SCAN 1216 DMX

User Manual

Improvement and changes to specifications, design and this manual, may be made at any time without prior notice.

All rights reserved.

Contents

Features 1

General Instructions 2

1. Overview 3

1.1 Front View 3

1.2 Rear View 6

2. Operation Guide 7

2.1 Program Enable 7

2.2 Programming Scenes 8

2.2.1 Scene Editing 11

2.2.2 Scanner Copy 12

2.2.3 Scene Copy 13

2.2.4 Delete a Scene 15

2.2.5 Delete all Scenes 15

2.2.6 Bank Copy 16

2.3 Programming Chases 17

2.3.1 Program a bank of scenes into a Chase 18

2.3.2 Add a Step 18

2.3.3 Delete a Step 20

2.3.4 Delete a Chase 21

2.3.5 Delete all Chases 21

2.4 Assign/Reverse DMX channel 22

2.4.1 Assign DMX channel 22

2.4.2 Reverse DMX channel 24

2.4.3 Fade Time/Assign Fade Time 26

2.4.4 Delete a scanner of DMX channel 27

2.4.5 Clear all DMX channels 28

2.4.6 Display DMX channel 28

2.5 Set Up a new Logo 30

2.6 Running Scenes 32

2.6.1 Manual Mode 32

2.6.2 Auto Mode 32

2.6.3 Music Mode 34

2.7 Running Chases 35

2.7.1 Manual Mode 35

2.7.2 Auto Mode 35

2.7.3 Music Mode 36

2.8 MIDI Operation 37

2.8.1 MIDI Channel Setting 37

2.8.2 Implementation 38

2.9 Send File Dump 39

2.10 Receive File Dump 40

Technical Specifications 41

1

Features

Thank you for your purchase This product features include:

192 DMX channels

12 scanners of 16 DMX channels

30 banks of 8 programmable scenes

6 chases of 240 programmed scenes from 30 banks

8 faders for manual control

All data can be sent or received between two or more units

Auto programs(scenes and chases) under control by Speed(or Tap Sync) and Fade Time sliders

Fade Time/Assign Fade Time

Reverse DMX channels causing the faders to control the output reversely

Preview assigned or reversed channel

8 CH./16 CH. mode for Assigned or Reversed DMX channels

The scanners under control by Pan and Tilt jog wheels

Fine adjustment of the Pan and Tilt

Blackout master

Manual override

Built-in microphone for Music triggering

MIDI control over banks, chases and Blackout

LCD display

DMX polarity select

Power failure memory

NOTE:

A knowledge of MIDI and DMX is required to fully utilize this unit.

General Instructions

Read the instruction in this manual carefully and thoroughly, as they give important information regarding safety during use and maintenance. Keep this manual with the unit, in order to consult it in the fut ure. If the unit is sold or given to a nother operator, make certain that it always has its manual, to enable the new owner to read about its operation and re lative instructions.

Warnings

DO NOT make any inflammable liquids, water or metal objects enter the unit.

Should any liquid be spilled on the unit, DISCONNECT the power supply to the unit immediately.

STOP using the unit immediately In the event of serious operation problems and

either contact your local dealer for a check or contact us directly.

DO NOT open the unit--there are no user serviceable parts inside.

NEVER try to repair the unit yourself. Repairs by unqualified people could cause

damage or faulty operation. Contact your nearest dealer.

Cautions

This unit is NOT intended for home use.

After having removed the packaging check that the unit is NOT damaged in any way.

If in doubt, DON'T use it and contact an authorized dealer.

Packaging material (plastic bags, polystyrene foam, nails, etc.) MUST NOT be left within children's reach, as it can be dangerous.

This unit must only be operated by adults. DO NOT allow children to tamper or play with it.

NEVER use the unit under the following conditions:

In places subject to excessive humidity.

In places subject to vibrations or bumps.

In p laces with a temperature of over 45 C /113 F or less than 2 C/3 5.6 F.

Protect the unit from excessive dryness or humidity (ideal conditions are between

35% and 80%).

