L.O.C.PRO™ LP7-2

Line Output Converter

The professional way to integrate your new amplifier or radio.

Installation Instructions

Before You Start

Replacing your radio? PAC also produces RadioPRO ™ which is a radio replacement solution, with steering wheel control retention built-in. This greatly expedites the installation of a new radio into your vehicle.

To see if there is a RadioPRO ™ interface for your vehicle, visit www.pac-audio.com

and search "Radio PRO".

Install It Right with L.O.C. PRO

™

Don’t cheat yourself out of all the performance your new radio or amplifier can deliver. Proper audio line level matching is critical when replacing your vehicle’s factory (OEM) radio or amplifier. It can be the difference between a great sounding system that you enjoy every day and a buggy, noisy mess that drives you crazy.

PAC L.O.C.PRO™ interfaces have been professionally designed for those who want the very best.

General Overview

The L.O.C.PRO™ LP7-2 can be used for either replacing an OEM radio and retaining the factory amplified system or adding amplifiers to a system that does not have RCA outputs. L.O.C.PRO™ LP7-2 will also monitor the audio input signal and automatically create an amplifier remote turn-on for systems that do not have one. Level matching is achieved using precision stereo gain dials and will enable proper adjustment of audio output of the radio for optimum system performance. Differential inputs also allow for use in OEM BOSE and other premium system scenarios. Included in these instructions are the most common applications for the

L.O.C.PRO™ LP7-2. For specialty applications not covered in this manual, please visit www.pac-audio.com

for more comprehensive, vehicle specific wiring diagrams. Direct url - www.pac-audio.com/products/locpro

Speaker Level Input to RCA Level Output

Speaker level input to RCA level output is the most commonly used configuration for the LP7-2.

Use this when you need to create RCA level outputs from a source that only has speaker level outputs.

The RCA input connectors on the main harness will not be utilized for this type of installation, we suggest cutting them off the harness 3 inches from the RCA end so they can be saved and used for a future installation.

After all the connections are made on the remaining wires, skip to the level adjustment section of this manual.

Cut away RCA ends for wired speaker level inputs

Constant 12v + Input

Remote 12v + Output (

500ma

)

Chassis Ground -

Audio Ground Input (

OPTIONAL

)

+ + + + + + + + + + + +

+ + + + + + + + +

Front Left Audio Input

+ + + + + + + + + + + + + + + + + + + + + +

Front Right Audio Input

+ + + + + + + + + + + + + + + + + + + + + + + +

3"

Front Left Output

Front Right Output

Note: If using large RCA connectors that are difficult to insert into housing, unsnap the

L.O.C.PRO™ cover and remove end panel insert around RCA outputs.

Copyright 2013 Pacific Accessory Corporation. Content subject to change without notice.

1

Speaker Level Input to Speaker Level Output

Speaker level input to speaker level output is most commonly used when replacing an OEM radio and retaining the factory installed amplifiers.

Use this when you need to match levels from a source that only has speaker level outputs and an amplifier with speaker level inputs. The RCA input connectors on the main harness will be used for this type of installation, we suggest cutting them off the harness 3 inches from the RCA end so they can be used for the wired speaker level output. After all the connections are made, skip to the level adjustment section of this manual.

Cut RCA in half from main harness. Then connect to ouputs of L.O.C to provide wired speaker lead outputs.

Constant 12v + Input

Remote 12v + Output (

500ma

) Front Left Output

+ + + + + + + + + + + + + + + + + + + + + + +

Chassis Ground -

Audio Ground Input (

OPTIONAL

)

+ + + + + + + + + + + +

+ + + + + + + + +

Front Left Audio Input

+ + + + + + + + + + + + + + + + + + + + + +

Front Right Audio Input

+ + + + + + + + + + + + + + + + + + + + + + + +

3"

Front Right Output

+ + + + + + + + + + + + + + + + + + + + + + +

Level Adjustment

New School –

Required items: Digital Multi-Meter, Test track media @ 1kHz and 100Hz. Max Amplifier Line-level Input Voltage Specification (i.e., 4vrms, 8vrms, etc.)

Proper level adjustment is crucial for obtaining the best possible sound quality. Following the guidelines below will enable you to properly set the output gain of the LP7-2 using equipment that is readily available. Although this device can be set by ear (Old School), we recommend using a multimeter and test tracks for pinpoint accuracy and the least chance of noise.

Amplifiers usually have 2, 4 or 8v max line-level input ratings but this can vary. This max line-level input will be your target setting you will read on the multi-meter. Perform the following procedure for each amplifier you are installing.

Example:

Amplifier 1 (Mid/High frequency) has a maximum 4v input voltage, so you will be targeting a 4 volt output voltage from the LP7-2.

or

Amplifier 1 (Sub frequency) has a maximum 2v input voltage, so you will be targeting a 2 volt output voltage from the LP7-2.

1. Start with gain adjustment levels on LP7-2 and amplifiers set to minimum.

2. Turn source unit to ¾ maximum volume and start test track

(1kHz for mid/high or full range, 100Hz for sub).

3. Choose either left or right channel - With multi-meter, test output of LP7-2 .

Probe with negative on RCA shield and positive in center of RCA output. (figure 1)

4. Slowly adjust level on LP7-2 until you reach the target voltage of the amplifier. (figure 2)

5. Turn volume down and system off.

6. Connect RCAs, set gains on amplifiers to minimum

7. Turn system on and fine tune gains of amplifier (if needed).

Old School –

1. Start with gain adjustment levels on LP7-2 and amplifiers set to minimum.

2. Turn source unit to ¾ maximum volume and play a familiar song that has dynamic attributes.

For example, if your volume goes to 40 you will turn it up to 30 and play a song that has some quiet sections and some really loud sections.

3. Slowly adjust front channel gain of LP7-2 until just a hint of distortion is audible, and then back down gain just under that threshold and the distortion goes away. (figure 2)

Figure 1

Set meter to AC voltage.

Connect Red probe to Voltage (V)

Black to Common (COM)

Figure 2

_

+

2

Pacific Accessory Corporation

Santa Ana, CA 92705 [email protected] • www.pac-audio.com

Copyright 2013 Pacific Accessory Corporation. Content subject to change without notice.