Sharp HT-SB600 Operating instructions

ENGLISH
MODEL
HT-SB600
SOUND BAR SYSTEM
OPERATION MANUAL
Thank you for purchasing this SHARP product. To obtain the best performance from this product, please
read this manual carefully. It will guide you in operating your SHARP product.
HT-SB600 Sound Bar system consisting of HT-SB600 (main unit), CP-SB600 (sound bar) and CP-SW600
(subwoofer).
TIMER
INPUT
HT-SB600
HDMI
ARC
3
2
1
TV
LINE
DIGITAL
2
1
2
1
TIMER
CLOCK
TUNER(BAND)
TUNING
DIMMER
MUTE
X-BASS
BASS/TREBLE
EQUALIZER
LEVEL
CENTER
LEVEL
SUBWOOFER
PRESET
VOL
VOL
PRESET
TV
VOL
INPUT
CHANNEL
Note:
This product is recommended for flat panel TV (LCD and plasma).
Accessories
Please confirm that only the following accessories are included.
AM Loop Antenna
(QANTLA004AWZZ)
Remote Control
(RRMCGA248AWSA)
Stand x 4
(GITAUA004AW01)
Wall Mount Angle x 2
(LANGKA167AWFW)
Pattern Paper
(TCAUHA025AWZZ)
Speaker Wire
(QCNWHA042AW01)
TINSEA352AWZZ
HT-SB600_Front EN.fm
FM Antenna
(92LFANT1535A)
Printed in Malaysia
10K R KI 1
2011January25
Special Notes
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820 of the National
Electrical Code that provides guidelines for proper
grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of
the building, as close to the point of cable entry as
practical.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols:
ENERGY STAR® Program Information
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of
uninsulated “dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
Products that have earned
the ENERGY STAR® are
designed to protect the
environment through
superior energy efficiency.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
ENERGY STAR® is a U.S. registered mark.
Manufactured under license under U.S. Patent
#: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,487,535 & other U.S. and worldwide patents issued &
pending. DTS and the Symbol are registered trademarks
& DTS Digital Surround and the DTS logos are
trademarks of DTS, Inc. Product includes software.
© DTS, Inc. All Rights Reserved.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
FOR YOUR RECORDS
For your assistance in reporting this unit in case of loss
or theft, please record below the model number and
serial number which are located on the rear of the unit.
Please retain this information.
Model number
Serial number
Date of purchase
Place of purchase
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
........................................................
........................................................
........................................................
........................................................
NOTE
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and
receiver.
● Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV
technician for help.
WARNING
FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by
the manufacturer could void the user’s authority to operate
this equipment.
E-1
2011 January 27
HT-SB600
HDMI, the HDMI Logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other
countries.
Important Safety Instructions
Electricity is used to perform many useful functions, but it
can also cause personal injuries and property damage if
improperly handled. This product has been engineered
and manufactured with the highest priority on safety.
However, improper use can result in electric shock and/or
fire. In order to prevent potential danger, please observe
the following instructions when installing, operating and
cleaning the product. To ensure your safety and prolong
the service life of this product, please read the following
precautions carefully before use.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
1
2
3
4
5
6
7
1
9
Important Safety Instructions (continued)
8) Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
Additional Safety Information
15) Power Sources - This product should be operated only
from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to
your home, consult your product dealer or local power
company. For product intended to operate from battery
power, or other sources, refer to the operating
instructions.
16) Overloading - Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
17) Object and Liquid Entry - Never push objects of any
kind into this product through openings as they may
touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid
of any kind on the product.
18) Damage Requiring Service - Unplug this product from
the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen
into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in
any way, and
f) When the product exhibits a distinct change in
performance - this indicates a need for service.
E-2
2011 January 27
HT-SB600
19) Replacement Parts - When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.
20) Safety Check - Upon completion of any service or
repairs to this product, ask the service technician to
perform safety checks to determine that the product is
in proper operating condition.
21) Wall or ceiling mounting - When mounting the product
on a wall or ceiling, be sure to install the product
according to the method recommended by the
manufacturer.
22) Power Lines - An outside antenna system should not
be located in the vicinity of overhead power lines or
other electric light or power circuits, or where it can fall
into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken
to keep from touching such power lines or circuits as
contact with them might be fatal.
23) Protective Attachment Plug - The product is equipped
with an attachment plug having overload protection.
This is a safety feature. See Instruction Manual for
replacement or resetting of protective device. If
replacement of the plug is required, be sure the service
technician has used a replacement plug specified by
the manufacturer that has the same overload
protection as the original plug.
24) Stand - Do not place the product on an unstable cart,
stand, tripod or table. Placing the product on an
unstable base can cause the product to fall, resulting
in serious personal injuries as well as damage to the
product. Use only a cart, stand, tripod, bracket or table
recommended by the manufacturer or sold with the
product. When mounting the product on a wall, be sure
to follow the manufacturer's instructions. Use only the
mounting
hardware
recommended
by
the
manufacturer.
1
2
3
4
5
6
7
8
9
For U.S. customer only
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the
"Product"), when ship in its original container, will be free from defective workmanship and materials, and agrees that it will,
at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent
at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below
nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or
other misuse, abnormal service or handling, or which has been altered or modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide
proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law.
ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE
LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those
described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and
exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described
herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the
Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.
In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused
by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any
way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion
of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
Model Specific Section
Your Product Model Number & Description:
HT-SB600 Sound Bar System
(Be sure to have this information available when you need
service for your Product.)
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
Additional Item(s) Excluded from Warranty Coverage
(if any):
Non-functional accessories, supplies, and consumable
items.
Where to Obtain Service:
At a Sharp Authorized Servicer located in the United States.
To find a location of the nearest Sharp Authorized Servicer,
call Sharp toll free at 1-800-BE-SHARP.
What to do to Obtain Service:
Ship prepaid or carry in your Product to a Sharp Authorized
Servicer. Be sure to have Proof of Purchase available. If
you ship the Product, be sure it is insured and packaged
securely.
