UXT4036AY Spec Sheet

36"UnderCabinetHood
UXT4036AY
KeyFeatures
• Non-Vented Under Cabinet Hood
(New Design)
• Hidden Vent
• Axial Fan
• Covered, Incandescent Light (75-Watt)
• 2-Speed Rocker Control
• Charcoal Filter Included
Location Requirements
Installation Clearances
IMPORTANT: Observe all governing codes and ordinances.
■ It is the installer’s responsibility to comply with installation
clearances specified on the model/serial rating plate. The
model/serial rating plate is located inside the range hood on
the left wall.
36" Under Cabinet Hood
■
UXT4036AY
Range hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance. Consult the
cooktop/range manufacturer installation instructions before
Requirements
making anyLocation
cutouts.
IMPORTANT: Observe all governing codes and ordinances.
■ Grounded electrical outlet is required. See “Electrical
model no.
■ It
is the installer’s
responsibility
to comply uxt4036ay
with installation
Requirements”
section.
Non-Vented
Only
Type
clearances specified on the model/serial
rating plate.
The
■ model/serial
All openingsgeneral
in ceiling
and
where
range
be on
rating
plate
is wall
located
inside
thehood
rangewill
hood
information
installed
must be sealed.
the
left wall.
C
■
Specifications
Washable Filter
Installation Clearances
Installation
Requirements
B
D
A
Yes
These range
hoods are
factory
forfrom
vented
installations.
Range
hood location
should
be set
away
strong
draft
areas,
Control
2-Speed,
Rocker
Switch
Models
are capable
of being
installed
asvents.
non-vented
such
as that
windows,
doors and
strong
heating
Axial Fan
Blower
(recirculating) require charcoal
filters. See the “Accessories”
■ Cabinet
opening
dimensions
that
are shown
must
be used.
1
Level,
Incandescent
section to
order charcoal
filter
kit.
Lighting
(75-Watt)
Given dimensions provide minimum clearance.
Consult the
installation instructions
Compatibility
Up to 40K BTUbefore
Forcooktop/range
MobileRange/Cooktop
Homemanufacturer
Installations
making Approx.
any cutouts.
Shipping
Weight
The installation of this
range
hood(lbs.)
must conform to14the
Manufactured
Home
Construction
Safety Standards,
Title 24
■
Grounded electrical
outlet
is required.
See “Electrical
optional
accessories
CFR,
Part 328Replacement
(formerly
the
Federal
Standard for
Mobile Home
Requirements”
section.
W10355450
Charcoal
Filter
Construction and Safety, title 24, HUD, Part 280) or when such
■ All openings in ceiling and
wall
where rangeW10355452
hood will be
Power
Cord
standard is not applicable, the standard for Manufactured Home
installed must be
sealed.
Color
Availability
W,B
Installation 1982 (Manufactured Home Sites, Communities and
Setups)
ANSI
A225.1/NFPA
501A*, set
or latest
edition,
withB-Black
local
■
These
range
for vented
installations.
Note:
CFMs
are
based
on
IEChoods
standard are factory
*or
W-White,
Models that are capable of being installed as non-vented
codes.
(recirculating) require charcoal filters. See the “Accessories”
section to
order charcoal filter kit.
Product
Dimensions
■
■
C
B
E
D
A
Dimensions
A. 18" (45.7 cm) min. clearance - upper cabinet to countertop
B. 18" (45.7 cm) to 24" (61.0 cm) suggested max. - bottom of range
hood to cooking surface
C. 30" (76.2 cm) min. cabinet
opening width for 30" (76.2 cm)
E
models and 36" (91.4 cm) min. cabinet width for 36" (91.4 cm)
models.
D. 13" (33.0 cm) cabinet depth
E. 36" (91.4 cm) base cabinet height
For Mobile Home Installations
6⁹⁄₁₆" (16.7
cm) to the
The installation of this range hood must
conform
⁷⁄₈" Home Construction Safety Standards, Title 24
Manufactured
CFR, Part (2.2
328cm)
(formerly the Federal Standard for Mobile Home
Construction and Safety, title 24, HUD, Part 280) or when such
1"
standard
Home
4¹⁵⁄₁₆" is not applicable, the standard for Manufactured
(2.5
cm)
(12.5 cm) 1982 (Manufactured Home Sites, Communities and
Installation
Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local
⁷⁄₈"
codes.
(2.2 cm)
Product Dimensions
29¹⁵⁄₁₆" (76.0 cm) or
35¹⁵⁄₁₆" (91.0 cm)
9"
(22.9 cm)
2¹⁄₈"
(5.4 cm) 18⁵⁄₈"
6⁹⁄₁₆" (16.7 cm) (47.3 cm)
⁷⁄₈"
(2.2 cm)
1"
(2.5 cm)
4¹⁵⁄₁₆"
(12.5 cm)
⁷⁄₈"
(2.2 cm)
29¹⁵⁄₁₆" (76.0 cm) or
35¹⁵⁄₁₆" (91.0 cm)
9"
(22.9 cm)
2¹⁄₈"
(5.4 cm) 18⁵⁄₈"
(47.3 cm)
Venting Requirements
■
Vent system must terminate to the outdoors, except for nonvented
(recirculating)
installations.
A.
18" (45.7
cm) min. clearance
- upper cabinet to countertop
18"
(45.7
cm) to 24"
suggested
bottom
range
■ B.
Do
not
terminate
the(61.0
ventcm)
system
in anmax.
attic- or
otherofenclosed
hood to cooking surface
area.
C. 30" (76.2 cm) min. cabinet opening width for 30" (76.2 cm)
models
anda36"
cabinet width
forcap.
36" (91.4 cm)
■ Do
not use
4" (91.4
(10.2cm)
cm)min.
laundry-type
wall
models.
■ D.
Use
7" (17.8
cm) round
13" a(33.0
cm) cabinet
depthmetal vent or a 3¹⁄₄" x 10" (8.3 x
metalheight
vent, depending on your model.
E.25.4
36" cm)
(91.4rectangular
cm) base cabinet
Rigid metal vent is recommended. Plastic or metal foil vent is
not recommended.
Venting Requirements
Dimensions
are forofplanning
purposes
only.
■ The length
vent system
and
number of elbows should be
For complete
details,
see Installation
Instructions
packed
with product.
kept
to
a
minimum
to
provide
performance.
■ Vent system must terminate toefficient
the outdoors,
except for nonSpecifications subject to change without notice.
vented (recirculating) installations.
■
Do not terminate the vent system in an attic or other enclosed
area.
■
Do not use a 4" (10.2 cm) laundry-type wall cap.
■
Use a 7" (17.8 cm) round metal vent or a 3¹⁄₄" x 10" (8.3 x
25.4 cm) rectangular metal vent, depending on your model.
Rigid metal vent is recommended. Plastic or metal foil vent is
not recommended.
■
The length of vent system and number of elbows should be
kept to a minimum to provide efficient performance.
5
®Registered trademark/™ Trademark of Whirlpool, U.S.A. ©2011. All rights reserved.
AA105059