Eurocom Panther 3.0 User Guide Manual

Add to my manuals
284 Pages

advertisement

Eurocom Panther 3.0 User Guide Manual | Manualzz

Downloaded from LpManual.com Manuals

V11.6.00

Downloaded from LpManual.com Manuals

Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.

This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes.

Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer.

©June 2011

Trademarks

Intel and Intel Core are trademarks/registered trademarks of Intel Corporation.

Downloaded from LpManual.com Manuals

I

Preface

R&TTE Directive

This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC.

This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland,

United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.

CE Marking

This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.

This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE

Marking. A notified body has determined that this device has properly demonstrated that the requirements of the directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the notified body number 0560 after the CE mark.

The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product.

Secondly, CE Marking is mandatory for the product it applies to, whereas most quality markings are voluntary.

Preface

FCC Statement

(Federal Communications Commission)

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the service representative or an experienced radio/TV technician for help.

Operation is subject to the following two conditions:

1.

This device may not cause interference.

And

2.

This device must accept any interference, including interference that may cause undesired operation of the device.

Downloaded from LpManual.com Manuals

III

Preface

FCC RF Radiation Exposure Statement:

1.

This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Warning

Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standards could void your authority to operate the equipment.

Preface

IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment:

1.

Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

2.

Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning.

3.

Do not use the telephone to report a gas leak in the vicinity of the leak.

4.

Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.

5.

This product is intended to be supplied by a Listed Power Unit (Full Range AC/DC Adapter - AC Input 100 -

240V, 50 - 60Hz DC Output 20V, 15A (300W) minimum).

This Computer’s Optical Device is a Laser Class 1 Product

Downloaded from LpManual.com Manuals

V

Preface

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1.

Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.

Do not expose the computer to any shock or vibration.

Do not place it on an unstable surface.

Do not place anything heavy on the computer.

2.

Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.

Do not expose it to excessive heat or direct sunlight.

Do not leave it in a place where foreign matter or moisture may affect the system.

Don’t use or store the computer in a humid environment.

Do not place the computer on any surface that will block the

Vents/Fan Intakes.

Preface

3.

Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data.

4.

Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.

Do not turn off the power until you properly shut down all programs.

Do not turn off any peripheral devices when the computer is on.

Do not disassemble the computer by yourself.

Perform routine maintenance on your computer.

5.

Take care when using peripheral devices.

Use only approved brands of peripherals.

Unplug the power cord before attaching peripheral devices.

Downloaded from LpManual.com Manuals

VII

Preface

Power Safety

The computer has specific power requirements:

Power Safety

Warning

Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on.

• Only use a power adapter approved for use with this computer.

• Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.

• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.

• When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire.

• Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.

• Before cleaning the computer, make sure it is disconnected from any external power supplies (i.e. AC/DC adapter or car adapter).

Do not plug in the power cord if you are wet.

Do not use the power cord if it is broken.

Do not place heavy objects on the power cord.

Preface

Polymer Battery Precautions

Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf.

• Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern.

• Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient temperature environments, and do not store unused batteries for extended periods.

See also the general battery precautionary information overleaf for further information.

Downloaded from LpManual.com Manuals

IX

Preface

General Battery Precautions

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.

• Do not remove any batteries from the computer while it is powered on.

• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.

• If you do not use the battery for an extended period, then remove the battery from the computer for storage.

• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qualified service personnel.

• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode or leak if exposed to fire, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Affix tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.

Battery Disposal & Caution

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.

Preface

Cleaning

Do not apply cleaner directly to the computer; use a soft clean cloth.

Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Servicing

Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:

• When the power cord or AC/DC adapter is damaged or frayed.

• If the computer has been exposed to rain or other liquids.

• If the computer does not work normally when you follow the operating instructions.

• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).

• If there is an unusual odor, heat or smoke coming from your computer.

Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before turning the computer on.

Downloaded from LpManual.com Manuals

XI

Preface

Travel Considerations

Packing

As you get ready for your trip, run through this list to make sure the system is ready to go:

1.

Check that the battery pack and any spares are fully charged.

2.

Power off the computer and peripherals.

3.

Close the display panel and make sure it’s latched.

4.

Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.

5.

The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter. However, check with your travel agent to see if you need any socket adapters.

6.

Put the notebook in its carrying bag and secure it with the bag’s straps.

7.

If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters and/or cables.

8.

Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both hardware and software. Make sure your “papers” are handy.

Power Off Before Traveling

Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.

Preface

On the Road

In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:

Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.

Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:

Some airports also scan luggage with these devices.

Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.

These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.

Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged.

Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.

Wait a few minutes before turning it on so that any moisture can evaporate.

Downloaded from LpManual.com Manuals

XIII

Preface

Developing Good Work Habits

Developing good work habits is important if you need to work in front of the computer for long periods of time.

Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain:

• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.

• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on a footrest if necessary.

• Use a chair with a back and adjust it to support your lower back comfortably.

• Sit straight so that your knees, hips and elbows form approximately 90-degree angles when you are working.

• Take periodic breaks if you are using the computer for long periods of time.

Remember to:

• Alter your posture frequently.

• Stretch and exercise your body several times a day.

• Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.

Preface

Lighting

Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue.

• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.

• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.

• Position the display directly in front of you at a comfortable viewing distance.

• Adjust the display-viewing angle to find the best position.

LCD Screen Care

To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for an extended period of time) take the following precautions:

• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.

• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).

• Rotate desktop background images every few days.

• Turn the monitor off when the system is not in use.

Cable TV Safety

If you have included a TV Tuner in your purchase option then pay careful attention to the following:

• Make sure that your CATV system installer has connected the Coaxial cable shield to the grounding system of the building, as close to the point of cable entry as practical.

• This reminder is provided to call the CATV system installer’s attention to Article 820-93 of the NEC (Section 54, Part

I of the Canadian Electrical Code).

• The TV antenna supplied with any TV Tuner module is intended for indoor use only. Please do not use your TV Tuner module outdoors.

Downloaded from LpManual.com Manuals

XV

Preface

LCD Electro-Plated Logos

Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive.

Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during transport. If any such wear and tear develops contact your service center.

Preface

Contents

Notice ................................................................................. I

FCC Statement ................................................................ III

FCC RF Radiation Exposure Statement: ........................ IV

Instructions for Care and Operation ............................... VI

Power Safety ................................................................ VIII

Polymer Battery Precautions .......................................... IX

General Battery Precautions ............................................ X

Cleaning .......................................................................... XI

Servicing ......................................................................... XI

Travel Considerations ....................................................XII

Keyboard ........................................................................1-9

Function Keys & Visual Indicators .............................1-10

System Map: Front & Rear Views ...............................1-11

System Map: Right View .............................................1-12

System Map: Left View ...............................................1-13

System Map: Bottom View ..........................................1-15

Windows 7 Start Menu & Control Panel .....................1-16

Video Features .............................................................1-17

Screen Resolution ........................................................1-18

NVIDIA Control Panel ................................................1-19

Catalyst Control Center ...............................................1-20

Power Options ..............................................................1-21

Quick Start Guide

Overview ........................................................................ 1-1

Advanced Users ............................................................. 1-2

Beginners and Not-So-Advanced Users ........................ 1-2

Warning Boxes .............................................................. 1-2

Not Included .................................................................. 1-3

System Software ............................................................ 1-4

RAID & AHCI Setup ..................................................... 1-4

System Startup ............................................................... 1-5

System Map: LCD Panel Open & Top View ................ 1-6

LED Indicators ............................................................... 1-7

Touch Sensor Instant Keys ............................................ 1-8

Storage Devices, Mouse, Audio &

Printer

Overview ........................................................................2-1

Hard Disk Drive .............................................................2-2

Optical Device ...............................................................2-3

Loading Discs ................................................................2-3

Handling CDs or DVDs .................................................2-4

DVD Regional Codes ....................................................2-5

Multi-In-1 Card Reader .................................................2-6

ExpressCard Slot ............................................................2-7

Downloaded from LpManual.com Manuals

XVII

Preface

Inserting and Removing ExpressCards .......................... 2-7

Audio Features ............................................................... 2-8

Setup for Audio Recording ............................................ 2-9

Setup for 5.1 or 7.1 Surround Sound ...........................2-10

Dolby Settings ............................................................. 2-12

HDMI Audio Configuration ........................................ 2-13

Audio Setup for LCD Monitors/

TVs with HDMI Input ................................................. 2-14

TouchPad and Buttons/Mouse ..................................... 2-16

Gestures and Device Settings ......................................2-18

Adding a Printer ...........................................................2-21

USB Printer ..................................................................2-21

Install Instructions: ......................................................2-21

Parallel Printer ............................................................. 2-21

Power Management

Overview ........................................................................ 3-1

The Power Sources ........................................................ 3-2

AC/DC Adapter ............................................................. 3-2

Battery ............................................................................ 3-2

Turning On the Computer .............................................. 3-3

Power Plans ................................................................... 3-4

Power-Saving States ...................................................... 3-6

Sleep .............................................................................. 3-6

Hibernate ........................................................................ 3-7

Shut down ......................................................................3-7

Configuring the Power Buttons .....................................3-8

Resuming Operation ......................................................3-9

Battery Information ......................................................3-10

Conserving Battery Power ...........................................3-11

Battery Life ..................................................................3-12

New Battery .................................................................3-12

Recharging the Battery with the AC/DC Adapter .......3-12

Proper handling of the Battery Pack ............................3-13

Battery FAQ .................................................................3-14

Drivers & Utilities

RAID & AHCI Setup .....................................................4-1

What to Install ................................................................4-1

Module Driver Installation .............................................4-1

Driver Installation ..........................................................4-2

Manual Driver Installation .............................................4-4

Updating/Reinstalling Individual Drivers ......................4-4

User Account Control ....................................................4-5

Windows Security Message ...........................................4-5

New Hardware Found ....................................................4-5

Driver Installation Procedure .........................................4-6

Chipset ...........................................................................4-7

Video (NVIDIA) ............................................................4-7

Video (AMD) .................................................................4-7

Preface

LAN ............................................................................... 4-7

Card Reader ................................................................... 4-7

TouchPad ....................................................................... 4-8

USB 3.0 .......................................................................... 4-8

Hot Key .......................................................................... 4-8

Audio ............................................................................. 4-8

Windows Experience Index ........................................... 4-9

Optional Drivers ..........................................................4-10

Wireless LAN ..............................................................4-10

PC Camera ................................................................... 4-11

Consumer Infrared (for TV Tuner Remote) ................4-11

Security Modules (Fingerprint & TPM) ...................... 4-11

BIOS Utilities

Overview ........................................................................ 5-1

The Power-On Self Test (POST) ................................... 5-2

Failing the POST ........................................................... 5-3

Fatal Errors .................................................................... 5-3

Non-Fatal Errors ............................................................ 5-3

The Setup Utility ............................................................ 5-4

Entering Setup ............................................................... 5-4

Setup Screens ................................................................. 5-5

Main Menu ..................................................................... 5-6

System Time & Date (Main Menu) ............................... 5-6

System/Extended Memory: (Main Menu) ..................... 5-7

BIOS Revision/VGA Card etc. (Main Menu) ...............5-7

Advanced Menu .............................................................5-8

Advanced Chipset Control (Advanced Menu) ...............5-8

SATA Mode Selection (Advanced Menu) .....................5-9

Legacy USB Support: (Advanced Menu) ......................5-9

Boot-time Diagnostic Screen: (Advanced Menu) ..........5-9

Reset Configuration Data (Advanced Menu) ................5-9

Power On Boot Beep (Advanced Menu) .....................5-10

Battery Low Alarm Beep: (Advanced Menu) ..............5-10

Advanced Chipset Control Menu ................................5-11

Bluetooth Power Setting >

Advanced Chipset Control ...........................................5-11

Intel Virtualization Technology >

Advanced Chipset Control ...........................................5-12

Hyperthreading > Advanced Chipset Control .............5-12

CPU C State > Advanced Chipset Control ..................5-12

Turbo Boost > Advanced Chipset Control ..................5-12

Security Menu ..............................................................5-13

Set Supervisor Password (Security Menu) ..................5-13

Set User Password (Security Menu) ............................5-14

Password on boot (Security Menu) ..............................5-14

TPM State ....................................................................5-15

Change TPM State (TPM State) ..................................5-15

Boot Menu ...................................................................5-17

Exit Menu ....................................................................5-18

Downloaded from LpManual.com Manuals

XIX

Preface

Upgrading The Computer

Overview ........................................................................ 6-1

When Not to Upgrade .................................................... 6-2

Removing the Battery .................................................... 6-3

Upgrading the Hard Disk Drive(s) ................................ 6-4

Upgrading the Optical (CD/DVD) Device .................. 6-13

Upgrading the System Memory (RAM) ...................... 6-14

Modules

Overview ........................................................................ 7-1

Setting Up SATA RAID Mode ...................................... 7-2

AHCI Mode ................................................................... 7-2

RAID .............................................................................. 7-2

Intel® Rapid Storage Technology Application ............. 7-2

SATA RAID Setup Procedure (BIOS) .......................... 7-4

RAID Setup (Intel Matrix) ............................................. 7-5

Intel Rapid Storage Technology .................................... 7-8

IRST Driver Installation ................................................ 7-8

RAID Volume Data Verification and Repair .............. 7-10

Replacing and Reverting Recovery and

Master Volumes ...........................................................7-10

RAID Volume Data Verification and Repair .............. 7-12

Replacing and Reverting Recovery and

Master Volumes ...........................................................7-12

Wireless LAN Module ................................................. 7-15

Intel® Wi-Fi Link Series Driver Installation ...............7-16

802.11b/g/n Driver Installation ....................................7-16

Connecting to a Wireless Network in Windows 7 .......7-17

Intel® My WiFi Configuration ....................................7-20

Windows Mobility Center ...........................................7-32

PC Camera Module ......................................................7-33

PC Camera Driver Installation .....................................7-34

PC Camera Audio Setup ..............................................7-35

TV Tuner Module ........................................................7-41

Consumer Infrared Driver ............................................7-42

Digital TV Broadcast Signal ........................................7-43

TV Recording and Power Plans ...................................7-43

Remote Control Unit ....................................................7-43

Bluetooth Module ........................................................7-44

3rd Party Bluetooth Combo Driver Installation ...........7-46

3rd Party Bluetooth & WLAN Combo Settings ..........7-47

Bluetooth Networking Setup .......................................7-50

Bluetooth & WLAN Combo Module Configuration ...7-51

Intel Bluetooth Combo Driver Installation ..................7-54

Bluetooth Configuration in Windows 7 .......................7-55

Security Modules (Fingerprint & TPM) ......................7-59

Fingerprint Reader Module ..........................................7-60

Fingerprint Reader Driver Installation .........................7-60

User Enrollment ...........................................................7-61

Fingerprint Control Center Features ............................7-64

Preface

Trusted Platform Module ............................................. 7-65

Enabling & Activating TPM ........................................ 7-65

Trusted Platform Module (TPM) Driver Installation .. 7-67

Initializing TPM ...........................................................7-67

Infineon Security Platform Settings Tool ....................7-70

Troubleshooting

Overview ........................................................................ 8-1

Basic Hints and Tips ...................................................... 8-2

Backup and General Maintenance ................................. 8-3

Viruses ........................................................................... 8-4

Upgrading and Adding New Hardware/Software .......... 8-5

Problems & Possible Solutions ...................................... 8-7

Bluetooth Connection Problems .................................. 8-15

Intel® WLAN & Bluetooth V3.0+HS

Combo Modules ...........................................................8-19

Interface (Ports & Jacks)

Overview ....................................................................... A-1

Ports and Jacks .............................................................. A-2

Card Reader .................................................................. A-2

Cable (CATV) .............................................................. A-2

Antenna Jack ................................................................. A-2

Consumer Infrared Transceiver .................................... A-2

DC-In Jack .................................................................... A-2

DVI-Out Port ................................................................ A-2

e-SATA Port ................................................................. A-3

HDMI-Out Port ............................................................. A-3

Headphone-Out Jack ..................................................... A-3

Line-In Jack .................................................................. A-3

Microphone-In Jack ...................................................... A-3

Mini-IEEE 1394b Port .................................................. A-4

RJ-45 LAN Jack ............................................................ A-4

S/PDIF-Out Jack ........................................................... A-4

Security Lock Slot ........................................................ A-4

USB 2.0/1.1 Ports ......................................................... A-5

USB 3.0 Port ................................................................. A-5

NVIDIA Video Driver Controls

NVIDIA Video Driver Installation ...............................B-1

NVIDIA Control Panel (Win 7) ....................................B-2

Display Devices ............................................................B-5

Display Modes ..............................................................B-6

Attaching Other Displays (Win 7) ..............................B-11

SLI Multi GPU Configuration ....................................B-14

SLI Multi GPU Configuration & Battery Power ........ B-15

Enabling TV Display ..................................................B-16

Downloaded from LpManual.com Manuals

XXI

Preface

AMD Video Driver Controls

Video Driver Installation .............................................. C-1

Video (VGA) C-1

Catalyst™ Control Center ............................................ C-2

Catalyst™ Control Center Preferences C-3

Display Devices & Options .......................................... C-7

Configuring an External Display In the CCC ............... C-8

Configuring an External Display In Windows 7 ....... C-12

HDMI Audio Configuration ....................................... C-17

Specifications

Processor ....................................................................... D-2

Core Logic .................................................................... D-2

Display .......................................................................... D-2

Memory ......................................................................... D-2

Video Adapter Options ................................................. D-2

Video Adapter Options ................................................. D-2

Video Adapter Options ................................................. D-3

Video Adapter Options ................................................. D-3

Video Adapter Options ................................................. D-3

BIOS ............................................................................. D-3

Storage .......................................................................... D-4

Audio ............................................................................ D-4

Keyboard & Pointing Device ........................................ D-4

Slots .............................................................................. D-4

Card Reader ..................................................................D-4

Interface ........................................................................ D-4

Communication .............................................................D-5

Security .........................................................................D-5

Operating System ..........................................................D-5

Power Management ......................................................D-5

Power ............................................................................ D-5

Environmental Spec ......................................................D-5

Physical Dimensions & Weight .................................... D-5

Quick Start Guide

Chapter 1: Quick Start Guide

Overview

This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following:

Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,

optical device, card reader), TouchPad & Mouse, Audio Features & Printer.

Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems.

Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).

Chapter 6 Instructions for upgrading your computer.

Chapter 7 A quick guide to the computer’s RAID, Wireless LAN, PC Camera, TV Tuner, Bluetooth &

WLAN Combo and Security (Fingerprint and TPM) modules (some of which may be optional depending on your purchase configuration).

Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external devices.

Appendix B Information on the NVIDIA Video driver controls.

Appendix C Information on the AMD Video driver controls.

Appendix D The computer’s specification.

1

Downloaded from LpManual.com Manuals

Overview 1 - 1

1

Quick Start Guide

Advanced Users

If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to

“Drivers & Utilities” on page 4 - 1

,

“BIOS Utilities” on page 5 - 1

and

“Upgrading The Computer” on page 6 - 1

in the User’s Manual. You may also find the notes marked with a

of interest to you.

Notes

Check the light colored boxes with the mark above to find detailed information about the computer’s features.

Beginners and Not-So-Advanced Users

If you are new to computers (or do not have an advanced knowledge of them) then the information contained in this Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a  as indicated in the margin.

For a more detailed description of any of the interface ports and jacks see

“Interface

(Ports & Jacks)” on page A - 1

.

Warning Boxes

No matter what your level please pay careful attention to the warning and safety information indicated by the

 symbol. Also please note the safety and handling instructions as indicated in the

Preface

.

Quick Start Guide

Not Included

Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.

Drivers

If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order listed in

Table 4 - 1, on page 4

- 3

. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your system hasn’t been properly configured (your service representative may have already done that for you), refer to

“Drivers

& Utilities” on page 4 - 1

for installation instructions.

Ports and Jacks

See

“Ports and Jacks” on page A - 2

for a description of the interface (ports & jacks) which allow your computer to com-

municate with external devices, connect to the internet etc.

1

Downloaded from LpManual.com Manuals

Overview 1 - 3

1

Quick Start Guide

TV Tuner Module

Support

Note that the TV Tuner module (factory) option is supported by the Win-

dows Media Center

software. Windows Me-

dia Center is not included in Starter or Home

Basic versions of Win-

dows 7.

System Software

Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 7 operating system is supported.

Note: In order to run Windows 7 without limitations or decreased performance, your computer requires a minimum 1GB of system memory (RAM).

RAID & AHCI Setup

Note that setting up a RAID, or AHCI mode, needs to be done prior to installing the

Windows OS (see

“Setting Up SATA RAID Mode” on page 7 - 2

).

Quick Start Guide

System Startup

1. Remove all packing materials, and place the computer on a stable surface.

2. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.

3. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.

4. Use one hand to raise the lid/LCD to a comfortable viewing angle (it is preferable not to exceed 135 degrees); use the other hand (as illustrated in

Figure 1 - 1

below) to support the base of the computer (Note: Never lift the computer by the lid/LCD).

5. Raise the lid/LCD to a comfortable viewing angle, and press the power button.

135

1

Shutdown

Note that you should always shut your computer down by choosing the Shut Down command from the Start menu in Windows 7.

This will help prevent hard disk or system problems.

Figure 1 - 1 - Computer with AC/DC Adapter Plugged-In/Opening the Lid/LCD

Downloaded from LpManual.com Manuals

System Startup 1 - 5

1

Quick Start Guide

Figure 1 - 2

LCD Panel Open

& Top View

1. Built-In PC Camera

2. Built-In Microphone

3. LCD

4. LED Status Indicators

5. Touch Sensor Instant

Keys

6. Speakers

7. Power Button

8. Keyboard

9. TouchPad and

Buttons

10. Fingerprint Reader

Module

11. LCD Panel Color

LED

System Map: LCD Panel Open & Top View

6

6

2

5

3

8

1

6

2

6

4

6

7

Wireless Device

Operation Aboard

Aircraft

The use of any portable electronic transmission devices (e.g.

WLAN or Bluetooth) aboard aircraft is usually prohibited. Make sure any wireless modules are

OFF if you are using the computer aboard aircraft.

Use the appropriate function key combination to toggle power to any wireless modules, and check the indicators to see if any modules are powered on or not

(see

Table 1 - 3, on page 1 - 8

).

9

11

10

4

5

5

LED Indicators

The LED indicators display helpful information about the current status of the computer.

Icon Color Description

Icon Color

Blue Scroll Lock is Activated

Blue

Blue

Blinking Blue

Caps Lock is Activated

Number Lock is Activated

Hard Disk Activity

Table 1 - 1 - LED Status Indicators

Quick Start Guide

1

Description

Orange

Green

Blinking

Green

Orange

Blinking

Orange

Green

DC Power is Plugged In

The Computer is On

The Computer is In Sleep Mode

The Battery is Charging

The Battery has Reached

Critically Low Power Status

The Battery is Fully Charged

Table 1 - 2 - LED Power Indicators

Downloaded from LpManual.com Manuals

System Map: LCD Panel Open & Top View 1 - 7

1

Quick Start Guide

Touch Sensor Instant Keys

Press the Touch Sensor Instant Keys on the computer to toggle the appropriate function on/off. When a module is powered on the appropriate icon will be highlighted blue .