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
1
2
3
4
5
6
7
1
9
E-3
2011 January 27
HT-SB600
Precautions
General
Volume control
● Please ensure that the equipment is positioned in a
well-ventilated area and ensure that there is at least
4" (10 cm) of free space along the sides, top and back
of the equipment.
4" (10 cm) 4" (10 cm)
4" (10 cm)
The sound level at a given volume setting depends on
speaker efficiency, location and various other factors. It is
advisable to avoid exposure to high volume levels, which
occurs while turning the unit on with the volume control
setting up high, or while continually listening at high
volumes.
Cooling fan
This unit is fitted with a cooling fan at the rear for improved
cooling. Do not cover the opening in this section with any
obstacles.
4" (10 cm)
● Use the unit on a firm, level surface free from vibration.
● Keep the unit away from direct sunlight, strong
●
●
●
●
●
●
●
●
●
magnetic fields, excessive dust, humidity and
electronic/electrical equipment (home computers,
facsimiles, etc.) which generate electrical noise.
Do not place anything on top of the unit.
Do not expose the unit to moisture, to temperatures
higher than 140°F (60°C) or to extremely low
temperatures.
If your system does not work properly, disconnect the
AC power cord from the AC outlet. Plug the AC power
cord back in, and then turn on your system.
In case of an electrical storm, unplug the unit for safety.
Hold the AC power plug by the head when removing it
from the AC outlet, as pulling the cord can damage
internal wires.
The AC power plug is used as a disconnect device and
shall always remain readily operable.
Do not remove the outer cover, as this may result in
electric shock. Refer internal service to your local
SHARP service facility.
This unit should only be used within the range of 41°F 95°F (5°C - 35°C).
SHARP is not responsible for damage due to improper
use. Refer all servicing to a SHARP authorised service
center.
Warning:
The voltage used must be the same as that specified on
this unit. Using this product with a higher voltage other
than that which is specified is dangerous and may result in
a fire or other type of accident causing damage. SHARP
will not be held responsible for any damage resulting from
use of this unit with a voltage other than that which is
specified.
E-4
2011 January 27
HT-SB600
Cooling fan
Caution:
● The unit will get warm while being used. Do not touch
the warm areas of the unit for prolonged periods to
avoid injuries.
● This unit is equipped with a special function which
protects the amplifier circuit from damages. When it is
activated, the sound switch is turned off. In this case,
set the unit to the stand-by mode and turn on again.
1
2
3
4
5
6
7
8
9
Controls and indicators
1
2
Front Panel
3
Reference page
1. Remote Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2. Information Display . . . . . . . . . . . . . . . . . . . . . . . 16
3. Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4. On/Stand-by Button . . . . . . . . . . . . . . . . . 16, 18, 22
5. Input Button . . . . . . . . . . . . . . . . . . . . . . . 12, 15, 17
6. Equalizer Button . . . . . . . . . . . . . . . . . . . . . . 16, 22
7. Volume Up/Down Button . . . . . . . . . . . . . . . . . . . 16
4
5
6
7
Display
1 2 3 4
5
AM FMST
X-BASS MUTING
7
8
AM FMST
X-BASS MUTING
DIGITAL
9
PL
6
10
DIGITAL
PL
Reference page
PCM
ARC
1. AM Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. FM Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3. FM Stereo Indicator . . . . . . . . . . . . . . . . . . . . . .
4. FM Stereo receiving Indicator . . . . . . . . . . . . . .
5. DTS Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . .
6. PCM Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . .
7. X-BASS Indicator . . . . . . . . . . . . . . . . . . . . . . . .
8. MUTING Indicator . . . . . . . . . . . . . . . . . . . . . . . .
9. Dolby Digital Indicator . . . . . . . . . . . . . . . . . . . .
10. Dolby Pro Logic II Indicator . . . . . . . . . . . . . . . .
11. Audio Return Channel Indicator . . . . . . . . . . . .
11
PCM
ARC
E-5
2011 January 27
HT-SB600
19
18
18
17
17
18
17
16
17
17
17
1
2
3
4
5
6
7
1
9
Controls and indicators (continued)
Rear Panel
1
2
3
4
Reference page
1. Digital Input Jack. . . . . . . . . . . . . . . . . . . . . . 13, 14
2. Line Input Jack . . . . . . . . . . . . . . . . . . . . . . . 13, 14
3. FM 75 Ohms Antenna Jack. . . . . . . . . . . . . . 11, 12
4. AM Antenna Ground Terminal . . . . . . . . . . . . . . 11
5. AM Loop Antenna Terminal . . . . . . . . . . . . . . . . 11
6. Front Speaker Terminal. . . . . . . . . . . . . . . . . . . . 11
7. Center Speaker Terminal . . . . . . . . . . . . . . . . . . 11
8. Subwoofer Terminal . . . . . . . . . . . . . . . . . . . . . . 11
9. HDMI (TV ARC) Output Jack . . . . . . . . . . . . . . . . 12
10. HDMI input Jack. . . . . . . . . . . . . . . . . . . . . . . . . . 12
11. Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
12. AC Power Cord. . . . . . . . . . . . . . . . . . . . . . . . . . . 11
9
10
11
5
6
7
12
8
The spec label (*)
1
2
3
4
5
6
7
8
9
The spec label illustration may be
different from the actual label used
(*) Label is located at the bottom of the unit
E-6
2011 January 27
HT-SB600
Controls and indicators (continued)
Sound Bar
FRONT VIEW
1
3
2
4
2
2
REAR VIEW
5
6
7
Reference page
5. Right Front Speaker terminal . . . . . . . . . . . . . . . .11
6. Center Speaker terminal . . . . . . . . . . . . . . . . . . . .11
