Honeywell M7410E Product Data

M7410E
SMALL MODULATING LINEAR
VALVE ACTUATOR
PRODUCT DATA
APPLICATION
100%..0%
0%..100%
0..10V
2..10V
The Honeywell M7410E actuator is specifically designed to
provide modulating control together with the V5822/23,
V5832/33, and V5825B series of small linear valves.
The M7410E is used in fan-coil-units, induction units, small
reheaters and recoolers, and for zone control applications. It
is employed in electronic temperature control systems with
hot and/or cold water as the controlled medium. This actuator
is fully compatible with all controllers providing 0...10 V or
2...10 V output signals.
The 7410E actuator is designed for applications where space
is limited and minimum power consumption is required. A
microprocessor-based, high-performance positioner
guarantees accurate control.
Reliable longtime operation is ensured due to the fact that no
mechanical feedback potentiometer and no mechanical endswitches are needed. Due to an automatic synchronization
function, the close-off point is self-adjusting.
Based on a running time of 150 s, valve positioning and flow
adjustment is very exact. Manual positioning is provided for
all actuators. The actuator is both attractive and robust in
design. A special version with auxiliary switch is available.
FEATURES
·
·
·
·
·
·
·
·
·
·
Microprocessor-based positioner ensures precise
stem positioning
Small size allows installation where space is limited
Low power consumption
Suitable for 0...10 V and 2...10 V controller output
signal (adjustable on site)
Easy-to-operate direct/reverse acting switch
Simple input signal override (e.g. for frost protection
function)
Reliable longtime operation because mechanical
feedback potentiometers and mechanical end
switches are not required
Magnetic coupling for stem force limitation and selfadjustment of the close-of-point
Supplied with pre-wired connection cable
Simple, standardized valve/actuator coupling. No
tools required for mounting
·
·
Visual valve position indicator furnished with
actuator
Manual operation provided by the valve adjustment
cap, extra knob, or with a hexagon key
EN0B-0097GE51 R1004
M7410E SMALL MODULATING LINEAR VALVE ACTUATOR
SPECIFICATIONS
Auxiliary Switches
Motor
Input voltage:
Ratings:
24 Vac ±15%; 50/60 Hz
24...230 Vac, max. 3(1) A
Power consumption: 1.4 VA
Input signal:
modulating 0...10 V, 2...10 V
(adjustable); <0.1 mA
Operation:
direct/reverse (adjustable)
Switch position
(factory supplied):
Stroke:
6.5 mm
Running time:
150 s at 50 Hz
120 s at 60 Hz
Stem force:
depending on type (see table)
180 N (for valves DN 15..20)
300 N (for valves DN 25..40 and
V5825B)
Insulation class:
III in accordance with EN 60730
Connection cable:
1.5 m
Ambient operating
temperature limits:
0...55 °C
0.4 kg
Suitable valves:
see table
Manual operation:
see table
Switch S1 (fix)
17.8 ± 0.2 mm
Switch S2 (adjust.)
11.7 ± 0.2 mm
OPERATION
The movement of the electric actuator is produced by a screw
spindle which is driven in both directions by a synchronous
motor through a set of gears. A magnetic clutch limits the
torque of the gear assembly and the driving force of the
actuator. The actuator is fixed to the valve body by means of
a coupling ring requiring no tools for mounting. The actuator
is maintenance-free and supplied completely with a ready-towire connecting cable.
A microprocessor-based high performance positioner
guarantees accurate control. The close-off position is selfadjusting by means of an automatic synchronization function.
Synchronization is performed when the applied control signal
is 0 V or 10 V. The actuator then drives every minute for 5
seconds into the end position in order to ensure close-off
even after manual operation.
Protection standard: IP 42 in accordance with EN 60529
Weight:
5...24 V max. 100 mA
VERSIONS
Manual operation
Stem
force
Aux.
switch S1
Aux.
switch S2
Housing
type
OS number
Provided by the valve
adjustment cap
180 N
300 N
–
–
–
–
B
B
M7410E1002
M7410E1028
With manual
operation
Integrated
"
180 N
300 N
–
–
–
–
C
C
M7410E2026
M7410E2034
With manual
operation and
auxiliary switches
Integrated
"
180 N
300 N
x
x
x
x
C
C
M7410E4022
M7410E4030
Standard
Special versions
EN0B-0097GE51 R1004
Special cable length
length = 3 m / 5 m / 10 m
upon request
2
M7410E SMALL MODULATING LINEAR VALVE ACTUATOR
MOUNTING POSITION
SWITCH SELECTION
The actuator may only be mounted beside or above the
valve. Adjust the valve in the correct position before
mounting the actuator.
