Bissell LIFT-OFF SPINPOWER User`s guide

USER’S GUIDE
3760 SERIES 220-240V
3
Safety Instructions
4
Product Diagram
4-6 Assembly Instructions
6-9 Operation / Special Tools
10-13 Maintenance
14
15
15
16
Troubleshooting
Replacement Parts
Consumer Services
Warranty
ug603-5570_3760E_1105.indd 1
2/2/06 4:12:08 PM
Thanks For Buying A BISSELL Lift-Off™ Spinpower
We’re glad you purchased a BISSELL Lift-Off Spinpower vacuum.
Everything we know about floor care went into the design and construction
of this powerful, high-tech home vacuuming system.
Your BISSELL Lift-Off Spinpower vacuum is well made, and we back it with
a limited comprehensive two-year warranty. We also stand behind it with a
knowledgeable, dedicated Consumer Services department, so, should you
ever have a problem, you’ll receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today, BISSELL
is a global leader in the design, manufacture, and service of high quality
homecare products like your BISSELL Lift-Off Spinpower vacuum.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
President and Chief Executive Officer
2
ug603-5570_3760E_1105.indd 2
2/2/06 4:12:09 PM
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance,
basic precautions should be observed,
including the following:
■ Remove plug from electrical outlet before clean-
READ ALL INSTRUCTIONS
BEFORE USING YOUR
UPRIGHT VACUUM.
replaced by the manufacturer or its service
agent in order to avoid a hazard.
■ Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, petrol, etc.).
■ Do not allow to be used as a toy.
■ Do not use for any purpose other than
described in this User’s Guide.
■ Use only manufacturer’s recommended attachments.
■ Do not use with any opening blocked; keep
free of dust, lint, hair, and anything that may
reduce air flow.
■ Keep appliance on a level surface.
■ Turn off all controls before unplugging.
■ Be extra careful when cleaning stairs.
■ This appliance is provided with double
insulation. Use only identical replacement
parts.
■ Do not use without debris tank and/or filters
in place.
■ Pay close attention when working
around children.
WARNING:
To reduce
the risk of fire, electric shock,
or injury:
■ Use indoors only.
■ Do not leave machine when it is plugged in.
■ Do not use with damaged cord or plug.
■ If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into
water, return it to a service agent.
■ Do not handle unit with wet hands.
■ Do not pull or carry by cord, use cord as a handle,
close door on cord, pull cord around sharp
corners or edges, run appliance over cord, or
expose cord to heated surfaces.
■ Do not unplug by pulling on cord. Unplug by
grasping plug.
■ Do not run appliance over cord.
■ Do not handle plug or appliance with wet hands.
■ Do not expose hair, loose clothing, fingers or
body parts to openings or moving parts.
■ Do not pick up hot or burning objects such as
cigarettes, matches, or hot ashes.
■ Do not pick up flammable or combustible materials
(lighter fluid, petrol, kerosene, etc.) or use in the
presence of explosive liquids or vapour.
■ Do not use appliance in an enclosed space filled
with vapours given off by oil base paint, paint
thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapours.
■ Not intended for use by young children or infirm
persons without supervision.
■ Young children should be supervised to ensure that
they do not play with the appliance.
ing or maintaining the appliance.
■ If the supply cord is damaged, it must be
SAVE THESE
INSTRUCTIONS.
THIS MODEL IS FOR HOUSEHOLD USE ONLY.
IMPORTANT
FOR OPERATION ON A 220-240 VOLT A.C. 50/60
Hz POWER SUPPLY ONLY.
FOR RESIDENTS OF THE
UNITED KINGDOM ONLY
If your appliance is fitted with a nonrewireable
BS 1363 plug it must not be used unless a 13
amp (ASTA approved to BS 1362) fuse is fitted in
the carrier contained in the plug. (Spares may be
obtained from your BISSELL supplier). If for any
reason the plug is cut off, it must be disposed
of, as it is an electric shock hazard should it be
inserted into a 13 amp socket.
