Model MN170

Add to my manuals
4 Pages

advertisement

Model MN170 | Manualzz
OPERATION
Making Measurements with the AC Current Probe Model MN170
• Connect the current probe MN170 to the AC current range on your DMM or other current measuring
instrument. The AC Current Probe MN170 has a ratio of 100:1. This means that for 75A AC in a
conductor around which the probe is clamped, 750mA AC will come out of the probe leads to your DMM
or instrument. The output is 10mA AC/A AC. Select the range on your DMM or instrument which
corresponds best to the measured current. If the current magnitude is unknown, start with the highest
range first and work down until the appropriate range and resolution is reached. Clamp the probe around
the conductor. Take the reading on the meter and multiply it by 100 to obtain the measured current (e.g.,
60mA reading = 60 x 100 = 6,000mA or 6A).
• For best accuracy, avoid if possible, the proximity of other conductors which may create noise.
AC Current Probe
Models MN170
User Manual
DESCRIPTION
The MN170 (Catalog #100.270) is a mini current probe with 100:1 ratio for measurements to 75A AC.
Load impedance is limited to 0.14Ω.
Tips for Making Precise Measurements
• When using a current probe with a meter, it is important to select the range that provides the best
resolution. Failure to do this may result in measurement errors.
• Make sure that probe jaw mating surfaces are free of dust and contamination. Contaminants cause air
gaps between the jaws, increasing the phase shift between primary and secondary. It is very critical for
power measurement.
WARNING
These safety warnings are provided to ensure the safety of personnel and proper operation of the
instrument.
• Read the instruction manual completely and follow all the safety information before attempting
to use or service this instrument.
• Use caution on any circuit: Potentially high voltages and currents may be present and may
pose a shock hazard.
MAINTENANCE:
Warning
• For maintenance use only original factory replacement parts.
• To avoid electrical shock, do not attempt to perform any servicing unless you are qualified to do so.
• To avoid electrical shock and/or damage to the instrument, do not get water or other foreign agents
into the probe
Cleaning
To ensure optimum performance, it is important to keep the probe jaw mating surfaces clean at all times.
Failure to do so may result in error in readings. To clean the probe jaws, use a very fine sand paper (fine
600) to avoid scratching the jaw, then gently clean with a soft oiled cloth.
REPAIR AND CALIBRATION
You must contact our Service Center for a Customer Service Authorization number (CSA#). This will
ensure that when your instrument arrives, it will be tracked and processed promptly. Please write the CSA#
on the outside of the shipping container. If the instrument is returned for calibration, we need to know if you
want a standard calibration, or a calibration traceable to N.I.S.T. (includes calibration certificate plus
recorded calibration data).
Chauvin Arnoux®, Inc. d.b.a. AEMC® Instruments
15 Faraday Drive • Dover, NH 03820 USA
Tel:
(800) 945-2362 (Ext. 360), (603) 749-6434 (Ext. 360)
Fax:
(603) 742-2346 or (603) 749-6309
[email protected]
(Or contact your authorized distributor)
Costs for repair, standard calibration, and calibration traceable to N.I.S.T. are available.
NOTE: All customers must obtain a CSA# before returning any instrument.
TECHNICAL AND SALES ASSISTANCE
If you are experiencing any technical problems, or require any assistance with the proper use or
application of this instrument, please call our technical hotline:
(800) 343-1391 • (508) 698-2115 • Fax (508) 698-2118
Chauvin Arnoux®, Inc. d.b.a. AEMC® Instruments
[email protected]
99-MAN 100025.v3 07/04
• Read the Safety Specifications section prior to using the current probe. Never exceed the
maximum voltage ratings given.
• Safety is the responsibility of the operator.
• ALWAYS connect the current probe to the display device before clamping the probe onto the
sample being tested.
• ALWAYS inspect the instrument, probe, probe cable, and output terminals prior to use.
Replace any defective parts immediately.
• NEVER use the current probe on electrical conductors rated above 600V in overvoltage
category III (CAT III). Use extreme caution when clamping around bare conductors or bus bars.
INTERNATIONAL ELECTRICAL SYMBOLS
This symbol signifies that the current probe is protected by double or reinforced insulation.
Use only specified replacement parts when servicing the instrument.