The built-in selector switches must be set according to the
valve type (2-way or 3-way), valve size, and the controller
output signal (0...10 V or 2...10 V), see Fig. 4.
closes
Y=+10V=
A
B
factory
setting
opens
Y=+10V=
100%...0%
Y = 0...+10V
A
B
0%...100%
0...10V
2...10V
factory
setting
opens
Y=+10V=
Y = 2...+10V
A
Fig. 1. Mounting positions
AB
B
MOUNTING
Fig. 4. Selecting valve type and output signal
Before the actuator is fixed to the valve, the adjustment cap
must be removed (Fig. 2). Make sure that the actuator is in
the open position (factory-supplied position) before fixing the
actuator to the valve body.
ELECTRIC WIRING
The electrical installation must comply with Fig. 5.
INPUT SIGNAL OVERRIDE
To override the controller output signal, the input signal must
be connected to COM (0 %) or 24 V (100 %) using an
external switch (see Fig. 5).
Fig. 2. Remove protection cap
The actuator must be mounted by hand. Do not use tools or
additional force insofar as this may damage the actuator and
valve.
Fig. 5. Connection of input switch
Fig. 3. Mounting the actuator
3
EN0B-0097GE51 R1004
M7410E SMALL MODULATING LINEAR VALVE ACTUATOR
MANUAL OPERATION
Actuators with the OS-number M7410E2... and M7410E4...
feature a hexagonal key hole for manual operation. For more
comfort, an additional knob for manual adjustment is packed
separately. To prevent valve damage, operation is permitted
only when there is no power applied to the motor.
a
b
c
a
b
c
Fig. 8. Auxiliary switch cables
4 mm
Adjustment of Auxiliary Switch 2
The auxiliary switch should be adjusted by a skilled person,
only. Move the actuator to the position where the switch is to
be operated. Cut the plastic skin with a sharp knife. The
adjustment screw can be accessed below the skin. Turn the
screw clockwise until the end stop is reached. Turn the screw
counterclockwise until the switch point is achieved. To check
that the required position has been set, move the actuator.
Finally, seal the adjustment hole with a piece of tape.
Fig. 6. Manual operation
COMMISSIONING ADVICE
A functional check of the valve actuator can be carried out by
changing the Y input signal. The movement of the actuator
stem (Fig. 7) indicates whether the valve is opening or
closing. If the direction of travel is not correct, the
direct/reverse-switch must be reset.
Fig. 9. Adjustment of auxiliary switch S2
17.8 mm
11.7 mm
Fig. 7. Movement of the actuator stem
AUXILIARY SWITCHES
The actuators with the OS-number M7410E4022 and
M7410E4033 feature 2 auxiliary switches. Each switch has
its own cable. Auxiliary switch S1 with fixed switchpoint when
the stem position is in. Auxiliary switch S2 with adjustable
switchpoint when the stem position is out.
EN0B-0097GE51 R1004
4
M7410E SMALL MODULATING LINEAR VALVE ACTUATOR
Electric Wiring of Auxiliary Switches
Application Example:
Switching Off an Electrical Appliance
The electrical installation must comply with the wiring
diagram shown in Fig. 10. If the auxiliary switch is connected
to 230 Vac, a switch with a contact gap of at least 3 mm for
each pole must be fitted with the installation.
2-Way-Valve
DN 15, DN 20
24 Vac:
max. 100 mA
230 Vac:
max. 5 (1)A
(230 Vac only):
M7410E
E. g. fan, pump etc.
BLUE
max. 5 (1)A
BLACK
Fig. 11. Electric wiring of auxiliary switch
open
DN 15,
DN 20
A
B
A
B
A
A
B
A
B
A
close
DN 15 DN 40
A
AB
A
AB
A
max. 5 (1)A
open
AB
A
AB
A
AB
B
B
BROWN
BROWN
BROWN
BLACK
BLUE
BLACK
BLACK
BLUE
BROWN
BLUE
BLACK
BLACK
Fig. 12. Electric wiring of auxiliary switch
B
BROWN
BLUE
BLUE
B
close
BLUE
DN 25 - DN 40
E. g. fan, pump etc.
AB
B
A
DN 15 - DN 20
B
open
B
DN 15 DN 20
DN 15 - DN 40
B
open
close
DN 25 DN 40
All Other Valves
close
BLACK
BROWN
BLUE
BLACK
Fig. 10. Electric wiring of auxiliary switch
5
EN0B-0097GE51 R1004
M7410E SMALL MODULATING LINEAR VALVE ACTUATOR
DIMENSIONS (MM)
82
58
100
109
49
60
49
87
Fig. 13. Housing type B
Fig. 14. Housing type C
Automation and Control Solutions
Honeywell GmbH
Böblinger Straße 17
D-71101 Schönaich
Phone: (49) 7031 63701
Fax: (49) 7031 637493
http://europe.hbc.honeywell.com
Subject to change without notice. Printed in Germany
EN0B-0097GE51 R1004
Manufacturing location certified to