INSTALLATION GUIDE
Dual Fuel Ranges
Contents
Important Note
Wolf Dual Fuel Ranges . . . . . . . . . . . . . . . . . . . . . . . . . 3
To ensure the safe and efficient use of Wolf equipment,
please take note of the following types of highlighted
information throughout this guide:
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Dual Fuel Range Specifications . . . . . . . . . . . . . . . . . . 5
Dual Fuel Range Installation . . . . . . . . . . . . . . . . . . . . 14
IMPORTANT NOTE highlights information that is
especially important.
Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
CAUTION signals a situation where minor injury or product
damage may occur if instructions are not followed.
Features and specifications are subject to change at any time
without notice. Visit wolfappliance.com/specs for the most
up-to-date information.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specified.
Wolf Dual Fuel Ranges
3
wolfappliance.com/specs
Dual Fuel Range Installation
IMPORTANT NOTE: This installation must be completed
by a qualified installer, service agency or gas supplier.
Wolf Dual Fuel Range
Read this entire installation guide prior to installation and
save for the local inspector’s reference. The homeowner
should keep this installation guide for future reference.
Serial Number
This appliance must be installed in accordance with
National Electrical Codes, as well as all state, municipal
and local codes. The correct voltage, frequency and
amperage must be supplied to the appliance from a dedicated, grounded circuit which is protected by a properly
sized circuit breaker or time delay fuse. The proper
voltage, frequency, and amperage ratings are listed on
the product rating plate.
Wolf dual fuel ranges are manufactured for use with
natural gas or LP gas. Check the product rating plate for
the type of gas for your specific model. If this appliance
does not correspond to your type of gas, contact your
authorized Wolf dealer.
Record the model and serial numbers before installing the
dual fuel range. Both numbers are listed on the product
rating plate, located on the bottom of the control panel
assembly, at the far right, just above the oven door. Refer
to the illustration below.
RATING PLATE
Location of rating plate.
Model Number
Safety Instructions
4
IMPORTANT INSTRUCTIONS
WHAT TO DO IF YOU SMELL GAS:
If the information in this guide is not followed
exactly, a fire or explosion may result, causing
property damage, personal injury or death.
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s
• Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
• Warranty service must be performed by a Wolf
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
authorized service center.
• Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
• All openings in the wall or floor where the range is to
be installed must be sealed.
• A ventilation hood is recommended for use with the
Wolf dual fuel range.
• In Massachusetts: Installations and repairs must be
performed by a qualified or licensed contractor,
plumber or gasfitter qualified or licensed by the
state, province, or region where this appliance is
being installed. Only use gas shut-off valves
approved for use within the state, province, or region
where this appliance is being installed. A flexible gas
connector, when used, must not exceed 3' (.9 m).
This range can tip. Injury to persons could result.
Install the anti-tip device provided with this range
according to instructions on page 14.
Dual Fuel Range Specifications
5
wolfappliance.com/specs
Dual Fuel Range Dimensions
30" (762) RANGE
36" (914) RANGE
48" (1219) RANGE
36 7/8"
36 7/8"
36 7/8"
(937)
HEIGHT TO
COOKING
SURFACE*
(937)
HEIGHT TO
COOKING
SURFACE*
(937)
HEIGHT TO
COOKING
SURFACE*
29 7/8" (759)
47 7/8" (1216)
357/8" (911)
29 1/2" (749)
27 1/2" (699)
9 1/4"
(235)
60" (1527) RANGE
55 7/8"
(1419)
20"
RISER
60 1/8" (1527)
36 7/8"
35 7/8"
(937)
HEIGHT TO
COOKING
SURFACE*
(911)
24 1/8" (613)
45 7/8"
25" (635)
(1165)
10"
RISER
26 1/8" (664)
40 7/8"
(1035)
5"
RISER
47" (1194)
*LEGS AND CASTERS ALLOW FOR
HEIGHT ADJUSTMENT UP TO 39" (991)
SIDE VIEW—ALL RANGES
Dual Fuel Range Specifications
6
Installation Requirements
VENTILATION
Failure to locate the range without the proper clearances will result in a fire hazard.
IMPORTANT NOTE: Caution must be used in planning the
proper installation of the Wolf dual fuel range to avoid fires
or damage to adjacent cabinetry or kitchen equipment.
Follow all minimum clearances to combustible surfaces
shown in the installation illustration for your specific model
on the following pages.
IMPORTANT NOTE: When installing against a combustible
surface, a minimum 10" (254) riser is required for a 36"
(914) dual fuel range with charbroiler or griddle and all
48" (1219) and 60" (1524) models.
Risers and other accessories are available through your
authorized Wolf dealer. To obtain local dealer information,
visit the find a showroom section of our website,
wolfappliance.com.
The dual fuel range must have an adequate supply of fresh
air to assure proper combustion and ventilation. The
location of the range should be away from strong draft
areas, such as windows, doors and strong heating vents
or fans. Do not obstruct the flow of air.
Due to the high volume of ventilation air required, a source
of outside replacement air is recommended. This is especially important for tightly sealed and insulated homes. A
qualified HVAC contractor should be consulted.
It is recommended that you use a Wolf pro ventilation
hood or hood liner with the dual fuel range. If the range is
to be installed without ventilation, a 36" (914) minimum
clearance, 44" (1118) for charbroiler, from countertop to
combustible materials above the range is required. Refer
to the installation illustrations on pages 10–13.
Dual Fuel Range Specifications
7
wolfappliance.com/specs
Electrical Requirements
Locate the electrical supply flush with back wall and within
the shaded area shown in the illustration for your specific
model on the following pages.
30" AND 36" DUAL FUEL RANGES
• Power supply: 240 / 208 V AC, 60 Hz with 30 amp
service.
• Maximum connected load: 5.2 kW.
• Total amps: 21 amps.
• Supply wire minimum size: L1, L2 and ground—
12 AWG, neutral—16 AWG.
48" AND 60" DUAL FUEL RANGES
• Power supply: 240 / 208 V AC, 60 Hz with 50 amp
service.
• Maximum connected load: 10.2 kW.
• Total amps: 42.5 amps.
• Supply wire minimum size: L1 and L2—8 AWG,
ground—10 AWG, neutral—12 AWG.
IMPORTANT NOTE: You must follow all National Electrical
Code regulations. In addition, be aware of local codes and
ordinances when installing your service.
IMPORTANT NOTE: Performance may be compromised if
the electrical supply is less than 240 volts.
WIRING DIAGRAM
The wiring diagram covering the control circuit is located
behind the control panel on top of the cavity insulation
retainer and under the control board.
Dual Fuel Range Specifications
8
Gas Supply Requirements
EXPLOSION HAZARD: Use a certified gas supply line
and install a gas shut-off valve. Securely tighten all gas
connections. Failure to follow these instructions can
result in explosion, fire or death.
IMPORTANT NOTE: The dual fuel range must be connected
to a regulated gas supply.
IMPORTANT NOTE: This installation must conform with
local codes and ordinances. In the absence of local
codes, installations must conform with the American
National Standard, National Fuel Gas Code.
The dual fuel range is equipped for use with natural or
liquid propane (LP) gas. It is design certified by the
Canadian Standards Association (CSA) for natural or LP
gases. The product rating plate, located on the bottom of
the control panel assembly, at the far right, just above the
oven door, has information on the type of gas that should
be used. Refer to the illustration below. If this information
does not agree with the type of gas available, check with
the local gas supplier.
A gas supply line of 3/4" rigid pipe must be provided to the
range. If local codes permit, a certified, 3' (.9 m) long,
1/2" or 3/4" ID flexible metal appliance connector is recommended to connect the range to the gas supply line. For
LP gas, piping or tubing size can be 1/2" minimum. LP gas
suppliers usually determine the size and materials used on
the system. The pipe coming out the back of the range
has 1/2" female threads. Pipe joint compounds, suitable for
use with natural or LP gas should be used.
Locate the gas supply within the shaded area shown in
the illustration for your specific model on the following
pages.
IMPORTANT NOTE: The supply line must be equipped
with an approved external gas shut-off valve located near
the range in an accessible location. Do not block access
to the shut-off valve. Refer to the illustration below.
Wolf natural gas ranges will function up to an altitude of
10,250' (3124 m) without any adjustment. LP gas ranges
will function up to 8,600' (2621 m) without adjustment.
If the installation exceeds these elevations, contact your
authorized Wolf dealer for a high altitude conversion kit.
