Aspire T120E/AcerPower M2
Service Guide
Service guide files and updates are available
on the AIPG/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on Aspire T120E service guide.
Date
4
Chapter
Updates
Copyright
Copyright © 2004 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium 4 and Celeron are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
5
Conventions
The following conventions are used in this manual:
6
Screen messages
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
7
Chapter 1 System Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Mainboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hardware Specifications and Configurations . . . . . . . . . . . . 13
Power Management Function (ACPI support function) . . . . 18
Chapter 2 System Utilities . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . .19
Entering Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard CMOS Features . . . . . . . . . . . . . . . . . . . . . . . . . .
Advanced BIOS Features . . . . . . . . . . . . . . . . . . . . . . . . . . .
Integrated Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PnP/PCI Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Health Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Frequency Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Load Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Supervisor/User Password . . . . . . . . . . . . . . . . . . . . . . .
Save & Exit Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exit Without Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
22
23
25
27
30
31
32
33
34
35
36
Chapter 3 Machine Disassembly and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 37
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Disassembly Flow Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Standard Disassembly Procedure . . . . . . . . . . . . . . . . . . . . 40
Chapter 4 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Boot up Troubleshooting Flow Chart . . . . . . . . . . . . . . . . . . .
Power-On Self-Test (POST) . . . . . . . . . . . . . . . . . . . . . . . . .
POST Check Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
POST Error Messages List . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Symptoms List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . .
50
52
53
59
61
66
Chapter 5 Jumper and Connector Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
I/O Back Panel Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 67
CONN & Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Front Panel Switch/LED Connector . . . . . . . . . . . . . . . . . . . 75
Chapter 6 FRU(Field Replaceable Unit) List76
Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Appendix A Model Definition and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Appendix B Test Compatible Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Appendix C Online Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
1
Chapter 1
System Specifications
Features
CPU
T
Support AMD AthlonTM /AthlonTM XP/ DuronTM CPU.
T
Support 333/400MHz CPU FSB.
T
Support 1.4GHz and faster.
Chipset
T
North Bridge :SiS 741
T
South Bridge : SiS 964L
Memory
T
Socket Type: 184-pin socket.
T
Socket Quantity: 2
T
Memory Type:DDR-SDRAM 400/333/266 DIMM
T
Support 128MB, 256MB and 512MB DDR memory technologies
T
Max Cpapcity:Up to 2.0 GB
T
Support STR(Suspend to RAM)
T
Support for unbuffered ECC, non-ECC RAM
Graphics
T
SiS on-die graphic solution
T
UDMA technology support
T
Dual view function support
T
1 VGA port on rear
AGP/PCI Slots
T
AGP Slot Type : AGP 8X 1.5V Slot(Backwards compatible with AGP 4X)
T
Support Maximum AGP interface bandwidth 2.1GB/s
T
AGP Slot Quantity : 1
T
PCI Slot Type : PCI 2.2 5V Slots
T
PCI Slot Quantity : 3
T
One FDD slot supports 1.44MB/ 3 mode 3.5” devices
T
Slot Type: 40 pin IDE slot
FDD
IDE
Chapter 1
T
Slot Quantity: 2
T
support ATA 66/100/133
1
T
T
support PIO 0/1/2/3/4
Storage Type support
T
HDD/CD-ROM/CD-RW/DVD
T
Zip250
Audio
T
Chip : AC’ 97 CODEC, 20 bit with amplifier
T
Type : RealTeck ALC655
T
Channel : 2
T
Support stereo speakers with built-in subwoofer
T
Supports 10/100MB ethernet environment
T
Type : Build in RealTek RTL 8201CL chipset
T
Connectors Quantity:8
LAN
USB
T
T
Rear Connectors: 4
T
On-board header: 4
T
2 for front daughter board
T
1 for 6 in 1 card reader
Transfer Rate:
T
USB 2.0/1.1
BIOS
T
4MB flash BIOS
T
Award BIOS compatible with SMBIOS 2.3, ACPI 2.0, and APM 1.2
T
PCI 2.3 compilance
T
Support DMI, WFM 2.0, WOL
I/O Connector
Front Panel
T
2 USB ports
T
1 headphone out
T
1 microphone in
Rear Panel
2
T
1 PS/2 keyboard port, 1 PS/2 mouse port
T
1 RJ45 LAN port
T
1 Parallel port, 1 TV out connector
T
4 USB ports
T
1 VGA(CRT)Connector
T
1 Line In, 1 Line Out, and 1 Microphone In port
Chapter 1
Controls and Indicators
Chapter 1
T
1 Power Switch
T
1 single color Power state LED (Green)
T
1 single color LED for HDD state(Green)
T
1 single color LED for LAN state(Green)
3
Mainboard Layout
CPU_FAN
ATX_12V
KB_MS
R_USB
GA-7S741M
LPT
COMA
ATX
VGA
SOCKETA
AUX_IN
IDE1
FDD
SYS _FAN
SiS 741
CD_IN
AGP
RTL8201C L
DDR1
F_AUDIO
I T8705F
CLK _SW
DDR2
MIC_IN
LINE_OUT
LINE_IN
USB_LAN
IDE2
BAT
PCI1
BIOS
SiS 964L
CLR_CMOS
PCI2
BZ
PCI3
CODEC
F_U SB2
COMB
Label
AGP
4
F_US B_WK F_PANEL
F_U SB1
Component
AGP Slot
BAT
Battery
CD_IN
CD IN Connector
BIOS
BIOS
COMA/COMB
Serial Port
SOCKETA
Socket for CPU
CPU_FAN
Processor fan connector
SYS_FAN
System fan connector
DDR1,DDR2
DIMM Port
F_AUDIO
Front Audio Connector
F_USB1,F_USB2
Front USB Connector
R_USB
Rear USB
FDD
Floppy Connector
F_PANEL
Front Panel Header
KB/MS
PS2-KBMS
USB_LAN
Network/USB Connector
Chapter 1
Label
Component
PCI 1,2,3
PCI Slot
IDE1,IDE2
Primary and Secondary IDE Connector
ATX_12V
ATX 12V power connector
SiS 741
North Bridge Chipset
SiS 946
South Bridge Chipset
IT8705F
I/O connector
RTL8201CL
LAN chip
VGA
VGA port
LPT
Print port
AUX_IN
AUX in Connector
ATX
ATX Main power connector
CODEC
Audio chip
MIC_IN/LINE_OUT/LINE_IN
MIC_IN/LINE_OUT/LINE_IN connector
F_USB_WK
Front USB Wake Up Function Jumper
CLK_SW
Set System Switch. The CPU FSB can be switched by CLK_SW
BZ
Buzzer
Chapter 1
5
Block Diagram
K7
Socket A
CPU
AGP 4X/8X
CPUCLK+/- (100/133/166/200MHz)
System Bus
200/266/333/400MHz FSB
AGPCLK
(66MHz)
DDR
SiS 741
266/333/400 MHz
ZCLK (66/133MHz)
HCLK+/- (100/133/166/200MHz)
RJ45
66/133 MHz
33 MHz
14.318 MHz
48 MHz
3 PCI
RTL8201CL
BIOS
SiS 964L
AC97 Link
LPC BUS
IT8705F
LPT Port
6
MIC
LINE-IN
LINE-OUT
AC97
CODEC
PCICLK
(33MHz)
Floppy
24 MHz
8 USB
Ports
ATA33/66/100
IDE Channels
PS/2
KB/Mouse
33 MHz
COM
Ports
Chapter 1
Front Panel
The computer’s front panel consists of the following:
Aspire T120E
No.
Description
Label
No.
Description
Description
1
Optical Drive
2
Floppy Drive
3
7-in-1 Card Reader(Manufacturing Option)
4
Power button
5
Speaker or Headphone Jack
6
Microphone Jack
7
USB Ports
Chapter 1
7
AcerPower M2
No.
8
Description
No.
Description
Label
Description
1
Optical Drive
2
Floppy Drive
3
7-in-1 Card Reader(Manufacturing Option)
4
Power button
5
Speaker or Headphone Jack
6
Microphone Jack
7
USB Ports
8
Indicators
Chapter 1
Rear Panel
Aspire T120E
1
2
3
4
5
6
7
8
9
10
13
11
12
14
No.
Description
Description
Label
Icon
1
N/A
N/A
Power code socket
2
N/A
N/A
Voltage selector switch
3
N/A
N/A
Fan Aperture
4
Purple
PS/2 keyboard port
5
Green
PS/2 mouse port
N/A
Serial out port
7
Burgundy
Parallet/Printer Connector
8
Blue
CRT/LCD Monitor Connector
6
Chapter 1
N/A
Color
No.
Description
9
Label
Color
Description
Black
USB Connectors
10
Black
RJ-45 Ethernet Connector
11
Pink
Microphone-In Port (Rear)
12
Lime
Audio-out/Line-out jack
13
Light Blue
Audio-in/Line-in jack
N/A
IEEE 1394 Port
14
10
Icon
9
N/A
Chapter 1
AcerPower M2
No.
Description
No.
Description
Label
Icon
Color
Description
1
N/A
N/A
Power code socket
2
N/A
N/A
Voltage selector switch
3
N/A
N/A
Fan Aperture
4
Green
PS/2 mouse port
5
Purple
PS/2 keyboard port
6
Black
USB Connectors
7
Burgundy
Parallel/Printer Connector
8
N/A
N/A
Serial Port
9
N/A
N/A
VGA Port
Black
USB Connectors
10
Chapter 1
11
Label
Color
Description
Black
RJ-45 Ethernet Connector
12
Pink
Microphone Jack
13
Lime
Line-out Jack
14
Light Blue
Line-in Jack
N/A
VGA Port
15
12
Icon
11
N/A
16
N/A
N/A
S-video out port
17
N/A
N/A
Digital Visual Interface
18
N/A
N/A
TV Tuner Card
Chapter 1
Hardware Specifications and Configurations
Processor
Item
Specification
Type
AMD AthlonTM XP / AthlonTM/DuronTM
Socket
Socket A
Speed
1.4 GHz and faster
Minimum operating speed
0 MHz (If Stop CPU Clock in Sleep State in BIOS Setup is
set to Enabled.)
BIOS
Item
Specification
BIOS code programmer
Award
System BIOS version
R01-A0
SMBIOS version
2.3
BIOS ROM type
Flash ROM
BIOS ROM size
2MB
Support protocol
PCI 2.0, APM1.2, WFM2.0, , ACPI 2.0, ESCD 1.03,
SMBIOS2.3, USB1.1,USB2.0
Boot from CD-ROM feature
Yes
Support to LS-120 drive
Yes
Support to BIOS boot block feature
Yes
NOTE: The BIOS can be overwritten/upgraded by using the flash utility.
BIOS Hotkey List
Hotkey
c
Chapter 1
Function
Enter BIOS Setup Utility
Description
Press while the system is booting to
enter BIOS Setup Utility.
13
This section has two table lists, system memory specification and the possible combinations of memory
module.
System Memory
Item
Specification
Memory slot number
2 slot
Support memory size per socket
128MB / 256MB/ 512MB
Support maximum memory size
1.0G
Support memory type
DDR SDRAM
Support memory speed
DDR 333/400
Support memory voltage
2.5 V
Support memory module package
184-pin DIMM
Support to parity check feature
Yes
Support Non-ECC type module
Yes
Memory module combinations
You can install memory modules in any combination as
long as they match the above specifications.
Memory Combinations
Slot
Memory Module
Total Memory
Slot 1
128, 256, 512MB
128MB~1G
Slot 2
128, 256, 512MB
128MB~1G
Maximum System Memory Supported
128MB~1.0G
Cache Memory
Item
Specification
First-Level Cache Configurations
Cache function control
Enable/Disable by BIOS Setup
Second-Level Cache Configurations
L2 Cache RAM type
By CPU
L2 Cache RAM size
By CPU
L2 Cache RAM speed
By CPU
L2 Cache RAM voltage
By CPU
L2 Cache function control
Enable/Disable by BIOS Setup
L2 Cache scheme
Fixed in write-back
This section has two table lists, the video interface specification and its supported display modes.
Video Interface
Item
14
Specification
Video controller
SiS 741
Video controller resident bus
AGP Bus
Video interface support
AGP 8X/4X 1.5V mode
On Board VGA
Build in SiS741 chipset
Chapter 1
Audio Interface
Item
Specification
Audio controller
SiS 946L
Audio controller resident bus
AC’97 Link
Audio function control
Enable/disable by BIOS Setup
Mono or stereo
Stereo
Resolution
20 bits
Compatibility
Sound Blaster Pro/16 compatible
Mixed digital and analog high performance chip
Enhanced stereo full duplex operation
High performance audio accelerator and AC’97 support
Full native DOS games compatibility
Virtual FM enhances audio experience through real-time FM-toWavetable conversion
MPU-401(UART mode) interface for wavetable synthesizers and
MIDI devices
Integrated dual game port
Meets AC’97and WHQL specifications
Music synthesizer
48 KHz
Sampling rate
48 KHz (max.)
MPU-401 UART support
Yes
Microphone jack
Yes
Headphone jack
Yes
IDE Interface
Item
Specification
IDE controller
SiS 946L
IDE controller resident bus
PCI bus
Number of IDE channel
2
Support IDE interface
2 IDE bus master(UDMA33/ATA66/ATA100)IDE ports for up to 4
ATAPI devices
Floppy disk drive Interface
Item
Specification
Floppy disk drive controller
ITE8705F
Floppy disk drive controller resident
bus
LPC bus
Support FDD format
360KB, 720KB, 1.2MB, 1.44MB, 2.88MB
Chapter 1
15
Parallel Port
Item
Specification
Parallel port controller
ITE8705F
Parallel port controller resident bus
LPC bus
Number of parallel ports
1
Support ECP/EPP
SPP / Bi-directional / ECP / EPP
Connector type
25-pin D-type female connector
Parallel port function control
Enable/disable by BIOS Setup
Optional ECP DMA channel
(in BIOS Setup)
Support
Optional parallel port I/O address
(via BIOS Setup)
Support
Optional parallel port IRQ
(via BIOS Setup)
Support
Serial Port
Item
Specification
Serial port controller
ITE8705L
Serial port controller resident bus
LPC bus
Number of serial port
2
16550 UART support
Yes
Connector type
9-pin D-type female connector
Optional serial port I/O address
(via BIOS Setup)
COM1: Yes
COM2: No
Optional serial port IRQ
(via BIOS Setup)
COM1: Yes
COM2: No
USB Port
Item
Specification
Universal HCI
USB 2.0/1.1
USB Class
Support legacy keyboard for legacy mode
USB Number
8 ( 4 on front , 4 on rear )
Main Board Major Chips
Item
16
Controller
System core logic
SiS 741
Video controller
SiS 741
Super I/O controller
ITE8705F
Audio controller
AC97Link
Chapter 1
Main Board Major Chips
Item
Controller
LAN controller
RTL8201CL
HDD controller
ITE8705F
Keyboard controller
ITE8705F
Environmental Requirements
Item
Specifications
Temperature
Operating
+5 ~ +35°C
Non-operating
-20 ~ +60°C (Storage package)
Humidity
Operating
15% to 80% RH
Non-operating
10% to 90% RH
Vibration
Operating (unpacked)
5 ~ 500 Hz: 2.20g RMS random
Non-operating (packed)
5 ~ 500 Hz: 0.19g RMS random
Switching Power Supply 230W
Input Frequency
Frequency Variation Range
50Hz
50Hz to 60Hz
60Hz
50Hz to 60Hz
Input Voltage
Variation Range
100 - 120 VRMS
90 - 132 VRMS
200 - 240 VRMS
180 - 264 VRMS
Input Current
Measuring Range
4A
90 -132 VRMS
2A
180 - 264 VRMS
Output Requirements
Regulation
Current Rating
+5V
+-5%
15A
+12V
+-5%
3A
-12V
+-10%
0.3A
+3.3V
+-4%
12A
+5Vaux
+-5%
3A
Chapter 1
17
Power Management Function (ACPI support function)
Device Standby Mode
T
Independent power management timer for hard disk drive devices
(0-15 minutes, time step=1 minute).
T
Hard disk drive goes into Standby mode (for ATA standard interface).
T
Disable V-sync to control the VESA DPMS monitor.
T
Resume method: device activated (Keyboard for DOS, keyboard & mouse for Windows).
T
Resume recovery time: 3-5 sec.
Global Standby Mode
T
Global power management timer (2-120 minutes, time step=10 minute).
T
Hard disk drive goes into Standby mode (for ATA standard interface).
T
Disable H-sync and V-sync signals to control the VESA DPMS monitor.
T
Resume method: Return to original state by pushing external switch button, modem ring in,
keyboard and mouse for APM mode.
T
Resume recovery time: 7-10 sec.
Suspend Mode
T
Independent power management timer (2-120 minutes, time step=10 minutes) or pushing external
switch button.
T
CPU goes into SMM.
T
CPU asserts STPCLK# and goes into the Stop Grant State.
T
LED on the panel turns amber colour.
T
Hard disk drive goes into SLEEP mode (for ATA standard interface).
T
Disable H-sync and V-sync signals to control the VESA DPMS monitor.
T
Ultra I/O and VGA chip go into power saving mode.
T
Resume method: Return to original state by pushing external switch button, modem ring in,
keyboard and mouse for APM mode.
T
Return to original state by pushing external switch button, modem ring in and USB keyboard for
ACPI mode.
T
ACPI specification 1.0b.
T
S0, S1, S3 and S5 sleep state support.
T
On board device power management support.
T
On board device configuration support.