DO NOT dismantle or modify the unit.

2

3

1. Overview

1.1 Front View

1. Overview

1.1 Front View

1. Scanner Buttons(1-12)

12 scanners of 16 DMX channels & fader control

Scanners

3

4

1

2

5

6

7

8

9

10

11

12

Scanners

7

8

5

6

9

10

3

4

1

2

11

12

DMX channels

1-16

17-32

33-48

49-64

65-80

81-96

97-112

113-128

129-144

145-160

161-176

177-192

DMX channels

1-16

17-32

33-48

49-64

65-80

81-96

97-112

113-128

129-144

145-160

161-176

177-192

Fader control

On

On

On

On

On

On

On

On

On

On

On

On

Fader control

Off

Off

Off

Off

Off

Off

Off

Off

Off

Off

Off

Off

LED

Off

Off

Off

Off

Off

Off

Off

Off

Off

Off

Off

Off

LED

On

On

On

On

On

On

On

On

On

On

On

On

Press a scanner button to turn on manual fader control. Press the scanner button again to turn off fader control. The LED besides the button lights or goes out to indicate this selection.

4

5

1. Overview

1.1 Front View

2. Scene Buttons

3. Faders

4. Page Select Button

5. Fog Machine Button

6. Speed Slider

7. Fade Time Slider

8. LCD Display

9. Pan Wheel

10. Tilt Wheel

11. Program Button

12. Music/Bank Copy

13. MIDI/Rec

14. Auto/Del

15. Bank Up/Down

16. Tap/Display

17. Blackout Button

18. Chase Buttons(1-6)

19. Fine Button

20. Mode Button

Press the scene buttons to load or stored your scenes.

There are a maximum of 240 programmable scenes.

These faders are used to control the intensity of channel 1-8 or channel 9-16 depending upon the selected page.

Used to select page between Page A(1-8) and Page B(9-16).

Activates Fog Machine .

Used to adjust the chase speed within the range of 0.1 second to 10 minutes.

Used to adjust the fade time. Fade time is the amount of time it takes for a fixture(or scanner) to move from one position to another, for the dimmer to fade in or fade out.

Shows the current activity or programming state.

This jog wheel is used to control the pan of the scanner or for programming.

This jog wheel is used to control the Tilt of the scanner or for programming.

Activates Program mode.

Activates Music mode or to copy a bank of scenes.

Used to control MIDI operation or to record programs.

Activates Auto mode or to delete scenes or chases.

Press the Up/Down button to select from 30 banks.

Used to create a standard beat or to change the value mode between % and 0-255.

Tap to momentarily pause whole output.

These buttons are used for activating the chase of programmed scenes.

When Fine is on, the Pan or Tilt wheel will control the scanner in the smallest increment.

Pressing Fine and Mode buttons allows to activate Assign or Reverse mode.

1. Overview

1.2 Rear View

AUDIO

0.1V~1Vp-p

MIDI IN

2

1=Ground

2=Data

3=Data +

1

DMX OUT

1=Ground

2=Data +

3=Data

3 DMX Polarity Select

2

DMX OUT

3

1 1

DMX IN

3

2

FOG

MACHINE

DC INPUT

+

DC 9V - 12V

300mA min.

POWER

ON OFF

1

2 3

4

5

6

7 8

1. AUDIO IN

2. MIDI IN

3. DMX Polarity Select

4. DMX Out

0.1V~1Vp-p.

Receives MIDI data.

Used to select DMX polarity.

This connector sends your DMX value to the DMX scanner or DMX pack.

5. DMX In

This connector accepts your DMX input signals.

6. Fog Machine Connector

7. DC Input

This connector is used to plug in the Fog Machine.

DC 9 -12V, 300mA min.

+

8. Power Switch

This switch turns On/Off the power.

