Baja motorsports SC150 Scooter Owner's Manual

SC150 SCOOTER

Read this manual carefully. It contains important safety information.

No one under the age of 16 should operate this scooter.

OWNER’S MANUAL

Minimum Recommended Age

Requirement 16

Rev. B

030909

Always wear a helmet; It could save your Life!

Do not remove this operator’s manual from this vehicle.

Please obtain, review, and follow provincial / municipal government acts and regulations pertaining to owning and operating this scooter.

Congratulations on your purchase of the BAJA INC. SC150 Scooter.

Your Scooter is warranted to be free of manufacturing defects in material and workmanship for a period of 90 days from the date of purchase. During the warranty period BAJA INC. will at its option, repair, provide replacement parts or replace your BAJA INC. 150cc

Scooter at no charge. This warranty does not cover normal wear items or damage caused by neglect or misuse of the product.

Engine Warranty – 90 days

Frame Warranty – 90 days

Warranty is void if:

Frame is bent or broken due to abuse

Wheels are bent or broken

Fender bent or broken due to abuse

Any sign of impact, accident, jumping, spin-outs or roll over.

BAJA INC. is not liable for any damage claim or liability claim person or otherwise resulting from the operation of this product in any way.

Should you experience with your vehicle, please contact Baja Inc. customer service line toll free at 1-888-863-2252 between the hours of 7am and 5pm

Monday through Friday MST (Mountain Standard Time). MDT (Mountain

Daylight Time) during daylight savings time. You will be instructed how to proceed.

A COPY OF THE SALES RECEIPT IS REQUIRED.

II

!

WARNING

This manual should be considered as a permanent part of the vehicle and should remain with the vehicle when resold or otherwise transferred to a new user or operator.

The manual contains important safety information and instructions which should be read carefully before operating the vehicle. All operators should obtain, review, and follow provincial and municipal government acts and regulations pertaining to owning and operating an on-road vehicle. Children under the age of 16 should never operate this vehicle.

!

WARNING

It is the operators responsibility to know and obey all applicable local, state and federal laws at all times while operating this vehicle including but not limited to traffic safety, vehicle registration, emissions, and noise

!

WARNING

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

CALIFORNIA PROPOSITION 65

III

Table of Contents

IMPORTANT ........................................................................................................ 2

GENERAL PRECAUTIONS/WARNINGS ............................................................ 3

NHTSA SAFETY NOTICE .................................................................................... 8

PRE RIDE CHECK LIST ...................................................................................... 9

LOCATION OF WARNING LABELS................................................................... 12

OPERATION ........................................................................................................ 13

STARTING THE ENGINE ............................................................................. 13

DRIVING SAFELY ........................................................................................ 14

SHUTTING OFF THE ENGINE .................................................................... 15

STOPPING THE VEHICLE .......................................................................... 15

PARKING ..................................................................................................... 15

BREAKING IN .............................................................................................. 15

IGNITION SWITCH ...................................................................................... 16

BRAKE LEVERS AND THROTTLE ............................................................. 16

RIGHT BRAKE/SWITCH ASSEMBLY ......................................................... 17

KICK STARTER ........................................................................................... 18

LEFT BRAKE/SWITCH ASSEMBLY ........................................................... 18

INSTRUMENT PANEL ................................................................................. 19

SEAT LOCK ................................................................................................. 20

FUEL TANK .................................................................................................. 20

BATTERY INSTALLATION .................................................................................. 21

MAINTENANCE ................................................................................................... 24

SPARK PLUG .............................................................................................. 24

TRANSMISSION OIL ................................................................................... 24

ENGINE OIL ................................................................................................. 25

CHANGING ENGINE OIL, CLEANING OIL SCREEN ................................. 26

BRAKES ...................................................................................................... 27

AIR FILTER .................................................................................................. 28

IDLE SPEED ADJUSTMENT/FUEL HOSE INSP. ....................................... 29

TIRES ........................................................................................................... 30

TRANSPORTING ................................................................................................. 31

STORAGE PROCEDURE .................................................................................... 32

MAINTENANCE CHART ..................................................................................... 33

TROUBLESHOOTING ......................................................................................... 34

SPECIFICATIONS ................................................................................................ 36

ELECTRIC DIAGRAM ......................................................................................... 37

SERIAL NUMBER LOCATION ............................................................................ 38

EMISSION CONTROL SYSTEM WARRANTY .................................................... 39

1

Please read this manual and follow all instructions carefully. To emphasize the special information, the symbol and the words WARNING or CAUTION have some special meanings. Pay attention to the messages.

WARNING

Indicates a potential hazard that could result in death or injury.

!

CAUTION

Indicates a potential hazard that could result in vehicle damage.

NOTE: Indicating special information which is to make maintenance easier or instructions clearer.

WARNING and CAUTION are arranged like this:

WARNING-or-CAUTION

The first part will identify a POTENTIAL HAZARD.

The second part will describe WHAT COULD HAPPEN if you ignore the WARNING or CAUTION.

The third part will describe HOW TO AVOID THE HAZARD.

This user’s manual contains important safety and maintenance information.

Read it carefully before riding. Failing to follow the warnings contained in this manual could result in INJURY or DEATH.

It is important that this manual remain with the vehicle when you transfer it to another user or owner.

All information, illustrations, photographs and specifications contained in this manual are based on the latest product information available at the time of publication. Due to improvements or other changes, there will be some discrepancies in this manual. We reserve the right to make product changes at any time, without notice and without incurring any obligation to make the same or similar changes to the vehicle previously built or sold.

2

General Precautions

●

●

●

●

●

●

●

!

WARNING! FAILURE TO FOLLOW THESE INSTRUCTIONS CAN

RESULT IN SEVERE INJURY OR DEATH.

CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS CAN

ALSO RESULT IN DAMAGE TO THE VEHICLE AND/OR OTHER

PROPERTY.

