MINI WALK 3

User Manual

Table of Contents

MINI WALK 3 by Vibra Fit User Manual

Congratulations on choosing the MINI WALK 3 by Vibra Fit.

Read this user manual carefully before starting

your MINI WALK 3 . This manual provides important tips about operating the MINI WALK 3 . In addition, it provides information that is useful for the safety of the machine.

The MINI WALK 3 is made of high-strength aluminum alloy without a welding process. The patented automatic speed control mode combines fitness, entertainment, and safety. Enjoy walking at home and in the office.

5 SAFETY INFORMATION

7 SUPPORT

8 SET UP YOUR MINI WALK 3

8 Unpacking

10 Unfold the Handrail

12 Fold the Handrail

14 Move the MINI WALK 3

15 POWER SUPPLY

15 Grounding Instructions

15 Power Requirements

15 Power the MINI WALK 3 On and Off

16 Use The MINI WALK 3

18 Handrail Buttons

19 Display Window

20 Remote Control(optional)

21 Manual Control Mode

22 Remote Control Mode(optional)

23 Automatic Control Mode

25 Sleep and Wakeup

26 BLUETOOTH SPEAKER

27 MAINTENANCE

27 Centering the walking belt

28 Add Lubricant

28 Storage

28 Cleaning

29 TROUBLESHOOTING

Safety Information

Overview

Read, understand, and carefully follow all warnings, instructions, and procedures on the treadmill and in the owners/users manual before using the treadmill.

Important safety instructions

When using an electrical appliance , basic precautions should always be followed

, including the following

:

DANGER – To reduce the risk of electric shock

:

Always unplug this appliance from the electrical outlet immediately after using and before cleaning .

WARNING – To reduce the risk of burns , fire , electric shock

, or injury to persons

:

An appliance should never be left unattended when plugged in . Unplug from outlet when not in use , and before putting on or taking off parts or before cleaning or servicing .

Do not operate under blanket or pillow . Excessive heating can occur and cause fire , electric shock , or injury to persons .

Close supervision is necessary when this appliance is used by , on , or near children , invalids , or disabled persons .

Use this appliance only for its intended use as described in this manual

.

Do not use attachments not recommended by the manufacturer .

Never operate this appliance if it has a damaged cord or plug

, if it is not working properly

, if it has been dropped or damaged

, or dropped into water

.

Return the appliance to a service center for examination and repair .

Do not carry this appliance by supply cord or use cord as a handle .

Keep the cord away from heated surfaces .

Never operate the appliance with the air openings blocked

.

Keep the air openings free of lint

, hair

, and the like .

Never drop or insert any object into any opening .

Do not use outdoors .

Do not operate where aerosol spray products are being used or where oxygen is being administered .

To disconnect , turn all controls to the off position , then remove plug from outlet .

To Avoid Injury , use extreme caution when stepping onto or off of a moving belt .

Keep children under the age of 13 away from machine

.

Connect this appliance to a properly grounded outlet only . See Grounding Instructions .

The product must be used at the specified rated voltage

/rated power supply and the power socket must be grounded.

Obtain a medical exam before beginning any exercise program.

Inspect the treadmill for incorrect, worn, or loose components and then correct, replace, or tighten prior to use.

5

Place the MINI WALK 3 on a flat surface, do not

place it on a too soft mat or too thick carpet, make

sure that the walking machine have a safe area of

2m*1m.

Keep all conductive devices away from liquids.

Do not place anything on the running platform of

MINI WALK 3 .

Don't wear clothes that can hook up to the MINI

WALK 3.

Do not allow ventilation port on the motor cover blocked by debris when using the operation.

Check regularly and lock each part, do not put

your hands on rotatable joints.

In the power-on state, do not let child or pet get close MINI WALK 3 whether you use it or not.

Do not put your fingers or any foreign objects in

the gap to avoid causing danger.

This product is not intended for use by children or those with reduced mobility.