6

2. Operation Guide

7

General

This unit allows you to program 12 scanners of 16 DMX channels, 30 banks of 8 programmable scenes, 6 chases of 240 programmed scenes using 8 faders and other function buttons. With the use of two jog wheels, you may easily control the

Pan or Tilt of the scanners. To tailor your special effect lighting, this unit enables you to Assign or Reverse the DMX channels. In addition, two or more units can communicate with each other so that they can send or receive file dump.

Display Information

The LCD Display contains a maximum of 2x8 characters.

LCD Display

CHASE 5

STEP 002

DATA 151

SP: 1M36S

TP: 5.32S

FT: 10.5S

ASS 07 08

RES 10 13

SN 6

BK 03

Message

Chase 5 is activated.

The 2nd step of a chase

DMX value(000-255)

The current speed is 1 minute and 36 seconds

The time of the last two taps is 5.32 seconds

Fade Time is 10.5 seconds

Assign DMX channels 7 and 8

Reverse DMX Channels 10 and 13

Scene 6

Bank 03

2.1 Program Enable

Program

When the power is turned on, this unit enters

Manual mode automatically.

Press the Program button for three seconds to activate Program mode, the LED near to this button lights indicating Program in active.

2. Operation Guide

2.2 Programming Scenes

Scanner buttons 1-12

1. Enter Program mode.

2. Press the Scanner button to turn on its fader

control, which is indicated by the lit LED.

You may select several scanners at a time

by tapping of these Scanner buttons, so you

can set several fixtures at a time.

11

3. Move the faders to select your desired dimmer

intensity if you are using a dimmer.

You can also use the two jog wheels to control

the Pan or Tilt movement of the scanner.

4. If necessary , you may tap the Page Select

button to control the second set of 8 DMX

channels.

5. Once the scene is satisfactory, tap the MIDI/Rec

button to program this scene into memory.

MIDI/Rec

8

2. Operation Guide

2.2 Programming Scenes

BANK

6. Tap the Bank Up/Down button to select the bank

you want to store your scene into. There are total

30 banks you can select, you may store up to 8

scenes into each bank.

SCENE BUTTONS 1-8

7. Tap the Scene button to store your scene, all

LEDs and the Segment Display will flash three

times briefly indicating this operation, then the

LCD will show the bank and the scene.

9

Scanner buttons 1-12

8. Repeat steps 3-7until all desired scenes

have been programmed into memory.

Tap the Scanner button again to turn off

its fader control.

To set another scanner(fixture), you may tap

the corresponding Scanner button to turn on

its fader control, then you may begin your

programming again.

2. Operation Guide

2.2 Programming Scenes

Program

9. If you don't intend to continue your programming,

press and hold down the Program button for three

seconds to exit Program mode, the LED goes out

indicating this selection.

EXAMPLE: Program 8 scenes with channel 1-8 at full in sequence into bank 2 and assign these scenes to scanner 2.

1. Program enable.

2. Tap the Scanner 2 button to turn on its fader control.

3. Tap the Page Select button to select Page A.

4. Push Fader 1 to the top position.

5. Tap the MIDI/Rec button.

6. Select bank 2 using Bank Up/Down button.

7. Tap the Scene 1 button to store the first scene.

8. Repeat steps 4-7 until all 8 scenes have been programmed into bank 2.

9. Tap the Scanner 2 button again to turn off its fader control.

10. Press the Program button for 3 seconds to exit Programming mode.

10

11

2. Operation Guide

2.2.1 Scene Editing

1. Program enable.

2. Tap the Bank Up/Down button to select the bank

that contains the scene you wish to edit.

BANK

SCENE

3. Select the scene you want to edit by tapping

its Scene button.

11

4. Use the Faders or jog wheels to make your

desired adjustments.

2. Operation Guide

2.2.1 Scene Editing

MIDI/Rec

5. Once you've made your changes, tap the

MIDI/Rec button.

SCENE

6. Tap the Scene button that corresponds to the

scene you're editing. This will overwrite the

exited scene.

NOTE:

Be sure to select the same scene in steps 3 and 6, otherwise you may accidentally record over an exited scene.

2.2.2 Scanner Copy

SCANNER

This function allows you to copy the settings of one scanner to another.

