Sharp AR-5316 Specifications

[00]COVER.fm 1 ページ
2005年7月1日 金曜日 午後5時36分
CODE : 00ZAR5316/A1E
DIGITAL COPIER
MODEL
AR-5316
(For North America)
AR-5316
(With optional AR-SP6 installed)
CONTENTS
[ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
[ 2 ] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
[ 3 ] CONSUMABLE PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
[ 4 ] EXTERNAL VIEWS AND INTERNAL STRUCTURES . . . . . . . . . . . . . . .4-1
[ 5 ] UNPACKING AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
[ 6 ] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
[ 7 ] SIMULATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
[ 8 ] USER PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1
[ 9 ] TROUBLE CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
[10] MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-1
[11] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-1
[12] FLASH ROM VERSION UP PROCEDURE . . . . . . . . . . . . . . . . . . . . . .12-1
[13] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-1
Parts marked with “ “ are important for maintaining the safety of the set.
Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
[co]CONTENTS.fm
1 ページ 2005年7月1日 金曜日 午後5時33分
CONTENTS
[1] GENERAL
1. Note for servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[2] SPECIFICATIONS
1. Copy mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
[3] CONSUMABLE PARTS
1. Supply system table . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES
1. Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
2. Internal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
3. Operation Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
4. Motor, solenoid, clutch . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
[5] UNPACKING AND INSTALLATION
5. Changing the copy paper size in the tray . . . . . . . . . . . 5-1
[10] MAINTENANCE
1. Maintenance table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
2. Maintenance display system . . . . . . . . . . . . . . . . . . . . . 10-1
3. Note for replacement of consumable parts . . . . . . . . . . 10-1
[11] DISASSEMBLY AND ASSEMBLY
1. High voltage section . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
2. Optical section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2
3. Fusing section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4
4. Paper exit section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6
5. MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-8
6. Optical frame unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-8
7. LSU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-9
8. Tray paper feed section / Paper transport section . . . . . 11-9
9. Manual multi paper feed section . . . . . . . . . . . . . . . . . . 11-11
[6] ADJUSTMENTS
1. Adjustment item list . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
2. Copier adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
[7] SIMULATIONS
1. Entering the simulation mode. . . . . . . . . . . . . . . . . . . . 7-1
2. Canceling the simulation mode . . . . . . . . . . . . . . . . . . 7-1
3. List of simulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
4. Contents of simulations . . . . . . . . . . . . . . . . . . . . . . . . 7-2
[8] USER PROGRAMS
1. List of user programs . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
[9] TROUBLE CODE LIST
1. Trouble code list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
2. Details of trouble codes . . . . . . . . . . . . . . . . . . . . . . . . 9-1
10. Power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13
11. Developing section . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14
12. Process section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-15
13. Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-15
[12] FLASH ROM VERSION UP PROCEDURE
1. Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
2. Download procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
3. Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2
[13] ELECTRICAL SECTION
1. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
3. Actual wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2
[01]GENERAL.fm
1 ページ 2005年7月1日 金曜日 午後5時25分
[1] GENERAL
•poorly ventilated
1. Note for servicing
Pictogram
The label (
) in the fusing area of the machine indicates the
following:
: Caution, risk of danger
: Caution, hot surface
A. Warning for servicing
•The fusing area is hot. Exercise care in this area when removing misfed
paper.
•Do not look directly at the light source. Doing so may damage your eyes.
•exposed to direct sunlight
B. Cautions for servicing
•Do not switch the machine rapidly on and off. After turning the machine
off, wait 10 to 15 seconds before turning it back on.
•Machine power must be turned off before installing any supplies.
•Place the machine on a firm, level surface.
•Do not install the machine in a humid or dusty location.
•When the machine is not used for a long time, for example, during
prolonged holidays, turn the power switch off and remove the power
cord from the outlet.
•When moving the machine, be sure to turn the power switch off and
remove the power cord from the outlet.
•Do not cover the machine with a dust cover, cloth or plastic film while the
power is on. Doing so may prevent heat dissipation, damaging the
machine.
•Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous laser radiation
exposure.
•The socket-outlet shall be installed near the machine and should be
easily accessible.
•subject to extreme temperature or humidity changes, e.g., near an air
conditioner or heater.
C. Note for installation place
Improper installation may damage the machine. Please note the
following during initial installation and whenever the machine is moved.
Caution : If the machine is moved from a cool place to a warm place,
condensation may form inside the machine. Operation in this
condition will cause poor copy quality and malfunctions. Leave
the machine at room temperature for at least 2 hours before
use.
Do not install your machine in areas that are:
•damp, humid, or very dusty
The machine should be installed near an accessible power outlet for
easy connection and disconnection.
Be sure to connect the power cord only to a power outlet that meets the
specified voltage and current requirements. Also make certain the outlet
is properly grounded.
Note : Connect the machine to a power outlet which is not used for other
electric appliances. If a lighting fixture is connected to the same
outlet, the light may flicker.
Be sure to allow the required space around the machine for servicing
and proper ventilation.
8" (20 cm)
8"
(20 cm)
AR-5316 GENERAL 1-1
8"
(20 cm)
[02_03]SPEC_CONSUMABLE.fm 1 ページ 2005年7月1日 金曜日 午後5時26分
[2] SPECIFICATIONS
The table below shows the specifications of this model and the contents of changes from the AR-M160/M205 and AR-5316.
Item
AR-M160
1cassette +
Multi manual paper feed
Approx.31.3Kg
Paper feed system
Weight
Interface
USB1.1/USB2.0
IEEE1284
AR-5316
One automatic feeding paper tray(250sheets) +
bypass tray(100sheets)
Approx.31.3Kg
(Not including TD cartridge)
IEEE1284parallel connector/USB1.1
Option
Machine
250 sheets paper feed unit
Model
AR-D24 / D25
AR-M160
AR-5316
O
-
SPF
AR-SP6
O
O
Original cover
AR-VR5
Standard
Standard
Remark
O : The option can be installed.
- : The option cannot be installed.
[3] CONSUMABLE PARTS
1. Supply system table
NO
1
2
Name
TD cartridge(Black)
Drum cartridge
Content
Life
Toner developer cartridge
(Toner: Net Weight 300g)
(Developer: Net Weight 400g)
IC chip
Polyethylene bag
x1
Drum cartridge
x1
Product name
9K
AR-016TD
30K
AR-016DR
x1
x1
Packed items:DR cartridge(30K)/TD cartridge(4.5K)
Note 1: The individual carton is printed with English, German, French, and Spanish as well as the green mark.
