Philips HTS3541 Cinema Home Theatre System User Guide Manual

Register your product and get support at

www.philips.com/welcome

HTS3541

Contents

1 Important

Care for your product

Care for the environment

Help and support

2 Your home theatre

Main unit

Remote control

3 Connect and set up

Connect speakers

5

5

Connect to TV 6

Connect audio from TV and other devices 7

Set up speakers

Set up EasyLink (HDMI-CEC control)

Connect and set up a home network

8

8

9

4 Use your home theatre

Access the home menu

Data fi les

USB storage devices

Audio, video and picture options

MP3 player

YouTube videos

Picasa web albums

Choose sound

10

10

10

11

12

12

13

14

14

14

14

1

1

2

2

2

3

3

3

4

Language settings

Picture and video settings

Audio settings

Display settings

Energy saving settings

Speaker settings

Restore default settings

Update software through USB

Update software through the Internet

18

18

18

18

7 Product

fi

cations

16

17

17

17

17

16

16

16

16

19

8 Troubleshooting

9 Notice

Mains fuse (UK only)

10 Index

21

23

23

23

23

23

24

25

EN 1

1 Important

Read and understand all instructions before you use your product. If damage is caused by failure to follow instructions, the warranty does not apply.

2

Safety

Risk of electric shock or fi re!

• Never expose the product and accessories to rain or water. Never place liquid containers, such as vases, near the product. If liquids are spilt on or into the product, disconnect it from the power socket immediately. Contact

Philips Consumer Care to have the product checked before use.

• Never place the product and accessories near naked fl ames or other heat sources, including direct sunlight.

• Never insert objects into the ventilation slots or other openings on the product.

• Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

• Disconnect the product from the power socket before lightning storms.

• When you disconnect the power cord, always pull the plug, never the cable.

Risk of short circuit or fi re!

• Before you connect the product to the power socket, ensure that the power voltage matches the value printed on the back or bottom of the product. Never connect the product to the power socket if the voltage is different.

Risk of injury or damage to the home theatre!

• For wall-mountable products, use only the supplied wall mount bracket. Secure the wall mount to a wall that can support the combined weight of the product and the wall mount. Koninklijke Philips Electronics N.V. bears no responsibility for improper wall mounting that result in accident, injury or damage.

• For speakers with stands, use only the supplied stands. Secure the stands to the speakers tightly. Place the assembled stands on fl at, level surfaces that can support the combined weight of the speaker and stand.

• Never place the product or any objects on power cords or on other electrical equipment.

• If the product is transported in temperatures below 5°C, unpack the product and wait until its temperature matches room temperature before connecting it to the power socket.

• Visible and invisible laser radiation when open. Avoid exposure to the beam.

• Do not touch the disc optical lens inside the disc compartment.

• Parts of this product may be made of glass.

Handle with care to avoid injury and damage.

Risk of overheating!

• Never install this product in a con fi ned space.

Always leave a space of at least four inches around the product for ventilation. Ensure curtains or other objects never cover the ventilation slots on the product.

Risk of contamination!

• Do not mix batteries (old and new or carbon and alkaline etc.).

• Danger of explosion if batteries are incorrectly replaced. Replace with the same or equivalent type only.

• Remove batteries if they are exhausted or if the remote control is not to be used for a long time.

• Batteries contain chemical substances; they should be disposed of properly.

Risk of swallowing batteries!

• The product/remote control may contain a coin/ button-type battery, which could be swallowed.

Keep the battery out of reach of children at all times! If swallowed, the battery can cause serious injury or death. Severe internal burns can occur within two hours of ingestion.

• If you suspect that a battery has been swallowed or placed inside any part of the body, seek immediate medical attention.

• When you change the batteries, always keep all new and used batteries out of reach of children. Ensure that the battery compartment is completely secure after you replace the battery.

• If the battery compartment cannot be completely secured, discontinue use of the product. Keep out of reach of children and contact the manufacturer.

EN

Care for your product

• Do not insert any objects other than discs into the disc compartment.

• Do not insert warped or cracked discs into the disc compartment.

• Remove discs from the disc compartment if you are not using the product for an extended period of time.

• Use only micro fi bre cloth to clean the product.

Care for the environment

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.

When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002/96/

EC. Please inform yourself about the local separate collection system for electrical and electronic products.

Please act according to your local rules and do not dispose of your old products with your normal household waste.

Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health.

Your product contains batteries covered by the

European Directive 2006/66/EC, which cannot be disposed of with normal household waste.

Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environment and human health.

Help and support

Philips provides extensive online support. Visit our website at www.philips.com/support to:

• download the complete user manual

• print the quick start guide

• watch video tutorials (only available for selected models)

• fi nd answers to frequently answered questions (FAQs)

• email us a question

• chat with our support representative.

Follow the instructions on the website to select your language, and then enter your product model number.

Alternatively, you can contact Philips Consumer

Care in your country. Before you contact Philips, note down the model number and serial number of your product. You can fi nd this information on the back or bottom of your product.

EN 3

2 Your home theatre

Congratulations on your purchase, and welcome to Philips! To fully bene fi t from the support that

Philips offers, register your product at www.philips.

com/welcome.

Main unit

This section includes an overview of the main unit. a Disc compartment b Display panel c ( Open/Close )

Open or close the disc compartment, or eject the disc.

d ( Play/Pause )

Start, pause or resume play.

e SOURCE

Select an audio or video source for the home theatre.

f ( Standby-On )

Switch the home theatre on or to standby.

Connectors

This section includes an overview of the connectors available on your home theatre.

Front connectors

4 a ( USB )

Audio, video or picture input from a USB storage device.

b MUSIC iLINK

Audio input from an MP3 player.

Rear connectors

a AC MAINS

Connect to the power supply.

b SPEAKERS

Connect to the supplied speakers and subwoofer.

c ANTENNA FM

Fixed FM antenna.

d AUDIO IN - AUX

Connect to an analogue audio output on the

TV or an analogue device. e VIDEO OUT

Connect to the composite video input on the TV.

f HDMI OUT (ARC)

Connect to the HDMI input on the TV. g LAN

Connect to the LAN input on a broadband modem or router.

h DIGITAL IN - OPTICAL

Connect to an optical audio output on the

TV or a digital device. i DIGITAL IN - COAXIAL

Connect to a coaxial audio output on the TV or a digital device.

EN

Remote control

EN

This section includes an overview of the remote control.

1

2

3

4

5

6

7

8

9

10

11

12

13 a ( Standby-On )

• Switch the home theatre on or to standby.

• When EasyLink is enabled, press and hold for at least three seconds to switch all connected HDMI CEC compliant devices to standby.

14

15

16

17

18

19

20

21 b ( Home )

Access the home menu.

c Source buttons

• DISC / POP-UP MENU : Switch to disc source. Access or exit the disc menu when you play a disc.

• RADIO : Switch to FM radio.

