EN
User manual
Refrigerator
ZBA7190A
2
Contents
Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Operation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2
3
4
4
4
Care and Cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5
What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6
Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7
Environmental concerns _ _ _ _ _ _ _ _ _ _ _ _ _ 10
Subject to change without notice
Safety information
In the interest of your safety and to ensure the correct use,
before installing and first using the appliance, read this
user manual carefully, including its hints and warnings.
To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are
thoroughly familiar with its operation and safety features.
Save these instructions and make sure that they remain
with the appliance if it is moved or sold, so that everyone
using it through its life will be properly informed on appliance use and safety.
For the safety of life and property keep the precautions of
these user's instructions as the manufacturer is not responsible for damages caused by omission.
Children and vulnerable people safety
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
• Keep all packaging well away from children. There is
risk of suffocation.
• If you are discarding the appliance pull the plug out of
the socket, cut the connection cable (as close to the
appliance as you can) and remove the door to prevent
playing children to suffer electric shock or to close
themselves into it.
• If this appliance featuring magnetic door seals is to
replace an older appliance having a spring lock (latch)
on the door or lid, be sure to make that spring lock
unusable before you discard the old appliance. This
will prevent it from becoming a death trap for a child.
2
General safety
Caution! Keep ventilation openings clear of
obstruction.
• The appliance is intended for keeping foodstuff and/or
beverages in a normal household as explained in this
instruction booklet.
• Do not use a mechanical device or any artificial means
to speed up the thawing process.
• Do not use other electrical appliances (such as ice
cream makers) inside of refrigerating appliances, unless they are approved for this purpose by the manufacturer.
• Do not damage the refrigerant circuit.
• The refrigerant isobutane (R600a) is contained within
the refrigerant circuit of the appliance, a natural gas
with a high level of environmental compatibility, which
is nevertheless flammable.
During transportation and installation of the appliance,
be certain that none of the components of the refrigerant circuit become damaged.
If the refrigerant circuit should become damaged:
– avoid open flames and sources of ignition
– thoroughly ventilate the room in which the appliance is situated
• It is dangerous to alter the specifications or modify this
product in any way. Any damage to the cord may cause
a short-circuit, fire and/or electric shock.
Warning! Any electrical component (power cord,
plug, compressor) must be replaced by a certified
service agent or qualified service personnel.
1. Power cord must not be lengthened.
2. Make sure that the power plug is not squashed or
damaged by the back of the appliance. A squashed
or damaged power plug may overheat and cause
a fire.
3. Make sure that you can come to the mains plug of
the appliance.
4. Do not pull the mains cable.
5. If the power plug socket is loose, do not insert the
power plug. There is a risk of electric shock or fire.
6. You must not operate the appliance without the
lamp cover1) of interior lighting.
• This appliance is heavy. Care should be taken when
moving it.
• Do not remove nor touch items from the freezer compartment if your hands are damp/wet, as this could
cause skin abrasions or frost/freezer burns.
• Avoid prolonged exposure of the appliance to direct
sunlight.
Daily use
• Do not put hot pot on the plastic parts in the appliance.
• Do not store flammable gas and liquid in the appliance,
because they may explode.
• Appliance's manufacturers storage recommendations
should be strictly adhered to. Refer to relevant instructions.
•
•
•
•
•
Report possible damages immediately to the place you
bought it. In that case retain packing.
It is advisable to wait at least four hours before connecting the appliance to allow the oil to flow back in
the compressor.
Adequate air circulation should be around the appliance, lacking this leads to overheating. To achieve
sufficient ventilation follow the instructions relevant to
installation.
Wherever possible the back of the product should be
against a wall to avoid touching or catching warm parts
(compressor, condenser) to prevent possible burn.
The appliance must not be located close to radiators
or cookers.
Make sure that the mains plug is accessible after the
installation of the appliance.
• Connect to potable water supply only.2)
Service
• Any electrical work required to do the servicing of the
appliance should be carried out by a qualified electrician or competent person.
• This product must be serviced by an authorized Service
Centre, and only genuine spare parts must be used.
Care and cleaning
Environment Protection
• Before maintenance, switch off the appliance and disconnect the mains plug from the mains socket.
• Do not clean the appliance with metal objects.
• Regularly examine the drain in the refrigerator for defrosted water. If necessary, clean the drain. If the drain
is blocked, water will collect in the bottom of the appliance.
This appliance does not contain gasses which could
damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be
discarded together with the urban refuse and rubbish. The
insulation foam contains flammable gases: the appliance
shall be disposed according to the applicable regulations
to obtain from your local authorities. Avoid damaging the
cooling unit, especially at the rear near the heat exchanger. The materials used on this appliance marked by the
are recyclable.
symbol
Installation
Important! For electrical connection carefully follow the
instructions given in specific paragraphs.
• Unpack the appliance and check if there are damages
on it. Do not connect the appliance if it is damaged.
Operation
Switching on
Insert the plug into the wall socket.
Turn the Temperature regulator clockwise to a medium
setting.
1) If the lamp cover is foreseen
2) If a water connection is foreseen
3
Switching off
Temperature regulation
•
•
•
•
The temperature is automatically regulated.
To operate the appliance, proceed as follows:
• turn the Temperature regulator toward lower settings
to obtain the minimum coldness.
• turn the Temperature regulator toward higher settings
to obtain the maximum coldness.
Important! If the ambient temperature is high or the
appliance is fully loaded, and the appliance is set to the
lowest temperatures, it may run continuously causing
frost to form on the rear wall. In this case the dial must be
set to a higher temperature to allow automatic defrosting
and therefore reduced energy consumption.
To turn off the appliance, turn the Temperature regulator
to the "O" position.
room temperature
how often the door is opened
the quantity of food stored
the location of the appliance.
A medium setting is generally the most suitable.
However, the exact setting should be chosen keeping in
mind that the temperature inside the appliance depends
on:
First use
Cleaning the interior
Before using the appliance for the first time, wash the
interior and all internal accessories with lukewarm water
and some neutral soap so as to remove the typical smell
of a brand-new product, then dry thoroughly.
Important! Do not use detergents or abrasive powders,
as these will damage the finish.
Daily use
Movable shelves
Positioning the door shelves
The walls of the refrigerator are equipped with a
series of runners so that
the shelves can be positioned as desired.
To permit storage of food
packages of various sizes,
the door shelves can be
placed at different heights.
Gradually pull the shelf in
the direction of the arrows
until it comes free, then
reposition as required.
Helpful hints and tips
Hints for energy saving
• Do not open the door frequently or leave it open longer
than absolutely necessary.
4
• If the ambient temperature is high and the Temperature
Regulator is set to low temperature and the appliance
is fully loaded, the compressor may run continuously,
causing frost or ice on the evaporator. If this happens,
set the Temperature Regulator toward warmer settings
to allow automatic defrosting and so a saving in electricity consumption.
Hints for fresh food refrigeration
To obtain the best performance:
• do not store warm food or evaporating liquids in the
refrigerator
• do cover or wrap the food, particularly if it has a strong
flavour
• position food so that air can circulate freely around it
Hints for refrigeration
Useful hints:
Meat (all types) : wrap in polythene bags and place on the
glass shelf above the vegetable drawer.
For safety, store in this way only one or two days at the
most.
Cooked foods, cold dishes, etc..: these should be covered
and may be placed on any shelf.
Fruit and vegetables: these should be thoroughly cleaned
and placed in the special drawer(s) provided.
Butter and cheese: these should be placed in special airtight containers or wrapped in aluminium foil or polythene
bags to exclude as much air as possible.
Milk bottles: these should have a cap and should be stored
in the bottle rack on the door.
Bananas, potatoes, onions and garlic, if not packed, must
not be kept in the refrigerator.
Care and Cleaning
Caution! Unplug the appliance before carrying out
any maintenance operation.
This appliance contains hydrocarbons in its cooling
unit; maintenance and recharging must therefore
only be carried out by authorized technicians.
Periodic cleaning
The equipment has to be cleaned regularly:
• clean the inside and accessories with lukewarm water
and some neutral soap.
• regularly check the door seals and wipe clean to ensure
they are clean and free from debris.
• rinse and dry thoroughly.
Important! Do not pull, move or damage any pipes and/
or cables inside the cabinet.
Never use detergents, abrasive powders, highly perfumed
cleaning products or wax polishes to clean the interior as
this will damage the surface and leave a strong odour.
casing of this appliance is only cleaned with warm water
with a little washing-up liquid added.
After cleaning, reconnect the equipment to the mains
supply.
Defrosting of the refrigerator
Frost is automatically eliminated from the evaporator of
the refrigerator compartment every time the motor compressor stops, during normal use. The defrost water
drains out through a trough into a special container at the
back of the appliance, over the motor compressor, where
it evaporates.
It is important to periodically clean the defrost water drain
hole in the middle of the refrigerator compartment channel
to prevent the water overflowing and dripping onto the
food inside. Use the special cleaner provided, which you
will find already inserted into the drain hole.
Clean the condenser (black grill) and the compressor at
the back of the appliance with a brush or a vacuum cleaner.
This operation will improve the performance of the appliance and save electricity consumption.
Important! Take care of not to damage the cooling system.
Many proprietary kitchen surface cleaners contain chemicals that can attack/damage the plastics used in this appliance. For this reason it is recommended that the outer
Periods of non-operation
When the appliance is not in use for long periods, take
the following precautions:
• disconnect the appliance from electricity supply
5
• remove all food
• defrost 3)and clean the appliance and all accessories
• leave the door/doors ajar to prevent unpleasant smells.
If the cabinet will be kept on, ask somebody to check it
once in a while to prevent the food inside from spoiling
in case of a power failure.
What to do if…
Warning! Before troubleshooting, disconnect the
mains plug from the mains socket.
Only a qualified electrician or competent person must do
the troubleshooting that is not in this manual.
Problem
The appliance does not operate.
The lamp does not operate.
Important! There are some sounds during normal use
(compressor, refrigerant circulation).
Possible cause
The appliance is switched off.
Solution
Switch on the appliance.
The mains plug is not connected to the Connect the mains plug to the mains
mains socket correctly.
socket correctly.
The appliance has no power. There is Connect a different electrical appliance
no voltage in the mains socket.
to the mains socket.
Contact a qualified electrician.
The lamp does not work.
The compressor operates continually.
Water flows on the rear plate of
the refrigerator.
The lamp is in stand-by.
Close and open the door.
The lamp is defective.
Refer to "Replacing the lamp".
The temperature is not set correctly.
Set a higher temperature.
The door is not closed correctly.
Refer to "Closing the door".
The door has been opened too frequently.
Do not keep the door open longer than
necessary.
The product temperature is too high.
Let the product temperature decrease to
room temperature before storage.
The room temperature is too high.
Decrease the room temperature.
During the automatic defrosting proc- This is correct.
ess, frost defrosts on the rear plate.
Water flows into the refrigerator. The water outlet is clogged.
Clean the water outlet.
Products prevent that water flows into Make sure that products do not touch
the water collector.
the rear plate.
Water flows on the ground.
The melting water outlet does not flow Attach the melting water outlet to the
in the evaporative tray above the com- evaporative tray.
pressor.
The temperature in the appliance The temperature regulator is not set
is too low.
correctly.
Set a higher temperature.
The temperature in the appliance The temperature regulator is not set
is too high.
correctly.
Set a lower temperature.
3) If foreseen.
6
Problem
Possible cause
Solution
The door is not closed correctly.
Refer to "Closing the door".
The product temperature is too high.
Let the product temperature decrease to
room temperature before storage.
Many products are stored at the same Store less products at the same time.
time.
There is no cold air circulation in the
appliance.
Replacing the lamp
Caution! Disconnect the plug from the mains
socket.
1. Remove the screw
from the lamp cover.
2. Remove the lamp
cover (refer to the
illustration).
3. Replace the used
lamp with a new
lamp of the same
4.
5.
6.
7.
Make sure that there is cold air circulation in the appliance.
power (the maximum power is shown on the lamp
cover).
Install the lamp cover.
Tighten the screw to the lamp cover.
Connect the plug to the mains socket.
Open the door. Make sure that the light comes on.
Closing the door
1. Clean the door gaskets.
2. If necessary, adjust the door. Refer to "Installation".
3. If necessary, replace the defective door gaskets. Contact the Service Center.
Technical data
Dimension of the recess
Height
1030 mm
Width
560 mm
Depth
550 mm
The technical information are situated in the rating plate
on the internal left side of the appliance and in the energy
label.
Installation
Caution! Read the "Safety Information" carefully for
your safety and correct operation of the appliance
before installing the appliance.
Positioning
Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the
rating plate of the appliance:
7
Climate
class
The appliance must be earthed. The power supply cable
plug is provided with a contact for this purpose. If the
domestic power supply socket is not earthed, connect the
appliance to a separate earth in compliance with current
regulations, consulting a qualified electrician.
The manufacturer declines all responsibility if the above
safety precautions are not observed.
This appliance complies with the E.E.C. Directives.
Ambient temperature
SN
+10°C to + 32°C
N
+16°C to + 32°C
ST
+16°C to + 38°C
T
+16°C to + 43°C
Electrical connection
Before plugging in, ensure that the voltage and frequency
shown on the rating plate correspond to your domestic
power supply.
Door reversibility
On the opposite side:
• Install the lower pin.
• Install the door.
• Tighten the spacer and
tighten the upper pin.
The door of the appliance
opens to the right. If you
want to open the door to the
left, do these steps before
you install the appliance:
• Loosen the upper pin
and remove the spacer.
• Remove the upper pin
and the door.
Ventilation requirements
The airflow behind the appliance must be sufficient.
• Remove the door.
• Loosen the lower pin.
Installing the appliance
50 mm
Caution! Make sure that the mains cable can move
freely.
min.
200 cm2
Do the following steps:
min.
200 cm2
8
2
I
4mm
1
44mm
I
Install the appliance in the
niche.
Push the appliance in the
direction of the arrows (1)
until the upper gap cover
stops against the kitchen
furniture. Make sure that
the distance between the
appliance and the cupboard front-edge is 44 mm.
Push the appliance in the
direction of the arrows (2)
against the cupboard on the
opposite side of the hinge.
Make sure that the clearance between the appliance
and the cupboard is 4 mm.
Adjust the appliance in the Attach the appliance to the Push the sealing strip beniche.
niche with 4 screws.
tween the appliance and the
The lower hinge cover (in
adjacent cabinet.
the accessories bag) makes
sure that the distance between the appliance and the
kitchen furniture is correct.
Open the door. Put the lower hinge cover in position.
ca. 50 mm
Ha
D
Hb
C
21 mm
E
E
Remove the correct part
from the hinge cover (E).
Make sure to remove the
part DX, in the case of right
hinge, SX in opposite case.
90°
Hc
90°
Hd
Attach the covers (C, D) to Disconnect the parts (Ha),
the lugs and the hinge
(Hb), (Hc) and (Hd).
holes.
Attach the hinge covers (E)
to the hinge.
ca. 50 mm
21 mm
Install the part (Ha) on the
inner side of the kitchen
furniture.
9
8 mm
8 mm
Ha
Ha
Hc
K
Ha
Hb
Push the part (Hc) on the
part (Ha).
Open the appliance door
and the kitchen furniture
door at an angle of 90°.
Insert the small square (Hb)
into guide (Ha).
Put together the appliance
door and the furniture door
and mark the holes.
Remove the brackets and
mark a distance of 8 mm
from the outer edge of the
door where the nail must be
fitted (K).
Hb
Place the small square on
the guide again and fix it
with the screws supplied.
Align the kitchen furniture
door and the appliance
door by adjusting the part
Hb.
Hb
Hd
Press the part (Hd) on the
part (Hb).
Do a final check to make sure that:
• All screws are tightened.
• The magnetic sealing strip is attached tightly to the
cabinet.
Important! If the ambient temperature is low (for example,
in the Winter), the size of the gasket decreases. The size
of the gasket increases when the ambient temperature
increases.
Environmental concerns
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it should be taken to the
appropriate collection point for the recycling of electrical
and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
10
negative consequences for the environment and human
health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed
information about recycling of this product, please
contact your local council, your household waste disposal
service or the shop where you purchased the product.
11
www.zanussi.com
212719211-00-16112009