CP-300 (300x0.1g) - User Manual

American Weigh Scales, Inc.
CELLPHONE Scale
Digital Pocket Scale
T
CP-300 (300 x 0.1g)
CP-100 (100 x 0.01g)
User Manual
Cellphone Scale Manual
Thank you for purchasing the American Weigh
Cellphone Scale. Please read all operating instructions
carefully before use. This electronic scale is a
precision instrument. With normal care and proper
treatment, it will provide years of reliable service.
Never load the scale with more than the maximum
capacity. Overloading will permanently damage it!
Avoid any exposure to extreme heat or cold. Your
scale works better when operated at normal room
temperature. Always allow the scale to acclimate to
normal room temperature for at least one hour before
use. Give your scale sufficient warm up time. Usually
30-60 seconds before calibration to give the internal
components a chance to stabilize.
Keep your scale in a clean environment. Dust, dirt,
moisture, vibration, air currents and a close distance to
other electronic equipment can all cause an adverse
effect on the reliability and accuracy of your scale.
Handle with care. Gently apply all items to be weighed
onto the platform. Although this scale is designed to be
quite durable, try to avoid rough treatment as this may
permanently damage the internal sensor.
Avoid shaking, dropping or otherwise shocking the
scale. This is a precision instrument and must be
handled with extreme care.
Only operate the scale on a stable, vibration free
surface.
I. OPERATION
1. Press [ ] key.
2. Wait until "0.0” or "0.00" is displayed.
3. Place the item(s) to be weighed on the platform.
4. Using the [MODE] key, you can switch between
weighing units.
5. To turn the scale off, press the [ ] key again.
II. TARE WEIGHING
To weigh using the tray, you can place it on the
platform before turning the scale on or:
1. Turn on scale as described in the first section.
2. Place the weighing tray or container on the platform.
3. Press [ ] key briefly and wait until "0.0" is
displayed.
4. Add the "net-weight-item" to the tray or container.
III. CALIBRATION
Only calibrate your scale if your scale is not weighing
properly. This scale comes pre-calibrated.
A. CP-300 Calibration Steps
1. Turn off the scale. Press and hold the “MODE” key
then press the [ ] key until the display shows a
random number. Now release both keys.
2. Press the [ ] key again. The display will show “AL
0” then “300.0”. Gently place a 300g weight on the
center of the platform and press the [ ] key again.
The LCD will display “AL F” then “300.0”.
3. Calibration is complete. If the scale shows “AL E”,
an error has occurred - Turn off the scale and repeat
steps 1 through 3 above.
A. CP-300 Calibration Steps
1. Turn off the scale. Press and hold the “MODE” key
then press the [ ] key until the display shows a
random number. Now release both keys.
2. Press the [ ] key again. The display will show “AL
0” then “100.00”. Gently place a 100g weight on the
center of the platform. The LCD will display “AL F”
then “100.00”.
3. Calibration is complete. If the scale shows “AL E”,
an error has occurred - Turn off the scale and repeat
steps 1 through 3.
IV. CLOCK OPERATION
1. Diagram
A. Hour / 12/24 Time
B. Mode / Set / Enter
C. Minute / Start / Stop
D. Backlight
2. Clock Mode & Timer Mode
a. Press button B to switch between normal "Clock
Mode" and "Timer Mode".
3. Setting the Clock
a. While in normal "Clock Mode", press and hold the
B button.
b. The clock's hour and minute digits will flash.
c. Press button A to increment the hours by one. Hold
to go faster.
d. Press button C to increment the minutes by one.
Hold to go faster.
e. Press the B button when you are finished setting.
4. Setting the Timer
a. While in "Timer Mode" ( ), press and hold the B
button.
b. The timer's hour and minute digits will flash.
c. Press button A to increment the hours by one. Hold
to go faster.
d. Press button C to increment the minutes by one.
Hold to go faster.
e. Press the B button when you are finished setting.
5. Using the Timer
a. After setting the timer, press the C button to start the
countdown.
b. Press the C button again to stop it.
V. TROUBLESHOOTING
The primary reasons for inaccuracy or malfunction
are low batteries, incorrect calibration, overload or
operating under unstable conditions. Please keep this
in mind and maintain and operate your scale properly.
This scale is a precise instrument and must be
handled with the utmost care and caution.
[Display] Solution:
Nothing,
[EEEEE] [Oue2] ,
Change the batteries.
You are overloading the scale. Remove the excessive load immediately!
The delicate weighing load cell has been damaged by misusing the scale (i.e. it was shocked, dropped or overloaded). You can try recalibrating.
300g / 10.585oz / 9.645ozt /
193dwt
CP-300
0.01g / 0.001oz / 0.05ct /
0.1gn
100g / 3.528oz / 500ct /
1543gn
CP-100
Specifications
Capacity
0.1g / 0.005oz / 0.005ozt /
0.1dwt
Model
Resolution
100g (sold seperate)
2 x AAA Batteries (included)
10 Year Warranty
2.2 x 4.6 x 1 “
300g (sold seperate)
Calibration Weight
Scale Dimensions
(inches)
Warranty
Power