PHASE 7.5
NON-COIN
USER’S MANUAL
(S.A.F.E.)
American Dryer Corporation
88 Currant Road
Fall River, MA 02720-4781
Telephone: (508) 678-9000 / Fax: (508) 678-9447
E-mail: techsupport@amdry.com
www.amdry.com
071003DCAMPBELL/tcosta
ADC Part No. 113196
Retain This Manual In A Safe Place For Future Reference
Please read this manual carefully to thoroughly familiarize yourself with the Phase 7.5 non-coin computer
system features, operational instructions, and programming characteristics. This manual contains important
information on how to employ ALL the features of your new ADC dryer in the safest and most economical
way.
American Dryer Corporation products embody advanced concepts in engineering, design, and safety. If
this product is properly maintained, it will provide many years of safe, efficient, and trouble free operation.
We have tried to make this manual as complete as possible and hope you will find it useful. ADC reserves the
right to make changes from time to time, without notice or obligation, in prices, specifications, colors, and
material, and to change or discontinue models.
NOTE: If power to the dryer is off, the S.A.F.E. system is disabled.
Table of Contents
SECTION I
INTRODUCTION ....................................................................................................... 3
SECTION II
FEATURES.................................................................................................................. 4
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
O.
P.
Q.
R.
S.
T.
U.
V.
W.
X.
Dependable Microprocessor Solid State Integrated Circuitry ....................................................... 4
Sensor Activated Fire Extinguishing (S.A.F.E.) System ................................................................ 4
Program Changes Are Easily Made At The Keyboard (Touch Pad) ............................................. 4
Automatic Drying Cycle (Patent No. 4,827,627) ......................................................................... 4
Timed (Manual) Drying Cycle ..................................................................................................... 4
Preprogrammed Cycles .............................................................................................................. 4
Manually Loaded Cycles ............................................................................................................ 4
Variable (Programmable) Fabric/Temperature Selections ............................................................. 4
Cool Down/Controlled Cool Down Program ............................................................................... 4
L.E.D. Display ............................................................................................................................ 4
Wrinkle Guard Program .............................................................................................................. 4
Diagnostics ................................................................................................................................. 4
Audio Alert Signal ....................................................................................................................... 4
Temperature Conversion Status ................................................................................................... 5
Axial Mode ................................................................................................................................ 5
High-Temperature Protection ...................................................................................................... 5
Cycle Preview ............................................................................................................................ 5
Reversing Option ........................................................................................................................ 5
RPM .......................................................................................................................................... 5
Clean Lint ................................................................................................................................... 5
Language Selection ..................................................................................................................... 5
Model Selection ......................................................................................................................... 5
Default Factory Settings .............................................................................................................. 5
Keyboard (Touch Pad) Symbols ................................................................................................. 5
SECTION III
PROGRAM SELECTIONS ...................................................................................... 6
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
Preprogrammed Cycles .............................................................................................................. 6
Manually Loaded Cycles ............................................................................................................ 7
Automatic Drying Cycle (Patent No. 4,827,627) Operations ....................................................... 8
Timed (Manual) Drying Cycle Operation ..................................................................................... 8
Light Emitting Diode (L.E.D.) Dot Matrix Display ........................................................................ 8
Cycle In Progress Temperature Display ....................................................................................... 9
Temperature Conversion Status ................................................................................................... 9
Wrinkle Guard Program .............................................................................................................. 9
Audio Alert On Times 0 to 10 ................................................................................................... 10
Preprogrammed Cycle Preview ................................................................................................. 10
Reversing Option ...................................................................................................................... 10
Diagnostics ............................................................................................................................... 11
Program Locations ................................................................................................................... 11
SECTION IV
OPERATING INSTRUCTIONS ............................................................................. 14
A. Operating Sequence ................................................................................................................. 14
B. Operating Notes ....................................................................................................................... 18
C. Sensor Activated Fire Extinguishing (S.A.F.E.) System Theory Of Operation ............................. 19
SECTION V
L.E.D. DISPLAY MESSAGES ................................................................................ 21
A. L.E.D. Display Operating Status ............................................................................................... 21
SECTION VI
PROGRAMMING INSTRUCTIONS .................................................................... 22
A. Introduction to Programming ..................................................................................................... 22
B. Programming Flowcharts .......................................................................................................... 24
SECTION VII
FACTORY PRESET PARAMETERS (PROGRAMS)........................................ 65
A. Cycle “A-F” Parameters (Programs) Preset By The Factory ...................................................... 65
B. Cycle “0-40” Parameters (Programs) Preset By The Factory ..................................................... 66
SECTION VIII
PHASE 7.5 NON-COIN PROGRAMMING LIMITS .......................................... 67
A. Preprogrammed Cycles ............................................................................................................ 67
B. System Parameters (Program Locations) ................................................................................... 68
C. Fixed Parameters ...................................................................................................................... 68
SECTION IX
PHASE 7.5 AUTO CYCLE (PATENT NO. 4,827,627) CYCLE ADJUSTMENT
VALUES...................................................................................................................... 69
SECTION X
PHASE 7.5 NON-COIN SYSTEM DIAGNOSTICS ............................................ 70
A.
B.
C.
D.
Diagnostic (L.E.D. Display) Fault Messages .............................................................................. 70
S.A.F.E. System Diagnostic Conditions ..................................................................................... 71
Input/Output (I/O) Board Light Emitting Diode (L.E.D.) Indicators ............................................ 72
Keyboard (Touch Pad) Layout ................................................................................................. 73
SECTION XI
CUSTOMER CUSTOM PARAMETER SETTINGS .......................................... 74
SECTION I
INTRODUCTION
PHASE 7.5 “NON-COIN” MICROPROCESSOR DRYING SYSTEM
The American Dryer Corporation’s Phase 7.5 Non-Coin Drying System has been designed with super
performance in mind to provide for better temperature regulation, efficiency, performance, consistency, and
faster drying times.
Among its many amenities, ADC’s Phase 7.5 Non-Coin Drying System has a true Automatic Drying Cycle.
The Phase 7.5 Non-Coin Automatic Drying Cycle (Patent No. 4,827,627) principle is based on one (1) of the
most fundamental laws of thermodynamics, which governs the flow of heat in thermal systems.
Utilizing this microprocessor technology, the user simply has to place the load in the dryer and push one (1) single
button to start the drying cycle. The Phase 7.5 non-coin microprocessor controller (computer) will directly
monitor the moisture content in the load and stop the drying cycle automatically when the selected dryness level
is reached.
The ADC Phase 7.5 Non-Coin Automatic Drying Cycle (Patent No. 4,827,627) virtually eliminates ALL
guesswork. The Phase 7.5 non-coin microprocessor controller (computer) determines how much drying time is
needed and compensates for various types of fabrics and load sizes, thus, avoiding damage to fabrics by over
drying, as well as avoiding wasted time and energy for any given load. Once the Phase 7.5 non-coin microprocessor
controller (computer) determines the load is dry, the microprocessor controller (computer) will go into Cool
Down Cycle until the preprogrammed time or temperature is reached, and then shuts the dryer off automatically.
3
SECTION II
FEATURES
A. Dependable Microprocessor Solid State Integrated Circuitry – To eliminate as many moving parts as
possible.
B. Sensor Activated Fire Extinguishing (S.A.F.E.) System – A standard feature, which continually monitors
the basket (tumbler) for fires, in the event of a fire a water supply to the basket (tumbler) will suppress the
fire. The Phase 7.5 non-coin microprocessor controller (computer) will also notify the user that a fire has
taken place.
C. Program Changes Are Easily Made At The Keyboard (Touch Pad) – Actual programs are viewed at
the light emitting diode (L.E.D.) display for verification.
D. Automatic Drying Cycle (Patent No. 4,827,627) – Computerized monitoring of load dryness for precise,
fast, and efficient drying.
E. Timed (Manual) Drying Cycle – For special loads, programming allows for a specific amount of time in
minutes for both drying and Cool Down Cycles.
F. Preprogrammed Cycles – The Phase 7.5 non-coin microprocessor controller (computer) can store in its
memory six (6) preprogrammed cycles in either the Automatic Drying Mode (Patent No. 4,827,627) or
Manual Drying Mode in the “A-F” keys and an additional 41 in the numerical memory of “0-40.”
G. Manually Loaded Cycles – For occasional or onetime special loads, the user can set a specific program in
either the Automatic Drying Cycle (Patent No. 4,827,627) or Manual Timed Drying Cycle.
H. Variable (Programmable) Fabric/Temperature Selections – Accommodates the type of fabric to be
dried.
I. Cool Down/Controlled Cool Down Program – Cool down lowers the temperature of the exhaust to
make the material cool enough to handle. Controlled cool down slowly lowers the temperature over 10
minutes for materials sensitive to shrinking.
J. L.E.D. Display – Informs user of cycle status, programs and displays important diagnostic and fault codes.
K. Wrinkle Guard Program – Helps keep items wrinkle-free when they are not removed from the dryer
promptly at the end of the drying and cooling cycles.
L. Diagnostics – Major circuits, including the door switch(es), microprocessor temperature sensor and heat
output circuits, and more are individually monitored, give precise messages of your failure.
M. Audio Alert Signal – The tone will sound at the end of a complete drying cycle at a 1-second rate for the
duration programmed. It will also sound for any fault conditions at a quarter second rate for 4-beeps. Finally,
there is a 3-beep warning at the beginning of every Wrinkle Guard On Cycle. A continuous rapid pulse is
used for the entire duration of S.A.F.E. system activation.
4
N. Temperature Conversion Status – Temperature related programs can be set in either Fahrenheit (ºF) or
Celsius (ºC). ALL temperatures will automatically convert to the corresponding values (+/- 1º) when changes
are made.
O. Axial Mode – When in Axial Mode, the maximum temperature is limited to 150° F (66° C), ALL of the
temperature menus will adjust accordingly.
P. High-Temperature Protection – If the Phase 7.5 non-coin microprocessor controller (computer) senses
that the temperature in the basket (tumbler) has exceeded 170º F (77º C) for axial airflow, 220º F (104º C) for
radial airflow, it will end the drying cycle and a fault code will be displayed, indicating an overheating problem.
Q. Cycle Preview – Entire dryer parameters (programs) or the preprogrammed cycles are displayed for
verification upon a coded entry to the keyboard (touch pad).
R. Reversing Option – Helps reduce the balling up or tangling of large items. A cycle can be set to have the
reversing option where the basket (tumbler) will turn in the forward direction from 30- to 120-seconds, stop
from 5- to 10-seconds, and then proceed in the reverse direction for the same time. This process is repeated
throughout the drying and cooling cycles.
S. RPM – The Phase 7.5 non-coin microprocessor controller (computer) also displays basket (tumbler) RPM
by pressing and holding the “DOWN ARROW” key while the basket (tumbler) is on. (The basket [tumbler]
must be rotating for approximately 30-seconds before getting a true RPM reading).
T. Clean Lint – This feature monitors the value of the “Lint Cleaning Frequency” timer. The timer keeps track
of how long the dryer’s blower/fan has been on and compares it to the Lint Cleaning Frequency setting.
Once the timer equals the Lint Cleaning Frequency setting, the microprocessor will begin to prompt the user
to “CLEAN LINT.” The microprocessor will allow two (2) additional hours of run time before the control is
locked-out in “CLEAN LINT” state. The dryer will not be cleared from this state until the lint drawer has
been cleaned. When the lint drawer is opened, the display will read “Lint Access Open” and when the lint
drawer is closed, the display will read “READY.” (NOTE: The lint drawer must be opened for 15-seconds
or more for the reset to occur. The dryer circuit is now active and can be programmed.)
U. Language Selection – Phase 7.5 has the ability to display five (5) different languages, English, French,
Spanish, Italian, and German.
V. Model Selection – The Phase 7.5 can be programmed to be used on three (3) modes of heat, gas, steam,
and electric. It can also be configured for reversing and non-reversing dryers.
W. Default Factory Settings – This feature will set ALL programmed parameters to their default values.
X. Keyboard (Touch Pad) Symbols
= “STOP/CLEAR” key
= “UP ARROW” key (scroll up)
= “START/ENTER” key
= “DOWN ARROW” key (scroll down)
5
SECTION III
PROGRAM SELECTIONS
A. PREPROGRAMMED CYCLES
“A-F” CYCLES
The Phase 7.5 non-coin microprocessor controller (computer) can store in its memory six (6) preprogrammed
cycles (keys “A-F” on the keyboard [touch pad]). This allows the user to have the six (6) most commonly used
cycles, requiring only the push of a single keyboard (touch pad) entry to start the dryer.