3
ug603-5570_3760E_1105.indd 3
2/2/06 4:12:10 PM
Handle
Comfort Grip
Cord Clip
Dusting Brush/
Upholstery Tool
Release Button
Stretch Hose
Power Switch
Hose Clip
Quick Release
Cord Wrap
Upper Tank Knob
Brush On/Off
Switch
Detachable Cylinder
Twist n' Snap™
Hose Connection
Clean Filter
Indicator (Select
Models Only)
Crevice Tool
Metal
Telescoping
Extension Wand
HEPA Media
Post-Motor Filter
Power Cord
Louvers/Filter
Frame
Upper Tank Filter
(Inside Louvers)
Hose Grip
Dirt
Container
Handle Release
Pedal
Pre-Motor
Filter
Hose Grip Base
Upper Tank
Dust Chamber
with Screens
Lock ’n Seal™
Lever
Height
Adjustment
Knob
Powerfoot
CAUTION:
Do not plug in your vacuum
4
Furniture
Protection
Guard
cleaner until you are familiar
with all instructions and
operating procedures.
ug603-5570_3760E_1105.indd 4
2/2/06 4:12:10 PM
How To Use This Guide
This User’s Guide has been designed to help
you get the most satisfaction from your BISSELL
Lift-Off Spinpower vacuum. You’ll find assembly and
operating instructions, safety precautions, as well as
maintenance and troubleshooting instructions. Please
read this User's Guide thoroughly before assembling
your vacuum cleaner.
Pay particular attention to the product diagram,
assembly instructions, and part names. Locate and
organize all parts before assembly. Familiarize yourself
with the parts and where they fit. Following this User’s
Guide will greatly enhance your ability to get the most
performance from your BISSELL Lift-Off Spinpower
vacuum for many years.
WARNING:
Plastic film can be
dangerous. To avoid danger
of suffocation, keep away
from babies and children.
How To Put It Together
The only tool you’ll need to assemble your vacuum
cleaner is a screwdriver.
Attach Handle To Vacuum
1. Locate the vacuum Handle and remove the screw
packet taped to the base of the Handle.
2. Stand the vacuum upright and slide the base of
the Handle firmly into the grooves at the top of the
vacuum body.
3. Check to be sure the Handle is fitted to the vacuum
body. If there is a gap in front, continue to push firmly
until the Handle is flush.
4. Insert the two screws from the screw packet into the
existing holes. Tighten securely with a screwdriver.
Attach Vacuum Hose and Tools
™
1. Position the Twist ‘n Snap Hose assembly on the
vacuum and line up the tabs on the base of the hose
with the corresponding notches. Turn the Twist ‘n Snap
Hose to the right to lock into place.
2. Slide the end of the Hose Grip onto the Hose Grip Base.
Place the Hose into the Hose Clip.
NOTE: The Powerfoot will not operate effectively
unless the Hose is firmly attached to the base.
5
ug603-5570_3760E_1105.indd 5
2/2/06 4:12:11 PM
Attach Vacuum Hose and Tools Continued
Combination
Tool
3. Snap the Metal Telescoping Extension Wand, Crevice
Tool, and Combination Tool into storage clips as shown.
™
4. On Board TurboBrush (Select Models Only)
The TurboBrush Bracket slides onto the Hanger on
the front of the Handle. Attach the Bracket by
aligning the slots with the rectangular part on the
Hanger as shown and pulling down until it is locked
into place.
Note: If you do not wish to store the TurboBrush Crevice Tool
on your Lift-Off vacuum, the Bracket may be
hung on a wall for storage and the Hanger may
be removed from the vacuum.
Place the TurboBrush in the Bracket by aligning
the small holes near the brush roll with the tabs
at the bottom of the Bracket and snap the TurboBrush
into place.
Metal
Telescoping
Extension
Wand
TurboBrush™
How To Use Your Lift-Off Spinpower
Power Switch/Brush Switch
The Power Switch is located just below the handle
on the front of the Detachable Cylinder. Push the
rocker switch “ON” (I) to vacuum, and “OFF” (O)
when cleaning is complete.
The Brush Switch is located just below the handle
on the front of the Detachable Cylinder next to
the Power Switch. This switch turns the Rotating
Brush on and off. The Brush Switch should be in
the “ON” (I) position for normal carpet cleaning.
You may want to turn the Brush Switch “OFF” (O)
for bare floor cleaning or other delicate surfaces.
CAUTION:
Before using your vacuum, make
sure that the Dirt Container and
Upper Tank are in locked position
and that all Filters (Upper Tank,
Pre-Motor and Post-Motor) are
in place. Do not operate your
vacuum without these Filters.
Brush
Power
Note: Your BISSELL Lift-Off Spinpower vacuum
is equipped with a special internal switch that
turns the Rotating Brush off whenever the unit is
in the Upright Position.
Handle Positions
1. Upright – For storage and above floor cleaning with tools.
2. Normal Cleaning – Press the Handle Release Pedal
with your foot to recline.
Tip:
Your vacuum features a Quick-Release
Cord Wrap. To remove the Power Cord
quickly and easily, rotate the Upper Cord
Wrap towards floor, and slip Power Cord
from Upper and Lower Cord Wraps.
6
ug603-5570_3760E_1105.indd 6
2/2/06 4:12:12 PM
Power Height Adjustment
The Powerfoot on your BISSELL Lift-Off Spinpower
vacuum can be adjusted to clean several floor surfaces.
NOTE: For optimal cleaning performance, adjust to
the lowest practical setting. If your cleaner is
difficult to push, adjust to the next higher setting.
Tip:
Before cleaning under
low furniture, check
area first for objects
that might harm the
unit or block the
Vacuum Hose.
1. Place Handle in Upright Position.
2. Turn Height Adjustment Knob to desired setting.
Lowest Setting
– For bare floors.
Medium Settings – For short and medium
pile carpets.
Highest Setting – For plush pile carpet.
NOTE: You may also adjust the setting while in the Normal
Cleaning Position.
ATTENTION BERBER
CARPET OWNERS:
Some Berber Carpets have a tendency
to fuzz with wear. Repeated passes
with your vacuum over the same area
may aggravate this condition. Consider
using the highest height setting or
turning off the Rotating Brush for this
type of carpet.
Special Tools
Your BISSELL Lift-Off Spinpower vacuum is not only
a powerful floor vacuum cleaner, it’s also a versatile
stairs and above floor vacuum when you select one of
the special tools.
Note: The tools can be used with the
vacuum in the Upright Position or with the
Detachable Cylinder.
1. Detach the Vacuum Hose by grasping the Hose Grip and
lifting to separate from the Hose Grip Base.
2. Attach tools by firmly pushing onto Vacuum Hose or Metal
Telescoping Extension Wand.
Combination Dusting Brush/Upholstery Tool:
Two types of cleaning tools are included in one attachment;
rotate for desired tool.
■ Use Brush side to dust furniture, blinds, books, lamps,
shelves, and baseboards.
■ Use Upholstery side for curtains, draperies, cushions,
and fabrics.
CAUTION:
Always place vacuum cleaner on
floor in its fully Upright Position
and make sure it is locked into
place before removing Cylinder
or when using tools. Placing
the Lift-Off Spinpower in its full
Upright Position automatically
stops the rotating brush.
Crevice Tool:
Use in tight narrow spaces.
Metal Telescoping Extension Wand:
Use with desired attachment for a longer reach.
To extend the Wand, grasp the collar and push away
from you. The collar will automatically lock into place. To
retract, pull the collar toward you. The collar will
automatically relock.
Stair Cleaning Tool (Select Models):
Use for stairs, area rugs, and other small carpeted areas.
This tool can also be used for bare floors.
Note: The Stair Cleaning Tool does not store on board.
ug603-5570_3760E_1105.indd 7
7
2/2/06 4:12:13 PM
Special Tools Continued
TurboBrush™ (Select Models):
Use rotating brush action for small areas such as stairs
and upholstery.
Note: Press gently when using TurboBrush to gain
maximum cleaning. Too much pressure could cause
the brush to stop rotating.
Deluxe Bare Floor Tool (Select Models):
Use for bare floors. Swivel head turns to get into tight
spaces and fits under cabinets.
Note: The Deluxe Bare Floor Tool does not store
on board.
All items may not be included with your model. More
tools are available; to order please refer to page 15.
Cleaning With The Detachable Cylinder
Release
Button
The Detachable Cylinder feature makes it possible
to easily take the powerful cleaning action of your
BISSELL Lift-Off Spinpower to stairways, auto interiors,
and other hard-to-reach areas of your home.
Before detaching the Cylinder, your vacuum must be
in its fully Upright Position. You do not need to turn
off the power first.
1. Press the Release Button at the top of the Cylinder
Handle and lift the Cylinder to remove.
2. Detach the Vacuum Hose from the Hose Grip Base at
the back of the Cylinder.
3. Attach the desired tool(s) to the Hose Grip at the end of
the Vacuum Hose.
