INSTAUCTIO MANUAL

Add to my manuals
27 Pages

advertisement

INSTAUCTIO MANUAL | Manualzz

Please completely read and understand the entire manual before using, assembling and/or disassembling your remote controlled car.

1/BTH SCALE ELECTRIC POWERED 4WD SAnD RAIL' BUGGY

INSTAUCTIO MANUAL

Tectinical Dat

LENGTH

535MM

WIDTH HEIGHT

19DMM

This data is subject to change without prior notice.

WHEELBASE WHEEL DIA. WHEEL SPAN GEAR RATIO

• Four Wheel Drive System

Full Aluminum Oil Filled Shocks

• 6KGs Steering Servo

• Factory-Assembled with Factory-Printed Body

• 2.4GHz Radio System

• Bevel Differentials, Front And Rear

• Adjustable Camber, Front And Rear

• Adjustable Bump Steer, Shock Mounting Positions And Droop

• Adjustable Differentials With The Use Of Differential Grease

• High-Grip, All-Terrain Tires Mounted On Spoke Type Wheels

• Uses Li-po Battery ( 11.1 V, 3000mAH) and Li-po Pocket Charger

(Battery and charger need to be separately purchased)

This product is not a toy. It is not intended for persons under 14 years of age, unless closely supervised by an adult .

Thic:; m::lnll::ll ic:; c:;11hiPrt tn rh::lnnP without notice .

This user's manual contains the instructions you will need to assemble, operate and maintain your vehicle. We know you are anxious to start driving, but it is very important that you take tin:e to read the manual even if you are an experienced R/ driver .

Carefully read and follow all instructions in the manual. Failure to follow the instructions will be considered abuse and/or neglect and may void the warranty.

Your vehicle is designed to run on uneven or rough terrain. However, dust, sand, water and carpet fibers can lodge in any moving parts and can damage your vehicle if not removed promptly. Your warranty does not cover damage due to outside elements including sand, dirt, water or any other debris. You are responsible for the maintenance and safe operation of this vehicle.

This product is not a toy. It is not suitable for users under 14 years old unless supervised by an adult.

Never attempt to re-assemble any electronic components. These have been carefully calibrated at the factory.

Only use our factory manufactured parts to upgrade your car. If you perform a drive train upgrade, replace the entire system (Such as motor, ESC/receiver unit and the like) so that all components are properly matched. Any malfunction incurred by custom modification will void your warranty.

Before driving your vehicle, please read this manual completely and examine your vehicle for any defects. Test your remote control to make sure it functions properly and at the range you plan to run your vehicle.

For best performance, some adjustments may be necessary.

This vehicle requires one battery pack, which is included with the car. The radio controller requires three AA size batteries (not included). Make sure the vehicle's batteries have a sufficient charge before driving or possible loss of control may result.

Always remove batteries from the vehicle and the radio controller when not in use.

Please operate your vehicle in an open area free of obstacles. Never operate your vehicle in crowded street.

This product is fully assembled at factory. our factory is not responsible for damage and/or accidents that occur as the result of custom modifications and/or incorrect operation.

.

------------------------------------------------------------------------------------~

We want you to enjoy your R/C vehicle and to operate it with care. Failure to operate your vehicle in a safe and responsible manner may result in injury to yourself and others and may cause damage to property.

Read and understand all instructions carefully before use and assembly/disassembly.

Do not run your vehicle on public roads or any area where you may encounter pedestrian or vehicle traffic.

Do not operate in a congested area or in crowds.

Do not operate your vehicle with obstructed Line of sight, at night, or near water.

Your vehicle is radio controlled. Radio waves are subject to interference. Radio interference can cause loss of control of your vehicle.

Take care not to injure yourself while using tools to adjust or upgrade your vehicle.

Since the model contains many small parts, keep out of reach of children while assembling and/or disassembling.

When turning off your model, always turn off the receiverfirst, before turning off the remote control.

Always remove the batteries from your vehicle and the remote control when not in use.

If your vehicle becomes stuck, release the th rattle, then retrieve it by hand.

Do not continue to apply the throttle or you may damage the motor and/or the

ESC/receiver unit.

Turn off your vehicle and discontinue use if it runs erratically. Do not run it again until the issue has been found and resolved.

YOUR .4GHz RADIO SYSTEM

Your car is equipped with the new 2.4GHz radio system. Please read and understand all instructions below before operating.

A: Steering Wheel

1: Steering Trim 4: Power Switch 7: Throttle Reverse

B: Trigger 2: Steering Reverse

5: Steering Dual Rate 8: Green Indicator

C: Battery Case

3: Red Indicator

6: Throttle Trim

9: Bind(Pair) button

Steering Wheel:

Proportionally operates the models right and Left steering control.

Battery Case:

Requires 3pcs of AA size batteries.

Power Switch:

Used to turn the radio controller ON/OFF

Steering Dual Rate Dial:

Allows you to change the amount of steering servo travel compared to the amount of physical movement ofthe steering wheel.

Throttle /Steering Trims:

Used to adjust the center trim of the throttle/steering channel.

Steering Reverse:

Allows you to electronically switch the direction of steering servo travel.

For example, if you move the steering wheel to the right and the steering servo moves to the

Left, flip the Steering Reverse Switch to make the steering servo move to the Left.

Throttle Reverse:

Allows you to electronically switch the direction that the motor operates in relation to the throttle trigger. For example, if you pull the throttle trigger to accelerate forward, but the model goes in reverse, flip the Throttle Reverse Switch to make the model accelerate forward.

Trigger:

Controls the speed and braking ability of your car. Pull it to accelerate, release it to dec .

elerate, and push it to brake. Pushing it a second time activates the reverse feature.

Indicators:

Shows battery power Level. Green indicator flashing means battery power is Low.

If both red and green indicators are flashing then the radio controller battery is too Low to control the model and you must replace with fresh batteries immediately.

Bind(Pair) button: It is used to bind your 2.4GHz radio system.

BATTERY INSTALLATION

1) Slide the battery cover as shown and install 3pcs of

AA size batteries, positioning the polarity as indicated.

2) Replace the battery cover after batteries are installed.

NOTES:

-Use batteries of same type.

-Remove batteries from the case if not in use.

-Always check the battery power .

-Dispose of exhausted batteries properly .

..

,

__________________________________________

__

TO BIND THE RECEIVER TO THE RADIO CONTROLLER

Before running, make sure that the radio controller is bound with the receiver. This has been done at the factory, but if the model is not responding to the controller, it is possible that the controller and receiver are not bound, and you must perform the binding procedure following the instructions below.

·Channell to steering servo

• Channel2 to ESC (or throttle servo)

BIND BUTTON

ON RECEIVER

Press the BIND button a second time to activate FAIL

SAFE feature by the time the binding process is completed. ress an

=-~-hold

1) Press and hold the Bind Button on the receiver by using a screwdriver as shown, while turning on the power switch on the car. (The power switch is located on the rear indicated by Label.)

2)

Hold the Bind(Pair) key and switch on the power on the radio controller .

You must hold the Bind(Pair) within

5 seconds of turning on the receiver on the car.

3)

The green indicator should flash, meaning that the binding process is being performed.

4)

Once both red and green indicator are Lit and not flashing, then your receiver is bound to your radio controller . The binding process is complete .

RUNNING YOUR CAR

8

TURN ON THE RADIO CONTROLLER TURN ON THE RECEIVER ON YOUR CAR

Power

L------------------------------------------------------------------------------------------4·

NOTES:

--Before using your car, make sure the radio controller has sufficient battery power.

If the battery power is too low it can lead to the loss of control of your car.

--Always turn on the remote controller

FIRST,

and then the receiver.

e

CHECK STEERING PERFORMANCE

• Ensure good steering performance.

TURN LEFT TURN RIGHT

1) To keep the car running in a straight line, do not move the control wheel. (Keep it centered)

2) Turn the control wheel left to allow your vehicle to turn left.