“0-40” CYCLES
The Phase 7.5 non-coin microprocessor controller (computer) can store 41 preprogrammed cycles in its numerical
memory. (Use keys “0-9” on the keyboard [touch pad]). This allows the user to have up to 41 customized
programmed cycles that may not be as commonly used as the six (6) “A-F.” These are not one (1) touch entries
to start the dryer like the “A-F.” They are selected by entering the number, which represents the cycle desired
and pressing the “START/ENTER”
key to start the cycle.
Both types of the preprogrammed cycles can be set in either the Automatic Drying Mode (Patent 4,827,627),
where the drying cycle will end when the selected dryness level has been reached, or in the Manual Timed
Drying Mode where the dryer will operate for the specific drying time programmed. These cycles can be
programmed in any combination.
Once the heating cycle is completed, the Phase 7.5 non-coin microprocessor controller (computer) then goes
into the Cool Down Cycle where the articles are tumbled at room temperature or a controlled cool down where
the dryer goes into a slow cool down mode for 10 minutes sloping the temperature 10º F (-12º C) every minute.
When the cooling cycle is completed, the dryer will go into the Wrinkle Guard Cycle. For the first 15 minutes of
wrinkle guard, the control will remain idle with the display reading “CYCLE DONE.” After the 15 minutes have
elapsed, the control will beep three (3) times and will activate the basket (tumbler) for 15-seconds without heat.
At this point, the display will read “WRINKLE GUARD.” Once the 15-seconds are over, the control will
display “CYCLE DONE” and will remain idle for 5 minutes, at which point the control will reactivate the basket
(tumbler) for 15-seconds while displaying “Wrinkle Guard.” The control will continue with the process of
15-seconds “ON” 5 minutes “OFF” until either the doors are opened, the “STOP/CLEAR”
key is pressed,
or 99 minutes has elapsed, whichever comes first. Once the Wrinkle Guard routine has ended, the display will
read “CYCLE DONE.” At this point, the dryer is locked out from drying again until the doors are opened. This
will insure that if a cycle has been completed, the operator will attend to it before starting another heat cycle.
NOTE: To enter program mode, press “STOP/CLEAR”
key and the
“UP ARROW” key.
PREPROGRAMMED CYCLE MENU SELECTIONS (CYCLES “A-F” OR “0-40”):
1. Automatic Drying Cycle (Patent No. 4,827,627)
a. The Phase 7.5 non-coin microprocessor controller (computer) can be programmed to reverse or not
reverse. This is done in “DRYER SETUP” parameter.
6
b. Drying Temperature – Programmable from 160º F to 200º F (71º C to 93º C) in one-degree increments
for radial dryers and fixed at 150º F (66º C) for axial dryers.
c. Dryness Level – Programmable for finishing, dry, and extra dry.
d. Cool Down Time – Programmable from 0 to 99 minutes in 1 minute increments.
e. Cool Down Temperature – Programmable from 70º F to 100º F (21º C to 38º C) in one-degree increments.
f. Cycle Adjustment – Programmable from 0 to 99.
2. Timed (Manual) Cycle
a. The Phase 7.5 non-coin microprocessor controller (computer) can be programmed to reverse or not
reverse. This is done in “DRYER SETUP” parameter.
b. Drying Time – Programmable from 0 to 99 minutes in 1 minute increments.
c. Drying Temperature – Programmable from 100º F to 200º F (38º C to 93º C) in one-degree increments
and preset at 150º F (66º C) for axial.
d. Cool Down Time – Programmable from 0 to 99 minutes in 1 minute increments.
e. Cool Down Temperature – Programmable from 70º F to 100º F (21º C to 38º C) in one-degree increments.
f. The Spin Time can be programmed from 30-seconds to 120-seconds in 1-second increments.
g. The Stop Time can be programmed from 5-seconds to 10-seconds in 1-second increments.
ALL six (6) “A-F” preprogrammed cycles along with cycles “0-40” have been programmed by the
factory as outlined in Section VII. However, even though cycles “A-F” are the most common cycles
used, they should be reviewed to ensure they meet the location application or needs. Should changes
be found necessary, refer to the Programming Section of this manual.
B. MANUALLY LOADED CYCLES
For occasional or onetime special loads, the operator must enter the specific program features needed. This
cycle is not stored within the Phase 7.5 non-coin microprocessor controller (computer) and must be entered
each and every time.
The Manually Loaded Cycle can be set in either the Automatic Drying Mode (Patent No. 4,827,627) or the
Timed (Manual) Drying Mode. These are selected by pressing the “AUTO” or “MAN” keys on the keyboard
(touch pad).
7
C. AUTOMATIC DRYING CYCLE (PATENT NO. 4,827,627) OPERATIONS
In this mode, the Phase 7.5 non-coin microprocessor controller (computer) determines how much drying time is
needed and compensates for various types of fabrics and load sizes, ALL automatically. The Phase 7.5
non-coin microprocessor controller (computer) accomplishes this by calculating the dryness level (percentage of
extraction) using the temperature selected, as well as, the dryness level preset by the factory.
The Phase 7.5 non-coin microprocessor controller (computer) monitors the first three (3) heat peaks (slopes), at
which time it calculates the dryness level (heat loss) along with the percentage of extraction selected. When the
Phase 7.5 non-coin microprocessor controller (computer) determines that ALL the factors are met, the drying
cycle will end, and the dryer will go into the Cool Down Cycle.
D. TIMED (MANUAL) DRYING CYCLE OPERATION
This drying cycle is intended for special loads where a specific amount of drying time and cooling time is needed,
especially for fine, delicate items which require very low temperatures and long drying and/or Cool Down Time
periods.
ALL the parameters set in “COOL DOWN SETUP” pertain to the Manually Loaded Manual and Auto Cycles.
The “A-F” and “0-40” cycles that have been selected to be manual, have separate settings for ALL the parameters
contained in the “COOL DOWN SETUP” menu.
The program limitation is the same as in Section III, A2.
NOTE: The Cool Down Cycle will run either until the Cool Down Temperature is reached or until the
Cool Down Time has expired, whichever comes first.
NOTE: If there has been no Drying Time selected, then the Cool Down Cycle will ignore the Cool
Down Temperature and do the Cool Down Time only.
E. LIGHT EMITTING DIODE (L.E.D.) DOT MATRIX DISPLAY
The L.E.D. display informs the user of cycle status, program verification, and displays important diagnostic and
fault information. A complete listing of the various display messages and their meanings are shown in Section
V of this manual.
CYCLE IN PROGRESS DISPLAY STATUS
During the Drying Cycle, the display will indicate the type of cycle in progress by presenting either one (1) of the
following:
1. “AUTO DRYING CYCLE” – Manually Loaded Auto Cycle.
2. “AUTO DRYING CYCLE #” – The “#” is replaced with “A-F” or “0-40.”
3. “MANUAL DRYING CYCLE” – Manually Loaded Manual Cycle.
8
4. “MANUAL DRYING CYCLE #” – The “#” is replaced with “A-F” or “0-40.”
F. CYCLE IN PROGRESS TEMPERATURE DISPLAY
While the dryer cycle is in progress, the temperature in the basket (tumbler) can be displayed by pressing and
holding the “UP ARROW” key. The temperature will be displayed in either Fahrenheit (ºF) or Celsius (ºC),
depending on what the system temperature has been set for in “DRYER SETUP.”
G. TEMPERATURE CONVERSION STATUS
Temperature related programs are programmable to be operated in either Fahrenheit (ºF) or Celsius (ºC). The
temperature selection is made in “SYSTEM TEMP.” Programs affected are:
1. Temperature Display Mode
2. Drying Temperatures
3. Cool Down Temperatures
IMPORTANT: When changing the temperature conversion status from Fahrenheit to Celsius or vice
versa, ALL the Temperature Selections and Cool Down Temperatures will be
changed accordingly. The Phase 7.5 non-coin microprocessor controller (computer)
automatically calculates and converts the temperatures in these programs to the
previously set value. For example, when changing from ºF to ºC, if the
preprogrammed Cycle “A” drying temperature was set for 160º F, the Phase 7.5
non-coin microprocessor controller (computer) will change to 71º C (+/- one-degree
Celsius).
H. WRINKLE GUARD PROGRAM
This program keeps items wrinkle-free when they are not removed from the dryer promptly at the end of the
drying cycle and/or cooling cycle.
When the drying and cooling cycles are completed, the dryer will shut off, the tone will sound, and the light
emitting diode (L.E.D.) display will read “CYCLE DONE.” If the door is not opened or the cycled stopped, the
Phase 7.5 non-coin microprocessor controller (computer) will wait an initial 15 minutes delay time. Once the
initial 15 minute delay time has expired, the fan will start and the basket (tumbler) will rotate (without heat) for
an ON time of 15-seconds. When the fan and basket (tumbler) start, the display will read “WRINKLE GUARD.”
Immediately following the 15-second ON time, the control will go into a 5 minute OFF time at which point it will
display “CYCLE DONE.” The Phase 7.5 non-coin microprocessor controller (computer) will repeat this process
key is
of 15-seconds “ON” and 5 minutes “OFF” until either the doors are opened, the “STOP/CLEAR”
pressed, or 99 minutes has elapsed, whichever comes first. Prior to each ON time, there is a 3-beep warning
that the fan and basket (tumbler) rotation are about to start. The beeps at the end of the Wrinkle Guard Cycle
can be programmed to be ON/OFF. This is done in “WRINKLE GUARD SETUP.”
9
WRINKLE GUARD PROGRAM SELECTIONS:
1. Wrinkle Guard Audio Alert On/Off
The operator can select to turn on or off the beeps at the end of each Wrinkle Guard Cycle. The amount
of beeps is programmed in “AUDIO ALERT ON TIMES.”
I. AUDIO ALERT ON TIMES 0 TO 10
The tone will sound at the end of the Cool Down Cycle to indicate that the cycle is complete. Programming
allows for the elimination of the tone during the Wrinkle Guard Cycle. This is done in “WRINKLE GUARD
SETUP.” Programming also allows the beeps to be set from 0 to 10 times in increments of one (1). This is done
in “DRYER SETUP.”
J. PREPROGRAMMED CYCLE PREVIEW
The parameters of the preprogrammed cycles can be displayed for verification. To view an “A-F” preset
program (parameter), simply press the “START/ENTER”
key and the desired preset program “A-F.” The
light emitting diode (L.E.D.) display will read the program parameter settings, then return to the “READY”
display mode. To view a “0-40” preset program parameter, simply press the “START/ENTER”
key and the
desired preset program number “0-40” followed by “START/ENTER”
key again. The L.E.D. display will
read the program parameter settings, then return to the “READY” display mode.
K. REVERSING OPTION
This feature helps reduce balling up or tangling of large items.
REVERSING OPTION SELECTIONS:
1. Reverse On or Reverse Off
2. This Is Set For Each Cycle
3. Basket (Tumbler) Spin Time and Stop Time
a. Fixed in the Automatic “AUTO” Mode and cannot be changed.
1) Spin Time – 2 minutes forward and 2 minutes reverse.
2) Stop Time – 5-seconds.
b. Programmable in the Manual Mode.
1) Spin Time – Programmable from 30-seconds to 120-seconds in 1-second increments.
2) Stop Time – Programmable from 5-seconds to 10-seconds in 1-second increments.
10
L. DIAGNOSTICS
The Phase 7.5 non-coin microprocessor controller (computer) monitors “Drying function,” which is the following:
1. Drying Functions: These include temperatures, burners, sail switches, blower, basket (tumbler), and lint
drawer.
M. PROGRAM LOCATIONS
This is where system parameters are programmed. These system parameters (programs) are stored in memory.
and the “UP ARROW” together. To
Access to this location is acquired by pressing the “STOP/CLEAR”
exit the Programming Location, simply press the “STOP/CLEAR”
key. If you are several menu layers
deep, continue to press the “STOP/CLEAR”
key to back up the menu until you are ALL the way out of the
programming mode.
0. SELECT LANGUAGE – This menu allows the selection of five (5) different languages to operate the
dryer. The language that is selected will be used for every displayed message as well as faults and menus.
ENGLISH
FRENCH
SPANISH
ITALIAN
GERMAN
1. SELECT SYSTEM PARAMETERS – This menu level has four (4) sections. ALL programmable parameters
other than preprogrammed cycles are done here.
0. DRYER SETUP – ALL parameters that pertain to drying are in this menu level.
0. SELECT MODEL – This allows the selection of the heat source applied to the dryer as well as if
the dryer is reversing or non-reversing.
