- Vehicles & accessories
- Motor vehicle electronics
- Car media receivers
- poly-planar
- MRD87i
- Instruction manual
advertisement
OWNER’S MANUAL
Version 5.0
MRD87i IPX6 Marine Radio
Poly-Planar IPX6 Marine Grade digital media entertainment system with ultimate audio 4X45 sound.
• SiriusXM-Ready ™
(SiruisXM Connect Tuner and Subscription required)
• Made For iPhone®/iPod®
• Bluetooth
• USB music player & USB charger
• SD card reader
• AM/FM digital tuner
• NOAA weather band
• USB and 3.5mm aux input inside drawer/dock
• Front and rear RCA line out
• NMEA 2000® certified
• Remote control interface
Disclaimer
•
•
Sirius,XM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights reserved. iPad, iPhone, iPod, iPod classic, iPod nano, iPod touch, and Retina are trademarks of Apple Inc., registered in the U.S. and other countries. iPad Air, iPad mini, and Lightning are trademarks of Apple Inc
T A B L E O F C O N T E N T S
Installation
Wiring Diagram
Button Description
Basic Operation
Radio Operation
SiriusXM® Operation iPod®/iPone® Operation
Bluetooth Operation
Auxiliary Operation
USB Operation
SD Card Operation
Compatible Accessories
Troubleshooting
Technical Specifications
Warranty Information
Warranty Registration
2
27
29
30
33
21
22
22
24
26
10
10
21
3
5
7
8
I N S T A L L A T I O N
IMPORTANT! Before mounting be sure there is sufficient room to accommodate the unit and that there is sufficient ventilation.
Before installing the unit, connect the wiring temporarily making sure the system works properly.
Only use the parts included with the unit to ensure proper installation.
Avoid installing the unit where it would be subject to high temperatures such as direct sunlight or hot air from heaters or the engine or where it would be subject to dust, dirt or excessive vibration.
Use the template provided to make the cutout.
With the front panel down insert the 4 provided screws. Use the 5mm nut and bracket provided to stabilize the rear of the radio.
Be sure to mount the unit to a strong, solid surface which will not give way under the stress of waves pounding the hull.
3
Optional Mounting Techniques
Optional gimbal mount bracket installation
Model # GM-MRD80
4
Optional Overhead / Under
Dash mount installation
Model # RM-10
W I R I N G D I A G R A M
SiriusXM® Tuner
(Tuner and Subscription sold separately)
MR45R (Blue)
…
Wiring Details:
Use the wired plug end (Pigtail) provided to make power and speaker connections according to the diagram below. Using this connector will make it easy to disconnect the radio for adding additional features or service. Removing the factory plug end will void warranty.
5
Wire Color
Yellow
Function
1 B+ (+12VDC)
Green w/stripe 2 Rear Left Speaker-
Green 3 Rear Left Speaker+
Red 4 ACC (+12VDC)
White w/stripe 5 Front Left Speaker-
White 6 Front Left Speaker+
Blue
Gray w/stripe
Gray
Black
7 Relay Trigger
8 Front Right Speaker-
9 Front Right Speaker+
10 Ground (Neg)
Violet w/stripe 11 Rear Right Speaker-
Violet 12 Rear Right Speaker+
Power Wire Specifications:
Yellow Wire - Connect this wire to a constant +12V source.
Red Wire - Connect this wire to a switched +12V source such as an ignition or accessory switch. (Must be connected to +12V source for unit to operate.)
Black Wire - Connect this wire to the negative battery terminal or other good power ground.
Blue Wire - This wire outputs a 12V signal when the MRD87i turns on. It is used to remotely turn on external amplifiers.
Notes:
•
Use the included plug/wire bundle to connect to the power source and speakers.
6
•
The Yellow, Red and Black power wires should be 14AWG or larger depending on the length to the battery. NEVER operate the unit without the proper power and ground wire.