3) Turn the control wheel right to allow your vehicle to turn right.

CHECK TRIGGER RESPONSE

PUSH IT r:2;RWARD

CENTRE

A. Pull the trigger back to accelerate, release it to decelerate and push it forward to brake.

B. To stop accelerating your car, release the trigger to Neutral.

C.

Pushing the trigger forward a second time activates the reverse feature.

TO TUNE THE STEERING TRIM

Gently pull the trigger to allow your car to accelerate slowly. Meantime, tune the steering trim to align the front wheels.

.

-~--------------------------------------------------------------------------------------~

TO TUNE THE STEERING DUAL RATE CONTROL DIAL

Decrease

¢:J

¢

Increase

STEERING D/R

This dial adjusts the overall travel of the steering servo. Push the dial forward for maximum steering. Pull the dial back to reduce the steering level.

-Set the Steering Dual Rate Control Dial to Minimum first. To set the desired steering level increase it again whilst decelerating your vehicle.

Follow the illustrations above to install the Li-po battery pack in your car. The battery cover is located on the bottom ofthe chassis .

1) Pinch the battery cover blocks as shown to open the battery cover. (See Figure 1)

2) Lift the battery cover. (See Figure 2)

3) Connect the battery to the ESC as shown. Note: The vehicle uses banana plugs--make sure to connect black to black and red to red .. (See figure 3)

4) Install the battery foam and replace the battery cover. (See Figure 4)

Your RTR vehicle is equipped without battery and charger unless individually purchased .

Here is our practical pocket Li-po battery charger which you might use with your vehicle .

Input Voltage: 110-240 V AC

Output Current: 1.0 A

Indicator: 3x LED

Max. Charging Current : 1.0 A

Size: 100 mm

*

60mm

*

35 mm

Weight: Approx. 180g

Power Supply Slot

1) Connect the pocket balance charger to power supply by using the power supply cord provided in the package.

The indicator lights will turn green meaning that the charger is ready.

2) Connect the battery to the corresponding slot. (If it is

35( 11.1 V) battery, please connect it to 35 slot ... )

When the battery is initially connected, the indicator lights will turn Red meaning that charging has begin.

Once the battery is fully charged, the indicator lights will turn green again.

Note: The batteries use banana plugs--make sure to connect black to black and red to red.

6

Warning

• Ensure all cords are connected firmly during charging.

• Never touch the charger with wet hands.

• Never charge battery unattended.

• Store the charger in a dry place away from direct sunlight.

Never use it near any source of heat and water.

• Children must not handle the charger without adults' supervision.

STOPPING YOUR CAR

0

TURN OFF THE RECEIVER ON YOUR CAR TURN OFF THE RADIO CONTROLLER

Power

.&

CAUTION

• Always switch off the receiver ,and then the radio controller.

e

REMOVE BATTERIES

• Do not forgot to remove batteries from your car and radio controller when not in use.

···--------------------------------------------------------------

This vehicle is fully assembled at factory. The following illustrations facilitates replacement.

(Note: For these plum/star head screws, you can use either Standard Hex Screw drivers (1.5mm, 2mm, 2.5mm) or Plum/Star Head screwdrivers.).

First remove the roll·cage: l)Remove the eight screws

(69586)from the chassis as shown in the figure one by one.

2)Remove the four screws

(69580) from the hood as shown in the figure one by one.

3) Remove the screw (69590) from the rear unit on the one side as shown in the figure.

4)Remove the screw(69590) 5) Remove the rear shock from the rear unit on the other from one side using needle side as shown in the figure. nose pliers.

6) Remove the rear shock from the other side using needlenose pliers.

7)Hold the rear suspension, 8) Push gently on the other remove the roll cage from one side to remove the roll cage as side. shown in the figure.

The roll cage is removed from vehicle. You are now ready to check motor and ESC if possible.

To replace the roll cage follow the steps again in reverse.

Tip: Before re-installing the roll cage, check all parts carefully and make sure they have not come loose and are properly secured.

