IQAN-LC5-C0x
Instruction book
Publ no: HY33-8404-IB/UK
Edition: 2013-08-09
Contents
Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Overview of relevant documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
General safety regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Construction regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety during installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety during start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety during maintenance and fault diagnosis . . . . . . . . . . . . . . . . . . . 4
3
Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
IQAN-LC5-C0x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
The control lever's parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
The IQAN-LC5-C0x control signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
I/O overview -C01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Directional Analogue Channels (DAC) . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
IQAN-LC5-C0x CAN related functions . . . . . . . . . . . . . . . . . . . . . . . . . . 8
IQAN-LL replacement / IQAN-LC5-C02 . . . . . . . . . . . . . . . . . . . . . . . . . 8
MP handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
The handle's parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
I/O overview, MP handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Buttons and thumbwheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Redundant signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Internal diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
CAN-bus interruption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Deadband . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Magnetic Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Mounting the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Mounting considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Mounting methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Handle considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Recommended handle specification . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Environmental specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
IQAN-LC5-C0x connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connector C1 pin assignments (-C01 & -C02) . . . . . . . . . . . . . . . . . . . . . . . 14
Connector C2 pin assignments (-C01) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Connector C3 pin assignments (-C01) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Connector C2 pin assignments (-C02) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Connector C3 pin assignments (-C02) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
MP handle connector, 6 position for C3 connection . . . . . . . . . . . . . . . . . . . 17
Connector, 6 position assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
MP handle connector, 12 position for C2 connection . . . . . . . . . . . . . . . . . . 18
Connector, 12 position assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Instruction book, IQAN-LC5-C0x
ii
Contents
Connector, 12 position assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Required connectors, based on model code . . . . . . . . . . . . . . . . . . . . . 20
MP handle faceplate function numbering. . . . . . . . . . . . . . . . . . . . . . . 20
IQAN-LC5-C01 supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Emergency stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Connecting of supply voltage, -C0x . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Polarity reversal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
IQAN-LC5-C0x addressing/terminating . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Terminating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Reference voltage, VREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Connecting sensors and switches to IQAN-LC5-C01 . . . . . . . . . . . . . . . . . 24
Connecting sensors to the voltage inputs . . . . . . . . . . . . . . . . . . . . . . . 24
7
Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Start-up procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Starting the control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Prepare for system start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Start the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
8
System Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Appendix A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
IQAN-LC5-C0x Technical Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
IQAN-LC5-C01, base and -MP handle . . . . . . . . . . . . . . . . . . . . . . . . . 28
IQAN-LC5-C01, -MP handle only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Thumbwheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Appendix B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Error codes, messages and actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
LED indicator showing different IQAN-LC5-C0x modes . . . . . . . . . . . . 32
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Appendix C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Dimensioning of the IQAN-LC5-C0x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Dimensioning of the IQAN-LC5 with MP handle . . . . . . . . . . . . . . . . . . . . . 35
Instruction book, IQAN-LC5-C0x
iii
1
Introduction
Warnings
1
Introduction
These instructions are to be used as a reference tool for the vehicle manufacturer’s
design, production, and service personnel.
The user of these instructions should have basic knowledge in the handling of
electronic equipment.
Warnings
Sections marked with a symbol in the left margin, must be read and understood by
everyone using the system, carrying out service work, or making changes to hardware
and software.
The different symbols used in this manual are defined below.
WARNING
Sections labeled WARNING with a caution symbol in the left margin, indicate that a
hazardous situation exists. We use warnings, marked with the warning symbol, in two
ways.
• As a strong recommendation about work practices when using the product in the
machine (e.g. routines when updating an application). This use is common to the
term 'hazardous situation', that a person is exposed to a hazard.
• As a way of pointing out important information for the machine designer that in
some way relates to safety. This includes the design of the physical machine, and
also the application program being developed for the control system.
Not all document sections that contain information about safety are marked with a
warning symbol (there would be warnings everywhere). Failure to comply with the
recommendations can cause unintentional, and unexpected behavior of the control
system. This can potentially cause death, serious injury or property damage.
N OTICE
Sections labeled NOTICE with a notice symbol in the left margin, indicate there is
important information about the product. Ignoring this could result in less than optimal
performance, or damage to the product.
Contact the manufacturer if there is anything you are not sure about or if you have any
questions regarding the product and its handling or maintenance.
The term "manufacturer" refers to Parker Hannifin Corporation.
Instruction book, IQAN- LC5-C0x
1
Overview of relevant documentation
1
Introduction
Overview of relevant documentation
The following publications are relevant for users of this product.
The main documentation contains information that is not found elsewhere.
The additional documentation contains product information in a compact format, for
details on the information found in those documents, consult this manual.
Main
Documentation
Compact
Documentation
IQANdesign
User Manual
IQAN-LC5-C0x Instruction Book
HY33-8404-IB
(this book)
IQAN-LC5-C0x
Catalogue Datasheet
HY33-8404
IQAN-LC5-C01
Installation Sheet
HY33-8404-IS
Mounting and Maintenance
Instruction Book
HY33-8327-IB
IQAN-LC5-C01
Electrical Schematic
HY33-8404-ES
OR
IQAN-LC5-C02
Installation Sheet
HY33-8405-IS
The IQAN-LC5-C0x module documentation system.
2
Instruction book, IQAN- LC5-C0x
2
General safety regulations
2
2
Precautions
Precautions
General safety regulations
Work on the hydraulics control electronics may only be carried out by trained
personnel who are well-acquainted with the control system, the machine and its safety
regulations.
WARNING
Mounting, modification, repair and maintenance must be carried out in accordance
with the manufacturer's regulations. The manufacturer has no responsibility for any
accidents caused by incorrectly mounted or incorrectly maintained equipment. The
manufacturer does not assume any responsibility for the system being incorrectly
applied, or the system being programmed in a manner that jeopardizes safety.