This symbol signifies CAUTION! and requests that the user refer to the user manual
before using the instrument.
RECEIVING YOUR SHIPMENT
Upon receiving your shipment, make sure that the contents are consistent with the packing list. Notify
your distributor of any missing items. If the equipment appears to be damaged, file a claim immediately
with the carrier and notify your distributor at once, giving a detailed description of any damage.
PACKAGING
The AC Current Probe MN170 is shipped with this instruction manual and a product warranty and
registration card. You can register online at www.aemc.com.
INSTRUMENT COMPATIBILITY
The Model MN170 is compatible with any ammeter, multimeter, or other current measuring instruments
with an input impedance of 0.14Ω or less. To achieve the stated accuracy, use the MN170 with a
ammeter having an accuracy of 1% or better.
Ø=0.47" max.
(12 mm)
ELECTRICAL SPECIFICATIONS
Dimensions:
1.26 x 4.53 x 0.87"
Current Range:
2 to 75A AC
(32 x 115 x 22 mm)
Transformation Ratio:
100:1
Output Signal:
10mA AC/A AC (750mA @ 75 A)
4.53" (115 mm)
Accuracy and Phase Shift*:
±3% (with noninductive load ≤ 0.14Ω)
Black
Weight:
100 g (4 oz)
Colors:
Dark gray handles with red cover
Polycarbonate Material:
Handle: 10% Figerglass charged
polycarbonate UL 94 V0
Frequency Range:
45 to 1000 Hz
Output:
Standard 4mm banana jacks
Load Impedance:
0.14Ω max noninductive
Dielectric Test:
3000V RMS
Red
Working Voltage:
250V max
ORDERING INFORMATION
MECHANICAL SPECIFICATIONS
Operating Temperature:
14° to 122°F (-10° to 50°C)
Storage Temperature:
-40° to 167°F (-40° to 75°C)
1.26"
(32 mm)
0.87"
(22 mm)
Maximum Cable Diameter:
0.47” Ø max. (12 mm)
AC Current Probe
MN170........................... Cat #100.270
Accessories:
Pair, current leads
(39” color-coded) .............Cat #100.361
Pair, safety current leads
(5 ft retractable, 250V).....Cat #100.319
Ø=0.47" max.
(12 mm)
ELECTRICAL SPECIFICATIONS
Dimensions:
1.26 x 4.53 x 0.87"
Current Range:
2 to 75A AC
(32 x 115 x 22 mm)
Transformation Ratio:
100:1
Output Signal:
10mA AC/A AC (750mA @ 75 A)
4.53" (115 mm)
Accuracy and Phase Shift*:
±3% (with noninductive load ≤ 0.14Ω)
Black
Weight:
100 g (4 oz)
Colors:
Dark gray handles with red cover
Polycarbonate Material:
Handle: 10% Figerglass charged
polycarbonate UL 94 V0
Frequency Range:
45 to 1000 Hz
Output:
Standard 4mm banana jacks
Load Impedance:
0.14Ω max noninductive
Dielectric Test:
3000V RMS
Red
Working Voltage:
250V max
ORDERING INFORMATION
MECHANICAL SPECIFICATIONS
Operating Temperature:
14° to 122°F (-10° to 50°C)
Storage Temperature:
-40° to 167°F (-40° to 75°C)
1.26"
(32 mm)
0.87"
(22 mm)
Maximum Cable Diameter:
0.47” Ø max. (12 mm)
AC Current Probe
MN170........................... Cat #100.270
Accessories:
Pair, current leads
(39” color-coded) .............Cat #100.361
Pair, safety current leads
(5 ft retractable, 250V).....Cat #100.319
OPERATION
Making Measurements with the AC Current Probe Model MN170
• Connect the current probe MN170 to the AC current range on your DMM or other current measuring
instrument. The AC Current Probe MN170 has a ratio of 100:1. This means that for 75A AC in a
conductor around which the probe is clamped, 750mA AC will come out of the probe leads to your DMM
or instrument. The output is 10mA AC/A AC. Select the range on your DMM or instrument which
corresponds best to the measured current. If the current magnitude is unknown, start with the highest
range first and work down until the appropriate range and resolution is reached. Clamp the probe around
the conductor. Take the reading on the meter and multiply it by 100 to obtain the measured current (e.g.,
60mA reading = 60 x 100 = 6,000mA or 6A).
