 Position feedforward scaling.
Pr149
Position feedforward FIL. Delay filter on the speed W -32768 0
÷32767
feedforward in the position loop. Pr149 is used to set
the time constant τ of a first order filter placed on the
speed request digital signal. (τ = Pr149 * loop field
time).
Position loop resolution selection. The position loop W 12÷20 12
Pr169
resolution can be selected by parameter Pr169. ranging
from 12 to 20 bit. The parameter change is effective the
next time the drive is powered up.
Page 108 of 233
Res.
1
1
1
1step
1step
1rpm
1
1
1
2Pr[169]
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Binary parameters
Description
Par.
Feedback direction. When the bit is set to 1, the motor
b170.0
rotation is inverted.
Reset 1. Reset command type 1: this is used to reset the
b170.1
position reference counters and the motor reference
counters. Self resetting
Reset 2. Reset command type 2: the position reference
b170.2
counter, Pr130:131 (“theoretical” position), gets the same
value as the motor “real” position Pr132:133. Self resetting.
Reset 3. Reset command type 3.(Pr212:213=Pr2. Self
b170.3
resetting
Servo error 1. b170.4 will be set to 1 if the position error as
b170.4
an absolute value exceeds the value set in Pr140.
Servo error 2. b170.5 will be set to 1 if the position error as
b170.5
an absolute value exceeds the value set in Pr142.
Position loop feedback selection. Position loop feedback
b170.14
selection bit **
Position loop feedback selection. Position loop feedback
b170.15
selection bit **
b170.15
0
0
1
1
**
FBK A
FBK B
FBK C
Reserved (“00” automatic reset)
Page 109 of 233
Field
W
Def.
0
W
0
W
0
W
0
R
0
R
0
W
0
W
0
b170.14
0
1
0
1
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
12.2 Torque control (operating mode 110)
By this operating mode it is possible to control the current supplied to the motor and the
consequent torque to the mechanical system in two selectable modes, using bit b39.2. When
b39.2=0 (default), speed control is operating to manage the limit speed Pr190 with an available
torque which is directly proportional to the value of Pr7.
Set parameter Pr181=110 so as to activate the operating mode and give a command to set the
default parameters with b42.13. Set Pr2=1000 (10V=100.0 % of the torque), b40.0=0, b40.12=0,
b40.2=1 in order to enable the reserved reference Pr190 so as to limit the motor maximum speed.
b39.2=1 can be used to select servo torque management. In this mode the speed loop is
overridden and therefore it does not need to be constantly tuned.
Maximum
speed
Band limiter
Pr190
Pr6
-1
Pr7
Mean
reference
Pr18
1
Tourque monitor
Pr35
Reservede reference
“0”
1
Tourque limit
Current limit
Pr174
-1
OPERATING MODE 110 PARAMETERS
Field Range Def. Res.
Description
Par.
Pr190 Maximum speed. This parameter is used to limit the W &14000 3000 1 rpm
absolute maximum speed of the motor during torque
[rpm]
operation.
Page 110 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
12.3 Electrical shaft and positioned (op. mod. 120)
Operating mode 120 is the algebric sum of the 3 delta of position generators :
- Position reference from the trapezoidal profile
- Position reference from the electrical shaft generator
- Position reference from the speed mode
Each reference can be selected and entered independently.
Trapezoidal
positioner
+
Electrical shaft
+
Resulting position
reference
+
Speed mode
12.3.1 Speed mode:
This command is in Pr190. It can be used in order to move the motor within the selected
operating mode as if it were in speed mode, through a parameter-controlled ramp used to link
any changes in the speed parameter Pr190.
12.3.2 Electrical axis:
In the “Electrical axis” mode, the motor, called slave, can follow a motor called master, by
means of digital reference signals.
The reference for the electrical axis can be sent by a digital bus encoder or by ports B or C. The
desired reference selection is made through binary parameters following the block diagram
according to the table below:
REFERENCE SELECTION
Input
Mode description
SinCos + EnDat
Pr62=0
Number of pulses
Pr58
SinCos
Pr62=1
Number of pulses
Pr58
Quadrature
increm. encoder
Pr62=3
Encoder increm.
in freq/direzione
Pr62=4
Page 111 of 233
X7
Vdc
Encoder power
supply
5 b65.7=0
8 b65.7=0
12 b65.7=1
b65.6=0
b65.6=1
b65.6=0
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
REFERENCE SELECTION
SinCos +
Hiperface
Mode description
Number of pulses
Pr62=7
Pr58
Quadrature
increm. encoder
Pr63=3
Freq./direction
increm. encoder
Pr63=4
Quadrature IN2
IN3 inputs
Pr63=5
fenc in ≤ 400kHz
Freq./direction
IN2 IN3 inputs
Pr63=6
fenc in ≤ 400kHz
Quadrature IN2
IN3 inputs
Pr62=5
fenc in ≤ 400kHz
Freq./direction
IN2 IN3 inputs
Pr62=6
fenc in ≤ 400kHz
Input
X9
X5
It is important to consider that the feedback signal constrains the input configuration parameter:
parameter Pr62 is related to ports X7 and X5, whereas parameter Pr63 refers to ports X9 and
X5. These two parameters also have the same meaning. If you want to use a reference signal,
this will have to be connected to the free input in order to be used.
Fin: is the input frequency, that is:
{encoder _ pulses}× {speed [rpm]} ≤ 400 [kHz ]
Fin =
60 [sec/ min ]
Pr7: is the motor rpm speed:
Pr 7 =
Thus Pr4 has a value of:
Pr 4 =
Fin • Pr 4 • 2
2.000.000
Pr 7 • 2.000.000
2 • Fin
Pr4 is the full scale value to be entered into the converter in order to get the motor speed and
input frequencies. If the system is not in quadrature mode but in frequency/direction mode, the
speed will be 4 times lower.
Besides the physical reference signal, a reference can be selected on Digital Bus via CAN,
enabling b170.12=1 for the encoder counter B and setting b170.11=1 for encoder counter C.
Either the immediate enable bits or events can be used to engage the electrical axis, with or
without phase recovery.
The tracking mode control and regulation are performed through the parameter-controlled ramps.
The phase recovery function can also be used, (to recover the time lost during the engaging
process at acceleration).
Page 112 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
The phase recovery when the function is active is outlined in the figure above. Parameter Pr 189
is used to define the maximum velocity at which the slave recovers the space lost to the master.
The axis ratio can be set by parameter Pr187, that is the reference signal multiplier, as well as by
Pr188, which is the reference signal divider. A report can be directly sent to the signal of encoder
port B, Pr156/Pr157, and of encoder port C, Pr154/Pr155.
The slave axis is engaged to the master either immediately or when an event occurs. The choice
is made on two separate bits. A bit signals when the axis is engaged.
The axis can be disengaged either immediately or through the disengage bit.
12.3.3 Positioner
The “Positioner” function performs the task to bring the motor from the “actual position” to the
position set in the “Final position” parameter.
The positioner start is automatically generated when the “Final position” and the “Actual
position” values are different, keeping in mind that the motion parameter assessment in relation
to the positioner start can be performed only by bit b230.4=1.
With bit b230.4=0 the positioner start cannot be performed. The motion parameters are variables
defining the “Final position”, the motor speed and the linear deceleration ramp.
This type of positioning is called “Trapezoidal profile”. The motor actually moves only if bit
b230.9=1.
12.3.4 TAB0: profiles in memory
In OPM120 is possible use the TAB0 to memory up to 51 trapezoidal profiles, and for everyone
is possible memorize the speed, the acceleration ramp, the deceleration ramp and the final
position in double word.
The Pr193 parameter contains the number of the profile to execute, with b231.10=1 bit the
function is able to transfer the block of 5 variables of profile in the positioner variables.
TAB0 1a word – speed – Pr182
TAB0 2a word – acc ramp – Pr183
TAB0 3a word – dec ramp – Pr184
TAB0 4a e 5aword – final position – Pr213:212
With the qualified function, b231.10=1, is possible execute automatically another profile, simply
setting up in the pointer parameter, Pr193, another value. Every scansion, the parameters are
transferred from the table to the positioner variables, if the function is able, b231.10=1.
In order to insert the values in variables of TAB0, using the “configuration” tool it is necessary
open the “monitor” window, where it is possible to access from Pr2048 to Pr2302 parameter,
where there are the variables of the 51 trapezoidal profiles, and it possible read and modify them.
Page 113 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
To insert the values via keypad, it necessary selects TAB0 (T0), indicate the variable of TAB0
(from 0 to 254), and in the inferior line write the width of the parameter.
It is necessary save the parameters for guarantee the memory of the profiles inserted.
Pointer to table Pr193
0
1
49
50
b231.10=1 TAB0 activation by profiles
TAB0 point
Positioner variables
Speed
0
Pr182
Accel. ramp.
1
Pr183
Decel. ramp.
2
Pr184
3
Pr212
Final position
4
Pr213
Speed
5
Pr182
Accel. ramp.
6
Pr183
Decel. ramp.
7
Pr184
8
Pr212
Final position
9
Pr213
245
246
247
248
249
250
251
252
253
254
Pr182
Pr183
Pr184
Pr212
Pr213
Pr182
Pr183
Pr184
Pr212
Pr213
Page 114 of 233
Speed
Accel. ramp.
Decel. ramp.
Final position
Speed
Accel. ramp.
Decel. ramp.
Final position
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
OPM120
Position multiplier –
encoder B
b170.12
Ref.
choice
Digital
Bus encoder
b231.0
Pr201:200=213:212=0
Reset 2
b231.1
Pr201:200=213:212=131:130
Reset 3
b231.2
Pr201:200=213:212=131:130=133:132
b170.11
Acceleration
speed
Pr183
Position divider encoder B
Pr182
Pr154
Pr155
Pr151:150
Input counter
encoder C
Position divider encoder C
Posizione finale
Master
speed
Posizione attuale
b230.4
Pr213:212
Pr201:200
Pr186
Electrical shaft
engaged
Acceleration
ramp
Reference multiplier
b231.3
Pr203:202=0
Pr187
Pr188
b231.4
Pr203:202=131:130=133:132
Reference divider
Pr185
Engage at
event
Release
b231.7
Engage
b231.8
With
phase
recovery
Pr203:202
b230.9
b230.2
b230.6
Pr189
b230.13
Speed FFWD
enable
b230.3
b230.11
Edge
IN2
Value captured
b165.4
b165.3
b165.2
b39.14
Pr131:130
Position
reference
Pr161:160
Edge
IN1
b230.10
Actual position
Max speed
Neg. Edge
IN0
Pr184
B230.1
Reset 2
Pos. Edge
IN0
b230.12
Pr153:152
Reset 1
Z Enc. C
Full speed
Deceleration
time
Position multiplier – encoder C
From
C
Speed FFWD
enable
b230.0
Input counter
encoder B
Pr156
Pr157
From
B
Active positioner
Reset 1
b165.15
Motor value
captured
b39.15
Speed
Acceleration
Actual position
Pr190
Pr191
Pr205:204
Reset 1
Page 115 of 233
b231.5
Pr190=0
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Decimal parameters for operating mode 120
Description
Field Range Def. Res.
Par.
Trapezoidal positioner speed in operating mode W 0÷14000 1000 1 rpm
Pr182
[rpm]
120. This is the full speed that will be used during
the generation of the position profile.
0÷4500 500 0.001s
Trapezoidal positioner speed in operating mode W
Pr183
[s/krpm]
120. This is defined as the time in ms, Pr183, needed
to go from 0 to 1000 rpm.
0÷4500 500 0.001s
Trapezoidal positioner deceleration in operating W
Pr184
[s/krpm]
mode 120. This is defined as the time in ms, Pr183,
needed to go from 1000 rpm to 0.
0÷4500 500 0.001s
Electrical shaft ramp in operating mode 120. This W
Pr185
[s/krpm]
is used to set the acceleration and deceleration ramps
of the electrical shaft, expressed in ms from 0 to
1000rpm.
[rpm]
1 rpm
Encoder-in
rotation speed (master). Indicates the R
Pr186
input reference frequency translated into rpm (based
on 4096 pulses/revolution).
Reference multiplier (master). Using this W
-32768
1
1
Pr187
parameter and Pr188, the user can set the desired
÷32767
input reference frequency ratio.
Reference divider (master). Using this parameter W
-32768
1
1
Pr188
and Pr187, the user can set the desired input
÷32767
reference frequency ratio.
Maximum speed OM120. Sets the maximum speed. W 0÷14000 3000 1 rpm
Pr189
[rpm]
Speed mode OM120. Sets a motor speed level W 0÷14000 0 1 rpm
Pr190
disregarding any other conditions.
[rpm]
W
0÷4500 500 0.001s
Speed mode: Pr190 ramp.
Pr191
[s/krpm]
±231
1step
Pr201:200 Actual position (positioner). Read-only parameter. R
Indicates the reference position of the trapezoidal
[step]
profile.
±231
1step
Pr203:202 Actual position (electrical shaft). Read-only R
parameter. Indicates the reference position of the
[step]
electrical shaft.
±231
1step
Pr205:204 Actual position (speed mode). Read-only R
parameter. Indicates the reference position of the
[step]
speed mode.
±231
0
1
Pr213:212 Final target trapezoidal positioner value in W
[step]
OM120. Register where the desired final position is
entered.
Page 116 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Binary parameters
Description
Field Def.
Par.
0
b170.12 Encoder B enters position reference on digital bus (reserved). (1)
W
Theoretical
profile
running.
When
the
bit
is
1,
it
means
that
the
R
0
b230.0
trapezoidal positioner theoretical profile is running.
W
0
b230.1 ENC B or C selected as electrical shaft master. B230=1,
ENC B has been selected.
0
b230.2 “Engaged” electrical shaft. (1) Engaged electrical shaft. During the R
engaging phase, when the ramp (Pr183) is not 0, this bit indicates the end
of the transitory phase.
0
b230.3 Electrical shaft engaged at B capture event. Activates engagement on a W
sensor selected by bits 2, 3 and 4 of b165. The captured level from the
master is downloaded in Pr161:160. The space lost during data processing
is recovered.
1
b230.4 Activates trapezoidal positioner target change. (1) Activates trapezoidal W
positioner target change.
W
0
b230.6 Engage electrical shaft with phase recovery. (1)
W
1
b230.9 Enables trapezoidal positioner reference. (1)
Enables
electrical
shaft
reference.
(1)
W
1
b230.10
W
1
b230.11 Enables speed mode reference.
0
b230.12 Trapezoidal positioner speed FFW. (1) enables trapezoidal positioner W
speed FFW component.
1
b230.13 Electrical shaft speed FFW. (1) enables electrical shaft speed FFW W
component. [w].
0
b231.0 Type 1 trapezoidal positioner reset. Type 1 trapezoidal positioner reset W
command ( Pr201:200=Pr213:212=0).
0
b231.1 Type 2 trapezoidal positioner reset. Type 2 trapezoidal positioner reset W
command ( Pr201:200=Pr213:212=Pr131:130).
0
b231.2 Type 3 trapezoidal positioner reset. Type 2 trapezoidal positioner reset W
command ( Pr201:200 = Pr213:212 =Pr131:130=Pr133:132). Command
used to reset the profile and setting the actual position of the trapezoidal
positioner to the motor FBK value.
0
b231.3 Type 1 electrical shaft reset. Type 1 electrical shaft reset command W
(reference_alb_ele=0 Pr 203:202=0). The actual electrical shaft position is
reset.
0
b231.4 Type 2 electrical shaft reset. Type 2 electrical shaft reset command W
Pr203:202=131:130=133:132.
0
b231.5 Type 1 speed mode reset. Type 1 speed mode reset command. Command W
used to reset the speed Pr190=0. The speed mode reference position is also
reset.
0
b231.7 Electrical shaft release. Command used to release the slave from the W
master. Self-resetting.
0
b231.8 Electrical shaft engage. Command used to engage the slave to the master W
reference master. Self resetting
Page 117 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
12.4 Electronic came (OPM121)
This program is a preset motion mode in the drive’s basic configuration, that can be programmed
by selecting the following parameters: Pr181=121, b42.13=1, default setting of the selected
operating mode.
Some of the most widely used motion functions of industrial automation are available within this
mode. Namely, this operating mode includes the following:
- position reference generator (positioner)
- speed mode generator
- cam1 generator
- cam2 generator
The resulting position reference will therefore be the algebric sum of the position reference
deltas of one or more generators.
Positionator
Speed mode
+
+
Cam 1
+
+
Resulting position
reference
Cam 2
This diagram allows to identify a general flow in operating mode 121. If you carefully analyze
this mode through the block diagram, you will see that the programmer can use several enabling
commands (programmable bits ) at different levels in order to address the flow of the generated
position reference (or references), in several display modes. For instance, for each generator a
position reference can be enabled on a position counter. From here the reference will then be
downloaded in the position loop or into a general position counter.
Position loop
Positioner
reference
generator
Modul global
counter
Generator
counter
Global
counter
at modul
Incremental global
counter
When the position reference of at least one generator is enabled in the position loop, the
reference loading into a global counter defined by module is automatically enabled.
Page 118 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
12.4.1 Posizionator
This is a trapezoidal profile generator, with the following user-definable parameters:
- speed profile
- acceleration
- deceleration
- final value in motor step
The parameters referred to the positioner levels, final position Pr211: 210 and actual position
Pr201:200, are absolute. However, they are subsequently transferred to the other adjustment
parameters following the block diagram.
The thus position reference generated in this way is loaded into the position loop as well as in the
global counter. The generated reference, activated through a bit command, is then loaded as an
addition to the master in both generators CAM1 and CAM2.
12.4.2 Speed mode
This is a position generator, but it is set as a speed reference. The following parameters will have
to be set:
ƒ Rpm speed
ƒ acceleration
12.4.3 CAM1 and CAM2
The two CAM generators are specifically designed to meet the requirements of automatic
machines using electronic cams. Four tables are available, namely TAB0, TAB1, TAB2 and
TAB3, that have been implemented to perform a series of cam functions. Each table is described
by a vector made of 257 elements, that indicate the position to be taken by the controlled axis
when the motor axis is in the position:
slave function =
element number • master modul
256
In each table the value of the vector elements is ranging between 0 and 9999, whereas 10,000
shall be the count number set in the slave module parameter.
In order to generate a table, the axis route must be divided into 257 points; the value of each
point will have to be rated to 10000, because this is the maximum value that can be written in the
table elements.
The 257th element of each table defines the cam as closed if it is = 0, or as open if it is = 10,000.
The motion will be able to perform the points listed in the table; if the required speed and torque
are within the motor’s electric limits (Maximum Speed and Torque).
Through a series of parameters it is possible to automatically program one of the motion laws
that have been set in the drive in one of the four tables. Functions can be retrieved as follows:
Page 119 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Motion law
Motion law
selection by Pr182
y=x
1
y=x-[sen (x)]
2
Table selection
by Pr183
Tab0=Pr183=0
Triangular profile
3
Tab1=Pr183=1
Engage ramp
4
Disengage ramp
5
y=sen(x)
6
Tab2=Pr183=2
Tab3=Pr183=3
After selecting the function by Pr182, the parameter is automatically set to zero.
The four tables are the same in both CAM generators; the same table with the same function can
be selected in both generators.
As a default drive configuration, TAB0 is active in CAM1 and TAB3 is active in CAM2. In
order to change the default setting there are some immediate commands active for both CAM
generators, or for CAM1 only of the enable commands on programmable master phase.
When the selected table is changed, the two generators will have a different behaviour.
Based on the executed command, CAM1 immediately activates the execution of the selected
table as well as a change of module. The user will have to check the continuity of speed and
torque during table and module changes. Modules with negative sign cannot be set in CAM1.
CAM1 is engaged either by direct command or through an engage and disengage command on
programmable master phases.
CAM2 activates the selection of a new table and the change of module only by an engage
command. A module with negative sign can be set in CAM2. CAM2 will be engaged and
disengaged only by command and always when the master is in phase 0, or by a single execution
command (Single Shoot). If during the disengage phase bit 233.1 is activated in CAM2, the
program automatically goes to master phase zero and performs the calculation of the table and of
the set module, as well the engagement with the new settings.
The above described cams can be connected to either of two masters. Specific commands allow
to select either one or the other master for both cams, also the same one for both.
The masters are programmed by two pointer parameters allowing to select as a master position
reference any parameter of the drive. The user will have to select as pointer a parameter that has
a meaning for the used motion.
Master 1 offers the possibility to enable a linear ramp to be used whenever the pointed reference
must be changed.
As a default configuration, the cams are scanned throughout the master module. In both masters
the selected cams can be scaled in a sector of the master module by programming the starting
point and the space in which the cam shall be executed. It is possible of course to scan the cam in
this way also between two master modules. The scaling is engaged by the masters, not by the
cam generators, and therefore, if the same master is selected, it will be impossible to scale
CAM1 and CAM2 functions in two separate sectors. You will have to program two masters with
the same pointer and the same initial phasing, then engage both cams to the masters and scale
them in separate sectors.
Page 120 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
12.4.3.1 Automatic activation of CAM tables
Beside enabling tables on programmable master phase or by immediate command as shown
above, the drive offers a default function providing for an automatic sequence to enable the
tables.
The operation is enabled through the activation of bit 231.12 and by using bit 231.13 command
in order to start per an engaging sequence or bit 231.14 command in order to start per a
disengaging sequence. The switch between active tables always occurs during master phase 0.
Tab1 and Tab2 are used as a link during the switch between Tab0 and Tab3 and the other way
round, and therefore they cannot be active longer than one master module.
T0
T0
T1
T2
T1
T2
T3
T3
Master with positive speed
Master with negative speed
As shown in the figures, the table switching sequence is automatically inverted when the speed is
negative.
The above-described function is essential, for instance, in applications where the user wants to
complete an engage/disengage phase starting from a gearing function (Electrical axis) by means
of linear linking ramps.
By linear links we mean the tables describing the two engage and disengage ramps. Let’s
suppose that Tab0 has been programmed with a y=x function (gearing) and that Tab3 has been
programmed as a fixed axis, that is y=constant K. We will need to calculate both linking tables in
Tab1 and Tab2 to be able to engage and disengage the axis.
If we consider, for instance, the master cycle in a module in degrees (360°), we will have to set
in Pr186 the master module sector value (ranging between 0° and 360°) that we are going to use
in order to perform the two engaging and disengaging ramps.
Use Pr.183 to select the table you need to calculate and Pr182 to retrieve the drive’s base
configuration predefined functions del drive; in this way you will automatically calculate the
curves in the engaging and disengaging tables.
-Engaging Tab.1 calculation:
Pr.183=1 ( Table 1) and Pr182=4 ( Engaging function);
-Disengaging Tab.2 calculation: Pr.183=2 ( Table 2) and Pr182=5 ( Engaging function);
In order to use this application it is necessary to program a table with a constant value in all of its
points. Tab.3 is a suitable table for this purpose and it can be replaced by a virtual table using
commands b232.9 for CAM1 and b232.10 for CAM2. The value of the constant to be set can be
taken in Pr184 for CAM1 and in Pr185 for CAM2, by reading the first value of the engage table
in Tab1, and the last value of the disengage table in Tab2.
Page 121 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
b231.14
Disengage
comand
b231.13
Engage
comand
Pr186
engage
ramp
sector
Tab 3
0°
Master modul
Pr186
Disengage
ramp
sector
Tab 1
360°
0°
Master modul
Tab 0
360°
0°
Tab 2
360°
0°
Master modul
Master modul
Tab 3
360°
0°
Master modul
360°
Speed curve for slave axe
The above described tables are of course an example case to describe the engage and disengage
functions of an axis by changing tables, and they are calculated in order to allow these functions
for an axis that needs to be dynamically disengaged/engaged according to a gearing law (y=x).
Of course it is possible to describe different tables for similar functions and load them in the
relevant addresses. The user will have to draw the curves in order not to create any motion
discontinuities on the axis, especially when switching between tables. In order to accomplish this
and more generally to ensure user access to cam tables, these can be either read and written using
the keypad or through SBC Can or serial port RS422 using address 4096 (adjacent areas of 257
words per table):
Keypad
SBC Can or serial
Tab.0
4096<=address<=(4096+513);
Tab.1
read and write
(4096+514)<=address<=(4096+1027);
Tab.2
directly
(4096+1028)<=address<=(4096+1541);
Tab.3
(4096+1542)<=address<=(4096+2055);
Oppure per quanto riguarda la versione con Canopen le tabelle sono accessibili tramite SDO
come segue:
CAN Open
Tab.0: Points 0….254 Index 0x2008
Points 255…256 Index 0x2009
Tab.1: Points 0….254 Index 0x200A
Points 255…256 Index 0x200B
Tab.2: Points 0….254 Index 0x200C
Points 255…256 Index 0x200D
Tab.3: Points 0….254 Index 0x200E
Points 255…256 Index 0x200F
Sub-index
Sub-index
Sub-index
Sub-index
Sub-index
Sub-index
Sub-index
Sub-index
1…255
1….2
1…255
1….2
1…255
1….2
1…255
1….2
Page 122 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Profile running
b233.0
Final position
Pr211:210
acceleration
Positioner
reference
Pr201:200
Reset 1
b232.0
Pr211:210=Pr201:200
speed
Pr189
Reset 1
b232.1
Pr211:210=Pr201:200=Pr131:130
deceleration
Pr191
Pr190
Reset 3
b232.2
Pr211:210=Pr201:200=Pr131:130=Pr133:132
Positionator
b230.4
Pr281:280
b233.8
Enable FFW
b231.0
b231.4
Pr247:246
Master phase
for TAB0 engag.
MASTER 1
b230.0
b232.4
Pr194
Ramp
Counter
Pr217:216
Module
Pr225:224
Pr221:220
Master axis
position in
module
b230.3
Pr251:250
Master phase for
TAB2 engag.
Cam width
Counter
Pr193
Pr219:218
Module
Pr223:222
Master axis
position in
module
b231.6
Pr235:234
Pr237:236
b233.9
CAM1 reference
Enable FFw
Pr203:202
TAB1
b231.9
b231.7
CAM1
b232.6
Phase for CAM 1
TAB2
Pr197:196 engaging
b231.10
b232.7
TAB3
b231.11
Pr199:198
Phase for CAM1
release
b232.8
TAB1
TAB2
TAB3
b232.11
Engaging
b232.12
Releasing
Global counter
b232.13
TAB0
b232.15
Engage/released
on CAM1
Signal TAB
active
Selection of table
b232.5
Pr283:282
Pr239:238
Cam width
MASTER 2
CAM1 generator
counter
b230.5
Module
DATA
CAM
1
Signal TAB
active
b231.3
Pr253:252
Master phase
for TAB3 engag.
b231.8
Signal TAB
active
Signal TAB
active
b231.2
Pr227:226
Cam starting point
Pr215:214
b231.5
Cam starting point
b230.2
Pr213:212
Pr249:248
Master phase
for TAB1 engag.
b232.14
Pr192
b231.1
Trap. Positioner
counter
TAB0
DATA
CAM
2
Module
Sigle shot
Pr289:288
b230.8
b230.12
b230.9
b230.13
b230.10
b230.14
Pos. In module
Pr245:244
Pr243:242
Pr131:130
b231.15
Pr241:240
b230.11
Reference position
b230.15
b230.6
Pr285:284
CAM2
Pr205:204
Position in module
CAM2 generator
counter
b233.10
Enable FFW
speed
Ramp
Pr188
Page 123 of 233
Pr187
b230.7
Pr287:286
Speed mode counter
Module
Reset 1
b232.3
Pr187=0
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Decimal parameters for operating mode 121
Field Range Def. Res.
Description
Par.
Selection of function type. Parameter of selection of W
0÷6
0
1
Pr182
the law of motion in order to generate the points in
table, like from paragraph CAM1 and CAM2. This
parameter doesn’t come configured from the display,
but it can be controlled through serial ways, field bus
and MotionWiz. It is an autoreset parameter.
Selection of internal function calculation table. W
0÷3
0
1
Pr183
See the table in par. CAM1 and CAM2.
-32768
0
1
Pr184
Value of CAM1 dummy table (Tab3). If active the W
÷32767
fictitious table, comes considered only this value for
the position of the motor in CAM1.
Value of CAM2 dummy table (Tab3). If active the W
-32768
0
1
Pr185
factitious table, comes considered only this value for
÷32767
the position of the motor in CAM2 in place of one
table CAM.
Value
in degrees of the linear engage ramp master W
0÷360
60
1°
Pr186
module. Field of the module master in which the
[°]
motor it executes the ramp. The tables must be
loaded after to have set up this parameter.
0
1rpm
Pr187
Speed in speed mode. It lets to move in speed the W ±14000
[rpm]
motor remaining in the operative mode (Pb40.2=1).
Speed mode ace. Ramp. Is the ramp in ms from 0 to W 2÷4500 500 1ms
Pr188
1000 rpm that it manages the variations of speed of
[ms]
Pr187.
Max positioner speed. Is the maximum speed, in W 0÷14000 1000 1rpm
Pr189
rpm, that the positioner can make.
[rpm]
Positioner acceleration time. Is the ramp in ms from W 2÷4500 500 1ms
Pr190
0 to 1000 rpm that it connects the variations of speed,
[ms]
Pr189, of positioner.
Positioner deceleration time. Is the ramp in ms W 2÷4500 500 1ms
Pr191
from 0 to 1000 rpm that it connects the variations of
[ms]
speed, Pr189, of positioner.
First Master1 reference pointer. It contains the W
0÷384
150
1
Pr192
parameter that it references to the Master1.
Second Master2 reference pointer. It contains the W
0÷384
150
1
Pr193
parameter that it references to the Master2.
Master 1 linking ramp. It is the ramp, in sixteenth W 0÷32000 100
1
Pr194
of count to ms, which manages the variations of the
Master1.
±231
0
1
Pr197:196 Master axis phase for CAM1 engaging. If it is able, W
when the module of CAM1 catches up with this
position, comes the CAM1 engaging.
0÷6
0
1
Pr199:198 Master axis phase for CAMI1 release. If it is able, W
when the module of CAM1 catches up with this
position, comes the CAM1 release.
0÷3
0
1
Pr201:200 Trap. Positioner reference. When this quota catches W
up with the value of Pr211:210, the generation of the
profile is finished.
W
-32768
0
1
Pr203:202 CAM1 reference. Position of CAM2 in its module.
÷32767
W
-32768
0
1
Pr205:204 CAM2 reference. Position of CAM2 in its module.
÷32767
Page 124 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Description
Field Range Def. Res.
Par.
Final
position
(Trap.
positioner).
It
represents
the
W
0÷360
60
1°
Pr211:210
quota of which the position of the motor is wanted to
[°]
be increased.
0
1rpm
Pr213:212 Pointer 1 master incremental encoder. This W ±14000
[rpm]
parameter contains all the increments sendes to you
from the pointer parameter.
Pr215:214 Pointer 2 master incremental encoder. This W 2÷4500 500 1ms
parameter contains all the increments sendes to you
[ms]
from the pointer parameter.
±231
10000 1rpm
Pr217:216 Master 1 axis module (Pointer 1). It contains the W
number of count for which the axis Master 1 it is
repeated.
±231
10000 1ms
Pr219:218 Master 2 axis module (Pointer 2). It contains the W
number of count for which the axis Master 2 it is
repeated.
W
1ms
Master
1 axis position in module
±231
0
Pr221:220
31
W
1
±2
0
Pr223:222 Master 2 axis position in module
31
W
1
±2
0
Pr225:224 CAM1 scaling –cam starting point
31
W
±2
10000 1
Pr227:226 CAM1 scaling- Cam width (step)
31
W
1
±2
0
Pr235:234 CAM2 scaling –cam starting point
31
W
±2
10000 1
Pr237:236 CAM2 scaling- Cam width (step)
31
W
±2
10000 1
Pr239:238 CAM1 module
31
W
±2
10000 1
Pr241:240 CAM2 module
31
±2
10000 1
Pr243:242 Reference module (sum of all enabled generators W
POS+SM+CAM1+CAM2)
W
0÷360
60
1°
Pr245:244 Axis position in the reference module
[°]
0
1rpm
Pr247:246 Master phase for Tab0 engaging. The value entered W ±14000
[rpm]
in the register identifies the master value . When the
master phase matches the programmed value, bit
b231.0 is set to 1, then the slave engages to the
master with a trend generated by TAB0.
Pr249:248 Master phase for Tab1 engaging. The value entered W 2÷4500 500 1ms
in the register identifies the master value . When the
[ms]
master phase matches the programmed value, the
slave engages to the master with a trend generated by
TAB1.
±231
0
1
Pr251:250 Master phase for Tab2 engaging. The value entered W
in the register identifies the master value . When the
master phase matches the programmed value, the
slave engages to the master with a trend generated by
TAB2.
±231
0
1
Pr253:252 Master phase for Tab3 engaging. The value entered W
in the register identifies the master value . When the
master phase matches the programmed value, the
slave engages to the master with a trend generated by
TAB3.
W
±231
0
1
Pr281:280 Trap. Positioner counter.
31
W
±2
0
1
Pr283:282 CAM1 generator counter
31
CAM2
generator
counter
W
±2
0
1
Pr285:284
W
±231
0
1
Pr287:286 Speed mode counter
Page 125 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Description
Field Range
Par.
Global
counter
(sum
of
all
enabled
generators
W
±231
Pr289:288
POS+SM+CAM1+CAM2)
Def.
0
Res.
1
Binary parameters
Description
Field Def.
Par.
0
b230.0 (1) bypasses Master1 change linking ramp (0) Ramping.
W
0
b230.2 Enables Master1 displacement from profile generator
W
0
b230.3 Enables Master2 displacement from profile generator
W
0
b230.4 Enables positioner in the counter (Pr281:280)
W
0
b230.5 EnableCAM1 generator in the counter (Pr283:282)
W
0
b230.6 Enables CAM2 generator in the counter (Pr285:284)
W
Enables
speed
mode
in
the
counter
(Pr287:286)
0
b230.7
W
0
b230.8 Enables positioner counter (Pr281:280) in the global counter W
(Pr289:288)
0
b230.9 Enables CAM1 counter (Pr283:282) in the global counter (Pr289:288)
W
0
b230.10 Enables CAM2 counter (Pr285:284) in the global counter (Pr289:288)
W
0
b230.11 Enables speed mode counter (Pr287:286) in the global counter W
(Pr289:288)
0
b230.12 Enables positioner counter (Pr281:281) in the position reference (Pr W
131:130)
0
b230.13 Enables CAM1 counter (Pr283:282) in the position reference (Pr W
131:130)
0
b230.14 Enables CAM2 counter (Pr285:285) in the position reference (Pr W
131:130)
0
b230.15 Enables speed mode counter (Pr287:286) in the position reference (Pr W
131:130)
0
b231.0 Activates table Tab0 to the Master phase set in (Pr247:246). When the W
bit is 1, TAB0 is enabled. The table is enabled when the slave-master
engagement level is programmed in parameter Pr247:246.
Activates
table Tab1 to the Master phase set in (Pr249:248). When the W
0
b231.1
bit is 1, TAB1 is enabled. The table is enabled when the slave-master
engagement level is programmed in parameter Pr249:248.
0
b231.2 Activates table Tab2 to the Master phase set in (Pr251:250). When the W
bit is 1, TAB2 is enabled. The table is enabled when the slave-master
engagement level is programmed in parameter Pr251:250.
0
b231.3 Activates table Tab3 to the Master phase set in (Pr253:252). When the W
bit is 1, TAB3 is enabled. The table is enabled when the slave-master
engagement level is programmed in parameter Pr253:252.
0
b231.4 Immediate activation of Tab0. When the bit is set to 1, TAB0 is W
immediately engaged.
0
b231.5 Immediate activation of Tab1. When the bit is set to 1, TAB1 is W
immediately engaged.
0
b231.6 Immediate activation of Tab2. When the bit is set to 1, TAB2 is W
immediately engaged.
0
b231.7 Immediate activation of Tab3. When the bit is set to 1, TAB3 is W
immediately engaged.
0
b231.8 Signals Tab0 is active in CAM1 generator. When TAB0 is used in the R
cam generator, the bit is 1.
0
b231.9 Signals Tab1 is active in CAM1 generator. When 1s used in the cam R
generator, the bit is 1.
Page 126 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Description
Field Def.
Par.
Signals
Tab2
is
active
in
CAM1
generator.
When
TAB2
is
used
in
the
0
b231.10
R
cam generator, the bit is 1.
0
b231.11 Signals Tab3 is active in CAM1 generator. When TAB3 is used in the R
cam generator, the bit is 1.
0
b231.12 Enables automatic table switching sequence
W
0
b231.13 Command used to activate switching sequence to Tab0
W
0
b231.14 Command used to activate switching sequence to Tab3
W
0
b231.15 Immediate command and CAM2 engage/released state
W
0
b232.0 Type 1 positioner reset command (Pr211:210=Pr201:200=0)
W
0
b232.1 Type 2 positioner reset command (Pr211:210=Pr201:200=Pr131=130)
W
3
positioner
reset
command W
0
b232.2 Type
(Pr211:210=Pr201:200=Pr131=130=Pr133:132)
0
b232.3 Speed mode reset command ( Pr187=0)
W
0
b232.4 CAM1 selector to select Master 1 or 2
W
CAM2
selector
to
select
Master
1
or
2
0
b232.5
W
0
b232.6 Activates CAM1 engage to the Master phase set in (Pr197:196).
W
0
b232.7 Activates CAM1 release to the Master phase set in (Pr199:198).
W
0
b232.8 Immediate command and CAM1 engage/released state
W
0
b232.9 Enables dummy table in Tab3 with value set in Pr184 in CAM1
W
0
b232.10 Enables dummy table in Tab3 with value set in Pr185 in CAM2
W
0
b232.11 Command engaging to CAM2 master phase 0
W
Command
releasing
to
CAM2
master
phase
0
0
b232.12
W
0
b232.13 Single shot execution command (one module) to the CAM2 master W
phase 0.
0
b232.14 Selection of table to be performed in CAM2. The state of this bit, W
together with bit b232.15, identifies the selected table (see table below*).
0
b232.15 Selection of table to be performed in CAM2. The state of this bit, W
together with bit b232.14, identifies the selected table (see table below*).
0
b233.0 Theoretical trapezoidal profile running.
W
0
b233.1 Command used to update the table and module in CAM2
W
0
b233.8 Enables positioner speed FFW
W
0
b233.9 Enables CAM1 generator speed FFW
W
0
b233.10 Enables CAM2 generator speed FFW
W
* Table Selection
TAB0
TAB1
TAB2
TAB3
b232.15
0
1
1
0
Page 127 of 233
b232.14
1
0
1
0
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
12.5Electrical shaft and positioned (oper. mode 122)
The operative mode OPM122 is equal to operative mode OPM120, the difference between the
operative mode is the scanning time:
per operative mode OPM122 the scanning time is 1msec, while per operative mode OPM120 the
scanning time is 0,5msec.
This positioned mode can use the S-ramp (see the par. “ramp with “S” profile”)
b231.0
Pr201:200=213:212=0
Reset 2
b231.1
Pr201:200=213:212=131:130
Reset 3
Position multiplier –
encoder B
b170.12
Ref.
choice
Digital
Bus encoder
b170.11
b231.2
Pr201:200=213:212=131:130=133:132
Pr154
Pr155
Pr151:150
Input counter
encoder C
Position divider encoder C
Posizione finale
Master
speed
Posizione attuale
b230.4
Pr213:212
Pr201:200
Pr186
Electrical shaft
engaged
Reference multiplier
b231.3
Pr203:202=0
Pr187
Pr188
b231.4
Pr203:202=131:130=133:132
Acceleration
ramp
Pr185
Reference divider
Release
b231.7
Engage
b231.8
With
phase
recovery
Pr203:202
b230.9
b230.2
b230.6
Pr189
b230.13
Speed FFWD
enable
b230.11
b230.3
Edge
IN2
Value captured
b39.15
b165.4
b165.3
b165.2
b39.14
Pr131:130
Position
reference
Pr161:160
Edge
IN1
b230.10
Actual position
Max speed
Engage at
event
Neg. Edge
IN0
Pr184
B230.1
Reset 2
Pos. Edge
IN0
b230.12
Pr182
Pr153:152
Position divider encoder B
Reset 1
Z Enc. C
Full speed
Acceleration
speed
Pr183
Deceleration
time
Position multiplier – encoder C
From
C
Speed FFWD
enable
b230.0
Input counter
encoder B
Pr156
Pr157
From
B
Active positioner
Reset 1
b165.15
Motor value
captured
Speed
Acceleration
Actual position
Pr190
Pr191
Pr205:204
Reset 1
Page 128 of 233
b231.5
Pr190=0
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
12.6 Position control via CanBus (operating mode
140)
If operating mode 140 is enabled, Hi-drive will execute a position loop of a proportional type
with feed-forward. In this case, the profile generator is considered external and must send the
information about the position and speed reference via CanBus in accordance with the SBCCAN
protocol (see section on CanBus).
Speed FFWD
via CanBus
Speed
Feedforward
Pr182
Pr185
Feedback transmission
enable
b230.2
Position reference
via CanBus
Pr200:201
Position reference
Pr130:131
Pr203:202
Motor position
Pr133:132
Motor position
via CanBus
Feedback transmission
b230.6 enable
b230.15
Sync
Decimal parameters
Description
Field Range Def. Res.
Par.
Speed reference OM120. This is the feed-forward value W -32768 0
1
Pr182
received via the CanBus. When the SYNC (b230.15=1) is
÷32767
received, Pr182 will be copied to Pr185 and will become
active.
Cyclic command OM140. Command parameter W -32768 0
1
Pr183
managed by Pico-PLC. (see section “SBCCAN”).
÷32767
Cyclic state OM140. Status parameter managed by Pico- W -32768 0
1
Pr184
PLC. (see section “SBCCAN”).
÷32767
Speed feedforward. The value of this parameter is W -32768 0
1
Pr185
summed at the output of the position loop in order to
÷32767
obtain the speed request Pr6.
±231
0
1
Pr201:200 Position reference via CanBus. This is the position R
reference received via the CanBus. When the SYNC
(b230.15=1) is received, Pr200:201 will be copied to
Pr130:131 and will become active.
Page 129 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Description
Field Range Def. Res.
Par.
R
Motor
position
(feedback9
via
the
CanBus.
When
the
0
1
Pr203:202
SYNC (b230.15=1) is received, Pr132:133 will be copied
to Pr203:204 and, if feedback transmission has been
enabled (b230.2=1), it will automatically be transmitted
via the CanBus.
Binary parameters
Description
Field Def.
Par.
0
b230.0 8 byte response message. Cyclic response message. When the bit is 1, the W
status is made by the 16 bits in Pr184. Otherwise, when the bit is 0, the
status contains only the first 8 bits of parameter Pr184.
1
b230.2 Enabling FBK transmission to sync0. Enables fbk response to sync0. If W
= 1, when the type 0 SYNC is received, Pr202:203 will be transmitted via
the CanBus.
0
b230.3 6/7 byte response message. If bit0=0, the response message will have 7 W
bytes; If bit 0=1,the response message will have 6 bytes.
1
b230.6 Enabling FBK transmission to sync1. Enables fbk response to sync1. If W
= 1, when the type 1 SYNC is received, Pr202:203 will be transmitted via
the CanBus.
W
0
b230.7 FFW calculation. Calculates the ffw component from position reference.
b230.15 Watchdog sync. Sync receive Watchdog (set any time a message is RW 0
received).
Page 130 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
12.7 Additional useful functions
12.7.1 Capturing values
Three event-capturing functions are available to capture either the position fbk or either encoder
inputs (B or C). These functions can be programmed both in terms of the value to be captured,
that can be alternatively:
- POSITION LOOP FBK,
- ENCODER B,
- ENCODER C,
and in terms of the event when the value must be captured, that can be alternatively:
- zero encoder point dog (encoder in connector)
- rising edge of digital input IN0
- falling edge of digital input IN0
- digital input IN1 edge (programmable rise/fall through b39.14)
- digital input IN2 edge (programmable rise/fall through b39.15)
When a synchronous motor with speed feedback from an incremental encoder is used, any time
the unit is powered up a phasing procedure will have to be carried out. The phasing process may
end (if Pr65.3=1) with a “fine” phasing on the input encoder zero point dog. In this case, the
encoder will need to be mechanically phased when it is installed on the motor.
As sincos encoders can be used encoders with a number of sines per revolution corresponding to
2 elevated to the nth power.
Through the position FBK the motor position can be identified and saved in specific registers.
The drive allows to chose where to capture the value, in which of three registers to save it and
what type of event shall prompt the capture of the value.
Parameters Pr164, Pr165 and Pr166 are used to manage events, registers and captured values:
- bits 0 and 1 define which FBK shall be used to capture the value. The setting of these bits
therefore determines the data input;
- bits 2, 3 and 4 define the selection of the event that prompts the value capture: that is,
these bits identify the event that shall determine the timing of the value capture;
- bit 15 controls the value capture. This means that, any time this bit is 1, a value has been
captured. This bit, however, is not self-resetting and its status must be changed (through
Pico-PLC or serial command) in order to be able to see when the next values are sensed.
Page 131 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Event capture
X6
Position feedBack
b170.14
FBK B multiplier
Input counter Encoder B
X7
Pr62
Pr156
Pr157
b170.12
FBK C
selection
X8
Pr63
b170.11
Pr154
FBK C divider
X11
Z Enc. C
Event capture
selection
Pos.
Edge IN0
Neg.
Edge IN0
Pr159:158
Value 1 captured
Motor value captured
b165.15
Pr164
b39.14
Edge IN1
Event capture
selection
b39.15
Pr165
FBK C multiplier
Input counter Encoder C
Pr155
IN1
IN2
Pr164
FBK capture
selection
Pr153:152
FBK B divider
Motor value captured
b164.15
Pr133:132
b170.15
FBK B selection
FBK capture
selection
Pr161:160
Value 2 captured
Motor value captured
Edge IN2
Pr165
b166.15
Pr163:162
Pr151:150
Pr166
FBK capture
selection
Value 3 captured
Pr166
Event capture
selection
Page 132 of 233
Parker Hannifin S.p.A S.B.C. Division
Decimal parameters
Description
Field Range Def. Res.
Par.
1
Pr151:150 Encoder C input counter. Counter dedicated to R -32768 0
reference input from C FBK.
÷32767
1
Pr153:152 Encoder B input counter. Counter dedicated to R -32768 0
reference input from B FBK.
÷32767
Encoder C position numerator. Using this parameter W -32768 1
1
Pr154
and Pr155, the user can set the desired input reference
÷32767
frequency ratio.
Encoder C position enumerator. Using this parameter W -32768 1
1
Pr155
and Pr154, the user can set the desired input reference
÷32767
frequency ratio.
Encoder B position numerator. Using this parameter W -32768 1
1
Pr156
and Pr157, the user can set the desired input reference
÷32767
frequency ratio.
Encoder B position denominator. Using this parameter W -32768 1
1
Pr157
and Pr156, the user can set the desired input reference
÷32767
frequency ratio.
R
0
1
Pr159:158 Captured value 1. Register containing value 1.
R
0
1
Pr161:160 Captured value 2. Register containing value 2.
R
0
1
Pr163:162 Captured value 3. Register containing value 3.
Binary parameters
Description
Par.
b164.Y selection of capture object 1. The setting of bits defines the object
and the type of event to be captured.
b164
Capture
object to be captured: bit1 bit0
bit4
bit3
event
0
0
FBK POS
ENC A
ENC B
Not valid
0
1
1
1
0
1
Z ENC AUX
Not valid
POS EDGE IN0
NEG EDGE IN0
EDGE IN1
EDGE IN2
0
0
0
0
1
1
0
0
1
1
0
0
Other not valid
b164.15 Warning bit. This bit warns that a value has been captured. The bit
has no self resetting capabilities and therefore stays set to “1” after a
first value has been captured.
Capture
2 selection. The setting of these bits defines the object and
b165.Y
the type of event to be captured.
b165
Bit4
Bit3
Capture event
object to be captured: bit1 bit0
0
0
Z ENC AUX
FBK POS
ENC A
ENC B
Not valid
0
0
1
1
0
1
0
1
Not valid
POS EDGE IN0
NEG EDGE IN0
EDGE IN1
EDGE IN2
Page 133 of 233
0
0
0
1
1
0
1
1
0
0
Other not valid
Field
W
Def.
bit2
0
1
0
1
0
1
R
W
Bit2
0
1
0
1
0
1
0
Parker Hannifin S.p.A S.B.C. Division
Description
Par.
