KEEX-2130
Industrial ECX Embedded SBC with Intel® Atom N270
User’s Guide
KEEX-2130 User’s Manual
I
Contact Info:
Quanmax Inc.
5F, No. 415, Ti-Ding Blvd. Sec. 2, NeiHu District,
Taipei, Taiwan 114
Tel: +886-2-2799-2789
Fax: +886-2-2799-7399
Visit our site at:
www.quanmax.com
© 2008 Quanmax Inc. All rights reserved.
The information in this user’s guide is provided for reference only. Quanmax does not assume any
liability arising out of the application or use of the information or products described herein. This user’s
guide may contain or reference information and products protected by copyrights or patents and does
not convey any license under the patent rights of Quanmax, nor the rights of others.
Quanmax is a registered trademark of Quanmax. All trademarks, registered trademarks, and trade
names used in this user’s guide are the property of their respective owners. All rights reserved. This
user’s guide contains information proprietary to Quanmax. Customers may reprint and use this user’s
guide in other publications. Customers may alter this user’s guide and publish it only after they remove
the Quanmax name, cover, and logo.
Quanmax reserves the right to make changes without notice in product or component design as
warranted by evolution in user needs or progress in engineering or manufacturing technology.
Changes which affect the operation of the unit will be documented in the next revision of this user’s
guide.
Revision
Date
Edited by
Changes
1.0
2/24/2010
Chris
Initial Release
1.1
4/2/2010
Zack
Update Pin Out Definitions –
LVDS/LAN/COM/Mini PCIE
KEEX-2130 User’s Manual
II
Content
Content
Content ..................................................................................................................................... 3 Figures ...................................................................................................................................... 4 Tables ........................................................................................................................................ 5 Safety Instructions................................................................................................................... 7 Before You Begin ................................................................................................. 7 When Working Inside a Computer .................................................................. 7 Preventing Electrostatic Discharge ................................................................... 8 Preface ..................................................................................................................................... 10 How to Use This Guide .................................................................................... 10 Unpacking .......................................................................................................... 10 Regulatory Compliance Statements ............................................................... 10 Warranty Policy ................................................................................................. 11 Maintaining Your Computer ........................................................................... 12 Chapter 1 Introduction ...................................................................................................... 15 Overview ............................................................................................................ 15 Product Specifications ...................................................................................... 16 System Block Diagram ..................................................................................... 17 Mechanical Dimensions ................................................................................... 18 Chapter 2 Hardware Settings ........................................................................................... 19 Overview ............................................................................................................ 19 Jumper Settings and Pin Definitions .............................................................. 20 Jumper Settings ................................................................................................. 21 Rear Panel Pin Assignments ............................................................................ 22 Main Board Pin Assignments .......................................................................... 24 Chapter 3 System Installation .......................................................................................... 31 Memory Module Installation .......................................................................... 31 Chapter 4 AMI BIOS Setup ............................................................................................... 33 Overview ............................................................................................................ 33 Main Menu ......................................................................................................... 34 Advanced Menu ................................................................................................ 35 Boot Menu .......................................................................................................... 39 Chipset Menu .................................................................................................... 40 Power Menu ....................................................................................................... 42 Security Menu .................................................................................................... 43 Exit Menu ........................................................................................................... 44 Chapter 5 Driver Installation ............................................................................................ 46 Appendix A Digital IO Sample Code ............................................................................ 47 Appendix B Watchdog Timer Sample Code ................................................................ 48 KEEX-2130 User’s Manual
3
Figures
Figures
Figure 1 Block Diagram ........................................................................................................ 17 Figure 2 Mechanical Dimensions ........................................................................................ 18 Figure 3 Jumper Connector ................................................................................................. 19 Figure 4 Jumper and Connector Locations ........................................................................ 20 Figure 5 Align the SO‐DIMM Memory Module with the onboard socket ................... 31 Figure 6 Press down on the SO‐DIMM Memory Module to lock it in place ................ 31 KEEX-2130 User’s Manual
4
Tables
Tables
Table 1 KEEX‐2130 Specification ......................................................................................... 16 Table 2 Jumper List ............................................................................................................... 21 Table 3 JP2, JP3:COM Port Signal / Power Selection ........................................................ 21 Table 4 JP1 Clear CMOS Selection ...................................................................................... 21 Table 5 JP5 Backlight Enable Selection ............................................................................... 21 Table 6 JP6 Blacklight & Panel Power Selection ................................................................ 22 Table 7 JP7 Power Mode Selection ...................................................................................... 22 Table 8 JP8 Mini‐PCIE Revision Selection ......................................................................... 22 Table 9 Rear Panel Connector List ...................................................................................... 22 Table 10 LAN1:10/100/1000 Ethernet RJ‐45 Connector(KEEX‐2130) ............................. 22 Table 11 J1:Audio phone jack(KEEX‐2131) ........................................................................ 23 Table 12 USB1,USB2:2‐Stack USB2.0 Type A Connector ................................................. 23 Table 13 COM1:RS‐232 Port 1 DB‐9 Connector ................................................................. 23 Table 14 VGA1:CRT DB‐15 Connector ............................................................................... 23 Table 15 Connector List ........................................................................................................ 24 Table 16 ATX1 +12V Power Input Connector .................................................................... 24 Table 17 JP1:Wireless LAN LED ......................................................................................... 24 Table 18 CN1:PS/2 KB/MS Output Wafer .......................................................................... 25 Table 19 CN2:Digital Input / Output Pin Header(KEEX‐2130) ...................................... 25 Table 20 CN2:Digital Input / Output Pin Header(KEEX‐2131) ...................................... 25 Table 21 CN3:VGA BOX HEADER ..................................................................................... 25 Table 22 CN4:LCD Inverter Output Wafer ........................................................................ 26 Table 23 DIMM1:DDR2 Memory SO‐DIMM Socket ........................................................ 26 Table 24 FP1:Front Panel 1 Pin Header .............................................................................. 26 Table 25 FP2:Front Panel 2 Pin Header .............................................................................. 26 Table 26 LVDS1:LVDS Panel Connector ............................................................................. 26 Table 27 AUDIO1:CD‐ROM Audio Input Wafer .............................................................. 27 Table 28 MPCIE1,MPCIE2:Mini PCIE slots ....................................................................... 27 Table 29 MPCIE3 SIM card Wafer ....................................................................................... 28 Table 30 USB3:USB2.0 Port 4, 5 Pin Header ...................................................................... 28 Table 31 CFD1:CF Type II Connector ................................................................................. 28 Table 32 SATA1:Serial ATA & HDD Power Connector .................................................... 29 Table 33 SATA2: SATA Connector ...................................................................................... 29 Table 34 AMP_R1:Audio AMP Right Output Wafer ........................................................ 29 KEEX-2130 User’s Manual
5
Tables
Table 35 AMP_L1:Audio AMP Left Output Wafer ........................................................... 29 Table 36 FAN1:FAN Wafer ................................................................................................... 29 Table 37 COM2:RS‐232 Port B Wafer .................................................................................. 30 Table 38 BIOS Main Menu ................................................................................................... 34 Table 39 IDE Device Setting Menu ..................................................................................... 34 Table 40 System Information ............................................................................................... 35 Table 41 Advanced Menu .................................................................................................... 35 Table 42 Onboard I/O Configuration ................................................................................. 36 Table 43 OnBoard Peripherals Configuration Settings .................................................... 37 Table 44 Hardware Health Configuration ......................................................................... 38 Table 45 Boot Menu ............................................................................................................... 39 Table 46 Chipset Menu ......................................................................................................... 40 Table 47 Video Function Configuration ............................................................................. 41 Table 48 Power Menu ......................................................................................................... 42 Table 49 Security Menu ........................................................................................................ 43 Table 50 Exit Menu ................................................................................................................ 44 KEEX-2130 User’s Manual
6
Safety Instructions
Safety Instructions
„ Before You Begin
Before handling the product, read the instructions and safety guidelines on the
following pages to prevent damage to the product and to ensure your own personal
safety. Refer to the “Advisories” section in the Preface for advisory conventions used
in this user’s guide, including the distinction between Warnings, Cautions, Important
Notes, and Notes.