Icon Description

Mute Toggle

Bluetooth Module (optional) Power Toggle

Wireless LAN Module (optional) Power Toggle

PC Camera Module Power Toggle

Volume Control (Press and hold your finger at either end to adjust the system volume)

/ of the volume control

Table 1 - 3 - Touch Sensor Instant Keys

Note that you can also use the function key combinations for all of the functions above (see page

1 - 10

).

Quick Start Guide

Keyboard

The keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. See

Table 1 - 4, on page 1 - 10

for full function key combination details.

Function Keys

NumLk &

ScrLk Keys

Play/Pause Key

Numerical

Keypad

Fn Key

Figure 1 - 3 - Keyboard

Special Characters

Some software applications allow the number-keys to be used with Alt to produce special characters.

These special characters can only be produced by using the numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that NumLk is on.

Other Keyboards

If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work.

Num Lk & Scr Lk

Hold down the Fn Key and Scr Lk/Num Lk to enable scroll lock/number lock, and check the LED indicator for status.

1

Downloaded from LpManual.com Manuals

Keyboard 1 - 9

1

Quick Start Guide

Function Keys & Visual Indicators

The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators (see the table below) are available when the Hot Key driver is installed (see

“Hot Key” on page 4 - 8

).

After installing the driver an icon will appear in the taskbar.

Keys

Fn + ~

Fn + F1

Fn + F2

Fn + F3

Fn + F4

Fn +F5/F6

Fn + F7

Function/Visual Indicators

Play/Pause (in Audio/Video Programs)

Touchpad Toggle

Turn LCD Backlight Off

(Press a key to or use Touchpad to turn on)

Mute Toggle

Keys

Fn +F8/F9

Fn + F10

Fn + F11

Fn + F12

Function/Visual Indicators

Brightness Decrease/

Increase

PC Camera Power

Toggle

*

WLAN Module

Power Toggle

Bluetooth Module

Power Toggle

Number Lock Toggle

Volume Decrease/

Increase

Sleep Toggle Fn + NumLk

Fn + ScrLk Scroll Lock Toggle

Display Toggle - DO NOT use when SLI is enabled Fn + 5

Audio Toggle - Toggle between Stereo and 5.1 Surround Sound Modes

Table 1 - 4 - Function Keys & Visual Indicators

System Map: Front & Rear Views

1

5

2

5

4

5

3

5

TV Tuner Module Support

Note that the TV Tuner module (factory) option is supported by the Windows Media Cen-

ter software. Windows Media Center is not included in Starter or Home Basic versions of Windows 7.

Quick Start Guide

Figure 1 - 4

Front View

1. ExpressCard Slot

(see page

2 - 7

)

2. Consumer Infrared

Transceiver

(enabled with optional TV Tuner only)

3. LED Power

Indicators

4. DC-In Jack

5. Vent/Fan Intake

1

Downloaded from LpManual.com Manuals

System Map: Front & Rear Views 1 - 11

1

Quick Start Guide

Figure 1 - 5

Right View

1. Line-In Jack

2. S/PDIF-Out Jack

3. Microphone-In Jack

4. Headphone-In Jack

5. 3 * USB 2.0 Ports

6. Security Lock Slot

System Map: Right View

1 2 3 4

5 5 5

USB Ports

Note that the connections to the USB ports only fit one way, do not force them.

6

USB 2.0 or 3.0 Ports

USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black.

System Map: Left View

1

2

3

4

5

6 6

7

8

10

9

USB 3.0 Ports

USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black. Note that

the USB 3.0 port requires a driver installation (see

“USB 3.0” on page 4 - 7

), does not support wake on USB and is not operational under DOS.

9-in-1 Card Reader

The card reader allows you to use the most popular digital storage card formats:

MMC (MultiMedia Card) / RSMMC

SD (Secure Digital) / Mini SD / SDHC / SDXC Compatible

MS (Memory Stick) / MS Pro / MS Duo

HDMI Ports

Note that the HDMI Ports support video and audio signals to attached external displays

(also see

“HDMI Ports” on page 2 - 7

).

Quick Start Guide

Figure 1 - 6

Left View

1. Speaker

2. DVI-Out Port

3. Cable (CATV)

Antenna Jack

*

4. RJ-45 LAN Jack

5. HDMI-Out Port

6. 2 * USB 3.0 Ports

7. eSATA Port

8. Mini-IEEE 1394b Port

9. 9-in-1 Card Reader

10. Optical Device Drive

Bay

*Enabled with Optional

Mini-PCI TV Tuner Only

Mini-IEEE 1394b Port

The Mini-IEEE 1394b port only supports SELF POW-

ERED IEEE 1394 devices.

1

Downloaded from LpManual.com Manuals

System Map: Left View 1 - 13

1

Quick Start Guide

Disk Eject Warning

Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice.

CD/DVD Emergency Eject

If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. Do not use a sharpened pencil or any object that may break and become lodged in the hole.

Don’t try to remove a floppy disk/CD/DVD while the system is accessing it. This may cause the system to

“crash”.

Changing DVD Regional Codes

Go to the Control Panel and double-click Device

Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the

DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.

DVD region detection is device dependent, not OSdependent. You can select your module’s region code 5 times. The fifth selection is permanent. This cannot be altered even if you change your operating system or you use the module in another computer.

System Map: Bottom View

2

3

2 2

Quick Start Guide

Figure 1 - 7

Bottom View

1. Sub Woofer

2. Fan Outlet/Intake

3. Component Bay

Cover

4. Battery

(Secondary HDD

Bay - HDD3)

5. Primary HDD Bay

(HDD1 & 2)

1

4

1

5

Battery Information

Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See

“Battery Information” on page 3 - 10

for full instructions.

Downloaded from LpManual.com Manuals

Overheating

To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use.

System Map: Bottom View 1 - 15

1

Quick Start Guide

Windows 7 Start Menu & Control Panel

Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.

Click here to toggle Category View

Figure 1 - 8 - Start Menu & Control Panel

In many instances throughout this manual you will see an instruction to open the Control Panel. The Control

Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features in Windows (e.g. power, video, network, audio etc.). Windows 7 provides basic controls for many of the features, however many new controls are added (or existing ones are enhanced) when you install the drivers. To see all controls it may be necessary to toggle off Category View to view the control panel icons.

Quick Start Guide

Video Features

This computer features two different (either AMD or NVIDIA) video options. You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Win-

dows 7.

To access Display (Control Panel) and Screen Resolution in Windows:

1.

Click Start and click Control Panel.

2.

Click Display (icon) - In the Appearances and Personalization category.

3.

Click Adjust Screen Resolution/Adjust resolution.

OR

4.

Alternatively you can right-click the desktop and select Screen resolution

1

(

Figure 1 - 9 on page 1 - 18

).

5.

Use the dropbox to select the screen Resolution

2

(

Figure 1 - 9 on page 1 - 18

).

NVIDIA & AMD Video Controls

More detailed video controls are provided by the NVIDIA Control Panel or Catalyst Control Center. For more detailed information see see

“NVIDIA Control Panel” on page 1 - 19

/

“Catalyst Control Center” on page 1 - 20

and

Appendix

B

or

Appendix C

.

You can also access the control panels by right-clicking the desktop and selecting NVIDIA Control Panel/Catalyst (TM)

Control Center (

Figure 1 - 10 on page 1 - 19

/

Figure 1 - 11 on page 1 - 20

).

1

Downloaded from LpManual.com Manuals

Video Features 1 - 17

1

Quick Start Guide

Screen Resolution

Video Options

Note that card types, specifications and drivers are subject to continual updates and changes.

Check with your service center for the latest details on video cards supported.

1

Figure 1 - 9 - Screen Resolution

2

Quick Start Guide

NVIDIA Control Panel

You can access the NVIDIA Control Panel as follows:

1.

Click Start, and click Control Panel.

2.

Click NVIDIA Control Panel

1

(

Figure 1 - 10

) - In the Appearances and Personalization category.

3.

See

“NVIDIA Video Driver Controls” on page B - 1

for full details on control panels etc.

OR

4.

You can also access the control panel by right-clicking the desktop and selecting NVIDIA Control Panel

2

.

1

2

1

Downloaded from LpManual.com Manuals

Figure 1 - 10 - NVIDIA Control Panel

Video Features 1 - 19

1

Quick Start Guide

Catalyst Control Center

You can access the Catalyst

TM

Control Center as follows:

1.

Right-click the desktop and select Catalyst Control Center

1

(

Figure 1 - 11

).

OR

2.

Double-click the icon

2

(

Figure 1 - 11

) in the Windows notification area (or right-click the icon and select

Catalyst Control Center).

3.

See

“AMD Video Driver Controls” on page C - 1

for full details on control panels etc.

1

Right-Click for Menu

2

Figure 1 - 11 - Catalyst Control Center Access

Quick Start Guide

Power Options

The Power Options (Hardware and Sound menu) control panel icon in Windows (see page

1 - 16

) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.

Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to create a new plan. Click Change plan settings and click Change advanced power settings to access further configuration options.

Pay attention to the instructions on battery care in

“Battery Information” on page 3 - 10

.

1

Downloaded from LpManual.com Manuals

Figure 1 - 12 - Power Options

Power Options 1 - 21

1

Quick Start Guide

Storage Devices, Mouse, Audio & Printer

Chapter 2: Storage Devices, Mouse, Audio &

Printer

Overview

Read this chapter to learn more about the following main features and components of the computer:

• Hard Disk Drive

• Optical Device

• Multi-In-1 Card Reader

• ExpressCard Slot

• Audio Features

• HDMI Audio Configuration

• Adding a Printer

2

Downloaded from LpManual.com Manuals

Overview 2 - 1

2

Storage Devices, Mouse, Audio & Printer

Power Safety

Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer.

Hard Disk Drive

The hard disk drive(s) issuer) used to store your data in the computer. The hard disks) can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm. The primary hard disk bay

1

is accessible from the bottom of your computer as seen below, and the secondary hard disk bay

2

is located under the battery compartment.

The computer can accommodate up to three hard disks (two in the primary bay, and one in the secondary bay), and these may be configured in RAID or AHCI modes.

Further details on removing and inserting the hard disk are available in

“Upgrading the Hard Disk Drive(s)” on page 6 - 4

.

Figure 2 - 1

Hard Disk Location

1

2

Storage Devices, Mouse, Audio & Printer

Optical Device

There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the model you purchased (see

“Storage” on page D - 3

). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS ( see

“Boot Menu” on page 5 - 15

).

Loading Discs

To insert a CD/DVD, press the open button

1

and carefully place a CD/DVD onto the disc tray with label-side facing up (use just enough force for the disc to click onto the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you are ready to start. The busy indicator

2

will light up while data is being accessed, or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole

3

to open the tray.

Sound Volume

Adjustment

How high the sound volume can be set depends on the setting of the volume control within Win-

dows. Click the Volume icon on the taskbar to check the setting.

Peripherals must be connected before you turn on the system.

2

2

1

3

Figure 2 - 2

Optical Device

Downloaded from LpManual.com Manuals

Optical Device 2 - 3

2

Storage Devices, Mouse, Audio & Printer

CD Emergency Eject

If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole.

Handling CDs or DVDs

Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.

Note the following:

• Hold the CD or DVD by the edges; do not touch the surface of the disc.

• Use a clean, soft, dry cloth to remove dust or fingerprints.

• Do not write on the surface with a pen.

• Do not attach paper or other materials to the surface of the disc.

• Do not store or place the CD or DVD in high-temperature areas.

• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.

• Do not bend the CD or DVD.

• Do not drop or subject the CD or DVD to shock.

Disk Eject Warning

Don’t try to remove a

CD/DVD while the system is accessing it. This may cause the system to “crash”.

Storage Devices, Mouse, Audio & Printer

DVD Regional Codes

To change the DVD regional codes see

“Changing DVD Regional Codes” on page 1 - 14

.

Region

1

2

3

4

5

6

DVD Regional Coding

Geographical Location

USA, Canada

Western Europe, Japan, South

Africa, Middle East & Egypt

South-East Asia, Taiwan, South

Korea, The Philippines, Indonesia,

Hong Kong

South & Central America, Mexico,

Australia, New Zealand

N Korea, Russia, Eastern Europe,

India & Most of Africa

China

Table 2 - 1

DVD Regional Coding

2

Downloaded from LpManual.com Manuals

Optical Device 2 - 5

2

Storage Devices, Mouse, Audio & Printer

Card Reader Cover

Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader.

Multi-In-1 Card Reader

The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the card reader driver (see

“Card Reader” on page 4 - 7

).

• MMC (MultiMedia Card) / RSMMC

• SD (Secure Digital) / Mini SD / SDHC / SDXC

• MS (Memory Stick) / MS Pro / MS Duo

Note: Some of these cards require PC adapters that are usually supplied with the cards.

Figure 2 - 3

Right View

1.

Card Reader

1

Storage Devices, Mouse, Audio & Printer

ExpressCard Slot

The computer is equipped with an ExpressCard/34 slot that reads Express Card/34 formats. ExpressCards are the successors to PCMCIA (PC Cards).

Inserting and Removing ExpressCards

• Press the cover to eject it before inserting an ExpressCard.

• Align the ExpressCard with the slot and push it in until it locks into place.

• To remove an ExpressCard, simply press the card to eject it.

ExpressCard

Slot Cover

Make sure you keep the cover in the Express-

Card slot when not in use. This will help prevent foreign objects and/ or dust getting in to the

ExpressCard Slot.

1

Figure 2 - 4

Express Card Slot

2

1.

ExpressCard

Slot

Downloaded from LpManual.com Manuals

ExpressCard Slot 2 - 7

2

Storage Devices, Mouse, Audio & Printer

Audio Features

Sound Volume

Adjustment

The sound volume level is set using the volume control within Windows

(and the volume function keys on the computer). Click the volume icon in the taskbar to check the setting.

panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ control panel (right-click the taskbar icon to bring up an audio menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination or by pressing your finger on either end of the Touch Sensor volume control (see

Table 1 - 3, on page 1 - 8

).

Figure 2 - 5

Realtek Audio

Manager

Right-click the icon to access the menu above.

See

“HDMI Audio Configuration” on page 2 - 13

for a description of the audio configuration when connecting an HDMI supported display device.

Storage Devices, Mouse, Audio & Printer

Setup for Audio Recording

To record audio sources on your computer at optimum quality follow the instructions below:

1.

Click Start, and click Control Panel (or point to Settings and click Control Panel) and make sure you are in Classic View.

2.

Click Realtek HD Audio Manager (or right-click the taskbar icon and select

Sound Manager).

3.

Click Microphone Effects (tab) in Microphone (tab), and then click to select

Noise Suppression (button), or adjust the Recording Volume level to around 60, to obtain the optimum recording quality.

4.

Click OK to close the control panel and save the settings.

2

Figure 2 - 6

Realtek Audio

Manager -

Recording Setup

Downloaded from LpManual.com Manuals

Audio Features 2 - 9

2

Storage Devices, Mouse, Audio & Printer

Fn + 5 Audio Toggle

The Fn + 5 key combination allows you to toggle the audio system between stereo and surround modes. The stereo mode will allow for a louder audio volume.

Note that if you have stereo mode enabled, and attempt to demo the speaker configuration, then the sound will only be enabled through the front and rear speakers.

Figure 2 - 7

Speaker

Configuration (7.1)

Setup for 5.1 or 7.1 Surround Sound

To setup your system for 5.1 or 7.1 surround sound you will need to connect the audio cables to the Headphone-Out, Line-In, Microphone-In jack and S/PDIF-Out jacks (note: the S/PDIF jack is used for 7.1 surround sound only) .

1.

Click Start, and click Control Panel (or point to Settings and click Control Panel) and make sure you are in Classic View.

2.

Click Realtek HD Audio Manager (or right-click the taskbar icon and select

Sound Manager).

3.

Click Speakers (tab) and click Speaker Configuration (tab).

4.

Select 5.1 or 7.1 Speaker from the Speaker Configuration pull-down menu.

Connector Settings

Auto Popup Dialog

You should enable the auto popup dialog to automatically detect when a device has been plugged-in. If disabled, double-click connector

settings

and click the box to enable the auto popup detection of plugged-n devices.

Storage Devices, Mouse, Audio & Printer

5.

Plug the front speaker cables into the Headphone-Out Jack.

6.

Plug in the other cables (you may require an adapter to connect each cable to the appropriate jack e.g a stereo mini to dual RCA adapter) from your speakers as follows:

• Line-In Jack = Rear Speaker Out

• Microphone-In Jack = Center/Subwoofer Speaker Out

• S/PDIF-Out Jack = Side Speaker Out (for 7.1 Surround Sound Only)

7.

As you plug in each cable a dialog box will pop up (see

“Auto Popup Dialog” on page 2 - 10

).

8.

Click to put a tick in the appropriate box according to the speaker plugged-in (e.g.

Rear Speaker Out), and then click OK to save the setting.

9.

Click OK to exit Realtek HD Audio Manager.

Figure 2 - 8

Connected Device

Auto Popup

2

Note: Side Speaker Out is required for 7.1 Surround only.

Downloaded from LpManual.com Manuals

Audio Features 2 - 11

2

Storage Devices, Mouse, Audio & Printer

Dolby Settings

You can adjust the Dolby settings from the Dolby tab in Speakers Properties.

1.

Click Start, and click Control Panel (or point to Settings and click Control Panel).

2.

Click Sound (Hardware and Sound).

3.

Click Playback (tab).

4.

Double-click Speakers (or select Properties from the right-click menu).

5.

Click Dolby (tab)

6.

Adjust the settings to your preferences and click OK.

Figure 2 - 9

Speakers Properties

Dolby Settings

Storage Devices, Mouse, Audio & Printer

HDMI Audio Configuration

As HDMI (High-Definition Multimedia Interface) carries both audio and video signals you can configure the audio output as per the instructions below.

Audio Setup for HDMI

1.

Click Start, and click Control Panel (or point to Settings and click Control Panel).

2.

Click Sound (Hardware and Sound).

3.

Click Playback (tab), and click to select Realtek Digital Output.

4.

Click Set Default (button).

5.

Click OK to close the Sound control panel.

6.

Select Speakers as the default for standard audio sources.

2

Figure 2 - 10

Sound Playback

Options

Downloaded from LpManual.com Manuals

Audio Features 2 - 13

2

Storage Devices, Mouse, Audio & Printer

Audio Setup for LCD Monitors/TVs with HDMI Input

Some LCD monitors/TVs support HDMI input, but DO NOT have built-in digital audio decoders. Where this is the case, when playing DVDs in Windows Media

Player/CyberLink Power DVD, a background noise can occur. If this situation does arise then please follow the instructions below.

1.

Click Start, and click Control Panel (or point to Settings and click Control Panel).

2.

Click Sound (Hardware and Sound).

3.

Double-click Realtek Digital Output.

4.

Click Supported Formats (tab).

5.

Click to disable (remove the check in the box) DTS Audio and Dolby Digital.

6.

Click OK and close the control panels.

Figure 2 - 11

Sound

Supported Formats

Storage Devices, Mouse, Audio & Printer

HDMI Notes

• Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device.

• If you disconnect the HDMI cable the default audio playback device will not revert to speakers until the computer is restarted (if you do not wish to restart the computer then go to the Sound control panel and select Speakers as the default audio playback device).

HDMI Video Configuration

1.

Connect an HDMI cable from the HDMI-Out port to your external display.

2.

Configure your external display as per the instructions in

“Configuring an

External Display using the NVIDIA Control Panel” on page B - 7

.

3.

Set up your external display (TV or LCD) for HDMI input (see your display device manual).

4.

You can now play video/audio sources through your external display.

Other Applications

If you are using a third party application to play

DVDs etc. you will need to consult the application’s documentation to see the appropriate audio configuration (the application must support digital to analog translation).

2

Downloaded from LpManual.com Manuals

Audio Features 2 - 15

2

Storage Devices, Mouse, Audio & Printer

Mouse Driver

If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions.

Be sure to check the device’s user documentation for details.

TouchPad and Buttons/Mouse

The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.

Storage Devices, Mouse, Audio & Printer

Once you have installed the TouchPad driver (see

“TouchPad” on page 4 - 8

) you can configure the functions from the Mouse control panel in Windows, or by doubleclicking the TouchPad driver icon on the taskbar. You may then configure the

TouchPad tapping, buttons, scrolling, pointer motion and sensitivity options to your preferences. You will find further information at www.synaptics.com.

TouchPad Scrolling

This computer model series may feature different

TouchPad versions.

These TouchPads may differ in their vertical scrolling function in most scrollable windows.

Some TouchPads require sliding the finger up and down on the right of the

TouchPad to scroll the window. Other versions require tapping/holding down the finger at the top right or bottom right of the

TouchPad to scroll the window.

2

Figure 2 - 12

Mouse Properties

Downloaded from LpManual.com Manuals

TouchPad and Buttons/Mouse 2 - 17

2

Storage Devices, Mouse, Audio & Printer

Show Video

You can get a clearer view of the gestures involved by clicking the

Show Video option for each gesture item.

Select the gesture (Pinch

Zoom, Rotating, Three

Fingers Down and

Three Finger Flick) in the

Device Settings > Set-

tings left tree menu and click the Show Video button to see the demonstration video.

For more details on any of the gestures see the help in the lower part of the right menu window.

Gestures and Device Settings

The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the TouchPad to perform specific actions to manipulate documents, objects and applications.

You can configure the settings from the Device Settings tab in Mouse Properties:

1.

Click Start, and click Control Panel (or point to Settings and click Control Panel).

2.

Click Mouse (Hardware and Sound).

3.

Click Device Settings (tab) and click Settings.

4.

Use the menu tree on the left to access the user configurable settings.

Figure 2 - 13

Mouse Properties -

Device Settings

Storage Devices, Mouse, Audio & Printer

Scrolling

The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the

TouchPad surface and slide both fingers in the direction required (in a straight continuous motion).

Figure 2 - 14

Scrolling Gesture

2

Zooming

The Pinch Zoom gesture can be used to perform the same function as a scroll wheel in Windows applications that support CTRL + scroll wheel zoom functionality.

Place two fingers on the TouchPad (for best results use the tips of the fingers) and slide them apart to zoom in, or closer together to zoom out.

Figure 2 - 15

Zooming Gesture

Downloaded from LpManual.com Manuals

TouchPad and Buttons/Mouse 2 - 19

2

Storage Devices, Mouse, Audio & Printer

Rotating

Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments.

Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the TouchPad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.

