700TVL

SUPER WDR/3D DNR

STANDARD CAMERA

USER’S MANUAL

®

The Art of Surveillance

■ 1/3” 960H IT CCD

■ High Resolution 700TV Lines

■

■

■

■

■

■

WDR(Wide Dynamic Range)

3D DNR(Digital Noise Reduction)

Sens-Up Function(x512)

Eclipse Function

Zero Defect

Day & Night (ICR-Optional)

Motion Detection ■

■ Back Light Compensation

■

■

■

RS485 / PELCO-D

Privacy Mask(Polygonal,8 Colors)

O.S.D menu function

960H/SP 001

The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

INFORMATION This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARNING Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

CAUTION : To prevent electric shock and risk of fire hazards:

Do NOT use power sources other than that specified.

Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and should conform to all local codes.

Precaution

Do not Keep the camera face to strong light directly

Do not install the camera in extreme temperature conditions.

Do not disassemble the camera even if troubles happened

To avoid malfunctions, never use the camera close to a gas or oil leak

Do not drop the camera or subject them to physical shocks.

Do not expose the camera to rain or spill beverage on it.

Do not install the camera under unstable lighting conditions

Do not install or use the camera in an environment where the humidity is high

1. Features

WDR(Wide Dynamic Range)

Delivers a powerful Wide Dynamic Range to the camera which provides superior images, internally and externally, even under extreme light and dark contracts.

It automatically compensates the necessary light levels to get detailed information in the dark part of the image without saturation from the bright part. It enables the

WDR function to be very efficient, using a normal CCD, by using a Dual Shutter

(long & short shutter) algorithm, a specialised AE (Auto Exposure) and intelligent image processing.

700 TVL ULTRA HIGH RESOLUTION

The horizontal resolution of 700 TV Lines with 960H IT CCD. It gives a vivid image output with super high horizontal resolution using our own De-Mosaic Interpolation algorithm and a specialised built-in sharpness filter.

3D DNR(Digital Noise Reduction)

Achieves excellent 3D-DNR (3-Dimensional Digital Noise Reduction) function using upgraded 3D filtering. This function is automatically enabled when the camera is being used and provides clear and superior images in very low light luminance. Normally video noise increases in low light conditions, while the gain level of the amplifier increases. It compensates for the dynamic noise using the inactive information of a normal frame

ZERO DEFECT

Adaptive Defect Correction delivers clear picture capture in very low light luminance using two algorithms for defect pixel compensation.

Sens-Up(x512, DSS)

Achieves high quality pictures by supporting a long exposure time - more than

1/50second - and enables recognition of the shape and color of a suspended object under no light conditions - in cases where exposure time is greater than

8 seconds (x512).

POLYGONAL PRIVACY MASKING(Polygonal, 8colors)

Ensures privacy protection for private and specific areas on the video signal output using a polygonal masking function. It allows the size and position of the masking areas to be controlled very easily, and there are 8 mask areas which are user programmable - color, brightness and mosaic.

ECLIPSE

Enables the recognition of a visible car license plate by blocking unwanted light sources.

HIGH SENSITIVITY TRUE DAY&NIGHT

The Day & Night function delivers high quality color rendition and converts

automatically into monochrome as luminance levels drop.

2. Components

Super WDR/3D DNR Camera

L-Wrench

Manual

Terminal Block

WDR / 3D DNR

STANDARD CAMERA

USER’S MANUAL

WDR/3D DNR

Zero Defect

High Resolution of 600 TV Lines

Sens Up(x512, DSS)

DIS(Digital Image Stabilization)

Polygonal Privacy Masking

D.Zoom(x1~x10)

Eclipse

High Sensitivity Day&Night

3. Names and Functions of Parts

1 2 3 4

1) Front

① Lens protection cap

Please cover while it is out of use.

② CS-Mount lens adaptor

Please attach the CS-Mount lens here.

③ Back Focus clamp screw

Please loosen the clamp screw with a screwdriver before

adjusting the Back focal length.

4 Mounting bracket screw hole

Please use the screw hole when fixing the camera onto the mounting bracket. Please use the clamp screw as specified in the picture.