• AUDIO SOURCE : Select an audio input source.

d BACK

• Return to a previous menu screen.

• In radio mode, press and hold to erase the current preset radio stations.

e Navigation buttons

• Navigate menus.

• In radio mode, press left or right to start auto search.

• In radio mode, press up or down to tune the radio frequency.

f OK

Con fi rm an entry or selection.

g / ( Previous/Next )

• Skip to the previous or next track, chapter or fi le.

• In radio mode, select a preset radio station.

h ( Stop ) / ( Eject / Open/Close )

• Stop play.

• Press and hold for three seconds to open or close the disc compartment, or eject the disc.

i / ( Fast Backward / Fast Forward )

Search backwards or forwards. Press repeatedly to change the search speed.

j +/- ( Volume )

Increase or decrease volume.

k SOUND SETTINGS

Access or exit sound options.

l Alphanumeric buttons

Enter values or letters (using SMS-style entry).

m REPEAT

Select or turn off repeat mode.

n TOP MENU

Access the main menu of a disc.

o OPTIONS

• Access more play options while playing a disc or a USB storage device.

• In radio mode, set a radio station.

5

6 p ( Play )

Start or resume play.

q ( Pause )

Pause play.

r ( Mute )

Mute or restore volume.

s AUDIO

Select an audio language or channel. t SUBTITLE

Select subtitle language for video.

u Colour buttons

Select tasks or options for Blu-ray discs.

3 Connect and set up

This section helps you connect your home theatre to a TV and other devices, and then set it up.

For information about the basic connections of your home theatre and accessories, see the quick start guide. For a comprehensive interactive guide, visit www.connectivityguide.philips.com.

Note

• For identi fi cation and supply ratings, see the type plate at the back or bottom of the product.

• Before you make or change any connections, make sure that all devices are disconnected from the socket.

Connect speakers

The speaker cables are colour-coded for easy connection. To connect a speaker to your home theatre, match the colour on the speaker cable to the colour on the connector.

Speaker position plays a critical role in setting up a surround sound effect. For the best effect, position all the speakers towards the seating area and then place them close to and level with your ears

(when seated).

EN

EN

Note

• Surround sound depends on factors such as room shape and size, type of wall and ceiling, windows and re fl ective surfaces, and speaker acoustics. Experiment with the speaker positions to fi nd the optimum setting for you.

Follow these general guidelines for speaker placement.

1

Seating position:

This is the centre of your listening area.

2

FRONT CENTER (front centre) speaker:

Place the centre speaker directly in front of the seating position, either above or below your TV.

3

FRONT LEFT (front left) and FRONT

RIGHT (front right) speakers:

Place the left and right speakers at the front, and at an equal distance from the centre speaker. Make sure that the left, right and the centre speakers are at an equal distance from your seating position.

4

REAR LEFT (rear left) and REAR RIGHT

(rear right) speakers:

Place the rear surround speakers to the left and right side of your seating position, either in line with it or slightly behind it.

5

SUBWOOFER (subwoofer):

Place the subwoofer at least one metre to the left or right of the TV. Leave about

10-centimetres clearance from the wall.

Connect to TV

Connect your home theatre to a TV to watch videos. You can listen to the TV audio through your home theatre speakers.

Use the best quality connection available on your home theatre and TV.

Option 1: Connect to TV through HDMI

(ARC)

Best quality video

Your home theatre supports HDMI version 1.4 -

Audio Return Channel (ARC). If your TV is HDMI

ARC compliant, you can hear the TV audio through your home theatre by using a single HDMI cable.

1

Using a High-Speed HDMI cable, connect the HDMI OUT (ARC) connector on your home theatre to the HDMI ARC connector on the TV.

• The HDMI ARC connector on the TV might be labelled differently. For details, see the TV user manual.

2

On your TV, turn on HDMI-CEC operations.

For details, see the TV user manual.

• If you cannot hear the TV audio through your home theatre, set up the audio manually (see 'Set up the audio' on page

9 ) .

Option 2: Connect to TV through standard HDMI

TV

Best quality video

If your TV is not HDMI ARC-compliant, connect your home theatre to the TV through a standard

HDMI connection.

1

Using a High-Speed HDMI cable, connect the

HDMI OUT (ARC) connector on your home theatre to the HDMI connector on the TV.

2

Connect an audio cable to hear the TV audio through your home theatre (see 'Connect audio from TV and other devices' on page 7 ) .

3

On your TV, turn on HDMI-CEC operations.

For details, see the TV user manual.

• If you cannot hear the TV audio through your home theatre, set up the audio manually (see 'Set up the audio' on page

9 ) .

Note

• If your TV has a DVI connector, you can use an

HDMI/DVI adapter to connect to TV. However, some of the features may not be available.

7

8

Option 3: Connect to the TV through composite video

TV

Basic quality video

If your TV does not have HDMI connectors, use a composite video connection. A composite connection does not support high-de fi nition video.

1

Using a composite video cable, connect the

VIDEO connector on your home theatre to the VIDEO IN connector on the TV.

• The composite video connector might be labelled AV IN , COMPOSITE or

BASEBAND .

2

Connect an audio cable to hear the TV audio through your home theatre (see 'Connect audio from TV and other devices' on page 7 ) .

3

When you watch TV programmes, press

SOURCE on your home theatre repeatedly to select the correct audio input.

4

When you watch videos, switch your TV to the correct video input. For details, see the

TV user manual.

TV

Connect audio from TV and other devices

Play audio from your TV or other devices through your home theatre speakers.

Use the best quality connection available on your

TV, home theatre and other devices.

Note

• When your home theatre and TV are connected through HDMI ARC, an audio connection is not required (see 'Option 1: Connect to TV through

HDMI (ARC)' on page 6 ) .

Option 1: Connect audio through a digital optical cable

Best quality audio

1

Using an optical cable, connect the OPTICAL connector on your home theatre to the

OPTICAL OUT connector on the TV or other device.

• The digital optical connector might be labelled SPDIF or SPDIF OUT .

TV

Option 2: Connect audio through a digital coaxial cable

Good quality audio

1

Using a coaxial cable, connect the COAXIAL connector on your home theatre to the

COAXIAL/DIGITAL OUT connector on the

TV or other device.

• The digital coaxial connector might be labelled DIGITAL AUDIO OUT .

EN

EN

Option 3: Connect audio through analogue audio cables

Basic quality audio

1

Using an analogue cable, connect the AUX connectors on your home theatre to the

AUDIO OUT connectors on the TV or other device.

Set up speakers

VCR

Manually set up the speakers to experience customised surround sound.

Before you start

Make the necessary connections described in the quick start guide, and then switch the TV to the correct source for your home theatre.

1

Press ( Home ).

2

Select [Setup] , and then press OK .

3

Select [Audio] > [Speaker Setup] .

4

Enter the distance for each speaker, and then listen to the test tones and change the volume. Experiment with the speaker positions to fi nd the ideal setting.