CHASSIS TUNING GUIQE

Your model can be customized to enhance speed and performance. Simple adjustment and easily maintained setting will assure optimum operation and performance. When making adjustments, do so only in small increments and always check for other parts of the vehicle that are affected.

Many after market options are available to make your R/C vehicle faster and stronger. Please read the section carefully and it always make sure you write down your base settings in case you need to refer to them at a Later date.

Front Steering Toe Angles

The front steering toe angle has a dramatic on how your car performs and how your t i res wear . You can have toe-in, zero toe or toe-out. This can be adjusted by turning the front turning linkage set with an adjustable wrench .

Toe Out

Front Turning Linkage Set

Toe In

Front Turning Linkage Set

Toe-in will be less reactive and cause the vehicle to under steer(the front wheels push straight on while turning).

Th i s can be advantageous for operators struggling to get to grips w i th the driving of the vehicle .

Toe-out will be more aggressive on the steering response especially on small steering inputs. This will make the car want to over steer(rear wheels slide on small steering inputs).This is useful as a race tuning aid to ga i n extra steering .

Zero toe w i ll make the front wheels run straight and make the car very neutral. Tire wear will also be reduced and the vehicle will feel easier to drive.

Camber Adjustment

Camber can be adjusted on all4 wheels of the car . You can have negative camber or positive camber which will affect the contact patch of the tire both statically and while cornering .

Camber i s mainly used to control the wear of the tire . You should adjust the camber to equal the wear all across the surface of the tire. Camber is adjusted by the upper link turnbuckle linking the wheel to the chassis front and rear .

\ .

• •.. Vertical

Positive\

"m'., __ \__

This is an example of positive camber.

This is when the bottom of the wheel is closer to the centre ofthe car compared to the top of the wheel. Positive camber will give less contact area in the corner and less grip. Excessive amounts will cause less grip and uneven wear.

Vertical ;

Negative!

.

.

··· · •

f

.

.

.

.

.

.

. cambe r l

j

'

.

...... JJ ....

..

..

This is an example of negat i ve camber .

This is when the top of the wheel is closer to the centre of the car compared to the bottom of the wheel. Negative camber will give more contact area in the corner and more grip . Excessive amounts will cause less grip and uneven wear .

• •r----------------------------------------------------------------------

---

GLUE THE OUTER PERIMETER OF THE LENS AND INSTALL

The off-road Light lenses are optional parts. l.Remove the five off-road Light grills. (fig.2)

2.Apply a small bead of glue (CA) around the outer perimeter of the first lens.(fig.2)

3.Carefully Line up the notches in the lenses with the tabs inside the Light housing and install.

4.Repeat steps 2-3 for remaining four front lenses.

5.Reinstall off-road Light grills. (fig.4)

6.Apply a small bead of glue (CA) around the outer perimeter of the first rear lens. (fig. 5)

7 .Align the lens with the rear Light housing and push into place.

8.Repeat steps 6-7 for the remaining three rear lenses.

INSTALLATION

The radiator is an optional part. l.Gather all five parts of the radiator assembly. (fig.l)

2.Align the fan and shroud onto the radiator shaft. (fig.2)

3 .Using a torque driver, insert the (69600) torque screw into the end of the shroud and tighten.

4.Repeat steps 2-3 to complete the radiator assembly. (fig.3)

5. Using a torque driver, remove the rear Light assembly by removing the two screws securing it from the underside of the roll cage. (fig. 5)

6. Fasten the radiator assembly from the top using two (69593) screws. (fig.6)

7. Reinstall the rear Light assembly. (fig. 7)

DASHBOARD

COCKPIT

The cockpit is an optional part. l.Uninstall the roll cage from the chassis.

2.Remove all14 screws securing the hood and remove from roll cage.(fig.l)

3.Insert the cockpit into the underside of the roll cage(fig.2),be sure the front of the dashboard is on top of the roll cage. (fig.3&5)

4.Secure the cockpit from the underside using the included(69610) screws .

(fig.4)

S.Reinstall the front hood and secure in place. Be sure the two rear holes of the hood line up with two holes in the dashboard.(fig.S-6)

After running your car, perform the following procedures regularly to maintain your car's performance.

• Inspect your car for any obvious damage.

• Check the gears·for wear, debris or broken/slipping teeth.

• Check the wheels and tighten the wheel screws properly.

• Check for Loose screws in the chassis.

• Check the wiring for frayed or damaged wires or connectors.

• Check the steering servo which will wear out over time and require replacement.

• Check all batteries.

• Keep the chassis clean and free of sand, dust, moisture and any other debris.

Remove and clean the motor if necessary. (Never attempt to re-assemble the motor, you will damage it and void the warranty).

• Clean the car body with a soft Lint-free cloth.

• Remove all batteries from the car when not in use.

A. The vehicle does not work at all.

1.

Check to see if radio controller and car are on.

2. Check to see if radio controller and receiver are properly bound.

3. Adjust throttle trim on the radio controller

B. The vehicle runs slow.

1.

Replace or charge the battery pack and/or the radio batteries.

2. Make sure the vehicle is geared properly and the pinion and spur gear are over tightened.

f------

1 3.

Clean all bushings or ball bearings.

'-------

1 4.

Check for stripped or dirty gears.

C. The throttle works, but not the steering.

C

~ ~

l.Adjustthethrottletrim.

D.

It steers, but no throttle control.

1.

Check if the servo feels jammed, try centering carefully it by hand.

1 2.

Check all the steering linkage for any damage.

E. The vehicle runs noisily.

1.

Check gear mesh between spur gear and pinion.

E

1 2.

Check for stripped and/or dirty gears.

1 3.

Clean and oil bushings or ball bearings.

I"'"

1

69500R 69501R

69502 69503

Chassis

69504R

Roll Cage Front Unit

Roll Cage Top Unit

1 69506 -

I

~oll

Cage Rear Unit+

rs;r~~; ~ost+Retaine

~

Front Bumper Brace

& Roll Cage Side Rails Roll Cage Rea r Rails

' Assembly

I Assembly

1 - - - - - - - - - - - - - - - - j - - - - - - - - -

69508

..

_

-

-·~

'

.

Shock Towers (Fr.&Rr.)

Gear Box Assembly

- - + - - - - - - - -

- - - f - - - - - ·

69511

1

69510

,...

. I , . . ,

' . I

I

Left/Right

Suspens1on Arms (Lower Suspension Arms (Lower Steering Knuckles

Front) Rear)+Shock Retainers

Left/Right

Rear Hub Car _ _ _ _ _ _ F r _ o _ t _ _ ub Carriers

69512R

1

69513

1

69514R

1

69515

~~&:-....-

Suspension Arms (Lower l

Rear)+Shock Retainers Spur Gear ( 56T)

69516R

I

69517RA

1

f/4 · - ,

) 2 .

C

9 a Je l

~

. ,

.....

Centre Diff . Mount Set+

Suspension Mount Set+Servo Servo Saver Assembly A+ j

Retainers+Centre Diff.

Retainer

Bumper Lowe Mount Set+

Servo Arm

69517RB -

~

69518

-

~

-

__

.

.,.._

::._~

Battery Guard+ESC

Bottom Mount

*

I

&e eo

Front/rear light I Radiator Assembly+

I I

I I

assembly

[ Screws

NOTES : THE 1/Y.GES OF THE

P~QTS l'fV'.Y

1/A,.QY FQO"' yOUQ A,.CTUA,.LLY QECEII/EO PA..QTS.

J

Off Road Buggy

69519

LIST

FO~ ~EPLl\CEMENT Pl\~TS

69520 69521

69522

I

Wheels -Spoke Style

69523

Tires/Sponge Insert

69524R

2P

Wheels Complete

69525

2P

Centre Diff . Complete

69526

Battery Cover

(assembled)

1 69527

' Motor Guard Set

69531

69 .

6mm (front)

161.6mm(rear)

Center Drive Shafts

(Front and rear)

2P

69528

..

2P

Rear Drive Shafts

(91.2mm)

~ ear

Wheel Shafts

69529

1 69530

0

5 a 0

i

2P :

2P

Front CVD Drive Shafts

69532

2P

Front Upper Linkage Set

69533

2P

Rear Upper Linkage Set

69534

0

7

2P

Steering Linkage Set

69572

Servo Linkage Set

69536

2P

I

2P

Full Aluminum Oil Filled Full Aluminum Oil Filled

Shocks (Front) Shocks (Rear)

69537 69538

I

/ / / /

!) !) !) !)

2P

Front Skid Plate

(Aluminum)

Rear Shock Upper

Retainer

Diff. Shafts +E Clip

(2mm) (Front/Rear)

-

NOTES: THE lfo\>\(jES OF THE

P~~TS

11\1\Y

VA.QY FQOf't

YOU~

A,.CTUA,.LLY QECEIVED PA,.QTS

.

2P

I

Hinge Pins-Lower

Outer+E-Clip (2mm)

<1> 3 * 30.9mm

4P

I

- - - - - - - - - - - - - - - ---

69539

LIST

FO~ ~EPL~CEIY\ENT P~~TS

--.--

----------------

69540

- - - - - - - - - - - - - - - --

69541

----

--------

69542

I

00

0

/ /

/I

Hinge Pins-Lower Inner

<1>3*60.3mm

69543

4P i

Servo Saver Assembly B

+Ackerman Plate

69544

Steering Posts

69545

2P

Front/rear

I

Centre Diff.

Outdrives

69546

2P

Centre Outdrives+

Set Screws 3*3-2*7)

2P

69547

" "

8P

Step Ball Stud.

<1>4.8*16.6

- - - - -

69548

00 0 0

00 0

8P

8P

Steering Knuckle

Bushinges

- - - - -

69549

Front CVD Shaft Clips

69550 oooo oooo oooo

12P

8P

"

8P 8P

Ball Stud. <1>4.8*6.8

69551

Ball Stud. <1>4.8*8.5

69552

Shock Inner Oil Bowls

69553

Shock 0-ring

69554

Washers

(<1>3.1 *6*0.5mm)

69555

2*10mm

JJ

2.5*22mm 5*6.8*1.3mm

= oo

12P

Diff. Paper Washers

69556

8P

Steering Plate

Bushinges

69557

5 * 17 * 0 .

3mm

8P

Flange Ball Bearings

(3*6*2.5mm)

69558

8P ,

Diff. Pinions+Pins+

Washers+O-ring+ Diff. Case

Front/rear Diff.

Complete

[ Servo

(6~gs)

NOTES: THE IMAGES OF THE PAinS MAY

1/A~Y F~Ofl\

YOUJ<I ACTUALLY

~ECEII/ED

PAPTS .

.L

Brushed Motor

LIST FOQ QEPLI\CEN\ENT P"QTS

69559

sptash Resistan

e i )

Brushed ESC ( w/banana plugs)

69563R

Mounting Hole : Smm

(brush less only)

Mounting Hole

1

: Smm

Motor Pinion (20T) Motor Pinion (13T)

+Set Screw 4*4 +Set Screw 4*4

-

~~-

- - - - - -

69564 69576

~ I

1

Brushless Motor

2574)

- -

- -

69577

~ I

~ I

I

.t~ i

I

I

Splash Resistant

Brushless ESC

· w/banana plugs r---~-----

.

69568

···---~----

I

Body Assembly

Light lenses(front/rear)

Body Assembly

+gear lever

------1

(Blue) (green)

6957 4 --~

____ _

Li-po Battery 11.1 V,30c,

3000mAH (w/banana

1

Li-po Battery Charger+ Li-po Battery Charger+ plug)

European Standard Plug Australia Standard Plug I

Zip Tie (Big)

POll

cr-crcr-crcr-crcr-cr-

8P

Zip Tie (Small)

H007

Pl20

Wheel Hex.

- - - - -

H009

4P

P019

1 PlOl

·

8P

I

I

~

I

00

00

4P .

Receiver Antenna Pipe

2P

Motor Pad

___,

H002 H003

6

<&

a a a el

6P 4P

Ball Bearing 5*11 *4

Ball Bearing 10*15*4 j

Lock Nut M3

NOTES: THE lft\1\GES OF THE

P~~TS

to\1\Y

VA.~Y F~0/1\ YOU~

A,CTUA.LLY

~ECEIVED PA.~TS .

6P

I

___ l

FlangeLockNutM4

6P i

H013 H022

T

H153 H100 nnnn nnnn

=

...;J

8P

I

I

I

Wheel Hex. Pin

Ball Stud. <1>4.8*11.2 I (2*10mm)

~--------~-------

8P

6538-H005 1 3338-1010

E Clip (2mm)

E710

8P

69571

_ j

Bevel Gears(Large+

Small) (Front/rear/

Centre)

Diff. Main Gear+ Pinion

69580

1 69581

Receiver 2.4Ghz Cockpit

- - - - - - · - - - - - - - - - + - - - - - - - - - - - -

69582 69583

Plum Blossom Washer

12P

I

I

Plum Blossom Washer

Head SelfTapping Screw I

12P

Head SelfTapping Screw

3*8mm

3*10mm

Plum Blossom Washer

Head Screw 3*10mm

12P

Plum Blossom Washer

12P

I

Head Self Tapping Screw

3*12mm

69584 69586 69587 69585

uu.u

/,//,//,/

Plum Blossom Washer

Head Screw 3*12mm

12P

Plum Blossom Washer

Head SelfTapping Screw i

~·~2;;;m•ll

he.d

)_ __

12P

69588

12P

Plum Blossom Washer

Head Self Tapping Screw

3*14mm

12P

Plum Blossom Washer

Head Self Tapping Screw

3*16mm

1

69590 69591

I

I

I

12P

I

Plum Blossom Washer

Head Self Tapping Screw

3*18mm

I

I

I

Plum Blossom Washer

Head Screw 3*14mm

12P

Plum Blossom Washer

Head SelfTapping Screw

3*2lmm

-

"''"T.:c. Tu.: IMAm•< oF THE

PAins

MAY VARY FRO/I\

you~

ACTUALLY

~ECEII/Eo PA~TS .

12P

Plum Blossom Washer

Head SelfTapping Screw

3*24mm

,--~----~--

--

--~~---

-

69592

--

-------~----

----

69593

I

I

12P

til

I

~

I

til til

I

I

I

I

l i

12P

ti til

12P

I

~~~

12P

Plum Blossom Washer Plum Blossom Washer

Plum Blossom Washer Plum Blossom Washer

Head SelfTapping Screw Head Self Tapping Screw

Head Self Tapping Screw Head SelfTapping Screw

3*37mm

2.6*12mm 2.3*14mm 2 .

3*8mm

I

69596

69597

---

-

----- --------

69594

69598

--------------

--------------------

69595

69599

til

I

I

I

I

til

I

I

I

I

I

I til

I

til

I

12P

Plum Blossom Washer

Head Screw

2.5*17mm

12P

Plum Blossom Washer

Head Screw

2.5*14mm

I til ti I

i

12P

Plum Blossom Washer

Head Self Tapping Screw

2 .

3*14mm

12P :

Plum Blossom Washer

Head Self Tapping Screw

2.3*8mm

69600 69601 69602 69603

IIIII I IIIII I IIIII I

IIIII I

I

IIIII I IIIII I IIIII I IIIII I

12P 12P

Plum Blossom Plum Blossom Plum Blossom

Countersunk Self Tapping Countersunk SelfTapping Countersunk

Screw 3*10mm Screw 3*12mm Screw 3*12mm

12P

12P '

Plum Blossom

Countersunk Self Tapping

Screw 2 .

3*12mm

69604

69605 69606 69607

IIIII I

IIIII I

IIIII I IIIII I

12P 12P

Plum Blossom

Plum Blossom

Countersunk SelfTapping Countersunk Self Tapping Washer Head Screw

Screw 3*14mm Screw 2.3*7mm 3*4Smm

