GA0688-1

Flat Bed Extra-Heavy Duty

Compound-Feed Lockstitch Sewing Machine

Instruction Manual

Parts Catalog

SHANGHAI BIAOZHUN HAILING SEWING MACHINERY CO.,LTD.

≡ CONTENT ≡

1. PRECAUTIONS FOR USER ……………………………………………………………………………………1

■ Safety precautions………………………………………………………………………………………1

■ Precautions before starting operation…………………………………………………………… 1

■ Precautions for operating conditions …………………………………………………………… 1

2. SPECIFICATION ……………………………………………………………………………………………1

3. PREPARATION FOR OPERATION ……………………………………………………………………………2

■ Cleaning the machine …………………………………………………………………………………2

■ Examination………………………………………………………………………………………………2

■ Lubrication………………………………………………………………………………………………2

■ Testing……………………………………………………………………………………………………2

4. HOW TO ATTACH A NEEDL………………………………………………………………………………… 2

5. WINDING OF BOBBIN THREAD………………………………………………………………………………3

6. ADJUSTMENT OF THE BOBBIN WINDER ……………………………………………………………………3

■ In case of uneven winding……………………………………………………………………………3

■ Winding amount of thread…………………………………………………………………………… 3

■ Winding strength……………………………………………………………………………………… 4

7. THREADING …………………………………………………………………………………………………4

8. REMOVING AND INSERTING THE BOBBIN …………………………………………………………………4

■ Removing …………………………………………………………………………………………………4

■ Installation ……………………………………………………………………………………………4

9. ADJUSTING THE THREAD TENSION…………………………………………………………………………4

■ Tension of the Upper thread…………………………………………………………………………5

■ Tension of the lower thread…………………………………………………………………………5

10. ADJUSTMENT OF PRESSER PRESSURE ……………………………………………………………………5

11. ADJUSTMENT OF WALKING FOOT AND PRESSER FOOT …………………………………………………6

12. ADJUSTMNET OF STITCH LENGTH

AND FORWARD/BACKWARD SEWING ………………………………………………………………………6

13. FEED DOG HEIGHT ………………………………………………………………………………………6

14. ADJUSTING THE HEIGHT OF THE NEEDLE BAR …………………………………………………………7

1. PRECAUTIONS BEFORES STARING OPERATION

1) Safety precautions ：

(1) When turning the power on, keep your hands and fingers away from the area around/under the needle and the area around the pulley.

(2) Power must be turned off when the machine is not in use, or when the operator leaves the seat.

(3) Power must be turned off when tilting the machine head, installing or removing the “V” belt, adjusting the machine, or when replacing.

(4) Avoid placing fingers, hairs, bars etc., near the pulley, “V” belt, bobbin winder pulley, or motor when the machine is in operation.

(5) Do not insert fingers into the thread take-up cover, under/around the needle, or pulley when the machine is in operation.

(6) If a belt cover, finger guard, eye guard are installed, do not operate the machine without these safety devices.

2) Precautions before starting operation ：

(1) If the machine’s oil pan has an oil sump, never operate the machine before filling it.

(2) If the machine is lubricated by a drop oiler, never operate the machine before lubricating.

(3) When a new sewing machine is first turned on, verify the rotational direction of the pulley with the power on. (The pulley should rotate counterclockwise when viewed from the pulley)

(4) Verify the voltage and (single or three) phase with those given on the machine nameplate.

3) Precautions for operating conditions ：

1) Avoid using the machine at abnormally high temperatures （ 35 ℃ or higher ） or low temperatures （ 5 ℃ or lower ） .

2) Avoid using the machine in dusty conditions.

2 、 SPECIFICATION

Max. sewing speed (r.p.m)

Needle No.

Needle bar stroke (mm)

Thread take-up lever stroke (mm)

Stitch length (mm)

By hand (mm)

Presser-foot stroke

By knee (mm)

Shuttie hook

Lubrication

─ 1 ─

800 r.p.m

DY × 3 26#

56

96

0-15

13

20

KSP-204N

Manual

3 、 PREPARATION FOR OPERATION

（ 1 ） Cleaning the machine

Before leaving the factory, the machine parts are coated with rust-preventive grease, which may be hardened and contaminated by dust during storage and shipment. This grease must be removed with gasoline.