1. Press and hold down the Scanner button you

want to copy.

12

13

2. Operation Guide

2.2.2 Scanner Copy

SCANNER

2. While holding the Scanner button, tap the

Scanner button you want to copy to.

2.2.3 Scene Copy

1. Program enable.

2. Tap the Bank Up/Down button to select the bank

that contains the scene you wish to copy.

BANK

SCENE

3. Select the scene you want to copy by tapping

its Scene button.

2. Operation Guide

2.2.3 Scene Copy

4. Tap the Bank Up/Down button to select the bank

you wish to copy the scene to.

BANK

5. Tap the MIDI/Rec button.

MIDI/Rec

SCENE

6. Tap the Scene button you wish to copy the

scene to.

14

2. Operation Guide

2.2.4 Delete a Scene

SCENE

1. Tap the desired Scene button to select the scene

you wish to delete.

Auto/Del SCENE

2. Press and hold down the Auto/Del button.

While holding down the Auto/Del button, tap

the Scene button that stores the scene you

wish to delete.

When a programmed scene is deleted, all DMX

channel in this scene is set to 0.

15

2.2.5 Delete all Scenes

This function will reset all DMX channel to 0 output.

Program

BANK

1. With the power off, press and hold down the

Program and Bank Down buttons at a time.

2. Apply power again, all scenes should be cleared.

2. Operation Guide

2.2.6 Bank Copy

1. Program enable.

2. Tap the Bank Up/Down button to select the

bank you wish to copy.

BANK

3. Tap the MIDI/Rec button.

MIDI/Rec

BANK

4. Tap the Bank Up/Down button to select the

bank you wish to copy to.

16

2. Operation Guide

2.2.6 Bank Copy

Music/Bank Copy

5. Tap the Music/Bank Copy button, all LEDs

will flash three times briefly indicating the

function has been completed.

6. Press the Program button for three seconds to

exit Programming mode.

17

2.3 Programming Chase

You must program scenes before you can program chases, this function allows you to store up to 240 scenes into one chase.

1. Program enable.

Chase Button 1-6

2. Tap the Chase button to select the chase to

program. Each time you can select a chase

only.

3. Select a desired scene from the bank that has stored scenes.(described in Programming Scenes)

MIDI/Rec

4. Tap the MIDI/Rec button.

5. Repeat steps 3-4 until you've reached your

desired effect.

You may record up to 240 scenes into a chase.

2. Operation Guide

2.3.1 Program a bank of scenes into a Chase

Music/Bank Copy

1. Program enable.

2. Select the chase using Chase buttons 1-6.

3. Use Bank Up/Down button to select the bank

that contains the scenes you wish to copy.

4. Tap the Music/Bank Copy button.

MIDI/Rec Copy

5. Tap the MIDI/Rec Copy button, all LEDs will

flash three times briefly indicating all 8

scenes in this bank have been programmed

into this chase.

2.3.2 Add a Step

Tap/Display

1. Program enable.

2. Select the chase you wish to add a step to.

3. Tap the Tap/Display button, the LCD shows

the current step.

18

2. Operation Guide

2.3.2 Add a Step

4. Tap the Bank Up/Down button to scroll to the

step you wish to add a step after.

BANK

MIDI/Rec

5. Tap the MIDI/Rec button, the Segment Display

will read the step one higher than before.

For example, if you want to insert a step between

step 3 and step 4, and you scroll to step 3, when

you tap the MIDI/Rec button, the LCD will read

"STEP 004".

19

TAP/Display

6. Tap the Tap/Display button again, the LCD

shows the current chase, scene and bank.

Create a desired scene and record it as a new

step or select a programmed scene you wish to

add into this chase.

Hints:

You may tap the Tap Sync/Display button to change the

display mode between step and the bank.

2. Operation Guide

2.3.2 Add a Step

MIDI/Rec

7. Tap the MIDI/Rec button again , all LEDs will

flash three times briefly indicating the new

step has been inserted into this chase.