AR-5316 SPECIFICATIONS 2-1
Remark
*Life setting by LT 5% document
[04]EXTERNALVIEWS.fm 1 ページ
2005年7月1日 金曜日 午後5時26分
[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES
1. Appearance
1
2
7
6
2
16
3
4
17
4
10
5
8
11
15
9
1
Glass cleaner
2
4
7
10
13
16
Handles
Paper output tray
Side cover
Bypass tray
USB 1.1 connector
5
8
11
14
17
Document feeder cover (when the SPF
is installed) /document cover
Power switch
Front cover
Side cover handle
Bypass tray extension
Parallel connector
12
14
13
3
Document glass
6
9
12
15
Operation panel
Paper trays
Bypass tray guides
Charger cleaner
2. Internal
25
18 19
24
20
23
22
21
29
26
28
18
21
24
27
30
Document feeder tray
(when the SPF is installed)
Right side cover
(when the SPF is installed)
TD cartridge strap
Fusing unit release levers
Fusing unit paper guide
19
22
25
28
30
27
Original guides
(when the SPF is installed)
Exit area
(when the SPF is installed)
TD cartridge lock release lever
Drum cartridge
20
23
Feeding roller cover
(when the SPF is installed)
TD cartridge
26
29
Roller rotating knob
Drum cartridge handle
AR-5316 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-1
[04]EXTERNALVIEWS.fm 2 ページ
2005年7月1日 金曜日 午後5時26分
3. Operation Section
1
2
3
XYZOOM
ON LINE
DUAL
PAGE
COPY
1
4
7
ON LINE key/indicator
SPF indicator
(when the SPF is installed)
PAPER SIZE indicators
9
2
5
8
DUAL PAGE COPY key/indicator
Paper feed location / misfeed location
indicators
PRESET RATIO selector keys /
indicators
11
10
AUDIT CLEAR
AUTO
TEXT
PHOTO
12
POWER SAVE
ORIGINAL PAPER
SIZE
SIZE
11X17
8½X14
8½X11
8½X5½
8½X11
EXTRA
TRAY
AUTO
SELECT IMAGE
ORIGINAL SIZE
ENTER
6
XY-ZOOM key/indicator
ORIGINAL SIZE ENTER key /
ORIGINAL SIZE indicators
15
16
17
ZOOM
25 400%
INTERRUPT
CLEAR
200%
141
129
121
100%
95
77
64
50%
1 3 5
18
14
13
3
6
7 19 4 20
21
CLEAR ALL
START
PRESET RATIO
5
8
23
22
24
25 26
Not used for this machine.
9
12
15
18
21
24
AUTO/TEXT/PHOTO key / indicators
POWER SAVE indicator
ZOOM indicator
Light and Dark keys / indicators
AUTO IMAGE key / indicator
START key / indicator
10
13
16
19
22
25
AUDIT CLEAR key
Display
Zoom keys
PAPER SIZE ENTER key
Numeric keys
CLEAR ALL key
11
14
17
20
23
26
Alarm indicators
Copy ratio display key
INTERRUPT key / indicator
TRAY SELECT key
# key
CLEAR key
AR-5316 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-2
[05]UNPACKING.fm 1 ページ 2005年7月1日 金曜日 午後5時26分
[5]UNPACKING AND INSTALLATION
5. Changing a tray's paper size setting
3) Squeeze the lock lever of the front guide and slide the front guide to
match the width of the paper, and move the left guide to the
appropriate slot as marked on the tray.
Follow these steps to change a tray's paper size setting.
Left guide
Note:
•The paper size setting cannot be changed when the machine has
stopped temporarily due to running out of paper or a misfeed, or during
interrupt copying.
•During printing (even in copy mode), the paper size setting cannot be
changed.
•Do not load paper that is a different size than the paper size setting.
Copying will not be possible.
1) Hold down the [PAPER SIZE ENTER] key for more than 5 seconds to
set the selected paper size.
The currently selected paper feed location indicator will blink and the
corresponding paper size (which is currently set) indicator will light
steadily.
All other indicators will go out.
Front guide
•The front guide is a slide-type guide. Grasp the locking knob on the
guide and slide the guide to the indicator line of the paper to be loaded.
•The left guide is an insert-type guide. Remove it and then insert it at the
indicator line of the paper to be loaded.
•When using 11" x 17" sized paper store the left guide in the slot at the
left front of the paper tray.
GINAL
PAPER
SIZE
11X17
8½X14
8½X11
8½X5½
8½X11
EXTRA
2) Use the [ORIGINAL SIZE ENTER] key to select the paper size.
The indicator of the selected paper size lights up.
GINAL
PAPER
SIZE
11X17
ORIGINAL SIZE 8½X14
ENTER
8½X11
8½X5½
8½X11
EXTRA
4) Press the [START] key and then the [PAPER SIZE ENTER] key.
To change the paper size setting of another tray, repeat steps 2) to 4)
after pressing the [START] key.
START
Note: Affix the paper size label for the paper size selected in step 2) to
the label position on the right end of the tray.
Important points when using the printer mode
•Make sure that the tray's paper size setting is the same as the tray's
paper size setting in the printer driver. For example, if the tray's paper
size setting is 8-1/2”x11R, set "Setting Paper Size" to "Letter R". For
more information, see "CONFIGURING THE PRINTER DRIVER" in the
"Software Setup Guide".
AR-5316 UNPACKING AND INSTALLATION 5-1
[06]ADJUSTMENT.fm 1 ページ
2005年7月1日 金曜日 午後5時27分
[6]ADJUSTMENTS
1.Adjustment item list
Section
A
B
Process
section
Mechanism
section
Adjustment item
Adjustment procedure/SIM No.
(1)
Developing doctor gap adjustment
Developing doctor gap adjustment
(2)
MG roller main pole position adjustment
MG roller main pole position adjustment
(3)
Developing bias voltage check
(4)
Main charger voltage check
(1)
Image position adjustment
SIM-50
(2)
Main scanning direction (FR direction) distortion balance
adjustment
No. 2/3 mirror base unit installing position adjustment
(3)
Main scanning direction (FR direction) distortion adjustment
Rail height adjustment
(4)
Sub scanning direction (scanning direction) distortion
adjustment
Winding pulley position adjustment
(5)
Main scanning direction (FR direction) magnification ratio
adjustment
SIM 48-1
(6)
Sub scanning direction (scanning direction) magnification ratio OC mode in copying (SIM 48-1)
adjustment
SPF mode in copying (SIM 48-5)
(7)
Off center adjustment
Copy lamp unit installing position adjustment
OC mode (SIM 50-12)
SPF mode (SIM 50-12)
C
Image density
adjustment
(8)
SPF white correction pixel position adjustment
(required in an SPF model when replacing the lens unit)
SIM63-7
(1)
Copy mode
SIM 46-1
2.Copier adjustment
A.Process section
(2) MG roller main pole position adjustment
(1) Developing doctor gap adjustment
1) Remove and separate the waste toner box and put the developing
unit on a flat surface.
2) Tie a string to a needle or a pin.
3) Hold the string and bring the needle close to the MG roller
horizontally. (Do not use paper clip, which is too heavy to make a
correct adjustment.) (Put the developing unit horizontally for this
adjustment.)
4) Do not bring the needle into contact with the MG roller, but bring it to
a position 2 or 3mm apart from the MG roller. Mark the point on the
MG roller which is on the extension line from the needle tip.
5) Measure the distance from the marking position to the top of the
doctor plate of the developing unit to insure that it is 18mm.
If the distance is not within the specified range, loosen the fixing
screw A of the main pole adjustment plate, and move the adjustment
plate in the arrow direction to adjust.
1) Loosen the developing doctor fixing screw A.
2) Insert a thickness gauge of 1.5mm to the three positions at 20mm
and 130mm from the both ends of the developing doctor as shown.
3) Push the developing doctor in the arrow direction, and tighten
developing doctor fixing screw. (Perform the same procedure for
front and the rear frames.)
4) Check the clearance of the developing doctor. If it is within
specified range, then fix the doctor fixing screw with screw lock.