（ 2 ） Examination

Though every machine is confirmed by strict inspection and test before leaving the factory, the machine parts may be loose or deformed after long distance transportation with jolt. A thorough examination must be performed after cleaning the machine. Turn the pulley to see if there is running obstruction, parts collision, uneven resistance or abnormal noise. If these exist, adjustment must be made accordingly before run-in operation.

（ 3 ） Lubrication (Fig.1)

When a new sewing machine is used for the first time, or sewing machine left out of use for considerably long time is used again, replenish a suitable amount of oil to the portions indicated by arrow in below figure.

CAUTION ： Please use white spindle oil.

Always keep the presser lifted before attempting a dry run.

（ 4 ） Testing

Fig.1

In order to get the best working situation, run the sewing machine in a low speed for about 1 month after lubricated fully. Then increase the speed to the need one.

4 、 HOW TO ATTACH A NEEDLE (Fig.2)

CAUTION ： Before using the following procedures, be sure to turn the power switch off.

The needle used by this sewing machine is DY × 3 26# 。 During operation, proper needle can be chosen according to the sewing thread.

（ the sewing thread should be able to pass the pinhole.

）

─ 2 ─

3

3

Fig.2

5 、 WINDING OF BOBBIN THREAD (Fig.3)

(1) Push the bobbin ③ on the bobbin winder shaft as far as it will go.

(2) Bring the thread forward toward the bobbin

and wind from below in clockwise direction several times around the bobbin.

(3) Push the lever ⑤ toward other side so that

the driving wheel and driven wheel will engage

and then start the machine.

(4) The driven wheel will automatically be free from the driving wheel and stop after the bobbin is filled with thread.

6 、 ADJUSTMENT OF THE BOBBIN WINDER (Fig.3)

Fig.3

(1) In case of uneven winding

If the thread dose not wind evenly on the bobbin, loosen the nut ① and move the bracket ② to the right or to the left as may be required, then tighten the nut.

(2) Winding amount of thread

Adjusting ⑥ can increase or decrease the amount of thread wound on the bobbin.

─ 3 ─

(3) Winding strength

Strength of the winding can be adjusted with the nut ① .

7 、 THREADING (Fig.4)

Raise the needle bar to its highest position and route the upper thread in the order illustrated below.

Fig.4

8 、 REMOVING AND INSERTING THE BOBBIN

(1) Removing:

Open the shuttle race cap and the bobbin holder, then take out the bobbin.

(2) Installation:

5

Put the bobbin in the rotary hook case, Permit about 5 cm of bobbin thread to hand down freely. Install the bobbin in the bobbin case so that the thread wound direction is clockwise. Then close the rotary hook and the shuttle race cap.

9 、 ADJUSTING THE THREAD TENSION (Fig.5)

─ 4 ─

For ordinary stitching, the tension of the upper and the lower threads should be equal.

(1) Tension of the Upper thread

Fig.5

Before adjusting the tension of the upper thread, be sure that presser foot is let down. To adjust tension, turn serrated nut on tension device to the right (clockwise) to increase tension and to the left (counter-clockwise) if you desire to decrease the tension.

(2) Tension of the lower thread

The lower thread tension is controlled by the larger screw near the end of the spring at the outside of the bobbin case. Turning this screw to the right (clockwise) will increase the thread tension, while turning it to the left (counter-clockwise) will decrease the tension.

10 、 ADJUSTMENT OF PRESSER PRESSURE (Fig.6)

(1) Pressure should be adjusted according to the

material to be sewn.

(2) Pressure on both the walking foot and the presser foot can be adjusted. (The adjusting Fig.6 screw has been set before shipment.)

(3) Sewing pressure should be adjusted to the minimum required strength.

─ 5 ─

11 、 ADJUSTMENT OF WALKING FOOT AND PRESSER FOOT (Fig.7)

(1) The alternating movement on the walking foot and presser foot can be adjusted by changing

the position relations of the parts of the presser

foot lifting mechanism.

(2) Changing the position relation of the connecting

link 2 and the crank 3 can complete the adjustment.