Figure 2 - 16

Rotating Gesture

Three Finger-Flick/Three Fingers Down (Press)

The Three Finger-Flick gesture may be used to enhance navigation with a variety of applications such as browsing the Internet or scrolling through a photo viewer. The

Three Fingers Down gesture may be used to launch user-selectable applications.

Figure 2 - 17

Flick/Press

Gesture

Storage Devices, Mouse, Audio & Printer

Adding a Printer

The most commonly used peripheral is a printer. The following conventions will help you to add a printer; however it is always best to refer to the printer manual for specific instructions and configuration options.

USB Printer

Most new printers have a USB interface connection. You may use any one of the ports to connect the printer.

Install Instructions:

1.

Set up the printer according to its instructions (unpacking, paper tray, toner/ink cartridge etc.).

2.

Turn ON the computer.

3.

Turn ON the printer.

4.

Connect the printer’s USB cable to one of the USB ports on the computer.

5.

Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions.

Parallel Printer

This is still a very common type of printer. The install instructions are in the sidebar

(you will need to purchase a parallel to USB converter).

Parallel Printer

After setting up the printer attach the parallel cable to the printer.

Connect the printer’s parallel cable to the Parallel to USB converter, and then plug the converter into the USB port.

Turn ON the printer, then turn ON the computer.

Windows will identify the printer and either load one of its own drivers or ask you to supply one.

Follow the on-screen instructions.

2

Downloaded from LpManual.com Manuals

Adding a Printer 2 - 21

2

Storage Devices, Mouse, Audio & Printer

Power Management

Chapter 3: Power Management

Overview

To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer

(the monitor and hard disk drive) or the whole system.

This chapter covers:

• The Power Sources

• Turning On the Computer

• Power Plans

• Power-Saving States

• Configuring the Power Buttons

• Battery Information

The computer uses enhanced power saving techniques to give the operating system

(OS) direct control over the power and thermal states of devices and processors. For example, this enables the OS to set devices into low-power states based on user settings and information from applications.

OS Note

Power management functions will vary slightly depending on your operating system. For more information it is best to refer to the user’s manual of your operating system.

(Note: All pictures used on the following pages are from the Windows 7

OS.)

3

Downloaded from LpManual.com Manuals

Overview 3 - 1

3

Power Management

The Power Sources

The computer can be powered by either an AC/DC adapter or a battery pack.

AC/DC Adapter

Use only the AC/DC adapter that comes with your computer. The wrong type of AC/

DC adapter will damage the computer and its components (see page

D - 5

).

1.

Attach the AC/DC adapter to the DC-In jack at the rear of the computer.

2.

Plug the AC power cord into an outlet, and then connect the AC power cord to the

AC/DC adapter.

3.

Raise the lid/LCD to a comfortable viewing angle.

4.

Press the power button to turn “On”.

Battery

The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge

completely before recharging (see

“How do I completely discharge the battery?” on page 3 - 14

).

We recommend that you do not remove the battery. For more information on the battery, please refer to

“Battery Information” on page 3 - 10

.

Power Management

Turning On the Computer

Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.

When the computer is on, you can use the power button as a Stand by/Hibernate/

Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use

Power Options in the Windows control panel to configure this feature.

Shut Down

Note that you should always shut your computer down by choosing the Shut Down command from the bottom right of the Start menu in Windows. This will help prevent hard disk or system problems.

Forced Off

If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off.

Power Button as

Stand by or

Hibernate Button

You can use the OS’s

Power Options control panel to set the power button to send the system into Stand by or Hibernate mode (see your

OS’s documentation, or

“Configuring the Power Buttons” on page 3

- 8

for details).

3

Downloaded from LpManual.com Manuals

Turning On the Computer 3 - 3

3

Power Management

Resuming

Operation

See

Table 3 - 1, on page 3 - 9

for information on how to resume from a power-saving state.

Password

It is recommended that you enable a password on system resume in order to protect your data.

Power Plans

The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.

The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity.

Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.

Figure 3 - 1

Power Plan

Advanced Settings

(Win 7)

Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).

Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) powered.

Power Management

3

Click to Show/Hide additional power plans

Figure 3 - 2

Power Plans (Win 7)

Downloaded from LpManual.com Manuals

Power Plans 3 - 5

3

Power Management

Power-Saving States

You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states.

Sleep

In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.

The PC wakes from Sleep within seconds and will return you to where you last left off (what was on your desktop) without reopening the application(s) and file(s) you last used.

If your mobile PC in Sleep is running on battery power the system will use only a minimum amount of power. After an extended period the system will save all the information to the hard disk and shut the computer down before the battery becomes depleted.

Hibernate

Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hi-

bernate will also return you to where you last left off within seconds. You should put your mobile PC into Hibernate if you will not use the computer for a period of time, and will not have the chance to charge the battery.

Shut down

You should Shut down the computer if you plan to install new hardware (don’t forget to remove the battery and follow all the safety instructions in Chapter 6), plan to be away from the computer for several days, or you do not need it to wake up and run a scheduled task. Returning to full operation from Shut down takes longer than from Sleep or Hibernate.

Power Management

3

Win 7

Figure 3 - 3

Start Menu Power

Downloaded from LpManual.com Manuals

Power-Saving States 3 - 7

3

Power Management

Password

Protection

It is recommended that you enable a password on wake up in order to protect your data.

However you can disable this setting from the

Power Options menu by clicking Require a

password on wakeup

in the left menu, and selecting the options (click

Change settings that are currently unavail-

able).

Configuring the Power Buttons

The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu.

Figure 3 - 4

Power Options

Define Power

Buttons

Power Management

Resuming Operation

You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo).

Power Status

Power Off

Sleep

Off

Blinking Green

To Resume

Press the Power Button

Press the Power Button

Press the Sleep Button (Fn + F4 Key Combo)

Hibernate

Display Turned Off

Off (battery)

Orange (AC/DC adapter)

Green

Press the Power Button

Press a Key or Move the Mouse/Touchpad

Closing the Lid

If you have chosen to send the computer to

Sleep when the lid is closed, raising the lid will wake the system up.

Table 3 - 1

Resuming

Operation

3

Power Button

When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down hot key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down).

Downloaded from LpManual.com Manuals

Configuring the Power Buttons 3 - 9

3

Power Management

Low Battery

Warning

When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted.

Battery Information

Follow these simple guidelines to get the best use out of your battery.

Battery Power

Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from

power plan Change plan settings > Change advanced power settings (see

Figure

3 - 1 on page 3 - 4

).

Click the battery icon in the taskbar to see the current battery level and charge status.

Figure 3 - 5

Battery Icon

(Taskbar) & Battery

Advanced Settings

Power Management

Conserving Battery Power

• Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance.

• Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter.

• Reduce the amount of time before the display is turned off.

• Close wireless, Bluetooth, modem or communication applications when they are not being used.

• Disconnect/remove any unnecessary external devices e.g. USB devices,

ExpressCards etc.

Windows Mobility

Center

The Windows Mobility

Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc.

3

Figure 3 - 6

Windows Mobility

Center

Downloaded from LpManual.com Manuals

Battery Information 3 - 11

3

Power Management

Battery Life

Battery life may be shortened through improper maintenance. To optimize the life

and improve its performance, fully discharge and recharge the battery at least

once every 30 days.

We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see

“Removing the Battery” on page 6 - 3

.

New Battery

Always completely discharge, then fully charge, a new battery (see

“Battery FAQ” on page 3 - 14

for instructions on how to do this).

Recharging the Battery with the AC/DC Adapter

The battery pack automatically recharges when the AC/DC adapter is attached and plugged into an electrical outlet. If the computer is powered on, and in use, it will take several hours to fully recharge the battery. When the computer is turned off but plugged into an electrical outlet, battery charge time is less. (Refer to

“LED Indicators” on page 1 - 7

for information on the battery charge status, and to

“Battery Information” on page 3 - 10

for more information on how to maintain and properly

recharge the battery pack.)

Proper handling of the Battery Pack

• DO NOT disassemble the battery pack under any circumstances.

• DO NOT expose the battery to fire or high temperatures, it may explode.

• DO NOT connect the metal terminals (+, -) to each other.

Damaged Battery Warning

Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center. If the battery has been dropped we do not recommend using it any further, as even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire. It is recommended that you replace your computer battery every two years.

Power Management

Caution

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.

3

Downloaded from LpManual.com Manuals

Battery Information 3 - 13

3

Power Management

Battery FAQ

How do I completely discharge the battery?

Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.

1.

Save and close all files and applications.

2.

Create a power plan for discharging the battery and set all the options to Never.

Figure 3 - 7

Power Plan Create

3.

Click Change plan settings (after creating it) and click Change plan settings >

Change advanced power settings.

Power Management

3

Figure 3 - 8

Change Plan

Settings / Change

Advanced Power

Settings

Downloaded from LpManual.com Manuals

Battery Information 3 - 15

3

Power Management

4.

Scroll down to Battery and click + to expand the battery options.

5.

Choose the options below (click Yes if a warning appears):

Figure 3 - 9

Power Options

Advanced Settings -

Battery

• Low battery levels = 0%

• Critical battery Levels = 1%

• Low battery action = Do Nothing

• Critical battery action (On battery) = Shut Down

• Critical battery action (Plugged in) = Do Nothing

How do I fully charge the battery?

When charging the battery, don’t stop until the LED charging indicator light changes from orange to green.

How do I maintain the battery?

Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.

SLI Multi GPU Configuration & Battery Power

Note that due to the high power and system demands created by enabling SLI Configuration, you should not enable SLI configuration if your computer is powered by battery

only. If you attempt to run an SLI configuration when the computer is powered by the battery only, then system problems may occur.

If the computer is currently powered by battery only do not enable SLI configuration.

If you have currently enabled SLI configuration, and the computer is powered by the AC/

DC adapter, do not switch to battery power only (or go to the NVIDIA Control Panel and disable SLI configuration before switching to battery power only).

Power Management

3

Downloaded from LpManual.com Manuals

Battery Information 3 - 17

3

Power Management

Drivers & Utilities

Chapter 4: Drivers & Utilities

This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to manually install some system-required drivers and utilities.

RAID & AHCI Setup

Note that setting up a RAID, or AHCI mode, needs to be done prior to installing the Windows OS, and therefore before installing the other drivers listed here (see

“Setting Up SATA RAID Mode” on page 7 - 2

).

What to Install

The Device Drivers & Utilities + User’s Manual disc contains the drivers and utilities necessary for the proper operation of the computer.

Table 4 - 1, on page 4 - 3

lists what you need to install and it is very important that the drivers are in-

stalled in the order indicated.

Module Driver Installation

The procedures for installing drivers for the WLAN,

PC Camera, Consumer Infrared (for TV tuner remote), Bluetooth & WLAN Combo and Security

(Fingerprint & TPM modules) are provided in

“Modules” on page 7 - 1

.

4

Downloaded from LpManual.com Manuals

What to Install 4 - 1

4

Drivers & Utilities

Driver Installation

Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Driv-

ers (button) to access the Optional driver menu.

1.

Check the driver installation order from

Table 4 - 1, on page 4 - 3

(the drivers must be installed in

this order) which is the same as that listed in the

Drivers Installer menu below.

2.

Click to select the driver you wish to install, (you should note down the drivers as you install them).

3.

Follow the instructions for each individual driver installation procedure as listed on the following pages.

Figure 4 - 1

- Drivers Installer Screen 1

Figure 4 - 2

- Drivers Installer Screen 2

Drivers & Utilities

Windows 7 Driver

Chipset

Video (NVIDIA)

Video (AMD)

LAN

Card Reader

TouchPad

USB 3.0

Hot Key

Audio

Page

Page 4 - 7

Page 4 - 7

Windows 7 Driver

Intel Rapid Storage Technology

(for RAID)

Wireless LAN Module

Page

Page 7 - 8

Page 7 - 15

Page 4 - 7

Page 4 - 7

Page 4 - 8

Page 4 - 8

Page 4 - 8

PC Camera Module

TV Tuner Module

Bluetooth Module

(note that you need to install both the WLAN &

Bluetooth drivers for the WLAN & Bluetooth

Combo module)

Fingerprint Reader Module

Trusted Platform Module

Page 4 - 8

Table 4 - 1

- Driver Installation

Page 7 - 33

Page 7 - 41

Page 7 - 44

Page 7 - 60

Page 7 - 67

Note that you need to install both the WLAN & Bluetooth drivers for Intel and 3rd party WLAN & Bluetooth

Combo modules.

4

Downloaded from LpManual.com Manuals

Driver Installation 4 - 3

4

Drivers & Utilities

Manual Driver Installation

Click the Browse CD/DVD button in the Drivers In-

staller application and browse to the executable file in the appropriate driver folder.

Windows Update

After installing all the drivers make sure you enable

Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). See

“Windows Update” on page 4 -

9

for instructions.

Updating/Reinstalling Individual Drivers

If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Pro-

grams > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer). Reinstall the driver as outlined in this chapter.

If the driver is not listed in the Programs and Fea-

tures menu:

1.

Click Start, and click Control Panel (or point to

Settings and click Control Panel).

2.

Double-click Device Manager (Hardware and

Sound > Device Manager).

3.

Double-click the device you wish to update/reinstall the driver for (you may need to click “+” to expand the selection).

4.

Click Driver (tab) and click the Update Driver or

Uninstall button and follow the on screen prompts.

User Account Control

If a User Account Control prompt appears as part of the driver installation procedure, click Continue/Al-

low, and follow the installation procedure as directed.

Drivers & Utilities

New Hardware Found

If you see the message “New Hardware Found” during the installation procedure (other than when out-

lined in the driver install procedure), click Cancel to close the window, and follow the installation procedure.

Windows Security Message

If you receive a Windows security message as part of the driver installation process. Just click “Install this

driver software anyway” or Install to continue the installation procedure.

You will receive this message in cases where the driver has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.

4

Downloaded from LpManual.com Manuals

Driver Installation 4 - 5

4

Drivers & Utilities

Driver Installation Procedure

Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Drivers

(button) to access the Optional driver menu.

Driver Installation General Guidelines

The driver installation procedure outlined in this

Chapter (and in Chapter 7 Options & Modules), are accurate at the time of going to press.

Drivers are always subject to upgrade and revision so the exact procedure for certain drivers may differ slightly. As a general guide follow the default on screen instructions for each driver (e.g. Next > Next

> Finish) unless you are an advanced user. In many cases a restart is required to install the driver.

RAID Note: Setting up a RAID, or AHCI mode, needs to be done prior to installing the Windows OS, and therefore before installing the other drivers listed here.

Chipset

1.

Click 1.Install Chipset Driver > Yes.

2. Click Next > Yes > Next > Next.

3. Click Finish to restart the computer.

The video driver installation procedure will depend upon which video adapter is included in your purchase option (NVIDIA or AMD).

Drivers & Utilities

Video (AMD)

1.

Click 2.Install Video Driver > Yes.

2. Click Next > Install (button).

3. Click the Express (or Custom if you prefer to manually configure the driver installation settings) button and click Next.

4. Click Accept (button) and click Yes.

5. Click Finish > Yes to restart the computer.

6. After the computer has restarted, click Restart

Now to restart again to refresh the video driver.

Video (NVIDIA)

1.

Click 2.Install Video Driver > Yes.

2. Click AGREE AND CONTINUE (button) to accept the terms of the license agreement.

3. Click NEXT.

4. Click the RESTART NOW button to restart the computer.

After the video driver has been installed, and the system restarted, the OS will automatically run the "Winsat.exe" to rate the performance. Allow time for this process to finish and do not restart during this process

(if you have restarted the system see

“Windows Update” on page 4 - 9

).

LAN

1.

Click 3.Install LAN Driver > Yes.

2. Click Install.

3. Click Finish to complete the installation.

Card Reader

1.

Click 4.Install Cardreader Driver > Yes.

2. Click Install > Finish.

4

Downloaded from LpManual.com Manuals

Driver Installation 4 - 7

4

Drivers & Utilities

TouchPad

1.

Click 5.Install Touchpad Driver > Yes.

2. Click Next.

3. Click the button to accept the license, and then click Next.

4. Click Finish > Restart Now to restart the computer.

Audio

1.

Click 8. Install Audio Driver > Yes.

2. Click Next.

3. Click Finish to restart the computer.

It is recommended that you install the Intel Rapid

Storage Technology driver (see

“Intel Rapid Storage

Technology” on page 7 - 8

- required for AHCI &

RAID mode).

USB 3.0

1.

Click 6.Install USB 3.0 Driver > Yes.

2. Click Next.

3. Click the button to accept the license and then click Next.

4. Click Next > Install.

5. Click Finish.

(see over)

Hot Key

1.

Click 7.Install Hotkey AP > Yes.

2. Click Next > Next.

3. Click Finish > Finish to restart your computer.

4.

Windows Update

After installing all the drivers make sure you enable Win-

dows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft).

To enable Windows Update make sure you are con-

nected to the internet:

1.

Click Start, and click Control Panel (or point to

Settings and click Control Panel).

2.

Click Windows Update (System and Security/

Security).

3.

Click Check for updates (button).

4.

The computer will now check for updates (you need to be connected to the internet).

5.

Click Install now (button) to begin checking for the updates.

6.

Click Install updates (button) to install the updates.

Drivers & Utilities

Windows Experience Index

After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experi-

ence Index (make sure the AC/DC adapter is plugged in):

1.

Click Start, and click Control Panel.

2. Click Performance Information and Tools

(System and Security > System > Check the

Windows Experience Index).

3. Click “Rate this computer/Refresh Now/Re-

run the assessment”.

4. The computer will take a few minutes to assess the system performance.

5. Close the control panel.

4

Downloaded from LpManual.com Manuals

Driver Installation 4 - 9

4

Drivers & Utilities

Optional Drivers

See the pages indicated for the driver installation procedures for any modules included in your purchase option.

RAID Setup

Note: Prior to setting up the RAID you will need to use an operable computer to copy the RAID driver to a

USB flash drive before installing the Windows operating system. See

“Setting Up SATA RAID Mode” on page 7 - 2

for configuration instructions.

Figure 4 - 3

- Optional Drivers Installer Screen

Bluetooth Module

If your purchase option includes the standalone V2.1

Bluetooth module then no driver is required. If your purchase option includes the Combination Wireless

LAN & V3.0 Bluetooth module then install the driver as instructed in

“3rd Party Bluetooth Combo Driver

Installation” on page 7 - 46

or

“Intel Bluetooth Combo Driver Installation” on page 7 - 54

.

Wireless LAN

See the appropriate install procedure for your WLAN module in

“Click Advanced and click Verify, then click Verify (button) to begin the process.” on page 7

- 13

.

PC Camera

See the install procedure in

“PC Camera Module” on page 7 - 32

.

Consumer Infrared (for TV Tuner Remote)

See the install procedure in

“TV Tuner Module” on page 7 - 40

.

Security Modules (Fingerprint & TPM)

See the install procedures in

“Fingerprint Reader

Module” on page 7 - 60

and

“Trusted Platform Module” on page 7 - 65

.

Drivers & Utilities

4

Downloaded from LpManual.com Manuals

Driver Installation 4 - 11

4

Drivers & Utilities

BIOS Utilities

Chapter 5: BIOS Utilities

Overview

This chapter gives a brief introduction to the computer’s built-in software:

Diagnostics: The POST (Power-On Self Test)

Configuration: The Setup utility

If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your system ever needs servicing.

There is one general rule: Don’t make any changes unless you are sure of what you

are doing. Many of the settings are required by the system, and changing them could cause it to become unstable or worse. If you have any doubts, consult your service representative.

BIOS Screens

Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s

BIOS.

BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages.

5

Downloaded from LpManual.com Manuals

Overview 5 - 1

5

BIOS Utilities

POST Screen

1.BIOS information

2.CPU type

3.Memory status

4.Enter Setup prompt appears only during

POST

Note: The POST screen as pictured right is for guideline purposes only.

The POST screen on your computer may appear slightly different. If the Boot-time Diagnos-

tic Screen is disabled

(see page

5 - 9

as per the default setting), the POST screen will not appear.

The Power-On Self Test (POST)

If you enable the Boot-time Diagnostic Screen in the Setup Utility, each time you turn on the computer the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory).

As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup.

If there are no problems, the Setup prompt will disappear and the system will load the operating system. Once that starts, you can’t get into Setup without rebooting.

1

3

2

Figure 5 - 1

POST Screen

4

BIOS Utilities

Failing the POST

Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”.

Fatal Errors

These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible.

Non-Fatal Errors

This kind of error still allows you to boot. You will get a message identifying the problem (make a note of this message!) followed by the prompt:

• Press <F1> to resume

• <F2> to enter Setup

Press F1 to see if the boot process can continue. It may work, without the correct configuration.

Press F2 to run the Setup program and try to correct the problem. If you still get an error message after you change the setting, or if the “cure” seems even worse, call for help.

Downloaded from LpManual.com Manuals

The Power-On Self Test (POST) 5 - 3

5

5

BIOS Utilities

BIOS Settings

Warning

Incorrect settings can cause your system to malfunction. To correct mistakes, return to Set-

up and restore the Set-

up Defaults with <F9>.

The Setup Utility

The Phoenix Setup utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration).

Entering Setup

To enter Setup, turn on the computer and press F2 during the POST. The prompt

(Press F2 to Enter Setup) seen in Figure 5 - 1 on page

5 - 2

is usually present for a

few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.

If the computer is already on, reboot using the Ctrl + Alt + Delete combination and then hold down F2 when prompted. The Setup main menu will appear.

BIOS Utilities

Setup Screens

The following pages contain additional advice on portions of the Setup.

Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup.

Instructions on how to navigate each screen are in the box along the bottom of the screen. If these tools are confusing, press F1 to call up a General Help screen, and then use the arrow keys to scroll up or down the page.

The Item Specific Help on the right side of each screen explains the highlighted item and has useful messages about its options.

If you see an arrow next to an item, press Enter to go to a sub-menu on that subject. The sub-menu screen that appears has a similar layout, but the Enter key may execute a command.

Setup Menus

The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configuration appropriate for your model and options.

5

Downloaded from LpManual.com Manuals

The Setup Utility 5 - 5

5

BIOS Utilities

Figure 5 - 2

Main Menu

Main Menu

System Time & Date (Main Menu)

The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.

System/Extended Memory: (Main Menu)

This item contains information on the system memory, and is not user configurable.

The system will auto detect the amount of memory installed.

BIOS Revision/VGA Card etc. (Main Menu)

This item contains information on the BIOS version and video card etc., and is not user configurable.

BIOS Utilities

5

Downloaded from LpManual.com Manuals

Main Menu 5 - 7

5

BIOS Utilities

Advanced Menu

Figure 5 - 3

Advanced Menu

Advanced Chipset Control (Advanced Menu)

The sub-menu here allows you to enable/disable some advanced system features.