4. When you’re done, remove the tool(s) and reconnect the
Hose to the Hose Grip Base.
5. Return the Cylinder to the Powerfoot by aligning the
“feet” on the front with the bumps on the foot of the
upright vacuum. Push the Cylinder toward the vacuum
frame until it “clicks” into place.
Clean Filter Indicator
8
Select Models Only
The Clean Filter Indicator tells you when airflow in
the vacuum is reduced due to dirty Filters or a clog
in the hose. The Clean Filter Indicator will remain
green until the airflow is reduced. At that time, it
begins to change to red. When it is fully red, the
airflow is significantly reduced or blocked. Follow
the steps on pages 10 -11 to clean your Filters.
All Filters in the vacuum should be cleaned or
replaced when the Clean Filter Indicator turns red.
If the indicator remains red after all Filters have
been cleaned, follow the steps on page 13 to
check for and clear clogs.
ug603-5570_3760E_1105.indd 8
NOTICE:
While vacuuming, certain
carpets and low humidity
conditions may generate small
static discharges. The discharges
are entirely harmless and are not
associated in any way with the
main power supply.
2/2/06 4:12:15 PM
Shoulder Strap
Buckle
Select Models Only
The Shoulder Strap may be used while cleaning with the
Detachable Cylinder.
1. To attach the Shoulder Strap, wrap the Velcro ends attached to the
bottom of the strap securely around the Cylinder handle as shown.
To obtain maximum strength, overlap the loose ends completely
and press securely in place.
2. The plastic Buckle must be positioned on top of the Cylinder
Handle as shown in the illustration.
3. The length of the strap may be adjusted as required for comfort.
CAUTION:
To reduce the risk of the Shoulder
Strap coming loose in operation,
follow these instructions.
Power Cord Storage
When you are done using your BISSELL Lift-Off
Spinpower vacuum, return it to the Upright Position
and store the Power Cord.
1. Turn vacuum cleaner off (O).
2. Unplug Power Cord by grasping the plug
(NOT the cord) and disconnect from outlet.
3. Loop Power Cord around Cord Wraps on side of
the Cylinder.
CAUTION:
While the vacuum is in
use, warm air is emitted
through the Post-Motor
Filter on the back of the
Cylinder. The bottom of the
Cylinder may also become
warm. When using the
Shoulder Strap, to avoid
discomfort, position the
Cylinder so that these
parts are not directed
towards or touching
your body.
Transporting Cleaner
1. To move your vacuum cleaner from room to room, put the
Handle in the Upright Position, tilt the vacuum back on its
rear wheels and push forward.
2. The vacuum can also be moved by using the Carrying
Handle on the Detachable Cylinder.
CAUTION:
Do not press the Release Button
while using the Carrying Handle to
transport the vacuum cleaner. The
Cylinder could detach causing
the rest of the vacuum to fall.
Carrying Handle
9
ug603-5570_3760E_1105.indd 9
2/2/06 4:12:16 PM
How to Maintain Your BISSELL Lift-Off Spinpower
To maintain maximum cleaning performance, the
following maintenance steps must be performed:
1. Empty the Dirt Container when the dirt reaches the “Full” line
on the front.
WARNING:
To reduce the risk of electric
shock, turn Power Switch
OFF and disconnect plug
from electrical outlet before
performing maintenance or
troubleshooting checks.
2. Check the Upper Tank and Pre-Motor Filters at least once a
month and clean and replace as needed.
3. Replace the HEPA Media Post-Motor Filter every six months.
NOTE: More frequent Filter cleaning may be necessary
if you are vacuuming new carpet, fine dust, or have
allergy concerns.
Follow the instructions on the following pages to
perform these simple maintenance steps.
Tip:
For maximum cleaning
performance, check and
clean or replace all Filters
as suggested.
Empty Dirt Container
The Dirt Container needs to be emptied when the dirt
reaches the “Full” line on the front of the Container.
1. Unplug cleaner from electrical outlet.
Full Line
2. Slide the Lock ‘n Seal Lever to the “Unlock” position.
3. Grasp handle and pull the Dirt Container straight out to
remove from vacuum.
4. Empty dirt into garbage container.
Unlock
Position
Lock
Position
5. Put the Dirt Container back in the vacuum and slide the lever
to the “Lock” position.
Note: The Screens may also be removed from the side Dust
Chambers when you empty or clean the Dirt Container. The
Screens are made to fit each Dust Chamber. If they do not
slide down completely, try in the opposite Dust Chamber.