(3) Adjustment should be changed according to the thickness of the material to be sewn..

Fig.7

12 、 ADJUSTMENT OF STITCH LENGTH AND FORWARD/BACKWARD

SEWING (Fig.8)

(1) Adjusting the stitch length adjusting bolt can

change the stitch length.

(2) Stitch length can be adjusted between 0-15mm.

(3) Setting the stitch length adjusting bolt above

“ 0 ” can backstitch.

13 、 FEED DOG HEIGHT (Fig.9)

The feed dog should be 1.5 mm higher than the vertex of the needle plate. Adjustment of the feed dog height can be done as follows:

(1) Turn the machine pulley so as to raise the feed dog

to its highest point.

(2) Loosen the screw of the feed dog and adjust the

height by raising or lowering it. Then tighten the screw.

Fig.9

─ 6 ─

Fig.8

14 、 ADJUSTING THE HEIGHT OF THE NEEDLE BAR (Fig.10)

When the needle bar is at its highest point, normally the measurement between the highest point of the needle plate and the needlepoint is 28 mm. When this distance need to be adjusted, the steps is as follows:

(1) Take down the face plate, adjust the needle bar to

its highest position.

(2) Loosen the screw of needle bar connecting stud

screw.

(3) Adjust the needle bar to the right position.

(4) Tighten the screw.

Fig.10

─ 7 ─

A.

ARM BED AND ITS ACCESSORIES

─ 8 ─

A.

ARM BED AND ITS ACCESSORIES

Fig. Part No.

A01 H7208B8001 Arm

A02 H0308B8001 Bed

A03 H7215B8001 Oil pipe

A04 H7216B8001 Oil wick

Description

A05 HA307B0674 Rubber plug

A06 H7217B8001 Needle bar guide bracket stud bushing

A07 HA100C2020 Set Screw

A08 HA100C2020 Set Screw

A09 H7218B8001 Presser bar bushing

A10 HA305E0662 Set Screw

A11 H7219B8001 Pin

A12 HA100C2020 Set Screw

A13 H7220B8001 Mandril of needle bar guide bracket

A14 H2405D0664 Set Screw

A15 H7225B8001 Arm side cover

A16 HA100B2060 Screw

A17 H7236B8001 Face plate

A18 H7238B8001 Screw

A19 H7240B8001 Thread guide

A20 H3410C301K Screw

A21 HA115B0702 Nut

A22 H7241B8001 Tension spring

A23 HA310B0705 Tension disc

A24 H7242B8001 Tension screw stud

A25 H2010J0066 Tension nut

A26 H7243B8001 Thread tension regulator complete base

A27 HA111G0683 Screw

A28 H7244B8001 Tension releasing disc

A29 H7245B8001 Screw

A30 H7246B8001 Thread guide

A31 HA115B0702 Tension nut

A32 H7241B8001 Tension spring

A33 H7248B8001 Washer

A34 H7249B8001 Felt

A35 H7250B8001 Damping plate

A36 H7251B8001 Tension screw stud

A37 HA710N0683 Nut

A38 H7254B8001 Thread take-up spring

A39 H7253B8001 Spring

A40 H7255B8001 Thread take-up spring guide plate

A41 H3410C301K Screw

A42 H7257B8001 Screw

A43 H7258B8001 Nut

─ 9 ─

Pcs.

1

1

1

3

2

1

Remarks

1 SM15/64(28)×10

1 SM15/64(28)×10

1

1 SM15/64(28)×4.5

1

1 SM15/64(28)×10

1

1 SM15/64(28)×14

1

1 SM11/64(40)×9

1

2 SM15/64(28)×22

1

1 SM9/64(40)×6.5

1

1

2

1

1 SM9/32(28)

1

2 SM11/64(40)×12

1

1

1

1

1

2

2

1

1

1 SM15/64(28)

1

1

1

1 SM9/64(40)×6.5

1

1 SM1/8(44)

A.ARM BED AND ITS ACCESSORIES

Fig. Part No.

A44 H7259B8001 Tension spring

Description

A45 H7260B8001 Tension disc

A46 H7261B8001 Thread tension regulator complete base

A47 HA7311CC06 Screw

A48 H7262B8001 Thread guide

A49 H3410C301K Screw

A50 HA300B2100 Rubber plug

─ 10 ─

Pcs.

