NPort S8458 Series User`s Manual

NPort S8458 Series User’s Manual
First Edition, May 2011
www.moxa.com/product
© 2011 Moxa Inc. All rights reserved.
NPort S8458 Series User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2011 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Moxa China (Shanghai office)
Toll-free: 1-888-669-2872
Toll-free: 800-820-5036
Tel:
+1-714-528-6777
Tel:
+86-21-5258-9955
Fax:
+1-714-528-6778
Fax:
+86-21-5258-5505
Moxa Europe
Moxa Asia-Pacific
Tel:
+49-89-3 70 03 99-0
Tel:
+886-2-8919-1230
Fax:
+49-89-3 70 03 99-99
Fax:
+886-2-8919-1231
Table of Contents
1.
Introduction ...................................................................................................................................... 1-1
Overview ........................................................................................................................................... 1-2
Industrial Communications and Automation .................................................................................... 1-2
Industrial vs. Commercial ............................................................................................................. 1-2
Informative vs. Passive ................................................................................................................ 1-2
Package Checklist ............................................................................................................................... 1-2
Product Features ................................................................................................................................ 1-3
Product Specifications ......................................................................................................................... 1-3
General Specifications .................................................................................................................. 1-3
Device Server Specifications ......................................................................................................... 1-4
Ethernet Switch Specifications ...................................................................................................... 1-5
2.
Getting Started.................................................................................................................................. 2-1
Panel Layout ...................................................................................................................................... 2-2
Dimensions ........................................................................................................................................ 2-3
NPort S8455 series ...................................................................................................................... 2-3
NPort S8458 series ...................................................................................................................... 2-4
Connecting the Hardware..................................................................................................................... 2-4
Wiring Requirements ................................................................................................................... 2-5
Connecting the Power .................................................................................................................. 2-5
Connecting to the Network ........................................................................................................... 2-6
Connecting to a Serial Device ....................................................................................................... 2-6
LED Indicators ............................................................................................................................ 2-6
Adjustable Pull High/low Resistors and Terminators for the RS-485 Port (NPort S8455 series only) ........ 2-6
Wiring the Relay Contact .............................................................................................................. 2-7
Wiring the Digital Inputs .............................................................................................................. 2-7
3.
Initial IP Address Configuration ........................................................................................................ 3-1
Static and Dynamic IP Addresses .......................................................................................................... 3-2
Factory Default IP Address ................................................................................................................... 3-2
Configuration Options.......................................................................................................................... 3-2
Web Console............................................................................................................................... 3-2
ARP ........................................................................................................................................... 3-2
Telnet Console ............................................................................................................................ 3-3
Serial Console ............................................................................................................................. 3-6
4.
Choosing the Serial Operation Mode ................................................................................................. 4-1
Overview ........................................................................................................................................... 4-2
Real COM Mode .................................................................................................................................. 4-2
RFC2217 Mode ................................................................................................................................... 4-3
TCP Server Mode ................................................................................................................................ 4-3
TCP Client Mode ................................................................................................................................. 4-3
UDP Mode .......................................................................................................................................... 4-4
Disabled Mode .................................................................................................................................... 4-4
5.
Basic Settings and Device Server Configuration ................................................................................ 5-1
Opening Your Browser ......................................................................................................................... 5-2
Basic Settings .................................................................................................................................... 5-4
General Settings ......................................................................................................................... 5-4
Time Settings ............................................................................................................................. 5-5
Network Settings......................................................................................................................... 5-6
Serial Settings .................................................................................................................................... 5-8
Operation Modes ......................................................................................................................... 5-8
Serial Parameters ...................................................................................................................... 5-24
Serial ToS Settings .................................................................................................................... 5-26
6.
Switch Featured Functions ................................................................................................................ 6-1
Ethernet Settings ................................................................................................................................ 6-2
Port Settings............................................................................................................................... 6-2
Port Trunking .............................................................................................................................. 6-3
Communication Redundancy ......................................................................................................... 6-4
STP/RSTP ........................................................................................................................................ 6-14
The STP/RSTP Concept .............................................................................................................. 6-14
Configuring STP/RSTP ................................................................................................................ 6-18
Configuration Limits of STP/RSTP ................................................................................................ 6-19
Bandwidth Management .................................................................................................................... 6-20
Using Bandwidth Management .................................................................................................... 6-20
Configuring Bandwidth Management ............................................................................................ 6-20
Line Swap Fast Recovery ................................................................................................................... 6-21
Using Line-Swap-Fast-Recovery .................................................................................................. 6-21
Configuring Line-Swap Fast Recovery .......................................................................................... 6-21
Ethernet Advanced Settings ............................................................................................................... 6-21
Ethernet Traffic Prioritization ...................................................................................................... 6-21
The Traffic Prioritization Concept ................................................................................................. 6-22
Configuring Ethernet Traffic Prioritization ..................................................................................... 6-23
Virtual LAN ...................................................................................................................................... 6-26
Using Virtual LAN ...................................................................................................................... 6-26
The Virtual LAN (VLAN) Concept .................................................................................................. 6-26
Configuring Virtual LAN .............................................................................................................. 6-30
Multicast Filtering ............................................................................................................................. 6-31
Using Multicast Filtering ............................................................................................................. 6-31
The Concept of Multicast Filtering ................................................................................................ 6-31
Configuring IGMP Snooping ........................................................................................................ 6-34
IGMP Snooping Settings ............................................................................................................. 6-34
Configuring GMRP...................................................................................................................... 6-36
Set Device IP ................................................................................................................................... 6-36
Using Set Device IP ................................................................................................................... 6-36
Configuring Set Device IP ........................................................................................................... 6-37
System Management......................................................................................................................... 6-39
Misc. Network Settings ............................................................................................................... 6-39
SysLog Server .................................................................................................................................. 6-40
Using Syslog ............................................................................................................................. 6-40
Local User Database .................................................................................................................. 6-41
Port Access Control ........................................................................................................................... 6-42
Configuring Static Port Lock ........................................................................................................ 6-43
Configuring IEEE 802.1X ............................................................................................................ 6-44
Auto Warning Settings ............................................................................................................... 6-45
Configuring E-Mail Alert ..................................................................................................................... 6-45
Configuring SNMP ............................................................................................................................. 6-47
SNMP Read/Write Settings.......................................................................................................... 6-48
E-mail Event Settings ................................................................................................................ 6-49
SNMP Trap ............................................................................................................................... 6-51
Relay Alarm Settings ................................................................................................................. 6-52
System Log Settings .................................................................................................................. 6-53
Maintenance .................................................................................................................................... 6-55
Console Settings ....................................................................................................................... 6-55
Ping ......................................................................................................................................... 6-55
Update System Files from Local PC .............................................................................................. 6-56
Load Factory Default .................................................................................................................. 6-56
Change Password ...................................................................................................................... 6-57
Mirror Port Settings ................................................................................................................... 6-58
TFTP Settings............................................................................................................................ 6-58
Dip Switch Settings ................................................................................................................... 6-59
System Monitoring ............................................................................................................................ 6-61
Serial Status ............................................................................................................................. 6-61
System Status .......................................................................................................................... 6-63
Ethernet Status ......................................................................................................................... 6-64
Restart ............................................................................................................................................ 6-69
Restart System ......................................................................................................................... 6-69
Restart Serial Port ..................................................................................................................... 6-69
7.
Software Installation/Configuration ................................................................................................. 7-1
Overview ........................................................................................................................................... 7-2
NPort Windows Driver Manager ............................................................................................................ 7-2
Installing NPort Windows Driver Manager ....................................................................................... 7-2
Using NPort Windows Driver Manager ............................................................................................ 7-5
NPort Search Utility........................................................................................................................... 7-12
Installing NPort Search Utility ..................................................................................................... 7-12
Configuring NPort Search Utility .................................................................................................. 7-14
Linux Real TTY Drivers ...................................................................................................................... 7-16
Basic Procedures ....................................................................................................................... 7-16
Hardware Setup ........................................................................................................................ 7-16
Installing Linux Real TTY Driver Files ........................................................................................... 7-16
Mapping TTY Ports ..................................................................................................................... 7-17
Mapping tty ports manually ........................................................................................................ 7-17
Removing Mapped TTY Ports ....................................................................................................... 7-17
Removing Linux Driver Files........................................................................................................ 7-18
The UNIX Fixed TTY Driver ................................................................................................................. 7-18
Installing the UNIX Driver........................................................................................................... 7-18
Configuring the UNIX Driver ....................................................................................................... 7-19
Modify the configuration:............................................................................................................ 7-19
Device naming rule .................................................................................................................... 7-19
Starting moxattyd ..................................................................................................................... 7-19
Adding an additional server ........................................................................................................ 7-19
A.
Pinouts and Cable Wiring .................................................................................................................. A-1
Port Pinout Diagrams .......................................................................................................................... A-2
Ethernet Port Pinouts ................................................................................................................... A-2
Serial Port Pinouts ....................................................................................................................... A-2
Cable Wiring Diagrams ........................................................................................................................ A-2
Ethernet Cables........................................................................................................................... A-2
B.
Well Known Port Numbers ................................................................................................................ B-1
C.
SNMP Agents with MIB II & RS-232 Like Groups .............................................................................. C-1
D.
Switch MIB Groups ............................................................................................................................ D-1
E.
Compliance Note ............................................................................................................................... E-1
F.
Modbus/TCP Map .............................................................................................................................. F-1
1
1.
Introduction
Welcome to the Moxa NPort S8000, an advanced industrial serial device server integrated with a fully managed
redundant Ethernet switch, which enables easy network operation for your serial devices and connecting
Ethernet-enabled devices in industrial field applications.
There are four models in the NPort S8000 series:
•
NPort S8455I-MM-SC
Combination switch / device server with 4 RS-232/422/485 ports, 3 10/100M Ethernet ports, 2 100M
multi-mode fiber ports, SC connector, 15 KV ESD, 12–48 VDC, 0 to 60°C operating temperature
•
NPort S8455I-MM-SC-T
Combination switch / device server with 4 RS-232/422/485 ports, 3 10/100M Ethernet ports, 2 100M
multi-mode fiber ports, SC connector, 15 KV ESD, 12–48 VDC, -40 to 75°C operating temperature
•
NPort S8455I-SS-SC
Combination switch / device server with 4 RS-232/422/485 ports, 3 10/100M Ethernet ports, 2 100M
single-mode fiber ports, SC connector, 15 KV ESD, 12–48 VDC, 0 to 60°C operating temperature
•
NPort S8455I-SS-SC-T
Combination switch / device server with 4 RS-232/422/485 ports, 3 10/100M Ethernet ports, 2 100M
single-mode fiber ports, SC connector, 15 KV ESD, 12–48 VDC, -40 to 75°C operating temperature
•
NPort S8458-4S-SC-T
4 RS-232/422/485 ports, 4 10/100M Ethernet ports, 4 100M single-mode fiber ports with SC connector,
combo switch serial device server, 15 KV ESD, 12-48 VDC, -40 to 85°C operating temperature
The following topics are covered in this chapter:
 Overview
 Industrial Communications and Automation
 Industrial vs. Commercial
 Informative vs. Passive
 Package Checklist
 Product Features
 Product Specifications
 General Specifications
 Device Server Specifications
 Ethernet Switch Specifications
NPort S8000 Series
Introduction
Overview
The NPort S8458 is an industrial device server that integrates a managed Ethernet switch with a fully functional
serial device server. The NPort S8000 device servers are designed to make your industrial serial devices
instantly Internet-ready.
The NPort S8458 offers 4 fiber Ethernet ports, 4 Ethernet ports, and 4 RS-232/422/485 serial ports in a single
device. This not only saves cabinet space and reduces power consumption, but also saves money since you
don’t need to purchase separate switches and serial device servers.
The compact size of the NPort S8000 device servers makes them the ideal choice for connecting
RS-232/422/485 serial devices—such as PLCs, meters, and sensors—to an IP-based Ethernet LAN, making it
possible for your software to access serial devices anywhere over a LAN or the Internet.
The NPort S8000 is a fully equipped managed Ethernet Switch with a suite of useful maintenance and
monitoring functions, and is designed to provide smooth and reliable operation in harsh industrial
environments. It is ideal for keeping automation systems running continuously, sending status reports to help
prevent system damage and losses, and managing your industrial Ethernet networks and serial devices.
Industrial Communications and Automation
As the world’s networking and information technology becomes more complex, Ethernet has become the major
communications interface in many industrial communications and automation applications. In fact, a whole
new industry has sprung up to provide Ethernet products that comply with the requirements of demanding
industrial applications.
Industrial vs. Commercial
Users have found that when transplanting Ethernet from comfortable office environments to harsh and less
predictable industrial environments, commercial Ethernet equipment available in today’s market simply cannot
meet the high reliability requirements demanded by industrial applications. This means that more robust
networking equipment, commonly referred to as industrial Ethernet equipment, is required for these
applications.
Informative vs. Passive
Since industrial Ethernet devices are often located at the endpoints of a system, such devices cannot always
know what’s happening elsewhere on the network. This means that industrial Ethernet communication
equipment that connects these devices must provide system administrators with real-time alarm messages.
Package Checklist
The Moxa NPort S8000 Series products are shipped with the following items:
Standard Accessories
•
1 NPort S8000 serial device server
•
NPort Document & Software CD
•
NPort S8000 Series Quick Installation Guide
•
Product warranty statement
•
RJ45 to DB9 console port cable
Optional Accessories
•
Wall mounting kit
NOTE: Notify your sales representative if any of the above items is missing or damaged.
1-2
NPort S8000 Series
Introduction
Product Features
The NPort S8000 Series products enjoy the following features:
•
Make your serial devices Internet ready
•
Versatile socket operation modes, including TCP Server, TCP Client, and UDP
•
Easy-to-use Windows Utility for mass installation
•
Supports 10/100 Mbps Ethernet—auto detectable
•
Supports SNMP MIB-II for network management
•
Configuration auto-restore by LLDP (Link Layer Discovery Protocol)
•
Configurable serial data transmission priority
•
Multi-port managed Ethernet switch
•
Ethernet redundancy by Turbo Ring (recovery time < 20 ms), RSTP/STP (IEEE 802.1w/D)
•
QoS, IGMP snooping/GMRP, VLAN, LACP, SNMPv1/v2c/v3, RMON supported
•
4 serial ports device server, support RS-232/422/RS-485
•
2K VDC isolation protection for serial port (NPort S8455 series only)
•
Surge protection for serial/power/Ethernet
•
Adjustable pull high/low resistor and Terminators for the RS-485 port (NPort S8455 series only)
•
2- or 4-wire RS-485 with patented ADDC™ (Automatic Data Direction Control)
•
Built-in 15 KV ESD protection for all serial signals
Product Specifications
General Specifications
Port Summary
Serial Ports: 4 RS-232/422/485 ports
Ethernet Switch Ports:
NPort S8455: 3 RJ45 copper ports and 2 single/multi-mode fiber ports
NPort S8458: 4 RJ45 copper ports and 4 single-mode fiber ports
Console Ports: 1 (8-pin RJ45 connector)
Physical Characteristics
Housing: Metal
Weight: 995 g
Dimensions:
NPort S8455: 73.1 x 134 x 105 mm (2.88 x 5.27 x 4.13 in)
NPort S8458: 93 × 144 × 125 mm (3.66 × 5.64 × 4.92 in)
Environmental Limits
Operating Temperature:
Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models:
NPort S8455-T: -40 to 75° C (-40 to 167° F)
NPort S8458-T: -40 to 85° C (-40 to 185° F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity: 5 to 95% (non-condensing)
1-3
NPort S8000 Series
Introduction
ATTENTION
•
This equipment is intended to be used in Restrict Access Location, like computer room. The access can only
be gained by SERVICE PERSONS or by USERS who have been instructed about the metal chassis of the
equipment is so hot that service persons have to pay special attention or take special protection before
touching it. Further, the access is through the use of key or security identity system. Only authorized by
well trained professional person can access the restrict access location.
•
External metal parts are hot!! Before touching it, special attention or protection is necessary.
•
CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According
to the Instructions.
Power Requirements
Input Voltage: 12 to 48 VDC
Power Consumption:
NPort S8455: 935 mA @ 12 V, 470 mA @ 24 V
NPort S8458: 940 mA @ 12 V, 470 mA @ 24 V
Standards and Certifications
Safety: UL 508, UL 60950-1, EN 60950-1
EMC: CE, FCC
EMI: EN 55022 Class A, FCC Part 15 Subpart B Class A
EMS:
EN 55024,
IEC 61000-4-2 (ESD) Level 4,
IEC 61000-4-4 (EFT) Level 4,
IEC 61000-4-5 (Surge)
Level 1 for serial ports,
Level 2 for LAN ports,
Level 3 for power lines
Warranty
Warranty Period: 5 years
Details: See www.moxa.com/warranty
Device Server Specifications
Serial Interface
Number of Ports: 4
Serial Standards: RS-232/422/485
Connector: DB9 male
Serial Line Protection:
• 15 KV ESD protection for all signals
• 2 KV isolation protection (NPort S8455 series only)
RS-485 Data Direction Control: ADDC® (automatic data direction control)
Pull High/Low Resistor for RS-485: 1 KΩ, 150 KΩ (NPort S8455 series only)
Terminator for RS-485: 55 Ω, 120 Ω (NPort S8455 series only)
Console Port: Dedicated RS-232 console port (8-pin RJ45)
Serial Communication Parameters
Data Bits: 5, 6, 7, 8
Stop Bits: 1, 1.5, 2
Parity: None, Even, Odd, Space, Mark
Flow Control: RTS/CTS and XON/XOFF
Baudrate: 50 bps to 921.6 Kbps
Serial Signals
RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
1-4
NPort S8000 Series
Introduction
RS-422: Tx+, Tx-, Rx+, Rx-, GND
RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w: Data+, Data-, GND
Software
Configuration Options: Web Console, Telnet Console, Serial Console, Windows Search Utility
Windows Real COM Drivers: Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7 x86/x64,
Embedded CE 5.0/6.0, XP Embedded
Fixed TTY Drivers: SCO Unix, SCO OpenServer, UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6,
Solaris 10, FreeBSD, AIX 5.x
Linux Real TTY Drivers: Linux kernel 2.4.x, 2.6.x
Operation Modes: Real COM, TCP Server, TCP Client, UDP, RFC2217
Management: SNMP MIB-II
IP Routing: Static, RIP-I, RIP-II
Reliability
Alert Tools: Built-in buzzer and RTC (real-time clock)
Automatic Reboot Trigger: Built-in WDT (watchdog timer)
MTBF (mean time between failures): 200,951 hrs
Ethernet Switch Specifications
Ethernet Interface
Standards:
IEEE 802.3 for 10BaseT
IEEE 802.3u for 100BaseT(X) and 100Base FX
IEEE 802.3x for Flow Control
IEEE 802.1D for Spanning Tree Protocol
IEEE 802.1w for Rapid STP
IEEE 802.1Q for VLAN Tagging
IEEE 802.1p for Class of Service
IEEE 802.1x for Authentication
IEEE 802.3ad for Port Trunk with LACP
Network Protocols: ICMP, IP, TCP, UDP, ARP, Telnet, DNS, HTTP, SMTP, SNTP, IGMPv1/v2 device, GVRP,
SNMPv1/v2c/v3, DHCP Server/Client, DHCP Option 82, BootP, TFTP, SNTP, SMTP, RARP, GMRP, LACP, RMON
MIB: MIB-II, Ethernet-Like MIB, P-BRIDGE MIB, Q-BRIDGE MIB, Bridge MIB, RSTP MIB, RMON MIB Group 1,
2, 3, 9
Flow Control: IEEE 802.3x flow control, back pressure flow control interface
Optical Fiber Interface
Distance:
• Multi-mode: 0 to 4 km, 1310 nm (62.5/125 μm, 500 MHz*km)
• Single-mode: 0 to 40 km, 1310 nm (9/125 μm, 3.5 PS/(nm*km))
Min. TX Output:
• Multi-mode: -20 dBm
• Single-mode: - 5 dBm
Max. TX Output:
• Multi-mode: -14 dBm
• Single-mode: 0 dBm
Sensitivity:
• Multi-mode: -34 to -30 dBm
• Single-mode: -36 to -32 dBm
1-5
NPort S8000 Series
Introduction
ATTENTION
LED or LASER components in compliance with IEC 60825-1 (2001):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT.
Switch Properties
Priority Queues: 4
Max. Number of Available VLANs: 64
VLAN ID Range: VID 1 to 4094
IGMP Groups: 256
Switch Interface
RJ45 Ports: 10/100BaseT(X) auto negotiation speed, F/H duplex mode, and auto MDI/MDI-X connection
DIP Switches: Turbo Ring, Master, Coupler, Reserve
Alarm Contact: 2 relay outputs with current carrying capacity of 1A @ 24 VDC
1-6
2
2.
Getting Started
This chapter includes information about installing NPort S8000 series device servers. Note that the manual
uses the NPort S8455 series as example to illustrate the functionality of NPort S8000 series in chapter 2, 3, 4,
5 and 6.
The following topics are covered in this chapter:
 Panel Layout
 Dimensions
 NPort S8455 series
 NPort S8458 series
 Connecting the Hardware
 Wiring Requirements
 Connecting the Power
 Connecting to the Network
 Connecting to a Serial Device
 LED Indicators
 Adjustable Pull High/low Resistors and Terminators for the RS-485 Port (NPort S8455 series only)
 Wiring the Relay Contact
 Wiring the Digital Inputs
NPort S8000 Series
Getting Started
Panel Layout
Reset Button
PWR1, DI1 and DI2
Serial Console
4 DIP switches for
PWR1, RELAY 1
Turbo Ring settings
and RELAY 2
LED Indicators
Fiber Port
Serial port (DB9
l )
Ethernet port (RJ45)
NPort S8455 series
2-2
NPort S8000 Series
Getting Started
Dimensions
NPort S8455 series
2-3
NPort S8000 Series
Getting Started
NPort S8458 series
Connecting the Hardware
This section describes how to connect the NPort S8000 to serial devices for initial testing purposes. We cover
Wiring Requirements, Connecting the Power, Grounding the NPort S8000, Connecting to the
Network, Connecting to a Serial Device, and LED Indicators.
2-4
NPort S8000 Series
Getting Started
Wiring Requirements
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or wiring your NPort S8000.
Wiring Caution!
Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes
dictating the maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could overheat, causing serious damage to your
equipment.
Temperature Caution!
Please take care when handling the NPort S8000. When plugged in, the NPort S8000’s internal components
generate heat, and consequently the casing may feel hot to the touch.
You should heed the following:
•
Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must
cross, make sure the wires are perpendicular at the intersection point.
NOTE: Do not run signal or communication wiring and power wiring in the same wire conduit. To avoid
interference, wires with different signal characteristics should be routed separately.
•
You can use the type of signal transmitted through a wire to determine which wires should be kept separate.
The rule of thumb is that wiring that shares similar electrical characteristics can be bundled together.
•
Keep input wiring and output wiring separate.
•
Where necessary, it is strongly advised that you label wiring to all devices in the system.
Connecting the Power
Connect the 12-48 VDC power line with the NPort S8000’s terminal block. If the power is properly supplied, the
“Ready” LED will show a solid red color until the system is ready, at which time the “Ready” LED will change to
a green color.
Take the following steps to wire the redundant power inputs:
1. Insert the negative/positive DC wires into the V-/V+ terminals.
2. To keep the DC wires from pulling loose, use a small flat-blade screwdriver to tighten the wire-clamp
screws on the front of the terminal block connector.
3. Insert the plastic terminal block connector prongs into the terminal block receptor, which is located on the
EDS’s top panel.
2-5
NPort S8000 Series
Getting Started
Connecting to the Network
Connect one end of the Ethernet cable to the NPort S8000’s 10/100M Ethernet port and the other end of the
cable to the Ethernet network. If the cable is properly connected, the NPort S8000 will indicate a valid
connection to the Ethernet in the following ways:
•
The Ethernet LED maintains a solid green color when connected to a 100 Mbps Ethernet network.
•
The Ethernet LED will flash when Ethernet packets are being transmitted or received.
Connecting to a Serial Device
Connect the serial data cable between the NPort S8000 and the serial device.
LED Indicators
The LED indicators of NPort S8000 series are described in the following table.
Type
Color
Meaning
PWR 1
Green
Power 1 input
PWR 2
Green
Power 2 input
LINK (FX)
Green
FX port 100 Mbps is active
Blinking
Data is being transmitted/received at 100 Mbps
LINK
Green
100 Mbps Ethernet connection
Blinking
10 Mbps Ethernet connection
Master
Green
When the NPort is the Master of this Turbo Ring
Yellow
When the NPort is the Ring Master of this Turbo Ring and the Turbo
Ring is broken
Coupler
Green
When the NPort enables the coupling function to form a backup path
Serial Port TX
Green
The serial port is transmitting data.
Serial Port RX
Yellow
The serial port is receiving data.
Ready
Red
Steady On: Power is on and NPort is booting up.
Blinking: Indicates an LAN IP conflict, or DHCP or BOOTP server did
not respond properly.
Green
Steady On: Power is on and NPort is functioning normally.
Blinking: The device server has been located by Administrator’s
Location function.
Off
Power is off, or power error condition exists.
Adjustable Pull High/low Resistors and Terminators for the
RS-485 Port (NPort S8455 series only)
In some critical environments, you may need to add termination resistors to prevent the reflection of serial
signals. When using termination resistors, it is important to set the pull high/low resistors correctly so that the
electrical signal is not corrupted. Since there is no resistor value that works for every environment, DIP
switches are used to set the pull high/low resistor values for each RS-485 port.
To set the pull high/low resistors to 150 KΩ, make sure both of the assigned DIP switches are in the OFF
position. This is the default setting.
To set the pull high/low resistors to 1 KΩ, make sure both of the assigned DIP switches are in the ON
position.
2-6
NPort S8000 Series
Getting Started
SW
Default
1
2
3
4
3&4
Pull High
Pull Low
Terminator
Terminator
Terminator
ON
1 KΩ
1 KΩ
120 Ω
100 Ω
55 Ω
OFF
150 KΩ
150 KΩ
–
–
–
ATTENTION
Do not set the resistors to 1 KΩ. When using RS-232. Doing so will degrade the RS-232 signals and reduce the
effective communication distance.
Wiring the Relay Contact
The NPort 8455I-MM-SChas two sets of relay output—relay 1 and relay 2. Each relay contact consists of two
contacts of the terminal block on the NPort 8455I-MM-SC’s top panel. Refer to the next section for detailed
instructions on how to connect the wires to the terminal block connector, and how to attach the terminal block
connector to the terminal block receptor. The meaning of the two contacts used to connect the relay contacts
is illustrated below.
The fault circuit will open if
1. A relay warning event is triggered,
OR
2. The EDS-505A/508A is the Master of this Turbo Ring, and the
Turbo Ring is broken,
OR
3. Start-up failure.
If none of these three conditions is met, the fault circuit will remain
closed.
Wiring the Digital Inputs
The NPort 8455I-MM-SC unit has two sets of digital inputs, DI 1 and DI 2. Each DI consists of two contacts of
the 6-pin terminal block connector on the NPort 8455I-MM-SC’s top panel. The remaining contacts are used for
the NPort 8455I-MM-SC’s two DC inputs. Top and front views of one of the terminal block connectors are shown
below.
2-7
NPort S8000 Series
Getting Started
Take the following steps to wire the digital inputs:
1. Insert the negative (ground)/positive DI wires into the ┴/I1
terminals.
2. To keep the DI wires from pulling loose, use a small flat-blade
screwdriver to tighten the wire-clamp screws on the front of the
terminal block connector.
3. Insert the plastic terminal block connector prongs into the
terminal block receptor, which is located on the NPort
8455I-MM-SC’s top panel.
2-8
3
3.
Initial IP Address Configuration
When setting up the NPort S8000 for the first time, the first thing you should do is configure its IP address. This
chapter introduces the different methods that can be used. The following topics are covered in this chapter:
 Static and Dynamic IP Addresses
 Factory Default IP Address
 Configuration Options
 Web Console
 ARP
 Telnet Console
 Serial Console
NPort S8000 Series
Initial IP Address Configuration
Static and Dynamic IP Addresses
Determine whether your NPort S8000 needs to use a static IP or dynamic IP address (either DHCP or BOOTP
application).
•
If your NPort S8000 is used in a static IP environment, you will assign a specific IP address using one
of the tools described in this chapter.
•
If your NPort S8000 is used in a dynamic IP environment, the IP address will be assigned
automatically from over the network. In this case, set the IP configuration mode to DHCP, BOOTP.
ATTENTION
Consult your network administrator on how to reserve a fixed IP address for your NPort S8000 in the MAC-IP
mapping table when using a DHCP server or BOOTP server. For most applications, you should assign a fixed IP
address to your NPort S8000.
Factory Default IP Address
The NPort S8000 is configured with the following default private IP address:
192.168.127.254
Note that IP addresses that begin with “192.168” are referred to as private IP addresses. Devices configured
with a private IP address are not directly accessible from a public network. For example, you would not be able
to ping a device with a private IP address from an outside Internet connection. If your application requires
sending data over a public network, such as the Internet, your NPort S8000 will need a valid public IP address,
which can be leased from a local ISP.
Configuration Options
Web Console
You may configure your NPort S8000 using a standard web browser. Please refer to chapter 5 and chapter 6,
for details on how to access and use the NPort S8000 web console.
ARP
You may use the ARP (Address Resolution Protocol) command to set up an IP address for your NPort S8000.
The ARP command tells your computer to associate the NPort S8000’s MAC address with an IP address.
Afterwards, use Telnet to access the NPort S8000 and its IP address will be reconfigured.
ATTENTION
In order to use the ARP setup method, both your computer and the NPort S8000 must be connected to the
same LAN. Alternatively, you may use a cross-over Ethernet cable to connect the NPort S8000 directly to your
computer’s Ethernet card. Before executing the ARP command, your NPort S8000 must be configured with the
factory default IP address (192.168.127.254) and your computer and the NPort S8000 must be on the same
subnet.
To use ARP to configure the IP address, complete the following:
1. Obtain a valid IP address for your NPort S8000 from your network administrator.
2. Obtain your NPort S8000’s MAC address from the label on the bottom panel.
3-2
NPort S8000 Series
Initial IP Address Configuration
3. Execute the arp -s command from your computer’s MS-DOS prompt as follows:
arp -s <IP address> <MAC address>
For example,
C:\> arp -s 192.168.200.100 00-90-E8-04-00-11
4. Next, execute a special Telnet command by entering the following exactly:
telnet 192.168.200.100 6000
When you enter this command, a Connect failed message will appear, as shown below.
5. After the NPort S8000 reboots, its IP address will assigned to the new address and you can reconnect using
Telnet to verify that the update was successful.
Telnet Console
Depending on how your computer and network are configured, you may find it convenient to use network
access to set up your NPort S8000’s IP address. This can be done using Telnet.
1. From the Windows desktop, select Start  Run, and type the following in the Run window:
Telnet 192.168.127.254
If your IP address is different from the default setting, use your IP address instead. Click OK.
3-3
NPort S8000 Series
Initial IP Address Configuration
2. The console terminal type selection is displayed as shown. Enter 1 for ansi/vt100 and press ENTER to
continue.
3. Enter the console password if you are prompted to do so, and press ENTER.
4. Press B or use the arrow keys to select Basic, and then press ENTER.
3-4
NPort S8000 Series
Initial IP Address Configuration
5. Press N or use the arrow keys to select Network, and then press ENTER.
6. Use the arrow keys to move the cursor to IP address. Use the DELETE, BACKSPACE, or SPACE keys to
erase the current IP address, and then type in the new IP address and press ENTER. Note that if you are
using a dynamic IP configuration (BOOTP, SHCP, etc.), you will need to go to the Auto IP configuration
field and press ENTER to select the appropriate configuration.
7. Press ESC twice to return to previous page. Select Activate and Press “Y” to confirm the modification.
3-5
NPort S8000 Series
Initial IP Address Configuration
8. Press ESC to return to previous page.
Serial Console
The NPort S8000 supports configuration through the serial console, which is the same as the Telnet console but
accessed through the RS-232 console port rather than through the network. Once you have entered the serial
console, the configuration options and instructions are the same as if you were using the Telnet console.
The following instructions and screenshots show how to enter the serial console using PComm Terminal
Emulator, which is available free of charge as part of the PComm Lite suite. You may use a different terminal
emulator utility, although your actual screens and procedures may vary slightly from the following instructions.
1. Use a serial cable to connect the NPort S8000’s serial console port to your computer’s male RS-232 serial
port.
ATTENTION
The NPort S8000 has a dedicated serial console port.
2. From the Windows desktop select Start  All Programs  PComm Lite  Terminal Emulator.
3. The PComm Terminal Emulator window should appear. From the Port Manager menu, select Open, or
simply click the Open icon as shown below:
3-6
NPort S8000 Series
Initial IP Address Configuration
4. The Property window opens automatically. Select the Communication Parameter tab, then select the
appropriate COM port for the connection (COM1 in this example). Configure the parameters for 19200, 8,
N, 1 (19200 for Baud Rate, 8 for Data Bits, None for Parity, and 1 for Stop Bits).
5. From the Property window’s Terminal page, select ANSI or VT100 for Terminal Type and click OK.
The NPort S8000 will then automatically switch from data mode to console mode.
6. After you enter the password, or if password protection was not enabled, you will be prompted to select the
terminal mode. Press 1 for ansi/vt100 and then press ENTER.
3-7
NPort S8000 Series
Initial IP Address Configuration
7. The main menu should come up. Once you are in the console, you may configure the IP address through the
Network menu item, just as with the Telnet console. Please refer to steps 4 to 8 in the Telnet Console
section to complete the initial IP configuration.
3-8
4
4.
Choosing the Serial Operation Mode
In this chapter, we describe the various serial operation modes of the NPort S8000. The options include an
operation mode that uses a driver installed on the host computer, and operation modes that rely on TCP/IP
socket programming concepts. After choosing the proper operation mode in this chapter, refer to Chapter 5 for
detailed configuration parameter definitions.
The following topics are covered in this chapter:
 Overview
 Real COM Mode
 RFC2217 Mode
 TCP Server Mode
 TCP Client Mode
 UDP Mode
 Disabled Mode
NPort S8000 Series
Choosing the Serial Operation Mode
Overview
The device server function of the NPort S8000 enables network operation of traditional RS-232/422/485
devices, in which a device server is a tiny computer equipped with a CPU, real-time OS, and TCP/IP protocols
that can bi-directionally translate data between the serial and Ethernet formats. Your computer can access,
manage, and configure remote facilities and equipment over the Internet from anywhere in the world.
Traditional SCADA and data collection systems rely on serial ports (RS-232/422/485) to collect data from
various kinds of instruments. Since the NPort S8000 networks instruments equipped with an RS-232/422/485
communication port, your SCADA and data collection system will be able to access all instruments connected
to a standard TCP/IP network, regardless of whether the devices are used locally or at a remote site.
The NPort S8000 is an external IP-based network device that allows you to expand the number of serial ports
for a host computer on demand. As long as your host computer supports the TCP/IP protocol, you won’t be
limited by the host computer’s bus limitation (such as ISA or PCI), or lack of drivers for various operating
systems.
In addition to providing socket access, the NPort also comes with a Real COM/TTY driver that transmits all serial
signals intact. This means that your existing COM/TTY-based software can be preserved, without needing to
invest in additional software.
Three different Socket Modes are available: TCP Server, TCP Client, and UDP Server/Client. The main
difference between the TCP and UDP protocols is that TCP guarantees delivery of data by requiring the recipient
to send an acknowledgement to the sender. UDP does not require this type of verification, making it possible
to offer speedier delivery. UDP also allows multicasting of data to groups of IP addresses.
Real COM Mode
The NPort S8000 comes equipped with COM drivers that
work with Windows 9x/NT/2000/XP/2003/Vista/2008 (all
x86/x64) systems, and also TTY drivers for Linux and Unix
systems. The driver establishes a transparent connection
between host and serial device by mapping the IP port of
the NPort’s serial port to a local COM/TTY port on the host
computer. This operation mode also supports up to 8
simultaneous connections, so that multiple hosts can
collect data from the same serial device at the same time.
The important point is that Real COM Mode allows users to continue using RS-232/422/485 serial
communications software that was written for pure serial communications applications. The driver intercepts
data sent to the host’s COM port, packs it into a TCP/IP packet, and then redirects it through the host’s Ethernet
card. At the other end of the connection, the NPort accepts the Ethernet frame, unpacks the TCP/IP packet, and
then transparently sends it to the appropriate serial device attached to one of the NPort’s serial ports.
ATTENTION
Real COM Mode allows several hosts to have access control over the same NPort. The driver that comes with
your NPort controls host access to attached serial devices by checking the host’s IP address.
Modify the Accessible IP Setting table when the legal IP address is required in your application
4-2
NPort S8000 Series
Choosing the Serial Operation Mode
RFC2217 Mode
RFC-2217 mode is similar to Real COM mode. That is, a driver is used to establish a transparent connection
between a host computer and a serial device by mapping the serial port on the NPort S8000 to a local COM port
on the host computer. RFC2217 defines general COM port control options based on the Telnet protocol. Third
party drivers supporting RFC-2217 are widely available on the Internet and can be used to implement Virtual
COM mapping to your NPort S8000 serial port(s).
TCP Server Mode
In TCP Server mode, the NPort S8000 provides a unique IP port
address on a TCP/IP network. The NPort S8000 waits passively to be
contacted by the host computer, allowing the host computer to
establish a connection with and get data from the serial device. This
operation mode also supports up to 8 simultaneous connections, so
that multiple hosts can collect data from the same serial device—at
the same time.
As illustrated in the figure, data transmission proceeds as follows:
1. The host requests a connection from the NPort configured for
TCP Server Mode.
Once the connection is established, data can be transmitted in both
directions—from the host to the NPort, and from the NPort to the
host.
TCP Client Mode
In TCP Client mode, the NPort S8000 can actively establish
a TCP connection to a pre-defined host computer when
serial data arrives.
After the data has been transferred, the NPort S8000 can
automatically disconnect from the host computer by using
the TCP alive check time or Inactivity time settings.
Refer to chapter 5 for more details.
As illustrated in the figure, data transmission proceeds as
follows:
1. The NPort configured for TCP Client Mode requests a
connection from the host.
2. Once the connection is established, data can be
transmitted in both directions—from the host to the
NPort, and from the NPort to the host.
4-3
NPort S8000 Series
Choosing the Serial Operation Mode
UDP Mode
Compared to TCP communication, UDP is faster and
more efficient. In UDP mode, you can multicast data
from the serial device to multiple host computers,
and the serial device can also receive data from
multiple host computers, making this mode ideal for
message display applications.
Disabled Mode
When the Operation Mode for a particular port is set to Disabled, that port will be disabled.
4-4
5
5.
Basic Settings and Device Server
Configuration
The Web Console is the most user-friendly way to configure the NPort S8000.
This chapter covers the following topics:
 Opening Your Browser
 Basic Settings
 General Settings
 Time Settings
 Network Settings
 Serial Settings
 Operation Modes
 Serial Parameters
 Serial ToS Settings
NPort S8000 Series
Basic Settings and Device Server Configuration
Opening Your Browser
1. Open your browser with the cookie function enabled. (To enable your browser for cookies, right click on
your desktop Internet Explorer icon, select Properties, click on the Security tab, and then select the three
Enable options as shown in the figure below.)
2. Type 192.168.127.254 in the Address input box (use the correct IP address if different from the default),
and then press Enter.
3. Input the password if prompted. The password will be transmitted with MD5 encryption over the Ethernet.
Note that you will not be prompted to enter the password if the NPort is not currently password protected.
ATTENTION
If you use other web browsers, remember to Enable the functions to “allow cookies that are stored on your
computer” or “allow per-session cookies.” Device servers use cookies only for “password” transmission.
ATTENTION
Refer to Chapter 3, “Initial IP Address Configuration,” to see how to configure the IP address. Examples shown
in this chapter use the Factory Default IP address (192.168.127.254).
5-2
NPort S8000 Series
Basic Settings and Device Server Configuration
The NPort S8000 homepage will open. On this page, you can see a brief description of the Web Console.
ATTENTION
If you forgot the password, the ONLY way to start configuring the NPort is to load factory defaults by using the
Reset button.
ATTENTION
Remember to export the configuration file when you have finished the configuration. After using the Reset
button to load factory defaults, your configuration can be easily reloaded into the NPort by using the Import
function. Refer to Chapter 6, Maintenance / Update System Files for more details about using the Export and
Import functions.
ATTENTION
If your NPort application requires using password protection, you must enable the cookie function in your
browser. If the cookie function is disabled, you will not be allowed to enter the Web Console Screen.
5-3
NPort S8000 Series
Basic Settings and Device Server Configuration
Basic Settings
General Settings
Server name
Setting
Factory Default
Necessity
1 to 40 characters
[model name]_[Serial No.]
Optional
This column is useful for specifying the application of this NPort device server.
Server Location
Setting
Factory Default
Necessity
1 to 80 characters
Empty
Optional
This column is useful for specifying the location of this NPort device server.
Server Description
Setting
Factory Default
Necessity
1 to 40 characters
Empty
Optional
This column is useful for specifying more detailed description of this NPort S8000, such as the serial devices
connected to the NPort S8000.
Maintainer contact info
Setting
Factory Default
Necessity
1 to 40 characters
Empty
Optional
This column is useful for specifying the contact information of the administrator responsible for maintaining this
NPort S8000.
5-4
NPort S8000 Series
Basic Settings and Device Server Configuration
Time Settings
Time
The NPort S8000 has a time calibration function based on information from an NTP server or user specified
Time and Date information. Functions such as Auto warning “Email” can add real-time information to the
message.
ATTENTION
There is a risk of explosion if the real-time clock battery is replaced with the wrong type!
The NPort S8000’s real time clock is powered by a rechargeable battery. We strongly recommend that you do
not attempt replacement of the rechargeable battery without help from a qualified Moxa support engineer. If
you need to change the battery, please contact the Moxa RMA service team.
Current Time
Setting
Description
Factory Default
User adjustable time.
The time parameter allows configuration of the local time in
None (hh:mm:ss)
local 24-hour format.
Current Date
Setting
Description
Factory Default
User adjustable date.
The date parameter allows configuration of the local date in
None
yyyy/mm/dd format.
(yyyy/mm/dd)
Daylight Saving Time
Daylight saving time (also know as DST or summer time) involves advancing clocks (usually 1 hour) during
the summer time to provide an extra hour of daylight in the afternoon.
Start Date
Setting
Description
Factory Default
User adjustable date.
The Start Date parameter allows users to enter the date that
None
daylight saving time begins.
End Date
Setting
Description
Factory Default
5-5
NPort S8000 Series
User adjustable date.
Basic Settings and Device Server Configuration
The End Date parameter allows users to enter the date that
None
daylight saving time ends.
Offset
Setting
Description
Factory Default
User adjustable hour.
The offset parameter indicates how many hours forward the
None
clock should be advanced.
Time Settings
Time Zone
NOTE
Setting
Description
User selectable time
The time zone setting allows conversion from GMT (Greenwich GMT (Greenwich
Factory Default
zone.
Mean Time) to local time.
Mean Time)
Changing the time zone will automatically correct the current time. You should configure the time zone before
setting the time.
Time Server IP/Name
Setting
Description
Factory Default
1st Time Server
IP or Domain address (e.g., 192.168.1.1 or
None
IP/Name
time.stdtime.gov.tw or time.nist.gov).
2nd Time Server
The NPort S8450I-MM-SC will try to locate the 2nd NTP Server
IP/Name
if the 1st NTP Server fails to connect.
Time Server Query Period
Setting
Description
Query Period
This parameter determines how frequently the time is updated 600 seconds
Factory Default
from the NTP server.
Network Settings
You must assign a valid IP address to the NPort S8000/5450 before it will work in your network environment.
Your network system administrator should provide you with an IP address and related settings for your network.
5-6
NPort S8000 Series
Basic Settings and Device Server Configuration
The IP address must be unique within the network (otherwise, the NPort S8000 will not have a valid connection
to the network). First time users can refer to Chapter 3, Initial IP Address Configuration, for more information.
You can choose from four possible IP Configuration modes—Disable (Static) , DHCP, and BOOTP—located
under the web console screen’s IP configuration drop-down box.
Auto IP Configuration
Setting
Description
Factory Default
Disable
Set up the NPort S8450I-MM-SC’s IP address manually.
Disable
By DHCP
The NPort S8450I-MM-SC’s IP address will be assigned
automatically by the network’s DHCP server.
By BOOTP
The NPort S8450I-MM-SC’s IP address will be assigned
automatically by the network’s BOOTP server.
ATTENTION
In Dynamic IP environments, the firmware will retry 3 times every 30 seconds until network settings are
assigned by the DHCP or BOOTP server. The Timeout for each try increases from 1 second, to 3 seconds, to 5
seconds.
If the DHCP/BOOTP Server is unavailable, the firmware will use the default IP address (192.168.127.254),
Netmask, and Gateway for IP settings.
IP Address
Setting
Description
Factory Default
IP Address of the NPort Identifies the NPort S8450I-MM-SC on a TCP/IP network.
192.168.127.254
S8450I-MM-SC
An IP address is a number assigned to a network device (such as a computer) as a permanent address on the
network. Computers use the IP addresses to identify and talk to each other over the network. Choose a proper
IP address which is unique and valid in your network environment.
Subnet Mask
Setting
Description
Factory Default
Subnet mask of the
Identifies the type of network to which the NPort
255.255.255.0
NPort S8450I-MM-SC
S8450I-MM-SC is connected (e.g., 255.255.0.0 for a Class B
network, or 255.255.255.0 for a Class C network).
A subnet mask represents all the network hosts at one geographic location, in one building, or on the same
local area network. When a packet is sent out over the network, the NPort will use the subnet mask to check
whether the desired TCP/IP host specified in the packet is on the local network segment. If the address is on the
same network segment as the NPort, a connection established directly from the NPort. Otherwise, the
connection is established through the given default gateway.
Default Gateway
Setting
Description
Factory Default
Default Gateway of the The IP address of the router that connects the LAN to an
NPort S8450I-MM-SC
None
outside network.
A gateway is a network gateway that acts as an entrance to another network. Usually, the computers that
control traffic within the network or at the local Internet service provider are gateway nodes. The NPort needs
to know the IP address of the default gateway computer in order to communicate with the hosts outside the
local network environment. For correct gateway IP address information, consult the network administrator.
5-7
NPort S8000 Series
Basic Settings and Device Server Configuration
DNS IP Address
Setting
Description
1st DNS Server’s
The IP address of the DNS Server used by your network. After None
Factory Default
IP Address
entering the DNS Server’s IP address, you can input the NPort
S8450I-MM-SC’s URL (e.g., www.NPort
S8450I-MM-SC.company.com) in your browser’s address field,
instead of entering the IP address.
2nd DNS Server’s
The IP address of the DNS Server used by your network. The
IP Address
NPort S8450I-MM-SC will try to locate the 2nd DNS Server if
None
the 1st DNS Server fails to connect.
When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for
the website’s correct IP address, and the computer user the response to connect to the web server. DNS is the
way Internet domain names are identified and translated into IP addresses. A domain name is an alphanumeric
name, such as moxa.com, that is usually easier to remember. A DNS server is a host that translates this kind
of text-based domain name into the numeric IP address used to establish a TCP/IP connection.
In order to use the NPort’s DNS feature, you need to set the IP address of the DNS server to be able to access
the host with the domain name. The NPort provides DNS server 1 and DNS server 2 configuration items to
configure the IP address of the DNS server. DNS Server 2 is included for use when DNS sever 1 is unavailable.
The NPort plays the role of DNS client. Functions that support domain name in the NPort are Time Sever IP
Address, TCP Client-Destination IP Address, Mail Server, SNMP Trap IP Address, and IP Location
Server.
TCP alive check time
Setting
Description
Factory Default
0 to 99 min
This field specifies how long the NPort S8000 will wait for a
7 min
response to “keep alive” packets before closing the TCP
connection. The NPort S8000 checks connection status by
sending periodic “keep alive” packets. If the remote host does
not respond to the packet within the time specified in this field,
the NPort S8000 will force the existing TCP connection to close.
For socket and Real COM Mode, the NPort S8000 will listen for
another TCP connection from another host after closing the
connection. If the TCP alive check time is set to 0, the TCP
connection will remain open and will not send any “keep alive”
packets.
All serial ports use the same TCP live check time in NPort S8000.
Serial Settings
Operation Modes
Click on Operation Modes, located under Serial Settings, to display serial port settings for 4 serial ports. To
modify serial operation mode settings for a particular port, click on Operation Modes of the serial port in the
window of right hand site.
5-8
NPort S8000 Series
Basic Settings and Device Server Configuration
Real COM Mode
Port Settings
Max connection
Setting
Factory Default
Necessity
1, 2, 3, 4, 5, 6, 7, 8
1
Required
This field is used if you need to receive data from different hosts simultaneously. When set to 1, only one
specific host can access this port on the NPort S8000, and the Real COM driver on that host will have full control
over the port. When set to 2 or greater, the Real COM drivers for up to the specified number of hosts may open
this port at the same time. When multiple hosts’ Real COM drivers open the port at the same time, the COM
driver only provides a pure data tunnel—no control capability provided. The serial port parameters will use
firmware settings instead of your application program (AP) settings.
Application software that is based on the COM driver will receive a driver response of “success” when the
software uses any of the Win32 API functions. The firmware will only send data back to the driver on the host.
5-9
NPort S8000 Series
Basic Settings and Device Server Configuration
Data will be sent first-in-first-out when data enters the NPort S8000 from the Ethernet interface.
ATTENTION
When Max connection is set to 2 to 8, this means that the NPort use a “multi connection application” (i.e., 2 to
8 hosts are allowed access to the port at the same time). When using a multi connection application, the NPort
will use the serial communication parameters set in the console. All of the hosts connected to that port must
use the same serial settings. If one of the hosts opens the COM port with parameters that are different from the
NPort’s console setting, data communication may not work properly.
Ignore jammed IP
Setting
Factory Default
Necessity
Enable or Disable
Disable
Optional
Previously, if “max connection” was greater than 1, the serial device was transmitting data, and a connected
host was not responding, the NPort would wait until the data was transmitted successfully before transmitting
the second group of data to all hosts. Currently, if you select Enable for “Ignore jammed IP,” the host that is not
responding will be ignored, but the data will still be transmitted to the other hosts.
Allow driver control
Setting
Factory Default
Necessity
Enable or Disable
Disable
Optional
If “max connection” is greater than 1, the NPort will ignore driver control commands from all connected hosts.
However, if you set “Allow driver control” to YES, control commands will be accepted. Note that since the NPort
S8000 may get configuration changes from multiple hosts, the most recent command received will take
precedence.
Connection goes down
Setting
Factory Default
Necessity
Always High or Always
Always High
Optional
Low
You can configure what happens to the RTS and DTR signals when the Ethernet connection goes down. For
some applications, serial devices need to know the Ethernet link status through RTS or DTR signals sent
through the serial port. Use always low if you want the RTS and DTR signal to change their state to low when
the Ethernet connection goes down. Use always high if you do not want the Ethernet connection status to
affect the RTS or DTR signals.
Data Packing
Packet length
Setting
Factory Default
Necessity
0 to 1024
0
Optional
Default = 0, The Delimiter Process will be followed, regardless of the length of the data packet. If the data
length (in bytes) matches the configured value, the data will be forced out. The data length can be configured
for 0 to 1024 bytes. Set to 0 if you do not need to limit the length.
Delimiter 1
Setting
Factory Default
Necessity
00 to FF
None
Optional
Setting
Factory Default
Necessity
00 to FF
None
Optional
Delimiter 2
When Delimiter 1 is enabled, the serial port will clear the buffer and send the data to the Ethernet port when
a specific character, entered in hex format, is received. A second delimiter character may be enabled and
5-10
NPort S8000 Series
Basic Settings and Device Server Configuration
specified in the Delimiter 2 field, so that both characters act as the delimiter to indicate when data should be
sent.
ATTENTION
Delimiter 2 is optional. If left blank, then Delimiter 1 alone trips clearing of the buffer. If the size of the serial
data received is greater than 1 KB, the NPort will automatically pack the data and send it to the Ethernet.
However, to use the delimiter function, you must at least enable Delimiter 1. If Delimiter 1 is left blank and
Delimiter 2 is enabled, the delimiter function will not work properly.
Delimiter process
Setting
Factory Default
Necessity
Do nothing
Do Nothing
Optional
Delimiter + 1
Delimiter + 2
Strip Delimiter
[Delimiter + 1] or [Delimiter + 2]: The data will be transmitted when an additional byte (for Delimiter +1), or
an additional 2 bytes (for Delimiter +2) of data is received after receiving the Delimiter.
[Strip Delimiter]: When the Delimiter is received, the Delimiter is deleted (i.e., stripped), and the remaining
data is transmitted.
[Do nothing]: The data will be transmitted when the Delimiter is received.
Force transmit
Setting
Factory Default
Necessity
0 to 65535 ms
0 ms
Optional
0: Disable the force transmit timeout.
1 to 65535: Forces the NPort’s TCP/IP protocol software to try to pack serial data received during the specified
time into the same data frame.
This parameter defines the time interval during which the NPort fetches the serial data from its internal buffer.
If data is incoming through the serial port, the NPort stores the data in the internal buffer. The NPort transmits
data stored in the buffer via TCP/IP, but only if the internal buffer is full or if the force transmit time interval
reaches the time specified under Force Transmit timeout.
Optimal force transmit timeout differs according to your application, but it must be at least larger than one
character interval within the specified baudrate. For example, assume that the serial port is set to 1200 bps, 8
data bits, 1 stop bit, and no parity. In this case, the total number of bits needed to send a character is 10 bits,
and the time required to transfer one character is
10 (bits) / 1200 (bits/s) * 1000 (ms/s) = 8.3 ms.
Therefore, you should set Force Transmit timeout to be larger than 8.3 ms. Force Transmit timeout is specified
in milliseconds and must be larger than 10 ms.
If the user wants to send the series of characters in a packet, the serial device attached to the NPort should
send characters without time delay larger than Force Transmit timeout between characters and the total length
of data must be smaller than or equal to the NPort’s internal buffer size. The serial communication buffer size
of the NPort is 1 Kbytes per port.
Parameter Copy
Apply the above setting to other serial ports, you may use the checkboxes at the bottom of the window to apply
the settings to one or more ports.
5-11
NPort S8000 Series
Basic Settings and Device Server Configuration
RFC2217 Mode
Port Settings
TCP port (default=4001)
This is the TCP port number assignment for the serial port on the NPort S8000. It is the port number that the
serial port uses to listen to connections, and that other devices must use to contact the serial port. To avoid
conflicts with well known TCP ports, the default is set to 4001.
Data Packing
Packet length
Setting
Factory Default
Necessity
0 to 1024
0
Optional
Default = 0, The Delimiter Process will be followed, regardless of the length of the data packet. If the data
length (in bytes) matches the configured value, the data will be forced out. The data length can be configured
for 0 to 1024 bytes. Set to 0 if you do not need to limit the length.
Delimiter 1
Setting
Factory Default
Necessity
00 to FF
None
Optional
Setting
Factory Default
Necessity
00 to FF
None
Optional
Delimiter 2
When Delimiter 1 is enabled, the serial port will clear the buffer and send the data to the Ethernet port when
a specific character, entered in hex format, is received. A second delimiter character may be enabled and
specified in the Delimiter 2 field, so that both characters act as the delimiter to indicate when data should be
sent.
5-12
NPort S8000 Series
Basic Settings and Device Server Configuration
ATTENTION
Delimiter 2 is optional. If left blank, then Delimiter 1 alone trips clearing of the buffer. If the size of the serial
data received is greater than 1 KB, the NPort will automatically pack the data and send it to the Ethernet.
However, to use the delimiter function, you must at least enable Delimiter 1. If Delimiter 1 is left blank and
Delimiter 2 is enabled, the delimiter function will not work properly.
Delimiter process
Setting
Factory Default
Necessity
Do nothing
Do Nothing
Optional
Delimiter + 1
Delimiter + 2
Strip Delimiter
[Delimiter + 1] or [Delimiter + 2]: The data will be transmitted when an additional byte (for Delimiter +1), or
an additional 2 bytes (for Delimiter +2) of data is received after receiving the Delimiter.
[Strip Delimiter]: When the Delimiter is received, the Delimiter is deleted (i.e., stripped), and the remaining
data is transmitted.
[Do nothing]: The data will be transmitted when the Delimiter is received.
Force transmit
Setting
Factory Default
Necessity
0 to 65535 ms
0 ms
Optional
0: Disable the force transmit timeout.
1 to 65535: Forces the NPort’s TCP/IP protocol software to try to pack serial data received during the specified
time into the same data frame.
This parameter defines the time interval during which the NPort fetches the serial data from its internal buffer.
If data is incoming through the serial port, the NPort stores the data in the internal buffer. The NPort transmits
data stored in the buffer via TCP/IP, but only if the internal buffer is full or if the force transmit time interval
reaches the time specified under Force Transmit timeout.
Optimal force transmit timeout differs according to your application, but it must be at least larger than one
character interval within the specified baudrate. For example, assume that the serial port is set to 1200 bps, 8
data bits, 1 stop bit, and no parity. In this case, the total number of bits needed to send a character is 10 bits,
and the time required to transfer one character is
10 (bits) / 1200 (bits/s) * 1000 (ms/s) = 8.3 ms.
Therefore, you should set Force Transmit timeout to be larger than 8.3 ms. Force Transmit timeout is specified
in milliseconds and must be larger than 10 ms.
If the user wants to send the series of characters in a packet, the serial device attached to the NPort should
send characters without time delay larger than Force Transmit timeout between characters and the total length
of data must be smaller than or equal to the NPort’s internal buffer size. The serial communication buffer size
of the NPort is 1 Kbytes per port.
Parameter Copy
Apply the above setting to other serial ports, you may use the checkboxes at the bottom of the window to apply
the settings to one or more ports.
5-13
NPort S8000 Series
Basic Settings and Device Server Configuration
TCP Server Mode
Port Settings
Inactivity time
Setting
Factory Default
Necessity
0 to 65535 ms
0 ms
Optional
0 ms: TCP connection is not closed due to an idle serial line.
0-65535 ms: The NPort automatically closes the TCP connection if there is no serial data activity for the given
time. After the connection is closed, the NPort starts listening for another host’s TCP connection.
This parameter defines the maintenances status as Closed or Listen on the TCP connection. The connection is
closed if there is no incoming or outgoing data through the serial port during the specific Inactivity time.
If the value of inactivity time is set to 0, the current TCP connection is maintained until there is connection close
request. Although inactivity time is disabled, the NPort will check the connection status between the NPort and
remote host by sending “keep alive” packets periodically. If the remote host does not respond to the packet, it
assumes that the connection was closed down unintentionally. The NPort will then force the existing TCP
connection to close.
ATTENTION
The Inactivity time should at least be set larger than that of Force transmit timeout. To prevent the unintended
loss of data due to the session being disconnected, it is highly recommended that this value is set large enough
so that the intended data transfer is completed.
5-14
NPort S8000 Series
Basic Settings and Device Server Configuration
Max connection
Setting
Factory Default
Necessity
1, 2, 3, 4, 5, 6, 7, 8
1
Required
This field is used if you need to receive data from different hosts simultaneously. When set to 1, only one
specific host can access this port of the NPort S8000, and the Real COM driver on that host will have full control
over the port. When set to 2 or greater, up to the specified number of hosts’ Real COM drivers may open this
port at the same time. When multiple hosts’ Real COM drivers open the port at the same time, the COM driver
only provides a pure data tunnel—no control ability. The serial port parameters will use firmware settings
instead of depending on your application program (AP).
Application software that is based on the COM driver will receive a driver response of “success” when the
software uses any of the Win32 API functions. The firmware will only send data back to the driver on the host.
Data will be sent first-in-first-out when data enters the NPort S8000 from the Ethernet interface.
ATTENTION
When Max connection is set to 2 to 8, this means that the NPort will be using a “multi connection application”
(i.e., 2 to 8 hosts are allowed access to the port at the same time). When using a multi connection application,
the NPort will use the serial communication parameters set in the console. All of the hosts connected to that
port must use the same serial settings. If one of the hosts opens the COM port with parameters that are
different from the NPort’s console setting, data communication may not work properly.
Ignore jammed IP
Setting
Factory Default
Necessity
Enable or Disable
Disable
Optional
Previously, if “max connection” was greater than 1, the serial device was transmitting data, and a connected
host was not responding, the NPort would wait until the data was transmitted successfully before transmitting
the second group of data to all hosts. Currently, if you select Enable for “Ignore jammed IP,” the host that is not
responding will be ignored, but the data will still be transmitted to the other hosts.
Allow driver control
Setting
Factory Default
Necessity
Enable or Disable
Disable
Optional
If “max connection” is greater than 1, the NPort will ignore driver control commands from all connected hosts.
However, if you set “Allow driver control” to YES, control commands will be accepted. Note that since the NPort
S8000 may get configuration changes from multiple hosts, the most recent command received will take
precedence.
Connection goes down
Setting
Factory Default
Necessity
Always High or Always
Always High
Optional
Low
You can configure what happens to the RTS and DTR signals when the Ethernet connection goes down. For
some applications, serial devices need to know the Ethernet link status through RTS or DTR signals sent
through the serial port. Use always low if you want the RTS and DTR signal to change their state to low when
the Ethernet connection goes down. Use always high if you do not want the Ethernet connection status to
affect the RTS or DTR signals.
Data Packing
Packet length
Setting
Factory Default
Necessity
0 to 1024
0
Optional
5-15
NPort S8000 Series
Basic Settings and Device Server Configuration
Default = 0, The Delimiter Process will be followed, regardless of the length of the data packet. If the data
length (in bytes) matches the configured value, the data will be forced out. The data length can be configured
for 0 to 1024 bytes. Set to 0 if you do not need to limit the length.
Delimiter 1
Setting
Factory Default
Necessity
00 to FF
None
Optional
Delimiter 2
Setting
Factory Default
Necessity
00 to FF
None
Optional
When Delimiter 1 is enabled, the serial port will clear the buffer and send the data to the Ethernet port when
a specific character, entered in hex format, is received. A second delimiter character may be enabled and
specified in the Delimiter 2 field, so that both characters act as the delimiter to indicate when data should be
sent.
ATTENTION
Delimiter 2 is optional. If left blank, then Delimiter 1 alone trips clearing of the buffer. If the size of the serial
data received is greater than 1 KB, the NPort will automatically pack the data and send it to the Ethernet.
However, to use the delimiter function, you must at least enable Delimiter 1. If Delimiter 1 is left blank and
Delimiter 2 is enabled, the delimiter function will not work properly.
Delimiter process
Setting
Factory Default
Necessity
Do nothing
Do Nothing
Optional
Delimiter + 1
Delimiter + 2
Strip Delimiter
[Delimiter + 1] or [Delimiter + 2]: The data will be transmitted when an additional byte (for Delimiter +1), or
an additional 2 bytes (for Delimiter +2) of data is received after receiving the Delimiter.
[Strip Delimiter]: When the Delimiter is received, the Delimiter is deleted (i.e., stripped), and the remaining
data is transmitted.
[Do nothing]: The data will be transmitted when the Delimiter is received.
Force transmit
Setting
Factory Default
Necessity
0 to 65535 ms
0 ms
Optional
0: Disable the force transmit timeout.
1 to 65535: Forces the NPort’s TCP/IP protocol software to try to pack serial data received during the specified
time into the same data frame.
This parameter defines the time interval during which the NPort fetches the serial data from its internal buffer.
If data is incoming through the serial port, the NPort stores the data in the internal buffer. The NPort transmits
data stored in the buffer via TCP/IP, but only if the internal buffer is full or if the force transmit time interval
reaches the time specified under Force Transmit timeout.
Optimal force transmit timeout differs according to your application, but it must be at least larger than one
character interval within the specified baudrate. For example, assume that the serial port is set to 1200 bps, 8
data bits, 1 stop bit, and no parity. In this case, the total number of bits needed to send a character is 10 bits,
and the time required to transfer one character is
10 (bits) / 1200 (bits/s) * 1000 (ms/s) = 8.3 ms.
5-16
NPort S8000 Series
Basic Settings and Device Server Configuration
Therefore, you should set Force Transmit timeout to be larger than 8.3 ms. Force Transmit timeout is specified
in milliseconds and must be larger than 10 ms.
If the user wants to send the series of characters in a packet, the serial device attached to the NPort should
send characters without time delay larger than Force Transmit timeout between characters and the total length
of data must be smaller than or equal to the NPort’s internal buffer size. The serial communication buffer size
of the NPort is 1 Kbytes per port.
TCP Server Mode
Local TCP port
Setting
Factory Default
Necessity
1 to 65535
4001
Required
The TCP port that the NPort uses to listen to connections, and that other devices must use to contact the NPort.
To avoid conflicts with well known TCP ports, the default is set to 4001.
Command port
Setting
Factory Default
Necessity
1 to 65535
966
Optional
The Command port is the TCP port for listening to SSDK commands from the host. In order to prevent a TCP
port conflict with other applications, the user can adjust the command port to another port if needed. And SSDK
Commands will automatically check out the Command Port on the NPort so that the user does not need to
configure the program.
Parameter Copy
Apply the above setting to other serial ports, you may use the checkboxes at the bottom of the window to apply
the settings to one or more ports.
5-17
NPort S8000 Series
Basic Settings and Device Server Configuration
TCP Client Mode
Port Settings
Inactivity time
Setting
Factory Default
Necessity
0 to 65535 ms
0 ms
Optional
0 ms: TCP connection is not closed due to an idle serial line.
0-65535 ms: The NPort automatically closes TCP connection, if there is no serial data activity for the given
time.
This parameter defines the maintenance status as Closed or Listen on the TCP connection. The connection is
closed if there is no incoming or outgoing data through the serial port during the specific Inactivity time.
If the value of inactivity time is set to 0, the current TCP connection is maintained until there’s connection close
request. Although the inactivity time is disabled, the NPort will check the connection status between the NPort
and remote host by sending “keep alive” packets periodically. If the remote host does not respond to the
packets, it treats the connection as being down unintentionally. The NPort will then force the existing TCP
connection to close.
ATTENTION
The Inactivity time should at least be set larger than that of Force transmit timeout. To prevent the unintended
loss of data due to the session being disconnected, it is highly recommended that this value is set large enough
so that the intended data transfer is completed.
5-18
NPort S8000 Series
Basic Settings and Device Server Configuration
ATTENTION
Inactivity time is ONLY active when “TCP connect on” is set to “Any character.”
Ignore jammed IP
Setting
Factory Default
Necessity
Enable or Disable
Disable
Optional
Previously, if “max connection” was greater than 1, the serial device was transmitting data, and a connected
host was not responding, the NPort would wait until the data was transmitted successfully before transmitting
the second group of data to all hosts. Currently, if you select Enable for “Ignore jammed IP,” the host that is not
responding will be ignored, but the data will still be transmitted to the other hosts.
Data Packing
Packet length
Setting
Factory Default
Necessity
0 to 1024
0
Optional
Default = 0, The Delimiter Process will be followed, regardless of the length of the data packet. If the data
length (in bytes) matches the configured value, the data will be forced out. The data length can be configured
for 0 to 1024 bytes. Set to 0 if you do not need to limit the length.
Delimiter 1
Setting
Factory Default
Necessity
00 to FF
None
Optional
Setting
Factory Default
Necessity
00 to FF
None
Optional
Delimiter 2
When Delimiter 1 is enabled, the serial port will clear the buffer and send the data to the Ethernet port when
a specific character, entered in hex format, is received. A second delimiter character may be enabled and
specified in the Delimiter 2 field, so that both characters act as the delimiter to indicate when data should be
sent.
ATTENTION
Delimiter 2 is optional. If left blank, then Delimiter 1 alone trips clearing of the buffer. If the size of the serial
data received is greater than 1 KB, the NPort will automatically pack the data and send it to the Ethernet.
However, to use the delimiter function, you must at least enable Delimiter 1. If Delimiter 1 is left blank and
Delimiter 2 is enabled, the delimiter function will not work properly.
Delimiter process
Setting
Factory Default
Necessity
Do nothing
Do Nothing
Optional
Delimiter + 1
Delimiter + 2
Strip Delimiter
[Delimiter + 1] or [Delimiter + 2]: The data will be transmitted when an additional byte (for Delimiter +1), or
an additional 2 bytes (for Delimiter +2) of data is received after receiving the Delimiter.
[Strip Delimiter]: When the Delimiter is received, the Delimiter is deleted (i.e., stripped), and the remaining
data is transmitted.
[Do nothing]: The data will be transmitted when the Delimiter is received.
5-19
NPort S8000 Series
Basic Settings and Device Server Configuration
Force transmit
Setting
Factory Default
Necessity
0 to 65535 ms
0 ms
Optional
0: Disable the force transmit timeout.
1 to 65535: Forces the NPort’s TCP/IP protocol software to try to pack serial data received during the specified
time into the same data frame.
This parameter defines the time interval during which the NPort fetches the serial data from its internal buffer.
If data is incoming through the serial port, the NPort stores the data in the internal buffer. The NPort transmits
data stored in the buffer via TCP/IP, but only if the internal buffer is full or if the force transmit time interval
reaches the time specified under Force Transmit timeout.
Optimal force transmit timeout differs according to your application, but it must be at least larger than one
character interval within the specified baudrate. For example, assume that the serial port is set to 1200 bps, 8
data bits, 1 stop bit, and no parity. In this case, the total number of bits needed to send a character is 10 bits,
and the time required to transfer one character is
10 (bits) / 1200 (bits/s) * 1000 (ms/s) = 8.3 ms.
Therefore, you should set Force Transmit timeout to be larger than 8.3 ms. Force Transmit timeout is specified
in milliseconds and must be larger than 10 ms.
If the user wants to send the series of characters in a packet, the serial device attached to the NPort should
send characters without time delay larger than Force Transmit timeout between characters and the total length
of data must be smaller than or equal to the NPort’s internal buffer size. The serial communication buffer size
of the NPort is 1 Kbytes per port.
TCP Client Mode
Destination IP address 1
Setting
Factory Default
Necessity
IP address or Domain
None
Required
Address
(E.g., 192.168.1.1)
Allows the NPort to connect actively to the remote host whose address is set by this parameter.
Destination IP address 2/3/4
Setting
Factory Default
Necessity
IP address or Domain
None
Required
Address
(E.g., 192.168.1.1)
Allows the NPort to connect actively to the remote host whose address is set by this parameter.
TCP port (default=4001): This is the TCP port number assignment for the serial port on the NPort S8000. It is
the port number that the serial port uses to listen to connections, and that other devices must use to contact
the serial port. To avoid conflicts with well known TCP ports, the default is set to 4001.
ATTENTION
Up to 4 connections can be established between the NPort and hosts. The connection speed or throughput may
be low if one of the four connections is slow, since the slow connection will slow down the other 3 connections.
ATTENTION
The “Destination IP address” parameter can use both IP address and Domain Name. For some applications, the
user may need to send the data actively to the remote destination domain name.
5-20
NPort S8000 Series
Basic Settings and Device Server Configuration
Designated Local Port 1/2/3/4
Setting
Factory Default
Necessity
TCP Port No.
5001 (Port 1)
Required
5002 (Port 2)
5003 (Port 3)
5004 (Port 4)
Connection control
Setting
Factory Default
Necessity
Startup/None,
Startup/None
Required
Any Character/None,
Any
Character/Inactivity
Time,
DSR ON/DSR OFF,
DSR ON/None,
DCD ON/DCD OFF,
DCD ON/None
The meaning of each of the above settings is given in the table below. In general, both the Connect condition
and Disconnect condition are given.
TCP Connection on
Connect/Disconnect
Description
Startup/None
A TCP connection will be established on startup, and will remain active
(default)
indefinitely.
Any Character/None
A TCP connection will be established when any character is received from the
serial interface, and will remain active indefinitely.
Any Character/
A TCP connection will be established when any character is received from the
Inactivity Time
serial interface, and will be disconnected when the Inactivity time out is reached.
DSR On/DSR Off
A TCP connection will be established when a DSR “On” signal is received, and will
be disconnected when a DSR “Off” signal is received.
DSR On/None
A TCP connection will be established when a DSR “On” signal is received, and will
remain active indefinitely.
DCD On/DCD Off
A TCP connection will be established when a DCD “On” signal is received, and will
be disconnected when a DCD “Off” signal is received.
DCD On/None
A TCP connection will be established when a DCD “On” signal is received, and will
remain active indefinitely.
Parameter Copy
Apply the above setting to other serial ports, you may use the checkboxes at the bottom of the window to apply
the settings to one or more ports.
5-21
NPort S8000 Series
Basic Settings and Device Server Configuration
UDP Mode
Data Packing
Packing length
Setting
Factory Default
Necessity
0 to 1024
0
Optional
Default = 0, The Delimiter Process will be followed, regardless of the length of the data packet. If the data
length (in bytes) matches the configured value, the data will be forced out. The data length can be configured
for 0 to 1024 bytes. Set to 0 if you do not need to limit the length.
Delimiter 1
Setting
Factory Default
Necessity
00 to FF
None
Optional
Setting
Factory Default
Necessity
00 to FF
None
Optional
Delimiter 2
When Delimiter 1 is enabled, the serial port will clear the buffer and send the data to the Ethernet port when
a specific character, entered in hex format, is received. A second delimiter character may be enabled and
specified in the Delimiter 2 field, so that both characters act as the delimiter to indicate when data should be
sent.
ATTENTION
Delimiter 2 is optional. If left blank, then Delimiter 1 alone trips clearing of the buffer. If the size of the serial
data received is greater than 1 KB, the NPort will automatically pack the data and send it to the Ethernet.
However, to use the delimiter function, you must at least enable Delimiter 1. If Delimiter 1 is left blank and
Delimiter 2 is enabled, the delimiter function will not work properly.
5-22
NPort S8000 Series
Basic Settings and Device Server Configuration
Delimiter process
Setting
Factory Default
Necessity
Do nothing
Do Nothing
Optional
Delimiter + 1
Delimiter + 2
Strip Delimiter
[Delimiter + 1] or [Delimiter + 2]: The data will be transmitted when an additional byte (for Delimiter +1), or
an additional 2 bytes (for Delimiter +2) of data is received after receiving the Delimiter.
[Strip Delimiter]: When the Delimiter is received, the Delimiter is deleted (i.e., stripped), and the remaining
data is transmitted.
[Do nothing]: The data will be transmitted when the Delimiter is received.
Force transmit
Setting
Factory Default
Necessity
0 to 65535 ms
0 ms
Optional
0: Disable the force transmit timeout.
1 to 65535: Forces the NPort’s TCP/IP protocol software to try to pack serial data received during the specified
time into the same data frame.
This parameter defines the time interval during which the NPort fetches the serial data from its internal buffer.
If data is incoming through the serial port, the NPort stores the data in the internal buffer. The NPort transmits
data stored in the buffer via TCP/IP, but only if the internal buffer is full or if the force transmit time interval
reaches the time specified under Force Transmit timeout.
Optimal force transmit timeout differs according to your application, but it must be at least larger than one
character interval within the specified baudrate. For example, assume that the serial port is set to 1200 bps, 8
data bits, 1 stop bit, and no parity. In this case, the total number of bits needed to send a character is 10 bits,
and the time required to transfer one character is
10 (bits) / 1200 (bits/s) * 1000 (ms/s) = 8.3 ms.
Therefore, you should set Force Transmit timeout to be larger than 8.3 ms. Force Transmit timeout is specified
in milliseconds and must be larger than 10 ms.
If the user wants to send the series of characters in a packet, the serial device attached to the NPort should
send characters without time delay larger than Force Transmit timeout between characters and the total length
of data must be smaller than or equal to the NPort’s internal buffer size. The serial communication buffer size
of the NPort is 1 Kbytes per port.
UDP Mode
Destination IP address 1
Setting
Factory Default
Necessity
IP address range
Begin:
Empty
Required
E.g., Begin: 192.168.1.1
End:
Empty
Port:
4001
End: 192.168.1.10
Destination IP address 2/3/4
Setting
Factory Default
Necessity
IP address range
Begin:
Empty
Optional
E.g., Begin: 192.168.1.11
End:
Empty
Port:
4001
End: 192.168.1.20
Local listen port
Setting
Factory Default
Necessity
1 to 65535
4001
Required
5-23
NPort S8000 Series
Basic Settings and Device Server Configuration
The UDP port that the NPort listens to, and that other devices must use to contact the NPort. To avoid conflicts
with well known UDP ports, the default is set to 4001.
Parameter Copy
Apply the above setting to other serial ports, you may use the checkboxes at the bottom of the window to apply
the settings to one or more ports.
Disabled Mode
When Operation mode is set to Disabled, that particular port will be disabled. Check the “Apply the above
settings to all serial ports” to apply this setting to the other port.
Apply the above setting to other serial ports, you may use the checkboxes at the bottom of the window to apply
the settings to one or more ports.
Serial Parameters
Port alias
Setting
Factory Default
Necessity
1 to 16 characters
None
Optional
(E.g., PLC-No.1)
Port Alias is specially designed to allow easy identification of the serial devices which are connected to the
NPort’s serial port.
Baud rate
Setting
Factory Default
Necessity
50 bps to 921600 bps
115200 bps
Required
5-24
NPort S8000 Series
Basic Settings and Device Server Configuration
Select one of the standard baudrates from 50 bps to 921.6 Kbps inthe dropdown box, or select Other and then
type the desired baudrate in the input box.
ATTENTION
If the port requires a special baudrate that is not listed, such as 500000 bps, you may can select the Other
option and enter the desired baudrate into the text box. The NPort S8000 will automatically calculate the
closest supported baudrate. The margin for error will be less than 1.7% for all baudrates under 921600 bps.
Parity
Setting
Factory Default
Necessity
None, Even, Odd,
None
Required
Setting
Factory Default
Necessity
5, 6, 7, 8
8
Required
Space, Mark
Data bits
When the user sets Data bits to 5 bits, the stop bits setting will automatically change to 1.5 bits.
Stop bits
Setting
Factory Default
Necessity
1, 2
1
Required
Stop bits will be set to 1.5 when Data bits is set to 5 bits.
Flow control
Setting
Factory Default
Necessity
None, RTS/CTS,
RTS/CTS
Required
Xon/Xoff
FIFO
Setting
Factory Default
Necessity
Enable, Disable
Enable
Required
The NPort’s serial ports provide a 16-byte FIFO both in the Tx and Rx directions. Disable the FIFO setting when
your serial device does not have a FIFO to prevent data loss during communication.
Interface
Setting
Factory Default
Necessity
RS-232, RS-422,
RS-232
Required
RS-485 2-wire, RS-485
4-wire
ATTENTION
Check the serial communication parameters in your serial device’s user’s manual. You should set up the NPort’s
serial parameters with the same communication parameters used by your serial devices.
5-25
NPort S8000 Series
Basic Settings and Device Server Configuration
Serial ToS Settings
Using Serial Traffic Prioritization
The NPort S8000’s traffic prioritization capability provides Quality of Service (QoS) to your network by making
data delivery more reliable. You can prioritize traffic from both serial interface and Ethernet interface on your
network to ensure that high priority data is transmitted with minimum delay.
Traffic can be controlled by a set of rules to obtain the required Quality of Service for your network. The rules
define different types of traffic and specify how each type should be treated as it passes through the NPort
S8000. The NPort S8000 can inspect layer 3 TOS information to each serial port to provide consistent
classification of the entire network. The NPort S8000’s QoS capability improves the performance and
determinism of industrial networks for mission critical applications.
The Serial Traffic Prioritization Concept
What is Traffic Prioritization?
Traffic prioritization allows you to prioritize data so that time-sensitive and system-critical data can be
transferred smoothly and with minimal delay over a network. The benefits of using traffic prioritization are:
•
Improve network performance by controlling a wide variety of traffic and managing congestion.
•
Assign priorities to different categories of traffic. For example, set higher priorities for time-critical or
business-critical applications.
•
Provide predictable throughput for multimedia applications, such as video conferencing or voice over IP,
and minimize traffic delay and jitter.
•
Improve network performance as the amount of traffic grows. This will save cost by reducing the need to
keep adding bandwidth to the network.
DiffServ Code Point (DSCP)
Differentiated Services (DiffServ) Traffic Marking
DiffServ is a Layer 3 marking scheme that uses the DiffServ Code Point (DSCP) field in the IP header to store
the packet priority information. DSCP is an advanced intelligent method of traffic marking as you can choose
how your network prioritizes different types of traffic. DSCP uses 64 values that map to user-defined service
5-26
NPort S8000 Series
Basic Settings and Device Server Configuration
levels, allowing you to establish more control over network traffic. Please reference to “ToS/DiffServ Mapping”
setting menu.
DSCP Value
00
04
08
0C
10
14
18
1C
20
24
28
2C
30
34
38
3C
40
44
48
4C
50
54
58
5C
60
64
68
6C
70
74
78
7C
80
84
88
8C
90
94
98
9C
A0
A4
A8
AC
B0
B4
B8
BC
C0
C4
C8
CC
D0
D4
D8
DC
0E
E4
E8
EC
F0
F4
F8
FC
Enter the “ToS/DiffServ Mapping” setting menu to reference or modified the ToS level.
Setting
Description
Enable ToS
Enable the ToS transmitting the video stream Disable
Factory Default
Necessity
Optional
with the given priority
DSCP Value
Set the mapping table of different TOS values 0,0
Optional
to 4 different egress queues.
ATTENTION
To configure the ToS values, map to the network environment settings for QoS priority service. Please refer to
Chapter 6, Ethernet Advanced Settings / Configuring Ethernet Traffic Prioritization / CoS Mapping.
5-27
6
6.
Switch Featured Functions
This chapter explains how to access the NPort S8000’s various configuration, monitoring, and administration
functions. There are three ways to access these functions: RS-232 console, Telnet console, and web browser.
The serial console connection method, which requires using a short serial cable to connect the NPort S8000 to
a PC’s COM port, can be used if you do not know the NPort S8000’s IP address. The Telnet console and web
browser connection methods can be used to access the NPort S8000 over an Ethernet LAN, or over the
Internet.
The Web Console is the most user-friendly way to configure the NPort S8000. In this chapter, we use the Web
Console interface to introduce the functions. There are only a few differences between the Web Console, Serial
Console, and Telnet Console.
The following topics are covered in this chapter:
 Ethernet Settings
 STP/RSTP
 Bandwidth Management
 Line Swap Fast Recovery
 Ethernet Advanced Settings
 Virtual LAN
 Multicast Filtering
 Set Device IP
 System Management
 SysLog Server
 Port Access Control
 Configuring E-Mail Alert
 Configuring SNMP
 Maintenance
 System Monitoring
 Restart
NPort S8000 Series
Switch Featured Functions
Ethernet Settings
Port Settings
Enable
Setting
Description
Factory Default
Checked
Allows data transmission through the port.
Enabled
Unchecked
Immediately shuts off port access.
ATTENTION
If a connected device or sub-network is wreaking havoc on the rest of the network, the Disable option under
Advanced Settings/Port gives the administrator a quick way to shut off access through this port immediately.
Description
Setting
Description
Factory Default
Media type
Displays the media type for each module’s port
N/A
Setting
Description
Factory Default
Max. 63 Characters
Specify an alias for each port, and assist the administrator in
None
Name
remembering important information about the port.
E.g., PLC 1
Speed (Copper Port Only )
Setting
Description
Factory Default
Auto
Allows the port to use the IEEE 802.3u protocol to negotiate
Auto
with connected devices. The port and connected devices will
determine the best speed for that connection.
100M-Full
Choose one of these fixed speed options if the opposing
100M-Half
Ethernet device has trouble auto-negotiating line speed.
10M-Full
10M-Half
FDX Flow Ctrl.
This setting enables or disables the flow control capability of this port when the “port transmission speed”
setting is in “auto” mode. The final result will be determined by the “auto” process between the NPort S8000
and connected devices.
Setting
Description
Factory Default
Enable
Enables flow control for this port when in auto-negotiate mode. Disable
Disable
Disables flow control for this port when in auto-negotiate mode.
6-2
NPort S8000 Series
Switch Featured Functions
MDI/MDIX
Setting
Description
Factory Default
Auto
Allows the port to auto detect the port type of the opposing
Auto
Ethernet device and change the port type accordingly.
MDI
Choose the MDI or MDIX option if the opposing Ethernet device
MDIX
has trouble auto-negotiating port type.
Port Trunking
Using Port Trunking
Link Aggregation allows one or more links to be aggregated together to form a Link Aggregation Group. A MAC
client can treat Link Aggregation Groups as if they were a single link.
NPort S8000’s Port Trunking feature allows devices to communicate by aggregating up to 2 trunk groups on the
NPort S8000. If one of the ports fails, the other ports in the same trunk group will provide back up and share
the traffic automatically.
The Port Trunking Concept
Moxa has developed a proprietary Port Trunking protocol that provides the following benefits:
•
Gives you more flexibility in setting up your network connections, since the bandwidth of a link can be
doubled, tripled, or quadrupled.
•
Provides redundancy—if one link is broken, the remaining trunked ports share the traffic within this trunk
group.
•
Load sharing—MAC Client traffic may be distributed across multiple links.
•
To avoid broadcast storms or loops in your network while configuring a trunk, first disable or disconnect all
ports that you want to add to the trunk or remove from the trunk. After you finish configuring the trunk,
enable or re-connect the ports.
If all ports on both switches are configured as 100BASE-TX and they are operating in full duplex, the potential
bandwidth of the connection will be up to 1 Gbps on an NPort S8000- switching device server. This means that
users can connect one NPort S8000 to another NPort S8000 by port trunking to double, triple, or quadruple the
bandwidth of the connection.
When configuring Port Trunking, note that:
Each NPort S8000 can set a maximum of 2 Port Trunking groups (designated Trk1, Trk2).
When you activate Port Trunking settings, some advanced functions that you setup with the original ports will
either be set to factory default values, or disabled:
•
Communication Redundancy will be set to the factory default
•
Traffic Prioritization will be set to the factory default
•
Port-based VLAN or 802.1Q VLAN will be set to the factory default
•
Multicast Filtering will be set to the factory default
•
Rate Limiting will be set to the factory default
•
Port Access Control will be set to the factory default
•
Email and Relay Warning will be set to the factory default
•
Set Device IP will be set to the factory default
•
Mirror Port will be set to the factory default
•
You can setup these features again on your Trunking Port.
6-3
NPort S8000 Series
Switch Featured Functions
The Port Trunking Settings page is used to assign ports to a Trunk Group.
1. Select Trk1, Trk2 from the Trunk Group drop-down box.
2. Select Static, or LACP from the Trunk Type drop-down box.
3. Under Member Ports and Available Ports, select the specific ports.
4. Use the Up / Down buttons to add/remove designated ports to/from a trunk group.
Trunk Group (Maximum of 2 trunk groups on NPort S8000
Setting
Description
Factory Default
Trk1, Trk2 on NPort
Display or designate the Trunk Type and Member Ports for
Trk1
S8000-
Trunk Groups 1, 2
Trunk Type
Setting
Description
Factory Default
Static
Designated Moxa proprietary trunking protocol
Static
LACP
Designated LACP (IEEE 802.3ad, Link Aggregation Control
Static
Protocol)
Available Ports/Member Port
Setting
Description
Factory Default
Member/Available
Use Up/Down buttons to add/remove specific ports from
N/A
Ports
available ports to/from trunk group.
Check box
Check to designate which ports to add or remove.
Unchecked
Port
Port number
N/A
Port description
Displays the media type for each module’s port
N/A
Name
Max. 63 Characters
N/A
Speed
Indicates the transmission speed (100M-Full, 100M-Half,
N/A
10M-Full, or 10M-Half)
FDX Flow Control
Indicates if the FDX flow control of this port is “Enabled” or
N/A
“Disabled.”
Up
Add designated ports into trunk group from available ports.
N/A
Down
Remove designated ports from trunk group to available port.
N/A
Communication Redundancy
Using Communication Redundancy
Setting up Communication Redundancy on your network helps protect critical links against failure, protects
against network loops, and keeps network downtime at a minimum.
6-4
NPort S8000 Series
Switch Featured Functions
The Communication Redundancy function allows the user to set up redundant loops in the network to provide
a backup data transmission route in the event that a cable is inadvertently disconnected or damaged. This
feature is particularly important for industrial applications, since it could take several minutes to locate the
disconnected or severed cable. For example, if the NPort S8000 is used as a key communications component
of a production line, several minutes of downtime could result in a big loss in production and revenue. The NPort
S8000 supports three different protocols to support this communication redundancy function— Rapid
Spanning Tree/ Spanning Tree Protocol (IEEE 802.1W/1D), Turbo Ring, and Turbo Ring V2.
When configuring a redundant ring, all NPort S8000s on the same ring must be configured to use the same
redundancy protocol. You cannot mix the “Turbo Ring,” “Turbo Ring V2,” and RSTP protocols on the same ring.
The following table lists the key differences between each feature. Use this information to evaluate the benefits
of each, and then determine which features are most suitable for your network.
NOTE
Turbo Ring V2
Turbo Ring
RSTP
Topology
Ring
Ring
Ring, Mesh
Recovery Time
< 20 ms
< 300 ms
Up to 5 sec
Most of Moxa’s managed switches now support two proprietary Turbo Ring protocols:
“Turbo Ring” refers to the original version of Moxa’s proprietary redundant ring protocol, which has a recovery
time of under 300 ms.
“Turbo Ring V2” refers to the new generation Turbo Ring, which has a recovery time of under 20 ms.
In this manual, we use the terminology “Turbo Ring” ring and “Turbo Ring V2” ring to differentiate between
rings configured for one or the other of these protocols.
The Turbo Ring Concept
Moxa developed the proprietary Turbo Ring protocol to optimize communication redundancy and achieve a
faster recovery time on the network.
The Turbo Ring and Turbo Ring V2 protocols identify one NPort S8000 as the master of the network, and then
automatically block packets from traveling through any of the network’s redundant loops. In the event that one
branch of the ring gets disconnected from the rest of the network, the protocol automatically readjusts the ring
so that the part of the network that was disconnected can reestablish contact with the rest of the network.
Initial setup of a “Turbo Ring” or “Turbo Ring V2” ring
1. For each NPort S8000 in the ring, select any two ports as the
redundant ports.
2. Connect redundant ports on neighboring NPort S8000 or
switches to form the redundant ring.
The user does not need to configure any of the NPort S8000 or switches as the master to use Turbo Ring or
Turbo Ring V2. If none of the NPort S8000 switches in the ring is configured as the master, then the protocol
will automatically assign master status to one of the switches. In fact, the master is only used to identify which
segment in the redundant ring acts as the backup path. In the following subsections, we explain how the
redundant path is selected for rings configured for Turbo Ring, and Turbo Ring V2.
6-5
NPort S8000 Series
Switch Featured Functions
Determining the Redundant Path of a “Turbo Ring” Ring
In this case, the redundant segment (i.e., the segment that will be blocked during normal operation) is
determined by the number of NPort S8000 that make up the ring, and where the ring master is located.
“Turbo Ring” rings with an even number of NPort S8000
If there are 2N NPort S8000 (an even number) in the
“Turbo Ring” ring, then the backup segment is one of the
two segments connected to the (N+1)st NPort S8000
(i.e., the NPort S8000 unit directly opposite the master).
“Turbo Ring” rings with an odd number of NPort S8000
If there are 2N+1 NPort S8000 (an odd number) in the
“Turbo Ring” ring, with NPort S8000 and segments
labeled counterclockwise, then segment N+1 will serve
as the backup path.
For the example shown here, N=1, so that N+1=2.
Determining the Redundant Path of a “Turbo Ring V2” Ring
For a “Turbo Ring V2” ring, the backup segment is the
segment connected to the 2nd redundant port on the
master.
See Configuring “Turbo Ring V2” in the Configuring
“Turbo Ring” and “Turbo Ring V2” section below.
Ring Coupling Configuration
For some systems, it may not be convenient to connect all devices in the system to create one BIG redundant
ring, since some devices could be located in a remote area. For these systems, “Ring Coupling” can be used to
6-6
NPort S8000 Series
Switch Featured Functions
separate the devices into different smaller redundant rings, but in such a way that they can still communicate
with each other.
ATTENTION
In a VLAN environment, the user must set “Redundant Port,” “Coupling Port,” and “Coupling Control Port” to
join all VLANs, since these ports act as the “backbone” to transmit all packets of different VLANs to different
NPort S8000.
Ring Coupling for a “Turbo Ring” Ring
To configure the Ring Coupling function for a “Turbo Ring” ring, select two NPort S8000 (e.g., Switch A and B
in the above figure) in the ring, and another two NPort S8000 in the adjacent ring (e.g., Switch C and D).
Decide which two ports in each switch are appropriate to be used as coupling ports, and then link them together.
Next, assign one switch (e.g., Switch A) to be the “coupler,” and connect the coupler’s coupling control port
with Switch B (for this example).
The coupler switch (i.e., Switch A) will monitor switch B through the coupling control port to determine whether
or not the coupling port’s backup path should be recovered.
Ring Coupling for a “Turbo Ring V2” Ring
Note that the ring coupling settings for a “Turbo Ring V2” ring are different from a “Turbo Ring” ring. For Turbo
Ring V2, Ring Coupling is enabled by configuring the “Coupling Port (Primary)” on Switch B, and the “Coupling
Port (Backup)” on Switch A only. You do not need to set up a coupling control port, so that a “Turbo Ring V2”
ring does not use a coupling control line.
The “Coupling Port (Backup)” on Switch A is used for the backup path, and connects directly to an extra
network port on Switch C. The “Coupling Port (Primary)” on Switch B monitors the status of the main path, and
connects directly to an extra network port on Switch D. With ring coupling established, Switch A can activate
the backup path as soon as it detects a problem with the main path.
6-7
NPort S8000 Series
Switch Featured Functions
ATTENTION
Ring Coupling only needs to be enabled on one of the switches serving as the Ring Coupler. The Coupler must
designate different ports as the two Turbo Ring ports and the coupling port.
NOTE
You do not need to use the same NPort S8000 unit for both Ring Coupling and Ring Master.
Dual-Ring Configuration (applies only to “Turbo Ring V2”)
The “dual-ring” option provides another ring coupling configuration, in which two adjacent rings share one
switch. This type of configuration is ideal for applications that have inherent cabling difficulties.
Dual-Ring for a “Turbo Ring V2” Ring
Dual-Homing Configuration (applies only to “Turbo Ring V2”)
The “dual-homing” option uses a single Ethernet switch to connect two networks. The primary path is the
operating connection, and the backup path is a back-up connection that is activated in the event that the
primary path connection fails.
Dual-Homing for a “Turbo Ring V2” Ring
Configuring “Turbo Ring” and “Turbo Ring V2”
Use the Communication Redundancy page to configure select “Turbo Ring” or “Turbo Ring V2.” Note that
configuration pages for these two protocols are different.
6-8
NPort S8000 Series
Switch Featured Functions
Configuring “Turbo Ring”
NOTE
The user does not need to set the master to use Turbo Ring. If no master is set, the Turbo Ring protocol will
assign master status to one of the NPort S8000 in the ring. The master is only used to determine which
segment serves as the backup path.
Redundancy Protocol
Setting
Description
Turbo Ring
Select this item to change to the Turbo Ring configuration page. Turbo Ring V2
Factory Default
Turbo Ring V2
Select this item to change to the Turbo Ring V2 configuration
RSTP (IEEE
Select this item to change to the RSTP configuration page.
page.
802.1W/1D)
Set as Master
Setting
Description
Factory Default
Enabled
Select this NPort S8000 as Master
Not checked
Disabled
Do not select this NPort S8000 as Master
Redundant Ports
Setting
Description
Factory Default
1st Port
Select any port of the NPort S8000 to be one of the redundant Port 4
ports.
2nd Port
Select any port of the NPort S8000 to be one of the redundant Port 5
ports.
Enable Ring Coupling
Setting
Description
Factory Default
Enable
Select this NPort S8000 as Coupler
Not checked
Disable
Do not select this NPort S8000 as Coupler
Coupling Port
Setting
Description
Factory Default
Coupling Port
Select any port of the NPort S8000 to be the coupling port
port 2
6-9
NPort S8000 Series
Switch Featured Functions
Coupling Control Port
Setting
Description
Factory Default
Coupling Control Port
Select any port of the NPort S8000 to be the coupling control
port 3
port
Configuring “Turbo Ring V2”
NOTE
When using the Dual-Ring architecture, users must configure settings for both Ring 1 and Ring 2. In this case,
the status of both rings will appear under “Current Status.”
NOTE
The user does not need to set the master to use Turbo Ring. If no master is set, the Turbo Ring protocol will
assign master status to one of the NPort S8000 in the ring. The master is only used to determine which
segment serves as the backup path.
Redundancy Protocol
Setting
Description
Turbo Ring
Select this item to change to the Turbo Ring configuration page. RSTP
Factory Default
Turbo Ring V2
Select this item to change to the Turbo Ring V2 configuration
page.
RSTP (IEEE
Select this item to change to the RSTP configuration page.
802.1W/1D)
Enable Ring 1
Setting
Description
Factory Default
Enabled
Enable the Ring 1 settings
Not checked
Disabled
Disable the Ring 1 settings
Enable Ring 2*
Setting
Description
Factory Default
Enabled
Enable the Ring 2 settings
Not checked
Disabled
Disable the Ring 2 settings
*You should enable both Ring 1 and Ring 2 when using the Dual-Ring architecture.
6-10
NPort S8000 Series
Switch Featured Functions
Set as Master
Setting
Description
Factory Default
Enabled
Select this NPort S8000 as Master
Not checked
Disabled
Do not select this NPort S8000 as Master
Redundant Ports
Setting
Description
1st Port
Select any port of the NPort S8000 to be one of the redundant Ring 1: port 4
Factory Default
ports.
2nd Port
Ring 2: port 5
Select any port of the NPort S8000 to be one of the redundant Ring 1: port 2
ports.
Ring 2: port 3
Enable Ring Coupling
Setting
Description
Factory Default
Enable
Select this NPort S8000 as Coupler
Not checked
Disable
Do not select this NPort S8000 as Coupler
Coupling Mode
Setting
Description
Factory Default
Dual Homing
Select this item to change to the Dual Homing configuration
Primary Port:
page
2
Backup Port:
port
port
3
Ring Coupling
Select this item to change to the Ring Coupling (backup)
Coupling Port : Port
(backup)
configuration page
2
Ring Coupling
Select this item to change to the Ring Coupling (primary)
Coupling Port : Port
(primary)
configuration page
2
Setting
Description
Factory Default
Primary Port
Select any port of the NPort S8000 to be the primary port.
port 2
Backup Port
Select any port of the NPort S8000 to be the backup port.
port 3
Primary/Backup Port
The Turbo Chain Concept
Moxa’s Turbo Chain is an advanced software-technology that gives network administrators the flexibility of
constructing any type of redundant network topology. When using the “chain” concept, you first connect the
Ethernet switches in a chain and then simply link the two ends of the chain to an Ethernet network, as
illustrated in the following figure.
Turbo Chain can be used on industrial networks that have a complex topology. If the industrial network uses a
multi-ring architecture, Turbo Chain can be used to create flexible and scalable topologies with a fast
media-recovery time.
6-11
NPort S8000 Series
Switch Featured Functions
Setting up Turbo Chain
1. Select the Head switch, Tail switch, and Member switches.
2. Configure one port as the Head port and one port as the Member port in the Head switch, configure one port
as the Tail port and one port as the Member port in the Tail switch, and configure two ports as Member ports
in each of the Member switches.
3. Connect the Head switch, Tail switch, and Member switches as shown in the diagram.
The path connecting to the Head port is the main path, and the path connecting to the Tail port is the back up
path of the Turbo Chain. Under normal conditions, packets are transmitted through the Head Port to the LAN
Network. If any Turbo Chain path is disconnected, the Tail Port will be activated to continue packet
transmission.
Configuring “Turbo Chain”
Head Switch Configuration
6-12
NPort S8000 Series
Switch Featured Functions
Member Switch Configuration
Tail Switch Configuration
Current Status
Now Active
Shows which communication protocol is in use: Turbo Ring, Turbo Ring V2, RSTP, Turbo Chain or None.
The “Ports Status” indicators show Forwarding for normal transmission, Blocked if this port is connected to
the Tail port as a backup path and the path is blocked, and Link down if there is no connection.
Settings
Redundancy Protocol
Setting
Description
Turbo Ring
Select this item to change to the Turbo Ring configuration page. None
Factory Default
Turbo Ring V2
Select this item to change to the Turbo Ring V2 configuration
page.
Turbo Chain
Select this item to change to the Turbo Chain configuration
page
RSTP (IEEE
Select this item to change to the RSTP configuration page.
802.1W/1D)
None
Ring redundancy is not active
Role
Setting
Description
Factory Default
Head
Select this EDS as Head Switch
Member
6-13
NPort S8000 Series
Switch Featured Functions
Member
Select this EDS as Member Switch
Tail
Select this EDS as Tail Switch
Head Role
Setting
Description
Factory Default
Head Port
Select any port of the EDS to be the head port.
EDS-505A: port 4
EDS-508A: port 7
Member Port
Select any port of the EDS to be the member port.
EDS-505A: port 5
EDS-508A: port 8
Member Role
Setting
Description
Factory Default
1st Member port
Select any port of the EDS to be the 1st member port
EDS-505A: port 4
2nd Member port
Select any port of the EDS to be the 2nd member port
EDS-508A: port 7
EDS-505A: port 5
EDS-508A: port 8
Tail Role
Setting
Description
Factory Default
Tail Port
Select any port of the EDS to be the tail port.
EDS-505A: port 4
Member Port
Select any port of the EDS to be the member port.
EDS-508A: port 7
EDS-505A: port 5
EDS-508A: port 8
STP/RSTP
The STP/RSTP Concept
Spanning Tree Protocol (STP) was designed to help reduce link failures in a network, and provide protection
from loops. Networks that have a complicated architecture are prone to broadcast storms caused by
unintended loops in the network. The NPort S8000’s STP feature is disabled by default. To be completely
effective, you must enable RSTP/STP on every NPort S8000 connected to your network.
Rapid Spanning Tree Protocol (RSTP) implements the Spanning Tree Algorithm and Protocol defined by IEEE
Std 802.1w-2001. RSTP provides the following benefits:
•
The topology of a bridged network will be determined much more quickly compared to STP.
•
RSTP is backward compatible with STP, making it relatively easy to deploy. For example:
 Defaults to sending 802.1D style BPDUs if packets with this format are received.
 STP (802.1D) and RSTP (802.1w) can operate on different ports of the same NPort S8000. This feature
is particularly helpful when the NPort S8000’s ports connect to older equipment, such as legacy
switches.
You get essentially the same functionality with RSTP and STP. To see how the two systems differ, see the
Differences between RSTP and STP section in this chapter.
NOTE
The STP protocol is part of the IEEE Std 802.1D, 1998 Edition bridge specification. The following explanation
uses bridge instead of switch.
What is STP?
STP (802.1D) is a bridge-based system that is used to implement parallel paths for network traffic. STP uses a
loop-detection process to:
•
Locate and then disable less efficient paths (i.e., paths that have a lower bandwidth).
6-14
NPort S8000 Series
•
Switch Featured Functions
Enable one of the less efficient paths if the most efficient path fails.
LAN 1
Bridge B
Bridge A
LAN 2
Bridge C
LAN 3
The figure below shows a network made up of three LANs separated by three bridges. Each segment uses at
most two paths to communicate with the other segments. Since this configuration can give rise to loops, the
network will overload if STP is NOT enabled.
If STP is enabled, it will detect duplicate paths and prevent, or block, one of them from forwarding traffic. In the
following example, STP determined that traffic from LAN segment 2 to LAN segment 1 should flow through
Bridges C and A because this path has a greater bandwidth and is therefore more efficient.
LAN 1
Bridge B
Bridge A
LAN 2
Bridge C
LAN 3
LAN 1
Bridge B
Bridge A
LAN 2
Bridge C
LAN 3
What happens if a link failure is detected? As shown in next figure, the STP process reconfigures the network
so that traffic from LAN segment 2 flows through Bridge B.
STP will determine which path between each bridged segment is most efficient, and then assigns a specific
reference point on the network. When the most efficient path has been identified, the other paths are blocked.
In the previous 3 figures, STP first determined that the path through Bridge C was the most efficient, and as a
6-15
NPort S8000 Series
Switch Featured Functions
result, blocked the path through Bridge B. After the failure of Bridge C, STP re-evaluated the situation and
opened the path through Bridge B.
How STP Works
When enabled, STP determines the most appropriate path for traffic through a network. The way it does this is
outlined in the sections below.
STP Requirements
Before STP can configure the network, the system must satisfy the following requirements:

Communication between all the bridges. This communication is carried out using Bridge Protocol Data Units

Each bridge must have a Bridge Identifier that specifies which bridge acts as the central reference point, or
(BPDUs), which are transmitted in packets with a known multicast address.
Root Bridge, for the STP system—bridges with a lower Bridge Identifier are more likely to be designated as
the Root Bridge. The Bridge Identifier is calculated using the MAC address of the bridge and a priority
defined for the bridge. The default priority of the NPort S8000 is 32768.

Each port has a cost that specifies the efficiency of each link. The efficiency cost is usually determined by
the bandwidth of the link, with less efficient links assigned a higher cost. The following table shows the
default port costs for a switch:
Port Speed
Path Cost 802.1D,
Path Cost
1998 Edition
802.1w-2001
10 Mbps
100
2,000,000
100 Mbps
19
200,000
1000 Mbps
4
20,000
STP Calculation
The first step of the STP process is to perform calculations. During this stage, each bridge on the network
transmits BPDUs. The following items will be calculated:
•
Which bridge should be the Root Bridge. The Root Bridge is the central reference point from which the
network is configured.
•
The Root Path Costs for each bridge. This is the cost of the paths from each bridge to the Root Bridge.
•
The identity of each bridge’s Root Port. The Root Port is the port on the bridge that connects to the Root
Bridge via the most efficient path. In other words, the port connected to the Root Bridge via the path with
the lowest Root Path Cost. The Root Bridge, however, does not have a Root Port.
•
The identity of the Designated Bridge for each LAN segment. The Designated Bridge is the bridge with the
lowest Root Path Cost from that segment. If several bridges have the same Root Path Cost, the one with the
lowest Bridge Identifier becomes the Designated Bridge. Traffic transmitted in the direction of the Root
Bridge will flow through the Designated Bridge. The port on this bridge that connects to the segment is
called the Designated Bridge Port.
STP Configuration
After all the bridges on the network agree on the identity of the Root Bridge, and all other relevant parameters
have been established, each bridge is configured to forward traffic only between its Root Port and the
Designated Bridge Ports for the respective network segments. All other ports are blocked, which means that
they will not be allowed to receive or forward traffic.
6-16
NPort S8000 Series
Switch Featured Functions
STP Reconfiguration
Once the network topology has stabilized, each bridge listens for Hello BPDUs transmitted from the Root Bridge
at regular intervals. If a bridge does not receive a Hello BPDU after a certain interval (the Max Age time), the
bridge assumes that the Root Bridge, or a link between itself and the Root Bridge, has gone down. This will
trigger the bridge to reconfigure the network to account for the change. If you have configured an SNMP trap
destination, when the topology of your network changes, the first bridge to detect the change sends out an
SNMP trap.
Differences between RSTP and STP
RSTP is similar to STP, but includes additional information in the BPDUs that allow each bridge to confirm that
it has taken action to prevent loops from forming when it decides to enable a link to a neighboring bridge.
Adjacent bridges connected via point-to-point links will be able to enable a link without waiting to ensure that
all other bridges in the network have had time to react to the change. The main benefit of RSTP is that the
configuration decision is made locally rather than network-wide, allowing RSTP to carry out automatic
configuration and restore a link faster than STP.
STP Example
The LAN shown in the following figure has three segments, with adjacent segments connected using two
possible links. The various STP factors, such as Cost, Root Port, Designated Bridge Port, and Blocked Port are
shown in the figure.
•
Bridge A has been selected as the Root Bridge, since it was determined to have the lowest Bridge Identifier
on the network.
•
Since Bridge A is the Root Bridge, it is also the Designated Bridge for LAN segment 1. Port 1 on Bridge A is
selected as the Designated Bridge Port for LAN Segment 1.
•
Ports 1 of Bridges B, C, X, and Y are all Root Ports sine they are nearest to the Root Bridge, and therefore
have the most efficient path.
•
Bridges B and X offer the same Root Path Cost for LAN segment 2. However, Bridge B was selected as the
Designated Bridge for that segment since it has a lower Bridge Identifier. Port 2 on Bridge B is selected as
the Designated Bridge Port for LAN Segment 2.
•
Bridge C is the Designated Bridge for LAN segment 3, because it has the lowest Root Path Cost for LAN
Segment 3:
 The route through Bridges C and B costs 200 (C to B=100, B to A=100)
 he route through Bridges Y and B costs 300 (Y to B=200, B to A=100)Item 3.3
•
The Designated Bridge Port for LAN Segment 3 is Port 2 on Bridge C.
Using STP on a Network with Multiple VLANs
IEEE Std 802.1D, 1998 Edition, does not take into account VLANs when calculating STP information—the
calculations only depend on the physical connections. Consequently, some network configurations will result in
VLANs being subdivided into a number of isolated sections by the STP system. You must ensure that every
VLAN configuration on your network takes into account the expected STP topology and alternative topologies
that may result from link failures.
The following figure shows an example of a network that contains VLANs 1 and 2. The VLANs are connected
using the 802.1Q-tagged link between Switch B and Switch C. By default, this link has a port cost of 100 and
is automatically blocked because the other Switch-to-Switch connections have a port cost of 36 (18+18). This
means that both VLANs are now subdivided—VLAN 1 on Switch units A and B cannot communicate with VLAN
1 on Switch C, and VLAN 2 on Switch units A and C cannot communicate with VLAN 2 on Switch B.
6-17
NPort S8000 Series
Switch Featured Functions
To avoid subdividing VLANs, all inter-switch connections should be made members of all available 802.1Q
VLANs. This will ensure connectivity at all times. For example, the connections between Switches A and B, and
between Switches A and C should be 802.1Q tagged and carrying VLANs 1 and 2 to ensure connectivity.
See the “Configuring Virtual LANs” section for more information about VLAN Tagging.
Configuring STP/RSTP
The following figures indicate which Spanning Tree Protocol parameters can be configured. A more detailed
explanation of each parameter follows.
Redundancy Protocol
Setting
Description
Factory Default
Turbo Ring
Select this item to change to the Turbo Ring configuration page.
Turbo Ring 2
Select this item to change to the Turbo Ring 2 nfiguration page.
RSTP (IEEE
Select this item to change to the RSTP configuration page.
default
802.1W/1D)
Bridge priority
Setting
Description
Factory Default
Numerical value
Increase this device’s bridge priority by selecting a lower
32768
selected by user
number. A device with a higher bridge priority has a greater
chance of being established as the root of the Spanning Tree
6-18
NPort S8000 Series
Switch Featured Functions
topology.
Hello time (sec.)
Setting
Description
Factory Default
Numerical value input
The root of the Spanning Tree topology periodically sends out a 2
“hello” message to other devices on the network to check if the
by user
topology is healthy. The “hello time” is the amount of time the
root waits between sending hello messages.
Forwarding Delay
Setting
Description
Factory Default
Numerical value input
The amount of time this device waits before checking to see if it 15 (sec.)
by user
should change to a different state.
Max. Age (sec.)
Setting
Description
Factory Default
Numerical value input
If this device is not the root, and it has not received a hello
20
by user
message from the root in an amount of time equal to “Max.
Age,” then this device will reconfigure itself as a root. Once two
or more devices on the network are recognized as a root, the
devices will renegotiate to set up a new Spanning Tree
topology.
Enable RSTP per Port
Setting
Description
Factory Default
Enable/Disable
Select to enable the port as a node on the Spanning Tree
Disabled
topology.
NOTE
We suggest not enabling the Spanning Tree Protocol once the port is connected to a device (PLC, RTU, etc.) as
opposed to network equipment. The reason is that it will cause unnecessary negotiation.
Port Priority
Setting
Description
Factory Default
Numerical value
Increase this port’s priority as a node on the Spanning Tree
128
selected by user
topology by entering a lower number.
Port Cost
Setting
Description
Factory Default
Numerical value input
Input a higher cost to indicate that this port is less suitable as a 200000
by user
node for the Spanning Tree topology.
Configuration Limits of STP/RSTP
The Spanning Tree Algorithm places limits on three of the configuration items described previously:
[Eq. 1]:
1 sec ≦ Hello Time ≦ 10 sec
[Eq. 2]:
6 sec ≦ Max. Age ≦ 40 sec
[Eq. 3]:
4 sec ≦ Forwarding Delay ≦ 30 sec
These three variables are further restricted by the following two inequalities:
[Eq. 4]:
2 * (Hello Time + 1 sec) ≦ Max. Age ≦ 2 * (Forwarding Delay – 1 sec)
The NPort S8000’s firmware will alert you immediately if any of these restrictions are violated. For example,
setting
6-19
NPort S8000 Series
Switch Featured Functions
Hello Time = 5 sec, Max. Age = 20 sec, and Forwarding Delay = 4 sec does not violate Eqs. 1 through 3, but
does violate Eq. 4, since in this case,
2 * (Hello Time + 1 sec) = 12 sec, and 2 * (Forwarding Delay – 1 sec) = 6 sec.
You can remedy the situation in many ways. One solution is simply to increase the Forwarding Delay value to
at least 11 sec.
HINT: Perform the following steps to avoid guessing:
Step 1: Assign a value to “Hello Time” and then calculate the left most part of Eq. 4 to get the lower limit of
“Max. Age”.
Step 2: Assign a value to “Forwarding Delay” and then calculate the right most part of Eq. 4 to get the upper
limit for “Max. Age”.
Step 3: Assign a value to “Forwarding Delay” that satisfies the conditions in Eq. 3 and Eq. 4.
Bandwidth Management
Using Bandwidth Management
In general, one host should not be allowed to occupy unlimited bandwidth, particularly when the device
malfunctions. For example, so-called “broadcast storms” could be caused by an incorrectly configured topology,
or a malfunctioning device. The NPort S8000 not only prevents broadcast storms, but can also be configured to
a different ingress rate for all packets, giving administrators full control of their limited bandwidth to prevent
undesirable effects caused by unpredictable faults.
Configuring Bandwidth Management
Traffic Rate Limiting Settings
Ingress
Setting
Description
Factory Default
Ingress rate
Select the ingress rate for all packets from the following
N/A
options: not limited, 128K, 256K, 512K, 1M, 2M, 4M, 8M
6-20
NPort S8000 Series
Switch Featured Functions
Line Swap Fast Recovery
Using Line-Swap-Fast-Recovery
The Line-Swap Fast Recovery function, which is enabled by default, allows the NPort S8000 to return to normal
operation extremely quickly after devices are unplugged and then re-plugged into different ports. The recovery
time is on the order of a few milliseconds (compare this with standard commercial switches for which the
recovery time could be on the order of several minutes). To disable the Line-Swap Fast Recovery function, or
to re-enable the function after it has already been disabled, access either the Console utility’s Line-Swap
recovery page, or the Web Browser interface’s Line-Swap fast recovery page, as the following figure
shows:
Configuring Line-Swap Fast Recovery
Enable Line-Swap-Fast-Recovery
Setting
Description
Factory Default
Enable/Disable
Select this option to enable the Line-Swap-Fast-Recovery
Enable
function
Ethernet Advanced Settings
Ethernet Traffic Prioritization
Using Traffic Prioritization
The NPort S8000’s traffic prioritization capability provides Quality of Service (QoS) to your network by making
data delivery more reliable. You can prioritize traffic on your network to ensure that high priority data is
transmitted with minimum delay. Traffic can be controlled by a set of rules to obtain the required Quality of
Service for your network. The rules define different types of traffic and specify how each type should be treated
as it passes through the switch. The NPort S8000 can inspect both IEEE 802.1p/1Q layer 2 CoS tags, and even
layer 3 TOS information to provide consistent classification of the entire network. The NPort S8000’s QoS
capability improves the performance and determinism of industrial networks for mission critical applications.
6-21
NPort S8000 Series
Switch Featured Functions
The Traffic Prioritization Concept
What is Traffic Prioritization?
Traffic prioritization allows you to prioritize data so that time-sensitive and system-critical data can be
transferred smoothly and with minimal delay over a network. The benefits of using traffic prioritization are:
•
•
Improve network performance by controlling a wide variety of traffic and managing congestion.
Assign priorities to different categories of traffic. For example, set higher priorities for time-critical or
business-critical applications.
•
Provide predictable throughput for multimedia applications, such as video conferencing or voice over IP,
and minimize traffic delay and jitter.
•
Improve network performance as the amount of traffic grows. This will save cost by reducing the need to
keep adding bandwidth to the network.
How Traffic Prioritization Works
Traffic prioritization uses the four traffic queues that are present in your NPort S8000 to ensure that high
priority traffic is forwarded on a different queue from lower priority traffic. This is what provides Quality of
Service (QoS) to your network.
NPort S8000 traffic prioritization depends on two industry-standard methods:
•
IEEE 802.1D—a layer 2 marking scheme.
•
Differentiated Services (DiffServ)—a layer 3 marking scheme.
IEEE 802.1D Traffic Marking
The IEEE Std 802.1D, 1998 Edition marking scheme, which is an enhancement to IEEE Std 802.1D, enables
Quality of Service on the LAN. Traffic service levels are defined in the IEEE 802.1Q 4-byte tag, which is used to
carry VLAN identification as well as IEEE 802.1p priority information. The 4-byte tag immediately follows the
destination MAC address and Source MAC address.
The IEEE Std 802.1D, 1998 Edition priority marking scheme assigns an IEEE 802.1p priority level between 0
and 7 to each frame. This determines the level of service that that type of traffic should receive. Refer to the
table below for an example of how different traffic types can be mapped to the eight IEEE 802.1p priority levels.
IEEE 802.1p Priority Level
IEEE 802.1D Traffic Type
0
Best Effort (default)
1
Background
2
Standard (spare)
3
Excellent Effort (business critical)
4
Controlled Load (streaming multimedia)
5
Video (interactive media); less than 100 milliseconds of latency and jitter
6
Voice (interactive voice); less than 10 milliseconds of latency and jitter
7
Network Control Reserved traffic
Even though the IEEE 802.1D standard is the most widely used prioritization scheme in the LAN environment,
it still has some restrictions:
•
It requires an additional 4-byte tag in the frame, which is normally optional in Ethernet networks. Without
this tag, the scheme cannot work.
•
The tag is part of the IEEE 802.1Q header, so to implement QoS at layer 2, the entire network must
implement IEEE 802.1Q VLAN tagging.
It is only supported on a LAN and not routed across WAN links, since the IEEE 802.1Q tags are removed when
the packets pass through a router.
6-22
NPort S8000 Series
Switch Featured Functions
Differentiated Services (DiffServ) Traffic Marking
DiffServ is a Layer 3 marking scheme that uses the DiffServ Code Point (DSCP) field in the IP header to store
the packet priority information. DSCP is an advanced intelligent method of traffic marking as you can choose
how your network prioritizes different types of traffic. DSCP uses 64 values that map to user-defined service
levels, allowing you to establish more control over network traffic.
Advantages of DiffServ over IEEE 802.1D are:
•
Configure how you want your switch to treat selected applications and types of traffic by assigning various
grades of network service to them.
•
No extra tags are required in the packet.
•
DSCP uses the IP header of a packet and therefore priority is preserved across the Internet.
•
DSCP is backward compatible with IPV4 TOS, which allows operation with existing devices that use a layer
3 TOS enabled prioritization scheme.
Traffic Prioritization
The NPort S8000 classifies traffic based on layer 2 of the OSI 7 layer model, and the switch prioritizes received
traffic according to the priority information defined in the received packet. Incoming traffic is classified based
upon the IEEE 802.1D frame and is assigned to the appropriate priority queue based on the IEEE 802.1p service
level value defined in that packet. Service level markings (values) are defined in the IEEE 802.1Q 4-byte tag,
and consequently traffic will only contain 802.1p priority markings if the network is configured with VLANs and
VLAN tagging. The traffic flow through the switch is as follows:
1. A packet received by the NPort S8000 may or may not have an 802.1p tag associated with it. If it does not,
then it is given a default 802.1p tag (which is usually 0). Alternatively, the packet may be marked with a
new 802.1p value, which will result in all knowledge of the old 802.1p tag being lost.
2. As the 802.1p priority levels are fixed to the traffic queues, the packet will be placed in the appropriate
priority queue, ready for transmission through the appropriate egress port. When the packet reaches the
head of its queue and is about to be transmitted, the device determines whether or not the egress port is
tagged for that VLAN. If it is, then the new 802.1p tag is used in the extended 802.1D header.
The NPort S8000 will check a packet received at the ingress port for IEEE 802.1D traffic classification, and then
prioritize it based upon the IEEE 802.1p value (service levels) in that tag. It is this 802.1p value that
determines to which traffic queue the packet is mapped.
Traffic Queues
The NPort S8000 hardware has multiple traffic queues that allow packet prioritization to occur. Higher priority
traffic can pass through the NPort S8000 without being delayed by lower priority traffic. As each packet arrives
in the NPort S8000, it passes through any ingress processing (which includes classification,
marking/re-marking), and is then sorted into the appropriate queue. The switch then forwards packets from
each queue.
The NPort S8000 supports two different queuing mechanisms:
•
Weight Fair: This method services all the traffic queues, giving priority to the higher priority queues.
Under most circumstances, this method gives high priority precedence over low-priority, but in the event
that high-priority traffic exceeds the link capacity, lower priority traffic is not blocked.
•
Strict: This method services high traffic queues first; low priority queues are delayed until no more high
priority data needs to be sent. This method always gives precedence to high priority over low-priority.
Configuring Ethernet Traffic Prioritization
Quality of Service (QoS) provides a traffic prioritization capability to ensure that important data is delivered
consistently and predictably. The NPort S8000 can inspect IEEE 802.1p/1Q layer 2 CoS tags, and even layer 3
TOS information, to provide a consistent classification of the entire network. The NPort S8000’s QoS capability
improves your industrial network’s performance and determinism for mission critical applications.
6-23
NPort S8000 Series
Switch Featured Functions
QoS Classification
The NPort S8000 supports inspection of layer 3 TOS and/or layer 2 CoS tag information to determine how to
classify traffic packets.
Queuing Mechanism
Setting
Weighted Fair
Description
Factory Default
The NPort S8000 has 4 priority queues. In the weighted fair
Weight Fair
scheme, an 8, 4, 2, 1 weighting is applied to the four priorities.
This approach prevents the lower priority frames from being
starved of opportunity for transmission with only a slight delay
to the higher priority frames.
Strict
In the Strict-priority scheme, all top-priority frames egress a
port until that priority’s queue is empty, and then the next
lower priority queue’s frames egress. This approach can cause
the lower priorities to be starved of opportunity for transmitting
any frames but ensures all high priority frames to egress the
switch as soon as possible.
Inspect TOS
Setting
Description
Enable/Disable
Select the option to enable the NPort S8000 to inspect the Type Enable
Factory Default
of Service (TOS) bits in IPV4 frame to determine the priority of
each frame.
Inspect COS
Setting
Description
Factory Default
Enable/Disable
Select the option to enable the NPort S8000 to inspect the
Enable
802.1p COS tag in the MAC frame to determine the priority of
each frame.
Port Priority
Setting
Description
Factory Default
Numerical value
Increase this port’s priority as a node on the 802.1d priority
3
selected by user ( from queue. The higher number the higher priority.
0
to 7)
6-24
NPort S8000 Series
NOTE
NOTE
Switch Featured Functions
The priority of an ingress frame is determined in order by:
1.
Inspect TOS
2.
Inspect CoS
3.
Port Highest Priority
The designer can enable these classifications individually or in combination. For instance, if a ‘hot,’ higher
priority port is required for a network design, “Inspect TOS” and “Inspect CoS” can be disabled. This setting
leaves only port default priority active, which results in all ingress frames being assigned the same priority on
that port.
CoS Mapping
Setting
Description
Factory
Low
Set the mapping table of different CoS values to 4 different
0: Low
Normal
egress queues.
1: Low
Medium
2: Normal
High
3: Normal
4: Medium
5: Medium
6: High
7: High
6-25
NPort S8000 Series
Switch Featured Functions
ToS/DiffServ Mapping
Setting
Description
Factory Default
Low
Set the mapping table of different TOS values to 4 different
1 to 16: Low
Normal
egress queues.
17 to 32: Normal
Medium
33 to 48: Medium
High
49 to 64: High
Virtual LAN
Using Virtual LAN
Setting up Virtual LANs (VLANs) on your NPort S8000 increases the efficiency of your network by dividing the
LAN into logical segments, as opposed to physical segments. In general, VLANs are easier to manage.
The Virtual LAN (VLAN) Concept
What is a VLAN?
A VLAN is a group of devices that can be located anywhere on a network, but which communicate as if they are
on the same physical segment. With VLANs, you can segment your network without being restricted by physical
connections—a limitation of traditional network design. As an example, with VLANs you can segment your
network according to:
•
Departmental groups—You could have one VLAN for the Marketing department, another for the Finance
•
Hierarchical groups—You could have one VLAN for directors, another for managers, and another for
department, and another for the Development department.
general staff.
•
Usage groups—You could have one VLAN for e-mail users, and another for multimedia users.
6-26
NPort S8000 Series
Switch Featured Functions
Switch A
1
2\
3
2
4\
5
2
6\
7
2
Backbone connects multiple switches
1
2\
3
2
Department 1
Department 2
VLAN 1
VLAN 2
4\
2
5
Switch B
6\ 7
8\
2
2
Department 3
VLAN 3
Benefits of VLANs
The main benefit of VLANs is that they provide a network segmentation system that is far more flexible than
traditional networks. Using VLANs also provides you with three other benefits:
•
VLANs ease the relocation of devices on networks: With traditional networks, network administrators
spend most of their time dealing with moves and changes. If users move to a different subnetwork, the
addresses of each host must be updated manually. With a VLAN setup, if a host on VLAN Marketing, for
example, is moved to a port in another part of the network, and retains its original subnet membership, you
only need to specify that the new port is on VLAN Marketing. You do not need to carry out any re-cabling.
•
VLANs provide extra security: Devices within each VLAN can only communicate with other devices on
the same VLAN. If a device on VLAN Marketing needs to communicate with devices on VLAN Finance, the
traffic must pass through a routing device or Layer 3 switch.
•
VLANs help control traffic: With traditional networks, congestion can be caused by broadcast traffic that
is directed to all network devices, regardless of whether or not they need it. VLANs increase the efficiency
of your network because each VLAN can be set up to contain only those devices that need to communicate
with each other.
VLANs and Moxa EtherDevice Switch
Your NPort S8000 provides support for VLANs using IEEE Std 802.1Q-1998. This standard allows traffic from
multiple VLANs to be carried across one physical link. The IEEE Std 802.1Q-1998 standard allows each port on
your NPort S8000 to be placed in:
•
Any one VLAN defined on the NPort S8000.
•
Several VLANs at the same time using 802.1Q tagging.
The standard requires that you define the 802.1Q VLAN ID for each VLAN on your NPort S8000 before the
switch can use it to forward traffic:
Managing a VLAN
A new or initialized NPort S8000 contains a single VLAN—the Default VLAN. This VLAN has the following
definition:
•
VLAN Name—Management VLAN
•
802.1Q VLAN ID—1 (if tagging is required)
All the ports are initially placed on this VLAN, and it is the only VLAN that allows you to access the management
software of the NPort S8000 over the network.
6-27
NPort S8000 Series
Switch Featured Functions
Communication Between VLANs
If devices connected to a VLAN need to communicate to devices on a different VLAN, a router or Layer 3
switching device with connections to both VLANs needs to be installed. Communication between VLANs can
only take place if they are all connected to a routing or Layer 3 switching device.
VLANs: Tagged and Untagged Membership
The NPort S8000 supports 802.1Q VLAN tagging, a system that allows traffic for multiple VLANs to be carried
on a single physical (backbone, trunk) link. When setting up VLANs you need to understand when to use
untagged and tagged membership of VLANs. Simply put, if a port is on a single VLAN it can be an untagged
member, but if the port needs to be a member of multiple VLANs, tagged membership must be defined.
A typical host (e.g., clients) will be untagged members of one VLAN, defined as “Access Port” in the NPort
S8000, while inter-switch connections will be tagged members of all VLANs, defined as “Trunk Port” in the
NPort S8000.
The IEEE Std 802.1Q-1998 defines how VLANs operate within an open packet-switched network. An 802.1Q
compliant packet carries additional information that allows a switch to determine which VLAN the port belongs.
If a frame is carrying the additional information, it is known as a tagged frame.
To carry multiple VLANs across a single physical (backbone, trunk) link, each packet must be tagged with a
VLAN identifier so that the switches can identify which packets belong to which VLAN. To communicate between
VLANs, a router must be used.
The NPort S8000 supports two types of VLAN port settings:
•
Access Port: The port connects to a single device that is not tagged. The user must define the default port
PVID that determines to which VLAN the device belongs. Once the ingress packet of this Access Port
egresses to another Trunk Port (the port needs all packets to carry tag information), the NPort S8000 will
insert this PVID into this packet to help the next 802.1Q VLAN switch recognize it.
•
Trunk Port: The port connects to a LAN that consists of untagged devices/tagged devices and/or switches
and hubs. In general, the traffic of the Trunk Port must have a Tag. Users can also assign PVID to a Trunk
Port. The untagged packet on the Trunk Port will be assigned the port default PVID as its VID.
The following section illustrates how to use these ports to set up different applications.
6-28
NPort S8000 Series
Switch Featured Functions
Sample Applications of VLANs using the NPort S8000
In this application:
•
Port 1 connects a single untagged device and assigns it to VLAN 5; it should be configured as “Access Port”
with PVID 5.
•
Port 2 connects a LAN with two untagged devices belonging to VLAN 2. One tagged device with VID 3 and
one tagged device with VID 4. It should be configured as “Trunk Port” with PVID 2 for untagged device and
Fixed VLAN (Tagged) with 3 and 4 for tagged device. Since each port can only have one unique PVID, all
untagged devices on the same port can only belong to the same VLAN.
•
Port 3 connects with another switch. It should be configured as “Trunk Port.” GVRP protocol will be used
through the Trunk Port.
•
Port 4 connects a single untagged device and assigns it to VLAN 2; it should be configured as “Access Port”
with PVID 2.
•
Port 5 connects a single untagged device and assigns it to VLAN 3; it should be configured as “Access Port”
with PVID 3.
•
Port 6 connect a single untagged device and assigns it to VLAN 5; it should be configured as “Access Port”
with PVID 5.
•
Port 7 connects a single untagged device and assigns it to VLAN 4; it should be configured as “Access Port”
with PVID 4.
After proper configuration:
•
Packets from device A will travel through “Trunk Port 3” with tagged VID 5. Switch B will recognize its VLAN,
pass it to port 6, and then remove tags received successfully by device G, and vice versa.
•
Packets from device B and C will travel through “Trunk Port 3” with tagged VID 2. Switch B recognizes its
VLAN, passes it to port 4, and then removes tags received successfully by device F, and vice versa.
•
Packets from device D will travel through “Trunk Port 3” with tagged VID 3. Switch B will recognize its VLAN,
pass to port 5, and then remove tags received successfully by device H. Packets from device H will travel
through “Trunk Port 3” with PVID 3. Switch A will recognize its VLAN and pass it to port 2, but will not
remove tags received successfully by device D.
•
Packets from device E will travel through “Trunk Port 3” with tagged VID 4. Switch B will recognize its VLAN,
pass it to port 7, and then remove tags received successfully by device I. Packets from device I will travel
through “Trunk Port 3” with tagged VID 4. Switch A will recognize its VLAN and pass it to port 2, but will not
remove tags received successfully by device E.
6-29
NPort S8000 Series
Switch Featured Functions
Configuring Virtual LAN
VLAN Settings 802.1Q VLAN
To configure the NPort S8000’s 802.1Q VLAN, use the VLAN Setting page to configure the ports.
VLAN Mode
Setting
Description
Factory Default
802.1Q VLAN
Set VLAN mode to 802.1Q VLAN
802.1Q VLAN
Port-based VLAN
Set VLAN mode to Port-based VLAN
Management VLAN ID
Setting
Description
Factory Default
VLAN ID ranges from 1 Set the management VLAN of this NPort S8000.
1
to 4094
Port Type
Setting
Description
Factory Default
Access
This port type is used to connect single devices without tags.
Access
Trunk
Select “Trunk” port type to connect another 802.1Q VLAN
aware switch or another LAN that combines tagged and/or
untagged devices and/or other switches/hubs.
ATTENTION
For communication redundancy in the VLAN environment, set “Redundant Port,” “Coupling Port,” and
“Coupling Control Port” as “Trunk Port,” since these ports act as the “backbone” to transmit all packets of
different VLANs to different NPort S8000 units.
Port PVID
Setting
Description
Factory Default
VID range from 1 to
Set the port default VLAN ID for untagged devices that connect 1
4094
to the port.
Fixed VLAN List (Tagged)
Setting
Description
Factory Default
VID range from 1 to
This field will be active only when selecting the “Trunk” port
None
4094
type. Set the other VLAN ID for tagged devices that connect to
the “Trunk” port. Use commas to separate different VIDs.
6-30
NPort S8000 Series
Switch Featured Functions
Forbidden VLAN List
Setting
Description
Factory Default
VID range from 1 to
This field will be active only when selecting the “Trunk” port
None
4094
type. Set the VLAN IDs that will not be supported by this trunk
port. Use commas to separate different VIDs.
Port-based VLAN
To configure the NPort S8000’s Port-based VLAN, use the VLAN Setting page to configure the ports.
VLAN Mode
Setting
Description
Factory Default
802.1Q VLAN
Set VLAN mode to 802.1Q VLAN
802.1Q VLAN
Port-based VLAN
Set VLAN mode to Port-based VLAN
Port
Setting
Description
Factory Default
Enable/Disable
Set port to specific VLAN Group.
Enable
(all ports belong to
VLAN1)
In 802.1Q VLAN table, you can review the VLAN groups that were created, Joined Access Ports, and Trunk Ports,
and in Port-based VLAN table, you can review the VLAN group and Joined port.
NOTE
The physical network can have a maximum of 64 VLAN settings.
Multicast Filtering
Using Multicast Filtering
Multicast filtering improves the performance of networks that carry multicast traffic. This section explains
multicasts, multicast filtering, and how multicast filtering can be implemented on your NPort S8000.
The Concept of Multicast Filtering
What is an IP Multicast?
A multicast is a packet sent by one host to multiple hosts. Only those hosts that belong to a specific multicast
group will receive the multicast. If the network is set up correctly, a multicast can only be sent to an end-station
6-31
NPort S8000 Series
Switch Featured Functions
or a subset of end-stations on a LAN or VLAN that belong to the multicast group. Multicast group members can
be distributed across multiple subnets, so that multicast transmissions can occur within a campus LAN or over
a WAN. In addition, networks that support IP multicast send only one copy of the desired information across the
network until the delivery path that reaches group members diverges. To make more efficient use of network
bandwidth, it is only at these points that multicast packets are duplicated and forwarded. A multicast packet
has a multicast group address in the destination address field of the packet’s IP header.
Benefits of Multicast
The benefits of using IP multicast are that it:
•
Uses the most efficient, sensible method to deliver the same information to many receivers with only one
transmission.
•
Reduces the load on the source (for example, a server) since it will not need to produce several copies of the
same data.
•
Makes efficient use of network bandwidth and scales well as the number of multicast group members
increases.
•
Works with other IP protocols and services, such as Quality of Service (QoS).
Multicast transmission makes more sense and is more efficient than unicast transmission for some applications.
For example, multicasts are often used for video-conferencing, since high volumes of traffic must be sent to
several end-stations at the same time, but where broadcasting the traffic to all end-stations would cause a
substantial reduction in network performance. Furthermore, several industrial automation protocols, such as
Allen-Bradley, EtherNet/IP, Siemens Profibus, and Foundation Fieldbus HSE (High Speed Ethernet), use
multicast. These industrial Ethernet protocols use publisher/subscriber communications models by
multicasting packets that could flood a network with heavy traffic. IGMP Snooping is used to prune multicast
traffic so that it travels only to those end destinations that require the traffic, reducing the amount of traffic on
the Ethernet LAN.
Multicast Filtering
Multicast filtering ensures that only end-stations that have joined certain groups receive multicast traffic. With
multicast filtering, network devices only forward multicast traffic to the ports that are connected to registered
end-stations. The following two figures illustrate how a network behaves without multicast filtering, and with
multicast filtering.
Network without multicast filtering
All hosts receive the multicast traffic, even if they don’t need it.
6-32
NPort S8000 Series
Switch Featured Functions
Network with multicast filtering
Hosts only receive dedicated traffic from other hosts belonging to the same group
Multicast Filtering and Moxa Switching Device Server
The NPort S8000 has three ways to achieve multicast filtering: IGMP (Internet Group Management Protocol)
Snooping, GMRP (GARP Multicast Registration Protocol), and adding a static multicast MAC manually to filter
multicast traffic automatically
IGMP Multicast Filtering
IGMP is used by IP-supporting network devices to register hosts with multicast groups. It can be used on all
LANs and VLANs that contain a multicast capable IP router, and on other network devices that support
multicast filtering. IGMP works as follows:
The IP router (or querier) periodically sends query packets to all end-stations on the LANs or VLANs that are
connected to it. For networks with more than one IP router, the router with the lowest IP address is the querier.
A switch with IP address lower than the IP address of any other IGMP queriers connected to the LAN or VLAN
can become the IGMP querier.
When an IP host receives a query packet, it sends a report packet back that identifies the multicast group that
the end-station would like to join.
When the report packet arrives at a port on a switch with IGMP Snooping enabled, the switch knows that the
port should forward traffic for the multicast group, and then proceeds to forward the packet to the router.
When the router receives the report packet, it registers that the LAN or VLAN requires traffic for the multicast
groups.
When the router forwards traffic for the multicast group to the LAN or VLAN, the switches only forward the
traffic to ports that received a report packet.
6-33
NPort S8000 Series
Switch Featured Functions
IGMP (Internet Group Management Protocol)
Snooping Mode
Snooping Mode allows your switch to forward multicast packets only to the appropriate ports. The switch
“snoops” on exchanges between hosts and an IGMP device, such as a router, to find those ports that want to
join a multicast group, and then configures its filters accordingly.
Query Mode
Query mode allows the NPort S8000 to work as the Querier if it has the lowest IP address on the subnetwork
to which it belongs. IGMP querying is enabled by default on the NPort S8000 to help prevent interoperability
issues with some multicast routers that may not follow the lowest IP address election method. Enable query
mode to run multicast sessions on a network that does not contain IGMP routers (or queriers).
NOTE
The NPort S8000 is compatible with any device that conforms to the IGMP v2 and IGMP v3 device protocol.
Configuring IGMP Snooping
IGMP Snooping provides the ability to prune multicast traffic so that it travels only to those end destinations
that require that traffic, thereby reducing the amount of traffic on the Ethernet LAN.
IGMP Snooping Settings
IGMP Snooping Enable
Setting
Description
Factory Default
Enable/Disable
Select the option to enable the IGMP Snooping function
Disabled
globally.
Query Interval
Setting
Description
Factory Default
Numerical value input
Set the query interval of the Querier function globally. Valid
125 seconds
by user
settings are from 20 to 600 seconds.
IGMP Snooping
Setting
Description
Factory Default
Enable/Disable
Select the option to enable the IGMP Snooping function per
Enabled if IGMP
VLAN.
Snooping Enabled
Globally
Querier
Setting
Description
Enable/Disable
Select the option to enable the NPort S8000’s querier function. Enabled if IGMP
Factory Default
6-34
NPort S8000 Series
Switch Featured Functions
Snooping is Enabled
Globally
Static Multicast Router Port
Setting
Description
Factory Default
Select/Deselect
Select the option to select which ports will connect to the
Disabled
multicast routers. It’s active only when IGMP Snooping is
enabled.
NOTE
At least one switch must be designated the Querier or enable IGMP snooping and GMRP when enabling Turbo
Ring and IGMP snooping simultaneously.
Static Multicast MAC
Some devices may only support multicast packets, but not support either IGMP Snooping or GMRP. The NPort
S8000 supports adding multicast groups manually to enable multicast filtering.
Add New Static Multicast Address to the List
Setting
Description
Factory Default
MAC Address
Input the multicast MAC address of this host.
None
Description
Factory Default
Select the appropriate options to select the join ports for this
None
Join Port
Setting
Select/Deselect
multicast group.
GMRP (GARP Multicast Registration Protocol)
The NPort S8000 supports IEEE 802.1D-1998 GMRP (GARP Multicast Registration Protocol), which differs from
IGMP (Internet Group Management Protocol). GMRP is a MAC-based multicast management protocol, whereas
IGMP is IP-based. GMRP provides a mechanism that allows bridges and end stations to register or de-register
Group membership information dynamically. GMRP functions similarly to GVRP, except that GMRP registers
multicast addresses on ports. When a port receives a GMRP-join message, it will register the multicast
address to its database if the multicast address is not registered, and all the multicast packets with that
multicast address are able to be forwarded from this port. When a port receives a GMRP-leave message, it will
de-register the multicast address from its database, and all the multicast packets with this multicast address
are not able to be forwarded from this port.
6-35
NPort S8000 Series
Switch Featured Functions
(Please refer to Chapter 6, System Monitoring / Ethernet Status for IGMP/GMRP Table)
Configuring GMRP
GMRP is a MAC-based multicast management protocol, whereas IGMP is IP-based. GMRP provides a
mechanism that allows bridges and end stations to register or un-register Group membership information
dynamically.
GMRP enable
Setting
Description
Factory Default
Enable/Disable
Select the option to enable the GMRP function for the port listed Disable
in the Port column
Set Device IP
Using Set Device IP
To reduce the effort required to set up IP addresses, the NPort S8000 comes equipped with DHCP/BOOTP
server and RARP protocol to set up IP addresses of Ethernet-enabled devices automatically.
When enabled, the Set device IP function allows The NPort S8000 to assign specific IP addresses
automatically to connected devices that are equIPped with DHCP Client or RARP protocol. In effect, the NPort
S8000 acts as a DHCP server by assigning a connected device with a specific IP address stored in its internal
memory. Each time the connected device is switched on or rebooted, the NPort S8000 sends the device the
desired IP address.
Perform the following steps to use the Set device IP function:
6-36
NPort S8000 Series
1.
Switch Featured Functions
set up the connected devices
Set up those Ethernet-enabled devices connected to the NPort
S8000 for which you would like IP addresses to be assigned
automatically. The devices must be configured to obtain their IP
address automatically.
The devices’ configuration utility should include a setup page
that allows you to choose an option similar to Obtain an IP
address automatically.
For example, Windows’ TCP/IP Properties window is shown at
the right. Although your device’s configuration utility may look
quite a bit different, this figure should give you some idea of
what to look for.
You also need to decide to which of the NPort S8000’s ports your
Ethernet-enabled devices will be connected. You will need to set
up each of these ports separately, as described in the following
step.
2. Configure the NPort S8000’s Set device IP function, either from the Console utility or from the Web Browser
interface. In either case, you simply need to enter the Desired IP for each port that needs to be configured.
3. Be sure to activate your settings before exiting.
•
•
When using the Web Browser interface, activate by clicking Activate.
When using the Console utility, activate by first highlighting the Activate menu option, and then press
Enter. You should receive the Set device IP settings are now active! (Press any key to continue)
message.
Configuring Set Device IP
Desired IP Address
Setting
Description
Factory Default
IP Address
Set the desired IP of connected devices.
None
The DHCP Relay Agent makes it possible for DHCP broadcast messages to be sent over routers. The DHCP Relay
Agent enables DHCP clients to obtain IP addresses from a DHCP server on a remote subnet, or those that are
not located on the local subnet.
6-37
NPort S8000 Series
Switch Featured Functions
DHCP Relay Agent (Option 82)
Option 82 is used by the relay agent to insert additional information into the client’s DHCP request. The Relay
Agent Information option is inserted by the DHCP relay agent when forwarding client-originated DHCP packets
to a DHCP server. Servers can recognize the Relay Agent Information option and use the information to
implement IP addresses to Clients.
When Option 82 is enabled on the switch, a subscriber device is identified by the switch port through which it
connects to the network (in addition to its MAC address). Multiple hosts on the subscriber LAN can be connected
to the same port on the access switch and are uniquely identified.
The Option 82 information contains 2 sub-options: Circuit ID and Remote ID, which define the relationship
between end device IP and the DHCP Option 82 server. The “Circuit ID” is a 4-byte number generated by the
Ethernet switch—a combination of physical port number and VLAN ID. The format of the “Circuit ID” is as
described below:
FF–VV–VV–PP
Where the first byte “FF” is fixed to “01”, the second and the third byte “VV-VV” is formed by the port VLAN ID
in hex, and the last byte “PP” is formed by the port number in hex. For example,
01–00–0F–03 is the “Circuit ID” of port number 3 with port VLAN ID 15.
The “Remote ID” is to identify the relay agent itself and it can be one of the following:
1. The IP address of the relay agent.
2. The MAC address of the relay agent.
3. A combination of IP address and MAC address of the relay agent.
4. A user-defined string.
Using Diagnosis
The EDS provides two important tools for administrators to diagnose network systems.
6-38
NPort S8000 Series
Switch Featured Functions
Mirror Port
The Mirror port function can be used to monitor data being transmitted through a specific port. This is done
by setting up another port (the mirror port) to receive the same data being transmitted from, or both to and
from, the port under observation. This allows the network administrator to “sniff” the observed port and thus
keep tabs on network activity.
System Management
Misc. Network Settings
Accessible IP List
The NPort S8000 uses an IP address-based filtering method to control access to NPort S8000 units.
Accessible IP Settings allows you to add or remove “Legal” remote host IP addresses to prevent unauthorized
access. Access to the NPort S8000 is controlled by IP address. If a host’s IP address is in the accessible IP table,
then the host will be allowed access to the NPort S8000. You can allow one of the following cases by setting this
parameter:
•
Only one host with the specified IP address can access the NPort S8000
E.g., enter “192.168.1.1/255.255.255.255” to allow access to just the IP address 192.168.1.1.
6-39
NPort S8000 Series
•
Switch Featured Functions
Any host on a specific subnetwork can access the NPort S8000
E.g., enter “192.168.1.0/255.255.255.0” to allow access to all IPs on the subnet defined by this IP
address/subnet mask combination.
•
Any host can access the NPort S8000
Disable this function by deselecting the Enable the accessible IP list option. The following table shows
additional configuration examples:
Allowable Hosts
Input format
Any host
Disable
192.168.1.120
192.168.1.120 / 255.255.255.255
192.168.1.1 to 192.168.1.254
192.168.1.0 / 255.255.255.0
192.168.0.1 to 192.168.255.254
192.168.0.0 / 255.255.0.0
192.168.1.1 to 192.168.1.126
192.168.1.0 / 255.255.255.128
192.168.1.129 to 192.168.1.254
192.168.1.128 / 255.255.255.128
SysLog Server
Using Syslog
This function provides the event logs for the syslog server. The function supports 3 configurable syslog servers
and syslog server UDP port numbers. When an event occurs, the event will be sent as a syslog UDP packet to
the specified syslog servers.
Syslog Server 1
Setting
Description
Factory Default
IP Address
Enter the IP address of 1st Syslog Server used by your
None
network.
Port Destination
Enter the UDP port of 1st Syslog Server.
514
Setting
Description
Factory Default
IP Address
Enter the IP address of 2nd Syslog Server used by your
None
(1 to 65535)
Syslog Server 2
network.
Port Destination
Enter the UDP port of 2nd Syslog Server.
6-40
514
NPort S8000 Series
Switch Featured Functions
(1 to 65535)
Syslog Server 3
Setting
Description
Factory Default
IP Address
Enter the IP address of 3rd Syslog Server used by your
None
network.
Port Destination
Enter the UDP port of 3rd Syslog Server.
514
(1 to 65535)
NOTE
The following events will be recorded into the NPort S8000-508A/505A’s Event Log table, and will
then be sent to the specified Syslog Server:
1. Cold start
2. Warm start
3. Configuration change activated
4. Power 1/2 transition (Off ( On), Power 1/2 transition (On ( Off)
5. Authentication fail
6. Topology changed
7. Master setting is mismatched
8. DI 1/2 transition (Off ( On), DI 1/2 transition (On ( Off)
9. Port traffic overload
10. dot1x Auth Fail
11. Port link off / on
Local User Database
Local User Database Setup
The User Database may be used for to authenticate users for 802.1x access and is useful if you do not have an
external RADIUS server for authentication. The User Table allow to stores up to 32 entries, with fields for User
Name, Password, and Description. When setting the Local User Database as the authentication database, set
the database first.
Local User Database Setup
Setting
Description
Factory Default
User Name
User Name for Local User Database
None
Password for Local User Database
None
Description for Local User Database
None
(Max. 30 characters)
Password
(Max. 16 characters)
Description
6-41
NPort S8000 Series
Switch Featured Functions
(Max. 30 characters)
NOTE
The user name for the Local User Database is case-insensitive.
Port Access Control
Using Port Access Control
The NPort S8000 provides two kinds of Port-Based Access Controls. One is Static Port Lock and the other is IEEE
802.1X.
Static Port Lock
The NPort S8000 can also be configured to protect static MAC addresses for a specific port. With the Port Lock
function, these locked ports will not learn any additional addresses, but only allow traffic from preset static MAC
addresses, helping to block crackers and careless usage.
IEEE 802.1X
The IEEE 802.1X standard defines a protocol for client/server-based access control and authentication. The
protocol restricts unauthorized clients from connecting to a LAN through ports that are open to the Internet,
and which otherwise would be readily accessible. The purpose of the authentication server is to check each
client that requests access to the port. The client is only allowed access to the port if the client’s permission is
authenticated.
The IEEE 802.1X Concept
Three components are used to create an authentication mechanism based on 802.1X standards:
Client/Supplicant, Authentication Server, and Authenticator.
Supplicant: The end station that requests access to the LAN and switch services and responds to the requests
from the switch.
Authentication server: The server that performs the actual authentication of the supplicant.
Authenticator: Edge switch or wireless access point that acts as a proxy between the supplicant and the
authentication server, requesting identity information from the supplicant, verifying the information with the
authentication server, and relaying a response to the supplicant.
The NPort S8000 acts as an authenticator in the 802.1X environment. A supplicant and an authenticator
exchange EAPOL (Extensible Authentication Protocol over LAN) frames with each other. We can either use an
external RADIUS server as the authentication server, or implement the authentication server in the NPort
S8000 by using a Local User Database as the authentication look-up table. When we use an external RADIUS
server as the authentication server, the authenticator and the authentication server exchange EAP frames
between each other.
Authentication can be initiated either by the supplicant or the authenticator. When the supplicant initiates the
authentication process, it sends an “EAPOL-Start” frame to the authenticator. When the authenticator initiates
the authentication process or when it receives an “EAPOL Start” frame, it sends an “EAP Request/Identity”
frame to ask for the username of the supplicant. The following actions are described below:
6-42
NPort S8000 Series
Switch Featured Functions
1. When the supplicant receives an “EAP Request/Identity” frame, it sends an “EAP Response/Identity” frame
with its username back to the authenticator.
2. If the RADIUS server is used as the authentication server, the authenticator relays the “EAP
Response/Identity” frame from the supplicant by encapsulating it into a “RADIUS Access-Request” frame
and sends to the RADIUS server. When the authentication server receives the frame, it looks up its
database to check if the username exists. If the username is not present, the authentication server replies
with a “RADIUS Access-Reject” frame to the authenticator if the server is a RADIUS server or just indicates
failure to the authenticator if the Local User Database is used. The authenticator sends an “EAP-Failure”
frame to the supplicant.
3. The RADIUS server sends a “RADIUS Access-Challenge,” which contains an “EAP Request” with an
authentication type to the authenticator to ask for the password from the client. RFC 2284 defines several
EAP authentication types, such as “MD5-Challenge,” “One-Time Password,” and “Generic Token Card.”
Currently, only “MD5-Challenge” is supported. If the Local User Database is used, this step is skipped.
4. The authenticator sends an “EAP Request/MD5-Challenge” frame to the supplicant. If the RADIUS server is
used, the “EAP Request/MD5-Challenge” frame is retrieved directly from the “RADIUS Access-Challenge”
frame.
5. The supplicant responds to the “EAP Request/MD5-Challenge” by sending an “EAP
Response/MD5-Challenge” frame that encapsulates the user’s password using the MD5 hash algorithm.
6. If the RADIUS server is used as the authentication server, the authenticator relays the “EAP
Response/MD5-Challenge” frame from the supplicant by encapsulating it into a “RADIUS Access-Request”
frame along with a “Shared Secret,” which must be the same within the authenticator and the RADIUS
server, and sends the frame to the RADIUS server. The RADIUS server checks against the password with its
database, and replies with “RADIUS Access-Accept” or “RADIUS Access-Reject” to the authenticator. If the
Local User Database is used, the password is checked against its database and indicates success or failure
to the authenticator.
7. The authenticator sends “EAP Success” or “EAP Failure” based on the reply from the authentication server.
Configuring Static Port Lock
The NPort S8000 supports adding unicast groups manually if required.
6-43
NPort S8000 Series
Switch Featured Functions
Setting
Description
Factory Default
MAC Address
Add the static unicast MAC address into the address table.
None
Port
Fix the static address with a dedicated port.
1
Configuring IEEE 802.1X
Database Option
Setting
Description
Local
Select this option when setting the Local User Database as the Local
Factory Default
(Max. 32 users)
authentication database.
Radius
Select this option to set an external RADIUS server as the
Local
authentication database. The authentication mechanism is
“EAP-MD5.”
Radius, Local
Select this option to make an external RADIUS server as the
authentication database with first priority. The authentication
mechanism is “EAP-MD5.” The second priority is to set the Local
6-44
Local
NPort S8000 Series
Switch Featured Functions
User Database as the authentication database.
Re-Auth
Setting
Enable/Disable
Description
Factory Default
Select to require re-authentication of the client after a preset
Disable
time period of no activity has elapsed.
Radius Server
Setting
Description
Factory Default
IP address or domain
The IP address or domain name of the RADIUS server
localhost
Description
Factory Default
Numerical
Specify how frequently the end stations need to reenter
3600
(60-65535 sec.)
usernames and passwords in order to stay connected.
name
Re-Auth Period
Setting
Server Port
Setting
Description
Factory Default
Numerical
The UDP port of the RADIUS Server
1812
Description
Factory Default
Shared Key
Setting
alphanumeric (Max. 40 A key to be shared between the external RADIUS server and
characters)
None
The NPort S8000. Both ends must be configured to use the
same key.
802.1X
Setting
Description
Factory Default
Enable/Disable
Select the option under the 802.1X column to enable IEEE
Disable
802.1X for one or more ports. All end stations must enter
usernames and passwords before access to these ports is
allowed.
Auto Warning Settings
Using Auto Warning
Since industrial Ethernet devices are often located at the endpoints of a system, these devices will not always
know what is happening elsewhere on the network. This means that an industrial Ethernet switch that connects
to these devices must provide system maintainers with real-time alarm messages. Even when control
engineers are out of the control room for an extended period of time, they can still be informed of the status of
devices almost instantaneously when exceptions occur. The NPort S8000 supports different approaches to
warn engineers automatically, such as by using email and relay output. It also supports two digital inputs to
integrate sensors into your system to automate alarms using email and relay output.
On the Event Settings page, you may configure how administrators are notified of certain system, network, and
configuration events. Depending on the event, different options for automatic notification are available, as
shown above. Mail refers to sending an e-mail to a specified address. Trap refers to sending an SNMP Trap.
Configuring E-Mail Alert
The Auto Email Warning function uses e-mail to alert the user when certain user-configured events take place.
Three basic steps are required to set up the Auto Warning function:
6-45
NPort S8000 Series
Switch Featured Functions
1. Configuring Email Event Types
Select the desired Event types from the Console or Web Browser Event type page (a description of each
event type is given later in the Email Alarm Events setting subsection).
2. Configuring Email Settings
To configure the NPort S8000’s email setup from the Console interface or browser interface, enter your Mail
Server IP/Name (IP address or name), Account Name, Account Password, Retype New Password, and the
email address to which warning messages will be sent.
3. Activate your settings and if necessary, test the email
After configuring and activating your NPort S8000’s Event Types and Email Setup, you can use the Test
Email function to see if your e-mail addresses and mail server address have been properly configured.
Mail Server IP/Name
Setting
Description
Factory Default
IP address
The IP Address of your email server.
None
Setting
Description
Factory Default
Max. 45 Characters
Your email account name (typically your user name)
None
Setting
Description
Factory Default
Disable/Enable to
To reset the Password from the Web Browser interface, click
Disable
change Password
the Change password check-box, type the Old Password, type
Account Name
Account Password
the New Password, retype the New password, and then click
Activate; Max. 45 Characters.
Old Password
New Password
Type the current password when changing the password
None
Type new password when enabled to change password; Max.
None
45 Characters.
Confirm Password
If you type a new password in the Password field, you will be
None
required to retype the password in the Retype new password
field before updating the new password.
Email Address
Setting
Description
Factory Default
Max. 30 characters
You can set up to 4 email addresses to receive alarm emails
None
from the NPort S8000.
6-46
NPort S8000 Series
Switch Featured Functions
Send Test Email
After configuring the email settings, you should first click Activate to activate those settings, and then click
Send Test Email to verify that the settings are correct.
NOTE
Auto warning e-mail messages will be sent through an authentication protected SMTP server that supports the
CRAM-MD5, LOGIN, and PLAIN methods of SASL (Simple Authentication and Security Layer) authentication
mechanism.
We strongly recommend not entering your Account Name and Account Password if auto warning e-mail
messages can be delivered without using an authentication mechanism.
Configuring SNMP
The NPort S8000 supports SNMP V1/V2c/V3. SNMP V1, and SNMP V2c use a community string match for
authentication, which means that SNMP servers access all objects with read-only or read/write permissions
using the community string public/private (default value). SNMP V3, which requires you to select an
authentication level of MD5 or SHA, is the most secure protocol. You can also enable data encryption to
enhance data security.
SNMP security modes and security levels supported by the NPort S8000 are shown in the following table. Select
the security mode and level that will be used to communicate between the SNMP agent and manager.
Protocol
UI Setting
Version
Authentication
Data Encryption
Method
Type
SNMP V1,
V1, V2c Read
V2c
Community
V1, V2c
Community string No
Use a community string match for
authentication
Community string No
Write/Read
Use a community string match for
authentication
Community
SNMP V3
No-Auth
No
No
MD5 or SHA
Authentication
No
Use account with admin or user to
access objects
Provides authentication based on
based on MD5 or
HMAC-MD5, or HMAC-SHA
SHA
algorithms. 8-character passwords
are the minimum requirement for
authentication.
MD5 or SHA
Authentication
Data encryption
Provides authentication based on
based on MD5 or
key
HMAC-MD5 or HMAC-SHA algorithms,
and data encryption key. 8-character
SHA
passwords and a data encryption key
are the minimum requirements for
authentication and encryption.
These parameters are configured on the SNMP page. A more detailed explanation of each parameter follows.
6-47
NPort S8000 Series
Switch Featured Functions
SNMP Read/Write Settings
SNMP agent version: The NPort S8000 supports SNMP V1, V2c, and V3.
V1, V2c Read community (default=public): This is a text password mechanism that is used to weakly
authenticate queries to agents of managed network devices.
V1, V2c Write/Read community (default=private): This is a text password mechanism that is used to
weakly authenticate changes to agents of managed network devices.
Read/write User name: Use this optional field to identify the user name for the specified level of access.
Read/write Authentication mode (default=No-Auth): Use this field to select MD5 or SHA as the method
of password encryption for the specified level of access, or to disable authentication
Read/write Password: Use this field to set the password for the specified level of access.
Read/write Privacy mode (default=Disable): Use this field to enable and disable DES data encryption for
the specified level of access.
6-48
NPort S8000 Series
Switch Featured Functions
Read/write Privacy: Use this field to define the encryption key for the specified level of access.
Read only: Read only authentication mode allows you to configure the authentication mode for read/write
access. For each level of access, you may configure the following:
Read/only User name: Use this optional field to identify the user name for the specified level of access.
Read/only Authentication mode (default=No-Auth): Use this field to select MD5 or SHA as the method of
password encryption for the specified level of access, or to disable authentication.
Read/only Password: Use this field to set the password for the specified level of access.
Read/only Privacy mode (default=Disable): Use this field to enable and disable DES data encryption for
the specified level of access.
Read/only Privacy: Use this field to define the encryption key for the specified level of access.
1st Trap Server IP/Name: Enter the IP address or the name of the 1st Trap Server used by your network.
1st Trap Community: Use a community string match for authentication (maximum of 30 characters).
2nd Trap Server IP/Name: Enter the IP address or the name of the 2nd Trap Server used by your network.
2nd Trap Community: Use a community string match for authentication (maximum of 30 characters).
Retries (Inform mode select): Enter the Inform Retry number Enter the numbers of retries before
Time out (Inform mode select): Enter Inform Timeout window
E-mail Event Settings
Event Types can be divided into three basic groups: System Events, Serial Port Events and Ethernet Port
Events.
System Events
Warning e-mail is sent when…
System Cold Start
Power is cut off and then reconnected.
System Warm Start
The NPort S8000 is rebooted, such as when network parameters
are changed (IP address, subnet mask, etc.).
Power Transition (OnOff)
The NPort S8000 is powered down.
Power Transition (OffOn)
The NPort S8000 is powered up.
DI1 (OnOff)
Digital Input 1 is triggered by on to off transition
6-49
NPort S8000 Series
Switch Featured Functions
DI1 (OffOn)
Digital Input 1 is triggered by off to on transition
DI2 (OnOff)
Digital Input 2 is triggered by on to off transition
DI2 (OffOn)
Digital Input 2 is triggered by off to on transition
Configuration Change Activated
A configuration item has been changed.
Authentication Failure
An incorrect password is entered.
Comm. Redundancy Topology Changed
Spanning Tree Protocol switches have changed their position
(applies only to the root of the tree).
The Master of the Turbo Ring has changed or the backup path is
activated.
Serial Port Events
DCD changed
Warning e-mail is sent when…
A change in the DCD (Data Carrier Detect) signal indicates that the modem
connection status has changed. For example, if the DCD signal changes to low, it
indicates that the connection line is down. When the DCD signal changes to low, the
NPort S8000 will automatically send a warning to the administrator as configured on
the Serial Event Settings page.
DSR changed
A change in the DSR (Data Set Ready) signal indicates that the data communication
equipment is powered off. For example, if the DSR signal changes to low, it indicates
that the data communication equipment is powered down. When the DSR signal
changes to low, the NPort S8000 will automatically send a warning to the
administrator as configured on the Serial Event Settings page.
Ethernet Port Events
Warning e-mail is sent when…
Link-ON
The port is connected to another device.
Link-OFF
The port is disconnected (e.g., the cable is pulled out, or the opposing device
shuts down).
Traffic-Overload
The port’s traffic surpasses the Traffic-Threshold for that port (provided this
item is Enabled).
Traffic-Threshold (%)
Enter a non-zero number if the port’s Traffic-Overload item is Enabled.
Traffic-Duration (sec.)
A Traffic-Overload warning is sent every Traffic-Duration seconds if the
average Traffic-Threshold is surpassed during that time period.
NOTE
The default “Warning e-mail message” is empty in the sender field. It is recommended to set a message to help
you to recognize the Warning e-mail message.
6-50
NPort S8000 Series
Switch Featured Functions
SNMP Trap
System Events
Warning e-mail is sent when…
System Cold Start
Power is cut off and then reconnected.
System Warm Start
The NPort S8000 is rebooted, such as when network parameters
are changed (IP address, subnet mask, etc.).
Power Transition (OnOff)
The NPort S8000 is powered down.
Power Transition (OffOn)
The NPort S8000 is powered up.
DI1 (OnOff)
Digital Input 1 is triggered by on to off transition
DI1 (OffOn)
Digital Input 1 is triggered by off to on transition
DI2 (OnOff)
Digital Input 2 is triggered by on to off transition
DI2 (OffOn)
Digital Input 2 is triggered by off to on transition
Configuration Change Activated
A configuration item has been changed.
Authentication Failure
An incorrect password is entered.
Comm. Redundancy Topology Changed
Spanning Tree Protocol switches have changed their position
(applies only to the root of the tree).
The Master of the Turbo Ring has changed or the backup path is
activated.
Serial Port Events
Warning e-mail is sent when…
DCD changed
A change in the DCD (Data Carrier Detect) signal indicates that the modem
connection status has changed. For example, if the DCD signal changes to low, it
indicates that the connection line is down. When the DCD signal changes to low, the
NPort S8000 will automatically send a warning to the administrator as configured on
the Serial Event Settings page.
DSR changed
A change in the DSR (Data Set Ready) signal indicates that the data communication
equipment is powered off. For example, if the DSR signal changes to low, it indicates
that the data communication equipment is powered down. When the DSR signal
changes to low, the NPort S8000 will automatically send a warning to the
administrator as configured on the Serial Event Settings page.
6-51
NPort S8000 Series
Switch Featured Functions
Ethernet Port Events
Warning e-mail is sent when…
Link-ON
The port is connected to another device.
Link-OFF
The port is disconnected (e.g., the cable is pulled out, or the opposing device
shuts down).
Traffic-Overload
The port’s traffic surpasses the Traffic-Threshold for that port (provided this
item is Enabled).
Traffic-Threshold (%)
Enter a non-zero number if the port’s Traffic-Overload item is Enabled.
Traffic-Duration (sec.)
A Traffic-Overload warning is sent every Traffic-Duration seconds if the
average Traffic-Threshold is surpassed during that time period.
NOTE
The default “Warning e-mail message” is empty in the sender field. It is recommended to set a message to help
you to recognize the Warning e-mail message.
Relay Alarm Settings
Configuring Relay Warning
The Auto Relay Warning function uses relay output to alert the user when certain user-configured events take
place. There are two basic steps required to set up the Relay Warning function:
1. Configuring Relay Event Types
Select the desired Event types from the Console or Web Browser Event type page (a description of each
event type is given later in the Relay Alarm Events setting subsection).
2. Activate your settings
After completing the configuration procedure, you will need to activate your NPort S8000’s Relay Event
Types.
Event Types can be divided into two basic groups: System Events and Ethernet Port Events. System Events
are related to the overall function of the NPort S8000, whereas Ethernet Port Events are related to the activity
of a specific port.
The NPort S8000 supports two relay outputs. You can configure which relay output is related to which events.
This helps administrators identify the importance of the different events.
Override relay alarm settings
Select this option to override the relay warning setting temporarily. Releasing the relay output will allow
administrators to fix any problems with the warning condition.
6-52
NPort S8000 Series
Switch Featured Functions
System Events
Factory Default
Override relay 1 Warning settings
Non-check
Override relay 2 Warning settings
Non-check
System Events
Warning Relay output is triggered when…
Power Input 1 failure
Disable
Default
(OnOff)
Relay 1
Relay 1 is triggered by on to off transition
Relay 2
Relay 2 is triggered by on to off transition
Power Input 2 failure
Disable
Default
(OnOff)
Relay 1
Relay 1 is triggered by on to off transition
Relay 2
Relay 2 is triggered by on to off transition
DI1 (OnOff)
Disable
Default
Relay 1
Digital Input 1 is triggered by on to off transition and enable
Relay 1
Relay 2
Digital Input 1 is triggered by on to off transition and enable
Relay 2.
DI1 (OffOn)
Disable
Default
Relay 1
Digital Input 1 is triggered by off to on transition and enable
Relay 1
Relay 2
Digital Input 1 is triggered by off to on transition and enable
Relay 2.
DI2 (OnOff)
Disable
Default
Relay 1
Digital Input 2 is triggered by on to off transition and enable
Relay 1
Relay 2
Digital Input 2 is triggered by on to off transition and enable
Relay 2.
DI2 (OffOn)
Disable
Default
Relay 1
Digital Input 2 is triggered by off to on transition and enable
Relay 1
Relay 2
Digital Input 2 is triggered by off to on transition and enable
Relay 2.
Port Events
Warning Relay output is triggered when…
Link-ON
The port is connected to another device.
Link-OFF
The port is disconnected (e.g., the cable is pulled out, or the opposing device
shuts down).
Traffic-Overload
The port’s traffic surpasses the Traffic-Threshold for that port (provided this item
Traffic-Threshold (%)
Enter a non-zero number if the port’s Traffic-Overload item is Enabled.
Traffic-Duration (sec.)
A Traffic-Overload warning is sent every Traffic-Duration seconds if the average
is Enabled).
Traffic-Threshold is surpassed during that time period.
NOTE
The Traffic-Overload, Traffic-Threshold (%), and Traffic-Duration (sec) Port Event items are related. If
you Enable the Traffic-Overload event, then be sure to enter a non-zero Traffic-Threshold percentage, as well
as a Traffic-Duration between 1 and 300 seconds.
System Log Settings
System Log Settings allow the administrator to customize which network events are logged by the NPort S8000.
Events are grouped into four categories, known as event groups, and the administrator selects which groups to
log under Local Log. The actual system events that would be logged for each system group are listed under
summary. For example, if System was enabled, then System Cold Start events and System Warm Start events
would be logged.
6-53
NPort S8000 Series
Switch Featured Functions
Local Log
Keep the log into the flash of NPort S8000 up to 512 items.
Remote Log
Keep the log into the remote defined Log Server.
You will need to assign a remote Log Server in the System Management / Misc.
Network Settings / Remote Log Settings if remote log is checked.
System
System Cold Start
NPort S8000 cold start.
System Warm Start
NPort S8000 warm start.
Power Transition
The NPort S8000 is powered up or down.
DI On/Off
Digital Input 1 is triggered
Network
DHCP/BOOTP/Get IP/Renew
IP of the NPort S8000 is refreshed.
Mail Fail
Failed to deliver the E-mail.
NTP Connect Fail
The NPot S8455I-MM-SC failed to connect to the NTP Server.
IP Conflict
There is an IP conflict on the local network.
Network Link Down/UP
LAN 1 Link is down.
Communication Redundancy
When the status of Ring is changed or Master device is mismatched
Topology Changed/Master
Mismatched
Config
Authentication Fail
IP Changed
Static IP address was changed.
Config Changed
The NPort S8000’s configuration was changed.
Firmware Upgrade
Firmware was upgraded.
Config Import
Config was impoted.
Config Export
Config was expoted.
OpMode
Connect
Op Mode is in used
Disconnect
Op Mode switched from in use to disconnect.
Restart
Serial port was restarted.
6-54
NPort S8000 Series
Switch Featured Functions
Maintenance
Console Settings
Config
HTTP console
HTTP console enable/disable
HTTPS console
HTTPS console enable/disable
Telnet console
Telnet console enable/disable
SSH console
SSH console enable/disable
Reset button
Always Enable
Reset button disable after 60 sec uptime
Auto refresh time
Monitor page refresh time
Ping
The Ping function uses the ping command to give users a simple but powerful tool for troubleshooting network
problems. The function’s most unique feature is that even though the ping command is entered from the user’s
PC keyboard, the actual ping command originates from NPort S8000 itself. In this way, the user can essentially
control the NPort S8000 and send ping commands out through its ports.
To use the Ping function, type in the desired IP address, and then press Enter from the Console utility, or click
Ping when using the Web Browser interface.
6-55
NPort S8000 Series
Switch Featured Functions
Update System Files from Local PC
The NPort S8000 can share or back up its configuration by exporting all settings to a file, which can then be
imported into another NPort S8000.
To import a configuration, go to System Management  Maintenance  Configuration Import. Enter the
configuration file path/name and click Submit. The NPort S8000’s configuration settings will be updated
according to the configuration file. If you also wish to import the IP configuration (i.e., the NPort S8000’s IP
address, netmask, gateway, etc.), make sure that Import all configurations including IP configurations
is checked off.
To export a configuration, go to System Management  Maintenance  Configuration Export and click
Download. A standard download window will appear, and you will be able to download the configuration into
a file name and location of your choice.
Configuration File
To export the configuration file of this NPort S8000, click Export to save it to the local host.
Log File
To export the Log file of this NPort S8000, click Export and save it to the local host.
NOTE
Some operating systems will open the configuration file and log file directly in the web page. In such cases,
right click Export to save as a file.
Upgrade Firmware
To import the firmware file of this NPort S8000, click Browse to select the firmware file already saved on your
computer. The upgrade procedure will proceed automatically after clicking Import.
Upload Configuration Data
To import the configuration file of this NPort S8000, click Browse to select the configuration file already saved
on your computer. The upgrade procedure will proceed automatically after clicking Import.
Load Factory Default
This function will reset all of NPort S8000’s settings to the factory default values. All previous settings including
the console password will be lost. If you wish to keep the NPort S8000 IP address, netmask, and other IP
settings, make sure Keep IP settings is checked off before loading the factory defaults.
The Factory Default function is included to give users a quick way of restoring the NPort S8000’s configuration
settings to their factory default values. This function is available in the Console utility (serial or Telnet), and
Web Browser interface.
6-56
NPort S8000 Series
NOTE
Switch Featured Functions
After activating the Factory Default function, you will need to use the default network settings to re-establish
a web-browser or Telnet connection with your NPort S8000.
Change Password
For all changes to the NPort S8000’s password protection settings, you will first need to enter the old password.
Leave this blank if you are setting up password protection for the first time. To set up a new password or change
the existing password, enter your desired password under both New password and Confirm password. To
remove password protection, leave the New password and Confirm password boxes blank.
6-57
NPort S8000 Series
Switch Featured Functions
Mirror Port Settings
The Mirror port function can be used to monitor data being transmitted through a specific port. This is done
by setting up another port (the mirror port) to receive the same data being transmitted from, or both to and
from, the port under observation. This allows the network administrator to “sniff” the observed port and thus
keep tabs on network activity.
Perform the following steps to set up the Mirror Port function:
1. Configure the EDS’s Mirror Port function from either the Console utility or Web Browser interface. You will
need to configure three settings:
Monitored Port
Select the port number of the port whose network activity will be monitored.
Mirror Port
Select the port number of the port that will be used to monitor the activity of the
monitored port.
Watch Direction
Select one of the following three watch direction options:
•
Input data stream
Select this option to monitor only those data packets coming in through the
EDS’s port.
•
Output data stream
Select this option to monitor only those data packets being sent out through the
EDS’s port.
•
Bi-directional
Select this option to monitor data packets both coming into, and being sent out
through, the EDS’s port.
2. Be sure to activate your settings before exiting.

When using the Web Browser interface, activate by clicking Activate.

When using the Console utility, activate by first highlighting the Activate menu option, and then press Enter.
You should receive the Mirror port settings are now active! (Press any key to continue) message.
TFTP Settings
System File Update—By Remote TFTP
The NPort S8000 supports saving your configuration file to a remote TFTP server or local host to allow other
NPort S8000 switches to use the same configuration at a later time, or saving the Log file for future reference.
Loading pre-saved firmware or a configuration file from the TFTP server or local host is also supported for easy
upgrading or configuration of the NPort S8000.
6-58
NPort S8000 Series
Switch Featured Functions
TFTP Server IP/Name
Setting
Description
Factory Default
IP Address of TFTP
The IP or name of the remote TFTP server. Must be set up
None
Server
before downloading or uploading files.
Configuration Files Path and Name
Setting
Description
Factory Default
Max. 40 Characters
The path and file name of the NPort S8000’s configuration file in None
the TFTP server.
Firmware Files Path and Name
Setting
Description
Factory Default
Max. 40 Characters
The path and file name of the NPort S8000’s firmware file.
None
Log Files Path and Name
Setting
Description
Factory Default
Max. 40 Characters
The path and file name of the NPort S8000’s log file
None
After setting up the desired path and file name, click Activate to save the setting, and then click Download to
download the prepared file from the remote TFTP server, or click Upload to upload the desired file to the
remote TFTP server.
Dip Switch Settings
Turbo Ring DIP Switches
The Turbo Ring DIP Switch page allows users to disable the four DIP switches located on the NPort S8000’s
outer casing. When enabled, the DIP switches can be used to configure basic settings for either the “Turbo Ring”
protocol or “Turbo Ring V2” protocol. A complete description of the settings is given below.
NOTE
The proprietary “Turbo Ring” protocol (recovery time < 300 ms) was developed by Moxa in 2003 to provide
better network reliability and faster recovery time for redundant ring topologies. The “Turbo Ring V2” protocol
(recovery time < 20 ms), which was released in 2007, supports additional redundant ring architectures.
In this manual, we use the terminology “Turbo Ring” ring and “Turbo Ring V2” ring to differentiate between
rings configured for one or the other of these protocols.
For a detailed description of “Turbo Ring” and “Turbo Ring V2,” please refer to the Using Communication
Redundancy section later in this chapter.
6-59
NPort S8000 Series
Switch Featured Functions
How to Enable or Disable the Turbo Ring DIP Switches
Disable the Turbo Ring DIP Switch
Setting
Description
Enable the Turbo Ring
The four DIP switches are enabled when the “Disable the Turbo Not checked (i.e.,
Factory Default
DIP Switches
Ring DIP Switch” box is not checked.
the Turbo Ring DIP
Disable the Turbo Ring The four DIP switches are disabled when the “Disable the Turbo Switches are
DIP Switches
Ring DIP Switch” box is checked.
enabled by default)
Set DIP switch as Turbo Ring / Set DIP switch as Turbo Ring V2
Setting
Description
Factory Default
Set DIP switch as Turbo Select this option to enable the Turbo Ring DIP switches to
Ring
configure the NPort S8000 for a “Turbo Ring” ring.
This is the default if
you do NOT reset
the switch to factory
default settings
(provided you
upgraded the
firmware for Turbo
Ring V2).
Set DIP switch as Turbo Select this option to enable the Turbo Ring DIP switches to
This is the default if
Ring V2
you DO reset the
configure the NPort S8000 for a “Turbo Ring V2” ring.
switch to factory
default settings
(provided you
upgraded the
firmware for Turbo
Ring V2).
How to Configure the Turbo Ring DIP Switches
The Turbo Ring DIP Switches are set to the OFF position at the factory.
NOTE
The four DIP Switches are used to configure both the “Turbo Ring” and “Turbo Ring V2” protocols, depending
on which protocol is active. To select which protocol the NPort S8000 will use, start the user interface software,
and then use the left menu to navigate to the Communication Redundancy page. To use one of the Turbo Ring
protocols for the NPort S8000, select either “Turbo Ring” or “Turbo Ring V2” in the Redundancy Protocol
drop-down box. See the Configuring “Turbo Ring” and “Turbo Ring V2” section in this chapter for details.
The following tables show how to use the DIP switches to configure the NPort S8000 for “Turbo Ring” or “Turbo
Ring V2.”
6-60
NPort S8000 Series
NOTE
Switch Featured Functions
DIP switch 4 must be set to the ON position to enable DIP switches 1, 2, and 3. If DIP switch 4 is set to the “OFF”
position, then DIP switches 1, 2, and 3 will all be disabled.
Turbo Ring” DIP Switch Settings
DIP 1
Reserved for future use.
DIP 2
DIP 3
ON: Enables this NPort
ON: Enables the default
S8000 as the Ring Master. “Ring Coupling” ports.
DIP 4
ON: Activates DIP
switches 1, 2, 3 to
configure “Turbo Ring”
settings.
OFF: This NPort S8000 will OFF: Do not use this NPort OFF: DIP switches 1, 2, 3
not be the Ring Master.
S8000 as the ring coupler. will be disabled.
“Turbo Ring V2” DIP Switch Settings
DIP 1
DIP 2
DIP 3
DIP 4
ON: Enables the default
ON: Enables this NPort
ON: Enables the default
ON: Activates DIP
“Ring Coupling (backup)”
S8000 as the Ring Master. “Ring Coupling” port.
port.
switches 1, 2, 3 to
configure “Turbo Ring V2”
settings.
OFF: Enables the default
OFF: This NPort S8000 will OFF: Do not use this NPort OFF: DIP switches 1, 2, 3
“Ring Coupling (primary)” not be the Ring Master.
S8000 as a ring coupler.
will be disabled.
port.
NOTE
The DIP 1 setting will only be active if DIP 3 is in the ON position. If you set DIP 3 to OFF, then the default Ring
Coupling port will NOT be enabled, even if DIP 1 is ON.
NOTE
The Turbo Ring Ports and Coupling Ports will be added automatically to all VLANs if you set DIP Switch 4 to the
“ON” position.
NOTE
If you do not enable any of the NPort S8000 switches to be the Ring Master, the Turbo Ring protocol will
automatically choose the NPort S8000 with the smallest MAC address range to be the Ring Master. If you
accidentally enable more than one NPort S8000 to be the Ring Master, these NPort S8000 switches will
auto-negotiate to determine which one will be the Ring Master.
NOTE
If you use the browser interface to enable the DIP switches (by un-checking the “Disable the Turbo Ring DIP
switch” checkbox), and then flip DIP switch 4 from ON to OFF, the Ring Ports and Coupling Ports that were
added to all VLANs will be restored to their previous software settings. (For details, please refer to the “Using
Virtual LANs” section of this manual).
System Monitoring
Serial Status
Serial to Network Connection
Go to Serial to Network Connections under Serial Status to view the operation mode and status of each
connection, for each serial port. All monitor functions will refresh automatically every 5 seconds.
6-61
NPort S8000 Series
Switch Featured Functions
Serial Port Status
Go to Serial Port Status under Serial Status to view the current status of each serial port.
Serial Port Status  Buffering.
Monitor port buffering usage (bytes) of each serial port.
Serial Port Error Count
Go to Serial Port Error Count under Serial Status to view the error count for each serial port.
Frame: Framing error; indicates that the received character did not have a valid stop bit.
Parity: Parity error; indicates that the received data character does not match the parity selected.
Overrun: The NPort is unable to hand received data to a hardware buffer because the input rate exceeds the
NPort’s ability to handle the data.
Break: Break interrupt; indicates that the received data input was held low for longer than a full-word
transmission time. A full-word transmission time is defined as the total time to transmit the start, data, parity,
and stop bits.
Serial Port Settings
Go to Serial Port Settings under Serial Status to view a summary of the settings for each serial port.
6-62
NPort S8000 Series
Switch Featured Functions
System Status
System Information
This page illustrate the status of system
Light
Status
Default
Power
Lighting when power is NO
blind
DI
Lighting when triggered
blind
DIP Switch
Lighting when DIP switch Set to ON
blind
Network Connections
Go to Network Connections under System Status to view network connection information.
6-63
NPort S8000 Series
Switch Featured Functions
Event Log
Bootup
This field shows how many times the NPort S8000 has been rebooted or cold started.
Date
The date is updated based on how the current date is set in the “Basic Setting” page.
Time
The time is updated based on how the current time is set in the “Basic Setting” page.
System Startup Time The system startup time related to this event.
Events
NOTE
Events that have occurred.
The following events will be recorded into the NPort S8000’s Event Log table:
1. Cold start
2. Warm start
3. Configuration change activated
4. Power 1/2 transition (Off ( On), Power 1/2 transition (On ( Off)
5. Authentication fail
6. Topology changed
7. Master setting is mismatched
8. DI 1/2 transition (Off ( On), DI 1/2 transition (On ( Off)
9. Port traffic overload
10. dot1x Auth Fail
11. Port link off / on
Ethernet Status
MAC Address List
This section explains the information provided by the NPort S8000’s MAC address table.
The MAC Address table can be configured to display the following NPort S8000 MAC address groups.
ALL
Select this item to show all NPort S8000 MAC addresses
ALL Learned
Select this item to show all NPort S8000 Learned MAC addresses
6-64
NPort S8000 Series
ALL Static Lock
ALL Static
Switch Featured Functions
Select this item to show all NPort S8000 Static Lock MAC addresses
Select this item to show all NPort S8000 Static/Static Lock /Static Multicast MAC
addresses
ALL Static Multicast
Select this item to show all NPort S8000 Static Multicast MAC addresses
Port ( 1-5)
Select this item to show all MAC addresses of dedicated ports
The table will display the following information:
MAC
This field shows the MAC address
Type
This field shows the type of this MAC address
Port
This field shows the port that this MAC address belongs to
IGMP Table
The NPort S8000 displays the current active IGMP groups that were detected.
The information includes VID, Auto-learned Multicast Router Port, Static Multicast Router Port,
Querier Connected Port, and the IP and MAC addresses of active IGMP groups.
GMRP Table
The NPort S8000 displays the current active GMRP groups that were detected.
Setting
Description
Fixed Ports
This multicast address is defined by static multicast.
Learned Ports
This multicast address is learned by GMRP.
802.1X Reauth
6-65
NPort S8000 Series
Switch Featured Functions
The NPort S8000 can force connected devices to be re-authorized manually.
Port Access Control Table
The port status will indicate whether the access is authorized or unauthorized.
Warning List
Use this table to see if any relay alarms have been issued.
Ethernet Monitor
This page illustrates the data transmission status of Ethernet. Check one of the four options, Total Packets, TX
Packets, RX Packets, or Error Packets, to show the transmission activity of specific types of packets.
Check the Port Status to show the status of Ethernet port.
Trunk Table
6-66
NPort S8000 Series
Switch Featured Functions
Setting
Description
Trunk Group
Displays the Trunk Type and Trunk Group.
Member Port
Display which member ports belong to the trunk group.
Status
Success means port trunking is working properly.
Fail means port trunking is not working properly.
Standby means port trunking is working as a standby port. When there are more
than eight ports trunked as a trunking group, the 9th port will be the standby port.
VLAN Table
In the 802.1Q VLAN table, you can review the VLAN groups that were created, Joined Access Ports, and Trunk
Ports. In the Port-based VLAN table, you can review the VLAN group and Joined port.
NOTE
The physical network can have a maximum of 64 VLAN settings.
Communication Redundancy Status
This page shows the status of communication redundancy.
RSTP
Explanation of “Current Status” Items
Now Active
Shows which communication protocol is in use: Turbo Ring, Turbo Ring V2, RSTP
Ring 1/2—Status
Shows Healthy if the ring is operating normally, and shows Break if the ring’s backup link is active.
Ring 1/2—Master/Slave
Indicates whether or not this NPort S8000 is the Master of the Turbo Ring. (This field appears only when
selected to operate in Turbo Ring or Turbo Ring V2 mode.)
6-67
NPort S8000 Series
Now active
Switch Featured Functions
Indicate the in used communication protocol. It may be Turbo Ring, Turbo Ring V2,
RSTP, or none.
Root/Not root
Available when Redundancy protocol is set to RSTP mode.
Indicate NPort S8000 is in the Root of the Spanning Tree.
(The root is determined automatically).
Port 1 / Port 2
Indicates the current Spanning Tree status of these ports.
Port 3 / Port 4
“Forwarding” for normal transmission
Port 5
“Blocking” to block transmission.
Turbo Ring
Now active
Indicate the in used communication protocol. It may be Turbo Ring,
Master/Slave
Indicate NPort S8000 is in the Master mode or Slave mode of the Turbo
Turbo Ring V2, RSTP, or none.
Ring.
Redundant Ports Status
Link down
No connection
Blocked
This port is connected to a backup path and the path is
blocked
Forwarding
Normal transmission
Learning
Learning
Ring Coupling Ports Status
Enable or disable
Coupling Port
Indicate which port is used to be coupling port (port 1 to port 5). Available
when Ring Coupling in communication redundancy setting page is
enabled
Coupling Control Port
Indicate which port is used to be coupling control port (port 1 to port 5).
Available when Ring Coupling in communication redundancy setting page
is enabled
Turbo Ring 2
6-68
NPort S8000 Series
Now Active
Switch Featured Functions
Indicate the in used communication protocol. It may be Turbo Ring, Turbo Ring V2,
RSTP, or none.
Ring 1/2
Status
Healthy
The ring is operating normally
Break
The backup link is active in the Ring.
Master/Slave
Indicate NPort S8000 is in the Master mode or Slave mode of the Turbo Ring 2.
1st/2nd Ring Port Status Link down
Coupling Mode
No connection
Blocked
This port is connected to a backup path and the path is blocked
Forwarding
Normal transmission
Learning
Learning
Indicates current coupling mode
It may be None, Dual Homing, or Ring Coupling.
Coupling Port status
Indicate which port is used to be coupling port (port 1
to port 5). Available when
Ring Coupling in communication redundancy setting page is enabled
Restart
Restart System
Go to Restart System under Restart and then click Restart to restart the NPort S8000. Ensure that you save
all your configuration changes before you restart the system or else these changes will be lost.
Restart Serial Port
Go to Restart Ports under Restart and then select the ports to be restarted. Click Select All to select all the
ports. Click Submit to restart the selected ports.
6-69
7
7.
Software Installation/Configuration
The following topics are covered in this chapter:
 Overview
 NPort Windows Driver Manager
 Installing NPort Windows Driver Manager
 Using NPort Windows Driver Manager
 NPort Search Utility
 Installing NPort Search Utility
 Configuring NPort Search Utility
 Linux Real TTY Drivers
 Basic Procedures
 Hardware Setup
 Installing Linux Real TTY Driver Files
 Mapping TTY Ports
 Removing Mapped TTY Ports
 Removing Linux Driver Files
 The UNIX Fixed TTY Driver
 Installing the UNIX Driver
 Configuring the UNIX Driver
NPort S8000 Series
Software Installation/Configuration
Overview
The Documentation & Software CD included with your NPort S8000 is designed to make the installation and
configuration procedure easy and straightforward. This auto-run CD includes NPort Windows Driver Manager
(for COM mapping), NPort Search Utility (to broadcast search for all NPort S8000’s accessible over the network),
the NPort S8000 User’s Manual, and the NPort firmware upgrade utility.
NPort Windows Driver Manager
Installing NPort Windows Driver Manager
NPort Windows Driver Manager is intended for use with NPort S8000 serial ports that are set to Real COM mode.
The software manages the installation of drivers that allow you to map unused COM ports on your PC to serial
ports on the NPort S8000. These drivers are designed for use with Windows 98/ME/2000/XP/2003. When the
drivers are installed and configured, devices that are attached to serial ports on the NPort S8000 will be treated
as if they were attached to your PC’s own COM ports.
1. Click the INSTALL COM Driver button in the NPort Installation CD auto-run window to install the NPort
Windows Driver. Once the installation program starts running, click Yes to proceed.
2. Click Next when the Welcome screen opens, to proceed with the installation.
7-2
NPort S8000 Series
Software Installation/Configuration
Click Next to install program files to the default directory, or click Browse to select an alternate location.
3. Click Next to install the program’s shortcuts in the appropriate Start Menu folder.
7-3
NPort S8000 Series
Software Installation/Configuration
4. Click Next to proceed with the installation. The installer then displays a summary of the installation options.
5. Click Install to begin the installation. The setup window will report the progress of the installation. To
change the installation settings, click Back and navigate to the previous screen. The installer will display a
message that the software has not passed Windows Logo testing. This is shown as follows:
Click Continue Anyway to finish the installation.
7-4
NPort S8000 Series
Software Installation/Configuration
6. Click Finish to complete the installation of the NPort Windows Driver Manager.
Using NPort Windows Driver Manager
Real COM Mode
After you install NPort Windows Driver Manager, you can set up the NPort S8000’s serial ports as remote COM
ports for your PC host. Make sure that the serial port(s) on your NPort S8000 are set to Real COM mode when
mapping COM ports with the NPort Windows Driver Manager.
1. Go to Start  NPort Windows Driver Manager  NPort Windows Driver Manager to start the COM
mapping utility.
2. Click the Add icon.
7-5
NPort S8000 Series
Software Installation/Configuration
3. Click Search to search for NPort device servers. From the list that is generated, select the server to which
you will map COM ports, and then click OK.
4. Alternatively, you can select Input Manually and then manually enter the NPort IP Address, 1st Data Port,
1st Command Port, and Total Ports to which COM ports will be mapped. Click OK to proceed to the next step.
Note that the Add NPort page supports FQDN (Fully Qualified Domain Name), in which case the IP address
will be filled in automatically.
7-6
NPort S8000 Series
Software Installation/Configuration
5. COM ports and their mappings will appear in blue until they are activated. Activating the COM ports saves
the information in the host system registry and makes the COM port available for use. The host computer
will not have the ability to use the COM port until the COM ports are activated. Click Yes to activate the COM
ports at this time, or click No to activate the COM ports later.
6. A message will display during activation of each port, indicating that the software has not passed Windows
Logo certification. Click Continue Anyway to proceed.
7-7
NPort S8000 Series
Software Installation/Configuration
7. Ports that have been activated will appear in black.
Configure the mapped COM ports
For Real COM Mode, to re-configure the settings for a particular serial port on the NPort S8000 select the row
corresponding to the desired port and then click the Setting icon.
7-8
NPort S8000 Series
Software Installation/Configuration
1. On the Basic Setting window, use the COM Number drop-down list to select a COM number to be
assigned to the NPort S8000’s serial port that is being configured. Select the Auto Enumerating COM
Number for Selected Ports option to automatically assign available COM numbers in sequence to
selected serial ports. Note that ports that are “in use” will be labeled accordingly.
2. Click the Advanced Settings tab to modify Tx Mode, FIFO, and Flash Flush.
Tx Mode
Hi-Performance is the default for Tx mode. After the driver sends data to the NPort S8000, the driver
immediately issues a “Tx Empty” response to the program. Under Classical mode, the driver will not send the
“Tx Empty” response until after confirmation is received from the NPort S8000’s serial port. This causes lower
throughput. Classical mode is recommended if you want to ensure that all data is sent out before further
processing.
7-9
NPort S8000 Series
Software Installation/Configuration
FIFO
If FIFO is Disabled, the NPort S8000 will transmit one byte each time the Tx FIFO becomes empty, and an Rx
interrupt will be generated for each incoming byte. This will result in a faster response and lower throughput.
Network Timeout
You can use this option to prevent blocking if the target NPort is unavailable.
Auto Network Re-Connection
With this option enabled, the driver will repeatedly attempt to re-establish the TCP connection if the NPort
S8000 does not respond to background “check alive” packets.
Return error if network is unavailable
If this option is disabled, the driver will not return any error even when a connection cannot be established to
the NPort S8000. With this option enabled, calling the Win32 Comm function will result in the error return code
“STATUS_NETWORK_UNREACHABLE” when a connection cannot be established to the NPort S8000. This
usually means that your host’s network connection is down, perhaps due to a cable being disconnected.
However, if you can reach other network devices, it may be that the NPort S8000 is not powered on or is
disconnected. Note that Auto Network Re-Connection must be enabled in order to use this function.
Fast Flush (only flushes the local buffer)
For some applications, the user’s program will use the Win32 “PurgeComm()” function before it reads or writes
data. After a program uses this PurgeComm() function, the NPort driver continues to query the NPort’s
firmware several times to make sure no data is queued in the NPort’s firmware buffer, rather than just flushing
the local buffer. This design is used to satisfy some special considerations. However, it may take more time
(about several hundred milliseconds) than a native COM1 due to the additional time spent communicating
across the Ethernet. This is why PurgeComm() works significantly faster with native COM ports on the PC than
with mapped COM ports on the NPort S8000. In order to accommodate other applications that require a faster
response time, the new NPort driver implements a new Fast Flush option. By default, this function is enabled.
If you have disabled Fast Flush and find that COM ports mapped to the NPort S8000 perform markedly slower
than when using a native COM port, try to verify if “PurgeComm()” functions are used in your application. If so,
try enabling the Fast Flush function and see if there is a significant improvement in performance.
3. The Serial Parameters window in the following figure shows the default settings when the NPort S8000 is
powered on. However, the program can redefine the serial parameters to different values after the program
opens the port via Win 32 API.
7-10
NPort S8000 Series
Software Installation/Configuration
4. The Security function is available only for the NPort 6000 series and the NPort S8000 doesn’t support this
function.
5. The IPv6 Settings function is available only for the NPort 6000 series and the NPort S8000 doesn’t support
this function.
7-11
NPort S8000 Series
Software Installation/Configuration
6. To save the configuration to a text file, select Export from the COM Mapping menu. You will then be able
to import this configuration file to another host and use the same COM Mapping settings in the other host.
NPort Search Utility
Installing NPort Search Utility
1. Click the INSTALL UTILITY button in the NPort Installation CD auto-run window to install NPort Search
Utility. Once the program starts running, click Yes to proceed.
2. Click Settings when the Welcome screen opens, to proceed with the installation.
7-12
NPort S8000 Series
Software Installation/Configuration
3. Click Next to install program files to the default directory, or click Browse to select an alternate location.
4. Click Next to install the program’s shortcuts in the appropriate Start Menu folder.
7-13
NPort S8000 Series
Software Installation/Configuration
5. Click Next to proceed with the installation. The installer then displays a summary of the installation options.
6. Click Install to begin the installation. The setup window will report the progress of the installation. To
change the installation settings, click Back and navigate to the previous screen.
7. Click Finish to complete the installation of NPort Search Utility.
Configuring NPort Search Utility
The Broadcast Search function is used to locate all NPort S8000 servers that are connected to the same LAN as
your computer. After locating an NPort S8000, you will be able to change its IP address.
Since the Broadcast Search function searches by MAC address and not IP address, all NPort S8000 servers
connected to the LAN will be located, regardless of whether or not they are part of the same subnet as the host.
7-14
NPort S8000 Series
Software Installation/Configuration
1. Open NPort Search Utility and then click the Search icon.
The Searching window indicates the progress of the search.
7-15
NPort S8000 Series
Software Installation/Configuration
2. When the search is complete, all NPort S8000 servers that were located will be displayed in the NPort
Search Utility window.
3. To modify the configuration of the highlighted NPort S8000, click on the Console icon to open the web
console. This will take you to the web console, where you can make all configuration changes. Please refer
to Chapter 5, Configuration with the Web Console, for information on how to use the web console.
Linux Real TTY Drivers
Basic Procedures
To map an NPort S8000 serial port to a Linux host’s tty port, follow these instructions:
1. Set up the NPort S8000. After verifying that the IP configuration works and you can access the NPort S8000
(by using ping, telnet, etc.), configure the desired serial port on the NPort S8000 to Real COM mode.
2. Install the Linux Real tty driver files on the host
3. Map the NPort serial port to the host’s tty port
Hardware Setup
Before proceeding with the software installation, make sure you have completed the hardware installation.
Note that the default IP address for the NPort S8000 is 192.168.127.254.
NOTE
After installing the hardware, you must configure the operating mode of the serial port on your NPort S8000 to
Real COM mode.
Installing Linux Real TTY Driver Files
1. Obtain the driver file from the included CD-ROM or the Moxa website, at http://www.moxa.com.
2. Log in to the console as a super user (root).
7-16
NPort S8000 Series
Software Installation/Configuration
3. Execute cd / to go to the root directory.
4. Copy the driver file npreal2xx.tgz to the
/ directory.
5. Execute tar xvfz npreal2xx.tgz to extract all files into the system.
6. Execute /tmp/moxa/mxinst.
For RedHat AS/ES/WS and Fedora Core1, append an extra argument as follows:
# /tmp/moxa/mxinst SP1
The shell script will install the driver files automatically.
7. After installing the driver, you will be able to see several files in the /usr/lib/npreal2/driver folder:
> mxaddsvr
(Add Server, mapping tty port)
> mxdelsvr
(Delete Server, un-mapping tty port)
> mxloadsvr
(Reload Server)
> mxmknod
(Create device node/tty port)
> mxrmnod
(Remove device node/tty port)
> mxuninst
(Remove tty port and driver files)
At this point, you will be ready to map the NPort serial port to the system tty port.
Mapping TTY Ports
Make sure that you set the operation mode of the desired NPort S8000 serial port to Real COM mode. After
logging in as a super user, enter the directory /usr/lib/npreal2/driver and then execute mxaddsvr to map
the target NPort serial port to the host tty ports. The syntax of mxaddsvr is as follows:
mxaddsvr [NPort IP Address] [Total Ports] ([Data port] [Cmd port])
The mxaddsvr command performs the following actions:
1. Modifies npreal2d.cf.
2. Creates tty ports in directory /dev with major & minor number configured in npreal2d.cf.
3. Restarts the driver.
Mapping tty ports automatically
To map tty ports automatically, you may execute mxaddsvr with just the IP address and number of ports, as
in the following example:
# cd /usr/lib/npreal2/driver
# ./mxaddsvr 192.168.3.4 16
In this example, 16 tty ports will be added, all with IP 192.168.3.4, with data ports from 950 to 965and
command ports from 966 to 981.
Mapping tty ports manually
To map tty ports manually, you may execute mxaddsvr and manually specify the data and command ports, as
in the following example:
# cd /usr/lib/npreal2/driver
# ./mxaddsvr 192.168.3.4 16 4001 966
In this example, 16 tty ports will be added, all with IP 192.168.3.4, with data ports from 4001 to 4016 and
command ports from 966 to 981.
Removing Mapped TTY Ports
After logging in as root, enter the directory /usr/lib/npreal2/driver and then execute mxdelsvr to delete
a server. The syntax of mxdelsvr is:
mxdelsvr [IP Address]
7-17
NPort S8000 Series
Software Installation/Configuration
Example:
# cd /usr/lib/npreal2/driver
# ./mxdelsvr 192.168.3.4
The following actions are performed when executing mxdelsvr:
1. Modify npreal2d.cf.
2. Remove the relevant tty ports in directory /dev.
3. Restart the driver.
If the IP address is not provided in the command line, the program will list the installed servers and total ports
on the screen. You will need to choose a server from the list for deletion.
Removing Linux Driver Files
A utility is included that will remove all driver files, mapped tty ports, and unload the driver. To do this, you only
need to enter the directory /usr/lib/npreal2/driver, then execute mxuninst to uninstall the driver. This
program will perform the following actions:
1. Unload the driver.
2. Delete all files and directories in /usr/lib/npreal2
3. Delete directory /usr/lib/npreal2
4. Modify the system initializing script file.
The UNIX Fixed TTY Driver
Installing the UNIX Driver
1. Log in to UNIX and create a directory for the Moxa TTY. To create a directory named /usr/etc, execute the
command:
# mkdir –p /usr/etc
2. Copy moxattyd.tar to the directory you created. If you created the /usr/etc directory above, you would
execute the following commands:
# cp moxattyd.tar /usr/etc
# cd /usr/etc
3. Extract the source files from the tar file by executing the command:
# tar xvf moxattyd.tar
The following files will be extracted:
README.TXT
moxattyd.c
--- source code
moxattyd.cf
--- an empty configuration file
Makefile
VERSION.TXT
--- makefile
--- fixed tty driver version
FAQ.TXT
4. Compile and Link
For SCO UNIX:
# make sco
For UnixWare 7:
# make svr5
For UnixWare 2.1.x, SVR4.2:
# make svr42
7-18
NPort S8000 Series
Software Installation/Configuration
Configuring the UNIX Driver
Modify the configuration:
The configuration used by the moxattyd program is defined in the text file moxattyd.cf, which is in the same
directory that contains the program moxattyd. You may use vi, or any text editor to modify the file, as follows:
ttyp1 192.168.1.1 950
For more configuration information, view the file moxattyd.cf, which contains detailed descriptions of the
various configuration parameters.
NOTE
The “Device Name” depends on the OS. See the Device Naming Rule section in README.TXT for more
information.
To start the moxattyd daemon after system bootup, add an entry into /etc/inittab, with the tty name you
configured in moxattyd.cf, as in the following example:
ts:2:respawn:/usr/etc/moxattyd/moxattyd –t 1
Device naming rule
For UnixWare 7, UnixWare 2.1.x, and SVR4.2, use:
pts/[n]
For all other UNIX operating systems, use:
ttyp[n]
Starting moxattyd
Execute the command init q or reboot your UNIX operating system.
Adding an additional server
1. Modify the text file moxattyd.cf to add an additional server. User may use vi or any text editor to modify
the file. For more configuration information, look at the file moxattyd.cf, which contains detailed
descriptions of the various configuration parameters.
2. Find the process ID (PID) of the program moxattyd.
# ps -ef | grep moxattyd
3. Update configuration of moxattyd program.
# kill -USR1 [PID]
(e.g., if moxattyd PID = 404, kill -USR1 404)
This completes the process of adding an additional server.
7-19
A
A.
Pinouts and Cable Wiring
In this appendix, we cover the following topics.
 Port Pinout Diagrams
 Ethernet Port Pinouts
 Serial Port Pinouts
 Cable Wiring Diagrams
 Ethernet Cables
NPort S8000 Series
Pinouts and Cable Wiring
Port Pinout Diagrams
Ethernet Port Pinouts
Pin
Signal
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Serial Port Pinouts
DB9 Male RS-232 Port Pinouts
Pin
RS-232 Signal
1
DCD (in)
2
RxD (in)
3
TxD (out)
4
DTR (out)
5
GND
6
DSR (in)
7
RTS (out)
8
CTS (in)
9
---
Cable Wiring Diagrams
Ethernet Cables
A-2
B
B.
Well Known Port Numbers
This appendix is for your reference about the Well Known port numbers that may cause network problem if you
set the NPort into the same port. Refer to RFC 1700 for Well Known port numbers of refer to the following
introduction from the IANA.
The port numbers are divided into three ranges: the Well Known Ports, the Registered Ports, and the Dynamic
and/or Private Ports.
The Well Known Ports are those from 0 through 1023.
The Registered Ports are those from 1024 through 49151.
The Dynamic and/or Private Ports are those from 49152 through 65535.
The Well Known Ports are assigned by the IANA, and on most systems, can only be used by system processes
or by programs executed by privileged users. The following table shows famous port numbers among the
well-known port numbers. For more details, please visit the IANA website:
http://www.iana.org/assignments/port-numbers
UDP Socket
Application Service
0
reserved
2
Management Utility
7
Echo
9
Discard
11
Active Users (systat)
13
Daytime
35
Any private printer server
39
Resource Location Protocol
42
Host name server (names server)
43
Whois (nickname)
49
(Login Host Protocol) (Login)
53
Domain Name Server (domain)
69
Trivial Transfer Protocol (TETP)
70
Gopler Protocol
79
Finger Protocol
80
World Wide Web HTTP
107
Remote Telnet Service
111
Sun Remote Procedure Call (Sunrpc)
119
Network News Transfer Protocol (NNTP)
123
Network Time Protocol (nnp)
161
SNMP (Simple Network Mail Protocol)
162
SNMP Traps
213
IPX (Used for IP Tunneling)
NPort S8000 Series
Well Known Port Numbers
TCP Socket
Application Service
0
reserved
1
TCP Port Service Multiplexor
2
Management Utility
7
Echo
9
Discard
11
Active Users (systat)
13
Daytime
15
Netstat
20
FTP data port
21
FTP CONTROL port
23
Telnet
25
SMTP (Simple Mail Transfer Protocol)
37
Time (Time Server)
42
Host name server (names server)
43
Whois (nickname)
49
(Login Host Protocol) (Login)
TCP Socket
Application Service
53
Domain Name Server (domain)
79
Finger protocol (Finger)
80
World Wide Web HTTP
119
Network News Transfer Protocol (NNTP)
123
Network Time Protocol
213
IPX
160 – 223
Reserved for future use
B-2
C
C.
SNMP Agents with MIB II & RS-232 Like
Groups
The NPort S8000 has built-in SNMP (Simple Network Management Protocol) agent software. The following table
lists the proprietary MIB-II group, as well as the variable implementation for the NPort S8000.
Moxa-NPort S8000-MIB
overview
basicSetting
portSetting
ethernetSetting
ModelName
generalSettings
opModeSetting
portSettings
SerialNumber
serverName
opMode
portTable
FirmwareVersion
serverLocation
opModePortTable
portEntry
MacAddress
serverDescription
opModePortEntry
portIndex_Eth
Uptime
maintainerContactInfo
portIndex
portEnable
ViewIpAddr
timeSetting
portMode
portDesc
sysDateTime
application
portName
daylightSaving
realcom
portSpeed
startMonth
realComTable
portFDXFlowCtrl
startWeek
realComEntry
portMDI
startDay
realcomMaxConnection
startHour
realcomAllowDriverControl
portTrunking
endMonth
realcomConnectionDownRTS
trunkSettingTable
endWeek
realcomConnectionDownDTR
trunkSettingEntry
endDay
rfc2217
trunkSettingIndex
endHour
rfc2217Table
trunkType
offsetHours
rfc2217Entry
trunkMemberPorts
timeZone
rfc2217TcpPort
timeServer1
tcpServer
commRedundancy
timeServer2
tcpServerTable
protocolOfRedundancySetup
calibratePeriod
tcpServerEntry
spanningTree
networkSettings
tcpServerInactivityTime
spanningTreeBridgePriority
autoIPConfig
tcpServerMaxConnection
spanningTreeHelloTime
serverIpAddr
tcpServerAllowDriverControl
spanningTreeMaxAge
subMask
tcpServerTcpServerConnectionD spanningTreeForwardingDelay
gateway
tcpServerTcpServerConnectionD spanningTreeTable
ownRTS
ownDTR
dnsServer1IPAddr
tcpServerTcpPort
spanningTreeEntry
dnsServer2IPAddr
tcpServerCmdPort
spanningTreeIndex
tcpAliveChkTime
tcpClient
enableSpanningTree
tcpClientTable
spanningTreePortPriority
tcpClientEntry
spanningTreePortCost
tcpClientInactivityTime
turboRing
tcpClientDestinationAddress1
turboRingMasterSetup
tcpClientDestinationPort1
turboRingRdntPort1
NPort S8000 Series
overview
SNMP Agents with MIB II & RS-232 Like Group
basicSetting
portSetting
ethernetSetting
tcpClientDestinationAddress2
turboRingRdntPort2
tcpClientDestinationPort2
turboRingEnableCoupling
tcpClientDestinationAddress3
turboRingCouplingPort
tcpClientDestinationPort3
turboRingControlPort
tcpClientDestinationAddress4
turboRingV2
tcpClientDestinationPort4
turboRingV2Ring1
tcpClientDesignatedLocalPort1
ringIndexRing1
tcpClientDesignatedLocalPort2
ringEnableRing1
tcpClientDesignatedLocalPort3
masterSetupRing1
tcpClientDesignatedLocalPort4
rdnt1stPortRing1
tcpClientConnectionControl
rdnt2ndPortRing1
udp
turboRingV2Ring2
udpTable
ringIndexRing2
udpEntry
ringEnableRing2
udpDestinationAddress1Begin
masterSetupRing2
udpDestinationAddress1End
rdnt1stPortRing2
udpDestinationPort1
rdnt2ndPortRing2
udpDestinationAddress2Begin
turboRingV2Coupling
udpDestinationAddress2End
couplingEnable
udpDestinationPort2
couplingMode
udpDestinationAddress3Begin
coupling1stPort
udpDestinationAddress3End
coupling2ndPort
udpDestinationPort3
udpDestinationAddress4Begin
rateLimiting
udpDestinationAddress4End
rateLimitingTable
udpDestinationPort4
rateLimitingEntry
udpLocalListenPort
limitMode
dataPacking
lowPriLimitRate
dataPackingPortTable
normalPriLimitRate
dataPackingPortEntry
mediumPriLimitRate
portPacketLength
highPriLimitRate
portDelimiter1Enable
portDelimiter1
lineSwapFastRecovery
portDelimiter2Enable
lineSwapRecovery
portDelimiter2
portDelimiterProcess
portForceTransmit
comParamSetting
comParamPortTable
comParamPortEntry
portAlias
portBaudRate
portDataBits
portStopBits
portParity
portFlowControl
portFIFO
portInterface
portBaudRateManual
serialTosSetting
C-2
NPort S8000 Series
overview
SNMP Agents with MIB II & RS-232 Like Group
basicSetting
portSetting
serialTosTable
serialTosEntry
ethernetAdvSetting
systemManagement
trafficPrioritization
miscNetwork
qosClassification
accessibleIP
queuingMechanism
enableAccessibleIP
qosPortTable
accessibleIpEntry
qosPortEntry
accessibleIpIndex
inspectTos
accessibleIpAddress
inspectCos
accessibleIpNetMask
portPriority
syslogSetting
cosMapping
syslogServer1
cosMappingTable
syslogServer1port
cosMappingEntry
syslogServer2
cosTag
syslogServer2port
cosMappedPriority
syslogServer3
tosMapping
syslogServer3port
tosMappingTable
portAccessControl
tosMappingEntry
staticPortLock
tosClass
staticPortLockAddress
tosMappedPriority
staticPortLockPort
vlan
staticPortLockStatus
vlanType
dot1x
managementVlanId
dataBaseOption
vlanPortSettingTable
radiusServer
vlanPortSettingEntry
radiusPort
portVlanType
radiusSharedKey
portDefaultVid
dot1xReauthEnable
portFixedVid
dot1xReauthPeriod
portForbiddenVid
dot1xSettingTable
portbaseVlanSettingEntry
dot1xSettingEntry
portbaseVlanSettingIndex
enableDot1X
portbaseVlanMemberPorts
autoWarming
multicastFiltering
emailAlert
igmpSnooping
emailWarningMailServer
enableGlobalIgmpSnooping
emailWarningFromEmail
querierQueryInterval
emailWarningFirstEmailAddr
igmpSnoopingSettingTable
emailWarningSecondEmailAddr
igmpSnoopingSettingEntry
emailWarningThirdEmailAddr
enableIgmpSnooping
emailWarningFourthEmailAddr
enableQuerier
snmpAgent
fixedMulticastQuerierPorts
snmpReadCommunity
staticMulticast
trapServerAddr1
staticMulticastTable
snmpTrapCommunity1
staticMulticastEntry
trap2ServerAddr
staticMulticastIndex
snmpTrap2Community
staticMulticastAddress
emailWarningEventType
staticMulticastPorts
emailWarningEventServerColdStart
staticMulticastStatus
emailWarningEventServerWarmStart
gmrp
emailWarningEventPowerOn2Off
C-3
ethernetSetting
NPort S8000 Series
SNMP Agents with MIB II & RS-232 Like Group
ethernetAdvSetting
systemManagement
gmrpSettingTable
emailWarningEventPowerOff2On
gmrpSettingEntry
emailWarningEventDiTable
enableGMRP
emailWarningEventDiEntry
setDeviceIp
emailWarningEventDiInputOn2Off
setDevIpTable
emailWarningEventDiInputOff2On
setDevIpEntry
emailWarningEventConfigChange
setDevIpIndex
emailWarningEventAuthFail
setDevIpCurrentIpofDevice
emailWarningEventTopologyChanged
setDevIpPresentBy
emailWarningEventSerialPortTable
setDevIpDedicatedIp
emailWarningEventSerialPortEntry
emailWarningEventSerailDCDChange
emailWarningEventSerailDSRChange
emailWarningEventEthernetPortTable
emailWarningEventEthernetPortEntry
emailWarningEventEthernetPortLinkOn
emailWarningEventEthernetPortLinkOff
emailWarningEventEthernetPortTrafficOverload
emailWarningEventEthernetPortTrafficThreshold
emailWarningEventEthernetPortTrafficDuration
snmpWarningEventType
snmpWarningEventServerColdStart
snmpWarningEventServerWarmStart
snmpWarningEventPowerOn2Off
snmpWarningEventPowerOff2On
snmpWarningEventDiTable
snmpWarningEventDiEntry
snmpWarningEventDiInputOn2Off
snmpWarningEventDiInputOff2On
snmpWarningEventConfigChange
snmpWarningEventAuthFail
snmpWarningEventTopologyChanged
snmpWarningEventSerailPortTable
snmpWarningEventSerailPortEntry
snmpWarningEventSerailDCDchange
snmpWarningEventSerailDSRchange
snmpWarningEventEthernetPortTable
snmpWarningEventEthernetPortEntry
snmpWarningEventEthernetPortLinkOn
snmpWarningEventEthernetPortLinkOff
snmpWarningEventEthernetPortTrafficOverload
snmpWarningEventEthernetPortTrafficThreshold
snmpWarningEventEthernetPortTrafficDuration
relayWarning
relayWarningTable
relayWarningEntry
relayAlarmIndex
relayWarningRelayContact
overrideRelayWarningSetting
relayWarningPower1Off
relayWarningPower1OffStatus
relayWarningPower2Off
relayWarningPower2OffStatus
C-4
NPort S8000 Series
ethernetAdvSetting
SNMP Agents with MIB II & RS-232 Like Group
systemManagement
relayWarningTurboRingBreak
relayWarningTurboRingBreakStatus
portRelayWarningTable
portRelayWarningEntry
relayWarningLinkChanged
relayWarningLinkChangedStatus
relayWarningTrafficOverload
relayWarningTrafficOverloadStatus
relayWarningTrafficThreshold
relayWarningTrafficDuration
diRelayWarningTable
diRelayWarningEntry
relayWarningDiInputChanged
relayWarningDiInputChangedStatus
sysLogSettings
sysLocalLog
networkLocalLog
configLocalLog
opModeLocalLog
sysRemoteLog
networkRemoteLog
configRemoteLog
opModeRemoteLog
maintenance
consoleSetting
webConsole
httpConsole
telnetConsole
resetButtonFunction
autoRefresh
loadFactoryDefault
loadFactoryDefaultSetting
mirroring
targetPort
monitorDirection
mirroringPort
sysFileUpdate
tftpServer
confPathName
firmwarePathName
logPathName
dipSwitchSetting
dipSwitchEnableTurboRing
dipSwitchTurboRingType
systemMonitoring
restart
serialStatus
restartSystem
s2eConnections
restartPortNumber
monitorRemoteIpTable
monitorRemoteIpEntry
remoteIpIndex
monitorRemoteIp
C-5
NPort S8000 Series
systemMonitoring
SNMP Agents with MIB II & RS-232 Like Group
restart
serialPortStatus
monitorSerialPortStatusTable
monitorSerialPortStatusEntry
monitorTxCount
monitorRxCount
monitorTxTotalCount
monitorRxTotalCount
monitorDSR
monitorDTR
monitorRTS
monitorCTS
monitorDCD
serialPortErrorCount
monitorSerialPortErrorCountTable
monitorSerialPortErrorCountEntry
monitorErrorCountFrame
monitorErrorCountParity
monitorErrorCountOverrun
monitorErrorCountBreak
serialPortSettings
monitorSerialPortSettingsTable
monitorSerialPortSettingsEntry
monitorBaudRate
monitorDataBits
monitorStopBits
monitorParity
monitorRTSCTSFlowControl
monitorXONXOFFFlowControl
monitorFIFO
monitorInterface
systemStatus
systemInfo
power1InputStatus
power2InputStatus
monitorDiTable
monitorDiEntry
diIndex
diInputStatus
dipSwitchTurboRingPole
dipSwitchRingCouplingPole
dipSwitchRingMasterPole
eventLog
eventLogTable
eventLogEntry
eventListIndex
eventListBootup
eventListData
eventListTime
eventListSysUpTime
eventListEvent
eventListClear
ethernetStatus
C-6
NPort S8000 Series
systemMonitoring
SNMP Agents with MIB II & RS-232 Like Group
restart
macAddressList
igmpstatus
igmpSnoopingMulticastGroupTable
igmpSnoopingMulticastGroupEntry
learnedMulticastQuerierPorts
igmpSnoopingIpGroup
igmpSnoopingMacGroup
igmpSnoopingJoinedPorts
gmrpStatus
gmrpTable
gmrpEntry
gmrpMulticastGroup
gmrpFixedPorts
gmrpLearnedPorts
dot1XReauth
dot1xReauthTable
dot1xReauthEntry
dot1xReauthPortIndex
dot1xReauth
portAccessControlList
portAccessControlTable
portAccessControlEntry
portAccessControlAddress
portAccessControlPortNo
portAccessControlAccessStatus
portAccessControlStatus
warningList
warningListTable
warningListEntry
warningListIndex
warningListEvent
warningListRelay
ethernetMonitor
ethernetMonitorTable
ethernetMonitorEntry
ethernetMonitorTxTotal
ethernetMonitorTxUicast
ethernetMonitorTxMulticast
ethernetMonitorTxBroadcast
ethernetMonitorTxCollision
ethernetMonitorRxTotal
ethernetMonitorRxUicast
ethernetMonitorRxMulticast
ethernetMonitorRxBroadcast
ethernetMonitorRxPause
ethernetMonitorTxErr
ethernetMonitorTxErrLate
ethernetMonitorTxErrExcessive
ethernetMonitorRxErr
ethernetMonitorRxErrCRC
ethernetMonitorRxErrDiscard
ethernetMonitorRxErrUndersize
C-7
NPort S8000 Series
systemMonitoring
SNMP Agents with MIB II & RS-232 Like Group
restart
ethernetMonitorRxErrFragments
ethernetMonitorRxErrOversize
ethernetMonitorRxErrJabber
ethernetMonitorReset
monitorPortTable
monitorPortEntry
monitorLinkStatus
monitorSpeed
monitorFDXFlowCtrl
monitorAutoMDI
monitorConnectedIP
monitorTraffic
trunkTableList
trunkTable
trunkEntry
trunkIndex
trunkPort
trunkStatus
vlanList
vlanTable
vlanEntry
vlanId
joinedAccessPorts
joinedTrunkPorts
commRedStatus
activeProtocolOfRedundancy
spanningTreeStatus
spanningTreeRoot
spanningTreeStatusTable
spanningTreeStatusEntry
spanningTreePortStatus
turboRingStatus
turboRingMaster
turboRingPortTable
turboRingPortEntry
turboRingPortIndex
turboRingPortStatus
turboRingPortDesignatedBridge
turboRingPortDesignatedPort
turboRingDesignatedMaster
turboRingCouplingPortStatus
turboRingControlPortStatus
turboRingBrokenStatus
turboRingV2Status
turboRingV2Ring1Status
masterStatusRing1
designatedMasterRing1
rdnt1stPortStatusRing1
rdnt2ndPortStatusRing1
brokenStatusRing1
turboRingV2Ring2Status
masterStatusRing2
C-8
NPort S8000 Series
systemMonitoring
SNMP Agents with MIB II & RS-232 Like Group
restart
designatedMasterRing2
rdnt1stPortStatusRing2
rdnt2ndPortStatusRing2
brokenStatusRing2
turboRingV2CouplingStatus
coupling1stPortStatus
coupling2ndPortStatus
C-9
D
D.
Switch MIB Groups
The NPort S8000 comes with built-in SNMP (Simple Network Management Protocol) agent software that
supports cold/warm start trap, line up/down trap, and RFC 1213 MIB-II.
The standard MIB groups supported by the NPort S8000 are:
MIB II.1 – System Group
sysORTable
MIB II.2 – Interfaces Group
ifTable
MIB II.4 – IP Group
ipAddrTable
ipNetToMediaTable
IpGroup
IpBasicStatsGroup
IpStatsGroup
MIB II.5 – ICMP Group
IcmpGroup
IcmpInputStatus
IcmpOutputStats
MIB II.6 – TCP Group
tcpConnTable
TcpGroup
TcpStats
MIB II.7 – UDP Group
udpTable
UdpStats
MIB II.10 – Transmission Group
dot3
dot3StatsTable
MIB II.11 – SNMP Group
SnmpBasicGroup
SnmpInputStats
SnmpOutputStats
MIB II.17 – dot1dBridge Group
dot1dBase
dot1dBasePortTable
dot1dStp
dot1dStpPortTable
dot1dTp
dot1dTpFdbTable
dot1dTpPortTable
NPort S8000 Series
Switch MIB Groups
dot1dTpHCPortTable
dot1dTpPortOverflowTable
pBridgeMIB
dot1dExtBase
dot1dPriority
dot1dGarp
qBridgeMIB
dot1qBase
dot1qTp
dot1qFdbTable
dot1qTpPortTable
dot1qTpGroupTable
dot1qForwardUnregisteredTable
dot1qStatic
dot1qStaticUnicastTable
dot1qStaticMulticastTable
dot1qVlan
dot1qVlanCurrentTable
dot1qVlanStaticTable
dot1qPortVlanTable
The NPort S8000 also provides a private MIB file, located in the file “Moxa-NPort S8000-MIB.my” or
“Moxa-NPort S8000-MIB.my” on the NPort S8000 Series utility CD-ROM.
Public Traps:
1. Cold Start
2. Link Up
3. Link Down
4. Authentication Failure
5. dot1dBridge New Root
6. dot1dBridge Topology Changed
Private Traps:
1. Configuration Changed
2. Power On
3. Power Off
4. Traffic Overloaded
5. Turbo Ring Topology Changed
6. Turbo Ring Coupling Port Changed
7. Turbo Ring Master Mismatch
System Events
1. System cold start
2. System warm start
3. Power transition(On->Off
4. Power transition(Off->On)
5. DI 1 (Off)
6. DI 1 (On)
7. DI 2 (Off)
8. DI 2 (On)
9. Config. change
10. Auth. failure
11. Comm. redundancy topology changed
D-2
NPort S8000 Series
Switch MIB Groups
Serial Port Events
1. DCD changed
2. DSR changed
Ethernet Port Events
1. Link-ON
2. Link-OFF
3. Traffic-Overload
4. Traffic-Threshold(%)
5. Traffic-Duration(s)
D-3
E
E.
Compliance Note
This product complies with Chinese RoHS (Restriction of Hazardous Substances)
regulations for Electronic Information Products.
CE Warming
This is a Class A product. In a domestic environment, this product may cause radio interference in which case
the user may be required to take appropriate measures.
Federal Communications Commission Statement
FCC – This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Warming
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense.
F
F.
Modbus/TCP Map
EDS-505A Modbus information v1.0
Read Only Registers (Support Function Code 4); 1 Word = 2 bytes.
Address
Data Type
Description
0x0000
1 word
Vendor ID = 0x1393
0x0001
1 word
Unit ID (Ethernet = 1)
0x0002
1 word
Product Code = 0x0004
0x0010
20 words
Vendor Name = “Moxa”
System Information
Word 0 Hi byte = ‘M’
Word 0 Lo byte = ‘o’
Word 1 Hi byte = ‘x’
Word 1 Lo byte = ‘a’
Word 2 Hi byte = ‘\0’
Word 2 Lo byte = ‘\0’
0x0030
20 word
Product Name = “EDS-505A”
Word 0 Hi byte = ‘E’
Word 0 Lo byte = ‘D’
Word 1 Hi byte = ‘S’
Word 1 Lo byte = ‘-’
Word 2 Hi byte = ‘5’
Word 2 Lo byte = ‘0’
Word 3 Hi byte = ‘5’
Word 3 Lo byte = ‘A’
Word 4 Hi byte = ‘\0’
Word 4 Lo byte = ‘\0’
0x0050
1 word
Product Serial Number
0x0051
2 word
Firmware Version
Word 0 Hi byte = major (A)
Word 0 Lo byte = minor (B)
Word 1 Hi byte = release (C)
Word 1 Lo byte = build (D)
0x0053
2 word
Firmware Release Date
Firmware was released on 2007-05-06 at 09 o’clock
Word 0 = 0x0609
Word 1 = 0x0705
0x0055
3 word
Ethernet MAC Address
Ex:
MAC = 00-01-02-03-04-05
Word 0 Hi byte = 0x00
Word 0 Lo byte = 0x01
Word 1 Hi byte = 0x02
Word 1 Lo byte = 0x03
Word 2 Hi byte = 0x04
Word 2 Lo byte = 0x05
NPort S8000 Series
0x0058
Compliance Note
1 word
Power 1
0x0000: Off
0x0001: On
0x0059
1 word
Power 2
0x0000: Off
0x0001: On
0x005A
1 word
Fault LED Status
0x0000: No
0x0001: Yes
0x0080
1 word
DI1
0x0000: Off
0x0001: On
0x0081
1 word
DI2
0x0000: Off
0x0001: On
0x0082
1 word
DO1
0x0000: Off
0x0001: On
0x0083
1 word
DO2
0x0000: Off
0x0001: On
Port Information
0x1000 to 0x1011
1 word
Port 1 to 5 Status
0x0000: Link down
0x0001: Link up
0x0002: Disable
0xFFFF: No port
0x1100 to 0x1111
1 word
Port 1 to 5 Speed
0x0000: 10M-Half
0x0001: 10M-Full
0x0002: 100M-Half
0x0003: 100M-Full
0x0004: 1G-Half
0x0005: 1G- Full
0xFFFF: No port
0x1200 to 0x1211
1 word
Port 1 to 5 Flow Ctrl
0x0000: Off
0x0001: On
0xFFFF: No port
0x1300 to 0x1311
1 word
Port 1 to 5 MDI/MDIX
0x0000: MDI
0x0001: MDIX
0xFFFF: No port
E-2
NPort S8000 Series
0x1400 to 0x1413(Port
Compliance Note
20 word
Port 1 to 5 Description
1)
Port Description = “100TX,RJ45.”
0x1414 to 0x1427(Port
Word 0 Hi byte = ‘1’
2)
Word 0 Lo byte = ‘0’
Word 1 Hi byte = ‘0’
Word 1 Lo byte = ‘T’
…
Word 4 Hi byte = ‘4’
Word 4 Lo byte = ‘5’
Word 5 Hi byte = ‘.’
Word 5 Lo byte = ‘\0’
Packets Information
0x2000 to 0x2023
2 word
Port 1 to 5 Tx Packets
Ex: port 1 Tx Packets = 0x44332211
Word 0 = 4433
Word 1 = 2211
0x2100 to 0x2123
2 word
Port 1 to 5 Rx Packets
Ex: port 1 Rx Packets = 0x44332211
Word 0 = 4433
Word 1 = 2211
0x2200 to 0x2223
2 word
port 1 to 5 Tx Error Packets
Ex: port 1 Tx Error Packets = 0x44332211
Word 0 = 4433
Word 1 = 2211
0x2300 to 0x2323
2 word
port 1 to 5 Rx Error Packets
Ex: port 1 Rx Error Packets = 0x44332211
Word 0 = 4433
Word 1 = 2211
Redundancy Information
0x3000
1 word
Redundancy Protocol
0x0000: None
0x0001: RSTP
0x0002: Turbo Ring
0x0003: Turbo Ring V2
0x0004: Turbo Chain
0x3100
1 word
RSTP Root
0x0000: Not Root
0x0001: Root
0xFFFF: RSTP Not Enable
0x3200 to 0x3211
1 word
RSTP Port 1 to 5 Status
0x0000: Port Disabled
0x0001: Not RSTP Port
0x0002: Link Down
0x0003: Blocked
0x0004: Learning
0x0005: Forwarding
0xFFFF: RSTP Not Enable
0x3300
1 word
TR Master/Slave
0x0000: Slave
0x0001: Master
0xFFFF: Turbo Ring Not Enable
E-3
NPort S8000 Series
0x3301
Compliance Note
1 word
TR 1st Port status
0x0000: Port Disabled
0x0001: Not Redundant
0x0002: Link Down
0x0003: Blocked
0x0004: Learning
0x0005: Forwarding
0x3302
1 word
TR 2nd Port status
0x0000: Port Disabled
0x0001: Not Redundant
0x0002: Link Down
0x0003: Blocked
0x0004: Learning
0x0005: Forwarding
0x3303
1 word
TR Coupling
0x0000: Off
0x0001: On
0xFFFF: Turbo Ring Not Enable
0x3304
1 word
TR Coupling Port status
0x0000: Port Disabled
0x0001: Not Coupling Port
0x0002: Link Down
0x0003: Blocked
0x0005: Forwarding
0xFFFF: Turbo Ring Not Enable
0x3305
1 word
TR Coupling Control Port status
0x0000: Port Disabled
0x0001: Not Coupling Port
0x0002: Link Down
0x0003: Blocked
0x0005: Forwarding
0x0006: Inactive
0x0007: Active
0xFFFF: Turbo Ring Not Enable
0x3500
1 word
TR2 Coupling Mode
0x0000: None
0x0001: Dual Homing
0x0002: Coupling Backup
0x0003: Coupling Primary
0xFFFF: Turbo Ring V2 Not Enable
0x3501
1 word
TR2 Coupling Port Primary status
(Using in Dual Homing, Coupling Backup, Coupling
Primary)
0x0000: Port Disabled
0x0001: Not Coupling Port
0x0002: Link Down
0x0003: Blocked
0x0004: Learning
0x0005: Forwarding
0xFFFF: Turbo Ring V2 Not Enable
E-4
NPort S8000 Series
0x3502
Compliance Note
1 word
TR2 Coupling Port Backup status
(Only using in Dual Homing)
0x0000: Port Disabled
0x0001: Not Coupling Port
0x0002: Link Down
0x0003: Blocked
0x0004: Learning
0x0005: Forwarding
0xFFFF: Turbo Ring V2 Not Enable
0x3600
1 word
TR2 Ring 1 status
0x0000: Healthy
0x0001: Break
0xFFFF: Turbo Ring V2 Not Enable
0x3601
1 word
TR2 Ring 1 Master/Slave
0x0000: Slave
0x0001: Master
0xFFFF: Turbo Ring V2 Ring 1 Not Enable
0x3602
1 word
TR2 Ring 1 1st Port status
0x0000: Port Disabled
0x0001: Not Redundant
0x0002: Link Down
0x0003: Blocked
0x0004: Learning
0x0005: Forwarding
0xFFFF: Turbo Ring V2 Ring 1 Not Enable
0x3603
1 word
TR2 Ring 1 2nd Port status
0x0000: Port Disabled
0x0001: Not Redundant
0x0002: Link Down
0x0003: Blocked
0x0004: Learning
0x0005: Forwarding
0xFFFF: Turbo Ring V2 Ring 1 Not Enable
0x3680
1 word
TR2 Ring 2 status
0x0000: Healthy
0x0001: Break
0xFFFF: Turbo Ring V2 Ring 2 Not Enable
0x3681
1 word
TR2 Ring 2 Master/Slave
0x0000: Slave
0x0001: Master
0xFFFF: Turbo Ring V2 Ring 2 Not Enable
0x3682
1 word
TR2 Ring 2 1st Port status
0x0000: Port Disabled
0x0001: Not Redundant
0x0002: Link Down
0x0003: Blocked
0x0004: Learning
0x0005: Forwarding
0xFFFF: Turbo Ring V2 Ring 2 Not Enable
E-5
NPort S8000 Series
0x3683
Compliance Note
1 word
TR2 Ring 2 2nd Port status
0x0000: Port Disabled
0x0001: Not Redundant
0x0002: Link Down
0x0003: Blocked
0x0004: Learning
0x0005: Forwarding
0xFFFF: Turbo Ring V2 Ring 2 Not Enable
0x3700
1 word
Turbo Chain Switch Role
0x0000: Head
0x0001: Member
0x0002: Tail
0xFFFF: Turbo Chain Not Enable
0x3701
1 word
Turbo Chain 1st Port status
0x0000: Link Down
0x0001: Blocking
0x0002: Blocked
0x0003: Forwarding
0xFFFF: Turbo Ring V2 Ring 2 Not Enable
0x3702
1 word
Turbo Chain 2nd Port status
0x0000: Link Down
0x0001: Blocking
0x0002: Blocked
0x0003: Forwarding
0xFFFF: Turbo Ring V2 Ring 2 Not Enable
Memory mapping from address 0x0000 to 0x3FFF.
E-6