The Screens will also not fit if there is debris in the track.
The Dirt Container and Screens may be washed in warm
water with a mild detergent. Make sure they are completely
dry before replacing.
Screen
Cleaning The Upper Tank & Filter
Use only BISSELL Style 8 Replacement Filters in your
BISSELL Lift-Off Spinpower.
1. Unplug the cleaner from electrical outlet.
2. The Upper Tank Filter can be reached by removing the Dirt
Container, reaching underneath the Upper Tank and turning the
rim of the Filter Frame to unlock. Pull straight down to remove.
Brush the dirt off the Louvers and Upper Tank Filter.
3. The foam Upper Tank Filter may be removed and hand washed
in cold water with mild detergent. Rinse well then air dry
thoroughly before replacing.
4.
10
Upper
Tank
The Upper Tank and Louvers may also be wiped clean with a damp cloth.
Knob
Note: For easier access, the entire Upper Tank may be
removed by turning the knob on the back of the cleaner to
unlock and pulling the entire tank straight out.
ug603-5570_3760E_1105.indd 10
2/2/06 4:12:17 PM
Cleaning The Pre-Motor and Post-Motor Filters
Use only BISSELL Style 8 Replacement Filters in your
BISSELL Lift-Off Spinpower.
1. Unplug the vacuum from electrical outlet.
Pre-Motor Filter
2. The Pre-Motor Filter protects the motor from dirt particles. It
is located in the slide out tray underneath the Dirt Container.
If the Filter becomes dirty, pull out the tray, lift out the Filter
and clean. This Filter may be hand washed in cold water
with mild detergent. Rinse well and air dry thoroughly
before replacing.
HEPA Media
Post-Motor Filter
3. The HEPA Media Post-Motor Filter assists in the
filtration process to return clean air to the room. It is
located behind the door on the back of the cleaner. If the
Filter becomes dirty, open the door, remove the Filter and
replace. The HEPA Media Filter is not washable.
WARNING:
Do not operate cleaner
with damp or wet
Filters or without all
Filters in place.
Rotating Brush and Drive Belt Maintenance
Use only BISSELL Style 8 Replacement Belts (#3200)
in your BISSELL Lift-Off Spinpower.
Check your vacuum cleaner’s Rotating Floor Brush and
Drive Belt regularly for debris, wear or damage. Debris
can wrap around the brush and hamper its ability to
effectively clean your carpet.
Caution:
To reduce the risk of injury
from moving parts, turn
off vacuum cleaner and
disconnect Power Plug
from electrical outlet.
1. Unplug cleaner from electrical outlet.
2. Remove Detachable Cylinder from vacuum cleaner.
3. Recline Handle and turn vacuum cleaner over so bottom
side is up.
4. Remove the six screws as shown with a Phillips
head screwdriver. Lift the Brush Cover off.
5. Lift the Rotating Floor Brush to remove. Clean strings,
hair and other debris from the Brush, paying special
attention to the Brush Ends.
6. Check Air Passageway for obstructions. Remove any
debris from this area.
7. Clean debris from the Motor Pulley and Drive Belt areas.
8. Check Drive Belt carefully for wear, cuts or stressed areas. If
any damage is present, discard old Drive Belt and replace.
Motor
Pulley
Air
Passageway
11
ug603-5570_3760E_1105.indd 11
2/2/06 4:12:18 PM
Rotating Brush and Drive Belt Maintenance Continued
9. Place one end of the new Drive Belt over Motor Pulley and the
other end over the Brush in the space between the bristles.
10. Pull the Brush firmly to stretch the Drive Belt and place ends
of Brush down into slots on sides as shown. Turn Brush
several times by hand to center the Drive Belt.
11. Reposition Brush Cover and screws. Tighten
screws securely.
WARNING:
To reduce the risk of electric
TurboBrush Maintenance
Select Models Only
The TurboBrush should be checked regularly for clogs
or debris wrapping around the Brush Roll.
1.
Unplug vacuum from electrical outlet.
2.
If a clog is present or debris is visible, unscrew the two
screws on the back of the TurboBrush to remove the
faceplate and clear any obstructions.
3.
To clean debris from the Brush Roll, remove the screw
located on the Belt Cover. Lift the Belt Cover. Remove the
Brush Roll from the Drive Belt and clean debris.
4.
Reposition the drive belt on the Brush Roll. Place ends
of Brush Roll in slots on sides as shown. Reposition Belt
Cover and secure with shorter screw. Reposition faceplate
and secure with two longer screws.
shock, turn Power Switch
OFF and disconnect plug
from electrical outlet before
performing maintenance or
troubleshooting checks.
Belt Cover
12
ug603-5570_3760E_1105.indd 12
2/2/06 4:12:19 PM
Clearing Clogs
Low suction or poor pickup may be due to a clog
in the vacuum cleaner. If you notice a change in
the sound of the motor or a reduction in the
spinning action, check for clogs.
1. Unplug cleaner from electrical outlet.
2. Empty Dirt Container.
Suction
Inlet
3. Check Upper Tank for build up or clogs.
4. Remove the Upper Tank and check the suction inlet for
a clog.
5. Grasp the Hose Grip and lift to separate from the suction
opening. Check for a clog in the Base or the Hose.
6. Release the Twist n' Snap hose from the vacuum by
turning to the left. Straighten the hose and unclog with a
long, narrow object.
Suction
Opening
7. If the clog persists, follow the instructions for Checking
the Rotating Brush on page 11 and inspect the Air
Passageway for obstructions.
Thermal Protector
Air Passageway
An internal thermal protector has been designed
into your cleaner to protect it from overheating.
When the thermal protector activates, the main
vacuum motor will stop operating. If this
happens, proceed as follows:
1. Turn the cleaner OFF (O) and unplug from
electrical outlet.
2. Check the Upper Tank area, Pre-Motor Filter and
Post-Motor Filter for dirt accumulation.
3. Refer to the "Clearing Clogs" section.
4. When the motor cools for approximately 30
minutes, the thermal protector automatically
resets and cleaning may continue. If the thermal
protector continues to activate after following the
above steps, your cleaner may need servicing.
Note: The thermal protector controls the main
vacuum motor only, not the brush motor. If the
thermal protector activates, the brush will
continue to operate normally; however, there will
be no suction.
ug603-5570_3760E_1105.indd 13
Caution:
To reduce the risk of
injury from moving
parts, turn off vacuum
cleaner and disconnect
Power Plug from
electrical outlet.
13
2/2/06 4:12:20 PM
Troubleshooting
Vacuum cleaner won’t run
Possible Causes
1 Power cord not plugged in
2 Thermal protector activated
WARNING:
To reduce the risk of injury from
moving parts and/or electrical
shock, turn Power Switch OFF and
disconnect plug from electrical
outlet before performing troubleshooting checks.
Remedies
1 Check electrical plug
2 Allow cleaner to cool for 30 minutes,
see pg. 13
No Power at Rotating Floor Brush
Possible Causes
1 Cylinder is not securely seated
Remedies
2 Brush Switch turned to “Off”
1 Remove Cylinder and replace, making
sure that it “clicks” into place
2 Make sure Brush Switch is in “On” position
3 Vacuum is in Upright Position
3 Recline vacuum to operate brush
Vacuum cleaner won’t pick up dirt
Possible Causes
1 Incorrect Height Adjustment
2 Hose not attached to suction opening
3 Crack or hole in Hose
4 Drive Belt broken, worn or off motor pulley
5 Rotating Floor Brush bristles worn
6 Rotating Floor Brush jammed
7 Clog in vacuum
8 Dirt Container full
9 Dirt Container or Upper Tank
not installed properly
10 Filters are dirty
Remedies
1 Adjust Powerfoot to correct height setting
2 Grasp Hose Grip and firmly push onto
the base
3 Check Hose and replace if needed
4 Reposition or replace Drive Belt, see
pg. 11-12
5 Replace Brush
6 Remove Brush and clean debris from
Brush Ends
7 Follow instructions on pg. 13 for
clearing clogs
8 Empty Dirt Container
9 Position correctly and lock in place
10 Check and clean or replace Upper Tank,
Pre-Motor and Post-Motor Filters
Vacuum cleaner is difficult to push
Possible Causes
1 Incorrect Height adjustment
Remedies
1 Adjust Powerfoot to correct height setting
Visible dirt escaping from cleaner
Possible Causes
1 Dirt Container full
2 Filter missing or installed incorrectly
3 Dirt Container installed incorrectly
Remedies
1 Empty Dirt Container
2 Check Upper Tank, Pre-Motor and
Post-Motor Filters for correct installation
3 Pull out and re-insert Dirt Container correctly
14
ug603-5570_3760E_1105.indd 14
2/2/06 4:12:21 PM
BISSELL Consumer Services
If your BISSELL product should require service:
In the UK, Australia, or New Zealand, call BISSELL Consumer Services at the numbers below and we will give you the
location of a BISSELL Authorized Service Center in your area. For all other countries, contact your local in country
distributor for questions, service, or repair.
