Agriframes 50172 Assembly Instructions

Assembly Instructions for 12ft Landscape Monet Wall Arch

Product code: 50172

Please read these instructions carefully. They are designed to make assembly quick and easy. Please check you have received all the components and refer to the diagrams.

Number Component

2

2

¼ hoop (plain ends)

¼ hoop (reduced one end)

2

6

84” upright

22” spacer bar (1” width)

22½” spacer bar (

7

/

8

” width) 1

2

1

3

6” fixing tube (reduced one end)

Holemaker

5x4 Lattice

Assembly requires a rubber mallet, Phillips screwdriver, spirit level and tape measure.

Installation will require a club hammer or similar and a drill.

1) Tap an end plug into the bottom of each upright. Place two ½” screws in each T joint, but only tighten the screws enough to hold them in. Make sure the screw points do not protrude into the inside of the joints as they will scratch the coating when they are attached to the tubes. (The third hole of each joint is used during final assembly).

2) Tap a T joint onto both ends of the 22½” spacer. Place the bar on a flat surface and make sure the joints are parallel. When the joints are fully connected there should be 18½” of tube left exposed (as illustrated).

18½”

3) Take the four quarter hoops, four of the 21¾” spacers, eight Opto joints and the spacer assembly from above. Refer to the diagrams on the next page and assemble the roof section of the arch. Measure the diagonals to ensure the structure is square. Note that the spacer with the

T joints goes on the side of the arch that will be attached to the wall, as shown in the diagram.

4) Place the assembled roof section in the site you intend to position the arch, so that it is up against the wall and mark out the positions of the two uprights. Use the Holemaker provided to make 15” deep holes at the marks. Ensure the holes are the same depth and vertical.

5) Take the two 84” uprights, the remaining two 21¾” spacer bars and four Opto joints. Place one upright in each hole, end plug down. Check that the tops of the uprights are level. Attach the spacers to the uprights using the joints as shown.

6) Slide a moisture seal onto the top of each upright and connect the roof section onto the uprights. Slide the moisture seals up to cover the tube joins.

7) Connect the 6” tubes into the roof and mark the position of the fixing screws on the wall.

Remove the two 6” tubes and drill the holes. Place a rawl plug in each hole.

8) Slide a moisture seal onto the reduced ends of the 6” tubes and connect them to the roof again.

Slide the moisture seals up to cover the joins and then attach the arch to the wall using the screws and washers provided.

Agriframes, Journal house, Hartcliffe Way, Bristol, BS3 5RJ

Order line: 0845 260 44 50 Fax: 0117 934 17 91

Order on-line: www.agriframes.co.uk

9) If you purchased the lattice infill, refer to the diagram on the next page and attach it using the ties provided.

10) Finally place a third screw in each T joint, check that all the joints are fully tightened and that all sections of the arch are level, and make any adjustments necessary.

PACKING REFERENCE:

Code/Product

Number

Description

Kit Component

Details

Code

AGRIFRAMES KIT COMPONENT PACKING CHECK LIST

50172

12ft Monet Wall Arch (L/S)

Kit Number as referred to in main instructions

Description DRAWINGS

Quan tity

AGR-A610/29 1x7/8" T- Connector Joint Black 2 Checked

AGR-A610/38

AGR-A610/08

AGR-A73/009

AGR-A73/013

AGR-A70/011

AGR-A610/44

1” Moisture Seal Black

1” End Plug Black

No 10x1/2" Pozi Pan

S/Tapp AB Screw BZP

No 10x2 ½

Slotted

Round W/Screw Brass

No.10 Rawl Plug

1" Saddle Washers

AGR-A40/014

6.5" Length(s) of Black

Tube Punched+Swaged One End

6

4

4

4

4

4

2

Checked

Checked

Checked

Checked

Checked

Checked

Checked

AGR-A622/37

Opto T-Joint Coated - Two Halves with Nut & Bolt 12 Checked

AGR-A70/009 6mm Allen Key

Authorised Packing Stamp:

PACKING REFERENCE :

Customer Note:

In the unlikely event that there is any of the above components missing or are faulty please contact our

Customer Helpline Number on 0845 260 44 50 and where possible quote the component code number to help us deal with your query promptly.

1 Checked