Read and follow all instructions in this Owner’s/Operator’s Manual, any accompanying supplements. Do not discard this owner’s manual, safety video, or any other material or documentation included with this vehicle.

.

Gasoline engine exhaust from this vehicle contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. The engine exhaust contains carbon monoxide, which is tasteless, odorless, poisonous gas. Never operate this vehicle indoors or in an enclosed area with poor ventilation.

This vehicle may have been supplied to you completely assembled.

To prevent possible injury or death, read and follow the assembly instructions to make sure the vehicle was assembled properly.

Always perform the daily pre-ride inspection specified in this manual before operating this vehicle.

Modifying the vehicle and/or removing original equipment and/or safety decals could make this vehicle unsafe for operation.

Replace any safety decals that become unreadable or detached from the vehicle. Decals provide critical warnings about potential hazards or safety requirements.

Never use this vehicle for stunt riding, spin-outs, donuts, racing , or any form of competition.

3

Additional Warnings

Protective Clothing/Equipment

● Most accident fatalities are due to preventable head injuries. Always wear a properly fitting motorcycle type helmet approved by agencies such as the Department of Transportation (DOT), Safety Helmet

Council of America (SHCA), or Snell Memorial Foundation (SNELL).

●

●

Always wear face shields or goggles, boots, gloves and other appropriate protective clothing.

Long hair, loose clothes, or jewelry can get caught in moving parts below and behind the seat or your surrounding environment.

Remove or tie back anything loose that can reach below and behind the seat before riding.

Moving Parts

● Never place hands, feet, any body parts or clothing near the engine, wheels, chain and other rotating parts of the vehicle while riding or running the engine.

●

●

●

Use extreme caution when performing required maintenance while the engine is running.

Keep guards and pads in place at all times. Prevent accidental contact by any person whenever the vehicle is running.

The guards over the brake, clutch, torque-converter, axle and drive sprockets also help prevent mud and debris from contacting those components.

●

Traffic Safety

● ALWAYS FOLLOW THE ENTIRE PRE-RIDE CHECKLIST PRIOR TO

STARTING OR RIDING THE SCOOTER.

Your safety while riding this vehicle depends entirely on your ability to exercise proper judgement. You must be of sufficient age, understanding, mental capacity, and physical capability to safely operate this vehicle.

4

●

●

●

●

●

●

●

●

Additional Warnings (continued)

Traffic Safety (continued)

● Always obtain mature, supervised instruction and sufficient practice in an decongested area before operating this vehicle on any public thoroughfare.

Excessive vehicle speed is a leading cause of accidents, which can cause death or serious harm to you, other people, and/or property.

Always obey all applicable traffic safety laws while operating this vehicle, being sure to account for current weather and traffic conditions and slow down if necessary. DRIVE TO ARRIVE!

Use extreme caution when riding on wet, slippery, rough or slopped terrain. There is an increased risk of loss of control, which can result in injury, death, and/or property damage.

Always slow down when turning. High-speed turning can cause loss of control and/or possible death, injury, and/or property damage.

Practice turning in a safe area away from traffic until you are confident in your ability to control the vehicle at all times.

Operating this vehicle at an unsafe speed, especially while turning, can cause death, injury, and/or property damage.

Never use this vehicle to perform any type of racing, stunt riding, jumps, spin-outs, donuts, or other maneuvers, You could kill or injure yourself or others and/or cause property damage.

Never operate vehicle while under the influence of alcohol, drugs or medication of any kind. Such operation is dangerous to yourself and/or others.

Check the tire pressure before operating the vehicle using a properly calibrated tire air pressure gauge.

Stop the vehicle and shut off the engine immediately if the vehicle makes unusual noises or vibrations. Check the vehicle for damage.

Excessive noise or vibration is a sign of loose or worn parts.

5


Engine/Motor Safety

● Keep the engine/motor free of dirt and debris, especially in the throttle linkage area.

●

●

●

●

●

Never start the engine/motor without checking to see that the throttle control is in the idle position.

Never start the engine/motor unless you are properly seated with your hands firmly on the controls.

Never tamper with, alter, or change the vehicle’s engine/motor settings. The engine/motor governor is factory set and protects the engine/motor from damage. Excessive engine/motor speed is potentially dangerous to the operator, bystanders, and the engine/motor itself.

All guards must be in place prior to starting the engine.

Operating the vehicle in conditions where water, mud, snow, dirt, sand or other debris can get into the throttle cable conduit and/or the throttle mechanism can cause the cable or throttle mechanism to bind, which may lead to throttle sticking, loss of control, and possible death, injury, and/or property damage.

Fasteners

● Make sure that all screws, nuts, and bolts are properly tightened.

Never over-tighten hardware that is designed to move, such as front and rear wheels. Restricting moving parts can cause a loss of control and possible injury or death.

● Always replace torque-type locknuts with new locknuts of the same type after removing the old locknuts.

Fueling

● Check the fuel supply before each use. Never fill the fuel tank while the engine is running or hot. Always allow at least 1in. of expansion space at the top of the fuel tank. There should not be any fuel in the filler neck. Replace the fuel cap tightly after refueling to prevent a fuel spillage, fire, or explosion hazard.

6


Fueling (continued)

● Always use an original gas cap or an approved OEM replacement.

Never fill fuel tank while the vehicle is inside a building. Gasoline vapors can cause injury or death and can pose a fire or explosion risk.

●

●

●

●

●

●

Move the vehicle at least 10 ft. before starting the engine.

Use extreme caution when starting the engine. Hot engine, muffler, or drive components can cause serious burns on contact.

Maintenance

● Do not modify the vehicle from the manufacturer’s original design and configuration.

Never wash or operate the vehicle in freezing temperatures. Water can freeze in the throttle cable conduit and/or on the throttle mechanism, possibly resulting in throttle sticking, which can cause the engine to continue to run and result in loss of control.

Assembly, maintenance, and/or repair of this vehicle should only be performed by designated dealers or authorized repair centers to ensure quality work and safe vehicle condition.

Always disconnect the spark plug wire (gasoline vehicles) or disconnect the battery before commencing any work in the engine vicinity or where there is a possibility that the vehicle could move unexpectedly. Keep the spark plug cable away from the spark plug to avoid accidental starting.

Avoid contacting the muffler, cylinder head, or any potentially hot area on or around the engine when working on, around, or restarting the engine.

7

●

●


Maintenance (continued)

● Store this vehicle in a place where gasoline fumes cannot reach an open flame, spark, or other source of ignition. Drain the fuel tank in a cool well-ventilated area prior to any long-term storage. Never store this vehicle in a close proximity to appliances such as water heaters or furnaces.

Engine, exhausts, and other components can become extremely hot during operation. Use caution when near hot components.

Never adjust, repair, or clean the vehicle while it is in motion.

NHTSA Safety Notice

If you believe that your vehicle has a defect which could cause serious injury or death, you should immediately contact the National Highway Traffic Safety

Administration (NHTSA) in addition to notifying BAJA INC.

If NHTSA receives similar complaints, it may open an investigation and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.

However, NHTSA cannot become involved in any individual problems between you, your dealer or BAJA INC.

To contact NHTSA you may call the Auto Safety Hot line toll-free within the

United States on 1-800-424-9393 or write to: NHTSA, 400 Seventh Street SW,

Washington, DC 20590.

8

Pre-Ride Checklist

!

WARNING! ALWAYS PERFORM THE ENTIRE PRE-RIDE

CHECKLIST BEFORE USING THE VEHICLE AS THIS CAN HELP

YOU SPOT PROBLEMS THAT COULD INTERFERE WITH SAFE

VEHICLE OPERATION. FAILURE TO FOLLOW THIS ENTIRE

CHECKLIST BEFORE EVERY RIDE CAN CAUSE DEATH,

SERIOUS INJURY, AND/OR PROPERTY DAMAGE TO YOURSELF

AND/OR OTHERS

FRONT BRAKE

LEVER

REAR BRAKE

LEVER

AIR FILTER

LOCATED

UNDER SEAT

IGNITION KEY

SWITCH

GAS CAP

LOCATED

UNDER SEAT

SEAT LOCK

TAIL LIGHT

HEADLIGHTS

REAR SHOCKS

BATTERY

SIDE STAND

COMPARTMENT

LOCATED UNDER

FLOORBOARD

CENTER

STAND

CARBURETOR

KICK START

LEVER

9

Pre-Ride Checklist (continued)

Before Starting the Engine/Motor

1. Engine oil level a) Check for leaks b) Tighten filler cap securely.

c) Add oil if required.

2. Fuel level a) Add fuel as necessary.

b) Do not overfill (no fuel in the filler neck).

c) Do not mix oil with gas.

d) Replace cap tightly.

e) Do not refuel a hot engine. Allow engine to cool before adding fuel.

3. Warning decals a) Make sure all warning decals are legible and securely attached.

b) Replace as necessary.

4. Tires a) Ensure that both tires have at least 1/8 in. tread depth at center.

b) Both tires must be inflated to the pressure indicated on the tire sidewalls.

c) Replace the tires id tread height is less then 1/8 in. at the center of tires.

5. Throttle a) Check for smooth operation. Make sure the throttle “snaps” back to idle position when released.

b) Check for frayed cable or damaged cable housing. Replace damaged cable.

c) Check for mud, debris and ice in the throttle cable/mechanism.

Clean out any contamination.

10

Pre-Ride Checklist (continued)

Before Starting the Engine/Motor

6. Fasteners a) Check that axle nuts are secure.

b) Check for missing fasteners. Replace as necessary.

c) Check that all other fasteners are secure. Tighten as necessary.

7. Steering

Make sure steering turns freely.

8. Frame/chassis

Check for bent/damaged frame/chassis components. Replace as necessary.

9. Battery (if equipped)

Check to make sure connections are tight and corrosion-free.

Clean/tighten as necessary.

10. Lights (if equipped)

Check for proper operation. Replace bulbs as necessary.

11

Location of Warning Label

Read and follow the warning label on your Scooter. Make sure you understand the label. Keep the label on the Scooter. Do not remove it for any reason. If the label comes off or becomes difficult to read, you should get a replacement by contacting BAJA INC.

!

WARNING

Read and understand owners manual before operating this scooter.

Always wear a helmet, eye protection and protective clothing.

12

Operation

Starting the Engine

1

2

!

WARNING! ALWAYS RETRACT THE SIDE STAND PRIOR TO

STARTING THE VEHICLE

If the engine is cold:

Balance the scooter on its center stand (1) with the side stand (2) fully retracted. Make sure the ignition key is OFF, then rotate the throttle 5-8 times to prime the engine. Squeeze the rear brake lever, turn the key to RUN, and push the START button. Your scooter includes an automatic choke.

CAUTION: DO NOT RUN THE STARTER FOR MORE THAN 5

SECONDS AT A TIME. ALWAYS ALLOW AT LEAST 10 SECONDS

BETWEEN STARTING ATTEMPTS.

If the engine is warm:

Balance the scooter on its center stand (1) with the side stand (2) fully retracted. Squeeze the rear brake lever, turn the key to RUN, and push the

START button. If the engine does not start after 5 seconds. wait 10 seconds, then turn the throttle 1/3 turn while pressing the START button. This will override the automatic choke and help start the engine.

CAUTION: DO NOT RUN THE STARTER FOR MORE THAN 5

SECONDS AT A TIME. ALWAYS ALLOW AT LEAST 10 SECONDS

BETWEEN STARTING ATTEMPTS.

13

Operation (continued)

Driving Safely

!

WARNING! FOLLOW ALL OF THE WARNINGS IN THIS

OPERATOR’S MANUAL AT ALL TIMES WHILE OPERATING

THE SCOOTER. IT IS YOUR RESPONSIBILITY TO KNOW

AND OBEY ALL APPLICABLE LOCAL, STATE, AND

FEDERAL LAWS.

!

WARNING! NEVER OVERLOAD THE VEHICLE. THE

CARRYING CAPACITY IS 330 POUNDS.

After starting the engine, hold rear (left) brake lever and gently push the scooter forward off the center stand.

Straddle the seat while keeping one foot on the ground for stability. Slowly turn the throttle to begin driving. Place your foot on the floorboard as the scooter begins moving.

Never attach any articles to the handlebar. Stow any cargo on the luggage rack or in the under-seat storage box. Do not carry cargo weighing more than

10 pounds on the luggage rack. Always hold the rear hand hold when lifting the scooter.

!

WARNING! ALWAYS WEAR A DOT-APPROVED HELMET,

EYE PROTECTION, AND SHOES WHEN RIDING YOUR

VEHICLE.

!

WARNING! NEVER DRIVE THE SCOOTER WITH THE SIDE

STAND EXTENDED.

14


Shutting off the engine

Always shut off the engine by turning the ignition switch to OFF.

Stopping the vehicle

!

WARNING! WET, OILY, OR SANDY ROADS REDUCE

BRAKING EFFECTIVENESS. HARD BRAKING ON THESE

SURFACES COULD LEAD TO LOSS OF CONTROL AND A

SERIOUS ACCIDENT. ALWAYS REDUCE SPEED AS

GRADUALLY AS POSSIBLE.

When braking, always engage the rear brake first to retain maximum control of the scooter. Most of your stopping power comes from the front wheel.

Parking

Always leave the ignition key switch in the lock position when parking the vehicle to help prevent theft. Park on smooth hard surfaces, use the center stand whenever possible.

Breaking in

●

●

●

●

●

●

Following this break-in procedure ensures that your scooter is functioning properly and maximizes engine life.

Never drive this vehicle over 40mph during the first 250 miles of operation. Excessive speed could result in engine failure.

Always use fresh 89 octane gasoline. Avoid gasoline that contains alcohol, which can damage rubber gaskets and engine seals.

Check and adjust the brakes, throttle cable, tire pressure, and fasteners weekly before riding. This is in addition to the pre-ride inspection.

Schedule regular maintenance with your authorized BAJA INC.

service center.

Never add oil to the gasoline; your scooter has a 4-stroke engine with an internal lubricating system.

15


Ignition switch

The main ignition switch contains three positions:

3

2

4

1

●

●

●

ON (2): The engine can start, the key (1) cannot be removed.

OFF (3): This position shuts off the engine and allows the key to be removed.

LOCK (4): From the OFF position, push inward and turn the key counterclockwise to the LOCK position while turning the steering column to the left and shaking it lightly to engage the steering lock.

Remove key.

Brake Levers and Throttle

5 6

●

●

●

7

!

Rear brake (5): When stopping the scooter, squeeze the rear brake smoothly and firmly. Always engage the rear brake first.

Front brake (6): Squeeze the lever gently at first to avoid locking the front wheel. Most of your stopping power comes from the front wheel, which should always be used to supplement the rear wheel.

WARNING! USE EXTREME CAUTION WHEN ENGAGING

THE FRONT BRAKE TO AVOID LOCKING THE FRONT

WHEEL. LOCKING THE FRONT WHEEL CAN CAUSE A

SERIOUS ACCIDENT.

Throttle grip (7): The rotary throttle grip is on the right handlebar.

Accelerate by rotating the throttle towards you. Gently apply the throttle to avoid engine from stalling. Decelerate by rotating the throttle away from you. The throttle includes a safety spring that snaps the throttle back to idle when released.

16


Right switch assembly

3

2

1

4

5

●

●

Light switch (1)

● The light switch must always be on while the vehicle is in operation.

Slide light switch all the all the way to the left (2) to turn headlights on.

●

For parking lights, slide headlight switch to the middle position (3).

To turn lights off, slide headlight switch all the way to the right (4).

Electric Start Button (5). With ignition key turned on and rear brake lever pulled in, press electric start button to start the engine.

17


Kick starter

Use the kick starter to start the engine if the battery is drained. Once started, leave the engine running until the battery recharges sufficiently to restart the scooter.

●

●

●

Left switch assembly

●

Kick start Lever

High/low beam light switch (1): To activate the high beam, move the switch to position (2). For low beam, use position (3).

Turn signal switch (4): Slide the switch plate left for a left signal and right for a right signal. Press the center of the switch to cancel the turn signal.

Horn (5): Press the bottom button to sound the horn.

Emergency stop switch (6): Press this button to stop engine.

2 3

1

4

5

18

6


3

5

1

6

4 2

Instrumental panel

● Speedometer (1): Indicates the current driving speed in both km/h and mph.

● High beam indication lamp (2): Illuminates when high beam is selected.

● Turn signal lamp (3): Indicates that the turn signal is activated.

● Fuel indicator (4): Indicates the fuel level.

● Odometer (5): Indicates the total distance the vehicle has traveled.

● Tachometer (6): Indicates the r/min’s.

19


Seat lock

● To open: Insert the key just below the seat on the left side of the vehicle. Press the seat down slightly while turning the key clockwise to release the latch. Lift the seat.

● To close: Press down the seat until locked, then remove the key. Never leave the key in the lock.

Fuel tank

Locate gas cap under seat and remove, fill tank with new, clean 89 octane or higher gasoline. Do not overfill tank, do not fill over 1” below filler neck to allow for expansion. Gap tank capacity: 1.6 gal

!

WARNING! GASOLINE IS FLAMMABLE AND EXPLOSIVE.

USE EXTREME CAUTION WHEN FUELING YOUR SCOOTER

ONLY FILL THE TANK IN WELL-VENTILATED AREAS. SHUT

OFF THE ENGINE AND PLACE THE SCOOTER ON ITS

CENTER STAND TO ENSURE PROPER FILLING WHILE

ELIMINATING THE RISK OF STATIC IGNITION CAUSED BY

IMPROPER GROUNDING. NEVER SMOKE NEAR

GASOLINE. NEVER OVERFILL THE GAS TANK. ALWAYS

MAKE SURE THE FUEL CAP IS SECURELY FASTENED

AFTER EACH FUELING.

!

WARNING! DO NOT SPLASH OR SPILL GASOLINE WHILE

FUELING. IF A SPILL OCCURS, IMMEDIATELY WIPE OFF

ALL SURFACES PRIOR TO STARTING THE ENGINE. AVOID

SKIN CONTACT WITH GASOLINE AND DO NOT BREATHE

GASOLINE FUMES. KEEP GASOLINE AWAY FROM FLAMES

OR ELECTRIC SPARKS.

Filler neck

Fuel Level

20

BATTERY INSTALLATION

INITIAL SERVICE AND INSTALLATION OF BATTERY:

WARNING

The following procedure is very dangerous and should be performed with utmost care and attention. Wear protective eye wear, rubber gloves, and have water available should electrolyte come in contact with skin or eyes. KEEP ALL CHILDREN AWAY FROM THE AREA WHILE

THIS PROCEDURE IS BEING PERFORMED.

POISON – CAUSES SEVERE BURNS

Contains sulfuric acid.

Avoid contact with skin, eyes, or clothing

To prevent accidents, rinse empty container with water.

ANTIDOTE:

External – flush with water

Internal – Call physician immediately. Drink large quantities of water or milk.

Follow with milk of magnesia, beaten eggs or vegetable.

Eyes – Flush with water for 15 minutes and get prompt medical attention.

KEEP OUT OF REACH OF CHILDREN.

21

BATTERY INSTALLATION (continued)

Note: The following page is for vehicles with battery’s containing separate electrolyte pack. Most battery’s will come with the electrolyte already sealed into the battery.

Preparing the battery:

· Place battery on level surface. Remove sealing tape from top. (see figure 20)

· Take the electrolyte container out of the plastic bag.

· Place electrolyte container upside down with the sealed silver mouths of the electrolyte bottles in line with the six filler holes of the battery. (see figure 21)

· Push the container down strongly enough to break the silver seals.

· As electrolyte starts flowing into battery, air bubbles will come up from the mouths of the plastic electrolyte bottles.

· Leave bottles upside down in battery holes until electrolyte is completely drained.

· Never leave children unattended around battery.

· If air bubbles cease to float to the top of the electrolyte bottles, tap lightly on top.

· DO NOT remove container from battery while it is draining.

· Never cut or pierce electrolyte container.

· After all the electrolyte has drained from the bottles into the battery, pull plastic electrolyte bottles gently out of the battery.

· Discard empty electrolyte bottles in a waste area that is inaccessible to children and animals.

· After filling let battery stand for at least 30 minutes before charging. This allows the electrolyte to penetrate plates for optimum performance and ensures longer battery life.

· After 30 minutes the battery is ready for its initial charge. Place cap strip loosely over the filling holes as shown in the picture. (see figure 22)

Figure 20

Figure 21

Figure 22

22

BATTERY INSTALLATION (continued)

How to Initially Charge the battery:

1. Connect the red positive (+) cable to the red positive (+) pole of the battery.

(see figure 23)

2. Connect the black negative (-) cable to the black negative (-) pole of the battery. (see figure 24)

Note: The red positive (+) cable has a larger diameter than the black negative (-) cable.

3. Charging rate: Charge battery @ 0.7 Amps for 5 ~ 10 hours.

• After charging is complete, press down firmly with both hands to seat the caps. (Do not pound or hammer.)

The battery is now sealed. (see figure

25)

• Locate battery compartment on scooter. The battery compartment is located under the floorboard. (see figure 26)

• Attach red positive (+) cable to positive (+) terminal on battery.

Then attach black negative (-) cable to negative (-) terminal on battery.

Figure 23

Figure 24

WARNING

NEVER REMOVE THE STRIP OF

CAPS NOR ADD ANY WATER OR

ELECTROLYTE.

Figure 25

23

Figure 26

Maintenance

Spark Plug

CHECK-UP OF SPARK PLUG

1. Remove the cap of spark plug and spark plug.

2. Clean spark plug all around or replace it if it is corroded or there is too much deposit on it.

3. Regulate the gap of the spark plug to

0.6-0.7mm (.024” - .028”)

3. The spark plug of the designated type should be used. The applicable type of spark plug: DR7HSA (NGK), A7RTC

(TORCH)

0.6~0.7mm

(.024” - .028”)

Transmission Oil

To change transmission fluid, place a catch basin under the rear of transmission case, unscrew drain plug (1) and allow oil to completely drain.

Replace drain plug and tighten securely.

Remove transmission oil filler plug (2) and fill with clean 90W oil, add 4oz.

Re-attach filler plug.

24

1 2


Engine Oil

CHECK-UPS, ADJUSTMENT AND MAINTENANCE

Checking the Oil

Check the engine oil each time prior to operating the scooter.

The oil level should be between the upper and lower lines on the dip stick

1. Set scooter on level ground, remove dipstick and clean. Re-insert dipstick, pull back out to check level.

2. Add lubricating oil up to the upper line when needed, but do not overfill.

Oil tank capacity: 0.95 qt.

3. Reinstall oil fill plug/dipstick.

Oil fill plug/dipstick

Lubricating Oil Recommended

The lubricating oil is an important factor affecting the performance and service life of the engine. Please refer to the chart for the correct grade of engine oil based on the environmental conditions in your area. Do not use any other type of oil other than what is recommended in the chart. DO NOT

MIX OIL WITH THE GASOLINE.

20W-50

Lubricating oils of different viscosity shall be employed in different regions and at different temperatures.

MACHINE

OIL

5W-40 15W-50

10W-40 10W-50

10W-30

!

CAUTION

Never start the engine when there is insufficient lubricating oil. Otherwise, it will cause harm to the engine.

TEMP.

°C

°F

-30 -20 -10

-22 -4 14

0

32

10

50

20

68

30 40

86 104

25


CHANGING ENGINE OIL, CLEANING OIL FILTER SCREEN

1. Remove Oil drain plug (1) located at the bottom left side of the engine and let oil drain into an approved collection container. DO NOT PERFORM

THIS PROCEDURE WHILE THE ENGINE IS HOT. SERIOUS BURNS

COULD RESULT FROM CONTACT WITH HOT OIL.

2. Remove the Oil filter plug (2), spring (3) and oil filter screen (4) located at the bottom right side of the engine and let the oil drain into an approved collection container. DO NOT PERFORM THIS PROCEDURE WHILE THE

ENGINE IS HOT. SERIOUS BURNS COULD RESULT FROM CONTACT

WITH HOT OIL.

2. Dispose of used oil properly. For proper disposal procedures, contact your local oil recycling center

3. Clean oil screen (4) and spring (3) with solvent

4. Clean and re-install the Oil drain Plug (1), Oil filter plug (2) with spring (3) and Oil filter (4). Screw in tightly.

5. Refill the engine with the proper amount of oil and recheck the amount of oil in the engine by using the oil fill plug/dipstick.

2

1

4

3

26


BRAKES

FRONT HYDRAULIC DISK BRAKE INSPECTION

3

2

4

1

1. Inspect front disk brake caliper (1) for leakage. If brake fluid leaks, the safety of riding could be affected.

2. Inspect the brake hose (2) for cracks, and the joint for leakage.

3. Check the brake fluid level through the sight gauge (3) in top plastic cowling, if level is at or below the LOWER mark, inspect brake pads for wear and hydraulic system for leaks.

4. To add brake fluid, unscrew the 2 screws (4) on top of the brake fluid container located under top plastic cowling. Add DOT3 or DOT4 brake fluid.

Do not mix brake fluid types.

ADJUSTMENT OF REAR BRAKE

11

1. To make rear break adjustment, turn rear adjusting nut (1) clockwise to increase and counterclockwise to reduce tension on the brake cable.

2. Brake shoes should be replaced by a qualified service technician once

“Wear arrow” reaches the “brake wear limit” .

27


AIR FILTER

1

2

Air filter (2) is located under seat of scooter.

1. The air filter cover will need to be removed (1).

2. Take air filter (2) out and check to see if it is dirty or torn, if damaged,

replace.

3. You can clean the air filter by gently tapping on a hard surface, you can

also clean by using pressurized air. Note: Too much air pressure could

damage air filter.

4. Re-install filter.

The air filter elements must be intact or the engine will suck in dust and dirt resulting in a shorter service life of the engine.

Water should be prevented from entering into the filter when washing the vehicle.

The air filter elements shall be cleaned gently to prevent from cracking or tearing. Replace filter elements with a new ones if broken or cracked.

28


IDLE SPEED ADJUSTMENT

To adjust the idle speed properly, you need a tachometer. If you do not have one, ask your authorized service center to perform this adjustment.

Engine Idle adjustment

Screw

To adjust the idle speed:

1. Start the engine and warm it up.

2. Turn the engine idle screw in or out so that the engine idle speed is at

1700+100 RPM.

WARNING

Improper adjustment of the idle speed could be hazardous.

An idle speed that is too high could cause the scooter to move forward when you start the engine. This may cause an accident.

Excessive engine wear may also result if idle speed is adjusted improperly or when the engine is not fully warmed up. Adjust the idle to the correct speed. Make sure the engine is fully warm before adjusting the engine idle speed.

FUEL HOSE

Inspect the fuel hose for damage and fuel leakage. If any defects are found, the fuel hose must be replaced.

Fuel Hose

29


Tires

1.5 mm (0.05 in)

Front Rear

Size 130/60-13 130/60-13

Tire Tread Condition

WARNING

Operating this scooter with improper tires, or even improper tire air pressure could be hazardous.

If you use improper tires or improper tire air pressure, you may loose control of the scooter.

Always use the size and type tires specified. Always maintain proper tire air pressure as described in this section.

WARNING

Using worn tires could be hazardous.

The traction of the vehicle will be decreased. This increases your risk of having an accident.

Replace the front and rear tires when the depth on the tread is 1.5 mm (0..05 in) or less.

Tire Air Pressure

Check the air pressure in tires before riding. Improper air pressure could effect handling, steering response, traction, tire life and rider comfort. Be sure that the tires are inflated to the pressures shown below. Tire pressure should only be measured or adjusted when the tires are cold.

Front

Rear

Recommended pressure

36 psi

36 psi

30

Transporting

It is best to transport the scooter in the normal upright position.

Before transporting the scooter drain the fuel from the carburetor as follows:

1. Drain fuel from carburetor into an empty container by loosening the carburetor drain screw. The carburetor drain screw is located on the bottom of the carburetor.

2. When the fuel has been drained, re-tighten the drain screw.

WARNING

Draining fuel from the carburetor could be hazardous.

Fuel could catch fire if you do not handle it properly.

When draining fuel from the carburetor, be sure to shut the engine off. Do not smoke, and never drain or refuel in an area where there are open flames or sparks. Do not spill the fuel or you may create a fire hazard. Dispose of the drained fuel properly.

Failing to secure the Scooter properly could be hazardous.

Failing to secure the vehicle properly may result in an accident or damage to the vehicle.

When transporting the Scooter, tie down the vehicle securely with straps, rope, or some other suitable means. Use extra tie downs when you transport the vehicle in the standing position.

31

Storage Procedure

If you do not use your scooter for a long period of time, it will need special service requiring appropriate materials, equipment and skill. For this reason, we recommend that you trust this maintenance work to your authorized service center. If you wish to service the machine for storage yourself, follow the general guidelines below:

VEHICLE

Place the vehicle on level ground and wash the entire vehicle.

FUEL

Drain the fuel from the fuel tank by a hand pump. Drain the fuel from the carburetor by releasing the carburetor drain screw.

WARNING

Draining the fuel could be hazardous.


When draining the fuel from the fuel tank, be sure to shut the engine off.

Do not smoke, and never drain fuel in an area where there are open flames or sparks. Keep pets and children away from the fuel, and dispose of the drained fuel properly.

TIRES

Inflate tires to the normal pressure.

EXTERNAL

1. Spray all vinyl and rubber parts with rubber protection.

2. Spray unpainted metal surfaces with rust preventative.

3. Coat painted and plastic surfaces with car wax.

PROCEDURE FOR RETURNING TO SERVICE

1. Clean the entire vehicle.

2. Make sure that the vehicle is properly lubricated.

3. Perform the INSPECTION BEFORE RIDING as listed in this manual.

4. Start the vehicle as outlined in this manual.

32

Maintenance Chart

It is very important to inspect and maintain your SC150 scooter regularly.

Follow the guidelines in the chart. The intervals between periodic services in miles are shown. At the end of each interval be sure to perform the maintenance listed.

MAINTENANCE SCHEDULE

Item Each use Initial

150

Interval (miles)

Initial

500

Initial

1000

Every

1000

Transmission Oil 80W90

Air Filter

* Carburetor

* Exhaust system

Fuel hose

Engine Oil

Engine Oil filter

Brake Fluid level

Brake Hose and joints

Brakes

Wheels

Wheel bearings

* Brake caliper linings

Front and rear suspension

Steering system

* Steering shaft lubrication

(use Li grease)

Fittings and Fasteners

* Valve Gap

I

I

I

I

I

I

I T

I

T T

* Should be completed by an authorized service center

I=Inspect and clean, adjust, lubricate or replace, if necessary.

C=Clean R=Replace T=Tighten

I

I

I

I

I

R

C

I

R R

I Every 1000 miles (more often in dusty areas)

I

I

I I

R

I

I

I

I

I

I

I

I I

I

I

C

I

I

I

I

I

I

I

I

I

I

I

T

33

Troubleshooting

This troubleshooting guide is provided to help you to find the cause of some common complaints.

COMPLAINT: Engine is hard to start or does not start at all. Something is probably wrong with the fuel system or ignition system.

!

CAUTION

Failing to troubleshoot a problem correctly can damage your scooter.

Improper repairs or adjustments may damage the vehicle. Such damage may not be covered under warranty. If you are not sure about the proper action, consult your authorized service center or BAJA INC. about the problem.

Fuel Supply Check

1. Make sure there is adequate fuel in the fuel tank.

2. Check that the ignition switch is in the “RUN “ position.

3. Make sure there is enough fuel reaching the carburetor from the fuel tank.

WARNING

Draining fuel from the carburetor could be hazardous.


When draining the carburetor, be sure to shut the engine off. Do not smoke, and never drain or refuel in an area where there are open flames or sparks. Do not spill the fuel or you may create a fire hazard.

Dispose of drained fuel properly.

a. Loosen the drain screw which is located under the carburetor.

Drain the fuel from the carburetor into a container.

b. Tighten the drain screw.

c. Run the engine for a few seconds. Shut off engine.

d. Loosen the drain screw and check that the carburetor is filled back up with fuel.

e. If fuel is reaching the carburetor, the ignition system should be checked next.

34

Carburetor drain screw

Trouble shooting (Continued)

Ignition System Check

1. Remove the spark plug and reattach it to the spark plug lead.

2. Turn ignition key to the “RUN” position. Slide the engine stop switch to the “Run” position. Push the electric button “START “(grey button).

If the ignition system is operating properly, a blue spark should jump across the spark plug gap. If there is no spark, take your machine to your service center.

WARNING

Performing the spark test improperly could be hazardous.

You could get a high voltage electrical shock if you are not familiar with this procedure.

Do not perform this check if you are not familiar with the procedure.

Do not point the spark plug near the spark plug hole during this test.

Do not do this test if you have a heart condition or wear a pacemaker.

Do not perform this test near any open fuel containers or near fuel which has spilled on the ground, on the engine, or any part of the

Scooter.

COMPLAINT: Engine stalls

1. Make sure there is enough fuel in the fuel tank.

2. Check to see that the spark plug is not fouled. Remove the spark plug and clean it. Replace it, if necessary.

3. Make sure the fuel valve is not clogged, and fuel tank is not clogged.

4. Check the idle speed. If necessary, adjust using a tachometer. The correct idle speed is 1700+100 RPM.

5. Make sure air filter is clean.

35

Specifications

DESCRIPTION

Engine type

Overall length

Overall width

Overall height

Dead weight

Payload

Suspension

Transmission

Clutch

Lubrication method

Displacement

Max speed

Fuel tank capacity

Oil tank capacity

Brake

Rear wheel

Front wheel

Spark plug

Ignition

DATA

4- Stroke / Air cooled

1942mm (76.46 inches)

702mm (27.64 inches)

1125mm (44.29 inches)

118kg (260lbs.)

150kg (330lbs.)

Telescopic fork-Front Dual shock-Rear

CVT

Auto, Centrifugal

Pressure, splash

149.6cc

55 mph

1.6 gal.

0.95 qt.

Front and Rear Hydraulic Disc

130/60-13 36 psi

130/60-13 36 psi

CR7HSA (NGK), A7RTC (TORCH)

Gap .6mm - .7mm (.024” - .028” )

CDI

36

Lb/W G Lb

B/y B

L G

Z G

37 oil Ignition C

P-pink Lb

B-black L-blue W

SERIAL NUMBER LOCATION

You need to know the frame and engine serial numbers to get warranty work, theft recovery and consumer safety information. You also need these numbers to help your authorized service center or BAJA INC. order parts.

The Frame number is stamped on front of scooter just above the front floor base. A small cap will need to be removed to see the number. The engine number is located on the bottom left side of the engine housing.

Frame number

Engine serial number

Write down the serial numbers here for your future reference

Frame No.:

Engine No.:

38

BAJA INC. – EMISSION CONTROL SYSTEM WARRANTY

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The emission control system warranty period for this vehicle begins on the date the vehicle is delivered to the first purchaser other than an authorized dealer, or the date it is first used as a demonstrator, lease, or company vehicle, whichever comes first and continues for 60 months after that date, or 12,000km, whichever comes first, provided there has been no abuse, neglect or improper maintenance of your vehicle. Where a warrantable condition exists, the Distributor will repair your vehicle at no cost to you, including diagnosis, parts and labor. If an emission-related part on your vehicle is defective, the part will be repaired or replaced by the Distributor. This is your emission control defects warranty.

OWNER’S WARRANTY RESPONSIBILITIES

As the vehicle owner, you are responsible for the performance of the required maintenance. You should maintain a record of all maintenance performed on your vehicle and retain all receipts covering maintenance on your vehicle. You may not be denied a warranty claim solely because of your failure to ensure the performance of all scheduled maintenance or lack of maintenance records or receipts. You are responsible for presenting your vehicle to an authorized dealer as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

As the vehicle owner, you should be aware that you may be denied your warranty coverage if your vehicle or a part has failed due to abuse, neglect, improper maintenance, or unapproved modifications.

WARRANTY COVERAGE

The Distributor warrants that each new 2009 and later vehicle:

• is designed, built, and equipped so as to conform at the time of initial retail purchase with all applicable regulations of the United States Environmental Protection Agency, and the

California Air Resources Board; and

• is free from defects in material and workmanship which cause such vehicle to fail to confirm with applicable regulations of the United States Environmental Protection Agency or the

California Air Resources Board for the periods specified above.

Your emission control system warranty covers components whose failure would increase an engine’s emission, including electronic controls, fuel injection system, carburetor, the ignition system, catalytic converter, or any other system utilized in this vehicle to control emission if it is originally equipped. Also included may be hoses, connectors and other emission-related assemblies. Replacing or repairing other components (including parts, labor, and other costs) not covered by this emission control system warranty or the standard warranty is the responsibility of the owner.

Coverage of repairs under this warranty applies only when repairs are completed at an authorized dealer or repair facility. The Distributor will not cover repairs performed outside of an authorized dealer or repair facility, except in an emergency situation. The use of replacement parts not equivalent to the original parts may impair the effectiveness of your vehicle’s emission control system. If such a replacement part is used and an authorized dealer determines it is defective or causes a failure of a warranted part, your claim for repair to bring your vehicle into compliance with applicable standards may be denied.

39

If an emergency situation exists when a warranted part or a dealer is not reasonably available to the owner, repairs may be performed at any available service establishment, or by the owner, using any replacement part. The Distributor shall reimburse the owner for the expenses, including diagnostic charges, not to exceed the Distributor’s suggested retail price for all warranted parts replaced and labor charges based on the Distributor’s recommend time allowance for the warranty repair and the geographically appropriate hourly labor rate. The owner may reasonably be required to keep receipts and failed parts in order to receive compensation.

This Emission Control System Warranty is in addition to the standard Limited Warranty.

EXCLUSIONS AND LIMITATIONS o o

This warranty does not cover the following:

• Failures or malfunctions of the emission control systems caused by abuse, alteration, accident, misuse, the use of leaded gasoline.

• Replacement of expendable maintenance items unless they are original equipment defective in material or workmanship under normal use, and the first required replacement interval for the item has not been reached. Expendable maintenance items include but not limited to spark plugs, filters, coolant, lubricants, gaskets, hoses, and belts.

•

•

Replacements of parts and other services and adjustments for required maintenance.

Any vehicle equipped with an odometer or hour meter where the reading is altered so that actual mileage cannot be readily determined.

• o

Repairs or replacements as a result of:

Accident

Misuse

Use of replacement parts or accessories not conforming to the original specifications which adversely affect performance

• Physical damage, corrosion, or defects caused by fire, explosions or similar causes beyond the control of the Distributor.

• Failures not caused by a defect in material or workmanship.

Use of the vehicle in any type of competitive racing or related events immediately and completely voids this and all other warranties.

LIMITED LIABILITY

The liability of the Distributor under this Emission Control System Warranty is limited solely to the remedying of defects in material workmanship by an authorized dealer at its place of business during customary business hours. This warranty does not cover inconvenience or loss of use of the vehicle or transportation of the vehicle to/from the authorized dealer. The Distributor is not liable to any person for incidental, consequential or special damages of any description, whether arising out of express or implied warranty or any other contract, negligence or other tort or otherwise.

No express emission control system warranty is given by the Distributor except as specifically set forth herein. Any emission control system warranty implied by law, including any warranty of merchantability or fitness for a particular purpose is limited to the express emission control system warranty terms stated in this warranty. The foregoing statements of warranty are exclusive and in lieu of all other remedies. All express warranties not stated in this warranty are disclaimed.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply if it is inconsistent with the controlling state law.

No dealer is authorized to modify this Emission Control System Warranty. If you have any questions regarding your warranty rights and responsibilities, you should contact BAJA INC. (888)

863-2252 or the California Air Resources Board, 9528 Telstar Avenue, El Monte, CA 91731 (for

California registered vehicles only).

40

BAJA INC.

P.O. Box 61150

Phoenix, AZ 85082

Tel: 602-443-9180

Toll Free: 888-863-2252

41