„
„
Always use caution when handling/operating a computer. Only qualified,
experienced, authorized electronics service personnel should access the
interior of a computer. The power supplies produce high voltages and
energy hazards, which can cause bodily harm.
Use extreme caution when installing or removing components. Refer to the
installation instructions in this user’s guide for precautions and procedures.
If you have any questions, please contact Quanmax Post-Sales Technical
Support.
WARNING
High voltages are present inside the chassis when the unit’s power cord is
plugged into an electrical outlet. Turn off system power, turn off the power
supply, and then disconnect the power cord from its source before
removing the chassis cover. Turning off the system power switch does not
remove power to components.
„ When Working Inside a Computer
Before taking covers off a computer, perform the following steps:
1. Turn off the computer and any peripherals.
2. Disconnect the computer and peripherals from their power sources or
subsystems to prevent electric shock or system board damage. This does not
apply when hot swapping parts.
KEEX-2130 User’s Manual
7
Safety Instructions
3.
4.
Follow the guidelines provided in “Preventing Electrostatic Discharge” on the
following page.
Disconnect any telephone or telecommunications lines from the computer.
In addition, take note of these safety guidelines when appropriate:
„
„
To help avoid possible damage to system boards, wait five seconds after
turning off the computer before removing a component, removing a system
board, or disconnecting a peripheral device from the computer.
When you disconnect a cable, pull on its connector or on its strain-relief loop,
not on the cable itself. Some cables have a connector with locking tabs. If you
are disconnecting this type of cable, press in on the locking tabs before
disconnecting the cable. As you pull connectors apart, keep them evenly
aligned to avoid bending any connector pins. Also, before connecting a cable,
make sure both connectors are correctly oriented and aligned.
CAUTION
Do not attempt to service the system yourself except as explained in this
user’s guide. Follow installation and troubleshooting instructions closely.
„ Preventing Electrostatic Discharge
Static electricity can harm system boards. Perform service at an ESD workstation
and follow proper ESD procedure to reduce the risk of damage to components.
Quanmax strongly encourages you to follow proper ESD procedure, which can
include wrist straps and smocks, when servicing equipment.
You can also take the following steps to prevent damage from electrostatic
discharge (ESD):
„
„
When unpacking a static-sensitive component from its shipping carton, do not
remove the component’s antistatic packing material until you are ready to install
the component in a computer. Just before unwrapping the antistatic packaging,
be sure you are at an ESD workstation or grounded. This will discharge any
static electricity that may have built up in your body.
When transporting a sensitive component, first place it in an antistatic container
KEEX-2130 User’s Manual
8
Safety Instructions
„
„
„
or packaging.
Handle all sensitive components at an ESD workstation. If possible, use
antistatic floor pads and workbench pads.
Handle components and boards with care. Don’t touch the components or
contacts on a board. Hold a board by its edges or by its metal mounting bracket.
Do not handle or store system boards near strong electrostatic, electromagnetic,
magnetic, or radioactive fields.
KEEX-2130 User’s Manual
9
Preface
Preface
„ How to Use This Guide
This guide is designed to be used as step-by-step instructions for installation, and as
a reference for operation, troubleshooting, and upgrades.
NOTE
Driver downloads and additional information are available under
Downloads on our web site: www.quanmax.com.
„ Unpacking
When unpacking, follow these steps:
1.
2.
3.
After opening the box, save it and the packing material for possible future
shipment.
Remove all items from the box. If any items listed on the purchase order
are missing, notify Quanmax customer service immediately.
Inspect the product for damage. If there is damage, notify Quanmax
customer service immediately. Refer to “Warranty Policy” for the return
procedure.
„ Regulatory Compliance Statements
This section provides the FCC compliance statement for Class A devices.
FCC Compliance Statement for Class A Devices
The product(s) described in this user’s guide has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
KEEX-2130 User’s Manual
10
Preface
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the user’s guide, may cause harmful
interference to radio communications. Operation of this equipment in a residential
area (domestic environment) is likely to cause harmful interference, in which case
the user will be required to correct the interference (take adequate measures) at
their own expense.
Changes or modifications not expressly approved by Quanmax could void the user's
authority to operate the equipment.
NOTE
The assembler of a personal computer system may be required to test
the system and/or make necessary modifications if a system is found to
cause harmful interference or to be noncompliant with the appropriate
standards for its intended use.
„ Warranty Policy
Limited Warranty
Quanmax Inc.’s detailed Limited Warranty policy can be found under Support at
www.quanmax.com. Please consult your distributor for warranty verification.
The limited warranty is void if the product has been subjected to alteration, neglect,
misuse, or abuse; if any repairs have been attempted by anyone other than
Quanmax or its authorized agent; or if the failure is caused by accident, acts of God,
or other causes beyond the control of Quanmax or the manufacturer. Neglect,
misuse, and abuse shall include any installation, operation, or maintenance of the
product other than in accordance with the user’s guide.
No agent, dealer, distributor, service company, or other party is authorized to change,
modify, or extend the terms of this Limited Warranty in any manner whatsoever.
Quanmax reserves the right to make changes or improvements in any product
without incurring any obligation to similarly alter products previously purchased.
Return Procedure
For any Limited Warranty return, please contact Support at www.quanmax.com and
KEEX-2130 User’s Manual
11
Preface
login to obtain a Return Material Authorization (RMA) Number. If you do not have an
account, send an email to support@quanmax.com to apply for one.
All product(s) returned to Quanmax for service or credit must be accompanied by a
Return Material Authorization (RMA) Number. Freight on all returned items must be
prepaid by the customer who is responsible for any loss or damage caused by
common carrier in transit. Returns for Warranty must include a Failure Report for
each unit, by serial number(s), as well as a copy of the original invoice showing the
date of purchase.