GAS (reversing)
STEAM (reversing)
ELECTRIC (reversing)
GAS (non-reversing)
STEAM (non-reversing)
ELECTRIC (non-reversing)
1. SYSTEM TEMP – This selection controls whether the temperature related programs will be operated
in Fahrenheit (ºF) or Celsius (ºC). The programs affected are as follows:
1) Temperature Display Mode
2) Drying Temperatures
3) Cool Down Temperatures
11
IMPORTANT: The Phase 7.5 non-coin microprocessor controller (computer) automatically calculates
and converts the temperatures in these programs to the previously set value. For
example, when changing from ºF to ºC, if the preprogrammed Cycle “A” drying
temperature was set for 160º F, the Phase 7.5 non-coin microprocessor controller
(computer) will change to 71º C (+/- one-degree Celsius).
2. ENTER LINT CLEANING FREQUENCY 1 TO 10 HOURS – This selection sets how long the
lint cleaning timer will run before prompting the user to “CLEAN LINT.” Once the user is prompted
to “CLEAN LINT,” the control will allow an additional 2 hours of run time before the dryer is
placed into a locked out state, waiting for the lint drawer to be cleaned.
NOTE: A minimum of 15-seconds is required to have the lint drawer opened in order to return to the
“READY” state once it is closed.
3. ENTER AUDIO ALERT ON TIMES 0 TO 10 – This selection allows the operator to adjust the
amount of signal tones. This parameter (program) affects the tone at the end of the Cool Down
Cycle, as well as, at the end of the Wrinkle Guard On Time.
4. ROTATION SENSOR – This selection is used to turn the rotation sensor on or off.
5. AXIAL THERMISTOR INPUT – This selection is used to turn the axial thermistor on or off.
6. ENTER AXIAL TRIP TEMP 100º TO 400º F (38º TO 204º C) – This selection allows the operator
to select the trip temperature of the axial thermistor.
1. REVERSING SETUP – The parameters that pertain to the reversing mode are in this menu level.
0. ENTER SPIN TIME 30- TO 120-SECONDS – This parameter (program) is fixed at 2 minutes in the
forward direction and 2 minutes in the reverse direction for the Automatic Mode. In the Manual Mode,
it is programmable. This Spin Time is programmed here for the Manually Loaded Manual Cycle only.
1. ENTER STOP TIME 5- TO 10-SECONDS – This parameter (program) is fixed at 5-seconds in the
Automatic Mode and programmable in the Manual Mode. This Stop Time is programmed here for the
Manually Loaded Manual Cycle only.
2. WRINKLE GUARD SETUP – The parameters that pertain to the Wrinkle Guard is in this menu level.
0. WRINKLE GUARD AUDIO ALERT – This parameter (program) allows the operator to turn the
Audio Alert tone on or off at the end of each Wrinkle Guard Cycle. The amount is the same that is
selected in “DRYER SETUP” for AUDIO ALERT ON TIMES 0 TO 10.
AUDIO ALERT ON
AUDIO ALERT OFF
2. PROGRAM “A-F” CYCLE – This menu allows the programming of cycle “A-F.” The parameters selected
in this menu for each letter will be stored in memory for that key. This will allow the operator to utilize one
(1) touch drying through keys “A-F.”
3. PROGRAM “0-40” CYCLE – This menu allows the programming of cycle “0-40.” The parameters
selected in this menu for each number will be stored in memory for that number key(s). This will allow the
operator to utilize preprogrammed drying cycles stored in memory under a numerical location.
12
NOTE: BOTH THE “A-F” AND “0-40” ALLOWS FOR A TOTAL OF 47 PREPROGRAMMED
LOCATIONS FOR CUSTOM DRYING.
4. DEFAULT SETTINGS – This menu allows the operator to set ALL the programmable parameters to the
default settings. This option has a password selection of 1 2 3. It will then ask to confirm settings. It will
default to “NO.” Use the arrow keys to select “YES.”
CAUTION: Once the settings have been set to their default settings, there is no way to
retrieve the old settings. Use caution when using this feature.
13
SECTION IV
OPERATING INSTRUCTIONS
The Phase 7.5 non-coin microprocessor controller (computer) allows the operator to choose from six (6)
preprogrammed cycles (keys “A-F”). These have been preprogrammed by the factory with the parameters
(programs) shown in Section VII. There are an additional (“0-40”) preprogrammable cycles that are
preprogrammed by the factory with the parameters (programs) shown in Section VII. For occasional or
onetime special loads, the Manually Loaded Cycles can be used where the operator must set the specific
program(s) needed.
NOTE: Refer to Section III of this manual for a complete explanation of the various cycles/selections
available.
After the load is put into the basket (tumbler) and the dryer is ready to dry, determine which cycle will best suit
the application (type of load). We recommend using the Automatic Drying Cycle (Patent No. 4,827,627) for
most loads. This cycle provides for the best drying in the shortest time, ALL automatically.
A. OPERATING SEQUENCE
1. Preprogrammed Cycles
a. Automatic Drying Cycle (Patent No. 4,827,627)
1) Light emitting diode (L.E.D.) display reads “READY” (no cycle in progress).
2) Press the letter on the keyboard (touch pad) corresponding to the cycle desired (i.e., key “A”).
NOTE: “0-40” will require the “START/ENTER”
key to be pressed after the number is selected in
order to accept the selection and start drying.
3) The dryer will then start. (I.E., blower, basket [tumbler], and heat).
4) L.E.D. display reads AUTO DRYING CYCLE “A,” ELAPSED TIME __ MIN 00:00. During the
drying cycle, the Phase 7.5 non-coin microprocessor controller (computer) will monitor the amount
of moisture in the load. Once the temperature is above 160º F (71º C), the Cycle Status portion of
the L.E.D. will change from ELAPSED TIME __ MIN to __ % DRY. The display will count
upward until the percentage of extraction programmed is reached.
NOTE: Press and hold the “UP ARROW” to view the basket (tumbler) temperature at any time.
NOTE: The dryer can be stopped at any time by pressing the “STOP/CLEAR”
key, at this time
the dryer will go into a cycle pause. If the “STOP/CLEAR”
key is pressed again at this
point, the cycle that was in progress will be cancelled and returned to the “READY” state.
14
5) Once the preprogrammed percentage of extraction (dryness level) is reached, the drying cycle will
end and the Cool Down Cycle will begin.
6) Once the Cool Down Cycle begins at the end of the heat cycle, the light emitting diode (L.E.D.)
display will read COOL DOWN TEMP ___/___ MINUTES REMAINING. At the end of the
heat cycle, the dryer will shut off the heat and continue the fan and basket (tumbler) until the Cool
Down Time or temperature is reached.
7) Once the Cool Down Cycle is completed, the Phase 7.5 non-coin microprocessor controller (computer)
will proceed into the Wrinkle Guard Cycle. The Audio Alert tone will sound for the amount set in
Audio Alert On Time. The L.E.D. display will read “CYCLE DONE.” The dryer will wait an
initial 15 minutes delay before going into a 15-second ON, 5 minute OFF cycle. These times are
fixed and are not programmable. During the ON time, the blower (fan) and the basket (tumbler)
will start to rotate without heat for 15-seconds, during this time the display will read “WRINKLE
GUARD.” After the 15-seconds are completed, the display will read “CYCLE DONE” and the
dryer will go into a 5 minute OFF cycle. The Phase 7.5 non-coin microprocessor controller (computer)
will repeat this process of 15-seconds “ON” and 5 minutes “OFF” until either the doors are opened,
key is pressed, or 99 minutes has elapsed, whichever comes first. Once
the “STOP/CLEAR”
the 99 minutes has elapsed, the L.E.D. display will then read “CYCLE DONE” and will lockout the
dryer functions until the doors are opened. It will then return to “READY.”
b. Timed (Manual) Drying Cycle
1) L.E.D. display reads “READY” (no cycle in progress).
2) Press the letter on the keyboard (touch pad) corresponding to the cycle desired (i.e., key “D”).
NOTE: “0-40” WILL REQUIRE THE “START/ENTER”
KEY TO BE PRESSED AFTER THE
NUMBER IS SELECTED IN ORDER TO ACCEPT THE SELECTION AND START
DRYING.
3) The dryer will then start. (I.E., blower, basket [tumbler], and heat).
4) The L.E.D. display will read MANUAL DRYING CYCLE D, 00:00 MIN REMAIN.
NOTE: Press and hold the “UP ARROW” to view the basket (tumbler) temperature at any time.
NOTE: The dryer can be stopped at any time by pressing the “STOP/CLEAR”
key, at this time
the dryer will go into a cycle pause. If the “STOP/CLEAR”
key is pressed again at this
point, the cycle that was in progress will be cancelled and returned to the “READY” state.
NOTE: Press and hold the “DOWN ARROW” to view the basket (tumbler) RPM.
5) When the programmed drying time has expired, the Phase 7.5 non-coin microprocessor controller
(computer) will proceed into the Cool Down Cycle.
6) Once the Cool Down Cycle begins at the end of the heat cycle, the L.E.D. display will read COOL
DOWN TEMP ___/___ MINUTES REMAINING. At the end of the heat cycle, the dryer will
shut off the heat and continue the fan and basket (tumbler) until the Cool Down Time or temperature
is reached.
15
7) Once the Cool Down Cycle is completed, the Phase 7.5 non-coin microprocessor controller (computer)
will proceed into the Wrinkle Guard Cycle. The Audio Alert tone will sound for the amount set in
Audio Alert On Time. The light emitting diode (L.E.D.) display will read “CYCLE DONE.” The
dryer will wait an initial 15 minutes delay before going into a 15-second ON, 5 minute OFF cycle.
These times are fixed and are not programmable. During the ON time, the blower (fan) and the
basket (tumbler) will start to rotate without heat for 15-seconds, during this time the display will
read “WRINKLE GUARD.” After the 15-seconds are completed, the display will read “CYCLE
DONE” and the dryer will go into a 5 minute OFF cycle. The Phase 7.5 non-coin microprocessor
controller (computer) will repeat this process of 15-seconds “ON” and 5 minutes “OFF” until either
the doors are opened, the “STOP/CLEAR”
key is pressed, or 99 minutes has elapsed, whichever
comes first. Once the 99 minutes has elapsed, the L.E.D. display will then read “CYCLE DONE”
and will lockout the dryer functions until the doors are opened. It will then return to “READY.”
2. Manually Loaded Cycles
a. Automatic Drying Cycle (Patent No. 4,827,627)
1) L.E.D. display reads “READY” (no cycle in progress).
2) Press AUTO key.
3) L.E.D. display will now read ENTER DRY TEMP 160 TO 200. (Defaults to 160° F [71° C]).
Enter the temperature desired (from 160º F to 200º F [71º C to 93º C] in one-degree increments).
I.E., for 180º F (82º C), press key “1,” key “8,” key “0,” and then press the “START/ENTER”
key to accept the value.
4) L.E.D. display will now read ENTER DRY LEVEL finishing, dry, and extra dry. Enter the amount
of extraction (dryness level desired). Finishing has the most moisture content to extra dry, which
has little or no moisture content.
5) L.E.D. display will now read “REVERSE MODE” (defaults to ON). The ON/OFF selection can
be toggled with the “UP ARROW” and “DOWN ARROW.” Once selected, press the
“START/ENTER”
key to accept selection.
NOTE: In addition to entering a value by pressing the number keys, the “UP ARROW” and “DOWN
ARROW” can be used to scroll to the number desired or toggle between selections.
6) The dryer will now display “PRESS START.” Press the “START/ENTER”
key to start the
dryer. The L.E.D. display will read AUTO DRYING CYCLE, ELAPSED TIME __ MIN. During
the Drying Cycle, the Phase 7.5 non-coin microprocessor controller (computer) is monitoring the
moisture in the load. Once the temperature is above 160º F (71º C), the Cycle Status portion of the
L.E.D. will change from ELAPSED TIME __ MIN to DRYNESS LEVEL__.
NOTE: Press and hold the “UP ARROW” to view the basket (tumbler) temperature at any time.
NOTE: The dryer can be stopped at any time by pressing the “STOP/CLEAR”
key, at this time
the dryer will go into a cycle pause. If the “STOP/CLEAR”
key is pressed again at this
point, the cycle that was in progress will be cancelled and returned to the “READY” state.
16
NOTE: Press and hold the “DOWN ARROW” to view the basket (tumbler) RPM.
7) Once the preprogrammed percentage of extraction (dryness level) is reached, the drying cycle will
end, and the Cool Down Cycle will begin.
8) Once the Cool Down Cycle begins at the end of the heat cycle, the light emitting diode (L.E.D.)
display will read COOL DOWN TEMP ___/___MINUTES REMAINING. At the end of the heat
cycle, the dryer will shut off the heat and continue the fan and basket (tumbler) until the Cool Down
Time or temperature is reached.
9) Once the Cool Down Cycle is completed, the Phase 7.5 non-coin microprocessor controller (computer)
will proceed into the Wrinkle Guard Cycle. The Audio Alert tone will sound for the amount set in
Audio Alert On Time. The L.E.D. display will read “CYCLE DONE.” The dryer will wait an
initial 15 minutes delay before going into a 15-second ON, 5 minute OFF cycle. These times are
fixed and are not programmable. During the ON time, the blower (fan) and the basket (tumbler)
will start to rotate without heat for 15-seconds, during this time the display will read “WRINKLE
GUARD.” After the 15-seconds are completed, the display will read “CYCLE DONE” and the
dryer will go into a 5 minute OFF cycle. The Phase 7.5 non-coin microprocessor controller (computer)
will repeat this process of 15-seconds “ON” and 5 minutes “OFF” until either the doors are opened,
the “STOP/CLEAR”
key is pressed, or 99 minutes has elapsed, whichever comes first. Once
the 99 minutes has elapsed, the L.E.D. display will then read “CYCLE DONE” and will lockout the
dryer functions until the doors are opened. It will then return to “READY.”
NOTE: Mechanical functions of the dryer are not allowed during the ON time. The blower (fan)
must be OFF to perform mechanical functions. However, the “STOP/CLEAR”
key may
be pressed at any time to end the Wrinkle Guard Cycle. Mechanical functions of the dryer are
allowed during the OFF time.
b. Timed (Manual) Drying Cycle
1) L.E.D. display reads “READY” (no cycle in progress).
2) Press MAN key.
3) L.E.D. display will now read “ENTER DRY TIME 0 TO 99 MINUTES” (defaults to 0). I.E., for
key to accept the
40 minutes, press key “4,” key “0,” and then press the “START/ENTER”
value.
4) L.E.D. display will now read “ENTER DRY TEMP __ TO __” (defaults to 100° F [38° C]). Enter
the temperature desired (from 100º F to 200º F [38º C to 93º C] in one-degree increments). I.E., for
142º F (61º C), press key “1,” key “4,” key “2,” and then press the “START/ENTER”
key to
accept the value.
5) L.E.D. display will now read “ENTER COOL DOWN TIME 0 TO 99 MINUTES.” I.E., for 10
minutes, press key “1,” key “0,” and then press the “START/ENTER”
key to accept the value.
6) L.E.D. display will now read “REVERSE MODE” (defaults to ON). The ON/OFF selection can
be toggled with the “UP ARROW” and “DOWN ARROW.” Once selected, press the
“START/ENTER”
key to accept selection.
17
7) The dryer will now display “PRESS START.” Press the “START/ENTER”
key to start the
dryer. The light emitting diode (L.E.D.) display will read MANUAL DRYING CYCLE,
__MINUTES REMAIN.
NOTE: The dryer can be stopped at any time by pressing the “STOP/CLEAR”
key, at this time
the dryer will go into a cycle pause. If the “STOP/CLEAR”
key is pressed again at this
point, the cycle that was in progress will be cancelled and returned to the “READY” state.
8) Once the programmed drying time has expired, the Phase 7.5 non-coin microprocessor controller
(computer) will proceed into the Cool Down Cycle (Mode).
9) Once the Cool Down Cycle begins at the end of the heat cycle, the L.E.D. display will read COOL
DOWN TEMP ___/___ MINUTES REMAINING. At the end of the heat cycle, the dryer will
shut off the heat and continue the fan and basket (tumbler) until the Cool Down Time or temperature
is reached.
10) Once the Cool Down Cycle is completed, the Phase 7.5 non-coin microprocessor controller (computer)
will proceed into the Wrinkle Guard Cycle. The Audio Alert tone will sound for the amount set in
Audio Alert On Time. The L.E.D. display will read “CYCLE DONE.” The dryer will wait an
initial 15 minutes delay before going into a 15-second ON, 5 minute OFF cycle. These times are
fixed and are not programmable. During the ON time, the blower (fan) and the basket (tumbler)
will start to rotate without heat for 15-seconds, during this time the display will read “WRINKLE
GUARD.” After the 15-seconds are completed, the display will read “CYCLE DONE” and the
dryer will go into a 5 minute OFF cycle. The Phase 7.5 non-coin microprocessor controller (computer)
will repeat this process of 15-seconds “ON” and 5 minutes “OFF” until either the doors are opened,
the “STOP/CLEAR”
key is pressed, or 99 minutes has elapsed, whichever comes first. Once
the 99 minutes has elapsed, the L.E.D. display will then read “CYCLE DONE” and will lockout the
dryer functions until the doors are opened. It will then return to “READY.”
B. OPERATING NOTES
1. The RPM of the basket (tumbler) can be displayed by pressing and holding the “DOWN ARROW” key
while a cycle is in progress. If cycle has not been started, the display will read CPU Board Voltage Value.
(23-26 Volts is normal).
2. The dryer can be stopped at any time by pressing the “STOP/CLEAR”
key, at this time the dryer will
go into a cycle pause. If the “STOP/CLEAR”
key is pressed again at this point, the cycle that was in
progress will be cancelled and returned to the “READY” state.
3. When programming a Manually Loaded Cycle, if an error is made making an entry, press the
“STOP/CLEAR”
key ONCE, and the entry will be cancelled. Reenter the selection. If the selection
is entered and an error is made, the “STOP/CLEAR”
key will cancel the program and return to the
“READY” state.
4. Use the “UP ARROW” and “DOWN ARROW” to scroll through menus or increase/decrease number
values or toggle between choices.
18
5. In the programming mode, the number of keys can be used to jump to menu levels without scrolling through
them ALL. I.E., from 0 select Model in “DRYER SETUP”; you can jump to menu level five (5). Enter lint
count under “DRYER SETUP” by pressing the two (2) keys followed by the “START/ENTER”
key
to accept value. Light emitting diode (L.E.D.) display will read 2: ENTER LINT CLEANING FREQUENCY
1 TO 10 HOURS.
6. The basket (tumbler) temperature can be displayed by pressing and holding the “UP ARROW” key.
7. The programmed cycle parameter can be viewed by pressing the “START/ENTER”
key followed by
the “A-F” key. To view “0-40” cycles, press “START/ENTER”
key followed by the number desired
to view followed by “START/ENTER”
key. The viewing can be stopped by pressing the
“STOP/CLEAR”
key at any time.
C. SENSOR ACTIVATED FIRE EXTINGUISHING (S.A.F.E.) SYSTEM
THEORY OF OPERATION
While the dryer is in an idle state or 20-seconds after the heat turns off, the Phase 7.5 control monitors the
thermistor probe located in the top of the basket (tumbler) chamber and records the minimum temperature. If
the minimum recorded thermistor probe temperature is greater than 120° F (49° C) and the control detects a 50°
rise in temperature, this will be the trip point and the S.A.F.E. system routine will activate.
While a drying cycle is in process and the heat has turned on at least once, the Phase 7.5 control monitors the
exhaust temperature transducer. If the drying cycle temperature set point is set greater than 160° F (71° C) and
the control detects an exhaust temperature rise 25° F greater than set point, this will be the trip point and the
S.A.F.E. system routine will activate. If set point is below 160° F (71° C), the trip point will be 185° F (85° C).
Once the S.A.F.E. system routine is activated, the control will display “S.A.F.E. SYSTEM ACTIVATED” and
water will be injected into the basket (tumbler) chamber. Any time water is being injected into the basket
(tumbler); the basket (tumbler) drive will turn the load for 1-second every 15-seconds. This process will continue
for a minimum of 2 minutes. After the 2 minutes has elapsed, the control will check if the temperature remained
above trip point, if so water will remain on. The control will continue to check if the temperature is above trip
point every 30-seconds. If the water has been on for a constant 10 minutes, the water will be turned off
regardless of the temperature and the control will display “S.A.F.E. System was Activated.” If the temperature
has dropped below trip point, the control will turn off the water prior to 10 minutes.
SYSTEM RESET
After the microprocessor determines that the situation is under control and shuts the water being injected into the
basket (tumbler) off, the microprocessor display will read “S.A.F.E. SYSTEM WAS ACTIVATED,” and the
horn/tone will sound until reset manually.
To reset the microprocessor once the control displays “S.A.F.E. SYSTEM WAS ACTIVATED,” press the red
“STOP/CLEAR”
key on the keyboard (touch pad).
NON-COIN S.A.F.E. SYSTEM VALVE CHECK
The operation of the water solenoid valve can be tested to insure that the water supply system and valve are
functional. Before attempting a system check, be sure that ALL water supply shutoff valves to the dryer are in
the OPEN position, and the dryer must be in the “READY” mode where no cycle is loaded or in progress.
19
The procedure is as follows:
1. Press and hold the red “STOP/CLEAR”
key (while in “READY” mode and no cycle is in progress).
2. Press and hold the “A” key.
3. Water valve will open and water will be dispensed into basket (tumbler) area as long as both keys are held.
The Phase 7.5 non-coin microprocessor controller (computer) will prompt the user to perform a Sensor Activated
Fire Extinguishing (S.A.F.E.) system valve check at every 4000 hours to ensure proper functionality. At the
4000 hour mark, the control will wait for end of the cycle and then will prompt the user to “PLEASE EMPTY
TUMBLER, THEN PRESS THE ‘STOP/CLEAR’ AND ‘A’ KEYS TO TEST THE WATER VALVE.” When
and “A” keys are pressed, the control will activate the S.A.F.E. system water valve
the “STOP/CLEAR”
for 2-seconds, at which point the control will prompt the user with the following message “IF WATER DID NOT
TURN ON, CALL FOR SERVICE. THANK YOU.”
NOTE: The control will not let the user continue until the valve test has been completed.
S.A.F.E. SYSTEM DIAGNOSTICS MESSAGES
In the event that the Phase 7.5 non-coin microprocessor controller (computer) detects a fault in the S.A.F.E.
system, the control will display the message “S.A.F.E. SYSTEM DISABLED…READY.” To find out the
and green “START”
reason for the S.A.F.E. system disabling, press and hold the red “STOP/CLEAR”
keys. This will cause the control to display one (1) of the following diagnostic messages:
OPEN THERMISTOR PROBE – This message indicates that the S.A.F.E. system thermistor probe is either
not connected or is damaged. If this condition is detected, the Phase 7.5 non-coin control will immediately enter
S.A.F.E. SYSTEM DISABLED mode.
SHORTED THERMISTOR PROBE – This message indicates that the S.A.F.E. system thermistor probe is
damaged or the wiring is shorted. If this condition is detected, the Phase 7.5 non-coin control will immediately
enter S.A.F.E. SYSTEM DISABLED mode.
DISCONNECTED WATER VALVE – This indicates that the water valve is open or that it is not connected
to the control. If this condition is detected, the Phase 7.5 non-coin control will continue to monitor the condition
for a period of 5 minutes before entering S.A.F.E. SYSTEM DISABLED mode. Once the condition is corrected,
the control will continue to monitor the condition for 1 minute before exiting S.A.F.E. SYSTEM DISABLED
mode.
SHORTED WATER VALVE – This indicates the water valve is shorted or the wiring to the valve is shorted.
If this condition is detected, the Phase 7.5 non-coin control will continue to monitor the condition for a period of
5 minutes before entering S.A.F.E. SYSTEM DISABLED mode. Once the condition is corrected, the control
will continue to monitor the condition for 1 minute before exiting S.A.F.E. SYSTEM DISABLED mode.
WATER NOT CONNECTED – This indicates that there is no water pressure at the water valve. This will
occur if water is not connected to the dryer or if there is low water pressure in the water line coming to the dryer.
This could also be a defective pressure switch or wiring to the pressure switch. If this condition is detected, the
Phase 7.5 non-coin control will continue to monitor the condition for a period of 5 minutes before entering
S.A.F.E. SYSTEM DISABLED mode. Once the condition is corrected, the control will continue to monitor the
condition for 1 minute before exiting S.A.F.E. SYSTEM DISABLED mode.
When the S.A.F.E. system is disabled, the user can still start a cycle, however when a cycle is started, the
control will display the following message: “S.A.F.E. SYSTEM IS DISABLED. PRESS ‘START’ TO
CONTINUE.” This message will be displayed every time a cycle is started until the disabling condition has been
corrected.