2.3.3 Delete a Step

Tap/Display

Auto/Del

1. Program enable.

2. Select the chase that contains the step you

wish to delete.

3. Tap the Tap/Display button, the LCD shows

the current step.

4. Tap the Bank Up/Down button to scroll to the

step you wish to delete.

5. Tap the Auto/Del button to delete the step, all

LEDs will flash three times briefly indicating

that the step has been deleted.

20

2. Operation Guide

2.3.4 Delete a Chase

1. Select the chase you wish to delete.

Chase Button 1-6

Auto/Del Chase

2. Press and hold down the Auto/Del button.

Tap the Chase button while holding down the

Auto/Del button, all LEDs will flash three times

briefly indicating this chase has been deleted.

21

2.3.5 Delete all Chases

Auto/Del

BANK

1. With the power off, press and hold down the Auto/Del

and Bank Down buttons at the same time.

2. Apply the power again.

2. Operation Guide

2.4 Assign/Reverse DMX channel

2.4.1 Assign DMX channel

1. Program enable.

FINE MODE

ASSIGN REVERSE

2. Press the Fine and Mode buttons at a time,

the Assign LED lights up indicating Assign mode

is active.

BANK

3. Use Bank Up/Down button to change between

the Pan and Tilt, the corresponding LED lights

indicating this selection.

TAP/Display

4. Tap the Tap/Display button to change between

8 CH. and 16 CH. mode, the LCD reads or

ASSXX XX

X/Y 08CH

ASSXX XX

X/Y 16CH

22

2. Operation Guide

2.4.1 Assign DMX channel

SCANNER

5. Tap the Scanner button to select the scanner.

23

6. Tap the Page Select button to select Page A or

Page B.

Page

Select

MODE SCENE BUTTONS 1-8

7. While pressing the Mode button, tap the Scene

button, all LEDs should flash briefly indicating

the DMX channel is assigned.( Scene button 1

stands for DMX channel 1, Scene button 2 stands

for DMX channel 2, and so on.)

8. Continue steps 3-7 , you may assign a maximum

of 48 DMX channels for 12 scanners.

2. Operation Guide

2.4.2 Reverse DMX channel

1. Program enable.

FINE MODE

ASSIGN REVERSE

2. Press the Fine and Mode buttons the second

time, the Reverse LED lights up indicating

Reverse mode is active.

BANK

3. Use Bank Up/Down button to change between

the Pan and Tilt, the corresponding LED lights

indicating this selection.

TAP/Display

4. Tap the Tap/Display button to change between

8 CH. and 16 CH. mode.

24

2. Operation Guide

2.4.2 Reverse DMX channel

SCANNER

5. Tap the Scanner button to select the scanner.

6. Tap the Page Select button to select Page A or

Page B.

Page

Select

25

MODE SCENE BUTTONS 1-8

7. While pressing the Mode button, tap the Scene

button, all LEDs should flash briefly indicating

the DMX channel is reversed.( Scene button 1

stands for DMX channel 1, Scene button 2 stands

for DMX channel 2, and so on.)

8. Continue steps 3-7 , you may reverse a maximum

of 48 DMX channels for 12 scanners.

2. Operation Guide

2.4.3 Fade Time/Assign Fade Time

1. With the power off, press the Mode and TAP/

Display buttons at a time.

MODE TAP/Display

TAP/Display

MODE TAP/Display

2. Apply the power again, tap the TAP/Display

button to change between Fade Time and

Assign Fade Time, the LCD reads

ALL CH

FD TIME or

ONLY X/Y

FD TIME

3. Press the Mode and TAP/Display buttons at a

time to store your setting into memory.

If you are not going to save your setting, tap

the Blackout button to leave this operation.

26

27

2. Operation Guide

2.4.4 Delete a scanner of DMX channels

1. Activate Assign or Reverse mode(Described in

the sub-chater 2.4.1 or 2.4.2).

SCANNER

2. Tap the Scanner button to select the scanner you

wish to delete.