Before connecting the gas supply, make sure all valves
are in a closed position. Do not connect the gas supply
to an appliance that shows any sign of damage.
RATING PLATE
SHUT-OFF VALVE
OPEN POSITION
TO APPLIANCE
Location of rating plate.
GAS SUPPLY
Gas shut-off valve.
Dual Fuel Range Specifications
9
wolfappliance.com/specs
Gas Supply Requirements
GAS MANIFOLD PRESSURE
• Natural Gas: Standard orifices are set for 5" (12.5 mb)
WC. A natural gas pressure regulator is installed.
• LP Gas: Standard orifices are set for 10" (25 mb) WC.
An LP gas pressure regulator is installed.
• Gas Supply Pressure: The maximum gas supply
pressure to the regulator should never exceed 14"
(34.9 mb) WC; .5 psi (3.5 kPa) for natural and LP gas.
The minimum line pressure is 7" (17.5 mb) WC for
natural gas and 11" (27.4 mb) WC for LP gas.
• Gas Pressure Regulator: To control and maintain a
uniform gas pressure in the gas manifold, the unit must
be used with a gas pressure regulator. The burner
orifices, etc. are sized for the gas pressure delivered by
the supplied regulator. Do not remove the regulator.
The maximum gas supply pressure to the regulator
should never exceed 14" (34.9 mb) WC; .5 psi (3.5 kPa).
Dual Fuel Range Specifications
10
30" (762) Dual Fuel Range
INSTALLATION
SIDE
CABINET
13" (330)
30" (762) TO 36" (914)
max
TO BOTTOM OF
VENTILATION HOOD**
18" (457) min
6" (152) TO
COMBUSTIBLE*
6" (152) TO
COMBUSTIBLE*
30" (762)
OPENING WIDTH
36" (914)
FLOOR TO
COUNTERTOP
36 7/8"
(937) TO
COOKING
SURFACE
10" (254)
8 1/2"
(216)
GAS
31/4" (83)
LOCATION OF GAS AND
ELECTRICAL EXTENDS
ON FLOOR
13" (330)
ELECTRICAL
*Minimum clearance from rough opening to combustible materials up to 18" (457) above countertop.
**36" (914) minimum clearance from countertop to combustible materials without ventilation hood.
NOTE: For island installations, 12" (305) minimum clearance from back of range to combustible rear wall above countertop.
3"
(76)
Dual Fuel Range Specifications
11
wolfappliance.com/specs
36" (914) Dual Fuel Range
INSTALLATION
SIDE
CABINET
13" (330)
30" (762) TO 36" (914)
max
TO BOTTOM OF
VENTILATION HOOD**
18" (457) min
6" (152) TO
COMBUSTIBLE*
6" (152) TO
COMBUSTIBLE*
36" (914)
OPENING WIDTH
36" (914)
FLOOR TO
COUNTERTOP
36 7/8"
(937) TO
COOKING
SURFACE
8 1/2"
15" (381)
GAS
(216)
31/4" (83)
LOCATION OF GAS AND
ELECTRICAL EXTENDS
ON FLOOR
19" (483)
ELECTRICAL
*Minimum clearance from rough opening to combustible materials up to 18" (457) above countertop.
**36" (914) minimum clearance, 44" (1118) for charbroiler, from countertop to combustible materials without ventilation hood.
NOTE: For island installations, 12" (305) minimum clearance from back of range to combustible rear wall above countertop.
3"
(76)
Dual Fuel Range Specifications
12
48" (1219) Dual Fuel Range
INSTALLATION
SIDE
CABINET
13" (330)
30" (762) TO 36" (914)
max
TO BOTTOM OF
VENTILATION HOOD**
18" (457) min
6" (152) TO
COMBUSTIBLE*
6" (152) TO
COMBUSTIBLE*
48" (1219)
OPENING WIDTH
36" (914)
FLOOR TO
COUNTERTOP
36 7/8"
(937) TO
COOKING
SURFACE
24" (610)
10" (254)
GAS
31/4" (83)
13" (330)
ELECTRICAL
*Minimum clearance from rough opening to combustible materials up to 18" (457) above countertop.
**36" (914) minimum clearance, 44" (1118) for charbroiler, from countertop to combustible materials without ventilation hood.
NOTE: For island installations, 12" (305) minimum clearance from back of range to combustible rear wall above countertop.