~~~~~~

12P

Cap Head Hex . Screw

3*10mm

12P

69608 69609 69610 69611

~~~~~~ ~~~~~~

~~~~~~ ~~~~~~

Cap Head SelfTapping

1

Hex. Screw l.S*4mm l ... .. ----

12P

Cap Head Hex. Screw

2*8mm

12P 12P

Washer Head SelfTapping

Screw 2*6mm

--------

·-

----·

Set Screw 4*4mm

NOTES: THE

I~QES

OF THE

PA,~TS

1"\1\Y

VA.R.Y FR,Of'\

YOU~

'---------------------~---------------·---·---

12P i

, 5015

.,

.,

.,

.,

., .,

.,

.,

., .,

12P

5016

Step Set Screw 3*3-2*7

Set Screw 3*3mm

5089 5154

12P

I -·

5018

12P

5038

----

Countersunk Self

12P '

Washer Head Self

Tapping Screw 2 .

6*8mm

1

Tapping Screw 2*9mm

69575

-""""

--

12P 12P

, Washer Head Self Washer Head Hex. Screw Aluminum Suspension

Tapping Screw 2.6*6mm 3*18mm

· - - - · · - - - ·

Mount Assembly

- - - - - · - - - - f - - - - - - -

69569 69578

..

UK Standard

Plug

Li-po Battery Charger+ Li-po Battery Charger+

American Standard Plug UK Standard Plug

- - - - - -

-

- - --......-;

-~

~--

NOTES : THE lf'VI.GES OF THE

P~RTS

1"\1\Y

1/A,~Y F~OII\

YOUR A.CTUA.LLY

~ECEII/ED PA.~TS.

69540

69540

69540

69515

UNITS

~SSEN\BLY-1

69540

69540

H013

69515

STEERINQ SERVO SI\VER

/1\CI(ERfY\1\N PLATE 1\SSE"'BLY

69515

69541

69548

69582

69542

~

69537

H007

6538-H005

6538-H005

3338-TOlO

3338-TOlO

\==69555

~

69555

, \ - 69555

~

~

69540

69540

69541

FINISHED

FRONT/REI\R DIFF.I\SSE"'BLY .

FINISHED

~ H009

69542

NOTES : THE lfo\.6.CiES OF THE

PA,~TS

11\1\Y VA.QY FQ0/1\

YOU~

L-----------------------------------------------------------------------------------~-

69542

UNITS

~SSE/t\BLY-2

CENT~E

DIFF.

~SSEI't\BLY

69513

3338-TOlO

3338-TOlO

\:-:69555 \

,..------~

I\.-

69555

~

69555

~

FINISHED

69542

Screw ( 69595 )

Screw ( 69589 )· ·· · ·············· · · · ···· · ··:

Screw ( 69595 )

CENT~E UNIT/ft\OTO~ ~SSEI't\BLY

FINISHED

NOTES: THE IAAqES OF THE

Pf\~TS

11\1\Y Vf\R.Y

FR_Ofo\

YOU~

/J,CTU/J,LLY R_ECEII/ED P/J,R_TS .

69599

T

69501R

~9599

T69599

I

69599

.....

69544

'

69517

ROLL CAGE ASSEMBLY

69517RB

... ...

69582 69581

.... 69610

69586

...

69586

..

69610

-......

...

---

...

69586

69590

L

69519

69548

H003

69519

P120

; /_

H007

/'

69524R

..

69585

Ty

;~

""

iili ~

69512R

~

6

6

696

69572

69515

~39

---

69538

69584

69510

69584

69519

EXPLODED VIEW

69520

H003

,,

07

......

...

6959 1

69514R

... ...

69591

69525

69526

695>0 oi

H009

""'

~

/

Pl20

69519

0

H003

This product is not a toy. It is not suitable for users under 14 years old unless supervised by an adult .

Never attempt to re-assemble any electronic components. These have been carefully calibrated at the factory.

1/BTH SCALE ELECTRIC POWERED 4WD SAnD RAIL BUGGY

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement