Mitel 1000 guide Technical information

TECHNICIAN’S HANDBOOK
LIGHTWARE 32, Release 1.0
NOTICE
The information contained in this document is believed to be accurate
in all respects but is not warranted by Mitel Networks Corporation
(MITEL®). The information is subject to change without notice and
should not be construed in any way as a commitment by Mitel or any
of its affiliates or subsidiaries. Mitel and its affiliates and subsidiaries
assume no responsibility for any errors or omissions in this document.
Revisions of this document or new editions of it may be issued to
incorporate such changes.
SX-2000, SUPERSET, and SUPERCONSOLE 1000 are trademarks of
Mitel Networks Corporation.
Other product names mentioned in this document may be trademarks of their
respective companies and are hereby acknowledged.
SX-2000 Technician’s Handbook
50003095, Revision A
LIGHTWARE 32, Release 1.0
January 2003
, Trademark of MITEL Networks Corporation
©Copyright 2003, MITEL Networks Corporation
All rights reserved
Table of Contents
Chapter 1: About This Handbook
About This Handbook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audience. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RSD Drive or Cartridge Tape Unit? . . . . . . . . . . . . . . . . . . . . . . . .
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3
3
3
4
4
4
Chapter 2: Installation
Cabinet Card Layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Redundant Control Cabinet Card Layout . . . . . . . . . . . . . . . . . . . . 9
Non-redundant Control Cabinet Card Layout . . . . . . . . . . . . . . . . 10
MICRO LIGHT Cabinet Card Layout . . . . . . . . . . . . . . . . . . . . . . 11
MICRO LIGHT Cabinet - Valid Card Combinations . . . . . . . . . . . 12
Peripheral Cabinet Card Layout . . . . . . . . . . . . . . . . . . . . . . . . . . 15
DSU Cabinet Card Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Adding a Peripheral or DSU Cabinet . . . . . . . . . . . . . . . . . . . . . . . 17
If the Maximum Number of Cabinets is Selected . . . . . . . . . . . . . 17
If the Maximum Number of Cabinets is Not Selected. . . . . . . . . . 18
Circuit Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Peripheral Interface Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSU Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
20
22
23
Card Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Resource Card Switch Settings . . . . . . . . . . . . . . . . . . . .
E&M Trunk Card Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . .
OPS Line Card Message Waiting Switches . . . . . . . . . . . . . . . . .
DS1 Formatter Card Line Equalizer Switches . . . . . . . . . . . . . . .
CEPT Interface Assembly Jumpers . . . . . . . . . . . . . . . . . . . . . . .
E1/T1 (DS1) Formatter Card Switch Settings. . . . . . . . . . . . . . . .
PRI Cards and DS1/CEPT I and II Cards. . . . . . . . . . . . . . . . . . .
24
24
25
26
27
27
28
28
Peripheral Interface Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USCO Pin Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Card-slot Connections to Cross-connect Field . . . . . . . . . . . . . . .
29
29
29
32
3
Technician’s Handbook
Chapter 3: Programming
Programming Class of Service, Interconnect Restriction,
and Intercept Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Programming Printer Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Printer Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SUPERSET 700 Printer Port . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SUPERCONSOLE 1000® Printer Port . . . . . . . . . . . . . . . . . . . .
SUPERCONSOLE 2000™ Printer Port . . . . . . . . . . . . . . . . . . . .
DATASET Printer Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48
48
48
49
50
51
Programming Peripheral Devices . . . . . . . . . . . . . . . . . . . . . . . . .
Single Line Telephones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Devices Connected to an AIM . . . . . . . . . . . . . . . . . . . . .
Multiline Telephones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programmable Key Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upgrade a PKM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Consoles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
52
52
54
55
56
56
57
Programming the Telephone Directory . . . . . . . . . . . . . . . . . . . . . 59
Changing a Telephone’s Attributes . . . . . . . . . . . . . . . . . . . . . . . . 60
Moving a Telephone User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Swapping Users’ Telephones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Programming Call Rerouting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Programming Trunks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Dial-in Trunk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Non-dial-in Trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DISA Dial-in Trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DISA Non-dial-in Trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital Trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65
65
66
67
68
68
Programming Automatic Route Selection (ARS) . . . . . . . . . . . . . 71
Chapter 4: Maintenance Commands
Basic Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessing Desktop Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logging Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a Different Language . . . . . . . . . . . . . . . . . . . . . . . . . .
Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
77
77
77
77
77
Table of Contents
Changing the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting the Password for a Lower Level . . . . . . . . . . . . . . . . . .
Resetting Usernames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying Usernames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching from CDE or Desktop to Maintenance Mode . . . . . . . .
Stepping Back through Commands . . . . . . . . . . . . . . . . . . . . . . .
Displaying the System Software Revision . . . . . . . . . . . . . . . . . .
Displaying the System Software Versions . . . . . . . . . . . . . . . . . .
Changing or Reading the System Time . . . . . . . . . . . . . . . . . . . .
Changing or Reading the System Date . . . . . . . . . . . . . . . . . . . .
Change Tenant Day/Night Service . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Parity of a Console Port or DNIC Port . . . . . . . . . .
Refreshing the Terminal Screen. . . . . . . . . . . . . . . . . . . . . . . . . .
Cancelling a Maintenance Command. . . . . . . . . . . . . . . . . . . . . .
Printing to LPR3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printing Log Files to a Local Printer . . . . . . . . . . . . . . . . . . . . . . .
Printing a CDE Form. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching the Terminal from Screen Mode to Print Mode . . . . . .
Checking the Print Queue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cancelling a Print Job. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assigning a New Default Printer. . . . . . . . . . . . . . . . . . . . . . . . . .
Creating a Catalog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying Catalogs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
78
78
78
78
78
79
79
79
79
79
80
80
80
80
81
81
81
81
83
83
83
84
84
84
Troubleshooting Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting, Ending, and Printing a Session Log . . . . . . . . . . . . . . . .
Showing Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Showing Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Alarm Thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying the State of a Circuit . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying the State of Line Appearances . . . . . . . . . . . . . . . . . .
Displaying the Total Number of System Resources . . . . . . . . . . .
Busying Out a Card, Circuit, or Channel for Testing . . . . . . . . . .
Returning a Busy Circuit or Trunk to Service . . . . . . . . . . . . . . . .
Removing a Courtesy Down Request . . . . . . . . . . . . . . . . . . . . .
Testing Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying the Call Path of a Set . . . . . . . . . . . . . . . . . . . . . . . . .
Reading Maintenance Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cancelling a Logs Read Command . . . . . . . . . . . . . . . . . . . . . . .
Printing Maintenance Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
85
85
85
85
86
86
86
86
87
87
87
88
89
89
90
90
5
Technician’s Handbook
Deleting Log Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Checking the Log Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Setting the Size of the SMDR Log File. . . . . . . . . . . . . . . . . . . . . 90
Main Control Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching Activity (Redundant Systems Only) . . . . . . . . . . . . . . .
Scheduling an Activity Switch (Redundant Systems Only) . . . . .
Turning Background Diagnostics On/Off . . . . . . . . . . . . . . . . . . .
Displaying the Card Configuration . . . . . . . . . . . . . . . . . . . . . . . .
Identifying System Resource Shortages . . . . . . . . . . . . . . . . . . .
Identifying and Downloading Firmware . . . . . . . . . . . . . . . . . . . .
Identifying Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking for Mass Storage Subsystem Errors . . . . . . . . . . . . . .
Loading Software into a Card’s Processor. . . . . . . . . . . . . . . . . .
Testing PCM Links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scheduling a System Reboot (Non-redundant Systems). . . . . . .
Displaying the Status of Communication Paths . . . . . . . . . . . . . .
Collecting Traffic Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying Traffic Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
91
91
91
92
92
92
92
94
94
94
95
95
96
96
97
Database Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Checking the Database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Saving and Restoring the Database . . . . . . . . . . . . . . . . . . . . . . 99
RSD Copy from Mitel Support Web Site . . . . . . . . . . . . . . . . . . 100
Backing Up and Restoring Message Center Messages. . . . . . . 100
Redundant File System Commands . . . . . . . . . . . . . . . . . . . . . .
Partitioning and Joining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disabling and Enabling File Redundancy . . . . . . . . . . . . . . . . .
Which Main Controller is Active? . . . . . . . . . . . . . . . . . . . . . . . .
Displaying Information on a Volume . . . . . . . . . . . . . . . . . . . . .
Mounting and Dismounting a Volume . . . . . . . . . . . . . . . . . . . .
Backing Up and Restoring a Volume . . . . . . . . . . . . . . . . . . . . .
Enabling and Disabling Access to a Volume . . . . . . . . . . . . . . .
Formatting a Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
101
101
101
102
102
102
102
103
104
Peripheral Devices Commands . . . . . . . . . . . . . . . . . . . . . . . . . .
Locating an Extension or Trunk . . . . . . . . . . . . . . . . . . . . . . . . .
Locating Where a Number is Used . . . . . . . . . . . . . . . . . . . . . .
Locating a Tenant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Listing the Active Features for an Extension or PLID. . . . . . . . .
Finding the Directory Number of a Set or Trunk . . . . . . . . . . . .
Finding Free Directory Numbers or PLIDs . . . . . . . . . . . . . . . . .
105
105
105
105
105
106
106
6
Table of Contents
Moving, Adding, and Swapping Telephone Users . . . . . . . . . . . 107
Deleting Telephone Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Changing an Extension Number. . . . . . . . . . . . . . . . . . . . . . . . . 107
Digital Trunk Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying the Status of a Digital Link . . . . . . . . . . . . . . . . . . . .
Testing Digital Trunks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Synchronizing the Active Clock Source . . . . . . . . . . . . . . . . . . .
Displaying Synchronization Information . . . . . . . . . . . . . . . . . . .
108
108
108
109
109
DS1/CEPT Formatter I Card (MC263CA and MC264CA)
Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Chapter 5: Troubleshooting and Repair
Identifying Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Bootstrap Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flowchart 1: Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flowchart 2: The System is Not Booting Up. . . . . . . . . . . . . . . .
Flowchart 3: An Alarm is Present . . . . . . . . . . . . . . . . . . . . . . . .
Flowchart 4: Correcting Set/Dataset Problems . . . . . . . . . . . . .
Flowchart 5: The Bootstrap Sequence . . . . . . . . . . . . . . . . . . . .
Flowchart 6: Maintenance Terminal Troubleshooting. . . . . . . . .
115
115
116
118
120
121
123
127
Fixing Database Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Restoring the Database from a DATA SAVE Backup . . . . . . . . 128
If the System Reports a Blank Database . . . . . . . . . . . . . . . . . . 132
If the System Reports that the System Dimensions Don’t Match 132
If the System Reports a SYSID Mismatch . . . . . . . . . . . . . . . . . 132
Fixing Redundant File Corruption . . . . . . . . . . . . . . . . . . . . . . . . 133
Power-down Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Powering Down the Control Node . . . . . . . . . . . . . . . . . . . . . . .
Powering Down the Peripheral Nodes . . . . . . . . . . . . . . . . . . . .
Powering Down the DSU Nodes . . . . . . . . . . . . . . . . . . . . . . . .
136
136
137
137
Power-up Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Powering Up the Control Node. . . . . . . . . . . . . . . . . . . . . . . . . .
Powering Up the Peripheral Nodes . . . . . . . . . . . . . . . . . . . . . .
Powering Up the DSU Nodes . . . . . . . . . . . . . . . . . . . . . . . . . . .
138
138
138
139
7
Technician’s Handbook
Recovering from a Corrupted Hard Disk. . . . . . . . . . . . . . . . . . . 140
Formatting the Hard Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Removing and Replacing a Faulty Hard Disk . . . . . . . . . . . . . . 143
Replacing Circuit Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing a Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing a Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing a Main Controller Card . . . . . . . . . . . . . . . . . . . . . . .
Replacing a Peripheral Switch Controller (PSC) Card . . . . . . . .
Replacing a Control Resource Card (CRC) . . . . . . . . . . . . . . . .
Replacing CEPT or DS1 Formatter Cards
with DS1/CEPT I or II Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . .
146
146
146
147
148
149
150
Chapter 6: Routine Maintenance
Is the System Healthy? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Non-redundant Healthy System Checklist . . . . . . . . . . . . . . . . . 155
Redundant Healthy System Checklist . . . . . . . . . . . . . . . . . . . . 155
Is the System Secure? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Checking a Non-redundant System. . . . . . . . . . . . . . . . . . . . . . . 157
Checking a Redundant System . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Making Your System Secure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
RSD Copier Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Formatting a Removable Storage Device (RSD) . . . . . . . . . . . . 163
Making a DATA SAVE Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Making a Message Center Backup . . . . . . . . . . . . . . . . . . . . . . . 165
Making an RSD Copy of the Hard Disk . . . . . . . . . . . . . . . . . . . . 166
Loading Software on Your System . . . . . . . . . . . . . . . . . . . . . . .
Software Upgrade or Software Update? . . . . . . . . . . . . . . . . . .
Data Restore or Data Convert? . . . . . . . . . . . . . . . . . . . . . . . . .
RSD or Tape? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Performing a Software Upgrade
on a Non-redundant System . . . . . . . . . . . . . . . . . . . . . . . . . . .
Performing a Software Update on a Non-redundant System. . .
Performing a Software Upgrade on a Redundant System . . . . .
Performing a Software Update on a Redundant System . . . . . .
8
168
168
168
168
169
170
178
179
190
Table of Contents
Performing an Option Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . .
Options and MFRDs are Password Protected . . . . . . . . . . . . . .
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enabling Options and MFRDs on Non-redundant Systems . . . .
Enabling Options and MFRDs on Redundant Systems . . . . . . .
194
194
194
194
197
Index of Maintenance Commands . . . . . . . . . . . . . . . . . . . . . . . . 203
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
E-Doc Tips
9
Technician’s Handbook
10
Chapter 1
About This Handbook
Technician’s Handbook
2
About This
Handbook
About This Handbook
Purpose
This handbook provides:
!
quick reference to maintenance commands
!
abbreviated instructions for frequently used procedures
!
programming aids
!
troubleshooting flowcharts
!
installation information.
Audience
This handbook is for certified technicians.
Symbols
A stop symbol indicates a hazardous situation which, if not
avoided, could result in injury or death.
A yield symbol with an exclamation mark indicates a
situation which, if not avoided, could result in damage to the
equipment.
A light bulb identifies an important note or a useful tip.
5 min
A clock indicates the amount of time that is required to
perform the associated step.
A pointer symbol identifies an important cross reference.
A hand identifies a step where you must make an important
command selection.
3
Technician’s Handbook
Important Safety Instructions
Failure to follow all instructions may result in improper
equipment operation and/or risk of electrical shock.
See the SX-2000® Safety Instructions, included with every
system, for general safety information.
RSD Drive or Cartridge Tape Unit?
This handbook describes how to perform software
procedures on a system that has an RSD drive. If your
system has a cartridge tape unit, substitute TAPE for RSD
when you enter maintenance commands.
Additional Information
Technical Documentation CD-ROM
The Technical Documentation CD-ROM provides complete
information about the SX-2000 system. The documentation
has been enhanced with animated FRU procedures and a
Troubleshooting Tool.
Mitel Online
Mitel Online provides free access to the latest technical
documentation updates, Technical Service Bulletins (TSBs),
compatibility considerations, and recognized support
issues. You can also participate in Tech-to-Tech forums.
Training course schedules are provided, and you can
update your training certification online.
1. Launch your browser and access www.mitel.com.
2. From the OnLine Services menu, select Mitel Online.
3. Enter your login name and password.
4. Click Technical Support Highlights and then click
Product Documentation (eDocs).
4
Field Change Instruction
You can obtain the latest FCI from Mitel Online.
Technical Service Bulletins
Technical Service Bulletins (TSBs) are issued by Mitel
Technical Support to address frequently asked questions
regarding software and hardware problems.
You can obtain the latest TSBs from Mitel Online.
Known Bug List
Known bugs are tracked by Mitel Technical Support. Consult
the Known Bug List if you see a problem on your system.
The list offers work-arounds that may save you a Technical
Support call.
You can obtain the latest Known Bug List from Mitel Online.
5
About This
Handbook
Every software release is accompanied by a Field Change
Instruction (FCI). The FCI describes software changes, bug
fixes, outstanding issues, and hardware compatibility
considerations for the new software release. Read the FCI
before you begin any software upgrade.
Technician’s Handbook
6
Chapter 2
Installation
7
Technician’s Handbook
8
Installation
Cabinet Card Layouts
Redundant Control Cabinet Card Layout
Installation
Figure 1: Redundant Control Cabinet Card Layout
9
Technician’s Handbook
Non-redundant Control Cabinet Card Layout
HARD DISK DRIVE
RSD DRIVE
MAIN CONTROLLER CARD
CONTROL RESOURCE CARD
CONTROL PANEL
1
2
BB0409
Figure 2: Non-redundant Control Cabinet Card Layout
10
Installation
MICRO LIGHT Cabinet Card Layout
Installation
Figure 3: MICRO LIGHT Cabinet Card Layout
11
Technician’s Handbook
MICRO LIGHT Cabinet - Valid Card Combinations
Figure 4: MICRO LIGHT - Valid Card Combinations
12
Installation
Table 1: Completing the MICRO LIGHT Cabinet Assignment Form
CONFIGURATION 1 - CABINET ASSIGNMENT
Main Control Fiber Interface
Peripheral/DSU Fiber Interface
Cabinet
Shelf
Slot
Type
Cabinet
Shelf
Slot
Comments
1
2
1
FD Per
2
1
17
internal peripheral
2
2
2
3
2
4
1
2
1
FD Per
2
1
17
internal peripheral
B 1
& 1
C 1
2
2
FD DSU 3
1
1
internal DSU
2
3
2
4
Installation
1
A 1
1
1
2
1
FD Per
2
1
17
internal peripheral
D 1
& 1
E 1
2
2
FD DSU 3
1
1
internal DSU
2
3
2
4
FD DSU 3
1
6
internal DSU
1
2
1
FD Per
2
1
17
internal peripheral
1
2
2
1
2
3
FD Per
4
1
17
external peripheral Note
1
2
4
internal peripheral
F
1
2
1
FD Per
2
1
17
G 1
& 1
H 1
2
2
FD DSU 3
1
1
internal DSU
2
3
FD Per
4
1
17
external peripheral Note
2
4
1
2
1
FD Per
2
1
17
internal peripheral
1
2
2
FD DSU 3
1
1
internal DSU
1
2
3
FD Per
4
1
17
external peripheral Note
1
2
4
FD DSU 3
1
6
internal DSU
1
2
1
FD Per
2
1
17
internal peripheral
1
2
2
1
2
3
FD Per
4
1
17
external peripheral Note
1
2
4
FD Per
5
1
17
external peripheral Note
I
J
13
Technician’s Handbook
Table 1: Completing the MICRO LIGHT Cabinet Assignment Form (Cont’d)
CONFIGURATION 1 - CABINET ASSIGNMENT
Main Control Fiber Interface
Peripheral/DSU Fiber Interface
Cabinet
Shelf
Slot
Type
Cabinet
Shelf
Slot
Comments
1
2
1
FD Per
2
1
17
internal peripheral
K 1
& 1
L 1
2
2
FD DSU 3
1
1
internal DSU
2
3
FD Per
4
1
17
external peripheral Note
2
4
FD Per
5
1
17
external peripheral Note
1
2
1
FD Per
2
1
17
internal peripheral
1
2
2
FD Per
3
1
17
external peripheral Note
M 1
1
2
3
FD Per
4
1
17
external peripheral Note
2
4
FD Per
5
1
17
external peripheral Note
1
2
1
FD Per
2
1
17
external peripheral Note
1
2
2
FD DSU 3
1
1
internal DSU
N 1
1
2
3
FD Per
4
1
17
external peripheral Note
2
4
FD Per
5
1
17
external peripheral Note
1
2
1
FD Per
2
1
17
external peripheral Note
1
2
2
FD Per
3
1
17
external peripheral Note
O 1
1
2
3
FD Per
4
1
17
external peripheral Note
2
4
FD Per
5
1
17
external peripheral Note
Note: You can also connect the FIM in this slot to a FIM in a DSU cabinet. If you are
connecting a DSU cabinet, enter the following data:
Type: Enter “FD DSU”.
Slot: Enter “1” if it is connected to a FIM in slot 1 of a DSU cabinet. Enter
“6” if it is connected to a FIM in slot 6 of a DSU cabinet.
Comments: Enter the location of the external DSU cabinet. This field accepts
up to 14 alpha numeric characters.
14
Installation
Peripheral Cabinet Card Layout
Installation
Figure 5: Peripheral Cabinet Card Layout
Note: Depending on the peripheral cabinet type, slots 16, 16B, and 17 may be used
for different card configurations:
Type A - (9400-200-110-NA) - holds a PSC in slot 16, a PRC in the upper portion of slot 17, and a FIM in the lower portion of slot 17.
Type B - (9400-200-113-NA) - holds a PSC or PSC II in slot 16. A PSC works
with a PRC in the upper portion of slot 17; a PSC II does not require a separate
PRC. A FIM is held in the lower portion of slot 17. If used in an expanded
peripheral node, it must be used as the slave cabinet and includes a Peripheral
Interconnect card in slot 16.
Peripheral Cabinet II - (9400-200-118-NA) - holds a PSC II in slot 16, a FIM in
slot 17, and if used in an expanded peripheral node as the master cabinet a
Peripheral Interconnect card in slot 16B. If used as the slave cabinet, a Peripheral Interconnect card is installed in slot 16 (no PSC or FIM required).
15
16
FIBER INTERFACE MODULE
DIGITAL SERVICE UNIT
DIGITAL SERVICE UNIT
DIGITAL SERVICE UNIT
DIGITAL SERVICE UNIT
FIBER INTERFACE MODULE
PERIPHERAL RESOURCE CARD
PERIPHERAL RESOURCE CARD
Technician’s Handbook
DSU Cabinet Card Layout
1
2
3
4
5
6
BB0410
Figure 6: DSU Cabinet Card Layout
Installation
Adding a Peripheral or DSU Cabinet
Service will be lost during this procedure.
1. If your system is redundant, hold down PANEL ENABLE
and press ACTIVITY FREEZE ON.
3. Connect the fiber cable to the FIM in the control node.
4. Power up the cabinet.
5. Enter CDE mode on the maintenance terminal.
6. Select the Dimension and Feature Display form, and
ensure the maximum number of cabinets is selected for
your system configuration. For FD1 configurations
(non-redundant and SX-2000 MICRO LIGHT systems)
the number of cabinets should be set to 5. For FD2
configurations (redundant systems and 18”
non-redundant cabinets) the number of cabinets should
be set to 12.
7. If the maximum number of cabinets is selected, continue.
If the maximum number of cabinets is not selected,
proceed to page 18.
If the Maximum Number of Cabinets is Selected
1. Enter the Cabinet Assignment form.
2. For non-redundant and redundant LIGHT systems,
complete the Cabinet Assignment form as follows:
Type: Enter “FD Per” or “FD DSU”.
Cabinet: Assign cabinets with numbers 2 through 12.
Shelf: Enter 1.
Slot: Enter 17 for a peripheral cabinet. Enter 1 for DSU
cabinets with DSU cards in slots 2 or 3. Enter 6 for DSU
cabinets with DSU cards in slots 4 or 5.
17
Installation
2. Install the peripheral or DSU cabinet.
Technician’s Handbook
Comments: Enter the location of the new cabinet.
For MICRO LIGHT systems, refer to Figure 4 (page 12)
to determine the letter designation for your card
configuration. From Table 1 (page 13), locate the cabinet
assignment form that has the same letter designation as
your card configuration. Enter the table data into the
Cabinet Assignment form.
The following step takes the system out of service.
3. Commit the form. The system goes out of service.
4. After service is restored, enter the System Configuration
form and program the peripheral interface cards into the
new cabinet.
5. If your system is redundant, hold down PANEL ENABLE
and press ACTIVITY FREEZE OFF.
If the Maximum Number of Cabinets is Not Selected
Non-redundant Systems
1. Save the database to RSD (see page 164).
2. Ensure that you have removed the RSD from the RSD
drive.
3. Enable the options (see page 194).
Enter 5 for the maximum number of cabinets in the
Dimension and Feature Select form. Note that a new
password is not required.
4. Complete the Cabinet Assignment form.
For MICRO LIGHT systems, refer to Figure 4 (page 12)
to determine the letter designation for your card
configuration. From Table 1 (page 13), locate the cabinet
assignment form that has the same letter designation as
your card configuration. Enter the table data into the
Cabinet Assignment form.
18
Installation
5. Restore the database (see page 174).
After service is restored, enter the System Configuration
form and program the Peripheral Interface cards into the
new cabinet.
Redundant Systems
Installation
1. Save the database to RSD (see page 164).
2. Remove the RSD from the RSD drive.
3. Set ACTIVITY FREEZE to ON.
4. Enter PARTITION first from the active plane, then from
the inactive plane.
5. Enable options on the inactive plane (see page 197).
Enter 12 for the maximum number of cabinets in the
Dimension and Feature Select form.
6. Complete the Cabinet Assignment form.
7. Restore the database from RSD to the inactive plane
(see page 183).
The following step will interrupt service.
8. Press and hold the PANEL ENABLE button and press
the ACTIVITY SWITCH button.
9. Copy the software to the newly inactive plane and JOIN
the system (see page 193).
10. After service is restored, enter the System Configuration
form and program the Peripheral Interface cards into the
new cabinet.
11. Hold down PANEL ENABLE and press ACTIVITY
FREEZE OFF.
19
Technician’s Handbook
Circuit Cards
Peripheral Interface Cards
Table 2:
Card
Peripheral Interface Cards
Devices Supported
Circuits
Maximum Loop
Resistance/LoopLengths
AC15 Trunk
Card
AC15 trunk
8
not applicable
COV Line
Card
SUPERSET™ 3 and
SUPERSET 4 telephones
12
Loop resistance: 280 ohms
Loop length:
26 AWG (27 IWG) - 1000 m
(3300 ft.)
24 AWG (25 IWG) - 1500 m
(5000 ft.)
22 AWG (22 IWG) - 2000m
(6000 ft.)
DID/Loop Tie
Trunk Card,
DID/2 Card
Direct Inward Dial (DID)
trunks from CO
4
Loop resistance: 2450 ohms
Loop length:
26 AWG (27 IWG) - 7986 m
(25955 ft.)
22 AWG (22 IWG) - 19995 m
(64984 ft.)
DNI Line
card
SUPERSET digital
telephones
Datasets
Attendant Consoles
Programmable Key
Modules
DNIC MOH/Paging Unit
16
Loop length:
24 AWG (25 IWG) - 1000 m
(3300 ft.) including up to 50 m
(162.5 ft.) 22 AWG (22 IWG)
quad wire and up to 3 m modular
line cord without bridge taps.
DTMF
Receiver
Card
DTMF telephone keypads
and end-to-end signaling
equipment.
16
not applicable
E&M Trunk
Card
E&M tie trunk
Music on hold equipment
Loudspeaker equipment
Paging equipment
4
not applicable
(Sheet 1 of 2)
20
Installation
Table 2:
Card
Fiber
Interface
Module
Peripheral Interface Cards (Cont’d)
Devices Supported
Interfaces control node
with DSU and peripheral
nodes.
Circuits
1
Maximum Loop
Resistance/LoopLengths
Maximum Length:
Approximately 1 km (0 to 5 km
based on the sum of the cable
loss and connector and/or splice
losses. Total loss cannot exceed
6 dB.).