Please remove the power plug from the socket after use or before cleaning the product.

Do not touch the power cord and power switch with wet hands.

When a part of the MINI WALK 3 , such as walking belt or rotating scroll bar roll in stuff, turn off the power and clean it.

When the walking belt is running, don't try to turn around.

Keep your position facing front at all times.

It is forbidden to have two or more people on the

MINI WALK 3 at the same time.

It is forbidden to shake the MINI WALK 3 at any time.

Do not press on the handrails with hands to support the body hanging in the air.

In case of emergency, please pat the emergency stop switch and the MINI WALK 3 will stop quickly.

When the handrail is unfolded, in the event of an emergency, hold the handrail of the MINI WALK 3 with both hands, and step on the non-slip side pedal

(side rail) on both sides of the walking belt or on the ground to avoid losing balance and causing a fall.

Do not use this product when the following conditions occur:

The power cord or power plug is damaged; the operation is not normal; the product drops on the ground or is damaged.

In addition to professionals, it is strictly forbidden to adjust the electrical control part of the MINI WALK 3.

Care should be used when mounting or dismounting the treadmill.

Disconnect all power before servicing the treadmill.

Do not exceed maximum specified user weight.

Usage environment

Do not use this product in humid or excessive dusty environment so as to avoid product failure.

Do not use this product at room temperature above

40 °C.

Do not place the product outdoors or near water source.

Do not place the product near electric heaters, stoves or areas with direct sunlight.

Do not place blankets or soft cloth cushions under this product. The heat generated during the operation of the product may cause the blanket or soft cloth pad to be in danger of burning or electric shock..

Operational safety

This product is not suitable for the following people:

Do not use it by those who doctors tell not to exercise, so as to avoid accidents or physical discomfort such as thrombosis, severe aneurysms, acute venous tumors, various dermatitis, skin infections, etc.

It is forbidden to use together with the following medical equipment: Cardiac adjuster implantable medical electronic instruments; medical electronic instruments used to sustain life such as artificial heart.

WARNING

Excessive exercise can cause serious injury or death. Do not exercise too much. If you feel dizzy, stop exercising immediately.

SAVE THESE INSTRUCTIONS

6

Support

Overview

The purpose is to quickly know about the walking machine and understand the meaning of the serial number and symbol of the user manual. It is important to keep this user manual, especially when lending or reselling this machine.

Icon in the user manual

This symbol represents a safety alert that it must be read and followed carefully for the safety of yourself and others and to avoid damaging your walking machine.

This symbol represents the points for attention.

Please read them carefully and observe them to get correct operation and better experience of this walking machine.

Steps

Strictly observe the sequence and follow the steps with serial numbers.

1 .

The first step of the operation.

2 .

The second step of the operation.

List

No mandatory sequential operations are displayed as lists with enumerated items.

The first step

The second step

Timeliness of this user manual

We continue to further develop to ensure that the walking machine has a high level of safety and quality.

Therefore, this walking machine may occasionally differ from the description. (Note: The cover is the regular color matching of the walking machine, the specific color is subject to the color of the purchased model)

Walking machine serial number

Copy the walking machine serial number (located around the power switch) to the serial number field below and then save this user manual.

7

Set Up Your MINI WALK 3

Overview

Be sure to place the walking machine carton on a flat surface. Please be careful to carry it. Never unpack from the side of the carton.

Packing carton specifications

Unpacking

1 .

Make sure the top cover of the carton is facing up and open the top cover.

2 .

Two people are required to remove the walking machine from the box.

Item

Carton size ( mm )

Gross Weight ( kg )

Specifications

1515x756x120

40

Carton inner packaging

Carton cover

Packing filter

Accessories

Walking machine

Carton lower cover

3 .

Place the walking machine on a flat surface. Do not put it on a soft mat or a thick carpet when using it.

8

4 .

Put the filter back into the box , fasten the upper and lower covers of the box and store them .

5 .

We recommend leaving at least 0.5 m of space on both sides of the walking machine and a 2 m safe area behind the walking machine.

0 .

5 M

2 M 0 .

5 M

0 .

5 M

Keep the original box and packing material after unpacking. During the warranty period any MINI WALK

3 exchanges or returns should be returned to the original factory in the original packaging.

Specifications

No .

Description

Unfloding dimension ( mm ) 1430x735x1030

Folding dimension ( mm ) 1475x735x93

Running area ( mm ) 1200x460

Net Weight 35

Max load ( kg ) 120

Applicable ages ( year )

14-60

Lifting slope (%)

Motor power ( W ) 450

Handrail unfolded: 1.0-8.0

Speed range ( km / h )

Handrail folded: 1.0-6.0

Display Specifications White Matrix Digital Display

Motion parameters speed, steps, time, distance

9

Unfold the Handrail

Overview

MINI WALK 3’s handrail uses gas-liquid buffer technology and will automatically unfold when the handrail unfolds and reaches a particular angle.

Use the following steps to unfold the MINI WALK 3 ’s handrail.

A_1

A_3

A_2

A_4

Unfolding steps

1 . To adjust the handrail to unlock mode, move the two-way lock mechanism switch A_1 /A_2 on the left and right sides of the armrest from the LOCK position to the UNLOCK position.

A _1 / A _2

2 .

Raise the armrest A_3/A_4 up to a certain angle with both hands and the armrest will automatically rise to the appropriate height.

A_3 A_4

3 .

When it is finished unfolding, move the bi-directional locking mechanism A_1/A_2 switch from the UNLOCK position to the LOCK position to fix the handrail.

A_1 / A_2

You can adjust the angle of the handrail according to your preferences. Adjust the unfold angle and change the two-way lock mechanism switch to the locked position.

When the handrail is folded, the maximum speed of MINI WALK 3 is 6km/h; when the handrail is in unfolded mode, the maximum speed of MINI WALK 3 is automatically adjusted to 8km/h.

11

Fold the Handrail

Overview

This MINI WALK 3 is fully foldable and requires no installation tools. The handrail uses a gas-liquid cushioning technique when you fold the handrail.

Follow the steps below to fold the walking machine. The thickest section is no more than 10cm when the walking machine is fully folded, it can accommodate any space that meets this size, such as under the sofa or under the bed

(where the space permits).

B_3

B_4

B_1

B_2

Folding step

1 .

To adjust the handrail to unlock mode , rotate the bi-directional locking mechanism switch B_1/B_2 switch on the left and right sides of the handrail from the LOCK position to the UNLOCK position.

B _1 / B _2

2 .

Press the armrest B_3/B_4 to the main body of

MINI WALK 3 . Hold the handrail with both hands while pressing until it’s completely folded.

B_3/B_4

12

3 .

After folding is completed, move the bi-directional locking mechanism B_1/B_2 switch to the UNLOCK position to the LOCK position to lock the handrail.

After folding is completed, move the bi-directional locking mechanism to the locked position so that the handrail and the MINI WALK 3 are fixed tightly together to facilitate moving your MINI WALK 3 .

When the handrail is in the folded state, the maximum speed of MINI WALK 3 is 6km/h; when the handrail is unfolded, the maximum speed of MINI WALK

3 is automatically adjusted to 8km/h.

13

Move the MINI WALK 3

Overview

The net weight of the machine is 35kg. Use the two-way locking mechanism to fasten the body when the handrail is folded to facilitate moving. Please follow the steps below to move MINI WALK 3 .

WARNING

Before moving MINI WALK 3 , remove the power cord plug from the socket and make sure that the handrail lock mechanism switch is in the locked mode.

C_1 C_2

Moving step

1 .

Lift MINI WALK 3 from the handrail C_1 with both hands.

C_1

2 .

Move MINI WALK 3 to the desired position with the two moving pulleys C_2 that under the motor cover.

C_2

14

Power Supply

Grounding instructions

This product must be grounded. If the product fails, grounding provides a minimum resistance path for the current and thus reduces the risk of electric shock. The original plug of this product is equipped with a grounding conductor. For safety reasons, the grounding plug must be plugged into the appropriate socket and the socket must be properly installed and grounded in accordance with all local codes and regulations.

WARNING

Failure to follow the instructions may result in electrical failure.

Never touch the power cord and power switch with wet hands.

Do not remove the motor cover otherwise there is a danger of electric shock.

Power requirement

The normal use voltage of this product is 110(USA/

Canada) / 220(Europe) volts.

The voltage required for MINI WALK 3 can be found on the manufacturer sticker(around the front of the motor cover). It needs to be used according to the specific voltage requirements.

Refer to the following grounding diagram.

Power MINI WALK 3 on and off

Overview

MINI WALK 3 comes with a power cord and a power switch. The power cord and the power switch are located on the right side of the motor cover.

D _ 2 D _ 1

Category Description

D _ 1 Power cord

D _ 2 Power switch

Power switch icon meaning

= on ， = off

Power on

1 .

Power on MINI WALK 3 .

2 .

Press the icon on the power switch D_2.

Power off

1 .

Press the icon on the power switch D_2.

2 .

Pull the MINI WALK 3 power plug out of the socket.

15

Use the MINI WALK 3

Overview

By introducing MINI WALK 3 parts, buttons, remote control (optional) and movement parameters window, you can get familiar with the working principle of different workout modes quickly. MINI WALK 3 has three control modes, namely manual control mode, automatic control mode and remote control mode (optional).

E _ 1

E _ 3

E _ 2

Emergency stop switch

The emergency stop switch is located at E_1.

The long red button is located in the middle of the handrail. When MINI WALK 3 is running if you encounter an emergency, press the emergency stop switch and the MINI WALK 3 will stop quickly.

Press

E _ 6

E _ 5

E _ 4

To restart the MINI WALK 3 , turn off the emergency stop switch and then press the START button on the handrail to start it.

Emergency stop switch disconnected

Close the emergency stop switch

16

Walking belt

The walking belt is located at E_2.

Warm up before the exercise, check the walking belt’s condition prior to use, adjust the tightness and perform the lubrication maintenance of the MINI WALK 3 on time.

Side rail

The side rails are located at E_3/E_4.

The side rails are fixed on both sides of the walking belt allowing you to safely straddle the MINI WALK 3 during start-up or an emergency.

Motor cover

The motor cover is located at E_5.

Do not cover the motor cover to avoid the motor overheating and causing malfunction or damage. Do not step on or jump on the motor cover.

Bluetooth Speaker

The Bluetooth speaker is located at E_6.

Connect the speaker to a phone using the Bluetooth function on the phone, then control the speaker from your phone.

Note: Close the emergency stop switch after power on MINI WALK 3 . If the emergency stop switch is not closed, it will not start normally.

The emergency stop switch button 'EMERGENCY

STOP' will continue to flash.

17

Handrail Buttons

The handrail buttons are used to control: start, pause, stop, acceleration, deceleration, and switch motion modes.

SPEED SWITCH START

EMERGENCY

STOP

F_1

STOP PAUSE SPEED

The function button panel is at F_1.

SPEED

SWITCH

Deceleration button

Press this button to decrease the speed in increments of 0.1km/h.

Long press this button to rapidly reduce the speed.

Mode Switch button

Switch between manual control mode and automatic control mode.

START

Start button

Start MINI WALK 3 and enters a manual control mode.

STOP

PAUSE

Stop button

MINI WALK 3 gradually decelerates to stop and the display is cleared.

Pause button

Pause MINI WALK 3 , clears the speed value and retains the display parameters.

SPEED

Acceleration button

Press this button to increase the speed in increments of 0.1km/h

Long press this button to rapidly increase the speed.

18

Display Window

Power on MINI WALK 3 , turn on the power switch, and the display will illuminate. The display window uses white matrix numbers to display the speed, number of steps, time, and mileage motion parameters, and simultaneously displays the two operational modes.

G_1

The sports parameter display window

Name

SPEED

STEPS

TIME

DIST

Description

Speed ( handrail unfold status)

Display range

1.0km

/ h 8.0km

/ h

Speed (handrail folding state)

Display range

1.0km

/ h 6.0km

/ h

Number of steps

Display Range

0 99999steps

Time

Display range

00 : 00 99 : 59

Distance

Display range

0km 99 .

99 km

A

M

Automatic control mode

Manual control mode

Remote control mode(optional)

SPEED

Displays the current speed value;

Pauses or stops MINI WALK 3 , and the value is cleared.

STEPS

Displays the cumulative number of steps in a single exercise;

Pause MINI WALK 3 , the value remains, if you restart MINI WALK 3 , and it does not enter sleep mode, the display continues to accumulate.

The value is cleared after stopping MINI WALK 3 .

TIME

Shows the duration of a single exercise;

If you pauses the MINI WALK 3 , the parameters

remain, if you restart MINI WALK 3 , and it does not enter sleep mode, the display continues to accumulate.

The parameters are cleared after stopping the

MINI WALK 3.

DIST

Displays the accumulated mileage of a single exercise;

If you pause the MINI WALK 3 , the parameters

remain, if you restart MINI WALK 3 , and it does not enter sleep mode, the display continues to accumulate.

19

Remote Control(Optional)

The remote control optional. Use it to control: start, stop, acceleration, deceleration and switch motion modes.

H_1

H_2

H_4

H_5

H_3

H_6

H_8

Front of the remote control

Key Function

Name Description

H_1 Status indicator light

H_2 Acceleration button

H_3

Deceleration button

H_4

Start/stop composite button

H_5

M ode switch button

H_6/H_7 Wireless transmission indicator

H_8 Battery cover

Status indicator light

Press the remote control button and the indicator light turns on.

Acceleration button

Press the acceleration button, the speed value is first rounded up by a multiple of 0.5km/h and when you press it again the speed is incremented by 0.5km/h.

Deceleration button

Press the acceleration button, the speed value is first rounded up by a multiple of 0.5km/h and when you press it again the speed is decremented by 0.5km/h.

Mode switch button

Used to switch between manual control mode and automatic control mode.

H_7

Back of the remote control

Remote control matching steps

You will need to match the remote control with the

MINI WALK 3 the first time you use it, the matching operations are as follows:

1. Power off the MINI WALK 3 ;

2. Power on the MINI WALK 3 and turn on the power switch, at the same time, press and hold any button on the remote control for more than 5 seconds;

3. MINI WALK 3 will react and show the following figure on the display window:

4.Wait until the figure above appears on the MINI

WALK 3 ’s display window. If it is not successful, repeat these steps.

Battery cover

MINI WALK 3 ’s remote control uses two batteries

(1.5V NO.7 AAA alkaline battery).Replacing the remote control’s batteries is the same as replacing a normal TV remote control’s batteries.

20

Manual Control Mode

Manual control mode provides the user to control

MINI WALK 3 with the handrail buttons.

Operation

Start

Power on MINI WALK 3 , turn on the power switch, press the handrail’s “Start” button to start MINI WALK

3 , start walking slowly and accelerate.

Acceleration

Press the “Acceleration” button on the handrail.

Each time you press it, the speed increases by 0.1km/h.

When you long press it, the speed increases rapidly until the maximum speed reaches 8km/h.

Deceleration

Press the “Deceleration” button on the handrail.

Each time you press it, it will reduce the speed by

0.1km/h. When you long press it, the speed will decrease rapidly until the minimum speed reaches 1km/h.

Pause

Press the handrail’s “Pause” button to pause and gradually slows down to stop.

Stop

Press the handrail’s “Stop” button to gradually slow down to stop.

Switch modes

Press the handrail’s “Mode Switch” button to switch the motion mode. There are two states:

When MINI WALK 3 is in the manual control mode, press the “Mode Switch” button and MINI WALK 3 will switch to automatic control mode.

When MINI WALK 3 is in the automatic control mode, press any button on the handrail or remote control (optional), and MINI WALK 3 will switch to manual control mode and execute the corresponding button command.

No-load function

After starting the MINI WALK 3 , if you do not walk on it for 10 seconds, it stops automatically.

Note:

After starting the MINI WALK 3 , start walking.

Beginners should accelerate slowly.

When using the buttons, hold the handrail with one hand.

In case of emergency, press the emergency stop button, MINI WALK 3 stops quickly, hold the handrail after lowering the speed.

To stop the exercise, press the stop button. Hold the handrail firmly. After the speed has slowed down, place your feet on the side edges.

21

Remote Control Mode(Optional)

The remote control is optional, it allows you to control

MINI WALK 3 ’s running mode using the remote control.

Operation

Switch modes

Press the “Mode Switch” button on the remote control to switch the exercise mode. There are two states at this point:

When the MINI WALK 3 is in manual control mode, press the “Mode Switch” button on the handrail or remote control (optional), the MINI

WALK 3 switches to the automatic control mode.

When the MINI WALK 3 is in the automatic control mode: press any button of the handrail or remote control (optional), the MINI WALK 3 switches to the manual control mode and runs the corresponding button command.

Start

Press the remote “Start/Stop” combination button to start or stop the MINI WALK 3

When

. There are two states:

MINI WALK 3 is in the standby mode: press the “Start/Stop” combination button to start the

MINI WALK 3 .

When MINI WALK 3 is in operation:

Press the “Start/Stop” combination button to stop the

MINI WALK 3 .

Acceleration

Press the “Acceleration” button on the remote control.

Each time you press it, the speed value is rounded up in multiples of 0.5km/h. Press again, the speed is increased by 0.5km/h, the maximum speed of the MINI

WALK 3 without handrail is 6km/h, and the maximum speed of the walking machine with handrail is 8km/h.

Deceleration

Press the “Deceleration” button on the remote control.

Each time you press it, the speed value is first rounded up in multiples of 0.5km/h. Press again and the speed is reduced by 0.5km/h until the minimum speed is 1km/h.

22

Automatic Control Mode

Automatic control mode uses AUTO RUN2.0 intelligent speed control system that controls MINI

WALK 3 ’s running mode without buttons.

Start

1 .

Continuously walk 3 steps from the back of the walking belt at a normal walking pace. Maintain 5-

10cm space between each foot as shown in the figure.

Motor cover

Walking operation

Motor cover

Deceleration zone Speed keeping zone Acceleration zone

Accelerating

When your body’s center of gravity is located in the acceleration zone of the walking belt, keep moving in this area to maintain automatic acceleration as shown in the below figure:

The center of the body is in the acceleration zone:

Motor cover

Step 1 Step 2 Step 3

The display shows that the content is synchronized with steps, as shown in the figure: step 1 : step 2 : step 3 :

2 .

After completing the three steps, the MINI WALK

3 starts running in automatic mode and records the movement data.

The center of gravity (blue line)is located in the

acceleration zone

Uniform speed

Keep your center of gravity in the holding area.

Keep moving in this area and maintain a constant speed as shown in the figure. The center of gravity is in the retention zone.

Motor cover

The gravity center of the human body (blue line)

is located in the speed keeping area

23

Deceleration

When your body’s center of gravity is located in the deceleration area of the walking belt, keep moving in this area to maintain automatic deceleration as shown in the below figure:

Motor cover

The gravity center of the human body

(blue line) is located in the deceleration zone

Deceleration from the Acceleration zone

When your center of gravity moves from the

Acceleration zone to the Retention zone and you continue to walk, MINI WALK 3 automatically decelerates and then maintains a constant speed.

Deceleration from the Retention zone

When your center of gravity moves from the Retention zone to the Deceleration zone and you continue to walk,

MINI WALK 3 automatically decelerates to the lowest speed and then stops.

Switch modes

When MINI WALK 3 is in Automatic control mode: press any button on the handrail or remote control

(optional), MINI WALK 3 cancels automatic control mode and runs the corresponding button command.

Stop operation

Stop from the Acceleration zone

When your center of gravity moves from the

Acceleration zone and enters the Retention zone, and then slows down from the Retention zone into the

Deceleration zone and you continue to walk, the MINI

WALK 3 automatically decelerates to the lowest speed and stops.

Stop from the Retention zone

When your center of gravity moves from the Retention to the Deceleration zone and you continue to walk, the

MINI WALK 3 automatically decelerates to the lowest speed and then stops.

Note:

Automatic control mode requires learning and adaptation.

When you first use Automatic control mode , you need to control it when the handrail is in Unfold mode. If you encounter an emergency during operation, press the Stop button or the Emergency stop switch, and MINI WALK 3 cancels Automatic control mode and stops.

You can use this mode completely without the handrail buttons or remote control and we recommend it for users with better motor coordination or experience with a treadmill.

Orthotic insoles or high heels are not suitable for this mode .

24

Sleep and wake up

After MINI WALK 3 is powered on, if you do not use the function buttons for a long time or walk on the walking belt, MINI WALK 3 automatically enters

Sleep mode. If you need to continue using it, you can wake up MINI WALK 3 by pressing the function buttons or touching the walking belt with the sole of your foot.

Sleep

If you do not use MINI WALK 3 function button or walk on the walking belt, the system enters Sleep mode after the standby time exceeds 5 minutes, and the display window shows:

During the wake-up process, the middle area of the display will change with the number of touches, as shown below:

First it looks like:

Second it looks like:

Third it looks like:

Wake up operation

There are two ways to wake up MINI WALK 3 :

Press any function button on the handrail, then the parameters of the display window illuminates, the button light turns on and MINI WALK 3 wakes up.

Raise your foot and continuously touch the walking belt at a constant speed. It takes three taps to wake up the MINI WALK 3 . The time between two touches can be no more than 5 seconds as shown in the figure:

After correctly tapping the walking belt three times, the display window lights up the parameters, the handrail button light is on, and MINI WALK 3 is awake.

The following actions will not wake up MINI

WALK 3

Wake up action error: The foot should be in the same direction as a step on the MINI WALK 3 . If the foot is perpendicularc to the direction of motion, the wake up fails.

Wake-up time error: Use the sole of the foot to continuously touch the walking belt with a constant speed. The wake-up fails if the interval between every two touches exceeds 5 seconds.

25

Bluetooth Speaker

MINI WALK 3 is equipped with a Bluetooth speaker, which connects to cell phones through the Bluetooth function of the phone. You can control the speaker through the phone. It supports phones or tablets with

Bluetooth capability.

Pair with a phone

Use the speaker

You can control the playback of songs with a mobile phone or tablet with Bluetooth.

Operation Steps:

1 .

Power on MINI WALK 3 , turn on the power button on the motor cover and wait for the phone to pair.

2 .

Enter the phone settings interface, select the “

Bluetooth” icon and turn on the Bluetooth function

3 .

After the Bluetooth function is turned on, click the

Bluetooth speaker name in the devices available to pair.

Problems and Troubleshooting

If the Bluetooth device can not connect to MINI

WALK 3 , there are three troubleshooting solutions:

Power on MINI WALK 3 , wait 10 seconds, restart, and then refresh the pairing;

Delete the Bluetooth device and refresh the pairing again. Click the Bluetooth speaker name of the MINI WALK 3 and enter the pairing code again,

The pairing code is 1234 or 0000.

Check if another device has successfully

connected to the Bluetooth speaker.

4 .

After clicking the Bluetooth speaker name, enter the pairing code: 1234 or 0000. Wait for the MINI

WALK 3 to pair. When the Bluetooth connection is successful, there will be a “ding-dong” tone.

26

Maintainance

Centering the Walking Belt

Before the shipment, the walking belt on the walking machine has been adjusted to be centered for you.

During the transportation process, the walking belt may be off-center. Before you start using the walking machine, you must ensure that the walking belt is already centered to ensure smooth running of the walking machine.

Safety Tips

It is forbidden to operate the walking machine

during adjustment.

Steps

1 .

If the walking belt is shifted to left side, use the

L-shaped hex wrench to turn the adjustment bolt on the left side clockwise by 1/4 turn, and operate it to the speed of about 3km/h. After running for 1 minute, observe whether the walking belt is centered. If the walking belt is moved to the right, turn the adjusting bolt counterclockwise by 1/8 turn. Repeat the above actions until the walking belt is centered.

The walking belt is shifted to right side

Note: If there is still a problem during the adjustment process, please contact after sales service.

The running belt is shifted to left side

2 .

If the walking belt is shifted to right side, use the Lshaped hex wrench to turn the adjusting bolt on the right side clockwise by 1/4 turn, and run to the speed of about 3km/h. After running for 1 minute, observe whether the walking belt is centered. If the step is moved to the left, turn the adjusting bolt counterclockwise by 1/8 turn. Repeat the above actions until the walking belt is centered.

27

Add Lubricant

The running board and walking belt of MINI WALK 3 have been pre-coated with lubricating silicone oil.

The friction between the running board and the walking belt has a great influence on the service life and performance of the walking machine, so it is necessary to apply lubricating oil regularly. Apply about 20 grams each time and be sure to apply evenly.

We recommend that the running board and the walking belt of the walking machine be lubricated with silicone oil (for reference only) as follows:

Once every 6 months for users with less use times

(less than 3 hours per week) ;

Once every 3 months for users with moderate use times(3-5 hours per week);

O nce every month for users with frequently use times(more than 5 hours per week);

Warning

When you lubricate the walking belt, you need

to turn off the walking machine. Then unplug the power cord from the power socket.

Lubrication step

1 .

Lift the walking machine from the side and tilt it at an angle of 45 degrees.

2 .

Open the walking belt by hand, pour the lubricating silicone oil on the front, middle and back of the running board, let the lubricating silicone oil flow down to the other side of the walking belt until it flows to exceed the middle of the running board, and then lay flat the machine. Repeat this step to lubricate the other side of walking belt and running board.

Walking belt

Running board

Storage

When not in use, please store the product in a safe, dry, ventilated and cool place.

Do not twist the power cord.

Avoid sharp objects scratching the surface of the product.

Do not place the product under direct sunlight or high temperatures.

Cleaning

Warning

Be sure to unplug the machine's power cord of walking machine before cleaning or maintaining the product.

Use a cloth to clean the surface of the product.

Comprehensive cleaning will extend the life of the walking machine.

Remove dust regularly to keep parts clean. Sweep the exposed parts of walking belt both sides, this will reduce the accumulation of impurities under the walking belt. Keep the sneakers clean, avoid carrying foreign objects into the walking belt, so as to avoid wearing the walking belt and running board.

The surface of the walking belt must be wiped with a damp cloth dampened with soap. Be careful not to spill water under the electrical components and the walking belt.

Note: Do not damage the electrical components or break the control line.

Running board

Silicone oil bottle

Silicone oil

3 .

After finishing the lubrication step, and starting up, walk slowly for a few minutes to ensure that the walking belt and the running board fully absorb the lubricating silicone oil before starting to increase the speed.

28

Troubleshooting

Error code Possible reason Solution

ERR 02 Burst protection Replace the controller or check the motor cable

ERR 05 Overcurrent protection Walking with excessive frictional resistance, need to

add oil; or controller is damaged

ERR 06

Overload protection Walking with excessive frictional resistance, need to

add oil; or controller is damaged

29