Set up EasyLink (HDMI-CEC control)

This home theatre supports Philips EasyLink, which uses the HDMI-CEC (Consumer Electronics

Control) protocol. EasyLink-compliant devices that are connected through HDMI can be controlled by a single remote control.

Note

• Depending on the manufacturer, HDMI-CEC is known by many names. For information on your device, see the user manual of the device.

• Philips does not guarantee 100% interoperability with all HDMI-CEC devices.

Before you start

• Connect your home theatre to the HDMI-CEC compliant device through a HDMI connection.

• Make the necessary connections described in the quick start guide, and then switch the TV to the correct source for your home theatre.

Enable EasyLink

1

Press ( Home ).

2


3

Select [EasyLink] > [EasyLink] > [On] .

4

On your TV and other connected devices, turn on HDMI-CEC control. For details, see the user manual of the TV or other devices.

• On your TV, set the audio output to

'Ampli fi er' (instead of TV speaker). For details, see the TV user manual.

EasyLink controls

With EasyLink, you can control your home theatre,

TV and other connected HDMI-CEC compliant devices with a single remote control.

• [One Touch Play] (One-touch play): When a video disc is in the disc compartment, press

( Play ) to wake up the TV from standby, and then play a disc.

• [One Touch Standby] (One-touch standby):

If one-touch standby is enabled, your home theatre can switch to standby with the remote control of the TV or other HDMI-CEC devices.

• [System Audio Control] (System audio control):If system audio control is enabled, the audio of the connected device is automatically output through your home theatre speakers when you play the device.

• [Audio Input Mapping] (Audio input mapping): If system audio control does not work, map the connected device to the correct audio input connector on your home theatre (see 'Set up the audio' on page 9 ) .

9

10

Note

• To change the EasyLink control settings, press

( Home ), select [Setup] > [EasyLink] .

Set up the audio

If you cannot hear the audio output of a connected device through your home theatre speakers, check that you have enabled Easylink on all the devices (see 'Enable EasyLink' on page 8 ) .

Then, set up the EasyLink audio control.

1

Press ( Home ).

2


3

Select [EasyLink] > [System Audio Control]

> [On] .

• To play the audio from the TV speakers, select [Off] and skip the following steps.

4

Select [EasyLink] > [Audio Input Mapping] .

5

Follow the onscreen instructions to map the connected device to the audio inputs on your home theatre.

• If you connect your home theatre to the

TV through an HDMI ARC connection, make sure that the TV audio is mapped to the ARC input on your home theatre.

Connect and set up a home network

Connect your home theatre to a home network with Internet access and enjoy:

• YouTube leanback

• Picasa web albums

• BD-Live applications

• Software update

Caution

• Familiarise yourself with the network router and networking principles. If necessary, read documentation that accompanies the network components. Philips is not responsible for lost, damaged or corrupt data.

Before you start

• For software updates, make sure that the network router has access to the Internet with high-speed connection and is not restricted by fi rewalls or other security systems.

• Make the necessary connections described in the quick start guide, and then switch the TV to the correct source for your home theatre.

Set up the wired network

What you need

• A network cable (RJ45 straight cable).

• A network router (with DHCP enabled).

LAN www

1

Using a network cable, connect the LAN connector on your home theatre to the network router.

2

Press ( Home ).

3


4

Select [Network] > [Network Installation]

> [Wired (Ethernet)] .

5

Follow the onscreen instructions to complete the setup.

• If connection fails, select [Retry] , and then press OK .

6

Select [Finish] , and then press OK to exit.

• To view the network settings, select

[Setup] > [Network] > [View Network

Settings] .

EN

4 Use your home theatre

This section helps you use the home theatre to play media from a wide range of sources.

Before you start

• Make the necessary connections described in the Quick start guide and the user manual.

• Switch the TV to the correct source for the home theatre.

Access the home menu

The home menu provides easy access to connected devices, setup and other useful features in your home theatre.

1

Press ( Home ).

» The home menu is displayed.

2

Press the Navigation buttons and OK to select the following:

• [play disc] : Start disc play.

• [Browse USB] : Access the USB content browser

• [Picasa] : Access Picasa web albums.

• [YouTube] : Access YouTube Leanback page.

• [Setup] : Access menus to change video, audio and other settings.

3

Press ( Home ) to exit.

Discs

Your home theatre can play DVDs, VCDs, CDs and Blu-ray discs. It can also play discs that you’ve made at home, such as CD-R discs of photos and music.

1

Insert a disc into the home theatre.

2

If the disc does not play automatically, press

DISC or select [play Disc] from the home menu.

3

Use the remote control to control play (see

'Remote control' on page 4 ) .

• It is normal to hear a slight noise when you play a Blu-ray disc. This does not mean that your home theatre is faulty.

EN

Play buttons

Button

Navigation buttons

Action

Navigate menus.

OK Con fi rm an entry or selection.

( Play ) Start or resume play.

Pause play.

Stop play.

/ Skip to the previous or next track, chapter or fi le.

/ Fast reverse or fast forward. Press repeatedly to change the search speed.

AUDIO Select an audio language or channel.

SUBTITLE Select subtitle language for video.

DISC /

POP-UP

MENU

OPTIONS

Access or exit the disc menu.

Access the advanced options when you play your audio, video or media fi les (see 'Audio, video and picture options' on page 12 ) .

REPEAT Select or turn off repeat mode.

Synchronise picture and sound

If the audio and video are not synchronised, delay the audio to match the video.

1

Press SOUND SETTINGS .

2

Select AUD SYNC , and then press OK .

3

Press the Navigation buttons (up/down) to synchronise the audio with the video.

4

Press OK to con fi rm.

Bonus View on Blu-ray

On Blu-ray discs that support the Bonus View, enjoy extra content such as commentaries in a small screen window. Bonus View is also known as picture-in-picture.

1

Enable Bonus View in the Blu-ray disc menu.

2

While you play the movie, press OPTIONS .

» The options menu is displayed.

3

Select [PIP Selection] > [PIP] .

• Depending on the video, PIP menu [1] or

[2] is displayed.

• To disable Bonus View, select [Off] .

11

4

Select [2nd Audio Language] or [2nd Subtitle

Language] .

5

Select the language, and then press OK .

BD-Live on Blu-ray

Access additional features on the Blu-ray discs with

BD-Live content, such as Internet chats with the director, the latest movie trailers, games, wallpaper and ringtones.

BD-Live services and content vary from disc to disc.

What you need

• Blu-ray disc with BD-Live content

• a USB storage device, with at least 1 GB of memory

1

Connect your home theatre to a home network with Internet access (see 'Connect and set up a home network' on page 9 ) .

2

Connect a USB storage device to your home theatre.

3

Press ( Home ) and select [Setup] .

4

Select [Advanced] > [BD-Live Security] >

[Off] to enable BD-Live.

• To disable BD-Live, select [On] .

5

Select the BD-Live icon in the disc menu, and then press OK .