Warning
bit.
This
bit
warns
that a value has been captured. The bit
b165.15
has no self resetting capabilities and therefore stays set to “1” after a
first value has been captured.
b166.Y Capture 3 selection. The setting of these bits defines the object and
the type of event to be captured.
b166
Bit4
Bit3
Capture event
object to be captured: bit1 bit0
FBK POS
ENC A
ENC B
Not valid
0
0
1
1
0
1
0
1
Z ENC AUX
Not valid
POS EDGE IN0
NEG EDGE IN0
EDGE IN1
EDGE IN2
0
0
0
0
1
1
0
0
1
1
0
0
Other not valid
b166.15 Warning bit. This bit warns that a value has been captured. The bit
has no self resetting capabilities and therefore stays set to “1” after a
first value has been captured.
Field
R
Def.
0
W
Bit2
0
1
0
1
0
1
R
0
12.7.2 Programmable outputs
✎
Two programmable analogue outputs are available in terminal block X5: parameters Pr50 and
Pr52. The scale of the 2 analogue outputs has range between –2048 and +2048, corresponding to
±10V. An exception is made when Pr0 is monitored (in default condition); in this case the
maximum output voltage is 8.54V when the speed in Pr0 reaches the speed value of Pr32. The
output scale therefore varies according to the value of parameter Pr32 (see formula).
The scale can also me changed by parameters Pr51 and Pr53.
Pr50=Pr0, I will get:
Van.out =
Pr52=Pr0, I will get:
( value of the Pr pointed from Pr 50) • 8,54V
Pr 32 • 2Pr 51
Van.out =
( value of the Pr pointed from Pr 52) • 8,54V
Pr 32 • 2Pr 53
In the other cases:
Van.out =
( value of the Pr pointed from Pr 50) • 10V
2048 • 2Pr 51
Van.out =
Page 134 of 233
( value of the Pr pointed from Pr 52) • 10V
2048 • 2Pr 53
Parker Hannifin S.p.A S.B.C. Division
12.7.3 Encoder simulation
The simulation of encoder pulses can be seen on two different connectors, whereas the generated
signal can be taken either from the motor shaft position or from a pointed parameter.
When the value is read from the motor shaft position, the encoder simulation can set the number
of pulses per revolution (Pr72 that can range from 4 to 65535). If grater resolutions are required,
it is possible to opt for an exponential setting for 2 elevated to the nth power: the maximum value
is 18 (Pr72=18, that is 218, as the greatest value that can be set). The choice between these two
systems can be made through bit b70.0.
Bit b70.3 allows to select the type of signal used in the simulation generation.
- When the motor shaft position is used, the value is always read at the maximum
resolution: 220.
- When a pointed parameter is used, Pr71, the rating is read in its value, and therefore with
a resolution lower than 220. Therefore the reading must be considered as a part of a
revolution. However, if the value read by the pointed parameter is converted to the
maximum resolution, the significance of the reading does not change
A zero encoder trace is also generated at trace C.
Description
Par.
Pr72 Enc. Simulation pulses per revolution. If b70.0=0,
values range from 4 to 65535 pulses per revolution; if
b70.0=1 is the exponent and the maximum value that can
be entered is 18, Default=1024 is the number of pulses per
revolution used in the encoder simulation. The maximum
frequency is 400 kHz. [Fin=(number of encoder pulses) *
(rpm speed) / 60].
Motor internal position
Range Def. Res.
0÷
1024 1
+32767
2Pr72
b70.3
b70.0
Pointed parameter value
Pr71
Field
W
b170.8
Pr72
Resolution
max 220
b78.7
Pulses per rev.
Encoder simulator
X11
Description
Par.
b170.8 Encoder out simulation. (1) enc out simulation generation from
parameters scaled on a position Loop resolution.
Page 135 of 233
X10
Field
W
Def.
0
Parker Hannifin S.p.A S.B.C. Division
12.7.4 Motor cogging compensation
At lower speed levels, motor rotation can be “disturbed” by a cogging effect.
The drive can mitigate this effect. Before activating this function, go through the following steps:
- initial conditions:
o no alarm is active, Pr23=0;
o parameter Pr181=0;
o enable the drive;
o the motor rotation speed is ≤ 2rpm
- motor cogging mapping calculation:
o issue command b42.7=1
At this stage the drive automatically creates a table containing useful data to compensate
motor cogging.
The calculating function ends when bit b42.7 returns to“0”. At this point the motor can be
stopped.
In order to enable motor cogging compensation,, set bit b39.10=1.
N.B.
The table that the drive has generated during the calculation of cogging mapping is not
deleted when default parameters are loaded. In order to modify these data, repeat the
mapping calculation.
12.7.5 Multiturn absolute encoder phasing on “zero” machine
With a multiturn absolute encoder, initialize the absolute position read at power up on the motor
position by following the procedure below:
- position the mechanical axis on the desired machine point
- disable drive hardware b41.5=0
- set desired position in Pr69:68
- enter command b64.9 to perform the write procedure in the absolute encoder.
- After having entered a multiturn phasing command b64.9, bit b41.6, indicating “phasing ok”
is set to zero. Switch the electronics off and on again to be able to perform other axis enabling
procedures.
Par.
Description
Field Def.
0
b170.13 Multiturn position read. (1) if multiturn absolute position is read at R
power up
The range of absolute position depends of the encoder and it’s equal to:
number of turns
± 2 Pr169 •
2
Page 136 of 233
Parker Hannifin S.p.A S.B.C. Division
(✎)
12.7.6 Encoder CAN
If this function is enable, it is possible to generate and receive the “encoder like” signals by the
CAN line (there are two different CAN lines: CAN A and CAN B, which is qualified to
communicate with others Hi-drive only), which replaces quadratures signal.
The running is trasparent, respect to the traditional encoder signals: the CAN line must be
connected instead of quadratures signals, and must be considered that every encoder signal is
available every 1,024msec over the CAN (every 1,024msec per CAN A, every 5msec per CAN
B), and the signal has 4byte for data.
It is possible to have up to a maximum of three encoder signals, if the speed of the CAN is
1Mbs, and only one encoder signal if the speed is 500kbs.
Hi-drive needs some bit and parameters about the correct operation:
Par.
Pr260
Pr261
Pr326
Pr327
Pr328
Description
Encoder CAN A OUT baudrate.
Address of CAN A OUT.
Pointer of encoder CAN A OUT.
Address of CAN A IN.
Divisor factor of encoder IN. Reduction ratio
denominator of the input encoder counting by
CAN A.
Pr329
Multiplicative factor of encoder IN.
Reduction ratio numerator of the input encoder
counting by CAN A.
Pr331:330 Counting encoder CAN A IN.
Par.
b70.7
b70.8
b70.10
b79.5
Field
W
W
W
W
W
Range
0÷31
0÷31
0÷255
0÷255
0÷255
W
0÷255
1
1
R
±231
-
1
Description
Encoder CAN A IN function enabled. It activates at the
successive switching on after save the setting of the bit.
Encoder CAN A OUT function enabled. It activates at the
successive switching on after save the setting of the bit.
Encoder CAN OUT virtual enabled. Enable the encoder CAN
virtual through the parameter pointed from Pr326 or through the
motor position.
Initialization of CAN A OUT line.
Def. Ris.
1
1
1
1
1
1
1
1
Field
W
Def.
0
W
0
W
0
W
0
The encoder CAN A IN is active in input and accepts the CAN signal with address setting into
Pr327.
The output encoder CAN generates a encoder signal with the same address to CAN node
(Pr261).
Nel caso in cui l’indirizzo dell’encoder in ingresso (Pr327) venisse impostato pari al valore
dell’indirizzo in uscita (Pr261) l’asse che genera l’encoder CAN leggerà come ingresso il
segnale encoder CAN in uscita.
If the address of the input encoder (Pr327) is setting at the same value of the output address
(Pr261), the axe which generates the encoder CAN, reads input the encoder CAN output signal.
If the command b70.10 is enable, is possible to generate a encoder virtual signal, setting
b70.10=1, by the parameter pointed from Pr326.
Page 137 of 233
Parker Hannifin S.p.A S.B.C. Division
The bit b79.15 is watchdog bit for encoder CAN, and every time that an encoder message arrives
the status is 1.
The Encoder CAN B on Hi-drive has some bit and parameters about the correct operation:
Par.
Pr71
Pr262
Pr263
Description
Pointer of encoder CAN B OUT.
Encoder CAN B OUT baudrate.
Address of CAN B OUT.
Par.
b78.7
b170.8
Description
Encoder CAN B OUT enabled.
Enable the encoder CAN virtual through the parameter and it’s
possible to increase the resolution through an exponential scale.
Initialization of CAN B OUT line.
b79.6
Field
W
W
W
Range
0÷385
0÷31
0÷31
Def. Ris.
1
1
1
1
1
Field
W
W
Def.
0
0
W
0
The encoder CAN B signal is available every 5msec and it’s compatible with others Hi-drive
only.
Not compatible function with operating OPM140
Pointer of enc CAN B
Pr71
b170.8
CAN B
Baudrate enc CAN B
Enable enc CAN B
Resolution
max 220
Pr262
b78.7
Out CAN B
Pr263
Address enc CAN B
Motor position
CAN A
OUT
Pr261
Address enc CAN A
Pr326
Address enc CAN A
Pr327
Counter of enc CAN A
CAN A
Pr260
b70.8
b70.10
Pointer of
encoder CAN A
Baudrate enc CAN A
Enable enc CAN A OUT
CAN A
Multiplicative factor
enc CAN A
Pr329
Pr330:331
Pr328
Divisor factor enc
CAN A
Page 138 of 233
Enable enc CAN A IN
b70.7
CAN A
IN
Parker Hannifin S.p.A S.B.C. Division
(✎)
12.7.7 Ramp with “S” profile
With release software 10 or successive, it’s possible to use the positioner using the ramp with
“S” profile (b231.6), instead of linear profile (b231.6).
The ramp with “S” profile functions only with the positioner at 1msec of refresh (Pr181=122).
The bit b231.6 enables the ramp with “S” profile and during the execution isn’t possible realize
any variation at the variables of positioner, otherwise the execution of profile is compromised.
The value recommended, as ramp, is 1sec.
Description
Par.
b231.6 (0)Profile with linear ramp (1)Profile with “S” ramp. Through
the opm122, in the positioner section it’s possible to use the ramp
with “S” profile (b231.6=1), otherwise to the ramp with linear
profile (b231.6=0). See the following diagram.
Field
W
Select the profile of the ramp
Profile
running?
Yes
N.B.: the choice of the profile needs a restore of the
counter (target position as actual position), this is
necessary to attribute a specific sense to the quota .
NO
Disable the operative
mode:
b40.2=0
Set the ramp with “S”
profile:
b231.6=1
to set the ramp with linear profile:
b231.6=0
Wait that the positioner restores the
counters:
Pr201:200 = Pr213:212
(automatic function that is activated when
the ramp is set, and it uses the positioner)
NO
Pr201:200
=
Pr213:212
?
Yes
Profile
running?
Yes
NO
Enable the operative
mode:
b40.2=1
The positioner is ready to use
the ramp with “S” profile
Page 139 of 233
Def.
0
Parker Hannifin S.p.A S.B.C. Division
13 PROGRAMMING DIGITAL INPUTS AND OUTPUTS
13.1
The Pico-PLC
Never activate the saving of PLC instructions while the drive is enabled
The internal Pico-PLC is used to connect the external world (inputs/outputs) to the Hi-drive
parameter system. The PLC can be used to copy digital input to a binary parameter, to copy a
binary parameter to a digital output and to execute mathematical and Boolean operations. The
PLC program must be entered as a list of instructions either using the keypad or via serial link
(instruction list and ladder) using a PC and an interface program (MotionWiz). The default
parameter settings (b42.12) correspond to a program (default Pico PLC, see Appendix D). The
main features of the Pico-PLC are:
Program steps
scanning time
number of timers
number of instructions
stack depth
mathematical operations
256
6.144 ms
2
15
1
16 / 32 bits
Decimal PLC PARAMETERS
Par.
Pr92
Pr93
Pr96
Pr97
Pr98
Pr99
Pr100
Pr101
Description
First PLC timer. Every 6.144 ms, if Pr92 is not 0,
it is decreased; if it is = 0, b94.1 is set to 1.
Second PLC timer. Every 6.144 ms, if Pr93 is not
0, it is decreased; if it is = 0, b94.2 is set to 1.
User parameter. A parameter that can be stored by
the user (word).
User parameter. A parameter that can be stored by
the user (word).
User parameter. A parameter that can be stored by
the user (word).
User parameter. A parameter that can be stored by
the user (word).
CAN PLC 1 data block. A parameter that the user
can use to exchange data through the block sync of
the SBCCAN protocol via Bridge Profibus and
DeviceNet. This parameter is used to receive (see
sections about “SBCCAN” and “CANOPEN”).
CAN PLC 2 data block. A parameter that the user
can use to exchange data through the block sync of
the SBCCAN protocol via Bridge Profibus and
DeviceNet. This parameter is used to receive (see
sections about “SBCCAN” and “CANOPEN”).
Page 140 of 233
Field
W
W
RW
RW
RW
RW
R
R
Range
0÷
65635
0÷
65635
-32768
÷32767
-32768
÷32767
-32768
÷32767
-32768
÷32767
-32768
÷32767
-32768
÷32767
Def. Res.
0
0
0
1
0
1
0
1
0
1
0
1
0
1
Parker Hannifin S.p.A S.B.C. Division
Description
CAN PLC 3 data block. A parameter that the user
can use to exchange data through the block sync of
the SBCCAN protocol via Bridge Profibus and
DeviceNet. This parameter is used to receive (see
sections about “SBCCAN” and “CANOPEN”).
CAN PLC 4 data block. A parameter that the user
Pr103
can use to exchange data through the block sync of
the SBCCAN protocol via Bridge Profibus and
DeviceNet. This parameter is used to receive (see
sections about “SBCCAN” and “CANOPEN”).
CAN PLC 5 data block. A parameter that the user
Pr104
can use to exchange data through the block sync of
the SBCCAN protocol via Bridge Profibus and
DeviceNet. This parameter is used to receive (see
sections about “SBCCAN” and “CANOPEN”).
CAN PLC 6 data block. A parameter that the user
Pr105
can use to exchange data through the block sync of
the SBCCAN protocol via Bridge Profibus and
DeviceNet. This parameter is used to receive (see
sections about “SBCCAN” and “CANOPEN”).
CAN PLC 7 data block. A parameter that the user
Pr106
can use to exchange data through the block sync of
the SBCCAN protocol via Bridge Profibus and
DeviceNet. This parameter is used to receive (see
sections about “SBCCAN” and “CANOPEN”).
CAN PLC 8 data block. A parameter that the user
Pr107
can use to exchange data through the block sync of
the SBCCAN protocol via Bridge Profibus and
DeviceNet. This parameter is used to receive (see
sections about “SBCCAN” and “CANOPEN”).
Pr109:108 Spare data. Dedicated to CanOpen, this parameter
contains the message with the data to be sent.
User parameter. A parameter that can be stored by
Pr110
the user (word).
User parameter. A parameter that can be stored by
Pr111
the user (word).
User parameter. A parameter that can be stored by
Pr112
the user (word).
User parameter. A parameter that can be stored by
Pr113
the user (word).
User parameter. A parameter that can be stored by
Pr114
the user (word).
User parameter. A parameter that can be stored by
Pr115
the user (word).
User parameter. A parameter that can be stored by
Pr116
the user (word).
User parameter. A parameter that can be stored by
Pr117
the user (word).
User parameter. A parameter that can be stored by
Pr118
the user (word).
User parameter. A parameter that can be stored by
Pr119
the user (word).
Par.
Pr102
Page 141 of 233
Field
R
Range
-32768
÷32767
R
-32768
÷32767
0
1
W
-32768
÷32767
0
1
W
-32768
÷32767
0
1
W
-32768
÷32767
0
1
W
-32768
÷32767
0
1
W
-32768
÷32767
-32768
÷32767
-32768
÷32767
-32768
÷32767
-32768
÷32767
-32768
÷32767
-32768
÷32767
-32768
÷32767
-32768
÷32767
-32768
÷32767
-32768
÷32767
0
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Def. Res.
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Parker Hannifin S.p.A S.B.C. Division
Description
Field
Range Def. Res.
Constant value = -1. Double word. Adjustable RW
-32768
-1
1
parameter: the constant value can be modified and
÷32767
stored.
Constant value = 0. Double word. Adjustable RW
-32768
0
1
Pr122
parameter. the constant value can be modified and
÷32767
stored.
Constant value = 1. Double word. Adjustable RW
-32768
1
1
Pr123
parameter: the constant value can be modified and
÷32767
stored.
Constant value = 2. Double word. Adjustable RW
-32768
2
1
Pr124
parameter: the constant value can be modified and
÷32767
stored.
Constant value = 10. Double word. Adjustable RW
-32768
10
1
Pr125
parameter: the constant value can be modified and
÷32767
stored.
Constant value = 100. Double word. Adjustable RW
-32768 100 1
Pr126
parameter: the constant value can be modified and
÷32767
stored.
Constant value = 1000. Double word. Adjustable RW
-32768 1000 1
Pr127
parameter: the constant value can be modified and
÷32767
stored.
Constant value = 1024. Double word. Adjustable RW
-32768 1024 1
Pr128
parameter: the constant value can be modified and
÷32767
stored.
Constant value = 4096. Double word. Adjustable RW
-32768 4096 1
Pr129
parameter: the constant value can be modified and
÷32767
stored.
Note: parameters Pr121 to Pr129 cannot be combined in a double word (the PLC considers them
as 32bit with sign extension)
Par.
Pr121
Page 142 of 233
Parker Hannifin S.p.A S.B.C. Division
PLC binary parameters
Description
Par.
input 0.
b90.0
input 1.
b90.1
input 2.
b90.2
input 3.
b90.3
input 4.
b90.4
bit that can be stored. If X is greater than 5, the bit can be stored by
b90.x
the user. Available bits are b90.5 to b90.15.
output 0.
b91.0
output 1.
b91.1
Relay output. Controls the status of the relay output in terminal block
b91.2
X5.
Available bit. If Y is greater than 3, the bit is available to the user.
b91.y
Available bits are b91.4 to b91.15 and cannot be stored.
Forces a 32 bit double word formatted operation (self-resetting).
b94.0
When the unit is powered on, this is 0. If it is set to 1, the first
mathematical operation executed by the Pico-PLC is done by using
three double word type operands. After the execution of the operation,
b94.0 is automatically set to 0. If the parameters used are known as
being in double format (except parameters dedicated to operating
modes, i.e. Pr181 to Pr250), double word format is implicit. As for
operating mode parameters, double word format is implicit only in
parameters Pr200 to Pr229.
timer 1. (1) if timer 1 has expired. Equal to 1 if Pr92 = 0.
b94.1
timer 2. (1) if timer 2 has expired. Equal to 1 if Pr93 = 0.
b94.2
operation result <0. (1) if the result of the last algebric operation is <
b94.3
0.
algebric operation result =0. (1) if the result of the last algebric
b94.4
operation is = 0.
Page 143 of 233
Field
R
R
R
R
R
RW
Def.
0
0
0
0
0
0
W
W
W
0
0
0
W
0
W
0
R
R
R
0
0
0
R
0
Parker Hannifin S.p.A S.B.C. Division
PLC INSTRUCTIONS
Pa.y
Pa.y
Pa.y
LD
Pa.y
loads the y bit of the Pa parameter on the stack
LDN
Pa,y
loads the negated y bit of the Pa parameter on the stack
OUT
Pa,y
stack
sets the y bit of the Pa parameter to the value loaded on the
OUTN Pa,y
places the y bit of the Pa parameter to the value of stack
negating it
SET
RES
AND
if the stack = 1, the y bit of the Pa parameter is set to 1
if the stack = 1, the y bit of the Pa parameter is set to 0
if the bit loaded on the stack contains the result of the logical
AND operation between itself and the y bit of the Pa
parameter
the bit of the stack contains the result of the logical AND
operation between itself and the y bit of the negated Pa
parameter
the bit loaded on the stack contains the result of the logical
OR operation between itself and the y bit of the Pa parameter
the bit on the stack contains the result of the logical OR
operation between itself and the y bit of the negated Pa
parameter
if the bit on the stack = 1, the addition operation is executed
on the parameters in which: Pc = Pa + Pb
if the bit on the stack = 1, the subtraction operation is
executed on the parameters in which: Pc = Pa – Pb
if the bit on the stack = 1, the multiplication operation is
executed on the parameters in which: Pc = Pa ⋅ Pb
if the bit on the stack = 1, the division operation is executed
on the parameters in which: Pc = Pa / Pb
end of program
Pa.y
Pa.y
SET
Pa.y
RST
Pa.y
Pa.y
Pa,y
Pa,y
Pa,y
ANDN Pa,y
Pa.y
OR
Pa,y
ORN
Pa,y
ADD
Pa, Pb, Pc
SUB
Pa, Pb, Pc
MUL
Pa, Pb, Pc
DIV
DIV
Pa, Pb, Pc
END
END
Pa.y
Pa Pb Pc
ADD
Pa Pb Pc
SUB
Pa Pb Pc
MUL
Pa Pb Pc
FUNCTIONAL DESCRIPTION
The Pico-PLC program is scanned every 6.144 milliseconds. Based on this sampling, the inputs
are first read, then the two timers (Pr92 Pr93 b94.1 and b94.2) are updated, the user program is
scanned and finally outputs are updated. For this reason, both input reading and output setting
can vary by 6.144 ms with respect to the physical event. If the microprocessor is overloaded with
work (the operating mode is active, there are frequent serial requests and the PLC program is
long), it may take more than 6.144 milliseconds to scan the entire PLC program.
All the instructions of the Pico-PLC with the exception of the arithmetic instructions are single
bit instructions. The available stack has a depth of only one bit.
The LD (LDN) instruction loads the bit defined as an operand on the stack, while all the other
logical instructions work on the stack. Arithmetic instructions are executed only if the stack bit is
set to 1.
Page 144 of 233
Parker Hannifin S.p.A S.B.C. Division
For user convenience, truth tables of logical operations are given below.
AND logical operation
bit A
bit B
result
0
0
0
0
1
0
1
0
0
1
1
1
OR logical operation
bit A
bit B
result
0
0
0
0
1
1
1
0
1
1
1
1
The respective denied ANDN and ORN operations follow the same logic, except that the denied
value of the specified bit will be used.
12 bits from b90.4 to b90.15 are reserved on the PLC and can be stored. 14 additional bits from
b91.2 to b91.15 are available on the PLC but cannot be stored. They are always set to 0 when the
converter is powered on.
There are 14 word type user parameters, namely Pr95 to Pr99 and Pr110 to Pr119. They can be
stored and used as double word parameters.
Parameters Pr100 to PrP107 are dedicated to data exchange through the block sync of the SBC
CAN protocol (used to exchange data via Profibus Device Net bridges). The Pico-PLC includes
9 constants for arithmetic operations, that is Pr121 to Pr129. When the default parameters are
loaded, the constants have the values shown in the table and can be modified and stored with
different values. These parameters are already programmed to be considered as a double word.
When arithmetic instructions (ADD, SUB, MUL, DIV) are used, consider that the operators are
assumed to be words and are signed. If a double word operation is required, set b94.0 = 1 before
executing the operation. After the operation, the PLC will automatically set this bit to 0. Double
parameters are treated as double words, so that in an operation such as [ADD 121,122,212] the
result –1 will be written in the double word Pr212:213 without having to set b94.0=1 before the
operation. If Pr100=-1 and Pr101=0 the operation [ADD 100,122,212] will give as a result
Pr212:213=-1, while the same operation executed with b94.0=1 will assume Pr101 as the high
word of the double word Pr100:101 and the result will be Pr212:213=65535. If the parameters
used are known as being in double word format (except parameters dedicated to operating
modes, i.e. Pr 181 to Pr 250), double word format is implicit. As for operating mode parameters,
double word format is implicit only in parameters Pr200 to Pr229.
Example: ADD 100 122 212 in double word.
Pr100=-1; Pr101=0, in double word becomes Pr101:100, where Pr101 is the high word and
Pr100 is the low word (H=0:L=-1), that is = 65535.
Pr122=0; this is a 0 value constant considered in double word format (it will not be combined
with Pr123 to form a double word parameter).
The addition result is entered in Pr213:212=65535 (H=0:L=-1), where Pr213 takes the
significance of the high word in the double word (H), whereas Pr212 takes the value of the low
word (L).
Note that in mathematical operations with double words, only the low word is shown (L),
whereas the high word (H), which is the most significant, will appear in the following word.
At the end of each arithmetic operation, b94.3 is set to 0 in case of positive result and to 1 in case
of negative result; similarly, b94.4 is set to 1 when the result is zero and to 0 if the result is not
zero. These settings remain effective until the next arithmetic operation is executed (the
operation is executed only if the stack bit is one).
If the DIV operation is executed on a double word, the most significant part of the result contains
the remainder of the division, that is, if b94.0=1 and the operation [DIV 129,127,100] is
executed, the result will be Pr100=4 and Pr101=96.
Page 145 of 233
Parker Hannifin S.p.A S.B.C. Division
The user can make use of two timers, Pr92 and Pr93. To use the first timer load the time as a
number of samplings (6.144 ms) into PR92. For example, Pr92=100 is equal to 614 milliseconds.
Pr92 will automatically decrease as time goes by, and bit b94.1 will remain set to zero until the
times has not expired; when Pr92=0, b94.1 will be set to 1.
The same is true with the second timer using parameter Pr93 and bit b94.2. Pr92 Pr93 b94.1 and
b94.2 are updated only before the Pico-PLC program is scanned.
The maximum number of instructions is 256. Note that arithmetic operations take up the space of
two logical operations. If they are used, the maximum number of instructions accepted will be
decreased.
The PLC program must always end with the END instruction.
The Pico-PLC program can be edited via serial link or directly using the keypad. In this latter
case, in order to facilitate program changes, if you want to delete an instruction, go to the
instruction to be deleted and press the [+ or -] key. The type of instruction will be displayed. At
this point, hold the [S] key and press the [-] key: when both keys are released, the instruction will
be deleted. If you want to add an instruction after the In06, go to the next instruction In07 and
press the [+ or -] key. The type of instruction will be displayed. At this point, hold the [S] key
and press the [+] key. When both keys are released, an instruction will be entered. In this latter
case, make sure that the program does not exceed the maximum instruction number, otherwise
the last instructions will be lost. The Pico-PLC program can be edited or modified only when the
PLC is in stop (b39.13=0).
13.1.1 Pico-PLC default program
90.2
40.0
90.3
40.6
41.4
91.2
41.11
91.0
E ND
LD
OUT
90.2
40.0
Input 2 used for full scale
selection
LD
OUT
90.3
40.6
digital input 3 used for the stop
function
LD
OUT
41.4
91.2
digital relay output indicates
that the converter is OK
LD
OUT
41.11
91.0
digital output 0 indicates that
the thermal motor image is
active
END
Page 146 of 233
end of the program
Parker Hannifin S.p.A S.B.C. Division
13.2
Serial interface
The converter communication serial links are on asynchronous RS-485/RS-422 lines (port X8),
and on serial link RS-232 (port X4 – see par. “Hyper terminal connection” for a connection
diagram).
In serial link RS-232, speed can be set by parameter Pr256 (see table below). The address is
always set to 0, because only one converter can be connected.
As far as serial link RS-485/RS-422 is concerned, the same serial link can be connected to up to
32 converters, by setting a different serial address in each of them to parameter Pr259. It is also
possible to set the transmission speed parameter Pr258 (see table below).
The converters take control of the line only if they are queried by the master.
Pr 256 (RS232) – Pr258 (RS485-422) (decimal base)
0
1
2
3
5
6
7
8
b/s
600
1200
2400
4800
9600
19200
38400
57600
time-out (ms)
512
256
128
64
32
16
12
8
When the speed or the address have been modified, the link must be reinitialized . See
parameters below.
Par.
Pr256
Pr258
Pr259
Description
RS232 serial link speed code. This is the code
used to program the transmission speed.
RS422 serial link speed code. This is the code
used to program the transmission speed.
RS422 serial link address code.
Field
W
Range
0÷8
W
0÷31
6
1
W
0÷31
0
1
Description
Par.
b79.3 RS232 serial initializing command. Command to reinitialize serial
communication whenever the serial link speed value (Pr256) has been
modified. The serial link is in any case initialized when the converter is
powered on.
b79.4 RS485/422 serial initializing command. Command to reinitialize serial
communication whenever the speed or the address value (Pr258 and
Pr259) of the serial link have been modified. The serial link is in any case
initialized when the converter is powered on.
Page 147 of 233
Def. Res.
6
1
Field
W
Def.
0
W
0
Parker Hannifin S.p.A S.B.C. Division
13.3 Communication protocol
The column on the right in the table above shows the time-out value expressed in milliseconds
for each communication speed. This is the time within which the message must be sent,
beginning from the start of each message (STX). If a message is interrupted after this time, the
converter ignores what has been received and waits for the beginning of a new message.
The message consists of several consecutive bits. The format of the bits is the following:
1 start bit
8 bit of data defined by a following byte enclosed within square brackets
1 parity bit (even)
1 stop bit
The structure of the message is the following:
[STX] [CMD+ADDR] [BK+LUN] [PAR] [D0]... [Dn] [CHK]
where:
[STX] = $7E indicator of transmission start. If a field in the message except STX takes the value
$7E, this field is followed by a 0 ($00) so that it will not be interpreted as an [STX].
[CMD+ADDR] = command and address of the peripheral device, which is never zero. This data
is composed as follows: the first 5 bits (bits 0-4) define the address of the converter (from 0 to
31); the remaining 3 bits (bits 5-7) define the type of message sent, as described in the following
table:
CMD
1
2
3
4
5
6
7
bit 7
0
0
0
1
1
1
1
bit 6
0
1
1
0
0
1
1
bit 5
1
0
1
0
1
0
1
type of message
converter response
reading a Pico-PLC instruction
writing a Pico-PLC instruction
read parameter
writing a parameter
bit modification
writing a parameter to all the slaves
[BK+LUN] = the field LUN (first 3 bits) indicates the number of bytes of the sent data
(parameter or PLC instruction); it can take the following values: 1, 2 or 4. The value shall not
include 0 characters ($00) after the values corresponding to the transmission start character
($7E). Each parameter has a length of 2 bytes.
N.B.: Lengths of 2 and 4 are allowed only with even addresses .
The BK field covers the 5 most significant bits and represents the 5 most significant bits of the
Pico-PLC parameter address, table or instruction.
[PAR] = write/read address of the PLC parameter, table or instruction (8bit low in the address)
A parameter address is the number of the parameter* 2 on 13 bits: PAR represents the 8 less
significant bits of the address, whereas the 5 most significant bits will be written in the BK field.
The table used for the electronic cam is allocated in the parameter area at address 4096 to 6151
(the other addresses are reserved and will not be used). PLC instructions are mapped at address 0
to 511, instructions can be accessed through specific commands.
Page 148 of 233
Parker Hannifin S.p.A S.B.C. Division
It is also important to consider that the instruction address depends upon the length of the
previous instructions, varying between two and four bytes, (see PLC instruction table).
[D0]... [Dn] = data transmitted.
[CHK] = 256 module sum of all the fields, except [STX] (checksum).
Message types
[CMD1] = is the response message of the converter to a data request. The response message has
the following format:
[STX] [001+ADDR] [BK+LUN] [PAR] [D0]… [Dn] [CHK]
or it can be the confirmation message to a data write or data modify. In this case, the format is
the following:
[STX] [001+ADDR]
where ADDR always identifies which converter is answering.
[CMD2] = is the read message of an instruction in the PLC area. The message has the following
format:
[STX] [010+ADDR] [BK+LUN] [PAR] [CHK]
[CMD3] = is the write message to an instruction in the PLC area. The message has the following
format:
[STX] [011+ADDR] [BK+LUN] [PAR] [D0]… [Dn] [CHK]
[CMD4] = is the read message of a parameter. The message has the following format:
[STX] [100+ADDR] [BK+LUN] [PAR] [CHK]
[CMD5] = is the write message of a parameter. The message has the following format:
[STX] [101+ADDR] [BK+LUN] [PAR] [D0]… [Dn] [CHK]
[CMD6] = is the change bit message of a byte parameter. The message has the following format:
[STX] [110+ADDR] [BK+LUN] [PAR] [D0] [D1] [CHK]
In this case LUN=2 or else two bytes are sent for the data. The first byte is the mask containing
the 0s in the positions of the bits to be changed and 1s in the other positions, while the second
byte contains 1s in the positions of the bits that are to be set to 1 and 0s in the other positions.
The PAR address is that of the parameter (byte) where one or more bits are to be modified. If the
parameter is a word and the bit to be modified is one of the first 8 (b0...b7): PAR = the parameter
address; otherwise, if the bit to be modified is one of the upper 8 (b8...b15): PAR = the address
parameter + 1.
[CMD7] = is the write message of a parameter to all converters connected to the serial link. The
message has the following format:
[STX] [11100000] [BK+LUN] [PAR] [D0]… [Dn] [CHK]
The address of the peripheral device (ADDR) must be 0.
Notes:
-
The parameters that are displayed on the screen with decimals must be treated as integer
values. For example, a value of 978.5 is read and written as 9785.
- All values that are preceded by the $ symbol are to be understood as hex numbers.
Page 149 of 233
Parker Hannifin S.p.A S.B.C. Division
-
The value in square brackets identifies the base unit (byte) of the message.
All messages, to be valid, must be completed within a well-defined time-out which is a
function of speed, and must have correct parity and checksum.
- The converter responds to a request or to a data send only if the message has been
received correctly. In the case of an error in the message, no response is transmitted. The
only exception is message type 7 that is used to send data with a single message to all the
converters connected to the serial link.
Initializing and managing the serial link
RS-232 the converter is delivered with a 0 address and a speed of 19200 bps (Pr256=6). To
modify the configuration, first set the speed in Pr256, then initialize it by issuing the command
b79.3. Use command b42.15 to store the configuration.
RS-485/RS-422: the converter is delivered with a 0 address (Pr259=0) and a speed of 19200 bps
(Pr258=6). To modify the configuration, first set the speed in Pr258, then the serial address in
Pr259 and finally initialize it by issuing command b79.4. Use the command b42.15 to store the
configuration.
Accessing PLC instructions
Each Pico-PLC instruction takes 2 or 4 bytes whose format is the following:
Since the maximum length of each instruction in 2 bytes and the total area available in the PLC
is 512 bytes, the PLC program can have at the most 256 instructions.
PLC instructions
LD Pa.y
LDN Pa.y
OUT Pa.y
OUTN Pa.y
AND Pa.y
ANDN Pa.y
OR Pa.y
ORN Pa.y
ADD Pa, Pb, Pc
SUB Pa, Pb, Pc
MUL Pa, Pb, Pc
DIV Pa, Pb, Pc
SET Pa.y
RES Pa.y
END
code
0
1
2
3
4
5
6
7
8
9
10
11
12
13
15
length (in bytes)
2
2
2
2
2
2
2
2
4
4
4
4
2
2
2
The first 4 bits (b0..b3) of the first byte in each instruction contain the instruction code (see table
above).
In the first 8 logical instructions in the table (LD… ORN) as well as in SET and RES, the
remaining 4 bits of the first byte (b4..b7) contain the y value, while the second byte contains the
Pa value.
Page 150 of 233
Parker Hannifin S.p.A S.B.C. Division
In ADD, SUB, MUL and DIV mathematical instructions, the second byte contains the Pa value,
the third byte contains the Pb value, and the fourth byte contains the Pc value.
In the END instruction, the second byte is not used.
Instructions must follow each other beginning at address 0h and no byte can be left empty.
There is only one program and it is closed by an END instruction.
Serial link usage examples
In order to better understand how to implement the communication protocol via serial link, some
examples of each type of message are given below.
The values given are only indicative as examples.
First example: reading a 1 byte parameter
Suppose we want to read the value of parameter Pr25 (release software) and that its value is 43.
Suppose also that the converter serial address is 0. The following message will be sent:
[$7E][$80][$01][$32][$B3]
The converter responds with the following message:
[$7E][$20][$01][$32][$2B][$7E][$00]
Second example: reading a 2 byte parameter
Suppose we want to read the reference speed (Pr7) and that its value is 2000. Suppose also that
the converter serial address is 1. The following message will be sent:
[$7E][$81][$02][$0E][$91]
The converter responds with the following message:
[$7E][$21][$02][$0E][$D0][$07][$08]
Third example: reading a 1 byte parameter
Suppose we want to select operating mode 110 (Pr181). Suppose also that the converter serial
address is 0. The following message will be sent:
[$7E][$A0][$09][$6A][$6E][$81]
The converter responds with the following message:
[$7E][$23]
Fourth example: reading a 2 byte parameter
Suppose we want to set the rated current to 2.5 A (Pr33). Suppose also that the converter serial
address is 3. The following message will be sent:
[$7E][$A3][$02][$42][$19][$00][$00]
The converter responds with the following message:
[$7E][$23]
Page 151 of 233
Parker Hannifin S.p.A S.B.C. Division
Fifth example: setting a bit to 1
Suppose we want to send a command to save the PLC program (b42.14=1). Suppose also that the
converter serial is 0. The following message will be sent:
[$7E][$C0][$02][$2B][$BF][$40][$EC]
The converter responds with the following message:
[$7E][$20]
Sixth example: setting a bit to 0
Suppose we want to disable the converter via software (b40.9=0). Suppose also that the
converter serial address is 0. The following message will be sent :
[$7E][$C0][$02][$51][$FD][$00][$10]
The converter responds with the following message:
[$7E][$20]
Seventh example: reading a PLC instruction
Suppose we want to set the first PLC instruction as: LD 90.5. Suppose also that the converter
serial address is 0. The following message will be sent :
[$7E][$60][$02][$00][$50][$5A][$0C]
The converter responds with the following message:
[$7E][$20]
Page 152 of 233
Parker Hannifin S.p.A S.B.C. Division
14 CANBUS interface
A CANbus interface based on the physical layer ISO/DIS11898 is included on the SLVD-N
converter. The Data link layer is the full CAN version 2.0 part A (ID 11 bit) and a subset of the
application layer SBCCAN is used.
Are available two CAN protocols:
1. SBC CAN (standard)
2. CANopen DSP402 (requested, D version)
Note: to be expressly requested when placing your order: the drive may only have one protocol
at a time
14.1 SBC Can
The Can-bus on the converter has two operating modes.
The first operating mode is real time mode. This is used to establish a real time digital link
between the converters and a control unit that provides for path calculations and sends either the
position or the speed reference, or both, to the converters. The converters can thus trace the
motor actual position (Pb230.2=1). Real time mode is active when Pr181=140.
The second operating mode is communication mode. This is used to write or read all
parameters of each converter connected to the bus. This function is very useful when you want to
use the motion functions that have already been implemented in the base software of the
converter. The communication mode is automatically set when Pr181≠140.
The Can node address must be set on Pr261 with values ranging from 1 to 15.
The transmission speed is given by a combination of parameters Pr181 and Pr260 as shown in
the following table.
Pr260
0
1
2
3
4
5
6
7
Pr181=140
1 Mbps
Pr181≠140
125 kbps
1 Mbps
500 kbps
250 kbps
125 kbps
50 kbps
20 kbps
10 kbps
All changes in speed, address or function mode are activated using the b79.5 command or when
the converter is powered on again.
Par.
Pr260
Pr261
Description
BAUDRATE CAN. CAN line transmission speed
programming code.
CAN address. Indicates CAN address value.
Page 153 of 233
Field
W
W
Range Def. Res.
0÷32767
1
1
0÷127
1
1
Parker Hannifin S.p.A S.B.C. Division
Description
Par.
b79.5 CAN initializing command. Command to reinitialize CAN
communication whenever the speed or the address value (Pr260 and
Pr261) of the CAN line have been changed. This is in any case initialized
when the converter is powered on.
Field
W
Def.
0
14.1.1 Description of fields in real time mode
Cyclic message from master to slave converter
Cyclic data
Data length
Field Name
Contents
8/6/4 bytes
Speed Reference
Pr182 (16 bit)
Position Reference
Pr200:201(32 bit)
Command
Pr183 (16 bit)
Identifier
ID2 ID1
A2 A1
ID0
A0
X
X
X
X
X
ID10
0
ID9
0
ID8
0
ID7
0
ID6
0
ID5
1
ID4
1
ID3
A3
A0:A3 Converter slave address (Pr261), valid values 1..15.
Pr183 is used as a command and can be managed by the Pico-PLC.
Based on the length of the message, the data received are interpreted as follows.
Data length
8
6
4
Contents
Position reference (4 byte)
Position reference (4 byte)
Speed reference (2 byte)
Contents
Speed reference (2 byte)
Pr183 (2 byte)
Pr183 (2 byte)
Contents
Pr183 (2 byte)
Synchronism message from master to slave converter
Synchronism message
1 byte
Data length
Field Name
Contents
Sync
Sync type (8 bit)
Identifier
ID2 ID1
0
0
ID0
0
X
X
X
X
X
ID10
0
ID9
0
ID8
0
ID7
0
ID6
0
ID5
0
ID4
0
ID3
0
Type 0 synchronism (Sync = 0): each drive activates the speed and position references and saves
the current motor position. If b230.2=1, the drive responds with a “cyclic reply”.
Type 1 synchronism (Sync = 1): saves the current motor position. If b230.6=1, the drive
responds with a “cyclic reply”.
Page 154 of 233
Parker Hannifin S.p.A S.B.C. Division
Cyclic message from slave converter to master
Cyclic reply
Data length
Field Name
Data
6/7 byte
Motor Position
Pr202:203(32 bit)
Address
Pr261 (8bit)
Status
Pr184
Identifier
ID2
A2
ID1
A1
ID0
A0
X
X
X
X
X
ID10
0
ID9
0
ID8
0
ID7
1
ID6
0
ID5
1
ID4
0
ID3
A3
A0:A3 Converter slave address (Pr261), valid values 1..15.
Parameter Pr184 is used as a status, if b230.3 is = 0, all 16 bits are transmitted
if it is = 1, only the first 8 bits are transmitted.
Assuming that b230.0=1, the message will have a total length of 8 bytes and Pr184 will be made
of 16 bits whatever is the setting of b230.3. Assuming that b230.0=1, the message will contain
the following information:
Byte 0
Byte 7
7bit 6bit 5bit 4bit 3bit 2bit 1bit 0bit 7bit 6bit 5bit 4bit 3bit 2bit 1bit 0bit
MSB
LSB
In3 In2 In1 In0
Torque
Input
Multiple cyclic message from master to slave converter
MultiCyclic data
Data length
Field Name
Speed Reference0
Contents
Pr182 (16 bit)
2,4,6,8 byte
Speed Reference
Speed Reference 2
1
Pr182 (16 bit)
Pr182 (16 bit)
Speed Reference 3
Pr182 (16 bit)
Identifier
ID2 ID1
A1
0
ID0
A0
X
X
X
X
X
ID10
0
ID9
0
ID8
0
ID7
0
ID6
1
ID5
1
ID4
1
ID3
0
This type of message holds various information that are going to be addressed to multiple slave
converters. To identify the address logic used, see the following table that shows how the speed
reference values (Pr 182) are addressed to the various converters, based on the value of
A0:A1=group address.
A0:A1
0
1
2
3
Speed reference 0
Drive 1
Drive 5
Drive 9
Drive 13
Speed reference 1
Drive 2
Drive 6
Drive 10
Drive 14
Page 155 of 233
Speed reference 2
Drive 3
Drive 7
Drive 11
Drive 15
Speed reference 3
Drive 4
Drive 8
Drive 12
Parker Hannifin S.p.A S.B.C. Division
Multiple synchronism message from master to slave converter
MultiSynchronism message
Data length
Field Name
Contents
1,2,3,4 byte
Command 1
Command 2
Pr183 (8bit)
Pr183 (8bit)
Command 0
Pr183 (8bit)
Command 3
Pr183 (8bit)
Identifier
ID2 ID1
0
0
ID0
0
X
X
X
X
X
ID10
0
ID9
0
ID8
0
ID7
0
ID6
0
ID5
1
ID4
0
ID3
0
Each drive activates the speed references and stores the current motor position. If b230.2=1, the
drive responds with a “cyclic reply”.
To this end, consider that, being a message directed to multiple converters, you need to be able
to define which converters the “command” (first 8 bits of Pr183) is directed to. This information
is reported in the following table:
Drive
Drive1
Drive2
Drive3
Drive4
Drive5
Drive6
Drive7
Drive8
Drive9
Drive10
Drive11
Drive12
Drive13
Drive14
Drive15
Command0
YES
YES
Command 1
Command 2
Command 3
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
Thus we can conclude that each command is composed of 8 bits and is shared by multiple
converters. The user defines the bits within each command by programming the Pico-PLC of
each converter.
Page 156 of 233
Parker Hannifin S.p.A S.B.C. Division
Acyclic data write or parameter request message from master to slave converter
Acyclic data write or request
7 byte
Data length
Field Name
Contents
Cmd & Len
5 bit command and 3 bit length
Data Address
16 bit data address
Data
32 bit data
Identifier
ID2
A2
ID1
A1
ID0
A0
A0:A3
X
X
X
X
X
ID10
0
ID9
0
ID8
0
ID7
0
ID6
1
ID5
0
ID4
0
ID3
A3
Slave converter address (Pr261), valid values 1..15.
Cmd & Len Sub-field
Cmd [0..4]
Value
0
1
2
3
4
5-31
Len [5..7] 0-4
Significance
Read request
Write
SET bit Pr = Pr .OR. Data
RESET bit Pr = Pr.AND.(.NOT.Data)
TOGGLE bit Pr = Pr .XOR. Data
Not used
Number of significant bytes in the field
Data
Data Address
This is the address of the parameter involved in the operation (parameter number * 2).
The addresses of PLC instructions are ranging from 8192 to 8704.
The addresses of CAMMA tables are: (1) from 4096 to 4609, (2) from 4610 to 5123, (3) from
5124 to 5637, (4) from 5638 to 6151.
Data
When the parameter is written, it contains the value of the parameter itself..
If one or more bits are modified, it contains the mask of the bits to be modified. If case of a
parameter read request, the field has no significance. In case of PLC program writing, it contains
the instruction code (see Serial interface).
Acyclic response message to a parameter request from slave converter to master
Data reply
5 bytes
Data length
Field Name
Contents
Addr & Spare
Pr261
Data
32 bit reply data
Identifier
ID2 ID1
A2 A1
A0:A3
ID0
A0
X
X
X
X
X
ID10
0
ID9
0
ID8
0
Slave converter address (Pr261), valid values 1..15.
Page 157 of 233
ID7
1
ID6
1
ID5
0
ID4
0
ID3
A3
Parker Hannifin S.p.A S.B.C. Division
Broadcast write parameter message from master to slave converter
Broadcast data write
7 bytes
Data length
Field Name
Contents
Cmd & Len
5 bit command and 3 bit length
Data Address
16 bit data address
Data
32 bit data
Identifier
ID2 ID1
1
1
ID0
1
X
Cmd & Len Sub-field
Cmd [0..4]
X
X
Value
0
1
2
3
4
5-31
Len [5..7] 0-4
X
X
ID10
0
ID9
0
ID8
1
ID7
0
ID6
0
ID5
0
ID4
1
ID3
1
Significance
Not used
Write
SET bit Pr = Pr .OR. Data
RESET bit Pr = Pr.AND.(.NOT.Data)
TOGGLE bit Pr = Pr .XOR. Data
Not used
Number of significant bytes in the field
Data
Data Address
This is the address of the parameter involved in the operation (parameter number * 2). The
addresses of PLC instructions are in the range 8192 to 8704.
The addresses of CAMMA tables are: (1) from 4096 to 4609, (2) from 4610 to 5123, (3) from
5124 to 5637, (4) from 5638 to 6151.
Data
When the parameter is written, it contains the value of the parameter itself..
If one or more bits are modified, it contains the mask of the bits to be modified. In case of PLC
program writing, it contains the instruction code (see Serial interface).
Page 158 of 233
Parker Hannifin S.p.A S.B.C. Division
Alarm message from slave converter to master
Error
3 bytes
Data length
Field Name
Contents
Addr
Pr261
Error
Pr23
Identifier
ID2
A2
ID1
A1
ID0
A0
X
X
X
X
X
ID10
0
ID9
0
ID8
0
ID7
1
ID6
0
ID5
0
ID4
0
ID3
A3
A0:A Slave converter address (Pr261), valid values 1..15.
This type of message will be sent by the converter to the bus if the converter changes its alarm
status (alarm 0 = no alarm).
To evaluate the minimum sampling time, use the following formula:
Tcmin = ( Nr + Nt + 5 ) * 0.12
where: Tcmin is the minimum sampling time in milliseconds
Nr is the number of axes that receive the reference
Nt is the number of axes that transmit the feedback
The0.12 constant is referred to a speed of 1 Mbps
Note 1: In real time mode, you can use bit 230.15, which is set to 1 each time the synchronism
and multisynchronism message is received via SBCCAN.
Based on the above considerations, by simply adding a program to the Pico-PLC, you will be
able to ensure that the communication between master and slave via CAN-bus is active.
It is important to consider that, in this way, the communication via CAN-bus will be checked
every 6.144 [ms] or multiple thereof (minimum time required to complete the scanning of the
Pico-PLC program).
It should also be noted that both Pr184 (Status) and Pr183 (Command) must be managed in each
converter by an appropriate Pico-PLC program.
Note 2: if cyclic sync and data ≤6msec, the data can come immediately before and after the sync,
otherwise the sync shall be kept at least at 150 μsec from the data.
Note 3: in order to transmit multi-cyclic and cyclic data on the same CAN network, keep a
minimum distance of 150 μsec in between. The same principles should be applied to sync and
multisync messages.
The typical timing of the SBCCAN in real time mode is shown in the diagram on the next page.
Page 159 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
SBCCAN
Feedback from drive1
Feedback from drive2
T X reference
Sync
Feedback from drive3
Feedback from drive4
RX Feedback
Change Pr of drive X
2 1
Tx reference
>400µs
1
cyclic msg to drive1
cyclic msg to drive 2
1
cyclic msg to drive 3
1
cyclic msg to drive 4
TC
2
TX reference
Sync
RX Feedback
1 3
Require Pr of drive X
TC
3
Page 160 of 233
Drive X reply
Tx reference
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
14.1.2 Description of fields in communication mode
Data write message or parameter request from master to slave converter
Data write or request
7 bytes
Data length
Field Name
Contents
Cmd & Len
5 bit command and 3 bit length
Data Address
16 bit data address
Data
32 bit data
Identifier
ID2 ID1
A2 A1
ID0
A0
X
X
X
X
X
ID10
0
ID9
A4
ID8
0
ID7
0
ID6
1
ID5
0
ID4
0
ID3
A3
A0 A4 Hi-drive slave address (Pr261), valid values 1...31.
Cmd & Len Sub-field
Cmd [0..4]
Len [5..7]
Value
0
1
2
3
4
5-31
0-4
Significance
Read request
Write
SET bit Pr = Pr .OR. Data
RESET bit Pr = Pr.AND.(.NOT.Data)
TOGGLE bit Pr = Pr .XOR. Data
Not used
Number of significant bytes in the data field
Data
Data Address
This is the address of the parameter involved in the operation (parameter number * 2).
The PLC instructions have addresses in the range 8192 to 8704.
The addresses of CAMMA tables are: (1) from 4096 to 4609, (2) from 4610 to 5123, (3) from
5124 to 5637, (4) from 5638 to 6151.
Data
When the parameter is written, it contains the value of the parameter.
If one or more bits are modified, it contains the mask of the bits to be modified.
If case of a parameter read request, the field has no significance.
In the case of PLC program data writing, it contains the instruction code (see Serial Interface).
Page 161 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Response message to a parameter request from slave converter to master
Data reply
5 byte
Data length
Field Name
Contents
Addr & Spare
Pr261 (8bit)
Data
32 bit reply data
Identifier
ID2
A2
ID1
A1
ID0
A0
A0 A4
X
X
X
X
X
ID10
0
ID9
A4
ID8
0
ID7
1
ID6
1
ID5
0
ID4
0
ID3
A3
Slave converter address (Pr261), valid values 1..31.
Broadcast write parameter message from master to slave converter
Broadcast data write
7 byte
Data length
Field Name
Contents
Cmd & Len
5 bit command and 3 bit length
Data Address
16 bit data address
Data
32 bit data
Identifier
ID2 ID1
1
1
ID0
1
X
X
Cmd & Len Sub-field
Cmd [0..4]
Len [5..7]
X
X
Value
0
1
2
3
4
5
0-4
X
ID10
0
ID9
A4
ID8
1
ID7
0
ID6
0
ID5
0
ID4
1
ID3
1
Significance
Not used
Write
SET bit Pr = Pr .OR. Data
RESET bit Pr = Pr.AND.(.NOT.Data)
TOGGLE bit Pr = Pr .XOR. Data
Not used
Number of significant bytes in the data field
Data
Data Address
This is the address of the parameter involved in the operation (parameter number * 2). The
addresses of PLC instructions are ranging from 8192 to 8704.
The addresses of CAMMA tables are: (1) from 4096 to 4609, (2) from 4610 to 5123, (3) from
5124 to 5637, (4) from 5638 to 6151.
Data
When the parameter is written, it contains the value of the parameter.
If one or more bits are modified, it contains the mask of the bits to be modified.
In the case of PLC program data writing, it contains the instruction code (see Serial Interface).
Page 162 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Alarm message from slave converter to master
Error
3 bytes
Data length
Field Name
Contents
Addr
Pr261
Error
Pr23
Identifier
ID2 ID1
A2 A1
ID0
A0
A0 A4
X
X
X
X
X
ID10
0
ID9
A4
ID8
0
ID7
1
ID6
0
ID5
0
ID4
0
ID3
A3
Slave converter address (Pr261), valid values 1..31.
This type of message will be sent by the converter to the bus if the converter changes its alarm
status (alarm 0 = no alarm).
14.1.3 Description of extended message set #2
The extended message set 2 enables the exchange of memory areas between the master and the
converters both in communication and real-time modes. Data exchange is still synchronous. The
master transmits the data to all converters, which then save it in a temporary buffer. Then the
master transmits the synchronism message, and the drives, when they receive this message, will
copy the data blocks received from the temporary buffer to the parameter area and will reply to
the master with their own parameter sets.
Data send message from master to slave converter
Block send
8 byte
Data
64 bit of data
Data length
Field Name
Contents
Identifier
ID2
A2
ID1
A1
A0:A3
ID0
A0
X
X
X
X
X
ID10
1
Drive address valid values 1..15.
Page 163 of 233
ID9
0
ID8
0
ID7
0
ID6
0
ID5
0
ID4
1
ID3
A3
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Data synchronism message from master to slave converter
Block sync
0 byte
Data length
Field Name
Contents
No data
Identifier
ID2
0
ID1
0
ID0
0
X
X
X
X
X
ID10
1
ID9
0
ID8
0
ID7
0
ID6
0
ID5
0
ID4
0
ID3
0
The data received are saved from Pr100 to Pr103, and parameters Pr104 to Pr107 are transmitted
using the following message:
Reply from slave converter to master
Block reply
8 byte
Data
64 bit of data
Data length
Field Name
Contents
Identifier
ID2
A2
ID1
A1
A0:A3
ID0
A0
X
X
X
X
X
ID10
1
ID9
0
ID8
0
ID7
0
ID6
0
ID5
1
ID4
0
ID3
A3
Drive unit address valid values 1..15.
Note 1: just like in real time mode, you can use bit 79.14, which is set to1 each time block sync
is received via SBCCAN. Based on the above considerations, by simply adding a program to the
Pico-PLC, you will be able to ensure that the communication between master and slave via
CAN-bus is active.
It is important to consider that, in this way, the communication via CAN-bus will be checked
every 6.144 ms or multiple thereof (minimum time required to complete the scanning of the
Pico-PLC program).
Page 164 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
14.2 CANopen DSP402 (D version)
The Can node address must be set on Pr261 with values ranging from 1 to 127. The transmission
speed is given by the setting of parameter Pr260, as shown in the following table.
Pr260
0
1
2
3
4
5
6
7
0
125 kbps
1 Mbps
500 kbps
250 kbps
125 kbps
50 kbps
20 kbps
10 kbps
All changes in speed, address or function mode are activated using the b79.5 command or when
the converter is powered on again.
Description
Par.
Pr260 BAUDRATE CAN. CAN line transmission
programming code.
CAN
address. Indicates CAN address value.
Pr261
Field Range Def. Res.
speed W 0÷32767 1
1
W
0÷127
Description
Par.
b79.5 CAN initializing command. Command to reinitialize CAN
communication whenever the speed or the address value (Pr260 and
Pr261) of the CAN line have been changed. This is in any case initialized
when the converter is powered on.
1
Field
W
1
Def.
0
The following objects are available based on CANopen Pre-defined Connection Set:
Objects
NMT object
EMERGENCY object
SDO (tx) object
SDO (rx) object
NMT Error Control
(Node guarding)
Function code
0000
0001
1011
1100
COB-Ids
0x00
0x81-0xff
0x581-0x5ff
0x601-0x67f
Index
0x1014
0x1200
0x1200
1100
0x701-0x77f
0x100c- 0x100d
NMT object :
NMT state machine (DS301)
Page 165 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
NMT Error Control & Boot Up Protocol:
- Boot Up
- Node Guarding
EMERGENCY object :
Below is a description of emergency object implementation:
Emergency message from Drive to master
Emergency message
Data length
Field Name
Contents
Error code
16 bit code
8 byte
Drive address
8 bit address
Err. Reg
8 bit error
Data
32 bit reply data
Identifier
ID2 ID1
A2 A1
A0:A6
ID0
A0
X
X
X
X
X
ID10 ID9
0
0
ID8
0
ID7
1
ID6
A6
ID5
A5
ID4
A4
ID3
A3
Drive address (Pr261), valid values 1..127.
A warning message and a pop-up message are available for this object. The latter can be sent by
setting an appropriate command.
The alarm message is sent each time that the current alarm status (Pr23) changes, so that when a
new alarm occurs (or when the alarms are reset) the value 0x01 is sent to the field Err.Reg, and
the least significant byte of the Data field will contain the drive’s alarm code.
The alarm message transmission can be prevented by setting bit 78.0 to 1.
The Error Code field will contain a specific code based on the different drive alarm:
- Er01 (overvoltage) :
0x3210
- Er02 (undervoltage) :
0x3220
- Er03 (overcurrent) :
0x2340
- Er04 (speed fbk alarm) :
0x7310
- Er05 (motor over-temperature) :
0xff07
- Er06 (module over-temperature) : :
0x4310
- Er07 (aux trip 1) :
0xff00
- Er08 (aux trip 2) :
0xff01
- Er10 (checksum PLC) :
0x6310
- Er11 (checksum Parameters):
0x6310
- Er15 (default Parameters) :
0x6320
- Er16 (calibration alarm) :
0xff03
- Er17 (internal alarm type 1) :
0xff08
- Er20 (internal alarm type 2) :
0xff0a
- Er21 ( undervoltage 24VDC alarm) :
0x5112
- Er22 (ambient over-temperature alarm) :
0x4110
- Er23 (internal alarm type 3) :
0xff0c
- Er24 (braking transistor protection alarm) :
0xff0d
- Er25 (fbk speed loop initialization alarm) :
0xff0e
- Er26 (fbk pos loop initialization alarm) :
0xff0f
- Er28 (fbk pos loop alarm) :
0x7320
Page 166 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
When alarms are reset with b42.10, Error code field will be 0x0000.
A user pop-up message can be sent by setting command b79.12 to 1. In this case, the Error Code
field will be 0xFF09 and the Data field will contain the value in Pr108:109.
b 79.12 will be reset to 0 once the message has been sent.
SDO(tx/rx) object
In the CANopen implementation an SDO channel is available (standard cob-id) with a
changeable timeout value mapped at the index 0x2020 as Unsigned 16 with a default value of
5000 (1 unit 1.024 msec). Both standard guarding protocols are available , Node guarding and
heartbeat (the two cannot exist in the same time) Heartbeat is activated when a producer
heartbeat time is set different from 0. Three PDO channels PDO 1,2,4 from the predefined
standard connection set are available PDO 1 and 2 are serviced by a cyclic routine executed
every 2.048 msec and they are remappable (elements of 2 or 4 bytes can be mapped) the RTR is
allowed event time and inhibit time are active they can handle synchronous requests serviced
every 2.048 msec or they can be handled as event driven.
PDO 4 is the PDO channel used for strictly realtime operation as controlling motor trajectory or
position loop (the PDO is synchronous type 1) no RTR is allowed and a restricted set of
parameters can be mapped , in particular:
PDO 4 rx :
[0x6040]
control word
[0x60c1][1] position reference in counts
[0x60c1][2] velocity reference in counts/sec
[0x60c1][3] velocity reference in rpm
PDO 4 tx :
[0x6041]
status word
[0x6063]
position feedback in counts
[0x6064]
position feedback in counts (normally in user unit in this case as
well in counts)
[0x2060]
Word composed with digital input and aux analog input .
b0: In0
b1: In1
b2: In2
b3: In3
b4: enable
b5: In4
b6...b15 Analog input aux.
Life guarding protocol is implemented and can be activated writing life time factor and guard
time besides a missing guarding event ,life guarding protocol can be triggered by a missing sync
(if b79.8=1) or a bus-off condition. In any case state machine present state of ds301
communication can be changed according to what is set in the object 0x1029 ‘error behaviour’ (0
enter pre-operational, 1 no change, 2 stop).
Note NMT commands are handled every 1.024 msec, so subsequent commands should be sent to
the drive not closer than 1.204 msec including broadcast NMT commands.
Page 167 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
14.2.1 Dictionary object summary of ds301
[0x1000] : device type
[0x1001] : error register
[0x1005] : sync cob-id
[0x1006] : communication cycle period
[0x100c] : guard time
[0x100d] : life time factor
[0x1014] : Cob-Id Emergency object
[0x1017] : Producer heartbeat time
[0x1018] : Identity object
[0x1029] : Error behaviour
[0x1200] : SDO server parameters
//pdo
[0x1400] : PDO 1 rx communication parameters
[0x1401] : PDO 2 rx communication parameters
[0x1403] : PDO 4 rx communication parameters
[0x1600] : PDO 1 rx mapping parameters
[0x1601] : PDO 2 rx mapping parameters
[0x1603] : PDO 4 rx mapping parameters
[0x1800] : PDO 1 tx communication parameters
[0x1801] : PDO 2 tx communication parameters
[0x1803] : PDO 4 tx communication parameters
[0x1a00] : PDO 1 tx mapping parameters
[0x1a01] : PDO 2 tx mapping parameters
[0x1a03] : PDO 4 tx mapping parameters
//manufacturer
[0x2000] : parameters'array 0..254 read write access
[0x2001] : parameters'array 254..NR_PAR read write access
[0x2002] : parameters'array 0..254 set bit access
[0x2003] : parameters'array 254..NR_PAR set bit access
[0x2004] : parameters'array 0..254 reset bit access
[0x2005] : parameters'array 254..NR_PAR reset bit access
[0x2006] : pico-plc area first 254 instructions
[0x2007] : pico-plc area last 2 instructions
[0x2008] : CAM 1 table first 254 points read write access
[0x2009] : CAM 1 table first last 3 points read write access
[0x200a] : CAM 2 table first 254 points read write access
[0x200b] : CAM 2 table first last 3 points read write access
[0x200c] : CAM 3 table first 254 points read write access
[0x200d] : CAM 3 table first last 3 points read write access
[0x200e] : CAM 4 table first 254 points read write access
[0x200f] : CAM 4 table first last 3 points read write access
[0x2020] : SDO timeout
[0x2060] : digital and analog input
[0x2063] : encoder B counter
[0x2064] : encoder C counter
Page 168 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
[0x2065] : I° timer in msec.; it’s activated when the motor speed is equal to 0rpm (by the 7, 10 or
11 transition of the state machine), when the timer finishes, the bit b78.4 is set to 1, and it’s
possible to use it to management the motor brake.
[0x2066] : II° timer in msec.; it’s activated when the motor speed is equal to 0rpm (by the 7, 10
or 11 transition of the state machine), when the timer finishes, the drive is disabled. So the II°
timer [0x2066] must be longer of I° timer [0x2065].
7
10
Switch On
disabled
Motor
Brake
I° Timer(oggetto 0x 2065 )
11
Quick stop
active
Transition
II° Timer(oggetto 0x 2066 )
0 rpm
b70.4=1
Drive disabled
As a general rule, sub_index 0 of indexes 0x2000..0x200F represents the number of the
sub_indexes available, and the subsequent (1..N) sub_indexes represent the parameter number
concerned +1.
Sub_index 1 Æ Pr[0]
Sub_index 2 Æ Pr[1]
….
Sub_index n+1 Æ Pr[n]
Example of device memory access by SDO:
Write Pr80 to the drive:
You will need to write the object by SDO with index-sub_index 0x2000-0x51 (80+1).
If the number of bytes written is greater than two, the operation will also change the parameter
Pr81.
Read Pr60 from the drive:
You will need to read the object by SDO with index-sub_index 0x2000-0x3d (60+1). The value
returned will have a length of 4 bytes, the most significant of which will contain Pr61. If they are
not needed, they can simply be discarded.
Set bit 4 of Pr40:
You will need to write the object by SDO with index-sub_index 0x2002-0x29 (40+1) with the
value (0x0010) that represents in binary the bits involved in the operation, in our case bit 4.
Page 169 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Reset bits 4 and 5 of Pr40:
You will need to write the object by SDO with index-sub_index 0x2004-0x29 (40+1) with the
value (0x0030) that represents in binary the bits involved in the operation, in our case bits 4 and
5.
Write bytes 0 and 1 of the Pico-PLC area:
You will need to write the object by SDO with index-sub_index 0x2006-0x01 (0+1) with the
value corresponding to the operating code of the instruction to add. For example, the instruction
LD 90.0 requires the value 0x00 to be written in byte 0 and 0x5a in byte 1.
14.2.2 Dictionary object summary of dsp402
[0x6007] 'Abort connection option code': with the following available values
0: No action
1: Alarm (alarm MISSING_SYNC_TRIP (Er16) if sync is missing when b79.8=1 the
sync signal interval exceeds the 120% of the nominal sync cycle lasting time of index
0x1006 communication cycle period the regularity of sync signal is checked with a
resolution of 2.048 msec.
(If the node does not receive the guarding message before its lifetime an ABORT_CONN_TRIP
(Er13)) is generated.
2: disable voltage
3: quick stop
[0x6040] 'Control word':
[0x6041] 'Status word':
[0x605a] 'Quick stop option code': valid values 0,1,2,5,6
[0x605b] 'Shut down option code': valid values 0,1
[0x605c] 'Disable operation option code': valid values 0,1
[0x605e] 'Fault reaction option code': valid values 0,1,2.
[0x6060] 'Mode of operation': valid values 1 (om201), 6 (om200), 7 (om202), -1(om122),-2
(om121), -3 (om120)
[0x6061] 'Modes of operation display': see the previous.
[0x6063] 'position actual value (counts)': If read by mean of SDO or mapped on PDO 1 or 2
returns the value of position feedback in counts from pr[132:133] if mapped on PDO 4
returns the value of the position feedback at the sync signal.
[0x6064] 'position actual value (units)': If read by mean of SDO or mapped on PDO 1 or 2
returns the value in counts of position feedback pr[132:133] transformed in user units
by mean of position factor if mapped on PDO 4 returns the value of the position
feedback at the sync signal in counts (the algorithm of interpolated mode does not
support factor group).
[0x6065] 'Following error window': it is converted in counts by mean of position factor then set
in SERVO1 (pr[140:141]) the parameters is used to test following error. The
parameters of SERVO1 are changed by the firmware only if in remote mode.
[0x6066] 'Following error timeout': resolution of 1.024 msec per unit
[0x6067] 'Position window': in user units converted by mean of position factor and compared
with the motor position to check if target reached in profile position and interpolated
position modes.
Page 170 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
[0x6068] 'Position window time': resolution of 1.024 msec per unit
[0x607a] 'Target position': in user units converted by mean of position factor and used in profile
position mode (in this mode some elements of CAM tab 0 are used as spare memory
and so affected by changes).
[0x607c] 'Home offset': in position units converted by position factor
[0x6081] 'profile velocity': profile velocity in profile position mode(in counts/sec o RPM
depending on unit selection (standard or not) with b78.1)
[0x6083] 'profile acceleration': acceleration of profile in profile position mode (in counts/sec^2
or ms/kRPM depending on unit selection (standard or not) with b78.1)
[0x6084] 'profile deceleration': deceleration of profile in profile position mode (in counts/sec^2
or ms/kRPM depending on unit selection (standard or not) with b78.1)
[0x6085] 'quick stop deceleration': deceleration in quick stop action
[0x6086] 'Motion profile type': valid values 0.
[0x6093][1] 'Position factor': Numerator position factor
[0x6093][2] 'Position factor': Denominator position factor
[0x6094][1] 'Velocity encoder factor': Numerator velocity factor
[0x6094][2] 'Velocity encoder factor': Denominator velocity factor
[0x6097][1] 'Acceleration factor': Numerator acceleration factor
[0x6097][2] 'Acceleration factor': Denominator acceleration factor
[0x6098] 'Homing method': all standard values available.
[0x6099][1] 'Homing speeds': searching sensor velocity (in counts/sec or RPM depending on unit
selection (standard or not) with b78.1)
[0x6099][2] 'Homing speeds': searching index velocity (in counts/sec or RPM depending on unit
selection (standard or not) with b78.1)
[0x609a] 'Homing acceleration': acceleration homing (in counts/sec^2 or ms/kRPM depending
on unit selection (standard or not) with b78.1)
[0x60c0] 'Interpolation sub mode selection': valid values 0(linear interpolation),-1(cubic
interpolation with position and velocity) , -2 (cubic interpolation with position)
[0x60c1][1] 'Interpolation data record': INTEGER32 interpolator position reference
[0x60c1][2] 'Interpolation data record': INTEGER32 interpolator velocity reference in counts/sec
[0x60c1][3] 'Interpolation data record': INTEGER32 interpolator velocity reference in RPM
[0x6502] 'Supported drive modes': see (see 0x6060)
[0x6504] 'Drive Manufacturer': "Parker Hannifin div. SBC Italy"
[0x6505] 'http drive catalog address': "*** http://www.sbcelettronica.com ***
http://www.parker-eme.com ***"
Following modes of operation of DSP402 are implemented beside the device control state
machine:
Homing mode
Profile position mode
Interpolated position mode
Page 171 of 233
Hi-drive User Manual
Device Control state machine
Homing mode
Device Profile 402
Modes of operation
CAN node
Application layer and communication profile DS 301
Parker Hannifin S.p.A S.B.C. Division
Motor
Profile Position mode
Interpolated Position mode
Here by the schematic of device control with controlword e statusword
Control word
(6040h)
State machine
Internal events
Status word
(6041h)
Actions
Page 172 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Power disable
Fault
13
start
Fault reaction
active
0
14
Not ready to
switch On
Fault
1
15
Switch On
disabled
2
12
7
Ready to
Switch On
10
3
9
Power enable
6
8
Switched On
4
5
Operation enable
16
11
Quick stop active
If I2t current clamping is active bit 11 of the statusword rises. If b78.10=1 and in remote mode
the command bit of the static brake is driven by the bit 15 of the controlword.
If a fault on static brake occurs it is reported on bit7 (warning) of the statusword.