MODE Auto/Del

3. Press the Mode and Auto/Del buttons at a time,

all LEDs should flash briefly, indicating the scanner

is deleted.

2. Operation Guide

2.4.5 Clear all DMX channels

1. Turn the power off.

MODE Auto/Del

2. Press the Mode and Auto/Del buttons

at a time

2.4.6 Display DMX channel

3. While pressing the two buttons, apply the

power again, all LEDs should flash briefly,

indicating all assigned or reversed DMX

channel are cleared

FINE MODE

1. Press the Fine and Mode buttons at a time,

the Assign LED lights.

28

29

2. Operation Guide

2.4.6 Display DMX channel

FINE MODE

2. Press the Fine and Mode buttons the second time,

the Assign LED goes out and the Reverse LED

lights.

SCANNER

3. Tap the Scanner button that holds the Pan and

Tilt channel, the LCD shows the Pan and Tilt.

2. Operation Guide

2.5 Set Up a new Logo

SCANNER 6 SCANNER 12

1. Turn the power off.

2. Press and hold down the Scanner 6 and Scanner

12 buttons at a time. Apply the power again while

pressing the two buttons, then release the two

buttons.

SCANNER

3. Tap the Scanner 6(or 12) button to move the

cursor to the left(or right).

BANK

4. Tap the Bank Up/Downbutton to scroll to the

characters you want.

5. Continue steps 3-4. You may enter a maximum

of 16 characters in two rows.

30

31

2. Operation Guide

2.5 Set Up a new Logo

SCANNER 6 SCANNER 12

6. Press the Scanner 6 and 12 buttons at a time

to store the new characters into memory, all

LEDs should flash briefly indicating this oper-

ation. If you are not going to save these new

characters, just tap the Blackout button to

leave this operation.

2. Operation Guide

2.6 Running Scenes

2.6.1 Manual Mode

1. When the power is turned on, this unit enters Manual mode automatically.

2. Make sure Auto and Music LEDs are both off.

3. Use the Bank Up/Down button to select the bank that contains the scenes you

wish to run.

4. Tap the Scene button to select the scene

to run.

SCENE

2.6.2 Auto Mode

This function allows you to run a bank of programmed scenes in a sequential loop.

Auto/Del

1. Tap the Auto/Del button to activate Auto mode.

The Auto LED lights indicating Auto mode is

active.

32

2. Operation Guide

2.6.2 Auto Mode

2. Use the Bank Up/Down button to select a bank

of scenes to run.

BANK

33

3. After selecting the bank of scenes you wish to

run, you can use the Speed slider(or Tap Sync/

Display button) and Fade Time slider to adjust

the scenes to your desired effect.

SPEED FADE TIME

Hints:

The Tap Sync button is used to set the speed by tapping the button several times, the last two taps will define the speed with a maximum of 10 minutes.

Tap Sync will override any previous setting of the Speed slider unless the slider is moved again.

Auto/Del

4. Tap the Auto/Del button again to exit Auto mode.

2. Operation Guide

2.6.3 Music Mode

Music/Bank Copy

1. Tap the Music/Bank Copy button to activate

Music mode. The Music LED lights indicating

Music mode is active.

BANK

2. Use the Bank Up/Down button to select the

bank that holds the scenes you wish to run.

The scenes you've selected will chase in a

sequential order according to the music

rhythms detected by the built-in microphone.

Music/Bank Copy

3. Tap the Music/Bank Copy button again to

exit Music mode.

34

2. Operation Guide

2.7 Running Chases

You must program scenes before you can run chases.

2.7.1 Manual Mode

1. When the power is turned on, this unit enters Manual mode automatically.

2. Select your desired chase by tapping one of the six Chase buttons. A second

tap of this button will deactivate this function.

3. Use the Fade Time slider to adjust the current scenes to your desired effects.

4. Use the Bank Up/Down button to run the chase

step by step.

BANK

35

2.7.2 Auto Mode

Auto/Del

1. Tap the Auto/Del button to activate Auto mode.

The Auto LED lights indicating Auto mode is

active.