BIOS Utilities

SATA Mode Selection (Advanced Menu)

You may enable/disable SATA RAID or AHCI mode for your hard disks, however

you should only enable/disable SATA RAID or AHCI BEFORE installing an

operating system, and after you have backed up all necessary files and data (see sidebar). See

“Setting Up SATA RAID Mode” on page 7 - 2

for details.

Legacy USB Support: (Advanced Menu)

Choose “Enabled” if you intend to use USB devices in systems which do not normally support USB functionality (e.g. DOS). The default setting is “Enabled” and does not need to be changed if you intend to use your USB devices in Windows.

Boot-time Diagnostic Screen: (Advanced Menu)

Use this menu item to enable/disable the Boot-time Diagnostic Screen. Enable this

item to display the POST screen (see

“The Power-On Self Test (POST)” on page 5

- 2

).

Reset Configuration Data (Advanced Menu)

This item is set to No as default. You can change the setting to Yes if you have installed a new add-on which has reconfigured the system, resulting in such a serious system conflict that the operating system is unable to boot.

SATA Mode

If you have installed the

Windows 7 operating system with either AHCI

or RAID mode enabled,

DO NOT disable the set mode (if you wish to disable the set mode you will need to reinstall the

Windows 7 OS).

5

Downloaded from LpManual.com Manuals

Advanced Menu 5 - 9

5

BIOS Utilities

Power On Boot Beep (Advanced Menu)

Use this menu item to enable/disable the beep as the computer starts up.

Battery Low Alarm Beep: (Advanced Menu)

Use this menu item to enable/disable the battery low alarm beep.

BIOS Utilities

Advanced Chipset Control Menu

Figure 5 - 4

Advanced Chipset

Control Menu

Bluetooth Power Setting > Advanced Chipset Control

You can adjust the Bluetooth module power setting to your preference. The default setting (Disabled) will see the Bluetooth module powered off when the system is started up or restarted. Enabling the power setting will have the module retain the last power status (on or off) before any restart or shut down.

Downloaded from LpManual.com Manuals

Advanced Chipset Control Menu 5 - 11

5

5

BIOS Utilities

Intel Virtualization Technology > Advanced Chipset Control

Intel(R) Virtualization Technology enables a CPU to act as if it were several CPUs working in parallel in order to allow several operating systems to run at the same time in the same machine.

Hyperthreading > Advanced Chipset Control

Hyperthreading activates additional CPU threads that may appear as additional processors and is used to improve CPU multi-tasking. The operating system will view a processor with Hyperthreading enabled as two virtual processors and will spread any tasks between them (make sure your installed operating system supports multiple processors, and preferably, is optimized for this technology). After enabling/disabling Hyperthreading, and saving and exiting the BIOS, the system will shut down

(press the power button to turn the system on again).

CPU C State > Advanced Chipset Control

Enable/Disable CPU C States (operating states) here.

Turbo Boost > Advanced Chipset Control

You can enable Turbo Boost to automatically run the processor core faster than the stated frequency (within specification limits of the Thermal Design Power) for increased performance.

Security Menu

BIOS Utilities

Security Menu

The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on.

These settings do not affect your machine or network passwords which will be set in your software OS.

5

Set Supervisor Password (Security Menu)

You can set a password for access to the Phoenix SecureCore Setup Utility. This will not affect access to the computer OS (only the Phoenix SecureCore Setup

Utility).

Figure 5 - 5

Security Menu

Downloaded from LpManual.com Manuals

Security Menu 5 - 13

5

BIOS Utilities

Password Warning

If you set a boot password (Password on boot is “Enabled“), NEVER forget your password.

The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.

Set User Password (Security Menu)

You can set a password for user mode access to the Phoenix SecureCore Setup

Utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a Password on Boot (see below). Many menu items in the Phoenix

SecureCore Setup Utility cannot be modified in user mode. You can only set the user password after you have set the supervisor password.

Password on boot (Security Menu)

Specify whether or not a password should be entered to boot the computer (you may

only set a password on boot if a supervisor password is enabled). If “Enabled” is selected, only users who enter a correct password can boot the system (see the

warning in the sidebar). The default setting is “Disabled”.

Note: To clear existing passwords press Enter and type the existing password, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance.

TPM State

BIOS Utilities

Password

Protection

Note that you should set a supervisor password in the BIOS to protect the TPM information from being tampered with by unauthorized users.

5

Figure 5 - 6

TPM State

Change TPM State (TPM State)

This menu allows you to set the level of TPM functionality. You can enable/disable the TPM function altogether, or clear all existing TPM information.

Note: If you clear all TPM information it will be erased altogether and the information will need to be reconfigured.

Downloaded from LpManual.com Manuals

TPM State 5 - 15

BIOS Utilities

5

Figure 5 - 7

Physical Presence

Operations

If you have made any changes to the TPM State you will be asked to execute or reject the changes made after you have saved and exited the BIOS. Highlight the required option (it will be white), and then press Enter to save it.

BIOS Utilities

Boot Menu

Figure 5 - 8

Boot Menu

When you turn the computer on it will look for an operating system (e.g. Windows

7) from the devices listed in this menu, and in this priority order. If it cannot find the operating system on that device, it will try to load it from the next device in the order specified in the Boot priority order. Item specific help on the right is available to help you move devices up and down the order.

BIOS Screens

Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s

BIOS.

BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages.

5

Downloaded from LpManual.com Manuals

Boot Menu 5 - 17

5

BIOS Utilities

Figure 5 - 9

Exit Menu

Exit Menu

Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Set-

up defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.

Upgrading The Computer

Chapter 6: Upgrading The Computer

Overview

This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help. Before you begin you will need:

• A small crosshead or Phillips screwdriver

• A small regular slotted (flathead) screwdriver

• An antistatic wrist strap

Before working with the internal components you will need to wear an antistatic wrist strap to ground yourself because static electricity may damage the components.

The chapter includes:

• Removing the Battery

• Upgrading the Hard Disk Drive(s)

• Upgrading the Optical (CD/DVD) Device

• Upgrading the System Memory (RAM)

Please make sure that you review each procedure before you perform it.

Warranty Warning

Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.

6

Downloaded from LpManual.com Manuals

Overview 6 - 1

6

Upgrading The Computer

Power Safety Warning

Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines).

When Not to Upgrade

These procedures involve opening the system’s case, adding and sometimes replacing parts.You should not perform any of these upgrades if:

• Your system is still under warranty or a service contract

• You don’t have all the necessary equipment

• You’re not in the correct environment

• You doubt your abilities

Under any of these conditions, contact your service representative to purchase or replace the component(s).

It is advisable to also remove your battery in order to prevent accidentally turning the machine on. Before re-

moving the battery disconnect the AC/DC adapter from the computer first.

Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before turning the computer on.

Upgrading the Processor

If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.

Upgrading The Computer

Removing the Battery

If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. Before removing the battery disconnect the AC/

DC adapter from the computer first.

1.

Turn the computer off, remove the AC/DC adapter and turn it over.

2.

Loosen screws

1

-

3

and carefully lift the battery

4

up.

3.

Remove the battery from the battery bay.

Warranty Warning

Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.

6

1 2 3

Figure 6 - 1

Battery Removal

4

4

Downloaded from LpManual.com Manuals

Removing the Battery 6 - 3

6

Upgrading The Computer

HDD System Warning

New HDD’s are blank. Before you begin make sure:

You have backed up any data you want to keep from your old HDD.

You have all the CD-ROMs and FDDs required to install your operating system and programs.

If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.

Upgrading the Hard Disk Drive(s)

The hard disk drive(s) can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5mm (h) (see

“Storage” on page D - 3

). Follow your operating system’s installation instructions, and install all necessary drivers and utilities (as outlined in

“Drivers & Utilities” on page 4 - 1

), when setting up a new hard disk.

Upgrading The Computer

Removing the Hard Disk(s) from the Primary HDD Bay

1.

Turn the computer off, remove the AC/DC adapter, turn it over and remove the battery.

2.

Locate the hard disk bay cover and remove screws

1

&

2

.

3.

Remove the hard disk bay cover

3

.

RAID Hard Disks

All hard disks in a RAID should be identical (the same size and brand) in order to prevent unexpected system behavior.

1 2

Figure 6 - 2

Primary HDD Bay

Cover Screws &

Cover Removal

6

3

Downloaded from LpManual.com Manuals

Upgrading the Hard Disk Drive(s) 6 - 5

6

Upgrading The Computer

4.

Disconnect the HDD cable

4

.

5.

Remove screws

5

-

8

from the hard disk assembly.

6.

Pull the tab

9

to disconnect the hard disk assembly from the connector.

7.

Remove the hard disk assembly

10

.

8.

Remove the HDD board & cable

11

.

Figure 6 - 3

Hard Disk Assembly

Screws & Removal

5

4 6

9

7 8

11

10

Upgrading The Computer

9.

Remove screws

12

-

15

(depending on how many hard disks you have installed in the assembly).

10. Remove the hard disk(s)

16

from the case.

14

14

13

13

15

15

Figure 6 - 4

Hard Disk(s)

Removal

12

12

6

16

Downloaded from LpManual.com Manuals

16

Upgrading the Hard Disk Drive(s) 6 - 7

6

Upgrading The Computer

11. If two hard disks are installed then an insulation plate will be installed on the upper hard disk.

12. Remove screws

17

-

20

and the insulation plate

21

.

13. Reverse the process to install any new disk(s) and do not forget to install the insulation plate (onto the upper hard disk in the orientation illustrated below), screws, cables and covers (pay careful attention to the orientation of the hard disks in the case).

19

Figure 6 - 5

Upper HDD

Insulation Plate

Removal

18

21 20

17

Upgrading The Computer

Inserting the Primary Hard Disk(s)

1.

Insert the HDD(s)

1

into the case as illustrated (make sure the cable connec-

tors are facing towards the gap at the rear of the case, and that the upper HDD insulation plate is installed).

2.

Insert screws

2

-

5

to secure the hard disk(s) in the case.

Figure 6 - 6

HDD Insertion &

Screws

6

1

1

3

2

2

5

Downloaded from LpManual.com Manuals

4

2

3

4

3

5

Upgrading the Hard Disk Drive(s) 6 - 9

Upgrading The Computer

3.

Firmly insert the HDD cable

6

into the hard disk case

7

as indicated below.

4.

Insert the HDD assembly into the bay by pushing it straight down (do not insert the assembly at an angle).

5.

Firmly connect cable

8

and then secure the assembly with screws

9

-

12

.

6

6

Figure 6 - 7

HDD Cable Insertion

& Bay Screws/Cable

Connection

7

9

8

10

12 11

Upgrading The Computer

Removing the Hard Disk from the Secondary HDD Bay

1.

Remove the battery (the Secondary hard disk bay is located under the battery).

2.

Remove screws

1

-

4

from the hard disk assembly.

3.

Grip the tab and slide the hard disk assembly in the direction of the arrow

5

.

4.

Lift the hard disk assembly out of the compartment.

1

3

2

4

Figure 6 - 8

Secondary HDD

Assembly Removal

6

5

Downloaded from LpManual.com Manuals

Upgrading the Hard Disk Drive(s) 6 - 11

6

Upgrading The Computer

5.

Remove screws

6

-

9

from the hard disk assembly.

6.

Separate the HDD

10

from the case

11

.

7.

Insert the replacement HDD into the case (make sure the cable connector is

facing towards the rear of the case as illustrated below).

8.

Replace screws

6

-

9

.

9.

Insert the HDD assembly into the bay by pushing it straight down (do not insert the assembly at an angle) and then slide it in the direction of arrow

12

to lock in place.

7

Figure 6 - 9

Secondary HDD

Assembly Removal

6

8

11

9

10

12

Upgrading The Computer

Upgrading the Optical (CD/DVD) Device

1.

Locate the hard disk bay cover and remove screws

1

&

2.

Remove the hard disk bay cover

3

.

2

.

3.

Remove the screw at point

4

, and use a screwdriver to carefully push out the optical device at point

5

.

4.

Reverse the process to install any new optical device.

1

2

1

2

3

Figure 6 - 10

Removing the CD/

DVD Device

6

5

4

Downloaded from LpManual.com Manuals

Upgrading the Optical (CD/DVD) Device 6 - 13

6

Upgrading The Computer

Upgrading the System Memory (RAM)

The computer has three memory sockets for 204 pin Small Outline Dual In-line

(SO-DIMM) DDR III (DDR3) type memory modules (see

“Memory” on page D -

2

). The total memory size is automatically detected by the POST routine once you turn on your computer.

1.

Turn off the computer, and turn it over and remove the battery.

2.

Remove screws

1

&

2

from the bottom of the computer

1

2

Figure 6 - 11

LED Module Screws

Upgrading The Computer

3.

Turn the computer over, open the Lid/LCD, and carefully (a cable is connected to the underside of the LED cover module) unsnap up the LED cover module from point

3

on the right.

3

Figure 6 - 12

LED Cover Module

Removal

5

4

6

4.

Disconnect cable

4

and remove the LED cover module

5

.

Figure 6 - 13

LED Cover Module

Cable Disconnect

4

5

Downloaded from LpManual.com Manuals

Upgrading the System Memory (RAM) 6 - 15

Upgrading The Computer

5.

Remove screws

6

-

10

from the keyboard.

Figure 6 - 14

Keyboard Screws

6 7 8 9 10

6

Figure 6 - 15

Disconnect the

Keyboard Locking

Collar

6.

Carefully lift the keyboard up, being careful not to bend the keyboard ribbon cable.

7.

Disconnect the keyboard ribbon cable

11

from the locking collar socket

12

.

11

12

8.

Remove the keyboard

13

.

9.

Remove screws

14

-

16

from the keyboard shielding plate.

Upgrading The Computer

Figure 6 - 16

Keyboard Removal

6

13

14

16

Downloaded from LpManual.com Manuals

15

Figure 6 - 17

Keyboard Shielding

Plate Screws

Upgrading the System Memory (RAM) 6 - 17

6

Upgrading The Computer

10. Lift the keyboard shielding plate up in the direction of the arrow

17

.

11. Remove the keyboard shielding plate

18

.

Figure 6 - 18

Keyboard Shielding

Plate Up

17

Figure 6 - 19

Keyboard Shielding

Plate Remove

18

Upgrading The Computer

12. Gently pull the two release latches (

19

&

20

)

on the sides of the memory socket(s) in the direction indicated below.

13. The RAM module

21

will pop-up, and you can remove it.

Figure 6 - 20

RAM Module

Removal

19 19 19

20 20 20

21

14. Pull the latches to release the second module if necessary.

15. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory socket.

16. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the socket as it will go. DO NOT FORCE the module; it should fit without much pressure.

17. Press the module in and down towards the mainboard until the socket levers click into place to secure the module.

18. Replace the shielding plate (see over) screws, keyboard (reconnect the keyboard cable) and LED cover module (see the preceding pages).

Downloaded from LpManual.com Manuals

Contact Warning

Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance.

LED Module Cable

Make sure you reconnect the keyboard cable

(

11

Figure 6 - 15

). and

LED cover module cable

4

(see

Figure 6 - 12

).

Upgrading the System Memory (RAM) 6 - 19

6

Upgrading The Computer

Keyboard Shielding Plate Insertion

1.

When re-inserting the keyboard shielding plate

1

make sure you insert it by sliding it into position at an angle as illustrated by arrow

2

below, and press it down into position.

2.

Secure the plate with screws

3

-

5

.

1

6

Figure 6 - 21

Keyboard Shielding

Plate Insertion

2

3 4

5

Chapter 7: Modules

Overview

This chapter contains the information on the various modules (some of which are

optional) which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.

The chapter includes information on the following:

• Setting Up SATA RAID Mode

• Wireless LAN Module

• PC Camera Module

• TV Tuner Module

• Bluetooth Module

• Security Modules (Fingerprint & TPM)

Modules

7

Downloaded from LpManual.com Manuals

Overview 7 - 1

7

Modules

Setting Up SATA RAID Mode

RAID Hard Disks

All hard disks in a RAID should be identical (the same size and brand) in order to prevent unexpected system behavior.

AHCI Mode

Advanced Host Controller Interface (AHCI) is an interface specification that allows the storage driver to enable advanced serial ATA features such as Native Command

Queuing (for maximum hard disk efficiency and performance). AHCI mode can be supported by one, two or three hard disks.

RAID

To configure your system in Striping (RAID 0) or Mirroring (RAID 1) modes (see

Table 7 - 1, on page 7 - 3

) you will require at least two identical (see sidebar) hard disks; to configure your system in Intel® Rapid Recover Technology (Recovery) mode you will require two hard disks installed; to configure your system in Parity

Across Disks (RAID 5) mode you will require three hard disks installed.

Intel

®

Rapid Storage Technology Application

Make sure you install the Intel® Rapid Storage Technology application if you have set up your hard disk(s) in RAID mode (see

“Intel Rapid Storage Technology” on page 7 - 8

).

Modules

RAID Level Description

RAID 0

RAID 1

Recovery

Identical drives reading and writing data in parallel to increase performance. RAID 0 implements a striped disk array and the data is broken into blocks and each block is written to a separate disk drive.

Identical drives in a mirrored configuration used to protect data. Should a drive that is part of a mirrored array fail, the mirrored drive (which contains identical data) will handle all the data. When a new replacement drive is installed, data to the new drive is rebuilt from the mirrored drive to restore fault tolerance.

Two Identical drives copying data between a master and a recovery disk. This provides more control over how data is copied between the master and recovery drives, fast volume updates and the ability to view the data in Windows Explorer.

Prepare the following before setting up your serial ATA hard disks in RAID mode:

1.

The Microsoft Windows 7 OS DVD.

2.

A second (identical) hard disk installed in the Primary HDD bay.

OR

A second (identical) hard disk installed in the Primary HDD bay, and a third

(identical) hard disk in the Secondary HDD bay if required.

3.

The Device Drivers & Utilities + User’s Manual disc.

Table 7 - 1

RAID Levels

Array Types

A

Mirrored Array

(RAID 1) provides full data protection, as data can simply be copied from a healthy disk to a replacement for any failed disk.

A

Striped Array

(RAID 0) is NOT faulttolerant. The failure of one drive will result in the loss of all data in the array. It is designed to increase disk performance by spreading the I/O load across the channels and drives.

7

Downloaded from LpManual.com Manuals

Setting Up SATA RAID Mode 7 - 3

7

Modules

SATA RAID Setup Procedure (BIOS)

1.

Start-up your notebook computer and press <F2> to enter the BIOS.

2.

Go to the Advanced menu, select "SATA Mode Selection" and press Enter (see page

5 - 8

).

• Select “RAID”.

3.

Press Esc and go to the Boot menu.

4.

Set the DVD-ROM Drive (make sure the Microsoft Windows 7 OS DVD is inserted) as the first device in the boot order from the Boot menu (see

“Boot

Menu” on page 5 - 15

).

5.

Select Exit Saving Changes from the Exit menu (or press F10 and Enter) and press Enter to exit the BIOS and reboot the computer.

6.

See the instructions in

“RAID Setup (Intel Matrix)” on page 7 - 5

.

Modules

RAID Setup (Intel Matrix)

1.

As the computer starts up press Ctrl + i to enter RAID configuration menu.

Figure 7 - 1

Intel(R) Rapid

Storage Technology

Option ROM

2.

Select 1.Create RAID Volume and press Enter.

3.

Type the RAID volume name and then press Tab or Enter to advance to the next field.

4.

Specify (use the up and down arrow keys) the RAID level (RAID 0, RAID 1, RAID

5 or Recovery - see

Table 7 - 1, on page 7 - 3

) and then press Tab or Enter to advance to the next field.

Downloaded from LpManual.com Manuals

Recovery Level

When selecting disks for the Recovery RAID level you will need to use the

Tab key to select a Mas-

ter disk, and the Space key to select a Recov-

ery disk.

You can select the synchronization between the disks to be Continu-

ous (automatic) or On

Request (manually).

Setting Up SATA RAID Mode 7 - 5

7

7

Modules

Recovery Level

When selecting disks for the Recovery RAID level you will need to use the

Tab key to select a Mas-

ter disk, and the Space key to select a Recov-

ery disk.

You can select the synchronization between the disks to be Continu-

ous (automatic) or On

Request (manually).

5.

Press Enter and the system will select the physical disks to use.

6.

Press Enter and select (if applicable) the Strip Size (best set to default).

7.

Press Enter and select the Capacity size (best set to default).

8.

Press Enter to select Create Volume.

9.

Press Enter to create the volume, and confirm the selection by pressing Y.

10. This will now return to the main menu.

Figure 7 - 2

RAID Created

11. Select 5.Exit and press Enter, then press Y to exit the RAID configuration menu.

12. Make sure the Windows 7 OS DVD is in the DVD drive. and as the computer starts up it will automatically boot from the Windows 7 OS DVD.

13. Press Enter to continue installing the operating system as normal (see your

Windows documentation if you need help on installing the Windows OS).

14. Install the Windows drivers from the Device Drivers & Utilities + User’s Manual disc as per

Table 4 - 1, on page 4 - 3

(make sure you install the Intel Rapid

Storage Technology driver - see

“IRST Driver Installation” on page 7 - 8

).

Modules

7

Downloaded from LpManual.com Manuals

Setting Up SATA RAID Mode 7 - 7

7

Modules

Intel Rapid Storage Technology

The Intel Rapid Storage Technology application provides high-performance

SATA and SATA RAID capabilities. Install the Intel Rapid Storage Technology

application to support your RAID system or SATA drive if set up in AHCI mode in the BIOS (see

“SATA Mode (Advanced Menu)” on page 5 - 9

).

IRST Driver Installation

1.

Insert the Device Drivers & Utilities + User’s Manual disc into the CD/

DVD drive.

2. Click Option Drivers (button).

3.

Click 4.Install IRST Driver > Yes.

4. Click Next > Next > Yes > Next > Next.

5. Click Finish to restart the computer (you will need to restart the system again after the computer has rebooted).

See the following pages for more information if you have set your hard disks up in a RAID configuration.

Modules

Intel® Rapid Storage Technology for RAID Systems

Intel® Rapid Storage Technology application displays status information on your

RAID configuration. Run the Intel® Rapid Storage Technology application from the Intel item in the All Programs menu.

When the Intel® Rapid Storage Technology application is launched the system will open the Status window. Here you can view the general health of the storage system. Various volume creation and management options are available depending on the system’s status.

Figure 7 - 3

Intel

®

Rapid

Storage Technology

Status

7

Downloaded from LpManual.com Manuals

Intel Rapid Storage Technology 7 - 9

7

Modules

Table 7 - 2

RAID Verification &

Repair Status

RAID Volume Data Verification and Repair

The RAID volume data verification process identifies any inconsistencies or bad data on a RAID 0 or RAID 1 volume. The table outlines what occurs for each RAID level:

RAID

Level

Verify Verify & Repair

RAID 0

RAID 1

Bad blocks are identified.

Bad blocks are identified.

Data on the mirrored drive is compared to data on the source drive.

N/A

Bad blocks are reassigned.