To reduce risk of damage, returns of product must be in a Quanmax shipping
container. If the original container has been lost or damaged, new shipping
containers may be obtained from Quanmax Customer Service at a nominal cost.
Quanmax owns all parts removed from repaired products. Quanmax uses new and
reconditioned parts made by various manufacturers in performing warranty repairs
and building replacement products. If Quanmax repairs or replaces a product, its
warranty term is not extended.
Shipments not in compliance with this Limited Warranty Return Policy will not be
accepted by Quanmax.
Limitation of Liability
In no event shall Quanmax be liable for any defect in hardware, software, loss, or
inadequacy of data of any kind, or for any direct, indirect, incidental, or
consequential damages in connection with or arising out of the performance or use
of any product furnished hereunder. Quanmax’s liability shall in no event exceed the
purchase price of the product purchased hereunder. The foregoing limitation of
liability shall be equally applicable to any service provided by Quanmax or its
authorized agent.
„ Maintaining Your Computer
Environmental Factors
„
Temperature
The ambient temperature within an enclosure may be greater than room
ambient temperature. Installation in an enclosure should be such that the
amount of air flow required for safe operation is not compromised.
Consideration should be given to the maximum rated ambient temperature.
Overheating can cause a variety of problems, including premature aging and
failure of chips or mechanical failure of devices.
KEEX-2130 User’s Manual
12
Preface
If the system has been exposed to abnormally cold temperatures, allow a
two-hour warm-up period to bring it up to normal operating temperature before
turning it on. Failure to do so may cause damage to internal components,
particularly the hard disk drive.
„
Humidity
High-humidity can cause moisture to enter and accumulate in the system. This
moisture can cause corrosion of internal components and degrade such
properties as electrical resistance and thermal conductivity. Extreme moisture
buildup inside the system can result in electrical shorts, which can cause
serious damage to the system.
Buildings in which climate is controlled usually maintain an acceptable level of
humidity for system equipment. However, if a system is located in an unusually
humid location, a dehumidifier can be used to maintain the humidity within an
acceptable range. Refer to the “Specifications” section of this user’s guide for
the operating and storage humidity specifications.
„
Altitude
Operating a system at a high altitude (low pressure) reduces the efficiency of
the cooling fans to cool the system. This can cause electrical problems related
to arcing and corona effects. This condition can also cause sealed components
with internal pressure, such as electrolytic capacitors, to fail or perform at
reduced efficiency.
Power Protection
The greatest threats to a system’s supply of power are power loss, power spikes,
and power surges caused by electrical storms, which interrupt system operation
and/or damage system components. To protect your system, always properly
ground power cables and one of the following devices.
„
Surge Protector
Surge protectors are available in a variety of types and usually provide a level
of protection proportional with the cost of the device. Surge protectors prevent
voltage spikes from entering a system through the AC power cord. Surge
protectors, however, do not offer protection against brownouts, which occur
when the voltage drops more than 20 percent below the normal AC line voltage
level.
KEEX-2130 User’s Manual
13
Preface
„
Line Conditioner
Line conditioners go beyond the overvoltage protection of surge protectors.
Line conditioners keep a system’s AC power source voltage at a fairly constant
level and, therefore, can handle brownouts. Because of this added protection,
line conditioners cost more than surge protectors. However, line conditioners
cannot protect against a complete loss of power.
„
Uninterruptible Power Supply
Uninterruptible power supply (UPS) systems offer the most complete protection
against variations on power because they use battery power to keep the server
running when AC power is lost. The battery is charged by the AC power while it
is available, so when AC power is lost, the battery can provide power to the
system for a limited amount of time, depending on the UPS system.
UPS systems range in price from a few hundred dollars to several thousand
dollars, with the more expensive unit s allowing you to run larger systems for a
longer period of time when AC power is lost. UPS systems that provide only 5
minutes of battery power let you conduct an orderly shutdown of the system,
but are not intended to provide continued operation. Surge protectors should be
used with all UPS systems, and the UPS system should be Underwriters
Laboratories (UL) safety approved.
KEEX-2130 User’s Manual
14
Chapter 1
Chapter 1
Introduction
„ Overview
The KEEX-2130 is an ECX Form Factor embedded single board computer (SBC)
that combines the high performance and low power consumption of the Intel®
Atom™ processor with Intel® 945GSE/ ICH7M chipset and supports DDR2 400/533
SODIMM up to 2GB. This SBC offers the latest performance, features and I/O
interfaces at an extremely attractive price/performance ratio and measures 105mm
x 146mm, a 75 percent space reduction over micro-ATX boards. The KEEX-2130
features VGA and 18/24-bit dual channel LVDS panel support, SATA,
RS-232/422/485 serial port, Digital I/O, Gb/s Ethernet, USB 2.0, keyboard/mouse,
and HD audio.
Checklist
„
„
„
„
„
SATA cable
Y cable for keyboard & mouse
Driver/ Manual CD
Quick Installation Guide
KEEX-2130 ECX motherboard
Features
„
„
„
„
„
„
„
Intel® Atom Processor N270
Intel® 945GSE / ICH7-M
DDR2 SO-DIMM Socket, total up to 2 GB
SATA, CompactFlash socket,
2x mini PCIe, SIM card supported for GPRS/3G module
Gb/s Ethernet, 8x USB 2.0 ports, 2x COM, VGA, 24-bits LVDS
Watchdog Timer, Hardware Monitor
KEEX-2130 User’s Manual
15
Chapter 1
„ Product Specifications
CPU Support
Intel® Atom™ N270
Chipset
Intel® 945GSE + ICH7-M
Memory
1x DDR2 400/533 SO-DIMM Socket, up to 2GB
BIOS
AMI Plug & Play BIOS – 8Mb SPI ROM
Integrated on Intel® 945GSE Chipset
Display
18/24-bit Dual channel LVDS support
1x VGA
LAN
Audio
1x RJ-45, Gigabit Ethernet
HD Codec ALC662 with 2W Audio Amplifier
Supports Line-in, Line-out & Microphone
2x SATA (one with onboard power connector)
Peripheral
Support
1x CompactFlash socket
8x USB 2.0
2x COMs with Power Selection
4x DI/DO
Power
Connector
Expansion
Watchdog
Timer
Hardware
Monitor
Dimensions
Environmental
Factors
Certifications
ATX-4P
Two MiniPCI Express socket
1-255 step
Operating voltage, CPU temperature and fan speed
ECX Embedded Board (105 x 146 mm)
Operation Temp: 0ºC - 60ºC
Storage Temp.: -10ºC - 85ºC
Humidity: 0% - 90%
CE, FCC Class A
Table 2 KEEX-2130 Specification
KEEX-2130 User’s Manual
16
Chapter 1
„ System Block Diagram
Figure 1 Block Diagram
KEEX-2130 User’s Manual
17
Chapter 1
„ Mechanical Dimensions
Figure 2 Mechanical Dimensions
KEEX-2130 User’s Manual
18
Chapter 2
Chapter 2
Hardware Settings
„ Overview
This chapter provides the definitions and locations of jumpers, headers, and
connectors.
Jumpers
The product has several jumpers which must be properly configured to ensure
correct operation.
Figure 3 Jumper Connector
For a three-pin jumper (see figure above), the jumper setting is designated “1-2”
when the jumper connects pins 1 and 2. The jumper setting is designated “2-3”
when pins 2 and 3 are connected and so on. You will see that one of the lines
surrounding a jumper pin is thick, which indicates pin No.1.
To move a jumper from one position to another, use needle-nose pliers or tweezers
to pull the pin cap off the pins and move it to the desired position.
KEEX-2130 User’s Manual
19
Chapter 2
„ Jumper Settings and Pin Definitions
For jumper and connector locations, please refer to the diagrams below.
Figure 4 Jumper and Connector Locations
KEEX-2130 User’s Manual
20
Chapter 2
Jumper Settings
To ensure correct system configuration, the following section describes how to set
the jumpers to enable/disable or change functions. For jumper descriptions, please
refer to the table below.
Label
JP2
JP3
JP4
JP5
JP6
JP7
JP8
Table 2 Jumper List
Function
COM1 Signal / Power Selection
COM2 Signal / Power Selection
Clear CMOS Selection
Backlight Enable Selection
Backlight & Panel Power Selection
AT/ATX Power Mode Selection
Mini-PCIE Revision Selection
Table 3 JP2, JP3:COM Port Signal / Power Selection
Jumper
Setting
1
1-3 Short
3-5 Short
5-7 Short
7-9 Short
2-4 Short
4-6 Short
6-8 Short
8-10 Short
2
Function
Pin 1 = +12V
Pin 1 = +5V
Pin 1 = +5V
Pin 1 = DCD@RS232, TX+@RS422,
RTX+@RS485
Pin 8/9 = +12V
Pin 8/9 = +5V
Pin 8/9 = +5V
Pin 8/9 = RI
DIP 10P 2R MALE STRAIGHT TYPE Pitch:2.54mm [YIMTEX 3322*05SAGR(6T)]
1
2
Table 4 JP3: Clear CMOS Selection
Jumper
Status
Open
Normal Operation
Short
Clear CMOS
Pitch:2.54mm [YIMTEX 3321*02SAGR(6T)]
Table 5 JP5:Backlight Enable Selection
Jumper
Status
1
1-2
Active High
2
3
2-3
Active Low
Pitch:2.0mm [YIMTEX 3291*03SAGR(6T)]
KEEX-2130 User’s Manual
21
Chapter 2
Table 6 JP6:Blacklight & Panel Power Selection
1
Jumper
2
1
5
6
2
Setting
1-3
3-5
2-4
4-6
Status
Backlight Power = +12V
Backlight Power = +5V
Panel Power = +3.3V
Panel Power = +5V
Pitch:2.54mm [YIMTEX 3362*03SAGR]
1
2
Table 7 JP7:Power Mode Selection
Jumper
Status
Open
ATX Mode
Short
AT Mode
Pitch:2.54mm [YIMTEX 3321*02SAGR(6T)]
Table 8 JP8:Mini-PCIE Revision Selection
Jumper
Status
1
1-2
V1.1
2
2-3
V1.2
3
Pitch:2.0mm [YIMTEX 3291*03SAGR(6T)]
Rear Panel Pin Assignments
Table 9 Rear Panel Connector List
Label
Function
LAN1
10/100/1000 Ethernet RJ-45 Connector
USB1
USB2.0 Port 2 , 3 Type A Connector
USB2
USB2.0 Port 2 , 3 Type A Connector
COM1
RS-232 Port A DB-9 Connector
VGA1
VGA DB-15 Connector
Table 10 LAN1:10/100/1000 Ethernet RJ-45 Connector (KEEX-2130)
Pin
1
3
5
7
Signal Name
MDI 0+
MDI 1+
MDI 2+
MDI 3+
LAN LED
Yellow
OFF / GREEN / ORANGE
Pin
2
4
6
8
Signal Name
MDI 0MDI 1MDI 2MDI 3-
Function
LINK / ACTIVE
10 / 100 / 1000(Speed)
RJ45+TFM+LED 10/100/1000 14P DIP 90° [UDE RT7-174AAM1A(XA)]
KEEX-2130 User’s Manual
22
Chapter 2
Table 11 J1:Audio phone jack(KEEX-2131)
Pin
1
2
3
4
5
Signal
GND
L_OUT_L
GND
L_OUT_R
NC
JACK DIP 5 PIN,GREEN [KUON YI PJ-2508PC-5-L]
Table 12 USB1,USB2: 2-Stack USB2.0 Type A Connector
Pin
1
2
3
4
Signal Name
+5V
USB1USB1+
GND
Pin
5
6
7
8
Signal Name
+5V
USB0USB0+
GND
USB DIP 4*2P 90D [FOXCONN UB11123-8D1-4F]
Table 13 COM1: RS-232 Port 1 DB-9 Connector
Pi
Half Duplex Full Duplex
RS-232
RS-422
n
RS-485
RS-485
1
DCD
TX-
DATA-
TX-
2
RXD
RX+
NA
RX+
3
TXD
TX+
DATA+
TX+
4
DTR
RX-
NA
RX-
5
GND
GND
GND
GND
6
DSR
NA
NA
NA
7
RTS
NA
NA
NA
8
CTS
NA
NA
NA
9
+5V/+12V/R
I
+5V/+12V/N
A
+5V/+12V/N
A
+5V/+12V/N
A
9Pin 90 度 Color:Green/for PC99 W/SCREW 螺帽=4.8mm,螺絲總長=9.5mm [芬瑩
SM1001P01012PN]
Note 1:RS-232 / 422 / 485 can be selected in BIOS setup.
Table 14 VGA1:CRT DB-15 Connector
Signal Name
Red
Blue
GND
GND
VCC
NC
HSYNC
DDC clock
Pin
1
3
5
7
9
11
13
15
Pin
2
4
6
8
10
12
14
Signal Name
Green
NC
GND
GND
GND
DDC data
VSYNC
D-SUB 15P DIP (F) 90D H/D CONNECTOR Blue 附六角螺絲 [芬瑩 SM1003S01012PN]
KEEX-2130 User’s Manual
23
Chapter 2
Main Board Pin Assignments
Table 15 Connector List
Function
+12V Power Input Connector
Wireless LAN LED
PS/2 KB/MS Output Wafer
Digital Input / Output Box Header
VGA Box Header
LCD Inverter Output Wafer
DDR2 Memory SO-DIMM Socket
Front Panel 1 Pin Header
Front Panel 2 Pin Header
LVDS Panel Connector
CD-ROM Audio Input Wafer
Mini PCIE slots
Mini PCIE slots
USB2.0 Port 4, 5 Pin Header
CF Type II Connector
Serial ATA & HDD Power Connector
Serial ATA Connector
Audio AMP Right Output Wafer
(KEEX-2130 Only)
Audio AMP Left Output Wafer
(KEEX-2130 Only)
System FAN Wafer
RS-232 Port B With Power Wafer
Label
ATX1
JP1
CN1
CN2
CN3
CN4
DIMM1
FP1
FP2
LVDS1
AUDIO1
MPCIE1
MPCIE2
USB3
CFD1
SATA1
SATA2
AMP_R1
AMP_L1
FAN1
COM2
Connector Pin Assignment
Table 16 ATX1:+12V Power Input Connector
Pin
Signal Name
1
GND
2
GND
3
+12V
4
+12V
Pitch:4.2mm 空心 PIN [YIMTEX 576MWA2*02STR]
1
2
Table 17 JP1:Wireless LAN LED
Jumper
Status
1
+3.3VSB
2
LED_WLAN#
Pitch:2.54mm [YIMTEX 3321*02SAGR(6T)]
KEEX-2130 User’s Manual
24
Chapter 2
Table 18 CN1:PS/2 KB/MS Output Wafer
Pin
1
2
3
4
5
6
Signal Name
MSCLK
VCC
MSDAT*
KBDAT
GND
KBCLK
Pitch=2.0mm 6P MALE 1R 180D [STM M24266]
Table 19 CN2:Digital Input / Output Pin Header(KEEX-2130)
1
2
9
10
Pin
1
3
5
7
9
Signal
Digital Output 0
Digital Output 1
Digital Output 2
Digital Output 3
+5V
Pin
2
4
6
8
10
Signal
Digital Input 0
Digital Input 1
Digital Input 2
Digital Input 3
GND
DIP 10P 2R MALE STRAIGHT TYPE Pitch:2.54mm [YIMTEX 3322*05SAGR(6T)]
Table 20 CN2:Digital Input / Output Pin Header(KEEX-2131)
Pin
1
3
5
7
9
Signal
Digital Output 0
Digital Output 1
Digital Output 2
Digital Output 3
+5V
Pin
2
4
6
8
10
Signal
Digital Input 0
Digital Input 1
Digital Input 2
Digital Input 3
GND
Pitch:2.54mm 10P 2R MALE 180° 牛角[PINREX 51F-70-10GB01]
Table 21 CN3 VGA BOX HEADER
Pin
Signal
Pin
Signal
1
3
RR
BB
2
4
GG
GND
5
7
9
GND
GND
VGAPWR
6
8
10
VGAPWR
GND
GND
11
GND
12
SD_DATA
13
15
VGA_HSYNC
SD_CLK
14
16
VGA_VSYNC
GND
Pitch:2.0mm DIP 16P 2R 180D [PINREX 52S-90-16GB00]
KEEX-2130 User’s Manual
25
Chapter 2
Table 22 CN4:LCD Inverter Output Wafer
Pin
1
2
3
4
5
6
7
Signal Name
NC
BL_ADJ
GND
+5V / +12V **
+5V / +12V **
GND
BL_EN / BL_EN# *
Pitch:1.25mm 7P 90D WAFER [YIMTEX 501MW1*07MTRR]
* : Selected by JP5.
** : Selected by JP6.
Table 23 DIMM1:DDR2 Memory SO-DIMM Socket
SO DIMM 200P DDR2 1.8V H:6.5mm STD TYPE [FOXCONN AS0A426-N6SN-4F ]
Table 24 FP1:Front Panel 1 Pin Header
RSTBTN
HLED
+ 1
2 +
-
SPKR
+
7
-
8
-
Pin
1
3
5
7
Signal
Reset Button +
Reset Button HDD LED +
HDD LED -
Pin
2
4
6
8
Signal
Speaker +
NC
NC
Speaker -
Pitch:2.54mm [YIMTEX 3322*04SAGR(6T)]
Table 25 FP2:Front Panel 2 Pin Header
+ 1
PLED
2 +
-
PWRBTN
KLOCK
SMD
+
-
9
10 SMC
Pin
1
3
5
7
9
Signal
Power LED +
NC
Power LED Keyboard Lock
GND
Pin
2
4
6
8
10
Signal
Power Button +
Power Button NC
SMBus Data
SMBus Clock
DIP 10P 2R MALE STRAIGHT TYPE Pitch:2.54mm [YIMTEX 3322*05SAGR(6T)]
Table 26 LVDS1:LVDS Panel Connector
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
KEEX-2130 User’s Manual
Signal Name
LVDS_A0LVDS_A0+
LVDS_A1LVDS_A1+
LVDS_A2LVDS_A2+
GND
LVDS_ACLKLVDS_ACLK+
LVDS_A3-/NC
LVDS_A3+/NC
LVDS_B0LVDS_B0+
GND
26
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Signal Name
LVDS_B1+
GND
LVDS_B2LVDS_B2+
LVDSBCLKLVDS_BCLK+
LVDS_B3-/NC
LVDS_B3+/NC
GND
JILI_DAT
VDDEN
JILI_CLK
+3.3V / +5V *
+3.3V / +5V *
Chapter 2
15
LVDS_B1-
30
+3.3V / +5V *
Pitch:1mm 30P 90° 1R [JAE FI-X30SSL-HF]
Table 27 AUDIO1:CD-ROM Audio Input Wafer
Pin
Signal Name
1
LOUT_R
2
AUG(GND)
3
LOUT_L
4
LIN_R
5
MIC
6
LIN_L
Pitch:2.5mm DIP 6P 180° WAFER [YIMTEX 510XW1*06STR]
Table 28 MPCIE1,MPCIE2:Mini PCIE slots
Signal Name
PCIE_WAKE#
NC
NC
NC
GND
CLK100_MPCIE1#/2
#
CLK100_MPCIE1/2
GND
NC
NC
GND
PCIE_RX2-/3PCIE_RX2+/3+
GND
GND
PCIE_TX2-/3PCIE_TX2+/3+
GND
GND
+3.3VSB
+3.3VSB
GND
NC
NC
NC
NC
Pin
1
3
5
7
9
Pin
2
4
6
8
10
Signal Name
+3.3VSB
GND
+1.5V
*UIM_PWR/NC
*UIM_DATA/NC
11
12
*UIM_CLK/NC
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
*UIM_RESET/NC
*UIM_VPP/NC
GND
MPCIE1/2_EN
RST_PCIE#
+3.3VSB
GND
+1.5V
SB_SMB_CLK
SB_SMB_DAT
GND
USB6N/7N
USB6P/7P
GND
LED_WLAN#
LED_WLAN#
LED_WLAN#
+1.5v
GND
+3.3VSB
SMD PCIE 52P 90D(F) MINI PCI-Express Connector [FOXCONN AS0B226-S56N-7F]
SMD COLUMN M2.5 THREADS C.L=4.5mm STANDOFF=3mm [湘鏵 BOB398.0BM]
KEEX-2130 User’s Manual
27
Chapter 2
Table 29 MPCIE3 SIM card Wafer
Pin
1
2
3
4
5
6
Signal Name
UIM_PWR
UIM_VPP
UIM_DATA
UIM_CLK
UIM_RESET
GND
P-1.25mm WAFER [Pinrex 712-73-06TWE0]
Table 30 USB3:USB2.0 Port 4, 5 Pin Header
1
2
3
4
5
6
7
8
10
Pin
1
3
5
7
9
Signal Name
+5V
USB4USB4+
GND
KEY
Pin
2
4
6
8
10
Signal Name
+5V
USB5USB5+
GND
GND
Pitch:2.54mm(將 YIMTEX 3322*05SAGR(6T)第 9 pin 抽掉)[YIMTEX 3322*05SAGR(6T) -09]
Table 31 CFD1: CF Type II Connector
Signal Name
GND
IDE Data 3
IDE Data 4
IDE Data 5
IDE Data 6
IDE Data 7
IDE Chip select 1#
GND
GND
GND
GND
GND
+5V
GND
GND
GND
GND
SDA2
IDE Address 1
IDE Address 0
IDE Data 0
IDE Data 1
IDE Data 2
IOIS16#
GND
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Pin
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Signal Name
GND
IDE Data 11
IDE Data 12
IDE Data 13
IDE Data 14
IDE Data 15
IDE Chip select 3#
GND
IDEIOR#
IDEIOW#
+5V
IDEIRQ
+5V
PCSEL
NC
Reset IDE
IDEIORDY
DREQ
DACK#
IDE activity
PDIAG#
IDE Data 8
IDE Data 9
IDE Data 10
GND
CF SMD MALE 50P90D 2R stand-off 2mm, Standard type[晉祥 CF1A-71041-00E01]
KEEX-2130 User’s Manual
28
Chapter 2
Table 32 SATA1: Serial ATA & HDD Power Connector
Pin
S1
S2
S3
S4
S5
S6
S7
P1
P2
P3
P4
Signal Name
GND
TX+
TXGND
RXRX+
GND
+3.3V
+3.3V
+3.3V
GND
Pin
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
Signal Name
GND
GND
+5V
+5V
+5V
GND
GND
GND
+12V
+12V
+12V
DIP 7P+15P MALE 180D SATA CONNECTOR BLACK [WIN WIN WATH-22DLBGU4]
Table 33 SATA2: SATA Connector
Pin
Signal Name
1
GND
2
TX+
3
TX4
GND
5
RX6
RX+
7
GND
DIP 7P 180D SATA CONNECTOR BLUE [FOXCONN LD1807V-S52U]
Table 34 AMP_R1: Audio AMP Right Output Wafer
Pin
Signal Name
1
Speaker+
2
SpeakerPitch=2.0mm 2P 180° WAFER [YIMTEX 503PW1*02STR]
Table 35 AMP_L1: Audio AMP Left Output Wafer
Pin
Signal Name
1
Speaker+
2
SpeakerPitch=2.0mm 2P 180° WAFER [YIMTEX 503PW1*02STR]
1
2
3
Table 36 FAN1:FAN Wafer
Pin
Signal
1
GND
2
+12V
3
FAN_RPM
Pitch:2.54mm WAFER [YIMTEX 521AW1*03STR]
KEEX-2130 User’s Manual
29
Chapter 2
Pin
Table 37 COM2: RS-232 Port B Wafer
Half Duplex Full Duplex
RS-232
RS-422
RS-485
RS-485
1
DCD
TX-
DATA-
TX-
2
DSR
NA
NA
NA
3
RXD
RX+
NA
RX+
4
RTS
NA
NA
NA
5
TXD
TX+
DATA+
TX+
6
CTS
NA
NA
NA
7
DTR
RX-
NA
RX-
8
+5V/+12V/RI +5V/+12V/NA +5V/+12V/NA +5V/+12V/NA
9
GND
GND
GND
GND
10
+5V
+5V
+5V
+5V
Pitch:1.54mm WAFER [YIMTEX 501MW1*10STR]
COM Port Cable 0C5019001000010L COM Port cable, 10-pin pitch=1.25mm to
DB-9 connector, L=10cm
Note 1:RS-232 / 422 / 485 can be selected in BIOS setup.
Note 2:The function of pin 8 can be selected by JP3 (in BIOS setup)
KEEX-2130 User’s Manual
30
Chapter 2
Chapter 3
System Installation
„ Memory Module Installation
Carefully follow the steps below in order to install the DIMMs:
1.
2.
3.
To avoid generating static electricity and damaging the SO-DIMM, ground
yourself by touching a grounded metal surface or use a ground strap before you
touch the SO-DIMM.
Do not touch the connectors of the SO-DIMM. Dirt or other residue may cause a
malfunction.
Hold the SO-DIMM with its notch aligned with the memory socket of the board
and insert it at a 30-degree angle into the socket.
Figure 5 Align the SO-DIMM Memory Module with the onboard socket
4.
5.
Fully insert the module into the socket until a “click” is heard.
Press down on the SO-DIMM so that the tabs of the socket lock on both sides
of the module
Figure 6 Press down on the SO-DIMM Memory Module to lock it in place
KEEX-2130 User’s Manual
31
Chapter 2
Removing a DIMM:
To remove the SO-DIMM, use your fingers or a small screwdriver to carefully push
away the tabs that secure either side of the SO-DIMM. Lift it out of the socket.
Make sure you store the SO-DIMM in an anti-static bag. The socket must be
populated with memory modules of the same size and manufacturer.
KEEX-2130 User’s Manual
32
Chapter 4
Chapter 4
AMI BIOS Setup
„ Overview
This chapter provides a description of the AMI BIOS. The BIOS setup menus and
available selections may vary from those of your product. For specific information on
the BIOS for your product, please contact Quanmax.
NOTE: The BIOS menus and selections for your product may vary from
those in this chapter. For the BIOS manual specific to your product, please
contact Quanmax
AMI's ROM BIOS provides a built-in Setup program, which allows the user to modify
the basic system configuration and hardware parameters. The modified data will
be stored in a battery-backed CMOS, so that data will be retained even when the
power is turned off. In general, the information saved in the CMOS RAM will not
need to be changed unless there is a configuration change in the system, such as a
hard drive replacement or when a device is added.
It is possible for the CMOS battery to fail, which will cause data loss in the CMOS
only. If this happens you will need to reconfigure your BIOS settings.
KEEX-2130 User’s Manual
33
Chapter 4
„ Main Menu
The BIOS Setup is accessed by pressing the DEL key after the Power-On Self-Test
(POST) memory test begins and before the operating system boot begins. Once you
enter the BIOS Setup Utility, the Main Menu will appear on the screen. The Main
Menu provides System Overview information and allows you to set the System Time
and Date. Use the “<” and “>” cursor keys to navigate between menu screens.
Table 38 BIOS Main Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Chipset
System Date
System Time
Power
[Mon 01/21/2008]
[10:18:15]
> SATA 1
:[Not Detected]
> CF
:[Not Detected]
Exit
Use [ENTER], [TAB]
or [SHIFT-TAB] to
select a field.
Use [+] or [-] to
configure system Time.
:[Not Detected]
> SATA 2
Security
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
> System Information
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Below table is described for SATA 1, SATA 2, CF setting.
Table 39 IDE Device Setting Menu
BIOS SETUP UTILITY
Main
Advanced
Primary Master
Device
Boot
Chipset
Security
[Auto]
[Auto]
[Auto]
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
LBA/ Large Mode
KEEX-2130 User’s Manual
Exit
Disable: Disables LBA Mode.
Auto: Enables LBA Mode if the
device supports it and the
device is not already formatted
with LBA Mode disabled.
:Not Detected
LBA/ Large Mode
DMA Mode
S.M.A.R.T
Power
34
Chapter 4
Enables or disables the LBA (Logical Block Addressing)/ Large mode. Setting to
Auto enables the LBA mode if the device supports this mode, and if the device was
not previously formatted with LBA mode disabled. Options: Disabled, Auto
DMA Mode
Options: Auto, SWDMA, MWDMA, UDMA mode
S.M.A.R.T
SMART stands for Smart Monitoring, Analysis, and Reporting Technology. It allows
AMIBIOS to use the SMART protocol to report server system information over a
network. Options: Auto, Disabled, Enabled
Table 40 System Information
BIOS SETUP UTILITY
Main
Advanced
AMIBIOS
Version
Build Date:
Boot
Chipset
Power
Security
Exit
: 1.1
:02/09/10
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
Processor
Genuine Intel® CPU N270
@ 1.60GHz
Speed
:1600MHz
Count
:1
System Memory
Size
:1016MB
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
„ Advanced Menu
Table 41 Advanced Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Chipset
Power
Security
Advanced Settings
Warning:
Setting wrong values in below sections
may cause system to malfunction.
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
> I/O Configuration
> OnBoard Peripherals Configuration
> Hardware Health Configuration
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Press <Enter> to select a sub-menu for detailed options.
KEEX-2130 User’s Manual
35
Exit
Chapter 4
Table 42 Onboard I/O Configuration
BIOS SETUP UTILITY
Main
Advanced
Boot
Onboard I/O Configuration
COM1 Address
COM1 Mode
COM1 Function Type
COM2 Address
COM2 Mode
COM2 Function Type
Chipset
Power
Security
Allow BIOS to Select Serial
Port1 Base Address.
[3F8/IRQ4]
[Normal]
[RS232]
[2F8]
[Normal]
[RS232]
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
COM1 Address
Options: Disabled, 3F8/IRQ4, 3E8/IRQ4, 2E8/IRQ3
COM1 Mode
Options: Normal, IrDA, ASK IR
COM1 Function Type
Options: RS232, RS422, RS485
COM2 Address
Options: Disabled, 3F8/IRQ4, 3E8/IRQ4, 2E8/IRQ3
COM 2 Mode
Options: Normal, IrDA, ASK IR
COM2 Function Type
Options: RS232, RS422, RS485
KEEX-2130 User’s Manual
Exit
36
Chapter 4
Table 43 OnBoard Peripherals Configuration Settings
BIOS SETUP UTILITY
Main
Advanced
Boot
OnBoard Peripherals Configuration Settings
USB Controller
USB 2.0 Controller
USB Device Legacy Support
Audio Controller
Onboard LAN Controller
Onboard LAN OPTROM
Chipset
Power
Security
Options
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Disabled]
Disabled
Enabled
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
USB Controller
Options: Enabled, Disabled
USB 2.0 Controller
Options: Enabled, Disabled
USB Device Legacy Support
Options: Enabled, Disabled, Auto
Audio Controller
Options: Enabled, Disabled
Onboard LAN Controller
Options: Enabled, Disabled
Onboard LAN OPTROM
Options: Enabled, Disabled
KEEX-2130 User’s Manual
37
Exit
Chapter 4
Table 44 Hardware Health Configuration
BIOS SETUP UTILITY
Main
Advanced
Hardware Health Configuration
CPU Warning Temperature
CPU Shutdown Temperature
CPU Temperature
SYS Temperature
FAN 1 Mode Setting
Fan Speed
+VCORE
+1.05V
+3.3V
+5V
+12V
+1.8v
+VCC RTC
Boot
Chipset
Power
Security
[Disabled]
[Disabled]
:52°C/ 192°F
:42°C/ 129°F
[Full On mode]
:N/A
:1.072 V
:1.040 V
:3.312 V
:5.053 V
:11.840 V
:1.758 V
:3.365 V
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
KEEX-2130 User’s Manual
38
Exit
Chapter 4
„ Boot Menu
Table 45 Boot Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Chipset
Power
Boot Settings
> Quick Boot
> Bootup Num-Lock
> Wait For ’F1’ If Error
> Hit ’DEL’Message Display
[Enabled]
[ON]
[Enabled]
[Enabled]
Security
Exit
Allow BIOS to Skip certain
tests while booting. This
will decrease the time
needed to boot the
system.
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Quick Boot
Enabling this item allows BIOS to skip some Power On Self Tests (POST) while
booting to decrease the time needed to boot the system. When set to [Disabled],
BIOS performs all the POST items.
Options: Disabled, Enabled
Bootup Num-Lock [On]
Allow you to select the power-on state for the NumLock.
Options: Off, On
Wait for ‘F1’ If Error [Enabled]
When set to Enabled, the system waits for F1 key to be pressed when error occurs.
Options: Disabled, Enabled
Hit ‘DEL’ Message Display [Enabled]
When set to Enabled, the system displays the message ‘Press DEL to run Setup’
during POST.
Options: Disabled, Enabled
KEEX-2130 User’s Manual
39
Chapter 4
„ Chipset Menu
Table 46 Chipset Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Chipset Settings
DRAM Frequency
Configure DRAM Timing by SPD
Boots Graphic Adapter Priority
Internal Graphics Mode Select
Hyper Threading Technology
Chipset
Power
Security
Exit
Options
[Auto]
[Enabled]
[PEG/PCI]
[Enabled, 8MB]
[Enabled]
> Video Function Configuration
Auto
400 MHz
533 MHz
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
DRAM Frequency
Options: Auto, 400 MHz, 533MHz
Configure DRAM Timing by SPD
Options: Disabled, Enabled
Boots Graphic Adapter Priority
Select which graphics controller to use as the primary boot device.
Options: IGD, PCI/IGD, PCI/PEG, PEG/IGD, PEG/PCI
Internal Graphics Mode Select
Select the amount of system memory used by the Internal graphics device.
Options: Disabled, Enabled 1MB, Enabled 8M
Hyper Threading Technology
Options: Disabled, Enabled
KEEX-2130 User’s Manual
40
Chapter 4
Video Function Configuration
Table 47 Video Function Configuration
BIOS SETUP UTILITY
Main
Advanced
Boot
Power
Chipset
Security
Options
Video Function Configuration
DVMT Mode Select
DVMT/FIXED Memory
[DVMT Mode]
[128M]
Boot Display Device
Flat Panel Type
Local Flat Panel Scaling
Panel BackLight Voltage
[Auto]
[1024X768
[Auto]
[2.5]
Fixed Mode
DVMT Mode
Combo Mode
24Bit 1C]
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
DVMT Mode Select [DVMT Mode]
Options: Fixed Mode, DVMT Mode, Combo Mode
DVMT/FIXED Memory [128MB]
Options: 64MB, 128MB, Maximum DVMT
Boot Display Device [VGA]
Options: VGA, LVDS, VGA+LVDS
Flat Panel Type [1024x768 24Bit 2C]
Options:
1024x768
24Bit 1CH
1280x1024
24Bit 1CH
1366x768
24Bit 2CH
1920x1080
24Bit 2CH
Local Flat Panel Scaling [Auto]
Options: Auto, Forced Scaling, Disabled
Panel BackLight Voltage [2.5]
Options: Min 0.0V, Max: 5.0V
KEEX-2130 User’s Manual
41
Exit
Chapter 4
Power Menu
Table 48 Power Menu
BIOS SETUP UTILITY
Main
Advanced
Power Management Setting
ACPI Function
Suspend mode
Repost Video on S3 Resume
Suspend Time Out
Restore on AC Power Loss
Resume By USB Device
Resume On PME#
Resume On RTC Alarm
Boot
Chipset
[Enabled]
[S1 (POS)]
[No]
[Disabled]
[Power Off]
[Disabled]
[Disabled]
[Disabled]
Power
Security
Exit
Select the ACPI state used for
System Suspend
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
ACPI Function
Enable/ Disable ACPI support for Operating System.
ENABLE: If OS supports ACPI, DISABLE: IF OS Does not support ACPI.
Suspend mode
Options: S1 (POS), S3 (STR)
Repost Video on S3 Resume
Determines whether to invoke VGA BIOS post on S3/STR resume.
Options: No, Yes
Suspend Time Out
Options: Disabled, 1 Min, 2 Min, 4 Min, 8 Min, 10 Min, 20 Min, 30 Min, 40 Min, 50
Min, 60 Min
Restore on AC Power Loss
Options: Power OFF, Power ON, Last State
Resume By USB Device
Options: Disabled, Enabled
Resume On PME#
Options: Disabled, Enabled
Resume On RTC Alarm
Options: Disabled, Enabled
KEEX-2130 User’s Manual
42
Chapter 4
„ Security Menu
Table 49 Security Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Chipset
Power
Security
Exit
Install or Change the password.
Security Setting
Supervisor Password :Not Installed
User Password :Not Installed
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
Change Supervisor Password
Change User Password
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Change Supervisor Password
Select this item to set or change the supervisor password. The Supervisor Password
item on top of the screen displays the default Not Installed. After you have set a
password, this item displays Installed.
Change User Password
Select this item to set or change the user password. The User Password item on top
of the screen displays the default Not Installed. After you have set a password, this
item displays Installed.
KEEX-2130 User’s Manual
43
Chapter 4
„ Exit Menu
Table 50 Exit Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Chipset
Power
Security
Exit
Exit Setting
Exit System Setup after saving
Save Changes and Exit
the changes.
Discard Changes and Exit
Discard Changes
F10 key can be used
for this operation.
Load Optimal Defaults
Load Failsafe Defaults
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Save Changes and Exit
Exit system setup after saving the changes. Once you are finished making your
selections, choose this option from the Exit menu to ensure the values you selected
are saved to the CMOS RAM. The CMOS RAM is sustained by an onboard backup
battery and stays on even when the PC is turned off. When you select this option, a
confirmation window appears. Select [Yes] to save changes and exit.
Discard Changes and Exit
Exit system setup without saving any changes. Select this option only if you do not
want to save the changes that you made to the Setup program. If you made changes
to fields other than system date, system time, and password, the BIOS asks for a
confirmation before exiting.
Discard Changes
Discards changes done so far to any of the setup values. This option allows you to
discard the selections you made and restore the previously saved values. After
selecting this option, a confirmation appears. Select [Yes] to discard any changes and
load the previously saved values.
Load Optimal Defaults
Load Optimal Default values for all the setup values. This option allows you to load
optimal default values for each of the parameters on the Setup menus, which will
provide the best performance settings for your system. The F9 key can be used for
this operation.
KEEX-2130 User’s Manual
44
Chapter 4
Load Failsafe Defaults
Load Optimal Default values for all the setup values. This option allows you to load
failsafe default values for each of the parameters on the Setup menus, which will
provide the most stable performance settings. The F8 key can be used for this
operation.
KEEX-2130 User’s Manual
45
Chapter 5
Chapter 5
Driver Installation
If your KEEX-2130 does not come with an operating system pre-installed, you will
need to install an operating system and the necessary drivers to operate it. After you
have finished assembling your system and connected the appropriate power source,
power it up using the ATX Power Switch and install the desired operating system.
You can download the drivers for the KEEX-2130 from the Quanmax website at
www.quanmax.com and install as instructed there. For other operating systems,
please contact Quanmax.
NOTE
When the system reboots without connecting the CRT, there might be no
image on screen when you insert the CRT/VGA cable. Please
pressing <Ctrl>+<Alt>+<F3> simultaneously to show the image on screen.
KEEX-2130 User’s Manual
46
Appendix A
Appendix A
DIO (Digital I/O) Sample Code
//============================================
//KEEX-2130 DOS DIO sample program
//Please compile with Turbo C 3.0 to utilized the program
//============================================
Int main(){
//Output RetVal to Digital Output
//Set all output to 1
outp(0x48d, 0xF0);//DO0 is bit 4
//DO1 is bit 5
//DO2 is bit 6
//DO3 is bit 7
//Set all output to 0
outp(0x48d, 0x00);
//Reading Digital input
RetVal=inp(0x48c);//DI0 is bit 6
//DI1 is bit 7
RetVal=inp(0x4B8);//DI2 is bit 6
RetVal=inp(0x48d);//DI3 is bit 1
Return 0;
}
KEEX-2130 User’s Manual
47
Appendix A
Appendix B
WatchDog Timer Sample Code
//============================================
//KEEX-2130 DOS Watchdog sample program
//Please compile with Turbo C 3.0 to utilized the program
//============================================
int main()
{
//Initialized the WDT program
outp(0x2e,0x87);
outp(0x2e,0x01);
outp(0x2e,0x55);
outp(0x2e,0x55);
//Setting Logical Device Number to 0x07
outp(0x2e,0x07);
outp(0x2f,0x07);
outp(0x2e,0xf1);
outp(0x2f,0x44);
outp(0x2e,0xf4);
outp(0x2f,0xea);
//Set Timer Value(0x73 is LSB while 0x74 is MSB)
outp(0x2e,0x73);
outp(0x2f,0x14);//set to 20 sec (0x14)
//Set Timer Unit to Second/Minute(Bit 7 equal to 1 is second/0 is minute)
outp(0x2e,0x72);
outp(0x2f,0x80);//The unit is set as second
return 0;
}
KEEX-2130 User’s Manual
48