» BD-Live starts to load. The loading time depends on the disc and your Internet connection.

6

Press the Navigation buttons to navigate BD-

Live, and then press OK to select an option.

Note

• To clear the memory on the storage device, press ( Home ), select [Setup] > [Advanced]

> [Clear Memory] .

Data

fi

les

Your home theatre can play pictures, audio and video fi les contained in a disc or a USB storage device. Before you play a fi le, check that the fi le format is supported by your home theatre (see

'File formats' on page 19 ) .

1

Play the fi les from a disc or USB storage device.

12

2

To stop play, press .

• To resume the video from where you stopped, press ( Play ).

• To play the video from the start, press OK .

Note

• To play DivX DRM protected fi les, connect your home theatre to a TV through an HDMI cable.

Subtitles

If your video has subtitles in multiple languages, select a subtitle language.

Note

• Make sure that the subtitle fi le has exactly the same name as the video fi le. For example, if the video fi le is named 'movie.avi', name the subtitle fi le 'movie.srt' or 'movie.sub'.

• Your home theatre supports the following fi le formats: .srt, .sub, .txt, .ssa, .ass, smi and .sami. If the subtitles do not appear correctly, change the character set.

1

While playing video, press SUBTITLE to select a language.

2

For DivX videos, if the subtitles do not appear correctly, continue with the following steps to change the character set.

3

Press OPTIONS .

» The options menu is displayed.

4

Select [Character Set] , and then select a character set that supports the subtitles.

Europe, India and Russia

Character

Set

Language

[Standard] English, Albanian, Danish, Dutch, Finnish,

French, Gaelic, German, Italian, Kurdish

(Latin), Norwegian, Portuguese, Spanish,

Swedish and Turkish

[Central

Europe]

Albanian, Croat, Czech, Dutch, English,

German, Hungarian, Irish, Polish,

Romanian, Slovak, Slovene and Sorbian

[Cyrillic] Bulgarian, Belorussian, English,

Macedonian, Moldavian, Russian,

Serbian and Ukrainian

[Greek] Greek

EN

VOD code for DivX

Before you purchase DivX videos and play them on your home theatre, register the home theatre on www.divx.com using the DivX VOD code.

1

Press ( Home ).

2


3

Select [Advanced] > [DivX® VOD Code] .

» The DivX VOD registration code for your home theatre is displayed.

USB storage devices

Enjoy pictures, audio and video stored on a USB storage device such as an MP4 player or digital camera.

What you need

• A USB storage device that is formatted for

FAT or NTFS fi le systems and complies with the Mass Storage Class.

• A media fi le in one of the supported fi le formats (see 'File formats' on page 19 ) .

Note

• If you use a USB extension cable, USB HUB or

USB multi-reader, the USB storage device may not be recognised.

1

Connect a USB storage device to the

( USB ) connector on your home theatre.

2

Press ( Home ).

3

Select [browse USB] , and then press OK .

» A content browser is displayed.

4

Select a fi le, and then press OK .

5

Press the play buttons to control play (see

'Play buttons' on page 10 ) .

Audio, video and picture options

Use advanced features when you play pictures, audio and video fi les from a disc or a USB storage device.

Audio options

While playing audio, repeat an audio track, a disc or a folder.

1

Press OPTIONS repeatedly to cycle through the following functions:

• RPT TRACK / RPT FILE : Repeat the current track or fi le.

• RPT DISC / RPT FOLDER : Repeat all the tracks on the disc or the folder.

• RPT RANDOM : Play audio tracks in random order.

• RPT OFF : Turn off the repeat mode.

Video options

While watching video, select options such as subtitles, audio language, time search and picture settings. Depending on the video source, some options are not available.

1

Press OPTIONS .

» The video options menu is displayed.

2

Press the Navigation buttons and OK to select and change:

• [Audio Language] : Select audio language for video.

• [Subtitle Language] : Select subtitle language for video.

• [Subtitle Shift] : Change the subtitle position on the screen.

• [Info] : Display information about what is playing.

• [Character Set] : Select a character set that supports the DivX subtitle.

• [Time Search] : Skip to a speci fi c part of the video by entering the time of the scene.

• [2nd Audio Language] : Select the second audio language for Blu-ray video.

• [2nd Subtitle Language] : Select the second subtitle language for Blu-ray video.

• [Titles] : Select a speci fi c title.

• [Chapters] : Select a speci fi c chapter.

• [Angle List] : Select a different camera angle.

• [Menus] : Display the disc menu.

• [PIP Selection] : Display Picture-in-Picture window when playing a Blu-ray disc that supports the Bonus View.

• [Zoom] : Zoom into a video scene or picture. Press the Navigation buttons

(left/right) to select a zoom factor.

• [Repeat] : Repeat a chapter or title.

EN 13

• [Repeat A-B] : Mark two points within a chapter or track to repeat play, or turn off the repeat mode.

• [Picture Settings] : Select a prede fi ned colour setting.

Picture options

While viewing a picture, zoom into the picture, rotate it, add animation to a slideshow and change the picture settings.

1

Press OPTIONS .

» The picture options menu appears.

2

Press the Navigation buttons and OK to select and change the following settings:

• [Rotate +90] : Rotate the picture 90 degrees clockwise.

• [Rotate -90] : Rotate the picture 90 degrees anti-clockwise.

• [Zoom] : Zoom into a video scene or picture. Press the Navigation buttons

(left/right) to select a zoom factor.

• [Info] : Display picture information.

• [Duration per slide] : Select the display speed for each picture in a slide show.

• [Slide Animation] : Select animation for the slideshow.

• [Picture Settings] : Select a prede fi ned colour setting.

• [Repeat] : Repeat a selected folder.

Musical slideshow

If the picture and audio fi les are from the same disc or USB storage device, you can create a musical slideshow.

1

Select an audio track, and then press OK .

2

Press BACK , and go to the picture folder.

3

Select a picture, and then press ( Play ) to start the slideshow.

4

Press to stop slideshow.

5

Press again to stop music.

Note

• Make sure that the picture and audio formats are supported by your home theatre (see 'File formats' on page 19 ) .

Radio

Listen to FM radio on your home theatre, and store up to 40 radio stations.

Note

• AM and digital radio are not supported.

• If no stereo signal is detected, or if fewer than fi ve stations are found, you are prompted to install the radio stations again.

1

Extend the FM antenna at the back of your home theatre and place it away from the TV or other sources of radiation.

2

Press RADIO .

» If you have already installed the radio stations, the last channel that you listened to is played.

» If you have not installed any radio stations, the message

AUTO

INSTALL...PRESS PLAY

appears on the display panel. press (

Play

).

3

Use the remote control to listen or to change radio stations.

Button

/

or

Alphanumeric buttons

Navigation buttons

Action

Select a preset radio station.

BACK

OPTIONS

Left/Right: Search for a radio station.

Up/Down: Fine tune a radio frequency.

Press to stop the installation of radio stations.

Press and hold to erase the preset radio station.

Manual:

1) Press OPTIONS . 2)

Press / to select your preset. 3) Press OPTIONS again to store the radio station.

Automatic: Press and hold for three seconds to reinstall the radio stations.

14 EN

MP3 player

Connect an MP3 player to play audio fi les.

What you need

• An MP3 player.

• A 3.5-mm stereo audio cable.

1

Using the 3.5 mm stereo audio cable, connect the MP3 player to the MUSIC iLINK connector on your home theatre.

2

Press AUDIO SOURCE repeatedly until

MUSIC I-LINK appears on the display panel.

3

Press the buttons on the MP3 player to select and play audio fi les.

YouTube videos

Enjoy YouTube videos through your home theatre.

1

Connect your home theatre to a home network with a high-speed Internet access

(see 'Connect and set up a home network' on page 9 ) .

2

Press ( Home ).

3

Select [YouTube] , and then press OK .

» The YouTube Leanback page is displayed.

4

Follow the onscreen instructions to browse the YouTube page.

5

Use the remote control to select and navigate the application.

Button

Navigation buttons

Action

Up: Access the onscreen keyboard.

Down: Access the onscreen playback buttons.

Left/Right: Select a video from the playlist.

• If you do not press a button within few seconds, the onscreen buttons and menu exit automatically.

6

Press ( Home ) to exit the YouTube page.

Picasa web albums

Access Picasa Web Albums through your home theatre.

What you need

• An account with Picasa Web Albums.

1

Connect your home theatre to a home network with Internet access (see 'Connect and set up a home network' on page 9 ) .

2

Press ( Home ).

3

Select [Picasa] , and then press OK .

4

Log in to your Picasa web account.

• The fi rst time you log in, select [New user] , and then enter your username and password. Save your login information for subsequent use.

• If you have logged in before, select a stored username and enter the password.

5

Select the onscreen options to view the albums or photos.

6

Press ( Home ) to exit Picasa menu.

View slideshow

1

Select [My photos] from the Picasa menu, and then press OK .

» The photo albums in your Picasa Web

Albums are displayed.

2

Select a photo, and then press OK to view the photo in full screen.

3

Press OK again to view the photos in a slideshow.

4

While viewing a slideshow, press OPTIONS to access more play options.

5

Press BACK to return to the previous screen.

Choose sound

This section helps you choose the ideal sound for your video or music.

1


2

Press the Navigation buttons (left/right) to access the sound options on the display.

EN 15

Sound settings Description

SOUND

TREBLE

Select a sound mode.

SURROUND Select surround sound or stereo sound.

Change the high frequency output.

MID Change the middle frequency output.

BASS Change the low frequency output.

AUD SYNC Delay the audio to match the video.

3

Select an option, and then press OK .

4

Press BACK to exit.

If you do not press a button within a minute, the menu exits automatically.

Sound mode

Select prede fi ned sound modes to suit your video or music.

1


2

Select SOUND , and then press OK .

3

Press the Navigation buttons (up/down) to select a setting on the display:

• MOVIE : Enjoy a cinematic audio experience, specially enhanced for movies.

• MUSIC : Recreate the original recording environment of your music, in the studio or at a concert.

• ORIGINAL : Experience the original sound of your movies and music, without added sound effects.

• NEWS : Hear every word with optimised speech and clear vocals.

• GAMING : Enjoy thrilling arcade sounds, ideal for action-packed video games or loud parties.

4


Surround sound mode

Experience an immersive audio experience with surround sound modes.

1


2

Select SURROUND , and then press OK .

3

Press the Navigation buttons (up/down) to select a setting from your display:

• AUTO : Surround sound based on the audio stream.

• 5CH STER : Enhanced stereo sound. Ideal for party music.

• MULTI-CH : Immersive multi-channel sound for an enhanced movie experience.

• STEREO : Two-channel stereo sound. Ideal for listening to music.

4


Equalizer

Change the high frequency (treble), mid frequency

(mid) and low frequency (bass) settings of the home theatre.

1


2

Select TREBLE , MID or BASS , and then press

OK .

3

Press the Navigation buttons (up/down) to change the frequency.

4


16 EN

The home theatre settings are already con fi gured for optimal performance. Unless you have a reason to change a setting, we recommend that you keep the default setting.

Note

• You cannot change a setting that is greyed out.

• To return to the previous menu, press

BACK . To exit the menu, press ( Home ).

4


• [TV Display] : Select a picture format to fi t the TV screen.

• [HDMI Video] : Select the resolution of the video signal that is output from HDMI OUT

(ARC) on your home theatre. To enjoy the selected resolution, make sure that your TV supports the selected resolution.

• [HDMI Deep Color] : Recreate the natural world on your TV screen by displaying vivid images using billions of colours. Your home theatre must be connected to a Deep

Color enabled TV through an HDMI cable.

• [Picture Settings] : Select pre-de fi ned colour settings for the video display.

• [Watch 3D video] : Set HDMI video to support 3D or 2D video.

Note

• If you change a setting, make sure that the TV supports the new setting.

Language settings

1

Press ( Home ).

2


3

Select [Preference] , and then press OK .

4


• [Menu Language] : Select a display language for the menu.

• [Audio] : Select an audio language for the discs.

• [Subtitle] : Select a subtitle language for the discs.

• [Disc Menu] : Select a menu language for the discs.

Note

• If your preferred disc language is not available, select [Others] from the list and enter the

4-digit language code found at the end of this user manual .

• If you select a language that is not available on a disc, the home theatre uses the default language of the disc.

Picture and video settings

1

Press ( Home ).

2


3

Select [Video] , and then press OK .

EN

Audio settings

1

Press ( Home ).

2


3

Select [Audio] , and then press OK .

4


• [Night Mode] : For quiet listening, decrease the volume of loud sounds on your home theatre. Night mode is only available for Dolby-encoded DVD and

Blu-ray discs.

• [HDMI Audio] : Set the HDMI audio output from your TV, or disable HDMI audio output from the TV.

• [Default sound settings] : Restore the equaliser settings of all the sound modes to the default values.

Parental control settings

1

Press ( Home ).

2


17

3


4


• [Change Password] : Set or change your password for parental control access.

If you do not have a password or have forgotten your password, enter 0000 .

• [Parental Control] : Restrict access to discs that are recorded with age ratings.

To play all discs, irrespective of the ratings, select 8 or [Off] .

Display settings

1

Press ( Home ).

2


3


4


• [Auto Subtitle Shift] : Enable or disable automatic repositioning of subtitles on

TVs that support this feature.

• [Display Panel] : Set the brightness of the home theatre front panel display.

• [VCD PBC] : Enable or disable the content menu navigation of VCD and SVCD discs with Play Back Control feature.

Energy saving settings

1

Press ( Home ).

2


3


4


• [Screen Saver] : Switch the home theatre to screen saver mode after 10 minutes of inactivity.