If the data on the mirrored drive does not match the data on the source drive, the data on the mirrored drive is overwritten by the data on the source.

RAID 5

Bad blocks are identified.

Parity is recalculated and compared to the stored parity for that stripe.

Bad blocks are reassigned.

If the newly calculated parity does not match the stored parity, the stored parity is overwritten with the newly calculated parity.

Replacing and Reverting Recovery and Master Volumes

If a master or recovery drive fails you will need to add a new identical drive and rebuild the recovery volume to the drive. You can also revert the master drive to the state of the previous volume update. For details on how to do this see

“Intel® Rapid

Storage Technology Help” on page 7 - 11

.

See over for details on how to verify and repair RAID volume data.

Modules

Intel® Rapid Storage Technology Help

If a hard drive member of a RAID volume is reported as “Degraded” or “Failed” it may be possible to recover the volume. If the volume cannot be restored then you will need to recreate the RAID volume and restore the data from a back up. Click the

Help menu (or press F1) for instructions on how to recover or recreate RAID Volumes.

Downloaded from LpManual.com Manuals

Help

Click the Help (or press F1) menu button at the top of the Intel®

Rapid Storage Tech-

nology application.

Click Contents to view the general list of subjects covered, click In-

dex or Search for a more specific help topics on a particular item.

Click More help on

this page at the bottom of any page for page specific help.

Figure 7 - 4

Intel

®

Rapid

Storage

Technology

Help

Intel Rapid Storage Technology 7 - 11

7

7

Modules

Table 7 - 3

RAID Verification &

Repair Status

RAID Volume Data Verification and Repair

The RAID volume data verification process identifies any inconsistencies or bad data on a RAID 0 or RAID 1 volume. The table outlines what occurs for each RAID level:

RAID Level Verify Verify & Repair

RAID 0

RAID 1

Bad blocks are identified.

Bad blocks are identified.

Data on the mirrored drive is compared to data on the source drive.

N/A

Bad blocks are reassigned.

If the data on the mirrored drive does not match the data on the source drive, the data on the mirrored drive is overwritten by the data on the source.

RAID 5

Bad blocks are identified.

Parity is recalculated and compared to the stored parity for that stripe.

Bad blocks are reassigned.

If the newly calculated parity does not match the stored parity, the stored parity is overwritten with the newly calculated parity.

Replacing and Reverting Recovery and Master Volumes

If a master or recovery drive fails you will need to add a new identical drive and rebuild the recovery volume to the drive. You can also revert the master drive to the state of the previous volume update. For details on how to do this see the help file

“Intel® Rapid Storage Technology Help” on page 7 - 11

. See over for details on

how to verify and repair RAID volume data. Verification will identify and repair data inconsistencies on the volume.

Modules

Verifying and Repairing RAID Volume Data

1.

Before verifying the volume data you will need to initialize the volume.

2.

Run the Intel® Rapid Storage Technology application from the Intel item in the

Programs/All Programs menu.

3.

Click Manage and click Advanced.

4.

Click Initialize and click Yes (button) to begin the process.

5.

The completion percentage will be listed under Status.

Figure 7 - 5

Intel

®

Rapid

Storage

Technology

Initialize

7

Downloaded from LpManual.com Manuals

Intel Rapid Storage Technology 7 - 13

Modules

6.

Click Advanced and click Verify, then click Verify (button) to begin the process.

7.

The completion percentage will be listed under Status (verifying and repairing).

7

Figure 7 - 6

Intel

®

Rapid

Storage

Technology

Verify

Modules

Wireless LAN Module

If you have included an Intel® Wireless LAN module or 3rd Party 802.11b/g/n

WLAN module in your purchase option, make sure that the Wireless LAN module is on before installing the driver.

Use the Fn + F11 key combination or Touch Sensor Instant Key to toggle power to the Wireless LAN module. When the WLAN module is powered on, the touch sensor LED will be highlighted and the indicator will briefly be displayed.

Make sure you install the drivers in the order indicated in

Table 4 - 1, on page 4 - 3

.

The operating system is the default setting for Wireless LAN control in Windows 7.

Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo module.

Wireless Device

Operation Aboard

Aircraft

The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.

Use the Fn + F11 key combination/Touch Sensor Instant key to toggle power to the WLAN module, and check the LED to see if the module is powered on or not (see

Table 1 - 4, on page 1 - 10

/

Table 1 - 3, on page 1 - 8

).

7

Downloaded from LpManual.com Manuals

Wireless LAN Module 7 - 15

7

Modules

Intel(R) PROSet/

Wireless

Access the Intel PRO-

Set Wireless tools (Statistics and Diagnostic tools) from the Start menu (Start > Programs/All Programs >

Intel PROSet Wire-

less). These tools provide diagnostic and statistical information only (use the WLAN control in Windows to connect to a WLAN access point).

Intel® Wi-Fi Link Series Driver Installation

If you see the message “Found New Hardware” click Cancel to close the window.

1.

Make sure the module is powered on, then insert the Device Drivers & Util-

ities + User’s Manual disc into the CD/DVD drive.

2. Click Option Drivers (button).

3. Click 1.Install WLAN Driver > Yes.

4. Click Next > Next.

5. Click the button to accept the license and click Next.

6. Click Next > Next > Finish.

Note: The operating system is the default setting for Wireless LAN control in Win-

dows (see overleaf).

802.11b/g/n Driver Installation

1.

Make sure the module is powered on, then insert the Device Drivers & Util-

ities + User’s Manual disc into the CD/DVD drive.

2.

Click

Option Drivers

(button).

3. Click 1.Install WLAN Driver > Yes.

4. Choose the language you prefer and click Next.

5. Click Next > Install.

6. Click Finish to restart the computer.

Note: The operating system is the default setting for Wireless LAN control in Win-

dows 7 (see overleaf).

Modules

Connecting to a Wireless Network in Windows 7

Make sure the Wireless LAN module is turned on.

1.

Click the taskbar wireless icon , and then double-click an access point to connect to or click to Open Network and Sharing Center if you do not see a network you want to connect to in the taskbar menu (a list of options will appear allowing setting changes, and creating a new network).

Network and

Sharing Center

You can also use the Net-

work and Sharing Cen-

ter control panel in

Windows (Network and

Internet) to connect to any available wireless networks.

7

Figure 7 - 7

Click Taskbar Icon

Menu & Network and Sharing Center

Downloaded from LpManual.com Manuals

Wireless LAN Module 7 - 17

Modules

7

Figure 7 - 8

Network Location

Set

2.

You may need to enter a security key for any access point to which you are trying to connect.

3.

Click to select a network location (e.g. Home, Work or Public).

4.

Click “View or change settings in Network and Sharing Center” to access further options for the connection.

5.

Click the taskbar icon to see any currently connected networks.

6.

To disconnect from the wireless network you can click the taskbar wireless icon , click the active connection and then click Disconnect (button).

Modules

Security Enabled

Networks

You should try to make sure that any network you are connecting to is a secure network.

Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.

7

Figure 7 - 9

Click Taskbar Icon

Menu - Disconnect

Downloaded from LpManual.com Manuals

Wireless LAN Module 7 - 19

7

Modules

Intel® My WiFi Help

To get help on Intel®

My WiFi configuration and settings, access the

Intel® My WiFi Utility

from the Start menu

(Start > Programs/All

Programs > Intel PRO-

Set Wireless > Intel My

WiFi Technology), or by clicking the taskbar icon

. Click the Help icon

and select a help topic from the Con-

tents menu.

Intel

®

My WiFi Configuration

Intel® My WiFi Technology uses your WLAN (for Intel WLAN modules only) module to allow you to connect up to eight other WiFi enabled devices (e.g. digital cameras, other computers, cell phones, handheld devices etc.) to your computer

(similar to Bluetooth), while still connecting to the Internet through your WiFi wireless connection. Intel® My WiFi Technology offers greater range and speed than other personal area networks, and does not require an access point.

Modules

Intel® My WiFi Configuration

You can configure the My WiFi settings as follows.

1.

Access the Intel® My WiFi Utility from the Start menu (Start > Programs/All

Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by doubleclicking the taskbar icon .

2.

Click Enable devices listed).

Figure 7 - 10

Intel® My WiFi

Utility

7

Downloaded from LpManual.com Manuals

Wireless LAN Module 7 - 21

Modules

3.

Click Start and click Control Panel.

4.

Click Network and Sharing Center (Network and Internet).

5.

Click Change adapter settings.

7

Figure 7 - 11

Network and

Sharing Center

Click Change

adapter settings

6.

Right-click Wireless Network Connection and select Properties.

Right-click Wireless Network

Connection and select Proper-

ties.

Modules

Figure 7 - 12

Network

Connections

7

Downloaded from LpManual.com Manuals

Wireless LAN Module 7 - 23

7

Modules

Figure 7 - 13

Wireless Network

Connection

Properties -

Sharing

7.

Click Sharing (tab) and select Allow other network users to connect through

this computer’s Internet connection”.

8.

Select Wireless Network Connection under Home networking connection.

9.

Click OK.

Click “Allow other network

users to connect through this computer’s Internet

connection”.

Select Wireless Network

Connection.

10. Access the Intel® My WiFi Utility from the Start menu (Start > Programs/All

Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by doubleclicking the taskbar icon .

11. Click Profiles .

Modules

Figure 7 - 14

Intel® My WiFi

Utility - Profiles

7

Downloaded from LpManual.com Manuals

Wireless LAN Module 7 - 25

7

Modules

12. Click Profiles, click Intel Wireless PAN and click Edit or New (Note that all

preset settings may not be editable - see sidebar).

Figure 7 - 15

Profiles

Profile Settings

Profiles that are preset

may not be fully edit-

able. To edit all the profile settings, click

New to create a new profile and adjust the settings to your preferences.

Figure 7 - 16

Intel® My WiFi

Profile Settings -

General

13. You can change the Profile Name and Network Name to your personal preferences in General (tab).

Profile and Network Names

The Profile Name is the name as displayed on your computer in the Net-

work Connections control panel

(see

Figure 7 - 17 on page 7 - 27

).

The Network Name (SSID) is the name the devices see when they try to connect to your computer.

Modules

14. Click Security (tab).

15. Change the Security Type to WEP and the Encryption Type to 64bit.

16. Enter a password (8 characters long) in the Password box.

Downloaded from LpManual.com Manuals

Figure 7 - 17

Intel® My WiFi

Profile Settings -

Security

7

Wireless LAN Module 7 - 27

Modules

17. Click Sharing (tab).

18. It is recommended that the Filter Network Traffic and DHCP and DNS Server are Disabled.

7

Figure 7 - 18

Intel® My WiFi

Profile Settings -

Sharing

19. Click Advanced (tab).

20. It is recommended that the Default Channel is set to Channel 1, 6 or 11.

21. Click OK to save the settings.

Modules

Figure 7 - 19

Intel® My WiFi

Profile Settings -

Advanced

7

Downloaded from LpManual.com Manuals

Wireless LAN Module 7 - 29

7

Modules

Figure 7 - 20

Wireless Network

Connection Details

22. Double-click Wireless Network Connection in Network Connections.

23. Click Details to display the Network Connection Details.

24. Access the Intel® My WiFi Utility from the Start menu (Start > Programs/All

Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by clicking the taskbar icon .

25. To add a new device follow the instructions in the devices’ user guide for connecting to a WiFi network.

26. Click Add New Device in Intel® My WiFi Utility to confirm the security settings detail.

Modules

Figure 7 - 21

Intel® My WiFi

Utility

(Add New Device)

7

Downloaded from LpManual.com Manuals

Wireless LAN Module 7 - 31

Modules

7

Figure 7 - 22

Windows Mobility

Center

Windows Mobility Center

The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc.

To access the Windows Mobility Center:

1.

Click Start, and click Control Panel (or point to Settings and click Control

Panel).

2.

Double-click Windows Mobility Center (Mobile PC).

3.

Click the button to Turn wireless off/on, or click the icon to access the network menu.

Modules

PC Camera Module

Before installing the driver, make sure the PC Camera is on. Use the Fn + F10 key

combination or Touch Sensor Instant Key to toggle power to the to the PC Camera module. When the PC Camera module is powered on, the touch sensor LED will be highlighted and the indicator will briefly be displayed.

Make sure you install the drivers in the order indicated in

Table 4 - 1, on page 4 - 3

.

There are a number of different camera modules available with this computer model series. You will have the appropriate application installed for your camera (note that some versions of the camera application do not support the zoom function). Make

sure you access the application via the desktop shortcut.

PC Camera Application and Power-Saving States

If the computer enters Sleep or Hibernate mode while running the camera application, the program will stop running, and will need to be restarted when the system resumes from the power-saving state.

Latest PC Camera

Driver Information

Check the Device Drivers

& Utilities + User’s Manu-

al disc and any accompanying insert pages, for the latest updated information on the PC Camera driver, which may override the information provided here.

PC Camera Display

The PC Camera application software needs to be run while the default note-

book LCD is the selected display device.

After a camera picture is obtained on the default notebook LCD, you may then use the Fn + F7 to toggle through the display modes (give the screen time to refresh).

7

Downloaded from LpManual.com Manuals

PC Camera Module 7 - 33

7

Modules

PC Camera Driver Installation

1.

Insert the Device Drivers & Utilities + User’s Manual disc into the CD/

DVD drive.

2. Click Option Drivers (button).

3. Click 2.Install WebCam Driver > Yes.

4. Choose the language you prefer and click Next > Next > Finish.

5. Run the camera application program from the desktop shortcut (if the hardware is turned off use the Fn + F10 key combination to turn it on again).

PC Camera Audio Setup

If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows.

1.

Click Start, and click Control Panel (or point to Settings and click Control Panel).

2.

Click Sound (Hardware and Sound).

3.

Click Recording (tab).

4.

Right-click Microphone (Realtek High Definition Audio) and make sure the item is not disabled.

5.

Double-click Microphone (or select Properties from the right-click menu).

6.

Click Levels (tab), and adjust the Microphone and Microphone Boost sliders to the level required.

7.

Click OK and close the control panels.

8.

Run the camera application program from the desktop shortcut.

9.

Go to the Devices menu heading and select Microphone (Realtek....) (it should have a tick alongside it).

10. Go to the Capture menu heading and select Capture Audio (it should have a tick alongside it).

Modules

7

Downloaded from LpManual.com Manuals

PC Camera Module 7 - 35

7

Modules

Figure 7 - 23

Audio Setup for PC

Camera

Right-click

Modules

Camera Application

The camera application is a video viewer for general purpose video viewing and testing, and for capturing video files to .avi format.

1.

Run the camera application from the desktop shortcut (it is recommended that you

set the capture file before the capture process - see below).

2.

Go to the Capture menu heading (if you wish to capture audio check

“PC Camera

Audio Setup” on page 7 - 35

) and select Start Capture.

3.

Click OK/Yes (the file location will be displayed in the pop-up box) to start capturing the video, and press Esc to stop the capture (you can view the file using the Windows Media Player).

Set Capture File

Prior to capturing video files you may select the Set Capture File... option in the

File menu, and set the file name and location before capture (this will help avoid accidentally overwriting files). Set the name and location then click Open, then set the

"Capture file size:"

and click OK. You can then start the capture process as on the previous page.

Note the important information in

“Reducing Video File Size” on page 7 - 38

in order to save file space, and help prevent system problems.

Pre-Allocating File

Size/Space

You may pre-allocate the file size (File > Allocate

File Size/Space) for the capture file in the camera program (you may need to set a folder location first).

Pre-allocating space on the hard disk can improve the capture quality (particularly of large capture files), by reducing the amount of work the hard disk has to do in finding space for the video data as it is being captured.

See also

“Reducing Video File Size” on page 7 -

38

.

7

Downloaded from LpManual.com Manuals

PC Camera Module 7 - 37

7

Modules

Reducing Video File Size

Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My

Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.

Note that the Windows system requires a minimum of 15GB of free space on the C:

drive system partition. In order to prevent system problems it is recommended that you save the captured video file to a location other than the C: drive (see

“Set Capture File” on page 7 - 37

), limit the file size of the captured video (see

“Pre-Allocating File Size/Space” on page 7 - 37

) or reduce video resolution (see below).

To Reduce Video Resolution Output Size:

1.

Run the camera application program from the desktop shortcut.

2.

Go to Options and scroll down to select Video Capture Pin....

3.

Click the Output Size drop box and select a lower resolution size in order to reduce the captured file size.

4.

Click OK.

Modules

Eliminating Screen Flicker

If you find that the video screen in the camera program is flickering, you can try to adjust the setting in the Video Capture Filter options.

1.

Run the camera application from the desktop shortcut.

2.

Go to Options and scroll down to select Video Capture Filter....

3.

Click either 50Hz or 60Hz under Frequency (Anti Flicker).

Latest PC Camera

Driver Information

Check the Device Driv-

ers & Utilities + User’s

Manual disc, and any accompanying insert pages, for the latest updated information on the

PC Camera driver, which may override the information provided here, including the figures pictured here.

7

Figure 7 - 24

Video Capture Filter

Downloaded from LpManual.com Manuals

PC Camera Module 7 - 39

7

Modules

Snapshot Folder

The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture.

If you accidentally delete or move the folder, you can create a new

Snapshot folder on the desktop in order to capture the files.

Taking Still Pictures

The camera application allows you to take still pictures.

1.

Run the camera application from the desktop shortcut.

2.

Go to Options and select Take Picture.

3.

The picture (in JPEG format) will be placed in the Snapshot folder desktop.

on the

Modules

TV Tuner Module

If your purchase configuration includes the optional Hybrid (Analog & Digital)

USB Mini-Card TV Tuner module, you will be supplied with a remote control unit and appropriate antenna and fittings for the module. Software support for the TV

Tuner module is provided by Windows Media Center in Windows 7 (not included

in Starter or Home Basic versions). A driver is provided on the

Device Drivers &

Utilities + User’s Manual disc for the remote control supplied with the TV Tuner.

The optional TV Tuner allows you to watch TV, play music CDs, video conference and capture still images and video on your PC.

The Cable (CATV) antenna will only be enabled when a TV Tuner module is

installed. Make sure you connect the TV antenna.

TV Antenna

The TV antenna supplied with any TV Tuner module is intended for indoor use only. Please do not use your TV Tuner module outdoors.

TV Tuner Remote

Point the remote at the consumer IR transceiv-

er to change channels etc.

7

Figure 7 - 25

TV Tuner Ports/

Jacks

1.

Consumer Infrared Transceiver

2.

CATV Antenna

Jack

2

1

Downloaded from LpManual.com Manuals

TV Tuner Module 7 - 41

7

Modules

TV Tuner Module

Support

Note that the TV Tuner module options in Win-

dows 7 is supported by the Windows Media

Center software which comes built-in to all the

Windows 7 versions except Starter and

Home Basic.

If your purchase includes a TV Tuner option, and you are reconfiguring your system for a different system, you should install any

Windows 7 version except Starter and Home

Basic.

Consumer Infrared Driver

1.

Insert the Device Drivers & Utilities + User’s Manual disc into the CD/

DVD drive.

2. Click Option Drivers (button).

3. Click 3.Install CIR Driver > Yes.

4. Choose the language you prefer and click Next > Next.

5. Click Finish to restart the computer.

Windows Media Center

1.

This TV Tuner module is fully supported by Windows Media Center in

Windows 7 ( not included in Starter or Home Basic versions

).

2. Run Windows Media Center directly from the Start menu (Start > Pro-

grams > Windows Media Center).

3. Windows Help and Support provides information on the Windows Media type “Media Center” in the Search Help box and click the magnifying glass icon to bring up the results.

Modules

Digital TV Broadcast Signal

The antenna is the most crucial factor in receiving a clear digital terrestrial TV broadcast signal. The passive antenna provided should provide a clear signal when placed beside a window. If the signal is not clear then you can purchase an active antenna (it should also be placed beside a window) to improve the signal. You should also check with any related government website which provides information on digital terrestrial TV coverage for your area. Note that (unlike standard analog

TV) if the digital signal is weak then no picture will appear on the TV at all.

TV Recording and Power Plans

If you intend to use the optional TV Tuner to record live TV, then go to the Power

Options control panel and create a power plan (see

“Power Plans” on page 3 - 4

) to prevent the power saving options from adjusting the computer’s performance level.

Remote Control Unit

The remote control unit allows you to remotely start and send the system into a power saving state, to run Windows Media Center and to navigate the Media Center menus etc. The remote control unit also gives full control over all TV and video functions.

CATV Cable Safety

Make sure that your

CATV system installer has connected the Coaxial cable shield to the grounding system of the building, as close to the point of cable entry as practical.

This reminder is provided to call the CATV system installer’s attention to Article 820-93 of the

NEC (Section 54, Part I of the Canadian Electrical Code).

7

Downloaded from LpManual.com Manuals

TV Tuner Module 7 - 43

7

Modules

Wireless Device

Operation Aboard

Aircraft

The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.

Use the Fn + F12 key combination to toggle power to the Bluetooth module, and check the LED to see if the module is powered on or not (see

Table 1 - 4, on page 1 - 10

/

Table 1 - 3, on page 1 - 8

).

Note that you need to install both the WLAN

& Bluetooth drivers for the WLAN & Bluetooth Combo module.

Bluetooth Module

The optional Bluetooth module allows you to connect your computer to Bluetooth enabled devices such as other computers, desktop computers, mobile phones, printers, digital cameras, PDAs, headsets etc. using a short-range radio frequency.

If your purchase option includes the Combination Wireless LAN & V3.0 Blue-

tooth module (either Intel® Centrino Advanced-N 6230 or 3rd Party) then install the driver as instructed below:

• For 3rd party Bluetooth modules see the installation procedure see

“3rd Party

Bluetooth Combo Driver Installation” on page 7 - 46

and

“3rd Party Bluetooth & WLAN Combo Settings” on page 7 - 47

.

• For Intel Bluetooth modules see the installation procedure see

“Intel Bluetooth Combo Driver Installation” on page 7 - 54

and

“Bluetooth Configuration in Windows 7” on page 7 - 55

.

If your purchase option includes the standalone V2.1 Bluetooth module then no driver is required and you can configure the settings as per the instructions in

“Bluetooth Configuration in Windows 7” on page 7 - 55

.

Use the Fn + F12 key combination or Touch Sensor Instant Key to toggle power to the Bluetooth module. When the Bluetooth module is powered on, the touch sensor LED will be highlighted and the indicator will briefly be displayed.

Bluetooth Data Transfer

Note that the transfer of data between the computer and a Bluetooth enabled device is supported in

one direction only (simultaneous data transfer is not supported). Therefore if you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the Bluetooth enabled device to your computer until the file transfer process from the computer has been completed.

Bluetooth Module & Resuming From Sleep Mode

The Bluetooth module’s default state will be off after resuming from the Sleep power-saving state. Use the key combination (Fn + F12) to power on the Bluetooth module after the computer resumes from

Sleep.

Modules

7

Downloaded from LpManual.com Manuals

Bluetooth Module 7 - 45

7

Modules

High Speed Bluetooth

Data Transfer

The Combination Wire-

less LAN & V3.0 Blue-

tooth module supports high speed (V3.0) data transfer. However to achieve such transfer speeds, both devices

must support high

speed data transfer.

To obtain high speed

(V3.0) data transfer make sure that both the

WLAN and Bluetooth modules are powered on.

Check your Bluetooth compatible device’s documentation to confirm it supports high speed data transfer.

3rd Party Bluetooth Combo Driver Installation

Note this driver is required only for the combo Bluetooth and WLAN module only.

1.

Before installing the driver make sure the Bluetooth module is powered

on (use Fn + F12 key combination), then insert the Device Drivers & Utili-

ties + User’s Manual disc into the CD/DVD drive. If a Found New Hard-

ware window appears, click Cancel in all windows that appear, and then proceed to install the driver as below.

2.

Click

Option Drivers

(button).

3. Click 6.Install Combo BT Driver > Yes.

4. Choose the language you prefer and click OK.

5. Click Next.

6. Click the button to accept the license and click Next.

7. Click Next > (select if you want to create an icon to appear on the desktop)

Next > Install.

8. Click Finish.

9. The My Bluetooth icon will appear on the desktop and the Bluetooth item will be installed in the Programs/All Programs menu.

10. See overleaf for information on Bluetooth networking.

Modules

3rd Party Bluetooth & WLAN Combo Settings

This information applies to the combo Bluetooth and WLAN module only.

1.

Make sure the Bluetooth module is powered on.

2.

Double-click the My Bluetooth application on the desktop (or access Bluetooth from the Programs/All Programs menu).

3.

Click My Bluetooth Settings (menu heading).

Bluetooth Module &

Resuming From Sleep

Mode

The Bluetooth module’s default state will be off after resuming from the Sleep power-saving state. Use the key combination (Fn + F12) to power on the Bluetooth module after the computer resumes from Sleep.

7

Figure 7 - 26

My Bluetooth

Settings

Downloaded from LpManual.com Manuals

Bluetooth Module 7 - 47

Modules

4.

Click General Settings to change the computer name that other Bluetooth

devices will see, and click the tickbox to Allow Bluetooth devices to find this

computer

5.

Click OK to confirm the settings.

7

Figure 7 - 27

General Settings

6.

Click File Transfer Settings to Enable sharing of my files with other

Bluetooth devices.

7.

Click OK to confirm the settings.

Modules

Figure 7 - 28

File Transfer

Settings

7

Downloaded from LpManual.com Manuals

Bluetooth Module 7 - 49

Modules

Bluetooth Networking Setup

This information applies to the combo Bluetooth and WLAN module only.

1.

Make sure the Bluetooth module is powered on.

2.

Double-click the My Bluetooth application on the desktop (or access it from the

Programs/All Programs menu).

3.

Click My Bluetooth Settings (see

Figure 7 - 26 on page 7 - 47

).

7

Figure 7 - 29

Network Settings

4.

Click Network Settings (make sure the Bluetooth module is powered on.

5.

Click Enable Bluetooth Network and click OK.

6.

A message will appear in the notification area to confirm that the network driver has been installed.

Bluetooth & WLAN Combo Module Configuration

Setup your Bluetooth Device so the Computer Can Find it

1.

Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on.

2.

Make the device discoverable (to do this check your device documentation).

To Turn the Bluetooth Module On

1.

Press the Fn + F12 key combination to power on the Bluetooth module.

To Add a Bluetooth Device

1.

Double-click the My Bluetooth application on the desktop (or access it from the

Programs/All Programs menu).

2.

Double-click the device you want to pair with the computer (if no devices appear press F5 or click the Refresh button to search for devices).

Modules

Bluetooth Module &

Resuming From Sleep

Mode

The Bluetooth module’s default state will be off after resuming from the Sleep power-saving state. Use the key combination (Fn + F12) to power on the Bluetooth module after the computer resumes from Sleep.

7

Figure 7 - 30

My Bluetooth

Devices

Downloaded from LpManual.com Manuals

Bluetooth Module 7 - 51

Modules

3.

You will then be presented with a menu of options to select from.

7

Figure 7 - 31

Bluetooth Device

Options

4.

Click the appropriate button to connect to the device.

5.

You may need to allow the connection from your device, and you will then need to provide a passcode from the device.

6.

You can then enter the passcode on the computer and click OK to establish the connection.

Modules

Figure 7 - 32

Bluetooth Pairing

Code & Connection

Established

7

Downloaded from LpManual.com Manuals

Bluetooth Module 7 - 53

7

Modules

High Speed Bluetooth

Data Transfer

The Combination Wire-

less LAN & V3.0 Blue-

tooth module supports high speed (V3.0) data transfer. However to achieve such transfer speeds, both devices

must support high

speed data transfer.

To obtain high speed

(V3.0) data transfer make sure that both the

WLAN and Bluetooth modules are powered on.

Check your Bluetooth compatible device’s documentation to confirm it supports high speed data transfer.

Intel Bluetooth Combo Driver Installation

Note this driver is required only for the Intel combo Bluetooth and WLAN module only.

1.

Before installing the driver make sure the Bluetooth module is powered

on (use Fn + F12 key combination), then insert the Device Drivers & Utili-

ties + User’s Manual disc into the CD/DVD drive. If a Found New Hard-

ware window appears, click Cancel in all windows that appear, and then proceed to install the driver as below.

2.

Click

Option Drivers

(button).

3. Click 4.Install Combo BT Driver > Yes.

4. Click Next > Next.

5. Click the button to accept the license and click Next.

6. Click Next > Finish.

7. See over for configuration instructions.

Note that, at the time of going to press, Intel® Centrino Advanced 6230 WLAN &

Bluetooth V3.0+HS combo modules use the standard Bluetooth configuration in

Windows 7 (see

“Bluetooth Configuration in Windows 7” on page 7 - 55

). Do not

use the Bluetooth & WLAN Combo settings information outlined from page

7 - 47

to page

7 - 53

. See also

“Intel® WLAN & Bluetooth V3.0+HS Combo Modules” on page 8 - 19

.

Modules

Bluetooth Configuration in Windows 7

Setup your Bluetooth Device so the Computer Can Find it

1.

Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on.

2.

Make the device discoverable (to do this check your device documentation).

To Turn the Bluetooth Module On

1.

Press the Fn + F12 key combination to power on the Bluetooth module.

2.

A Bluetooth icon will appear in the taskbar.

3.

You can then do any of the following to access the Bluetooth Devices control panel.

Double-click the taskbar icon to access the Bluetooth Devices control panel.

Click/Right-click the taskbar icon and choose an option from the menu.

Add a Device

Click Start, and click

Control Panel and then click

Devices and

Printers (Hardware

and Sound). Click Add

a device to search for any available Bluetooth devices.

If you are experiencing problems connecting to some Bluetooth devices

see

“” on page 8 - 14

.

7

Figure 7 - 33

Bluetooth Devices &

Click Icon Menu

Add a device

Right-Click Taskbar Icon

Downloaded from LpManual.com Manuals

Bluetooth Module 7 - 55

7

Modules

Pairing Options

If a device has been previously connected then the pairing option menu will appear when you attempt subsequent connections. You can choose to have the computer create a pairing code for you, use the device’s existing pairing code or you can pair certain devices without using a code.

To Add a Bluetooth Device

1.

Access the Bluetooth Devices control panel and click Add a device.

2.

Double-click the device you want to pair with the computer.

Figure 7 - 34

Add a Device

3.

On first connection the computer will provide you with a pairing code to be entered onto the device.

Modules

4.

Enter the code into your Bluetooth enabled device and follow any on-screen instructions to complete the pairing.

Pairing Codes

The example outlined here shows a connection to a mobile device. Other devices e.g. computers, may have a slightly different connection procedure, and may require you to confirm a pairing code is correct on both devices. Follow the onscreen instructions to complete the pairing.

5.

Windows will check to see if any drivers are required to complete the pairing.

6.

Follow any on-screen instructions on the computer if device drivers are required to be installed.

7.

Click Close.

Figure 7 - 35

Pairing Code

Example

7

Figure 7 - 36

Pairing Complete &

Bluetooth Device

Enabled

Downloaded from LpManual.com Manuals

Bluetooth Module 7 - 57

7

Modules

Bluetooth Help

To get help on Bluetooth configuration and settings, select Help and

Support from the Start menu. Type Bluetooth in the Search Help box, and select an item from the returned search results to get more information.

To Change Settings for the Bluetooth Device

1.

Click the taskbar icon and select Show Bluetooth Devices.

2.

Right-click on the device you want to change and click Properties to:

• Change the name of the device (click Bluetooth, type a new name and click OK).

• Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK).

To Make your Computer Discoverable to Bluetooth Devices

1.

Click the taskbar icon and select Open Settings.

2.

Click Options, and make sure that Allow Bluetooth devices to find this

computer check box (Discovery) has a tick inside it.

3.

Make sure that the Alert me when a new Bluetooth device wants to connect check box (Connections) has a tick inside it, if you want to be notified when a

Bluetooth device wants to connect.

Figure 7 - 37

Bluetooth Settings -

Options

Modules

Security Modules (Fingerprint & TPM)

The encrypted channel between the Trusted Platform Module security chip and the fingerprint reader with Protector Suite Software provides a high level of security for your computer. A further level of security and control is provided in the

BIOS (see

“Security Menu” on page 5 - 13

and

“Boot Menu” on page 5 - 15

).

The fingerprint reader and Protector Suite Software allow you to:

• Access or Lock your computer

• Protect sensitive files

• Display and file your favorite web pages

• Fill in frequently used dialogs

• Run your favorite applications

The TPM security chip allows you to create and manage digital certificates for user and platform authentication. This type of security is usually administered within large enterprises and organizations, and therefore requires implementation by a system administrator before users can access security features.

Password Warning

If you set passwords for any of the security modules, NEVER forget your password.

The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.

7

Downloaded from LpManual.com Manuals

Security Modules (Fingerprint & TPM) 7 - 59

7

Modules

Password Warning

If you set passwords for any of the security modules, NEVER forget your password.

The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.

Fingerprint Reader Module

If you have included the fingerprint reader in your purchase option you will need to install the driver as per the instructions below.

Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection.

Before beginning the enrollment process it is recommended that you go through the fingerprint tutorial (see

Figure 7 - 38 on page 7 - 61

).

Fingerprint Reader Driver Installation

1.

Insert the Device Drivers & Utilities + User’s Manual disc into the CD/

DVD drive.

2. Click Option Drivers.

3. Click 7.Install FingerPrint Driver > Yes.

4. Click Next > Next > Next.

5. Click Finish > Yes to restart the computer.

6. Click the tray icon , scan a finger or click Start > Programs/All Pro-

grams > Protector Suite > Control Center and then begin the enrollment

process (see over).

Modules

User Enrollment

1.

Click Start > Programs/All Programs > Protector Suite > Control Center, or double click the taskbar icon (click Initialize).

2.

On the first run of the program you will be asked to click the Accept button to accept the license.

3.

If you have not set a Windows password you will be prompted to do so (note: If you have not set a password Protector Suite cannot secure access to your computer).

4.

Click Submit when you have entered password.

5.

You will then be prompted to enroll your fingerprints (you can click Tutorial to get help with fingerprint enrollment at any time).

Fingerprint

Enrollment

Note that it is strongly recommended that you enroll

more than one finger in case of injury etc.

Figure 7 - 38

Fingerprint

Enrollment

Tutorial

7

Downloaded from LpManual.com Manuals

Fingerprint Reader Module 7 - 61

Modules

Fingerprint

Enrollment

Note that it is strongly recommended that you enroll

more than one finger in case of injury etc.

6.

Click the button above any of the fingers to begin the enrollment process for that finger.

7.

Swipe the finger until the progress bar reaches 100% to enroll that finger.

7

Figure 7 - 39

Fingerprint

Enrollment

Progress

8.

Close the Protector Suite 2009 window.

Modules

9.

Right-click the taskbar icon and select Start Control Center (and then swipe a finger) to allow you to Edit Fingerprints, register Applications, edit Settings and access the Help menu etc. You can also run the Control Center etc. from the

Protector Suite item in the Programs/All Programs menu

10. Click “Help” to get more information on any topic.

11. You can also run the Tutorial, or Product Tour video to get more information.

Help

Figure 7 - 40

Control Center &

Biomenu

7

12. If you swipe your finger over the reader at any time you can access the Biomenu to lock the computer, register websites, access the Personal Safe, open the

Control Center and access the Help menu.

Downloaded from LpManual.com Manuals

Fingerprint Reader Module 7 - 63

7

Modules

Help

For more information on these and other features simply access “Help” in the Fingerprint Control

Center and select the item from the menu on the left.

Fingerprint Control Center Features

Application Launcher

The Application Launcher allows you to register applications to be launched when assigned to a particular finger. Simply copy the application icon on to one of the registered fingers and ten click OK to close the application window. Once registered the application will launch when you swipe the appropriate finger across the sensor.

Password Bank

The Password Bank stores registrations of user names, passwords and other settings for web sites etc.

Personal Safe

The Personal Safe is an encrypted area assigned on your hard drive that allows you to store files and folders to be protected by fingerprint protection.

Modules

Trusted Platform Module

Before setting up the TPM functions you must initialize the security platform.

Enabling & Activating TPM

1.

Restart the computer.

2.

Enter the PhoenixBIOS Setup Utility by pressing F2 during the POST.

3.

Use the arrow keys to select the TPM State menu.

4.

Select Change TPM State, and set the item to Enable & Activate.

Figure 7 - 41

TPM State

(Enable & Activate)

7

Downloaded from LpManual.com Manuals

Trusted Platform Module 7 - 65

Modules

5.

Press F10 to save the changed BIOS information, exit the BIOS and restart the computer.

6.

If you make any changes to the TPM State you will be asked to Execute/Reject the change after restart.

7

Figure 7 - 42

Physical Presence

Operations

7.

You can now install the TPM driver (see

“Trusted Platform Module (TPM)

Driver Installation” on page 7 - 67

) and then initialize the TPM.

Modules

Trusted Platform Module (TPM) Driver Installation

1.

Insert the Device Drivers & Utilities + User’s Manual disc into the CD/

DVD drive.

2. Click Option Drivers (button).

3. Click 5.Install TPM Driver > Yes.

4. Click Install > Next.

5. Click the button to accept the license and click Next.

6. Click Next > Next > Install.

7. Click Finish > Yes to restart the computer.

Initializing TPM

1.

Run the application from the Infineon Security Platform Solution > Manage

Security Platform item in the Start > Programs/All Programs menu.

2.

Click User Settings (tab) and click Yes, or right-click the icon in the notification area of the taskbar, and select Security Platform Initialization (or click the Security Platform State taskbar bubble).

3.

The Quick Initialization method will automatically be selected for you (if you need to use advanced settings provided by your network administrator then select

Advanced Initialization).

4.

You will need to use a removable media (e.g. a USB Flash Drive) to store passwords and data (keep the media in a safe place until required).

Downloaded from LpManual.com Manuals

Trusted Platform Module 7 - 67

7

Modules

5.

Select the drive you want to use from the drop-down menu and click Next.

7

Figure 7 - 43

Security Platform

Quick Initialization

Wizard

6.

Choose the Security Platform Features you want to use by clicking the appropriate tickbox.

7.

Enter a Basic User Password (and re-type to confirm it) and click Next.

Modules

Help

Right-click the icon in the notification area of the taskbar to bring up the menu to select Help or How to use

the Security Platform Fea-

tures.

You can also click the Help button in any of the Infineon

Security Platform Settings

Tool tabs to bring up specific help topics on each tab.

8.

Click Next to confirm the settings.

9.

The computer will then initialize the settings.

10. Click Finish.

11. Click the tabs and control panels to adjust the settings.

12. Double-click the taskbar icon to access the Infineon Security Platform

Settings Tool, or right-click the taskbar icon and select a menu item.

Downloaded from LpManual.com Manuals

Figure 7 - 44

Settings

Trusted Platform Module 7 - 69

7

7

Modules

Menus

Note that not all the menus pictured here will be available for access.

The menu items that appear will be dependent on your configuration settings etc. (see the Help file for full details).

Infineon Security Platform Settings Tool

The Infineon Security Platform Settings Tool allows you to manage and check the

TPM state, manage your password information, and to backup and restore the TPM data. As TPM is usually administered within large enterprises and organizations, your system administrator will need to assist you in managing the information here.

Figure 7 - 45

Infineon Security

Platform Settings

Tool

Modules

User Settings

This page allows the settings to be configured for the currently logged in Infineon

Security Platform user including the ability to change the password, configure secure e-mail, file and folder encryption and Enhanced Authentication. You can also import or delete certificates protected by the security platform.

Figure 7 - 46

Infineon Security

Platform Settings

Tool (User Settings)

7

Downloaded from LpManual.com Manuals

Trusted Platform Module 7 - 71

Modules

7

Figure 7 - 47

Infineon Security

Platform Settings

Tool (Backup)

Backup

Here you can configure backup and restore operations. Backup files contain the computer identification and user identification information which is used to match the machine name and user name with the current machine and user during restoration.

Migration

The Migration tab is used to help securely transfer keys and certificates from one platform to another.

Modules

Figure 7 - 48

Infineon Security

Platform Settings

Tool (Migration)

7

Downloaded from LpManual.com Manuals

Trusted Platform Module 7 - 73

Modules

Password Reset

Use Password Reset to reset basic user passwords when required.

7

Figure 7 - 49

Infineon Security

Platform Settings

Tool

(Password Reset)

Modules

BitLocker

BitLocker Drive Encryption can be used in conjunction with the TPM to encrypt data on the disk and is done via the Microsoft BitLocker Control Panel Applet.

Click Configure and select a drive to be encrypted and then follow the Wizard to begin the encryption process.

Figure 7 - 50

Infineon Security

Platform Settings

Tool

(BitLocker)

7

Downloaded from LpManual.com Manuals

Trusted Platform Module 7 - 75

Modules

Access the Microsoft BitLocker Drive Encryption control panel applet from the

Windows control panel (System and Security).

7

Figure 7 - 51

BitLocker Drive

Encryption

Advanced

Configure all the Security Platform owner and policy settings from the Advanced tab. The settings that can be changed are for the local computer only.

Modules

Figure 7 - 52

Infineon Security

Platform Settings

Tool

(Advanced)

7

Downloaded from LpManual.com Manuals

Trusted Platform Module 7 - 77

7

Modules

Troubleshooting

Chapter 8: Troubleshooting

Overview

Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.

If all else fails, talk to your service representative. You should also make a record of what happened and what remedies you tried.

Of course, if something goes wrong, it will happen at the most inconvenient time possible, so you should preview this section just in case. If, after you’ve tried everything, and the system still won’t cooperate, try turning it off for a few minutes and then rebooting. You will lose any unsaved data, but it may start working again. Then call your service representative.

8

Downloaded from LpManual.com Manuals

Overview 8 - 1

8

Troubleshooting

Basic Hints and Tips

Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working.

Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power Indicators (see

“LED Indicators” on page 1 - 7

) to see the computer’s power status.

Connections - Check all the cables to make sure that there are no loose connections anywhere.

Power Savings - Make sure that the system is not in Hibernate or Sleep mode by pressing the keys config-

ured in your Power Options (see

“Configuring the Power Buttons” on page 3 - 8

), the Fn + F4 key combi-

nation, or power button to wake-up the system.

Brightness - Check the brightness of the screen by pressing the Fn + F8 and F9 keys to adjust the brightness (see

Table 1 - 4, on page 1 - 10

).

Display Choice - Press Fn + F7 to make sure the system is not set to “external only” display.

Boot Drive - Make sure there are no optical media and/or USB storage devices in any connected drive when you start up your machine (this is a common cause of the message “Invalid system disk - Replace the

disk, and then press any key” / “Remove disks or other media. Press any key to restart”).

Troubleshooting

Backup and General Maintenance

• Always backup your important data, and keep copies of your OS and programs safe, but close to hand.

Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet.

• Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer. You can use those that are provided free with your OS, or buy the more powerful dedicated programs to do so.

• Write down your passwords and keep them safe (away from your computer). This is especially important if you choose to use a Boot password for the SCU (see

“Security Menu” on page 5 - 13

).

• Keep copies of vital settings files such as network, dialup settings, mail settings etc. (even if just brief notes).

8

Warranty

The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty.

Downloaded from LpManual.com Manuals

Backup and General Maintenance 8 - 3

8

Troubleshooting

Viruses

• Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini-

tions file updates are usually downloadable directly from the internet.

• Be careful when opening e-mail from sources you don’t know. Viruses are often triggered from within e-

mail attachments so take care when opening any attached file. You can configure most Anti-Virus programs to check all e-mail attachments. Note: You should also beware of files from people you know as the virus may have infected an address book and been automatically forwarded without the person’s knowledge.

• Keep a “Bootable CD-ROM/DVD-ROM/USB storage device” (this CD/DVD/USB device provides basic information which allows you to startup your computer) handy. You may refer to your OS’s documentation for instructions on how to make one, and many Anti-Virus programs will also provide such a disk (or at least instructions on how to make one).

Troubleshooting

Upgrading and Adding New Hardware/Software

• Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system.

• Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing.

• Read the documentation. We can assume, since you are reading this that you are looking at the computer’s manual, but what about any new peripheral devices you have just purchased? Many problems are caused by the installation of new hardware and/or software. Always refer to the documentation of any new hardware and/or software, and pay particular attention to files entitled “READ ME” or “READ ME FIRST”.

• When installing a new device always make sure the device is powered on, and in many cases you will need to restart the computer. Always check that all the cables are correctly connected.

• Make sure you have installed the drivers for any new hardware you have installed (latest driver files are usually available to download from vendor’s websites).

• Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs.

8

Downloaded from LpManual.com Manuals

Upgrading and Adding New Hardware/Software 8 - 5

8

Troubleshooting

• Don’t over complicate things. The less you have to deal with then the easier the source of the problem may be found; Example - if your computer has many devices plugged into its ports, and a number of programs running, then it will be difficult to determine the cause of a problem. Try disconnecting all of the devices and restarting the computer with all the peripheral devices unplugged. A process of elimination (adding and removing devices and restarting where necessary) will often find the source of a problem, although this may be time consuming.

Troubleshooting

Problems & Possible Solutions

Problem Possible Cause - Solution

You turned the power on but it doesn’t work.

The Battery LED power

Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts.

Low Battery. Plug in the AC power source. If the computer doesn’t start up immediately, turn it off then on again.

orange.

You are losing battery

power too quickly.

The system is using too much power. If your OS has a Power Options scheme (see

Plans” on page 3 - 4

device/external device that is drawing a lot of power.

“Power

) check its settings. You may also be using an ExpressCard device/USB

Actual battery operating

time is shorter than expected.