1

1

1

1 SM9/64(40)×6

1

Remarks

1 SM9/64(40)×6.5

1

B.

NEEDLE BAR AND THREAD TAKE-UP MECHANISM

─ 11 ─

B.NEEDLE BAR AND THREAD TAKE-UP MECHANISM

Fig. Part No.

B01 H7204C8001 Pulley

B02 H7205C8001 Screw

B03 H7206C8001 Screw

B04 H7208C8001 Arm shaft

B05 HA108G0661 Collar

B06 HA105D0662 Set Screw

B07 H7209C8001 Thread take-up cam

Description

B08 H7210C8001 Needle bar connecting base link screw

B09 H403060120 Screw

B10 H4933K8001 Set Screw

B11 H602040450 Pin

B12 H7211C8001 Thread take-up lever

B13 H7212C8001 Screw

B14 H7213C8001 Roller

B15 H7214C8001 Roller pin

B16 H2010J0066 Nut

B17 H007013050 Retaining ring-E type

B18 H7215C8001 Needle bar connecting link screw

B19 H2010J0066 Nut

B20 H7216C8001 Needle bar connecting link

B21 H7217C8001 Needle bar connecting stud

B22 H7218C8001 Set Screw

B23 H7219C8001 Needle bar

B24 HA700F2100 Screw

B25 H7220C8001 Needle

B26 H7222C8001 Needle bar guide bracket

B27 H7223C8001 Needle bar guide bracket pin

B28 H7224C8001 Oil wick

B29 H7225C8001 Needle bar guide bracket plate

B30 H3208G0676 Screw

B31 HA111G0683 Screw

B32 H7226C8001 Needle bar guide bracket plate base

B33 H415060140 Screw

B34 H7213B8001 Bushing

B35 H2405D0664 Set Screw

B36 H7214B8001 Felt

B37 H7212B8001 Bushing

B38 H2405D0664 Set Screw

B39 H7211B8001 Bushing

B40 H2405D0664 Set Screw

Pcs.

1

放附件箱中

1

放附件箱中

1 放附件箱中

1

1

Remarks

2 SM1/4(40)×6

1

1

2 GB/T68 M6×12

2 SM1/4(40)×10

1 GB/T117 4×45

1

1

1

1

1 SM9/32(28)

1 GB/T896 5

1

1 SM9/32(28)

1

1

2 SM1/4(40)×4.5

1

1 SM11/64(40)×7

1 DY*3 26#

1

1

1

1

1 SM15/64(28)×10.5

1 SM11/64(40)×12

1

1 GB/T70.1 M6×14

1

1 SM15/64(28)×14

3

1

1 SM15/64(28)×14

1

1 SM15/64(28)×14

─ 12 ─

C.LOWER SHAFT MECHANISM

─ 13 ─

C.

LOWER SHAFT MECHANISM

Fig. Part No.

