COP Security 15-CAH22V Instruction Manual

High-Sensitivity 1/3” COMS 2.2

Mega-Pixel HD-SDI Camera

INSTRUCTION MANUAL

15-CAH22V

CONTENTS

PRECAUTION……………………………………………….2

FEATURES….……………………………………………….3

DIMENSION….………………………………………………3

SPECIFICATIONS…………………………………………..4

OSD MENU OPERATION INSTRUCTION……………….7

1

PRECAUTION

Do not touch the CCD directly. If necessary, use a soft cloth moistened with alcohol to wipe off dust.

Do not open or modify

Do not adjust the camera's internal circuits or power supply modules, as it may cause damage to the unit. For internal set up and repair, please consult our dealer.

Do not put objects inside the unit

Do not put metal objects or flammable substance inside the camera for it may cause damage to the unit. If water or liquid gets inside of the camera please disconnect power immediately and contact with your dealer.

Be careful when handling the unit

Do not drop the camera and avoid it from strong shock or vibration.

Install away from electric or magnetic fields

It may interfere or distort the image when camera is installed close to electric or magnetic fields. Ex: TV, Speaker, and etc.

Avoid from humidity, dust and heat a. Do not install the camera in smoky, dusty or steamy areas. b. Do not install the camera close to heat generating devices (for ex: spotlights)

Protect the camera carefully from direct exposure to sunlight, rain, and etc.

Cleaning

2

FEATURES

MODEL:15-CAH22V z HD-SDI and CVBS Dual Video Outputs z Wide Dynamic Range (WDR) z Adaptive Contrast Enhancement (ACE) z Support fog reduce / high light compensation (HLC) z Build-in Motorized Vari-focal Lens z Build-in Hi-Quality Mage-Pixel Lens z Build-in ICR Module With D/N Function z Build-in OSD Function z Dimension: 56(W)X60(H)X124(D) (mm) z Weight: 230g

DIMENSION

3

SPECIFICATIONS

MODE NO.

TV System

Image Sensor

Total Pixel size

Effective Pixel size

Lens

Scanning system

15-CAH22V

NTSC / PAL

1/3-inch CMOS image Sensor (Hi-Res)

2010(H) ×1108(V)

1944(H) ×1092(V)

Motorized Vari-focal Auto IRIS Lens 3.6~16mm

Progressive

Synchronization Internal

Resolution

Video Output

S/N ratio typical ( MAX )

Minimum scene illumination

Frame Integration

Digital output:

HD

Display Pixel

1280 × 720P

Frame Rate (fps)

60/50

Full HD 1920 × 1080P 30/25

Analog output:

System Resolution Horizontal-Frequency Vertical-Frequency

NTSC 750 TVL 15.723 MHz

PAL 750 TVL 15.625 MHz

59.94 Hz

50 Hz

HD-SDI and Analog NTSC/PAL

(Dual Video Outputs, without WDR) more then 50dB ( AGC OFF)

0.001 Lux (B/W DSS)

25 fps (PAL) , 30 fps (NTSC)

4

FUNCTION

Backlight control

AGC

(Auto GAIN Control)

ACE

(Adaptive Contrast Enhancement)

WDR

(Wide Dynamic Range)

Defog Function

DNR

HLC Control

(High Light Compensation)

Shading

Brightness

Mirror Function

Freeze Function

Sharpness

Pattern Generator

Digital Zoom

Motion Detect

Day / Night Function

Smart IR

White Balance

LENS Control

Shut Speed

DSS

(Digital Slow Shutter)

Remote OSD

Operation Temperature

Operational Humidity

Storage temperature

Power Supply

ON / OFF (Set up area to control BLC function)

ON / OFF

ON / OFF

*When ACE is on, WDR and Defog function can’t turn on.

ON / OFF

*When WDR is on, ACE and Defog function can’t turn on.

ON / OFF (0~10 steps)

*When Defog is on, ACE and WDR function can’t turn on.

OFF / Low / Middle / High / Auto

ON / OFF (0~20 steps)

ON / OFF (Select Lens shading compensation)

0 ~ 20 steps

Horizontal/ Vertical / Horizontal & Vertical

ON / OFF

Yes (0 ~ 10 steps)

ON / OFF

1X ~ 32X

Yes (4-points)

Day / Night /Auto /Ext.