LS/GS trunk
card
Ground start CO trunks
Loop start CO trunks
8
not applicable
ONS and
ONS
CLASS/CLIP
Line Card
DTMF (2500) telephones
Rotary (500) telephones
Night bells
16
External loop resistance:
600 ohms
External wire resistance:
400 ohms
External loop length:
22 AWG (23 IWG) - 3800 m
(12350 ft.)
26 AWG (27 IWG) - 1500 m
(4875 ft.)
OPS Line
Card
DTMF (2500) telephones
Rotary (500) telephones
8
External loop resistance:
1800 ohms
External wire resistance:
1600 ohms
External loop length:
22 AWG (22 IWG) - 15240 m
(50000 ft.)
26 AWG (27 IWG) - 5853 m
(19200 ft.)
(Sheet 2 of 2)
21
Installation
Maximum Permitted Loss in
Fiber:
6 dB, using 62.5/125 µm optical
cable with a numerical aperture
of 0.275 inches.
Technician’s Handbook
DSU Cards
Table 3:
DSU Cards
Card
Devices Supported
# of Channels/Links
BRI Card
ISDN Basic Rate Interface card
6 or 15 BRI Circuits
CEPT Formatter Card
(all variants)
CEPT digital trunk
60 channels
(two 30-channel links and
2 D-channels)
Conference Card
Flexible assignment for up to 64
conference channels; up to eight
conferees per conference call; up to 21
three-party conferences.
64 conference channels
DS1 Formatter Card
(all variants)
T1/D4 digital trunk
2 x 24-channel links
PRI E1 Card
ISDN Primary Rate Interface card
2 x 30 B-channel and 2
D-channel links
PRI T1 Card
ISDN Primary Rate Interface card
2 x 23 B-channel and 1
D-channel link
R2 Card
Protocol Converter - converts incoming
MF-R2 signals from the PSTN to
DPNSS, and outgoing DPNSS to
MF-R2 signals for the PSTN.
two E1 links
(2 x 30-channel links )
Tone Detector Card
Tone level detection
Auto-correlation tone detection
Threshold crossing count tone
detection
Cadence tone detection
32 tone detection channels
22
Installation
Control Cards
Table 4:
Control Cards
Card
Important Details
Provides 8 Mbytes of RAM if system is running software version
M21.0 or earlier. If the system is running software version M21.1 or
later, it provides 15 Mbytes of RAM, and therefore the control RAM
II cards must be removed.
Main Controller III or
Main Controller III R
Provides 16 Mbytes of RAM.
Main Controller III E
Provides 16 Mbytes of RAM if system is running a software version
between P02.3.2 and Q10.7.14 (must be programmed as MCIIIr).
If the system is running software version Q10.5 or later, it provides
32 Mbytes of RAM and built-in Ethernet connection.
Circuit Switch Matrix II
Increases main controller’s circuit switch size from 24 x 24 circuit
switch links to a 48 x 48 non-blocking link matrix. It is required in a
redundant system.
Control Resource Card
Required in SX-2000 LIGHT non-redundant and redundant
systems.
Control Resource Card II
This card is required in the SX-2000 MICRO LIGHT system but
can be used as a replacement for the control resource card in
SX-2000 LIGHT non-redundant and redundant systems.
Control Resource Card III
This card is required for systems that use the OPS Manager ETI
interface.
Peripheral Switch
Controller Card
This card performs all peripheral switch functions for up to 12
Peripheral Interface Cards.
Peripheral Resource Card
Peripheral nodes that use a PSCII have PRC functionality built in.
One or two peripheral resource cards are installed in each DSU
node.
23
Installation
Main Controller II E
Technician’s Handbook
Card Settings
Control Resource Card Switch Settings
These switches determine which maintenance terminal
ports are active.
Table 5: Control Resource Card Switch Settings
Maintenance Data Output
Switch settings
S1
S2
S3
S4
Control (or SX-2000 MICRO LIGHT),
peripheral, and DSU nodes (default)
closed
closed
not used
not used
Control (or SX-2000 MICRO LIGHT) node only
open
open
not used
not used
Peripheral and DSU nodes only
open
closed
not used
not used
Control (or SX-2000 MICRO LIGHT) node only
closed
open
not used
not used
Figure 7: Control Resource Card
24
Installation
E&M Trunk Card Switch Settings
Set switch SN-1 and SN-2 on the E&M trunk cards.
Table 6:
E&M Trunk Switch Settings
Types of Interface Circuits
Signal/Carrier Set Types
Switch Positions
Co-located Trunk Types
SN-1∗
SN-2∗
NONE
A
B
TYPE II
TYPE II
B
A
TYPE IV
TYPE IV
B
A
TYPE V
TYPE I
B
B
TYPE V
TYPE III
B
B
TYPE V
TYPE V
B
B
Installation
TYPE I
∗Positions are SN-1 and SN-2 where N is the particular trunk circuit number on the card (1 through 4).
Figure 8: E&M Trunk Card
25
Technician’s Handbook
OPS Line Card Message Waiting Switches
Set message waiting switches for each circuit (S1 through
S8) as follows:
Table 7: OPS Line Card Switch Settings
Setting
Description
A
Circuits are connected to Off-Premises (OPS) lines. Loop extended over the
Message-Waiting Answer (MWA)/Message-Waiting Busy (MWB) pair to the
called extension.
B
Circuits are connected to On-Premises (ONS) lines. Consists of a -140 Vdc
source delivered at a variable rate to the Ring lead of the called extension.
Rate is custom programmed during CDE to be continuously on through 80
Hz.
Figure 9: OPS Line Card
26
Installation
DS1 Formatter Card Line Equalizer Switches
Set the line equalizer switches S1 and S2 as follows:
Table 8: Line Equalizer Settings
Line Length
Switch Cells
(meters)
1
2
3
4
5
6
7
0 - 150
0 - 45.8
close
open
open
open
open
open
open
150 - 450
45.8 - 137.4
open
close
open
open
close
open
close
450 - 750
137.4 - 229
open
open
close
close
open
close
open
Note: The DS1 interface meets the AT&T DSX-1 specification for distances up to 655
feet (200 m) if 22 AWG (22 IWG) shielded cable is used. The interface can
operate at up to 750 feet (229 m), but compliance with the AT&T DSX-1 specification is not guaranteed at this distance. For greater distances, a repeater must
be used.
CEPT Interface Assembly Jumpers
Jumper positions J06 to J09 allow you to ground the shields
of the coaxial cable connectors. Jumper positions J10 to J13
provide locations to affix the jumpers when they are not in
grounding positions. Jumpers J06, J07, J09, J011, and J12
are located beneath the side of the CEPT interface
assembly faceplate.
Table 9: CEPT Interface Assembly Connector Shield Grounding
Circuit 0
Circuit 1
RX grounded
jumper across J06
RX grounded
jumper across J08
RX not grounded
no jumper across J06
RX not grounded
no jumper across J08
TX grounded
jumper across J07
TX grounded
jumper across J09
TX not grounded
no jumper across J07
TX not grounded
no jumper across J09
Note: Default settings are shown in bold.
27
Installation
(feet)
Technician’s Handbook
E1/T1 (DS1) Formatter Card Switch Settings
Set E1/T1 mode using the E1/T1 switches on the card’s side
Table 10: E1/T1 (DS1) Formatter Card Switch Settings
E1/T1 Switches
Mode
Channel
24
Switch 1
(Link 1)
Switch 2
(Link 2)
E1 mode (compatible for connection
to MSDN DS1 trunks that have been
externally converted from MSDN
CEPT trunks)
data not
inverted
open
open
T1 mode (normal DS1 formatter card
operation)
data
inverted
closed
closed
Note: If you set a link for E1 mode, the data on channel 24 is not inverted. The
external carrier must map the channels to the CEPT link.
PRI Cards and DS1/CEPT I and II Cards
To set the card for LT, remove the NT jumper blocks and
place them on the LT jumpers.
Figure 10: Dual E1 PRI Card
28
Installation
Peripheral Interface Cabling
Cable Connectors
Use AMP Champ or equivalent cable connectors
!
50-pin RS (receptacle - screw lock)
!
female
!
screw lock
!
90 tapered slide-on hood.
USCO Pin Designations
The USCO connector numbers are
!
RJ21X for CO trunks
!
RJ2EX for 2-wire E&M trunks
!
RJ2FX for 4-wire E&M trunks
!
RJ2GX for 4-wire E&M trunks
!
RJ2HX for 4-wire E&M trunks.
29
Installation
Use the tables in this section to cable the peripheral node
card connectors to the Main Distribution Frame (MDF).
When cabling the SX-2000 MICRO LIGHT node connectors,
use the cabling tables that correspond to the peripheral
interface card slot in the MICRO LIGHT node.
Technician’s Handbook
Table 11: USCO Connector Pin Designations
Pin
Color
Code
RJ2IX
RJ2EX
RJ2GX
RJ2FX
RJ2HX
26
W/BL
T
T
T
T
T
1
BL/W
R
R
R
R
R
27
W/O
T
E
T1
E
T1
2
O/W
R
M
R1
SG
R1
28
W/G
T
T
E
M
E
3
G/W
R
R
M
SB
SG
29
W/BR
T
E
T
T
M
4
BR/W
R
M
R
R
SB
30
W/S
T
T
T1
E
T
5
S/W
R
R
R1
SG
R
31
R/BL
T
E
E
M
T1
6
BL/R
R
M
M
SB
R1
32
R/O
T
T
T
T
E
7
O/R
R
R
R
R
SG
33
R/G
T
E
T1
E
M
8
G/R
R
M
R1
SG
SB
34
R/BR
T
T
E
M
T
9
BR/R
R
R
M
SB
R
35
R/S
T
E
T
T
T1
10
S/R
R
M
R
R
R1
36
BK/BL
T
T
T1
E
E
11
BL/BK
R
R
R1
SG
SG
37
BK/O
T
E
E
M
M
12
O/BK
R
M
M
SB
SB
38
BK/G
T
T
T
T
T
13
G/BK
R
R
R
R
R
39
BK/BR
T
E
T1
E
T1
14
BR/BK
R
M
R1
SG
R1
(Sheet 1 of 2)
30
Installation
Table 11: USCO Connector Pin Designations (Cont’d)
Pin
Color
Code
RJ2IX
RJ2EX
RJ2GX
RJ2FX
RJ2HX
BK/S
T
T
E
M
E
15
S/BK
R
R
M
SB
SG
41
Y/BL
T
E
T
T
M
16
BL/Y
R
M
R
R
SB
42
Y/O
T
T
T1
E
T
17
O/Y
R
R
R1
SG
R
43
Y/G
T
E
E
M
T1
18
G/Y
R
M
M
SB
R1
44
Y/BR
T
T
T
T
E
19
BR/Y
R
R
R
R
SG
45
Y/S
T
E
T1
E
M
20
S/Y
R
M
R1
SG
SB
46
V/BL
T
T
E
M
T
21
BL/V
R
R
M
SB
R
47
V/O
T
E
T
T
T1
22
O/V
R
M
R
R
R1
48
V/G
T
T
T1
E
E
23
G/V
R
R
R1
SG
SG
49
V/BR
T
E
E
M
M
24
BR/V
R
M
M
SB
SB
50
V/S
--
--
SPARE
--
--
25
S/V
--
--
SPARE
--
--
Installation
40
(Sheet 2 of 2)
31
Technician’s Handbook
Card-slot Connections to Cross-connect Field
Table 12 (page 33) through Table 23 (page 44) show the
pin-out signals of the interface cards as they appear on J1
through J8. The following abbreviations are used in the
tables:
32
ONS L C
ONS line card & ONS CLASS/CLIP line card
OPS L C
OPS line card
LS/GS Trunk
Loop Start/Ground Start Trunk card
E&M Trunk
E&M trunk card
DID/LT Trunk
Direct Inward Dialing/Loop Tie Trunk card
DID/2
Direct Inward Dialing
COV L C
SUPERSET 3 and SUPERSET 4 line card
DNI L C
Digital Network Interface line card
Installation
Table 12: Card Slot 1 Connections to Cross-connect Field
Color
Code
ONS
LC
OPS
LC
LS/GS
Trunk
26
1
27
2
28
3
29
4
30
5
31
6
32
7
33
8
W/BL
BL/W
W/O
O/W
W/G
G/W
W/BR
BR/W
W/S
S/W
R/BL
BL/R
R/O
O/R
R/G
G/R
26
1
27
2
28
3
29
4
30
5
31
6
32
7
33
8
W/BL
BL/W
W/O
O/W
W/G
G/W
W/BR
BR/W
W/S
S/W
R/BL
BL/R
R/O
O/R
R/G
G/R
E&M
Trunk
DID/LT
Trunk
DID/2
Trunk
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
1T
1R
1MWB
1MWA
2T
2R
2MWB
2MWA
3T
3R
3MWB
3MWA
4T
4R
4MWB
4MWA
1T
1R
1T(MR)
1R(MR)
2T
2R
2T(MR)
2R(MR)
3T
3R
3T(MR)
3R(MR)
4T
4R
4T(MR)
4R(MR)
1T
1R
1T1
1R1
1E
1SG
1M
1SB
2T
2R
2T1
2R1
2E
2SG
2M
2SB
1T
1R
1T
1R
2T
2R
2T
2R
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
5T
5R
5MWB
5MWA
6T
6R
6MWB
6MWA
7T
7R
7MWB
7MWA
8T
8R
8MWB
8MWA
5T
5R
5T(MR)
5R(MR)
6T
6R
6T(MR)
6R(MR)
7T
7R
7T(MR)
7R(MR)
8T
8R
8T(MR)
8R(MR)
3T
3R
3T1
3R1
3E
3SG
3M
3SB
4T
4R
4T1
4R1
4E
4SG
4M
4SB
3T
3R
5T
5R
4T
4R
6T
6R
3T
3R
COV
LC
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
7T
7R
8T
8R
9T
9R
10T
10R
11T
11R
12T
12R
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
4T
4R
7T
7R
8T
8R
DNI
LC
Peripheral
Backplane
Plugs
Installation
Pin
P1
P2
33
Technician’s Handbook
Table 13: Card Slot 2 Connections to Cross-connect Field
Pin
Color
Code
ONS
LC
OPS
LC
LS/GS
Trunk
E&M
Trunk
DID/LT
Trunk
DID/2
Trunk
34
9
35
10
36
11
37
12
38
13
39
14
40
15
41
16
R/BR
BR/R
R/S
S/R
BK/BL
BL/BK
BK/O
O/BK
BK/G
G/BK
BK/BR
BR/BK
BK/S
S/BK
Y/BL
B/Y
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
1T
1R
1MWB
1MWA
2T
2R
2MWB
2MWA
3T
3R
3MWB
3MWA
4T
4R
4MWB
4MWA
1T
1R
1T(MR)
1R(MR)
2T
2R
2T(MR)
2R(MR)
3T
3R
3T(MR)
3R(MR)
4T
4R
4T(MR)
4R(MR)
1T
1R
1T1
1R1
1E
1SG
1M
1SB
2T
2R
2T1
2R1
2E
2SG
2M
2SB
1T
1R
1T
1R
2T
2R
2T
2R
34
9
35
10
36
11
37
12
38
13
39
14
40
15
41
16
R/BR
BR/R
R/S
S/R
BK/BL
BL/BK
BK/O
O/BK
BK/G
G/BK
BK/BR
BR/BK
BK/S
S/BK
Y/BL
BL/Y
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
5T
5R
5MWB
5MWA
6T
6R
6MWB
6MWA
7T
7R
7MWB
7MWA
8T
8R
8MWB
8MWA
5T
5R
5T(MR)
5R(MR)
6T
6R
6T(MR)
6R(MR)
7T
7R
7T(MR)
7R(MR)
8T
8R
8T(MR)
8R(MR)
3T
3R
3T1
3R1
3E
3SG
3M
3SB
4T
4R
4T1
4R1
4E
4SG
4M
4SB
3T
3R
5T
5R
4T
4R
6T
6R
34
3T
3R
COV
LC
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
7T
7R
8T
8R
9T
9R
10T
10R
11T
11R
12T
12R
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
4T
4R
7T
7R
8T
8R
DNI
LC
Peripheral
Backplane
Plugs
P1
P2
Installation
Table 14: Card Slot 3 Connections to Cross-connect Field
Pin
Color
Code
ONS
LC
OPS
LC
LS/GS
Trunk
E&M
Trunk
DID/LT
Trunk
DID/2
Trunk
COV
LC
Y/O
0/Y
Y/G
G/Y
Y/BR
BR/Y
Y/S
S/Y
V/BL
BL/V
V/O
O/V
V/G
G/V
V/BR
BR/V
---------
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
---------
1T
1R
1MWB
1MWA
2T
2R
2MWB
2MWA
3T
3R
3MWB
3MWA
4T
4R
4MWB
4MWA
---------
1T
1R
1T(MR)
1R(MR)
2T
2R
2T(MR)
2R(MR)
3T
3R
3T(MR)
3R(MR)
4T
4R
4T(MR)
4R(MR)
---------
1T
1R
1T1
1R1
1E
1SG
1M
1SB
2T
2R
2T1
2R1
2E
2SG
2M
2SB
SPARE
SPARE
1T
1R
1T
1R
2T
2R
2T
2R
---------
---------
---------
42
17
43
18
44
19
45
20
46
21
47
22
48
23
49
24
50
25
Y/O
O/Y
Y/G
G/Y
Y/BR
BR/Y
Y/S
S/Y
V/BL
BL/V
V/O
O/V
V/G
G/V
V/BR
BR/V
---------
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
---------
5T
5R
5MWB
5MWA
6T
6R
6MWB
6MWA
7T
7R
7MWB
7MWA
8T
8R
8MWB
8MWA
---------
5T
5R
5T(MR)
5R(MR)
6T
6R
6T(MR)
6R(MR)
7T
7R
7T(MR)
7R(MR)
8T
8R
8T(MR)
8R(MR)
---------
3T
3R
3T1
3R1
3E
3SG
3M
3SB
4T
4R
4T1
4R1
4E
4SG
4M
4SB
SPARE
SPARE
3T
3R
5T
5R
4T
4R
6T
6R
7T
7R
8T
8R
9T
9R
10T
10R
11T
11R
12T
12R
3T
3R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
4T
4R
7T
7R
8T
8R
---------
---------
---------
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
--------9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
---------
Installation
42
17
43
18
44
19
45
20
46
21
47
22
48
23
49
24
50
25
Peripheral
Backplane
Plugs
DNI
LC
P1
P2
35
Technician’s Handbook
Table 15: Card Slot 4 Connections to Cross-connect Field
Color
Code
ONS
LC
26
1
27
2
28
3
29
4
30
5
31
6
32
7
33
8
W/BL
BL/W
W/O
O/W
W/G
G/W
W/BR
BR/W
W/S
S/W
R/BL
BL/R
R/O
O/R
R/G
G/R
26
1
27
2
28
3
29
4
30
5
31
6
32
7
33
8
W/BL
BL/W
W/O
O/W
W/G
G/W
W/BR
BR/W
W/S
S/W
R/BL
BL/R
R/O
O/R
R/G
G/R
Pin
36
OPS
LC
LS/GS
Trunk
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
1T
1R
1MWB
1MWA
2T
2R
2MWB
2MWA
3T
3R
3MWB
3MWA
4T
4R
4MWB
4MWA
1T
1R
1T(MR)
1R(MR)
2T
2R
2T(MR)
2R(MR)
3T
3R
3T(MR)
3R(MR)
4T
4R
4T(MR)
4R(MR)
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
5T
5R
5MWB
5MWA
6T
6R
6MWB
6MWA
7T
7R
7MWB
7MWA
8T
8R
8MWB
8MWA
5T
5R
5T(MR)
5R(MR)
6T
6R
6T(MR)
6R(MR)
7T
7R
7T(MR)
7R(MR)
8T
8R
8T(MR)
8R(MR)
DID/
LT
Trunk
DID/2
Trunk
COV
LC
1T
1R
1T1
1R1
1E
1SG
1M
1SB
2T
2R
2T1
2R1
2E
2SG
2M
2SB
1T
1R
1T
1R
2T
2R
2T
2R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
3T
3R
3T1
3R1
3E
3SG
3M
3SB
4T
4R
4T1
4R1
4E
4SG
4M
4SB
3T
3R
5T
5R
4T
4R
6T
6R
7T
7R
8T
8R
9T
9R
10T
10R
11T
11R
12T
12R
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
E&M
Trunk
3T
3R
4T
4R
7T
7R
8T
8R
DNI
LC
Peripheral
Backplane
Plugs
P3
P4
Installation
Table 16: Card Slot 5 Connections to Cross-connect Field
Pin
Color
Code
ONS
LC
OPS
LC
LS/GS
Trunk
E&M
Trunk
DID/LT
Trunk
DID/2
Trunk
R/BR
BR/R
R/S
S/R
BK/BL
BL/BK
BK/O
O/BK
BK/G
G/BK
BK/BR
BR/BK
BK/S
S/BK
Y/BL
B/Y
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
1T
1R
1MWB
1MWA
2T
2R
2MWB
2MWA
3T
3R
3MWB
3MWA
4T
4R
4MWB
4MWA
1T
1R
1T(MR)
1R(MR)
2T
2R
2T(MR)
2R(MR)
3T
3R
3T(MR)
3R(MR)
4T
4R
4T(MR)
4R(MR)
1T
1R
1T1
1R1
1E
1SG
1M
1SB
2T
2R
2T1
2R1
2E
2SG
2M
2SB
1T
1R
1T
1R
2T
2R
2T
2R
34
9
35
10
36
11
37
12
38
13
39
14
40
15
41
16
R/BR
BR/R
R/S
S/R
BK/BL
BL/BK
BK/O
O/BK
BK/G
G/BK
BK/BR
BR/BK
BK/S
S/BK
Y/BL
BL/Y
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
5T
5R
5MWB
5MWA
6T
6R
6MWB
6MWA
7T
7R
7MWB
7MWA
8T
8R
8MWB
8MWA
5T
5R
5T(MR)
5R(MR)
6T
6R
6T(MR)
6R(MR)
7T
7R
7T(MR)
7R(MR)
8T
8R
8T(MR)
8R(MR)
3T
3R
3T1
3R1
3E
3SG
3M
3SB
4T
4R
4T1
4R1
4E
4SG
4M
4SB
3T
3R
5T
5R
4T
4R
6T
6R
3T
3R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
7T
7R
8T
8R
9T
9R
10T
10R
11T
11R
12T
12R
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
4T
4R
7T
7R
8T
8R
DNI
LC
Peripheral
Backplane
Plugs
Installation
34
9
35
10
36
11
37
12
38
13
39
14
40
15
41
16
COV
LC
P3
P4
37
Technician’s Handbook
Table 17: Card Slot 6 Connections to Cross-connect Field
Pin
Color
Code
ONS
LC
OPS
LC
LS/GS
Trunk
E&M
Trunk
DID/LT
Trunk
DID/2
Trunk
COV
LC
42
17
43
18
44
19
45
20
46
21
47
22
48
23
49
24
50
25
Y/O
0/Y
Y/G
G/Y
Y/BR
BR/Y
Y/S
S/Y
V/BL
BL/V
V/O
O/V
V/G
G/V
V/BR
BR/V
---------
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
---------
1T
1R
1MWB
1MWA
2T
2R
2MWB
2MWA
3T
3R
3MWB
3MWA
4T
4R
4MWB
4MWA
---------
1T
1R
1T(MR)
1R(MR)
2T
2R
2T(MR)
2R(MR)
3T
3R
3T(MR)
3R(MR)
4T
4R
4T(MR)
4R(MR)
---------
1T
1R
1T1
1R1
1E
1SG
1M
1SB
2T
2R
2T1
2R1
2E
2SG
2M
2SB
SPARE
SPARE
1T
1R
1T
1R
2T
2R
2T
2R
---------
---------
---------
42
17
43
18
44
19
45
20
46
21
47
22
48
23
49
24
50
25
Y/O
O/Y
Y/G
G/Y
Y/BR
BR/Y
Y/S
S/Y
V/BL
BL/V
V/O
O/V
V/G
G/V
V/BR
BR/V
---------
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
---------
5T
5R
5MWB
5MWA
6T
6R
6MWB
6MWA
7T
7R
7MWB
7MWA
8T
8R
8MWB
8MWA
---------
5T
5R
5T(MR)
5R(MR)
6T
6R
6T(MR)
6R(MR)
7T
7R
7T(MR)
7R(MR)
8T
8R
8T(MR)
8R(MR)
---------
3T
3R
3T1
3R1
3E
3SG
3M
3SB
4T
4R
4T1
4R1
4E
4SG
4M
4SB
SPARE
SPARE
3T
3R
5T
5R
4T
4R
6T
6R
7T
7R
8T
8R
9T
9R
10T
10R
11T
11R
12T
12R
38
3T
3R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
4T
4R
7T
7R
8T
8R
---------
---------
---------
DNI
LC
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
--------9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
---------
Peripheral
Backplane
Plugs
P3
P4
Installation
Table 18: Card Slot 7 Connections to Cross-connect Field
Pin
Color
Code
ONS
LC
OPS
LC
LS/GS
Trunk
E&M
Trunk
DID/LT
Trunk
DID/2
Trunk
W/BL
BL/W
W/O
O/W
W/G
G/W
W/BR
BR/W
W/S
S/W
R/BL
BL/R
R/O
O/R
R/G
G/R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
1T
1R
1MWB
1MWA
2T
2R
2MWB
2MWA
3T
3R
3MWB
3MWA
4T
4R
4MWB
4MWA
1T
1R
1T(MR)
1R(MR)
2T
2R
2T(MR)
2R(MR)
3T
3R
3T(MR)
3R(MR)
4T
4R
4T(MR)
4R(MR)
1T
1R
1T1
1R1
1E
1SG
1M
1SB
2T
2R
2T1
2R1
2E
2SG
2M
2SB
1T
1R
1T
1R
2T
2R
2T
2R
26
1
27
2
28
3
29
4
30
5
31
6
32
7
33
8
W/BL
BL/W
W/O
O/W
W/G
G/W
W/BR
BR/W
W/S
S/W
R/BL
BL/R
R/O
O/R
R/G
G/R
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
5T
5R
5MWB
5MWA
6T
6R
6MWB
6MWA
7T
7R
7MWB
7MWA
8T
8R
8MWB
8MWA
5T
5R
5T(MR)
5R(MR)
6T
6R
6T(MR)
6R(MR)
7T
7R
7T(MR)
7R(MR)
8T
8R
8T(MR)
8R(MR)
3T
3R
3T1
3R1
3E
3SG
3M
3SB
4T
4R
4T1
4R1
4E
4SG
4M
4SB
3T
3R
5T
5R
4T
4R
6T
6R
3T
3R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
7T
7R
8T
8R
9T
9R
10T
10R
11T
11R
12T
12R
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
4T
4R
7T
7R
8T
8R
DNI
LC
Peripheral
Backplane
Plugs
Installation
26
1
27
2
28
3
29
4
30
5
31
6
32
7
33
8
COV
LC
P5
P6
39
Technician’s Handbook
Table 19: Card Slot 8 Connections to Cross-connect Field
Pin
Color
Code
ONS
LC
OPS
LC
LS/GS
Trunk
E&M
Trunk
DID/LT
Trunk
DID/2
Trunk
34
9
35
10
36
11
37
12
38
13
39
14
40
15
41
16
R/BR
BR/R
R/S
S/R
BK/BL
BL/BK
BK/O
O/BK
BK/G
G/BK
BK/BR
BR/BK
BK/S
S/BK
Y/BL
B/Y
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
1T
1R
1MWB
1MWA
2T
2R
2MWB
2MWA
3T
3R
3MWB
3MWA
4T
4R
4MWB
4MWA
1T
1R
1T(MR)
1R(MR)
2T
2R
2T(MR)
2R(MR)
3T
3R
3T(MR)
3R(MR)
4T
4R
4T(MR)
4R(MR)
1T
1R
1T1
1R1
1E
1SG
1M
1SB
2T
2R
2T1
2R1
2E
2SG
2M
2SB
1T
1R
1T
1R
2T
2R
2T
2R
34
9
35
10
36
11
37
12
38
13
39
14
40
15
41
16
R/BR
BR/R
R/S
S/R
BK/BL
BL/BK
BK/O
O/BK
BK/G
G/BK
BK/BR
BR/BK
BK/S
S/BK
Y/BL
BL/Y
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
5T
5R
5MWB
5MWA
6T
6R
6MWB
6MWA
7T
7R
7MWB
7MWA
8T
8R
8MWB
8MWA
5T
5R
5T(MR)
5R(MR)
6T
6R
6T(MR)
6R(MR)
7T
7R
7T(MR)
7R(MR)
8T
8R
8T(MR)
8R(MR)
3T
3R
3T1
3R1
3E
3SG
3M
3SB
4T
4R
4T1
4R1
4E
4SG
4M
4SB
3T
3R
5T
5R
4T
4R
6T
6R
40
3T
3R
COV
LC
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
7T
7R
8T
8R
9T
9R
10T
10R
11T
11R
12T
12R
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
4T
4R
7T
7R
8T
8R
DNI
LC
Peripheral
Backplane
Plugs
P5
P6
Installation
Table 20: Card Slot 9 Connections to Cross-connect Field
Pin
Color
Code
ONS
LC
OPS
LC
LS/GS
Trunk
E&M
Trunk
DID/LT
Trunk
DID/2
Trunk
COV
LC
Y/O
0/Y
Y/G
G/Y
Y/BR
BR/Y
Y/S
S/Y
V/BL
BL/V
V/O
O/V
V/G
G/V
V/BR
BR/V
---------
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
---------
1T
1R
1MWB
1MWA
2T
2R
2MWB
2MWA
3T
3R
3MWB
3MWA
4T
4R
4MWB
4MWA
---------
1T
1R
1T(MR)
1R(MR)
2T
2R
2T(MR)
2R(MR)
3T
3R
3T(MR)
3R(MR)
4T
4R
4T(MR)
4R(MR)
---------
1T
1R
1T1
1R1
1E
1SG
1M
1SB
2T
2R
2T1
2R1
2E
2SG
2M
2SB
SPARE
SPARE
1T
1R
1T
1R
2T
2R
2T
2R
---------
---------
---------
42
17
43
18
44
19
45
20
46
21
47
22
48
23
49
24
50
25
Y/O
O/Y
Y/G
G/Y
Y/BR
BR/Y
Y/S
S/Y
V/BL
BL/V
V/O
O/V
V/G
G/V
V/BR
BR/V
---------
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
---------
5T
5R
5MWB
5MWA
6T
6R
6MWB
6MWA
7T
7R
7MWB
7MWA
8T
8R
8MWB
8MWA
---------
5T
5R
5T(MR)
5R(MR)
6T
6R
6T(MR)
6R(MR)
7T
7R
7T(MR)
7R(MR)
8T
8R
8T(MR)
8R(MR)
---------
3T
3R
3T1
3R1
3E
3SG
3M
3SB
4T
4R
4T1
4R1
4E
4SG
4M
4SB
SPARE
SPARE
3T
3R
5T
5R
4T
4R
6T
6R
7T
7R
8T
8R
9T
9R
10T
10R
11T
11R
12T
12R
3T
3R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
4T
4R
7T
7R
8T
8R
---------
---------
---------
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
--------9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
---------
Peripheral
Backplane
Plugs
Installation
42
17
43
18
44
19
45
20
46
21
47
22
48
23
49
24
50
25
DNI
LC
P5
P6
41
Technician’s Handbook
Table 21: Card Slot 10 Connections to Cross-connect Field
Pin
Color
Code
ONS
LC
OPS
LC
LS/GS
Trunk
E&M
Trunk
DID/LT
Trunk
DID/2
Trunk
26
1
27
2
28
3
29
4
30
5
31
6
32
7
33
8
W/BL
BL/W
W/O
O/W
W/G
G/W
W/BR
BR/W
W/S
S/W
R/BL
BL/R
R/O
O/R
R/G
G/R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
1T
1R
1MWB
1MWA
2T
2R
2MWB
2MWA
3T
3R
3MWB
3MWA
4T
4R
4MWB
4MWA
1T
1R
1T(MR)
1R(MR)
2T
2R
2T(MR)
2R(MR)
3T
3R
3T(MR)
3R(MR)
4T
4R
4T(MR)
4R(MR)
1T
1R
1T1
1R1
1E
1SG
1M
1SB
2T
2R
2T1
2R1
2E
2SG
2M
2SB
1T
1R
1T
1R
2T
2R
2T
2R
26
1
27
2
28
3
29
4
30
5
31
6
32
7
33
8
W/BL
BL/W
W/O
O/W
W/G
G/W
W/BR
BR/W
W/S
S/W
R/BL
BL/R
R/O
O/R
R/G
G/R
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
5T
5R
5MWB
5MWA
6T
6R
6MWB
6MWA
7T
7R
7MWB
7MWA
8T
8R
8MWB
8MWA
5T
5R
5T(MR)
5R(MR)
6T
6R
6T(MR)
6R(MR)
7T
7R
7T(MR)
7R(MR)
8T
8R
8T(MR)
8R(MR)
3T
3R
3T1
3R1
3E
3SG
3M
3SB
4T
4R
4T1
4R1
4E
4SG
4M
4SB
3T
3R
5T
5R
4T
4R
6T
6R
42
3T
3R
COV
LC
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
7T
7R
8T
8R
9T
9R
10T
10R
11T
11R
12T
12R
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
4T
4R
7T
7R
8T
8R
DNI
LC
Peripheral
Backplane
Plugs
P7
P8
Installation
Table 22: Card Slot 11 Connections to Cross-connect Field
Pin
Color
Code
ONS
LC
OPS
LC
LS/GS
Trunk
E&M
Trunk
DID/LT
Trunk
DID/2
Trunk
R/BR
BR/R
R/S
S/R
BK/BL
BL/BK
BK/O
O/BK
BK/G
G/BK
BK/BR
BR/BK
BK/S
S/BK
Y/BL
B/Y
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
1T
1R
1MWB
1MWA
2T
2R
2MWB
2MWA
3T
3R
3MWB
3MWA
4T
4R
4MWB
4MWA
1T
1R
1T(MR)
1R(MR)
2T
2R
2T(MR)
2R(MR)
3T
3R
3T(MR)
3R(MR)
4T
4R
4T(MR)
4R(MR)
1T
1R
1T1
1R1
1E
1SG
1M
1SB
2T
2R
2T1
2R1
2E
2SG
2M
2SB
1T
1R
1T
1R
2T
2R
2T
2R
34
9
35
10
36
11
37
12
38
13
39
14
40
15
41
16
R/BR
BR/R
R/S
S/R
BK/BL
BL/BK
BK/O
O/BK
BK/G
G/BK
BK/BR
BR/BK
BK/S
S/BK
Y/BL
BL/Y
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
5T
5R
5MWB
5MWA
6T
6R
6MWB
6MWA
7T
7R
7MWB
7MWA
8T
8R
8MWB
8MWA
5T
5R
5T(MR)
5R(MR)
6T
6R
6T(MR)
6R(MR)
7T
7R
7T(MR)
7R(MR)
8T
8R
8T(MR)
8R(MR)
3T
3R
3T1
3R1
3E
3SG
3M
3SB
4T
4R
4T1
4R1
4E
4SG
4M
4SB
3T
3R
5T
5R
4T
4R
6T
6R
3T
3R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
7T
7R
8T
8R
9T
9R
10T
10R
11T
11R
12T
12R
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
4T
4R
7T
7R
8T
8R
DNI
LC
Peripheral
Backplane
Plugs
Installation
34
9
35
10
36
11
37
12
38
13
39
14
40
15
41
16
COV
LC
P7
P8
43
Technician’s Handbook
Table 23: Card Slot 12 Connections to Cross-connect Field
Pin
Color
Code
ONS
LC
OPS
LC
LS/GS
Trunk
E&M
Trunk
DID/LT
Trunk
DID/2
Trunk
COV
LC
42
17
43
18
44
19
45
20
46
21
47
22
48
23
49
24
50
25
Y/O
0/Y
Y/G
G/Y
Y/BR
BR/Y
Y/S
S/Y
V/BL
BL/V
V/O
O/V
V/G
G/V
V/BR
BR/V
---------
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
---------
1T
1R
1MWB
1MWA
2T
2R
2MWB
2MWA
3T
3R
3MWB
3MWA
4T
4R
4MWB
4MWA
---------
1T
1R
1T(MR)
1R(MR)
2T
2R
2T(MR)
2R(MR)
3T
3R
3T(MR)
3R(MR)
4T
4R
4T(MR)
4R(MR)
---------
1T
1R
1T1
1R1
1E
1SG
1M
1SB
2T
2R
2T1
2R1
2E
2SG
2M
2SB
SPARE
SPARE
1T
1R
1T
1R
2T
2R
2T
2R
---------
---------
---------
42
17
43
18
44
19
45
20
46
21
47
22
48
23
49
24
50
25
Y/O
O/Y
Y/G
G/Y
Y/BR
BR/Y
Y/S
S/Y
V/BL
BL/V
V/O
O/V
V/G
G/V
V/BR
BR/V
---------
9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
---------
5T
5R
5MWB
5MWA
6T
6R
6MWB
6MWA
7T
7R
7MWB
7MWA
8T
8R
8MWB
8MWA
---------
5T
5R
5T(MR)
5R(MR)
6T
6R
6T(MR)
6R(MR)
7T
7R
7T(MR)
7R(MR)
8T
8R
8T(MR)
8R(MR)
---------
3T
3R
3T1
3R1
3E
3SG
3M
3SB
4T
4R
4T1
4R1
4E
4SG
4M
4SB
SPARE
SPARE
3T
3R
5T
5R
4T
4R
6T
6R
7T
7R
8T
8R
9T
9R
10T
10R
11T
11R
12T
12R
44
3T
3R
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
4T
4R
7T
7R
8T
8R
---------
---------
---------
DNI
LC
1T
1R
2T
2R
3T
3R
4T
4R
5T
5R
6T
6R
7T
7R
8T
8R
--------9T
9R
10T
10R
11T
11R
12T
12R
13T
13R
14T
14R
15T
15R
16T
16R
---------
Peripheral
Backplane
Plugs
P7
P8
Chapter 3
Programming
45
Technician’s Handbook
46
Programming
Programming Class of Service,
Interconnect Restriction, and Intercept
Handling
1. Class of Service Options Assignment form
!
Create a unique class of service which defines
privileges and timers and is assigned to a set or trunk
to determine it’s operation. The default for all sets
and trunks is COS 1.
!
Set the interconnect restrictions to allow or deny
device connection. The default for all devices, sets,
and trunks is interconnect restriction 1(no
restrictions).
3. Intercept Handling Assignment form
!
Program the system to take action when callers
commit call violations. Callers are routed when
predefined conditions are met. The default for all sets
and trunks is intercept 1.
47
Programming
2. Interconnect Restriction Table
Technician’s Handbook
Programming Printer Ports
System Printer Port
1. System Port Assignment form
!
Assign a logical name to the system printer port
(LPR1 appears automatically in this form).
2. Application Logical Port Assignment form
!
Assign the system printer port name (LPR1) to each
application from which you would like to print reports.
SUPERSET 700 Printer Port
1. DNI Circuit Assignment form
!
Assign a SUPERSET 7 to channel #1 and channel
#2 of the circuit.
2. System Port Assignment form
!
Assign a port name to the PLID of the console’s
output channel (channel #2).
3. Application Logical Port Assignment form
!
48
Assign the port name to each application from which
you would like to print reports.
Programming
SUPERCONSOLE 1000® Printer Port
1. DNI Circuit Assignment form
!
Assign a SUPERCONSOLE 1000 (SC1000) to
channel #1 and a SUPERCONSOLE 1000 port
(SC1000 PORT) to channel #2.
2. Dataset Circuit Descriptor Assignment form
!
Create a circuit descriptor.
!
Set Device Class = SC1000Port
!
Set Defaults = Yes.
Programming
3. Dataset Assignment form
!
Assign Port = YES against the console’s PLID.
!
Assign the circuit descriptor to the console.
!
Assign an interconnect number to the console.
4. System Port Assignment form
!
Assign a port name to the PLID of the console’s
output channel (channel #2).
5. Application Logical Port Assignment form
!
Assign the port name to each application from which
you would like to print reports.
49
Technician’s Handbook
SUPERCONSOLE 2000™ Printer Port
1. Ensure the computer’s COM 1 port is not assigned to
other applications. See the Microsoft Windows documentation for more information.
2. DNI Circuit Assignment form
!
Assign a SUPERCONSOLE 2000 to channel #1 and
channel #2 of the circuit.
3. System Port Assignment form
!
Assign a port name to the PLID of the console’s
output channel (channel #2).
4. Application Logical Port Assignment form
!
50
Assign the port name to each application from which
you would like to print reports.
Programming
DATASET Printer Port
1. DNI Circuit Assignment form
!
Assign DS110x or DS210x against channel #2 of the
required PLID.
2. Dataset Circuit Descriptor Assignment form
!
Create a circuit descriptor.
!
Set Device Class = DS1100s or DS2100s.
!
Set Defaults = Yes.
!
Assign Port = YES against the dataset’s PLID.
!
Assign the circuit descriptor to the dataset.
!
Assign an interconnect number to the dataset.
Programming
3. Dataset Assignment form
4. System Port Assignment form
!
Assign a port name to the PLID of the DATASET’s
output channel (channel #2).
5. Application Logical Port Assignment form
!
Assign the port name to each application from which
you would like to print reports.
51
Technician’s Handbook
Programming Peripheral Devices
Single Line Telephones
Before You Begin
Program Class of Service, Interconnect Restriction, and
Intercept Handling (see page 47).
1. System Configuration form
!
For standard telephones, add an ONS, ONS
CLASS/CLIP, or OPS line card.
!
For SUPERSET 401+ or SUPERSET 4001
telephones, add a DNI line card.
2. For SUPERSET 401+ and SUPERSET 4001
telephones:
DNI Circuit Assignment form
!
Program the set type to channel #1 of the circuit.
For standard telephones:
ONS/OPS Circuit Descriptor form
!
Change the circuit descriptor contents (if required).
!
For OPS circuits, change the transmission parameter
to LONG.
!
For ONS circuits, change the transmission
parameter to SHORT.
Note: The SUPERSET 401 telephone does not have a
descriptor.
52
Programming
3. Single Line Set Assignment form
!
Assign a directory number, circuit descriptor number,
and interconnect number to the circuit.
4. (Optional) Default Account Code Definition form
!
Create a default account code number that will
appear in all SMDR records for the station.
5. Station Service Assignment form
Assign the telephone’s directory number a class of
service, class of restriction, and intercept number.
!
(Optional) Assign a default account code index
number.
Programming
!
53
Technician’s Handbook
Analog Devices Connected to an AIM
Before You Begin
Program Class of Service, Interconnect Restriction, and
Intercept Handling (see page 47).
To program analog devices connected to a Mitel Networks
5422 Analog Interface Module:
1. System Configuration form
!
Program a DNI line card.
2. DNI Circuit Assignment form
!
Program set type against channel #1 of the circuit.
!
Program the AIM against channel #2 of the circuit.
3. ONS/OPS Circuit Descriptor Assignment form
!
Change circuit descriptor contents (if required).
!
Change the transmission parameter to SHORT.
4. Single Line Set Assignment form
!
Assign a directory number, circuit descriptor number,
and interconnect number to the circuit.
5. Default Account Code Definition form (Optional)
!
Create a default account code number that will
appear in all SMDR records for the station.
6. Station Service Assignment form
54
!
Assign the telephone’s directory number a Class of
Service, Class of Restriction, and Intercept Number.
!
(Optional) Assign a Default Account Code Index
Number.
Programming
Multiline Telephones
Before You Begin
Program Class of Service, Interconnect Restriction, and
Intercept Handling (see page 47).
1. System Configuration form
!
Program a COV or DNI line card.
2. DNI Circuit Assignment form
Note: This step does not apply to SUPERSET 4 telephones.
Program the set type to channel #1 of the circuit.
!
If the telephone connects to a PKM, program the
PKM to channel #2. If the telephone connects to an
analog device, program the AIM to channel #2.
If you program the AIM to channel #2, you must also
program the connected analog devices. See Analog
Devices Connected to an AIM on page 54.
3. Multiline Set Assignment form
!
Program a prime directory number and an
interconnect number to a line circuit.
4. Multiline Set Key Assignment form (Optional)
!
Assign a directory number (line appearance) or
feature to each key.
!
Assign each line appearance a ring type.
5. Multiline Set Group Assignment form (Optional)
!
Change the ring type at each telephone where the
number appears.
!
Change the group type from “key system” to
“multicall” or vice versa.
55
Programming
!
Technician’s Handbook
6. Default Account Code Definition form (Optional)
!
Create a default account code number that will
appear in all SMDR records for the station.
7. Station Service Assignment form
!
Assign the telephone’s directory number a class of
service, class of restriction, and intercept number.
!
(Optional) Assign a default account code index
number.
Programmable Key Module
The PKM12, PKM48, and Dual PKM are programmed in the
same way. You can only program the first 12 keys on a
PKM12.
1. DNI Circuit Assignment form
!
Locate the PLID of the device to which the PKM is
connected.
!
Select "PKM12", "PKM48", or "Dual PKM" in the
Channel #2 field.
2. Multiline Set Key Assignment form
!
Program the keys.
Upgrade a PKM
To change your PKM12 to PKM48, Dual PKM, or add a
second PKM48 to a SUPERSET 4025 or SUPERSET 4150:
1. DNI Circuit Assignment form
!
Locate the PLID of the PKM-connected device.
!
Change the PKM type in the Channel #2 field.
2. Multiline Set Key Assignment form
!
56
Program the additional keys.
Programming
Attendant Consoles
Before You Begin
Program Class of Service, Interconnect Restriction, and
Intercept Handling (see page 47).
1. System Configuration form
!
Add a DNI line card.
2. DNI Circuit Assignment form
For a SUPERCONSOLE 1000 or SUPERSET 7000,
program the set type to channel #1 of a DNI circuit.
!
For a SUPERSET 700, program SUPERSET 7 to
channels #1 and #2 of a DNI circuit.
!
For a SUPERCONSOLE 2000, program SC2000 to
channels #1 and #2 of a DNI circuit.
3. Attendant Assignment form
!
Assign a prime directory number to the console
circuit PLID and a key appearance.
4. Attendant Softkey Assignment form
!
Recall the prime directory number of the console.
!
Assign directory numbers to the console softkeys
(key #1 is reserved for recall functions).
5. Telephone Directory form
!
Assign names to the console softkey directory
numbers.
6. (Optional) Default Account Code Definition form
!
Create a default account code number that will
appear in all SMDR records for the station.
57
Programming
!
Technician’s Handbook
7. Station Service Assignment form
58
!
Assign the console’s directory number a class of
service, class of restriction, and intercept number.
!
(Optional) Assign a default account code index
number.
Programming
Programming the Telephone Directory
Telephone Directory form
Assign a name to the telephone’s directory number.
!
If more than one name is assigned to the same
telephone number, enter “Y” in the Prime Name field
to indicate the prime name.
!
If the telephone number is not to appear on the
display of other telephones during a call, enter “Y” in
the Prv # field.
!
(Optional) Assign a department and location name to
the telephone’s directory number.
59
Programming
!
Technician’s Handbook
Changing a Telephone’s Attributes
1. Change Attribute Assignment form
!
Enter the directory number of the device and recall
the form.
2. Change any of the following database parameters:
!
Department name for the user
!
Location of the user
!
Default account code index number
!
Intercept number
!
Interconnect number
!
Circuit descriptor
!
Class of service and class of restriction
!
Maximum number of speedcalls available
!
Pickup group number
!
Station hotline number
!
Associated dataline number
!
1st, 2nd, and Always call rerouting numbers
To move a user from one telephone to another, or to
exchange telephones between two users, use the MOVE
command, rather than the Change Attribute Assignment
form. See Moving a Telephone User on page 61.
60
Programming
Moving a Telephone User
Use the MOVE USER command to move a user from one
telephone to another. Enter the command in the following
format:
MOVE USER <station A’s extension #> TO <station B’s
extension #>
MOVE USER <Station A> TO <Station B>
Stn A = attribute of Station A before the move
Stn B = attribute of Station B before the move
Telephone Features
Station B
deleted
Stn A, Stn B
Department
deleted
Stn A, Stn B
Location
deleted
Stn A, Stn B
Default Account Code
deleted
Stn A
Personal Speedcalls Allocated
deleted
Stn A
Personal Speedcalls Used
deleted
Stn A
Personal Speedcall Numbers
deleted
The following attributes change only at Station B:
Intercept Number
same
Stn A
Interconnect Number
same
Stn A
Class of Service
same
Stn A
Stn A
Class of Restriction
same
The following attributes remain unchanged at both sets:
Directory Number
same
same
Circuit Descriptor
same
same
Hunt Group Pilot Number
same
same
Pickup Group Number
same
same
Station Hotline Number
same
same
Associated Data Line Number
same
same
Call Announce Number
same
same
Call Rerouting
same
same
Button Speedcalls
same
same
Call Forward Settings
same
same
Message Waiting
same
same
Do Not Disturb
same
same
Auto Answer
same
same
same
Baud Rate / Parity
Programming
Station A
The following attributes change at both sets:
Name
Stn A
same
61
Technician’s Handbook
Swapping Users’ Telephones
Use the MOVE SWAP command to swap two users’
telephones. Enter the command in the following format:
MOVE SWAP <station A’s extension #> WITH <station B’s
extension #>
MOVE SWAP <Station A> WITH <Station B>
Stn A = attribute of Station A before the move
Stn B = attribute of Station B before the move
Telephone Features
Station A
The following attributes are exchanged between the sets:
Directory Number
Stn B
Name
Stn B
Department
Stn B
Location
Stn B
Default Account Code
Stn B
Personal Speedcalls Allocated
Stn B
Personal Speedcalls Used
Stn B
Personal Speedcall Numbers
Stn B
Intercept Number
Stn B
Interconnect Number
Stn B
Class of Service
Stn B
Class of Restriction
Stn B
Call Rerouting
Stn B
Hunt Group Pilot Number
Stn B
Button Speedcalls
Stn B
Call Forward Settings
Stn B
Message Waiting
Stn B
The following attributes remain the same at both sets:
Circuit Descriptor
same
Pickup Group Number
same
Station Hotline Number
same
Associated Data Line Number
same
Do Not Disturb
same
Auto Answer
same
Baud Rate / Parity
same
62
Station B
Stn A
Stn A
Stn A
Stn A
Stn A
Stn A
Stn A
Stn A
Stn A
Stn A
Stn A
Stn A
Stn A
Stn A
Stn A
Stn A
Stn A
same
same
same
same
same
same
same
Programming
Programming Call Rerouting
1. Call Rerouting Always Alternative Assignment form
!
For First Always Alternative Number 1
—
!
Leave all values as “Normal”
For each Always Alternative Number
Change “No Reroute” to “Reroute” for the
required originating device(s).
—
Enter the directory number to which calls should
reroute.
2. Call Rerouting First Alternative Assignment form
!
For First Alternative Number 1
—
!
Leave all values as “Normal”.
For other First Alternative Numbers
—
If calls from an originating device type are to
reroute to the First Alternative in Busy or Do Not
Disturb conditions, set the value to “This”.
—
If calls from an originating device type are to
reroute to the First Alternative in No Answer
conditions, set the value to “This”.
—
If calls from an originating device type are to
reroute directly to the Second Alternative in Busy
or Do Not Disturb conditions, set the value to
“Last”.
—
If calls from an originating device type are to
reroute directly to the Second Alternative in No
Answer conditions, set the value to “Last”.
—
Enter the directory number to which calls should
reroute.
63
Programming
—
Technician’s Handbook
3. Call Rerouting Second Alternative Assignment
!
For Second Alternative Number 1
—
!
Leave all values as “Normal”.
For other Second Alternative Numbers
—
If calls from an originating device type are to
reroute directly to the Second Alternative in Busy,
Do Not Disturb, or No Answer conditions, set the
value to “This” or “Last”.
—
Enter the directory number to which calls should
reroute.
4. Call Rerouting Assignment form
!
64
For each directory number that is affected by Call
Rerouting, enter the Always Alternative Number for
Day Service, Night Service 1, and Night Service 2, as
well as the First and Second Alternative Numbers.
Programming
Programming Trunks
Analog Dial-in Trunk
Before You Begin
Program Class of Service, Interconnect Restriction, and
Intercept Handling (see page 47).
1. Trunk Circuit Descriptor Assignment form
!
2. Trunk Service Assignment form
!
Create a trunk service number:
—
Assign a class of service.
—
Assign a class of restriction.
—
Leave the Answer Points columns blank.
—
To absorb no incoming digits, set the Absorb
column to 0. Do not leave it blank.
—
To absorb n digits, enter n (n =a whole number)
in the Absorb column.
—
To insert no digits, leave the Insert column blank.
—
To insert digits, enter the actual digits to be
inserted in the Insert column.
—
(Optional) Assign a trunk label to appear on
display telephones and attendant consoles
during incoming and outgoing calls.
65
Programming
There are several Trunk Circuit Descriptor
Assignment forms. Use the specific form for the type
of trunk that you are programming, to create a Trunk
Circuit Descriptor.
Technician’s Handbook
3. Trunk Assignment form
!
Assign the trunk a trunk number, trunk service
number, and trunk circuit descriptor number.
!
Assign the trunk an interconnect number.
4. Trunk Group Assignment form
!
For an outgoing trunk, enter the trunk number in the
desired trunk group.
Analog Non-dial-in Trunk
Before You Begin
Program Class of Service, Interconnect Restriction, and
Intercept Handling (see page 47).
1. Trunk Circuit Descriptor Assignment form
!
There are several Trunk Circuit Descriptor
Assignment forms. Use the specific form for the type
of trunk that you are programming, to create a Trunk
Circuit Descriptor.
2. Trunk Service Assignment form
!
66
Create a trunk service number:
—
Assign a class of service.
—
Assign a class of restriction.
—
Specify the directory number that incoming calls
will ring during Day Service, Night Service 1, and
Night Service 2.
—
Leave the Digit Modification columns blank.
—
(Optional) Assign a trunk label to appear on
display telephones and attendant consoles
during incoming and outgoing calls.
Programming
3. Trunk Assignment form
!
Assign the trunk a trunk number, trunk service
number, and trunk circuit descriptor number.
!
Assign the trunk an interconnect number.
4. Trunk Group Assignment form
!
For an outgoing trunk, enter the trunk number in the
desired trunk group.