You are attempting to run an SLI configuration on battery power. Due to the high power and system demands created by enabling SLI Configuration, you should not enable SLI

configuration if your computer is powered by battery only.

The battery has not been fully discharged before being recharged. Make sure the battery is fully discharged and recharge it completely before reusing (see

“Battery Information” on page 3 -

10

).

Check the settings of any active power plan (see

“Power Plans” on page 3 - 4

).

A peripheral device/USB device is consuming a lot of power. Turn off/remove the unused device to save power.

8

Downloaded from LpManual.com Manuals

Problems & Possible Solutions 8 - 7

8

Troubleshooting

Problem Possible Cause - Solution

The computer feels too

hot.

Make sure the computer is properly ventilated and the vents/fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see

“Overheating” on page 1 - 15

). Make sure you’re using the correct adapter.

Nothing appears on

screen.

No image appears on the external monitor I have plugged in and powered on.

Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the vents/fan intakes to be blocked.

The system is in a power saving mode. Toggle the Fn + F4 (see

“Configuring the Power

Buttons” on page 3 - 8

).

\

The screen controls need to be adjusted. Toggle the screen control Fn + F8/F9 key combinations.

If you’re connected to an external monitor, make sure it’s plugged in and turned on. You should also check the monitor’s own brightness and contrast controls.

The computer is set for a different display. Toggle the screen display key Fn + F7 combination. If an external monitor is connected, turn it on.

The screen saver is activated. Press any key or touch the TouchPad.

You haven’t installed the video driver and configured it appropriately from the Control Panel. See

“NVIDIA Video Driver Controls” on page B - 1

for instructions on installing and configuring the video driver.

Troubleshooting

Problem Possible Cause - Solution

You forget the boot

password.

If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help.

Password Warning

If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.

The sound cannot be heard or the volume is very low.

The

compact disc

cannot be read.

The compact disc is dirty. Clean it with a CD-ROM cleaner kit.

The compact disc tray will not open when there is a disc in the tray.

The

DVD regional

codes can no longer be changed.

The volume might be set too low. Check the volume control in the Volume Control Panel in the

Windows taskbar, use the key combination Fn + F5 and F6 or move your finger slowly along the volume control slider to adjust the system volume (see

“Audio Features” on page 2 - 11

/

“Touch Sensor Instant Keys” on page 1 - 8

) to adjust.

The compact disc is not correctly placed in the tray. Gently try to remove the disc using the eject hole (see

“Loading Discs” on page 2 - 3

).

The code has been changed the maximum 5 times. See

“DVD Regional Codes” on page 2 - 5

.

Downloaded from LpManual.com Manuals

Problems & Possible Solutions 8 - 9

8

8

Troubleshooting

Problem Possible Cause - Solution

The TouchPad doesn’t work.

The system freezes or the screen goes dark.

The system never goes into a power saving

mode.

The

Wireless LAN/

Bluetooth/PC Camera

modules cannot be

detected.

The

Wireless LAN/

Bluetooth/PC Camera

modules cannot be

configured.

The Touchpad has been disabled. Press the Touchpad toggle (Fn + F1) key combination (make sure you have installed the Touchpad driver.

The system’s power saving features have timed-out. Use the AC/DC adapter, press a key on the keyboard, or press the sleep (Fn + F4) key combination, or press the power button if no LEDs are lit.

Power Options features are not enabled. Go to the Windows Power Options menu and enable

the features you prefer (see

“Power-Saving States” on page 3 - 6

). Make sure you have

enabled Hibernate mode from the control panel.

The modules are off. Check the appropriate LED indicator to see if the modules are on or off (see

“Touch Sensor Instant Keys” on page 1 - 8

). If the LED indicator is not illuminated, then press the appropriate touch sensor instant key/function key combination in order to enable the modules.

The driver(s) for the module(s) have not been installed. Make sure you have installed the driver for the appropriate module (see the instructions in

Chapter 7 “Modules”

for the appropriate module).

Troubleshooting

Problem Possible Cause - Solution

When a DVD is played in

Windows Media Player/

Media Center, the audio

track in other languages

(commentaries etc.) is

not clear if connected to the S/PDIF-Out Jack.

Nothing appears on the screen when the PC

Camera software is run.

This is an issue with Windows Media Player/Media Center and audio output through the S/PDIF-

Out Jack. We recommend that you use the Power DVD application to play DVDs.

A file cannot be copied to/from a connected

Bluetooth device.

The Bluetooth module is

off after resuming from

Sleep.

You have selected an external display as the default display device. The PC Camera application software needs to be run while the default notebook LCD is the selected display device.

After a camera picture is obtained on the default notebook LCD, you may then use the Fn + F7 to toggle through the display modes (give the screen time to refresh).

If you have selected an external display as your display device do not run the PC Camera software application until you have switched back to the notebook LCD.

The transfer of data between the computer and a Bluetooth enabled device is supported in one

direction only (simultaneous data transfer is not supported). If you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the Bluetooth enabled device to your computer until the file transfer process from the computer has been completed

The Bluetooth module’s default state will be off after resuming from the Sleep power-saving state.

Use the key combination (Fn + F12) to power on the Bluetooth module after the computer resumes from Sleep.

8

Downloaded from LpManual.com Manuals

Problems & Possible Solutions 8 - 11

8

Troubleshooting

Problem Possible Cause - Solution

No sound can be heard through an HDMI connected display device.

You are experiencing problems with image

distortion in a 3D game

(or any 3D program)

when the computer is

powered by the battery.

You have not configured the HDMI audio output. See

“HDMI Audio Configuration” on page 2 -

8

.

Where this is the case, install the beta video driver version provided on the Device Drivers &

Utilities +User’s Manual disc.

1.

Insert the Device Drivers & Utilities + User’s Manual disc and click Browse

CD/DVD.

2.

The driver is located in the following location on the disc:

Drivers\02Video(beta)\.

3.

Double-click the executable setup file and follow the on-screen instructions to install the driver.

Troubleshooting

Problem Possible Cause - Solution

When the battery is being used to power the system in an environment with an ambient temperature of below 10

C/50

F, the

battery reaches a low level very quickly.

This can occur as the battery cell performs poorly in a low temperature environment, especially

with a discharge rate of over 2C. Systems powered by the battery will perform normally at environmental temperatures over 10

C/50

F. To use the system at environmental temperatures below 10

C/50

F, it is recommended that the system is powered by the AC/DC adapter.

Battery Notes:

Note that when the the battery capacity is measured it may read less than the 5300mAh indicated on the label, and possibly less than 5000mAh. This can be due to either of the following factors:

• The battery capacity listed on the label is defined by cell character specification. There is a -5% capacity tolerance based on a test at 0.2C charge/0.2C discharge. Therefore

5035mAh (-5% of 5300mAh) meets the battery capacity specification listed.

• This system runs with a 0.6C charge/1C~2.5C discharge rate. The higher system charge/ discharge rate can result in a lower battery capacity measurement reading.

8

Downloaded from LpManual.com Manuals

Problems & Possible Solutions 8 - 13

8

Troubleshooting

Problem Possible Cause - Solution

You have a RAID enabled and the system will not boot to Windows.

You may need to recover the RAID volumes.

1.

As the computer starts up press Ctrl + i to enter RAID configuration menu

2.

If the RAID volume’s Physical disks are marked in red, then press 4.Recovery

Volume Options.

3.

If you cannot access 4.Recovery Volume Options (i.e. it is grayed out) then press

5.Acceleration Options.

4.

Press Enter and return to the main menu, then press 4.Recovery Volume

Options.

5.

Follow the on screen instructions to recover the Physical disks.

6.

If only one of the physical disks now appears green, then press 6.Exit to save the changes and exit and boot to Windows.

7.

When Windows is loaded run the Intel® Matrix Storage Console from the Intel®

Matrix Storage Manager in the Programs/All Programs menu.

8.

Click View > Advanced Mode.

9.

Right-click on the RAID volume and select either Verify Volume Data or Verify

and Repair Volume Data.

10. The verification or verification and repair process will run and display progress.

11. A dialog box will display the final status of the verification or verification and repair status.

Troubleshooting

Bluetooth Connection Problems

If you are experiencing problems connecting to some Bluetooth devices (in particular certain mobile phones and headsets) it maybe necessary to download and install the Windows Mobile Device Center software (for Win-

dows Vista and Windows 7). Go to the Microsoft website and search for the Microsoft Windows Device Center

Driver for Windows Vista (64-bit or 32-bit) and Windows 7 (64-bit or 32-bit), and then download the driver.

1.

Install the Microsoft Windows Device Center Driver as appropriate for your operating system.

2.

Windows Vista will automatically configure the driver for you, however Windows 7 requires further configuration.

3.

Make sure the Bluetooth device is powered on.

4.

Go the Windows 7 control panel and double-click Device Manager (Hardware and Sound > Devices and

Printers).

5.

Bluetooth Peripheral Device(s) will be listed under Other Devices (note this will only be listed if you have connected, or tried to connect to, a Bluetooth device previously).

Bluetooth Peripheral Devices

You will need to repeat the procedure listed here for all Bluetooth Peripher-

al Devices listed under Other Devices i.e. until there are no more Bluetooth

Peripheral Devices listed under this menu heading.

8

Downloaded from LpManual.com Manuals

Figure 8 - 1

- Device Manager

Bluetooth Connection Problems 8 - 15

Troubleshooting

6.

Right-click Bluetooth Peripheral Device and click on Update Driver Software.

7.

Click Browse my computer for driver software.

8.

Click Let Me pick from a list of device drivers on my computer.

8

Figure 8 - 2

- Browse my computer.../Let me pick from...

9.

Select Bluetooth Radios from the list.

Figure 8 - 3

- Select Bluetooth Radios

Troubleshooting

10. A list of drivers will appear with Manufacturer on one side and Model in the other.

11. Choose Microsoft Corporation (make sure you choose the full name Microsoft Corporation and do not choose Microsoft - Note that you must have installed the Microsoft Windows Device Center Driver for

Microsoft Corporation to appear in the list).

12. Select Windows Mobile-based device support from the Model list.

Make sure you select

Microsoft Corporation

Figure 8 - 4

- Select Device Driver

13. Click Next > Yes and the driver will install.

14. Click Close to complete the installation.

Downloaded from LpManual.com Manuals

Bluetooth Connection Problems 8 - 17

8

8

Troubleshooting

15. The Device Manager should now display the Windows Mobile-based device support under Bluetooth

Radios.

16. You will need to repeat the process for any other Bluetooth Peripheral Devices listed under Other Devices.

Figure 8 - 5

- Device Manager - Bluetooth Radio

Troubleshooting

Intel® WLAN & Bluetooth V3.0+HS Combo Modules

Note that, at the time of going to press Intel® Centrino Advanced 6230 WLAN & Bluetooth V3.0+HS combo modules use the standard Bluetooth configuration in Windows 7 (see

“Bluetooth Configuration in Windows 7” on page 7 - 55

). Do not use the Bluetooth & WLAN Combo settings information outlined from page

7 - 47

to page

7 - 53

.

Driver Release Update

Note also that, at the time of going to press, these modules do not support high speed Bluetooth (V3.0) data transfer. Intel have scheduled a driver release to allow this module to support high speed data transfer, so please check with Intel or your service center for details.

8

Downloaded from LpManual.com Manuals

Bluetooth Connection Problems 8 - 19

8

Troubleshooting

Interface (Ports & Jacks)

Appendix A: Interface (Ports & Jacks)

Overview

The following chapter will give a quick description of the ports & jacks which allow your computer to communicate with external devices, connect to the internet etc.

Downloaded from LpManual.com Manuals

Interface (Ports & Jacks) A - 1

A

A

Interface (Ports & Jacks)

Ports and Jacks

Item

Card Reader

Cable (CATV)

Antenna Jack

Description

The card reader allows you to use the following digital storage cards:

MMC (MultiMedia Card) / RSMMC

SD (Secure Digital) / Mini SD / SDHC / SDXC

MS (Memory Stick) / MS Pro / MS Duo

Push the card into the slot and it will appear as a removable device.

Use this jack to connect a CATV cable if you have included the optional Mini-PCI TV Tuner in your purchase.

Consumer Infrared

Transceiver

DC-In Jack

The consumer infrared transceiver at the front of the computer allows the computer to communicate with the remote control unit supplied with the optional Mini-PCI TV Tuner.

Plug the supplied AC/DC adapter into this jack to power your computer.

DVI-Out Port The DVI-Out (Digital Visual Interface) Port is a video connector interface. This allows you to connect an external monitor, TV or Flat Panel Display etc. as a display device

(see

“Configuring an External Display using the NVIDIA Control Panel” on page B - 7

) by means of a DVI cable.

If you are using an older type of monitor you will need to use a converter to convert the signal from DVI to VGA.

Interface (Ports & Jacks)

Item

e-SATA Port e-SATA

HDMI-Out Port

HDMI-OUT

Headphone-Out Jack

Description

This e-SATA (external Serial Advanced Technology Attachment) port allows you to plug-in external Serial ATA hard drives.

The HDMI-Out (High-Definition Multimedia Interface) port is an audio/video connector interface for transmitting uncompressed digital streams. This allows you to connect an external monitor, TV or Flat Panel Display etc. as a display device (see

“Configuring an External

Display using the NVIDIA Control Panel” on page B - 7

) by means of a HDMI cable. Note that

HDMI carries both audio and video signals (see

“HDMI Audio Configuration” on page 2 -

8

).

Headphones or speakers may be connected through this jack. Note: Set your system’s volume to a reduced level before connecting to this jack.

Line-In Jack

Microphone-In Jack

The Line-In jack allows you to play audio sources through the computer’s speakers. Note that audio input through Line-in will default to the mute setting. To set up your audio sources to play ticked.

Plug an external microphone in to this jack to record on your computer.

A

Downloaded from LpManual.com Manuals

Interface (Ports & Jacks) A - 3

A

Interface (Ports & Jacks)

Item

Mini-IEEE 1394b Port

Description

This allows high-speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below).

IEEE 1394b

The Mini-IEEE 1394 ports only support SELF POWERED IEEE 1394 devices.

RJ-45 LAN Jack This port supports LAN (Network) functions.

Note: Broadband (e.g. ADSL) modems usually connect to the LAN port.

S/PDIF-Out Jack

Security Lock Slot

This S/PDIF (Sony/Philips Digital Interface Format) Out Port allows you to connect your DVDcapable PC to a Dolby AC-3 compatible receiver for “5.1” or ‘dts’ surround sound.

To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store.

Item

USB 2.0/1.1 Ports

USB 3.0 Port

3.

0

Interface (Ports & Jacks)

Description

These USB (Universal Serial Bus) 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc. Devices can be plugged into the computer, and unplugged from the computer, without the need to turn the system off (if the power rating of your USB device is 500mA or above, make sure you use the power supply which comes with the device).

The USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black. USB 3.0 will transfer data much faster than USB 2.0, and is backwards-compatible with USB 2.0.

Note that the USB 3.0 port requires a driver installation (see

“USB 3.0” on page 4 - 8

), does not support wake on USB and is not operational under DOS.

A

Downloaded from LpManual.com Manuals

Interface (Ports & Jacks) A - 5

A

Interface (Ports & Jacks)

NVIDIA Video Driver Controls

Appendix B: NVIDIA Video Driver Controls

The basic settings for configuring the LCD are outlined in

“Video Features” on page 1 - 17

.

NVIDIA Video Driver Installation

Make sure you install the drivers in the order indicated in

Table 4 - 1, on page 4 - 3

.

1.

Insert the Device Drivers & Utilities + User’s Manual disc and click Install

Drivers (button).

2. Click 2.Install Video Driver > Yes.

3. Click AGREE AND CONTINUE (button) to accept the terms of the license agreement.

4. Click NEXT.

5. Click the RESTART NOW button to restart the computer.

Video Card Options

Note that card types, specifications and drivers are subject to continual updates and changes. Check with your service center for the latest details on video cards supported. Note that not all video card options for this computer model series support SLI configuration (see

“Video Adapter Options” on page D - 2

, or contact your service center for details).

B

Downloaded from LpManual.com Manuals

NVIDIA Video Driver Installation B - 1

NVIDIA Video Driver Controls

NVIDIA Control

Panel

To access the Ge-

Force..... control panel from the desktop; rightclick the desktop, then click NVIDIA Control

Panel.

NVIDIA Control Panel (Win 7)

More advanced video configuration options are provided in the NVIDIA Control

Panel tab.

1.

Open the Display (see page

1 - 18

) control panel.

2.

Click Advanced Settings (button).

3.

Click GeForce..... (tab).

4.

Click Start the NVIDIA Control Panel to make any video adjustments.

OR

1.

Click Start, and click Control Panel (or point to Settings and click Control Panel).

2.

Double-click NVIDIA Control Panel (click "Classic View" from the left of the menu if you are in Control Panel Home).

B

Figure B - 1

NVIDIA GeForce.....

Control Panel

NVIDIA Video Driver Controls

The NVIDIA Control Panel provides additional video configuration controls and tools which allow quick access to features such as display configuration, 3D Settings and Help menus etc.

Navigating the

Control Panel

Navigate through the control panels in much the same way as you would a web page.

Click on the sub-heading tasks in the left menu (and on the highlighted links) for information. Use the buttons on the top left to go back, forward etc.

Figure B - 2

NVIDIA Control

Panels

B

Downloaded from LpManual.com Manuals

NVIDIA Control Panel (Win 7) B - 3

B

NVIDIA Video Driver Controls

The Help menus provide index and search features, and direct links to the NVIDIA website etc.

Figure B - 3

Help Menu

NVIDIA Video Driver Controls

Display Devices

Note that you can use a DVI cable connected to the DVI-Out port, or an HDMI

(High-Definition Multimedia Interface) cable connected to the HDMI-Out port to connect an external display (if you are using an older type of monitor you can use a converter to convert the signal from DVI to VGA). See your display device manual to see which formats are supported.

1.

The built-in LCD.

2.

An external display connected to the DVI-Out Port.

3.

An external display/TV (if the TV supports an HDMI connection) connected to the

HDMI-Out Port.

Monitor and TV Tuner

If you are connecting both a monitor/flat panel display to the DVI-Out Port, and a cable/aerial to the optional TV Tuner module, make sure you attach the cable/aerial to the TV Tun-

er first, then the monitor.

Display Devices

Besides the built-in

LCD, you can also use an external monitor/flat panel display as your display device. The display options are:

• The built-in LCD.

• An external display connected to the DVI-

Out port.

• An external display connected to the

HDMI-Out port.

Note that HDMI supports video and audio signals.

DO NOT use the Fn +

F7 key combination to toggle through display options when SLI is enabled.

B

Downloaded from LpManual.com Manuals

Display Devices B - 5

B

NVIDIA Video Driver Controls

SLI Configuration &

Multiple Displays

Note that if SLI configuration is enabled only a

Single display may be used as the display device.

DO NOT use the Fn +

F7 key combination to toggle through display options when SLI is enabled. SLI supports only a Single display, and attempting to configure dual displays may cause an error. Use the NVID-

IA control panel to select the display to be used.

Display Modes

Single Display Mode

Only one of your displays is used.

Duplicate Displays

Duplicate simply shows an exact copy of the Primary display desktop on the other display(s). This mode will drive multiple displays with the same content.

Extend Desktop

Extend Desktop treats both connected displays as separate devices, and they act as a virtual desktop resulting in a large workspace. When enabled, you can drag any icons or windows across to the other display desktop. It is therefore possible to have one program visible in one of the displays, and a different program visible in the other display.

NVIDIA Video Driver Controls

Configuring an External Display using the NVIDIA Control Panel

You can use the NVIDIA control panel to configure any attached displays.

1.

Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on.

2.

Go to NVIDIA Control Panel (see page

B - 2

).

3.

Double-click Display (if the sub-menus are not visible), and then click Set up

multiple displays.

4.

Any attached display will appear under “1.Select the displays you want to use.

Display Not Shown

If the attached display does not appear in the

1.Select the displays

you want to use.window, click My Display

is not shown... and then click the appropriate button to force detection of the missing display.

Figure B - 4

Set Up Multiple

Displays

B

5.

Click the tickbox alongside any display you wish to use.

6.

Click Apply > Yes to save any changes made.

Downloaded from LpManual.com Manuals

Display Modes B - 7

NVIDIA Video Driver Controls

Duplicating the Displays

1.

Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on.

2.

Go to NVIDIA Control Panel (see page

B - 2

).

3.

Double-click Display (if the sub-menus are not visible), and then click Set up

multiple displays.

4.

Any attached display will appear under 1.Select the displays you want to use.

5.

Click the tickbox alongside any display you wish to use.

6.

Right-click one of the display icons and click “Duplicate displays....” (select which is to be the primary display) to duplicate the desktop on both displays.

B

Figure B - 5

Duplicate

Displays

Right-click to select Duplicate displays

and which is to be used as the primary clone

Select Apply > Yes to save changes

7.

Click Apply > Yes to save any changes.

NVIDIA Video Driver Controls

Extending the Display

1.

Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on.

2.

Go to NVIDIA Control Panel (see page

B - 2

).

3.

Double-click Display (if the sub-menus are not visible), and then click Set up

multiple displays.

4.

Click to select a primary display under 1.Select the displays you want to use.

5.

Right-click one of the display icons and click “Extend Desktop on this display....” to extend the desktop across both displays.

Select Apply > Yes to save changes

Figure B - 6

Extend the Display

Click to select the display to be used as the primary display

B

Right-click Extend desktop on this display

6.

Click Apply > Yes to save any changes.

Downloaded from LpManual.com Manuals

Display Modes B - 9

B

NVIDIA Video Driver Controls

Changing the Primary Display on Extended Displays

1.

If you want to switch the primary display if the displays are extended then rightclick the secondary display icon.

2.

Select Make this the Windows primary display.

3.

Click Apply > Yes to save the change.

Figure B - 7

Switch Primary

Display

Select Apply > Yes to save changes

Right-click to select the secondary display and select Make this the Windows primary display.

NVIDIA Video Driver Controls

Attaching Other Displays (Win 7)

Configuring an External Display in Windows 7

1.

Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on.

2.

Go to the Screen resolution control panel.

3.

Click the Detect button.

4.

The computer will then detect any attached displays.

Function Key

Combination

You can use the Fn + F7 key combination to toggle through the display options:

• Notebook Only

• External Display Only

• Notebook + External

Display

Make sure you give the displays enough time to refresh.

DO NOT use the Fn + F7 key combination to toggle through display options when SLI is enabled.

Downloaded from LpManual.com Manuals

Figure B - 8

Screen Resolution

Multiple Displays

(Win 7)

Attaching Other Displays (Win 7) B - 11

B

B

NVIDIA Video Driver Controls

5.

You can configure the displays from the Multiple Displays menu.

Figure B - 9

Screen Resolution

Multiple Display

Options

(Win 7)

• Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s)

• Extend these displays - Treats both connected displays as separate devices

• Show desktop only on 1/2 - Only one of your displays is used.