7. Left Front Speaker terminal . . . . . . . . . . . . . . . . .11
1. Left Front Speaker
2. Bass Reflex Duct
3. Right Front speaker
4. Center Speaker
Subwoofer
FRONT VIEW
REAR VIEW
2
1
3
SUBWOOFER SYSTEM
Reference page
1. Bass Reflect Duct
2. Woofer
3. Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . 11
E-7
2011 January 27
HT-SB600
1
2
3
4
5
6
7
1
9
Controls and indicators (continued)
1
Remote Control
Reference page
2
HDMI
ARC
3
1
2
1
2
1
CLOCK
TIMER
TV
4
5
DIGITAL
1. Remote Control Transmitter . . . . . . . . . . . . . . . . 15
2. On/Stand-by Button. . . . . . . . . . . . . . . . . . . . 16, 18
3. TV ARC Button. . . . . . . . . . . . . . . . . . . . . . . . 12, 17
4. DIGITAL 1-2 Button . . . . . . . . . . . . . . . . . . . . 15, 17
5. CLOCK Button . . . . . . . . . . . . . . . . . . . . . . . . 16, 19
6. TUNING Up/Down Button . . . . . . . . . . . . . . . . . . 18
7. Dimmer Button. . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8. EQUALIZER Button . . . . . . . . . . . . . . . . . . . . . . . 16
9. X-BASS Button . . . . . . . . . . . . . . . . . . . . . . . . . . 17
10. Subwoofer Level Down Button. . . . . . . . . . . . . . 16
11. Subwoofer Level Up Button . . . . . . . . . . . . . . . . 16
12. Preset Up Button . . . . . . . . . . . . . . . . . . . . . . 18, 19
13. Volume Down Button. . . . . . . . . . . . . . . . . . . 16, 17
14. ENTER Button . . . . . . . . . . . . . . . . . . . . . 18, 19, 20
15. TV Operation Button . . . . . . . . . . . . . . . . . . . . 8, 20
16. HDMI 1-2-3 Button . . . . . . . . . . . . . . . . . . . . . 12, 17
17. Line 1-2 Button . . . . . . . . . . . . . . . . . . . . . . . 15, 17
18. TIMER Button. . . . . . . . . . . . . . . . . . . . . . . . . 19, 20
19. TUNER(BAND) Button . . . . . . . . . . . . . . . . . . 17, 18
20. MUTE/Speaker Output Selection Button . . . . . . 16
21. Bass/Treble Button . . . . . . . . . . . . . . . . . . . . . . . 17
22. Center Speaker Level Up Button . . . . . . . . . . . . 17
23. Center Speaker Level Down Button. . . . . . . . . . 17
24. Volume Up Button . . . . . . . . . . . . . . . . . . . . . 16, 17
25. Preset Down Button . . . . . . . . . . . . . . . . . . . 18, 19
16
3
17
LINE
2
18
6
7
8
9
10
DIMMER
TUNING
TUNER(BAND)
19
EQUALIZER
X-BASS BASS/TREBLE
MUTE
20
21
SUBWOOFER LEVEL
CENTER LEVEL
22
11
PRESET
23
12
VOL
VOL
24
13
14
25
PRESET
TV
15
INPUT
CHANNEL
VOL
TV Operation Buttons (Only SHARP TV):
On/Stand-by Sets the TV Input Select
Button
power to
Button (TV)
“ON” or
“STAND-BY”.
Volume Up
and Down
Buttons
1
2
3
4
5
6
7
8
9
Press the
button to
switch the
input source.
Turn up/down Channel Up Switch up/
the TV
and Down
down the TV
volume.
Buttons
channels.
Note:
Some models of SHARP TV may not be operable.
E-8
2011 January 27
HT-SB600
Speaker preparation
To mount the speaker on the wall
4 Screw the wall mount angle to the wall as shown in
Caution:
● Be very careful to prevent the speaker [ 4.41 lbs. (2.0 kg)]
from falling when mounting on the wall.
● Before mounting, check the wall strength. (Do not put
on the veneer plaster or whitewashed wall. The speaker
may fall.) If unsure, consult a qualified service
technician.
● Mounting screws are not supplied. Use appropriate
ones.
● Check all wall mount angle screws for looseness.
● Select a good location. If not, accidents may occur or
the speaker may get damaged.
● SHARP is not responsible for accidents resulting
from improper installation.
Driving screws
the illustration. (Total screw is 8 pieces)
Wall mount angle
Wall mount
angle
Wall
(screws x 4) surface
Wall surface
(screws x 4)
Wall
mount
angle
Wall surface
Note:
Make sure all screws are fully tightened. (screws are not
supplied)
Installing the speaker
SHARP designed the speakers so you may hang them on
the wall. Use proper screws (not supplied). See below for
size and type.
mount angle.
2 Slot the speaker into the wall mount angle.
3 Fix them securely.
1/8" (3.2 mm)
3/16"
(5 mm)
1 Align the wall mount slot at the speaker to the wall
3/8" (9 mm)
Wall surface
7/8" (Min. 22 mm)
Fixing wall mount angle
(Horizontal position)
1 Fix the pattern paper to the wall in horizontal
position as below.
509 mm
Wall surface 44 mm
29 mm
44 mm
29 mm
Falling prevention
Safety wires (not supplied) are useful to prevent the
speaker from falling off the table.
Pattern paper
2 Make a hole on the wall following the screw point
marks on the pattern paper by using a drill.
1-1/4" (32 mm)
3/8" (8-9 mm)
Wall surface
3 Fix a wall mount plug (not supplied) into the hole
using a hammer, until it is flush with the wall
surface.
1-1/4" (32 mm)
3/8" (8-9 mm)
Loop the safety wires (not supplied) into each hole as
shown and tie the safety wires to the LCD TV stand.
Wall surface
E-9
2011 January 27
HT-SB600
1
2
3
4
5
6
7
1
9
Placing the system
Installation image:
Placing the stand
Place the stand as shown.
TV
SUBWOOFER SYSTEM
SUBWOOFER
SYSTEM
Stand
SUBWOOFER SYSTEM
VCR
DVD player
Main Subwoofer
unit
Place the system as shown.
Remove the protective film covering the main unit and
subwoofer before turn on the system.
Notes:
● As the sound from the system is omni-directional, you can
place the speaker anywhere you like. However, it is
recommended to place it as close to the TV as possible.
● The front panel of the speaker is not removable.
Caution:
● Do not change the installation direction when the unit is
turned on.
● Do not stand or sit on the main unit and speakers as
you may be injured.
1
2
3
4
5
6
7
8
9
E-10
2011 January 27
HT-SB600
System connections
Make sure to unplug the AC power cord before making any connections.
Main unit
Subwoofer
FM antenna
Red
Green
White
AM loop
antenna
Sound Bar
AC outlet
AC 120 - 60 Hz
SPEAKERS
–
+
FRONT
INPUT
CENTER
SUB
WOOFER
Purple
Speaker and Subwoofer connection
Connect the wire without insulation tube to the minus (-)
terminal, and the wire with colored insulation tube to the
plus (+) terminal. Make sure to match the colored
insulation tube with terminal color before connection.
Purple
Caution
● Never mistake the FRONT, CENTER and the
SUBWOOFER terminals. The main unit or the
speakers may be damaged.
● If you use other speakers with an impedance lower than
that specified, the main unit may be damaged. Front
speakers: 4 ohms, Subwoofer: 4 ohms.
● Do not make a mistake when
SPEAKERS
connecting the right and the left
speakers. The right speaker is
R
the one on the right side when FRONT L
you face the unit.
CENTER
● Do not let the bare speaker SUBER
WOOF
wires touch each other.
INCORRECT
● Do not allow any objects to fall
into or to be placed in the bass
reflex duct.
● Do not stand or sit on the subwoofer/speakers. You may
be injured.
INPUT
–
+
INPUT
E-11
2011 January 27
HT-SB600
1
2
3
4
5
6
7
1
9
System connections (continued)
TV
Antenna connection
Supplied FM antenna:
Connect the FM antenna wire to the FM
75 OHMS jack and position the FM
FM
antenna wire in the direction where the antenna
strongest signal can be received.
DVD, Blu-ray
disc player or
similar
To HDMI (ARC) input
terminal
Supplied AM loop antenna:
Connect the AM loop antenna to the AM
and GND (Ground) terminals. Position the
AM loop antenna for optimum reception.
Place the AM loop on a shelf, etc., or
attach it to a stand or a wall with screws
(not supplied).
To HDMI output
terminal
To HDMI
output
terminal
Installing the AM loop antenna:
<Assembling> <Attaching to the wall>
Wall
To HDMI input
terminal
Screws (not supplied)
Note:
Placing the antenna on the unit or near the AC power cord
may cause noise pickup.
Place the antenna away from the unit for better reception.
Outdoor FM antenna
Use an outdoor FM antenna if you require better reception.
Consult your dealer.
Outdoor
75 ohms
FM
coaxial cable antenna
HDMI cables are not supplied
To select HDMI 1, 2, 3 or TV ARC function:
On main unit:
Press INPUT button repeatedly until
“HDMI1”, “HDMI2”, “HDMI3” or “TV
ARC” appears on the display.
On remote
Press HDMI1, HDMI2, HDMI3 or TV
control:
ARC button.
Notes:
● This unit supports HDMI which enables ARC (Audio
Return Channel) function.
● To enable ARC function make sure to use High Speed
Note:
When an outdoor FM antenna is used, disconnect the
supplied FM antenna wire.
HDMI Connection
Caution:
Turn off all other equipment before making this connection.
The illustration below shows the flows of the signals.
Audio and Video signal
TV
DVD/Blu-ray
Game console
Digital tuner
HDMI cable.
● This structure also needs TV that supports ARC
function.
● To listen to the sound from non-ARC-compatible TV,
connect the digital output from TV to this system digital
input terminal. (refer page 13)
● This unit can be operated (power on/off, volume up/
down or switch input source) via a TV or similar
component which supports HDMI CEC (Consumer
Electronics Control) function. If this does not work, it
does not mean this system is faulty. Refer to the
operation manual of the respective component on how
to activate the CEC function. Example: Go to the Menu
of the component to search and turn on the CEC
function. Different brands may have different naming for
the CEC function. For Sharp LCD TV, it is named as
AQUOS LINK.
● To watch 3D images, connect 3D-compatible TV and
video component (Blu-ray Disc player, etc.) to this
system.
Make sure to use High Speed HDMI cables and put on
the 3D glasses, otherwise 3D images may not be
viewed properly.
E-12
2011 January 27
HT-SB600
1
2
3
4
5
6
7
8
9
Audio connections to TVs, DVD players, VCRs, etc.
Other connection (without HDMI)
The illustration below shows the flows of audio and video signals.
Audio signal
Video signal
TV
DVD/Blu-ray
Disc Player
VCR/Game
console
Digital tuner, etc.
Notes:
● Refer to the operation manual of the equipment to be connected.
● Fully insert the plugs to avoid fuzzy pictures or noises.
Connecting a TV, etc.
Connect to the TV using an optical digital audio cable or an audio cable.
TV
To audio output terminals
To optical
digital audio
output terminal
Main unit
To LINE IN 1 input
terminal
Optical digital
audio cable
(commercially
available)
Audio cable
(commercially
available)
To LINE IN 2 input terminals
E-13
2011 January 27
HT-SB600
Audio signal
To DIGITAL IN 1
(optical) input
terminal
Audio signal
To HEADPHONE
terminal
1
2
3
4
5
6
7
1
9
Audio connections to TVs, DVD players, VCRs, etc. (continued)
Connecting a DVD player, etc.
Connect to the DVD player with an optical digital audio cable or an audio cable.
To audio output
terminals
Blu-Ray/DVD Player/Digital tuner
To optical digital
audio output
terminal
To the TV (video)
Audio signal
Optical digital audio
cable (commercially
available)
Audio signal
To coaxial digital
audio output
terminal
Coaxial digital
audio cable
(commercially
available)
Main unit
To DIGITAL IN
1 (optical)
input terminal
To DIGITAL IN 2
(coaxial) terminal input
Audio cable
(commercially
available)
To LINE IN 2 input terminals
Note:
Connect the DVD video cable directly to the TV (refer to the operation manual for the DVD player).
Connecting a VCR, etc.
Connect to the VCR with an audio cable.
VCR
To audio output
terminals
To the TV
(video)
Main unit
Audio signal
To LINE IN 2
input terminal
Audio cable
(commercially
available)
Note:
Connect the VCR video cable directly to the TV (refer to the operation manual for the VCR player).
E-14
2011 January 27
HT-SB600
1
2
3
4
5
6
7
8
9
Remote Control (continued)
Audio connections to TVs, DVD
players, VCRs, etc. (continued)
To select DIGITAL IN 1 (optical input) or DIGITAL IN 2
(coaxial input) function:
On main unit: Press INPUT button repeatedly until
“DIGITAL 1” or “DIGITAL 2” appears on the
display.
On remote
Press the “DIGITAL 1” or “DIGITAL 2”
control:
button.
To select LINE IN 1 or LINE IN 2 function:
On main unit: Press INPUT button repeatedly until
“LINE 1” or “LINE 2” appears on the
display.
On remote
Press the “LINE 1” or “LINE 2” button.
control:
Notes concerning use:
● Replace the batteries if the operating distance is
reduced or if the operation becomes erratic.
● Periodically clean the transmitter on the remote control
and the sensor on the unit with a soft cloth.
● Exposing the sensor on the unit to strong light may
interfere with operation. Change the lighting or the
direction of the unit.
● Keep the remote control away from moisture, heat,
shock, and vibrations.
Test of the remote control
Point the remote control directly at the remote sensor on
the main unit.
The remote control can be used within the range
shown below:
Remote Control
Battery installation
Remote sensor
Use 2 “AAA” size batteries (UM/SUM-4, R3, HP-16 or
similar). Batteries are not included.
Plastic film covering can be removed or peeled off.
1 Open the battery cover.
2 Insert the batteries according to the direction
indicated in the battery compartment.
When inserting or removing the batteries, push them
toward the
battery terminals.
3 Close the battery cover.
HDMI
TV
E-15
HT-SB600
15° 15°
ARC
Caution:
● Replace all old batteries with new ones at the same
time.
● Do not mix old and new batteries.
● Remove the batteries if the unit will not be used for a
long period of time. This will prevent potential damage
due to battery leakage.
● Do not use rechargeable batteries (nickel-cadmium
battery, etc.).
● Installing the batteries incorrectly may cause the unit to
malfunction.
● Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat such as sunshine, fire or
the like.
2011 January 27
8" - 20"
(0.2 m - 6 m)
1
2
3
1
2
3
4
5
6
7
1
9
General control
Volume control
Main unit operation:
Press the VOLUME + button to
increase the volume and the
00 01 02 ..... 99 100
VOLUME – button for
decreasing.
Remote control operation:
Press the VOL + button to increase the volume and the
VOL – button to decrease the volume.
HDMI
ARC
1
TV
2
DIGITAL
1
2
CLOCK
TIMER
DIMMER
EQUALIZER
3
LINE
1
TUNING
2
TUNER(BAND)
X-BASS BASS/TREBLE
SUBWOOFER LEVEL
MUTE
CENTER LEVEL
PRESET
VOL
VOL
VOL
Muting
VOL
To turn the power on
Press the ON/STAND-BY button on the main unit or the
remote control.
● The power turns on. If the power does not turn on,
check whether the AC power cord is plugged in
properly.
To set the unit to stand-by mode:
Press the ON/STAND-BY button again on the main unit or
the remote control.
The volume is muted temporarily
when pressing the MUTE button
on the remote control. Press again
to restore the volume.
Note:
When the unit is turned off and back on again, muting is
canceled.
Equalizer
Press the EQ button on the main unit or EQUALIZER
button on the remote control repeatedly to select the
desired equalizer mode.
Display brightness control
Press the DIMMER button to adjust the brightness of the
display.
Dimmer 1
(Display is dim)
Dimmer 2
(Display gets dimmer)
Dimmer off
(Display is bright)
MUTING
MUSIC
(for standard sound effect)
CINEMA /GAME
(for cinema/game sound effect)
SPORT
(for sport broadcasting)
NEWS
(for news)
DOLBY VS
(Dolby Virtual Speaker)
Subwoofer level control
Clock display
Clock can be displayed
during power On or standby
mode.
Display clock:
Press the CLOCK button on
the remote control. The time
display will appear for about 5
seconds.
To cancel the time display manually press the clock
button again within 5 seconds.
Note:
If clock not previously set, “ADJUST” will be displayed for
a while. (Refer “setting the clock” on page 19)
Volume auto fade-in
If you turn off and on the unit with the volume set to 80 or
higher, the volume starts at 40 and fades in to the last set
level.
The subwoofer level can be
adjusted.
To increase the level, press
-5 -4 ..... 4 5
the SUBWOOFER LEVEL
+ button.
To decrease the level, press the SUBWOOFER LEVEL
– button.
Notes:
● When sound from the speaker is distorted, decrease
the subwoofer level.
● When changing the subwoofer level, the output level of
the Subwoofer is also changed.
Center speaker level control
The center speaker level can
be adjusted.
To increase the level, press
the CENTER LEVEL + button.
HT-SB600
-4 .....
4
5
To decrease the level, press the CENTER LEVEL –
button.
Speaker output selection (HDMI connection)
Press and hold MUTE button on the remote control until
“TV SPK” or “SB SPK” appear on the display to toggle
sound output between this unit or TV.
E-16
2011 January 27
-5
1
2
3
4
5
6
7
8
9
General control (continued)
Bass control
Audio Return Channel (ARC) (Audio
Return Channel submenu)
1. Press the BASS/TREBLE
button to select “BASS”.
2. Within 5 seconds, press the
VOLUME (+ or –) button to
adjust the bass.
The audio return channel (ARC) function enables an HDMI
ARC-capable TV to send the audio stream to the HDMI
OUT jack of the receiver. To use this function, you must
select the TV ARC input and your TV must supports the
ARC function.
Treble control
Dolby Virtual Speaker (DVS) sound mode
1. Press the BASS/TREBLE
button to select “TREBLE”.
2. Within 5 seconds, press the
VOLUME (+ or –) button to
adjust the treble.
The Dolby Virtual Speaker (DVS) creates virtual surrounds
comparable to the 5.1ch sound produced by the 3.1ch
speaker.
When setting DVS to “ON” for 2 channel stereo signals,
Dolby Pro Logic II brings out virtual sound effects through
the signals converted into 5.1ch.
X-Bass control
When the X-BASS button on the
remote control is pressed, the X-BASS
unit will enter the extra bass
X-BASS
mode which emphasizes the
bass frequencies, and X-BASS
indicator will appear. To cancel
the extra bass mode, press the
X-BASS or BASS/TREBLE
button.
Notes:
● Monaural signals do not generate surround effects.
● DVS equalizer effect may not be obtained depending
on signal types (the Dolby Virtual Speaker indicator
blinks). In this case, set the DVS mode to OFF.
DVS
Function
HDMI 1
HDMI 2
HDMI 3
TV ARC
DIGITAL 1
The Dolby Virtual Speaker creates multichannellike sound effects.
Compared with the cinema mode, the bass sound
level is slightly reduced.
The Dolby Pro Logic II indicator also lights up if
2ch sound signals are detected.
● The DVS can be turned OFF by selecting other preset
equalizer modes.
This product incorporates decoders supporting the Dolby
Digital system and DTS system.
AM
FM
FM ST
LINE 2
LINE 1
DIGITAL 2
On the main unit:
When pressing the INPUT button, the input source will
change. Press the INPUT button repeatedly to select
desired input source.
On remote control:
Press the LINE 1 or 2 button to select LINE IN 1 input or
LINE IN 2 input.
Press the DIGITAL 1 or 2 button to select DIGITAL IN 1
input or DIGITAL IN 2 input.
Press the HDMI 1 or 2 or 3 to select HDMI input.
Press the TUNER(BAND) button repeatedly to select tuner
function (FM ST/FM Mono/AM).
Press TV ARC button to select TV ARC.
Note:
The backup function will protect the memorized function
mode for a few hours should there be a power failure or the
AC power cord becomes disconnected.
Auto power on function:
When you press any function button on the remote control,
the unit will turn on.
Auto power off function:
The unit will automatically go to stand-by mode if:
1. No signal is detected within 20 minutes.
2. No reception of tuner broadcast signal within 20
minutes.
E-17
2011 January 27
HT-SB600
DTS (Digital
Theater
Systems)
One of the digital audio systems for
theatrical use. As the sound quality is
emphasized, you can enjoy the realistic
sound effect in the home theater system.
Lights up when detecting DTS signal.
Dolby Digital One of the digital audio systems for
theatrical use. You can also enjoy the
stereophonic effect in the home theater
system.
Lights up when detecting Dolby Digital
signal.
Dolby Pro
System expanding 2ch stereo sound to
Logic II
more spacious sound. When setting
Dolby Virtual speaker to “ON”, Dolby Pro
Logic II is activated to enjoy the stereo
sound effect.
Lights up when Dolby Pro Logic II is
activated.
PCM
This is a general term for digitally
(Pulse Code encoded audio signals on a CD or DVD.
Modulation) This unit lets you enjoy playback of digital
signals from sources such as CD or DVD.
The indicator lights up when a PCM
signal is detected.
1
2
3
4
5
6
7
1
9
Listening to the radio
Listening to the radio (continued)
Memorizing a station
You can store 40 FM stations in memory and recall them
at the push of a button. (Preset tuning)
HDMI
ARC
1
2
1
2
1
CLOCK
TIMER
TV
DIGITAL
DIMMER
EQUALIZER
3
LINE
TUNING
2
1 Perform steps 1 - 3 in “Tuning” on page 18.
TUNER(BAND)
X-BASS BASS/TREBLE
2 Press the ENTER button to enter the preset tuning
MUTE
saving mode.
TUNING
3 Within 5 seconds, press the PRESET (
or
)
buttons to select the preset channel number.
Store the stations in memory, in order, starting with
preset channel 1.
4 Within 5 seconds, press the ENTER button to
Note:
This product can receive FM stereo/FM monaural/AM
broadcasts.
store that station in memory.
Tuning
If the preset number indicators disappear before the
station is memorized, repeat the operation from step
2.
1 Press the ON/STAND-BY button to turn the power
on.
2 Press the INPUT button on the main unit or
5 Repeat steps 1 - 4 to set other stations, or to
TUNER(BAND) button on the remote control
repeatedly to select the desired frequency band
(FM Stereo/FM Mono/AM).
change a preset station.
When a new station is stored in memory, the station
previously memorized will be erased.
3 Press the (TUNING
or ) button to tune in to
the desired station.
Manual tuning:
Press the (TUNING
or ) button as many times as
required to tune in to the desired station.
Auto tuning:
When the (TUNING
or
) button is pressed for
more than 0.5 seconds, scanning will start
automatically and the tuner will stop at the first
receivable broadcast station.
Notes:
● When radio interference occurs, auto scan tuning may
stop automatically at that point.
● Auto scan tuning will skip weak signal stations.
● To stop the auto tuning, press the TUNING button
again.
Note:
The backup function protects the memorized stations for a
few hours should there be a power failure or the AC power
cord become disconnected.
To recall a memorized station
Press the PRESET (
or
) button for less than 0.5
seconds to select the desired station.
To erase entire preset memory
1. Hold the TUNER(BAND) button on the remote control
for 4 seconds or more.
2. While “CLEAR” is flashing, press the ENTER button.
To receive an FM stereo transmission:
● “
” will appear when an FM broadcast is in stereo.
● If the FM reception is weak, press the TUNER(BAND)
button to extinguish the “ST” indicator. The reception
changes to monaural, and the sound becomes clearer.
FM stereo mode indicator
FMST
FM stereo receiving indicator
E-18
2011 January 27
HT-SB600
1
2
3
4
5
6
7
8
9
Setting the clock (Remote Control only)
Timer operation (Remote Control only)
By setting the unit to the correct time, you can use it not
only as a clock but also for timer.
Setting the timer
In this example, the clock is set for the 12-hour (AM 12:00)
display.
SUBWOOFER LEVEL
CENTER LEVEL
PRESET
1 Press the CLOCK button. If clock is not set
VOL
“ADJUST” will blink. Within 5 seconds, press the
ENTER button.
VOL
PRESET
TV
2 Press the
or
button to select 12-hour or
24-hour display and then press the ENTER button.
“AM 12:00”
“AM 0:00”
“0:00”
The 12-hour display will appear
(AM 12:00 - PM 11:59)
The 12-hour display will appear
(AM 0:00 - PM 11:59)
The 24-hour display will appear
(0:00 - 23:59)
You can use the unit as an alarm clock by setting the timer.
Before setting timer:
1. Set the unit to the correct time (page 19).
If it is not set, you cannot use the timer function.
2. Prepare the sound source for playback.
3. Store radio stations (page 18).
1 Turn the power on and press the TIMER button.
Set the unit to the correct time if “STANDBY” does not
appear.
3 Press the
or
button to adjust the
hour and then press the
ENTER button.
2 Within 10 seconds, press the
or
button to
select “TIMER SET”, and press the ENTER button.
● Press the
or
button once to advance the time
by 1 hour. Hold it down to advance continuously.
● When the 12-hour display is selected, “AM” will
change automatically to “PM”.
3 Press the
4 Press the
4 Press the
or
button to adjust the hour and
then press the ENTER button.
or
button to adjust the minutes
and then press the ENTER button.
or button
to adjust the minutes
and then press the
ENTER button.
● Press the
or
button once to advance the time by
1 minute. Hold it down to advance continuously (5
minutes interval).
● The hour will not advance even if minutes advance
from “59” to “00”.
● The clock starts from “0” second (seconds are not
displayed).
● The time display disappears after approx. 5 seconds.
The start time is set and the finish time (1 hour later)
will be displayed automatically.
5 Set the time to finish as in steps 3 and 4.
6 Switch input with the
or
buttons, and then
press the ENTER button.
To confirm the time display:
Press the CLOCK button. The time display will appear for
about 5 seconds.
Note:
“ADJUST” will appear or time will be displayed if the
CLOCK button is pressed when the AC power supply is
restored after a power failure or unplugging the unit. If
incorrect, readjust the clock as follows.
To readjust the clock:
Perform “Setting the clock” from step 1. If “ADJUST” does
not appear, step 2 (for selecting the 12-hour or 24-hour
display) will be skipped.
To change the 12-hour or 24-hour display:
1. Clear all the programmed contents. [Refer to “Factory
reset, clearing all memory” on page 22 for details.]
2. Perform “Setting the clock” from step 1 onwards.
HDMI 1
TUNER
HT-SB600
HDMI 3
LINE 2
TV ARC
DIGITAL 1
LINE 1 DIGITAL 2
● When you select the tuner, select a station by
pressing the
or
button, and then press the
ENTER button.
● If a station has not been programmed, “NOPRESET”
will be displayed.
7 Adjust the volume with the
or
button and
press the ENTER button.
Settings are displayed in order, and the unit will enter
the timer stand-by mode.
Caution:
This unit cannot set the timer of other equipment.
To perform the timer playback using other equipment, you
should also set the timer on the equipment separately.
E-19
2011 January 27
HDMI 2
1
2
3
4
5
6
7
1
9
Timer operation (Remote Control only) (continued)
After completing the setting
When the timer setting is
completed:
The unit is in the timer
playback stand-by mode.
TIMER
When the start time is
reached:
Unit starts automatically
and the volume
increases gradually.
The unit is operated by
the timer.
Timer LED indicator
flashes
When the finish time is reached:
The unit is set to the power stand-by mode
automatically.
To check the timer setting:
1. While in the timer playback stand-by mode, press the TIMER
button.
2. Within 10 seconds, press the
or
button to select “TIMERCAL”,
and press the ENTER button.
The unit returns to the timer playback stand-by mode after the setting
contents are displayed in order.
Canceling the timer playback:
Timer playback is canceled by turning the power on while in the timer
playback stand-by mode. The same operation can be performed in the
following procedure without turning the power on.
1. Press the TIMER button. “TIMEROFF” will appear.
2. Within 10 seconds, press the ENTER button. Timer playback will be
canceled (the contents of the setting will not be canceled.)
Reusing the timer:
Using the same setting;
The timer setting will be memorized once it is entered. To reuse the
same setting, perform the following operations.
1. Turn the power on and press the TIMER button. “STANDBY” will
appear. If it does not appear, set the unit to the correct time.
2. Within 10 seconds, press the ENTER button. After the setting
contents are displayed in order, the unit is set to the timer playback
stand-by mode.
Changing the setting;
Turn the power on, and repeat the operation from step 1 in “Setting
the timer” (page 19).
The timer setting is canceled.
Operating the TV with the remote control
You can operate Sharp TVs with this system’s remote
control.
Other operable button
Input Select Button
Watching TV
Point the remote control at the TV.
1 Press the TV ON/STAND-BY button to turn on the
TV.
2 Pressing the TV CH
or
button enables TV
channel switching.
3 Press the TV VOL. + or - button to adjust the TV
volume.
E-20
2011 January 27
HT-SB600
1
2
3
4
5
6
7
8
9
Troubleshooting chart
Many potential problems can be resolved by the owner without
calling a service technician.
If something is wrong with this product, check the following before
calling your authorized SHARP dealer or service center.
Remote control
Symptom
● The remote control
General
does not operate
properly.
Symptom
● No sound is heard.
Possible cause
●
●
●
●
● The sound from
subwoofer is not well
balanced.
● Move the speaker away
● Is the unit unplugged?
● The protection circuit may
mode and then turn it back
on.
● Depending on the TV and
Tuner
Symptom
● The radio makes
Video component, 3D
images may not be
displayed.
Check the operation
manual of the respective
component.
● HDMI cable not support 3D
image.
HT-SB600
Possible cause
● Is the unit placed near the
TV or computer?
● Is the FM antenna or AM
loop antenna placed
properly? Move the
antenna away from the AC
power cord if it is located
nearby.
Sudden temperature changes, storage or operation in an
extremely humid environment may cause condensation
inside the cabinet or on the transmitter on the remote
control. Condensation can cause the unit to malfunction. If
this happens, leave the power on until normal playback is
possible (about 1 hour). Wipe off any condensation on the
transmitter with a soft cloth before operating the unit.
When this product is subject to strong external interference
(mechanical shock, excessive static electricity, abnormal
supply voltage due to lightning, etc.) or if it is operated
incorrectly, it may malfunction.
E-21
2011 January 27
unit plugged in?
● Is the battery inserted?
If problem occurs during operation
be activated. Unplug and
plug in the power cord
again after 5 minutes or
more.
displayed on the TV.
● Is the AC power cord of the
Condensation
from any computers or
mobile phones.
● The power is not
● 3D images not
turned on with the
remote control.
connected correctly?
Connect the HDMI cable
correctly and then perform
the reset procedure.
● Set the unit to the stand-by
turned on.
● The unit cannot be
unusual noises
continuously.
● When a button is
pressed, the unit
does not respond.
shining on the remote
sensor?
● Is the remote control for
another equipment used
simultaneously?
to the minimum or
maximum level?
● Noise is heard
during playback.
in front of the unit?
● Is there a strong light
● Is the subwoofer level set
● Is the HDMI cable
suddenly.
● Are there any obstructions
(selection) set properly?
Is the volume level set to
“0”?
Is muting activated?
Is HDMI compliant
equipment being used?
Is the HDMI cable
connected correctly?
Connect the HDMI cable
correctly and then perform
the reset procedure. (refer
page 22)
Do not connect or
disconnect an HDMI cable
while power is on. This
may lead to operation
problems.
● Power turns off
correct?
● Is the battery dead?
● Is the distance or angle
incorrect?
● Is the input signal
●
Possible cause
● Is the battery polarity
1
2
3
4
5
6
7
1
9
Troubleshooting chart (continued)
Error indicators and warnings
If such a problem occurs, do the following:
1. Set the unit to the stand-by mode and turn the power on
again.
2. If the unit is not restored in the previous operation, unplug
and plug in the unit again, and then turn the power on.
When you fail to perform operations properly, the following
messages are displayed on the unit.
Display
Meaning
● Malfunction of the surround
Factory reset, clearing all memory
circuit. Place the speaker away
from noise source and plug the
AC power cord into another AC
outlet. (*)
or
Make sure to disconnect all output and input cables
attached to the unit before performing the factory reset.
1. Press the ON/STAND-BY button to enter the power
stand-by mode.
2. While pressing the EQ button, press and hold the
ON/STAND-BY button until “RESET” appears.
or
or
● When there is no input signal.
●
Caution:
This operation will erase all data stored in memory
including clock, timer settings and tuner preset.
or
●
●
Maintenance
(Display blinks)
Cleaning the cabinet
●
●
Periodically wipe the cabinet with a soft cloth.
Caution:
● Do not use chemicals for cleaning (gasoline, paint
thinner, etc.). It may damage the cabinet finish.
● Do not apply oil to the inside of each component. It may
cause malfunctions.
Play back the connected
equipment.
Nonstandard signal. Cannot be
recognized.
Signals other than DOLBY
DIGITAL, DTS, Linear PCM
cannot be recognized.
Poor connection of the digital
audio input terminal.
Turn off the unit and check if the
cable is connected properly.
When the protection circuit is
activated.
Timer indicator
(blinks red)
● The cooling fan at the rear of the
(Shown for 2 seconds)
unit does not run.
Unplug the AC power cord and
check if foreign objects get
caught around the cooling fan. (*)
(*): Should the same message appear even if the speaker is
unplugged and plugged in, or is set to the stand-by mode
and on again, contact your local dealer where you
purchased the unit.
1
2
3
4
5
6
7
8
9
E-22
2011 January 27
HT-SB600
Specifications
As part of our policy of continuous improvement, SHARP
reserves the right to make design and specification
changes for product improvement without prior notice. The
performance specification figures indicated are nominal
values of production unit. There maybe some deviations
from these values in individual unit.
Main unit
Power source AC 120 - 60 Hz
Power
88 W
consumption
Dimension
Width: 4 - 1/2" (103 mm)
Height: 16 - 9/16" (421 mm)
Depth: 15 - 1/2" (395 mm)
Weight
12.34 lbs (5.6 kg)
Output power RMS: Total 400 watts
RMS:
Front Left/Right:
100 watts per channel into 4 ohms at
1 kHz, 10% total harmonic distortion
Center:
100 watts per channel into 4 ohms at
1 kHz, 10% total harmonic distortion
Subwoofer:
100 watts per channel into 4 ohms at
100 Hz, 10% total harmonic distortion
FTC:
Front:(Left/Right/Center):
Minimum 80 watts per channel into
4 ohms at 120 Hz to 20 kHz, 1% total
harmonic distortion
Subwoofer:
Minimum 80 watts per channel into
4 ohms at 100 Hz, 1% total harmonic
distortion
Output
terminal
Input
terminal
HDMI™ output: (audio/video support up
to 1080p) x 1
Analog input (LINE 1):
Stereo mini jack Ø 3.5 mm
100 mV / 47 kohms
Analog input (LINE 2):
RCA type x 1pair (L/R)
500 mV / 47 kohms
Coaxial digital input (DIGITAL 2):
RCA type x 1
Optical digital input (DIGITAL 1):
Square type x 1
HDMI input: (audio/video support up to
1080p) x 3
Tuner
Frequency
range
FM: 87.5 - 108.0 MHz
AM: 530 - 1,710 kHz
E-23
2011 January 27
HT-SB600
Soundbar (Speaker Right / Center / Left)
Type
Maximum
input power
Rated input
power
Impedance
Dimensions
Weight
Full Range speaker system
2 -1/2" (6.5 cm) speaker
200 W
100 W
4 ohms
Width: 36 - 1/4" (920 mm)
Height: 3 - 3/8" (85mm)
Depth: 3 - 1/8" (79 mm)
4.41 lbs. (2.0 kg)
Subwoofer
Type
Maximum
input power
Rated input
power
Impedance
Dimensions
Weight
Subwoofer system
6 - 5/16" (16 cm) woofer
200 W
100W
4 ohms
Width: 4 - 1/2" (114 mm)
Height: 16 - 9/16" (421 mm)
Depth: 15 - 1/2" (395 mm)
9.92 lbs. (4.5 kg)
1
2
3
4
5
6
7
1
9