BT7832

COLLAR / PILLAR CLAMP

INSTALLATION GUIDE

SPECIFICATIONS

• Allows displays to be mounted around a column or pillar

without the need to drill into the wall

• For use with a collar compatible B-Tech flat screen mount

• Max load: 50kg (110lbs)*

*Depending on type of screen mount used

• Adjustable strap suitable for different sized columns with a

diameter from: Min.140mm (5.5") to Max. 750mm (29.5")

• Strap fimly holds onto the column without slipping

• Suitable for landscape or portrait mounting www.btechavmounts.com

50kg

(110lbs)

CONTENTS

Installation Safety Notes......................................................................................................................

2

Parts List....................................................................................................................................................

4

Installation Instructions.......................................................................................................................

5

Typical Installations...............................................................................................................................

Product Dimensions............................................................................................................................

B-Tech Contact Details........................................................................................................................

8

11

12

INSTALLATION SAFETY INSTRUCTIONS

CAUTION:

maximum weights indicated. Use with equipment heavier than the maximum indicated may result in instability causing possible injury.

Do not attempt to install this product until all instructions and warnings have been read and properly understood.

Please keep these instructions for future reference.

Please check carefully to make sure there are no missing or defective parts - defective parts must never be used.

B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire.

General

B-Tech AV Mounts recommends that a professional AV installer or other suitably qualified person install this product.

Great care must always be taken during installation as most AV equipment is of a fragile nature, possibly heavy and easily damaged if dropped.

If you do not fully understand the instructions or are not sure how to install this product safely, then please consult a professional for advice and/or to install this product for you. Failure to mount this product correctly may cause serious injury or death both during installation and at any time thereafter.

Do not mount any AV equipment that exceeds the specific weight limit of the product you are installing.

This weight limit will be clearly stated on each product and its packaging and will vary from product to product.

Product location

Please pay careful attention to where this product is located. Check load capacity of the structure prior to installation as some surfaces are not suitable for installation. Designed for indoor use, this mount is suitable for public or home installation

If located in a public or frequently populated area ensure that the product is out of the immediate reach of people.

If any AV equipment is to be suspended over the likely path or location of people then great care should be taken to secure all parts of the installation from falling.

Fixing hardware

It is highly recommended that all fixing screws be used where supplied and that the purpose of all other fixing hardware is fully understood. In some cases more AV equipment fixing hardware will be supplied to accommodate different models of equipment and set up configurations. The installer must be satisfied that any supplied fixing hardware is suitable for each specific installation. The fixing kit supplied with the product may not be suitable for all walls.

If any fixing screws or included hardware are deemed not sufficient for a safe installation then please consult a professional or your local hardware store.

Hazard limitation

When routing cables take advantage of any built in cable management features that the product might provide and ensure that all cables are tidy and secure. Check to see that any moving aspect of the product can do so unhindered by any cabling.

Some products have moving parts and the potential to cause injury through the crushing or trapping of fingers or other body parts. Particular attention to the nature of moving parts is required especially when assembling installing and adjusting during set up. Immediately after installation double-check that the work done is safe and secure. Double-check all necessary fixings are present and are of ample tightness.

It is recommended that periodic inspections of the product and its fixing points are made as frequently as possible (no more than 6 months apart) to ensure that safety is maintained.

If in doubt consult a professional AV installer or other suitably qualified person.

2

3

BT7832

PARTS LIST

PLEASE KEEP THIS FOR FUTURE REFERENCE

1 2

3 4

ITEM

1

2

3

4

PART NAME

MOUNTING PLATE

COLUMN STRAP L.2400mm

M8 x 12mm HEX SOCKET SCREW

5AF HEX KEY

Suitable for loads up to 50kg (110lbs)

QTY

2

2

4

1

INSTALLATION TOOLS

REQUIRED

Crosshead screwdriver

Cutter

Tape Measure

4

INSTALLATION INSTRUCTIONS

1.

CUT STRAP TO CORRECT LENGTH

i. Measure the circumference of the column using a tape measure.

COLUMN

X cm

TAPE MEASURE ii. To prepare the strap to the correct length add 10cm (4”) to the circumference of the column

and cut the strap accordingly.

X cm + 10cm [4"]

5

2.

ASSEMBLE STRAP TO THE COLUMN.

i. Unlock the strap and thread item 2 through item 1 .

ii. Wrap item 2 around the column and thread the end

of the strap back through item 1 and close the lock.

COLUMN

2

1 iii. Fix the strap to the column by tightening the straps with a screwdriver.

SCREWDRIVER

LOCK

6

3.

ATTACH FLAT SCREEN WALL PLATE TO THE COLUMN.

i. Fix the wall plate to item 1 using item 3 .

FLAT SCREEN

WALL PLATE

4

3

1 ii. Position the wall plate to preferred height on the column and retighten the strap if necessary.

iii. Adjust the lower strap so it aligns with the bottom fixings of the wall plate, retighten the strap

and fix to the bottom of the wall plate using item 3.

COLUMN

4

3

2

7

A. Installation with BT8441

TYPICAL INSTALLATIONS

BT7832

COLUMN

BT8441

SCREEN

B. Installation with BT8431

BT7832

COLUMN

BT8431

8

C. Installation with BT7532

BT7832 COLUMN

SCREEN

BT7532

D. Installation with BT7523

Note: Single collar mounts only require 1 strap.

BT7523

BT7832

9

E. Installation with BT7515

BT7832

BT7515

COLUMN

F. Installation with BT8312

Note: The max screen weight using the BT8312 will be reduced to 37kg (82lbs).

COLUMN

BT7832

BT8312

SCREEN

10

BT7832

DIMENSIONS

PLEASE KEEP THIS FOR FUTURE REFERENCE

TOP VIEW

FRONT VIEW

SIDE VIEW

130mm

5.12in

24mm

0.94in

750mm 29.53

2 - M8 x 1.25mm

787mm 30.99in

THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO

LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT.

11

140mm - 750mm

5.51in - 29.52in

1mm

0.04in

CONTACT: [email protected]

©2022 B-Tech International Design and Manufacturing Ltd. All rights reserved.

B-Tech AV Mounts is a division of B-Tech International Design and Manufacturing Ltd.

B-Tech AV Mounts and the B-Tech logo are registered trade marks.

All other brands and product names are trademarks of their respective owners.

Photographs are for illustrative purposes only. E&OE.

AMA-BT7832-V1-0722-57 MADE IN THE UK

For More Information Visit www.btechavmounts.com