• [Auto Standby] : Switch the home theatre to standby after 30 minutes of inactivity.

This timer only works when a disc or

USB play is paused or stopped.

• [Sleep Timer] : Set the duration of the sleep timer so that the home theatre is switched to standby after the speci fi ed period.

Speaker settings

1

Press ( Home ).

2


3

Select [Advanced] , and then press OK .

4


• [Enhanced Audio] : Select [On] to enable audio post processing on the speaker and enable karaoke settings (if your product supports Karaoke). To play the original audio of the disc, select [Off] .

Tip

• Enable audio post processing before you select a prede fi ned sound mode (see 'Sound mode' on page

15 ) .

Restore default settings

1

Press ( Home ).

2


3

Select [Advanced] > [Restore Default

Settings] , and then press OK .

4

Select [OK] , and then press OK to con fi rm.

» Your home theatre is reset to its default settings except for some settings, such as parental control and DivX VOD registration code.

18 EN

Philips continually tries to improve its products.

To get the best features and support, update your home theatre with the latest software.

Compare the version of your current software with the latest version on www.philips.com/support. If the current version is lower than the latest version available on the Philips support website, upgrade your home theatre with the latest software.

Caution

• Do not install a lower version of software than the version currently installed on your product.

Philips is not liable for problems caused due to software downgrading.

Check software version

Check the version of the software currently installed on your home theatre.

1

Press ( Home ).

2


3

Select [Advanced] > [Version Info.] , and then press OK .

» The software version is displayed.

Update software through USB

What you need

• A USB fl ash drive that is FAT or NTFSformatted, with at least 75 MB of memory.

Do not use a USB hard drive.

• A computer with Internet access.

• An archive utility that supports the ZIP fi le format.

Step 1: Download the latest software

1

Connect a USB fl ash drive to your computer.

2

In your web browser, go to www.philips.com/ support.

3

At the Philips Support website, fi nd your product and locate the Software and drivers .

» The software update is available as a zip fi le.

EN

4

Save the zip fi le in the root directory of your

USB fl ash drive.

5

Use the archive utility to extract the software update fi le in the root directory.

» The fi les are extracted in the UPG_ALL

folder on your USB fl ash drive.

6

Disconnect the USB fl ash drive from your computer.

Step 2: Update the software

Caution

• Do not switch off the home theatre or remove the USB fl ash drive during the update.

1

Connect the USB fl ash drive containing the downloaded fi le to your home theatre.

• Make sure that the disc compartment is closed and that there is no disc inside.

2

Press ( Home ).

3


4

Select [Advanced] > [Software Update] > [USB] .

5

Follow the onscreen instructions to con fi rm the update.

» Once complete, the home theatre automatically switches off and restarts. If it does not, disconnect the power cord for a few seconds and then reconnect it.

Update software through the

Internet

1

Connect your home theatre to a home network with a high-speed Internet access (see 'Connect and set up a home network' on page 9 ) .

2

Press ( Home ).

3


4

Select [Advanced] > [Software Update] >

[Network] .

» If upgrade media is detected, you are prompted to start or cancel the update.

5

Follow the onscreen instructions to con fi rm the update.

» Once complete, the home theatre automatically switches off and restarts. If it does not, disconnect the power cord for a few seconds and then reconnect it.

19

7 Product specifications

Note

• Speci fi cations and design are subject to change without notice.

Region codes

The type plate on the back or bottom of the home theatre shows which regions it supports.

Country

Europe,

United Kingdom

Asia Pacific, Taiwan,

Korea

Latin America

Australia,

New Zealand

Russia, India

China

Media formats

• AVCHD, BD, BD-R/ BD-RE, BD-Video,

DVD-Video, DVD+R/+RW, DVD-R/-RW,

DVD+R/-R DL, CD-R/CD-RW, Audio CD,

Video CD/SVCD, Picture fi les, MP3 media,

WMA media, DivX Plus HD media, USB storage device

DVD BD

File formats

• Audio: .aac, .mka, .mp3, .wma, .wav

• Video: .avi, .divx, .mp4, .mkv, .asf, .mpg, .mpeg

• Picture: .jpg, .jpeg, .gif, .png

20

Audio formats

Your home theatre supports the following audio fi les.

Extension Container Audio codec

.mp3

.wma

.aac

.wav

.m4a

.mka

.mka

.mka

.mka

.mka

.mka

.mka

MP3

ASF

AAC

WAV

MKV

MKA

MKA

MKA

MKA

MKA

MKA

MKA

MP3

WMA

Bit rate

32 kbps ~

320 kbps

64 kbps ~

160 kbps

192 kbps AAC, HE-

AAC

PCM

AAC

WMA

AAC,

HE-AAC

1.4 Mbps

192 kbps

PCM

Dolby

Digital

27.648

Mbps

640 kbps

DTS core 1.54 Mbps

MPEG

MP3

912 kbps

32 kbps ~

320 kbps

64 kbps ~

160 kbps

192 kbps

Video formats

If you have a high de fi nition TV, your home theatre allows you to play your video fi les with:

• Resolution: 1920 x 1080 pixels at

• Frame rate: 6–30 frames per second.

.avi fi les in AVI container

Audio codec Video codec

PCM, Dolby

Digital, DTS core, MP3,

WMA

DivX 3.11,

DivX4.x, DivX5.x,

DivX6.x

Bit rate

10 Mbps max

MPEG 1, MPEG 2 20 Mbps

(peak

40 Mbps)

MPEG 4 ASP 10 Mbps max

H.264/AVC

[email protected]/4.0;

[email protected]/3.1/3.0

20 Mbps

(peak

40 Mbps)

EN

.divx fi les in AVI container

Audio codec

PCM,

Dolby

Digital,

MP3,

WMA

Video codec

DivX 3.11,

DivX4.x, DivX5.x,

DivX6.x

Bit rate

10 Mbps max

MPEG 1, MPEG 2

MPEG 4 ASP

.mp4 or .m4v fi les in MP4 container

20 Mbps

(peak

40 Mbps)

10 Mbps max

Bit rate Audio codec

Dolby

Digital,

MPEG,

MP3, AAC,

HE-AAC

Video codec

MPEG 1, MPEG

2

MPEG 4 ASP

H.264/AVC



.mkv fi les in MKV container

20 Mbps (peak

40 Mbps)

10 Mbps max

20 Mbps (peak

40 Mbps)

Audio codec

PCM, Dolby Digital,

DTS core, MPEG,

MP3, WMA, AAC,

HE-AAC

Video codec

MPEG 1, MPEG

2

MPEG 4 ASP

H.264/AVC



Bit rate

20 Mbps

(peak

40 Mbps)

10 Mbps max

20 Mbps

(peak

40 Mbps)

Ampli

fi

er

• Total output power: 300 W RMS (30% THD)