L

1/4"-20 UNC (20 THREAD)

L:4.5mm±0.2mm (ISO standard), or 0.197" (ASA standard)

The mounting bracket can be separated and attached to the top of the camera. In this instance please do not tighten the screw to a depth of more than 5mm, otherwise serious damage can influence in the inner parts of the camera.

DC12V, DC12V/AC24V

VIDEO

4 L

U

D

POWER

R

2

DC IRIS

+

RS 485

+

DC 12V

AC 24V

1 3 5 6

2) Back

① Auto iris lens connector

This is the connection terminal for auto iris lens.

② Video composite Out

③ Power lamp

Light up when the correct power is supplied to the camera.

④ Setting button(OSD Joystick)

ENTER button : Use for menu display. This button can

be used to confirm settings after changing the value of the

selected function or current conditions.

UP & DOWN buttons : Use for selecting items by moving

the cursor up or down on the menu screen.

LEFT(L) & RIGHT(R) buttons : Use when changing item values

by moving the cursor to the left or right on the menu screen.

⑤ RS-485(Option)

The camera can be controlled by using external controller like a remote controller.

6 Power input terminal

Connect to the power appropriate to each power

requirement, 12V DC or 24V AC or 90~240V AC.

4. Installation

1) Lens

Lenses are sold separately. Lenses such as auto iris lens,

CS-Mount lens and C-Mount lens can be used.

Note) How to operate this product effectively

• Please keep lens clean

• Any foreign objects and finger marks on the lens can cause

inferior image quality in low light conditions.

① When using an auto iris lens

Please peel off about 8mm of the outer skin of the auto iris

lens cable.

approx 8mm

Please peel off about 2mm of the outer skin of the insulated

conductor inside the lens cable.

approx 2mm

Please remove the cover of the auto iris lens connection plug and solder the lens cable to the connector pin in the plug.

Pin No.

LENS

DC

No.1 Pin

No.2 Pin

No.3 Pin

No.4 Pin

Damping-

Damping+

Drive+

Drive-

Lens cable

No. 3 Pin

No. 1 Pin

No. 4 Pin

No. 2 Pin connector

Please fit the auto iris lens connector plug and take off the lens protection cap, and then attach the auto iris lens to the camera by screwing it in clockwise.

Please insert the connection plug that is connected to the auto iris lens cable into the auto iris lens connector, which is located on the back of the camera.

② When using a CS-Mount lens

Please take off the lens protection cap and attach the

CS-Mount lens to the camera by screwing it in clockwise.

③ When using a C-Mount lens

Please take off the lens protection cap and attach the

C-mount adaptor.

2) Power

* Be sure to connect power only after all installation is complete.

* Please use a power adaptor that meets the required standards.

[Recommended - Voltage : +/-20%, Current : Adapter with

rated power of 2 times(than real using current ]

3) RS485(option)

*The camera can be controlled by using external controllers like a remote controller.

* Connect the RS485 cable(+, -) to the connection port of the

485 control that is connected to the DVR or

System Controller.

* Use the PELCO-D protocol.

* When controlling RS485, please check the following:

- Communication Speed : 4800 bps

- Data Bit Number : 8 bits

- Stop Bit Number : 1 bit

- Parity Bit : none

L

U

R

D

POWER

DC IRIS

VIDEO

+

RS 485

+

AC 24V

RS485 + RS485 -

DVR

Monitor

5. Setup Menu Flow

EXPOSURE LENS

E.SHUTTER

BLC

DC, ELC

AUTO, 1/50,1/60(NTSC),

1/100,000

ON<1~255>, OFF

WDR OFF

ON

WDR LEVEL<0~20>

WEIGHT<0~20>

AGC OFF,LOW,MID,HIGH

SENS-UP

AWC, ATW, MANUAL, PUSH COLOR

DAY&NIGHT

RETURN

WB MODE

R-Y GAIN

B-Y GAIN

RETURN

D&N MODE AUTO, DAY, NIGHT, EXT

<1, 5, 30, 60> LEAD TIME

BURST ON, OFF

RETURN

FUNCTION MIRROR ON, OFF

SHARPNESS <0~40>

GAMMA

NEGA

3D DNR

0.45, 0.6, 1.0

OFF, ON

OFF, LOW, MID, HIGH

ECLIPSE OFF

ON

SET LEVEL-LOW/MIDDLE/HIGH

HI-INV -ON/OFF

RETURN

MOTION ALARM

SET WINDOWS

ALL SET

ALL CLEAR

SENSITIV

SHOW

DELAY TIME

RETURN

OFF, ON

OFF, ICON, TRACE

<1~15>

EXPOSURE LENS

E.SHUTTER

BLC

DC, ELC

AUTO, 1/50,1/60(NTSC),

1/100,000

ON<1~255>, OFF

WDR OFF

ON

WDR LEVEL<0~20>

WEIGHT<0~20>

AGC OFF,LOW,MID,HIGH

SENS-UP

AWC, ATW, MANUAL, PUSH COLOR

DAY&NIGHT

RETURN

WB MODE

R-Y GAIN

B-Y GAIN

RETURN

D&N MODE AUTO, DAY, NIGHT, EXT

<1, 5, 30, 60> LEAD TIME

BURST ON, OFF

RETURN

FUNCTION MIRROR ON, OFF

SHARPNESS <0~40>

GAMMA

NEGA

3D DNR

0.45, 0.6, 1.0

OFF, ON

OFF, LOW, MID, HIGH

ECLIPSE OFF

ON

SET LEVEL-LOW/MIDDLE/HIGH

HI-INV -ON/OFF

RETURN

MOTION ALARM

SET WINDOWS

ALL SET

ALL CLEAR

SENSITIV

SHOW

DELAY TIME

RETURN

OFF, ON

OFF, ICON, TRACE

<1~15>

PRIVACY MASK1 OFF

ON

SETWINDOWS

COLOR SET<1~8>

MASK8 OFF

ON

SET WINDOWS

COLOR SET<1~8>

RETURN

SYNC SYNC MODE AUTO, INTER

V-PHASE <0~199>

RETURN

COMMUNICATION ADDRESS <0~255>

BAUDRATE OFF, 2400~38400

PROTOCOL PELCO-D

RETURN

SPECIAL

TITLE OFF

ON

EDIT

RESET

POSITION

LANGUAGE ENG

DPC AUTO,OFF

RETURN

EXIT SAVE&EXIT

FACTORY SET

EXIT

RETURN

6. Special Features

1. WDR(Wide Dynamic Range)

Wide Dynamic Range is essential for capturing the images at all light levels.

EXPOSURE

LENS DC

E.SHUTTER 1/60

BLC ON

WDR ON

AGC HIGH

SENS-UP MANUAL

RETURN

WDR

WDR LEVEL 11

WEIGHT 10

RETURN

1) WDR LEVEL :

You can set the WDR(Entry) LEVEL on the entry timing for this function.

You have to set the level into low number if you need a WDR function just in more strong light.

On the contrary you have to set the level into high number if you need a

WDR function just in normal conditions(or low light) without strong lights as like sunshine.

0 2 4 6 8 10 12 14 16 18 20

WDR Entry Level

(Day Time)

(0~20)

Strong Sunshine Light

(Day Time)

Middle Light

(Day Time)

Low Light

(Day Time)

※Eclipse mode should be Off while you use WDR function.

(Eclipse is just a special WDR function for car license plate)

2) WEIGHT : This is a level to make the dark area more bright.

Low number for more dark condition and high number for

more brightness condition.

2. 3D DNR(Digital Noise Reduction)

Select 3D DNR ON or OFF.

3D-DNR function reduce the background noise in a low luminance environment. Upgraded 3D filtering ensures even more clear image.

[DNR Level High : Picture image is more clear but Ghost is more increased.

DNR Level Low : Picture image is not clear but less Ghost.]

MAIN MENU

COLOR

DAY & NIGHT

FUNCTION

MOTION

PRIVACY MASK

SYNC

COMMUNICATION

SPECIAL

EXIT

FUNCTION

MIRROR ON/OFF

SHARPNESS <0~40>

GAMMA 0.45

NEGA ON/OFF

3D DNR MIDDLE

ECLIPSE OFF

RETURN

3. ECLIPSE

If there is a highlight within a limited environment such as car park,

It makes it possible to review vehicle license plates by removing the highlight.

[Only used for car license plate in low light condition and the WDR

in OSD menu should be Off mode while Eclipse work as On mode]

MAIN MENU

EXPOSURE

COLOR

DAY & NIGHT

FUNCTION

MOTION

PRIVACY MASK

SYNC

COMMUNICATION

SPECIAL

EXIT

FUNCTION

MIRROR ON/OFF

SHARPNESS <0~40>

GAMMA 0.45

NEGA ON/OFF

3D DNR MIDDLE

ECLIPSE OFF

RETURN

7. SPECIFICATIONS

TV System

S ensor

Total Pixel

Effective Pixel

Synchronization Internal

Line Lock

Scanning System

Horizontal Resolution

Min. Illumination

Sens-Up On

Video Output

γ Correction

S/N

O.S.D

Electrical Shutter

Privacy Masking

Day & Night

Motion Detection

Digital Zoom

Sens-Up(Low Shutter)

SYNC

White Balance

WDR

WDR Level

3D-DNR

MIRROR

NEGA

ECLIPSE

AGC

Lens

Operating Temperature/Humidity

Storage Temperature/Humidity

Dimension(mm)

Weight

NTSC

1/3” 960H IT CCD

1020(H) X 508(V)

976(H) X 494(V)

H/V 15.734/59.94Hz

H/V 15.750/60Hz

2:1 Interlace

700 TV Lines (Max.)

PAL

1020(H) X 596(V)

976(H) X 582(V)

H/V 15.625/50Hz

H/V 15.625/50Hz

0.12Lux(15IRE), 0.2Lux(30IRE), 0.4Lux(50IRE) F1.2

0.0002Lux(15IRE), 0.0005Lux(30IRE), 0.0008Lux(50IRE) F1.2

1.0Vp-p/ 75ohm Video 0.714Vp-p

0.45, 0.6, 1.0

More than 52dB(AGC off)

LENS,E-SHUTTER, BACKLIGHT,WDR, AGC, SENS-UP

WHITE-BALANCE, DAY&NIGHT, MOTION, MIRROR

SHARPNESS, GAMMA, DNR, ECLIPSE, PRIVACY

COMMUNICATION, SYNC, TITLE, LANGUAGE

DPC

1/60~1/100,000

8 Windows(Polygonal, 8 Colors)

1/50~1/100,000

COLOR / BW / AUTO / EXT

ON / OFF x1.0 ~x10

OFF ~x512

AUTO / INTERNAL / DIGITAL LINE LOCK

ATW / AWC / MANUAL / PUSH

ON / OFF(WDR LEVEL, WEIGHT)

120dB Max.

ON / OFF(OFF, LOW, MID, HIGH)

ON / OFF

ON / OFF

ON / OFF

LOW / MIDDLE / HIGH / OFF

C / CS Mount

-20

℃

~60

℃

/30% ~80%

-30

℃

~60

℃

/20% ~90%

DC 12V, 250mA / AC 24V, 110mA

61(W) x 55(H) x 106(L)mm

Abt 460g

Design and specifications are subject to change without notice.

PRODUCT WARRANTY CARD

1) ITEM # :

2) S/N # :

3) INSTALLATION CONDITION

- Indoor / Outdoor

- Power supply SPECIFICATION :

DC12V / AC24V

CURRENT __________ mA

4) TROUBLESHOOTING

- No picture

- Bad image

- No power

- Water damage

- LED ON / OFF

- ETC. :

* Please keep this warranty card with the manual.

* Please fill out this warranty card and send us this warranty card

with the faulty units together.

Following cases can be charged even within the warrany period. a. When defects are caused by user’s carelessness.

b. When improper or unauthorized repairs are done or when the inside is

modified or damaged. c. Defects caused by natural disaster or power problem. d. When the warranty card is not filled out or corrected unconfirmed.