2. Operation Guide

2.7.2 Auto Mode

Chase buttons 1-6

2. Select your desired chase by tapping one of

the six Chase buttons. A second tap of this

button will deactivate this function.

0.1SEC

30S

10MIN

SPEED FADE TIME

0

3. Use the Speed slider(or Tap Sync) and Fade

Time slider to adjust the chase to your desired

effects.

You may select several chases at a time, the

chases will run in sequence that you select the

chases.

2.7.3 Music Mode

Music/Bank Copy

1. Tap the Music/Bank Copy button to activate

Music mode, the Music LED lights indicating

Music mode is active.

36

37

2. Operation Guide

2.7.3 Music Mode

Chase buttons 1-6

2. Select your desired chase by tapping one of

the six Chase buttons, the chase will be

triggered by the music rhythms.

You may select several chases at a time.

2.8 MIDI Operation

2.8.1 MIDI Channel Setting

MIDI/Rec

1. Press and hold down the MIDI/Rec button for

three seconds, the LCD show the MIDI channel

of last time.

BANK

2. Use the Bank Up/Down button to select the DMX

channel 01-16 to assign to MIDI channel.

2. Operation Guide

2.8.1 MIDI Channel Setting

MIDI/Rec

3. Press and hold down the MIDI/Rec button for

three seconds to store your setting and to

deactivate MIDI setting.

To cancel your setting, tap any other button

(except Bank Up/Down buttons) to exit MIDI mode.

2.8.2 Implementation

This unit receives Note On signals, which enables to run 15 banks(01-15) of scenes and 6 chases of scenes. In addition, blackout function can be activated by MIDI signal.

BANK

Bank 1

Bank 2

Bank 3

...

Bank 14

Bank 15

Chase 1

Chase 2

Chase 3

Chase 4

Chase 5

Chase 6

NOTE NUMBER

00 to 07

08 to 15

16 to 23

...

104 to 111

112 to 119

120

121

122

123

124

125

126

FUNCTION

Turn on or off Scenes 1-8 of Bank 1

Turn on or off Scenes 1-8 of Bank 2

Turn on or off Scenes 1-8 of Bank 3

......

Turn on or off Scenes 1-8 of Bank 14

Turn on or off Scenes 1-8 of Bank 15

Turn on or off Chase 1

Turn on or off Chase 2

Turn on or off Chase 3

Turn on or off Chase 4

Turn on or off Chase 5

Turn on or off Chase 6

Blackout

38

39

2. Operation Guide

2.9 Send File Dump

NOTE

You must set up proper connection before you can send or receive the file dump.

SCANNER 2 SCANNER 3

1. With the power off, press and hold down the Scanner

buttons 2, 3 and Scene button 1 at a time.

SCENE BUTTON 1

2. Apply the power again while pressing these three

buttons, the LCD shows "TRANSMIT" indicating

this unit is ready to send the file dump.

SCENE BUTTON 7 & 8

3. Before you can send the file dump, please be sure

the second unit is in "RECEIVE" mode.

Press the Scene buttons 7 and 8 at a time to send

the file dump.

4. During the course of sending, if malfunction occurs,

the sending will be interrupted and the LCD shows

"ERROR".

2. Operation Guide

2.10 Receive File Dump

SCANNER 8 SCANNER 9

SCENE BUTTON 2

1. With the power off, press and hold down the

Scanner buttons 8, 9 and Scene button 2 at a time.

2. Apply the power again while pressing these three

buttons, the LCD shows "RECEIVE" indicating

this unit is receiving the file dump.

3. When receiving is over, this unit will return to

the normal mode.

40

41

Technical Specifications

Power Input ................................................ DC 9~12V, 300 mA min.

DMX Output .......................................................... 3 pin female XLR

MIDI Signal ................................................. 5 pin standard interface

Audio Input .................................................... By built-in microphone

Dimensions ............................................................. 482x132x73mm

Weight(appro.) ........................................................................ 2.5 kg

Equipson, S.A.

www.equipson.es

[email protected]