•
NEVER ground the speaker leads and NEVER allow the speaker leads to come in contact with each other. The speaker wire should be at least 16 gauge or larger. Be sure to observe the correct polarity on the speaker connections
•
Use quality crimp connectors to connect wires together. Seal the connection well with electrical tape.
•
NEVER operate the unit without proper fusing. Fuse holder must be located within 2 feet from the battery. This fuse is to protect the vessel, not the electronics. In case of a short, the fuse will blow instead of the wire burning up. Using other than the recommended fuse ratings at the battery and at the unit may cause damage to the unit and will void your warranty.
•
Whenever possible, use cable ties, mounting clamps and similar wiring aids. Adding stress relief loop to wiring is also advisable to prevent straining or breakage.
•
If after reading the directions you feel uncomfortable about installing the unit, or not equipped or competent to do so, you should have this installed by a professional installer
B U T T O N D E S C R I P T I O N
7
1. Volume UP/DOWN Knob
2. - Power Button
3. IR Receiver
4. Front Panel Latch Button
5. LCD Display
6. MODE - Mode Button
7. BAND – Band Button
8. / – Control Button
9. MUTE – Mute Button
10. MENU/DISP – Menu/Display Button
11. 1/INTRO - Preset 1/Scan Button
12. 2/RANDOM - Preset 2/Random Button
13. 3/REPEAT - Preset 3/Repeat Button
14. 4/ - Preset 4/(Play/Pause) Button
15. 5/ - Preset 5/Folder down (optional)
16. 6/ - Preset 6/Folder up (optional)
17. SCAN- Scan Button
18. Live Functions/Select Knob
19. AS/PS - Auto Store and Preset Scan Button
20. SD Card Slot
21. DMD Drawer
23. RESET
B A S I C O P E R A T I O N
SWITCHING ON/OFF THE UNIT
Press button to turn on the unit. Press and hold button for 4 sec to turn off the unit
OPENING THE FRONT PANEL
Place thumb on the front panel latch button . Firmly depress the button while pulling the front panel open. Keep door firmly closed except when accessing inside drawer.
ADJUSTING THE AUDIO LEVELS
Press Volume knob to enter audio level menu then use the Volume Knob to adjust to your desired setting. Press
Volume knob again to select different functions. Unit will return to normal previous display if left untouched for 5 seconds.
RSpker (Rear Speaker) – can be set to either full range or low
8
pass full range for conventional speaker power or low pass for
MS56 subwoofer
RLineOut (Rear Line Out) – can be set to variable or fixed as required by amplifier
EQUALIZER SETTING
Press volume knob repeatedly until EQUALIZER menu appears then rotate the volume knob to select EQUALIZER setting selection.
Current Equalizer Preset Chart below. Choose one that sounds best with your speakers:
To customize your own EQUALIZER setting, please press volume knob repeatedly until EQUALIZER menu appears then rotate the volume knob to locate “CUSTOM EQ” then press the volume knob to enter your own setting. You can set each EQ Band by rotating the volume knob left or right from -10 to +10 scale
MODE SELECTION
Press MODE button to choose desired listening mode. (e.g. Radio mode to
USB mode to AUX IN mode … etc.)
MUTE
Press MUTE button to mute the sound. Press again to return to previous volume level.
DIMMER CONTROL
Press and hold MENU button for 3 seconds to display current setting.
Then use the Volume Knob to adjust to different setting.
9
Note: Firmware version level will also be displayed
RESET FUNCTION
Open front panel to display reset button. Use a ballpoint pen to press the reset button. The reset function is used in the following situations:
- All the function buttons do not operate.
- Error sign on the display.
FACTORY DEFAULT RESET
Press and hold MENU button for 3 seconds to access DIMMER CONTROL then press MENU and AS/PS button simultaneously to reset factory default settings. A warning screen will appear – press the Select knob to confirm and MENU button to cancel.
R A D I O O P E R A T I O N
SWITCHING TO RADIO MODE
Press MODE button to select radio mode.