LOCATION OF GAS AND
ELECTRICAL EXTENDS
ON FLOOR
3"
(76)
Dual Fuel Range Specifications
13
wolfappliance.com/specs
60" (1527) Dual Fuel Range
INSTALLATION
SIDE
CABINET
13" (330)
30" (762) TO 36" (914)
max
TO BOTTOM OF
VENTILATION HOOD**
18" (457) min
6" (152) TO
COMBUSTIBLE*
6" (152) TO
COMBUSTIBLE*
60 1/4" (1530)
OPENING WIDTH
36" (914)
FLOOR TO
COUNTERTOP
36 7/8"
(937) TO
COOKING
SURFACE
31" (787)
10" (254)
GAS
31/4" (83)
13" (330)
ELECTRICAL
*Minimum clearance from rough opening to combustible materials up to 18" (457) above countertop.
**36" (914) minimum clearance, 44" (1118) for charbroiler, from countertop to combustible materials without ventilation hood.
NOTE: For island installations, 12" (305) minimum clearance from back of range to combustible rear wall above countertop.
LOCATION OF GAS AND
ELECTRICAL EXTENDS
ON FLOOR
3"
(76)
Dual Fuel Range Installation
Position the Range
The dual fuel range is very heavy. Use caution when
lifting and moving the unit.
IMPORTANT NOTE: Before moving the range, protect any
finished flooring to avoid damage to the floor. Secure oven
door(s) closed.
The dual fuel range has rolling casters in the rear which
allows for easy movement of the range by lifting the front
of the unit.
IMPORTANT NOTE: Do not lift the range by the oven door
handle(s). This will damage the oven door and hinges.
Move the dual fuel range into position near the installation
opening. Remove and discard all packing materials. Do
not discard the anti-tip bracket supplied with the range.
Refer to anti-tip bracket installation instructions.
14
Anti-Tip Bracket Installation
This range can tip. Injury to persons could result. Install
the anti-tip bracket supplied with the range.
Raise the unit to its desired height by adjusting the front
legs and rear casters. The legs and casters allow for
2 1/8" (54) height adjustment. Use a 3/4" socket to adjust
the rear casters. The front legs are adjusted by rotating the
bottom hexagonal portion of the leg.
Measure from the floor to the top of the range base flange
on the back of the unit. Add 1/8" (3) to this dimension and
mark the height on the wall at the back of the installation
opening. This will mark the bottom edge of the anti-tip
bracket. Approximately center the mark in the opening.
For double oven ranges, verify that the anti-tip bracket
does not interfere with the inner cavity supports.
If the oven door(s) need to be removed to position the
range, refer to oven door removal instructions.
Locate a stud on the wall at the back of the installation
opening, and install the anti-tip bracket at the same level
as this line.
If your installation requires a riser, it must be attached to
the range before installation. Refer to installation instructions packaged with the riser.
Push the range back into the opening, and ensure that the
rear base flange fits under the anti-tip bracket. Refer to
the illustration below.
IMPORTANT NOTE: The top of the range must be level.
Use the adjustable front legs and the rear casters to level
the range.
WALL
BACK OF
RANGE
ANTI-TIP
BRACKET
BASE FLANGE
HEIGHT TO BASE
FLANGE +1/8" (3)
Anti-tip bracket.
Dual Fuel Range Installation
15
wolfappliance.com/specs
Oven Door Removal
IMPORTANT NOTE: Remove the oven door(s) only if it is
necessary to fit the range through a tight doorway.
Removal may cause damage to the porcelain oven interior
or the door(s). Door removal should be done by a qualified
service technician or installer.
For removal, a hinge pin (supplied with the range) must be
inserted in the appropriate hinge arm. For each oven door,
only one hinge arm is spring loaded, requiring use of the
hinge pin for removal of the oven door. The hinge pin can
be found taped to the inside of the oven door.
For single oven ranges, the hinge pin will be inserted
through the hole in the right hinge arm (facing the range).
For double oven ranges, the spring hinges are located on
the outer edges of the unit. The left oven door will have
the spring hinge on the left side and the right oven door
will have the spring hinge on the right side. Refer to the
illustrations below.
OVEN DOOR REMOVAL
1) Remove the lower kickplate assembly to access the
lower hinge retainer mounting screws.
2) Open the oven door all the way and remove both upper
and lower hinge retainer mounting screws. The oven
gasket may have to be moved slightly to access the
bottom screws.
3) Move the hinge retainer plate forward slightly. The
hinge retainer plate will remain on the door hinge after
the mounting screws have been removed.
4) Insert the door hinge pin through the hole in the
appropriate hinge arm. Refer to the illustration below.
5) Carefully close the oven door to approximately 60°
from horizontal and lift the door away from the oven.
A slight racking motion may be required for removal.
Do not lift or carry the oven door by the door handle.
Failure to insert the hinge pin in the appropriate hinge
arm will cause damage to the range.
HINGE
RETAINER
PLATE
UPPER
MOUNTING
SCREW
HINGE
PIN
KICKPLATE
SPRING HINGE
SPRING HINGES
Oven door removal.
Single oven ranges.
Double oven ranges.
Dual Fuel Range Installation
Oven Door Removal
16
Electrical Connection
OVEN DOOR REINSTALLATION
1) Hold the oven door on both sides and position it with
door hinges aligned with openings in the oven frame.
2) Holding the oven door at an approximate 30° angle
from vertical, slide the hinges into the openings
until the bottom hinge arms drop fully into the hinge
receptacles.
3) Open the oven door to its fully opened position.
Remove the hinge pin from the appropriate hinge arm.
Refer to the illustration below.
4) Reinstall the hinge retainer plate with upper and lower
mounting screws.
5) Open and close the door completely to ensure that it is
properly installed.
6) Reinstall the lower kickplate assembly.
IMPORTANT NOTE: Fully extend the hinge claw which is
opposite the hinge pin location and insert into the hinge
pocket prior to inserting opposite side. This will ease the
installation of the oven door.
Verify that power is disconnected from the electrical
box before proceeding.
The terminal block on the rear of the range allows for a
3-wire or 4-wire installation. For a 4-wire installation, the
ground strap from the unit to the terminal block must be
cut. Two concentric knockouts are provided to allow for
permanent or cordset wiring of the unit.
THREE-WIRE ELECTRICAL SYSTEM
1) Where local codes permit, connect the ground appliance wire to the neutral (white) supply wire.
2) Connect the ground and white appliance wires to the
neutral (white) supply wire in the electrical box.
3) Connect the black appliance wire to the black (L1)
power supply wire in the electrical box.
4) Connect the red appliance wire to the red (L2) power
supply wire in the electrical box.
FOUR-WIRE ELECTRICAL SYSTEM
1) Separate the ground and white appliance wires.
HINGE
RETAINER
PLATE
UPPER
MOUNTING
SCREW
2) Connect the white appliance wire to the neutral (white)
supply wire in the electrical box.
3) Connect the black appliance wire to the black (L1)
power supply wire in the electrical box.
HINGE
PIN
4) Connect the red appliance wire to the red (L2) power
supply wire in the electrical box.
KICKPLATE
Oven door reinstallation.
5) Connect the ground appliance wire to the green/
ground house grounding wire in the electrical box.
Dual Fuel Range Installation
17
wolfappliance.com/specs
Gas Supply Connection
Range Removal
Before connecting the gas supply, make sure all valves
are in a closed position.
IMPORTANT NOTE: All connections to the gas piping must
be wrench-tightened. Do not make connections too tight,
this may crack the regulator and cause a gas leak. Do not
allow the pipes to turn when tightening fittings.
Assemble the flexible metal connector from the gas supply
pipe to the gas pressure regulator. Determine the fittings
required depending on the size of your gas supply line,
flexible metal connector and shut-off valve. Refer to the
illustration below. If a flexible metal connector is used, be
sure the tubing is not kinked. Open the shut-off valve in
the gas supply line. Wait a few minutes for the gas to
move through the line.
GAS LEAK TESTING
Brush a liquid detergent solution onto all gas connections
to test for leaks. Bubbles around connections will indicate
a gas leak. If a leak appears, close the gas shut-off valve
and adjust connections. Check for leaks again. Clean off
the detergent solution.
Never test for a gas leak with a match or other flame.
GAS PRESSURE
REGULATOR
SHUT-OFF
VALVE
ADAPTER
NIPPLE
ADAPTER
FLEXIBLE
METAL CONNECTOR
Gas supply line connection.
ELBOW
Disconnect the electrical and gas supply connections
before removing the range.
If removal of the dual fuel range is necessary for cleaning
or service, shut off the gas supply. Disconnect the electrical and gas supply connections to the range. Remove the
range. Reinstall in the reverse order and be sure to check
gas connections for leaks.
Refer to the Wolf dual fuel ranges use & care guide for
cleaning recommendations.
Dual Fuel Range Installation
18
Verify Range Operation
IMPORTANT NOTE: Prior to operating the range, be sure
to read the entire Wolf dual fuel ranges use & care guide
included with the range for important safety, service and
warranty information.
SURFACE BURNERS
Turn on the power supply to the range. Place the burner
cap on each burner base and position the burner grates
before lighting.
Surface burners of the dual fuel range use electronic
igniters. When the control knob is pushed in and turned to
the HIGH position, the system creates a spark to light the
burner. This sparking continues until the electronic ignition
senses a flame.
To check operation of the surface burners, push in and
turn each control knob to the HIGH position. The flame
should light within four seconds.
If the burners do not light properly, turn control knobs to
the OFF position. Check that burner caps are in the proper
position. Make sure electricity is being supplied to the
range and that the gas shut-off valve is in the open
position. Check operation again. If the burners still do not
light properly, contact a Wolf authorized service center.
IMPORTANT NOTE: Initial lighting of the surface burners
may take slightly longer, as air in the system must be
purged before gas can be supplied to the burner.
OVEN OPERATION
Install the oven rack guides onto the shoulder screws
located on the interior walls of the oven(s). Slide the oven
racks onto the rack guides.
The control panel should be closed. Touch and slightly
depress the flame graphic on the hidden control panel to
open.
Set the time of day by pressing the CLOCK touch pad,
scroll to the desired time by using the up or down arrows,
then touch ENTER. After setting the time, the hidden
control panel can be closed. The control panel does not
have to be open to operate the oven(s).
Select any of the ten cooking modes by using the oven
control knob bezel and turning to the desired mode. Once
the mode has been selected, the temperature can be
adjusted by turning the temperature readout knob—clockwise to increase temperature or counterclockwise to
decrease temperature. Verify that the oven is coming up to
temperature. For double oven ranges, verify operation for
both ovens. Refer to the Wolf dual fuel ranges use & care
guide for additional information.
IMPORTANT NOTE: A small amount of smoke and odor
may be noticed during the initial break-in period.
Service Information
19
wolfappliance.com/specs
Troubleshooting
Service Information
IMPORTANT NOTE: If the dual fuel range does not operate
properly, follow these troubleshooting steps:
If service is necessary, maintain the quality built into your
dual fuel range by calling a Wolf authorized service center.
• Verify that electrical power is being supplied to the
range.
To obtain the name and number of a Wolf authorized
service center, check the contact & support section of our
website, wolfappliance.com or call Wolf customer service
at 800-332-9513.
• Check electrical and gas supply connections to ensure
that the installation has been completed correctly.
• Check that the gas supply shut-off valve is in the open
position.
• Follow troubleshooting procedures outlined in the
Wolf dual fuel ranges use & care guide.
• If the range still does not operate properly, contact a
Wolf authorized service center. Do not attempt to repair
the range yourself. Wolf is not responsible for service
required to correct a faulty installation.
When calling for service, you will need the model and
serial numbers of the dual fuel range. Both numbers are
listed on the product rating plate, located on the bottom of
the control panel assembly, at the far right, just above the
oven door. Refer to the illustration below.
RATING PLATE
Location of rating plate.
The information and images in this guide are the copyright property of Wolf Appliance, Inc. Neither this guide nor any information or images contained herein
may be copied or used in whole or in part without the express written permission of Wolf Appliance, Inc. ©Wolf Appliance, Inc. all rights reserved.
Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc.
Sub-Zero, Sub-Zero & Design, Dual Refrigeration, Constant Care and The Living Kitchen are registered trademarks and service marks of Sub-Zero, Inc.
(collectively, the “Company Marks.”) All other trademarks or registered trademarks are property of their respective owners in the United States and other countries.
WOLF APPLIANCE, INC.
P. O. BOX 44848 MADISON, WI 53744
816980 REV-A
8/ 2010
WOLFAPPLIANCE.COM
800.332.9513