NVIDIA Video Driver Controls

Using the Windows Logo Key + P Key Combination to Switch Displays

You can also use the + P key combination to quickly change display configuration and modes (this is particularly useful when attaching a projector) in Windows 7.

1.

Attach your external display to the external monitor port and turn it on.

2.

Press the

+ P

key combination.

3.

An on-screen menu will pop up.

4.

Use the cursor keys (or

+ P

) to select the appropriate configuration from the menu, and press Enter to confirm the selection.

Figure B - 10

+ P Display

Configuration

Selection

(Win 7)

B

Downloaded from LpManual.com Manuals

Attaching Other Displays (Win 7) B - 13

B

NVIDIA Video Driver Controls

Video Card

Options

Note that card types, specifications and drivers are subject to continual updates and changes. Check with your service center for the latest details on video cards supported.

Note that not all video card options for this computer model series support SLI configuration (see

“Video

Adapter Options” on page D - 2

, or contact your service center

for details).

SLI Multi GPU Configuration

This computer features an NVIDIA Scalable Link Interface (SLI) that improves graphic quality and performance by combining dual NVIDIA GPUs (two video cards are required) in a single system. To enable/disable SLI Configuration:

1.

Go to NVIDIA Control Panel (see page

B - 2

).

2.

Click “+” next to 3D Settings if its sub-items are not shown and then click Set SLI

and PhysX configuration.

Select Restart Now to restart the computer

Figure B - 11

Set SLI

Configuration

3.

Click “Maximize 3D Performance” under “SLI configuration:”.

4.

Click to select “PhysX settings; Auto-select (recommended) is the default setting.

5.

Click Apply and Restart Now to restart the computer (see over).

NVIDIA Video Driver Controls

SLI Multi GPU Configuration & Battery Power

Note that due to the high power and system demands created by enabling SLI Configuration, you should not enable SLI configuration if your computer is powered

by battery only. If you attempt to run an SLI configuration when the computer is powered by the battery only, then system problems may occur.

• If the computer is currently powered by battery only do not enable SLI config-

uration.

• If you have currently enabled SLI configuration, and the computer is powered by the AC/DC adapter, do not switch to battery power only (or go to the

NVIDIA Control Panel and disable SLI configuration before switching to battery power only).

SLI Configuration &

Multiple Displays

Note that if SLI configuration is enabled only a

Single display may be used as the display device.

DO NOT use the Fn +

F7 key combination to toggle through display options when SLI is enabled. SLI supports only a Single display, and attempting to configure dual displays may cause an error. Use the NVID-

IA control panel to select the display to be used.

B

Downloaded from LpManual.com Manuals

SLI Multi GPU Configuration B - 15

B

NVIDIA Video Driver Controls

Detect Displays

To get a full range of display options click “My dis-

play is not shown in the

list...”.

HDMI Audio Setup

See

“HDMI Audio Configuration” on page 2 -

8

for instructions on configuring audio for HDMI display devices.

Set up your external display (TV or LCD) for

HDMI input (see your display device manual).

Enabling TV Display

To display desktop images on a TV, connect the TV to your computer by using an

HDMI cable/DVI cable from the TV to the HDMI-Out port/DVI-Out port (if supported by your TV).

You will need to enable the TV display from the NVIDIA Control Panel as per the instructions on

B - 7

. The TV will appear as a display option (1. Select the displays

you would like to use.) when attached to the appropriate port. Apply the settings, and then click Yes to save the changes.

Figure B - 12

Set Up Multiple

Displays

(with TV connected)

NVIDIA Video Driver Controls

Changing the TV Signal Format

1.

When the TV is enabled as a display device click the sub-menus under Video &

Television.

2.

Click “Change the signal or HD format”.

3.

Select the connector or format you want to use (the menu that appears will depend upon your type of connector).

4.

Apply the settings, and then click Yes to save the changes.

Figure B - 13

Change the Signal or

HD Format

Downloaded from LpManual.com Manuals

Enabling TV Display B - 17

B

B

NVIDIA Video Driver Controls

The NVIDIA Control Panel provides additional configuration controls to adjust the

TV settings in the Video & Television menu.

Figure B - 14

NVIDIA Control

Panels

(Video &

Television)

AMD Video Driver Controls

Appendix C: AMD Video Driver Controls

The basic settings for configuring the LCD are outlined in

“Video Features” on page 1 - 17

.

Video Driver Installation

Make sure you install the drivers in the order indicated in

Table 4 - 1, on page 4 - 3

.

Video (VGA)

1.

Click 2.Install Video Driver > Yes.

2. Click Next > Install (button).

3. Click the Express (or Custom if you prefer to manually configure the driver installation settings) button and click Next.

4. Click Accept (button) and click Yes.

5. Click Finish > Yes to restart the computer.

6. After the computer has restarted, click Restart Now to restart again to refresh the video driver.

Note: After installing the video driver go to the Display/Display Settings control panel to adjust the video settings to the highest resolution.

Video Card Options

Note that card types, specifications and drivers are subject to continual updates and changes. Check with your service center for the latest details on video cards supported (see

“Video Adapter Options” on page D - 2

/

D

- 3

, or contact your service center for de-

tails).

C

Downloaded from LpManual.com Manuals

Video Driver Installation C - 1

C

AMD Video Driver Controls

Taskbar Icon

The Catalyst

TM Control

Center can also be accessed by double-clicking the icon in the taskbar (or by right-clicking the icon and selecting Config-

ure Graphics).

If you don’t see the icon in the taskbar, click Prefer-

ences in the Catalyst

TM

Control Center, and select

Enable System Tray

Menu (see over).

Catalyst

Control Center

Adjust the video settings from the Catalyst™ Control Center.

1.

Right-click the desktop and select Catalyst Control Center.

OR

2.

Click Advanced settings in the Screen Resolution control panel (see

“Video

Features” on page 1 - 17

), click the Catalyst Control Center tab and then click

ATI Catalyst control Center.

Right-Click for Menu

Figure C - 1

Catalyst Control

Center Access

AMD Video Driver Controls

Catalyst™ Control Center Preferences

The Preferences button in the Catalyst

Control Center menu allows you to configure the control panel settings. You can view the control panel in either Standard

View or Advanced View. To display Standard View or Advanced View:

1.

Open the Catalyst™ Control Center.

2.

Click the Preferences button and select either Advanced View or Standard View.

Preferences &

Views

You can switch between

Advanced and Stan-

dard views from the

Preferences menu.

Right-Click for Menu

Figure C - 2

Catalyst Control

Center Preferences

C

Downloaded from LpManual.com Manuals

Catalyst™ Control Center C - 3

AMD Video Driver Controls

Standard View

The Standard View menus feature a series of menu headings with clickable submenus which allow you to adjust Desktops and Displays, Power, Video, Gaming and Information. Click the Start button to access the top level menu from any submenu heading.

C

Figure C - 3

Catalyst Control

Center Standard View

AMD Video Driver Controls

Advanced View

The Advanced View menus display all the menu headings as a series of buttons on the left. Click the arrows in any button to display the sub-menus (note all the figures in the remainder of this chapter are in Advanced View).

Sub-Menus

Click a menu button to expand any sub-menus, and then click the appropriate sub-menu heading to configure the item.

Figure C - 4

Catalyst Control

Center Advanced View

Catalyst Control Center Versions

Due to driver updates your Control Center screens may appear slightly different from those pictured on these pages.

Downloaded from LpManual.com Manuals

Catalyst™ Control Center C - 5

C

C

AMD Video Driver Controls

Help Menus

Press F1 to bring up

Help menu. Click the question mark icon in the top right to bring up help on a specific page.

The Catalyst

Control Center provides additional video configuration controls and tools which allow quick access to features such as display options, 3D Settings, color, power and Information menus etc. Adjust settings from the options in the submenus.

Figure C - 5

ATI Catalyst Control

Center Advanced

Menus

AMD Video Driver Controls

Display Devices & Options

Note that you can use a DVI cable connected to the DVI-Out port, or an HDMI

(High-Definition Multimedia Interface) cable connected to the HDMI-Out port to connect an external display. See your display device manual to see which formats are supported.

Display Mode

Single

Duplicate

Extend

Description

One of the connected displays is used as the display device

Both connected displays output the same view

Both connected displays are treated as separate devices, act as a virtual desktop and may be configured independently

Table C - 1

Display Modes

Downloaded from LpManual.com Manuals

Display Devices & Options C - 7

C

C

AMD Video Driver Controls

Detect Displays

Click Detect Displays

(button) to automatically update the attached display information.

You can set a preference for automatic display detection in

Advanced

Display

Settings (Desktop

Management). You can choose to have attached displays automatically detected when the CCC is opened, or to use manual detection only.

Configuring an External Display In the CCC

You can use the Catalyst

Control Center to configure any attached displays.

1.

Attach your external display to the external monitor port/HDMI-Out port, and turn it on.

2.

Open the Catalyst™ Control Center.

3.

Select Desktop Management from the menu on the left (click the arrow to expand the menu) and click Creating and Arranging Desktops.

4.

Attached displays will appear in the lower part of the screen (click Detect Displays to find any attached displays that do not automatically appear).

Figure C - 6

Desktop

Management

Click Detect Displays to find any attached displays that do not automatically appear.

AMD Video Driver Controls

5.

Click the triangle icon (or right-click the display icon) on the attached display icon at the bottom to bring up the options (e.g Duplicate or Extend).

6.

Select an option from the menu (click Continue if required), and click Yes to accept the settings.

Disable Displays

If you want to disable any of the displays, right-click the display icon at the bottom of the screen and click

Disable.

Attached displays will appear here.

7.

An extra menu button (e.g. My VGA Displays) will be available to offer configuration options for your external display (depending on the type of display attached).

Figure C - 7

Desktop

Management with

External Display

C

Downloaded from LpManual.com Manuals

Display Devices & Options C - 9

C

AMD Video Driver Controls

My Digital Flat-Panels

An additional menu button entitled My Digital Flat-Panels will appear (depending on the type of display attached) when an external display is attached. This menu allows you to configure the properties of the external display. After making any adjustments you may need to click the Apply button to confirm the changes.

Figure C - 8

My Digital Flat-

Panels

AMD Video Driver Controls

HDTV Support

If your flat panel supports HDTV functions then this can be configured from My

Digital Flat-Panels > HDTV Support (Digital Flat-Panel).

Figure C - 9

My Digital Flat-

Panels

(HDTV Support)

Downloaded from LpManual.com Manuals

Display Devices & Options C - 11

C

C

AMD Video Driver Controls

Function Key

Combination

You can use the Fn + F7 key combination to toggle through the display options:

• Notebook Only

• External Display Only

• Notebook + External

Display

Make sure you give the displays enough time to refresh.

Configuring an External Display In Windows 7

1.

Attach your external display to the external monitor port/HDMI-Out port, and turn it on.

2.

Go to the Screen resolution control panel (see

“Video Features” on page 1 - 17

).

3.

Click the Detect button.

4.

The computer will then detect any attached displays.

Figure C - 10

Screen Resolution

Multiple Displays

(Win 7)

5.

You can configure the displays from the Multiple Displays menu.

AMD Video Driver Controls

Figure C - 11

Screen Resolution

Multiple Display

Options

(Win 7)

• Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s)

• Extend these displays - Treats both connected displays as separate devices

• Show desktop only on 1/2 - Only one of your displays is used.

Downloaded from LpManual.com Manuals

Display Devices & Options C - 13

C

C

AMD Video Driver Controls

Using the Windows Logo Key + P/Fn +F7 Key Combination to Switch

Displays

You can also use the + P/Fn + F7 key combination to quickly change display configuration and modes (this is particularly useful when attaching a projector) in

Windows 7.

1.

Attach your external display to the external monitor port and turn it on.

2.

Press the

+ P/Fn + F7

key combination.

3.

An on-screen menu will pop up.

4.

Use the cursor keys (or

+ P/Fn + F7

) to select the appropriate configuration from the menu, and press Enter to confirm the selection.

Figure C - 12

+ P/Fn + F7

Display

Configuration

Selection

(Win 7)

AMD Video Driver Controls

PowerPlay™

When enabled, PowerPlay

can be used to automatically set to adjust the graphics processor settings for higher performance or longer battery life when the system is either Plugged In or on Battery.

Figure C - 13

PowerPlay

Downloaded from LpManual.com Manuals

Display Devices & Options C - 15

C

C

AMD Video Driver Controls

Gaming

The Gaming menu includes configuration options for AMD CrossFireX

.

AMD

CrossFireX

combines the processing power of multiple GPUs to s single display, and this may be enabled/disabled from the AMD CrossFireX

Configuration

menu (this sub-menu is also available in the Performace menu).

Figure C - 14

Gaming AMD

CrossFireX

Configuration

AMD Video Driver Controls

HDMI Audio Configuration

HDMI (High-Definition Multimedia Interface) carries both audio and video signals.

Configure the audio output as per the instructions below.

1.

Connect a device with HDMI support to the HDMI-Out port.

2.

Click Start, and click Control Panel (or point to Settings and click Control Panel).

3.

Click Sound (Hardware and Sound), and click Playback (tab).

4.

Depending on your display, the playback device may be selected automatically; however in some cases you may need to select the audio device and click Set Default

(button) or select Realtek Digital Output and click Set Default (button).

Figure C - 15

Sound - HDMI

Device

(Set Default)

C

Downloaded from LpManual.com Manuals

HDMI Audio Configuration C - 17

C

AMD Video Driver Controls

5.

Double-click the connected HDMI device (or right-click and select Properties) to adjust the HDMI settings from the control panel tabs.

6.

Click OK to close the control panel (see notes overleaf).

Figure C - 16

HDMI Device

Properties

AMD Video Driver Controls

HDMI Notes

• Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device.

• To play audio sources through your external display’s (TV or LCD) speakers you will need to go to the audio configuration control panel on the display and configure the audio input accordingly (see your display device manual).

HDMI Video Configuration

1.

Connect an HDMI cable from the HDMI-Out port to your external display.

2.

Configure your external display as per the instructions in

“Configuring an

External Display In the CCC” on page C - 8

.

3.

Set up your external display (TV or LCD) for HDMI input (see your display device manual).

4.

You can now play video/audio sources through your external display.

Other Applications

If you are using a third party application to play DVDs etc. from any attached DVD device, you will need to consult the application’s documentation to see the appropriate audio configuration

(the application must support digital to analog translation).

Downloaded from LpManual.com Manuals

HDMI Audio Configuration C - 19

C

C

AMD Video Driver Controls

Specifications

Appendix D: Specifications

Latest Specification Information

The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your service center for details.

Downloaded from LpManual.com Manuals

Specifications D - 1

D

D

Specifications

Processor

Intel® Core i7 Processor:

=============================== i7-990x (3.46GHz)

6.4 GT/s on QPI, 12M L3 Cache, 32nm (32

Nanometer), LGA1366 Package, TDP130W

i7-980x (3.33GHz)

6.4 GT/s on QPI, 12M L3 Cache, 32nm (32

Nanometer), LGA1366 Package, TDP130W

i7-975 (3.33GHz)

6.4 GT/s on QPI, 8M L3 Cache, 45nm (45

Nanometer), LGA1366 Package, TDP130W

i7-950 (3.06GHz)

4.8 GT/s on QPI, 8M L3 Cache, 45nm (45

Nanometer), LGA1366 Package, TDP130W

i7-930 (2.8GHz)

4.8 GT/s on QPI, 8M L3 Cache, 45nm (45

Nanometer), LGA1366 Package, TDP130W

i7-920 (2.66GHz)

4.8 GT/s on QPI, 8M L3 Cache, 45nm (45

Nanometer), LGA1366 Package, TDP130W

Core Logic

Intel® X58 + ICH10R

Display

17.3" (43.94cm) FHD (1920 * 1080), 16:9

Wide Screen LED Backlit LCD

Memory

Triple Channel DDRIII (DDR3)

Three 204 Pin SO-DIMM Sockets

Supporting DDRIII (DDR3) 1066MHz/

1333MHz Memory Modules

Memory Expandable up to 12GB

Compatible with 1GB, 2GB or 4GB Modules

Video Adapter Options

nVIDIA® GeForce GTX 485M PCIe

Video Card

2GB GDDR5 Video RAM On Board

Supports PCIe * 16

Supports Microsoft DirectX ® 11.0

Supports HDCP

Supports DVI Dual Link

Supports HDMI 1.4

NVIDIA PhysX™

GeForce CUDA™ Technology

Video Adapter Options

nVIDIA® GeForce GTX 470M PCIe

Video Card

1.5GB GDDR5 Video RAM on board

Supports PCIe * 16

Supports Microsoft DirectX

®

11.0

Supports HDCP

Supports HDMI 1.4

Supports SLI

Supports DVI Dual Link nVIDIA® GeForce GTX 460M PCIe

Video Card

1.5GB GDDR5 Video RAM on board

Supports PCIe * 16

Supports Microsoft DirectX ® 11.0

Supports HDCP

Supports HDMI 1.4

Supports SLI

Supports DVI Dual Link

See over for more video adapter information

Video Adapter Options

nVIDIA® Quadro FX 3800M PCIe Video

Card (Does not support SLI)

1GB GDDR3 Video RAM On Board

Supports PCIe * 16

Supports Microsoft DirectX® 10.1

Supports HDCP

Supports DVI Dual-Link

Supports Open GL 3.1

nVIDIA® Quadro 5010M PCIe Video

Card (Does not support SLI)

4GB GDDR5 Video RAM On Board

Supports PCIe * 16

Supports Microsoft DirectX

®

11.0

Supports HDCP

Supports DVI Dual-Link

Supports Open GL 4.1

Video Adapter Options

nVIDIA® GeForce GTX 560M PCIe

Video Card

1.5GB GDDR5 Video RAM On Board

Supports PCIe * 16

Supports Microsoft DirectX ® 11.0

Supports HDCP

Supports DVI Dual Link

Supports HDMI 1.4a

NVIDIA PhysX™

GeForce CUDA™ Technology

Supports SLI nVIDIA® GeForce GTX 580M PCIe

Video Card

2.0GB GDDR5 Video RAM On Board

Supports PCIe * 16

Supports Microsoft DirectX ® 11.0

Supports HDCP

Supports DVI Dual Link

Supports HDMI 1.4

NVIDIA PhysX™

GeForce CUDA™ Technology

Specifications

Video Adapter Options

AMD Radeon™ HD 6970M

PCIe * 16 Video Card (Crossfire x PCIe *

16)

2GB GDDR5 Video RAM On Board

Supports Microsoft DirectX ® 11.0

Supports HDCP

Supports Crossfire

AMD Radeon™ HD 6990M

PCIe * 16 Video Card (Crossfire x PCIe *

16)

2GB GDDR5 Video RAM on board

Microsoft DirectX® 11 compatible

Supports HDCP

BIOS

One 16Mb Flash ROM

Phoenix™ BIOS

See over

D

Downloaded from LpManual.com Manuals

Specifications D - 3

D

Specifications

Storage

Up to three (Factory Option)

Changeable 2.5" 9.5 mm (h) SATA

(Serial) Hard Disk Drives supporting

RAID level 0/1/5

One 12.7 mm Super Multi/Blu-Ray

Combo/Blu-Ray Writer SATA Optical

Device Drive (Factory Option)

Audio

High Definition Audio

S/PDIF Digital Output

UAA (Universal Audio Architecture)

Built-In Microphone

5 Built-In Speakers and One Sub woofer

Dolby Home Theater Certified

Keyboard & Pointing Device

Full Size Winkey Keyboard with Numeric

Keypad

Built-In TouchPad (with Multi Gesture

Functionality)

Touch Sensor Instant Keys

(Mute, Vol Control, Bluetooth, WLAN &

Camera)

Slots

One ExpressCard/34 Slot

Three Mini Card Slots:

Slot 1 for PCIe WLAN Module

Slot 2 for PCIe TV Tuner Module

Card Reader

Embedded Multi-In-1 Card Reader

- MMC / RSMMC

- SD / Mini SD / SDHC / SDXC

- MS / MS Pro / MS Duo

Note: Some of these cards require PC adapters that are usually supplied with the cards.

Interface

Two USB 3.0 Ports (No DOS Support)

Three USB 2.0 Ports

One HDMI-Out (High-Definition

Multimedia Interface) Port-1.4 (with

HDCP Support)

One DVI-Out Port (with CRT out)

One eSATA Port

One S/PDIF Out & Surround Out Combo

Jack (supporting external 7.1ch audio)

One Headphone/Speaker-Out Jack

One Microphone-In Jack

One Line-In Jack

One Mini-IEEE1394b Port with TI

Controller

One RJ-45 LAN Jack

One DC-In Jack

One CATV-In Jack (for TV Tuner)

One Consumer Infrared Transceiver for

TV Tuner Remote Controller

Specifications

Communication

Built-In 10/100/100 Base-TX Ethernet LAN

Bluetooth v2.1 + EDR (Enhanced Data

Rate) Module (Factory Option)

Combo Bluetooth v3.0+HS & 802.11b/g/n

Wireless LAN Half Mini-Card Module

(Factory Option)

Intel® Centrino® Advanced-N 6230 2*2

(802.11 a/g/n) Half Mini-Card PCIe WLAN +

Bluetooth V3.0+HS Combo Module (Facto-

ry Option)

Intel® Centrino® Advanced-N 6200 2 * 2

(802.11 a/g/n) Half Mini-Card PCIe WLAN

Module (Factory Option)

Intel® Centrino® Ultimate-N 6300 3 * 3

(802.11 a/g/n) Half Mini-Card PCIe WLAN

Module (Factory Option)

3rd Party 802.11b/g/n Wireless LAN PCIe

Interface Half Mini-Card Module (Factory

Option)

2.0M Pixel PC Video Camera Module with USB Interface

Hybrid TV Tuner Module (Factory

Option)

Security

Security (Kensington® Type) Lock Slot

BIOS Password

Fingerprint Reader Module

Trusted Platform Module V1.2

Operating System

Windows® 7

Note that the TV Tuner module (factory) option in is supported by the Windows

Media Center software. Windows Media

Center is not included in Starter or

Home Basic versions of Windows 7.

Power Management

Supports Wake on LAN

Supports Wake on USB (for USB 2.0

Ports Only)

Power

Full Range AC/DC Adapter – AC in 100 -

240V, 50 - 60Hz DC Output 20V, 15A

(300 Watts)

Removable Polymer Smart Lithium-Ion

78.44Wh Main Battery

Environmental Spec

Temperature

Operating: 5

°

C - 35

°

C

Relative Humidity

Physical Dimensions & Weight

419mm (w) * 286mm (d) * 56.5 - 60.7mm

(h)

5.5kg with Single nVIDIA® GeForce GTX

485M Video Card, ODD and 78.44Wh

Battery

D

Downloaded from LpManual.com Manuals

Specifications D - 5

D

Specifications

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement