PR XLed 3019 LED Movinghead Owner's Manual

XLED 3019

PR-8127

This product manual contains important information about the safe installation and use of this projector.

Please read and follow these instructions carefully and keep this manual in a safe place for future reference.

PR LIGHTING LTD. http://www.pr-lighting.com

INDEX

SAFE USAGE OF THE PROJECTOR……………………………………………………………………………..... 3

INSTALLING THE PROJECTOR…………………………………………………………………………………... 4

POWER SUPPLY – MAINS………………………………………………………………………………………… 4

CONTROL CONNECTIONS……………………………………………………………………………………….. 5

DMX TERMINATOR………………………………………………………………………………………………. 5

SETUP OPTIONS-PROJECTOR CONFIGURATION……………………………………………………………… 6

TO SET THE DMX START ADDRESS…………………………………………………………………………….. 6

OPERATION MENU………………………………………………………………………………………………... 7

DMX PROTOCOL………………………………………………………………………………………………….. 9

INDICATION OF LED DIGITAL TUBE……………………………………………………………………………. 10

MAINTENANCE……………………………………………………………………………………………………. 10

KEEPING THE PROJECTOR CLEAN……………………………………………………………………………… 10

TROUBLESHOOTING……………………………………………………………………………………………… 10

TECHNICAL DATA………………………………………………………………………………………………… 11

ELECTRICAL DIAGRAM………………………………………………………………………………………….. 13

COMPONENT ORDER CODES……………………………………………………………………………………. 14

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer and

/ or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit

G clamp

Ω clamp

XLR cable

Safety cord

User’s manual

2

2

1

1

1

Pcs

Pcs

Pc

Pc

Pc

Wireless Receiver’s Antenna 1 pc

Remark

Optional

With Plug & Socket

Mounted with a projector via its interface before use

2/16

check there is no transportation damage before using the projector. Should there ice away from rain and moisture, excessive heat,

The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure that no ventilation slots are blocked.

Do not project the beam onto inflammable surfaces, minimum dist 5m

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector. relevant standards. cord come into contact with other cables.

The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it should be attached as

Shields and lens shall be changed if they have become visibly damaged to such an extent than their effectiveness is impaired, for example by cracks or deep scratches.

Exterior surface temperatures of the projector

℃

, removed.

Always disconnect a projector when not in use or before cleaning or any maintenance work!

3/16

EXTENSIBLE HANDLE

INSTALL THE PROJECTOR

CLAMP

SAFETY CORD

SAFETY CORD HOLE

!

WARNING

SAFETY CORD GO THROUGH

THE HOLE FOR SAFETY

Take 2 clamps and 1 safety cord out from the package and mount 2 clamps on the underside of projector with 2 retainers attached to each clamp. Hang the projector on the structure and fasten the screws attached to each clamp. (See the WARNING on the underside of the base as shown above) Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning.

Always ensure that the structure that you are going to mount the projector is secure and is strong enough to support a weight of each projector.

WARNING:

1.

The projector MUST be lifted or carried by the HANDLES instead of clamps.

2.

For safety the safety cord should afford 10 times of the unit’s weight.

POWER SUPPLY-MAINS

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector be supplied separately so that they may be individually switched on and off.

IMPORTANT

It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant standards.

4/16

CONTROL CONNECTION

Connection between controller and projector and between one projector and another must be made with a 2 core-screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via cannon 5 pin (which are included with the projector) or 3 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of the plug is not connected in any way. The projector accepts digital control signals in protocol DMX512 (1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown in the figure below.

DMX TERMINATOR

In the Controller mode, at the last projector in the chain, the DMX output has to be connected with a DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120  (ohm) resistor connected across pins 2 and 3, which is then plugged into the output socket on the last projector in the chain. The connections are illustrated below.

5/16

2

120

3

1

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor across pins 2 and 3 in an XLR plug and insert into the DMX out socket on the last unit in the chain.

PIN 2

PIN 3

SETUP OPTIONS-PROJECTOR CONFIGURATION

Projector configuration can be set conveniently via gentle press of button switch and LCD display.

To browse or change its setup options, after button ENTER has been pressed for more than 3 seconds to unlock panel, the

DMX

Address

will be displayed, which means the menus have been entered into.

Press button UP or DOWN to browse or change through the various Setup Options.

Press button ENTER to save your settings or enter the next menu while currently displayed parameters flashing.

Press button UP or DOWN to change values.(Add or subtract)

TO SET THE DMX START ADDRESS

Each projector must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the controller. The projector have two modes of 12CH and 20CH. For example 12CH mode has 12 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 013, No. 3 projector’s address 025, No. 4 projector’s address 037 and so on.

Launch the projector. Press button ENTER more than 3 seconds to unlock the display to enter into menus.

Press button ENTER to display flashing DMX address;

Press button UP and DOWN, you can set the address;

Press button ENTER to confirm it while LED Indication stops from flashing and the projector enters into the upper menu, which means the projector has saved the Start Address .When powered on next time, it will display the value saved last time.

Press button FUNC, it will return to the upper menu .

6/16

OPERATION MENU

1 st

level

DMX Address

Reset

2 nd

level

Standard mode

：

1-501

Extended mode

：

1-493

Are You Sure

Config Setup

3 rd

level

DMX Channel

Mode

Pan Invert

MasterSlaveSelec

Standard 12

Extended 20

No

Yes

Tilt Invert

No

Yes

XLR First

XLR Only

DMX Mode

(Default: XLR first)

Wireless Only

Wireless First

Unlink Wireless

Wireless To XLR

Yes

Slave

Master

Factory Setting

Language Setup

Lcd Dimmer

(Default:10

）

Yes

Chinese

English

1 - 10

4 th

level

Yes

Lcd Light Setup

No

5 th

level Descriptions

Wireless ONLY

Default: Slave

Fixture’s and

Lamp’s hours not cleared

From dark to bright

LCD backlight will be off 3 minutes after the display is locked without any buttons being pressed

Always on

7/16

Information

Test Mode

Operation Mode

Display Inversion

LED Temperature

Fixture’s Time

Software Version

Auto Test

Manual Test

Progra Select

User Progra Edit

No

Yes

XXXX

XXXX

A V.X.X

B V.X.X

C V.X.X

Red

Static Scene

1

～

16

000 - 255

Green

Blue

White

ZOOM

Pan Location

Tilt Location

Preset Memory

User Process

000 - 255

000 - 255

000 - 255

000 - 255

000 - 255

000 - 255

Strobe

Red

Green

Blue

White

ZOOM

Pan Location

Tilt Location

P&T Speed

Keep Time

8/16

Display Inversion

000 - 255

000 - 255

000 - 255

000 - 255

000 - 255

000 - 255

000 - 255

000 - 255

000 - 255

000 - 255

LED temperature

Fixture’s hours

CPU

：

A

、

B

、

C

Software Versions

From dark to bright

From dark to bright

From dark to bright

From dark to bright

Linear Light Spot adjustment

Valid under Master mode

Valid under Master mode

Channel 1’s functions as reference

Linear from dark to bright adjustment

Linear from dark to bright adjustment

Linear from dark to bright adjustment

Linear from dark to bright adjustment

Linear Light Spot adjustment

0*0.1s ~

255*0.1s

Functions

DMX PROTOCOL

DMX Standard Extended Descriptions

1

2

3

4

5

6

7

9

8

10

11

1

2

3

4

13

14

15

16

17

18

7

11

8

12

5

9

6

10

19

Strobe

Dimmer

Color Temp

Color effect

Area 1 Red

Area 2 Red

Area 1 Green

Area 2 Green

Area 1 Blue

Area 2 Blue

Area 1 White

Area 2 White

Zoom

Zoom in 16 bit

Pan

Pan in 16 bit

Tilt

Tilt in 16 Bit

Pan & Tilt

Speeds

000-007 NO Strobe

008-127 Pulse from slow to fast

128-135 NO Strobe

136-177

Pulse Strobe 1

178-185 NO Strobe

186-227 Pulse Strobe 2

228-235 NO Strobe

236-249 Random Strobe

250-255 NO Strobe

000-255 Linear Dimming from dark to Bright

000

001-255

NO

Linear Color Temp adjustment from low to high

（

2700K –

10000K

）

000-007 NO

008-231 32 colors

232-255

Rainbow effect from fast to slow

000-255 Linear adjustment in Red from light to dark of Area 1

000-255 Linear adjustment in Red from light to dark of Area 2

000-255 Linear adjustment in Green from light to dark of Area 1

000-255 Linear adjustment in Green from light to dark of Area 2

000-255 Linear adjustment in Blue from light to dark of Area 1

000-255 Linear adjustment in Blue from light to dark of Area 2

000-255 Linear adjustment in White from light to dark of Area 1

000-255 Linear adjustment in White from light to dark of Area 2

000-255 Linear Zooming (0%~100%)

000-255 Zooming in 16 bit precision

000-255 Pan (0°

～

540°)

000-255 Pan in 16 bit Precision

000-255 Tilt (0°

～

270°)

000-255 Tilt in 16 bit Precision

000-255 Pan and Tilt Speeds from fast to slow

12 20 Control Function

Priority: color effects->single colors-> CT

Note

：

While at rainbow effects, strobe does not work.

000-049 Reserved

050-255 Reset ( Reset after 2 seconds)

9/16

INDICATION OF LED DIGITAL TUBE

Specifications for LED indications

：

On

Green indication

Off

Blue Indication

DMX signal OK

No DMX signal on

Off

Wireless signal OK

Not linked to any transmitter

Flashing Losing link with or being linked with a transmitter

MAINTENANCE

To prolong a Projector’s life, Regular maintenance should be done for its LED optical System to ensure that the system be in best operational condition. If the projector does not function, check the fuses on the power socket of the projector, if burned, they should only be replaced by fuses of the same specification. Should these be damaged call a qualified technician before replacement. The projector has thermal protection device that will switch off the projector in case of overheating, should this occur, check if the fans work normally or fan and fan shield are blocked by dust. If the projector not operational, call a qualified technician. After cleaned and repaired, the projector can be restarted.

Any maintenance work should only be carried out by qualified technicians.

KEEPING THE PROJECTOR CLEAN

It definitely necessary to keep a projector clean for its reliable use. Cooling fans and their shield should be cleaned every 15days. LED lamps’ lens and cover should be cleaned regularly for optimized light output.

Cleaning frequency depends on how often a projector is used and its operational environment. A soft cloth and typical glass cleaning products should be used in cleaning. It is recommended to clean the external optics at least once every 20 days.

Do not use any organic solvent, e.g. alcohol, to clean t housing of the apparatus.

TROUBLESHOOTING

PROBLEM

The projector can’t be started

ACTION



Power Cable not connected well



Power supply damaged or not connected well, a qualified Technician should be required



Control board not connected well and a qualified Technician should be required.

The lamp can be started, but LED lamps are off and not controlled



LED boards not connected properly, a qualified technician is needed

A projector’s lamps are on but it doesn’t respond to the controller



Make sure that the projector’s start address is correctly set



Replace or repair the DMX cable.

The beam appears dim and its brightness slows sharply



Ambient temperature too high which result in a projector overheating, necessary ventilating measures needed.

10/16

TECHNICAL DATA

VOLTAGES:

100V~240V AC

，

50/60Hz

POWER CONSUMPTION:

400W@220V

LED:

Model LEDEngine (LZ4-04MDCA)

Quantity 19pcs

Manufacturers Rated LED Life 50000 Hours

COLOURS:

RGBW linear color mixing with Macro

COLOR TEMPERATURE CORRECTION:

Linear color temperature correction from 2700K to 10000K

DIMMER:

0-100% linearly adjustable

STROBE:

Electronic Strobe 0 ~25F.P.S

PAN AND TILT:

PAN(0°~540°) and TILT(0°~270) with Auto Position Correction Function

LIGHT ANGLE:

Beam Angle(1/2 Maximum) 7°~42°

Light Spot Angle(1/10 Maximum) 17°~60°

CONTROL:

DMX512, 3 pins and 5 pins interfaces

RDM Control Protocol

12channels in standard mode, and 20 channels in extended mode

Master/Salve Synchronous Control Mode

Self test mode , manual test mode

DMX 512 wireless signal function with optional DMX 512 wireless transmitter

OTHER FUNCTIONS:

Pan & Tilt Speed adjustable

Auto speed adjustment of Fans

Auto light output decrease while lamp temperature is too high

Display’s Brightness adjustable

Lamp temperature & Project’s use time display

11/16

DMX512 Channel Value Display

Menu Invert Function

HOUSING:

High temperature ABS +die-casting aluminum, IP20

WORK ENVIRONMENT TEMPERATURE:

-20°C~40°C

WEIGHT:

Net weight :13Kg Gross Weight: 17. 5 Kg

SIZE

： o268

382

LIGHT OUTPUT:

17°lux(RGBW)

0

38184 9546

4243

2387 1527 1061

60°lux(RGBW)

4m

3m

2m

1m

0m

1m

0

2776 694

308

174 111 77

2m

3m

4m

DISTANCE

（ m

）

0

2 4 6

8

10

12

17°DIAMETER

（ m

）

0

0.63

1.26

1.89

2.52

3.15

3.78

60°DIAMETER

（ m

）

0

2.11

4.22

6.33

8.44

10.55

12.66

276

12/16

13/16

COMPONENT ORDER CODES

NAME

Wireless Antenna

Wireless Receiver

Fuse(VDE Certificate )

Magnet Coupler Board on the Right(with sockets)

Belt

Belt

First Lens

Second Lens

Stepper Motors

Stepper Motors

PWM Speed variable Fan

LED Lamp Board

LCD Display

LED Drive Board

Pan/Tilt Control Board

PART NO.

W006503

W006502

270041037

230020113

290151352

290151353

071100058

071100059

030040235

030040174

030060097

230060339

230060338

230060294

230060340 1

1

1

3

2

1

1

QUANTITY REMARK

1 A40501 360*360

1

1

A40901G4

1

19

19

1

1 HTD447-3M, 8MM Wide

HTD342-3M ,8MM Wide

NMB-MAT PL25L-A24-YHW9

PAN/TILT

Pan/Tilt Motors Control

14/16

15/16

PR LIGHTING LTD.

1582 Xingye Avenue, Nancun Panyu

Guangzhou, 511442 China

TEL: +86-20-3995 2888

FAX: +86-20-3995 2330

16/16

P/N: 320020246

Version: 20140711