14.2.2.1 Object 6040h: Controlword
The controlword consist of bits for:
• the controlling of the state,
• the controlling of operating modes
• manufacturer specific options. OBJECT DESCRIPTION
Page 173 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
INDEX
Name
Object Code
Data Type
Category
6040h
Controlword
VAR
UNSIGNED16
Mandatory
ENTRY DESCRIPTION
Access
PDO Mapping
Value Range
Default Value
rw
Possible
UNSIGNED16
No
DATA DESCRIPTION The bits of the controlword are defined as follows:
15
11 10
9
8
7
6
4
3
2
1
0
Operation
Manufacturer
Fault
Enable
Quick Enable Switch
Reserved Halt
mode
specific
reset
operation stop
voltage on
specific
O
O
O
M
O
M
M
M
M
LSB
MSB
0 -Optional
M –Mandatory
BITS 0 – 3 AND 7:
Device control commands are triggered by the following bit patterns in the controlword:
Command
Shutdown
Switch on
Switch on
Disable
voltage
Quick stop
Disable
operation
Enable
operation
Fault reset
Fault
reset
0
0
0
Bit of the controlword
Enable
Enable
Quick stop
operation
voltage
X
1
1
0
1
1
1
1
1
Switch on
Transitions
0
1
1
2,6,8
3*
3**
0
X
X
0
X
7,9,10,12
0
X
0
1
X
7,10,11
0
0
1
1
1
5
0
1
1
1
1
4,16
X
X
X
X
15
Table 4: Device control commands (bits marked X are irrelevant, * ... In the state
SWITCHED ON the drive executes the functionality of this state., ** ... It exists no
functionality in the state SWITCHED ON. The drive does not do any in this state.)
BITS 4, 5, 6 AND 8:
These bits are operation mode specific. The description is situated in the chapter of the special
mode. The following table gives an overview:
Page 174 of 233
Parker Hannifin S.p.A S.B.C. Division
Bit
4
5
6
8
Hi-drive User Manual
Operation mode
Profile velocity mode
reserved
reserved
reserved
Halt
Velocity mode
rfg enable
rfg unlock
rfg use ref
Halt
Profile torque mode
reserved
reserved
reserved
Halt
Table 5: Mode specific bits in the controlword
BITS 9, 10:
These bits are reserved for further use. They are inactive by setting to zero. If they have no
special function, they must be set to zero.
BITS 11, 12, 13, 14 AND 15:
These bits are manufacturer specific.
14.2.2.2 Object 6041h: Statusword
The statusword indicates the current state of the drive. No bits are latched. The statusword
consist of bits for:
• the current state of the drive,
• the operating state of the mode and
• manufacturer specific options.
OBJECT DESCRIPTION
INDEX
Name
Object Code
Data Type
Category
6041h
Statusword
VAR
UNSIGNED16
Mandatory
ENTRY DESCRIPTION
Access
PDO Mapping
Value Range
Default Value
ro
Possible
UNSIGNED16
No
Page 175 of 233
Parker Hannifin S.p.A S.B.C. Division
Bit
0
1
2
3
4
5
6
7
8
9
10
11
12 - 13
14 - 15
Hi-drive User Manual
Description
Ready to switch on
Switched on
Operation enabled
Fault
Voltage enabled
Quick stop
Switch on disabled
Warning
Manufacturer specific
Remote
Target reached
Internal limit active
Operation mode specific
Manufacturer specific
M /O
M
M
M
M
M
M
M
O
O
M
M
M
O
O
BITS 0 – 3, 5 AND 6:
The following bits indicate the status of the device:
Value (binary)
State
xxxx xxxx x0xx 0000
Not ready to switch on
xxxx xxxx x1xx 0000
Switch on disabled
xxxx xxxx x01x 0001
Ready to switch on
xxxx xxxx x01x 0011
Switched on
xxxx xxxx x01x 0111
Operation enabled
xxxx xxxx x00x 0111
Quick stop active
xxxx xxxx x0xx 1111
Fault reaction active
xxxx xxxx x0xx 1000
Fault
Table 7: Device state bits (x ... irrelevant for this state)
BIT 4: VOLTAGE ENABLED
High voltage is applied to the drive when this bit is set to 1.
BIT 5: QUICK STOP
When reset, this bit indicates that the drive is reacting on a quick stop request. Bits 0, 1 and 2 of
the statusword must be set to 1 to indicate that the drive is capable to regenerate. The setting of
the other bits indicates the status of the drive (e.g. the drive is performing a quick stop as result
of a reaction to a non-fatal fault. The fault bit is set as well as bits 0, 1 and 2).
BIT 7: WARNING
A drive warning is present if bit 7 is set. The cause means no error but a state that has to be
mentioned, e.g. temperature limit, job refused. The status of the drive does not change. The cause
of this warning may be found by reading the fault code parameter. The bit is set and reset by the
device.
Page 176 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
BIT 8:
This bit may be used by a drive manufacturer to implement any manufacturer specific
functionality.
BIT 9: REMOTE
If bit 9 is set, then parameters may be modified via the CAN-network, and the drive executes the
content of a command message. If the bit remote is reset, then the drive is in local mode and will
not execute the command message. The drive may transmit messages containing valid actual
values like a position actual value, depending on the actual drive configuration. The drive will
accept accesses via SDO in local mode.
BIT 10: TARGET REACHED
If bit 10 is set by the drive, then a set-point has been reached. The set-point is dependent on the
operating mode. The description is situated in the chapter of the special mode. The change of a
target value by software alters this bit.
If quick stop option code is 5, 6, 7 or 8, this bit must be set, when the quick stop operation is
finished and the drive is halted.
If halt occurred and the drive has halted then this bit is set too.
BIT 11: INTERNAL LIMIT ACTIVE
This bit set by the drive indicates, that an internal limitation is active (e.g. position range limit).
BIT 12 AND 13:
These bits are operation mode specific. The description is situated in the chapter of the special
mode The following table gives an overview:
Bit
vl
12
reserved
13
reserved
pp
Set-point
acknowledge
Following error
Operation mode
pv
tq
Speed
reserved
Max slippage
error
reserved
hm
Homing
attained
ip
ip mode
active
Homing error
reserved
Table 8: Mode specific bits in the statusword
BIT 14 AND 15:
These bits may be used by a drive manufacturer to implement any manufacturer specific
functionality.
14.2.2.3 Object 605Bh: Shutdown option code
The parameter shutdown option code determines what action should be taken if there is a
transition OPERATION ENABLE READY TO SWITCH ON.
OBJECT DESCRIPTION
Page 177 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
INDEX
605Bh
Name
Shutdown option code
Object Code
VAR
Data Type
INTEGER16
Category
Optional
ENTRY DESCRIPTION
Access
PDO Mapping
Value Range
Default Value
rw
No
INTEGER16
0
DATA DESCRIPTION
Value
-32768 ... –1
0
1
2 ... 32767
Description
manufacturer specific
Disable drive function
Slow down with slow down ramp; disable of the drive function
reserved
14.2.2.4 Object 605Ch: Disable operation option code
The parameter disable operation option code determines what action should be taken if there is a
transition OPERATION ENABLE SWITCHED ON. OBJECT DESCRIPTION
INDEX
Name
Object Code
Data Type
Category
605Ch
Disable operation option code
VAR
INTEGER16
Optional
ENTRY DESCRIPTION
Access
PDO Mapping
Value Range
Default Value
rw
No
INTEGER16
1
DATA DESCRIPTION
Value
-32768 ... -1
0
1
2 ... 32767
Description
manufacturer specific
Disable drive function
Slow down with slow down ramp and then disabling of the drive function
reserved
Page 178 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
14.2.2.5 Object 605Ah: Quick stop option code
The parameter quick stop option code determines what action should be taken if the Quick Stop
Function is executed.
OBJECT DESCRIPTION ENTRY DESCRIPTION
INDEX
Name
Object Code
Data Type
Category
605Ah
Quick stop option code
VAR
INTEGER16
Optional
Access
PDO Mapping
Value Range
Default Value
rw
No
INTEGER16
2
DATA DESCRIPTION
Value Description
0
disable drive function
1
slow down on slow down ramp
2
slow down on quick stop ramp
5
slow down on slow down ramp and stay in QUICK STOP
6
slow down on quick stop ramp and stay in QUICK STOP
14.2.2.6 Object 605Eh: Fault reaction option code
The parameter Fault reaction option code determines what action should be taken if a fault
occurs.
OBJECT DESCRIPTION
INDEX
Name
Object Code
Data Type
Category
605Eh
Fault reaction option code
VAR
INTEGER16
Optional
ENTRY DESCRIPTION
Access
PDO Mapping
Value Range
Default Value
rw
No
INTEGER16
2
Page 179 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
DATA DESCRIPTION
Value
-32768 ... -1
0
1
2
Description
manufacturer Specific
disable drive, motor is free to rotate
slow down on slow down ramp
slow down on quick stop ramp
14.2.2.7 Object 6060h: Modes of operation
The parameter modes of operation switches the actually choosen operation mode.
OBJECT DESCRIPTION
INDEX
Name
Object Code
Data Type
Category
6060h
Modes of operation
VAR
INTEGER8
Mandatory
ENTRY
DESCRIPTION
Access
PDO Mapping
Value Range
Default Value
rw
Possible
INTEGER8
No
DATA
DESCRIPTION
Value
1
6
7
Description
Profile Position Mode
Homing Mode
Interpolated Position Mode
NOTE A read of modes of operation shows only the value of modes of operation. The actual
mode of the drive is reflected in the object modes of operation display. It may be changed by
writing to modes of operation.
14.2.2.8 Object 6061h: Modes of operation display
The modes of operation display shows the current mode of operation. The meaning of the
returned value corresponds to that of the modes of operation option code (index 6060h).
OBJECT DESCRIPTION
Page 180 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
INDEX
Name
Object Code
Data Type
Category
6061h
Modes of operation display
VAR
INTEGER8
Mandatory
ENTRY
DESCRIPTION
Access
PDO Mapping
Value Range
Default Value
ro
Possible
INTEGER8
No
DATA DESCRIPTION Same as for object 6060h modes of operation.
NOTE The actual mode is reflected in the modes of operation display (index 6061h), and not in
the modes of operation (index 6060h).
14.2.3 Functional description
14.2.3.1 Modes of operation function
The device behaviour depends on the activated modes of operation.
It is possible to implement different device modes. Since it is not possible to operate the modes
in parallel, the user is able to activate the required function by selecting a mode of operation. An
example of exclusive functions are those for position and torque control, which can only control
one variable at any one time. The variables can perform at most a limited function. Such hybrids
are regarded as the particular characteristics of a mode of operation. Position control operation
and encoder profile support can be active at the same time, for example. Consequently encoder
profile support is not regarded as a mode of operation.
Modes of
operation
(6060h)
Velocity mode
Operation mode
function
Profile velocity mode
Profile torque mode
Modes of
operation display
(6061h)
Page 181 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
14.2.4 Homing mode
In homing mode all the standard methods are available the index is referred to the feedback C
encoder input track Z, it is also possible to refer the index to the absolute (in the shaft revolution)
position of zero of the position feedback (resolver, SinCos absolute etc) setting the homing
method to the same absolute value as for track Z indexing but negative .In this case the
presetting of the position counters on the index is completed without axis movement.
For homing procedures 3 digital inputs are used
IN2 : home switch
IN3 : Left limit switch
IN4 : Right limit switch
The active level of the 3 inputs can be inverted by mean of a bit mask mapped at index 0x2021
as U16 where bit 2,3,4 are processed by a XOR operation with the logical status of IN2, IN3 and
IN4.
14.2.4.1 General information
This chapter describes the method by which a drive seeks the home position (also called, the
datum, reference point or zero point). There are various methods of achieving this using limit
switches at the ends of travel or a home switch (zero point switch) in mid-travel, most of the
methods also use the index (zero) pulse train from an incremental encoder.
Control word
Status word
Homing option code
Homing speed
Homing
Position demand value
Homing acceleration
Home offset
Figure 20: The homing function
14.2.4.2 Input data description
The user can specify the speeds, acceleration and the method of homing. There is a further object
home offset which allows the user to displace zero in the user’s coordinate system from the home
position.
There are two homing speeds; in a typical cycle the faster speed is used to find the home switch
and the slower speed is used to find the index pulse. The manufacturer is allowed some
discretion in the use of these speeds as the response to the signals may be dependent upon the
hardware used.
Page 182 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
14.2.4.3 Output data description
There is no output data except for those bits in the statusword which return the status or result of
the homing process and the demand to the position control loops.
14.2.4.4 Internal states
The homing mode will control by the bits of the controlword and statusword.
14.2.4.4.1 Controlword of homing mode
15 9
8 7 6 5
4
3 0
Halt
reserved Homing operation start
MSB
LSB
Name
Table
Value
0
0→1
Homing operation start
1
1→0
0
Halt
1
11:
Homing
mode
Description
Homing mode inactive
Start homing mode
Homing mode active
Interrupt homing mode
Execute the instruction of bit 4
Stop axle with homing acceleration
bits
of
the
controlword
14.2.4.4.2 Statusword of homing mode
15 14
13
12
11
10
9
Homing error Homing attained
Target reached
MSB
0
LSB
Name
Value
Target reached
0
1
Homing
0
attained
1
Homing error
0
Description
Halt = 0: Home position not reached Halt = 1: Axle decelerates
Halt = 0: Home position reached Halt = 1: Axle has velocity 0
Homing mode not yet completed
Homing mode carried out successfully
No homing error
Homing error occurred; Homing mode carried out not successfully;
1
The error cause is found by reading the error code
Table 12: Homing mode bits of the statusword
Page 183 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
14.2.4.5 Object dictionary entries
14.2.4.5.1 Objects defined in this chapter
Index
607Ch
6098h
6099h
609Ah
Object
VAR
VAR
ARRAY
VAR
14.2.4.5.2 Objects
Name
Home offset
Homing method
Homing speeds
Homing acceleration
defined
Type
INTEGER32
INTEGER8
UNSIGNED32
UNSIGNED32
in
Index Object Name
6040h VAR
Controlword
6041h VAR
Statusword
Attr.
rw
rw
rw
rw
M/O
O
M
M
O
other
chapters
Type
Chapter
UNSIGNED16 dc
UNSIGNED16 dc
14.2.4.6 Object description
14.2.4.6.1 Object 607Ch: Home offset
The home offset object is the difference between the zero position for the application and the
machine home position (found during homing), it is measured in position units. During homing
the machine home position is found and once the homing is completed the zero position is offset
from the home position by adding the home offset to the home position. All subsequent absolute
moves shall be taken relative to this new zero position. This is illustrated in the following
diagram.
Home
position
Zero
position
HOME OFFSET
Figure 21: Home offset If the home offset is not implemented then it shall be zero.
OBJECT DESCRIPTION
INDEX
Name
Object Code
Data Type
Category
607Ch
Home offset
VAR
INTEGER32
Optional
ENTRY DESCRIPTION
Access
rw
Page 184 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
PDO Mapping Possible
Value Range
INTEGER32
Default Value 0
14.2.4.6.2 Object 6098h: Homing method
The homing method object determines the method that will be used during homing. OBJECT
DESCRIPTION
INDEX
Name
Object Code
Data Type
Category
6098h
Homing method
VAR
INTEGER8
Conditional;
Mandatory, if hm supported
ENTRY DESCRIPTION
Access
PDO Mapping
Value Range
Default Value
rw
Possible
INTEGER8
0
DATA DESCRIPTION
Value
-128 .. -1
0
1..35
36 .. 127
Description
manufacturer specific
No homing operation required
Methods 1 to 35 (see the functional description)
reserved
14.2.4.6.3 Object 6099h: Homing speeds
This entry in the object dictionary defines the speeds used during homing and is given velocity
units. OBJECT DESCRIPTION.
INDEX
Name
Object Code
Data Type
Category
6099h
Homing speeds
ARRAY
UNSIGNED32
Mandatory, if hm supported
Page 185 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
ENTRY DESCRIPTION
Sub-Index
Description
Entry Category
Access
PDO Mapping
Value Range
Default Value
Sub-Index
Description
Entry Category
Access
PDO Mapping
Value Range
Default Value
Sub-Index
Description
Entry Category
Access
PDO Mapping
Value Range
Default Value
0
number of entries
Mandatory
ro
No
2
2
1
Speed during search for switch
Mandatory
rw
Possible
UNSIGNED32
0
2
Speed during search for zero
Mandatory
rw
Possible
UNSIGNED32
0
14.2.4.6.4 Object 609Ah: Homing acceleration
The homing acceleration establishes the acceleration to be used for all accelerations and
decelerations with the standard homing modes and is given in acceleration units.
OBJECT DESCRIPTION
INDEX
Name
Object Code
Data Type
Category
609Ah
Homing acceleration
VAR
UNSIGNED32
Optional
ENTRY DESCRIPTION
Access
PDO Mapping
Value Range
Default Value
rw
Possible
UNSIGNED32
No
Page 186 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
14.2.4.7 Functional description
By choosing a method of homing by writing a value to homing method will clearly establish
ƒ the homing signal (positive limit switch, negative limit switch, home switch)
ƒ the direction of actuation and where appropriate
ƒ the position of the index pulse(*).
The home position and the zero position are offset by the home offset, see the definition of home
offset for how this offset is used.
Various homing positions are illustrated in the following diagrams. An encircled number
indicates the code for selection of this homing position. The direction of movement is also
indicated. Further homing methods may be defined by the manufacturer using the negative
values of homing method.
There are four sources of homing signal available, these are the negative and positive limit
switches, the home switch and the index pulse from an encoder.
In the diagrams of homing sequences shown below, the encoder count increases as the axle's
position moves to the right, in other words the left is the minimum position and the right is the
maximum position.
For the operation of positioning drives, an exact knowledge of the absolute position is normally
required. Since for cost reasons, drives often do not have an absolute encoder, a homing
operation is necessary. There are several, application-specific methods. The homing method is
used for selection.
The exact sequence of the homing operation is clearly described by the method. In some
circumstances, a device has several methods to choose from, using the homing method.
(*) with feedback from resolver, it’s necessary to set the object 0x6060 with negative sign. In
this case, the homing function is concluded when is out of home sensor, and the actual position
of resolver becomes the home position.
14.2.4.8 Homing methods
The following sub-sections describe the details of how each of the homing modes shall function.
14.2.4.8.1 Method 1: Homing on the negative limit switch and index pulse
Using this method the initial direction of movement is leftward if the negative limit switch is
inactive (here shown as low). The home position is at the first index pulse to the right of the
position where the negative limit switch becomes inactive.
(1)
Index Pulse Negative Limit Switch
Figure 22: Homing on the negative limit switch and index pulse
Page 187 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
14.2.4.8.2 Method 2: Homing on the positive limit switch and index pulse
Using this method the initial direction of movement is rightward if the positive limit switch is
inactive (here shown as low). The position of home is at the first index pulse to the left of the
position where the positive limit switch becomes inactive.
(2)
Index pulse
Positive Limit Switch
Figure 23: Homing on the positive limit switch and index pulse
14.2.4.8.3 Methods 3 and 4: Homing on the positive home switch and index pul.
Using methods 3 or 4 the initial direction of movement is dependent on the state of the home
switch. The home position is at the index pulse to either to the left or the right of the point where
the home switch changes state. If the initial position is sited so that the direction of movement
must reverse during homing, the point at which the reversal takes place is anywhere after a
change of state of the home switch.
(3)
(3)
(4)
(4)
Index pulse
Home switch
Figure 24: Homing on the positive home switch and index pulse
Page 188 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
14.2.4.8.4 Methods 5 and 6: Homing on the negative home switch and index pul.
Using methods 5 or 6 the initial direction of movement is dependent on the state of the home
switch. The home position is at the index pulse to either to the left or the right of the point where
the home switch changes state. If the initial position is sited so that the direction of movement
must reverse during homing, the point at which the reversal takes place is anywhere after a
change of state of the home switch.
(5)
(5)
(6)
(6)
Index pulse
Home switch
Figure 25: Homing on the negative home switch and index pulse
14.2.4.8.5 Methods 7 to 14: Homing on the home switch and index pulse
These methods use a home switch which is active over only portion of the travel, in effect the
switch has a ‘momentary’ action as the axle's position sweeps past the switch.
Using methods 7 to 10 the initial direction of movement is to the right, and using methods 11 to
14 the initial direction of movement is to the left except if the home switch is active at the start
of the motion. In this case the initial direction of motion is Dependent on the edge being sought.
The home position is at the index pulse on either side of the rising or falling edges of the home
switch, as shown in the following two diagrams. If the initial direction of movement leads away
from the home switch, the drive must reverse on encountering the relevant limit switch.
Page 189 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
(8)
(10)
(9)
(7)
(7)
(10)
(8)
(7)
(9)
(9)
(8)
(10)
Index pulse
Home switch
Positive limit switch
Figure 26: Homing on the home switch and index pulse - positive initial move
(14)
(12)
(13)
(11)
(14)
(11)
(13)
(12)
(13)
(14)
(11)
(12)
Index pulse
Home switch
Negative
limit switch
Figure 27: Homing on the home switch and index pulse - negative initial move
14.2.4.8.6 Methods 15 and 16: Reserved
These methods are reserved for future expansion of the homing mode.
Page 190 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
14.2.4.8.7 Methods 17 to 30: Homing without an index pulse
These methods are similar to methods 1 to 14 except that the home position is not dependent on
the index pulse but only dependent on the relevant home or limit switch transitions. For example
methods 19 and 20 are similar to methods 3 and 4 as shown in the following diagram.
(19)
(19)
(20)
(20)
Home switch
Figure 28: Homing on the positive home switch
14.2.4.8.8 Methods 31 and 32: Reserved
These methods are reserved for future expansion of the homing mode.
14.2.4.8.9 Methods 33 to 34: Homing on the index pulse
Using methods 33 or 34 the direction of homing is negative or positive respectively. The home
position is at the index pulse found in the selected direction.
(33)
(34)
Index pulse
Figure 29: Homing on the index pulse
14.2.4.8.10 Method 35: Homing on the current position
In method 35 the current position is taken to be the home position.
Page 191 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
14.2.5 Profile position mode
In profile position mode the buffer of targets allowed is 2 elemets long one for the profile in
execution the other for the next, the motion profile type only valid value is 0 (trapezoidal profile
with linear ramp).
14.2.5.1 Internal states
The profile position mode will control by the bits of the controlword and statusword.
Index
607Ah
6081h
6083h
6084h
6085h
6086h
Object
VAR
VAR
VAR
VAR
VAR
VAR
Name
Target position
Profile velocity
Profile acceleration
Profile deceleration
Quick stop deceleration
Motion profile type
Type
INTEGER32
UNSIGNED32
UNSIGNED32
UNSIGNED32
UNSIGNED32
INTEGER16
Attr.
rw
rw
rw
rw
rw
rw
M/O
M
M
M
O
O
M
14.2.5.1.1 Controlword of profile position mode
15 9
8
7 6
5
4
3 0
Halt
abs / rel Change set immediately New set-point
MSB
LSB
Name
Value
Description
New
set0
Does not assume target position
point
1
Assume target position
Finish the actual positioning and then start the next
Change set
0
positioning
immediately
Interrupt the actual positioning and start the next
1
positioning
0
Target position is an absolute value
abs / rel
1
Target position is a relative value
Halt
0
Execute positioning
Stop axle with profile deceleration (if not supported with
1
profile acceleration)
Table 9: Profile position mode bits of the controlword
14.2.5.1.2 Statusword of profile position mode
15 14 13
12
11 10
9 0
Following error Set-point acknowledge
Target reached
MSB
LSB
Page 192 of 233
Parker Hannifin S.p.A S.B.C. Division
Name
Target
reached
Hi-drive User Manual
Value
Description
0
Halt = 0: Target position not reached Halt = 1: Axle decelerates
1
Halt = 0: Target position reached Halt = 1: Velocity of axle is 0
Trajectory generator has not assumed the positioning values
(yet)
Trajectory generator has assumed the positioning values
No following error
Following error
Set-point
acknowledge
0
1
0
1
Following
error
Table 10: Profile position mode bits of the statusword
14.2.5.2 Object dictionary entries
14.2.5.2.1 Objects defined in this chapter
Index
607A
Object
VAR
Name
Target position
Type
INTEGER32
Attr.
rw
M/O
M
Index
6081
6083
6084
6085
6086
Object
VAR
VAR
VAR
VAR
VAR
Name
Profile velocity
Profile acceleration
Profile deceleration
Quick stop deceleration
Motion profile type
Type
UNSIGNED32
UNSIGNED32
UNSIGNED32
UNSIGNED32
INTEGER16
Attr.
rw
rw
rw
rw
rw
M/O
M
M
O
O
M
Index
6040
6041
605A
6093[1,2]
6094 [1,2]
6097 [1,2]
Object
VAR
VAR
VAR
ARRAY
ARRAY
ARRAY
Name
Controlword
Statusword
Quick stop option code
Position factor
Velocity encoder factor
Acceleration factor
Type
UNSIGNED16
UNSIGNED16
INTEGER16
UNSIGNED32
UNSIGNED32
UNSIGNED32
Chapter
dc
dc
dc
fg
fg
fg
14.2.5.2.2 Object 607Ah: Target position
The target position is the position that the drive should move to in position profile mode using
the current settings of motion control parameters such as velocity, acceleration, deceleration,
motion profile type etc. The target position is given in user defined position units. It is converted
to position increments using the position factor. The target position will be interpreted as
absolute or relative depending on the ‘abs / rel’ flag in the controlword.
Page 193 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
OBJECT DESCRIPTION
INDEX
Name
Object Code
Data Type
Category
607Ah
Target position
VAR
INTEGER32
Conditional;
Mandatory, if pp or pc supported
EN TRY DESCRIPTION
Access
PDO Mapping
Value Range
Default Value
rw
Possible
INTEGER32
No
14.2.5.2.3 Object 6081h: Profile velocity
The profile velocity is the velocity normally attained at the end of the acceleration ramp during a
profiled move and is valid for both directions of motion. The profile velocity is given in user
defined speed units. It is converted to position increments per second using the velocity encoder
factor.
OBJECT DESCRIPTION ENTRY DESCRIPTION
INDEX
Name
Object Code
Data Type
Category
6081h
Profile velocity
VAR
UNSIGNED32
Conditional;
Mandatory, if pp or pv supported
Access
PDO Mapping
Value Range
Default Value
rw
Possible
UNSIGNED32
No
14.2.5.2.4 Object 6083h: Profile acceleration
The profile acceleration is given in user defined acceleration units. It is converted to position
increments per second2 using the normalizing factors.
Page 194 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
OBJECT DESCRIPTIION
INDEX
Name
Object Code
Data Type
Category
6083h
Profile acceleration
VAR
UNSIGNED32
Conditional;
Mandatory, if pp or pv supported
ENTRY DESCRIPTION
Access
PDO Mapping
Value Range
Default Value
rw
Possible
UNSIGNED32
No
14.2.5.2.5 Object 6084h: Profile deceleration
The profile deceleration is given in user defined acceleration units. It is converted to position
increments per second2 using the normalizing factors.
OBJECT DESCRIPTIION
INDEX
Name
Object Code
Data Type
Category
6084h
Profile deceleration
VAR
UNSIGNED32
Conditional;
Mandatory, if pp or pv supported
ENTRY DESCRIPTION
Access
PDO Mapping
Value Range
Default Value
rw
Possible
UNSIGNED32
No
14.2.5.2.6 Object 6085h: Quick stop deceleration
The quick stop deceleration is the deceleration used to stop the motor if the ‘Quick Stop’
command is given and the quick stop option code (see 605Ah) is set to 2. The quick stop
deceleration is given in the same units as the profile acceleration.
Page 195 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
OBJECT DESCRIPTION
INDEX
Name
Object Code
Data Type
Category
6085h
Quick stop deceleration
VAR
UNSIGNED32
Optional
ENTRY DESCRIPTION
Access
PDO Mapping
Value Range
Default Value
rw
Possible
UNSIGNED32
No
14.2.5.2.7 Object 6086h: Motion profile type
The motion profile type is used to select the type of motion profile used to perform a profiled
move.
Value Description
0
Linear ramp (trapezoidal profile)
OBJECT DESCRIPTION
INDEX
Name
Object Code
Data Type
Category
6086h
Motion profile type
VAR
INTEGER16
Conditional;
Mandatory, if pp or pv supported
ENTRY DESCRIPTION
Access
PDO Mapping
Value Range
Default Value
rw
Possible
INTEGER16
0
14.2.5.3 Functional description
Two different ways to apply target positions to a drive, are supported by this device profile.
Set of set-points: After reaching the target position the drive unit immediately processes the next
target position which results in a move where the velocity of the drive normally is not reduced to
zero after achieving a set-point.
Page 196 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Single set-point: After reaching the target position the drive unit signals this status to a host
computer and then receives a new set-point. After reaching a target position the velocity
normally is reduced to zero before starting a move to the next set-point.
The two modes are controlled by the timing of the bits ‘new set-point’ and ‘change set
immediately’ in the controlword and ‘set-point acknowledge’ in the statusword. These bits allow
to set up a request-response mechanism in order to prepare a set of set-points while another set
still is processed in the drive unit. This minimizes reaction times within a control program on a
host computer.
DATA
New setpoint
(2)
(4)
(6)
Change set
immediately
(1)
Setpoint
acknowledge
(3)
(5)
Figure 17: Set-point transmission from a host computer
Figure 17, Figure 18 and Figure 19 show the difference between the "set of set-points" mode and
the "single set-point" mode. The initial status of the bit ‘change set immediately’ in the
controlword determines which mode is used. To keep simple these examples, only trapezoidal
moves are used.
If the bit ‘change set immediately’ is "0" (continuously drawn line in Figure 17) a single setpoint is expected by the drive (1). After data is applied to the drive, a host signals that the data is
valid by changing the bit ‘new set-point’ to "1" in the controlword (2). The drive responds with
‘set-point acknowledge’ set to "1" in the statusword (3) after it recognized and buffered the new
valid data. Now the host may release ‘new set-point’ (4) and afterwards the drive signals with
‘set-point acknowledge’ equal "0" its ability to accept new data again (5). In Figure 18 this
mechanism results in a velocity of zero after ramping down in order to reach a target position
x1.at t1. After signaling to the host, that the set-point is reached like described above, the next
target position x2 is processed at t2 and reached at t3.
Figure 18: Single set-point
Page 197 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
If the bit ‘change set immediately’ is "1" (dashed line in Figure 17) the new target position will
be active immediately. In Figure 19 the drive receives the first target position at t0. At the time
point t1 the drive receives a second target position. The drive readapts the actual move to the
new target position immediately.
Figure 19: Change set immediately
14.2.5.4 Functional description
Figure 33 shows the meaning of the sub-function position reached. Symmetrically around the
target position a window is defined for the accepted position range. If a drive is situated in the
accepted position range over the time position window time the bit target reached (bit 10) in the
statusword is to set.
Position
Accepted position range
Position window
Position not reached
Position window
Position reached
Position not reached
Figure 33: Position reached
Figure 34 shows the meaning of the sub-function following error in the profile position mode.
Symmetrically around the reference position a window is defined for the accepted following
error tolerance. If a drive is situated out of the accepted position range for more than following
error time out time the bit following error (bit 13) in the statusword is set.
Accepted following
Page 198 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Position
Error tollerance
Following error
Following
error
Following
error
window
window
No following error
Following error
reference position Figure 34: Following error
The following error window is used to signal by mean of status word the servo error condition on
user defined BIT14 when Interpolated position mode is active and with standard bit 13 in profile
position mode. This feature isn’t valid for rel 206 yet.
If the user sets b78.3 a fault reaction sequence is entered and according to the fault reaction
option code (valid values 0,1,2) the motor is stopped and finally disabled sending an emergency
message with error code 0xff11 and user data loaded with pr[108:109].This feature isn’t valid
for rel 206 yet.
Page 199 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
14.2.6 Interpolated Position Mode
In Interpolated Position Mode the cycle time is set in the object 0x1006 'communication cycle
period' and depending on the value set in this object different ways of regulation are possible.
If the value is less than 2500 µsec the position loop is executed at the moment the sync signal is
received the position reference received on the PDO is directly processed as target of the position
loop. If the value is more or equal than 2500 µsec the position reference received is interpolated
according the interpolation sub mode index 0x60c0 , the interpolation may be cubic or linear.
If object 0x60c0 is 0 the interpolation algorithm is linear otherwise if –1 is cubic with both
position and velocity reference, if –2 is cubic with position reference only.
If on the synchronous PDO 4 rx it is not mapped the position reference the position loop is not
executed but the velocity reference received is set, the velocity reference may be supplied in
counts/sec or RPM respectively mapping object 0x60c1.2 or 0x60c1.3, in this case the external
controller executes position loop.
Note: In interpolated position mode factor group conversion are not active. If the cycle time is
less than 2500 µsec the feedforward of velocity may be computed by the drive (if bit 230.7 is
set) from the delta of position reference in the cycle time (gain of feedforward component should
be set accordingly with the cycle time). Otherwise feedforward of velocity may be sent with
PDO4 rx mapping in RPM units the object 0x60c1.3.
Depending on the different algorithms of interpolation there is a different delay between the
moment the target position is received on the PDO and validated by the sync and the moment
when the target position is active in the trajectory setpoint of the motor.
In case of cycle time less than 2500 µsec the position loop trajectory setpoint is immediately
upgraded with the last received position setpoint as soon as the sync signal is received.
In case of cycle time longer than 2500 µsec, both with linear interpolation and cubic
interpolation with position and velocity, the point specified in the target position received on the
PDO will be activated as trajectory setpoint at the end of the cycle time started with the sync
signal that validated the target position, so with a cycle time delay.
As last, in case of cycle time longer than 2500 µsec and cubic interpolation with position
reference only, the point specified in the target position received on the PDO will be activated as
trajectory setpoint at the end of the next cycle time started with the sync signal that validated the
target position, so with two cycle time delay.
Index Object
Name
Type
Attr. M/O
60C0h VAR
Interpolation sub mode select INTEGER16 rw
O
60C1h ARRAY Interpolation data record
INTEGER32 rw
O
Index
6040h
6041h
605Ah
6060h
6061h
6063h
Object
VAR
VAR
VAR
VAR
VAR
VAR
Name
Controlword
Statusword
Quick stop option mode
Modes of operation
Modes of operation display
Position actual value*
Page 200 of 233
Type
UNSIGNED16
UNSIGNED16
INTEGER16
INTEGER8
INTEGER8
INTEGER32
Chapter
dc
dc
dc
dc
dc
pc
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
14.2.6.1 Object 60C0h: Interpolation sub mode select
For the interpolated position mode a manufacturer may offer different interpolation algorithms.
This object reflects or changes the actually chosen interpolation mode.
OBJECT DESCRIPTION
INDEX
Name
Object Code
Data Type
Category
60C0h
Interpolation sub mode select
VAR
INTEGER16
Optional
ENTRY DESCRIPTION
Access
PDO Mapping
Value Range
Default Value
rw
Possible
0..-2
0
DATA DESCRIPTION
Value
-2
-1
0
+1..+32767
Description
Cubic interpolation only position
Cubic interpolation speed+position
Linear interpolation
reserved
14.2.6.2 Object 60C1h: Interpolation data record
The interpolation data record are the data words which are necessary to perform the
interpolation algorithm. The number N of data words in the record is defined by interpolation
data configuration. The interpretation of the data words in interpolation data record may vary
with the different possible interpolation modes as set by the interpolation sub mode select.
For the linear interpolation mode each interpolation data record simply can be regarded as a new
position set-point. To describe a cubic spline interpolation e.g., four or more data words are
needed for the spline coefficients, and further interpolation parameters.
After the last item of an interpolation data record is written to the devices input buffer, the
pointer of the buffer is automatically incremented to the next buffer position.
OBJECT DESCRIPTION
INDEX
60C1h
Name
Interpolation data record
Object Code ARRAY
Data Type
INTEGER32
Category
Optional
Page 201 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
ENTRY DESCRIPTION
Sub-Index
Description
Entry Category
Access
PDO Mapping
Value Range
Default Value
0
number of entries 3
Mandatory
ro
No
3
No
Sub-Index
Description
1
Position setpoint in counts
the first parameter of ip function fip(x1, .. xN)
Entry Category Mandatory
Access
rw
PDO Mapping Possible
Value Range
INTEGER32
Default Value No
Sub-Index
Description
2
Velocity setpoint in counts/sec
the second parameter of ip function fip(x1, .. xN)
Entry Category Optional
Access
rw
PDO Mapping Possible
Value Range
INTEGER32
Default Value No
Sub-Index
Description
3
Velocity setpoint in rpm
the 3-rd parameter of ip function fip(x1, .. xN)
Entry Category Optional
Access
rw
PDO Mapping Possible
Value Range
INTEGER32
Default Value No
Page 202 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Interpolated
position mode selected
Interpolation inactive
Disable
interpolation
Enable
interpolation
Disable
voltage shutdown
Changoing the mode of
operation or deselect
interpolated position mode
Operation enbled
Interpolation active
Page 203 of 233
Quick stop
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
14.2.7 Drive parameters
Some commands and parameters are added concerning CANopen
Par.
Description
Pr416 CANOPEN_CTRL_WORD. Check the drive status.
Pr417 CANOPEN_STATUS_WORD. Check the drive
status.
This
parameter
Pr418 CANOPEN_DS301_STATUS.
indicates the status of DS301 communication profile
Par.
b78.1
b78.2
b78.4
b78.9
b78.10
b79.8
b415.0
b415.1
b415.2
b415.3
Field
R
R
R
Range Def. Ris.
-32768÷
0
1
+32767
-32768÷
0
1
+32767
-32768÷
0
1
+32767
Description
Conversion of velocity. (1) (1) conversion of velocity and acceleration
in standard units counts/sec e counts/sec2 , (0) conversion of velocity
and acceleration in rpm e msec/krpm
Display on keypad. (1) disable automatic display on keypad of
CANopen status change.
Set to 1 every end CANopen ramp (object 0x2065) of disable delay. It
can be used to management the motor brake.
Remote mode. (1) Remote mode CANopen, (0) remote disabled.
Static brake command. (1) Enables static brake command from
ctrlword CANopen.
Enable sync. (1) enables missing sync check DSP402 CANopen.
Displaying on keypad state machine DS301. (1) comm. displaying on
keypad state machine DS301 (autoreset).
Displaying on keypad state machine DS402. (1) comm. displaying on
keypad state machine DS402 (autoreset).
Displaying on keypad controlword DS402. (1) displaying on keypad
control word DS402 (autoreset).
Displaying on keypad statusword DS402. (1) displaying on keypad
status word DS402 (autoreset).
Field
R/W
Def.
0
R/W
0
R/W
0
R/W
R/W
0
0
R/W
R/W
0
0
R/W
0
R/W
0
R/W
0
Noted with an * the item that are not displayed at the execution of command CO
If not inhibited by 78.2=1 any status change of the state machines 301 or 402 is displayed for
about 2 seconds on the keypad
Note: When in remote mode the bit b40.6, b40.2 and the parameters Pr8, Pr9, Pr10, Pr11, Pr12
and Pr55 are handled by firmware according to CANopen network setting and commands and
should not be modified by the user.
Page 204 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
14.2.8 CANopen monitor by ASCII commands
The ASCII protocol o rs232 support an additional command to display CANopen settings, typing
CE or CO command the CANopen setting page is shown.
CE
------------------------------- CANopen Info page ----------------------------...............................................................................
Baud rate :
1 Mbps
Node Address: 001
Communication status : Pre-Operational
bus off: NO bus warning: NO
State Machine:
Fault
Mode of operation:
Interpolated Position
...............................................................................
Control word:
0 0x0000
0000000000000000
bit0 : Switch On
0
bit1 : Enable voltage
0
bit2 : Quick Stop
0
bit3 : Enable operation
0
bit4 : Operation mode specific
0
bit5 : Operation mode specific
0
bit6 : Operation mode specific
0
bit7 : Fault Reset
0
bit8 : Halt
0
bit9 : Reserved
0
bit10 : Reserved
0
bit11 : Manufacturer specific
0
bit12 : Manufacturer specific
0
bit13 : Manufacturer specific
0
bit14 : Manufacturer specific
0
bit15 : Manufacturer specific
0
...............................................................................
Status word:
8712 0x2208
0010001000001000
bit0 : Ready to Switch On
0
bit1 : Switched On
0
bit2 : Operation enabled
0
bit3 : Fault
1
bit4 : Voltage enabled
0
bit5 : Quick stop
0
bit6 : Switch on disabled
0
bit7 : Warning
0
bit8 : Manufacturer specific
0
bit9 : Remote
1
bit10 : Target Reached
0
bit11 : Internal limit active
0
bit12 : Operation mode specific
0
bit13 : Operation mode specific
1
bit14 : Manufacturer specific
0
bit15 : Manufacturer specific
0
Page 205 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
...............................................................................
Communication
PDO 1 TX
Mapping
COB-ID
Valid: N RTR: N
0x60410010 0x181
Transmission type: 254
Event time:
0
Inhibit time:
0
------------------------------------------------------------------------------Communication
PDO 1 RX
Mapping
COB-ID
Valid: N
0x60400010 0x201
...............................................................................
Communication
PDO 2 TX
Mapping
COB-ID
Valid: N RTR: N
0x281
Transmission type: 254
Event time:
0
Inhibit time:
0
------------------------------------------------------------------------------Communication
PDO 2 RX
Mapping
COB-ID
Valid: N
0x301
...............................................................................
Communication
PDO 4 TX
Mapping
COB-ID
Valid: N RTR: N
0x60630020 0x481
Transmission type: 1
Event time:
0
Inhibit time:
0
------------------------------------------------------------------------------Communication
PDO 4 RX
Mapping
COB-ID
Valid: N
0x60C10120 0x501
...............................................................................
Communication
SYNC
Valid: N
...............................................................................
Communication
EMCY
Valid: Y
COB-ID
0x080
COB-ID
0x081
Page 206 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
15 PROGRAMMING THE CONVERTER THROUGH A PC
A serial kit (USBTODRIVE) is available to communicate with the converter through a
personal computer. The kit includes a RS-422/RS-232 converter and serial link cable.
The installation requirements for the freely supplied communication software MotionWiz
are a personal computer (PII or higher recommended) running on Windows* 98 or later, a
mouse to navigate within the program and a serial link to the converter. The main
features of Motion Wiz are:
- serial connection to up to 32 converters reading and setting key parameters and
converter commands
- reading and setting operating mode parameters and commands
- functional block diagrams
- Pico-PLC programming in text and ladder format
- display of Pico-PLC program during operation
- status of inputs and outputs
- parameter setting storage, including Pico-PLC program in one file
- parameter setting loading, including Pico-PLC program from one of the
previously stored files (selectable)
- oscilloscope function
*Windows and the Windows logo are registered marks or trademarks of Microsoft Corporation in the United States and/or in other countries
Page 207 of 233
.
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
15.1 MotionWiz
The configuration tool is called “MOTIONWIZ” and is used to program the drive while
controlling the whole system in real time. PLC programs can also be edited and new files can be
generated.
The first step is to install the program*:
click on the icon “SetupMotionWiz.exe”
Follow the instructions that appear during the installation . An icon linking to the program will
be generated on your desktop at the end of the installation process :
Click on the icon to start the configuration program. The following window will be displayed on
your monitor:
Lang.
continued:
File menu
Data on drive
Data on PC
It is possible to select the desired language: Italian or English.
How to generate a new file:
to set the data for motor and drive, use the databases provided by the software, that can be
accessed through the icons below the figures (when the drive and the motor pictures are out of
focus , it means that the relevant data have not been set yet).
Press “ENTER” to access the configuration functions.
How to use an existing file:
the “file menu” shows a list of most recent files. To open a file, click on a name in the list
Alternatively, using the “Open” tab it is possible to “search” previously stored files selecting the
relevant route.
* The MotionWiz program can be found on the CD rom supplied with the drive or downloaded from our website: www.sbcelettronica.com
Page 208 of 233
Parker Hannifin S.p.A S.B.C. Division
15.2
Hi-drive User Manual
Hyperterminal connection
15.2.1 Creating and setting a connection
In order to create a connection with Hi-Drive (on port X4) go through the following steps.
Launch the HyperTerminal program: start menuÆ programs Æ accessories Æ communications
1. Create a new connection
2. Select port
3. Select communication port settings:
Page 209 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
The Baudrate (Bit per second) depends on the actual Hi-Drive setting, all other values are
compulsory.
4. Change terminal settings:
5. In the terminal window, select the menu fileÆ properties. Select the following settings
Enter commands as prescribed in the specifications of the ASCII protocol.
Page 210 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
15.2.2 ASCII protocol port RS-232
This is the protocol used on port TS232 of the drive.
This is used for a point-to-point communication. Therefore, only one driver can be connected to
this interface, and it is not necessary to enter the drive’s address.
The messages used in communication are reported in the table below, where the message fields
feature a “#”followed by a letter.
Field
#a
#b
#c
#d
#e
#g
#h
#i
[m]
#n
#1
#2
#3
#n
Range
Max
Description
Parameter number
Bit number
Pico-PLC instruction number
Table number
Point of the table number
Word (16 bit) value (signed)
(unsigned)
Long (32 bit) value (signed)
Bit status value
Pico-PLC instruction mnemonic code
(2, 3 or 4 characters)
16 character Text Message string
Pico-PLC 1st operand
Pico-PLC 2nd operand
Pico-PLC 3rd operand
16-char message string
Min
NUM_PAR-1
15
255
N_TABLES-1
END_ADR - START_ADR
0
0
0
0
0
32767
65535
-32767
0
+232-1
1
-232
0
See the paragraph on Pico-PLC
text
See the paragraph on Pico-PLC
See the paragraph on Pico-PLC
See the paragraph on Pico-PLC
NUM_PAR and N_TABLES, and START_ADR, END_ADR for each table can be read directly
in the drive through dedicated commands.
HI-Drive ASCII protocol: messages definition
Write Commands
Description
Tx Format
Word parameter value
P#a=#g<CR>
Long parameter value
PL#a=#h<CR>
Bit status
B#a.#b=#i<CR>
overwrite Pico-PLC instruction (#)
I#c=#m#1.#2.#3<CR>
d word point value TABLE
T#d.#e<CR>
d long point value TABLE
TL#d.#e<CR>
Page 211 of 233
Parker Hannifin S.p.A S.B.C. Division
Description
Word parameter value(*)
Long parameter value
Bit status
Hi-drive User Manual
Read commands
Tx Format
P#a<CR>
PL#a<CR>
B#a.#b<CR>
Pico-PLC instruction
d word point value TABLE
d long point value TABLE
Null command
Command abort(**)
I#c<CR>
T#d.#e<CR>
TL#d.#e<CR>
<CR>
xxxxxx<ESC>
Error messages
Description
Rx Format
#g<CR><LF>
#h<CR><LF>
#I<CR><LF>
#m<SPACE>#1.#2.#3<CR
><LF>
#g<CR><LF>
#h<CR><LF>
<CR><LF>
<CR><LF>
RX message string
Write command success
Command aborted
Syntax error or bad parameter or bit number
or value out of range
Ok<CR><LF>
<CR><LF>
Syntax Error<CR><LF>
Pico-PLC
Run<CR><LF>
<CR><LF>COM
Error<CR><LF>
<CR><LF>Buffer
Overflow<CR><LF>
Pico-PLC running
COM framing or overrun error
Buffer overflow (command too long)
in
Notes:
(*)
the drive requests a word with or without sign, depending on the parameter format.
- Word parameter and low/high word in a long parameter Æ signed
- Signless Word and binary parameter
Æ unsigned
(**) the previously received characters are ignored and the command is aborted: the drive
responds as if it had received a void command.
(#)
do not write instructions and do not save when the drive PLC is in RUN mode
Page 212 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
There is no difference between various cases as far as the reception of characters is concerned;
some special characters are used for the following functions:
Char
SPACE
HEX
0x20
BS
0x80
ESC
0x1B
CR
0x0D
LF
0x0A
Description
No meanings: any space character received will be removed as
insignificant.
Delete last character: if one of these character is received the last
character received will be removed from the buffer
Abort: if this character is received the command line will be interrupted
and the buffer reset
End of message: when this character is received the buffer is complete so
the command line can be interpreted
Line feed: end of line
COM port settings
The communication is based on a standard RS232 model and Hi-drive has the following setting:
COM port settings
Data bit
8
Parity
None
Stop bit
1
The baudrate can be selected with the values listed in the table :
Hi-drive Response time
Baudrate
Timout
9600
(*)
19200
(*)
38400
(*)
56700
(*)
(*) Under definition
Page 213 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
16 USE OF (OPTIONAL) KEYPAD
IDLE
Pb. 0041
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
The keyboard-display module is easy to use. It is used to program the functional data, control the
status of the converter and send commands. It can also store data and transfer them to other
drives. The module is equipped with five keys, located right under the display. The keys are
marked as follows respectively : [S], [+], [–], [T], [E].
The consists of two separate lines: the upper line indicates the drive status (left), the definition of
the displayed parameter, its number or the instruction line of the Pico-PLC. The lower line shows
the data (in case of a binary parameter, the number of bits can go from zero to fifteen, right to
left), or the instruction either of the command or of the Pico-PLC.
The keys functions are as follows:
- S, SHIFT, it is used in combination with the other keys to allow the pointer to move within
the fields:
o With T key, the movement within the fields is in the opposite direction (anticlockwise).
o With + or – key, to move the pointer within a field on a digit with major or less
“weight” : in this way the tens or hundreds digit can be modified , or…, to enter
those values that, otherwise, would take much longer, or to highlight the bit to be
modified within binary parameters. If the pointer is in the field with the Pico-PLC
instruction number, a new instruction line can be added (using +, the line is added
before the displayed instruction ), or deleted (using –).
- +, increases the data highlighted by the pointer; in case of PLC instructions, any time you
press the key a different instruction is shown. If it is used with the S key, it takes on other
functions (see definition of S key). In order to change the bit status, press and hold 1 sec.
- -, decreases the data highlighted by the pointer; in case of PLC instructions, any time you
press the key a different instruction is shown. If it is used with the S key, it takes on other
functions (see definition of S key). In order to change the bit status, press and hold 1 sec.
- T, this key is used to change the field highlighted by the pointer. With S key, the switch
between fields is in the opposite direction (anti-clockwise).
- E, ENTER, to confirm the data entered or modified. The modified or entered data or
instruction must be saved before going to the next screen, otherwise all changes will be
lost. The confirmation command is limited to what appears on the display, and not to all
parameters, instructions and tables.
IMPORTANT: instructions can be modified even when the Pico-PLC is running
(Pr39.13=1). Before making any modifications, stop the Pico-PLC.
The Pico-PLC instructions can be modified using the “+” and “-“ keys (ensure that the pointer
has been moved to highlight the Pico-PLC instruction). In order for a modification to become
effective, press “E”: a message confirming the modification is displayed .
Page 214 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
The Pico-PLC instructions data can be modified using the “+” and “-“ keys (ensure that the
pointer has been moved to highlight the Pico-PLC instruction). In order for a modification to
become effective, press “E”: a message confirming the modification is displayed .
The value of decimal parameters and the parameter data in the tables can be modified using the
“+” and “-“ keys (ensure that the pointer has been moved to highlight the value of the decimal
parameter or the parameter value in the tables ).
The bit status in binary parameters can be modified using the “+” and “-“ keys (ensure that the
pointer has been moved to highlight the bit to be modified). The bits are numbered from 0 to 15
and are shown in growing order, right to left. In order to move the pointer between bits, left to
right, press the “S” and “+” keys simultaneously; to move the pointer between bits, right to left,
press the “S” and “-”keys simultaneously).
- The data format to be entered in the parameter is already set. If the data is not accepted it
means that its format does not match the required format.
- All double word parameters are displayed entirely, not limited to either the high word or the
low word. This makes it easier to understand the “long” parameter.
- The keypad can update and store all the parameter values in a 2Kbyte memory. Another
2Kbyte memory is dedicated to CAM tables. This system makes it easy to transfer the stored
data to other Hi-drive units.
- Error messages are also displayed on the screen.
- Whenever entering a Pico-PLC instruction, in order for the entered instruction to be saved,
press the Enter key. Otherwise, the previous instructions will remain effective.
- A confirmation message will be displayed: changing, inserting, deleting.
The parameter definition can be identified by the following markings: Pr (parameter), Pb (binary
parameter), In (Pico-PLC instruction), Cmd (commands), T (tables):
Pr. xx
Indicates parameter xx for 16 bit word.
PL. xx
Indicates parameter xx for 32 bit word, marked as long parameters.
Pb. xx
Indicates the binary parameter at 16 bit xx.
In. xx
Indicates the xx instruction number of the Pico-PLC program.
Ty. xx
Parameter table, y indicates the table number, xx is the parameter number.
Cmd send keypad command. The type of command is displayed on the second line.
Here follows a list of possible commands (the pointer must be positioned in the second line.
Other commands can be seen using the + key):
ƒ Upload and download of parameters and tables. The data are stored in the Eeprom.
ƒ Upload and download of Pico-PLC instructions. The data are stored in the Eeprom.
ƒ Reduction or enlargement of the display menu. The enlarged menu can display all
parameters (in order to see all parameters, press the Enter key to activate this function).
Each command must be performed from the command Enter. Through these commands the
settings can be transferred between drives. Ensure that the drive and motor versions where the
parameters will be applied have been correctly identified: ensure that drive and motor have the
same features.
The following messages may be displayed on the screen, in addition to the value of the
parameters and the instructions of the Pico-PLC:
IdLE
At start up. It indicates that the converter is disabled.
run
At start up and by Pr0, this message indicates that there is no alarm and that the
converter is enabled. The motor shaft may be rotating.
Er. xx
This message indicates that the converter has detected an alarm (xx indicates the alarm
code) and has therefore been disabled. When it detects an alarm, the converter is
brought to Pr0 and the alarm code is displayed.
dEF
Indicates that the drive is set to default status and must be programmed using the
motor key parameters. Error code = 15.
It is possible to select what parameter you want to be displayed when the drive is powered on.
Follow the procedure below: connect the keypad to the drive to power it up; move to the
Page 215 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
parameter you want to be displayed. Press Enter. A “default parameter” message is displayed on
the screen, warning that the previous setting has been changed. Switch off the keypad
(disconnect the keypad from the drive) and switch it on again (connecting it to the drive).
Hi-drive keypad menu control
0
Bottom line
Tot>line
Mode
Al'g
Val ue
Cyclically moves cu·sor posnion to next field
GO
~
®
®
..!I.
increments/decrements value &t cursor
Enters the change hto drive
Shift • adddional/special functions
'T' cycles cursor back to 1st field
Uum bor of opernn(l & d OIJOn ds
on in st•·u ction
Additional functions
Set 11o w et · liJ) d efault Pr 0 1 Pb
@)+(D = Reverse tab ulate
between fields
Page 216 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
17 Appendix A : Conventions
Reference
Positive
Motor shaft movement(motor shaft
view)
Torque
Resolver counter
Encoder output
Tachometer signal
Iu
Iv
Encoder In. A
B
Frequency A
Positive
Increments
A
B
Positive
torque • sin (ϑ )
2•π ⎞
⎛
torque • sin ⎜ϑ +
⎟
3 ⎠
⎝
Counter increment
Counter increment
Direction B
18 Appendix B : Flash information
• TO SAVE PARAMETERS USE b42.15
• TO SAVE THE PLC PROGRAM USE b42.14
• TO CHANGE THE INSTRUCTIONS, PLC b39.13 MUST BE 0
• WHEN THE OPERATING MODE IS CHANGED, USE b42.13 TO LOAD THE DEFAULT
PARAMETERS (b40.2 MUST BE 0)
• BEOFRE CHANGING Pr181, MAKE SURE THAT b40.2=0
• THE SPEED REFERENCE WILL BE LIMITED TO THE VALUE OF Pr32
• WHEN TORQUE CONTROL IS USED, Pr2 AND Pr3 MUST BE SET TO 1000
• WHEN AN ACTIVE OPERATING MODE IS USED, b40.2 MUST BE 1
• IF READ-WRITE PARAMETERS CANNOT BE CHANGED USING THE KEYPAD,
MAKE SURE THAT b42.1 IS 1. IF IT WAS 1, PROBABLY THE SAME PARAMETERS
ARE MODIFIED BY THE PLC PROGRAM.
Page 217 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
19 Appendix C : Software timing
Period
64 μs
128 μs
512 μs
128 μs
128 μs
512 μs
1.024 ms
6.144 ms
6.144 ms
6.144 ms
6.144 ms
6.144 ms
Task
Current control
Speed control
Fast operating mode management
Torque limit management
Speed reference management
Braking resistor management
Slow operating mode management
Thermal motor image
Digital inputs
Pico-PLC program scanning
Digital outputs
Speed window management
Page 218 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
20 Appendix D : Alarms
Alarm
Remedies
Code in Pr23
0
1
No alarm
Overvoltage
2
3
Undervoltage
Overcurrent
4
Speed loop FBK error
5
PTC motor alarm
6
Power
overtemperature
7
External alarm
8
Auxiliary alarm
10 (*)
PLC check sum
11 (*)
Parameter check sum
13
14
CANopen connection
Overload braking
15
Default parameters
16
18
CANopen synchronization
Power
module
overtemperature
19
Power module alarm
module
Check the three-phase power line.
Check the break circuit and the braking resistor
Check the application
Check the three-phase power line.
Check for any mechanical blockage and make sure
the motor is the appropriate size for its current use.
Check the motor connections and any phase-phase
or phase-ground short-circuits.
Check the length and type of the motor cable in
use.
Make sure a mains filter isn’t connected to the
motor!
Check the connections of the speed loop and the
connectors on both sides (drive-motor).
Check the PTC connection cable.
If the alarm persists, disable the drive, remove
power from the motor and de-energize the drive
(24VDC). Remove the PTC connector from the
drive, short –circuit the PTC (connecting PTC+
and PTC-) on the same drive terminal block.
Supply power to the drive (24VDC). If the alarm
persists, either the drive is in fault state, or the PTC
on the motor is in fault state. (at the end of the test,
remove the PTC short-circuiting connection).
Check the cooling fans and for any restrictions to
air flow.
Check the breaking cycle.
Check the ambient temperature in the electric
cabinet where the drive is installed, as well as the
ambient temperature outside the cabinet.
Depends on the application (see Pico-PLC
program)
Depends on the application (see Pico-PLC
program)
Set and save default parameters, switch off and on
again the drive and repeat programming.
Set and save default parameters, switch off and on
again the drive and repeat programming.
CANopen communication interrupted
Check the cycle and if it’s necessary use an
external braking resistor
Set and save default parameters, switch off and on
again the drive and repeat programming.
CANopen communication not sync.
(only for HID75, 100 and 130)
Check the cooling fans and for any restrictions to
air flow.
Check the breaking cycle.
Check the ambient temperature in the electric
cabinet where the drive is installed, as well as the
ambient temperature outside the cabinet.
(only for HID75, 100 and 130)
Check the motor cable and the motor: possible
short-circuits between any phase-phase or phaseground.
Page 219 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Alarm
Undervoltage 24VDC
Code in Pr23
21
22
Ambient over temperature
24 (**)
28
Braking
transistor
protection
Speed
loop
FBK
initialization error
Position
loop
FBK
initialization error
Position loop FBK error
30
Keypad parameters
25 (**)
26 (**)
Current limit (I2T)
I2T
“the red led is
blinking
continuously ”
Remedies
The drive input voltage is below the low limit :
voltage is too low.
Check the cooling fans and for any restrictions to
air flow.
Check the ambient temperature in the electric
cabinet where the drive is installed, as well as the
ambient temperature outside the cabinet.
Short-circuit braking resistance. If an external
braking resistor is connected to the drive, check the
resistor statures and wiring.
Check the speed FBK settings.
Check the speed FBK connection.
Check the position FBK settings.
Check the position FBK connection.
Check the connections of the position loop and the
connectors on both sides (drive-motor).
The parameters, saved on keypad, are
compromised.
The drive goes in I2T mode due to an overload (the
current required is more than the current that can
be supplied).
Check :
The wiring between drive and motor (there should
be no inverted phases). Take special care with
motors where the connector is replaced by a
terminal block : it’s easy to make a mistake.
Adhere strictly to the wiring diagrams.
Mechanical dimensioning
(*) reset only after default values have been loaded and saved.
(**) can be only reset at the next power on.
(✎)
Pr23
overvoltage
Drive ok
undervoltage
41.4
overcurrent
Speed loop FBK error
Converter
overtemperature
41.7
41.8
Default
parameter
Check Sum PLC
“0”
41.5
Hardware enable
Software enable
40.9
Check Sum parameter
Undervoltage 24V
Mbient overtemperature
Braking resistance protection
Speed FBK initializing error
Pr76
Encoder phasing
result
41.6
Phasing ok
Position FBK initializing error
Position loop FBK error
PTC alarm active
Page 220 of 233
41.12
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
21 Appendix E : Continuous working
In continuous operation, the power supplied to the drive must not go beyond the limit curves
shown in the following figures.
The limit power depends on the voltage and frequency of the supply network.
HID2 – 1-phase supply network
450
425
400
375
50 Hz
350
Pout [W]
325
300
275
250
60 Hz
225
200
175
150
125
100
100
150
200
250
300
Vac phase – neutral [V]
HID2 – 3-phase supply network
1100
1050
1000
950
50 Hz
Pout [W]
900
850
800
750
60 Hz
700
650
600
550
500
150
200
250
300
350
400
Vac phase – phase [V]
Page 221 of 233
450
500
550
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
HID5/HID8 – 1-phase supply network
800
750
700
Pout [W]
650
50 Hz
600
550
500
60 Hz
450
400
350
300
100
150
200
250
300
350
Vac phase – neutral [V]
HID5/HID8 – 3-phase supply network
2400
2200
Pout [W]
2000
50 Hz
1800
1600
60 Hz
1400
1200
1000
100
150
200
250
300
350
400
Vac phase – phase [V]
Page 222 of 233
450
500
550
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
HID16/HID25 – 1-phase supply network
1500
1400
1300
1200
50 Hz
Pout [W]
1100
1000
60 Hz
900
800
700
600
500
100
150
200
250
300
Vac phase – neutral [V]
HID16/HID25 – 3-phase supply network
3500
3300
3100
Pout [W]
2900
50 Hz
2700
2500
60 Hz
2300
2100
1900
1700
1500
150
200
250
300
350
400
Vac phase – phase[V]
Page 223 of 233
450
500
550
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
(✎)
22 Appendix F : External capacitor
The battery of external capacitors (see the “Modulc” manual) may be used instead of (or in
addition to) the braking resistor, according to the application. The energy generated during the
braking phase is accumulated in to the capacitor without loss of heat.
Connection plan:
DC +
Terminal block
X1
+
RN
The external capacitor depends to the size of drive, described in the following char.
HID Max. external capacitor [µF]
2
1100
5
1100
8
2200
10
2200
16
4400
25
4700
35
2200
45
2200
75
100
130
-
Connections :
use only stranded copper wire rated for 60/75°C, minimum 600V
max length : 50cm
minimum section : 4mm2 (AWG10)
keep the cables of two poles +/- near (stranded if it’s possible) for to minimize the area of coil.
Page 224 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
23 Appendix G : Option “R” for safe disable function
23.1 Introduction
The drive ordered with “R” option are manufactured and validated to implement category 3
safety disable as described in EN 954-1 and EN 13849-1
By mean of this function it is possible to guarantee that unwanted restart of the motor
movements will not be allowed, even without using electromechanical switches between drive
and motor.
Drives labelled with “R” options are equipped of a electromechanical safety relay (certified by
TÜV institute). This relay, driven by user, turns off safely power semiconductor stage and gives
back a feedback though a free potential switch (normally closed).
The safe disable turns off the output power through an electromechanical action, independent
from drive firmware.
In TWIN-N drives both axes output power stages are switched off using a unique signal.
WARNING
The safe disable function prevent from torque generation in an squirrel cage induction motor
connected to the drive even if a drive fault does occur.
If a permanent magnet synchronous motor (brushless) is connected, a short rotation may occurs:
180° maximum, that becomes 90° maximum in case of salient poles technology motors.
Machines risk assessment activity must take care of this fact.
WARNING
The safe disable function do not provide an electrical shock prevention, so in case of service
activity on electrical connections, electrical power must be disconnected from drive and operator
must wait for the complete discharge of all internal capacitors (almost 6 minutes).
WARNING
The safe disable function inhibit the power stage of the drive including dynamic brake power
stage: for this reason when the safe disable signal is activated a fast emergency stop will not be
allowed.
Page 225 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
WARNING
The safe disable function guarantees machine safety only if it is correctly applied in the whole
machine safety plant.
The machine have to be verified through a risk assessment activity to be sure that the residual
risk of a dangerous event is compatible with risk class of the machine itself.
Safety related systems and plants have to be designed by people skilled and trained as required.
WARNING
The category 3 safety standstill function in compliance with EN954-1 and EN13849-1 standards,
is only guaranteed if all the feedback signals available from the drive (both hardware SCA/SCB
and software b41.5) are included in the machine / application safety system, accordingly to the
following instructions.
23.2 Signals description
On front side terminal box labelled with X5 following signals are connected:
• safety relay activation command on terminals 1 and 2 (labelled -SR and +SR)
• safety relay feedback switch contacts on terminals 3 and 4 (labelled SCA and SCB)
Terminal
block X5 pin
1-2
3-4
Signal
Description
Current
Safe disable
33mA ± 10%
command
(@ 24Vdc)
Feedback NC
max 1A
SC-A / SC-B
potential free switch
-SR / +SR
DC Voltage level
24Vdc ± 10% (relay on)
< 1V (relay off)
24Vdc ± 10%
–SR/+SR input is protected against wrong polarity connections.
When +24VDC voltage is applied to terminal +SR with respect to terminal SR-, switching ON
the safety relay, power supply to output power stage of the drive is present, so the motor
movements are not safely stopped. Under this condition the safety relay feedback switch, whose
contacts, are connected to terminals SCA and SCB and mechanically driven by relay mechanics,
is open.
This represent the working condition for drive and motor.
When power supply is disconnected from +SR and SR- terminals, switching OFF safety relay,
one of the relay switch cuts OFF power to drive output power stage driving circuits, disabling
output power stage. Under this condition the safety relay feedback switch, whose contacts, are
connected to terminals SCA and SCB and mechanically driven by relay mechanics, is closed.
A dedicated drive parameter (b41.5) shows the safety relay status output stages (drives) let it to
be an available information addressable over fieldbus communication or standard digital outputs
of the converter.
Using this kind of information will increase redundancy level of the safety chain, decreasing the
risk of human and equipment injury.
Page 226 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
Attention: both feedback have to be connected within the safety chain of the machine.
This issue must be considered: while switch feedback connected to terminals SCA and SCB is a
free potential switch driver directly by safety relay, so its work is independent from drive
firmware; feedback of parameter b41.5, otherwise, is implemented and used through drive
firmware functions.
The description above is summarized in following table:
safety relay
command
-SR / +SR
24V (relay ON)
0V (relay OFF)
Safety relay feedback
switch status
SCA / SCB
open
closed
Safety relay firmware Safety condition
against unwanted
feedback status
motor restarts
b41.5
1
No
0
Yes
23.3 Drive function blocks
SCA
SCB
+SR
- SR
b41.5
Page 227 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
23.4 Connections
The following diagrams show how to use the safe disable function. They should be considered as
a generic reference example. Any specific machine/application design must be analysed.
drive
analog or
field bus
control / supervisor
+SR
-SR
pnp output
I/O-GND
drive OK
(b41.4)
OUT0
0VQ
input
I/O-GND
feedback safety
relay
SC-A
SC-B
b41.5 feedback
OUT1
0VQ
Safety disable
input
I/O-GND
The risk of a short circuit between the safe disable wiring (-SR/+SR) and the 24V supply must be
minimized. Segregate the wiring in a dedicated raceway or use a shielded wire with grounded
shield.
23.5 Operation, sequence and timing
Follow the below stated sequence :
(✎)
1. Stop the motor in a controlled way (zero speed).
2. In case of vertical axes, activate the stationary brake against falling.
3. Disable the drives (b40.9=0) and verify that b41.12=0.
4. Activate the safe disable function by removing voltage at the input –SR/+SR
5. Verify the hardware feedback SCA/SCB (must be found close) and the software feedback
b41.5 (b41.5=0)
At this time, the category 3 safety standstill has been achieved without motor-side contactors.
The inverse sequence brings the drive to the standard operating condition.
Page 228 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
The timing is as follows :
b41.2
b40.9
-SR/+SR
SCA/SCB
(1) logic signals exchanged between drives and control/supervisor.
Warning :
in case of alarm (see appendix “Alarms”) during operation, the drive is automatically disabled.
Therefore the capability of stopping the motor in a controlled way is lost. The motor will stop
with its natural dynamic depending on the total inertia, friction and load torque. The same
happens if the safe disable function is activated before the motor has been stopped in a controlled
way.
Page 229 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
23.6 Example
The following diagram shows an example of safety disable and it is a general reference. Every
specific configuration of the machine must be verified in relation to the application.
23.7 Test and maintenance
The user must carry out a periodical functional test for the whole safety systems of the
machine/application. The functionality must specifically be verified at commissioning, after any
kind of maintenance operation on the machine (wiring, replacement of parts etc) and before any
potentially dangerous circumstance for personnel (need to access machine dangerous zones).
It must be verified that, using the safe disable function on each single drive unit, it is impossible
to move/rotate all the motors included in the machine safety system, and that this safe standstill
state is correctly detected through the feedback system from the drive unit (both hardware
feedback SCA/SCB and software feedback b41.5).
Page 230 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
24 Appendix H : retentive variable
The retentive variable are an optional hardware, that to be expressly requested when placing your
order (see “Identification”).
The retentive variable uses the pointer parameters from Pr310 to Pr325 (16word). Every pointer
corresponds to one variable, the value wrote or read coincides to one word. The variables are
saved cyclical in background, every 5/10ms (depends of actual operation, tmax= 3sec).
The system don’t execute any control of checksum parameters, but the user must generate a
procedure of check (important to check if the double word value is correct).
The bit b70.4 enable the save command into the retentive variable.
It’s possible to know when the background routine is finished (bit b70.5): set b70.5=1, when the
routine finishes this bit returns to 0.
End of
background
routine
b70.5=0
b70.4=1
b70.5=1
Attention: the pointer parameters are in common with the expansion board, the user must use the
different parameters for don’t compromise the value of retentive variable.
(✎)
Memory life if the drive is switched off: 10 years; max number of operation: 100.000, those are executed when the
drive is switched off or the supply is missing (if the save command is enabled).
b70.4
Pr310
Parameter number
(ex. Pr110)
Value of Pr110
Retentive variable
1
Save
Pr325
Parameter number
Pr310
Value of parameter
Retentive variable
16
Parameter number
Data recall
(at power up of the drive)
Retentive variable
Value of parameter
Page 231 of 233
Parker Hannifin S.p.A S.B.C. Division
Hi-drive User Manual
25 History of manual revisions
Any time the manual is updated, the new or modified parts are identified by a symbol (✎) beside
the text.
Rev. 0
November 2004
First edition: total pages: 150
Rev. 0.1
October 2005
Introduction of the product
HID35 and HID45
Programmable outputs adjourned
Rev. 0.2
December 2006
CANopen DSP402
HID75, 100 and 130: characteristics, dimensions, connections
Option “R”
External capacitor
Safety instructions
Identification
Motor with emergency brake
Phasing procedure for encoder with EnDat or Hiperface interface and motor
phases
Retentive variable
Pr51 and Pr53
EU standard 2002/96/EC
Rev. 0.3
February 2008
Encoder + Hall sensor, SinCos (one sin wave per pole pitch)
Encoder CAN
OPM122 and ramp with “S” profile
b40.11, Pr37, b41.14
Rev. 0.4
July 2008
Speed window: b40.7, b41.0, b41.1, b41.2, b41.3
b39.6, b39.12
Rev. 0.5
May 2009
Technical data: size 4/5
Parameters b39.6
Option “R”: relay status (par. 5)
Retentive variable: memory life
Rev. 0.6
April 2010
Hiperface cable, HALL sensor cable
HID155 and HID250
CANopen DS402: objects 0x2065, 0x2066 and bit b78.4
External capacitor per HID25: 4700µF
OPM122
For other informations log into website www.sbcelettronica.com. Arranges to the manual data can be made by the
manufacturer without advance notice. The data shown in the manual correspond to the specifications relating to the
revision date
Page 232