If you have questions about your warranty or need replacement parts please contact the numbers below.
For Australian inquiries:
E.D. Oates Pty Ltd
Telephone: 1-800-811-183
24 hours a day 7 days a week
For UK inquiries:
BISSELL Homecare (Overseas) Inc.
Telephone: 0870-225-0109
Monday - Thursday 9 am — 5 pm
Friday 9 am — 4 pm
For New Zealand inquiries:
Parex Appliances
Telephone: 0800-247-735
Monday - Friday 8 am — 5 pm
For all other inquiries:
BISSELL Homecare, Inc.
Telephone: 01-616-453-4451
Monday - Friday 8 am — 4 pm
Fax: 01-616-453-1383
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
Note: Please keep your original sales receipt. It provides proof of date of purchase in the event of a
warranty claim. See "About Your Warranty" on page 16 for details.
Please do not return this product to the store.
Replacement Parts – BISSELL Lift-Off Spinpower Series
Item Part No. Part Name
1
2
3
4
5
6
7
8
9
10
11
12
13
3200
203-1063
203-1099
203-6624
203-6830
203-6831
203-1227
203-2082
203-5542
203-2073
203-6778
3093
3091
Style 8 Drive Belt (2-Pack)
Crevice Tool
Dusting Brush/Upholstery Tool
Stair Cleaning Tool (Select Models)
Metal Telescoping Extension Wand
Deluxe Bare Floor Tool - Bali Blue (Select Models)
TurboBrush (Select Models)
Bracket Assembly for TurboBrush (Select Models)
Shoulder Strap (Select Models)
Twist ‘n Snap Hose
Brush Roll
Style 7/8 Upper Tank Filter/Pre-Motor Filter Set
Style 8 HEPA Media Post-Motor Filter
1
2
3
4
5
6
8
9
10
11
12
13
7
15
ug603-5570_3760E_1105.indd 15
2/2/06 4:12:21 PM
Warranty
This warranty gives you specific legal rights, and you may also have other rights which may vary
from country to country. If you need additional instruction regarding this warranty or have questions
regarding what it may cover, please contact BISSELL Consumer Services by telephone, or regular post as
described below, or contact your local in country distributor.
Limited Two Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL Homecare, Inc., will replace (with new
or remanufactured components), at BISSELL’s option, free of charge from the date of purchase by the original
purchaser, for two years any defective or malfunctioning part do to manufacturers defect.
This warranty applies to product used for personal, and not commercial or rental service. This warranty does
not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction
caused by negligence, abuse, or use not in accordance with the User’s Guide is not covered.
For UK inquiries:
Monday - Thursday 9 am — 5 pm
Friday 9 am — 4 pm
BISSELL Homecare (Overseas) Inc.
The Boat Yard
105 Straight Road
Old Windsor
Berkshire, SL4 2SE
United Kingdom
Telephone: 0870-225-0109
For Australian inquiries:
24 hours a day 7 days a week
E.D. Oates Pty Ltd
76 - 82 Newlands Road
Reservoir VIC 3073
Australia
Telephone: 1-800-811-183
For New Zealand inquiries:
Monday - Friday
9 am — 5 pm
Parex Appliances
103 Central Park Drive
Henderson
Auckland
New Zealand
Telephone: 0800-247-735
For all other inquiries:
Monday - Friday
8 am — 4 pm
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, MI 49501 USA
Telephone: 01-616-453-4451
Fax: 01-616-453-1383
BISSELL HOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT.
BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL
OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO THE TWO YEAR DURATION FROM THE DATE
OF PURCHASE AS DESCRIBED ABOVE.
16
ug603-5570_3760E_1105.indd 16
©2005 BISSELL Homecare Inc
Grand Rapids, Michigan
All rights reserved. Printed in Korea
Part Number 603-5570
Rev 11/05
Visit our website at:
www.bissell.com
2/2/06 4:12:23 PM