20
SECTION V
L.E.D. DISPLAY MESSAGES
The light emitting diode (L.E.D.) display informs the operator of cycle status, program verification, and displays
important diagnostic messages and fault information.
A. L.E.D. DISPLAY OPERATING STATUS
1. Cycles in Progress
a. While the dryer is operating, the L.E.D. display will read which cycle is in progress. I.E., in a Manual
Drying Cycle (Mode), the L.E.D. display will read “MANUAL DRYING CYCLE.” In the Cool Down
Cycle (Mode) the L.E.D. display will read “COOL DOWN TEMP __ , __ MINUTES REMAIN.”
2. Cycle Status
a. While a cycle is in progress, the L.E.D. display will show the progress of the cycle that is being
processed.
1) Automatic Drying Cycle
a) While a cycle is in progress, the cycle status will display ELAPSED TIME __ MIN. During the
Drying Cycle, the Phase 7.5 non-coin microprocessor controller (computer) is monitoring the
moisture in the load. Once the temperature has reached set point temperature and cycled
ON/OFF three (3) times, the cycle status portion of the L.E.D. will change from ELAPSED
TIME __ MIN to __% DRY. The display will count upward until the percentage of extraction
programmed is reached.
2) Timed (Manual) Drying Cycle
a) While a cycle is in progress the cycle status will display __ MINUTES REMAIN.
3. Alternate Display Programs
a. The basket’s (tumbler’s) RPM can be displayed by pressing and holding the “DOWN ARROW” key
while a cycle is in progress. If a cycle is not in progress, the board voltage is displayed.
b. The basket (tumbler) temperature and axial temperature (when in Axial Mode) can be displayed by
pressing and holding the “UP ARROW” key at any time.
21
SECTION VI
PROGRAMMING INSTRUCTIONS
A. INTRODUCTION TO PROGRAMMING
The various program selections are stored in the Phase 7.5 non-coin microprocessor controller (computer) and
are broken down into five (5) categories:
0. Language (ENGLISH, FRENCH, SPANISH, ITALIAN, and GERMAN)
1. System Parameters (Dryer Setup, Reversing Setup, and Wrinkle Guard Setup)
2. Preprogrammed Cycles (Key “A-F”)
a. This feature allows the operator to have six (6) most commonly used cycle selections awaiting the push
of a single keyboard (touch pad) entry to start the dryer.
3. Preprogrammed Cycles (“0-40”)
a. This feature allows the operator to have an added forty-one (41) preprogrammed cycle selections.
These can be started by selecting the number and pressing the “START/ENTER”
key.
4. Default Settings (returns ALL the programmable parameters to the default settings)
Both the preprogrammed cycles and the system parameters (programs) have been preprogrammed by the
factory with the parameters shown in Section VII of this manual. The various program selections for the
preprogrammed cycles and system parameters are outlined in Section III of this manual.
ALL program changes for the preprogrammed cycles and system parameters (programs) are done through the
keyboard (touch pad) selection keys on the front of the control panel.
ENTERING THE PROGRAMMING MODE:
First, make sure that no cycle is in progress and that the light emitting diode (L.E.D.) display reads “READY,”
key and the “UP ARROW” key together. This will put you into the
then press the “STOP/CLEAR”
programming mode.
EXITING THE PROGRAMMING MODE:
The “STOP/CLEAR”
key will return you to the previous menu level. Continue to press the
“STOP/CLEAR”
key until you are ALL the way out of the Programming Mode.
To alter the programming parameters, the operator will locate the parameter (program) that is to be changed. If
the change is a numerical one (i.e., time and/or temperature), the operator will simply enter the numerical value
desired. If an error is made, press the “STOP/CLEAR”
key ONCE, and the incorrect entry that was made
will be cancelled. Once the entry is made, and the parameter (program) set does not need to be changed, press
the “START/ENTER”
key and the Phase 7.5 non-coin microprocessor controller (computer) will advance
to the next program selected.
22
If the parameter (program) change is a feature
change, such as changing the temperature
conversion from degree Fahrenheit (ºF) to degree
Celsius (ºC) or from “AUTO” (Automatic Drying
Cycle [Patent No. 4,827,627]) to “MANUAL”
(Timed [Manual] Drying Cycle), the operator will
press and hold the “UP ARROW” or “DOWN
ARROW” key. This will toggle between
choices. Once the entry is made or if the
parameter (program) does not need to be changed,
key and the
press the “START/ENTER”
Phase 7.5 non-coin microprocessor controller
(computer) will advance to the next program
selection.
When making numerical changes, please keep in
mind to stay within the programming limits shown.
If an erroneous entry is made, the Phase 7.5
non-coin microprocessor controller (computer)
will display “ERROR ERROR” and ignore the
entry made when the “START/ENTER”
key
is pressed and will return to the numerical value
previously set.
The Phase 7.5 non-coin microprocessor controller
(computer) allows the operator to scroll through
the various parameters (programs) and select the
parameter to be changed. At this point, the
operator can go to the next Program Location
(system parameter) to be changed. If no other
programs (parameters) need to be changed, the
user can get out of the program mode by pressing
the “STOP/CLEAR”
key until it is out of
the programming mode. The Phase 7.5 non-coin
microprocessor controller (computer) will be
returned to the operating mode, and the light
emitting diode (L.E.D.) display will read
“READY.”
23
B. PROGRAMMING FLOWCHARTS
The following section of this manual explains the programming of the preprogrammed cycles and Program
Locations (system parameters) through the use of flowcharts. A flowchart is nothing more than a diagram of the
programming process.
Four (4) different symbols will be used in these flowcharts:
display symbol
Ready
key symbol
START/ENTER
STOP/CLEAR
Each display symbol will represent a readout on the Phase 7.5 non-coin microprocessor controller (computer)
light emitting diode (L.E.D.) display, and each key symbol will represent a key that is pressed. For example:
1. If the flowchart shows the symbol
L.E.D. display will read the same.
2. If the flowchart shows the symbol
Ready
the Phase 7.5 non-coin microprocessor controller (computer)
you will press that specific key on the keyboard (touch pad) label.
3. This symbol
represents “STOP/CLEAR.”
4. This symbol
represents “START/ENTER.”
a. The flowchart arrows (i.e.,
) represents the program path.
b. On the sides of these flowcharts are explanations of the flowchart procedure, and in some cases the
programming limits.
Listed below, is an index of the flowcharts on the following pages.
Flowchart Titles
Entering and Exiting Program Mode .........................................................................................................
System Parameters (Program):
0 LANGUAGES ...............................................................................................................................
1 SYSTEM PARAMETERS ............................................................................................................
2 “A-F” CYCLE ...............................................................................................................................
3 “0-40” CYCLE ..............................................................................................................................
4 DEFAULT SETTINGS ..................................................................................................................
Page
25
30
31
54
54
62
NOTE: To review the preset Program Locations, simply press the “START/ENTER”
key
followed by the letter location while the L.E.D. display reads “READY.” To review a number
location, simply follow the same process as a letter with the addition of the “START/ENTER”
key being pressed again after the number is selected.
24
PHASE 7.5
MENU PROGRAMMING PROCEDURE
EVERY INDENTED STEP REPRESENTS THE “START/ENTER” KEY BEING PRESSED TO SELECT
A MENU ITEM. EVERY MESSAGE WITH A NUMBER BEFORE IT, INDICATES THAT IT IS A
MENU SELECTION CHOICE. EVERY MESSAGE WITHOUT A NUMBER BEFORE IT, INDICATES
THAT IT IS THE LAST MENU LEVEL.
I.E. MENU FLOW
FROM (“1: SELECT SYSTEM PARAMETERS”)
PRESSING “START/ENTER” PUTS YOU AT (0: DRYER SETUP)
PRESSING “UP ARROW” PUTS YOU AT (1: COOL DOWN SETUP)
PRESSING “DOWN ARROW” PUTS YOU BACK AT (0: DRYER SETUP)
PROGRAMMING MODE:
ENTERING:
MUST BE IN THE “READY” STATE.
PRESS “STOP/CLEAR” AND “UP ARROW” KEY TOGETHER.
(THIS WILL GET YOU INTO THE PROGRAMMING MODE.)
EXITING:
PRESSING THE “STOP/CLEAR” KEY REPEATEDLY UNTIL YOU ARE BACK TO THE “READY”
DISPLAY. THE “STOP/CLEAR” KEY WILL BRING YOU BACK ONE (1) MENU LEVEL AT A
TIME. AT THE FIRST MENU LEVEL, IT WILL EXIT YOU FROM THE PROGRAMMING MODE
AND RETURN TO THE “READY” STATE.
NOTES:
THE “UP ARROW” AND “DOWN ARROW” KEYS ARE USED TO SCROLL UP AND DOWN A
MENU SELECTION.
THE NUMBER KEYS CAN ALSO BE USED TO BRING YOU DIRECTLY TO A KNOWN MENU
ITEM. PRESS THE NUMBER YOU WANT FOLLOWED BY THE “START/ENTER” KEY TO BRING
YOU RIGHT TO THE MENU CHOICE ASSIGNED TO THE NUMBER SELECTED.
25
0: SELECT LANGUAGE
ENGLISH
FRENCH
SPANISH
ITALIAN
GERMAN
1: SELECT SYSTEM PARAMETERS
0: DRYER SETUP
0: SELECT MODEL
GAS REVERSING
ELECTRIC REVERSING
STEAM REVERSING
GAS NON-REVERSING
ELECTRIC NON-REVERSING
STEAM NON-REVERSING
1: SYSTEM TEMP
DEG F
DEG C
(Default GAS REVERSING)
(Default DEG F)
2: ENTER LINT CLEANING FREQUENCY 1 TO 10 HOURS
**
(“**” Displays The Number Chosen. Defaults To “3”)
3: ENTER AUDIO ALERT ON TIMES 0 TO 10
**
(“**” Displays The Number Chosen. Defaults To “5”)
4: ROTATION SENSOR
ON
(Default ON)
OFF
5: AXIAL THERMISTOR INPUT
ON
OFF
(Default OFF)
6: ENTER AXIAL TRIP TEMP 100º TO 400º F
***
(“***” Displays The Number Chosen. Defaults To “180”)
26
1: REVERSING SETUP
NOTE: If a NON-REVERSING model is selected, also display “NOT AVAILABLE.” As soon as
a key is pressed, jump to next location.
0: ENTER SPIN TIME 30 TO 120 SECONDS
(Manually Loaded Manual Cycle Only)
**
(“**” Displays The Number Chosen. Defaults To “60”)
1: ENTER STOP TIME 5 TO 10 SECONDS
(Manually Loaded Manual Cycle Only)
**
(“**” Displays The Number Chosen. Defaults To “5”)
2: WRINKLE GUARD SETUP
0: WRINKLE GUARD AUDIO ALERT
(End Of Wrinkle Guard)
ON
OFF
(Default ON)
2: PROGRAM A-F CYCLES
SELECT A-F KEY
*
SELECT CYCLE TYPE
*
(“*” Displays The Letter Chosen. Defaults To “A”)
(“*” Displays The Cycle Type “Auto” Or “Manual”)
(Default AUTO)
AUTO
0: REVERSE MODE
NOTE: If a NON-REVERSING model is selected, also display “NOT AVAILABLE.” As soon as
a key is pressed, jump to next location.
ON
OFF
(Default ON)
1: ENTER DRY TEMP 160º TO 200º F
(If axial, display “1: DRYING TEMP 150º F ONLY,” then jump to next message)
***
(“***” Displays The Number Chosen. Defaults To “150”)
2: ENTER DRYNESS LEVEL.
FINISHING
DRY
(Default DRY)
EXTRA DRY
3: ENTER CYCLE ADJUSTMENT VALUE 0 TO 99
**
(“**” Displays The Number Chosen. Defaults To “70”)
27
4: CONTROLLED COOL DOWN
ON
OFF
(Default OFF)
5: ENTER COOL DOWN TIME 0 TO 99 MINUTES
NOTE: (If controlled cool down is ON display “NOT AVAILABLE.” As soon as a key is pressed,
jump to the next location.)
**
(“**” Displays The Number Chosen. Defaults To “6”)
6: ENTER COOL DOWN TEMP 70º TO 100º F
***
(“***” Displays The Number Chosen. Defaults To “100”)
NOTE: When Enter is pressed here, jump back to 2: PROGRAM A - F CYCLE
MANUAL
0: REVERSE MODE
NOTE: If a NON-REVERSING model is selected, also display “NOT AVAILABLE.” As soon as
a key is pressed, jump to next location.
ON
OFF
(Default ON)
ENTER SPIN TIME 30 TO 120 SECONDS
***
(“***” Displays The Number Chosen. Defaults To “60”)
ENTER STOP TIME 5 TO 10 SECONDS
**
(“**” Displays The Number Chosen. Defaults To “5”)
Note: When Enter is pressed here, jump to next location.
1: ENTER DRY TIME 0 TO 99 MINUTES
**
(“**” Displays The Number Chosen. Defaults To “0”)
2: ENTER DRY TEMP 100º TO 200º F
(The max temp will be regulated based on axial / radial. Radial = 200º F, Axial = 150º F)
***
(“***” Displays The Number Chosen. Defaults To “100”)
3: CONTROLLED COOL DOWN
ON
OFF
(Default OFF)
4: ENTER COOL DOWN TIME 0 TO 99 MINUTES
NOTE: (If controlled cool down is ON display “NOT AVAILABLE.” As soon as a key is pressed,
jump to the next location.)
**
(“**” Displays The Number Chosen. Defaults To “2”)
28
5: ENTER COOL DOWN TEMP 70º TO 100º F
***
(“***” Displays The Number Chosen. Defaults To “100”)
NOTE: When Enter is pressed here, jump back to 2: PROGRAM A – F CYCLE
3: PROGRAM 0 - 40 CYCLES
ENTER 0 - 40
**
SELECT CYCLE TYPE
*
(“**” Displays The Number Chosen. Defaults To “0”)
(“*” Displays The Cycle Type “Auto” Or “Manual”)
(SEE 2: PROGRAMMING A-F CYCLES)
4: DEFAULT SETTINGS
ENTER PASSWORD
(PRESS “1” “2” “3”)
CONFIRM DEFAULTS.
NO
(Default NO)
YES
NOTE: Selecting “NO” will return you back to “4: DEFAULT SETTINGS.” Selecting “YES” will set
ALL the parameters to the default settings and the display will read “DEFAULTS SET” then
return to “4: DEFAULT SETTINGS.”
29
Selecting Languages
Ready
Press and hold the
stop/clear key
While holding the stop/
clear key, press the up
arrow key.
0:SELECT
LANGUAGE
Press ENTER to access
ENGLISH
Press the up or down arrow
key to select a different
language. ENGLISH,
FRENCH, SPANISH, ITALIAN,
and GERMAN are the
selections.
SPANISH
Press ENTER to store
new changes
1:SELECCIONAR LOS
PARAMETROS DEL SISTEMA
30
Selecting a Dryer Model
While holding the stop/
clear key, press the up
arrow key.
Ready
0:SELECT
LANGUAGE
The computer must be displaying READY
to enter program mode
Press and hold the
stop/clear key
Use arrow
key
Or number
1
Press ENTER to jump
directly to the location
1: SELECT SYSTEM
PARAMETERS
Press ENTER to access
0: DRYER SETUP
Press ENTER to access
0: SELECT
MODEL
Next
page
31
From
Previous
Press ENTER to access
GAS REVERSING
Press the up or down arrow
key to select a different model.
GAS REVERSING, ELECTRIC
REVERSING, STEAM
REVERSING, GAS NONREVERSING, ELECTRIC
NON-REVERSING and
STEAM NON-REVERSING
are the selections.
ELECTRIC
REVERSING
Press ENTER to store
new changes
1: SYSTEM TEMP
32
Selecting the System Temperature
While holding the stop/
clear key, press the up
arrow key.
Ready
0:SELECT
LANGUAGE
Use arrow
key
Press and hold the
stop/clear key
Or number
1
Press ENTER to jump
directly to the location
1: SELECT SYSTEM
PARAMETERS
Press ENTER to access
0: DRYER SETUP
Press ENTER to access
0: SELECT
MODEL
Next
page
33
From
Previous
Use arrow
key
Or number
1
Press ENTER to jump
directly to the location
1: SYSTEM TEMP
Press ENTER to access
DEG F
Press the up or down arrow
key to select DEG F or DEG C
DEG C
Press ENTER to store
new changes
2: ENTER LINT
CLEANING
FREQUENCY 1 TO 10
HOURS
34
Setting the Lint Frequency
While holding the stop/
clear key, press the up
arrow key.
Ready
0:SELECT
LANGUAGE
Press and hold the
stop/clear key
Use arrow
key
Or number
1
Press ENTER to jump
directly to the location
1: SELECT SYSTEM
PARAMETERS
Press ENTER to access
0: DRYER SETUP
Press ENTER to access
0: SELECT
MODEL
Next
page
35
From
Previous
Use arrow
key
Or number
2
1: SYSTEM TEMP
Press ENTER to jump
directly to the location
2: ENTER LINT
CLEANING
FREQUENCY 1 TO 10
HOURS
Press ENTER to access
3
4
Press the up arrow key to increment
the number, down arrow key to
decrement the number or enter the
number directly.
4
Press ENTER to store
new changes
3: ENTER AUDIO ALERT
ON TIMES 0 TO 10
36
Adjusting the Audio Alert On Times
While holding the stop/
clear key, press the up
arrow key.
Ready
0:SELECT
LANGUAGE
Press and hold the
stop/clear key
Use arrow
key
Or number
1
Press ENTER to jump
directly to the location
1: SELECT SYSTEM
PARAMETERS
Press ENTER to access
0: DRYER SETUP
Press ENTER to access
0: SELECT
MODEL
Next
page
37
From
Previous
Use arrow
key
Or number
3
1: SYSTEM TEMP
Press ENTER to jump
directly to the location
2: ENTER LINT
CLEANING
FREQUENCY 1 TO 10
HOURS
3: ENTER AUDIO ALERT
ON TIMES 0 TO 10
Press ENTER to access
5
Next
page
38
From
Previous
3
Press the up arrow key to increment
the number, down arrow key to
decrement the number or enter the
number directly.
3
Press ENTER to store
new changes
4: ROTATION
SENSOR
39
Rotation Sensor
While holding the stop/
clear key, press the up
arrow key.
Ready
0:SELECT
LANGUAGE
Press and hold the
stop/clear key
Use arrow
key
Or number
1
Press ENTER to jump
directly to the location
1: SELECT SYSTEM
PARAMETERS
Press ENTER to access
0: DRYER SETUP
Press ENTER to access
0: SELECT
MODEL
Next
page
40
From
Previous
Use arrow
key
Or number
1: SYSTEM TEMP
4
2: ENTER LINT
CLEANING
FREQUENCY 1 TO 10
HOURS
Press ENTER to jump
directly to the location
3: ENTER AUDIO
ALERT ON TIMES
0 TO 10
4: ROTATION
SENSOR
Next
page
41
From
Previous
Press ENTER to access
ON
Press the up or down arrow
key to select ON or OFF
OFF
Press ENTER to store
new changes
5: AXIAL
THERMISTOR
INPUT
42
Axial Thermistor
While holding the stop/
clear key, press the up
arrow key.
Ready
0:SELECT
LANGUAGE
Press and hold the
stop/clear key
Use arrow
key
Or number
1
Press ENTER to jump
directly to the location
1: SELECT SYSTEM
PARAMETERS
Press ENTER to access
0: DRYER SETUP
Press ENTER to access
0: SELECT
MODEL
Next
page
43
From
Previous
Use arrow
key
Or number
1: SYSTEM TEMP
5
2: ENTER LINT
COUNT 1 TO 5
Press ENTER to jump
directly to the location
3: ENTER AUDIO
ALERT ON TIMES
0 TO 10
4: ROTATION
SENSOR
5: AXIAL
THERMISTOR
INPUT
Next
page
44
From
Previous
Press ENTER to access
OFF
Press the up or down arrow
key to select ON or OFF
ON
Press ENTER to store
new changes
6: ENTER AXIAL
TRIP TEMP 100
TO 400 ºF
45
Axial Thermistor Trip Temperature
While holding the stop/
clear key, press the up
arrow key.
Ready
0:SELECT
LANGUAGE
Press and hold the
stop/clear key
Use arrow
key
Or number
1
Press ENTER to jump
directly to the location
1: SELECT SYSTEM
PARAMETERS
Press ENTER to access
0: DRYER SETUP
Press ENTER to access
0: SELECT
MODEL
Next
page
46
From
Previous
Use arrow
key
Or number
1: SYSTEM TEMP
2: ENTER LINT
CLEANING
FREQUENCY 1 TO 10
HOURS
9
Press ENTER to jump
directly to the location
3: ENTER AUDIO
ALERT ON TIMES
0 TO 10
4: ROTATION
SENSOR
5: AXIAL
THERMISTOR
INPUT
6: ENTER AXIAL
TRIP TEMP 100
TO 400 ºF
Next
page
47
From
Previous
Press ENTER to access
180
2
0
Press the up arrow key to increment
the number, down arrow key to
decrement the number or enter the
number directly.
0
200
Press ENTER to store
new changes
6: ENTER AXIAL
TRIP TEMP 100
TO 400 ºF
48
Adjusting Reversing Spin Time and Stop Time
While holding the stop/
clear key, press the up
arrow key.
Ready
0:SELECT
LANGUAGE
Press and hold the
stop/clear key
Use arrow
key
Or number
1
Press ENTER to jump
directly to the location
1: SELECT SYSTEM
PARAMETERS
Press ENTER to access
0: DRYER SETUP
Use arrow
key
Or number
1
Press ENTER to jump
directly to the location
Next
Page (A)
Next
Page (B)
49
From
Previous
(A)
From
Previous
(B)
1: REVERSING
SETUP
Press ENTER to access
0: ENTER SPIN TIME
30 TO 120 SECONDS
Press ENTER to access
60
7
0
Press the up arrow key to increment
the time, down arrow key to
decrement the time or enter the time
directly. The time is adjustable from
30 to 120 seconds.
70
Press ENTER to store
new changes
1: ENTER STOP TIME
5 TO 10 SECONDS
50
From
Previous
Press ENTER to access
5
7
Press the up arrow key to increment
the time, down arrow key to
decrement the time or enter the time
directly. The stop time is adjustable
from 5 to 10 seconds.
7
Press ENTER to store
new changes
1: ENTER STOP TIME
5 TO 10 SECONDS
51
Wrinkle Guard Audio Alert
While holding the stop/
clear key, press the up
arrow key.
Ready
0:SELECT
LANGUAGE
Press and hold the
stop/clear key
Use arrow
key
Or number
1
Press ENTER to jump
directly to the location
1: SELECT SYSTEM
PARAMETERS
Press ENTER to access
0: DRYER SETUP
Use arrow
key
Or number
2
Press ENTER to jump
directly to the location
1: REVERSING
SETUP
Next
Page (A)
Next
Page (B)
52
From
Previous
(A)
From
Previous
(B)
2: WRINKLE GUARD
SETUP
Press ENTER to access
0: WRINKLE GUARD
AUDIO ALERT
Press ENTER to access
ON
Press the up or down arrow
key to select ON or OFF
OFF
Press ENTER to store
new changes
0: WRINKLE GUARD
AUDIO ALERT
53
Programming A - F Cycles or 0 - 40 Cycles
While holding the stop/
clear key, press the up
arrow key.
Ready
The computer must be displaying READY
to enter program mode
0:SELECT
LANGUAGE
(A - F Cycles)
press up arrow key
twice
Press and hold the
stop/clear key
(0 - 40 cycles)
Press Up arrow
key three times
(A - F Cycles)
Or press 2
(0 - 40 Cycles)
Or press 3
1: SELECT
SYSTEM
PARAMETERS
1: SELECT
SYSTEM
PARAMETERS
2
2: PROGRAM
A - F CYCLES
2: PROGRAM
A - F CYCLES
2: PROGRAM
A - F CYCLES
3: PROGRAM
0 - 40 CYCLES
Next
Page
54
3
3: PROGRAM
0 - 40 CYCLES
Previous
Page
SELECT A - F KEY
or
ENTER 0 - 40
A or 0
Press the key (s) corresponding to the cycle
you wish to program A - F or 0 - 40.
B
Press ENTER to access
SELECT CYCLE
TYPE
AUTO
Follow this flow chart
path for an AUTO cycle
Follow this flow chart path
for a MANUAL cycle
Press the Up or
Down Arrow Key to
change the cycle
type
Press ENTER to store
new changes
0: REVERSE
MODE
MANUAL
Next
Page (A)
Next
Page (B)
55
From
Previous
(A)
From
Previous
(B)
Press ENTER to access
Non reversing
models will display
"NOT AVAILABLE"
and jump to 1:
ENTER DRY
TEMP 160 TO
200ºF
Press ENTER to store
new changes
0: REVERSE
MODE
ON
Press the Up or
Down Arrow Key to
turn reversing ON
or OFF
Press ENTER to access
OFF
OFF
Press the Up or
Down Arrow Key to
turn reversing ON
or OFF
Press ENTER to store
new changes
Axial models will
display 150ºF only
then jump to 2:
ENTER DRYNESS
LEVEL.
Non reversing
models will display
"NOT AVAILABLE"
and jump to
1: ENTER DRY
TIME
1: ENTER DRY TEMP
160 TO 200ºF
ON
Once Enter is
pressed If
reversing is OFF
the program will
jump to
1: ENTER DRY
TIME
Press ENTER to access
ENTER SPIN TIME 30
TO 120 SECONDS
160
60
Next
Page (A)
Next
Page (B)
56
Press the up arrow
key to increment
the temp, down
arrow key to
decrement the
temp or enter the
temp directly.
From
Previous
(A)
From
Previous
(B)
1
4
7
0
Press the up arrow
key to increment
the time, down
arrow key to
decrement the time
or enter the time
directly.
5
40
175
Press ENTER to store
new changes
Press ENTER to store
new changes
ENTER STOP TIME 5
TO 10 SECONDS
2: ENTER
DRYNESS LEVEL
5
Press ENTER to access
7
DRY
7
Next
Page (A)
Next
Page (B)
57
Press the up
arrow key to
increment the
time, down
arrow key to
decrement the
time or enter
the time
directly.
From
Previous
(A)
From
Previous
(B)
Press the up or
down arrow key to
adjust the dryness
level. FINISHING,
DRY OR EXTRA
DRY
Press ENTER to store
new changes
1: ENTER DRY TIME
0 TO 99 MINUTES
EXTRA DRY
Press ENTER to access
Press ENTER to store
new changes
0
3: ENTER CYCLE
ADJUSTMENT
4
Press ENTER to access
Press the up arrow key
to increment the value,
down arrow key to
decrement the value or
enter the value
directly.
5
Press the up arrow
key to increment the
time, down arrow key
to decrement the
time or enter the time
directly.
70
45
7
Press ENTER to store
new changes
5
2: ENTER DRY TEMP
100 TO 200 ºF
Next
Page (A)
Next
Page (B)
58
Axial models will
display a maximum
temp of 150 ºF
From
Previous
(A)
From
Previous
(B)
75
Press ENTER to access
Press ENTER to store
new changes
100
4: CONTROLLED
COOL DOWN
1
Press ENTER to access
7
OFF
5
Press the up or
down arrow key to
turn the option ON
or OFF.
175
Press the up arrow
key to increment
the temp, down
arrow key to
decrement the
temp or enter the
temp directly.
Press ENTER to store
new changes
ON
3: CONTROLLED
COOL DOWN
Press ENTER to store
new changes
Press ENTER to access
5: ENTER COOL DOWN
TIME 0 TO 99 MINUTES
Next
Page (A)
Next
Page (B)
59
Press ENTER to access.
If CONTROLLED COOL
DOWN is ON the program
will display NOT
AVAILABLE. Press
ENTER to access
5: ENTER COOL DOWN
TEMP 70 to 100º
Press the up arrow key
to increment the time,
down arrow key to
decrement the time or
enter the time directly.
From
Previous
(A)
From
Previous
(B)
OFF
Press the up or down
arrow key to turn the
option ON or OFF.
2
ON
Press ENTER to store
new changes
5
Press ENTER to access.
If CONTROLLED COOL
DOWN is ON the program
will display NOT
AVAILABLE. Press
ENTER to access
5: ENTER COOL DOWN
TEMP 70 to 100º
4: ENTER COOL DOWN
TIME 0 TO 99 MINUTES
5
Press ENTER to store
new changes
2
6: ENTER COOL DOWN
TEMP 70 TO 100 ºF
Press ENTER to access
5
80
Next
Page (A)
Next
Page (B)
60
Press the up arrow key
to increment the time,
down arrow key to
decrement the time or
enter the time directly.
From
Previous
(A)
Press the up arrow key
to increment the temp,
down arrow key to
decrement the temp or
enter temp directly.
From
Previous
(B)
5
Press ENTER to store
new changes
8
5: ENTER COOL DOWN
TEMP 70 TO 100 ºF
5
Press ENTER to access
Press the up arrow
key to increment the
temp, down arrow
key to decrement the
temp or enter temp
directly.
85
100
Press ENTER to store
new changes
8
2: PROGRAM A-F CYCLES
or
3: PROGRAM 0-40 CYCLES
0
Program jumps back to
2:PROGRAM A-F CYCLES or
3:PROGRAM 0-40 CYCLES.
80
Press ENTER to store
new changes
2: PROGRAM A-F CYCLES
or
3: PROGRAM 0-40 CYCLES
Program jumps back to
2:PROGRAM A-F CYCLES or
3:PROGRAM 0-40 CYCLES.
61
Restoring Factory Default Settings
While holding the stop/
clear key, press the up
arrow key.
Ready
0:SELECT
LANGUAGE
The computer must be displaying READY
to enter program mode
Press and hold the
stop/clear key
Or number
Use arrow
key
1: SELECT
SYSTEM
PARAMETERS
4
2: PROGRAM
A - F CYCLES
Press ENTER to jump
directly to the location
3: PROGRAM
0 - 40 CYCLES
4: DEFAULT
SETTINGS
Next
page
62
From
Previous
ENTER
PASSWORD
1
2
3
CONFIRM
DEFAULTS
NO
Press the Up or Down Arrow
Key to toggle from NO to YES
Next
page
63
From
Previous
YES
WARNING: Pressing enter will
restore factory default settings
including all preprogrammed
cycles and any adjustments
made to programming.
DEFAULTS SET
4: DEFAULT
SETTINGS
64
SECTION VII
FACTORY PRESET PARAMETERS (PROGRAMS)
NOTE: To enter program mode press and hold the stop
and press the
up arrow.
A. CYCLE “A-F” PARAMETERS (PROGRAMS) PRESET BY THE FACTORY
CYCLE A:
SELECT CYCLE TYPE = AUTO, 0:REVERSE MODE = ON, 1:ENTER DRY TEMP = 180°F, 2:ENTER
DRYNESS LEVEL = EXTRA DRY, 3:ENTER CYCLE ADJUSTMENT VALUE = 70, 4:CONTROLLED
COOL DOWN = OFF, 5:ENTER COOL DOWN TIME = 6 MINUTES, 5:ENTER COOL DOWN TEMP =
80°F
CYCLE B:
SELECT CYCLE TYPE = AUTO, 0:REVERSE MODE = ON, 1:ENTER DRY TEMP = 180°F, 2:ENTER
DRYNESS LEVEL = DRY, 3:ENTER CYCLE ADJUSTMENT VALUE = 70, 4:CONTROLLED COOL
DOWN = OFF, 5:ENTER COOL DOWN TIME = 6 MINUTES, 5:ENTER COOL DOWN TEMP = 80°F
CYCLE C:
SELECT CYCLE TYPE = AUTO, 0:REVERSE MODE = ON, 1:ENTER DRY TEMP = 160°F, 2:ENTER
DRYNESS LEVEL = DRY, 3:ENTER CYCLE ADJUSTMENT VALUE = 70, 4:CONTROLLED COOL
DOWN = OFF, 5:ENTER COOL DOWN TIME = 4 MINUTES, 5:ENTER COOL DOWN TEMP = 80°F
CYCLE D:
SELECT CYCLE TYPE = MANUAL, 0:REVERSE MODE = ON, ENTER SPIN TIME = 60 SECONDS,
ENTER STOP TIME = 5 SECONDS, 1:ENTER DRY TIME = 40 MINUTES, 2:ENTER DRY TEMP = 190°F,
3:CONTROLLED COOL DOWN = OFF, 4:ENTER COOL DOWN TIME = 6 MINUTES, 5:ENTER COOL
DOWN TEMP = 80°F
CYCLE E:
SELECT CYCLE TYPE = MANUAL, 0:REVERSE MODE = ON, ENTER SPIN TIME = 60 SECONDS,
ENTER STOP TIME = 5 SECONDS, 1:ENTER DRY TIME = 30 MINUTES, 2:ENTER DRY TEMP = 180°F,
3:CONTROLLED COOL DOWN = OFF, 4:ENTER COOL DOWN TIME = 4 MINUTES, 5:ENTER COOL
DOWN TEMP = 80°F
CYCLE F:
SELECT CYCLE TYPE = MANUAL, 0:REVERSE MODE = ON, ENTER SPIN TIME = 60 SECONDS,
ENTER STOP TIME = 5 SECONDS, 1:ENTER DRY TIME = 10 MINUTES, 2:ENTER DRY TEMP = 170°F,
3:CONTROLLED COOL DOWN = OFF, 4:ENTER COOL DOWN TIME = 2 MINUTES, 5:ENTER COOL
DOWN TEMP = 80°F
NOTE: When in Axial Mode, temperature for ALL cycles is limited to 150º F (66º C) ONLY.
65
B. CYCLE “0-40” PARAMETERS (PROGRAMS) PRESET BY THE FACTORY
CYCLE “0-40”:
Manual (Timed) Mode, Reverse, Dry Time = 0, Dry Temp = 100, Cool Down Time = 4 Minutes, Cool Down
Temp = 100, Spin Time = 60, Stop Time = 7.
66
SECTION VIII
PHASE 7.5 NON-COIN PROGRAMMING LIMITS
A. PREPROGRAMMED CYCLES
1. Automatic Drying Cycle (Patent No. 4,827,627)
a. Drying Temperature from 160º F to 200º F (71º C to 93º C) in one-degree increments.
b. Cycle Adjustment Value from 0-99 in increments of one (1).
c. Cool Down Time from 0 to 99 minutes in 1 minute increments.
d. Cool Down Temperature from 70º F to 100º F (21º C to 38º C) in one-degree increments.
2. Timed (Manual) Drying Cycle
a. Drying Temperature from 100º F to 200º F (38º C to 93º C) in one-degree increments.
b. Drying Time from 0 to 99 minutes in 1 minute increments.
c. Cool Down Time from 0 to 99 minutes in 1 minute increments for preprogrammed cycle.
d. Cool Down Temperature from 70º F to 100º F (21º C to 38º C) in one-degree increments.
e. Reversing Models
1) Automatic Drying Cycle (Patent No. 4,827,627) Spin Time and Stop Time is not programmable.
(Refer to Fixed Parameters on next page).
2) Manual Timed Cycle
a) Spin Time (“SPIN TIME”) from 30-seconds to 120-seconds in 1-second increments.
b) Stop Time (“STOP TIME”) from 5-seconds to 10-seconds in 1-second increments.
67
B. SYSTEM PARAMETERS (PROGRAM LOCATIONS)
1. Cycle Adjustment Value from 0 to 99 in increments of one (1).
2. Manually Loaded Auto Cycle (“COOL DOWN TIME”) from 0 to 99 minutes in 1 minute increments.
3. Audio Alert 0-10.
4. Lint Cleaning Frequency 1 to 10 hours.
C. FIXED PARAMETERS
1. Spin Time (“SPIN TIME”) is fixed at 2 minutes in forward and 2 minutes in reverse.
2. Stop Time (“STOP TIME”) is fixed at 5-seconds (in the Auto Mode) and is not adjustable.
68
SECTION IX
PHASE 7.5 AUTO CYCLE (PATENT NO. 4,827,627)
CYCLE ADJUSTMENT VALUES
GAS
ELECTRIC
STEAM
MODEL
Adjustment
Value
MODEL
Adjustment
Value
MODEL
Adjustment
Value
AD\CG\D\SL-20
69
AD\CG\D\SL-20
69
ADS-30
68
ADG-30
68
ADE-30
68
ADS-60
65
ADG-50
70
ADE-50
70
ADS-75
70
ADG-60
65
ADE-60
65
ADS-115
68
ADG-75
70
ADE-75
70
ADS-120ES
65
ADG-78
70
ADE-115
60
ADS-170ES
70
ADG-81
70
ADE-120ES
78
MLS-55
65
MLE-55
65
MLS-75
70
70
EURO-14
68
78
EURO-24
70
EURO-35
70
ADG-115D
68
ADG-120ES
73
ADG-170SE
68
MLG-55
65
EURO-14
68
MLG-75
70
EURO-24
70
MLG-78
70
EURO-35
70
MLG-82
70
MLG-96
70
MLG-122
70
MLG-130
73
MLG-170/175
68
MLG-190
70
EURO-14
68
EURO-24
70
EURO-35
70
MLE-75
MLE-120ES
IMPORTANT: If your particular model/dryer dryness levels are not shown in the above charts,
contact the ADC Service Department for the appropriate factors for your particular
dryer. When doing so, please have the dryer model and serial numbers available.
IMPORTANT: The adjustment values have been preprogrammed by the factory, but can be changed
in the field. If the Phase 7.5 non-coin microprocessor controller (computer) should
fail and is being replaced. THE REPLACEMENT PHASE 7.5 NON-COIN
MICROPROCESSOR CONTROLLER (COMPUTER) MUST BE
REPROGRAMMED FOR THE SPECIFIC MODEL SHOWN IN THE
ADJUSTMENT VALUE PARAMETERS CHARTS ABOVE. THE
ADJUSTMENT VALUE LABEL IS LOCATED ON THE CONTROL
PANEL, BEHIND THE PHASE 7.5 KEYBOARD (TOUCH PAD) DISPLAY
DOOR.
NOTE: When fine-tuning the Auto Cycle for certain loads, if the material comes out wet, decrease the
adjustment value, if the material comes out too dry, increase the adjustment value.
69
SECTION X
PHASE 7.5 NON-COIN SYSTEM DIAGNOSTICS
IMPORTANT: YOU MUST DISCONNECT AND LOCKOUT THE ELECTRIC SUPPLY
AND THE GAS SUPPLY OR THE STEAM SUPPLY BEFORE ANY
COVERS OR GUARDS ARE REMOVED FROM THE MACHINE TO
ALLOW ACCESS FOR CLEANING, ADJUSTING, INSTALLATION, OR
TESTING OF ANY EQUIPMENT PER OSHA (Occupational Safety and Health
Administration) STANDARDS.
ALL major circuits, including door, microprocessor temperature sensor, heat and motor circuits are monitored.
The Phase 7.5 non-coin microprocessor controller (computer) will inform the user, via the light emitting diode
(L.E.D.) display of certain failure messages, along with L.E.D. indicators on the Input/Output (I/O) board on the
back panel of the front right control door.
A. DIAGNOSTIC (L.E.D. DISPLAY) FAULT MESSAGES
MAIN DOOR OPENED – A main door is open when it should be closed.
EXHAUST HIGH TEMP FAULT – Indicates the temperature in the basket (tumbler) is above 220º F
(104º C).
LINT ACCESS OPEN – Indicates the lint drawer is open and needs to be closed.
EXHAUST HIGH LIMIT FAULT – Indicates the temperature disk in the exhaust has opened.
SAIL SWITCH CLOSED FAULT – Sail switch is closed and should be opened.
SAIL SWITCH OPEN FAULT – Sail switch is open and should be closed.
BURNER HIGH LIMIT FAULT – Indicates the temperature disk in the burner has opened.
BURNER CONTROL FAULT – No signal to gas valve from Direct Spark Ignition (DSI) module during trial
for ignition time.
IGNITION FAULT – Gas valve did not remain open after trial for ignition. Indicates that no flame was
detected.
FLAME FAULT – Indicates flame was detected during trial for ignition but failed sometime after. This
condition must reoccur for five (5) retries before fault occurs.
ROTATION FAULT – Indicates the basket (tumbler) is not rotating.
EXHAUST PROBE FAULT – Indicates the exhaust temperature probe is open or shorted.
LOW VOLTAGE FAULT – Indicates power has dropped below the operating values and will shutdown.
AXIAL PROBE FAULT- Indicates the axial temperature probe is open or shorted.
70
BURNER PURGE FAULT – The gas valve signal is present during the prepurge time.
MODEL ERROR, ENTER CORRECT MODEL – The wrong model was selected for the dryer.
EE PROM FAULT ### – Error in memory location. The ### indicates the location of the fault.
S.A.F.E. SYSTEM ACTIVATED – Indicates that the control has detected a fire and is currently extinguishing
the flame.
S.A.F.E. SYSTEM WAS ACTIVATED – Indicates that the control detected a fire and has extinguished the
flame.
B. S.A.F.E. SYSTEM DIAGNOSTIC CONDITIONS
In the event that the Phase 7.5 non-coin microprocessor controller (computer) detects a fault in the Sensor
Activated Fire Extinguishing (S.A.F.E.) system, the control will display the message “S.A.F.E. SYSTEM
DISABLED … READY.” To find out the reason for the S.A.F.E. system disabling, press and hold the red
“STOP/CLEAR” and green “START” keys. This will cause the control to display one (1) of the following
diagnostic messages.
OPEN THERMISTOR PROBE – This message indicates that the S.A.F.E. system thermistor probe is either
not connected or is damaged. If this condition is detected, the Phase 7.5 non-coin control will immediately enter
S.A.F.E. SYSTEM DISABLED mode.
SHORTED THERMISTOR PROBE – This message indicates that the S.A.F.E. system thermistor probe is
damaged or the wiring is shorted. If this condition is detected, the Phase 7.5 non-coin control will immediately
enter S.A.F.E. SYSTEM DISABLED mode.
DISCONNECTED WATER VALVE – This indicates that the water valve is open or that it is not connected
to the control. If this condition is detected, the Phase 7.5 non-coin control will continue to monitor the condition
for a period of 5 minutes before entering S.A.F.E. SYSTEM DISABLED mode. Once the condition is corrected,
the control will continue to monitor the condition for 1 minute before exiting S.A.F.E. SYSTEM DISABLED
mode.
SHORTED WATER VALVE – This indicates the water valve is shorted or the wiring to the valve is shorted.
If this condition is detected, the Phase 7.5 non-coin control will continue to monitor the condition for a period of
5 minutes before entering S.A.F.E. SYSTEM DISABLED mode. Once the condition is corrected, the control
will continue to monitor the condition for 1 minute before exiting S.A.F.E. SYSTEM DISABLED mode.
WATER NOT CONNECTED – This indicates that there is no water pressure at the water valve. This will
occur if water is not connected to the dryer or if there is low water pressure in the water line coming to the dryer.
This could also be a defective pressure switch or wiring to the pressure switch. If this condition is detected, the
Phase 7.5 non-coin control will continue to monitor the condition for a period of 5 minutes before entering
S.A.F.E. SYSTEM DISABLED mode. Once the condition is corrected, the control will continue to monitor the
condition for 1 minute before exiting S.A.F.E. SYSTEM DISABLED mode.
71
C. INPUT/OUTPUT (I/O) BOARD LIGHT EMITTING DIODE (L.E.D.)
INDICATORS
1. INPUTS
1. ESTOP – (RED L.E.D.) This L.E.D. will indicate the status of the E-STOP. If the E-STOP has been
pressed, then the L.E.D. is ON.
2. GAS_V – (RED L.E.D.) This L.E.D. will indicate the status of the gas valve. If the gas valve is open
(ON), then the L.E.D. is ON.
3. BRHL – (RED L.E.D.)
This L.E.D. will indicate the status of the burner high limit disk. If the disk is
closed (temperature below 330º F [166º C]), then the L.E.D. is ON.
4. SAIL – (RED L.E.D.)
This L.E.D. will indicate the status of the sail switch. If the switch is closed, then
the L.E.D. is ON.
5. EXHL – (RED L.E.D.)
This L.E.D. will indicate the status of the exhaust high limit disk. If the disk is
closed (temperature below 225º F [107º C]), then the L.E.D. is ON.
6. MAIN – (RED L.E.D.) This L.E.D. will indicate the status of the main door. If the door is closed, then
the L.E.D. is ON.
7. LINT – (RED L.E.D.)
This L.E.D. will indicate the status of the lint drawer. If the drawer is closed,
then the L.E.D. is ON.
8. FUSE – (RED L.E.D.)
This L.E.D. will indicate the status of the control voltage. If the POWER ON
button is pressed (green button light is on), then the L.E.D. is ON.
9. H2O – (RED L.E.D.)
This L.E.D. will indicate the status of water pressure switch on the Sensor
Activated Fire Extinguishing (S.A.F.E.) system water line. If water pressure is
present, then the L.E.D. is ON.
2.
OUTPUTS
10. F.S.S. – (GREEN L.E.D.)
This L.E.D. will indicate the F.S.S./S.A.F.E. system output is activated.
11. HEAT – (GREEN L.E.D.)
This L.E.D. will indicate the status of the heat output. If the request to turn
on the heater is made, then the L.E.D. is ON.
12. REV – (GREEN L.E.D.)
This L.E.D. will indicate the status of the basket (tumbler) reverse direction
output. If the request to tumble the drum in the reverse direction is made,
then the L.E.D. is ON.
13. FWD – (GREEN L.E.D.)
This L.E.D. will indicate the status of the basket (tumbler) forward direction
output. If the request to tumble the drum in the forward direction is made,
then the L.E.D. is ON.
14. FAN – (GREEN L.E.D.)
This L.E.D. will indicate the status of the fan output. If the request to turn on
the fan (blower) is made, then the L.E.D. is ON.
72
D. KEYBOARD (TOUCH PAD) LAYOUT
1. Dot Matrix Display
2. A-F Preprogrammed Cycles
3. Stop/Pause Button
4. Start Button
5. Increment Button
6. Decrement Button
7. One time Auto (Dryness level)
and Manual (timed) Cycle
NOTE: Fuse 1 (F1) is a self-resetting upon power cycle. If fuse 1 is opened, the display will be
blank. Fuse 2 (F3) is for 24V control power rated at 5-amps. If fuse 2 blows it is a 24V
control fault.
73
SECTION XI
CUSTOMER CUSTOM PARAMETER SETTINGS
This section is set aside for customer use where customer or specific parameters/settings can be documented,
as programmed by them for their specific dryer. It is suggested that any parameter changes or customer cycles
be documented here for future reference.
CUSTOMER USE
LANGUAGE:
_________________________
MODEL:
_________________________
SYSTEM TEMP:
_________________________
DRYNESS LEVEL:
_________________________
LINT COUNT:
_________________________
AUDIO ALERT:
_________________________
SPIN TIME:
_________________________
STOP TIME:
_________________________
WRINKLE GUARD AUDIO ALERT:
_________________________
1ST ON TIME:
_________________________
OFF TIME:
_________________________
2ND ON TIME:
_________________________
OFF TIME:
_________________________
3RD ON TIME
_________________________
OFF TIME:
_________________________
4TH ON TIME:
_________________________
OFF TIME:
_________________________
5TH ON TIME:
_________________________
OFF TIME:
_________________________
74
PROGRAMMED CYCLE A-F:
Cycle:
______________________
Cycle Type: AUTO
Reverse Mode:
__________________ (Option)
Dry Temp:
_________________________
Dry Level:
_________________________
Cool Down Time:
_________________________
Cool Down Temp:
_________________________
Controlled Cool Down:
_________________________
Cycle Type: MANUAL
Reverse Mode:
__________________ (Option)
Dry Time:
_________________________
Dry Temp:
_________________________
Cool Down Time:
_________________________
Cool Down Temp:
_________________________
Spin Time:
_________________________
Stop Time:
_________________________
Controlled Cool Down:
_________________________
1ST ON TIME:
_________________________
OFF TIME:
_________________________
2ND ON TIME:
_________________________
OFF TIME:
_________________________
3RD ON TIME
_________________________
OFF TIME:
_________________________
4TH ON TIME:
_________________________
OFF TIME:
_________________________
5TH ON TIME:
_________________________
OFF TIME:
_________________________
75
PROGRAMMED CYCLE 0-40:
Cycle:
______________________
Cycle Type: AUTO
Reverse Mode:
__________________ (Option)
Dry Temp:
_________________________
Dry Level:
_________________________
Cool Down Time:
_________________________
Cool Down Temp:
_________________________
Controlled Cool Down:
_________________________
Cycle Type: MANUAL
Reverse Mode:
__________________ (Option)
Dry Time:
_________________________
Dry Temp:
_________________________
Cool Down Time:
_________________________
Cool Down Temp:
_________________________
Spin Time:
_________________________
Stop Time:
_________________________
Controlled Cool Down:
_________________________
1ST ON TIME:
_________________________
OFF TIME:
_________________________
2ND ON TIME:
_________________________
OFF TIME:
_________________________
3RD ON TIME
_________________________
OFF TIME:
_________________________
4TH ON TIME:
_________________________
OFF TIME:
_________________________
5TH ON TIME:
_________________________
OFF TIME:
_________________________
76
ADC 113196
1 - 07/16/03-25
2 * 09/03/03-25