PLUS eBridge4SK

Ethernet over Coax 4-Port Adapter Kit

eBridge100SPR

- EoC Receiver

eBridge4SPT

- 4-Port PoE/PoE+ EoC Transceiver Switch

Installation Guide

Z1409

I.T.E. 43KC

Rev. 072313

More than just power.

TM

Installing Company: _______________ Service Rep. Name: __________________________________

Address: _____________________________________________ Phone #: __________________

Table of Contents:

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

pg. 3

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

pg. 3

Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

pg. 4

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

pg. 4

Typical Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

pg. 5

Maximum Length of Coax Type vs. Camera Power/PoE Class . . . . . . . . . . . . . . . . . . . . . . . .

pg. 5

Shelf Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

pg. 6

Chassis Mechanical Drawing & Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

pg. 8

- 2 - eBridge4SK Installation Guide

Overview:

Altronix eBridge4SK kit consists of eBridge100SPR and eBridge4SPT which are Coax to CAT5 Ethernet adapters/ media converters that deliver data and power over coax cable. eBridge4SK enables fast 10/100 Base-T Ethernet digital communication. eBridge4SPT allows you to upgrade your existing infrastructure by replacing a single analog device with up to four (4) PoE/PoE+ devices. eBridge100SPR passes data and sends power over the coax to the eBridge4SPT. Data transmission and power over the Coax are possible up to 300m. Maximum range from head end to the PoE camera/device is 500m, taking into consideration that up to 100m of structured cable may be deployed at each end. eBridge4SK enables cost-effective system upgrades and eliminates the costs and labor associated with installing new network cabling.

Note: for Ethernet maximum distance see Maximum Length of Coax Type vs. Camera Power/PoE Class, pg. 5 .

Agency Listings:

• UL 60950-1 Information Technology Equipment.

• CE

• C-Tick

European Conformity.

C-Tick compliant.

Input:

• eBridge100SPR - 51-56VDC/60W max. power.*

eBridge4SPT - powered by eBridge100SPR.

Power Output:

• eBridge4SPT: 4 ports PoE+ (30W) per port.

• Total output power: 60W.

Ethernet:

• Connectivity: RJ45, auto-crossover.

• Wire type: 4-pair CAT5e or better structured cable.

• Distance: up to 100m.

• Speed: 10/100BaseT, half/full duplex,

auto negotiation.

Coax:

• Throughput is rated to pass 100Mbps of data at

distances up to 300m.

• Connectivity: BNC, RG-59/U or similar.

• Throughput is rated to pass 100Mbps from camera

to receiver. With the proper headend equipment

multiple Megapixel cameras can be used.

LED Indicators:

• Blue LED - Coax link connection.

• Green LED - Power (eBridge100SPR only).

• Yellow and Green LED (RJ45) IP Link status,

10/100Base-T/active.

Features:

Environmental:

• Operating Ambient Temperature : eBridge100SPR: – 40ºC to 60ºC

(– 40ºF to 140ºF).

eBridge4SPT (60W): – 40ºC to 75ºC

(– 40ºF to 167ºF).

• Storage Temperature: – 40ºC to 75ºC

(– 40ºF to 167ºF).

• Humidity: 20 to 85%, non-condensing.

Applications:

• Retrofit digital IP cameras in an analog CCTV

installation (up to four (4) IP cameras expansion per

analog camera).

• Works with Megapixel, HD720, HD1080 and VGA

(SD) cameras (see note, pg. 4) .

• Extend Network link distance in an

industrial environment.

• Upgrade deployed CCTV Coax to a digital network

in Retail, Hospitality, Arenas, Casinos, Airports,

Schools, Hospitals, Transportation, etc.

Mechanical:

• Dimensions (H x W x D approx.):

eBridge100SPR:

4.375” x 3.5” x 1”

(111.1mm x 88.9mm x 25.4mm)

eBridge4SPT:

1.75” x 5.25” x 9.25”

(44.5mm x 133.4mm x 235mm)

*UL Listed Class 2 or limited power source (NetWay1D).

eBridge4SK Installation Guide - 3 -

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application.

eBridge100SPR and eBridge4SPT is not intended to be connected to outside plant leads and should be installed indoors within the protected premises. eBridge100SPR and eBridge4SPT are intended for indoor use only.

1. eBridge100SPR installation:

a. Secure unit to desired mounting surface with a proper fastening device utilizing the unit’s mounting hole.

