Kahomvis FYC-QPW9-609 Black Steel Foldable Electric Treadmill User Manual

Ａｓ　ｐｅｒ　ｉｎｑｕｉｒｙ　ｏｒ　ａｆｔｅｒｓａｌｅｓ　ｓｅｒｖｉｃｅ，ｐｌｅａｓｅ　ｃｏｎｔａｃｔ　ｕｓ　：　Ｃａｔｈｙ＿Ｋａｉｈｏｍｅ＠１６３．ｃｏｍ

Ａｓ　ｐｅｒ　ｉｎｑｕｉｒｙ　ｏｒ　ａｆｔｅｒｓａｌｅｓ　ｓｅｒｖｉｃｅ，ｐｌｅａｓｅ　ｃｏｎｔａｃｔ　ｕｓ　：　Ｃａｔｈｙ＿Ｋａｉｈｏｍｅ＠１６３．ｃｏｍ

Ａｓ　ｐｅｒ　ｉｎｑｕｉｒｙ　ｏｒ　ａｆｔｅｒｓａｌｅｓ　ｓｅｒｖｉｃｅ，ｐｌｅａｓｅ　ｃｏｎｔａｃｔ　ｕｓ　：　Ｃａｔｈｙ＿Ｋａｉｈｏｍｅ＠１６３．ｃｏｍ

3. CAUTION DURING USE

If you do not feel well before using, please consult your doctor or coach.

Please unplug the equipment when not in use.

Please unplug the treadmill before cleaning, moving or change parts for the machine.

Children, the elder and the pregnant are prohibited from using the machine. Patients should consult their doctor before starting any exercise routine.

Please place the machine on a level flat surface. There should be 2M of clearance behind the treadmill.

Do not start the machine when it is folded.

Keep all electrical components, especially motor, power cord and plug, away from water or other liquids.

Do not wear clothes, such as long dress, that might catch on any part of the treadmill while using.

Do not place the treadmill in area that will block any vent or air openings.

Do not put any objects on the machine.

Put away the plug from heated place or fire seat.

Please switch off all functions and pull out plug after using.

Do not stand on the belt while you’re preparing to use the treadmill.

Do not disassemble the machine without consulting professional technicians.

Please make sure the running belt is fastened before using.

4. TECHNICAL SPECIFICATION

Product name

Voltage

Frequency

Speed

Net weight

Treadmill

110V

50-60Hz

0.5-8.5MP/H

28 KG / 62 LBS

Ａｓ　ｐｅｒ　ｉｎｑｕｉｒｙ　ｏｒ　ａｆｔｅｒｓａｌｅｓ　ｓｅｒｖｉｃｅ，ｐｌｅａｓｅ　ｃｏｎｔａｃｔ　ｕｓ　：　Ｃａｔｈｙ＿Ｋａｉｈｏｍｅ＠１６３．ｃｏｍ

10 End Cap 2

Ａｓ　ｐｅｒ　ｉｎｑｕｉｒｙ　ｏｒ　ａｆｔｅｒｓａｌｅｓ　ｓｅｒｖｉｃｅ，ｐｌｅａｓｅ　ｃｏｎｔａｃｔ　ｕｓ　：　Ｃａｔｈｙ＿Ｋａｉｈｏｍｅ＠１６３．ｃｏｍ

Ａｓ　ｐｅｒ　ｉｎｑｕｉｒｙ　ｏｒ　ａｆｔｅｒｓａｌｅｓ　ｓｅｒｖｉｃｅ，ｐｌｅａｓｅ　ｃｏｎｔａｃｔ　ｕｓ　：　Ｃａｔｈｙ＿Ｋａｉｈｏｍｅ＠１６３．ｃｏｍ

Ａｓ　ｐｅｒ　ｉｎｑｕｉｒｙ　ｏｒ　ａｆｔｅｒｓａｌｅｓ　ｓｅｒｖｉｃｅ，ｐｌｅａｓｅ　ｃｏｎｔａｃｔ　ｕｓ　：　Ｃａｔｈｙ＿Ｋａｉｈｏｍｅ＠１６３．ｃｏｍ

Ａｓ　ｐｅｒ　ｉｎｑｕｉｒｙ　ｏｒ　ａｆｔｅｒｓａｌｅｓ　ｓｅｒｖｉｃｅ，ｐｌｅａｓｅ　ｃｏｎｔａｃｔ　ｕｓ　：　Ｃａｔｈｙ＿Ｋａｉｈｏｍｅ＠１６３．ｃｏｍ

Ａｓ　ｐｅｒ　ｉｎｑｕｉｒｙ　ｏｒ　ａｆｔｅｒｓａｌｅｓ　ｓｅｒｖｉｃｅ，ｐｌｅａｓｅ　ｃｏｎｔａｃｔ　ｕｓ　：　Ｃａｔｈｙ＿Ｋａｉｈｏｍｅ＠１６３．ｃｏｍ

12.RUNNING BELT ADJUSTMENT

(1) Running belt deviate t

。 left

Start the machine by speed at 1.2-1.8 MPH without loading, use Allen wrench to screw the bolt 1/4 turn clockwise (see fig1). Keep the machine running without loading for 1-2 minutes to gauge. Repeat the previous step if more adjustment is needed, until the belt moves to the center.

(2) Running belt deviate t

。 right

Start the machine by speed at 1.2-1.8 MPH without loading, use Allen wrench screw the bolt 1/4 turn clockwise (see fig2). Keep the machine running without loading for 1-2 minutes to gauge. Repeat the previous step if more adjustment is needed, until the belt moves to the center.

(3) Running belt slipping

If the running surface becomes slipping, tighten bolts on both ends 1/2 turn clockwise (see fig3) with Allen key. Repeat if necessary until the belt is properly adjusted.

Ａｓ　ｐｅｒ　ｉｎｑｕｉｒｙ　ｏｒ　ａｆｔｅｒｓａｌｅｓ　ｓｅｒｖｉｃｅ，ｐｌｅａｓｅ　ｃｏｎｔａｃｔ　ｕｓ　：　Ｃａｔｈｙ＿Ｋａｉｈｏｍｅ＠１６３．ｃｏｍ

Ａｓ　ｐｅｒ　ｉｎｑｕｉｒｙ　ｏｒ　ａｆｔｅｒｓａｌｅｓ　ｓｅｒｖｉｃｅ，ｐｌｅａｓｅ　ｃｏｎｔａｃｔ　ｕｓ　：　Ｃａｔｈｙ＿Ｋａｉｈｏｍｅ＠１６３．ｃｏｍ

FCC COMPLIANCE STATEMENT:

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.

FCC Radiation Exposure Statement

The device has been evaluated to meet general RF exposure requirement.

The device can be used in portable exposure condition without restriction.