C01 H7204D8001 Eccentric

C02 H7205D8001 Set screw

C03 H7206D8001 Pin

C04 H415060250 Screw

C05 H4728H8001 Washer

C06 H7237D8001 Bearing

C07 H7207D8001 Eccentric cover

Description

C08 H2000B2050 Screw

C09 H7208D8001 Crank connecting rod

C10 H7209D8001 Crank connecting rod pin

C11 H7210D8001 Pin

C12 H7211D8001 Screw

C13 H7213D8001 Shuttle shaft

C14 H7214D8001 Plate

C15 H7215D8001 Plate

C16 H7216D8001 Screw

C17 H2000M0120 Nut

C18 H7218D8001 Inside shaft

C19 H7219D8001 Oil wich

C20 H7220D8001 Rivet

C21 H7222D8001 Lower shaft crank

C22 H415080200 Screw

C23 H7223D8001 Shuttle shaft slide block

C24 H7224D8001 Screw

C25 H2010J0066 Nut

C26 H0305D8001 Lower shaft

C27 HA108G0661 Collar

C28 H7239D8001 Set screw

C29 H0306D8001 Shuttle driver

C30 H602040220 Pin

C31 H7228D8001 Bobbin

C32 H0307D8001 Shuttle hook base

C33 H0308D8001 Felt

C34 H0309D8001 Screw

C35 H0310D8001 Shuttle race body

C36 H7231D8001 Screw

C37 H7232D8001 Spring

C38 H0311D8001 Shuttle race cap

C39 H7234B8001 Bushing

C40 HA100C2020 Set screw

C41 HA3411D308 Set screw

C42 H7229B8001 Bushing

C43 HA100C2020 Set screw

─ 14 ─

1 GB/T70.1 M8×20

1

1

1 SM9/32(28)

1

1

2 SM1/4(40)×3.5

1

1 GB/T117 4×22

1

1

1

1 SM15/64(28)

1

2 SM3/16(28)

2

1

1

1 SM15/64(28)×10

1 SM15/64(28)×7

1

1 SM15/64(28)×10

Pcs.

1

Remarks

1 SM15/64(28)×12

2

2 GB/T70.1 M6×25

2

1 K43×48×17(NTN)

1

2 SM11/64(40)×9

1

1

1

1 SM3/16(32)×18

1

1

1

2

2 SM11/64(40)

1

1

1

1

C.LOWER SHAFT MECHANISM

Description Fig. Part No.

C44 H2405D0664 Set screw

C45 H7240D7101 Shuttle hook

─ 15 ─

Pcs. Remarks

2 SM15/64(28)×14

1 KSP-204N(

佐文）

D.

FEEDING MECHANISM

─ 16 ─

D.FEEDING MECHANISM

Fig. Part No.

D01 H0334E8001 Feed cam

D02 H7206E8001 Set screw

D03 H7207E8001 Feed cam cover

D04 H2000B2050 Screw

Description

D05 H0304E8001 Feed forked connection

D06 H7209E8001 Feed forked connection crank pin

D07 H2010J0066 Nut

D08 H7210E8001 Stitch length connecting link

D09 H7211E8001 Stitch length connecting link crank pin

D10 H415050140 Screw

D11 H0335E8001 Stitch length adjusting pin

D12 H0305E8001 Spring

D13 H0306E8001 Screw bar

D14 H2010J0066 Nut

D15 H0307E8001 Hook

D16 H0336E8001 Damping plate

D17 HA104G0012 Screw

D18 H0337E8001 Spacer

D19 H5715B8001 Screw

D20 H7214E8001 Stitch length adjusting bolt

D21 H7215E8001 Stitch length limited plate

D22 H7216E8001 Nut

D23 HE00001032 Metal ball

D24 H7217E8001 Spring

D25 HF01080320 Plastic ball

D26 H003008080 Nut

D27 H0308E8001 Feed driving rock shaft crank

D28 H415060140 Screw

D29 H0309E8001 Screw

D30 H2010J0066 Nut

D31 H0310E8001 Collar

D32 HA108G0661 Set screw

D33 H7239D8001 Crank pin

D34 H0312E8001 Feed dog base

D35 H0313E8001 Crank shaft

D36 H0314E8001 Oil wick

D37 H2100I2070 Screw

D38 H0315E8001 Collar

D39 H7214H8001 Screw

D40 H0316E8001 Crank

D41 H415060140 Screw

D42 H0317E8001 Feed dog

D43 HA7311CC06 Screw

─ 17 ─

Pcs.

1

Remarks

2 SM15/64(28)×6

1

2 SM11/64(40)×9

1

1

1 SM9/32(28)

1

1

1 GB/T70.1 M5×14

1

1

1 SM9/32(28)

1 SM9/32(28)

1

1

2 SM3/16(28)×12

1

1 SM11/64(40)×8

1

1

1

1 GB/T308 3.175

1

1 JB/T7271.1 M8×32

1 GB/T6172.1 M8

1

2 GB/T70.1 M6×14

1

1 SM9/32(28)

1

1

2 SM1/4(40)×3.5

1

1

1

1 SM3/16(32)×7

1

2 SM11/64(40)×4.5

1

2 GB/T70.1 M6×14

1

2 SM9/64(40)×6

D.FEEDING MECHANISM

Fig. Part No.

D44 H0318E8001 Feed lifting eccntric

D45 HA307C0066 Screw

D46 H0320E8001 Feed lifting connection

D47 H0321E8001 Felt

Description

D48 H20111C106 Spring

D49 H0323E8001 Screw

D50 H2010J0066 Nut

D51 H0324E8001 Crank

D52 H6017F8001 Screw

D53 H0325E8001 Feed lifting shaft

D54 HA108G0661 Collar

D55 H7239D8001 Screw

D56 H0326E8001 Crank

D57 H415060140 Screw

D58 H7219E8001 Hinge bar

D59 H007013080 Washer

D60 H0327E8001 Link

D61 H0328E8001 Needle plate

D62 HA300B2190 Screw

D63 H0329E8001 Fitting plate

D64 HA100B2200 Screw

D65 H0330E8001 Slide plate

D66 H0331E8001 Spring

D67 HA124B0713 Screw

D68 H0332E8001 Stitch length indicating plate

D69 HA104F0654 Screw

D70 H0311B8001 Bushing

D71 H2405D0664 Set screw

D72 H0312B8001 Bushing

D73 HA100C2020 Set screw

D74 H2009B0069 Bushing

D75 H2405D0664 Set screw

D76 H0312B8001 Bushing

D77 HA3411D308 Set screw

D78 H0311B8001 Bushing

D79 H2405D0664 Set screw

─ 18 ─

Pcs.

1

2 SM1/4(40)×6

1

1

1

1

1 SM9/32×28

1

Remarks

1 SM15/64(28)×18

1

1

2 SM1/4(40)×3.5

1

1 GB/T70.1 M6×14

2

2 GB/T896 8

1

1

2 SM11/64(40)×8

1

2 SM11/64(40)×8

1

1

2 SM3/32(56)×2.2

1

2 SM15/64(28)×9

1

1 SM15/64(28)×14

1

1 SM15/64(28)×10

1

1 SM15/64(28)×14

1

1 SM15/64(28)×7

1

1 SM15/64(28)×14

E.PRESSER FOOT MECHANISM

─ 19 ─

E.PRESSER FOOT MECHANISM

Fig. Part No.

E01 H7204F8001 Presser foot

E02 H7205F8001 Screw

E03 HA710P0673 Nut

E04 H7206F8001 Finger guard

Description

E05 H7207F8001 Presser bar

E06 H7208F8001 Presser bar spring

E07 H7209F8001 Thumb screw

E08 H7210F8001 Nut

E09 H7211F8001 Walking foot

E10 HA719B0709 Screw

E11 H7212F8001 Presser bar

E12 H7213F8001 Screw

E13 H7214F8001 Presser bar lifting shaft

E14 H7215F8001 Washer

E15 H7217F8001 Collar

E16 H7218C8001 Set screw

E17 H7219F8001 Bolt

E18 HF01080320 Plastic ball

E19 H7220F8001 Presser bar guide bracket

E20 H7221F8001 Connecting rod

E21 H7222F8001 Screw

E22 H609030180 Pin

─ 20 ─

Pcs.

1

Remarks

1 SM9/64(40)×14

1 SM9/64(40)

1

1

1

1 SM5/8(28)

1

1

1 SM11/64(40)×7

1

1

1

1

1

2 SM1/4(40)×4.5

1

1 JB/T7271.1 M6×20

1

1

1 SM1/4(40)×40

1 GB/T879.1 3×18

F.UPPER FEED LIFTING ROCK SHAFT MECHANISM

─ 21 ─

F.UPPER FEED LIFTING ROCK SHAFT MECHANISM

Fig. Part No. Description

F01 H7204G8001 Presser foot lifting eccentric

F02 HA307C0066 Set screw

F03 H7205G8001 Eccentric connecting link

F04 H7206G8001 Screw

F05 H7207G8001 Washer

F06 H7208G8001 Nut

F07 H7209G8001 Adjusting crank

F08 H7210G8001 Screw

F09 H7211G8001 Presser foot lifting shaft

F10 H7212G8001 Presser foot lifting shaft crank

F11 H415060140 Screw

F12 H7213G8001 Presser foot lifting connecting link

F13 H7214G8001 Screw

F14 H007013080 Retaining ring-E type

F15 H7215G8001 Presser foot lifting lever

F16 H7214G8001 Screw

F17 H7216G8001 Presser foot lifting lever base

F18 HA104G0012 Screw

F19 H7217G8001 Roller

F20 H7221G8001 Bearing

F21 H7218G8001 Screw

F22 H7219G8001 Roller base plate

F23 HA700B2060 Screw

F24 H7220G8001 Walking foot lifting connecting link

F25 H7221B8001 Bushing

F26 HA3411D308 Set screw

F27 H7222B8001 Bushing

F28 HA3411D308 Set screw

Pcs.

1

2 SM1/4(40)×6

1

1

1

1 SM11/32(28)

1

Remarks

1 SM5/16(18)

1

1

1 GB/T70.1 M6×14

1

2

4 GB/T896 8

1

2

1

2 SM3/16(28)×12

1

1 IS0 K7

1 SM15/64(28)

1

2 SM3/16(32)×8

1

1

1 SM15/64(28)×7

1

1 SM15/64(28)×7

─ 22 ─

G.NEEDLE BAR ROCKING MOTION MECHANISM

─ 23 ─

G.NEEDLE BAR ROCKING MOTION MECHANISM

Fig. Part No. Description

G01 H0304H8001 Needle bar rocking connecting link

G02 H0305H8001 Adjusting crank

G03 H415060140 Screw

G04 H7206G8001 Screw

G05 H7207G8001 Washer

G06 H7208G8001 Nut

G07 H0309E8001 Screw

G08 H2010J0066 Nut

G09 H0306H8001 Adjusting crank

G10 H415060160 Screw

G11 H7209H8001 Needle bar rock shaft

G12 H7210H8001 Collar

G13 HA105D0662 Set screw

G14 H7211H8001 Needle bar rocking crank

G15 H7218C8001 Set screw

G16 HA100C2070 Screw

G17 H7212H8001 Needle bar rocking connecting link

G18 H7214G8001 Screw

G19 H007013080 Retaining ring-E type

G20 H7213H8001 Screw base

G21 H7214H8001 Screw

G22 H7223B8001 Bushing

G23 HA3411D308 Set screw

G24 H7224B8001 Bushing

G25 HA3411D308 Set screw

Pcs.

1

1

Remarks

1 GB/T70.1 M6×14

1

1

1

1

1 SM9/32(28)

1

1 GB/T70.1 M6×16

1

2

4 SM1/4(40)×4.5

1

1 SM1/4(40)×4.5

1 SM9/32(28)×14

1

2

2 GB/T896 8

1

3 SM11/64(40)×4.5

1

1 SM15/64(28)×7

1

1 SM15/64(28)×7

─ 24 ─

H.KNEE LIFTER MECHANISM

─ 25 ─

H.KNEE LIFTER MECHANISM

Fig. Part No.

H01 H7204I8001 Knee lifter lever

H02 H7205I8001 Screw

H03 H7206I8001 Knee lifter lever base

H04 HA300J2280 Screw

Description

H05 H7207I8001 Screw

H06 H7208I8001 Knee lifter rod

H07 H7205I8001 Screw

H08 H7209I8001 Coil spring

H09 H7210I8001 Screw

H10 H7211I8001 Screw

H11 H7212I8001 Washer

H12 HA300J2280 Knee lifter lever connecting plate

H13 H7213I8001 Screw

H14 H7214I8001 Screw

─ 26 ─

Pcs.

2

Remarks

1 SM15/64(28)×6

1

2 SM15/64(28)×6.5

1 SM15/64(28)×8

1

2 SM15/64(28)×6

1

1

1 SM15/64(28)×13

1

2 SM15/64(28)×6.5

1 SM1/4(40)×3.5

1

I.

BOBBIN WINDER MECHANISM

─ 27 ─

I.BOBBIN WINDER MECHANISM

Fig. Part No.

I01 H6706N8001 Bobbin winder plate

Description

I02 H6707N8001 Pin

I03 H6708N8001 Pin

I04 H7210J8001 Bobbin winder crank shaft

I05 H7213J8001 Bobbin winder crank shaft

I06 H6713N8001 Bushing

I07 H6714N8001 Pin

I08 H6715N8001 Bobbin winder spring

I09 H007013050 Retaining ring-E type

I10 H7205J8001 Bobbin winder shaft

I11 H6717N8001 Bobbin base

I12 H7214J8001 Driven wheel

I13 H6658B8001 Friction rubber band

I14 H6720N8001 Bobbin winder lever

I15 HA100H2150 Screw

I16 H7206J8001 Winding length limited plate

I17 H3200B2100 Screw

I18 H6722N8001 Washer

I19 H6723N8001 Pin

I20 H6731N8001 Set screw

I21 H431030040 Set screw

I22 H6724N8001 Spring

I23 H6725N8001 Bobbin winder cam

I24 H7005D8001 Driving Wheel

I25 H4723D8001 Set screw

I26 H3107G0662 Screw

I27 H7208J8001 Screw

I28 HA310B0705 Tension disc

I29 HA115B0702 Nut

I30 HA115B7010 Limited plate

I31 H3300B2040 Spring

I32 H6662B8001 Thread guide

I33 H003008040 Washer

I34 H6756B8001 Blade

I35 HA500C2070 Screw

─ 28 ─

Pcs.

1

1

1

1

1

2

1

1

2 GB/T896 5

1

1

1

1

1

Remarks

1 SM9/64(40)×11

1

1

1

1

1 M5×6

2 HRC34-48 表面磷化发黑

1

1

1

2 SM15/64(28)×4.5

3 SM11/64(40)

1

2

1

1

1

1

2 GB/T6172.1 M4

1

2 SM9/64(40)×5

J.ACCESSORIES

─ 29 ─

J.ACCESSORIES

Fig. Part No.

J01 H7207K8001 Silicon oil box

J02 H7208K8001 Cover

J03 H605030400 Pin

J04 H34411C410 Screw

Description

J05 H7209K8001 Spring

J06 H3215K0693 Screw

J07 H7210K8001 Thread guide

J08 H7211K8001 Nut

J09 HA800F2020 Screw

J10 HB00001050 Hexagon socket screw key

J11 HB00001040 Hexagon socket screw key

J12 HB00001030 Hexagon socket screw key

J13 HA300J2070 Screw driver (size L)

J14 HA300J2200 Scrwe driver (size M)

J15 HA300J2210 Scrwe driver (size S)

J16 HJ02090110 Spanner

J17 HJ02100130 Spanner

J18 H7228D8001 Bobbin

J19 H7220C8001 Needle

J20 H7235K8001 Hook

J21 HPG100E202 Hook

J22 Chain

J23 HA200J2030 Thread stand assy

J24 H2004O0069 Oiler

J25 H7212K8001 Vinyl cover

J26 H0306K8001 Oil pan

J27 16250 Nail

J28 H0307K8001 Supporting bar

J29 HE009M8001 Hinge

J30 HE010M8001 Screw

J31 HE007M8001 Hinge socket

J32 16250 Nail

J33 HE005M8001 Cushion

J34 16250 Nail

─ 30 ─

Pcs.

1

1

Remarks

1 GB/T119.2 3×40

1 SM9/64(40)×4

1

1 SM9/64(40)5

2

2 SM3/32(56)

1 SM15/64(28)×13.5

1 GB/T5356 5

1 GB/T5356 4

1 GB/T5356 3

1

1

1

1 GB/T4388 9×11

1 GB/T4388 10×13

4

4 DY*3 26#

1

1

1 1100mm

1

1 聚丙烯

1

聚氯乙烯

1

6 GB349 1.6×25

1

2

4

2

4 GB349 1.6×25

4

4 GB349 1.6×25

SHANGHAI BIAOZHUN HAILING SEWING MACHINERY CO.,LTD.

ADD: No.850 Shulin Road, Songjiang District,Shanghai, P.R.China

Zip Code: 201612

Overseas Business: TEL: 86-21-64853303 FAX: 86-21-64854304

E-mail:[email protected] http://www.highlead.com.cn

The description covered in this manual is subject to change for improvement of the commodity without notice

2016.12. Printed