ACPI
18
Chapter 1
Chapter 2
System Utilities
Most systems are already configured by the manufacturer or the dealer. There is no need to run
Setup when starting the computer unless you get a Run Setup message.
The Setup program loads configuration values into the battery-backed nonvolatile memory called CMOS RAM.
This memory area is not part of the system RAM.
NOTE: If you repeatedly receive Run Setup messages, the battery may be bad/flat. In this case, the system
cannot retain configuration values in CMOS.
Before you run Setup, make sure that you have saved all open files. The system reboots immediately after you
exit Setup.
Chapter 2
19
Entering Setup
Power on the computer and the system will start POST (Power On Self Test)process. When the message of
“Press DEL to enter SETUP” appears on the screen, press the key of [Delete] to enter the setup menu.
NOTE: If the message disappears before you respond and you still wish to enter Setup, restart the system by
turning it OFF and On. You may also restart the system by simultaneously pressing [Ctrl+Alt+Delete].
The Setup Utility main menu then appears:
CMOS Setup Utility-Copyright © 1984-2004 Award Software
XProduct Information
XPC Health Status
XStandard CMOS Features
XFrequency Control
XAdvanced BIOS Features
Load Default Settings
XAdvanced Chipset Features
Set Supervisor Password
XIntegrated Peripherals
Set User Password
XPower Management Setup
Save & Exit Setup
XPnP/PCI Configurations
Exit Without Saving
ESC: Quit
F10: Save & Exit Setup
IJKL: Select Item
Product name, System S/W….
The command line at the bottom of the menu tells you how to move within a screen and from one screen to
Xanother.
X
T
To select an option, move the highlight bar by pressing
X
T
To change a parameter setting, press
X
T
Press
to return to the main menu. If you are already in the main menu, press
exit Setup.
or
or
then press
.
until the desired setting is found.
again to
XThe parameters on the screens show default values. These values may not be the same as those in your
Xsystem.
The grayed items on the screens have fixed settings and are not user-configured.
X
NOTE: Due to the application of a new version of BIOS Setup program, you may find the BIOS menu is largely
different from the former models. However, you will soon find out that this version is much more
IJKL
compact than the former ones.
20
Chapter 2
The items in the main menu are explained below:
T
Product Information
To introduce the Product Name,System P/N and MainBoard ID...etc.
T
Standard CMOS Features
The basic system configuration can be set up through this menu.
T
Advanced BIOS Features
The advanced system features can be set up through this menu.
T
Advanced Chipset Features
The advanced chipset features can be set up through this menu
T
Integrated Peripherals
All onboard peripherals can be set up through this menu.
T
Power Management Setup
All the items of Green function features can be set up throgh this menu.
T
PnP/PCI Configurations
The system’s PnP/PCI settings and parameters can be modified through this menu.
T
PC Health Staus
This will display the current status of your PC.
T
Frenquency Control
This setup pages is control CPU clock and frequency ratio.
T
Load Default Settings
These parameter settings can be loaded through this menu, however, the stable default values
may be affected.
T
Set Supervisor/User Password
The supervisor/user password can be set up through this menu.
T
Save & Exit Setup
Save CMOS value settings to CMOS and exit setup.
T
Exit Without Saving
Abandon all CMOS value changes and exit setup.
Chapter 2
21
Product Information
The screen below appears if you select Product Information from the main menu:
The Product Information menu contains general data about the system, such as the product name, serial
number, BIOS version, etc. These information is necessary for troubleshooting (maybe required when
asking for technical support).
CMOS Setup Utility-Copyright © 1984-2004 Award Software
Product Information
Product Name
System S/N
Main Board ID
Main Board S/N
System BIOS Version
SMBIOS Version
System BIOS ID
BIOS Build Date
KLIJ: Move Enter: Select
F5: Previous Values
Item Help
Menu Level X
Aspire T120E
G74M
R01-A3 S1
2.3
R01-A3 S1
2005/3/16
+/-/PU/PD: Value F10:Save
F7: Default Settings
ESC: Exit
F1: General Help
The following table describes the parameters found in this menu:
Parameter
22
Description
Product Name
Displays the model name of your system.
System S/N
Displays your system’s serial number.
Main Board ID
Displays the main board’s identification number.
Main Board S/N
Displays your main board’s serial number.
System BIOS Version
Specifies the version of your BIOS utility.
SMBIOS version
The System Management Interface (SM) BIOS allows you to check your system
hardware components without actually opening your system. Hardware
checking is done via software during start up. This parameter specifies the
version of the SMBIOS utility installed in your system.
System BIOS ID
Displays the BIOS identification number.
BIOS Release Date
Displays the date BIOS released.
Chapter 2
Standard CMOS Features
Select Standard CMOS Features from the main menu to configure some basic parameters in your system.
The following screen shows the Standard CMOS Features menu:
CMOS Setup Utility-Copyright © 1984-2004 Award Software
Standard CMOS Features
Date (mm:dd:yy)
Thu, Apr 29,2004
Item Help
Time (hh:mm:ss)
22:31:24
Menu Level >
X IDE Channel 0 Master
X IDE Channel 0 Slave
Change the day, month,
year
[None]
[None]
<Week>
Sun. to Sat.
Drive A
[1.44M, 3.5"]
Drive B
[None]
Floppy 3 Mode Support [Disabled]
Holt On
<Month>
Jan. to Dec.
[All, But Keyboard]
<Day>
Base Memory
Extended Memory
Total Memory
1 to 31 for maximum
allowed in the month
640K
127M
128M
KLIJ: Move Enter: Select
F5: Previous Values
<Year>
1999 to 2098
+/-/PU/PD: Value F10:Save
F6: Fail-Save Default
ESC: Exit
F1: General Help
F7: Optimized Defaults
The following table describes the parameters found in this menu. Settings in boldface are the default and
suggested settings.
Parameter
Date
Description
Lets you set the date following the weekdaymonth-day-year format
Options
Weekday: Sun, Mon...Sat
Month: Jan., Feb...Dec.
Day: 1 to 31
Year: 1999 to 2098
Time
Lets you set the time following the hour-minutesecond format
Hour: 0 to 23
Allows you to configure the hard disk drive
connected to the master port of IDE channel.
IDE Device Model Number:
None
Minute: 0 to 59
Second: 0 to 59
IDE Primary Master
To enter the IDE Primary Master setup, press
[Enter]. The IDE CD-ROM is always
automatically detected.
IDE Primary Slave
Allows you to configure the hard disk drive
connected to the slave port of IDE channel.
IDE Device Model Number:
None
To enter the IDE Primary Slave setup, press
[Enter]. The IDE CD-ROM is always
automatically detected.
Chapter 2
23
Parameter
IDE Secondary Master
Description
Allows you to configure the hard disk drive
connected to the master port of IDE channel 1.
Options
IDE Device Model Number:
None
To enter the IDE Channel 1 Master setup, press
[Enter].
The IDE CD-ROM is always automatically
detected.
IDE Secondary Slave
Allows you to configure the hard disk drive
connected to the slave port of IDE channel 2.
IDE Device Model Number:
None
To enter the IDE Channel Secondary Master
setup, press [Enter]. The IDE CD-ROM is always
automatically detected.
Drive A
Allows you to configure your floppy drive A.
None
360 KB, 5.25-inch
1.2 MB, 5.25-inch
720 KB, 3.5-inch
1.44M, 3.5 - inch
2.88 MB, 3.5-inch
Halt On
This parameter enables you to control the
system stops in case of Power On Self Test
errors (POST).
All Errors
No Errors
All, but Keyboard
All, but Diskette
All, by Disk/Key
24
Base Memory
Refers to the option of memory that is available
to standard DOS programs. DOS systems have
an address space od 1MB, but the top 384KB
(called high memory) is reserved for system use.
This leaves 640 KB of conventional memory.
Everything above 1MB is either extended or
extended memory.
The BIOS POST will determine
the amount of base (or
conventional) memory installed
in the sytem.
Extended Memory
Memory above and beyond the standard 1MB of
base memory that DOS supports. Extended
memory is only available in PCs with an Intel
80286 or later microprocessor. Extended
memory is not configured in any special manner
and is therefore unavailable to most DOS
programs. However, MS Windows and OS/2 can
use extended memory.
The BIOS determines how much
extended memory is present
during the POST.
Total Memory
Total based and extended memory, and I/O ROM
384KB available to the system.
total memory of the system.
Chapter 2
Advanced BIOS Features
The following screen shows the Advanced BIOS Features:
CMOS Setup Utility-Copyright © 1984-2004 Award Software
Advanced BIOS Features
Virus Warning
[Disabled]
Item Help
Silent Boot
[Enabled]
Configuration Table
[Disabled]
Menu Level X
Quick Power On Self Test [Enabled]
Hard Disk Boot Priority [Press Enter]
First Boot Device
[CDROM]
Second Boot Device
[Floppy]
Third Boot Device
[CD ROM]
Boot Other Device
[Enabled]
Boot Up NumLock Status [On]
Gate A20 Option
[Fast]
APIC Mode
[Enabled]
KLIJ: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value F10:Save
F6: Fail-Save Default
ESC: Exit
F1: General Help
F7: Optimized Defaults
The following table describes the parameters found in this menu. Settings in boldface are the default and
suggested settings.
Parameter
Virus Warning
Silent Boot
Description
Options
Allows you to choose the VIRUS warning
feature for IDE Hard Disk boot sector
protection. If this function is enabled and
someone attempt to write data into this area,
BIOS will show a warning message to on
screen and alarm beep.
Enabled
Display Full Screen LOGO during POST
Enabled
Disabled
Disabled
Configuration Table
Enable the Configuration Table function
Enabled
Quick Power On Self Test
This parameter speeds up POST by skipping
some items that are normally checked.
Enabled
Hard Disk Boot Priority
Select Hard Disk Boot Device Priority
Press [Enter]
First / Second / Third Boot
Device
The items allow you to set the sequence of boot
device where BIOS attempts to load the disk
operating system.
Floppy, LS120, Hard Disk, CD-ROM,
ZIP, USB-FDD, USB-ZIP, USB-CDROM,
USB-HDD, LAN, Disabled (Disable this
sequence).
Disabled
Disabled
The sequence following the order of
Floppy, HDD and CD-ROM is
recommended.
Chapter 2
25
Parameter
Options
Boot Other Device
This parameter allows you to specify the system
boot up search sequence.
Enabled
Boot Up NumLock Status
Sets the NumLock status when the system is
powered on. Setting to On will turn on the
NumLock key when the system is powered on.
Setting to Off will allows users to use the arrow
keys on the numeric keypad.
On
This item is to set the Gate A20 status. A20
refers to the first 64KB of extended memory.
When the default value Fast is selected, the
Gate A20 is controlled by port 92 or chipset
specific method resulting in faster system
performance. When Normal is selected, A20 is
controlled by a keyboard controller or chipset
hardware.
Fast
This field is used to enable or disable the APIC
(Advanced Programmable Interrupt Controller).
Due to compliance with PC2001 design guide,
the system is able to run in APIC mode.
Enabling APIC mode will expand available IRQ
resources from the system.
Enabled
Gate A20 Option
APIC Mode
26
Description
Disabled
Off
Normal
Disabled
Chapter 2
Advanced Chipset Features
CMOS Setup Utility-Copyright © 1984-2004 Award Software
Advanced Chipset Features
Configure DRAM Timing [Auto]
Item Help
x CAS Latency Setting
3T
Menu Level X
x DRAM RAS Active Time
9T
x DRAM RAS Precharge Time4T
DRAM timing and
x DRAM RAS to CAS Delay 4T
AGP Aperture Size
[64MB]
VGA Share Memory Size [32MB]
KLIJ: Move Enter: Select
F5: Previous Values
Parameter
+/-/PU/PD: Value F10:Save
F7: Default Settings
ESC: Exit
F1: General Help
Description
Configure DRAM Timing
This item is used to set memory controller.
CAS Latency TIme
When synchronous DRAM is installed, the
number of clock cycles of CAS latency
depends on the DRAM timing.
Options
Auto
Maunal
DRAM RAS Active Time
Control RAS active timing
DRAM RAS Precharge TIme
If an insufficient number of cycles is allowed
for the RAS to accumulate its charge before
DRAM refresh, the refresh may be
incomplete and the DRAM may fail to retain
data. Fast fives faster performance; and
Slow gives more stable performance.This
field applies only when synchronous DRAM
is installed in the syste.
DRAM RAS to CAS Latency
This field lets you insert a timing delay
between the CAS and RAS strobe signals,
used when DRAM is written to, read from, or
refreshed, Fast gives faster performance;
and Slow gives more stable performance.
This field applies only when synchronous
DRAM is installed in the system.
AGP Aperture Size
Setting AGP Aperture Size
VGA Share Memory SIze
Setting Share Memory SIze
Chapter 2
27
Power Management Setup
The Power Management menu lets you configure your system to most effectively save energy while operating
in a manner consistent with your own style of computer use.
The following screen shows the Power Management parameters and their default settings:
CMOS Setup Utility-Copyright © 1984-2004 Award Software
Power Management Setup
ACPI function
[Enabled]
Item Help
ACPI Suspend Type
[S3(STR)]
Menu Level X
Video Off Method
[V/H SYNC+Blank]
MODEM Use IRQ
[3]
HDD Power Down
[Disabled]
Soft-Off by PWR-BTTN
[Instant-off]
PWRON After PWR-Fail
[Former-Sts]
Power On by Ring
[Enabled]
Wake-Up by PCI Card
[Disabled]
Wake-Up by LAN
USB Device Wake-Up From S3 [Disabled]
Resume by Alarm
[Disabled]
x Month Alarm
NA
x Date ( of Month ) Alarm
Every day
x Time (hh:mm:ss) Alarm
00:00:00
KLIJ: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value F10:Save
F6: Fail-Save Default
ESC: Exit
F1: General Help
F7: Optimized Defaults
The following table describes the parameters found in this menu. Settings in boldface are the default and
suggested settings.
Parameter
ACPI Function
ACPI Suspend Type
28
Description
Options
This item is to activate the ACPI (Advanced
Configuration and Power Management Interface)
Function. If your operating system is ACPI
aware, such as Windows 98SE/2000/Me, select
Enabled.
Enabled
This item specifies the power saving modes for
ACPI function. S1(POS): The S1 sleep mode is a
low power state. In this state, no system context
(CPU or chipset) is lost and hardware maintains
all system context. S3 (STR): The S3 sleep
mode is s power-down state in which power is
supplied only to essential components such as
main memory and wake-capable devices and all
system context is saved to main memory. The
information stored in memory will be used to
restore the PC to the previous state when an
wake-up event occurs.
S1 (POS)
Disabled
S3 (STR)
Chapter 2
Parameter
Video Off Method
Video Off in Suspend
Description
Options
This item determines the manner in which the
monitor is blanked.
Blank Screen
V/H SYNC+Blank: This selection will cause the
system to turn off the vertical and horizontal
synchronization ports and write blanks to the
video buffer. Blank Screen: This option only write
blanks to the video buffer. DPMS Supported:
Initial display power management signaling.
DPMS
Enable Video Off in Suspend function
Enabled
V/H SYNC+Blank
Disabled
Modem Use IRQ
HDD Power Down
Soft-off by PWR-BTTN
PWRON After PWR-Fail
This setting names the interrupt request (IRQ)
line assigned to the modem (if any) on your
system. Activity of selected IRQ always awakens
the system.
Auto
This option is used to define the continuous HDD
idle time before the HDD enters power saving
mode. The setting values are disabled and 1 min
to 15 min.
Disabled
This option is used to set the power down
method. This function is only valid for systems
using an ATX power supply. When “instant off” is
selected, press the power switch to immediately
turn off power. When “delay 4 sec” is selected,
press and hole the power button for four seconds
to turn off power.
Instand Off
Soft-Off: Always in off state when AC back
Soft-Off
3,4,5,7,9,10,11
1,2,3,4,5,6,7,8,9,10,11,12,13,
14,15 Min
Delay 4 Sec.
Full-On: Always power on system when AC back Full-On
Power On by Ring
Former-Sts:System power on depends on the
status before AC lost.
Former-Sts
Enable power on by ring function.
Disabled
Enabled
Wake-Up by PCI Card
Enable PME Event Wake up.
Wake-Up by LAN
Enable Wake-Up by LAN function
Disabled
Enabled
Disabled
Enabled
USB Device Wake-Up From
S3
Enable USB Device Wake-Up from S3.
Resume by Alarm
Enable alarm function to power on system.
Enabled
Disabled
Disabled
Enabled
Chapter 2
29
Integrated Peripherals
CMOS Setup Utility-Copyright © 1984-2004 Award Software
Integrated Peripherals
USB 2.0 Support
[Enabled]
Item Help
USB Controller
[Enabled]
Menu Level X
USB Legacy Support
[Enabled]
USB Mouse Support
[Enabled]
Onboard LAN function [Enabled]
Onboard Parallel Port
[378/IRQ7]
Parallel Port Mode
[SPP]
x ECP Mode Use DMA
3
KLIJ: Move Enter: Select
F5: Previous Values
Parameter
USB 2.0 Support
+/-/PU/PD: Value F10:Save
F6: Fail-Save Default
ESC: Exit
F1: General Help
F7: Optimized Defaults
Description
Enable USB 2.0 function.
Option
Disabled
Enabled
USB Controller
Enable USB Controller.
Disabled
Enabled
USB Legacy Support
Enable USB Legacy
Disabled
USB Mouse Support
Enable USB Mouse Support.
Disabled
Enabled
Enabled
Onboard LAN function
Enable Onboard H/W LAN function.
Disabled
Onboard Parallel Port
Enable Onboard Parallel Port
Disabled
Enabled
378/IRQ7
278/IRQ5
3BC/IRQ7
Parallel Port Mode
Setting Parallel Port Mode
SSP
EPP
ECP
ECP+EPP
30
Chapter 2
PnP/PCI Configuration
CMOS Setup Utility-Copyright © 1984-2004 Award Software
PnP/PCI Configurations
Resources Controlled By
[Auto]
Item Help
x IRQ Resources
Press Enter
Menu Level X
KLIJ: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value F10:Save
F6: Fail-Save Default
ESC: Exit
F1: General Help
F7: Optimized Defaults
The following table describes the parameters found in this menu. Settings in boldface are the default and
suggested settings.
Parameter
Reset Configuration Data
IRQ Resources
Description
Selecting “Enabled” to reset Extended System
Configuration Data (ESCD) only if you installed
a new add-on and the system reconfiguration
has caused such a serious conflict that the
operating system can not boot. Otherwise, you
should leave it unchanged.
Options
Disabled
Enabled
The items are adjustable only when “Resources Press Enter
Controlled By” is set to Manual. By pressing
“Enter” to access the sub menu.
NOTE: It is strongly recommended that only experienced users should make any changes to the default
settings.
Chapter 2
31
PC Health Status
CMOS Setup Utility-Copyright © 1984-2004 Award Software
PC Health Status
Vcore
1.568V
Item Help
+ 3.3V
3.232V
Menu Level X
+5V
4.896V
-12V
11.731V
VDDQ
1.472V
3VDUAL
3.168V
o
System Temperature
43 C
CPU Temperature
59oC
CPU Fan Speed
2410 RPM
System Fan Speed
0 RPM
o
o
90 C/194 F
CPU Shutdown Temperatu
CPU Smart FAN Control
[Enabled]
CPU Smart FAN Control
[Enabled]
KLIJ: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value
F10:Save
F6: Fail-Save Default
ESC: Exit
F1: General Help
F7: Optimized Defaults
The following table describes the parameters found in this menu:
Parameter
Current Voltage(V)
Description
Options
Detect system’s voltage status automatically
Ambient Temperature
Detect Ambient temperature automatically
CPU Temperature
Detect CPU temperature automatically
CPU/SYSTEM Fan
Speed(RPM)
Detect CPU/SYSTEM Fan status automatically.
CPU Smart FAN
Control
Enable smart fan control function.
Enabled
--When the CPU temperature is higer than 65
degrees Celsius, CPU fan will run at full speed.
Disabled
--The speed of CPU fan will increase linearly
depand on the temperature if the temperature is
more than 41 degree and less than 65 degree.
--When the CPU temperature is lower than 40
degrees Celsius, CPU fan will be disable.
32
Chapter 2
Frequency Control
CMOS Setup Utility-Copyright © 1984-2004 Award Software
Frequency Control
Auto Detect DIMM/PCI Clk
[Enabled]
Item Help
SpreadSpectrum
[Enabled]
Menu Level X
KLIJ: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value
F10:Save
F6: Fail-Save Default
ESC: Exit
F1: General Help
The following table describes the parameters found in this menu. Settings in boldface are the default and
suggested settings.
Parameter
Auto Detect DIMM/PCI Clk
Description
Enable auto detect DIMM/PCI Clk Function.
Options
Disabled
Enabled
Spread Spectrum
Chapter 2
When the motherboard’s clock generator pulses,
the extreme values (spikes) of the pulses creates
EMI (Electromagnetic Interference). The spread
Spectrum function reduces the EMI generated by
modulating the pulses so that the spikes of the
pulses are reduced to flatter curves. If you do not
have any EMI problem, leave the setting at
Disabled for optimal system stability and
performance. But if you are plagued by EMI,
setting to Enabled for EMI reduction. Remember
to disable Spread Spectrum if you are
overlocking because even a slight jitter can
introduce a temporary boost in clockspeed which
may just cause your overlock ed processor to
lock up.
Disabled
Enabled
33
Load Default Settings
This option opens a dialog box that lets you install defaults for all appropriate items in the Setup Utility.
Press <Y> and then <Enter> to install the defaults. Press <N> and then <Enter> to not install the defaults. The
defaults place demands on the system that may be greater than the performance level of the components,
such as the CPU and the memory. You can cause fatal errors or instability if you install the optimized defaults
when your hardware does not support them. If you only want to install setup defaults for a specific option,
select and display that option.
34
Chapter 2
Set Supervisor/User Password
When this function is selected, the following message appears at the center of the screen to assist you in
creating a password.
Type the password, up to eight characters, and press <Enter>. The password typed now will clear any
previously entered password from CMOS memory. You will be asked to confirm the password. Type the
password again and press <Enter>. You may also press <Esc> to abort the selection.
To disable password, just press <Enter> when you are prompted to enter password. A message will confirm
the password being disabled. Once the password is disabled, the system will boot and you can enter BIOS
Setup freely.
Supervisor Password has higher priority than User Password. You can use Supervisor Password when
booting the system or entering BIOS Setup to modify all settings. Also you can use User Password when
booting the system or entering BIOS Setup but can not modify any setting if Supervisor Password is enabled.
Chapter 2
35
Save & Exit Setup
Highlight this item and press <Enter> to save the changes that you have made in the Setup Utility and exit the
Setup Utility.
When the Save and Exit dialog box appears, press <Y> to save the user setup value to RTC CMOS, or press
<N> to return to the main menu.
36
Chapter 2
Exit Without Saving
Highlight this item and press <Enter> to discard any changes that you have made in the Setup Utility and exit
the Setup Utility.
When the Exit Without Saving dialog box appears, press <Y> to discard changes and exit, or press <N> to
return to the main menu.
NOTE: If you have made settings that you do not want to save, use the "Exit Without Saving" item and press
<Y> to discard any changes you have made.
Chapter 2
37
Chapter 3
Machine Disassembly and Replacement
This chapter will guide you how to disassemble and reassemble Aspire T120E/AcerPower M2.
To disassemble the computer, you need the following tools:
T
Wrist grounding strap and conductive mat for preventing electrostatic discharge.
T
Wire cutter.
T
Phillips screwdriver (may require different size).
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatches when putting back the components.
Chapter 3
37
General Information
Before You Begin
Before proceeding with the disassenbly procedure, make sure that you do the following:
38
1.
Turn off the power to the system and all peripherals.
2.
Unplug the AC adapter and all power and signal cables from the system.
Chapter 3
Disassembly Flow Chart
Chapter 3
39
Standard Disassembly Procedure
This section tells you how to disassemble the system when you need to perform system service. Please also
refer to the disassembly video, if available.
CAUTION: Before you proceed, make sure you have turned off the system and all peripherals connected to it.
Opening the System
1.
Place the system unit on a flat, steady surface.
For AspireT120E:
For M2:
40
2.
Turn the housing back, and remove the two screws as shown here.
3.
Slide the side door out. Then remove it.
Chapter 3
Removing the Front Panel
1.
Remove the bezel by following the instruction below.
For Aspire T120E:
For AcerPower M2:
Removing the ODD/FDD/Card Reader/HDD
1.
Disconnect the CD-in cable from the ODD.
2.
Disconnect the ODD1 power cable and ODD1 cable form the ODD.
Chapter 3
41
42
3.
Disconnect the ODD2 power cable and ODD2 cable from the ODD.
4.
Disconnect the FDD power cable and the FDD cable from the FDD.
5.
Disconnect the HDD power cable and the HDD cable form the HDD.
6.
Press the ODD lock upward and detach the ODD from the frame.
7.
Press the FDD lock upward and detach the FDD from the frame.
Chapter 3
8.
Press the Card Reader lock and detach the Card Reader form the frame.
9.
Press the HDD lock upward and detach the HDD from the frame.
10. Remove the two screws on each side of Card Reader and then detach the Card Reader holder.
11. Remove the two screws on each side of HDD and then detach the HDD holder.
Chapter 3
43
Removing the Cables
44
1.
Disconnect the CD-In cable from Mainboard.
2.
Disconnect the FDD cable from the mainboard.
3.
Disconnect the IDE 1 and IDE 2 cables from mainboard.
4.
Disconnect the front panel audio connector form the mainboard.
5.
Disconnect the two USB connectors from the main board.
6.
Disconnect the system fan connector and the UPC fan connector from the main board.
Chapter 3
Removing the Power Supply
1.
Remove the main ATX power connector as shown here.
2.
Remove the ATX-12V power connector as shown here.
3.
Remove the four screws as shown here.
4.
Remove the power supply.
Removing the CPU fan ,CPU, and the System fan
1.
Disconnect the CPU fan connector from the mainboard.
Chapter 3
45
2.
Use a flat screwdriver to press the CPU fan latch.
3.
Pull the screwdriver toward the CPU fan and remove the CPU fan.
4.
Pull the CPU lever up to 90 degrees and remove the CPU then press down the CPU lever to the end.
5.
Remove the four screws holding the system fan.
6.
Take out the system fan.
Removing the Memory
1.
46
Press the leavers on the both sides of the DIMM socket outward to release the DIMM, and then gently pull
the DIMM out to remove it.
Chapter 3
Removing the VGA Card
1.
Remove the screw as shown here then take out the VGA card.
Removing the Modem Card
1.
,p
Remove the screw as shown here then take out the Modem Card.
Removing the Mainboard
1.
Remove the six screws as shown here. Then remove the mainboard.
Removing the Daughter Board
1.
Remove the screw as shown here.
Chapter 3
47
2.
48
Take out the daughter board and then detach the USB cable and audio cable from the daughter board.
Chapter 3
Chapter 4
Troubleshooting
This chapter provides troubleshooting information for the Aspire T120E/ AcerPower M2:
Chapter 4
T
Boot up Troubleshooting Flow Chart
T
Power-On Self-Test (POST)
T
POST Check Points
T
POST Error Messages List
T
Error Symptoms List
49
Boot up Troubleshooting Flow Chart
START
T urn off the power and unplug the AC power cable, then remove all
of the add-on cards and cables from motherboard.
Please make sure motherboard & chassis are not short ?
Yes
Please isolate
the short pin.
No
Failure hasbeen excluded.
Please make sure all jumper settings (such as CPU system bus
speed, frequency ratio, voltage and etc.) are set properly.
No
Make sure the
jumper setting
arecorrect.
Yes
Failure hasbeen excluded.
Check if the CPU cooling fan attached to CPU properly. ls
CPU cooling fan power connected to CPU_FAN
properly?
Yes
No
Plug the CPU
cooling fan pow er
in the CPU fan
connector. P lug in
the AC power
connector.
Failure hasbeen excluded.
No
Check if the memory install properly into the DIMM slot.
Insert and push
the memory
module vertically
into the DIMM slot.
Yes
Failure hasbeen excluded.
Insert the VGAcard. T hen plug in AT X power cable and
turn on the system.
A
50
Chapter 4
A
No
Is memory LED on and CPU fan running?
The problem c ould
be caused by
power supply , CPU,
memory or CPU/
memory sock et
itself.
Yes
Failure hasbeen excluded.
No
Check if there is display.
Perhaps y our VGA
card / VG A slot or
monitor is defec tiv e.
Yes
Failure hasbeen excluded.
T urn off the system. Reboot after keyboard and mouse
have been plugged in.
No
Check if keyboard is working properly.
It is poss ible that
y our k ey board or
key board connector
is defectiv e.
Yes
Press <Del> to enter BIOS setup. Choose "Load
Optimized Defaults" and save then exit setup.
T urn off the system and re-connect the IDE cable. Check
if the system can reboot successfully.
Failure hasbeen excluded.
No
The problem w as
probably caused by
the IDE dev ice /
connector or cable.
Yes
Reinstall Windows OS, and reinstall add-on cards and cables.
T hen try to reboot the system.
Failure hasbeen excluded.
END
Chapter 4
51
Power-On Self-Test (POST)
Before the computer can be used, all the components must be tested and initialized, and the operating system
must be bootstrapped into memory. This process is know as the power-on Self test(POST), generally under
the control of the BIOS.
The Power-On Self Test (POST) is a BIOS procedure that boots the system, initializes and diagnoses the
system components, and controls the operation of the power-on password option. During POST, system
reports test or initialization failure through Beep codes, display error messages on screen(if available), or LED.
The system halts when fatal error occurs.
The main components on the main board that must be diagnosed and/or initialized by POST to ensure system
functionality are as follows:
52
T
Microprocessor with built-in numeric co-processor and cache memory subsystem
T
Direct Memory Access (DMA) controller
T
Interrupt system
T
Three programmable timers
T
ROM subsystem
T
RAM subsystem
T
RTC RAM subsystem and real time clock/calendar with battery backup
T
Onboard serial interface controller
T
Onboard parallel interface controller
T
Embedded hard disk interface and one diskette drive interface
T
Keyboard and auxiliary device controllers
T
I/O ports
T
PS/2-compatible mouse port
T
PS/2-compatible keyboard port
T
Serial ports
T
Parallel ports
T
USB port
Chapter 4
POST Check Points
When POST executes a task, it uses a series of preset numbers called check point to be latched at port 80h,
indicating the stages it is currently running. This latch can be read and shown on a debug board.
The following table describes the Acer common tasks carried out by POST. A unique check point number
represents each task.
Checkpoint
Description
CFh
Test CMOS R/W functionality
C0h
Early chipset initialization:
•
•
•
C1h
Detect memory
•
•
Chapter 4
Disable shadow RAM
Disable L2 Cache (socket 7 or below)
Program basic chipset registers
Auto-detection of DRAM size, type and ECC.
Auto-detection of L2 cache (socket 7 or below)
C3h
Expand compressed BIOS code to DRAM
C5h
Call chipset hook to copy BIOS back to E000 & F000 shadow
RAM
0h1
Expand the Xgroup codes locating in physical address 1000:0
02h
Reserved
03h
Initial Superio_Early_Init switch
04h
Reserved
05h
1. Blank out screen
2. Clear CMOS error flag
06h
Reserved
07h
1. Clear 8042 interface
2. Initialize 8042 self-test
08h
1. Test special keyboard controller for Winbond 977 series
Super I/O chips
2. Enable keyboard interface
09h
Reserved
0Ah
1. Disable PS/2 mouse interface (optional)
2. Auto detect ports for keyboard & mouse followed by a port
& interface swap (optional)
3. Reset keyboard for Winbond 977 series Super I/O chips
0Bh
Reserved
0Ch
Reserved
0Dh
Reserved
0Eh
Test F000h segment shadow to see whether it is R/W-able or not.
If test fails. keep beeping the speaker.
0Fh
Reserved
10h
Auto detect flash type to load appropriate flash R/W codes into
the run time area in F000 for ESCD & DMI support.
11h
Reserved
53
Checkpoint
Description
12h
Use walking 1’s algorithm to check out interface in CMOS circuitry. Also set real-time clock power status, and then check for
override.
13h
Reserved
14h
Program chipset default values into chipset. Chipset default values are MODBINable by OEM customers.
15h
Reserved
16h
Initial onboard clock generator if Early_Init_Onboard_Generator
is defined. See also POST 26h.
17h
Reserved
18h
Detect CPU information including brand, SMI type (Cyrix or
Intel) and CPU level (586 or 686).
19h
Reserved
1Ah
Reserved
1Bh
Initial interrupts vector table. If no special specified, all H/W
interrupts are directed to SPURIOUS_INT_HDLR & S/W interrupts to SPURIOUS_soft_HDLR.
1Ch
Reserved
1Dh
Initial EARLY_PM_INIT switch
1Eh
Reserved
1Fh
Load keyboard matrix (notebook platform)
20h
Reserved
21h
HPM Initialization (notebook platform)
22h
Reserved
23h
1. Check validity of RTC value:
e.g. a value of 5Ah is an invalid value for RTC minute.
2. Load CMOS settings into BIOS stack. If Smos checksum
fails, use default value instead.
24h
Prepare BIOS resource map for PCI & PnP use. If ESCD is
valid, take into consideration of the ESCD’s legacy information.
25h
Early PCI Initialization:
•
•
•
54
Enumerate PCI bus number
Assign memory & I/O resource
Search for a valid VGA device & VGA BIOS, and put it into
C000:0
26h
1. If Early_Init_Onboard_Generator is not defined Onboard
clock generator initialization. Disable respective clock
resource to empty PCI & DIMM slots.
2. Init onboard PWM
3. Init onboard H/W monitor devices
27h
Initialize INT 09 buffer
28h
Reserved
29h
1. Program CPU internal MTRR (P6 & PII) for 0-640K memory address.
2. Initialize the APIC for Pentium class CPU
3. Program early chipset according to CMOS setup. Example:
onboard IDE controller.
4. Measure CPU speed.
Chapter 4
Checkpoint
Chapter 4
Description
2Ah
Reserved
2Bh
Invoke Video BIOS
2Ch
Reserved
2Dh
1. Initialize double-byte language font (Optional)
2. Put information on screen display, including Award title,
CPU type, CPU speed, full screen logo.
2Eh
Reserved
2Fh
Rederved
30h
Reserved
31h
Reserved
32h
Reserved
33h
Reset keyboard if Early_Reset_KB is defined e.g. Winbond 977
series Super I/O chips. See also POST 63h
34h
Reserved
35h
Test DMA Channel 0
36h
Reserved
37h
Test DMA Channel 1
38h
Reserved
39h
Test DMA page registers
3Ah
Reserved
3Bh
Reserved
3Ch
Test 8254
3Dh
Reserved
3Eh
Test 8259 interrupt mask bits for channel 1
3Fh
Reserved
40h
Test 8259 interrupt mask bits for channel 2
41h
Reserved
42h
Reserved
43h
Test 8259 functionality
44h
Reserved
45h
Reserved
46h
Reserved
47h
Initialize EISA slot
48h
Reserved
49h
1. Calculate total memory by testing the last double word of
each 64K page.
2. Program write allocation for AMD K5 CPU.
4Ah
Reserved
4Bh
Reserved
4Ch
Reserved
4Dh
Reserved
55
Checkpoint
4Eh
Description
1. Program MTRR of M1 CPU
2. Initialize L2 cache for P6 class CPU & program CPU with
proper cacheable range.
3. Initialize the APIC for P6 class CPU.
4. On MP platform, adjust the cacheable range to smaller one in
case the cacheable ranges between each CPU are not identical.
4Fh
Reserved
50h
Initialize USB Keyboard & Mouse
51h
Reserved
52h
Test all memory (clear all extended memory to 0)
53h
Clear password according to H/W jumper (Optional)
54h
Reserved
55h
Display number of processors (multi-processor platform)
56h
Reserved
57h
1. Display PnP logo
2. Early ISA PnP initialization - Assign CSN to every ISA PnP
device
58h
Reserved
59h
Initialize the combined Trend Anti-Virus code
5Ah
Reserved
5Bh
(Optional Feature)
Show message for entering AWDFLASH.EXE from FDD
(optional)
5Ch
Reserved
5Dh
1. Initialize Init_Onboard_Super_IO
2. Initialize Init_Onboard_AUDIO
5Eh
Reserved
5Fh
Reserved
60h
Okay to enter Setup utility; i.e. not until this POST stage can
users enter the CMOS setup utility.
61h
Reserved
62h
Reserved
63h
Reset keyboard if Early_Reset_KB is not defined.
64h
Reserved
65h
Initialize PS/2 Mouse
66h
Reserved
67h
Prepare memory size information for function call:
INT 15h ax=E820h
56
68h
Reserved
69h
Turn on L2 cache
6Ah
Reserved
6Bh
Program chipset registers according to items described in Setup
& Auto-configuration table
6Ch
Reserved
Chapter 4
Checkpoint
6Dh
Description
1. Assign resources to all ISA PnP devices.
2. Auto assign ports to onboard COM ports if the corresponding item in Setup is set to “Auto”.
6Eh
Reserved
6Fh
1. Initialize floppy controller
2. Set up floppy related fields in 40:hardware
70h
Reserved
71h
Reserved
72h
Reserved
73h
Reserved
74h
Reserved
75h
Detech &install all IDE device: HDD, LS120, ZIP, CDROM...
76h
(Optional feature)
Enter AWDFLASH.EXE if:
- AWDFLASH.EXE is found in floppy drive.
- ALT+F2 is prrssed.
77h
Detect serial ports & parallel ports
78h
Reserved
79h
Reserved
7Ah
Detect & install co-processor
7Bh
Reserved
7Ch
Init HDD write protect
7Dh
Reserved
7Eh
Reserved
7Fh
Switch back to text mode if full screen logo is supported.
- If errors occur, report errors & wait for keys
- If no errors occur or F1 key is pressed to continue:
Clear EPA or customization logo.
80h
Chapter 4
Reserved
81h
Reserved
82h
1. Call chipset power management hook.
2. Recover the text fond used by EPA logo (not for full screen
logo).
3. If password is set, ask for password.
83h
Save all data in stack back to CMOS
84h
Initialize ISA PnP boot devices
85h
1. USB final initialization
2. Switch screen back to text mode
86h
Reserved
87h
NET PC: Build SYSID structure
88h
Reserved
89h
1. Assign IRQs to PCI devices.
2. Set up ACPI table at top of the memory.
8Ah
Reserved
57
Checkpoint
58
Description
8Bh
1. Invoke all ISA adapter ROMs
2. Invoke all PCI ROMs (except VGA)
8Ch
Reserved
8Dh
1. Enable/Disable Parity Check according to CMOS setup.
2. APM Initialization
8Eh
Reserved
8Fh
Clear noise if IRQs
90h
Reserved
91h
Reserved
92h
Reserved
93h
Read HDD boot sector information for Trend Anti-Virus code
94h
1.
2.
3.
4.
5.
6.
7.
8.
Enable L2 cache
Program Daylight Saving
Program boot up speed
Chipset final initialization
Power management final initialization
Clear screen & dispaly summary table
Program K6 write allocation
Program P6 class write combining
95h
Update keyboard LED & typematic rate
96h
1.
2.
3.
4.
5.
FFh
Boot attempt (INT 19h)
Build MP table
Build & update ESCD
Set CMOS century to 20h or 19h
Load CMOS time into DOS timer tick
Build MSIRQ routing table
Chapter 4
POST Error Messages List
If you cannot run the diagnostics program tests but did receive a POST error message, use “POST Error
Messages List” to diagnose system problems. If you did not receive any error message, look for a description
of your error symptoms in “Error Sympton List”.
NOTE: When you have deemed it necessary to replace an FRU, and have done so, you must run a total
system check to ensure that no other activity has been affected by the change. This system check can
be done through the diagnostics program.
NOTE: Check all power supply voltages, switch, and jumper settings before you replace the main board. Also
check the power supply voltages if you have a “system no-power” condition.
NOTE: To diagnose a problem, first find the BIOS error messages in the left column. If directed to a check
procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the
first Action/FRU listed in right column is the most likely cause.
BIOS Messages
Action/FRU
I/O Parity Error
1. System board
CPU Clock Mismatch
1. Enter BIOS Setup and load the default settings.
2. Ensure BIOS setting for processor is set
correctly.
Real Time Clock Error
CMOS Battery Bad
CMOS Checksum Error
1. Enter BIOS Setup and load the default settings.
2. RTC Battery.
3. System Board.
Equipment Configuration Error
1. Ensure the system configuration set in BIOS
Setup is correct.
2. Enter BIOS Setup and load the default settings.
3. RTC battery.
4. System board.
System Management Memory Bad
Memory Error at MMMM:SSSS:OOOOh
1. Insert the memory modules in the DIMM sockets
properly, then reboot the system.
2. Memory module.
3. System board.
RAM Parity Error
1. Enter BIOS Setup to disable parity check.
2. Memory module
3. System board
PS/2 Keyboard Error or Keyboard Not
Connected
PS/2 Keyboard Interface Error
PS/2 Keyboard Locked
1.
2.
3.
4.
5.
Onboard xxx... Conflict(s)
1. Enter BIOS Setup and load the default settings.
2. Remove all adapter cards that are NOT factoryinstalled, then reboot the system.
Floppy Disk Controller Error
Floppy Drive A Error
Floppy Drive B Error
1. Diskette drive cable/connection.
2. Diskette drive.
3. System board
On Board Parallel Port Conflict(s)
On Board Serial Port 1 Conflict(s)
On Board Serial Port 2 Conflict(s)
1. Enter BIOS Setup and load the default settings.
2. Remove all adapter cards that are NOT factoryinstalled, then reboot the system.
Chapter 4
Re-connect PS/2 keyboard and mouse.
Enter BIOS Setup and load the default settings.
PS/2 keyboard
PS/2 mouse
System board
59
BIOS Messages
60
Action/FRU
Floppy Drive(s) Write Protected
Hard Disk Drive(s) Write Protected
1. Ensure that the diskette drive is not set to [Write
Protected] in the Security Options in BIOS
Setup.
2. Load default settings in Setup.
IDE Drive 0 Error
IDE Drive 1 Error
IDE Drive 2 Error
IDE Drive 3 Error
1.
2.
3.
4.
5.
IRQ Setting Error
Expansion ROM Allocation Fail
I/O Resource Conflict(s)
Memory Resource Conflict(s)
1. Load default settings in Setup.
2. Enter BIOS Setup and set the Reset
Resource Assignments of the PnP/PCI
Options to Yes, then reboot the system.
3. Remove all adapter cards that are NOT factoryinstalled, then reboot the system
PCI Device Error
1. Load default settings in Setup.
2. Enter BIOS Setup and set the Reset
Resource Assignments of the PnP/PCI
Options to Yes, then reboot the system.
3. Remove all adapter cards that are NOT factoryinstalled, then reboot the system.
PS/2 Pointing Device Interface Error
PS/2 Pointing Device Error
1.
2.
3.
4.
5.
Enter BIOS Setup and load the default settings.
Check IDE drive jumper.
IDE hard disk drive power.
IDE hard disk drive cable/connection.
IDE hard disk drive.
Re-connect PS/2 keyboard and mouse.
Enter BIOS Setup and load the default settings.
PS/2 mouse
PS/2 keyboard
System board
DMI Table Was Destroyed
1. Flash BIOS
Press “DEL” key to enter Setup or F1 key to
continue
1. Press DEL to enter Setup and reconfigure the
system.
Press ESC to turn off NMI, or any key to reboot
1. Press ESC to reject NMI error or press any other
key to reboot the system.
Insert system diskette and press ENTER key to
reboot
1. Insert a bootable disk into the floppy disk drive
or remove this disk if a hard disk is installed.
Chapter 4
Error Symptoms List
NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure,
replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/
FRU listed in right column is the most likely cause
.
Error Symptom
Action/FRU
Processor / Processor Fan
NOTE: Normally, the processor fan should be operative, and the processor clock setting should be
exactly set to match its speed requirement before diagnosing any processor problems.
Processor fan does not run but power
supply fan runs.
1. Ensure the system is not in power saving mode. See
“Power Management” in chapter 2.
2. With the system power on, measure the voltage of
processor fan connector. Its reading should be +12Vdc.
3. System board.
Processor test failed.
1. Processor
2. System board
System Board and Memory
NOTE: Ensure the memory modules are installed properly and the contact leads are clean before
diagnosing any system problems.
Memory test failed.
1. See "Memory"
2. System board
Incorrect memory size shown or
repeated during POST.
1. Insert the memory modules in the DIMM sockets properly,
then reboot the system.
2. Memory module.
3. System board.
System works but fails to enter power
saving mode when the Power
Management Mode is set to Enabled,
and power saving timer set in BIOS has
elapsed.
1. Enter BIOS Setup and load default settings.
In Windows 98, check settings in Power Management
Property of Control Panel.
2. Reload software from Recovery CD.
System hangs before system boot.
1. See "Index of Symptoms"
2. See "Undetermined Problems"
System hangs after system boot.
1. Execute a system test and set it to stop at “Halt on Error”
to see the potential cause of the problem.
2. See “Undetermined Problems”.
Blinking cursor only; system does not
work.
1.
2.
3.
4.
Diskette/IDE drive connection/cables
Diskette/IDE disk drives
See “Undetermined Problems”.
System board
Diskette Drive
NOTE: Ensure the diskette drive is configured correctly in BIOS Setup and its read/write head is
clean before diagnosing any diskette drive problems.
Media and drive are mismatched.
Chapter 4
1. Ensure the diskette drive is configured correctly in the
Disk Drives of BIOS Setup.
2. Ensure the diskette drive is correctly formatted.
3. Diskette drive connection/cable
4. Diskette drive
5. System board
61
Error Symptom
Action/FRU
Diskette drive does not work.
1. Ensure the diskette drive is not set to None in the Disk
Drives of BIOS Setup.
2. Diskette drive power
3. Diskette drive connection/cable
4. Diskette drive
5. System board
Diskette drive read/write error.
1. Diskette.
2. Ensure the diskette drive is not set to Write protect
in the Security Options of BIOS Setup.
3. Diskette drive cable.
4. Diskette drive.
5. System board.
Diskette drive LED comes on for more
than 2 minutes when reading data.
1.
2.
3.
4.
Diskette
Diskette drive connection/cable
Diskette drive
System board
Diskette drive LED fails to light, and the
drive is unable to access for more than 2
minutes.
1.
2.
3.
4.
5.
Diskette
Diskette drive power
Diskette drive connection/cable
Diskette drive
System board
Diskette drive test failed.
1.
2.
3.
4.
Diskette
Diskette drive
Diskette drive cable
System board
Hard Disk Drive
NOTE: Ensure hard disk drive is configured correctly in BIOS Setup, cable/jumper are set correctly
before diagnosing any hard disk drive problems.
Hard disk drive test failed.
1.
2.
3.
4.
Enter BIOS Setup and Load default settings.
Hard disk drive cable.
Hard disk drive.
System board.
Hard disk drive cannot format
completely.
1.
2.
3.
4.
Enter BIOS Setup and Load default settings.
Hard disk drive cable.
Hard disk drive.
System board.
Hard disk drive has write error.
1. Enter BIOS Setup and Load default settings.
2. Hard disk drive.
Hard disk drive LED fails to light, but
system operates normally.
1. With the system power on, measure the voltage of hard
disk LED connector.
2. Hard drive LED cable.
CD/DVD-ROM Drive
NOTE: Ensure CD/DVD-ROM drive is configured correctly in BIOS Setup, cable/jumper are set
correctly and its laser beam is clean before diagnosing any CD/DVD-ROM drive problems.
CD/DVD-ROM drive LED doesn't come
on but works normally.
62
1. CD/DVD-ROM drive
Chapter 4
Error Symptom
CD/DVD-ROM drive LED flashes for
more than 30 seconds before LED
shutting off.
Action/FRU
1. CD/DVD-ROM may have dirt or foreign material on it.
Check with a known good disc.
2. CD/DVD-ROM is not inserted properly.
3. CD/DVD-ROM is damaged.
Software asks to reinstall disc.
Software displays a reading CD/DVD
error.
CD/DVD-ROM drive cannot load or eject
when the system is turned on and its
eject button is pressed and held.
1. Disconnect all cables from CD/DVD-ROM drive except
power cable, then press eject button to try to unload the
disk.
2. CD/DVD-ROM drive power.
3. CD/DVD-ROM drive
CD/DVD-ROM drive does not read and
there are no messages are displayed.
1. CD may have dirt or foreign material on it. Check with a
known good disc.
2. Ensure the CD/DVD-ROM driver is installed properly.
3. CD/DVD-ROM drive.
CD/DVD-ROM drive can play audio CD
but no sound output.
1. Ensure the headphone jack of the CD/DVD-ROM has an
output.
2. Turn up the sound volume.
3. Speaker power/connection/cable.
4. CD/DVD-ROM drive.
Real-Time Clock
Real-time clock is inaccurate.
1. Ensure the information in the Date and Time of BIOS
Setup is set correctly.
2. RTC battery.
3. System board
Audio software program invokes but no
sound comes from speakers.
1. Speaker power/connection/cable.
Audio
Modem
Modem ring cannot wake up system
from suspend mode.
1. Ensure the Modem Ring Indicator in BIOS Setup or
Power Management is set to Enabled.
2. If PCI modem card is used, reinsert the modem card to
PCI slot firmly or replace the modem card.
3. If ISA modem card is used, ensure the modem ring-in
cable from the modem card to system board is connected
properly.
4. In Win 98, ensure the telephone application is configured
correctly for your modem and set to receive messages
and/or fax.
Data/fax modem software program
invokes but cannot receive/send data/
fax
1. Ensure the modem card is installed properly.
Fax/voice modem software program
invokes but has no sound output. (Data
files are received normally; voice from
modem cannot be produced, but system
sound feature works normally.)
1. Ensure the modem voice-in cable from modem adapter
card to system board
Video and Monitor
Video memory test failed.
Video adapter failed.
Chapter 4
1. Remove all non-factory-installed cards.
2. Load default settings (if screen is readable).
3. System board
63
Error Symptom
64
Action/FRU
Display problem:
- Incorrect colors
No high intensity
Missing, broken, or incorrect characters
Blank monitor(dark)
Blank monitor(bright)
Distorted image
Unreadable monitor
Other monitor problems
1.
2.
3.
4.
Display changing colors.
1. Monitor signal connection/cable
2. Monitor
3. System board
Display problem not listed above
(including blank or illegible monitor).
1. “Monitor".
2. Load default settings (if screen is readable).
3. System board
Monitor signal connection/cable.
Monitor
Video adapter card
System board
Chapter 4
Error Symptom
Action/FRU
Parallel/Serial Ports
Execute “Load BIOS Default Settings” in BIOS Setup to confirm ports presence before diagnosing any
parallel/serial ports problems.
Serial or parallel port loop-back test
failed.
1. Make sure that the LPT# or COM# you test is the same
as the setting in BIOS Setup.
2. Loop-back.
3. System board.
Printing failed.
1. Ensure the printer driver is properly installed. Refer to the
printer service manual.
2. Printer.
3. Printer cable.
4. System board.
Printer problems.
1. Refer to the service manual for the printer.
Keyboard
Some or all keys on keyboard do not
work.
1. Keyboard
Power Supply
Pressing power switch does not turn off
system. (Only unplugging the power
cord from electrical outlet can turn off the
system.)
1. Ensure the Power Switch < 4 sec. in BIOS Setup of
Power Management is not set to Suspend.
2. Power switch cable assembly
Pressing power switch does not turn on
the system.
1. Ensure the power override switch (situated at the back of
the machine, just above the connector for the power
cable) is not set to OFF.
2. Power switch cable assembly.
Executing software shutdown from
Windows98 Start menu does not turn off
the system. (Only pressing power switch
can turn off the system).
1. Load default settings.
2. Reload software from Recovery CD.
No system power, or power supply fan is
not running.
1. Power Supply
2. System Board
Other Problems
Any other problems.
Chapter 4
1. Undetermined Problems
65
Chapter 5
Jumper and Connector Information
Checking Jumper Settings
This section explains how to set jumpers for correct configuration of the mainboard.
Setting Jumpers
Use the mainboard jumpers to set system configuration options. Jumpers with more than one pir are
numbered. When setting the jumpers, ensure that the jumper caps are placed on the correct pins.
Jumper
Description
The illustrations below show a 2-pin
jumper. When the jumper cap is
placed on both pins, the jumper is
SHORT. If you remove the jumper
cap, or place the jumper cap on just
one pin, the jumper is OPEN.
Short
Open
This illustration shows a 3-pin
jumper. Pins1 and 2 are SHORT.
1 2
3
Chapter 5
66
I/O Back Panel Introduction
Item
Definition
Up: PS/2 Mouse Connector(6 pin Female)
Bottom:PS/2 Keyboard Connector(6 pin Female)
Up: Parallel Port(25 pin Female)
Bottom left: TV Out(7 pin Female)
Bottom right: VGA Port(15 pin Female)
COMA
VGA
USB0 and USB1 connector
USB 0
USB 1
LAN: Fast Ethernet with 10/100Mbps speed
USB2 and USB3 connector
LAN
USB 2
USB 3
67
Chapter 5
Item
Definition
Up: Line In
Middle: Line Out
Bottom: MIC In
Chapter 5
68
CONN & Jumper Settings
ATX_12V
Setting
1
3
2
4
Pin
Signal Name
1
GND
2
GND
3
+12V
4
+12V
ATX
Setting
10
1
69
20
11
Pin
Signal Name
1
3.3V
11
3.3V
2
3.3V
12
-12V
3
GND
13
GND
4
VCC
14
PS_ON(SoftOn/Off)
5
GND
15
GND
6
VCC
16
GND
7
GND
17
GND
8
PowerGood
18
-5V
9
5V SB(stand by +5V)
19
VCC
10
+12V
20
VCC
Chapter 5
IDE Connector
Setting
39
40
Chapter 5
Pin
1
2
Definition
Pin
Definition
1
IDERST
21
IDE REQ
2
GND
22
GND
3
Device data 7
23
I/O Write
4
Device data 8
24
GND
5
Device data 6
25
I/O READ
6
Device data 9
26
GND
7
Device data 5
27
I/O RDY
8
Device data 10
28
Pull down for
always master
9
Device data 4
29
IDE ACK
10
Device data 11
30
GND
11
Device data 3
31
IIDEIRQ
12
Device data 12
32
NC
13
Device data 2
33
Device address
1
14
Device data 13
34
NC
15
Device data 1
35
Device address
0
16
Device data 14
36
Device address
2
17
Device data 0
37
Device chip
select S1
18
Device data 15
38
Device chip
select S3
19
GND
39
HDDLED
20
NC
40
GND
70
Floppy Connecter
Setting
Pin
FLOPPY
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
FDC CON
Definitoin
Pin
Definition
1
GND
18
DIPJ
2
RWCJ
19
GND
3
NC
20
STEPJ
4
NC
21
GND
5
GND
22
WDJ
6
NC
23
GND
7
GND
24
WGATEJ
8
INDEXJ
25
GND
9
GND
26
TRK0J
10
MOAJ
27
GND
11
GND
28
WPJ
12
DSBJ
29
GND
13
GND
30
RDATAJ
14
DSAJ
31
GND
15
GND
32
HEADJ
16
MOBJ
33
GND
17
GND
34
DSKCHGJ
F_USB1/F_USB2(Front USB Connector, Yellow)
Setting
2
1
71
Pin
10
9
Signal Name
1
POWER
2
POWER
3
USB_DATAX-
4
USB_DATAy-
5
USB_DATAX+
6
USB_DATAy+
7
GND
8
GND
9
No Pin
10
NC
Chapter 5
Front Audio Connector
Setting
10
2
Pin
9
1
Pin Definition
1
MIC
2
GND
3
REF
4
POWER
5
Front/Audio(R)
6
Rear/Audio(R)
7
Reserved
8
No Pin
9
Front/Audio(L)
10
Rear/Audio(L)
CD_IN
Setting
Pin
Definition
1
CD L
2
CD GND
3
CD GND
4
CD R
1
FAN CONNECTER
Setting
Pin
Definition
1
GND
2
+12V
3
Sense
1
Chapter 5
72
Clear CMOS
Setting
Definition
Open:Normal
1
Close:Clear CMOS
1
COM
Setting
2
1
10
9
Pin
Definition
1
NDCDB-
2
NSINB
3
NSOUTB
4
NDTRB-
5
GND
6
NDSRB-
7
NRTSB-
8
NCTSB-
9
NRIB-
10
No Pin
F_USB_WK(Front USB Wake Up Function Jumper)
Setting
Pin
Definition
1-2
close
Enabled this
function(Default)
2-3
close
Disabled this function
1
1
73
Chapter 5
AUX_IN Connector
Setting
1
Pin
Definition
1
AUX-L
2
GND
3
GND
4
AUX-R
Set System Switch(CLK_SW)
Setting
ON
OFF
Definition
OFF: Auto(133/166/
200MHz, supports FSB
266/333/400MHz, default)
ON: 100MHz(support FSB
200MHz CPU)
ON
Chapter 5
OFF
74
Front Panel Switch/LED Connector
Intel standard front panel connector array:
Me s s a g e LED /Po w e r /
Sleep LED
Pow er Swi tch
MSGPW +
MSG+
PW -
2
10
9
1
ID E H ard Di sk
Ac tiv e L ED
NC
HD +
R ES+
HD-
RES-
Res et Swi tch
Function
75
Description
HD(IDE Hard Disk Active LED)
Pin1:LED anode(+)
Pin2:LED cathode(-)
RES(Reset Switch)
Open:Normal Ooperation
Close:Reset Hardware System
PW(Soft Power Connector)
Open:Normal Operation
Close:Power On/Off
MSG(MessageLED/Power/Sleep
LED)
Pin1:LED anode(+)
Pin2:LED cathode(-)
NC
NC
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of
Aspire T120E&AcerPower M2. Refer to this chapter whenever ordering for parts to repair or for RMA (Return
Merchandise Authorization).
Chapter 6
76
Exploded Diagram
Aspire T120E
˜˧˘ˠ
˄
˅
ˆ
ˇ
ˈ
ˉ
ˊ
ˋ
ˌ
˄˃
˄˄
˄˅
˄ˆ
˄ˇ
˄ˈ
77
˗˘˦˖˥˜ˣ˧˜ˢˡ
˜˧˘ˠ
VENT NET
˄ˉ
FRONT DECORAT PANE ˄ˊ
5.25" FILLER PANEL
˄ˋ
3.5" FILLER PANEL
˄ˌ
FRONT BAZEL
˅˃
TOP-DECOTAT PANEL
˅˄
POWER BUTTON
SWIRCH-HOLDER
SWIRCH CABLE
LED CABLE
LED HOLDER
CD-ROM/DVD-ROM
FDD-WITH-PANEL
USB BKT
USB BOARD
˗˘˦˖˥˜ˣ˧˜ˢˡ
HDD-BKT
TRACK(EN501C)
CHASSIS
POWER-SUPPLY
MOTHER BOARD
BKT-DOOR
Chapter 6
AcerPower M2
˜̇˸̀
˄
˅
ˆ
ˇ
ˈ
ˉ
ˊ
ˋ
ˌ
˄˃
˄˄
Chapter 6
˗˸̆˶̅˼̃̇˼̂́
˜̇˸̀
ˆˁˈʵʳ˙˜˟˟˘˥ʳˣ˔ˡ˘˟
˄˅
ˈˁ˅ˈʵʳ˙˜˟˟˘˥ʳˣ˔ˡ˘˟
˄ˆ
˙˥ˢˡ˧ʳ˕˘˭˘˟ʳˣ˔ˡ˘˟ʻˣ˔˜ˡ˧˘˗ʳ˔ˡ˗ʳ˦˜˟˞˘ ˄ˇ
ˣˢ˪˘˥ʳ˕˨˧˧ˢˡʻˣ˔˜ˡ˧˘˗ʼ
˄ˈ
ˣˢ˪˘˥ʳ˕˨˧˧ˢˡʳˣ˨˦˛ʳˣˢ˟˘
˄ˉ
˦ˣ˥˜ˡ˚
˄ˊ
˦˖˥˘˪ʳ˧ˆʽˋ
˄ˋ
˦˪˜˧˖˛ʳ˖˔˕˟˘
˄ˌ
˟˘˗ʳ˟˘ˡ˦
˅˃
˟˘˗ʳ˖˔˕˟˘
˅˄
˟˘˗ʳ˦˪˜˧˖˛ʳ˛ˢ˟˗˘˥
˗˸̆˶̅˼̃̇˼̂́
˖˗ˀ˥ˢˠ
˙˗˗ˀ˪˜˧˛ˀˣ˔ˡ˘˟
˨˦˕ʳ˕˞˧
˨˦˕ʳ˕ˢ˔˥˗
˛˗˗ˀ˕˞˧
˧˥˔˖˞ʻ˘ˡˈ˃˄˖ʼ
˖˛˔˦˦˜˦
ˣˢ˪˘˥ˀ˦˨ˣˣ˟ˬ
ˠˢ˧˛˘˥ʳ˕ˢ˔˥˗
˕˞˧ˀ˗ˢˢ˥
78
Parts
NOTE: Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel (http://aicsl.acer.com.tw/spl/, if you do not own a specific
account, you can still access the system with guest; guest). For whatever reasons a part number
change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE
PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list
of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to
order FRU parts for repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how best to dispose it, or follow the rules set by your regional Acer office on how to
return it.
Acer Aspire T120E&AcerPower M2
Pic
Partname
Description
Acer Part No.
BOARD
USB/AUDIO
DAUGHTER BOARD
FOXCONN
USB BOARD
55.PSPVF.001
READER
N/A
6-IN-1 CARD READER
MODULE 3.5 IN. BLACK
ECS UCR-61
6-IN-1 CARD READER MODULE
3.5 IN. BLACK ECS UCR-61
PZ.U6104.001
CABLES
79
SATA HDD CABLE
HDD DATA CABLE
50.PSPVF.001
IDE CD-ROM CABLE
ATA66 40PIN
CDROM DATA CABLE
50.PSPVF.002
IDE FDD CABLE 34PIN
FDD DATA CABLE
50.PSPVF.003
Chapter 6
Acer Aspire T120E&AcerPower M2
Pic
Partname
Description
Acer Part No.
AUDIO CABLE 8PIN
2CON
AUDIO CABLE
50.S03VF.001
FRONT INTERNAL USB
CABLE 10PIN 2CON
USB CABLE
50.S03VF.002
CASE/COVER/BRACKET ASSEMBLY
For Aspire T120E
FRONT BEZEL W/
POWER BUTTON, 5.25"
3.5" EMPTY COVER,
60.S14VF.001
FRONT COVER SILVER FRONT COVER SILVER
42.S14VF.005
POWER BUTTON
POWER BUTTON(PAINTED)
42.S14VF.001
SIDE DOOR
BKT-DOOR(PAINTING)
60.S14VF.002
N/A
CHASSIS W/0 I/O
SHIELD
K SERIAL CHASSIS ASSY
BLACK(W/ SIDE DOOR)
60.S14VF.003
N/A
I/O SHIELD
I/O SHIELD ASSY
PZ.S130A.002
N/A
RETENTION MODULE
RETENTION MODULE
42.S14VF.002
N/A
LED MODULE
LED HOLDER ASSY
42.S14VF.003
N/A
Chapter 6
BEZEL ASSY
80
Acer Aspire T120E&AcerPower M2
Pic
Partname
Description
Acer Part No.
N/A
SWITCH HOLDER
ASSY
SWITCH HOLDER ASSY
42.S14VF.004
N/A
EMPTY COVER FOR
5.25" DEVICE
5.25" FILLER PANEL
42.S03VF.004
HDD BRACKET
BKT-HDD
33.S14VF.001
FILLER COVER FOR 3
1/2" DEVICE
3.5" FILLER PANEL
42.S03VF.005
FRONT BEZEL W/
POWER BUTTON, 5.25"
3.5" EMPTY COVER,
BEZEL ASSY
60.P08VF.001
POWER BUTTON
POWER BUTTON(PAINTED)
42.P08VF.001
SIDE DOOR
BKT-DOOR(PAINTING)
60.S14VF.002
CHASSIS W/ SIDE
DOOR W/0 I/O SHIELD
K SERIAL CHASSIS ASSY
BLACK(W/ SIDE DOOR)
60.S14VF.003
N/A
For AcerPower M2
N/A
N/A
N/A
I/O SHIELD
I/O SHIELD ASSY
PZ.S130A.002
N/A
LED MODULE
LED-SWITCH HOLDER ASSY
42.P08VF.001
N/A
EMPTY COVER FOR
5.25" DEVICE
5.25" FILLER PANEL
42.S03VF.004
HDD BRACKET
BKT-HDD
33.S14VF.001
FILLER COVER FOR 3
1/2" DEVICE
3.5" FILLER PANEL
42.S03VF.005
N/A
FOOT STAND
N/A
81
RUBBER FOOT
RUBBER FOOT
47.S03VF.001
Chapter 6
Acer Aspire T120E&AcerPower M2
Pic
Partname
Description
Acer Part No.
CD-ROM DRIVE
N/A
CD-ROM DRIVE 52X
LITEON LTN-527T
BLACK
CD-ROM DRIVE 52X LITEON
LTN-527T BLACK
KD.05209.003
N/A
CD-ROM DRIVE 52X
BTC F564E BLACK
DRV,CD-ROM 52X,F564E BTC
(BLACK)
KD.0520A.001
CD-RW DRIVE
CD-RW DRIVE 52XR
32XRW 52XW LITEON
LTR-52327S BLACK
CD-RW DRIVE 52XR 32XRW
52XW LITEON LTR-52327S
BLACK
KR.03201.002
CD-RW DRIVE 52XR
32XRW 52XW BTC
5232IM BLACK
CD-RW DRIVE 52XR 32XRW
52XW BTC 5232IM BLACK
KR.0320A.002
CD-RW DRIVE 52XR
32XRW 52XW HLDS
GCE-8523B BLACK
CD-RW DRIVE 52XR 32XRW
52XW HLDS GCE-8523B BLACK
KR.0520C.001
COMBO DRIVE
N/A
COMBO DRIVE 52X
HLDS GCC-4521B
BLACK F/W:1.02
COMBO DRIVE 52X HLDS GCC4521B BLACK
KO.0520A.002
N/A
COMBO DRIVE 52X
BTC BCO-52161M
BLACK
COMBO DRIVE 52X BTC BCO52161M BLACK
KO.0520C.002
N/A
COMBO DRIVE 52X
LITEON SOHC-5232K
BLACK
COMBO DRIVE 52X LITEON
SOHC-5232K BLACK
KO.05209.002
DVD-ROM DRIVE
N/A
DVD-ROM DRIVE 16X
LITEON SOHD-167T
BLACK
DVD-ROM DRIVE 16X LITEON
SOHD-167T BLACK
KV.01604.003
N/A
DVD-ROM DRIVE 16X
HLDS GDR-8163B
BLACK
DVD-ROM DRIVE 16X HLDS
GDR-8163B BLACK
KV.0160D.003
N/A
DVD-ROM DRIVE 16X
BTC BDV 316E BLACK
DVD-ROM DRIVE 16X BTC BDV
316E BLACK
KV.0160A.002
DVD-ROM DRIVE 16X
PIONEER DVD-121RD
BLACK W/O ACER
LOGO
DRV,DVD-ROM 16X40X,DVD121RD PIONEER (BLACK)
KV.01605.003
DVD+RW DRIVE
N/A
SUPERMULTI PLUS
8XDVD HLDS GSA4082B FW A201 BLACK
8X DVD SUPERMULTI PLUS
(BLACK)
KU.0080D.002
FANSINK
Chapter 6
82
Acer Aspire T120E&AcerPower M2
Pic
N/A
Partname
Description
Acer Part No.
CPU FANSINK P4 478
FOR NORTHWOOD
2.8GHZ CPU (AND
BELOW)+FOXCONN
CPU 7015 FAN
PKP111G01K12
CPU FANSINK P4 478 FOR
NORTHWOOD 2.8GHZ CPU
(AND BELOW)+FOXCONN CPU
7015 FAN PKP111G01K12
CPU FANSINK FOR NW
3.4G AND PRESCOTT
2.8G-3.2G
Foxconn P4 478 fansink for
Northwood 3.4G and Prescott
2.8G-3.2G
HI.1920C.001
SYSTEM FAN
Foxconn 92x25 system fan for P4
Northwood 3.0Ghz (and above)
HI.9830C.001
CPU/PROCESSOR
N/A
CELERON 2.6GHZ/
400FSB/128K
(MULTIPLE VID)
SL6V3, RK80532RC064128
KC.DCD01.26A
N/A
CELERON 2.8G
SOCKET 478, D1
CELERON 2.8GHZ/400FSB/128K KC.DCD01.28A
N/A
CELERON 2.8GHZ/
533FSB/256K (PSC)
CELERON SL7DP,
RK80546RE088256
N/A
Celeron 330 (2.66G/
SL7DL, RK80546RE067256
256K/533FSB) (Prescott)
KC.D0001.330
N/A
Celeron 325 (2.53G/
SL7DK, RK80546RE061256
256K/533FSB) (Prescott)
KC.D0001.325
N/A
INTEL PENTIUM 4
2.8GHZ/1M/533FSB
(PSC)
SL7E2,RK80546PE0721
M
INTEL P4 2.8G
SL7E2,RK80546PE0721M
KC.DP001.28B
N/A
PRESCOTT 2.8GHZ /
1M / 800FSB
RK80546PG0721M
KC.DPD01.28C
N/A
PRESCOTT 3.0GHZ /
1M / 800FSB
RK80546PG0801M
KC.DPD01.30C
N/A
PRESCOTT 3.2GHZ /
1M / 800FSB
SL7B8, RK80546PG0881M
KC.DPD01.32C
KC.DCP01.28B
FDD/FLOPPY DISK DRIVE
N/A
FDD 1.44MB
PANASONIC JU256A198PC BLACK
FDD,PANASONIC,JU256A198PC BLACK
KF.25602.003
ADD-ON CARD
83
Chapter 6
Acer Aspire T120E&AcerPower M2
Chapter 6
Pic
Partname
Description
N/A
VGA CARD FX5200
256MB DDR W/TV OUT
(PAL), ATX BRACKET
PROLINK
VGA CARD FX5200 256MB DDR
W/TV OUT (PAL), ATX BRACKET
PROLINK
VG.52007.002
N/A
VGA CARD FX5200
256MB DDR W/TV OUT
(PAL), ATX BRACKET
PROLINK
VGA CARD FX5200 256MB DDR
W/TV OUT (PAL), ATX BRACKET
PROLINK
VG.52007.001
N/A
FX5700 128MB DDR W/
TV out + DVI (PAL), ATX
bracket
VG.57L0A.002
N/A
VGA CARD ATI
VGA CARD ATI RADEON
RADEON 9200SE
9200SE 128MB DDR W/TV-OUT
128MB DDR W/TVO/DVI + DVI (PAL), ATX BRACKET
(PAL) SAPHIRE ATX
BRACKET
54.ATI92.SE2
N/A
VGA CARD ATI
RADEON 9600SE
128MB DDR W/ TV out
(PAL), ATX bracket
54.ATI96.SE2
N/A
Radeon 9800SE
128MB(Hynix) W/TV out
+ DVI (PAL & NTSC)
ATX bracket
54.ATI98.SE3
N/A
Radeon 9550 128MB
64bit W/TV out + DVI
(PAL & NTSC) ATX
bracket
VG.9550B.001
N/A
VGA CARD FX-5200
128MB W/TV-OUT+DVI
(PAL) ATX BRACKET
LEADTEK LR2960 F/
W:4.3.5.1
N/A
FX5200 256MB DDR W/
TV out + DVI (PAL), ATX
bracket
VG.52004.001
N/A
FX5700 128MB DDR W/
TV out + DVI (PAL), ATX
bracket
VG.57L04.002
N/A
MODEM CARD HSF
V.92 56K, STANDARD
ATX BRACKET ASKEY
1456VQHT5 (INT1)
MODEM CARD HSF V.92 56K,
STANDARD ATX BRACKET
ASKEY 1456VQHT5 (INT1)
FX.14501.003
N/A
MODEM CARD ATX
GVC F1156I(+)/R12(EU)
MODEM CARD ATX GVC
FX.56I02.003
N/A
TUNER CARD VP3020C DTV-T CARD
WITH ATX BRACKET
TWINHAN
TUNER CARD VP-3020C DTV-T
CARD WITH ATX BRACKET
TWINHAN
TU.20C03.001
VGA CARD ATI RADEON
9600SE 128MB DDR W/ TV OUT
(PAL), ATX BRACKET
VGA FX-5200 LR2960 128MB W/
TV-OUT+DVI PAL
Acer Part No.
VG.29604.001
84
Acer Aspire T120E&AcerPower M2
Pic
N/A
Partname
TUNER CARD W/FM/
PAL/ATX BRACKET
(PHILIP MK3
TUNER+881 CHIP)
LEADTEK LR 6611
Description
TUNER CARD W/FM/PAL/ATX
BRACKET (PHILIP MK3
TUNER+881 CHIP) LEADTEK LR
6611
Acer Part No.
TU.61102.001
PIONTING DEVICE
N/A
CORDED MOUSE PS2 2 CORDED MOUSE PS2 2
BUTTON WHEEL
BUTTON WHEEL GENIUS
GENIUS NETSCROLL
NETSCROLL BLACK
BLACK
MS.PSE04.008
N/A
CORDED MOUSE USB
OPTICAL GENIUS
POWERSCROLL EYE
SILVER
GENIUS POWERSCROLL USB
OPTICAL WIRE ACER LOGO
SILVER
MS.PSE04.005
N/A
USB OPTICAL MOUSE
2
BUTTON+WHEEL(SILV
ER) M-UV ACR1
USB OPTICAL MOUSE 2
MS.MUV01.001
BUTTON+WHEEL(SILVER) M-UV
ACR1
PS/2 KEYBOARD
N/A
85
PS/2 KEYBOARD, KBP2971, US VER., 104KEYS
PS/2 KEYBOARD, KBP2971, T.CHINESE VER., 104KEYS
PS/2 KEYBOARD, KBP2971, ARABIC VER., 104KEYS
PS/2 KEYBOARD, KBP2971, THAI VER., 104KEYS
PS/2 KEYBOARD, KBP2971, SPANISH/US VER., 105KEYS
PS/2 KEYBOARD, KBP2971, INT'L US VER., 104KEYS
PS/2 KEYBOARD, KBP2971, CANADIAN/FRENCH VER.,
105KEYS
PS/2 KEYBOARD, KBP2971, BRAZILIAN VER., 107KEYS
PS/2 KEYBOARD, KBP2971, UK VER., 104KEYS
PS/2 KEYBOARD, KBP2971, FRENCH VER., 105KEYS
PS/2 KEYBOARD, KBP2971, GERMANY VER., 105KEYS
PS/2 KEYBOARD, KBP2971, ITALIAN VER., 105KEYS
PS/2 KEYBOARD, KBP2971, SWISS VER., 105KEYS
PS/2 KEYBOARD, KBP2971, SWEDISH VER., 105KEYS
PS/2 KEYBOARD, KBP2971, BELGIUM VER., 105KEYS
KB.KBP03.066
KB.KBP03.067
KB.KBP03.068
KB.KBP03.069
KB.KBP03.070
KB.KBP03.071
KB.KBP03.072
KB.KBP03.073
KB.KBP03.074
KB.KBP03.075
KB.KBP03.076
KB.KBP03.077
KB.KBP03.078
KB.KBP03.079
KB.KBP03.080
Chapter 6
Acer Aspire T120E&AcerPower M2
Pic
N/A
Chapter 6
Partname
Description
Acer Part No.
PS/2 KEYBOARD, KBP2971, DUTCH VER., 105KEYS
PS/2 KEYBOARD, KBP2971, HOLLAND VER., 105KEYS
PS/2 KEYBOARD, KBP2971, SPANISH VER., 105KEYS
PS/2 KEYBOARD, KBP2971, PORTUGESE VER., 105KEYS
PS/2 KEYBOARD, KBP2971, ICELAND VER., 105KEYS
PS/2 KEYBOARD, KBP2971, NORWEGIAN VER., 105KEYS
PS/2 KEYBOARD, KBP2971, HEBREW VER., 105KEYS
PS/2 KEYBOARD, KBP2971, POLISH VER., 105KEYS
PS/2 KEYBOARD, KBP2971, SLOVENIAN VER., 105KEYS
PS/2 KEYBOARD, KBP2971, SLOVAKIAN VER., 105KEYS
PS/2 KEYBOARD, KBP2971, TURKEY VER., 105KEYS
PS/2 KEYBOARD, KBP2971, RUSSIAMVER., 104KEYS
PS/2 KEYBOARD, KBP2971, HUNGARIA VER., 105KEYS
PS/2 KEYBOARD, KBP2971, GREEK VER., 104KEYS
PS/2 KEYBOARD, KBP2971, DENMARK VER., 105KEYS
KB.KBP03.081
KB.KBP03.082
KB.KBP03.083
KB.KBP03.084
KB.KBP03.085
KB.KBP03.086
KB.KBP03.087
KB.KBP03.088
KB.KBP03.089
KB.KBP03.090
KB.KBP03.091
KB.KBP03.092
KB.KBP03.093
KB.KBP03.094
KB.KBP03.095
PS/2 KEYBOARD, KBP2971, CZECH VER., 104KEYS
PS/2 KEYBOARD, KBP2971, US VER., 104KEYS, JAPAN
ABS BLACK
PS/2 KEYBOARD, KBP2971, ARABIC VER., 104KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, INT'L US VER., 104KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, UK VER., 104KEYS, JAPAN
ABS BLACK
PS/2 KEYBOARD, KBP2971, FRENCH VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, GERMANY VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, ITALIAN VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, SWISS VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, SWEDISH VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, BELGIUM VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, DUTCH VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, HOLLAND VER., 105KEYS,
JAPAN ABS BLAC
KB.KBP03.097
KB.KBP03.098
KB.KBP03.099
KB.KBP03.101
KB.KBP03.102
KB.KBP03.103
KB.KBP03.104
KB.KBP03.105
KB.KBP03.106
KB.KBP03.107
KB.KBP03.108
KB.KBP03.109
KB.KBP03.110
86
Acer Aspire T120E&AcerPower M2
Pic
N/A
Partname
Description
Acer Part No.
PS/2 KEYBOARD, KBP2971, SPANISH VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, PORTUGESE VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, ICELAND VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, NORWEGIAN VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, HEBREW VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, POLISH VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, SLOVENIAN VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, SLOVAKIAN VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, TURKEY VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, RUSSIAMVER., 104KEYS,
JAPAN ABS BLACK
KB.KBP03.111
PS/2 KEYBOARD, KBP2971, HUNGARIA VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, GREEK VER., 104KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, DENMARK VER., 105KEYS,
JAPAN ABS BLACK
PS/2 KEYBOARD, KBP2971, CZECH VER., 104KEYS,
JAPAN ABS BLACK
KB.KBP03.121
KB.KBP03.112
KB.KBP03.113
KB.KBP03.114
KB.KBP03.115
KB.KBP03.116
KB.KBP03.117
KB.KBP03.118
KB.KBP03.119
KB.KBP03.120
KB.KBP03.122
KB.KBP03.123
KB.KBP03.124
USB KEYBOARD
USB KB(SILVER), KU0355, US VER., 104KEYS
USB KB(SILVER), KU0355, T.CHINESE VER., 104KEYS
USB KB(SILVER), KU0355, INT'L US VER., 104 KEYS
USB KB (SILVER), KU0355, ARABIC VER., 104 KEYS
USB KB (SILVER), KU0355, THAI VER., 104 KEYS
USB KB (SILVER), KU0355, GERMANY VER., 105 KEYS
USB KB (SILVER), KU0355, ITALIAN VER., 105 KEYSUSB
KB (SILVER), KU0355, FRENCH VER., 105 KEYS
USB KB (SILVER), KU0355, SWEDEN VER., 105 KEYS
USB KB (SILVER), KU0355, UK VER., 104 KEYS
USB KB (SILVER), KU0355, SPANISH VER., 105 KEYS
87
KB.KUP03.034
KB.KUP03.035
KB.KUP03.036
KB.KUP03.037
KB.KUP03.038
KB.KUP03.039
KB.KUP03.040
KB.KUP03.041
KB.KUP03.042
KB.KUS03.001
KB.KUS03.002
Chapter 6
Acer Aspire T120E&AcerPower M2
Pic
Chapter 6
Partname
Description
Acer Part No.
USB KB (SILVER), KU0355, DUTCH VER., 105 KEYS
USB KB (SILVER), KU0355, PORTUGESE VER., 105 KEYS
USB KEYBOARD, KU0355, CANADIAN/FRENCH VER.,
105KEYS
USB KEYBOARD, KU0355, BRAZILIAN VER., 107KEYS
USB KEYBOARD, KU0355, SWISS VER., 105KEYS
USB KEYBOARD, KU0355, BELGIUM VER., 105KEYS
USB KEYBOARD, KU0355, ICELAND VER., 105KEYS
USB KEYBOARD, KU0355, NORWEGIAN VER., 105KEYS
USB KEYBOARD, KU0355, HEBREW VER., 105KEYS
USB KEYBOARD, KU0355, POLISH VER., 105KEYS
KB.KUS03.003
KB.KUS03.004
KB.KUS03.009
USB KEYBOARD, KU0355, SLOVENIAN VER., 105KEYS
USB KEYBOARD, KU0355, SLOVAKIAN VER., 105KEYS
USB KEYBOARD, KU0355, TURKEY VER., 105KEYS
USB KEYBOARD, KU0355, RUSSIAMVER., 104KEYS
USB KEYBOARD, KU0355, HUNGARIA VER., 105KEYS
USB KEYBOARD, KU0355, GREEK VER., 104KEYS
USB KEYBOARD, KU0355, DENMARK VER., 104KEYS
USB KEYBOARD, KU0355, CZECH, 104KEYS
USB KEYBOARD, KU-0355, IN'L US VER., 104KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, ARABIC VER., 104KEYS,
JAPAN ABS SLIVER+BLACK
KB.KUS03.018
KB.KUS03.019
KB.KUS03.020
KB.KUS03.021
KB.KUS03.022
KB.KUS03.023
KB.KUS03.024
KB.KUS03.058
KB.KUS03.063
USB KEYBOARD, KU-0355, GERMANY VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, ITALIAN VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, FRENCH VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, SWEDEN VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, UK VER., 104KEYS, JAPAN
ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, SPANISH VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, DUTCH VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, PORTUGESE VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, SWISS VER., 105KEYS, JAPAN
ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, BELGIUM VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
KB.KUS03.065
KB.KUS03.010
KB.KUS03.011
KB.KUS03.012
KB.KUS03.014
KB.KUS03.015
KB.KUS03.016
KB.KUS03.017
KB.KUS03.064
KB.KUS03.066
KB.KUS03.067
KB.KUS03.068
KB.KUS03.069
KB.KUS03.070
KB.KUS03.071
KB.KUS03.072
KB.KUS03.073
KB.KUS03.074
88
Acer Aspire T120E&AcerPower M2
Pic
Partname
Description
USB KEYBOARD, KU-0355, HOLLAND VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, ICELAND VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, NORWEGIAN VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, HEBREW VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, POLISH VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, SLOVENIAN VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, SLOVAKIAN VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, TURKEY VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, RUSSIAMVER., 104KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, HUNGARIA VER., 105KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, GREEK VER., 104KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, DENMARK VER., 104KEYS,
JAPAN ABS SLIVER+BLACK
USB KEYBOARD, KU-0355, CZECH VER., 104KEYS,
JAPAN ABS SLIVER+BLACK
Acer Part No.
KB.KUS03.075
KB.KUS03.076
KB.KUS03.077
KB.KUS03.078
KB.KUS03.079
KB.KUS03.080
KB.KUS03.081
KB.KUS03.082
KB.KUS03.083
KB.KUS03.084
KB.KUS03.085
KB.KUS03.086
KB.KUS03.087
MAINBOARD
MB G74M, SIS 741+SIS
964L, K7 462 PIN/
2DIMM/3PCI
GIGABYTE+I/O SHIELD
MB G74M, SIS 741+SIS 964L, K7
462 PIN/2DIMM/3PCI
GIGABYTE+I/O SHIELD
MB.S130A.004
MEMORY
89
Chapter 6
Acer Aspire T120E&AcerPower M2
Pic
N/A
Partname
Description
Acer Part No.
MEMORY DDR333 128MB 0.11U INFINEON
HYS64D16301GU-6-C
KN.12802.012
MEMORY DDR333 256MB 0.11U INFINEON
HYS64D32300GU-6-C
KN.25602.014
MEMORY DDR333 512MB 0.11U INFINEON
HYS64D64320GU-6-C
KN.51202.016
INFINEON DDR333 128MB 0.11U, CL=2.5
KN.12802.008
INFINEON DDR333 512MB 0.11U 64M*8 *8
KN.51202.008
MEMORY DDR 333 128MB/0.14U/16M*16*4 /NANYA
NT128D64SH4B1G-6K
KN.12803.005
MEMORY DDR333 256MB NANYA NT256D64S88B1G-6K
KN.25603.008
MEMORY DDR 333 512MB NANYA NT512D64S8HB1G-6K
KN.51203.004
MEMORY DDR 400 256MB 0.11U BLACK 32M*8*16 CL=3
INFINEON
KN.25602.018
MEMORY DDR 400 512MB 0.11U BLACK 32M*8*16 CL=3
INFINEON
KN.51202.018
MEMORY DDR 400 128MB 0.11U GREEN 16M*64
INFINEON HYS64D16301HU-5-C
KN.12802.011
MEMORY DDR 400 256MB INFINEON 32X8X9 CL3, 1.25"
INFINEON HYB25D256800CT-5
KN.25602.013
MEMORY DDR 400 512MB INFINEON 32X8X18 CL3, 1.25"
INFINEON HYB25D256800CT-5
KN.51202.012
NANYA DDR400 128MB
KN.12803.014
MEMORY DDR400 256MB NANYA NT256D64S88B1G-5T
EA
KN.25603.011
MEMORY DDR400 512MB NANYA NT512D64S8HB1G-5T
KN.51203.007
MEMORY DDR400 256MB 0.11U CL=3 MICRON
MT8VDDT3264AG-40BGB
KN.25604.013
MEMORY DDR400 256MB 0.11U CL=2.5 MICRON
MT4VDDT3264AG-40BC1
KN.25604.018
MEMORY DDR400 512MB 0.11U CL=3 MICRON
MT16VDDT6464AG-40BGB
KN.51204.011
POWER SUPPLY
POWER SUPPLY 230W
W/O PFC FSP FSP200ATV(A)
POWERSUPPLY-FSP230-60ATV
PY.23008.003
POWER SUPPLY 230W
W PFC FSP 200ATV(A)(PF)
POWERSUPPLY-FSP230-60ATV- PY.23008.004
PF
SCREWS
Chapter 6
90
Acer Aspire T120E&AcerPower M2
Pic
N/A
Partname
Description
Acer Part No.
M/B, USB BOARD
SCREW
SCREW M3*6(FOR M/B AND
USB)
86.PSPVF.001
FDD, CD-ROM SCREW
SCREW M3(FOR FDD AND CDROM)
86.PSPVF.002
CHASSIS SCREW
THUMB SCREW
86.S03VF.001
SPS SCREW
SCREW#6-32UNC(FOR SPS,
HDD AND CARD)
86.PSPVF.004
SPEAKER
N/A
SPEAKER USB 3" *2
NEOSONICA 510
THYME510 WHITE
SPEAKER,USB 3" *2,
510,NEOSONICA
SP.51004.001
SPEAKER USB 3" *2
NEOSONICA
THYME510 BLACK
SPEAKER,USB 3"FULL RANG
CONE,THYME510
SP.51004.003
HDD/HARD DISK DRIVE
N/A
HDD 80GB 7200RPM SATA SEAGATE ALPINE
ST380013AS
KH.08001.005
HDD 120G 7200RPM SATA SEAGATE ALPINE
ST3120026AS
KH.12001.005
HDD 160G 7200RPM SATA SEAGATE ALPINE
ST3160023AS
KH.16001.004
HDD 80GB 7200RPM SATA WDD XL80SD WD800JD22HKA0
KH.08008.007
HDD 120GB 7200RPM SATA WD WD1200JD-22HB
KH.12008.007
HDD 160GB 7200RPM SATA WD WD1600JD-22HB
KH.16008.007
HDD 200GB 7200RPM SATA WD WD2000JD-22HB
KH.20008.007
HDD 250GB 7200RPM SATA WD WD2500JD-22HB
KH.25008.006
HDD 3.5 IN. 40GB 5400RPM WD 400EB-11JEF0, 2M, FDB
KH.04008.005
HDD 3.5 IN. 80GB 5400RPM WD 800EB-11JEF0
KH.08008.005
HDD 40GB 7200RPM WD XL80SD WD400BB-22FJA0
KH.04008.006
HDD 80GB 7200RPM WD XLS80SD WD800BB-22FJA0 F/W
A0
KH.08008.006
HDD 120GB 7200RPM WD XL80 WD1200BB-22FTA0
KH.12008.003
HDD 160GB 7200RPM WD XL80 WD1600BB-22FTA0
KH.16008.003
HDD 200GB 7200RPM WD XL80 WD2000BB-22FTA0
KH.20008.003
HDD 250GB 7200RPM WD XL80 WD2500BB-22FTA0
KH.25008.002
HDD 120GB 7200RPM WD XL80II WD1200BB-22GUA0 2MB KH.12008.006
FDB
HDD 160GB 7200RPM WD XL80II WD1600BB-22GUA0 2MB KH.16008.006
FDB
HDD 200GB 7200RPM WD XL80II WD2000BB-22GUA0 2MB KH.20008.006
FDB
HDD 250GB 7200RPM WD XL80II WD2500BB-22GUA0 2MB KH.25008.005
FDB
91
HDD 40GB 7200RPM SEAGATE ALPINE/BPA ST340014A
KH.04001.011
HDD 80GB 7200RPM SEAGATE ALPINE/BPA ST380011A
KH.08001.008
Chapter 6
Acer Aspire T120E&AcerPower M2
Pic
Partname
Description
Acer Part No.
HDD 120GB 7200RPM SEAGATE ALPINE/BPA ST3120022A KH.12001.010
HDD 160GB 7200RPM SEAGATE ALPINE/BPA ST3160021A KH.16001.009
Chapter 6
92
93
Chapter 6
Appendix A
Model Definition and Configuration
The Aspire T120E/AcerPower M2 Model No. Define:
1.
Trade Mark:
2.
Brand Name: Acer
3.
Description: SiS741+SiS964L, K7462pin / 2DIMM / 3PCI
4.
Model No: K4.2
5.
Product Name: Aspire T120E/ AcerPower M2
Appendix A
93
94
Appendix A
Appendix B
Test Compatible Components
Aspire T120E/ AcerPower M2 compatibility is tested and verified by Acer’s internal testing department. All of
its system functions are tested under the environments of Windows XP Home.
Appendix B
94
Microsoft Windows XP Home Environment Test
COMPONENTS
SPEC.
MODEL DESCRIPTION
ACER PART No.
MAINBOARD/IO Bracket/MB kit
Gigabyte
SiS 741 + SiS 964L, K7 462 pin/
2DIMM/3PCI
G74M
MB.S130A.003
MAINBOARD Kit
Gigabyte
G74M + I/O bracket
MB.S130A.004
I/O Bracket
Gigabyte
I/O bracket for G74M
PZ.S130A.002
Housing Kit
H602 housing PFC/FDD for AcerPower
M2
HS.P080D.001
H602 housing PFC W/O FDD for
AcerPower M2
HS.P080D.002
H602 housing PFC/FDD for Aspire
T120E
HS.S160D.001
H602 housing PFC W/O FDD for Aspire
T120E
HS.S160D.002
CPU FAN
Foxconn
PKP145G01K12
PKP145G01K12
HI.1450C.001
PV983DG3BC6511
HI.9830C.001
Athlon XP 2600+ (Barton)
333MHz, 256KB L2
KC.A2602.BXP
Athlon XP 2800+ (Barton)
2.08GHz, 333MHz,
512KB L2
KC.A2802.0XP
Athlon XP 3000+ (Barton)
2.17GHz, 333MHz,
512KB L2
KC.A3002.0XP
Athlon XP 3000+ (Barton)
400MHz, 512KB L2
KC.A3002.BXP
Athlon XP 3200+ (Barton)
400MHz, 512KB L2
KC.A3202.0XP
System Fan
Foxconn
System Fan, 92x92x25, 3400rpm, CS
Bearing 550+/-10mm
CPU(333Mhz)
AMD
CPU(400Mhz)
AMD
DIMM(DDR 333)
Infineon
95
DDR 333 128MB 0.11u(black)
HYS64D16301GU-6- KN.12802.012
C
DDR 333 256MB 0.11u(black)
HYS64D32300GU-6- KN.25602.014
C
DDR 333 512MB 0.11u(black)
HYS64D64320GU-6- KN.51202.016
C
Appendix B
COMPONENTS
SPEC.
MODEL DESCRIPTION
ACER PART No.
DDR 333 128MB 0.11u
HYS64D16301HU-6- KN.12802.008
C
DDR 333 512MB 0.11u
HYS64D64320HU-6- KN.51202.008
C
DDR 333 128MB 0.14u 16M*16*4 NT128D64SH4B1G- KN.12803.005
6K
Nanya
DDR 333 256MB 0.14u 32M*8*8
NT256D64S88B1G6K
KN.25603.008
DDR 333 512MB 0.14u 32M*8*16 NT512D64S8HB1G- KN.51203.004
6K
DIMM(DDR 400)
Infineon
Nanya
Micron
DDR400 256MB 0.11u (Black)
32M*8*16 CL=3
KN.25602.018
DDR400 512MB 0.11u (Black)
32M*8*16 CL=3
KN.51202.018
DDR 400 512MB
HYS64D64320GU-5- KN.51202.006
B
DDR400 128MB
NT128D64SH4B1G- KN.12803.014
5T
DDR400 256MB
NT256D64S88B1G5T
KN.25603.011
DDR400 512MB
NT512D64S8HB1G
KN.51203.007
Micron DDR 400 256MB, 0.11u CL MT8VDDT3264AG=3
40BGB
KN.25604.013
Micron DDR 400 512MB, 0.11u CL MT16VDDT6464AG- KN.51204.011
=3
40BGB
HDD (P-ATA/5400RPM)
WD
Protégé XL80SD 40G 5400RPM,
ATA-100
WD400EB-11JEF0
KH.04008.005
Protégé XL80SD 80G 5400RPM,
ATA-100
WD800EB-11JEF0
KH.08008.005
HDD (P-ATA/7200RPM)
WD
Appendix B
Caviar XL80SD 40G 7200RPM,
ATA-100
WD400BB-22FJA0
KH.04008.006
Caviar XL80SD 80G 7200RPM,
ATA-100
WD800BB-22FJA0
KH.08008.006
XL80 120G 7200RPM
WD1200BB-22FTA0 KH.12008.003
XL80 160GB 7200RPM
WD1600BB-22FTA0 KH.16008.003
96
COMPONENTS
SPEC.
MODEL DESCRIPTION
XL80 200GB 7200RPM
ACER PART No.
WD2000BB-22FTA0 KH.20008.003
XL80 250GB 7200RPM
Seagate
XL80II 120G 7200rpm,
WD1200BB-22GUA0 2MB FDB
WD1200BB-22GUA0 KH.12008.006
XL80II 160G 7200rpm,
WD1600BB-22GUA0 2MB FDB
WD1600BB-22GUA0 KH.16008.006
XL80II 200G 7200rpm,
WD2000BB-22GUA0 2MB FDB
WD2000BB-22GUA0 KH.20008.006
XL80II 250G 7200rpm,
WD2500BB-22GUA0 2MB FDB
WD2500BB-22GUA0 KH.25008.005
Alpine/BPA 40G 7200RPM, ATA100
ST340014A
KH.04001.011
Alpine/BPA 80G 7200RPM, ATA100
ST380011A
KH.08001.008
Alpine/BPA 120G 7200RPM, ATA100
ST3120022A
KH.12001.010
Alpine/BPA 160G 7200RPM, ATA100
ST3160021A
KH.16001.009
VGA Card
Prolink
Sapphire
97
FX5200 128MB DDR W/TV out + DVI
(PAL), ATX bracket
VG.52007.002
FX5200 256MB DDR W/TV out + DVI
(PAL), ATX bracket
VG.52007.001
FX5700 128MB DDR W/ TV out +
DVI (PAL), ATX bracket
VG.57L0A.002
Radeon 9200SE 128MB(Mezza),W/TVout + DVI (PAL & NTSC) ATX bracket
54.ATI92.SE2
Radeon 9600SE 128MB(Hynix
memory), W/TV out + DVI (PAL&
NTSC) ATX bracket
54.ATI96.SE2
Radeon 9800SE 128MB(Hynix) W/TV
out + DVI (PAL & NTSC) ATX bracket
54.ATI98.SE3
Radeon 9550 128MB 64bit W/TV out +
DVI (PAL & NTSC) ATX bracket
VG.9550b.001
Appendix B
COMPONENTS
Leadtek
SPEC.
MODEL DESCRIPTION
ACER PART No.
FX5200 128MB DDR W/ TV out +
DVI (PAL), ATX bracket
LR2960 PCB:B, Ass
Rev.:A
VG.29604.001
FX5200 256MB DDR W/ TV out +
DVI (PAL), ATX bracket
VG.52004.001
FX5700 128MB DDR W/ TV out +
DVI (PAL), ATX bracket
VG.57L04.002
CD-ROM
Lite-On
52X CD-ROM
LTN-527T(black)
KD.05209.003
BTC
52X CD-ROM
F564E (black)
KD.0520A.001
HLDS
CD-RW
Lite-On
BTC
HLDS
52X/32X/52X CD-RW
LTR-52327S (black) KR.03201.002
52x32x52 CD-RW
5232IM(black)
KR.0320A.002
52X/32X/52X
GCE-8525B(black)
KR.0520C.001
DVD ROM
Lite-On
16X DVD-ROM
SOHD-167T(black)
KV.01604.003
HLDS
16X/52X
GDR-8163B(black)
KV.0160D.003
BTC
16X/40X
BDV 316E(black)
KV.0160A.002
KO.0520A.002
Combo
HLDS
52X Combo
GCC-4521B(black)
BTC
52X Combo
BCO-5216IM(black) KO.0520C.002
HLDS
52X Combo
SOHC-5232K(black) KO.05209.002
SuperMultiPlus
HLDS
8X DVD SuperMulti Plus(black)
GSA-4082B(black)
KU.0080D.002
Modem Card
GVC
F-1156I(+)/R12-AAP
FX.56I02.003
Housing
Foxconn
Microtower/
3*3.5"+2*5.25"(black)
H602 housing
HS.S030D.001
SPS
FSP
FSP200-ATV(A)(PF), 230W PFC
SPS
FSP200-60ATV(A)(PF) PY.23008.004
FDD
1.44M 3.5"(black)
JU-256A198PC
KF.25602.003
Daughter Board
Foxconn
Appendix B
USB/Audio daughter board
TBD
98
COMPONENTS
SPEC.
MODEL DESCRIPTION
ACER PART No.
Media Card Reader
ECS
3.5" (black) 6-in-1 card reader
UCR-61
PZ.U6104.001
LR 6611
TU.61102.001
TV Tuner Card
Leadtek
Tuner Card w/FM/PAL/ATX Bkt (Philip
MK3 Tuner + 881 chip)
Digital TV Tuner Card
TwinHan
TV Tuner Card VP-3020C DTV-T
card with ATX bracket
VP-3020C
TU.20C03.001
Keyboard
Chicony
99
PS/2 Keyboard, KBP2971, US Ver., Chicony KB
104keys
2971(black)
KB.KBP03.06
6
PS/2 Keyboard, KBP2971,
T.Chinese Ver., 104keys
Chicony KB
2971(black)
KB.KBP03.06
7
PS/2 Keyboard, KBP2971, Arabic
Ver., 104keys
Chicony KB
2971(black)
KB.KBP03.06
8
PS/2 Keyboard, KBP2971, Thai
Ver., 104keys
Chicony KB
2971(black)
KB.KBP03.06
9
PS/2 Keyboard, KBP2971,
Spanish/US Ver., 105keys
Chicony KB
2971(black)
KB.KBP03.07
0
PS/2 Keyboard, KBP2971, Int'l US
Ver., 104keys
Chicony KB
2971(black)
KB.KBP03.07
1
PS/2 Keyboard, KBP2971,
Canadian/French Ver., 105keys
PS/2 Keyboard, KBP2971,
Brazilian Ver., 107keys
Chicony KB
2971(black)
KB.KBP03.07
2
Chicony KB
2971(black)
KB.KBP03.073
PS/2 Keyboard, KBP2971, UK Ver., Chicony KB
104keys
2971(black)
KB.KBP03.07
4
PS/2 Keyboard, KBP2971, French
Ver., 105keys
Chicony KB
2971(black)
KB.KBP03.07
5
PS/2 Keyboard, KBP2971,
Germany Ver., 105keys
Chicony KB
2971(black)
KB.KBP03.07
6
PS/2 Keyboard, KBP2971, Italian
Ver., 105keys
Chicony KB
2971(black)
KB.KBP03.07
7
Appendix B
COMPONENTS
Appendix B
SPEC.
MODEL DESCRIPTION
ACER PART No.
PS/2 Keyboard, KBP2971, Swiss
Ver., 105keys
Chicony KB
2971(black)
KB.KBP03.07
8
PS/2 Keyboard, KBP2971,
Swedish Ver., 105keys
Chicony KB
2971(black)
KB.KBP03.07
9
PS/2 Keyboard, KBP2971,
Belgium Ver., 105keys
Chicony KB
2971(black)
KB.KBP03.08
0
PS/2 Keyboard, KBP2971, Dutch
Ver., 105keys
Chicony KB
2971(black)
KB.KBP03.08
1
PS/2 Keyboard, KBP2971, Holland
Ver., 105keys
Chicony KB
2971(black)
KB.KBP03.08
2
PS/2 Keyboard, KBP2971, Spanish
Ver., 105keys
Chicony KB
2971(black)
KB.KBP03.08
3
PS/2 Keyboard, KBP2971, Portugese
Ver., 105keys
Chicony KB
2971(black)
KB.KBP03.08
4
PS/2 Keyboard, KBP2971, Iceland
Ver., 105keys
Chicony KB
2971(black)
KB.KBP03.08
5
PS/2 Keyboard, KBP2971, Norwegian
Ver., 105keys
Chicony KB
2971(black)
KB.KBP03.08
6
PS/2 Keyboard, KBP2971, Hebrew
Ver., 105keys
Chicony KB
2971(black)
KB.KBP03.08
7
PS/2 Keyboard, KBP2971, Polish Ver., Chicony KB
105keys
2971(black)
PS/2 Keyboard, KBP2971, Slovenian
Chicony KB
Ver., 105keys
2971(black)
PS/2 Keyboard, KBP2971, Slovakian
Chicony KB
Ver., 105keys
2971(black)
PS/2 Keyboard, KBP2971, Turkey Ver., Chicony KB
105keys
2971(black)
PS/2 Keyboard, KBP2971,
Chicony KB
RussiamVer., 104keys
2971(black)
PS/2 Keyboard, KBP2971, Hungaria
Chicony KB
Ver., 105keys
2971(black)
PS/2 Keyboard, KBP2971, Greek Ver., Chicony KB
104keys
2971(black)
PS/2 Keyboard, KBP2971, Denmark
Chicony KB
Ver., 105keys
2971(black)
KB.KBP03.08
8
KB.KBP03.08
9
KB.KBP03.09
0
KB.KBP03.09
1
KB.KBP03.09
2
KB.KBP03.09
3
KB.KBP03.09
4
KB.KBP03.09
5
100
COMPONENTS
SPEC.
MODEL DESCRIPTION
PS/2 Keyboard, KBP2971, Czech Ver., Chicony KB
104keys
2971(black)
PS/2 Keyboard, KBP2971, US Ver.,
Chicony KB
104keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Arabic Ver., Chicony KB
104keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Int'l US
Chicony KB
Ver., 104keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, UK Ver.,
Chicony KB
104keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, French
Chicony KB
Ver., 105keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Germany
Chicony KB
Ver., 105keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Italian Ver., Chicony KB
105keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Swiss Ver., Chicony KB
105keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Swedish
Chicony KB
Ver., 105keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Belgium
Chicony KB
Ver., 105keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Dutch Ver., Chicony KB
105keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Holland
Chicony KB
Ver., 105keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Spanish
Chicony KB
Ver., 105keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Portugese Chicony KB
Ver., 105keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Iceland
Chicony KB
Ver., 105keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Norwegian Chicony KB
Ver., 105keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Hebrew
Chicony KB
Ver., 105keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Polish Ver., Chicony KB
105keys, Japan ABS
2971(black)
101
ACER PART No.
KB.KBP03.09
7
KB.KBP03.09
8
KB.KBP03.09
9
KB.KBP03.10
1
KB.KBP03.102
KB.KBP03.103
KB.KBP03.104
KB.KBP03.105
KB.KBP03.106
KB.KBP03.107
KB.KBP03.108
KB.KBP03.109
KB.KBP03.110
KB.KBP03.111
KB.KBP03.112
KB.KBP03.113
KB.KBP03.114
KB.KBP03.115
KB.KBP03.116
Appendix B
COMPONENTS
Appendix B
SPEC.
MODEL DESCRIPTION
ACER PART No.
PS/2 Keyboard, KBP2971, Slovenian
Ver., 105keys, Japan ABS
Chicony KB
2971(black)
KB.KBP03.117
PS/2 Keyboard, KBP2971, Slovakian
Ver., 105keys, Japan ABS
Chicony KB
2971(black)
KB.KBP03.118
PS/2 Keyboard, KBP2971, Turkey Ver., Chicony KB
105keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971,
Chicony KB
RussiamVer., 104keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Hungaria
Chicony KB
Ver., 105keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Greek Ver., Chicony KB
104keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Denmark
Chicony KB
Ver., 105keys, Japan ABS
2971(black)
PS/2 Keyboard, KBP2971, Czech Ver., Chicony KB
104keys, Japan ABS
2971(black)
KB.KBP03.119
KB.KBP03.120
KB.KBP03.121
KB.KBP03.122
KB.KBP03.123
KB.KBP03.124
102
COMPONENTS
Chicony
103
SPEC.
MODEL DESCRIPTION
ACER PART No.
Chicony
KU0355(silver)
KB.KUP03.034
USB Keyboard, KU0355, T.Chinese Chicony
Ver., 104keys
KU0355(silver)
KB.KUP03.035
USB Keyboard, KU0355, In'l US
Ver., 104keys
Chicony
KU0355(silver)
KB.KUP03.036
USB Keyboard, KU0355, Arabic
Ver., 104keys
Chicony
KU0355(silver)
KB.KUP03.037
USB Keyboard, KU0355, Thai Ver., Chicony
104keys
KU0355(silver)
KB.KUP03.038
USB Keyboard, KU0355, Germany Chicony
Ver., 105keys
KU0355(silver)
KB.KUP03.039
USB Keyboard, KU0355, Italian
Ver., 105keys
Chicony
KU0355(silver)
KB.KUP03.040
USB Keyboard, KU0355, French
Ver., 105keys
Chicony
KU0355(silver)
KB.KUP03.041
USB Keyboard, KU0355, Sweden
Ver., 105keys
Chicony
KU0355(silver)
KB.KUP03.042
USB Keyboard, KU0355, UK Ver.,
104keys
Chicony
KU0355(silver)
KB.KUS03.001
USB Keyboard, KU0355, Spanish
Ver., 105keys
Chicony
KU0355(silver)
KB.KUS03.002
USB Keyboard, KU0355, Dutch
Ver., 105keys
Chicony
KU0355(silver)
KB.KUS03.003
USB Keyboard, KU0355, Portugese Chicony
Ver., 105keys
KU0355(silver)
KB.KUS03.004
USB Keyboard, KU0355, US Ver.,
104keys
Appendix B
COMPONENTS
Appendix B
SPEC.
MODEL DESCRIPTION
ACER PART No.
USB Keyboard, KU0355, Canadian/ Chicony
French Ver., 105keys
KU0355(silver)
KB.KUS03.009
USB Keyboard, KU0355, Brazilian
Ver., 107keys
Chicony
KU0355(silver)
KB.KUS03.010
USB Keyboard, KU0355, Swiss
Ver., 105keys
Chicony
KU0355(silver)
KB.KUS03.011
USB Keyboard, KU0355, Belgium
Ver., 105keys
Chicony
KU0355(silver)
KB.KUS03.012
USB Keyboard, KU0355, Holland
Ver., 105keys
Chicony
KU0355(silver)
KB.KUS03.013
USB Keyboard, KU0355, Iceland
Ver., 105keys
Chicony
KU0355(silver)
KB.KUS03.014
USB Keyboard, KU0355,
Norwegian Ver., 105keys
Chicony
KU0355(silver)
KB.KUS03.015
USB Keyboard, KU0355, Hebrew
Ver., 105keys
Chicony
KU0355(silver)
KB.KUS03.016
USB Keyboard, KU0355, Polish
Ver., 105keys
Chicony
KU0355(silver)
KB.KUS03.017
USB Keyboard, KU0355, Slovenian Chicony
Ver., 105keys
KU0355(silver)
KB.KUS03.018
USB Keyboard, KU0355, Slovakian Chicony
Ver., 105keys
KU0355(silver)
KB.KUS03.019
USB Keyboard, KU0355, Turkey
Ver., 105keys
Chicony
KU0355(silver)
KB.KUS03.020
USB Keyboard, KU0355,
RussiamVer., 104keys
Chicony
KU0355(silver)
KB.KUS03.021
USB Keyboard, KU0355, Hungaria Chicony
Ver., 105keys
KU0355(silver)
KB.KUS03.022
USB Keyboard, KU0355, Greek
Ver., 104keys
Chicony
KU0355(silver)
KB.KUS03.023
USB Keyboard, KU0355, Denmark Chicony
Ver., 104keys
KU0355(silver)
KB.KUS03.024
USB Keyboard, KU0355, Czech
Ver., 104keys
Chicony
KU0355(silver)
KB.KUS03.058
USB Keyboard, KU-0355, US Ver.,
104keys, Japan ABS
Chicony
KU0355(silver)
KB.KUS03.062
USB Keyboard, KU-0355, In'l US
Ver., 104keys, Japan ABS
Chicony
KU0355(silver)
KB.KUS03.063
104
COMPONENTS
SPEC.
MODEL DESCRIPTION
ACER PART No.
Chicony
KU0355(silver)
KB.KUS03.064
USB Keyboard, KU-0355, Germany Chicony
Ver., 105keys, Japan ABS
KU0355(silver)
KB.KUS03.065
USB Keyboard, KU-0355, Italian
Ver., 105keys, Japan ABS
Chicony
KU0355(silver)
KB.KUS03.066
USB Keyboard, KU-0355, French
Ver., 105keys, Japan ABS
Chicony
KU0355(silver)
KB.KUS03.067
USB Keyboard, KU-0355, Sweden
Ver., 105keys, Japan ABS
Chicony
KU0355(silver)
KB.KUS03.068
USB Keyboard, KU-0355, UK Ver.,
104keys, Japan ABS
Chicony
KU0355(silver)
KB.KUS03.069
USB Keyboard, KU-0355, Spanish Chicony
Ver., 105keys, Japan ABS
KU0355(silver)
KB.KUS03.070
USB Keyboard, KU-0355, Dutch
Ver., 105keys, Japan ABS
Chicony
KU0355(silver)
KB.KUS03.071
USB Keyboard, KU-0355,
Portugese Ver., 105keys, Japan
ABS
Chicony
KU0355(silver)
KB.KUS03.072
USB Keyboard, KU-0355, Swiss
Ver., 105keys, Japan ABS
Chicony
KU0355(silver)
KB.KUS03.073
USB Keyboard, KU-0355, Belgium Chicony
Ver., 105keys, Japan ABS
KU0355(silver)
KB.KUS03.074
USB Keyboard, KU-0355, Holland
Ver., 105keys, Japan ABS
Chicony
KU0355(silver)
KB.KUS03.075
USB Keyboard, KU-0355, Iceland
Ver., 105keys, Japan ABS
Chicony
KU0355(silver)
KB.KUS03.076
USB Keyboard, KU-0355,
Norwegian Ver., 105keys, Japan
ABS
Chicony
KU0355(silver)
KB.KUS03.077
USB Keyboard, KU-0355, Hebrew
Ver., 105keys, Japan ABS
Chicony
KU0355(silver)
KB.KUS03.078
USB Keyboard, KU-0355, Polish
Ver., 105keys, Japan ABS
Chicony
KU0355(silver)
KB.KUS03.079
USB Keyboard, KU-0355,
Slovenian Ver., 105keys, Japan
ABS
Chicony
KU0355(silver)
KB.KUS03.080
USB Keyboard, KU-0355, Arabic
Ver., 104keys, Japan ABS
105
Appendix B
COMPONENTS
SPEC.
MODEL DESCRIPTION
ACER PART No.
USB Keyboard, KU-0355,
Slovakian Ver., 105keys, Japan
ABS
Chicony
KU0355(silver)
KB.KUS03.081
USB Keyboard, KU-0355, Turkey
Ver., 105keys, Japan ABS
Chicony
KU0355(silver)
KB.KUS03.082
USB Keyboard, KU-0355,
RussiamVer., 104keys, Japan ABS
Chicony
KU0355(silver)
KB.KUS03.083
USB Keyboard, KU-0355, Hungaria Chicony
Ver., 105keys, Japan ABS
KU0355(silver)
KB.KUS03.084
USB Keyboard, KU-0355, Greek
Ver., 104keys, Japan ABS
Chicony
KU0355(silver)
KB.KUS03.085
USB Keyboard, KU-0355, Denmark Chicony
Ver., 104keys, Japan ABS
KU0355(silver)
KB.KUS03.086
USB Keyboard, KU-0355, Czech
Ver., 104keys, Japan ABS
KB.KUS03.087
Chicony
KU0355(silver)
Mouse
KYE
Logitech
PS/2 mouse, 2
button+wheel(black)
NetScroll PS2(black) MS.PSE04.008
USB optical mouse, 2
button+wheel(silver)
PowerScroll
USB(sliver)
MS.PSE04.005
USB optical mouse, 2
button+wheel(silver)
M-UV ACR1(black)
MS.MUV01.00
1
Thyme510(black)
SP.51004.003
Speaker
Neosonica
USB, 3" *2
Monitor
Compal
Appendix B
17" CRT MONITOR,
AC711,TCO99,N.M.,W/EUROPE
POWER CORD
ES.71102.001
17" CRT
MONITOR,AC711,TCO99,N.M.,W/
UK POWER CORD
ES.71102.002
17" CRT
MONITOR,AC711,TCO99,N.M.,W/O
POWER CORD
ES.71102.003
17" CRT
MONITOR,AC711,TCO99,N.M.,W/
US POWER CORD(STK)
ES.71102.004
106
COMPONENTS
107
SPEC.
MODEL DESCRIPTION
ACER PART No.
17" CRT
MONITOR,AC711,MPRII,N.M.,W/
US POWER CORD(AAC)
ES.71102.005
17" CRT
MONITOR,AC711,MPRII,N.M.,W/O
POWER CORD
ES.71102.006
17" CRT
MONITOR,AC711,MPRII,E.M.,W/O
POWER CORD
ES.71102.007
17" CRT
MONITOR,AC711,TCO99,N.M.,W/
EUROPE POWER CORD
ES.71102.001
17" CRT
MONITOR,AC711,MPRII,S.M.,W/O
POWER CORD
ES.71102.008
17" CRT
MONITOR,AC711,MPRII,S.M.W/
AUSTRALIA POWER CORD
ES.71102.009
17" CRT
MONITOR,AC711,MPRII,N.M.,W/
EUROPE POWER CORD
ES.71102.010
17" CRT
MONITOR,AC711,MPRII,N.M.,W/
US POWER CORD(STK)
ES.71102.011
17" CRT
MONITOR,AC711,MPRII,E.M.,W/O
POWER CORD(AAC)
ES.71102.012
17" CRT
MONITOR,AC711,MPRII,N.M.,W/
CHINA POWER CORD
ES.71102.013
15" LCD MONITOR,AL511,W/O
SPEAKER,TCO99,W/EUROPE
POWER CORD
ET.51102.001
15" LCD MONITOR,AL511,W/O
SPEAKER,TCO99,W/UK POWER
CORD
ET.51102.002
15" LCD MONITOR,AL511,W/O
SPEAKER,TCO99,W/O POWER
CORD
ET.51102.004
Appendix B
COMPONENTS
SPEC.
MODEL DESCRIPTION
ACER PART No.
15" LCD MONITOR,AL511,W/O
SPEAKER,TCO99,W/AUSTRALIA
POWER CORD
ET.51102.005
15" LCD MONITOR,AL511,W/O
SPEAKER,TCO99,W/SWISS
POWER CORD
ET.51102.006
15" LCD MONITOR,AL511,W/O
SPEAKER,TCO99,W/CHINA POWER
CORD
ET.51102.007
15" LCD MONITOR,AL511,W/O
SPEAKER,TCO99,W/US POWER
CORD(AAC)
ET.51102.008
15" LCD MONITOR,AL511,W/O
SPEAKER,TCO99,W/US POWER
CORD(STK)
ET.51102.009
Campel
15" LCD MONITOR,AL511(002),W/
O SPEAKER,TCO99,W/US POWER
CORD(STK)
ET.51102.016
Jean
15" LCD MONITOR,AL513,W/O
SPEAKER,TCO99,W/US POWER
CORD(STK)
ET.51305.008
15' LCD MONITOR,AL512,W/
SPEAKER,TCO99,W/US POWER
CORD(STK)
ET.51205.007
17"
CRT,86K,AC707,MPRII,N.M.,W/US
POWER CORD(STK)
ES.70704.011
17" LCD MONITOR, AL702,W/
SPEAKER, TCO99, W/US POWER
CORE (STK)
ET.70204.007
Liteon
Appendix B
108
109
Appendix B
Appendix C
Online Support Information
This section describes online technical support services available to help you repair your Acer Systems.
If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch
office. Acer Branch Offices and Regional Business Units may access our website. However some information
sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
Acer's Website offers you convenient and valuable support resources whenever you need them.
In the Technical Information section you can download information on all of Acer's Notebook, Desktop and
Server models including:
T
Service guides
T
User's manuals
T
Training materials
T
Main manuals
T
Bios updates
T
Software utilities
T
Spare parts lists
T
TABs (Technical Announcement Bulletin)
For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our
technical material.
Also contained on this website are:
T
Detailed information on Acer's International Traveller’s Warranty (ITW)
T
Returned material authorization procedures
T
An overview of all the support services we offer, accompanied by a list of telephone, fax and email
contacts for all your technical queries.
We are always looking for ways to optimize and improve our services, so if you have any suggestions or
comments, please do not hesitate to communicate these to us.
Appendix C
109
110
Veriton 3500/5500/7500
A
ACPI 18
Audio
controller 15
Audio Interface 15
B
BIOS Setup
System Information 20
C
Cache Memory 14
scheme 14
size 14
speed 14
type 14
voltage 14
Chipsets 16
controllers 16
audio 15
serial port 16
video 14
Current 17
D
Device Standby Mode 18
Disk Drives
floppy disk drives A/B 23
E
ECP 16
Environmental Requirements 17
EPP 16
Error Codes 61
Error Sysmptoms List 61
External VGA Port 1
F
fax/data modem 1
Features 1
features 1
connectivity 1
1
design 1
ergonomics 1
Multimedia 1
Performance 1
Frequency 17
front panel 7
FRU 76
G
Global Standby Mode 18
H
Humidity 17
I
IDE Interface 15
Interface
audio 15
Floppy disk drive 15
IDE 15
Video 14
J
Jumper and Connector Information 66
Jumpers 66
K
keyboard 10
M
Machine Disassembly and Replacement 37
Memory
size 14
system 14
Model Definition 93
modem
fax/data 1
MPU-401 15
O
Online Support Information 109
Overview 1
P
2
Parallel Port 16
Password
setting 32
POST 52
Post Check Points 53
POST Error Messages List 52
Power Management 18
Power-On Self-Test (POST) 52
R
Rear Panel 8
RMA 76
S
Serial Port 16
socket
memory 14
Suspend Mode 18
Switching
Power Supply 102W 17
Symptoms List 61
Audio 63
CD/DVD-ROM Drive 62
Diskette Drive 61
Keyboard 65
Memory 61
Modem 63
Monitor 63
Other 65
Parallel Port 65
Power Supply 65
Processor / Processor Fan 61
Real-Time Clock 63
Serial Port 65
System Board 61
Video 63
System Specifications 1
design 1
Features 1
T
Temperature 17
Test Compatible Components 94
Troubleshooting 49
3
U
UART 16
Universal HCI 16
USB Port 16
V
Vibration 17
video
controller 14
Video controller 14
Voltage 17
W
Windows NT 4.0 Environment Test 95
4