SELECTING THE FREQUENCY BAND
In radio mode, press BAND button to locate the desired band. The reception band will change in the following order:
FM1 FM2 FM3 AM1 AM2 WeatherBand
SELECTING STATION
Press / button to select a station. To do manual tuning use
Function/Select knob .
AUTOMATIC MEMORY STORING & PRESET SCAN (AS/PS)
The PRESET buttons can be used to store 6 stations in each band (FM 1,
FM 2, FM 3 and AM1, AM2) for convenient access to your favorite stations.
Automatic Storing
Press AS/PS button , the radio searches and checks the signal strength until one cycle search is finished then the strongest stations are stored into the corresponding preset number button automatically.
Manual Storing
1. Select the desired band.
2. Select the station you want to store in memory, then press and hold one of the preset buttons for 3 seconds until the corresponding preset button number appears.
10
3. Repeat steps 1 and 2 to program additional stations.
SCAN FUNCTION
Press SCAN button to scan a station. The unit will keep on scanning every 7 seconds until you press the SCAN button again to stop scan function.
S i r i u s X M ® O P E R A T I O N
Please Note: You need SiriusXM® Tuner (sold separately) and you must activate your SiriusXM® Tuner before you can begin to receive
the SiriusXM® service.
Please connect your SiriusXM® Tuner to the SiriusXM® Tuner port located at the back of the unit.
After installing your SiriusXM® Tuner and antenna, power on your radio and then press MODE button to change to SiriusXM® mode. You should be able to hear the SiriusXM® preview channel on Channel 1. If you cannot hear the preview channels, please check the installation instructions to make sure your SiriusXM® Tuner is properly installed.
After you can hear the Preview channel, tune to Channel 0 to find the Radio
ID of your tuner. In addition, the Radio ID is located on the bottom of the
SiriusXM® Tuner and its’ packaging. You will need this number to activate your subscription. Write the number down for reference.
Note: the SiriusXM® Radio ID does not include the letters I, O, S or F.
In the USA, you can activate online or by calling SiriusXM® Listener care:
• Visit www.siriusxm.com/activatenow
• Call SiriusXM® Listener Care at 1‐ 866‐ 635‐ 2349
For Canadian Subscriptions, please contact:
• Visit www.siriusxm.ca/activatexm
• Call XM customer Care at 1‐ 877‐ 438‐ 9677
As part of the activation process, the SiriusXM® satellites will send an activation message to your tuner. When your radio detects that the tuner has received the activation message, your radio will display: “Subscription
Updated”. Once subscribed, you can tune to channels in your subscription plan. Note, the activation process usually takes 10 to 15 minutes, but may take up to an hour. Your radio will need to be powered on and receiving the
SiriusXM® signal to receive the activation message.
11
Some button functions are different when in SiriusXM® mode:
Faceplate button function assignments
SiriusXm® Function of buttons:
Live
|<<
- push to Play/Pause, hold to return to Live play
- Track Back (Replay Function), hold to Rewind
>>| - TrackUp or Live if is playing last track, hold to Fast Forward
ASPS - Display (change displaying info Ch#/Name -> Artist -> Track ->
Content - Category
Scan - push to scan all channels, hold to scan channels in current category
Band - push to change band, hold for Direct Tune
But 1-6 - Presets. Push - tune to preset, hold - save preset.
Mute - Audio Mute
Menu - push to enter Menu, hold to enter dimmer settings. In menu navigate with right encoder, select by pushing it. Press menu again to return to main screen.
SiriusXM® Mode:
Initial Channel screen (Channel Number, Preset, Time Offset and Channel
Name)
12
Press AS/PS to change metadata to Artist
Press AS/PS to change metadata to Song
Press AS/PS to change metadata to Info
Press AS/PS to change metadata to Category
13
Press and hold BAND for Direct Tune then use the Function/Select Knob to select the digits
Press and hold AS/PS to select category, use Function/Select Knob to navigate category then press Function/Select Knob to enter in selected category and browse channels using
Function/Select Knob
Press SCAN to scan all channels
14
Press and hold SCAN to scan channels in current category
Press MENU to enter then use Function/Select Knob to navigate through the available 5 options: New Password, Lock, Unlock All Ch and Signal Strength.
15
To enter password, rotate Function/Select Knob to the left to change current digit then push to go to next digit
If password is wrong, there is a Wrong password warning
ADVISORY MESSAGES:
Check tuner advisory message
16
Check antenna advisory message
No signal advisory message
Subscription update advisory message
Channel unavailable advisory message
17
Channel unsubscribed advisory message
Channel locked advisory message
SELECTING A TRACK
Press / button to select a track in Replay buffer. Press and Hold
or button to go faster.
HOW TO DIRECT TUNE
Press and hold AS/PS button “Select: 000” will show on the display.
Rotate FUNCTION/SELECT knob to change current digit, push to go to next digit. When finished, press FUNCTION/SELECT knob to confirm and play.
Example:
- If you want to search channel number 151, rotate left encoder to get 1,
18
then push left encoder to go to next digit and rotate to get 5, then push left encoder again and rotate to get 1.
- Press FUNCTION/SELECT knob to confirm and play.
SELECT A CHANNEL BY CATEGORY
Press and hold AS/PS button to enter category selection menu. Use the
FUNCTION/SELECT knob to navigate to all the categories available then when done selecting a category press FUNCTION/SELECT knob once to confirm. The unit will only play the selected category channels until you go back in category select menu and select “All channels” category.
SELECTING THE FREQUENCY BAND
In SiriusXM® mode, press BAND button to locate the desired band. The reception band will change in the following order:
S1 S2 S3
AUTOMATIC MEMORY STORING
The PRESET buttons can be used to store 6 channels in each band (S1,
S2 and S3) for convenient access to your favorite channels.
1.
Select the desired band.
2. Select the channel you want to store in memory, then press and hold one of the preset buttons for 3 seconds until the corresponding preset button number appears.
3. Repeat steps 1 and 2 to program additional channels.
PARENTAL CONTROL
You can lock any SiriusXM® channels you do not want others to have access without your permission. The default code is "0000". In case you forget your code please perform FACTORY DEFAULT RESET .
- GUIDE ON HOW TO ENTER THE CODE USING THE
FUNCTION/SELECT KNOB
Rotate FUNCTION/SELECT knob to enter first digit, push
FUNCTION/SELECT knob once and rotate to enter second digit, press
FUNCTION/SELECT knob to enter third digit and push
FUNCTION/SELECT knob again and rotate to enter last digit. When done, press FUNCTION/SELECT knob to confirm.
- TO LOCK A CHANNEL
Select a channel that you wish to lock then enter in menu and select “Lock
Channel”. Enter the code then press FUNCTION/SELECT knob to confirm.
19
- TO UNLOCK A CHANNEL
Tune to desired locked channel by entering the correct password. Then press MENU button to enter in the menu and select “Unlock Channel” then enter code again to permanently unlock channel.
- TO UNLOCK ALL LOCKED CHANNEL
Enter in menu and select “Unlock All Ch”. You will be prompted to enter the code. After entering the code all channels will be unlocked
- TO EXIT RESTRICTED MODE
Press BAND button to manually enter the channel you wish to unlock then press FUNCTION/SELECT knob. Enter the code then press
FUNCTION/SELECT knob to confirm. Now you can access all locked channels without entering password until shutdown the unit.
- TO CHANGE THE CODE
Enter in menu and select “New Code” “Enter Code” will show on the display.
Enter the old code then press FUNCTION/SELECT knob to confirm “New
Code” will show on the display. Enter your new code then press
FUNCTION/SELECT knob again “Repeat Code” will show on the display.
Repeat the code and press FUNCTION/SELECT knob to confirm.
- TO RESET SIRIUS FACTORY DEFAULT SETTINGS
Press Menu button and select “Factory Default” then enter parental control code to confirm. If you forget parental control code, please use FACTORY
DEFAULT RESET to reset radio.
DISPLAY INFORMATION
Press AS/PS button to change current displayed info on display. You can rotate through Channel Info, Artist Info, Track Info, Content info, Category info. i P o d ® / i P h o n e ® O P E R A T I O N
SWITCHING TO iPod®/iPhone® MODE
If a device is already connected:
Press MODE button to change to iPod®/iPhone® mode.
If there is no device connected the display wi ll show “No Device” please follow instructions below on how to connect your devices
Turn on your DMD device then open the front panel to connect the accessory cable to the connector on the right side of the device drawer then
20
insert your music device in the drawer. Use one of the 2 adapters available to connect your device then push the drawer back in place. If operating an iPod/iPhone® device, please connect to USB connector then press MODE button to change to iPod/iPhone® mode. If you chose the
3.5mm plug adapter press MODE button to change to AUX Input 2 mode, then refer AUX Operation on page 22 for further instructions. For iPod/iPhone® mode, refer operation instructions below:
SELECTING SONGS
Press or button to select next or previous song. Press and Hold
or button to fast forward or rewind a song.
PAUSING/PLAYING
Press 4 button to pause the play. Press 4 button again to resume play.
RANDOM
Press 2 button to start random song play
REPEAT
Press 3 button sequentially to repeat current playlist, song or turn repeat
B L U E T O O T H O P E R A T I O N
SWITCHING TO BLUETOOTH MODE
If a device is already paired:
Press MODE button to change to Bluetooth (BT) mode.
If there is no device paired the display will show “Bluetooth Not Connected” please follow instructions below on how to pair your device
1) Make sure you are close enough to MRD87i
2) Open Bluetooth setting on your device
3) Choose “Poly-Planar” from the list of available Bluetooth link
4) Enter “ 0000 ” as the Bluetooth password (if required)
5) Once connected, you can now start playing your favorite music from your music device.
6) Operating Range is up to 30’ (will vary, dependent on installation)
IMPORTANT NOTE:
Some Bluetooth-enabled devices may take more than 45 seconds to initiate after pairing or does not pair at all. If this happen, try to turn off the stereo and the device and pair it again.
21
SELECTING SONGS
Press or button or rotate Function/Select knob to select a song.
PAUSING/PLAYING
Press 4 button to pause the playing. Press 4 button again to resume playing.
A U X O P E R A T I O N
This unit can be connected to any portable music devices such as MP3
Player, TV and DVD through the AUX IN located at the back of the unit.
Press MODE button to change the mode to “AUX Input 1” (back) or “AUX
Input 2” (DMD drawer) mode.
Please note: In this mode, all controls and functions must be controlled from your music device.
U S B O P E R A T I O N
SWITCHING TO USB MODE
If there is no USB inserted in the driver:
Insert a USB through the USB port located at the back of the unit then press MODE button to change to USB mode.
If a USB is already inserted in the driver:
Press MODE button to change to USB mode.
SELECTING SONGS
Press or button or rotate Function/Select knob to select a song.
Press and Hold or button to fast forward or rewind a song.
SELECTING SONGS BY FOLDER
Note: Make sure RPT MODE is off before using this function
Press 5 button or 6 button to select folder downward or upward. If a folder does not exist or does not have music files, it will be skipped.
22
DISPLAY INFORMATION (music files only)
First line is showing mode information and the second line is displaying the song name. When browsing by rotating right functional key a folder name will be shown at the first line and track name at the second line of the display
PREVIEWING ALL TRACKS
Press 1 button to play all songs in intro mode. The unit will play the first
10 seconds of each song continuously until you press 1 button again to stop intro function.
PLAYING ALL TRACKS IN RANDOM ORDER
Press 2 button and select “Random: Track” to play all tracks in random.
Press 2 button and select “Random: Off” to cancel random function.
REPEAT FUNCTION
Press 3 button and select “Repeat: ONE” to repeat same song. Press 3 button and select “Repeat: ALL” to repeat all tracks or to stop repeat function.
PAUSE FUNCTION
Press 4 button to pause player. Press 4 button again to resume play.
IMPORTANT NOTE:
Some USB devices may not be compatible with the unit.
Some USB devices may take more than 45 seconds to initiate after plugging in. If this happen, try to remove the USB memory stick and insert it again.
23
CAUTION
If there are important files in the USB device, do not connect it to the main unit to play. Any wrong operation may cause file loss. Our company assumes no responsibility for lost files or directories.
Media type USB (can support USB2.0 but the speed is USB1.1.)
Capacity up to 2000 songs
S D C A R D O P E R A T I O N
SWITCHING TO SD MODE
If SD card is already inserted in the driver:
Press MODE button to change to SD Card mode.
If there is no SD card inserted in the driver , the display will show “No SD
Card attached”:
Insert SD card through the SD card port located in front of the unit. Press
MODE button to change to SD Card mode.
Warning! Do not over-insert the card as this can damage the contact pins.
24
Refer USB operation on pages 22 for further instructions.
REMOVING THE SD CARD
Firmly press the card into the slot and release it. The card should pop partially out of the slot.
IMPORTANT NOTE:
Some Memory Card devices may not be compatible with the unit.
Some Memory Card devices may take more than 45 seconds to initiate after plugging in. If this happen, try to remove the memory card and insert it again.
CAUTION
Be sure to use only recommended SD cards (<32GB). Using nonrecommended SD cards could cause data loss and damage your device.
If there are important files in the memory card, do not connect it to the main unit to play. Any wrong operation may cause file loss. Our company assumes no responsibility for lost files or directories.
Media type Memory Card
Capacity Standard SD: up to 1000 songs
SDHC: up to 1000 songs
Dimensions 32 × 24 × 2.1 mm
25
C O M P A T I B L E A C C E S S O R I E S ( s o l d s e p a r a t e l y )
MR45R Wired Remote Control – connect to the back of the unit labeled
“TO MR45R”. You can add up to 2 MR45R in conjunction with CMR-Y7.
MRR21 IR Wireless Remote Control - the IR eye is located next to the volume button and must be in line of site for the remote to operate.
ACX-11 USB/AUX accessory extension cable - provides easy access to your USB input and Aux input
IC-3.5PM MP3 /iPod/Satellite Radio Panel Mount Adapter - allows you to connect your MP3 player, iPod® or satellite radio to any audio device with
RCA inputs
IR-4050 IR Sensor with 9'cable - connect this IR sensor to the IR port located at the back of the unit. This is an IR sensor, another way to point your MRR21 without going to the front of the stereo.
26
T R O U B L E S H O O T I N G
PROBLEM CAUSE
No power
No sound
Cannot read some
USB devices
Blown fuse, power wires disconnected
Mute is on, Volume set at minimum, wiring is not properly connected
This unit is not 100% compatible with all
USB devices or the
USB devices has special format.
CORRECTIVE
ACTION
Check the fuse and power wire or ground wire connection
Turn Mute to off, adjust volume to a desired level, check the speaker wire
Try to format the USB device in FAT 16/32 standard
Unit powers off by itself
Unit takes about 45 seconds to recognize some USB device or
SD card
The battery may be too low (the unit operating voltage is 10.8v to
15.6v).
This is normal. The unit sometimes takes longer time to read all the files inside the USB device or SD Card.
Operations keys do not work
The unit picks up engine noise.
The radio does not work. The radio station automatic selection does not work
The antenna cable is not connected or the signals are too weak
SiriusXM® Troubleshooting
Recommended Description Advisory
Name
Check
Antenna
Try to remove the USB device or memory card and insert it again.
Press the RESET button
Check the ground wire.
Insert the antenna cable firmly or select a station manually
The radio has detected a fault with the SiriusXM antenna.
The antenna cable may be either disconnected or damaged. Verify that the antenna cable is connected to the
27
Check
Tuner
No
Signal
Subscription
Updated
Channel
Not
Available
Channel
Not
Subscribed
Channel
Locked
SiriusXM Connect Vehicle Tuner. Inspect the antenna cable for damage and kinks. Replace the antenna if the cable is damaged. SiriusXM products are available at your local car audio retailer or online at www.shop.siriusxm.com
.
The radio is having difficulty communicating with the
SiriusXM Connect Vehicle Tuner. The tuner may be disconnected or damaged. Verify that the SiriusXM
Connect Vehicle Tuner cable is securely connected to the radio
The SiriusXM Connect Vehicle Tuner is having difficulty receiving the SiriusXM satellite signal. Verify that your vehicle is outdoors with a clear view of the sky. Verify that the SiriusXM magnetic mount antenna is mounted on a metal surface on the outside the vehicle. Move the
SiriusXM antenna away from any obstructions. Inspect the antenna cable for damage and kinks. Consult the SiriusXM
Connect Vehicle tuner installation manual for more information on antenna installation. Replace the antenna if the cable is damaged. SiriusXM products are available at your local car audio retailer or online at www.shop.siriusxm.com
.
The radio has detected a change in your SiriusXM subscription status. Visit www.siriusxm.com or call 866--
635--
‐
2349 if you have questions about your subscription.
The channel that you have requested is not a valid
SiriusXM channel or the channel that you were listening to is no longer available. You may also see this message briefly when first connecting a new SiriusXM Connect
Vehicle tuner. Visit www.siriusxm.com for more information about the SiriusXM channel lineup.
The channel that you have requested is not included in your
SiriusXM subscription package or the channel that you were listening to is no longer included in your SiriusXM subscription package. Visit www.siriusxm.com or call 866--
‐ 635-‐ 2349 if you have questions about your subscription package or would like to subscribe to this channel.
The channel that you have requested is Locked by the radio Parental Control feature. See Parental Control, page
20 for more information on the Parental Control feature and how to access locked channels.
28
T E C H N I C A L S P E C I F I C A T I O N S
TUNER(AM)
Frequency Range
Usable Sensitivity
TUNER(FM)
Frequency Range
Channel Step
Sensitivity
Stereo Separation
Signal to Noise Ratio
LINE-OUT
Output
Impedance
GENERAL
Power Supply
530-1710 KHz
32 dBuV
87.5-107.9 MHz
200KHz
2.8 uV
30dB
50dB
5 Volt ( max )
33 Ohm
12V DC (10.8-15.6V allowable)
Speaker Impedance
Output Power
4 or 8 ohm
45W x 4CH
Fuse 15A
NOTE: Specification & design subject to change without notice for improvements.
29
W A R R A N T Y I N F O R M A T I O N
This unit is warranted to be free of defects in material and workmanship for a period of two years. Warranty is subject to proper installation and operation within the published specifications. Except as provided below,
Poly-Planar will repair or replace, at its discretion, any unit returned prepaid to our facility with proper documentation and determined to be defective in normal use. Poly-Planar is not liable for any consequential damages.
LIMITS OF LIABILITY
Proof of date of purchase is required for warranty service of this unit.
Poly-Planar will consider this warranty void if unit has been tampered with or has had serial number altered, defaced or removed. Poly-Planar warranty does not cover damage incurred in transit, accident, abuse, misuse, negligence, fire, flood, lightning, or unauthorized service. This warranty assumes no responsibility for damages incurred during installation of this equipment. This warranty does not cover labor costs for removal of defective unit or reinstallation of replacement unit. This warranty covers normal consumer use only. In no event shall Poly-Planar be liable for special, incidental, or consequential damages.
To obtain service under this warranty, please call Poly-Planar for a
RETURN AUTHORIZATION NUMBER . After a return authorization number is issued, return unit with proof of purchase and a letter stating your return address, daytime phone number and detail description of the problem or malfunction
poly-planar
Maryland, USA
(410) 761-4000 www.polyplanar.com
30
NOTES:
31
32
33
advertisement
Related manuals
advertisement