• For best accuracy, avoid if possible, the proximity of other conductors which may create noise.
AC Current Probe
Models MN170
User Manual
DESCRIPTION
The MN170 (Catalog #100.270) is a mini current probe with 100:1 ratio for measurements to 75A AC.
Load impedance is limited to 0.14Ω.
Tips for Making Precise Measurements
• When using a current probe with a meter, it is important to select the range that provides the best
resolution. Failure to do this may result in measurement errors.
• Make sure that probe jaw mating surfaces are free of dust and contamination. Contaminants cause air
gaps between the jaws, increasing the phase shift between primary and secondary. It is very critical for
power measurement.
WARNING
These safety warnings are provided to ensure the safety of personnel and proper operation of the
instrument.
• Read the instruction manual completely and follow all the safety information before attempting
to use or service this instrument.
• Use caution on any circuit: Potentially high voltages and currents may be present and may
pose a shock hazard.
MAINTENANCE:
Warning
• For maintenance use only original factory replacement parts.
• To avoid electrical shock, do not attempt to perform any servicing unless you are qualified to do so.
• To avoid electrical shock and/or damage to the instrument, do not get water or other foreign agents
into the probe
Cleaning
To ensure optimum performance, it is important to keep the probe jaw mating surfaces clean at all times.
Failure to do so may result in error in readings. To clean the probe jaws, use a very fine sand paper (fine
600) to avoid scratching the jaw, then gently clean with a soft oiled cloth.
REPAIR AND CALIBRATION
You must contact our Service Center for a Customer Service Authorization number (CSA#). This will
ensure that when your instrument arrives, it will be tracked and processed promptly. Please write the CSA#
on the outside of the shipping container. If the instrument is returned for calibration, we need to know if you
want a standard calibration, or a calibration traceable to N.I.S.T. (includes calibration certificate plus
recorded calibration data).
Chauvin Arnoux®, Inc. d.b.a. AEMC® Instruments
15 Faraday Drive • Dover, NH 03820 USA
Tel:
(800) 945-2362 (Ext. 360), (603) 749-6434 (Ext. 360)
Fax:
(603) 742-2346 or (603) 749-6309
[email protected]
(Or contact your authorized distributor)
Costs for repair, standard calibration, and calibration traceable to N.I.S.T. are available.
NOTE: All customers must obtain a CSA# before returning any instrument.
TECHNICAL AND SALES ASSISTANCE
If you are experiencing any technical problems, or require any assistance with the proper use or
application of this instrument, please call our technical hotline:
(800) 343-1391 • (508) 698-2115 • Fax (508) 698-2118
Chauvin Arnoux®, Inc. d.b.a. AEMC® Instruments
[email protected]
99-MAN 100025.v3 07/04
• Read the Safety Specifications section prior to using the current probe. Never exceed the
maximum voltage ratings given.
• Safety is the responsibility of the operator.
• ALWAYS connect the current probe to the display device before clamping the probe onto the
sample being tested.
• ALWAYS inspect the instrument, probe, probe cable, and output terminals prior to use.
Replace any defective parts immediately.
• NEVER use the current probe on electrical conductors rated above 600V in overvoltage
category III (CAT III). Use extreme caution when clamping around bare conductors or bus bars.
INTERNATIONAL ELECTRICAL SYMBOLS
This symbol signifies that the current probe is protected by double or reinforced insulation.
Use only specified replacement parts when servicing the instrument.
This symbol signifies CAUTION! and requests that the user refer to the user manual
before using the instrument.
RECEIVING YOUR SHIPMENT
Upon receiving your shipment, make sure that the contents are consistent with the packing list. Notify
your distributor of any missing items. If the equipment appears to be damaged, file a claim immediately
with the carrier and notify your distributor at once, giving a detailed description of any damage.
PACKAGING
The AC Current Probe MN170 is shipped with this instruction manual and a product warranty and
registration card. You can register online at www.aemc.com.
INSTRUMENT COMPATIBILITY
The Model MN170 is compatible with any ammeter, multimeter, or other current measuring instruments
with an input impedance of 0.14Ω or less. To achieve the stated accuracy, use the MN170 with a
ammeter having an accuracy of 1% or better.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement