PR Lighting XPar 360 PR-8955 Instruction manual

XPar 360

PR-8955

This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference.

PR LIGHTING LTD. http://www.pr-lighting.com

INDEX

SAFE USAGE OF THE PROJECTOR

INSTALLING THE PROJECTOR

CONTROL SYSTEM AND POWER CONNECTIONS

DMX TERMINATOR

SETUP OPTIONS-PROJECTOR CONFIGURATION

TO SET THE DMX START ADDRESS

OPERATION MENU

DMX PROTOCOL

INDICATION OF LED DISPLAY

MAINTENANCE

TROUBLESHOOTING

TECHNICAL DATA

ELECTRICAL DIAGRAM

COMPONENT ORDER CODES

12

13

16

17

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

5

6

7

9

12

12

3

4

4

5

ACCESSORIES

These items are packed together with the projector:

Barn door

Safety cord

This manual

Signal cable

Name Quantity

1

1

1

1

Unit

Pc

Pc

Pc

Pc

Optional

Optional

Remark

2/17

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton, check there is no transportation damage before using the projector.

Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.

The projector can be used indoors and outdoors, IP20.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

Do not project the beam onto inflammable surfaces, minimum distance is 5m. 5m

Avoid direct exposure to the light from the lamp. The light is harmful to eyes.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.

Keep the optical system clean. Do not touch the LED lens with bare hands.

When the projector is hanged to a high place, please use a safety cord provided to pass through the projector handles as a secondary safety fixing for safety seasons. For details, refer to “INSTALL THE PROJECTOR “section.

LED lens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired, for example by cracks or deep scratches.

Exterior surface temperatures of the projector after 5 minutes operation is 45℃, when achieving steady state it is50℃.

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the covers removed.

Always disconnect from the mains, when the device is not in use or before cleaning it or before attempting any maintenance work !

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

3/17

INSTALL THE PROJECTOR

Lamp Hook Mounting Hole

Safety Cable

Support

When the projector is used, as the right figure above, unfold the support to certain angle and put the projector onto a flat surface. Make sure it is steady.

When the projector is used at a high place, as the left figure above, fold the support, turn it round to the top of the projector, connect a lamp hook to the mounting hole reserved in the support by screws, and then hang the hook to a high place. Eventually, use the safety cord provided to pass through the handles and hang it as a second safety fixing.

CONTROL SYSTEM AND POWER CONNECTION

DMX IN DMX OUT

DMX512

2

2

1

PIN FUNCTION

1 GND

2

DATA -

3

3

3

DATA +

Connection between the controller and a projector and between one projector and another must be made with a 2 core-screened cable, with each core having at least a 0.5mm diameter. Please use the projector’s cannon 3- pin signal input and output cables as connection. The 3-pin signal connections are connected as shown in the figure above.

Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of the plug is not connected in any way. The XPar 360 accepts digital control signals in protocol DMX512 (1990).

The amount of projectors connected in parallel is not more than 32. Connect the controller’s output to the first fixture’s input cable with a 3-pin signal cable, connect the first fixture’s output cable to the second fixture’s input cable and connect the rest fixtures in the same way. Eventually, connect the last fixture’s output cable to a DMX terminator. Note: Only when all the start addresses of fixtures are set the same, synchronous control could be achieved.

When the first fixture is not connected to the controller, and all the other connections are the same as above, it is master / slave mode connection. To achieve master / slave mode, set the first fixture master , the others salve( slave is default).

As for power connections, each projector has to be supplied separately by external power. Use the power cord of each projector to connect the mains power directly, paying attention to the voltage and frequency marked on the panel of the projector.

4/17

All of the connections are as the figure below.

Power IN

DMX Controller DMX OUT

Power IN

DMX IN

DMX OUT

Power IN

DMX IN XLR terminator

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120 (ohm) resistor connected across pins 2 and 3, which is then plugged into the output socket on the last projector in the chain. The connections are illustrated below.

2

120

3

1

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor across pins 2 and 3 in an XLR plug and insert into the DMX out socket on the last unit in the chain.

PIN 2

PIN 3

SETUP OPTIONS-PROJECTOR CONFIGURATION

FUNC

UP DOWN ENTER

Projector configuration can be set conveniently via push-button switch and LED display.

Launch the projector and press button ENTER for more than 5 seconds to unlock the panel, the LCD will show the function menu of the projector, each main menu has its submenus and each submenu has a specific function. For details, please see the “OPERATION MENU” section.

Press button UP or DOWN if you want to browse through the various Setup Options. Press button ENTER to save your settings or enter the next menu. Press button UP or DOWN to change values(add or subtract)

Press button FUNC, it will return to the upper menu one by one or browse through the main menu.

5/17

TO SET THE DMX START ADDRESS

Each Xpar360must be given a DMX start address so that the correct projector responds to the correct control signals.

This DMX start address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the controller. The Xpar360 have 3 DMX modes, which are standard mode，extended mode and short mode. For example, the standard mode has 12 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 13, No. 3 projector’s address 25, No. 4 projector’s address 37, and so on.

Launch the projector. Press button ENTER for more than 5 seconds to unlock the panel.

Press button FUNC, UP or DOWN to find “AddR” menu.

Then press ENTER to show DMX address and press UP or DOWN to set DMX address.

At this time, the address will flash continuously. Press button ENTER to confirm and it means the setting has been enabled.

Press button FUNC, it will return to the upper menu one by one.

6/17

OPERATION MENU

1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL

AddR

(DMX address)

XXX

（XXX:1~512）

CNFG

(Config settings)

dmX

(DMX mode) dISP

(Display settings) mORS

(Master /Slave Settings)

STd

(Standard mode)

EXT

(Extended mode)

SHRT

(Short mode)

ON

OFF

(Shut off digital CRT without pressing buttons in 5 minutes)

SLAV

(Slave) mAST

(Master)

INFO

(Information)

TEST

(Test mode)

FACT

(Reset factory setup)

TRmd

(Transmit parameters

)

TImE

(F ixture usage time

)

TEmP

(LED board temperature)

VER

(Version)

A

(Amber)

R

(Red)

G

(Blue)

B

(Blue)

W

(white)

ALLO

(Red/green/blue/white) dmx

(DMX mode) yES yES

XXXX

XX

X.X.X

PR XX

(Preset memory, PR01~PR16） mENU

(Operation mode)

COL1

(Colour 1)

COL2

XX

(Number: 0~14)(3)

XX

ET XX

(User memory,ET01~ET16）

(Colour 2)

COL3

(Colour 3)

COL4

(Colour 4)

(Number: 0~14)

XX

(Number: 0~14)

XX

(Number: 0~14)

Note:

1.ONLY one projector of a group connected by one signal cable could be set as Master. When the Master functions, DMX control signal should be disconnected

2.When multiple projectors’ work together in synchronous control state, Parameters can be transmitted from the master projector to the slave projectors such as DMX channel mode, Display setting status and operation mode (User memory data is included). While data transmitted, other projectors will be set as SLAVE.

7/17

3

4

5

6

7

8

Short mode

1

2

Standard mode

1

Extended mode

1

2

9

2

3

4

5

6

7

8

10

3

4

5

6

7

8

9

10

11

12

13

14

DMX PROTOCOL

FUNCTION

Dimmer

Dimmer Fine

Colour Temperature

Macro Channel

Amber

Red

Green

Blue

White

Hue

Saturation

Value

Strobe

Preset memory

DMX DESCRIPTION

000-255 Dimming from dark to light

000-255 Dimmer in 16 Bit precision

000

001-255

0

No effect

Colour temperature linear adjustment from 3200K to 10000K

No effect

001-015 Colour Temperature 3200K

016-031 Colour Temperature 5600K

032-047 Colour Temperature 7200K

048-063 Colour Temperature 10000K

064-079 Amber

080-095 Red

096-111 Green

112-127 Blue

128-143 White

144-159 Red & Green(Yellow)

160-175 Green & Blue(Cyan)

176-191 Red and Blue(Purple)

192-207 Red Green Blue and White

208-223 Full Power

224-239 Yellow and White

240-255 Amber Blue and White

000-255 Linear adjustment from dark to light

000-255 Linear adjustment from dark to light

000-255 Linear adjustment from dark to light

000-255 Linear adjustment from dark to light

000-255 Linear adjustment from dark to light

000-255 Hue selection

000-255 Saturation from shallow to deep

000-255 From dark to light

000 No effect

001-255 Strobe speed from slow to fast

000 No effect

001-015 Preset memory 1

016-031 Preset memory 2

032-047 Preset memory 3

048-063 Preset memory 4

064-079 Preset memory 5

080-095 Preset memory 6

8/17

11

12

15

16

User Memory

Memory Speed

096-111 Preset memory 7

112-127 Preset memory 8

128-143 Preset memory 9

144-159 Preset memory 10

160-175 Preset memory 11

176-191 Preset memory 12

192-207 Preset memory 13

208-223 Preset memory 14

224-239 Preset memory 15

240-255 Preset memory 16

000 No effect

001-015 User memory 1

016-031 User memory 2

032-047 User memory 3

048-063 User memory 4

064-079 User memory 5

080-095 User memory 6

096-111 User memory 7

112-127 User memory 8

128-143 User memory 9

144-159 User memory 10

160-175 User memory 11

176-191 User memory 12

192-207 User memory 13

208-223 User memory 14

224-239 User memory 15

240-255 User memory 16

001-015 Speed 1,the fastest

016-031 Speed 2

032-047 Speed 3

048-063 Speed 4

064-079 Speed 5

080-095 Speed 6

096-111 Speed 7

112-127 Speed 8

128-143 Speed 9

144-159 Speed 10

160-175 Speed 11

176-191 Speed 12

192-207 Speed 13

208-223 Speed14

224-239 Speed 15

240-255 Speed 16, the slowest

9/17

Note:

**** Channel priority from high to low is as the following: Dimming, Preset memory, User memory, ARGBW dimming,

HSV dimming, Macro channel, Color temperature.

****When high priority channel is used, low priority channel is No effect.

10/17

INDICATION OF LED CHARACTER

Decimal point of the first character

Decimal point of the third character

Decimal point of the fourth character

Parameters that LED characters display

On

Off

On

Off

On

Off

Flash

DMX signal OK

No DMX signal

Master / slave signal is OK

No master / slave signal

When setting master mode

When setting slave mode

Parameters not saved, press “ENTER” to save them

MAINTENANCE

To prolong the life of the projector, it is very important to do the maintenance work. Cooling fans must be cleaned once every 15days and external lens cleaned periodically for an optimum light output. DO NOT USE ANY SOLVENT

CONTAINING CHEMICAL ELEMENT.

Cleaning frequency depends on the environment in which the fixture operates. Soft cloth and typical glass cleaning products should be used for cleaning with care. It is recommended to clean projector at least once every 20 days.

Do not use any organic solvent, e.g. alcohol, to clean housing of the apparatus.

TROUBLESHOOTING

PROBLEM ACTION

The projector doesn’t switch on

 Power connection is not correct.

 Power supply is damaged or abnormal. Call a qualified personnel to fix it.



Connection of control board is not correct. Call a qualified personnel to fix it.

The projector can be turned on, but LEDs do not emit light and are out of control.



Connection of LED board is not correct. Call a qualified personnel to fix it.

The lamp comes on but the projector doesn’t respond to the controller

 Make sure that the projector is correctly configurated.

 Replace or repair the DMX cable.

The beam appears dim

 The projector is too hot. Take ventilation measures to make it cool.

11/17

TECHNICAL DATA

VOLTAGES:

200V/220V /230V/240V AC, 50/60Hz

Optional: 100V/120V AC, 50/60Hz

POWER CONSUMPTION:

200W@220V

LED:

Power consumption

Quantity

Manufacturers Rated LED Life

COLOURS:

3W

60（

13R＋13G＋13B＋12W＋9A）

50000 Hours

RGBWA linear color mixing with Macro

COLOR TEMPERATURE CORRECTION

Linear color temperature correction from 3200K to 10000K

DIMMER:

0-100% linearly adjustable

STROBE:

Electronic Strobe 0 ~25F.P.S

LIGHT ANGLE

Field Angle(1/10 Maximum) θ 28°

Beam Angle(1/2 Maximum) θ

1/2

15°

Lens Angle: 15° (Optional Lens Angle: 8°, 25 °, 45°

)

CONTROL:

DMX512, 3 pin interfaces

8 channels in short mode, 12channels in standard mode, and 16 channels in extended mode

Master/Salve Synchronous Control Mode

16 preset memories

16 user memories preset memories and user memories can be called by control channels,16 level speeds adjustable

Self Test Mode

OTHER FUNCTIONS:

LED board temperature display

Fixture usage time display

12/17

Parameters about DMX mode, Display setting status, operation mode can be transmitted by synchronous control.

HOUSING:

High temperature ABS +die-casting aluminum, IP20

WORK ENVIRONMENT TEMPERATURE:

-20°C~40°C

WEIGHT:

3.9kg

SIZES:

321 226

LIGHT OUTPUT:

28°lux（RGBWA)

28°lux（R)

28°lux（G)

28°lux（B)

28°lux（W)

28°lux（A)

6m

4m

2m

0m

2m

4m

6m

7m

5m

3m

1m

1m

3m

5m

7m

Distance（m）

28°Diameter（m）

0m

0

1775

309

777

26

722

124

444

77

194

6

181

31

197

34

86

3

80

14

111

19

49

2

45

8

71

12

31

1

29

5

49

9

22

1

20

3

5m

2.45

10m

4.91

13/17

15m

7.36

20m

9.81

25m

12.27

30m

14.72

14/17

NAME

LED LENS

SIGNAL CABLE

POWER SUPPLY

DRIVER BOARD

LED CONTROL BOARD

LED LAMP BOARD

COMPONENT ORDER CODES

PART NO.

070070047

230090002

190010119

230060115

230060139

230020283

QUANTITY

60

1

1

1

1

1

REMARK

15°

3meters

150W58V

15/17

16/17

PR LIGHTING LTD.

PR New Hi-tech Science Park, 1582 Xingye Avenue

Nancun Panyu, Guangzhou, 511442 China

TEL: +86-20-3995 2888

FAX: +86-20-3995 2330

P/N: 320020091

Version: 20120717

17/17