ANI-5PLAY

TM

HDMI + LAN Extender PoH CAT5e/CAT6 HDBaseT

™

A-NeuVideo.com

Frisco, Texas 75034

(317) 456-2461

AUDIO / VIDEO MANUFACTURER

SAFETY INFORMATION

1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.

Retain all documentation for future reference.

2. Follow all instructions printed on unit chassis for proper operation.

3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.

4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and excessive moisture.

5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.

6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.

7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.

8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated.

9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by any warranty.

10. Turn power off and disconnect unit from AC current before making connections.

11. Never hold a power switch in the “ON” position.

12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.

13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter.

14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to qualified service personnel. There are no user serviceable parts inside.

15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to other devices.

16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.

17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.

18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing.

19. Service Information Equipment should be serviced by qualified service personnel when:

A. The power supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the equipment.

C. The equipment has been exposed to rain.

D. The equipment does not appear to operate normally, or exhibits a marked change in performance.

E. The equipment has been dropped, or the enclosure damaged.

THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

A NEU VIDEO

TABLE OF CONTENTS

CONTENTS

INTRODUCTION.............................................................1

PACKAGE CONTENTS .................................................................1

FEATURES ................................................................................... 2

SPECIFICATIONS ........................................................................ 2

UTP CABLE TERMINATION ...................................................... 3

OPERATION CONTROLS & FUNCTIONS .................................. 4

TRANSMITTER ...................................................................... 4

RECEIVER ............................................................................ 5

DESCRIPTIONS ........................................................................... 6

APPLICATION EXAMPLE ........................................................... 8

IR DESCRIPTION ........................................................................ 9

DEAR CUSTOMER

Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this equipment:

• Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.

• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the

PSU if it is damaged.

• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.

INTRODUCTION

The ANI-5PLAY ™ is a HDMI extender tool which can extend your

HDMI signal up to 328 ft (100M) to a compatible display. It is designed to convert HDMI signals to standard HDBaseT ™ signals which can be transmitted by a single CATx cable. It also supports bi-directional infrared control signals, RS-232 control signals and an ethernet signal together with an uncompressed HDMI signal. The

ANI-5PLAY ™ also supports PoH (Power over HDBaseT the Receiver. The ANI-5PLAY has a 3 year warranty.

™

™ ) requiring only one power supply to provide power to both the Transmitter and

also supports 4K2K! This product

DISCLAIMERS

The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for any infringements of patents or other rights of third parties which may result from its use.

We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update or to keep current the information contained in this document.

We reserve the right to make improvements to this document and/ or product at any time and without notice.

PACKAGE CONTENTS

Before attempting to use this unit, please check the packaging and make sure the following items are contained in the shipping carton:

• HDMI Extender Transmitter

• HDMI Extender Receiver

• (2) Wideband IR Tx

• (2) Wideband IR Rx

• (2) Phoenix male jack

• Power Supply Adapter: AC100-240V 50/60Hz / DC 24V@1A

• Users Guide

COPYRIGHT NOTICE

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means

— electronic, mechanical, magnetic, optical, chemical, manual, or otherwise — without the express written permission and consent.

© Copyright 2016. All Rights Reserved.

Version 2.3 AUG 2016

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

1

A NEU VIDEO

FEATURES & SPECIFICATIONS

FEATURES

• PoH (Power over HDBaseT ™ ) function supports, either the TX or the RX, powered with the 24V@1A power supply, the other does not need power from the DC jack. PoH power consumption is less than 10W

• Uses a single UTP LAN cable (CAT5e/6) to substitute the HDMI cable to achieve long distance transmission

• UTP cable termination follows the IEEE-568A or IEEE-568B standards

• Transmission Distance:

• 328 ft/100M: 1080p@60Hz@36bit / 3D1080p@30Hz@36bit

• 230 ft/70M: 1080p@60Hz@48bit / 1080p@120Hz@24bit / 3D1080p@60Hz@36bit / 4K2K@30Hz@24bit

• Supports display resolutions up to 4K2K@30Hz

• Full HD Support: 1080p@60Hz@48bit/pixels / 1080p@120Hz@24 bit/pixels / 3D-1080p@60Hz and 4K2K@30Hz@24bit

• Transfers bi-directional infrared control signals together with the HDMI signal

• Transfers bi-directional RS-232 control signals together with the HDMI signal

• Transfers bi-directional Ethernet signals together with the HDMI signal

Specifications

• Frequency Bandwidth: 2.97Gbps

• Transmitter Input/Output Ports:

• (1) HDMI female port / (2) CAT6

• (1) IR Tx / (1) IR Rx / (1) Phoenix

• Receiver Input/Output Ports:

• (1) HDMI female port / (2) CAT6

• (1) IR Tx / (1) IR Rx / (1) Phoenix

• ESD Protection: ±8kV (air-gap discharge)

• Human Body Model: ±4kV (contact discharge)

• Dimensions (WxDxH): 4 x 4 x 1 in (100x100x25mm)

• Weight: 0.7 lb (Unit only) / 2.2 lb (Net)

• Operating Temperature: 0°C ~ 40°C / 32°F ~ 104°F

• Storage Temperature : -20°C ~ 60°C / -4°F ~ 140°F

• Relative Humidity: 20~90% RH (Non-condensing)

• Power Consumption (Max): 10W

• Power Supply: DC 24V@1A

As product improvements are continuous, specifications are subject to change without notice.

2

A NEU VIDEO

UTP CABLE TERMINATION

UTP cable termination

The extender uses a UTP cable termination following IEEE-568A and IEEE-568B standards.

CABLE

CAT6

CAT6

CAT5e

CAT5e

LENGTH RESOLUTION

230 ft/70M 4K

328 ft/100M 1080p

131 ft/40M 4K

328 ft/100M 1080p

Direct Interconnection Method

Cross Interconnection Method

3

A NEU VIDEO

Transmitter

OPERATION CONTROLS AND FUNCTIONS

q INPUT LED: Input status indicating lamp. This red LED illuminates when the HDMI signal is plugged in.

w HDMI IN: HDMI input port. This slot is where you connect the HDMI source.

e ETHERNET: This slot provides internet signal from the receiver or to the receiver.

r RS-232: Phoenix jack provides Serial port control from the receiver or to the receiver.

t DC IN: Plug the 24V DC power supply into the unit.

y IR RX: Chanel 1 IR Receiver. Connects with the Wideband IR Rx.

u IR TX: Chanel 2 IR Transmitter. Connects with the Wideband IR Tx.

i LINK LED: Connection status indicating lamp.

• Illuminated: The Transmitter and Receiver have good connections.

• Flashing: The Transmitter and Receiver have poor connections.

• Dark: The Transmitter and Receiver are not connected.

o HDBaseT ™ OUT: HDBaseT ™ signal output port. Connects the HDBaseT ™ receiver with a UTP cable following IEEE-568A or IEEE-

568B standards. a DATA LED: Data status indicating lamp.

• Illuminated: The HDMI signal has HDCP.

• Flashing: The HDMI signal is without HDCP.

• Dark: No HDMI signal.

4

A NEU VIDEO

RECEIVER

OPERATION CONTROLS AND FUNCTIONS

q OUTPUT LED: Output status indicating lamp. This red LED illuminates when the TV is connected to a HDMI cable.

w HDMI OUT: HDMI output port. This slot is where you connect the HDTV or monitor with a HDMI cable.

e ETHERNET: This slot provides internet signal from the transmitter or to the transmitter.

r RS-232: Phoenix jack provides Serial port control from the transmitter or to the transmitter.

t DC IN: Plugs the 24V DC power supply into the unit.

y IR RX: Chanel 2 IR Receiver. Connects with the Wideband IR Rx.

u IR TX: Chanel 1 IR Transmitter. Connects with the Wideband IR Tx.

i LINK LED: The connection status indicating lamp.

• Illuminated: The Transmitter and Receiver have good connections.

• Flashing: The Transmitter and Receiver have poor connections.

• Dark: The Transmitter and Receiver are not connected.

o HDBaseT ™ IN: HDBaseT ™ signal input port. Connects the HDBaseT ™ transmitter with a UTP cable following IEEE-568A or IEEE-568B standards. a DATA LED: Data status indicating lamp.

• Illuminated: The HDMI signal has HDCP.

• Flashing: The HDMI signal is without HDCP.

• Dark: No HDMI signal.

5

A NEU VIDEO

Description

1

PoH (Power over HDBaseT ™ ) Application Example.

Descriptions

Description 2

Bi-directional Infrared Control Application Example.

6

A NEU VIDEO

Description 3

Bi-directional RS-232 Control Application Example.

Descriptions

Description 4

Bi-directional Ethernet Signal Application Example.

7

A NEU VIDEO

Application Example

Application Example

8

A NEU VIDEO

ir DESCRIPTION ir DESCRIPTION

9

A NEU VIDEO

TERMS AND CONDITIONS OF USE

PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED

BY, THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc. at the return address set forth on the Product’s packing label at your expense. A-NeuVideo, Inc. may modify these Terms and Conditions at anytime, without notice to you.

RESTRICTIONS ON USE OF THE PRODUCT

It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.

You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be borne by you and you agree to indemnify and hold harmless A-NeuVideo, Inc. from and against any such damage.

The Product is protected by certain intellectual property rights owned by or licensed to A-NeuVideo. Any intellectual property rights pertaining to the Product are licensed to you by A-NeuVideo, Inc. and/or its affiliates, including any manufacturers or distributors of the Product (collectively, “A-NeuVideo”) for your personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.

The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by A-NeuVideo for your personal use only.

A-NeuVideo does not transfer either the title or the intellectual property rights to the Product and A-NeuVideo retains full and complete title to the intellectual property rights therein. All trademarks and logos are owned by A-NeuVideo or its licensors and providers of the Product, and you may not copy or use them in any manner without the prior written consent of A-NeuVideo, which consent may be withheld at the sole discretion of A-NeuVideo.

The functionality and usability of the Product is controlled by A-NeuVideo, Inc. from its offices within the State of Texas, United States of America. A-NeuVideo makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided with respect thereto. You are advised that the Product may be subject to U.S. export controls.

DISCLAIMERS AND LIMITATION OF LIABILITY

A-NeuVideo may change or modify the Product at any time, from time to time.

THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. A-NEUVIDEO DOES NOT WARRANT OR

MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,

OR OTHERWISE.

A-NeuVideo has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.

TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, A-NEUVIDEO DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.

A-NEUVIDEO DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.

A-NEUVIDEO DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO

THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.

A-NEUVIDEO WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT

TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT A-NEUVIDEO) ASSUME THE ENTIRE COST OF ALL

NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY

A-NEUVIDEO.

UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL A-NEUVIDEO BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL

DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF

A-NEUVIDEO OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL A-NEUVIDEO’S TOTAL

LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU

PAID TO A-NEUVIDEO, IF ANY, FOR THE PRODUCT.

END OF DOCUMENT

10