advertisement
▼
Scroll to page 2
of 7
7x10W 4IN1 Indoor Par Light User Manual Introduction Welcome to use High Power 4IN1 Indoor LED PAR Light under Neo-Neon Brand, This fixture applies high power LED technology and enjoys long life span. It can work in DMX, Manual, Auto, Sound and Linkable modes. It is also user-friendly, which makes it suitable for all kinds of entertainment and decorative industries. The fixture can be used as a single unit or a PAR Light Set (4 PCS or 4*N PCS) Packing Listing 1. IRDIP-9007456-01D-13 7x10W 4IN1 Indoor Par Light -----One 2.User Manual ------------------------------------- One 3.Power Cable ----------------------------------------- One 4.DMX Cable -------------------------------------------- One 1/ 7 Specification 1.Voltage: 110V~240V/50~60Hz 5.Connector: DMX512(3 PINS XLR) 2.Power Consumption:71W(max) 6.Weight: 2.1kg 3.Light Source: 7 *10W 4IN1 LED 7. Dimension:L150 X W213 X H203 4.Working Modes:DMX,Auto,Manual,Sound,Master/Slave Caution z Read the user manual before use and follow the instruction z Please connect the fixture to the earth linked power supply and be sure that it is the same as the rating voltage on the fixture z The fixture is pack without any spare part. Please contact the manufacturer when maintenance is needed. z Please note that the working temperature is between -20℃ and 40℃ z Please contact the professional engineers for repair. Addition: If the power sockets is not earth linked, please add the grounding connection to the housing of the fixture, so as to avoid the damage from the accumulated static or charge. PAR Light Setting 1.Five Working Modes : 1 Auto— Run the internal program automatically 4、DMX512—— DMX control Mode 5、4 Channels Mode-—— Run under the control by 2、Manual——Run the program manually 3、Sound —— Run the internal program by sound 4-Channels controller 2. Key Pressing and Digital Tube Setting 2-1、 Operation Panel as Picture 2 shows MENU UP DOWN ENTER Picture 3 Picture 2 2-2、Instruction on Digital Tube As Picture Three shows, it shows in 4 Digits and 8 Segments format 2-3、Function Setting and Display Instruction The fixture has memory function. After powered on to enter DMX mode, it shows “A001” at the first time. In the following use, the fixture will enter the previous modes directly. Press the keys on the operation panel to choose different working modes. Hereunder is the details. “MENU”Button Modes Tube Display “ENTER” Button Parameter DMX Mode A*** Modification “UP”Button “DOWN”Button A.001-A.512 (DMX address setting) A.001-A.512 (DMX Address Setting) Par.0-Par.4 (Fixture Par.4-Par.0 (Fixture “ENTER” Button Save and Run 2/ 7 sequence Setting) sequence Setting) Auto Mode Manual AP01-AP04 (Mode Selection) S.000-S.008 (Strobe Speed) r.000-r.008 (Red) g.000-g.008 (Green) b.000-b.008 (Blue) u.000-u.008 (White) F.000-F.008 (Strobe Speed) SP.01-SP.02 (Sound Mode) AP** coLo Mode Sound Mode Soun 4 Channel Control Mode 4-CH AP04-AP01 (Mode Selection) S.008-S.000 (Strobe Speed) r.008-r.000 (Red) g.008-g.000 (Green) b.008-b.000 (Blue) u.008-u.000 (White) F.008-F.000 (Strobe Speed) SP.02-SP.01 (Sound Mode) Key Press doesn’t work in this mode 3.Function Instruction: 3-1、DMX Mode:when the fixture works as a single unit, please set Par.0 in the DMX working mode. When CH1=255、 CH5=1、CH6=2、CH7=3,CH8=4,it will switch to Obey4 control mode directly. When the fixtures works as a set, please set Par. 1~4 and DMX address A001. If the fixture is set to Par.0 or other DMX address, the slave units will work out of the way. 3-2、Auto Mode: There are 4 modes, which is AP01-AP04. Strobe speed can be set in each mode. 3-3、Manual Mode: Under this mode, RGB brightness and strobe speed can be set manually. r.000-r.008 refers to the brightness of red color、g.000-g.008 refers to the brightness of green color、b.000-b.008 refers to the brightness of blue color、u.000-u.008 refers to the brightness of white color. Strobe speed setting is the same as 3-2. 3-4、Sound Mode: Adjust the sound sensitive to the most suitable place and inset two kinds of sound modes 3-5、Temperature Protection Mode: Press Menu Button and then Enter Button, it will show the temperature of the light panel. 4.Single Par Light Usage and DMX Channel Instruction: 4-1、DMX Controller Connection: DMX512 Controller / Dmx line 4- Channel Controller Fixture Fixture Signal Par Par.0 第1个 Signal 第 Par n 个Par.0 Power line AC Power 100~240VAC 50/60Hz 4-2、DMX Channel Instruction: DMX Channel CH1 Function Mode DMX512 Value Description 000~030 DMX Mode(CH2、CH3、CH4、CH5、CH6,CH7) 031~080 081~140 141~170 171~200 201~240 Color Shade ,( CH2,CH3、CH4、CH5、CH6,CH7) Color Auto Mix(CH3) RGBW Auto Switch(CH3) 15 colors Auto Switch(CH3) Color Shade Automatically(CH3) 241~245:Sound Mode 1 241 255 2/ 7 CH2 CH3 CH4 CH5 CH6 CH7 All Dimmer for RGB Strobe/Fade Adjustment Red Brightness Adjustment Green Brightness Adjustment Blue Brightness Adjustment White Brightness Adjustment 000~015 016~255 246~255:Sound Mode 2 Light Out General Brightness:1%~100% 000~015 016~255 000~255 No Effect Strobe / fade Speed Red Brightness Adjustment 0%~100%. 000~255 Green Brightness Adjustment 0%~100%. 000~255 Blue Brightness Adjustment 0%~100%. 000~255 White Brightness Adjustment 0%~100%. 四 Instruction on Par Light Set 5-1、Controlled By DMX Controller 5-1-1、Connection DMX512 Controller / 4 Dmx line Power line Channel Controller Light Power line Light Power line 2nd Par Par.2 1st Par Par.1 Dmx line Light AC Power 100~240VAC 50/60Hz Power line 3rd Par Par.3 Dmx line Light 4th Par Par.4 Dmx line 5-1-2、Channel Listing 3/ 7 DMX Function Channel DMX512 Description Value Mode Selection 01 000~009 RGB Regulation,Channel : CH2~CH19 Mode Selection 02 010~029 Run Internal Program 01,Channel:CH3>15 Mode Selection 03 030~049 Run Internal Program 02, Channel :CH3>15 Mode Selection 04 050~069 Run Internal Program 03, Channel :CH3>15 Mode Selection 05 070~089 Run Internal Program 04, Channel :CH3>15 Mode Selection 06 090~109 Run Internal Program 05, Channel :CH3>15 Mode Selection 07 110~129 Run Internal Program 06, Channel :CH3>15 Mode Selection 08 130~149 Run Internal Program 07, Channel :CH3>15 Mode Selection 09 150~169 Run Internal Program 08, Channel :CH3>15 Mode Selection 10 170~189 Run Internal Program 09, Channel :CH3>15 Mode Selection 11 190~209 Run Internal Program 10, Channel :CH3>15 Mode Selection 12 210~229 Run Internal Program 11, Channel :CH3>15 Mode Selection 13 230~239 Run Internal Program 12, Channel :CH3>15 Mode Selection 14 240~255 CH2 RGB All Dim 000~255 Brightness :0%~100%,CH1<10 Valid CH3 Speed Selection 000~015 No Strobe,No Speed 016~255 Strobe Speed Selection 000~255 Par 1 Red LED Brightness 0%~100%. 000~255 Par 1 Green LED Brightness 0%~100%. 000~255 Par 1 Blue LED Brightness 0%~100%. 000~255 Par 1WhiteLED Brightness 0%~100%. 000~255 Par 2 Red LED Brightness 0%~100%. 000~255 Par 2 Green LED Brightness 0%~100%. 000~255 Par 2 Blue LED Brightness 0%~100%. 000~255 Par 2 White LED Brightness 0%~100%. 000~255 Par 3 Red LED Brightness 0%~100%. 000~255 Par 3 Green LED Brightness 0%~100%. 000~255 Par 3 Blue LED Brightness 0%~100%. 000~255 Par 3 White LED Brightness 0%~100%. 000~255 Par 4 Red LED Brightness 0%~100%. 000~255 Par 4 Green LED Brightness 0%~100%. 000~255 Par 4 Blue LED Brightness 0%~100%. 000~255 Par 4 White LED Brightness 0%~100%. CH1 CH4 Red LED Brightness 240~245:Sound Mode 1 246~255: Sound Mode 2 Adjustment CH5 Green LED Brightness Adjustment CH6 Blue LED Brightness Adjustment CH7 White LED Brightness Adjustment CH8 Red LED Brightness Adjustment CH9 Green LED Brightness Adjustment CH10 Blue LED Brightness Adjustment CH11 White LED Brightness Adjustment CH12 Red LED Brightness Adjustment CH13 Green LED Brightness Adjustment CH14 Blue LED Brightness Adjustment CH15 White LED Brightness Adjustment CH16 Red LED Brightness Adjustment CH17 Green LED Brightness Adjustment CH18 Blue LED Brightness Adjustment CH19 White LED Brightness Adjustment 4/ 7 Operation Instruction 1、Stand Alone Mode 1.Stand Alone Mode: Auto, manual and sound 2.Working Mode Setting:Press different button to enter different working mode 2、Master/ Slave Mode 1.Master/ Slave Mode: Auto, manual and sound mode and no need to use controller。 2.Working Mode Setting:Select one unit as the master(auto sound or manual),set up DMX address A001 in other units,and all lights light Sequence Par.0 at the same time. Master/ Slave Mode Light Signal Par Par.0 Host Power line Light Dmx line Signal Par Par.0 A001 Power line Light Dmx line Signal Par Par.0 A001 Power line AC Power 100~240VAC 50/60Hz 3.Cable Connection in Master/Slave mode:Connect the DMX output of the master and the input of the first slave unit with XLR-XLR cables, then connect the output of the first slave unit with the input of the second unit, the rest may be deduced by analogy until all the slave units are connected. 4. Four Channel Control Mode:Set up 4-channel mode for all the Par Lights in the loop. Press Menu Button until 4-CH is showed. Note: If more than one piece master unit or DMX controller, 4-channel controller is connected, the slave units may work out of the way 3、Master and Slave Working Mode for Par Light Set 1.Working Mode Setting:Set up the DMX address: A001 on all the Slave units and Par Light Sequence Par.1~4 Four pieces Par lights can form one set. Or the fixture can link with other products Neo-Neon produces so as to get more abundant stage effect. Fixture 1:IRDIP-9007426-00D-13(Single Unit 7x10W(4IN1)) 、IRDIP-9028426-00D-13(Light Set 7x10W(4IN1)) Fixture 2:IRDIP-4016126-00D-13(Single Unit 16x3W(RGBW)) 、IRDIP-4064126-00D-13(Light Set 16x3W(RGBW)) Fixture 3:IRDIP-2016126-00D-13(Single Unit 16x1W(RGBW)) 、IRDIP-2064126-00D-13(Light Set 16x1W(RGBW)) Fixture 4:IRDIP-9028444-00D-11(Double Light 7x10W(4IN1))(For development ) Fixture 5:IRDIP-4064164-00D-11(双灯 16x3W(RGBW))(For development) Fixture 6:IRDIP-2016124-00D-11(双灯 16x1W(RGBW))(For development) Fixture 7:IRDIP-9012426-00D-13(Epar-12x10W(4IN1)Par Light) Installation Hanging Or Level Installation Please find the hole in the middle of the bracket and fix the light with the clamp through these holes before hanging. You can use hanging cable as assistance. Make sure that the hanging cable can bear the weight which is 10 times of the hanging subjects. 5/ 7 Trouble Shooting Troubles Checking Item Trouble Shooting The unit doesn’t work 1.Check and see whether the input voltage is the same as the rating voltage。 2.Make sure that the working environment is suitable for the unit。 1.Make sure that the input voltage is the same as the rating voltage。 2.Ensure the working environment。 LED isn’t bright enough The unit is not controlled by the DMX Light set don’t work rightly The temperature doesn’t show 1.Check the polarity of the DMX control signal 2.See whether the unit is working under DMX mode 3.Check whether there are two masters 1. Make sure that the input voltage is the same as the rating voltage。 1.Correct the polarity of the DMX signal。 2.Set up DMX working mode。 3.Select only one master in the loop。 1.Check the light sequence of every par light 1.Correct the light sequence。 1.Check the thermal IC on the LED panel 1.Change the thermal IC 1.Check the input voltage 6/ 7
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project