WARNING
Damaged product may not be used. If the control system shows error functions or if
electronic modules, cabling or connectors are damaged, the system shall not be used.
WARNING
Electronic control systems in an inappropriate installation and in combination with
strong electromagnetic interference fields can, in extreme cases, cause an unintentional
change of speed of the output function.
N OTICE
As much as possible of the welding work on the chassis should be done before the
installation of the system. If welding has to be done afterwards, the electrical
connections on the system must be disconnected from other equipment. The negative
cable must always be disconnected from the battery before disconnecting the positive
cable. The ground wire of the welder shall be positioned as close as possible to the
place of the welding. The cables on the welding unit shall never be placed near the
electrical wires of the control system.
Construction regulations
WARNING
The vehicle must be equipped with an emergency stop which disconnects the supply
voltage to the control system's electrical units. The emergency stop must be easily
accessible to the operator. The machine must be built if possible, so that the supply
voltage to the control system's electrical units is disconnected when the operator leaves
the operator’s station.
Safety during installation
WARNING
Incorrectly positioned or mounted cabling can be influenced by radio signals which can
interfere with the functions of the system.
3
Instruction book, IQAN- LC5-C0x
3
General safety regulations
2
Precautions
Safety during start-up
WARNING
The machine's engine must not be started before the control system is mounted and its
electrical functions have been verified.
Ensure that no one is in front, behind or nearby the machine when first starting up the
machine.
Follow the instructions for function control in the Start-up section.
Safety during maintenance and fault diagnosis
WARNING
Ensure that the following requirements are fulfilled before any work is carried out on
the hydraulics control electronics.
• The machine cannot start moving.
• Functions are positioned safely.
• The machine is turned off.
• The hydraulic system is relieved from any pressure.
• Supply voltage to the control electronics is disconnected.
4
Instruction book, IQAN- LC5-C0x
4
IQAN-LC5-C0x
3
3
Product description
Product description
IQAN-LC5-C0x
The CAN joystick replaces IQAN-LL (fourth generation) coordinate levers and
therefore is called IQAN-LC5 (Lever, Coordinate 5th generation). The designation C01 (CANbus, type 01) represents the CAN version. The joystick version -C02 is
configured to be a drop-in replacement for the IQAN-LL-2U.
1
2
3
4
7
6
8
5
-C01/-C02
The IQAN-LC5-C0x parts
The control lever's parts
Control lever -LC5-C0x consists of:
1 Stem, -U2 shown, no handle mounted, (-H1 ball knob, will fit to stem).
2 Bellows, -U2 shown, no handle mounted, (other bellows for -H1 ball knob).
3 Mounting flange.
4 Lower enclosure.
5 Connector C1 for CAN bus, supply voltage, address idTag (-C01, -C02).
6 Connector C2 for inputs and outputs (-C01, -C02).
7 Connector C3 for inputs and outputs (-C01, -C02).
8 Indicator for supply voltage and status (-C01, -C02).
5
Instruction book, IQAN- LC5-C0x
5
I/O overview -C01
3
Product description
The IQAN-LC5-C0x control signals
The IQAN-LC5-C0x is used to control the object in two directions:
• the lever is moved to the right/left, direction X +/-.
• the lever is moved forward/back, direction Y +/-.
The control signal is proportional to the lever's working range.
The control signal is transferred internally from the IQAN-LC5-C0x via the CAN bus
to the IQAN master unit. The control signal's data is treated in the system and is then
available as an output signal, for example in the expansion unit IQAN-XA2.
The IQAN-LC5-C01 has three Deutsch DTM connectors built into its base. Connector
C1 is a 6 position connector for power, CAN and addressing of the joystick. Connector
C2 is a 12 position connector for internal and external analog or digital signals, which
may come from the handle of the joystick, or from other input devices in an armrest or
panel. Connector C3 is an additional 6 position connector that will provide VREF for
external sensors and accepts 4 external analog inputs.
IQAN-LC5-C01 joysticks
IQAN-MDL2
Expansion units
IQAN-LC5-C01 in a typical system
I/O overview -C01
+BAT
ADDR-H
-BAT
ADDR-L
+VREF
-VREF
+VREF
-VREF
LC5
-C01
CAN-H
CAN-L
1x DOUT
8x VIN
5x DIN
6
Instruction book, IQAN- LC5-C0x
6
I/O overview -C01
3
Product description
Directional Analogue Channels (DAC)
The IQAN-LC5-C01 joystick has five (5) directional analogue channels for use in
IQAN applications. These are assigned to X-axis, Y-axis and up to three additional
proportional command signals denoted as Z1 thru Z3 (when the -MP handle is used).
The DAC channels are sent to the master unit via CAN and defined using IQAN
software.
Command
Ax
is
DA
C
+100%
0%
-100%
Deflection
100%
Neutral
position
100%
IQAN-LC5-C0x DAC channel
(2) Coordinate DAC outputs DAC-X and DAC-Y (internal, not in connectors)
(3) Auxiliary DAC outputs DAC-Z1 thru DAC-Z3 (external, via C2/C3 connectors)
Joystick Deadband X, Y
The unit has a built in deadband of 5%. During the lifetime of the unit, the mechanical
wear on the joystick may require a total deadband of 10%.
Command
Ax
is
DA
C
+100%
0%
-100%
-FS
5% 5%
Neutral
position
Deflection
+FS
IQAN-LC5-C0x default deadband
To allow for wear over the life of the joystick, an additional 5 % should be added to the
deadband in the application.
Command
Ax
is
DA
C
+100%
0%
-100%
-FS
10%
10%
Neutral
position
Deflection
+FS
IQAN-LC5-C0x minimum recommended deadband
7
Instruction book, IQAN- LC5-C0x
7
I/O overview -C01
3
Product description
Inputs
The IQAN-LC5-C01 module has eight (8) voltage inputs in the C2/C3 connectors for
internal (-MP handle) or external signals.
(8) Voltage inputs VIN-A thru VIN-H
There are five (5) digital inputs in the C2 connector for external signals.
(5) Digital inputs DIN-A thru DIN-E
Outputs
For the IQAN-LC5-C01 there is one (1) digital output, DOUT-A.
(1) Digital output DOUT-A
The digital ouput is intended for loads like warning lamps or audible signals.
Connection of DOUT
Connect the alarm (audio signal) between pin C2:7 and -BAT (the battery’s negative
pole). See the illustration below. An active output gives battery voltage (9-32 Vdc) to
the pin. The maximum load is 200 mA.
IQAN-LC5-C0x
DOUT
Connection of DOUT as an alarm output.
IQAN-LC5-C0x CAN related functions
The master unit uses a CAN-bus (CAN = Controller Area Network) to communicate
with the IQAN-LC5-C0x module. The CANbus is a robust communication protocol
that is widely used and well proven within the automotive industry.
IQAN-LL replacement / IQAN-LC5-C02
For existing installations with fourth generation joystick, IQAN-LL, there is a
compatible configuration based on the IQAN-LC5-C01. The IQAN-LC5-C02 has three
connectors built into its base. Connector C1 with 6 positions is for power, CAN and
addressing of the joystick. Connector C2 with 12 positions is used to connect the
IQAN-LL external I/O to the IQAN-LC5-C02. Connector C3 is an additional 6
position connector that is used for the possible existing IQAN-LL handle functions. An
adapter harness is available to make retrofitting simpler for the end-user.
N OTICE
Use IQAN-LC5-C01 for new applications.
The IQAN-LC5-C02 is meant for service part usage in existing IQAN-LL installations.
An adapter cable allows drop-in replacement for service parts. The IQAN-LC5-C01
should be specified for all new machine production.
8
Instruction book, IQAN- LC5-C0x
8
3
Product description
MP handle
MP handle
The IQAN-LC5-C01 is designed to be used with the Multi-Purpose (MP) handle. The
MP handle together with a IQAN-LC5-C01 base will have one Deutsch DTM
connector for interfacing to connector C2 or C3 in the joystick base.
In order to reduce operator fatigue, the MP handle incorporates a hand rest, and is
designed for both left and right-handed use.
To extend operating life the housing is made of a corrosive-free material, and is
specially adapted for moisture drainage to protect the the system electronics. The MP
handle uses a bellow that can be quickly changed to simplify field replacement. The
cable between base and handle is routed directly through the base plate, eliminating the
risk of damage and simplifying field service, while the use of a single circuit board and
Hall effect sensors minimise the number of components and moving parts.
3
4
5
2
1
6
The MP handle parts.
The handle's parts
MP handle consists of:
1 Bellows, -MP handle.
2 Handle, -MPB2W2T1 shown, (other configurations are possible).
3 Momentary buttons.
4 Proportional thumbwheel (-MP handle thumbwheel has dual, mirrored outputs).
5 Momentary trigger button.
6 Cable and connector for -MP (6 pos. or 12 pos., depending on handle functions
connected to the base).
Instruction book, IQAN- LC5-C0x
9
9
I/O overview, MP handle
3
Product description
I/O overview, MP handle
POWER +5Vdc
B1
Bn
MP
GROUND
OUT-W1A
OUT-W1B
OUT-W2A
OUT-W2B
Buttons and thumbwheels
Digital
The MP handle has up to nine (9) buttons that are connected as digital inputs on the
IQAN-LC5-C01 base.
(8) momentary buttons B1 thru B8
(1) momentary trigger button T1
Analogue
The MP handle has up to two (2) thumbwheels that are connected as analogue intputs
in the IQAN-LC5-C01 base. The thumbwheels have dual outputs that may be
connected to voltage inputs, but are best used for auxiliary DAC channels Z1-Z2.
(2) Primary analogue outputs OUT-W1A and OUT-W2A, 10%-90% Vs
(2) Secondary analogue outputs OUT-W1B and OUT-W2B, 90% - 10% Vs
Vdc
out
Ou
tp
ut
A
90% Vs
50% Vs
tp
Ou
B
ut
10% Vs
Deflection
-100%
Neutral
position
100%
MP handle outputs per thumbwheel used as dual analogue inputs.
Command
Ax
is
DA
C
+100%
0%
-100%
Deflection
100%
Neutral
position
100%
MP handle thumbwheel used as auxiliary DAC.
10
Instruction book, IQAN- LC5-C0x
10
Redundant signals
4
4
Safety
Safety
Redundant signals
In order to fulfill high safety demands, the joystick IQAN-LC5-C0x uses dual mirrored
sensors per axis. The sensor signals are compared in the controller; both have to show
matching activation for that axis to activate, and they have to match over the whole
joystick stroke. If a fault is detected the DAC channel will not be activated.
Internal diagnostics
The module performs a number of self-checks that improve safety. Checks include
monitoring of voltage supplies, checksums on memory and a watchdog that monitors
software execution. The module uses a real time operating system, which supervises
software execution.
If a critical error is detected, the module is stopped, with CAN bus and outputs off.
CAN-bus interruption
The IQAN-LC5-C0x communicates with an IQAN master module on the CAN bus.
Both the master and the IQAN-LC5-C0x check for any interruptions in the CAN-bus
communication. If an error occurs the master will use zero, or an application defined
error value for the joystick inputs, and its outputs will be off.
The error will be indicated both on the master module and with a blink code on the unit,
see Appendix B, on page 32.
Deadband
To prevent activation in the neutral position, the IQAN-LC5-C0x has a small built in
deadband, see section Joystick Deadband X, Y, on page 7. It may be necessary to set an
additional deadband in the application to increase the margin of safety.
Magnetic Fields
WARNING
Risk of injury! Do not use in areas with high magnetic fields.
The IQAN-LC5 is based on hall effect sensors. Exposure to high external magnetic
fields may lead to unwanted activation of the output signals.
For maximum allowed external magnetic field, see Appendix A, on page 28.
11
Instruction book, IQAN- LC5-C0x
11
Mounting the unit
5
5
Mounting
Mounting
Mounting the unit
N OTICE
The IQAN-LC5-C0x unit should be mounted according to the following instructions.
Mounting considerations
• The control lever must be built in so that it is protected against direct pressurized
liquid spray (above flange) and excessive mechanical forces.
• The machine manufacturer must consider the need of a protective catch, or similar,
to prevent unintentional working of the lever.
N OTICE
Take careful consideration when positioning the unit.
• Mount the unit so that it is not exposed to external heat, e.g. from the engine or
heater.
• Mount the unit so there is no risk that the harness can be folded, crushed, worn or
damaged in any way.
• Locate the harness so there is no pressure on the connector.
• Use ergonomics. The control lever should be mounted at a height so that there is no
pressure on the driver's arm and shoulders. The IQAN-LC5-C0x and a well
designed handle, such as the MP, combined with moveable arm rests, can provide
good ergonomics. Always consider ergonomics when installing hand controls.
Mounting methods
• Control lever IQAN-LC5-C0x must only be mounted using screws through the
flange.
4x
Mounting the IQAN-LC5-C01 with screws.
12
Instruction book, IQAN- LC5-C0x
12
Handle considerations
5
Mounting
• Allow sufficient space beneath the unit to provide for unplugging the connectors.
75
Required space for connectors.
For mounting dimensions, see Appendix C, on page 34.
Handle considerations
Recommended handle specification
In addition to the MP handle, the IQAN-LC5-C01 will accept OEM specified handles.
These handles will need to be adapted to mount on the joystick stem. The maximum
weight of any handle fitted to the IQAN-LC5-C01 combined with its center of gravity
(COG), shall not cause more force than the minimum activation moment. For the
minimum activation force, see Appendix A, on page 28. Any tilting of the lever by
armrest movement or possible machine leveling or orientation should be taken into
consideration when specifying a suitable handle.
WARNING
Risk of injury! Exceeding the recommended handle specifications could cause
unintended movement of the joystick.
Environmental specification
Any handle used with the IQAN-LC5-C01 should be a sealed type that is rated IP65 for
outdoor use. Additionally, the joystick must always have a bellow installed to ensure
that it will meet the environmental specification for sealing above the flange. When
using a handle from a different manufacturer than Parker, be sure to include a suitable
bellow made of a material that is able to withstand the stresses of outdoor use in mobile
hydraulic machinery.
N OTICE
Failure to use a properly fitted bellow of the correct material will cause the unit to not
meet its environmental specification and may result in damage to the IQAN-LC5-C01
joystick.
13
Instruction book, IQAN- LC5-C0x
13
IQAN-LC5-C0x connectors
6
6
Installation
Installation
IQAN-LC5-C0x connectors
Deutsch no. WM6S
Sealing plug
Deutsch no. 0413-204-2005
Housing, C2
Deutsch no. DTM06-12SA
Pin type
Deutsch no. 1062-20-0222
Lock type
Deutsch no. WM12S
Sealing plug
Deutsch no. 0413-204-2005
Recommended
cable
0.75-1 mm2 (18 AWG)
C2
1
12
Wedge type
3
Deutsch no. 1062-20-0222
4
Pin type
C1/C3
2
Deutsch no. DTM06-6S
5
Housing,C1/C3
6
Parker 5035007
1
Connector kit
2
11
3
10
4
9
5
8
6
7
+BAT
ADDR-H
-BAT
ADDR-L
+VREF
-VREF
+VREF
-VREF
LC5
-C01
CAN-H
CAN-L
1x DOUT
8x VIN
5x DIN
Connector C1 pin assignments (-C01 & -C02)
Symbol
Pin No.
Function
+BAT
6
Power supply
-BAT
1
Power supply
CAN-L
2
CAN low voltage bus line.
CAN-H
5
CAN high voltage bus line.
ADDR-L
3
Address
ADDR-H
4
Address
14
Instruction book, IQAN- LC5-C0x
14
Connector C2 pin assignments (-C01)
6
Installation
Connector C2 pin assignments (-C01)
Symbol
Pin No.
Function
+VREF-A
12
Voltage reference for external sensors. Sourcing +5V.
-VREF-A
1
Voltage reference for external sensors. Return (0V).
VIN-A
DIN-F
DAC-Z1P
2
Input from -MP handle or external device
VIN-B
DIN-G
DAC-Z1S
3
Input from -MP handle or external device
VIN-C
DIN-H
DAC-Z2P
10
Input from -MP handle or external device
VIN-D
DIN-I
DAC-Z2S
11
Input from -MP handle or external device
DIN-A
4
Input from -MP handle or external device
DIN-B
5
Input from -MP handle or external device
DIN-C
6
Input from -MP handle or external device
DIN-D
8
Input from -MP handle or external device
DIN-E
9
Input from -MP handle or external device
DOUT-A
7
Output
Connector C3 pin assignments (-C01)
Symbol
Pin No.
Function
+VREF-B
6
Voltage reference for external sensors. Sourcing +5V.
-VREF-B
1
Voltage reference for external sensors. Return (0V).
VIN-E
DIN-J
DAC-Z3P
2
Input from -MP handle or external device
VIN-F
DIN-K
DAC-Z3S
3
Input from -MP handle or external device
VIN-G
DIN-L
4
Input from -MP handle or external device
VIN-H
DIN-M
5
Input from -MP handle or external device
15
Instruction book, IQAN- LC5-C0x
15
Connector C2 pin assignments (-C02)
6
Installation
Connector C2 pin assignments (-C02)
Symbol
Symbol
IQANdevelop
Pin
No.
Function
IQANdesign
+VREF-A
+VREF-A
12
Voltage reference for external sensors. Sourcing +5V.
-VREF-A
-VREF-A
1
Voltage reference for external sensors. Return (0V).
VIN-A
DIN-G
VIN-A
2
Input from external device
VIN-B
DIN-H
VIN-B
3
Input from external device
DIN-A
DIN-A
4
Input from external device
DIN-B
DIN-B
5
Input from external device
DIN-C
DIN-C
6
Input from external device
DIN-D
DIN-D
8
Input from external device
DIN-E
DIN-E
9
Input from external device
DIN-F
DIN-F
10
Input from external device
DOUT-A
DOUT-A
7
Output
Not used
Not used
11
No connection
Connector C3 pin assignments (-C02)
Symbol
Symbol
IQANdevelop
Pin
No.
Function
IQANdesign
+VREF-B
+VREF-B
6
Voltage reference for external sensors. Sourcing +5V.
-VREF-B
-VREF-B
1
Voltage reference for external sensors. Return (0V).
DIN-I
DIN-G
2
Input from handle
DIN-J
DIN-H
3
Input from handle
DIN-K
DIN-I
4
Input from handle
DIN-L
DIN-J
5
Input from handle
16
Instruction book, IQAN- LC5-C0x
16
MP handle connector, 6 position for C3 connection
6
Installation
MP handle connector, 6 position for C3 connection
Wedge type
Deutsch no. WM6S
Sealing plug
Deutsch no. 0413-204-2005
Supplied on
handle types
MPB0W0T1, MPB2W0T0,
MPB2W0T1, MPB4W0T0
+Vref
3
Deutsch no. 1062-20-0222
4
Pin type
C3
2
Deutsch no. DTM06-6S
5
Housing
6
Parker 20072408
1
Connector parts
B1
Bn
MP
Connector, 6 position assignments
MPB0W0T1
MPB2W0T0
MPB2W0T1
MPB4W0T0
Symbol
Pin No.
Pin No.
Pin No.
Pin No.
+Vref-B
6
6
6
6
B1
2
2
2
B2
3
3
3
B3
4
B4
5
T1
4
4
17
Instruction book, IQAN- LC5-C0x
17
MP handle connector, 12 position for C2 connection
6
Installation
MP handle connector, 12 position for C2 connection
Housing
Deutsch no. DTM06-12SA
Pin type
Deutsch no. 1062-20-0222
Wedge type
Deutsch no. WM12S
Sealing plug
Deutsch no. 0413-204-2005
Supplied on
handle types
MPB4W0T1, MPB8W0T0,
MPB8W0T1, MPB2W2T0,
MPB2W2T1, MPB4W1T0,
MPB4W1T1
C2
2
11
Parker 20072406
1
12
Connector parts
3
10
4
9
5
8
6
7
+Vref
B1
Bn
MP
Connector, 12 position assignments
MPB4W0T1
MPB8W0T0
MPB8W0T1
Symbol
Pin No.
Pin No.
Pin No.
+Vref-A
12
12
12
B1
4
4
4
B2
5
5
5
B3
6
6
6
B4
8
8
8
B5
2
2
B6
3
3
B7
10
10
B8
11
11
T1
9
9
Types with thumbwheels continued in separate table.
18
Instruction book, IQAN- LC5-C0x
18
MP handle connector, 12 position for C2 connection
6
+Vref
Installation
B1
Bn
MP
DAC-Z1P
DAC-Z1S
DAC-Z2P
-Vref
DAC-Z2S
Connector, 12 position assignments
MPB2W2T0
MPB2W2T1
MPB4W1T0
MPB4W1T1
Symbol
Pin No.
Pin No.
Pin No.
Pin No.
+Vref-A
12
12
12
12
-Vref-A
1
1
1
1
B1
4
4
4
4
B2
5
5
5
5
B3
6
6
B4
8
8
T1
9
9
DAC-Z1S
3
3
3
3
DAC-Z1P
2
2
2
2
DAC-Z2P
10
10
DAC-Z2S
11
11
19
Instruction book, IQAN- LC5-C0x
19
MP handle connector, 12 position for C2 connection
6
Installation
Required connectors, based on model code
Model code
5035007 kit with
housings for
C1/C2/C3
IQAN-LC5-C01-U1
1 pc
IQAN-LC5-C01-U2
1 pc
IQAN-LC5-C01-H1
1 pc
IQAN-LC5-C01-MPB0W0T0
1 pc
20072408 kit with
6 pin housing
for C1
20072406 kit with
12 pin housing
for C2
C3 connector from MP handle cable is factory mounted in joystick base
IQAN-LC5-C01-MPB0W0T1
1 pc
1 pc
IQAN-LC5-C01-MPB2W0T0
1 pc
1 pc
IQAN-LC5-C01-MPB2W0T1
1 pc
1 pc
IQAN-LC5-C01-MPB4W0T0
1 pc
1 pc
C2 connector from MP handle cable is factory mounted in joystick base
IQAN-LC5-C01-MPB4W0T1
2 pcs
IQAN-LC5-C01-MPB8W0T0
2 pcs
IQAN-LC5-C01-MPB8W0T1
2 pcs
IQAN-LC5-C01-MPB4W1T0
2 pcs
IQAN-LC5-C01-MPB4W1T1
2 pcs
IQAN-LC5-C01-MPB2W2T0
2 pcs
IQAN-LC5-C01-MPB2W2T1
2 pcs
MP handle faceplate function numbering
4
1
1
3
6
2
7
2
2
3
4
1
B2W0T0
B2W0T1
B4W0T0
B4W0T1
3
2
1
1
8
B8W0T0
B8W0T1
2
1
5
2
B2W2T0
B2W2T1
4
1
B4W1T0
B4W1T1
B0W0T0
B0W0T1
MP button and thumbwheel numbering.
20
Instruction book, IQAN- LC5-C0x
20
IQAN-LC5-C01 supply voltage
6
Installation
IQAN-LC5-C01 supply voltage
WARNING
Before any installation of the IQAN system can take place, make sure the ignition lock
is turned off and the battery is disconnected.
Emergency stop
Make sure an Emergency Stop disconnecting the power supply, is easily accessible at
any time. The figure below shows how to connect the emergency stop.
Connecting of supply voltage, -C0x
The supply voltage, should be within the operating range, see Appendix A, on page 28.
Connect the supply voltage to +BAT pin C1:6. The ground connection is made from
-BAT pin C1:1 to the negative terminal of the battery..
EXAMPLE
E-stop
IQAN-LC5-C01
3A
*
+BAT
-BAT
+
-
* Symbol for disconnecting
switch for battery, ignition
lock and other fuses.
Connecting an IQAN-LC5-C0x to power supply.
N OTICE
Do not use the chassis as the negative terminal.
Polarity reversal
The IQAN-LC5-C0x module is protected against power supply polarity reversal. An
external fuse, max 3A (Fast) must be used. Polarity reversal can damage the unit if the
fuse is not used.
21
Instruction book, IQAN- LC5-C0x
21
IQAN-LC5-C0x addressing/terminating
6
Installation
IQAN-LC5-C0x addressing/terminating
Addressing
Each IQAN-LC5-C0x module will have a specific address, enabling the master module
to communicate with the modules through the CAN-bus. When operating, the system
distinguishes between different modules by first verifying the module type and
secondly, through the modules having unique addresses.
EXAMPLE
If having an IQAN-LC5-C01 module with address 0, the system will denote this one
as LC5-A0, The letter "A" in the example refers to CAN-bus A.
The maximum number of similar modules in a system is four or eight depending on the
master module, denoted in the first case as addresses 0, 1, 2, 3 respectively. In order to
assign any IQAN-LC5-C0x module a unique CAN-address, an ID-Tag will have to be
connected to the positions ADDR-H and ADDR-L.
IQAN-LC5-C0x
ADDR-L
ID-Tag
ADDR-H
Connecting of Id-Tag in IQAN-LC5-C0x connector C1.
Terminating
To eliminate interference in the communication, through the CAN-bus, the CAN-bus
must be terminated. If an IQAN-LC5-C0x is located at the end of the CAN-bus then
use an ID-tag having a combined address and terminating function. This is denoted
with a "T" for terminating, after the appropriate address such as; 0T, 1T, 2T...
Selecting appropriate Id-Tag
• Check the address number of the module.
• If the module is located at the end of the CAN-bus then select the appropriate IDTag denoted with a "T".
N OTICE
The CAN-bus does not need to be terminated using an external 120 ohm terminating
resistor, due to the fact that terminating can be made inside the IQAN-LC5-C0x module in conjunction with an installed ID-Tag with terminating function.
22
Instruction book, IQAN- LC5-C0x
22
Reference voltage, VREF
6
Installation
Reference voltage, VREF
The IQAN-LC5-C0x module is internally equipped with a voltage regulator to generate
the reference voltage VREF. The standard reference voltage will feed different kinds of
sensors, potentiometers and joysticks.
IQAN-LC5-C01
+VREF-A
-VREF-A
+VREF-B
-VREF-B
VREF positions in connectors C2 and C3.
N OTICE
Maximum load for the VREF, see Appendix A, on page 28.
Do not use the -VREF as ground for any devices that are not powered from +VREF.
You could damage the unit.
23
Instruction book, IQAN- LC5-C0x
23
Connecting sensors and switches to IQAN-LC5-C01
6
Installation
Connecting sensors and switches to IQAN-LC5-C01
Connecting sensors to the voltage inputs
The sensor signal range must be 0-5 Vdc. To detect signal errors such as short circuits
or interruptions the active signal range is recommended to be within 0.5-4.5 Vdc.
[V]
5
Error detection range
Active signal range
0
Error detection range
t
Active signal range.
The current consumption related to the voltage input is negligible.
The following describes the connection of any analog sensor. This includes
temperature, pressure, angle and position sensors. The positive terminal of the sensor is
connected to the +VREF position and the corresponding negative terminal to the VREF position. The sensor signal is connected to appropriate VIN position. For a
resistive type element, select the potentiometer value for the sensor to achieve the best
linearity.
EXAMPLE
Connect the positive and negative terminals of the position sensor to +VREF,
position C2:12, and -VREF, position C2:1, respectively. Then connect the sensor
signal to VIN-A, position C2:2.
IQAN-LC5-C01
+VREF
VIN
-VREF
Position Sensor
Connecting VREF and sensor signal VIN.
N OTICE
The negative terminal of the sensor must not be connected to the chassis.
Maximum load for VREF position, see Appendix A, on page 28.
24
Instruction book, IQAN- LC5-C0x
24
Connecting sensors and switches to IQAN-LC5-C01
6
Installation
Connecting switches to the inputs
Switches could be connected to the inputs, to create a digital on/off signal. The
switches may be connected to +VREF and DIN respectively for 5Vdc signal. The
current consumption for the input is negligible.
EXAMPLE
Connect the positive and negative terminals of the switch to +VREF, position C2:6,
and DIN-A, position C2:4, respectively.
IQAN-LC5-C01
+VREF
DIN
Switch
Connecting a switch to DIN and VREF.
N OTICE
Maximum load for VREF position, see Appendix A, on page 28.
It is possible to connect system voltage +BAT to the input through a switch in order to
reserve 5Vdc VREF for sensors and potentiometers.
EXAMPLE
Connect the positive and negative terminals of the switch to +BAT supply and DINA, position C2:4, respectively.
+BAT
IQAN-LC5-C01
DIN
Switch
Connecting a switch to DIN and +BAT.
25
Instruction book, IQAN- LC5-C0x
25
Start-up procedures
7
7
Start-up
Start-up
Start-up procedures
This chapter contains instructions for action to be taken in connection with the initial
start.
WARNING
Risk of injury!
If the control system is not fitted properly, the machine could move uncontrollably. The
machine’s engine shall not be started before the control system is completely fitted and
its signals are verified.
Starting the control system
Start the control system as follows:
• Prior to start, all modules and cables are to be fitted correctly.
• Check fuses, i.e. make sure that the supply voltage to the modules is equipped with
the correct fuse.
• Make sure that connections for supply voltage and return lines are correct in the
cable’s conductor joint.
• Make sure an emergency stop is installed.
The emergency stop should disconnect the supply voltage to all modules.
Alternatively, the emergency stop may also shut off the diesel engine or a dump
valve, and with that, depressurize the hydraulic system.
Prepare for system start
WARNING
Make sure no one is in dangerous proximity to the vehicle to avoid
injuries when it starts.
Prepare for the initial system start as follows:
•
•
•
•
The engine for the hydraulic system’s pump shall be in off position.
Make sure that all connectors are properly connected.
Turn on the control system.
Make sure that voltage is being supplied to all modules; the power/status diode shall
be illuminated on all modules. Also, make sure that the master is in contact with all
modules by reading the master’s display.
• Make sure the emergency stop is functioning properly.
Start the system
Start the system as follows:
• Start the engine for the hydraulic system’s pump, assuming that the above
mentioned inspections have been carried out and shown correct values.
• Calibrate and adjust input and output signals according to the instructions related to
the master menu system and check each and every output function carefully.
26
Instruction book, IQAN- LC5-C0x
26
Start-up procedures
8
8
System Diagnostics
System Diagnostics
The yellow blinking LED on the module indicates normal status. If there is an error
detected, the master will present a message on the display. The IQAN-LC5-C0x
module also indicates error status through the red blinking LED as shown below.
This gives an immediate diagnosis as to the nature of the error that has occurred.
Yellow/ red, status LED
The location of the LED indicators on the IQAN-LC5-C0x module.
The yellow/red LED will be blinking yellow once per every two seconds (0.5 hz) to
indicate power and normal operating status. The LED will blink red when an error has
been detected. To get futher information about the error messages, see Appendix B, on
page 32.
A SMALL RECOMMENDATION ...
You can use the internal diagnostics in the master to get more information about the
IQAN-LC5-C0x module.
The following values are supervised:.
Internal temperature [°C]
Reference voltage [V]
CAN address voltage [V]
Note: In the IQAN-LL, the power supply (+BAT) was also monitored. For
compatibility, in the IQAN-LC5-C02, the power supply is a constant, faked value.
27
Instruction book, IQAN- LC5-C0x
27
IQAN-LC5-C0x Technical Overview
Appendix A
Appendix A
IQAN-LC5-C0x Technical Overview
IQAN-LC5-C01, base and -MP handle
Absolute Maximum Ratingsa
Parameter
Remark
Ambient temperature, TA
-40 to 85 °C
Storage temperature
-40 to 100 °C
Maximum voltage supply on +BAT
6 to 36 V, no system reset, power drivers will saturate at low voltage
Voltage on any pin with respect to -BAT
36 V
External magnetic fields
2.5 mT
a.The “Absolute Maximum Ratings” table lists the maximum limits to which the device can be subjected without damage. This doesn´t
imply that the device will function at these extreme conditions, only that, when these conditions are removed and the device operated
within the “Recommended Operating Conditions”, it will still be functional and its useful life won’t have been shortened.
Environmental ratings
Parameter
EMC
Radiated emission
Conducted emission
Conducted susceptability
Radiated susceptability
Conducted transients susceptability
Remark
ISO 13766:2006/ISO 14982:1998
EN 55025:2003, 0.15-108 MHz Class 2
ISO 11452-4:2005, 1 - 200 MHz, 1 kHz, 80% AM, 100 mA
ISO 11452-2:2004, 200-2000 MHz, 1kHz, 80% AM, 100 V/m
ISO 7637-2:2004, Pulse 1, 2a, 2b, 3a, 3b, 4, 5, Level 3
ISO 7637-3:2007, Level 3
ESD
Operation
Handling
ISO 10605:2008, 8 kV contact, 25 kV air
ISO 10605:2008, 4 kV contact
Mechanical environment
Random vibration
Shock
IEC 60068-2-64:2008 Fh, 15 - 1000 Hz, 11.6 Grms, 3 x 10 hours
IEC 60068-2-27:2008 Ea, 40 g, 6 ms, 1000 * 6 directions
Climate environment
Enclosure, water and dust protection
Salt mist
Damp heat, cyclic
Damp heat, steady state
Heat, operation
Heat, storage
Cold
Change of temperature
IEC 600529:2001, IP65 (with sealed handle and bellow)
IEC 68-2-52:1996 Kb, 72 hours (not tested)
IEC 60068-2-30:2005 Db, +55°C, 95% RH, 6 cycles
IEC 60068-2-78:2001 Cab, +40°C, 93% RH, 21 days
IEC 60068-2-2:2007 Bb, 85°C, 72 hours
IEC 60068-2-2:2007 Bb, 100°C, 72 hours
IEC 60068-2-1:1993 Ab, -40°C, 16 hours
IEC 60068-2-14:1984 Nb, -30°C to +85°C, 100x4 hours
System
TA = +25 °C (unless otherwise specified)
Parameter
Remark
Weight
Base
Base with -MP handle
380 g
750 g
Ambient temperature
-40 to 85 °C
28
Instruction book, IQAN-LC5-C0x
28
IQAN-LC5-C0x Technical Overview
Appendix A
System
TA = +25 °C (unless otherwise specified)
Parameter
Remark
Voltage supply, VBAT
9 to 32 V
Current supply
VBAT =14 V
VBAT = 28 V
typ. 45 mA
typ. 30 mA
CAN
CAN specification
CAN 2.0A, CAN 2.0B
CAN speed
125 to 500 kbits
Protection
SCB, SCG
VREF sensor supply
Parameter
Remark
Output voltage
5 V ±150 mV, -40 to 85 °C
Output voltage temperature drift
0.25 mV/°C, -40 to 85 °C
Maximum load current
50 mA for each VREF
Protection
overload, SCB, SCG
Diagnostics
under/over voltage, overload
Under/over voltage threshold
±150 mV from nominal value
I/O
TA = +25 °C (unless otherwise specified)
Parameter
Remark
Base, DAC (X-Y coordinates)
Angle of movement
±18°
Center position output
0%
Minimum position output
-100%
Maximum position output
100%
Neutral zone
10% of full deflection
Deflection moment, neutral
0.6 Nm
Deflection moment, fully activated
1.4 Nm
One time loading
100 Nm
Expected life
5 x 106 cycles (One cycle: Center pos. to full +direction and back,
center pos. to full -direction and back)
Diagnostics
diff. check on dual antivalent signals
Base, VIN (Voltage input)
Full scale
5000 mV ±100 mV
Resolution
10 bits (4.88 mV)
Input impedance
36 Kohm in parallel with 10 nF
29
Instruction book, IQAN-LC5-C0x
29
IQAN-LC5-C0x Technical Overview
Appendix A
I/O
TA = +25 °C (unless otherwise specified)
Parameter
Remark
Accuracy
with external sensor supply
with VREF sensor supply
±(0.8 % + 5 mV), -40 to 70 °C
±(0.2 % + 5 mV), -40 to 70 °C
Maximum continuous voltage
32 V
Protection
SCB, SCG
Diagnostics
defined in application
Base, DIN (on/off input)
Input signal low
<1 V
Input signal high
>4 V
Input hysteresis
>0.55 V
Input impedance
6.2 kohm in parallel with 10 nF
Maximum continuous voltage
32 V
Diagnostics
defined in application
Base, DOUT (on/off output)
Load current
200 mA
Power driver voltage drop
<0.70 V
Leakage current in off-state
<100 uA
Protection
overload, SCB, SCG
Diagnostics
none
IQAN-LC5-C01, -MP handle only
Thumbwheel
I/O
TA = +25 °C, unless otherwise specified
Parameter
Remark
Handle, DAC (Z coordinates)
Angle of movement
±25°
Center position output
0%
Minimum position output
-100%
Maximum position output
100%
Neutral zone
10% of full deflection
Current supply
max. 23 mA, typ. 16 mA (per thumbwheel)
Deflection moment, neutral
10 Nmm
Deflection moment, fully activated
15 Nmm
Expected life
5 x 106 cycles (One cycle: Center pos. to full +direction and back,
center pos. to full -direction and back)
Diagnostics
diff. check on dual antivalent signals
30
Instruction book, IQAN-LC5-C0x
30
IQAN-LC5-C0x Technical Overview
Appendix A
Buttons
Parameter
Remark
Expected life
1.5x106 (tested 1.5x106 cycles)
Total travel
1.5 mm
Switching point
1.2 mm
Operating force
2 to 5 N
Max current
400 mA @ 32 VAC, resistive load (from mfg’s documentation)
Max current
100 mA @ 50 VDC, resistive load (from mfg’s documentation)
31
Instruction book, IQAN-LC5-C0x
31
Error codes, messages and actions
Appendix B
Appendix B
Error codes, messages and actions
If one of the following errors are detected, a message will be presented on the master
display together with an error code on the module. In some cases, the module will turn
off, to increase safety.
WARNING
Do not use the machine if an error message or error code is activated.
The following sections will present the possible error codes and what measures to take
for different error situations put into appropriate context.
LED indicator showing different IQAN-LC5-C0x modes
Status
Blink (yellow light)
Normal (no errors)
Status
Blink (red light)
Safe state (red)
Error
code
Error
1:1
VREF error
3:1
CAN error
3:2
ADDR error
4:1
Internal error
Primary Blink (red)
Error category
Secondary Blink (yellow)
Error description
VREF ERROR
Situation
Error code
Action LC5-C01
Comment
VREF < 4,75 V
Error 1:1
-
Check voltage
VREF > 5,25 V
Error 1:1
-
Check voltage
32
Instruction book, IQAN-LC5-C0x
32
Error codes, messages and actions
Appendix B
MODULE IS OFFLINE
Situation
Error code
Action LC5-C01
Comment
CAN-bus off
Error 3:1
All outputs shuts
off.
Check CAN-bus
ADDR-H < 4,75 V
Error 3:2
-
Check voltage
ADDR-H
ADDR-H > 5,25 V
Error 3:2
-
Check voltage
ADDR-H
ADDR-L < 0,5 V
Error 3:2
During start up:
The module turns
off.
Check voltage
ADDR-L
ADDR-L > 4,5 V
Error 3:2
During start up:
The module turns
off.
Check voltage
ADDR-L
Internal error
Error 4:1
The module turns
off.
Contact supplier.
Situation
Error code
Action LC5-C01
Comment
Internal temperature
> max temp
Error 4:1
-
Check ambient
temperature
Situation
Error code
Action LC5-C01
Comment
X error, Y error
Error 4:1
Error value.
Contact supplier
HIGH TEMPERATURE
DAC ERROR
33
Instruction book, IQAN-LC5-C0x
33
Dimensioning of the IQAN-LC5-C0x
Appendix C
Appendix C
unit = mm
28
90
80
105
80
105
-G handle
158
Ø 6 (8x)
49
(Ø 108)
Alternative mounting holes
stem detail
10
12
M12 x 1.25
Dimensioning of the IQAN-LC5-C0x
34
Instruction book, IQAN-LC5-C0x
34
Dimensioning of the IQAN-LC5 with MP handle
Appendix C
Dimensioning of the IQAN-LC5 with MP handle
unit = mm
35
Instruction book, IQAN-LC5-C0x
35
For latest information visit our website www.iqan.com
Parker Hannifin
Electronic Controls Division
SE-435 35 Mölnlycke
Sweden
Tel +46 31 750 44 00
Fax +46 31 750 44 21
www.parker.com
Information in this instructionbook is subject to change without notice
Parker Hannifin
Electronic Controls Division
1651 North Main Street
Morton, IL 61550
USA
Tel +1 309 266 2200
Fax +1 309 266 6674
Publ no: HY33-8404-IB/UK
Edition: 2013-08-09