• Frequency response: 20 Hz-20 kHz / ±3 dB

• Signal-to-noise ratio: > 65 dB (CCIR)/

(A-weighted)

• Input sensitivity:

• AUX: 2 V

• Music iLink: 1 V

EN

Video

• Signal system: PAL/NTSC

• HDMI output: 480i/576i, 480p/576p, 720p,

1080i, 1080p, 1080p24

Audio

• S/PDIF Digital audio input:

• Coaxial: IEC 60958-3

• Optical: TOSLINK

• Sampling frequency:

• MP3: 32 kHz, 44.1 kHz, 48 kHz

• WMA: 44.1 kHz, 48 kHz

• Constant bit rate:

• MP3: 32 kbps - 320 kbps

• WMA: 48 kbps - 192 kbps

Radio

• Tuning range:

• Europe/Russia/China: FM 87.5-108 MHz

(50 kHz)

• Asia Paci fi c/Latin America: FM 87.5-

108 MHz (50/100 kHz)

• Signal-to-noise ratio: FM 50 dB

• Frequency response: FM 200 Hz-12.5 kHz /

±6 dB

USB

• Compatibility: Hi-Speed USB (2.0)

• Class support: USB Mass Storage Class

(MSC)

• File system: FAT16, FAT32, NTFS

• Maximum memory support: < 160 GB

Main unit

• Power supply:

• Europe/China/Russia/India: 220-240 V~,

50 Hz

• Latin America/Asia Paci fi c: 110-240 V~,

50-60 Hz

• Power consumption: 60 W

• Standby power consumption: ≤ 0.9 W

• Dimensions (WxHxD): 360 x 58 x 325 mm

• Weight: 2.4 kg

21

Subwoofer

• Output power: 50 W RMS (30% THD)

• Impedance: 4 ohm

• Speaker drivers: 133 mm (5.25") woofer

• Dimensions (W x H x D): 160 x 265 x

265 mm

• Weight: 2.50 kg

Speakers

Centre speaker:

• Output power: 50 W RMS (30% THD)

• Speaker impedance: 4 ohm

• Speaker drivers: 1 x 63.5 mm (2.5") woofer

• Dimensions (W x H x D): 159 x 84.5 x

80 mm

• Weight: 0.35 kg

Front/Rear speaker:

• Output power: 4 x 50 W RMS (30% THD)

• Speaker impedance: 4 ohm

• Speaker drivers: 1 x 63.5 mm (2.5") woofer

• Dimensions (WxHxD): 84.5 x 159 x 80 mm

• Weight: 0.35 kg/each

Remote control batteries

• 2 x AAA-R03-1.5 V

Laser

• Laser Type (Diode): InGaN/AlGaN (BD),

AlGaInP (DVD/CD)

• Wave length: 405 +7 nm/-7 nm (BD), 655

+10 nm/-10 nm (DVD), 790 +10 nm/-20 nm

(CD)

• Output power (Max. ratings): 20 mW (BD),

6 mW (DVD), 7 mW (CD)

8 Troubleshooting

Warning

• Risk of electric shock. Never remove the casing of the product.

To keep the warranty valid, never try to repair the product yourself.

If you have problems using this product, check the following points before you request service. If you are still having problems, get support at www.

philips.com/support.

Main unit

The buttons on the home theatre do not work.

• Disconnect the home theatre from the power supply for a few minutes, then reconnect.

Picture

No picture.

• Make sure that the TV is switched to the correct source for the home theatre.

No picture on a TV connected through HDMI.

• Make sure that the HDMI cable is not faulty. If it is faulty, replace it with a new cable.

• Press ( Home ) and then 731 on the remote control to restore the default picture resolution.

• Change the HDMI video setting, or wait for

10 seconds for auto recovery (see 'Picture and video settings' on page 16 ) .

Disc does not play high-de fi nition video.

• Make sure that the disc contains highde fi nition video.

• Make sure that the TV supports highde fi nition video.

• Use an HDMI cable to connect to the TV.

22 EN

Sound

No sound from home theatre speakers.

• Connect the audio cable from your home theatre to your TV or other devices. You do not need a separate audio connection when the home theatre and TV are connected through an HDMI ARC connection.

• Set up the audio for the connected device

(see 'Set up the audio' on page 9 ) .

• Reset your home theatre to its factory settings

(see 'Restore default settings' on page 17 ) , then switch it off and switch on again.

• On your home theatre, press SOURCE repeatedly to select the correct audio input.

Distorted sound or echo.

• If you play audio from the TV through the home theatre, make sure that the TV is muted.

Audio and video are not synchronised.

• 1) Press SOUND SETTINGS . 2) Press the Navigation buttons (left/right) to select

AUD SYNC , and then press OK . 3) Press the Navigation buttons (up/down) to synchronise the audio with the video.

Play

Cannot play a disc.

• Clean the disc.

• Make sure that the home theatre supports the type of disc (see 'Media formats' on page 19 ) .

• Make sure that the home theatre supports the region code of the disc .

• If the disc is a DVD±RW or DVD±R disc, make sure that it is fi nalised.

Cannot play a DivX fi le.

• Make sure that the DivX fi le is encoded according to the 'Home Theatre Pro fi le' with the DivX encoder.

• Make sure that the DivX fi le is complete.

DivX subtitles do not display correctly.

• Make sure that the subtitle fi le name is the same as the movie fi le name (see 'Subtitles' on page 11 ) .

• Select the correct character set: 1) Press

OPTIONS . 2) Select [Character Set] . 3) Select the supported character set. 4) Press OK .

Cannot read the contents of a USB storage device.

• Make sure that the format of the USB storage device is compatible with the home theatre.

• Make sure that the fi le system on the USB storage device is supported by the home theatre.

'No entry' or 'x' sign appears on the TV.

• The operation is not possible.

EN

EasyLink does not work.

• Make sure that the home theatre is connected to a Philips brand EasyLink TV, and the EasyLink option is turned on (see 'Set up

EasyLink (HDMI-CEC control)' on page 8 ) .

When you switch on the TV, the home theatre automatically switches on.

• This behaviour is normal when you are using

Philips EasyLink (HDMI-CEC). To make the home theatre work independently, switch off EasyLink.

Cannot access BD-Live features.

• Make sure that the home theatre is connected to a home network with Internet access (see 'Connect and set up a home network' on page 9 ) .

• Make sure that the network is set up (see

'Set up the wired network' on page 9 ) .

• Make sure that the Blu-ray disc supports BD-

Live features.

• Clear memory storage (see 'BD-Live on Bluray' on page 11 ) .

TV screen is black when you play a Blu-ray video or a DivX copy protected video.

• Make sure that the home theatre is connected to the TV through an HDMI cable.

• Switch to the correct HDMI source on the

TV.

Poor playback on YouTube Leanback or Picasa.

• Make sure that the home theatre is connected to a home network and is properly set up (see 'Connect and set up a home network' on page 9 ) .

• Make sure that the Internet connection speed is higher than 2 MBPS to obtain optimum performance.

23

9 Notice

This section contains the legal and trademark notices.

Copyright

This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation.

Reverse engineering and disassembly are prohibited.

Copyright in the UK

Recording and playback of material may require consent. See Copyright Act 1956 and The

Performers' Protection Acts 1958 to 1972.

24

Compliance

This product is in compliance with the essential requirements and other relevant provisions of Directives 2006/95/EC (Low Voltage) and

2004/108/EC (EMC).

This product incorporates proprietary technology under license from Verance Corporation and is protected by U.S. Patent 7,369,677 and other

U.S. and worldwide patents issued and pending as well as copyright and trade secret protection for certain aspects of such technology. Cinavia is a trademark of Verance Corporation. Copyright

2004-2010 Verance Corporation. All rights reserved by Verance. Reverse engineering or disassembly is prohibited.

Cinavia notice

This product uses Cinavia technology to limit the use of unauthorized copies of some commerciallyproduced fi lm and videos and their soundtracks.

When a prohibited use of an unauthorized copy is detected, a message will be displayed and playback or copying will be interrupted.

More information about Cinavia technology is provided at the Cinavia Online Consumer

Information Center at http://www.cinavia.com. To request additional information about Cinavia by mail, send a postcard with your mailing address to:

Cinavia Consumer Information Center, P.O. Box

86851, San Diego, CA, 92138, USA.

Mains fuse (UK only)

This information applies only to products with a

UK mains plug.

This product is fi tted with an approved moulded plug. If you replace the fuse, use one with:

• the ratings shown on the plug,

• a BS 1362 approval, and

• the ASTA approval mark.

Contact your dealer if you are not sure about what type of fuse to use.

Caution: To comply with the EMC directive

(2004/108/EC), do not detach the plug from the power cord.

Open source software

Philips Electronics Singapore Pte Ltd hereby offers to deliver, upon request, a copy of the complete corresponding source code for the copyrighted open source software packages used in this product for which such offer is requested by the respective licences. This offer is valid up to three years after product purchase to anyone in receipt of this information. To obtain the source code, please contact [email protected]. If you prefer not to use email, or if you do not receive a con fi rmation receipt within a week of mailing this email address, please write to "Open Source Team,

Philips Intellectual Property & Standards, P.O. Box

220, 5600 AE Eindhoven, The Netherlands". If you do not receive timely con fi rmation of your letter, please send an email to the email address above.

The texts of the licences and acknowledgements for open source software used in this product are included on a separate lea fl et.

EN

EN

Trademarks

"Blu-ray Disc", "Blu-ray" and "Blu-ray Disc" logo are trademarks of Blu-ray Disc Association.

Java and all other Java trademarks and logos are trademarks or registered trademarks of Sun

Microsystems, Inc. in the United States and/or other countries.

Manufactured under licence under U.S. Patent

Nos.: 5,956,674; 5,974,380; 6,226,616; 6,487,535;

7,392,195; 7,272,567; 7,333,929; 7,212,872 and other U.S. and worldwide patents issued & pending. DTS-HD, the Symbol and DTS-HD and the Symbol together are registered trademarks, and DTS-HD Master Audio | Essential is a trademark of DTS, Inc. Product includes software.

DTS, Inc. All Rights Reserved.

Manufactured under licence from Dolby

Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668; 7,515,710; 7,519,274.

DivX®, DivX Certi fi ed®, DivX Plus® HD and associated logos are trademarks of Rovi

Corporation or its subsidiaries and are used under licence.

ABOUT DIVX PLUS® HD: DivX® is a digital video format created by DivX, Inc. This is an of fi cial

DivX Certi fi ed® device that plays DivX video, including DivX® Plus HD video (H.264/.MKV) up to 1080p and premium content. Visit www.divx.

com for more information and software tools to convert your fi les into DivX video.

ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi

Corporation. This is an of fi cial DivX Certi fi ed® device that plays DivX video. Visit divx.com for more information and software tools to convert your fi les into DivX videos.

ABOUT DIVX VIDEO-ON-DEMAND: This DivX

Certi fi ed® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the

DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration.

HDMI, the HDMI logo and High-De fi nition

Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC in the United

States and other countries.

CLASS 1

LASER PRODUCT

25

10 Index

2

2nd audio language

2nd subtitle language

5

5.1 speakers

A

advanced settings

ampli fi er

audio connection (analogue cable)

audio connection (coaxial cable)

audio connection (HDMI ARC)

audio connection (optical cable)

audio formats

audio from other devices

audio input mapping

audio language

audio options

audio post processing

audio settings

audio setup

auto standby

auto subtitle shift

B

batteries

BD-Live

Blu-ray

Bonus View

brightness

C

change password

character set

clear BD-Live memory

connect to TV

connectors

control buttons (disc)

control buttons (USB)

copyright protection

customer support

26

10

10

5

21

11

10

10

17

3

10

10

23

2

16

11

11

6

16

9

17

17

9

16

12

17

6

7

19

7

17

20

8

7

D

data fi les

deep color

default settings

disc language

disc menu

display panel

disposal

DivX

E

Easylink (HDMI-CEC)

eject disc

enhanced audio

environment

F

factory settings

FAQs fi le formats

H

HDMI ARC

HDMI audio

HDMI-CEC

home menu

home network

I

Internet

M

main unit

manual setup

media formats

menu language

MP3

musical slideshows

N

network

night mode

EN

17

2

19

3

8

19

16

14

13

9

16

6

16

8

10

9

9

16

17

2

11

11

16

17

16

8

3

17

2

O

one-touch play

one-touch standby

options

P

parental control

PBC (play back control)

Picasa web albums

picture options

picture resolution

picture settings

picture-in-picture

play disc

play music

play radio

play USB storage device

power settings

pre-de fi ned sound mode

preference

programme radio stations

R

radio

recycling

region codes

remote control

repeat

S

shuf fl e

sleep timer

slide animation

software update

software version

sound

speaker position

speaker setup

speaker speci fi cations

subtitle language

subtitle position

surround sound

synchronise picture and sound

system audio control

8

8

12

13

2

19

4

12

14

13

12

17

15

16

13

16

16

10

10

16

17

14

13

19

16

17

15

10

9

18

14

5

8

12

17

13

18

T

troubleshooting (picture)

troubleshooting (play)

troubleshooting (sound)

tune radio stations

U

update software (through Internet)

update software (through USB)

USB storage device

user manual

V

VCD

video connection (composite video)

video connection (HDMI ARC)

video connection (standard HDMI)

video formats

video options

video settings

VOD code (DivX)

W

wired network

Y

YouTube videos

21

22

22

13

18

18

12

2

20

12

16

12

17

7

6

6

9

14

EN 27

28 EN

book1 indd

Language Code

boo

© 201 2 Koninklijke Philips Electronics N.V.

All rights reserved.

sgpjp_1 210 / 12 _ MKII_ v 1

No results