ON / OFF

Auto / Preset / Manual / Indoor / Outdoor

AES / ALC

1/30 ~ 1/60,000 (sec) for NTSC , 1/25 ~ 1/60,000 (sec) for PAL

OFF / X2 / X3 / X4

Yes (Use RS485 control)

-10 ℃ TO +50 ℃ within 80 ﹪ RH

-20 ℃ TO +60 ℃

DC12V ±10% / 250mA (Max)

Weight 230g

5

Control key and function

1. POWER INPUT (DC 12V)

2. RS-485

KEYBOARD CONTROL:15-AU50EH,15-AU50H,15-AU50ES...

ICR FILTER CONTROL BY EXTERNAL WITH NO/NC

OUTPUT

OUTPUT

7. FUNCTION LED (YELLOW)

8. OSD / FUNCTION SWITCH

Press ▲▼ at the same time to enter the Lens adjusting mode

( *The yellow Led will be light ), press middle button to back OSD mode

RS485 REMOTE CONTROL

1. PROTOCOL ： PELCO-D

2. BAUD RATE ： 2400 bps

3. CAMERA ID ： ID=1 (DEFAULT)

4. OPERATING ：

4-1. ON ： CALL OSD MENU / ENTER SELECTED ITEM

( *Can use the CALL+95+ENTER key commend. )

4-2. OFF ： CLOSE OSD MENU

4-3. JOYSTICK ： UP / DOWN / LEFT / RIGHT ( ITEM SELECT )

4-4. WIDE / TELE , NEAR / FAR ： ZOOM AND FOCUS CONTROL

6

OSD Menu Operation Instruction

◆ Main Menu

MENU

MODEL D&N

EXPOSURE

WHITE BAL

IMAGE

INTELLIGENCE

SPECIAL FUNC

DISPLAY

EXIT

Functions can be setup using Menu Key of Pelco protocol.

The menu consists of the “Main Menu” and “Sub Menu”.

The main menu is displayed where 6 camera functions can be selected.

To the push of each main menu selection, the sub-menu is displayed.

◆ MODEL

MENU

MODEL D&N

EXPOSURE

WHITE BAL

IMAGE

INTELLIGENCE

SPECIAL FUNC

DISPLAY

EXIT

◈ MODEL : Select model

► D&N / COLOR / IR SMART / IR CDS

7

◆ EXPOSURE

MENU

MODEL D&N

EXPOSURE

WHITE BAL

IMAGE

INTELLIGENCE

SPECIAL FUNC

DISPLAY

EXIT

EXPOSURE

BRIGHTNESS l-------i-------l 0

LENS DC

SHUT SPEED AUTO

FLICKERLESS OFF

DSS OFF

AGC OFF

WDR/BLC OFF

DAY&NIGHT

SMART IR OFF

RETURN

◈ BRIGHTNESS : Adjust brightness level

► 0(dark) ~ 20(bright) steps

◈ LENS : Select LENS type

► DC / MANUAL

▷ MODE : In case of the indoor, will be recommended the INDOOR MODE

In case of the outdoor, will be recommended the OUTDOOR MODE

*If Shutter rolling occurs, the MODE should be changed from OUTDOOR to INDOOR

◈ SHUT SPEED : Can be set in AUTO or MANUAL

► AUTO / 1/30(25),1/60(50),1/120(100),1/240,1/500,1/1000,1/2000,1/4000,1/8000,

1/16000,1/30000,1/60000 sec

◈ FLICKERLESS : Select Flickerless mode (remove screen flicker)

► OFF / ON

◈ DSS : Select maximum DSS(Digital Slow Shutter)

► OFF / x2, x3, x4

◈ AGC : Select Auto Gain Control

► OFF / ON

◈ WDR/ BLC: Select WDR (Wide Dynamic Range) or BLC (Back Light Compensation)

► WDR

▷ WEIGHT: Adjust WDR level.

► 0 ~ 3

8

► BLC

▷ AREA: Control BLC area according to light condition.

▷ POS-X: Adjust the window X-Axis position

▷ POS-Y: Adjust the window Y-Axis position

▷ SIZ-X: Adjust the window X-Axis size

▷ SIZ-Y: Adjust the window Y-Axis size z When WDR is ON, ACE and DEFOG function will be off.

◈ DAY & NIGHT: Select Day & Night

1. D&N Model

► AUTO / DAY / NIGHT / EXT

▷ Delay: 0 ~ 255 second

▷ BURST: OFF / ON

▷ THRS: (LOW / MIDDLE / HIGH)

According to daytime, nighttime setting the levels of transition sets to no changes when it is dark at, higher the step it is set to

▷ GAP: LOW / MIDDLE / HIGH

This setting adjusts the margin of change from the setting of light to dark / daytime to nighttime and dark to light / nighttime to daytime. If this setting is too low then fluctuation may occur.

2. COLOR Model

► AUTO / DAY / NIGHT / EXT

▷ Delay: 0 ~ 255 second

▷ BURST: OFF / ON

▷ THRS: LOW / MIDDLE / HIGH

▷ GAP: LOW / MIDDLE / HIGH

3. IR SMART Model

► AUTO

▷ Delay: ---

▷ BURST: OFF / ON

▷ THRS: ---

▷ GAP: ---

4. IR CDS Model

► AUTO / DAY / NIGHT

▷ Delay: ---

▷ BURST: OFF / ON

▷ THRS: ---

▷ GAP: ---

◈ SMART IR: OFF / ON

▷ THRS: Set-up Smart IR turns on point.

When you level up the value, Smart IR turns on in a low light condition.

*SMART IR function only works with IR Smart Model.

9

◆ WHITE BAL

MENU

MODEL D&N

EXPOSURE

WHITE BAL

IMAGE

INTELLIGENCE

SPECIAL FUNC

DISPLAY

EXIT

WHITE BAL

AWB AUTO

CHROMA l-------i-------l 0

RETURN

◈ AWB: Select WHITE BALANCE mode

► AUTO / PRESET / MANUAL / INDOOR / OUTDOOR

▷ AUTO: Automatically adjusts color according to the available lighting.

▷ ONE PUSH : It is a fixed white balance mode that may be automatically

readjusted only by pressing PRESET

▷ MANUAL: Color can be corrected when the user increases or decreases

“RED GAIN” or “BLUE GAIN”.

► RED GAIN: Adjust R gain value 0 ~ 20

► BLUE GAIN: Adjust B gain value 0 ~ 20

▷ INDOOR: Set color temperature to be Indoor light (3700°K)

▷ OUTDOORS: Set color temperature to be Outdoor light (5100°K)

◈ CHROMA: Adjust CHROMA gains value

► 0 ~ 20 steps

10

◆ IMAGE

MENU

MODEL D&N

EXPOSURE

WHITE BAL

IMAGE

INTELLIGENCE

SPECIAL FUNC

DISPLAY

EXIT

IMAGE

SHARPNESS 5

MIRROR OFF

FREEZE OFF

E.ZOOM X1

HLC OFF

ACE OFF

DNR AUTO

D.COMPRESS OFF

GAMMA 0.50

RETURN

◈ SHARPNESS: Adjust sharpness level

► 0 ~ 10 steps

◈ MIRROR: Select a flip mode

► OFF / H / V / H&V

▷ H: You can flip the picture horizontally on the screen

▷ V: You can flip the picture vertically on the screen

▷ H&V: You can flip the picture horizontally & vertically on the screen

◈ Freeze: Select real or still mode

► OFF / ON

◈ E.ZOOM: Select maximum digital zoom magnification.

► x1 ~ x12, x14, x15, x18, x21, x25, x32

◈ HLC: Select High Light Compensation.

When extremely bright light is projected to the camera masking is used on the

Portion to prevent partial saturation on the monitor.

► OFF / ON

▷ ON LEVEL: 0 ~ 20 steps

COLOR: Black, White, Yellow, Cyan, Green, Magenta, Red, And Blue

◈ ACE: Select Digital WDR (Wide Dynamic Range)

► OFF / ON

*When ACE is ON, WDR and DEFOG function cannot turn on.

◈ DNR: Select Digital Noise Reduction

► AUTO / OFF / LOW / MIDDLE / HIGH

◈ D.COMPRESS: Video image data compression function.

Please use this function only IP camera.

► OFF / ON

11

◈ GAMMA : Select GAMMA

► 0.45 / 0.50 / 0.55 / 0.6 / 0.65

◆ INTELLIGENCE

MENU

MODEL D&N

EXPOSURE

WHITE BAL

IMAGE

INTELLIGENCE

SPECIAL FUNC

DISPLAY

EXIT

INTELLIGENCE

PRIVACY OFF

MOTION OFF

RETURN

◈ PRIVACY: Hide an area you want to hide on the screen

► OFF / ON

▷ MASK#: Select mask area number (0 ~ 31)

▷ MODE: Mask enables or disable (OFF / ON)

▷ X-POS: Adjust the mask X-Axis position

▷ Y-POS: Adjust the mask Y-Axis position

▷ X-SIZ: Adjust the mask X-Axis size

▷ Y-SIZ: Adjust the mask Y-Axis size

▷ COLOR: Cyan, Green, Magenta, Red, Blue, Black, White, And Yellow

▷ TRANS: Select mask transparency level (0 ~ 4)

◈ MOTION: When there is movement of the subject in the screen, there will be an

Motion detection

► OFF / ON

▷ SENSITIVITY: Adjust sensitivity of MD (0 ~ 20 steps)

More sensitive to setting to low step with sensitivity

▷ AREA: Designate motion detection area (WHOLE / EACH)

▷ AREA#: Setting 3 areas (0~2) of motion detection

▷ MODE: Limit and define areas of motion detection

▷ X-POS: Adjust the AREA X-Axis position

▷ Y-POS: Adjust the AREA Y-Axis position

▷ X-SIZ: Adjust the AREA X-Axis size

▷ Y-SIZ: Adjust the AREA Y-Axis size

▷ TRANS: Adjust color tone of out of selected areas.

▷ INTERVAL :Select the alarm interval time (0 ~ 255sec)

▷ DWELL : Select the duration time about changing MD mode (0 ~ 255sec)

▷ RETURN

12

◆ SPECIAL FUNC

MENU

MODEL D&N

EXPOSURE

WHITE BAL

IMAGE

INTELLIGENCE

SPECIAL FUNC

DISPLAY

EXIT

SPECIAL FUNC

SHADING DET OFF

SHADING OFF

DEFECT DET OFF

DEFOG OFF

SYSTEM NTSC

HD FORMAT 1080P

PG OFF

CVBS ON

COMM

DEFAULT ON

RETURN

◈ SHADING DET : Sets the shading calibration that the lens will perform.

Only occurs when the entire screen is viewed in white

light. (OFF / ON)

◈ SHADING : Select Lens shading compensation. (OFF / ON)

◈ DEFECT DET : Compensates for bad pixels that my occur. Occurs when the

whole screen is in full black or if there is bad pixelation and it changes the

THRS values until the screen is fixed. (OFF / ON)

*If you use a DC lens what closed IRIS, you do not need to block the lens while operating DEFECT function. In case of using a DC lens not closed and manual lens, you have to block the lens while operating DEFECT function.

◈ DEFOG : Carry out defog function

► OFF / ON

▷ LEVEL : Eliminate amount of fog on display screen.

0 ~ 10

* When DEFOG is ON, ACE and WDR function can not turn on.

◈ SYSTEM : Select NTSC or PAL. (NTSC / PAL)

◈ HD FORMAT : Select Digital output 1080P or 720P. (1080P / 720P)

◈ PG : Select Color pattern generator. (OFF / ON)

◈ CVBS : Select Composite signal. (OFF / ON)

13

◈ COMM : Set up the camera ID, baud rate, protocol

▷ ID : Select the camera ID

► 1 ~ 255

▷ BAUD RATE : Select serial communication speed

► 2400 / 4800 / 9600 / 19200 / 38400 / 57600 / 115200bps

▷ PROTOCOL : Select operating protocol

► PELCO-D / PELCO-P / UPDATE

◈ DEFAULT : All the settings will be restored to the factory default.

◆ DISPLAY

MENU

MODEL D&N

EXPOSURE

WHITE BAL

IMAGE

INTELLIGENCE

SPECIAL FUNC

DISPLAY

EXIT

DISPLAY

DISP SEL

SET TITLE

RETURN

◈ DISP SEL : Select display item.

► ID : OFF / ON

► TITLE : OFF / ON

► EZOOM : OFF / ON

◈ SET TITLE : Select camera title menu (Text edit)

A B C D E F G H I J K L M N O P Q R S T

U V W X Y Z a b c d e f g h i j k l m n

o p q r s t u v w x y z , . ( ) { } [ ]

0 1 2 3 4 5 6 7 8 9 * + - / = ~ ! ? " '

S P B S C L R P O S

RETURN

VER :2012/07/23

14