Unit should be mounted in proximity to Ethernet switch/network, NVR or video server.

b. Connect 56VDC UL Listed Class 2 or limited power source to terminals marked [Power – Input +]

(observe proper polarity) (Fig. 1, pg. 5) . Use 22AWG-16AWG wire for this connection.

Caution: 56VDC will be present on coax. The other end of the coax should only be connected to the

eBridge4SPT.

c. Connect structured cable from Ethernet switch/NVR (network video server) to RJ45 jack marked

BaseT] .

d. Connect Coax cable to BNC connector marked [Coax] (Fig. 1, pg. 5) .

2. eBridge4SPT installation:

a. Affix rubber pads to eBridge4SPT for shelf installation (Fig. 2, pg. 6) .

b. Connect Coax cable from eBridge100SPR to BNC connector marked [Coax] located on the back of the

(Fig. 1, pg. 5).

c. Connect structured cable from PoE/PoE+ cameras/devices to RJ45 jacks marked [1-4] (Fig. 1, pg. 5) .

Note: The eBridge is designed to accommodate Megapixel, HD720, HD1080 and VGA (SD) cameras. It is important to note that some high resolution and high frame rate cameras may demand faster headend processing ability, such as a PC graphics card to present a quality image. If the headend processing equipment is insufficient in speed, the image may show pixelation and latency. It is advisable to pre-test system if unsure. Alternatively, frame rate and resolution may be reduced to accommodate system equipment.

Parameter

Connections

Input Power

Requirements

Indicators

Environmental

Conditions

Regulatory

Compliance

Weights (approx.)

Technical Specifications:

Description

BNC for Coax link. RJ45 for Ethernet link.

eBridge100SPR - 51-56VDC/60W @ max. power.

eBridge4SPT - powered by eBridge100SPR.

Blue:

Yellow (RJ45 connector):

Green (RJ45 connector):

Coax Link.

On - Link, Off - No Link, Blinking - Activity.

On - 100Base-TX, Off - 10Base-T.

Operating Ambient Temperature (UL60950-1):

eBridge100SPR:

eBridge4SPT ( 60W):

Storage Temperature:

Relative humidity:

Operating Altitude:

– 40ºC to 60ºC (– 40ºF to 140ºF).

– 40ºC to 75ºC (– 40ºF to 167ºF).

– 40ºC to 75ºC (– 40ºF to 167ºF).

85%, +/ – 5%

– 304.8 to 2,000m.

UL/cUL Listed for Information Technology Equipment (UL 60950-1).

CE European Conformity.

eBridge100SPR: Product: 5.1 oz. (0.144 kg) eBridge4SPT: Product: 2.9 lb. (1.32 kg)

| Shipping: 7.76 oz. (0.22 kg).

| Shipping: 3.9 lb. (1.77 kg).

- 4 - eBridge4SK Installation Guide

Fig. 1

Typical Application:

eBridge100SPR

56VDC

Input

NVR Network

Video Server

(Head End

Equipment)

Ethernet Switch

CAT-5e up to 100m eBridge4SPT (Front View)

Coax up to 300m

Output

Base-T

CAT-5e up to

100m

CAT-5e up to

100m

PoE/PoE+

Cameras

PoE/PoE+

Cameras

Maximum Length of Coax Type vs. Camera Power/PoE Class:

Camera Power/

PoE Class

13W/0 or 13W/3

25W

60W

RG59/U

(23AWG)

261m

119m

51m

RG59/U

(22AWG)

335m

151m

64m

RG59/U

(20AWG)

Max. Length (meters)

500m

240m

101m

RG59/U

(18AWG)

500m

366m

160m

RG6/U

(18AWG)

500m

366m

160m

eBridge4SK Installation Guide - 5 -

Shelf Installation

A

1- Position and affix rubber pads (included) at each corner on the bottom of the unit (Fig. 2) .

2- Place unit in desired location.

Fig. 2

B

Mounting Hardware

(Included):

Four (4) rubber pads C

Left side

Rubber Feet

- 6 - eBridge4SK Installation Guide

Notes:

eBridge4SK Installation Guide - 7 -

Fig. 2

eBridge4SPT Chassis Mechanical Drawing & Dimensions

(H x W x D approx.)

:

1.75” x 5.25” x 9.25” (44.5mm x 133.4mm x 235mm)

SLOC link LED

1.75”

(44.5mm)

5.25” (133.4mm)

Coax

8.42”

(213.9mm)

9.25”

(235mm)

PoE

Output

10/100

Base-T

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

140 58th Street, Brooklyn, New York 11220 USA | 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty

IIeBridge4SK G19U MEMBER

- 8 - eBridge4SK Installation Guide