DISA Dial-in Trunk
1. Miscellaneous Assignment form
Create a DISA forced account code number
- or -
!
Create a plain DISA number for the dial-in trunk.
Programming
!
2. Independent Account Code Assignment form
!
If you are using a DISA forced account code number
for the trunk, create an independent account code
number and assign it to the appropriate class of
service and class of restriction.
3. Trunk Service Assignment form
!
If you are using a DISA number without a forced
account code for the trunk, assign the appropriate
class of restriction.
!
If you do not want to modify the incoming digits, set
the Absorb column to 0 (do not leave it blank) and
leave the Insert column blank.
4. Trunk Assignment form
!
Assign the trunk service number to the dial-in trunks.
67
Technician’s Handbook
DISA Non-dial-in Trunk
1. Miscellaneous Assignment form
!
Create a DISA forced account code number
- or -
!
Create a plain DISA number for the non-dial-in trunk.
2. Independent Account Code Assignment form
!
If you are using a DISA forced account code number
for the trunk, create an independent account code
number and assign it to the appropriate class of
service and class of restriction.
3. Trunk Service Assignment form
!
Select a trunk service number.
!
If you are using a DISA number without a forced
account code for the trunk, assign the appropriate
class of restriction.
!
Assign a DISA number, created in step 1, as an
Answer Point (specify the DISA directory for Day,
Night 1, and Night 2 service).
4. Trunk Assignment form
!
Assign the trunk service number to the desired
trunks.
Digital Trunk
Two DSU cabinets may be programmed in a single DSU
node. On the left side of the node, slots 1, 2, and 3 comprise
one DSU cabinet. On the right side of the node, slots 4, 5,
and 6 comprise another DSU cabinet. When you program
cards in the left cabinet, program slot 3 before slot 2. When
you program cards in the right cabinet, program slot 5 before
slot 4. If you do not follow this order of programming, the
DSU cards on the side of the node that you are programming
will reset when you add the second card and the cabinet will
go out of service for one or two minutes.
68
Programming
Before You Begin
Program Class of Service, Interconnect Restriction, and
Intercept Handling (see page 47).
1. System Configuration form
!
Program a DS1 formatter, CEPT formatter, PRI,
T1/E1, Universal T1/E1, or R2 card. Note that the
system will not recognize the card until it is assigned
a link descriptor in step 3.
2. Link Descriptor Assignment form
!
Create a link descriptor number.
!
Assign the link descriptor number to the link. (Until
you assign it, the link’s trunks do not appear in the
Trunk Assignment form.)
4. Digital Trunk Circuit Descriptor Assignment form
!
There are several Digital Trunk Circuit Descriptor
Assignment forms. Use the specific form for the type
of trunk that you are programming, to create a Trunk
Circuit Descriptor.
5. Trunk Service Assignment form
!
Create a trunk service number to specify an answer
point for incoming calls on non-dial-in trunks.
!
If the trunks are dial-in trunks, specify how the
incoming digits should be handled.
6. Trunk Assignment form
!
Assign the trunk circuit descriptor and trunk service
number to the trunks.
69
Programming
3. Digital Link Assignment form
Technician’s Handbook
7. Trunk Group Assignment form
!
For an outgoing trunk, enter the trunk number in the
desired trunk group.
8. Network Synchronization form
!
70
Enter the PLIDs of the links which will be
synchronization sources for the system.
Programming
Programming Automatic Route
Selection (ARS)
1. Trunk Group Assignment form
!
Create a trunk group number
!
Assign trunks to the trunk group.
2. (Optional) Call Progress Tone Detection Plan
Assignment form
!
3. Digit Modification Assignment form
!
For each digit modification number, specify the
number of dialed digits to absorb and the digit(s) to
be inserted.
4. Class of Restriction Group Assignment form
!
Specify the class(es) of restriction to include in each
class of restriction group number.
5. Route Assignment form
!
For each route number, specify the trunk group
number, class of restriction group number, and digit
modification number.
!
(Optional) In the Digits Before Outpulsing field for
each route number, specify the number of digits to
process before overlap outpulsing begins.
!
(Optional) Assign emergency routes by entering “E”
in the Route Type field. This must be a DPNSS route.
!
(Optional) Assign XNET routes by entering the
appropriate trunk group number in the XNET Trunk
Group Number field.
71
Programming
Create a call progress tone detection plan (An
Advanced Tone Detector card is required).
Technician’s Handbook
6. (Optional - Advanced ARS only) Day and Time Zone
Assignment form
!
Create a day and time zone plan.
7. (Optional - Advanced ARS only) Route Plan Assignment
form
!
Create a route plan.
8. (Optional) Route List Assignment form
!
For each route list number, specify routes in order
from least expensive to most expensive.
!
(Optional) Apply warning tone to more expensive
routes.
9. Automatic Route Selection Assignment form
72
!
In the Leading Digits field, specify which digits must
be dialed to access the information in this form.
!
In the COR Group field, specify the class of
restriction group number that does NOT have access
to the ARS leading digits.
!
In the Digits Dialed field, specify the digits to dial to
access routing information.
!
Complete the Number of Digits to Follow field.
!
In the Termination field, specify one of the following:
—
the type “Route” and a route number
—
the type “List” and a route list number
—
the type “Plan” and a route plan number (for
Advanced ARS only).
Programming
Hint:
To bar a station from all outgoing trunks
1. Class of Restriction Group Assignment form
!
Assign the class of restriciton of the station to a COR
Group.
2. Digit Modification Assignment form
Create an instance of the Digit Modification
Assignment form that has the trunk access code
(normally “9”) in the Leading Digits field.
!
Leave the remaining fields blank.
3. Route Assignment form
!
Enter the station's class of restriction Group number
in the COR Group Number field.
73
Programming
!
Technician’s Handbook
74
Chapter 4
Maintenance Commands
75
Technician’s Handbook
76
Maintenance Commands
Basic Commands
Accessing Desktop Mode
DESktop
Returns the screen to desktop mode.
Logging Out
DESktop [Return] [Esc] 1
Logs you out of the system.
Selecting a Different Language
LANguage Select <language> SETS DEFAULT
FROM *.<catalog>
Changes the default language for SUPERSET display
telephones and attendant consoles. The languages
available are Dutch, English, French, German, Italian,
LA_Spanish, Eu_Spanish, BR_Portuguese,
PT_Portuguese, and Romanian. The status of the auxiliary
languages is not changed.
HELp
Displays a list of maintenance commands. Press [Esc] Q or
press [PF4] to exit.
HELp <command>
Provides an explanation of the specified maintenance
command. Press [Esc] Q or press [PF4] to exit.
77
Maintenance
Commands
Getting Help
Technician’s Handbook
Changing the Password
CHange Password
Changes the password of the logged-in user.
Resetting the Password for a Lower Level
RESEt Password
Resets the password of a lower level (for example, from
Installer level you can reset the Maint1 level password).
Resetting Usernames
RESEt Username <user>
(Introduced in P07.2.1)
Allows a System-level user to replace an existing System,
Installer, Maint1, or Maint2-level username with a new
username.
Displaying Usernames
DISPlay Usernames
(Introduced in P07.2.1)
Allows a System-level user to display a list of all valid
usernames.
Switching from CDE or Desktop to Maintenance Mode
MAintenance
Changes from CDE mode or desktop mode to maintenance
mode.
78
Maintenance Commands
Stepping Back through Commands
[Esc] [Ctrl] J
Displays the previously issued command in the command
line. You can display the last three commands.
Displaying the System Software Revision
WHere
Displays the software revision of the system.
Displaying the System Software Versions
VErsion
Displays the software version of each processor in the
system. You can also apply this command to particular
processors (for example, VE MAIN, VE PERIPH, etc.).
Changing or Reading the System Time
TIme <hh:mm:ss> AM/PM
Sets the system time. Example entry:
TI 11:30:45 AM
Changing or Reading the System Date
DATE <yyyy-mmm-dd>
Sets the system date. Example entry:
DATE 1999-AUG-04
You can also enter the time following the date. You can read
the system date by entering the DATE command without any
qualifiers.
79
Maintenance
Commands
You can also enter the time in 24-hour format by omitting the
AM or PM. You can read the system time by entering the
TIME command without any qualifiers.
Technician’s Handbook
Change Tenant Day/Night Service
CP Service <day>
CP Service <night1>
CP Service <night2>
To set the default (tenant group 1) to the specified day/night
service.
Changing the Baud Rate
BAUd <NNNN>
Sets the baud rate of the maintenance port. Available baud
rates are 300, 600, 1200, 2400, 3600, 4800, or 9600.
BAUd <NNNN> <port name>
Sets the baud rate of the specified port.
Change the baud rate of the system’s maintenance port.
Then, change the baud rate of the maintenance terminal.
Press [Ctrl] W to refresh the terminal screen.
Changing the Parity of a Console Port or DNIC Port
PARIty <XYZ> <port name>
Changes the parity of a console port or DNIC system port. X
= number of bits (7 or 8); Y = Parity (Odd, Even or None); Z
= number of stop bits (1 or 2). Example entry:
PARI 8E1 SS7PRI
This command will not work on port LPR2.
Refreshing the Terminal Screen
[Ctrl] W
If the screen doesn’t refresh, press [Ctrl] Q and [Ctrl] C.
Then enter [Ctrl] W again.
80
Maintenance Commands
Cancelling a Maintenance Command
[Ctrl] C
Terminates testing. It does not cancel all maintenance
commands.
Printing to LPR3
1. FOrmprint <form name> /ALL /PORT LPR3
2. ENable PrInt /Nonqueued
Prints all instances of each specified form to the printer at
port LPR3 (line 1 can be repeated using different form name
parameters). Press [Ctrl] C to terminate printing.
1. PRInt <filename> /PORT LPR3
2. ENable PrInt /Nonqueued
Prints the specified file to the printer at port LPR3 (line 1 can
be repeated using different filename parameters). Press
[Ctrl] C to terminate printing.
Printing Log Files to a Local Printer
PRInt <filename> /PORT <port name>
Prints the session log file to the specified printer port.
FOrmprint <form name>
Prints a single instance form to the programmed system
port.
FOrmprint <form name> /PORT <portname>
Prints a single instance form to the specified port.
FOrmprint <form name> /INSTANCE n /PORT
<port name>
81
Maintenance
Commands
Printing a CDE Form
Technician’s Handbook
Prints instance n of the specified multiple instance form to
the specified printer port.
FOrmprint <form name> /ALL /PORT <port name>
Prints all instances of the specified form to the specified
printer.
82
Maintenance Commands
Switching the Terminal from Screen Mode to Print Mode
ENable Print /Nonqueued
Switches the terminal from screen mode to print mode. Any
print jobs queued to LPR3 will print from the maintenance
terminal printer port. The terminal screen clears, and normal
operation does not resume until all queued jobs are printed.
To halt the printing and return to screen mode, press
[Ctrl] C.
Checking the Print Queue
SHow Print ALL
Displays the print requests queued against the default
printer.
SHow Print <printer port name>
Displays the print requests queued against the specified
printer.
Cancelling a Print Job
CANcel Print ALL
Cancels all print jobs on the default printer.
Cancels the specified print job on the default printer port.
CANcel Print <job number> /PORT <port name>
Cancels the specified print job on the specified printer port.
83
Maintenance
Commands
CANcel Print <job number>
Technician’s Handbook
Assigning a New Default Printer
MYprinter <printer name>
Assigns a new default printer to the maintenance terminal.
Creating a Catalog
FILe CReate <pathname>.<catalog name>
CATalog
Example entry: FIL CR ∗.DATASAVE.JAN1995 CAT
Displaying Catalogs
CATalog Info <pathname> FULL
Displays all catalogs for the specified pathname.
84
Maintenance Commands
Troubleshooting Commands
Starting, Ending, and Printing a Session Log
SESsion Start
Begins a session log and stores it in
∗.maintenance.session_log
SESsion End
Ends a session log and stores it in
∗.maintenance.session_log.
PRInt ∗.MAINTENANCE.SESSION_LOG /PORT
<printer port>
Prints the log session at the specified printer port.
Showing Alarms
ALarms
Shows alarm information for all alarm categories.
SHow STatus ALarms
Shows alarm categories with raised alarms.
SHow FAults ALarms
Lists the faults causing the alarms in all alarm categories.
SHow FAults <alarm category>
Lists the faults causing the alarms in the specified alarm
category.
85
Maintenance
Commands
Showing Faults
Technician’s Handbook
Setting Alarm Thresholds
SET Threshold <alarm category> <x> <y> <z>
Defines the thresholds for a minor, major, or critical alarm
where x, y, and z are the minor, major, and critical alarm
thresholds.
Example entry: SET T atd channels 0 50 100
To blank an entry for x, y, or z, enter NIL.
Displaying the State of a Circuit
STate <plid>
Gives the state of the circuits at the specified PLID.
Displaying the State of Line Appearances
STate MLS <plid> <circuit> <line appearance
number>
Gives the state of the specified line appearance on a
multiline set.
Displaying the Total Number of System Resources
SYstem Totals
Displays the total numbers of programmed trunks, lines,
stations, and attendants.
86
Maintenance Commands
Busying Out a Card, Circuit, or Channel for Testing
BUsy <plid>
If the circuit is busy when you issue this command (indicated
by "has an owner"), you have three options:
QUIT: leaves the circuit unbusied.
FORCE: cuts off the call in process and forces the circuit into
manbusy.
COURTESY DOWN: waits for the call to end before placing
the circuit into manbusy.
To return a busied circuit to service, enter RTS <plid>.
An extension parameter can also be used (BU EX
<extension number>). System repsonse is the same
whether an extension or a PLID is used.
Returning a Busy Circuit or Trunk to Service
RTS <plid>
or
RTS EX <extension number>
or
Maintenance
Commands
RTS TRUNK GROUP <group number> ALL
Removing a Courtesy Down Request
RCD <plid>
Removes a previous request to busy a peripheral circuit at
the specified PLID. An extension parameter can also be
used (RCD EX <extension number>). System response is
the same whether an extension or PLID is used.
87
Technician’s Handbook
Testing Circuits
TEst <plid>
Tests the circuit(s) at the specified PLID.
TEst EXT <extension number>
Tests the circuit(s) at the specified extension. System
response is the same whether an extension or PLID is used.
TEst <plid> Continuous
Repeatedly tests the circuit(s) at the specified PLID. Enter
[Ctrl] c to terminate testing.
TEst <plid> SEize
Tests whether the facility at the far end of a trunk is
responding to a near-end attempt to seize the trunk.
TEst Trunk Group <group number>
Tests the trunks in the specified trunk group.
TEst <plid> Until Fail
Repeatedly tests the circuit(s) at the specified PLID until
failure occurs. Enter [Ctrl] C to terminate testing.
SHow Seize TEst
Shows the status of seize testing for out-of-service trunks.
DISable Seize TEst
Disables seize testing for out-of-service trunks.
88
Maintenance Commands
Displaying the Call Path of a Set
RESOurces <plid>
Indicates the call path and destination device of the set at
the specified PLID.
RESOurces VIRTUAL <plid>
Used to specify MSDN/DPNSS virtual channels.
RESOurces XNET <trunk>
Used to display a device type of “XNET Trunk” representing
a trunk, set, or console used in an XNET call.
Reading Maintenance Logs
Four logs are available: Maintenance, Software, SMDR, and
Hotel/Motel.
LOGSys Read <log name> NEWest/OLDest <#>
Displays the specified number of newest or oldest entries in
the specified log.
LOGSys Read <log name> NEW/OLD <#> MAtch
"xxxx"
Searches the specified number of newest or oldest entries in
the log for the string xxxx.
Maintenance
Commands
LOGSys Read <log name> ALL MAtch "xxxx"
Searches all log entries in the specified log for those
containing the string xxxx.
LOGSys Read OTHER <log name> ALL MAtch
"xxxx"
Searches all log entries in the specified log on the other
plane for those containing the specified string.
89
Technician’s Handbook
Cancelling a Logs Read Command
LOGSys CAncel
Cancels the previously entered Logs Read command.
Printing Maintenance Logs
Four logs are available: Maintenance, Software, SMDR, and
Hotel/Motel.
LOGSys PRInt <log name>
Prints all previously unprinted entries in the specified log.
LOGSys PRInt <log name> ALL
Prints all previously printed and unprinted entries in the
specified log.
Deleting Log Entries
LOGSys PURge <log name>
Deletes all entries from the specified log. Once deleted,
entries cannot be recovered.
Checking the Log Parameters
LOGSys Attributes <log name>
Displays the operating parameters of the system logs.
Setting the Size of the SMDR Log File
LOGSys Size <SMDR> FILE <entry count>
Sets the size of the SMDR buffer file. The default entry count
is 20000. The maximum entry count is 75000.
90
Maintenance Commands
Main Control Commands
Switching Activity (Redundant Systems Only)
ACTivity FREeze ON/OFF
(Introduced in P02.3.2)
Freezes activity switching between planes. You cannot use
this command to disable Activity Freeze if it was enabled
from the control panel. You also cannot use the control panel
to disable Activity Freeze if it was enabled by this command.
ACTivity FREeze STATUS
(Introduced in P02.3.2)
Displays activity freeze status.
ACTivity Switch <plid>
Makes the redundant control card at the specified PLID
active.
ACTivity Switch Force
Forces an activity switch on a partitioned system.
Scheduling an Activity Switch (Redundant Systems
Only)
<DAILY or day of week> <hh:mm:ss>
<MONTHLY> <week # [1-4]> <day> <hh:mm:ss>
<YEARLY>
<month> <week # [1-4]> <day> <hh:mm:ss>
Schedules an activity switch on the specified day at the
specified time.
91
Maintenance
Commands
ACTivity Switch Schedule
Technician’s Handbook
ACTivity Switch Display
Displays the activity switch schedule.
ACTivity Switch ON/OFF
Turns automatic activity switching on or off.
Turning Background Diagnostics On/Off
BACkground ON/OFF
Turns background diagnostics on or off.
BACkground ON/OFF <category>
Turns background diagnostics on or off for the specified
category.
BACkground Status
Displays which diagnostics are off and which are on.
Displaying the Card Configuration
CONFiguration Long <plid>
Displays the programmed and installed cards at the
specified PLID.
Identifying System Resource Shortages
CONGestion
Lists system resource shortages.
Identifying and Downloading Firmware
FIRmware ALL
Lists the firmware in all installed cards.
92
Maintenance Commands
FIRmware ALLEprom
Lists the firmware in all cards that are equipped with EPROM
software.
FIRmware PLID <plid>
Lists the firmware for the card at the specified PLID.
FIRmware Cardtype <card type>
Lists the firmware for all cards of the specified type.
FIRmware PAnel
Lists the firmware in the control panel and mass storage
devices.
Using the FIRM KILL command:
!
Use with caution. This command updates the
firmware on all devices that support firmware
download. The device will be out of service until the
firmware update is complete.
!
Issue the FIRM KILL command to fewer ports at a
time to diminish process times and avoid the
possibility of overlap.
!
Before using the FIRM KILL command:
!
Set ACTivity FREeze OFF and BACkground ON
DNI after the firmware upgrade is complete.
FIRmware KILL ALL
Use with caution. This command updates the firmware on all
devices that support firmware download. All devices will be
out of service until the firmware update is complete.
93
Maintenance
Commands
- Set ACTivity FREeze ON to disable Activity
Switch/Programmed Reboot
- Issue the BACkground OFF DNI command to
disable self diagnostics for the DNI ports only.
Technician’s Handbook
FIRmware KILL PLID <plid>
Updates the firmware on all devices at the specified PLID
(that support firmware download).
FIRmware KILL SET <set type>
Updates the firmware on all devices of a specific type (that
support firmware download). For example, FIRmware KILL
SET 4025.
Identifying Cards
PROM <plid>
Gives the card type, revision number, and time and place of
manufacture for the card at the specified PLID.
Checking for Mass Storage Subsystem Errors
MSSstats
Lists the hard and soft errors against the mass storage
devices.
Loading Software into a Card’s Processor
LOAd <plid>
Loads software into the processor in the specified card slot.
LOAd Controllers
(Introduced in P17.6.4)
Loads software into all peripheral processors, digital service
units, DNI cards, and attendant consoles.
94
Maintenance Commands
Testing PCM Links
PCM STATUS <Tx or Rx> <link number>
Shows the status of a PCM circuit switch link.
PCM TEst Both <link>
Tests all channels on a PCM circuit switch link. The system
should report zero faults.
PCM TOtals
Reports on all circuit switch links in the system. The system
should report zero faults.
Scheduling a System Reboot (Non-redundant Systems)
PROGrammed Reboot SCHedule
<DAILY or day of week> <hh:mm:ss>
<MONTHLY> <week # [1-4]> <day> <hh:mm:ss>
<YEARLY>
<month> <week # [1-4]> <day> <hh:mm:ss>
Schedules a software controlled system reboot on the
specified day at the specified time.
A software controlled reboot takes place at the next
occurrence of the specified time. This default setting will only
reboot if there is memory fragmentation. To force a system
reboot at a scheduled time, use the previous command.
PROGrammed Reboot Display
Displays the reboot schedule.
PROGrammed Reboot ON/OFF
Turns automatic system reboot on or off.
95
Maintenance
Commands
PROGrammed Reboot Memory Daily <hh:mm:ss>
Technician’s Handbook
WARNING: A Non-redundant switch is never recommended
for use where the need for constant
telecommunications availability is required.
Because of the time it takes to complete an
SX-2000 Non-redundant system reboot, and the
absence of 911 functionality during this time, Mitel
does not recommend a non-redundant system for
mission critical sites such as hospitals, prisons,
and police and fire stations. Certain hospitality
and university residence sites, where 24 hour
operations are a requirement, should always be
serviced by an SX-2000 redundant system. For
sites that must be protected against system
outages resulting from software, hardware or
regularly scheduled maintenance activities,
redundancy on the SX-2000 is recommended.
Displaying the Status of Communication Paths
MEssage MATE
Displays the status of message links between redundant
processors.
MEssage SUB
Displays the status of message links between the main
control, and peripheral and DSU processors. All links should
be open.
MEssage R
Displays the status of remote message links.
Collecting Traffic Data
Traffic data collection is set up using the Traffic Options
Assignment form.
TRAFfic STAtus
Gives the current status of traffic data collection.
96
Maintenance Commands
TRAFfic Files
Lists the traffic files stored in the system.
TRAFfic Print <mmm-dd hh:mm:ss>
Prints the specified file(s) for the specified month, day, hour,
minutes and seconds. The date and time qualifiers are
optional.
TRAFfic Delete <mmm-dd hh:mm>
Deletes the traffic file(s) for the specified month, day, hour
and minutes. The date and time qualifiers are optional.
TRAFfic STOp <mmm-dd hh:mm>
Ends the current traffic data collection period and generates
a report.
Displaying Traffic Files
CATalog INFO *.traffic
Dispalys a list of the traffic files.
Example display:
*.TRAFFIC.2001JAN040631
*.TRAFFIC.2001JAN040701
Maintenance
Commands
To display the contents of a traffic file, enter the type
command and the file name.
Example entry:
type *.TRAFFIC.2001JAN040631
97
Technician’s Handbook
Database Commands
Checking the Database
DBMs CHeck FULL
Gives the number of database errors. There should always
be zero view errors and zero table errors. If errors are
indicated, see Fixing Database Errors on page 128.
DBMs CHeck KILL
Terminates a DBMS CHECK in progress.
DBMs CHeck ON/OFF
Turns automatic database checking on or off. The default is
5:00 a.m. daily.
DBMs STATus
Gives the status of the DBMS Flag (indicated by
"DBMS_INITIALIZED is on/off"). See also DBMs FLag OFF
on page 99. The normal status is “DBMS_INITIALIZED is
ON”.
DBMs Query
Displays the dimension number, number of cabinets, and
system features.
DBMs Check Time <hh>
Sets the automatic database checking to occur at the
specified hour. Enter the hour in a 24-hour clock format.
98
Maintenance Commands
Saving and Restoring the Database
DBMs SAve
Saves the database to ∗.REDUNDB catalog on the hard
disk.
DBMs SAve ∗.<volume name of RSD>
Saves the database to RSD. First mount the RSD by
entering VOlume Mount RSD.
DBMs FLag OFF
Use this command with caution. This command blanks
the database on the next system reload. It must precede a
DATA Restore. See also DBMs STATus on page 98.
DBMs Download ∗.<volume name>
Copies the database from the RSD into RAM. Mount the
RSD by entering VOlume Mount RSD.
DATA SAve
Copies the entire database from system memory to the
catalog ∗.DR.CONFIG on the hard drive.
DATA SAve ∗.<volume name>
DATA Restore
Restores to memory the database that was saved to the
catalog ∗.DR.CONFIG on the hard drive.
DATA Restore ∗.<volume name of RSD>
Restores to memory a database that was saved to an RSD
by using the DATA Save command. Mount the RSD by
entering VOlume Mount RSD.
99
Maintenance
Commands
Copies the entire database from system memory to a RSD.
First mount the RSD by entering VOlume Mount RSD.
Technician’s Handbook
DATA Query
Displays details about the database saved in the catalog
∗.DR.CONFIG on the hard drive.
DATA Query ∗.<volume name of RSD>
Displays information on the database that is saved on an
RSD.
DATA CONVert ∗.<volume name of RSD>
Restores to memory a database that was saved to a catalog
on an RSD by using the DATA SAVE command. This
command is applicable if the system is running software
earlier than P02.3.2. Mount the RSD by entering VOlume
Mount RSD.
RSD Copy from Mitel Support Web Site
RSD COPY TO NET <filename>
To copy an RSD to a network computer.
RSD COPY FROM NET <filename>
To copy the file from the network computer onto the RSD.
RSD VERIFY NET <filename>
To confirm that no data errors were written.
RSD CANCEL
To terminate an RSD command.
Backing Up and Restoring Message Center Messages
MSGCtr Backup ∗.<volume name of RSD>
Saves message center information to RSD.
MSGCtr Restore ∗.<volume name of RSD>
Restores message center information from RSD to the hard
disk.
100
Maintenance Commands
Redundant File System Commands
Partitioning and Joining
PARTition
Isolates redundant processors and disables the redundant
file system (use this command only when upgrading
software). Enter this command first from the active plane,
then from the inactive plane.
JOin
Re-establishes communication between partitioned
redundant processors. Enter this command first from the
inactive plane and then from the active plane.
Disabling and Enabling File Redundancy
FILe DISable REDundancy
Stops the active controller from controlling the database on
the inactive plane’s hard drive. Use this command only when
loading system software.
FILe ENable REDundancy
FILe STatus REDundancy
Indicates whether databases on both drives are identical (in
synch), being made identical (out of synch), or isolated and
different (isolated).
101
Maintenance
Commands
Gives the active controller control of the databases on both
hard drives. The active controller copies the entire database
to the inactive plane.
Technician’s Handbook
Which Main Controller is Active?
WHere
Indicates which main controller the maintenance terminal is
connected to, and whether the main controller is active or
inactive. An asterisk at the end of the first line in the display
response indicates that the controller is partitioned.
Displaying Information on a Volume
VOlume Info <volume name>
Displays the name and space allocation of the mounted
volume.
Mounting and Dismounting a Volume
VOlume Mount <device>
Makes the volume on the RSD accessible to the file system
and displays its name.
VOlume DISMount <volume name>
Use this command with caution. Takes the specified
volume off-line. If you dismount SYSUSER, a restart or
reload is necessary to mount the hard disk again. You
should dismount SYSUSER when upgrading the system
software or when powering down the system.
Backing Up and Restoring a Volume
VOlume Backup <volume name> ON <device>
Use this command with caution. Copies the contents of
the specified volume (for example, SYSUSER) to the
specified device (for example, RSD). If you specify
SYSUSER as the volume name, you must reload the system
to mount the hard disk again.
102
Maintenance Commands
VOlume Restore <volume name> FROM <device>
Restores the contents of the volume (for example,
SYSUSER) from the device (for example, RSD).
VOlume Set SYSUSER READ ONLY
Entering this command makes the plane’s hard disk
read-only. Use this command only on the active plane to
protect the contents of the inactive plane’s hard drive when
copying it to the active plane’s hard drive.
VOlume Restore SYSUSER FROM OTHER
Copies the contents of the mate plane’s hard disk to this
plane’s hard disk. Enter the VOLUME SET SYSUSER
READ ONLY command on the active plane before entering
the VOLUME RESTORE SYSUSER FROM OTHER
command on the inactive plane.
VOlume Set SYSUSER READ WRITE
Restores read and write access to the hard disk after a
VOLUME SET SYSUSER READ ONLY.
Enabling and Disabling Access to a Volume
VOlume DISAble <volume name>
VOlume Enable <volume name>
Re-enables access to the volume after a VOLUME
DISABLE.
103
Maintenance
Commands
Use this command with caution. Stops the system from
accessing the specified volume (for example, SYSUSER).
Technician’s Handbook
Formatting a Volume
VOlume Format <RSD> <volume name> RES
SCRatch
Erases, formats, and renames the device to the specified
volume name. Use the SCRatch qualifier only when
changing from a previously formatted older file system.
Always use the SCRatch qualifier when formatting the hard
disk.
VOlume Format <RSD> <volume name> RES
Erases, formats, and renames the device to the specified
volume name. Use this command to format an RSD to be
used for backup purposes.
VOlume Format <RSD> <volume name>
Erases, formats, and renames the device to the specified
volume name. Use this command to format an RSD to be
used for a DATA SAVE.
VOlume Format DISK SYSUSER REDundancy
ONLY
Erases and formats the redundant file system only.
104
Maintenance Commands
Peripheral Devices Commands
Locating an Extension or Trunk
LOCate EXtension <extension number>
Gives the PLID of the set for the specified extension number.
LOCate Trunk <trunk number>
Gives the PLID of the specified trunk.
Locating Where a Number is Used
LOCate NUMber <number>
Indicates where a number is used (what purpose it serves).
Locating a Tenant
LOCATE TENANT <number>
Displays a specified tenant group.
LOCATE TENANT
Displays all tenant groups.
LOCate FEature EXtension <extension number>
Lists which features are active at the specified extension
number.
LOCate FEature PLID <plid>
Lists which features are active on the set at the specified
PLID.
105
Maintenance
Commands
Listing the Active Features for an Extension or PLID
Technician’s Handbook
Finding the Directory Number of a Set or Trunk
LOCate PLID <plid>
Gives the directory number of the set or trunk at the
specified PLID.
Finding Free Directory Numbers or PLIDs
LOCate FIRST FREE PLID <card type> <plid
start> TO <plid end>
(Introduced in P07.2.1)
Identifies the first available PLID in a range.
Note: Valid <card type> qualifiers are: ONSLINE, OPSLINE,
CEPT, DS1, DNILINE, E_AND_M, SCDCTRUNK,
COVLINE, DATASTATION, AC15, DIGITALLINE, LS/GS,
DID2, LOOPDID, DID3, or ANYCARDTYPE.
LOCate ALL FREE PLID <card type> <plid start>
TO <plid end>
(Introduced in P07.2.1)
Identifies all available PLIDs in a range.
LOCate FIRST FREE DN <dn start> TO <dn end>
EXT
(Introduced in P07.2.1)
Identifies the first available unassigned directory number in
a range.
Note: The EXT qualifier at the end of the command string
will cause directory number searches to include those DNs
containing * and/or # characters.
LOCate ALL FREE DN <dn start> TO <dn end>
EXT
(Introduced in P07.2.1)
Identifies all available unassigned directory numbers in a
range.
106
Maintenance Commands
Moving, Adding, and Swapping Telephone Users
MOVe User <X> TO <Y>
Moves name and attributes from extension number X to
extension number Y. Extension numbers (X and Y) remain
with the sets. See Moving a Telephone User on page 61.
MOVe ADD <“lastname, firstname”> TO
<extension number>
Adds a name to a number that exists in the telephone
directory.
MOVe Swap <X> WITH <Y>
Swaps names, numbers, and attributes between the sets at
the specified extension numbers X and Y. See Swapping
Users’ Telephones on page 62.
Deleting Telephone Users
MOVe DELete <“lastname, firstname”> FROM
<extension number>
Deletes the name associated with the extension number
from the telephone directory.
Changing an Extension Number
Maintenance
Commands
MOVe RENumber <old number> TO <new
number>
Changes an existing extension number.
107
Technician’s Handbook
Digital Trunk Commands
Displaying the Status of a Digital Link
DTstat Read <plid>
Gives the status of a digital link that connects to a DS1 or
CEPT Formatter card.
Note: <plid> = <cab> <shelf> <slot> <hybrid or link>.
DTstat Read APNss Group <number>
Gives the status of an APNSS link that is controlled by a DS1
or CEPT Formatter card.
DTstat Clear <plid>
Clears performance statistics for a specified digital link.
Note: <plid> = <cab> <shelf> <slot> <hybrid or link>.
Testing Digital Trunks
BUsy APNss Group <#> Traffic/Signalling/All
Places the circuits in the specified APNSS group into busy
state.
BUsy <plid of CEPT or DS1 Formatter card>
<hybrid>
Places the specified CEPT or DS1 hybrid into busy state.
TEst APNss Group <#> Traffic/Signalling/All
Tests the trunks in the specified APNSS group.
TEst <plid of CEPT or DS1 Formatter card>
<hybrid or link>
Tests a single hybrid (link on a DS1 or CEPT Formatter
card).
108
Maintenance Commands
RTS <plid of CEPT or DS1 Formatter card>
<hybrid or link>
Returns busied circuits to service in the specified trunk
group.
RTS APNss Group <#> Traffic/Virtual/ALL
Returns busied APNSS group circuits to service.
Synchronizing the Active Clock Source
NEtsync SEtsource <source #>
Forces the system to synchronize its clock with the one
supplied by the specified source number.
NEtsync SEtsource FREERUN
Stops the system from synchronizing to any of the external
sources.
NEtsync SEtsource AUTO
Allows the system to choose the most reliable sync source.
Displaying Synchronization Information
NEtsync STate
NEtsync SUmmary <shelf # of synch source>
Gives a performance history of the sync sources that the
system has used. Enter this command from the active plane.
For the shelf # of synch source parameter, enter 1 if plane A
is active and 2 if plane B is active.
109
Maintenance
Commands
Lists the state of the sync source.
Technician’s Handbook
NEtsync SUmmary <shelf> LAST <number of
hours>
Gives a performance history of the sync source that the
system has used over the last number of specified hours.
For the shelf parameter, enter 1 if plane A is active and 2 if
plane B is active.
110
Maintenance Commands
DS1/CEPT Formatter I Card (MC263CA
and MC264CA) Communications
Use the following VT100 terminal emulation settings and
commands when communicating with a DS1/T1 Formatter I
card (MC263CA) or CEPT Formatter I card (MC264CA).
Settings
Use the following VT100 terminal emulation settings:
Baud rate: 38,400 bps
Databits: 8
Parity: N
Stop bits: 1
No flow control.
Commands
Use the following commands:
sig cas
Sets the signaling to CAS (default T1).
Maintenance
Commands
sig dpnss
Sets the signaling to DPNSS (default CEPT).
+dchan-inv (T1 only)
Sets D-channel inversion to ON (default).
-dchan-inv (T1 only)
Sets D-channel inversion to OFF.
111
Technician’s Handbook
line len # (T1 only)
Sets the line length for T1 where “#” is replaced with the
following: 1 = 0-133, 2 = 134-266, 3 = 267-399, 4 = 400-533,
5 = 534-655.
dis opt
Displays the DS1/CEPT options settings.
force dl
Deletes the datetag file and resets the card.
reset
Resets the card which enables changes in the parameter
settings.
112
Chapter 5
Troubleshooting and
Repair
113
Technician’s Handbook
114
Troubleshooting and Repair
Identifying Faults
The Bootstrap Sequence
Table 24: System Bootstrap Sequence
Normal Numeric Error Display on Main
Display on Main
Controller Card
Controller Card
Sequence
Notes
The numeric display
Main Controller
briefly flashes EE followed self test
by the test code number.
These tests are run out of the
EPROM on the main controller
card.
B0 - RSD access
B1 - disk access
(These codes are
displayed briefly as
the system accesses
the RSD drive, and
the disk drives.)
Any Bx codes other than
B0 or B1 indicate errors.
OR
If B1 and/or B0 are
displayed for several
minutes, an error
condition exists.
It takes the main controller only a
few seconds to obtain the
MCINIT test from the RSD or
hard disk. It begins doing the
tests as soon as it gets them.
Check that the LEDs on the hard
drives and RSD drive are
flashing. If the LEDs are not
flashing at this stage, the mass
storage subsystem is faulty.
Test code appears
for each test
The numeric display
Test MCINT
briefly flashes EE followed control section
by an error code.
Test results are displayed on the
maintenance terminal screen.
The main controller sends these
results to the maintenance
terminal at 9600 baud, 8N1.
Fast count
Same as above.
Load operating
software
The main controller is
transferring its operating system
from hard disk to RAM.
Sporadic
Same as above.
Initialize
operating
system (OSInit)
The main controller sends these
results to the maintenance
terminal at 9600 baud, 8N1.
Slow steady flashing Same as above.
Normal
operation on
main controller
The main controller begins
communicating with the
maintenance terminal at the last
saved baud rate. The desktop
display appears, allowing you to
start a session. The flashing
numbers on the processor
indicate the number of messages
passing between it and the other
processors on the system.
Fast count on
subsystem
processor. High
message numbers
flashing on main
processor.
Loading
subsystem
processors
The main controller transfers the
subsystem processor software
loads from the hard disk to the
subsystem processors
(Peripheral Switch Controller
cards, DSU cards, DNI line
cards, and attendant consoles).
Same as above.
Get MCINIT
from disk or
RSD
115
Troubleshooting
Test code appears
for each self test
Technician’s Handbook
Flowchart 1: Getting Started
Flowchart 1:
Start
Are
all system LEDs on
the main control
cabinet out?
Yes
Power subsystem is faulty.
Check the AC power source.
No
Is the
maintenance terminal
operating? (Ensure
maintenance terminal is
connected to the faulty
plane).
Yes
No
Is the operating system on the faulty plane intact?
Check the faulty plane’s MC card numeric display:
No
A
116
Yes
YES: slow, steady flashing (1 second flash rate).
NO: any other state (e.g., counting, alternating
between two numbers, on steady or off steady).
Flowchart 6:
Maintenance terminal
troubleshooting
B
Troubleshooting and Repair
Flowchart 1: Continued
A
No
B
Is the
system in the
process of a normal
boot?
Yes
Unsure?
Flowchart 5:
The system bootstrap
sequence
Wait until the system
finishes booting. If a minor,
major, or critical alarm is
present, start this flowchart
again.
Yes
Flowchart 3:
An alarm is present
Troubleshooting
Flowchart 2:
System is not booting up
Is a minor,
major or critical alarm
LED on?
No
Flowchart 4:
Correcting set/dataset
problems
117
Technician’s Handbook
Flowchart 2: The System is Not Booting Up
Flowchart 2:
System is not
booting up
On redundant systems, set
ACTIVITY FREEZE to “on”.
Is the main
controller card
numeric display
flashing EE followed by
an error code (2-digit
number)?
Yes
Reload the software (hold down the
PANEL ENABLE button and press
the RESET button of the affected
plane). If the problem persists,
replace the main controller card.
See Replacing a Main Controller
Card on page 147.
No
Is the
main controller card
numeric display
continuously alternating
codes B0 and B1?
No
C
118
Yes
Mass storage system is faulty.
Check for faulty connections to the
hard disks.
Power off the plane and then power
it on again.
Next, try loading the system
software from RSD. If you can’t load
the software from RSD, see
Removing and Replacing a Faulty
Hard Disk on page 143.
Troubleshooting and Repair
Flowchart 2: Continued
C
Are any of the
peripheral control
complex card numeric
displays flashing EE
followed by an error
code?
Yes
No
No
Yes
Flowchart 3:
An alarm is present
Troubleshooting
complete.
119
Troubleshooting
Is a system
alarm present?
Check for bent pins on the peripheral
switch controller card connector.
Check for a faulty Fiber Interface
Module (FIM).
Ensure ACTIVITY FREEZE is on.
Reload the peripheral switch controller
card by using the LOAD
CONTROLLERS command. If the fault
persists, reload the software into the
main controller card. If the fault persists,
replace the peripheral switch controller
card. See Replacing a Peripheral
Switch Controller (PSC) Card on page
148.
Technician’s Handbook
Flowchart 3: An Alarm is Present
Flowchart 3:
An alarm is present.
Enter this command:
SHOW STATUS ALARMS
The terminal displays the alarm category.
Enter:
SHOW FAULTS <alarm category>
The system displays the alarm category and
identifies the faulty card or device.
Record the name and the physical location
identifier (PLID) of the faulty card or device.
Enter:
STATE <PLID> of the faulty card or device.
Enter:
TEST <PLID> of the faulty card or device.
Replace the faulty card or device. See
Replacing Circuit Cards on page 146 and
Recovering from a Corrupted Hard Disk on
page 140. See also, the SX-2000 Install
Upgrades and FRUs (Field Replaceable
Units) section of the Technical Documentation
CD-ROM.
120
Troubleshooting and Repair
Flowchart 4: Correcting Set/Dataset Problems
Flowchart 4:
Correcting set/dataset
problems
Enter:
LOC FEAT EXT <ext. number>.
The system displays the active
features for that extension.
Is the fault
corrected?
Ensure that valid features,
such as do not disturb or call
forwarding, are not causing the
set or dataset to appear faulty.
Yes
Troubleshooting complete.
Troubleshooting
No
Swap the set/dataset with a known working
set/dataset (of the same model).
Is the fault
corrected?
Yes
Return faulty set/dataset
for repair.
No
Enter:
BUSY <PLID> of the card for the
set/dataset. Select COURTESY DOWN.
D
121
Technician’s Handbook
Flowchart 4: Continued
D
Enter:
STATE <PLID> of the card.
Are all circuits
busy?
No
Wait until all
circuits are in the
busy state.
Yes
Swap the card with a known working
card. Enter RTS <PLID> to return the
circuits to service.
Is the fault
corrected?
Yes
No
Check the cable and cable connections
between the set and the line card.
See the SX-2000 Peripheral Troubleshooting
Procedures section of the Technical
Documentation CD-ROM for further possible
corrective action.
122
Return faulty
card for repair.
Troubleshooting and Repair
Flowchart 5: The Bootstrap Sequence
Flowchart 5:
The system bootstrap
sequence
See The Bootstrap Sequence on page 115
to identify whether the system is in the
process of a normal bootstrap sequence.
After determining the status of the bootstrap
sequence, proceed from this point in the
flowchart.
No
Flowchart 2:
Troubleshooting
Is the system
booting properly?
System is not booting up
Yes
Wait for the system to
finish booting.
E
123
Technician’s Handbook
Flowchart 5: Continued
E
Do you have a
redundant
system?
No
Yes
Is a system
alarm present?
Yes
Enter:
FILE STATUS REDUN
first from the active plane,
then from the inactive plane.
Troubleshooting
complete.
Interpret the system
response using Table 25 on
page 125.
Flowchart 3:
An alarm is present
F
124
No
Troubleshooting and Repair
Flowchart 5: Continued
F
Table 25: Status of Redundant File System
FILE STAT FILE STAT
REDUN on REDUN on
the active the inactive
Plane
Plane
ISOLATED
Interpretation
ISOLATED The system is likely partitioned.
You can check this status by
entering the WHERE command
on each plane. An asterisk at the
end of the first line in the display
indicates that the controller is
partitioned. Systems are usually
only partitioned during software
upgrades when it is necessary to
isolate the different software
streams on the two main
controllers.
IN SYNCH
IN SYNCH
OUT OF
SYNCH
IN SYNCH
Enter the JOIN command first
on the inactive side, then on
the active side. Only enter this
command if you are sure that
the operating system software
is identical on both planes. Use
the WHERE command on both
planes to verify that the
software is identical.
Enter the FILE ENABLE
REDUN command on the
active plane. (You can verify
communication between the
active controller and the
inactive plane’s HDM by
entering the LOGS R OTHER
<log name> MATCH xxxx
command).
The active controller is in the
process of copying the database
from its RAM to both hard disks.
The inactive controller will not
report “IN SYNCH” until the
copying is complete.
Wait for the active controller to
finish the copying, and then
check for an “IN SYNCH” on
the inactive side.
If the inactive controller remains
OUT OF SYNCH for more than
20 minutes, the redundant file
may be corrupted.
If you suspect redundant file
corruption, see page 133
The databases on both the active No action to take. This is how
and inactive planes are identical. the system should be.
G
125
Troubleshooting
The redundant file system could
be disabled because someone
has previously entered the FILE
DISABLE REDUN command, or
because it is a new system and
the redundant file system has
never been enabled.
Action to Take
Technician’s Handbook
Flowchart 5: Continued
G
Is an alarm
present?
Yes
Flowchart 3:
An alarm is present
126
No
Troubleshooting
complete.
Troubleshooting and Repair
Flowchart 6: Maintenance Terminal Troubleshooting
Flowchart 6:
Maintenance terminal
troubleshooting
Ensure that the terminal baud rate is
set correctly. Default rate is
8N1
ASCII character set
Xon/Xoff flow control
9600 baud
Pin 4 & Pin 20 high
Reset the terminal by pressing [Ctrl] Q on
the keyboard or by resetting the power. Enter
[Ctrl] C to cancel any active commands.
Troubleshooting
Refresh the terminal screen by typing
[Ctrl] W.
Try using other baud rates
(for example, 1200).
Were you able to
correct the fault?
Yes
Troubleshooting
complete.
No
See the SX-2000 Maintenance Terminal
troubleshooting procedure on theTechnical
Documentation CD-ROM for further possible
corrective actions.
127
Technician’s Handbook
Fixing Database Errors
If the DBMS CHECK command finds errors in the database,
fix it by restoring an uncorrupted version from a DATA SAVE
backup on RSD.
Note: If a Guest Service function is performed during a DBMS Check, a major alarm is
raised because the database is not fully accessible. A subsequent DBMS
Check command will clear the error.
Restoring the Database from a DATA SAVE Backup
If your latest DATA SAVE backup is on the hard drive, you
can restore the database faster by using it. Use the DATA
QUERY command to display details about the database on
the hard drive.
Always ensure you have an up-to-date DATA SAVE backup
on RSD in case of hard disk failure.
Non-redundant Systems
1. If you don’t have an up-to-date DATA SAVE on RSD,
perform a DATA SAVE to RSD (see page 164).
2. Enter:
DBMS FLAG OFF
3. Hold down PANEL ENABLE and press A RESET.
Service is lost until you complete this procedure.
4. Insert the datasave RSD into the RSD drive.
5. Enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
RSD 15 min 6. Enter:
Tape 60 min
DATA RESTORE ∗.<volume name of RSD>
128
Troubleshooting and Repair
This message appears:
Delete old log file? (Yes/No)
Enter YES.
This message appears:
Existing Data Save will be deleted from Harddisk. Continue?
(Y/N)
Enter YES.
This message appears:
Restore system dimensions from saved data?
Enter NO.
7. If you have the Flexible Dimensioning option, this
message may appear, if not skip to step 8:
Custom Dimensions have been detected:
Overwrite the current dimensions? (y/n)
- Enter YES.
- Remove the datasave RSD.
- Hold down PANEL ENABLE and press A RESET.
8. Enter:
VOL DISMOUNT <volume name of RSD>
9. Remove the RSD.
10 min
10. Enter:
DBMS SAVE
When the save is complete, this message appears:
DBMS info: Save Completed
11. Perform the procedure Checking a Non-redundant
System on page 157.
129
Troubleshooting
- Return to step 3 of this procedure and carry on from
there.
Technician’s Handbook
Redundant Systems
1. Hold down PANEL ENABLE and press ACTIVITY
FREEZE ON.
2. Enter PARTITION first from the active plane and then
from the inactive plane.
3. From the inactive plane, enter:
DBMS FLAG OFF.
4. Hold down PANEL ENABLE and press the inactive
plane’s RESET button.
5
Log on to the inactive plane and select maintenance
mode.
6. Insert the datasave RSD into the RSD drive.
7. Enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
15 min
8. Enter:
DATA RESTORE ∗.<volume name of RSD>
If this message appears:
Delete old log file? (Yes/No)
Enter YES.
This message appears:
Existing Data Save will be deleted from Harddisk. Continue?
(Y/N)
Enter YES.
This message appears:
Restore system dimensions from saved data?
Enter NO.
9. If you have the Flexible Dimensioning option, this
message may appear, if not skip to step 10:
Custom Dimensions have been detected:
Overwrite the current dimensions? (y/n)
130
Troubleshooting and Repair
- Enter YES.
- Remove the datasave RSD.
- Hold down PANEL ENABLE and press the inactive
plane’s RESET button.
- Return to step 5 of this procedure and continue.
10. Enter:
VOL DISMOUNT <volume name of RSD>
11. Remove the RSD.
10 min
12. Enter:
DBMS SAVE.
When the save is complete, the system delivers the
following message:
DBMS info: Save Completed
13. Switch activity. Service is lost for 5 to 15 minutes.
15 min
When the JOIN command is entered, the system
delivers the following messages and prompts:
ENTER: <YES> if both planes have the same S/W
version, <NO> to cancel JOIN.
Enter YES.
After the operation is complete, this message appears:
System JOIN completed.
15. Ensure the databases on both drives are in synch by
entering FIL ST RED.
16. Hold down PANEL ENABLE and press ACTIVITY
FREEZE OFF.
17. Perform the procedure Checking a Redundant System
on page 158.
131
Troubleshooting
14. Enter JOIN first from the newly inactive plane, and then
from the newly active plane.
Technician’s Handbook
If the System Reports a Blank Database
If you set the DBMS FLAG off by issuing the DBMS FLAG
OFF command, the database is blanked during the next
system reload. If you entered the command on the active
plane of a redundant system, both planes are loaded with
the blank database after a reload.
If both planes have a blank database, restore the database
from a DATA SAVE backup (see page 128).
If only the inactive plane is blank, the redundant file may be
corrupted (see page 133).
If the System Reports that the System Dimensions
Don’t Match
If you change your system dimensions and reload the
software, the system will not download the database. The
system will report that the system dimensions don’t match
the saved database.
To recover, change the system dimensions back to the
original settings (using your old SX-2000 Feature Options
Record sheet and MITEL OPTIONS password) and reload
the system to recover your original database. Then, follow
the procedure in Performing an Option Upgrade on page
194 to change your system dimensions.
If the System Reports a SYSID Mismatch
If the system reports a SYSID mismatch, your SYSID
module is faulty or the wrong SYSID module has been
installed in your system. Contact MITEL Technical Support
for assistance.
132
Troubleshooting and Repair
Fixing Redundant File Corruption
Both of the following symptoms indicate redundant file
corruption
!
if you enter DBMS SAVE and the system responds
with DBMS SAVE COMPLETE without displaying
the following messages:
DBMS SAVE info: 10% complete.
DBMS SAVE info: 20% complete.
*
*
DBMS SAVE info: 90% complete.
DBMS SAVE info: Save completed.
!
if the active plane is IN SYNCH, but the inactive
plane remains OUT OF SYNCH for longer than 20
minutes.
To correct redundant file corruption
1. If you don’t have an up-to-date DATA SAVE on RSD,
make a DATA SAVE backup (see page 164).
2. Hold down PANEL ENABLE and press ACTIVITY
FREEZE ON.
3. Log on to the active plane and select maintenance
mode.
4. Enter:
FILE DISABLE REDUNDANCY
This message appears:
FS error: File system redundancy could not be disabled.
Reason: No such volume.
FS warning: Local disable can be attempted (Note: can
lead to FS corruption).
133
Troubleshooting
Note: Redundant File Corruption can ocurr on non-redundant systems. Recovery is
the same, but eliminate partitioning and joining steps and perform all steps that
refer to the inactive plane on the active plane of your non-redundant system.
Technician’s Handbook
FS info: Continue? (yes/no)
Enter YES
OR
This message appears:
FS info: File system redundancy disabled.
DBMS warning: Unable to read/write state file. Reason:
Node does not exist.
DBMS error: Download failed. Reason: Node does not
exist.
5. Enter:
PARTITION
This message appears:
Partition complete.
6. Log on to the inactive plane and select maintenance
mode.
7. Enter
FILE DISABLE REDUNDANCY
This message appears:
FS error: File system redundancy could not be disabled.
Reason: No such volume.
FS warning: Local disable can be attempted (Note: can
lead to FS corruption).
FS info: Continue? (yes/no)
Enter YES
OR
This message appears:
FS info: File system redundancy disabled.
DBMS warning: Unable to read/write state file. Reason:
Node does not exist.
DBMS error: Download failed. Reason: Node does not
exist.
8. Enter:
PARTITION
This message appears:
Partition complete.
134
Troubleshooting and Repair
9. Enter
VOL DISMOUNT SYSUSER
10. Enter:
VOL FORMAT DISK SYSUSER REDUND ONLY
11. Hold down PANEL ENABLE and press the inactive
plane’s RESET button.
12. Restore the database to the inactive plane (see
page 183).
Before doing a DBMS SAVE, enter the following
command: TYPE ∗.DR.LOGFILE_1 to display the log
files. Check the logs. If there are no errors, the data
restore was completed successfully.
13. Hold down PANEL ENABLE and press ACTIVITY
SWITCH. Service is lost for 5 to 15 minutes.
Troubleshooting
14. Enter:
DATE
Verify that the date is set correctly.
15. Enter:
TIME
Verify that the time is set correctly.
16. Log on to the newly inactive plane and select
maintenance mode.
17. Enter
VOL DISMOUNT SYSUSER
18. Enter:
VOL FORMAT DISK SYSUSER REDUND ONLY
19. Hold down PANEL ENABLE and press the inactive
plane’s RESET button.
20. Enter the JOIN command, first from the inactive plane
and then from the active plane.
21. Perform the procedure Checking a Redundant System
on page 158.
135
Technician’s Handbook
Power-down Procedures
Powering Down the Control Node
1. End any customer data entry sessions.
2. If you don’t have an up-to-date DATA SAVE on RSD,
perform a DATA SAVE to RSD (see page 164).
3. Hold down PANEL ENABLE and press ACTIVITY
FREEZE ON.
4. (Redundant systems only) Enter the PARTITION
command from the active plane and then from the
inactive plane.
5. (Redundant systems only) Enter the FILE STAT REDUN
command from the active plane and then from the
inactive plane. Both planes should be ISOLATED (see
Table 25 on page 125 if they are not).
6. Enter the DBMS STAT command. The DBMS initialized
flag should be ON.
7. Enter the VOL DISMOUNT SYSUSER command (if your
system is redundant, enter the command first from the
inactive plane and then from the active plane).
8. When the system confirms that SYSUSER is
dismounted, set the power switch on the power
distribution units at the rear of the main control cabinet to
“0” (OFF).
9. Disconnect the power cords from the power source.
136
Troubleshooting and Repair
Powering Down the Peripheral Nodes
1. Remove the front panels.
2. If your system is redundant, set ACTIVITY FREEZE (at
the control node) to ON.
3. Switch off the power converter.
4. Set the power switch on the rear of the node to “0” (OFF).
5. Unplug the external power cord at the rear of the node.
Powering Down the DSU Nodes
1. If your system is redundant, set ACTIVITY FREEZE (at
the control node) to ON.
2. Set the power switch on the rear of the node to “0” (OFF).
3. Unplug the external power cord at the rear of the node.
Troubleshooting
137
Technician’s Handbook
Power-up Procedures
Powering Up the Control Node
1. Ensure the control cards are installed before powering
up. Control cards cannot be installed when the system is
under power.
2. Connect the external power cord(s) at the rear of the
node.
3. Set the power switch(es) on the rear of the node to “I”
(ON).
4. (Redundant systems only) If your system is partitioned,
enter the JOIN command from the inactive plane and
then from the active plane
Powering Up the Peripheral Nodes
1. Ensure the voltage selector switch is set to the required
setting for your country.
2. Connect the external power cord at the rear of the node.
3. Set the power switch on the rear of the node to “I” (ON).
4. Switch on the power converter.
5. Complete the procedure Checking a Non-redundant
System on page 157 or Checking a Redundant System
on page 158.
6. If your system is redundant, set ACTIVITY FREEZE (at
the control node) to OFF.
138
Troubleshooting and Repair
Powering Up the DSU Nodes
1. Connect the external power cord at the rear of the node.
2. Set the power switch on the rear of the node to”I” (ON).
3. Complete the procedure Checking a Non-redundant
System on page 157 or Checking a Redundant System
on page 158.
4. If your system is redundant, set ACTIVITY FREEZE (at
the control node) to OFF.
Troubleshooting
139
Technician’s Handbook
Recovering from a Corrupted Hard Disk
To determine whether your hard disk is corrupted, enter
the following command from the maintenance terminal:
MSS
This command displays the number of soft and hard errors
on the hard disk. If hard errors are reported your hard disk is
probably corrupted. Often you can remove hard disk
corruption by formatting the disk. If not, the hard disk is
faulty, and you must replace it.
Formatting the Hard Disk
Non-redundant Systems
If you have an RSD copy of the hard disk (a VOL
BACKUP)
1
Insert the RDS copy of the VOL BACKUP in the RSD
drive.
2. Enter:
VOL DISMOUNT SYSUSER
3. Enter:
VOL FORMAT DISK SYSUSER LOAD $8000 REDUN
$10000 SCRATCH.
4. Insert the RSD labelled “MAIN Backup <volume name,
dd/mm/yyyy>” in the RSD drive. This RSD contains a
copy of the hard disk. It was made during routine
maintenance.
5. Enter:
VOL RESTORE SYSUSER FROM RSD
6. Remove the RSD from the RSD drive.
140
Troubleshooting and Repair
7. Hold down PANEL ENABLE and press A RESET.
8. Enter:
MSS
If hard disk errors are reported, you must replace the
hard disk. See Removing and Replacing a Faulty Hard
Disk on page 143. If hard disk errors are not reported and
if your RSD copy of the hard disk did not contain the
latest database, restore the current database from your
DATA SAVE RSD. See Restoring the Database from a
DATA SAVE Backup on page 128 (note: you may need
your Mitel Options Password).
If you don’t have an RSD copy of the hard drive (a VOL
BACKUP)
1. Perform a DATA SAVE to RSD. See Making a DATA
SAVE Backup on page 164.
3. Restore the database (see page 174).
4. Enter:
MSS
If hard errors are reported, you must replace the hard
disk. See Removing and Replacing a Faulty Hard Disk
on page 143. If hard disk errors are not reported and if
your RSD copy of the hard disk did not contain the latest
database, restore the current database from your DATA
SAVE RSD. See Restoring the Database from a DATA
SAVE Backup on page 128.
Redundant Systems
1. Perform a DATA SAVE to RSD. See Making a DATA
SAVE Backup on page 164.
2. Switch activity to the plane with the healthy hard disk.
141
Troubleshooting
2. Load the operating system software from the RSD (see
page 171).
Technician’s Handbook
3. Hold down PANEL ENABLE and press ACTIVITY
FREEZE ON.
4. Enter PARTITION first from the active plane then from
the inactive plane.
5. Enter FILE STAT RED from both planes. Both planes
should be isolated. But, you can continue with this
procedure providing that the active plane is isolated.
6. From the active plane, enter:
VOL SET SYSUSER READ ONLY
7. Log on to the inactive plane and select maintenance
mode.
8. Enter:
VOL DISMOUNT SYSUSER
9. Enter:
VOL FORMAT DISK SYSUSER LOAD $8000 REDUN
$10000 SCRATCH.
If this message appears:
FS info: Continue?
Enter YES
When formatting is complete, this message appears:
FS info: Formatted volume on device DISK with name
SYSUSER
10. Enter:
VOL RESTORE SYSUSER FROM OTHER
When restoration is complete, this message appears:
FS Info: Restored volume from other with name sysuser.
11. From the active plane, enter:
VOL SET SYSUSER READ WRITE
12. Hold down PANEL ENABLE and press the inactive
plane’s RESET button.
142
Troubleshooting and Repair
13. Log on to the inactive plane and select maintenance
mode.
14. Enter:
JOIN
This message appears:
JOIN COMPLETE
15. Log on to the active plane and select maintenance
mode.
16. Enter:
JOIN
Note: If the system will not join, check for redundant file
corruption, page 133.
This message appears:
JOIN COMPLETE
20 min
18. From the plane with the suspect hard disk, enter:
MSS
If hard disk errors are reported, you must replace the
hard disk. See Removing and Replacing a Faulty Hard
Disk on page 143.
Removing and Replacing a Faulty Hard Disk
1. Perform a DATA SAVE to RSD. See Making a DATA
SAVE Backup on page 164.
2. On redundant systems, switch activity to the plane with
the healthy hard disk.
3. Enter:
PARTITION
4. Hold down PANEL ENABLE and press ACTIVITY
FREEZE ON.
143
Troubleshooting
17. Wait 20 minutes, then, enter FILE STAT REDUN first
from the active plane and then from the inactive plane to
ensure that the redundant file system is synchronized.
Technician’s Handbook
5. Enter VOL DISABLE SYSUSER on the plane with the
faulty hard disk (inactive plane).
6. Power down the control node (see page 136).
7. Remove the cabinet sleeve.
Wear an anti-static wrist strap.
8. Remove the power cable from rear of the hard drive.
Disconnect the power cable from the rear of the RSD
drive directly below the hard disk drive being replaced.
In a redundant control node, it isn’t necessary to remove
the power cable from the RSD drive if you are replacing
disk drive B.
9. Disconnect the ribbon cable from the rear of the hard
disk drive.
10. From the front of the node, remove the two screws that
hold the drive carrier in place.
11. Gently slide the drive carrier from the node and remove
the four screws (two on each side) that hold the disk
drive in place.
12. Unpack the replacement disk drive. Ensure that the
address straps (A0, A1, A2) are removed and remove
the bus terminators from the drive.
13. Replace the hard disk drive.
14. Connect the power and ribbon cables.
15. Connect the external ac power cord(s) at the rear of the
node.
16. Set the power switch(es) on the rear of the node to “I”
(ON).
17. Enter VOL E SYSUSER to enable access to the sysuser
volume.
144
Troubleshooting and Repair
18. If the operating system software was not installed on the
replacement hard disk at the factory, you must load the
operating system software. For non-redundant systems,
see page 171; for redundant systems, see page 180.
Troubleshooting
145
Technician’s Handbook
Replacing Circuit Cards
Hazardous voltages can exist on installed peripheral cards
even when power is removed from the system. Grasp cards
by the lock latches only. Do not touch the sides of cards.
You can replace peripheral interface or DSU cards while the
node is operating.
Removing a Card
1. Enter:
BUSY <PLID of faulty card>
Select the COURTESY DOWN option.
2. To confirm that all circuits are in the busy state, enter:
STATE <PLID of faulty card>
Wear an anti-static wrist strap whenever you handle
circuit cards.
3. Pull the upper and lower latches outward until they are
both in the horizontal release position.
4. Draw the card toward you.
5. Immediately place the card in an anti-static bag.
Installing a Card
1. For cards that have switches, refer to the card’s hardware description for information about switch settings.
Wear an anti-static wrist strap whenever you handle
circuit cards.
2. Check the connector pins to be certain that they are
straight.
3. Slide the card into the slot.
146
Troubleshooting and Repair
4. Push the upper and lower latches away from you until
they are vertical and the card is locked in place.
5. To return the circuits to service, enter:
RTS <PLID>
Replacing a Main Controller Card
When you replace a Main Controller (MC) card, ensure that
the programmed MC card and the installed MC card match.
If they do not match, no links are assigned.
1. Remove the front panels.
2. Perform a DATA SAVE to RSD. See Making a DATA
SAVE Backup on page 164.
3. If you have a redundant system:
- Switch activity to the plane with the healthy Main
Controller card.
- Enter FILE STAT REDUN from the active plane and
then from the inactive plane. Both planes should be IN
SYNCH. If they are not, see Table 25 Status of
Redundant File System (page 125)
4. Enter:
DBMS STAT
The DBMS initialized flag should be ON.
5. Enter VOL DISMOUNT SYSUSER (from the inactive
plane).
Power down the control node before removing the
MC card. Powering down the node takes the system
out of service.
6. Set the power switch on the (inactive plane) power
distribution unit at the rear of the cabinet to “0” (OFF).
147
Troubleshooting
- Hold down PANEL ENABLE and press ACTIVITY
FREEZE ON.
Technician’s Handbook
7. Disconnect the (inactive plane) power cord from the
power source.
Wear an anti-static wrist strap whenever you handle
circuit cards.
8. Replace the old MC card with the new MC card.
Note: If you have an ETI card installed, disconnect and then
reconnect the cables as required.
9. Power up the control node (see page 138).
10. If you have a redundant system:
- From the inactive plane, enter FILE STAT REDUN.
- When the system is IN SYNCH, hold down PANEL
ENABLE and press ACTIVITY SWITCH OFF.
11. Replace the front panels.
Replacing a Peripheral Switch Controller (PSC) Card
1. If you have a redundant system, hold down PANEL ENABLE and press ACTIVITY FREEZE ON.
Step 2. takes the peripheral devices connected to the
node out of service.
2. Power down the peripheral node (see page 136).
Wear an anti-static wrist strap whenever you handle
circuit cards.
3. Replace the faulty PSC card with the new PSC card.
4. Power up the peripheral node (see page 138).
5. Hold down PANEL ENABLE and press ACTIVITY
FREEZE OFF.
148
Troubleshooting and Repair
Replacing a Control Resource Card (CRC)
1. If you have a redundant system, hold down PANEL
ENABLE and press ACTIVITY FREEZE ON.
Power down the control node before removing the
Control Resource card. Powering down the node
takes the system out of service.
2. Power down the main control node (see page 136).
Wear an anti-static wrist strap whenever you handle
circuit cards.
3. If the system has a CRCIII, disconnect the two modular
cables from the faceplate of the card.
4. Slide the CRC out of the cabinet.
5. Remove the system ID module from the connector J1 on
the faulty card.
7. Set the DIP switches on the replacement CRC faceplate
to the same settings as those on the faulty CRC.
8. Insert the replacement CRC into its cabinet slot.
9. If the system uses a CRCIII, reconnect the modular
cables to the same ports on the replacement CRC III
faceplate.
10. Power up the main control node (see page 138).
149
Troubleshooting
6. Plug the system ID module into connector J1 on the
replacement CRC. The system ID module can be
installed only one way. Ensure that you align the pins
correctly.
Technician’s Handbook
Replacing CEPT or DS1 Formatter Cards with
DS1/CEPT I or II Cards
If your system software is Lightware 31 R1.0 or higher, use
the CEPT Formatter II (MC269CA) or DS1/T1 Formatter II
(MC270CA) cards for replacement.
If your system software is Q10.7.14 or higher, use the CEPT
Formatter I (MC264CA) or DS1/T1 Formatter I (MC263CA)
cards for replacement.
1. Connect a laptop computer to the card by using a
straight through serial cable or anull modem adapter.
2. If using a modem:
- Set the modem DIP switches for initial setup according
to the manufacturer’s suggestions.
- Connect a PC to the modem, launch a VT100
emulation session, and set the serial port settings to:
Speed = 38400, Data bits = 8, Parity = none, and Stop
bits =1.
- Enter the modem command settings (according to your
type of modem), then power down the modem.
- Change the modem DIP switch settings to normal
operation.
3. Connect the modem or straight through cable, from a
laptop or PC, to the replacement card and access the
maintenance window.
4. Run acommunications package for VT100 terminal
emulation (dumb terminal) and set to 8 bits, no parity, 1
stop bit, and 38400 baud rate.
5. Enter the following information for each DS1/CEPT
Formatter I card:
- Signaling type (CAS or DPNSS)
- D-channel inversion for T1 DPNSS
- Main control version (either prior to, or after, Q10.7.8).
- Line length for T1
Note: See “DS1/CEPT Formatter I Card (MC263CA and MC264CA)
Communications” on page 111 for information on inputting the
information.
150
Troubleshooting and Repair
6. Configure the customer data entry forms
- If you are installing the CEPT or DS1/T1 Formatter II
variants, deprogram the previous CEPT or DS1 card
and reprogram the new card in the System
Configuration form. The CEPT Formatter II card and
the DS1/T1 Formatter II cards are identified as
“Universal E1” and “Universal T1” respectively.
- Program the CEPT or DS1/T1 Formatter II cards the
same as for regular trunk programming.
It is recommended that you leave the jumpers on the
CEPT and DS1/T1 Formatter II cards at the default
setting of Line Side Termination.
7. Install the Interface Assembly
- Attach the anti-static strap to your wrist.
- Unpack the Interface Assembly and ensure it is not
damaged.
- Mount the Interface Assembly extension bracket. The
closed side of the extension bracket must be to the left
when viewed from the rear of the cabinet.
- Insert the Interface Assembly. Ensure the edge
connector on the card aligns with the connector on the
backplane of the system.
- Secure the Interface Assembly to the extension
bracket with the screws provided.
8. Install the CEPT or DS1/T1 Formatter I or II Card (see
“Installing a Card” on page 146).
151
Troubleshooting
- At the rear of the cabinet, locate the DSU slot that
corresponds to the slot that you will use for the
replacement CEPT or DS1/T1 Formatter card.
Technician’s Handbook
9. Test the card
- Inspect the faceplate LEDs to verify that the card is
functioning.
Note: The replacement cards may take longer to boot-up than older card
versions.
- Open a maintenance window and verify that the trunks
associated with the corresponding channels are all in
idle state.
10. Upgrade or re-install the software:
Upgrades for the CEPT and DS1/T1 Formatter II cards
are done from the main controller each time its software
is upgraded. You can also use the force dl command
option in the VT 100 emulation window.
The CEPT and DS1/T1 Formatter I cards are not
upgradeable in the field as they come with the software
pre-loaded.
11. Reset the CEPT or DS1 Formatter I or II card using one
of the following methods:
- Entering the LOAD <PLID> command in the
maintenance window of the system.
- Unseat and reseat the card.
- Type the reset option command in the VT 100
emulation window.
152
Chapter 6
Routine Maintenance
153
Technician’s Handbook
154
Routine Maintenance
Is the System Healthy?
Non-redundant Healthy System Checklist
"
"
"
"
"
"
"
No alarms present
No database errors
DBMS Check is scheduled
DBMS Status initialized flag is ON
Programmed Reboot is scheduled
DATA SAVE backup is on RSD
Hard drive backup is on RSD
Redundant Healthy System Checklist
"
"
"
"
"
No alarms present
No database errors
DBMS Check is scheduled
DBMS Status initialized flag for both planes is ON
Redundant File System is enabled and in synch on
both planes
" Activity Switch is scheduled
" Activity Freeze is OFF (assuming that both main
controls are healthy)
" DATA SAVE backup is on RSD
" Hard drive backup is on RSD
Routine
Maintenance
155
Technician’s Handbook
Is the System Secure?
" No SECURITY alarms are present
" Passwords and usernames have been changed
" Passwords and usernames are recorded and stored
securely
"
"
"
"
"
"
"
"
"
"
156
Password expiry timer is set
CDE Form Access Authorization is complete
Account codes are programmed
SMDR records have been checked for irregularities
Auto Logout timer is set
Class of Restriction (trunks) is programmed correctly
Voice mail system is secure
Auto attendant is secure
DISA is secure
Call forwarding is secure
Routine Maintenance
Checking a Non-redundant System
1. Log on to the maintenance terminal and select
maintenance mode.
2. Enter the following commands:
Checks for system alarms. There
should be no alarms. If alarms are
present, see Flowchart 3: An Alarm is
Present on page 120.
DBMS STAT
Checks the status of the initialized
flag. The flag should be on if the
system is in sync. If the flag is off,
enter DBMS SAVE from the active
plane.
PROG R DIS
Displays the scheduled system
reset. By default, the system reboots
at 2:15 a.m. daily ONLY IF there is
memory fragmentation. To force a
system reboot at the scheduled time,
see Scheduling a System Reboot
(Non-redundant Systems) on page
95.
ME S
Checks the status of the
communication links. All
communication links should be open.
PCM TO
Checks for circuit switch link faults.
There should be no faults.
DBMS CH F
Checks the sanity and current status
of the system. The number of
detected errors should be zero.
Otherwise, there is a problem with
the database and immediate steps
should be taken to begin recovery.
Note: This step takes 60 seconds to
complete.
157
Routine
Maintenance
SH ST AL
Technician’s Handbook
Checking a Redundant System
1. Log on to the maintenance terminal and select
maintenance mode.
2. Enter the following commands (first from the active
plane, then from the inactive plane):
FIL STAT RED
Indicates whether the database on
both drives are IN SYNCH, OUT OF
SYNCH, or ISOLATED. The
databases should be IN SYNCH. If
both planes are not IN SYNCH, see
Table 25: Status of Redundant File
System on page 125.
Note: It takes approximately 15
minutes for both planes to become
synchronized.
DBMS STAT
Checks the status of the initialized
flag. The flag should be on. If the flag
is off, enter DBMS SAVE (first from
the active plane and then from the
inactive plane).
DBMS CH F
Checks the sanity and current status
of the system. The number of
detected errors should be zero.
Otherwise, there is a problem with
the database and immediate steps
should be taken to begin recovery.
Note: Check the active and inactive
planes. This step takes 60 seconds
to complete.
3. Enter the following commands from the active plane:
SH ST AL
158
Checks for system alarms. There
should be no alarms. If alarms are
present, see Flowchart 3: An Alarm is
Present on page 120.
Routine Maintenance
ACT SW SCHED Displays the scheduled automatic
activity switching. The default is 2:15
a.m. daily.
ME S
Checks the status of the
communication links. All
communication links should be open.
ME MATE
Checks the status of the mate
communication links. All links should
be open.
PCM TO
Checks for circuit switch link faults.
There should be no faults.
ACT FRE STAT
Displays the Activity Freeze Status.
Activity Freeze should be off.
Routine
Maintenance
159
Technician’s Handbook
Making Your System Secure
1. Log on to the maintenance terminal and select
maintenance mode.
2. Change your username and password if either of these
warnings appears:
“Expired password in use!”
“Default username and password in use!”
3. If someone with login privileges has left the company,
change the usernames and passwords at ALL levels.
Change the SYSTEM, INSTALLER, MAINT1, and
MAINT2 usernames and passwords by using the
DISPLAY USERNAMES, RESET USERNAMES,
RESET PASSWORD, and CHANGE PASSWORD
commands.
Change the SUPERVISOR and ATTENDANT
passwords by using the RESET PASSWORD
command.
4. In the System Options Assignment form, set the
password expiry time (number of days before password
expires). The default is 60 days.
5. Change all account codes that are known by any user
who has left the company. Use the Independent Account
Code Definition form.
6. Record usernames, passwords, and account codes.
Store them in a secure place.
7. In the Form Access Authorization form, provide access
to only the required forms for each authorization level.
8. In the System Options Assignment form, set the
Maintenance Terminal Lock-out Timer.
9. In the Trunk Service Assignment form, assign all trunks
that require a Class of Restriction (COR) to prohibit
external calls.
160
Routine Maintenance
10. In the Station Service Assignment form, assign all voice
mail ports, auto attendants, and RADs a COR that
prohibits external calls.
11. If the system requires DISA trunks, program forced
account codes in the Independent Account Code
Definition form.
If the system does not require DISA trunks, ensure that
DISA trunks are not programmed in the Miscellaneous
Assignment form.
12. If DISA is required, set the DISA failed attempts before
lock-out parameter in the System Options Assignment
form.
13. To ensure that a user cannot forward an incoming call to
a route that provides central office dial tone, set the Call
Forwarding (External Destination) option to “No” in the
Class of Service for the user’s set.
Routine
Maintenance
161
Technician’s Handbook
RSD Copier Functionality
To download a software image from the Mitel support web
site onto a laptop, connect the computer to the ethernet port
of the SX-2000 MCIIIE card, and copy the image to the PBX
RSD (removable storage device).
These commands are valid only on a switch with an MCIIIE
card programmed with the IP CONFIG command and with
an Ethernet (RJ45) connection to an ftp server (e.g. a
laptop).
A valid IP address must be assigned to the SX-2000. The IP
adress of the laptop must be assigned, as well as a user
name and password for an FTP user on the laptop. The
laptop must be configured with an FTP server.
To create and apply an upgrade or update software load:
1. Download the image file from the Mitel web site onto a
laptop.
2. Take the laptop to an SX-2000 and attach it to the
Ethernet port of the MCIIIE card.
3. Insert a formatted RSD into the RSD drive.
4. Enter the following command:
RSD COPY FROM NET <filename>Copies the file from
the network computer onto the RSD.
To copy a formatted RSD onto another RSD:
1. Issue the following command:
RSD COPY TO NET <filename>Copies an RSD to a
network computer. When the
process is complete there will be a
<filename> on the ftp server of
131032576 bytes.
RSD COPY FROM NET <filename>Copies the image
from the network PC to SX-2000
RSD.
162
Routine Maintenance
Formatting a Removable Storage
Device (RSD)
Never format an RSD with the volume name SYSUSER.
Never reset the system while you are formatting an RSD
as it will be damaged.
Never format a used RSD unless you want to erase all of
its contents.
Use the SCRATCH qualifier to re-format an RSD that was
formatted prior to LIGHTWARE™ 29 Release 3.
1. Slide the tab on the RSD to the RECORD position.
2. Insert the RSD into the RSD drive.
15 min
3. If you are using the RSD to make a DATA SAVE, enter:
VOL FORMAT RSD <volume name of RSD>
If the RSD has been previously formatted, this message
appears:
FS info: Volume already formatted with volume name:
<previous volume name>
FS info: Continue?
Enter YES
OR
If you are using the RSD to make a copy of the Hard Disk
enter:
VOL FORMAT RSD <volume name of RSD> RES
Routine
Maintenance
This message appears:
FS info: Volume already formatted with volume name:
<previous volume name>
FS info: Continue?
Enter YES
4. Enter:
VOL DISM <volume name of RSD>
5. Remove the RSD from the RSD drive.
163
Technician’s Handbook
Making a DATA SAVE Backup
The DATA SAVE command copies the database from RAM
to an RSD and to the hard disk. Perform a DATA SAVE
backup
!
before and after a software or option upgrade
!
before and after changes to the database
!
to repair corruption of the database or redundant file
system.
To protect your backups from being lost, we recommend that
you keep two copies of the database. Keep a current version
and one from your previous backup, each on a separate
RSD.
To Make a DATA SAVE Backup
1. Insert a formatted RSD in the RSD drive (see page 163).
2. Log on to the active plane and select maintenance
mode.
3. Enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
4. Enter:
DATA SAVE ∗.<volume name of RSD>
RSD 10 min
Enter YES to all prompts.
Tape 60 min
The database is copied to the RSD and to the
*.DR.CONFIG catalog on the hard drive.
When the DATA SAVE is complete, this message
appears:
Data Save completed.
5. The RSD is automatically dismounted. Remove it from
the RSD drive.
164
Routine Maintenance
Making a Message Center Backup
The MSGCTR BACKUP command copies Message Center
messages from RAM to RSD.
To Make a Message Center Backup
1. Insert a formatted RSD in the RSD drive (see page 163).
2. Log on to the active plane and select maintenance
mode.
3. Enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
4. Enter:
MSGC B ∗.<volume name of RSD>
5. Remove the RSD from the RSD drive.
Routine
Maintenance
165
Technician’s Handbook
Making an RSD Copy of the Hard Disk
The VOL BACKUP SYSUSER ON RSD command copies
the operating software, updates, options, and database to
the RSD. If a hard disk fails, you can restore the system
software from the RSD to a replacement hard disk. See
Recovering from a Corrupted Hard Disk on page 140.
The hard disk is dismounted by SYSUSER during this
procedure. Loss of service results on non-redundant
systems.
To Back Up the Hard Disk of a Non-redundant System
1. Insert a blank, formatted RSD in the RSD drive.
See Formatting a Removable Storage Device (RSD) on
page 163.
2. Enter:
VOL BACKUP SYSUSER ON RSD
When the copy is complete, this message appears:
FSinfo: Backed up volume on device RSD with name:
SYSUSER
3. Remove the RSD from the RSD drive.
4. Label the RSD "MAIN Backup <volume name,
dd/mm/yyyy>".
5. Reset the system. Service is lost.
6. Store the RSD in a safe place.
166
Routine Maintenance
To prevent loss of service on redundant systems,
perform this procedure on the inactive plane.
To Back Up the Hard Disk of a Redundant System
1. Insert a blank, formatted RSD in the RSD drive (see
page 163).
2. Set ACTIVITY FREEZE to ON.
3. Enter PARTITION from the active plane, then from the
inactive plane.
4. From the inactive plane, enter:
VOL BACKUP SYSUSER ON RSD
After the copy is complete, this message appears:
FSinfo: Backed up volume on device RSD with name:
SYSUSER
5. Remove the RSD from the RSD drive.
6. Label the RSD "MAIN Backup <volume name,
dd/mm/yyyy>".
In the following step, reset ONLY the inactive plane, or
service will be lost.
7. Press and hold PANEL ENABLE and press the RESET
button for the inactive plane.
8. Enter JOIN from the inactive plane, then from the active
plane.
9. Ensure the databases on both drives are in synch by
entering FIL ST RED.
10. Set ACTIVITY FREEZE to OFF.
11. Store the RSD in a safe place.
Routine
Maintenance
167
Technician’s Handbook
Loading Software on Your System
Software Upgrade or Software Update?
Compare the software code on the old RSD with the code on
the new RSD.
Data Restore or Data Convert?
If your new software is load P02.3.2 or later, you do not have
to do a DATA CONVERT during the software upgrade.
RSD or Tape?
This procedure refers to RSD only. If your system has a tape
unit rather than an RSD drive, substitute TAPE for RSD
when entering maintenance commands.
168
Routine Maintenance
Before You Begin
Read the Field Change Instruction (FCI) for the new
software.
!
The FCI includes the latest information about your new
software, including special upgrade notes. Read it now.
Check Your Options and Have Your Password Ready
(new passwords are not required for stream upgrades to a Lightware
stream later than Lightware 30 .)
!
Have your SX-2000 Feature Options Record sheet with
you.
!
Confirm that the options listed are the ones purchased for
the system.
!
Confirm whether the system has custom dimensions
(Flexible Dimensioning).
Prevent Data Loss
!
If you’re upgrading from ANSWER PLUS™ - ACD to
ACD 2000, see the ACD section on the MITEL Technical
Documentation CD-ROM.
!
Message Waiting lamps are turned off during a software
upgrade.
Lamps for Message Center messages can be restored
if you back up your Message Center messages before
you begin this procedure and restore them when the
upgrade is complete.
–
Lamps for voicemail messages can only be restored if
your voicemail system can be refreshed after the
upgrade is complete.
169
Routine
Maintenance
–
Technician’s Handbook
!
Usernames, passwords, alarm thresholds, Do Not
Disturb information, and SUPERCONSOLE 1000
firmkey assignments are not saved during a software
upgrade. Record this information so it can be manually
restored after the upgrade is complete.
!
If you are upgrading from a software load older than N11,
external numbers in the CDE Telephone Directory form
that have the PRM NAM field set to “YES” will be deleted
during the DATA RESTORE. Check the Telephone
Directory form to ensure that all external numbers have
the PRM NAM field set to “NO”. If you are unsure which
numbers are external, set the PRM NAM field for all
numbers to NO.
Performing a Software Upgrade
on a Non-redundant System
To Perform a Software Upgrade (Overview)
1. Save the database to RSD.
2. Load the new operating software from RSD.
3. If new feature options have been purchased, this is a
new install, or you are loading software that is earlier
than P02.3.2, enable the new options.
4. Restore the database from RSD.
Save the Database to RSD
1. Save the database to RSD. See Making a DATA SAVE
Backup on page 164.
2. If you have the Message Center option, perform a
Message Center backup see page 165.
170
Routine Maintenance
Load the Operating System Software from RSD
1. Insert the software RSD in the RSD drive.
2. Hold down PANEL ENABLE and press A RESET.
Service is lost until you complete the DATA
RESTORE.
3. Log on to the system and select maintenance mode.
4. If you are upgrading from software previous to Q26.13.1,
proceed to step 5; otherwise, proceed to step 6.
5. Enter:
FILE DIS RED
This message appears:
FS error: File system redundancy could not be disabled.
Reason: No such volume.
FS warning: Local disable can be attempted (Note: can lead to
FS corruption).
FS info: Continue? (yes/no)
Enter YES
OR
This message appears:
FS info: File system redundancy disabled.
DBMS warning: Unable to read/write state file. Reason: Node
does not exist.
DBMS error: Download failed. Reason: Node does not exist.
6. Enter:
VOL DISMOUNT SYSUSER
7. This message appears:
FS info: Dismounted volume from device DISK with name:
SYSUSER
This message appears:
FS info: Continue?
Enter YES
171
Routine
Maintenance
3 min
8. Enter:
VOL FORMAT DISK SYSUSER LOAD $8000 REDUN
$10000 SCRATCH
Technician’s Handbook
When formatting is complete, this message appears:
FS info: Formatted volume on device DISK with name:
SYSUSER
RSD 5 min
Tape 60 min
Enter:
VOL RESTORE SYSUSER FROM RSD
This message appears:
FS info: Start of Restore.
When the system has copied the system software from
the RSD to the hard disk, this message appears:
FS info: Restored volume from device RSD with name:
SYSUSER
9. Remove the software RSD from the RSD drive.
10. Hold down PANEL ENABLE and press A RESET.
10 min
11. Log on to the system and select maintenance mode.
12. Re-insert the software RSD in the RSD drive.
13. Enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
14. Enter:
UPDATE APPLY <volume name of RSD> FROM
∗.<volume name of RSD>
This message appears:
Update started.
Update applied successfully
OR
If there are no updates, this message appears:
ERROR: No update files were found
The update has NOT been applied
Ignore this error and go to the next step.
15. Enter:
VOL DISM <volume name of RSD>
16. Remove the software RSD from the RSD drive.
172
Routine Maintenance
17. If no update files were applied in step 14, proceed to the
next step.
10 min
If updates were applied in step 14, hold down PANEL
ENABLE and press A RESET.
18. Go to Enable New Options on page 173 if
• new options are included with the software
• this is a new install
• you are loading software earlier than P02.3.2
Otherwise, go to Restore the Database on page 174.
Enable New Options
1. Log on to the system and select customer data entry
mode.
2. Select System Forms from the Forms Group Menu.
3. Select Dimension and Feature Select form from the
System Forms menu. Press the <edit form> softkey.
4. Set all options to match those on the SX-2000 Feature
Options Record sheet that was shipped with the software
(X = YES).
5. Select the machine configuration FD1 (for a
MICRO-LIGHT or 9” non-redundant system) and set the
maximum number of cabinets to 5 OR FD2 (for all other
SX-2000 systems) and set the maximum number of
cabinets to 12.
6. Press the <generate> softkey then the <bottom> softkey.
8. This message appears:
Changes committed. ** Reload the system to make new values
effective. **
9. Quit the form.
173
Routine
Maintenance
7. Enter the MITEL options password (from the SX-2000
Feature Options Record sheet received with the
software), press the <commit> softkey; then press the
<confirm> softkey.
Technician’s Handbook
10. Hold down PANEL ENABLE and press A RESET.
10 min
11. Go to Restore the Database on page 174.
Restore the Database
1. Insert the datasave RSD in the RSD drive.
2. Log on to the system and select maintenance mode.
3. Enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
4. If you are loading software P02.3.2 or later, enter:
DATA RESTORE ∗.<volume name of RSD>
RSD 15 min
Tape 60 min
If you are loading software earlier than P02.3.2, see Data
Restore or Data Convert? on page 168 to determine
which command to use in this step.This message
appears:
Delete old log file? (Yes/No)
Enter YES
This message appears:
Existing Data Save will be deleted from Harddisk. Continue?
(Y/N)
Enter YES
These messages appear:
FS info: Deleting files from catalog ∗.DR.CONFIG
FS info: Deleting file ∗.DR.CONFIG.TIMESTAMP
•
•
If your software is load P02.3.2 or later, this message appears:
Restore system dimensions from saved data?
If you have NOT enabled new options
• Enter YES and proceed to step 5
If you HAVE enabled new options (or entered them
manually)
174
Routine Maintenance
• Enter NO
These messages appear:
Currently restoring: SMDR Options Assignment
Currently restoring: DTE Session Profile Assignment
•
•
Currently restoring: Traffic Options Assignment
Data Restore Complete
• Skip to step 12 if you are not using the Flexible
Dimensions option.
5. Enter the MITEL OPTIONS PASSWORD (from the
SX-2000 Feature Options Record sheet received with
the software).
If you have the Flexible Dimensions option, this message
may appear:
Custom Dimensions have been detected:
Overwrite the current dimensions? (y/n)
Enter YES
This message appears:
Restart the system to enable the RESTORED dimensions.
DATA SAVE/RESTORE/CONVERT is terminated.
6. Remove the datasave RSD from the RSD drive.
7. Hold down PANEL ENABLE and press A RESET.
This restores the dimensions from the saved data. The system
is reset to enable the options on the system.
8. Re-insert the datasave RSD in the RSD drive.
9. Log on to the system and select maintenance mode.
11. Enter:
DATA RESTORE ∗.<volume name of RSD>
175
Routine
Maintenance
10. Enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
Technician’s Handbook
This message appears:
Delete old log file? (Yes/No)
Enter YES
This message appears:
Existing Data Save will be deleted from Harddisk. Continue?
(Y/N)
Enter YES
These messages appear:
FS info: Deleting files from catalog ∗.DR.CONFIG
FS info: Deleting file ∗.DR.CONFIG.TIMESTAMP
•
•
Restore system dimensions from saved data?
Enter NO
Note: Dimenstions were input or restored in previous
steps.
These messages appear:
Currently restoring: Form Access Authorization
Currently restoring: Cabinet Assignment
•
•
Currently restoring: Traffic Options Assignment
DATA RESTORE Completed.
Reminder: DBMS SAVE will save the database.
12. Enter:
VOL DISMOUNT <volume name of RSD>
13. Remove the datasave RSD from the RSD drive.
10 min
Enter:
DBMS SAVE
These messages appear:
DBMS Info: Starting DBMS save
DBMS Save Info: 10% complete
DBMS Save Info: 20% complete
•
•
176
Routine Maintenance
DBMS Info: Save Completed
14. If your software is earlier than P02.3.2 AND you have the
Property Management System (PMS) option, hold down
PANEL ENABLE and press A RESET.
15. Enter:
TYPE ∗.DR.LOGFILE_1
Review the log for data that has not been restored. Do
not proceed to the next step until lost data has been
re-entered. Lost data may have to be re-entered
manually.
16. Reload the software into all peripheral processors, DSU
cards, DNI line cards, and attendant consoles.
For software loads P17.6.4 and later, enter:
LOAD CONTROLLERS
For software loads earlier than P17.6.4,
–
Turn power to SUPERSET 700 consoles off and then
on again.
–
Load DNI line cards. Enter:
LOAD <cabinet> <shelf> <slot>
17. Enter:
DATE yyyy-mmm-dd hh:mm:ss
For example: DATE 1999-sep-28 14:43:45.
18. Reprogram your login usernames, passwords, and
alarm thresholds.
19. Enter:
DBMS CH ON
to turn on automatic datasave checking.
20. If you have the Message Center option:
Insert the RSD with your Message Center backup in
the RSD drive
–
Enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
177
Routine
Maintenance
–
Technician’s Handbook
–
Enter:
MSGC R ∗.<volume name of RSD>
–
Enter:
VOL DISMOUNT <volume name of RSD>
21. Enter:
PROG R ON
To turn on the automatic system reload. By default, the
system reboots at 2:15 AM daily IF there is memory
fragmentation.
22. Perform the procedure Checking a Non-redundant
System on page 157.
23. The software upgrade is complete.
Performing a Software Update on a Non-redundant
System
1. Insert the software RSD into the RSD drive.
2. Enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
3. If an update already exists on the system enter:
UPDATE REMOVE
This message appears:
The Update has been removed. Please reload the main
controller from the Winchester. Also reload the slaves that
were changed (if any).
The reload is optional. Continue to the next step to save
time.
4. Enter UPDATE APPLY <volume name of RSD> FROM
∗.<volume name of RSD>.
This message appears:
The update has been successfully applied. Please, reload the
main controller from the Winchester. As well, reload the
slaves that were changed (if any).
5. Enter VOL DISMOUNT <volume name of RSD>
178
Routine Maintenance
6. Remove the RSD.
7. Enter:
DBMS STAT
The initialized flag should be on.
8. Hold down PANEL ENABLE and press A RESET.
Service is lost for 5 to 15 minutes.
15 min
9. Log on to the system and select maintenance mode.
10. Reload the software into all peripheral processors, DSU
cards, DNI line cards, and attendant consoles.
For software loads P17.6.4 and later, enter:
LOAD CONTROLLERS
For software loads earlier than P17.6.4,
–
Turn power to SUPERSET 700 consoles off and then
on again.
–
Load DNI line cards. Enter:
LOAD <cabinet> <shelf> <slot>
11. Enter:
VER
To display the update version.
12. Perform the procedure Checking a Non-redundant
System on page 157.
13. The software update is complete.
Performing a Software Upgrade on a Redundant System
To Perform a Software Upgrade (Overview)
1. Save the database to RSD.
3. If new feature options have been purchased, or this is a
new install, or you are loading software that is earlier
than P02.3.2, enable new options.
179
Routine
Maintenance
2. Load the new operating software from RSD to the
inactive plane.
Technician’s Handbook
4. Restore the database from RSD to the inactive plane.
5. Copy the software to the other plane and JOIN the
system.
Save the Database to RSD
1. Save the database to RSD. See Making a DATA SAVE
Backup on page 164.
2. If you have the Message Center option, perform a
Message Center backup on page 165.
Load the Operating System Software from RSD to the
Inactive Plane
1. Hold down PANEL ENABLE and press ACTIVITY
FREEZE ON.
2. Enter PARTITION first from the active plane, then from
the inactive plane.
3. Insert the software RSD in the RSD drive.
10 min
4. Hold down PANEL ENABLE and press the inactive
plane’s RESET button.
5. Log on to the inactive plane and select maintenance
mode.
6. If you are upgrading from software previous to Q26.13.1,
proceed to step 7;otherwise, proceed to step 8.
7. Enter:
FILE DIS RED
This message appears:
FS error: File system redundancy could not be disabled.
Reason: No such volume.
FS warning: Local disable can be attempted (Note: can lead to
FS corruption).
FS info: Continue? (yes/no)
Enter YES
OR
180
Routine Maintenance
This message appears:
FS info: File system redundancy disabled.
DBMS warning: Unable to read/write state file. Reason: Node
does not exist.
DBMS error: Download failed. Reason: Node does not exist.
8. Enter:
VOL DISMOUNT SYSUSER
This message appears:
FS info: Dismounted volume from device DISK with name:
SYSUSER
5 min
9. Enter:
VOL FORMAT DISK SYSUSER LOAD $8000 REDUN
$10000 SCRATCH
If this message appears:
FS info: Continue?
Enter YES
When formatting is complete, this message appears:
FS info: Formatted volume on device DISK with name
SYSUSER
RSD 20 min
Tape 60 min
10. Enter:
VOL RESTORE SYSUSER FROM RSD
When the system has copied the system software from
the RSD to the hard disk, this message appears:
FS info: Restored volume from device RSD with name:
SYSUSER
11. Remove the software RSD from the RSD drive.
12. Hold down PANEL ENABLE and press the inactive
plane’s RESET button.
13. Log on to the inactive plane and select maintenance
mode.
14. Re-insert the software RSD in the RSD drive.
181
Routine
Maintenance
15. Enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
Technician’s Handbook
16. Enter:
UPDATE APPLY <volume name of RSD> FROM
∗.<volume name of RSD>
This message appears:
Update started
Update applied successfully.
OR
If there are no updates, this message appears:
ERROR: No update files were found
The update has not been applied
Ignore this error and go to the next step.
17. Enter:
VOL DISM <volume name of RSD>
18. Remove the software RSD from the RSD drive.
10 min
19. If no update files were applied in step 16, proceed to the
next step.
If updates were applied in step 16, hold down PANEL
ENABLE and press the inactive plane’s RESET button.
20. Go to Enable New Options on page 182 if
• new options are included with the software
• this is a new install
• you are loading software earlier than P02.3.2.
Otherwise, go to Restore the Database to the Inactive
Plane on page 183.
Enable New Options
1. Log on to the inactive plane and select customer data
entry mode.
2. Select System Forms from the Forms Group Menu.
3. Select the Dimension and Feature Select form from the
System Forms menu. Press the <edit form> softkey.
182
Routine Maintenance
4. Set all options to match those on the SX-2000 Feature
Options Record sheet that was shipped with the software
(X = YES).
5. Select the machine configuration FD2 and set the
maximum number of cabinets to 12.
6. Press the <generate> softkey, then press the <bottom>
softkey.
7. Enter the MITEL options password (from the SX-2000
Feature Options Record sheet received with the
software); press the <commit> softkey, then press the
<confirm> softkey.
This message appears:
Changes committed. ** Reload the system to make new values
effective. **
8. Quit the form.
10 min
9. Hold down PANEL ENABLE and press the inactive
plane’s RESET button.
10. Log on to the inactive plane and enter:
PARTITION.
11. Go to Restore the Database to the Inactive Plane on
page 183.
Restore the Database to the Inactive Plane
1. Insert the datasave RSD in the RSD drive.
2. Log on to the inactive plane and select maintenance
mode.
If the Data Save was created before Q26.13.1, the RSD will
be mounted as “read-only”.
183
Routine
Maintenance
3. Enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
Technician’s Handbook
4. If you are loading software P02.3.2 or later, enter:
DATA RESTORE ∗.<volume name of RSD>
RSD 15 min
Tape 60 min
If you are loading software earlier than P02.3.2, see Data
Restore or Data Convert? on page 168 to determine
which command to use in this step.
This message appears:
Existing Data Save will be deleted from Harddisk. Continue?
(Y/N)
Enter YES
The following messages appear:
FS info: Deleting files from catalog ∗.DR.CONFIG
FS info: Deleting file ∗.DR.CONFIG.TIMESTAMP
•
•
If your software is load P02.3.2 or later, this message appears
Restore system dimensions from saved data?
If you have NOT enabled new options
• Enter YES and proceed to step 5
If you HAVE enabled new options or entered options
manually
• Enter NO
These messages appear:
Currently restoring: SMDR Options Assignment
Currently restoring: DTE Session Profile Assignment
•
•
Currently restoring: Traffic Options Assignment
Data Restore Complete
• If you are not using the Flexible Dimensions option,
skip to step 13.
5. Enter the MITEL OPTIONS PASSWORD (from the
SX-2000 Feature Options Record sheet received with
the software).
If you have the Flexible Dimensions option, this message
may appear:
184
Routine Maintenance
Custom Dimensions have been detected:
Overwrite the current dimensions? (y/n)
Enter YES
This message appears:
Restart the system to enable the RESTORED dimensions.
DATA SAVE/RESTORE/CONVERT is terminated.
6. Remove the datasave RSD from the RSD drive.
7. Hold down PANEL ENABLE and press the inactive
plane’s RESET button.
8. Log on to the inactive plane and select maintenance
mode.
9. Enter:
PARTITION
10. Re-insert the datasave RSD in the RSD drive.
11. Enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
12. Enter:
DATA RESTORE ∗.<volume name of RSD>
RSD 15 min
Tape 60 min
This message appears:
Delete old log file? (Yes/No)
Enter YES
This message appears:
Existing Data Save will be deleted from Harddisk. Continue?
(Y/N)
Enter YES
These messages appear:
FS info: Deleting files from catalog ∗.DR.CONFIG
FS info: Deleting file ∗.DR.CONFIG.TIMESTAMP
Routine
Maintenance
•
•
Restore system dimensions from saved data?
Enter NO
These messages appear:
185
Technician’s Handbook
Currently restoring: Form Access Authorization
Currently restoring: Cabinet Assignment
•
•
Currently restoring: Traffic Options Assignment
DATA RESTORE Completed.
Reminder: DBMS SAVE will save the database.
13. Enter:
VOL DISMOUNT <volume name of RSD>
14. Remove the datasave RSD from the RSD drive.
15. Enter:
TYPE ∗.DR.LOGFILE_1
Review the log for data that has not been restored. Do
not proceed to the next step until lost data has been
re-entered. Lost data may have to be re-entered
manually.
16. Enter:
DBMS SAVE
10 min
These messages appear:
DBMS Info: Starting DBMS save
DBMS Save Info: 10% complete
DBMS Save Info: 20% complete
•
•
DBMS Info: Save Completed
If progress messages do not appear and
Save Completed appears almost immediately, your redundant
file system is corrupted (see page 128).
17. If your software is earlier than P02.3.2 AND you have the
Property Management System (PMS) option, hold down
PANEL ENABLE and press the newly inactive plane’s
RESET button.
18. Hold down PANEL ENABLE and press ACTIVITY
SWITCH. Service is lost for 5 to 15 minutes.
15 min
19. From the active plane reload the software into all
peripheral processors, DSU cards, DNI line cards, and
186
Routine Maintenance
attendant consoles.
For software loads P17.6.4 and later, enter:
LOAD CONTROLLERS
For software loads earlier than P17.6.4
–
Turn power to SUPERSET 700 consoles off, then on
again.
–
Load DNI line cards. Enter:
LOAD <cabinet> <shelf> <slot>
20. Enter:
DATE yyyy-mmm-dd hh:mm:ss
For example: DATE 1999-sep-28 14:43:45
21. Proceed to Copy Upgraded Software to the Other Plane
and JOIN the System on page 187.
Copy Upgraded Software to the Other Plane and JOIN
the System
1. From the active plane, enter:
VOL SET SYSUSER READ ONLY
2. Insert the software RSD in the RSD drive.
10 min
3. Hold down PANEL ENABLE and press the inactive
plane’s RESET button.
4. Log on to the inactive plane and select maintenance
mode.
5. If you are upgrading from software previous to Q26.13.1,
proceed to step 7.; otherwise, proceed to step 6.
6. Enter:
FILE DIS RED
187
Routine
Maintenance
This message may appear:
FS error: File system redundancy could not be disabled.
Reason: No such volume.
FS warning: Local disable can be attempted (Note: can lead to
FS corruption).
FS info: Continue? (yes/no)
Enter YES
Technician’s Handbook
OR
This message may appear:
FS info: File system redundancy disabled.
DBMS warning: Unable to read/write state file. Reason: Node
does not exist.
DBMS error: Download failed. Reason: Node does not exist.
7. Enter:
VOL DISMOUNT SYSUSER
This message appears:
FS info: Dismounted volume from device DISK with name:
SYSUSER
8. Enter:
VOL FORMAT DISK SYSUSER LOAD $8000 REDUN
$10000 SCRATCH
If this message appears:
FS info: Continue?
Enter YES
When formatting is complete, this message appears:
FS info: Formatted volume on device DISK with name
SYSUSER
9. Enter:
VOL RESTORE SYSUSER FROM OTHER
20 min
When the active plane’s software has been copied to the
inactive plane’s hard disk, this message appears:
FS info: Restored volume from OTHER with name
SYSUSER.
10. Log on to the active plane and enter:
VOL SET SYSUSER READ WRITE
11. Remove the software RSD from the RSD drive.
12. Hold down PANEL ENABLE and press the inactive
plane’s RESET button.
10 min
13. Log on to the inactive plane and enter:
JOIN
Wait for this message to appear:
JOIN COMPLETE.
188
Routine Maintenance
20 min
14. Log on to the active plane and enter:
JOIN
The inactive plane resets.
15. Wait 10 - 20 minutes, then enter FILE STAT REDUN first
from the active plane and then from the inactive plane.
The system should be IN SYNCH. Once the system is
synchronized, the database is downloaded to the
inactive plane.
16. Enter DBMS STAT first from the active plane and then
from the inactive plane. The initialized flag should be ON.
17. Reprogram your login usernames, passwords, and
alarm thresholds.
18. Enter:
DBM CH ON
To turn on automatic database checking.
19. If you have the Message Center option:
–
Insert the RSD with your Message Center backup in
the RSD drive
–
Enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
–
Enter:
MSGC R ∗.<volume name of RSD>
–
Enter:
VOL DISMOUNT <volume name of RSD>
20. Enter:
DBMS CH FULL
to check for database errors. If errors are found, see
Fixing Database Errors on page 128.
Routine
Maintenance
21. Enter:
ACT S S <day> <hh:mm>
To turn on automatic activity switching.
22. Hold down PANEL ENABLE and press ACTIVITY
FREEZE OFF.
189
Technician’s Handbook
23. Perform the procedure Checking a Redundant
System on page 158.
24. The software upgrade is complete.
Performing a Software Update on a Redundant System
Copy the Software Updates from RSD to the Inactive Plane
1. Hold down PANEL ENABLE and press ACTIVITY
FREEZE ON.
2. Enter PARTITION first from the active plane then from
the inactive plane.
3. Enter FIL STAT REDUN first from the active plane then
from the inactive plane. The system should be isolated.
4. Insert the software RSD in the RSD drive.
5. From the inactive plane, enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
6. If an update already exists on the system enter:
UPDATE REMOVE
This message appears:
The Update has been removed. Please reload the main
controller from the Winchester. Also reload the slaves that
were changed (if any).
The reload is optional. Continue to the next step to save time.
7. Enter UPDATE APPLY <volume name of RSD> FROM
∗.<volume name of RSD>.
This message appears:
The update has been successfully applied. Please, reload the
main controller from the Winchester. As well, reload the
slaves that were changed (if any).
8. Enter:
VOL DISMOUNT <volume name of RSD>
9. Remove the RSD from the RSD drive.
190
Routine Maintenance
10. Hold down PANEL ENABLE and press the inactive
plane’s RESET button.
11. Log on to the inactive plane and select maintenance
mode.
12. To check the update version, enter:
VER
13. Hold down PANEL ENABLE and press ACTIVITY
SWITCH. Service is lost for 5 to 15 minutes.
15 min
14. Log on to the newly active plane and select maintenance
mode.
15. Reload the software into all peripheral processors, DSU
cards, DNI line cards, and attendant consoles.
For software loads P17.6.4 and later, enter:
LOAD CONTROLLERS
For software loads earlier than P17.6.4,
–
Turn power to SUPERSET 700 consoles off then on
again.
–
Load DNI line cards. Enter:
LOAD <cabinet> <shelf> <slot>
Copy the Software Updates from RSD to the Other Plane
1. Log on to the inactive plane and select maintenance
mode.
2. Insert the software RSD in the RSD drive.
4. Enter UPDATE APPLY <volume name of RSD> FROM
∗.<volume name of RSD>
191
Routine
Maintenance
3. From the inactive plane, enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
Technician’s Handbook
If this message appears:
Main Controller update applied successfully.
The update has been successfully applied.
–
Updates have been applied. Proceed to the next step.
If this message appears:
ERROR: No update files were found
–
There are no updates on the RSD. Proceed to the next
step.
If this message appears:
ERROR: An update already exists on the system. UPDATE
REMOVE must be executed.
–
Enter:
UPDATE REMOVE
This message appears:
The Update has been removed.
Please, reload the main controller from the Winchester. As
well, reload the slaves that were changed (if any).
–
Enter:
UPDATE APPLY <volume name of RSD> FROM
*.<volume name of RSD>
This message appears:
The update has been successfully applied. Please, reload the
main controller from the Winchester. As well, reload the
slaves that were changed (if any).
–
Proceed to the next step.
5. Enter:
VOL DISMOUNT <volume name of RSD>
6. Remove the RSD from the RSD drive.
7. Hold down PANEL ENABLE and press the inactive
plane’s RESET button.
8. Log on to the inactive plane and select maintenance
mode.
192
Routine Maintenance
9. To check the update version, enter:
VER
JOIN the Planes
1. Log on to the inactive plane and select maintenance
mode.
2. Enter:
JOIN
Enter YES to the prompt.
This message appears:
Join Complete.
3. Log on to the active plane.
4. Enter
JOIN
Enter YES to the prompt.
When the operation is complete, the following
message appears:
System JOIN completed.
20 min
5. Wait 20 minutes, then enter FILE STAT REDUN first
from the active plane and then from the inactive plane.
The system should be IN SYNCH.
6. Enter DBMS STAT first from the active plane and then
from the inactive plane. The initialized flag should be on.
7. Hold down PANEL ENABLE and press ACTIVITY
FREEZE OFF.
8. Perform the procedure Checking a Redundant
System on page 158.
9. The software update is complete.
Routine
Maintenance
193
Technician’s Handbook
Performing an Option Upgrade
Options and MFRDs are Password Protected
Options and MFRDs are password protected. Call the
MITEL order desk to purchase a new set of options. You will
be given a new MITEL Options Password that will enable the
options and MFRDs on the system.
Before You Begin
Read the instructions outlined on page 169.
Enabling Options and MFRDs on Non-redundant
Systems
1. Make a DATA SAVE to RSD. See Making a DATA SAVE
Backup on page 164.
2. If you have the Message Center option, save message
center messages to RSD. See Making a Message
Center Backup on page 165.
3. Record your login usernames, passwords, and alarm
thresholds.
4. If required, record SUPERCONSOLE 1000 firmkey
programming.
5. Log on to the system and select customer data entry
mode.
6. Select System Forms from the Forms Group Menu.
7. Select the Dimension and Feature Select form from the
System Forms menu. Press the <edit form> softkey.
8. Set all options to match those on the SX-2000 Feature
Options Record sheet (X = YES).
9. Verify that the machine configuration is FD1 for a MICRO
LIGHT, or 9” redundant system, and that the maximum
194
Routine Maintenance
number of cabinets is 5. Otherwise select FD2 and a
maximum number of 12 cabinets.
10. Press the <generate> softkey followed by the <bottom>
softkey.
11. Enter the MITEL options password (from the SX-2000
Feature Options Record sheet received with the
software); press the <commit> softkey, then the
<confirm> softkey.
This message appears:
Changes committed. ** Reload the system to make new values
effective. **
12. Quit the form.
13. Select maintenance mode and enter:
DBMS FLAG OFF
14. Hold down PANEL ENABLE and press the plane A
RESET button to enable the options. Service is lost
until you complete the DATA RESTORE.
15. Log on to the system and select maintenance mode.
16. Insert the datasave RSD in the RSD drive.
17. Enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
18. Enter:
DATA RESTORE ∗.<volume name of RSD>
RSD 15 min
Tape 60 min
This message appears:
Delete old log file? (Yes/No)
Enter YES
These messages appear:
FS info: Deleting files from catalog ∗.DR.CONFIG
FS info: Deleting file ∗.DR.CONFIG.TIMESTAMP
195
Routine
Maintenance
This message appears:
Existing Data Save will be deleted from Harddisk. Continue?
(Y/N)
Enter YES
Technician’s Handbook
•
•
If your software is load P02.3.2 or later, this message
appears:
Restore system dimensions from saved data?
Enter NO
Note: Dimensions have been input previously.
If you have enabled the Flexible Dimensioning option,
this message appears:
Custom dimensions have been detected: overwrite the current
dimensions?
Enter YES
If you have enabled Hotel options, this message
appears:
Restore Hotel/Motel wake-up and room status data? (yes/no)
Enter YES
These messages appear:
Currently restoring: SMDR Options Assignment
Currently restoring: DTE Session Profile Assignment
•
•
Currently restoring: Traffic Options Assignment
Data Restore Complete
19. If you have the Message Center option, restore the
Message Center messages. Enter:
MSGC R ∗.<volume name of RSD>
20. Enter
VOL DISMOUNT <volume name of RSD>
21. Remove the RSD from the RSD drive.
22. Enter
DBMS SAVE
10 min
196
Routine Maintenance
This message appears:
DBMS info: Request has been queued.
DBMS info: Starting DBMS Save
DBMS SAVE info: 10% complete.
DBMS SAVE info: 20% complete.
•
•
DBMS SAVE info: 90% complete.
DBMS info: Save Completed
23. Enter:
DATE yyyy-mmm-dd hh:mm:ss
For example: DATE 1999-sep-28 14:43:45
24. Turn on automatic database checking. Enter:
DBM CH ON
25. Reprogram your login usernames, passwords, and
alarm thresholds.
26. If required, re-program the SUPERCONSOLE 1000
firmkeys.
27. Perform the procedure Checking a Non-redundant
System on page 157.
28. The options upgrade is complete.
Enabling Options and MFRDs on Redundant Systems
1. Hold down PANEL ENABLE and press ACTIVITY
FREEZE ON.
2. Enter PARTITION from the active plane.
This message appears:
System PARTITION completed.
197
Routine
Maintenance
This message appears:
ENTER <YES> to proceed with PARTITION, <NO> to
cancel request.
Enter YES.
Technician’s Handbook
3. Enter PARTITION from the inactive plane.
This message appears:
ENTER <YES> to proceed with PARTITION, <NO> to
cancel request.
Enter YES.
This message appears:
System PARTITION completed.
4. Make a DATA SAVE to RSD from the inactive plane (see
page 164).
5. If you have the Message Center option, save message
center messages to RSD (see page 165).
6. Record your login usernames, passwords, and alarm
thresholds.
7. If required, record SUPERCONSOLE 1000 firmkey
programming.
8
Log on to the inactive plane and select customer data
entry mode.
9. Select System Forms from the Forms Group Menu.
10. Select the Dimension and Feature Select form from the
System Forms menu. Press the <edit form> softkey.
11. Ensure all options match those on the SX-2000 Feature
Options Record sheet (X = YES).
12. Verify that the machine configuration is FD2 and that the
maximum number of cabinets is set to 12.
13. Press the <generate> softkey, followed by the <bottom>
softkey.
14. Enter the MITEL options password (from the SX-2000
Feature Options Record sheet received with the
software; press the <commit> softkey, then the
<confirm> softkey.
This message appears:
Changes committed. ** Reload the system to make new values
effective. **
198
Routine Maintenance
15. Quit the form.
16. Select maintenance mode and enter:
DBMS FLAG OFF
17. Hold down PANEL ENABLE and press the inactive
plane’s RESET button.
18. Log on to the inactive plane and select maintenance
mode.
19. Insert the datasave RSD in the RSD drive.
20. Enter:
VOL MOUNT RSD
Read the volume name of the RSD from the system
response on the maintenance terminal.
21. Enter
DATA RESTORE ∗.<volume name of RSD>
RSD 15 min
Tape 60 min
This message appears:
Delete old log file? (Yes/No)
Enter YES
This message appears:
Existing Data Save will be deleted from Harddisk. Continue?
(Y/N)
Enter YES
These messages appear:
FS info: Deleting files from catalog ∗.DR.CONFIG
FS info: Deleting file ∗.DR.CONFIG.TIMESTAMP
If you have enabled Hotel options, this message
appears:
Restore Hotel/Motel wake-up and room status data? (yes/no)
199
Routine
Maintenance
•
•
If your software is load P02.3.2 or later, this message
appears:
Restore system dimensions from saved data?
Enter NO (options have been input previously)
Technician’s Handbook
Enter YES
These messages appear:
Currently restoring: SMDR Options Assignment
Currently restoring: DTE Session Profile Assignment
•
•
Currently restoring: Traffic Options Assignment
Data Restore Complete
22. If you have the Message Center option, restore the
Message Center messages. Enter
MSGC R ∗.<volume name of RSD>
23. Enter
VOL DISMOUNT <volume name of RSD>
24. Remove the RSD from the RSD drive.
10 min
25. Enter DBMS SAVE
This message appears:
DBMS info: Request has been queued.
DBMS info: Starting DBMS Save
DBMS SAVE info: 10% complete.
DBMS SAVE info: 20% complete.
•
•
DBMS SAVE info: 90% complete.
DBMS info: Save Completed
15 min
26. Hold down PANEL ENABLE and press ACTIVITY
SWITCH. Service is lost for 5 to 15 minutes.
27. Enter DATE yyyy-mmm-dd hh:mm:ss
For example: DATE 1999-sep-28 14:43:45
28. Turn on automatic database checking. Enter:
DBMS CH ON
29. Reprogram your login usernames, passwords, and
alarm thresholds.
30. If required, re-program the SUPERCONSOLE 1000
firmkeys.
200
Routine Maintenance
31. Enable the new options on the newly inactive plane.
32. Repeat steps 8 to 14.
33. Hold down PANEL ENABLE and press the inactive
plane’s RESET button.
34. Enter JOIN from the inactive plane.
This message appears:
ENTER <YES> if both planes have the same S/W version,
<NO> to cancel JOIN.
Enter YES
This message appears:
System JOIN completed.
35. Enter JOIN from the active plane.
This message appears:
ENTER <YES> if both planes have the same S/W version,
<NO> to cancel JOIN.
Enter YES
This message appears:
System JOIN completed.
36. Perform the procedure Checking a Redundant
System on page 158.
37. Hold down PANEL ENABLE and press ACTIVITY
FREEZE OFF.
38. Make a new DATA SAVE backup (see page 164).
Routine
Maintenance
201
Technician’s Handbook
202
Index of Maintenance Commands
Index of Maintenance Commands
Symbols
+dchan-inv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
[Ctrl] C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
[Ctrl] W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
[Esc] [Ctrl] J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
A
ACTivity FREeze ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACTivity FREeze STATUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACTivity Switch <plid> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACTivity Switch Force . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACTivity Switch ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACTivity Switch Schedule <day> <hh:mm> . . . . . . . . . . . . . . . .
ALarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
91
91
91
91
92
91
85
B
BACkground ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
BACkground ON/OFF <category> . . . . . . . . . . . . . . . . . . . . . . . 92
BACkground Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
BAUd <NNNN> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
BAUd <NNNN> <port name> . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
BUsy <plid of CEPT or DS1 formatter card> <hybrid> . . . . . . . 108
BUsy <plid> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
BUsy APNss Group <#> Traffic/Signalling/All . . . . . . . . . . . . . 108
C
CANcel Print <job number> . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
CANcel Print <job number> /PORT <port name> . . . . . . . . . . . 83
CANcel Print ALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
CATalog Info <pathname> FULL . . . . . . . . . . . . . . . . . . . . . . . . 84
CHange Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
CONFiguration Long <plid> . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
CONGestion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
CP Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80, 80, 80
D
DATA CONVert *.<volume name of RSD> . . . . . . . . . . . . . . . 100
DATA Query . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
DATA Query *.<volume name of RSD> . . . . . . . . . . . . . . . . . . 100
203
Technician’s Handbook
DATA Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
DATA Restore *.<volume name of RSD> . . . . . . . . . . . . . . . . . 99
DATA SAve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
DATA SAve *.<volume name> . . . . . . . . . . . . . . . . . . . . . . . . . . 99
DATE <yyyy-mmm-dd> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
DBMs CHeck FULL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
DBMs CHeck KILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
DBMs CHeck ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
DBMs Check Time <hh> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
DBMs Download *.<volume name> . . . . . . . . . . . . . . . . . . . . . . 99
DBMs FLag OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
DBMs Query . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
DBMs SAve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
DBMs SAve *.<volume name of RSD> . . . . . . . . . . . . . . . . . . . 99
DBMs STATus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
-dchan-inv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
DESktop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
DESktop [Return] [Esc] 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
dis opt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
DISable Seize TEst . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
DISPlay Usernames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
DTstat Clear <plid> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
DTstat Read <plid> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
DTstat Read APNss Group <number> . . . . . . . . . . . . . . . . . . 108
E
ENable Print /Nonqueued . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
F
FILe CReate <pathname>.<catalog name> CATalog . . . . . . . . 84
FILe DISable Redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
FILe ENable Redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
FILe STatus REDundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
FIRmware ALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
FIRmware ALLEprom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
FIRmware Cardtype <card type> . . . . . . . . . . . . . . . . . . . . . . . . 93
FIRmware KILL ALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
FIRmware KILL PLID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
FIRmware KILL SET <set type> . . . . . . . . . . . . . . . . . . . . . . . . 94
FIRmware PAnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
FIRmware PLID <plid> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
204
Index of Maintenance Commands
force dl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
FOrmprint <form name> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
FOrmprint <form name> /ALL /PORT <port name> . . . . . . . . . . 82
FOrmprint <form name> /ALL /PORT LPR3 . . . . . . . . . . . . . . . . 81
FOrmprint <form name> /INSTANCE n /PORT <port name> . . 81
FOrmprint <form name> /PORT <port name> . . . . . . . . . . . . . . 81
H
HELp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
HELp <command> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
J
JOin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
L
LANguage Select <language> ALL FROM *.<catalog> . . . . . . . 77
line len # . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
LOAd <plid> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
LOAd Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
LOCate ALL FREE DN <dn start> TO <dn end> EXT . . . . . . . 106
LOCate ALL FREE PLID <card type> <plid start> TO <plid end> .
106
LOCate EXtension <extension number> . . . . . . . . . . . . . . . . . 105
LOCate FEature EXtension <extension number> . . . . . . . . . . 105
LOCate FEature PLID <plid> . . . . . . . . . . . . . . . . . . . . . . . . . . 105
LOCate FIRST FREE DN <dn start> TO <dn end> EXT . . . . . 106
LOCate FIRST FREE PLID <card type> <plid start> TO <plid end>
106
LOCate NUMber <number> . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
LOCate PLID <plid> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
LOCATE TENANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105, 105
LOCate Trunk <trunk number> . . . . . . . . . . . . . . . . . . . . . . . . . 105
LOGSys Attributes <log name> . . . . . . . . . . . . . . . . . . . . . . . . . 90
LOGSys CAncel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
LOGSys PRInt <log name> . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
LOGSys PRInt <log name> ALL . . . . . . . . . . . . . . . . . . . . . . . . . 90
LOGSys PURge <log name> . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
LOGSys Read <log name> ALL MAtch "xxxx" . . . . . . . . . . . . . . 89
LOGSys Read <log name> NEW/OLD <#> MAtch "xxxx" . . . . . 89
LOGSys Read <log name> NEWest/OLDest <#> . . . . . . . . . . . 89
LOGSys Read OTHER <log name> ALL MAtch "xxxx" . . . . . . . 89
205
Technician’s Handbook
LOGSys Size <SMDR> FILE <entry count> . . . . . . . . . . . . . . . 90
M
main old . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
MAintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
MEssage MATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
MEssage R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
MEssage SUB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
MOVe ADD <“lastname, firstname”> TO <extension number> 107
MOVe DELete <“lastname, firstname”> FROM <extension number>
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
MOVe RENumber <old number> TO <new number> . . . . . . . 107
MOVe Swap <X> WITH <Y> . . . . . . . . . . . . . . . . . . . . . . . . . . 107
MOVe User <X> TO <Y> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
MSGCtr Backup *.<volume name of RSD> . . . . . . . . . . . . . . . 100
MSGCtr Restore *.<volume name of RSD> . . . . . . . . . . . . . . . 100
MSSstats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
MYprinter <printer name> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
N
NEsync SUmmary <shelf # of synch source> . . . . . . . . . . . . .
NEsync SUmmary <shelf> LAST <number of hours> . . . . . . .
NEtsync SEtsource <source #> . . . . . . . . . . . . . . . . . . . . . . . .
NEtsync SEtsource AUTO . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NEtsync SEtsource FREERUN . . . . . . . . . . . . . . . . . . . . . . . .
NEtsync STate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
109
110
109
109
109
109
P
PARIty <XYZ> <port name> . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
PARTition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
PCM STATUS <Tx or Rx> <link number> . . . . . . . . . . . . . . . . . 95
PCM TEst Both <link> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
PCM TOtals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
PRInt *.MAINTENANCE.SESSION_LOG /PORT <printer port> 85
PRInt <filename> /PORT <port name> . . . . . . . . . . . . . . . . . . . 81
Print <filename> /PORT LPR3 . . . . . . . . . . . . . . . . . . . . . . . . . . 81
PROGrammed Reboot Display . . . . . . . . . . . . . . . . . . . . . . . . . 95
PROGrammed Reboot Memory Daily <hh:mm:ss> . . . . . . . . . . 95
PROGrammed Reboot ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . 95
PROGrammed Reboot SCHedule <DAILY or day of week>
<hh:mm:ss> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
206
Index of Maintenance Commands
PROM <plid> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
R
RCD <plid> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
RESEt Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
RESet Username <user> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
RESOurces <plid> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
RESOurces VIRTUAL <plid> . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
RESOurces XNET <trunk> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
RSD CANCEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
RSD COPY FROM NET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
RSD COPY TO NET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
RSD VERIFY NET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
RTS <plid of CEPT or DS1 formatter card> <hybrid or link> . . 109
RTS <plid> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
RTS APNss Group <#> Traffic/Virtual/ALL . . . . . . . . . . . . . . . 109
RTS TRUNK GROUP <group number> ALL . . . . . . . . . . . . . . . 87
S
SESsion End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
SESsion Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
SET Threshold <alarm category> <x> <y> <z> . . . . . . . . . . . . . 86
SHow FAults <alarm category> . . . . . . . . . . . . . . . . . . . . . . . . . 85
SHow FAults ALarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
SHow Print <printer port name> . . . . . . . . . . . . . . . . . . . . . . . . . 83
SHow Print ALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
SHow Seize TEst . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
SHow STatus ALarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
sig cas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
sig dpnss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
STate <plid> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
STate MLS <plid> <circuit> <line appearance number> . . . . . . 86
SYstem Totals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
T
TEst <plid> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
TEst <plid> Continuous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
TEst <plid> SEize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
TEst <plid> Until Fail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
TEst APNss Group <#> Traffic/Signalling/All . . . . . . . . . . . . . . 108
207
Technician’s Handbook
TEst Hybrid <plid of CEPT or DS1 formatter card>
<hybrid or link> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
TEst Trunk Group <group number> . . . . . . . . . . . . . . . . . . . . . . 88
TIme <hh:mm:ss> AM/PM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
TRAFfic Delete <mmm-dd hh:mm> . . . . . . . . . . . . . . . . . . . . . . 97
TRAFfic Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
TRAFfic Print <mmm-dd hh:mm:ss> . . . . . . . . . . . . . . . . . . . . . 97
TRAFfic STAtus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
TRAFfic STOp <mmm-dd hh:mm> . . . . . . . . . . . . . . . . . . . . . . 97
U
Using the FIRM KILL command . . . . . . . . . . . . . . . . . . . . . . . . . 93
V
VErsion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
VOlume Backup <volume name> ON <device> . . . . . . . . . . . 102
VOlume DISAble <volume name> . . . . . . . . . . . . . . . . . . . . . . 103
VOlume DISMount <volume name> . . . . . . . . . . . . . . . . . . . . 102
VOlume Enable <volume name> . . . . . . . . . . . . . . . . . . . . . . . 103
VOlume Format <RSD> <volume name> RES . . . . . . . . . . . . 104
VOlume Format <RSD> <volume name> RES SCRatch . . . . 104
VOlume Format DISK SYSUSER REDundancy ONLY . . . . . . 104
VOlume Info <volume name> . . . . . . . . . . . . . . . . . . . . . . . . . 102
VOlume Mount <device> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
VOlume Restore <volume name> FROM <device> . . . . . . . . 103
VOlume Restore SYSUSER FROM OTHER . . . . . . . . . . . . . . 103
VOlume Set SYSUSER READ ONLY . . . . . . . . . . . . . . . . . . . 103
VOlume Set SYSUSER READ WRITE . . . . . . . . . . . . . . . . . . 103
W
WHere . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79, 102
208
Index
A
Accessing desktop mode 77
Activity status, main controller 102
Adding users 107
Alarms
setting thresholds 86
showing 85
showing faults 85
Assigning a new default printer 84
Attendant console, programming 57
B
Back up
a volume 102
message center messages 100
Backup
DATA SAVE 164, 165
hard disk 166
of customer database 164, 165
Baud rate
of maintenance port 80
of specified port 80
Blank database, recovery 132
Bootstrap sequence 115
Busying out a card, circuit, or channel
for testing 87
C
Cabinet card layouts 9
Cabling
cable connectors 29
peripheral interface cabling 29
Call rerouting, programming 63
Cancelling
a maintenance command 81
a print job 83
Cards
cabinet card layouts 9
displaying configuration of 92
identifying 94
replacing 146
settings of 24
X-connect fields 32
Cartridge tape, formatting 164
Catalogs
creating 84
displaying 84
CDE
forms, printing 81
switching to maintenance 78
CEPT interface assembly jumpers 27
Changing
a phone’s attributes 60
baud rate 80
extension numbers 107
parity of a console port 80
parity of DNIC port 80
passwords 78
system date 79
system time 79
Changing MFRDs 194
Checking
a non-redundant system 157
a redundant system 158
for MSS errors 94
log parameters 90
the database 98
the print queue 83
Checklist for non-redundant system
155
Circuits
busying out 87
returning to service 87
testing 88
Clock source, synchronization of 109
Commands
cancelling 81
displaying previously issued 79
getting help 77
Control cabinet card layout
non-redundant 10
redundant 9
Control cards, table of 23
Control node
powering down 136
209
Technician’s Handbook
powering up 138
Control resource card
replacement 149
switch settings 24
Courtesy down, removing request 87
Creating a catalog 84
D
Database
backing up 164, 165
checking 98
errors, fixing 128
saving, restoring 99
Date, changing or reading 79
Deleting
log entries 90
telephone users 107
Desktop mode
accessing 77
switching to maintenance 78
Diagnostics, turning on/off 92
Dial in trunks, programming 67
Digital link, displaying status 108
Directory numbers, finding 106
DISA
dial in trunk programming 67
non-dial in trunk programming 68
Disabling
access to a volume 103
file redundancy 101
Dismounting a volume 102
Displaying
call path of a set 89
card configuration 92
catalogs 84
information on a volume 102
state of line appearances 86
status of digital links 108
synchronization information 109
system resource totals 86
system software revision 79
system software versions 79
DS1 formatter card switches 27
210
DSU
cabinet
adding 17
cards
table of 22
DSU nodes
powering down 137
powering up 139
E
E & M trunk card settings 25
Enabling
access to a volume 103
file redundnacy 101
options 194
Errors
checking for MSS errors 94
fixing database errors 128
Exiting desktop mode 77
Extension
changing number of 107
locating 105
F
Faults, showing 85
Features
active on a plid 105
active on an extension 105
file corruption, fixing 133
File redundancy, enabling, disabling
101
Finding directory numbers 106
Firmware, identifying 92
Fixing database errors 128
Fixing redundant file corruption 133
Formatting
cartridge tape 164
commands 104
hard disk, non-redundant system
140
RSD 163
volume 104
Index
G
Getting help 77
H
Hard disk
backing up 166
checking for errors 94
formatting, non-redundant system
Logs
checking parameters 90
deleting 90
setting file size 90
starting, ending, printing 85
M
Identifying
cards 94
firmware 92
system resource shortages 92
Main controller card, replacement 147
Main controller, activity status 102
Maintenance
port characteristics 215
Maintenance mode, switching to 78
Message center
backing up 100
restoring 100
MFRDs, changing 194
MICRO LIGHT cabinet
card layout 11
valid card combinations 12
Mounting a volume 102
Moving phone users 61
J
N
140
recovery 140
removal and replacement 143
Help
displaying
commands 77
explanations 77
I
Joining a redundant system 101
Jumper settings, PRI NT and LT 28
Jumpers, on CEPT interface assembly
27
L
Languages, selecting 77
Line appearances, displaying 86
Line Termination, PRI 28
Link, displaying status of 108
Listing the active features
for a plid 105
for an extension 105
Loading software
into a card’s processor 94
on non-redundant systems 168
on redundant systems 179
Locating
an extension or trunk 105
where a number is used 105
Logging out 77, 215
Network Termination, PRI 28
Non-dial in trunks, programming 66
Non-redundant system
checking 157
checklist 155
control cabinet card layout 10
Numbers, locating where used 105
O
OPS line card switches 26
Options, enabling 194
P
Parity
console port 80
DNIC port 80
Partitioning and joining 101
Password
changing 78
resetting 78
PCM links, testing 95
211
Technician’s Handbook
Peripheral cabinet
adding 17
card layout 15
Peripheral interface cabling 29
Peripheral interface cards
table of 20
Peripheral nodes
powering down 137
powering up 138
Peripheral switch controller card,
replacement 148
Phone attributes, changing 60
Pin designations, for USCO 29
Ports, printer 48
Powering down
control node 136
DSU nodes 137
peripheral nodes 137
Powering up
control node 138
DSU nodes 139
peripheral nodes 138
PRI card, Line Termination 28
PRI card, Network Termination 28
Printing
assigning a default printer 84
cancelling a print job 83
CDE forms 81
checking the queue 83
log files to a local printer 81
programming ports 48
to LPR3 81
Programming
attendant consoles 57
call rerouting always 63
dial in trunks 67
DISA dial in trunks 67
DISA non-dial in trunks 68
non-dial in trunks 66
printer ports 48
the telephone directory 59
voice stations 52
212
Q
Queue, checking print queue 83
Quitting desktop mode 77
R
Reading maintenance logs 89
Recovering from a corrupted hard disk
140
Recovery, system dimensions 132
redundant file coruption, fixing 133
Redundant system
checking 158
checklist 155
control cabinet card layout 9
scheduling an activity switch 91
switching activity 91
Refreshing the terminal screen 80
Removing
a faulty hard disk 143
courtesy down request 87
Replacing
circuit cards 146
control resource card 149
faulty hard disk 143
main controller card 147
peripheral switch controller 148
Resetting passwords 78
Resources, identifying shortages 92
Restoring
a volume 102
the database 99
Returning a busy circuit or trunk to
service 87
RSD Copier Functionality 162
RSD, formatting 163
S
Saving the database 99
Scheduling
an activity switch 91
Selecting a different language 77
Session logs 85
Index
Setting
alarm thresholds 86
card settings 24
the size of the SMDR log file 90
Showing
alarms 85
faults 85
Software
displaying the revision 79
displaying the version 79
loading on non-redundant systems
168
loading on redundant systems 179
Stepping back through commands 79
Swapping users 107
Swapping users’ phones 62
Switches
on CRC 24
on DS1 formatter card 27
on E & M trunk card 25
on OPS line card 26
Switching
activity (redundant systems) 91
terminal from screen mode to print
mode 84
to maintenance mode 78
Synchronization
displaying information 109
of the clock source 109
SYSID mismatch, recovery 132
System dimension mismatch 132
System resources, displaying 86
T
Tape, formatting 164
Telephone directory, programming 59
Terminal
refreshing screen 80
switching to print mode 84
Testing
circuits 88
digital trunks 108
PCM links 95
trunks 88
Time, changing or reading 79
Trunks
locating 105
returning to service 87
testing digital trunks 108
Turning diagnostics on/off 92
U
USCO pin designations 29
Users
deleting 107
moving 61
moving, adding, swapping 107
swapping 62
V
Voice stations, programming 52
Volume
backing up, restoring 102
displaying information 102
enabling, disabling access 103
formatting 104
mounting, dismounting 102
213
Technician’s Handbook
Notes:
214
E-Doc Tips
Advanced Graphical User Interface Example
How Do I Print a Procedure from the Infobase?
1. In the Table of Contents, select the check box of the section that you
want to print.
2. On the File menu, click Print.
3. Click the Print Document tab.
4. Click Section.
CAUTION: Do not click all or you will print the entire infobase.
5. Click OK.
How Do I Export a Section of the Infobase to a Word
Processing File?
1. In the Table of Contents, select the check box of the section that you
want to export.
2. On the File menu, click Export.
3. In the Save In list, select the save location.
4. In the File name box, type a name.
5. In the Save as type list, select a file type.
6. In the Export Range list, select Checked Branches.
7. Click Export.
E-Doc Tips
How Do I Get More Information?
The documentation CD-ROM contains all of the technical information in an
electronic file called an "infobase". Folio Views, the infobase viewer, has
powerful search capabilities that let you find information quickly and easily.
Once you've found the information that you need, you can read it online, print
sections, or export segments to word processing files.
How Do I Search the Entire Infobase?
1. Click
2. In the Query For box, type your search criteria.
3. Click OK.
To view the next hit, click
; to view the previous hit, click
.
How Do I Search a Section of the Infobase?
1. In the Table of Contents, select the check box of the section that you want
to search.
2.
3.
4.
5.
Click
In the Query For box, type your search criteria.
Ensure that the Checked branches check box is selected.
Click OK.
To view the next hit, click
; to view the previous hit, click
.