* When inserting a thickness gauge, be careful not to scratch
developing doctor and the MG roller.
the
the
the
the
<Adjustment specification>
Developing doctor gap
Both ends (20mm from the both ends) : 1.5 +0.1
- 0.15 mm
C (Center) (150mm from the both ends) :1.55 +0.15
- 0.2 mm
AR-5316 ADJUSTMENT 6-1
[06]ADJUSTMENT.fm 2 ページ
2005年7月1日 金曜日 午後5時27分
(3)Developing bias voltage check
B.Mechanism section
Note: Use a digital multi-meter with an internal resistance of 10MΩ or
more.
Note: If a jam error or paper empty occurs during copying in the
adjustment by the simulation, the image data are not saved, and
therefore recopying is required.
1) Set the digital multi-meter range to DC700V.
2) Put the test rod of the digital multi-meter on the developing bias
voltage output check pin.
3) Turn on the power, execute SIM25-1.
(1)Image position adjustment
a.OC image lead edge position adjustment (SIM 50-1)
Note: In advance to this adjustment, the sub scanning magnification ratio
adjustment must be performed.
1) Set a scale on the OC table as shown below.
<Specification>
Mode
Specification
Developing bias voltage
DC - 400±8V
(4) Grid bias voltage check
Note: Use a digital multi-meter with an internal resistance of 10MΩ or
more.
2) Make a copy.
3) Check the copy output. If necessary, perform the following
adjustment procedures.
4) Execute SIM 50-1.
5) Set the OC lead edge position set value (Exposure display
<<PHOTO>> ON) to [1]
The OC image scanning start position is shifted inside the document
edge.
6) Set the main cassette lead edge void adjustment value (Exposure
display <<TEXT>> ON) * to [1]
The lead edge void becomes the minimum.
7) Set the main cassette print start position value (Exposure display
<<AUTO+MAIN CASSETTE LAMP>> ON) to [1] and make a copy.
The print start position is shifted inside the document edge.
5mm
1) Set the digital multi-meter range to DC700V.
2) Put the test rod of the digital multi-meter on the grid bias voltage
output check pin.
3) Turn on the power.
(The voltage is outputted in the grid bias High output mode during
warming up, and in the grid bias Low output mode when warming up
is completed.)
5
4mm
10
*The dimension varies depending on the model.
8) Measure the image loss R of the copied image. Enter the set value of
the image scanning lead edge position (Exposure display
<<PHOTO>> ON) again.
•1 step of the set value corresponds to about 0.1mm shift.
•Calculate the set value from the formula below.
R/0.1(mm) = Image loss set value
<R: Image loss measurement value (mm)>
5mm
0mm
5
10
* The scanning edge is set.
(A line may be printed by scanning the document edge.)
<Specification>
Mode
Specification
Grid bias LOW
DC - 400±8V
Grid bias HIGH
DC - 525±10V
Example:
4/0.1 = 40 = about 40
Note: If the set value is not obtained from the above formula, perform the
fine adjustment.
AR-5316 ADJUSTMENT 6-2
[06]ADJUSTMENT.fm 3 ページ
2005年7月1日 金曜日 午後5時27分
9) Measure the distance H between the paper lead edge and the image
print start position. Set the image print start position set value
(Exposure display <<AUTO+MAIN CASSETTE LAMP>> ON) again.
•1 step of the set value corresponds to about 0.1mm shift.
•Calculate the set value from the formula below.
H/0.1(mm) = Image print start position set value
<H: Print start position measurement value (mm)>
b.SPF image lead edge position adjustment (SIM50-6)
1) Set a scale on the OC table as shown below.
0mm
0mm
5
10
Note: Since the printed copy is used as a test chart, put the scale in
paralled with the edge lines.
*Fit the print edge with the paper edge, and perform the
lead edge adjustment.
Example:
5/0.1 = 50 = about 50
Note: If the set value is not obtained from the above formula, perform the
fine adjustment.
10) Set the lead edge void adjustment value (Exposure display
<<TEXT>> ON)* again.
•1 step of the set value corresponds to about 0.1mm shift.
•Calculate the set value from the formula below.
B/0.05 (mm) = Lead edge void adjustment value
<B: Lead edge void (mm)>
2) Make a copy, Then use the copy output as an original to make an
SPF copy again.
3) Check the copy output. If necessary, perform the following
adjustment procedures.
4) Execute SIM 50-6.
5) Set the SPF lead edge position set value (Exposure display
<<AUTO>> ON) so that the same image is obtained as that obtained
in the previous OC image lead edge position adjustment.
<Adjustment specification>
Adjustment mode
SPF image lead
edge position
(1st print surface)
2.5mm
5
SIM
SIM
50-6
LED
AUTO
Set value
Spec value
1 step:
Lead edge
0.1mm shift void:
1 - 4mm
2.5mm
Image loss:
3mm or
less
10
Example:
When setting the lead edge void to 2.5mm
:2.5 /0.05 = about 50
Note: If the set value is not obtained from the above formula, perform the
fine adjustment.
* Multi bypass tray lead edge void adjustment: Exposure display
<<TEXT + PHOTO>>
<Adjustment specification>
Adjustment
mode
SIM
LED
Set
value
Spec
value
Set
range
OC image lead
edge position
SIM
50-1
PHOTO
R/0.1
Lead edge
Main cassette
print start
position
AUTO
+
MAIN
B/0.1
void:
1 - 4mm
Multi bypass
tray print start
position
AUTO
+
MULTI
Lead edge void
TEXT
1 ~ 99
Image loss:
3mm or
less
B/0.05
AR-5316 ADJUSTMENT 6-3
Set
range
1 ~ 99
[06]ADJUSTMENT.fm 4 ページ
2005年7月1日 金曜日 午後5時27分
c.Rear edge void adjustment (SIM50-1, SIM50-19)
e.Side edge void area adjustment (SIM26-43)
1) Set a scale as shown in the figure below.
Note: Before performing this adjustment, be sure to check that the paper
off center adjustment (SIM 50-10) is completed.
A4(8.5" x 11")
Paper rear edge
2) Set the document size to A4 (8.5" x 11"), and make a copy at 100%.
3) If necessary, perform the following adjustment procedure.
1) Set a test chart (UKOG-0089CSZZ) on the document table.
2) Select a paper feed port and make two copies. Compare the 2nd
copy and the test chart. If necessary, perform the following
adjustment procedure.
* The 1st copy does not show the void. Be sure to check the 2nd copy.
3) Execute SIM 26-43 and set the density mode to AUTO(right edge
void) + TEXT (Left edge void).
The currently set adjustment value is displayed.
4) Enter the set value and press the start key. The correction value is
stored.
<Adjustment specification>
Void amount (Standard value: 4mm or less)
ode
SIM
Left edge void
Scale image
SIM
26-43
Paper rear edge
4) Execute SIM 50-1 and set the density mode to AUTO + TEXT +
PHOTO (Rear edge void).The currently set adjustment value is
displayed.
5) Enter the set value and press the start key. The correction value is
stored and a copy is made.
<Adjustment specification>
Mode
SIM
LED
Rear edge void
SIM
50-1
AUTO
+
TEXT
+
PHOTO
*
LED
Set value
AUTO
1 step:
0.5 ~ 4mm 1 ~ 99
(right
0.5mm shift
edge)
+
TEXT
(left edge)
(2) Main scanning direction(FR direction) distortion balance
adjustment
1) Remove the OC glass and the right cabinet.
Set value
Specification
1 step:
4mm or
0.1mm shift less
Set
range
(1)
1 ~ 99
(1)
(2)
(3)
(4)
(3)
1) Set a test chart (UKOG-0089CSZZ) on the document table.
2) Select a paper feed port and make a copy. Compare the copy and
the test chart. If necessary, perform the following adjustment
procedure.
3) Execute SIM 50-10. After completion of warm-up, shading is
performed and the currently set off center adjustment value of each
paper feed port is displayed.
4) Enter the set value and press the start key. The correction value is
stored and a copy is made.
<Adjustment specification>
SIM
Paper off
center
SIM
50-10
LED
Set value
Specification
Single:
AUTO Add 1:
+
0.1mm shift Center
Selected to R side. ±2.0mm
tray ON
Reduce 1:
0.1mm shift
to L side.
Set
range
The void adjustment values on the right and the left must be the
same.
d. Paper off center adjustment (SIM50-10)
Mode
Specification
Set
range
1 ~ 99
AR-5316 ADJUSTMENT 6-4
[06]ADJUSTMENT.fm 5 ページ
2005年7月1日 金曜日 午後5時27分
4) Loosen the set screw of the scanner drive pulley which is not in
contact with No. 2/3 mirror base unit positioning plate.
5) Without moving the scanner drive pulley shaft, manually turn the
scanner drive pulley until the positioning plate is brought into contact
with No. 2/3 mirror base unit, then fix the scanner drive pulley.
2) Loosen the copy lamp unit wire fixing screw.
Wire fixing screw
3) Manually turn the mirror base drive pulley and bring No. 2/3 mirror
base unit into contact with the positioning plate. At that time, if the
front frame side and the rear frame side of No. 2/3 mirror base unit
are brought into contact with the positioning plate at the same time,
the mirror base unit parallelism is proper. If one of them is in contact
with the positioning plate, perform the adjustment of 4).
6) Put No. 2/3 mirror base unit on the positioning plate again, push the
projections on the front frame side and the rear frame side of the
copy lamp unit to the corner frame, and tighten the wire fixing screw.
AR-5316 ADJUSTMENT 6-5
[06]ADJUSTMENT.fm 6 ページ
2005年7月1日 金曜日 午後5時27分
(3)Main scanning direction (FR direction) distortion
adjustment
4) Loosen the mirror base drive pulley fixing screw on the front frame
side or on the rear frame side.
This adjustment must be performed in the following cases:
•When the mirror base drive wire is replaced.
•When the lamp unit, or No. 2/3 mirror holder is replaced.
•When a copy as shown is made.
When La < Lb
Turn the mirror base drive pulley on the front frame side in the
arrow direction A.
(Do not move the mirror base drive pulley shaft.)
When La > Lb
Turn the mirror base drive pulley on the front frame side in the
arrow direction A.
(Do not move the mirror base drive pulley shaft.)
Lb
La
Rear side
Paper exit
direction
A
Copy
Original
B
1) Set A3 (11" x 17") white paper on the original table as shown below.
Front side
Allow a little space.
5)Tighten the mirror base drive pulley fixing screw.
<Adjustment specification>
La = Lb
Glass holding plate
A3 (11" x 17") white paper
Fit the paper edge and
the glass holding plate edge.
2) Open the original cover and make a normal (100%) copy.
3) Measure the width of the black background at the lead edge and at
the rear edge.
6) Execute the main scanning direction (FR) distartion balance
adjustment previously described in 2) again.
(4) Sub scanning direction (scanning direction) distortion
adjustment
When there is no skew copy in the mirror base scanning direction and
there is no horizontal error (right angle to the scanning direction), the
adjustment can be made by adjusting the No. 2/3 mirror base unit rail
height.
Before performing this adjustment, be sure to perform the horizontal
image distortion adjustment in the laser scanner section.
This adjustment must be performed in the following cases:
•When the mirror base wire is replaced.
•When the copy lamp unit or No. 2/3 mirror unit is replaced.
•When the mirror unit rail is replaced or moved.
•When a following copy is made.
Paper exit direction
La: Lead edge black background width
Lb: Rear edge black background width
Original
If the width (La) of the black background at the lead edge is equal that
(Lb) at the rear edge, there is no need to execute the following
procedures of 4) ~ 7).
AR-5316 ADJUSTMENT 6-6
Copy A
Copy B
[06]ADJUSTMENT.fm 7 ページ
2005年7月1日 金曜日 午後5時27分
1) Making of a test sheet
Make test sheet by drawing parallel lines at 10mm from the both
ends of A3 (11" x 17") white paper as shown below. (These lines
must be correctly parallel to each other.)
When La < Lb
Shift the mirror base B rail downward by the half of the
difference of Lb - La.
Example: When La = 12mm and Lb = 9mm, shift the mirror
base B rail upward by 1.5mm.
Parallel line
Parallel line
10mm
When La > Lb
Shift the mirror base B rail upward by the half of the
difference of La - Lb.
10mm
When Lc > Ld
Shift the mirror base B rail downward by the half of the
difference of Lc - Ld.
10mm
When Lc < Ld
Shift the mirror base B rail downward by the half of the
difference of Ld - Lc.
10mm
White paper
2) Make a normal (100%) copy of the test sheet on A3 (11" x 17")
paper. (Fit the paper edge with the glass holding plate edge.)
3) Measure the distances (La, Lb, Lc, Ld) at the four corners as shown
below.
When moving the mirror base rail, hold the mirror base rail
with your hand.
<Adjustment specification>
La = Lb, Lc = Ld
La
Lc
5) After completion of adjustment, manually turn the mirror base drive
pulley, scan the mirror base A and mirror base B fully, and check that
the mirror bases are not in contact with each other.
* If the mirror base rail is moved extremely, the mirror base may be in
contact with the frame or the original glass. Be careful to avoid this.
Paper exit
direction
(5) Main scanning direction (FR direction) magnification
ratio adjustment (SIM 48-1)
Lb
Ld
When La = Lb and Lc = Ld, no need to perform the procedures 4) and 5).
Note: Before performing this adjustment, be sure to check that the CCD
unit is properly installed.
1) Put a scale on the original table as shown below.
4) Move the mirror base F rail position up and down (in the arrow
direction) to adjust.
2) Execute SIM 48-1.
3) After warm-up, shading is performed and the current set value of the
main scanning direction magnification ratio is displayed on the
display section in 2 digits.
4) Select the mode and press the start key again.
5) Manual correction mode (TEXT lamp ON)
Enter the set value and press the start key.
The set value is stored and a copy is made.
Note: If the rear side rail is used for the adjustment, the scanning position
of the white balance sheet is shifted and "E7-04" may occur only
when scanning with the SPF. Therefore it is advisable to use the
front side rail for the adjustment.
AR-5316 ADJUSTMENT 6-7
[06]ADJUSTMENT.fm 8 ページ
2005年7月1日 金曜日 午後5時27分
<Adjustment specification>
Note: A judgment must be made with 200mm width, and must not be
made with 100mm width.
Mode
Main scanning
direction
magnification
ratio
Specification
At normal:
±1.0%
SIM
Set value
SIM 48-1 Add 1:0.1%
increase
Reduce 1:
0.1%
decrease
Set range
1 ~ 99
(6) Sub scanning direction (scanning direction)
magnification ratio adjustment (SIM 48-1, SIM 48-5)
Note: Since the printed copy is used as a test chart, put the scale in
parallel with the edge lines.
2) Set the test chart on the SPF and make a normal (100%) copy.
3) Compare the scale image and the actual image. If necessary,
perform the following adjustment procedures.
4) Execute SIM 48-5.
5) After warm-up, shading is performed.
The auto density lamp lights up and the current front surface sub
scanning direction magnification ratio correction value is displayed in
two digits on the display section.
6) Enter the set value and press the start key.
The set value is stored and a copy is made.
<Adjustment specification>
a. OC mode in copying (SIM48-1)
Note: Before performing this adjustment, be sure to check that the CCD
unit is properly installed.
1) Put a scale on the original table as shown below, and make a normal
(100%) copy.
2) Compare the scale image and the actual image. If necessary,
perform the following adjustment procedures.
3) Execute SIM 48-1.<<PHOTO>>
4) After warm-up, shading is performed and the current set value of the
main scanning direction magnification ratio is displayed on the
display section in 2 digits.
5) When the photo lamp is lighted by pressing the density selection key,
the current magnification ratio correction value in the sub scanning
direction is displayed in lower 2 digits of the display section.
6) Enter the set value and press the start key.
The set value is stored and a copy is made.
Mode
Sub scanning
direction
magnification
ratio
(SPF mode)
Specification
Normal
±1.0%
SIM
Set value
Set range
SIM 48-5
Add 1:0.1%
increase
Reduce 1:
0.1%
decrease
1 ~ 99
(7) Off center adjustment (SIM 50-12)
a. OC mode (SIM50-12)
1) Make a test chart as shown below and set it so that its center line is
fit with the original guide center mark.
* To make a test chart, draw a line on A3 or 11" x 17" paper at the
center in the paper transport direction.
Original guide
<Adjustment specification>
Mode
Sub scanning
direction
magnification
ratio
(OC mode)
Specification
Normal
±1.0%
SIM
Set value
SIM 48-1 Add 1:0.1%
(PHOTO) increase
Reduce 1:
0.1%
decrease
Set range
1 ~ 99
Center
Copy paper
(A3 or 17" x 11")
b. SPF sub scanning direction magnification ratio (SIM48-5)
Note:
•Before performing this adjustment, be sure to check that the CCD unit is
properly installed.
•Before performing this adjustment, the OC mode adjustment in copying
must be completed.
1) Put a scale on the original table as shown below, and make a normal
(100%) copy to make a test chart.
2) Make a normal copy from the manual paper feed tray, and compare
the copy and the test chart.
If necessary, perform the following adjustment procedures.
3) Execute SIM 50-12.
4) After warm-up, shading is performed and the current set value of the
off center adjustment is displayed on the display section in 2 digits.
5) Enter the set value and press the start key.
The set value is stored and a copy is made.
<Adjustment specification>
Mode
Original off
center mode
(OC mode)
AR-5316 ADJUSTMENT 6-8
Specification
SIM
Set value
Single:
SIM 50-12 Add 1:
Center ±2.0mm (AE lamp 0.1mm shift
ON)
to R side
Reduce 1:
0.1mm shift
to L side
Set range
1 ~ 99
[06]ADJUSTMENT.fm 9 ページ
2005年7月1日 金曜日 午後5時27分
b. SPF original off-center adjustment (SIM50-12)
C.Image density adjustment
Note: Before performing this adjustment, be sure to check that the paper
off center is properly adjusted.
1) Make a test chart for the center position adjustment and set it on the
SPF.
<Adjustment specification>
(1)Copy mode (SIM 46-1)
Draw a line on a paper in the scanning direction.
2) Make a normal copy from the manual paper feed tray, and compare
the copy and the original test chart.
If necessary, perform the following adjustment procedures.
3) Execute SIM 50-12.
4) After warm-up, shading is performed and the current set value of the
off center adjustment at each paper feed port is displayed on the
display section in 2 digits.
5) Enter the set value and press the start key.
The set value is stored and a copy is made.
<Adjustment specification>
Mode
Specification
SIM
Set value
Set
range
Original off Single:
SIM Add 1:
1 ~ 99
center
Center ±3.0mm(TEXT lamp) 50-12 0.1mm shift
mode
to R side
(SPF mode)
Reduce 1:
0.1mm shift
to L side
(8) SPF white correction pixel position adjustment(SIM63-7)
(required in an SPF model when replacing the lens unit)
1) Fully open the SPF.
2) Execute SIM 63-7.
3) When the operation panel displays "COMPLETE,"the adjustment is
completed.
4) If the operation panel displays "ERROR,"perform the following
measures.
•When the display is 0:
Check that the SPF is open.
Check that the lamp is ON.(If the lamp is OFF,check the MCU connector.)
Check that the CCD harness is properly inserted into the MCU
connector.
•When the display is 281 or above:
1) Remove the table glass.
2) Remove the dark box.
3) Slide the lens unit toward the front side and attach it,then execute
SIM.
•When the display is 143 or below:
1) Remove the table glass.
2) Remove the dark box.
3) Slide the lens unit toward the rear side and attach it,then execute
SIM.
F
*
*
1)Set a test chart (UKOG-0162FCZZ) on the OC table as shown below.
2) Put several sheets of A3 or 11" x 17" white paper on the test chart.
3) Execute SIM 46-1.
4) After warm-up, shading is performed and the current set value of the
density level is displayed on the display section in 2 digits.
For mode selection, use the density select key.
5) Change the set value with the 10-key to adjust the copy image
density.
6) Make a copy and check that the specification below is satisfied.
<Adjustment specification>
Density Display Exposure Sharp Gray
mode
lamp
level
Chart output
Auto
Auto
-
Text
Text
3
Photo
Photo
3
Toner
save
Text/
Photo
3
Toner
save
Auto/
Photo
-
R
When the lens unit is moved,execute the OC main scanning
magnification ratio auto adjustment,SIM 48-1-1,IM48-3 and the PF
original off-center adjustment.
This adjustment is basically O.K.with IM 63-7.
AR-5316 ADJUSTMENT 6-9
Set value
"2" is slightly The greater the
copied.
set value is the
"3" is slightly greater the
density is The
copied.
smaller the set
"2" is slightly
value is the
copied.
smaller the
"3" is slightly density is.
copied
"2" is slightly
copied
Set
range
1 ~ 99
[07]SIMULATIONS.fm 1 ページ
2005年7月1日 金曜日 午後5時28分
[7] SIMULATIONS
Main
code
22
Sub
code
Contents
15
Trouble memory display
17
Copy counter display
18
Printer counter display
21
Scanner counter display
22
SPF jam counter display
01
Jam total counter clear
2. Canceling the simulation mode
02
Trouble memory clear
04
SPF counter clear
When the clear all key is pressed, the simulation mode is cancelled.
When the interruption key is pressed, the process is interrupted and the
screen returns to the sub code entering display.
* After canceling the simulation mode, be sure to turn OFF/ON the
power and check the operation.
06
Paper feed counter clear
07
Drum counter clear
08
Copy counter clear
09
Printer counter clear
13
Scanner counter clear
14
SPF jam total counter clear
01
Main motor operation check
10
Polygon motor operation check
02
Size setting
03
Auditor setting
05
Count mode setting
06
Destination setting
1. Entering the simulation mode
Perform the following procedure to enter the simulation mode.
"#" key
Interrupt key
"C" key
Interrupt key
Main code
Start key
Sub code
Start key
24
Note: If the machine is terminated by a jam error or paper empty during
copying in the adjustment by the simulation, recopying is required.
25
26
3. List of simulations
Main
code
Sub
code
01
01
Mirror scanning operation
07
Machine condition check (CPM)
02
Mirror home position sensor (MHPS) status display
18
Toner save mode setting
06
Mirror scanning operation aging
30
CE mark conformity control ON/OFF
01
Single paper feeder (SPF) aging
31
Auditor mode exclusive setup
02
SPF sensor status display
36
Cancel of stop at maintenance life over
03
SPF motor operation check
38
Cancel of stop at drum life over
08
SPG paper feed solenoid operation check
39
Memory capacity check
11
SPF PS release solenoid operation check
42
Transfer ON/OFF timing control setting
01
Operation panel display check
43
Side void amount setting
02
Fusing lamp and cooling fan operation check
51
Copy temporary stop function setting
03
Copy lamp lighting check
30
01
Paper sensor status display
01
Paper feed solenoid operation check
42
01
Developing counter clear
02
Resist roller solenoid operation check
43
01
Fusing temperature setting
10
Cassette semi-circular roller cleaning
12
Standby mode fusing fan rotation setting
01
Warm-up display and aging with jam
13
Fusing paper interval control allow/inhibit setting
06
Intermittent aging
34
Transfer current setting
08
Shifting with warm-up display
40
Setting of rotation time before toner supply
01
Developing bias output
01
Copy density adjustment (300dpi)
02
Main charger output (Grid = HIGH)
02
Copy density adjustment (600dpi)
03
Main charger output (Grid = LOW)
09
06
Transfer charger output
Copy exposure level adjustment, individual setting
(Text) 300dpi
10
Copy exposure level adjustment, individual setting
(Text) 600dpi
11
Copy exposure level adjustment, individual setting
(Photo) 600dpi
02
05
06
07
08
Contents
44
46
10
-
Toner motor operation
14
-
Trouble cancel (except for U2)
16
-
U2 trouble cancel
20
01
Maintenance counter clear
21
01
Maintenance cycle setting
18
Image contrast adjustment (300dpi)
22
01
Maintenance counter display
19
02
Maintenance preset display
03
Jam memory display
Exposure mode setting
(Gamma table setting/AE operation mode setting/
Photo image process setting)
04
Jam total counter display
20
SPF exposure correction
05
Total counter display
29
Image contrast adjustment (600dpi)
08
SPF counter display
30
AE limit setting
09
Paper feed counter display
31
Image sharpness adjustment
12
Drum counter display
01
Main scanning magnification ratio adjustment
13
CRUM type display
05
SPF mode sub scanning magnification ratio adjustment
in copying
14
P-ROM version display
48
49
01
Flash ROM program writing mode
12
Standby mode fusing fan RPM setting
AR-5316 SIMULATIONS 7-1
[07]SIMULATIONS.fm 2 ページ
Main
code
50
2005年7月1日 金曜日 午後5時28分
Sub
code
Contents
01
Image lead edge adjustment
06
Copy lead edge position adjustment (SPF)
10
Paper off-center adjustment
12
Document off-center adjustment
51
02
Resist amount adjustment
53
08
SPF scanning position automatic adjustment
10
SPF scan position change-over setting
61
03
HSYNC output check
63
01
Shading check
07
SPF automatic correction
01
Self print
64
4. Contents of simulations
Main Sub
code code
Contents
Details of operation
01
06
Mirror scanning operation aging
When the [START] key is pressed, the mirror base performs A3(11” x 17”) full scanning at the set
magnification ratio speed. During scanning, the set magnification ratio is displayed. After 3 seconds,
the mirror base performs full scanning again. During scanning, the set magnification ratio is
displayed.
* When the [START] key is pressed again, the ready lamp turns and remains off.
The DV replacement/OPC drum cartridge replacement lamp displays the status of the mirror
home position sensor. (The lamp lights up when the mirror is in the home position.)
During aging, the copy lamp lights up. When the [Interrupt] key is pressed, the operation is
interrupted if operating, and the machine goes into the sub code input standby mode.
02
01
Single paper feeder (SPF) aging
When the [START] key is pressed, the set magnification ratio is acquired and document transport
operation of single surface is performed in the case of SPF. During operation, the LED on the display
section corresponding to the selected magnification ratio lights up, and the magnification ratio is
displayed on the 7-seg display. When the [Interrupt] key is pressed at that time, the machine goes to
the sub code input standby mode. When the [CA] key is pressed, the simulation is terminated.
02
SPF sensor status display
(In order to receive the sensor change notification, the load must be decreased.)
The sensor status (ON/OFF) in the SPF can be checked with the following lamps.
When a sensor detects paper, it turns on. The open/close detection sensor turns on when the
machine is opened.
Display lamp
Sensor
Toner supply lamp
Copier jam lamp
The DV replacement/OPC drum cartridge
replacement lamp
Paper empty lamp
SPF jam lamp
Manual paper feed lamp
Tray jam lamp
AE lamp
TEXT lamp
PHOTO lamp
SPF document set sensor
SPF document transport sensor
SPF unit (OC cover) open/close sensor
SPF paper exit sensor
SPF paper feed cover open/close sensor
SPF paper length sensor 1
SPF paper length sensor 2
SPF paper feed width sensor (small)
SPF paper feed width sensor (middle)
SPF paper feed width sensor (large)
When the [Interrupt] key is pressed, the machine goes to the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
06
01
Paper feed solenoid operation
check
When this simulation is executed, the sub code is displayed on the 7-seg LED and the lamp
corresponding to the solenoid lights up.
Select a solenoid with the tray select key (the lamp corresponding to the solenoid lights up) and
press the [START] key, and the machine repeats operation of ON for 500ms and OFF for 500ms.
This operation is repeated 20 times.
After that, the machine goes into the sub code entry standby mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
Display lamp
Main cassette lamp
Manual paper feed lamp
AR-5316 SIMULATIONS 7-2
Solenoid
Main cassette paper feed solenoid
Manual paper feed solenoid
[07]SIMULATIONS.fm 3 ページ
Main Sub
code code
06
08
2005年7月1日 金曜日 午後5時28分
Contents
Details of operation
02
Resist roller solenoid operation
check
When the [START] key is pressed in the sub code input state, the resist solenoid (RRS) turns ON for
500ms and OFF for 500ms. This operation is repeated 20 times.
After completion of the process, the machine goes into the sub code input standby mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
10
Cassette semi-circular roller
cleaning
First of all, remove the developer unit.
Enter the simulation code, specify the cassette to be cleaned with the tray select key, and press
START button. The main motor rotates to move the cassette semi-circular roller by half circle and
make the roller face downward.
After completion of cleaning, when INTERRUPT key is pressed, the machine goes into the sub code
entry standby mode and the roller returns to the original positions.
To clean another roller continuously, press INTERRUPT key to return the roller to the original
position, and execute the simulation again.
During the operation, the sub code is displayed on the display.
* When CA key is pressed, the simulation mode is terminated.
However, the roller returns to the original position by the initial operation.
01
Developing bias output
When the [START] key is pressed, the developing bias signal is turned ON for 30 sec.
However, to calculate the actual output value is calculated, execute SIM25-01.
After completion of the process, the machine goes into the sub code input standby mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
02
Main charger output (Grid = HIGH) When the [START] key is pressed, the main charger output is supplied for 30 sec in the grid voltage
HIGH mode. After completion of the process, the machine goes into the sub code input standby
mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
03
Main charger output (Grid = LOW) When the [START] key is pressed, the main charger output is supplied for 30 sec in the grid voltage
LOW mode. After completion of the process, the machine goes into the sub code input standby
mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
06
Transfer charger output
Select an output mode with the [Mode select] key and press the [START] key. The transfer charger
output is delivered for 30 sec in the selected mode.
After 30 sec of transfer charger output, the machine goes into the sub code entry standby mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
Display lamp
Output mode
AE mode lamp
AE mode lamp & PHOTO mode lamp
AE & TEXT & PHOTO mode lamp
21
1
Maintenance cycle setting
Normal size width: Front surface
Small size width: Front surface
Manual paper feed mode
•Small size is Letter R (A4R) or smaller.
The current set maintenance cycle code is displayed (initial display), and the set data are stored.
Code
0
1
22
Setting
150,000 sheets
Free (999,999 sheets)
* Default
01
Maintenance counter display
The maintenance counter value is displayed. (Alternate display by 3 digits)
04
Jam total counter display
The jam total counter value is displayed. (Alternate display by 3 digits)
05
Total counter display
The total counter value is displayed. (Alternate display by 3 digits)
08
SPF counter display
The SPF counter value is displayed. (Alternate display by 3 digits)
13
CRUM destination display
When this simulation is executed, the CRUM destination set (written) in the CRUM chip is displayed.
If the display does not match the destination code saved in the CRUM chip, it is judged as an error.
*This simulation is valid only for the models where the CRUM is valid.
7-seg display
00
01
02
03
Meaning (CRUM destination)
Not set yet
BTA-A
BTA-B
BTA-C
AR-5316 SIMULATIONS 7-3
7-seg display
04
12
11
Meaning (CRUM destination)
BTA-E
AL series
AR-5316(for SEC)
[07]SIMULATIONS.fm 4 ページ
Main Sub
code code
22
30
14
2005年7月1日 金曜日 午後5時28分
Contents
P-ROM version display
Details of operation
The P-ROM version is displayed on the copy quantity display. The main code and the sub code are
alternatively displayed by 2 digits. The display interval is same as that of the counter display.
By pressing the fixed magnification ratio key, each version display is switched.
Display lamp (AB series)
Display lamp (Inch series)
141%
141%
17
Copy counter display
The copy counter value is displayed. (Alternate display by 3 digits) When the [Interrupt] key is
pressed, the machine goes into the sub code input standby mode. When the [CA] key is pressed, the
simulation is terminated.
18
Printer counter display
The printer counter value is displayed. (Alternate display by 3 digits)When the [Interrupt] key is
pressed, the machine goes into the sub code input standby mode. When the [CA] key is pressed, the
simulation is terminated.
21
Scanner counter display
The scanner counter value is displayed. (Alternate display by 3 digits)When the [Interrupt] key is
pressed, the machine goes into the sub code input standby mode. When the [CA] key is pressed, the
simulation is terminated.
22
SPF jam counter display
The SPF jam counter value is displayed. (Alternate display by 3 digits)When the [Interrupt] key is
pressed, the machine goes into the sub code input standby mode. When the [CA] key is pressed, the
simulation is terminated.
01
Paper sensor status display
The paper sensor status is displayed with the lamps on the operation panel.
* When each sensor detects paper, the corresponding lamp turns on.
Display lamp
Developer lamp
Toner lamp
Manual paper feed lamp
No. 1 cassette lamp
Zoom lamp
44
Displayed version
Machine program
34
Transfer current setting
Sensor name
Paper exit sensor
Paper entry sensor
Manual feed paper empty sensor
No. 1 tray paper empty sensor
New drum detect sensor
Used to set the transfer current for the front surface and that for the back surface. When this
simulation is executed, the current set value is displayed on the 7-seg display. Select the set value
with the zoom (Up/Down) keys and press the [START] key, and the set content is written into the
EEPROM and the machine goes into the sub code input standby mode. Press the [Mode select] key
to select each setting mode. At that time, the setup content is written into the EEPROM.
The set range is 90uA ~ 360uA in the increment of 10uA.
Display lamp
Setting mode
AE mode lamp
AE mode lamp & PHOTO mode lamp
AE & TEXT & PHOTO mode lamps
*
*
Normal size width: Front
Small size width: Front
Manual paper feed
Small size paper must be Letter R (A4R) or smaller.
For the special size of tray, use the normal size width.
AR-5316 SIMULATIONS 7-4
[07]SIMULATIONS.fm 5 ページ
Main Sub
code code
46
19
2005年7月1日 金曜日 午後5時28分
Contents
Exposure mode setting
(Gamma table setting / AE
operation mode setting / PHOTO
image process setting)
Details of operation
Used set for the following three exposure mode. Enter a code number and press the [START] key,
and the entered number is written into the EEPROM and the machine goes into the sub code entry
standby mode. (When the [Copy mode select] key is pressed, the number is written into the
EEPROM and the set item is changed.)
<<Gamma table setting>>
When this simulation is executed, the current set code number of gamma table is displayed.
(Default: Japan -1. EX Japan -2)
*
When setting the gamma table, no "Mode lamps" are lighted.
Code number
Setting (Gamma table)
1
2
Image quality priority mode
Toner consumption priority mode
* Default for Japan models
* Default for EX Japan models
* If this setting is changed, the set content of SIM46-30 is reset to the default.
<<AE mode>>
When the [Copy mode select] key is pressed in gamma table setting, the mode is changed to the AE
operation mode setting and the current set code number of the AE operation mode is displayed.
(Default: 0)
* When setting the AE operation mode, the "AE mode lamp" is lighted.
Code number
0
1
Setting (AE operation mode)
Lead edge stop
Rear time process
* Default
<Photo image process setting>
When the [Copy mode select] key is pressed during the AE operation mode setting, the setting mode
is changed to the photo image process setting and the currently set code number of the photo image
process setting is displayed.
* When in the photo image process setting, the [Photo mode lamp] is lighted.
Code number
1
2
*
49
01
Flash ROM program writing mode
Setting (Photo image process setting)
Error diffusion process
Dither process
* Default
When this setting is changed, SIM 46-1/2/18/29 and SIM 46-31 Photo items are reset to the
default. (SIM 46-11 is also linked.)
(Operating procedure)
When this simulation is executed, "d" is displayed on the copy quantity display and the machine
enters the Flash ROM program writing mode. Use the writing tool on the PC to write the program.
During writing, the display is made as follows. After completion of downloading, turn OFF/ON the
power to reset.
Status
Download data reception
Data delete start
Data writing (Boot section)
Data writing (Program section)
Sum check
Completion of downloading
Error status
*
Copy quantity display
"d"
"d"
"d"
"d"
"d"
"OFF"
"*E"
Pre-heat lamp
ON
ON
Flash
Flash
ON
OFF
OFF
Ready lamp
OFF
ON
OFF
Flash
ON
OFF
OFF
"*" in the error display indicates the error position.
00
02
03
04
05
06
Data receive error
FLASH ROM delete error
FLASH ROM write error (Boot section)
FLASH ROM write error (Program section)
Sum check error (Loader section)
Sum check error (Boot section)
AR-5316 SIMULATIONS 7-5
07
08
09
0b
0F
Sum check error (Program section)
Sum check error (EEPROM section)
E2PROM verify error
E2PROM verify error
Download data length error
[07]SIMULATIONS.fm 6 ページ
Main Sub
code code
49
12
2005年7月1日 金曜日 午後5時28分
Contents
Standby mode fusing fan RPM
setting
Details of operation
When this simulation is executed, the currently set code number is displayed.
When [MODE SELECT] key is pressed, the normal setting and the high fusing temperature setting
are switched alternatively.
Enter the code number and press START key, and the number is written into the EEPROM and the
machine goes into the sub code entry standby mode.
Display lamp
Setting mode
Normal temperature control (190°C or less)
Low speed rotation
TEXT mode
Fusing temperature of 190°C or above
High speed rotation
Code number
0
1
51
02
Resist amount adjustment
Default
AE mode lamp
Setting
Low speed rotation
High speed rotation
Used to adjust the contact pressure of the machine resist roller and the SPF resist roller onto the
paper.
(Operating procedure)
When this simulation is executed, the current set value is displayed.
When the exposure mode key is pressed, the following set items are changed sequentially. Enter an
adjustment value with the 10-key and press the [START] key, and the entered value will be saved and
a copy will be made. (Adjustment range: 1 ~ 99, Default: 50)
When the [CA] key is pressed, the entered value is saved and the simulation is terminated.
Lighting lamp
Adjustment mode
Main cassette paper feed
Manual paper feed
SPF document feed
AE, Main cassette lamp
AE, Manual paper feed lamp
AE, TEXT, PHOTO lamps
Supported for the installed models only. Skipped for the models without installation.
53
10
SPF scan position change-over
setting
Used to change over the scan position depending on that the SPF unit and the SPF document glass
holder section are of anti-dirt glass or not.
When this simulation is executed, the currently set code number is displayed.
Enter the code number corresponding to the SPF unit to be used and press [START] key, and the
setting will be changed over.
Code No.
Mode
0
Set to the scan position of the current mass production SPF unit. (Default)
1
Set to the scan position of the ant-dirt SPF unit.
Though this setting is changed, the other set values are not affected. (The other set values remain
unchanged.)
When replacing and installing the SPF unit, it is recommendable to use this simulation to set the
scan position and execute the scan position automatic adjustment.
64
01
Self print
The optical system status is ignored and a self print is made. Also when a print command is sent
from the host, printing is performed.
(Operating procedure)
When this simulation is executed, warm-up is performed and the ready lamp is lighted.
(However, the scanner is invalid and no initial operation is made.)
Enter the code number with the 10-key, and select a cassette with the cassette select key and press
the [START] key. The selected cassette start paper feed and printing is performed in the selected
pattern.
* Only the tray lamp and the online lamp are lighted, and no other lamps are lighted.
Printing is made in 1 by 2 mode, where one line is printed and the following two liens are not printed,
or in the grid pattern.
Code number
0
1
2
3
*
*
Pattern
1 by 2
Grid pattern
White paper
Black background
Input disable for 4 ~ 99
Print data are made on A3(11” x 17”) size. (A3(11” x 17”) paper is preferable.)
AR-5316 SIMULATIONS 7-6
[08]USERPROGRAMS.fm 1 ページ
2005年7月1日 金曜日 午後5時28分
[8] USER PROGRAMS
The user programs allow the parameters of certain functions to be set, changed, or canceled as desired.
1. List of user programs
This copier has the following user programs.
Program name
Program
No
Auto clear time
1
Description
"Auto clear time" automatically returns the copy settings to the initial
settings when a certain period of time elapses after a copy is made.
This program is used to select the period of time. "Auto clear time"
can also be disabled.
Default
Parameters
1 (OFF)
2 (10sec)
60sec
3 (20sec)
4 (60sec)
5 (90sec)
6 (120sec)
Preheat mode
2
Auto power shut-off timer
3
Stream feeding mode *1
4
Auto power shut-off
setting
Auditing mode
Account number entry
Account number change
5
Resetting account
Resolution in Auto/Text
mode
This function automatically switches the machine to a state that
consumes even less power than preheat mode if the set duration of
time elapses without the machine being used when the power is on.
All lights except the POWER SAVE indicator and ON LINE indicator
go off. To resume normal operation, press the [START] key. Normal
operation also resumes automatically when a print job is received or
scanning is begun from a computer. While in auto power shut-off
mode, no keys (except the [START] key) can be used.
When copying using the SPF, during the period of time that the SPF
indicator blinks after an original has been scanned (about 5
seconds), a subsequent original can be placed and automatically
fed into the machine.
Use this setting to enable or disable auto power shut-off.
10
Use to enable or disable "Auditing mode".
"Auditing mode" is initially disabled.
11
Use to set up account numbers.
Up to 20 accounts can be established.
1 (1min)
2 (5min)
1min
1 (5min)
2 (30min)
3 (60min)
5min
4 (120min)
5 (240min)
0 (OFF)
OFF
ON
OFF
1 (ON)
0 (OFF)
1 (ON)
0 (OFF)
1 (ON)
-
Use to change an account number.
13
Delete
single
account
14
This displays the number of copies made by each account.
The maximum count is 49,999. If this number is exceeded, the count
will start over from 0.
-
15
Use to reset the copy count of an account to 0.
The copy count of a single account or of all accounts can be reset.
23
This setting is used to change the copy resolution in AUTO and
TEXT mode from 600 x 300 dpi to 600 x 600 dpi
(high-quality mode).
Scanning is slower when high-quality mode is used.
AR-5316 USER PROGRAMS 8-1
4 (60min)
6 (240min)
Use to delete an account number.
A single account number can be deleted, or all account numbers at
once.
*1 When the SPF is installed.
3 (30min)
5 (120min)
12
Account number deletion
Number of copies per
account
This function automatically switches the machine to a low power
consumption state if the set duration of time elapses without the
machine being used when the power is on.
The POWER SAVE indicator lights up, however, the keys on the
operation panel can be used. Normal operation automatically
resumes when a key on the operation panel is pressed, a print job is
received or an original is placed.
-
-
0 (Delete single account)
1 (Delete all accounts)
-
Reset single 0 (Reset single account)
account
1 (Reset all accounts)
1 (300dpi)
300dpi
2 (600dpi)
[08]USERPROGRAMS.fm 2 ページ
Program name
2005年7月1日 金曜日 午後5時28分
Program
No
Description
25
Use this setting to select whether or not holding down a key causes
repeated input of the key. For keys that normally cause a set value to
increase when held down (for example, holding down the [ZOOM]
key), this program can be used to have the set value not change
when the key is held down.
Key auto repeat
Key press time
Use this setting to select how long a key must be pressed for the
input to be accepted. By selecting a longer time, you can prevent
settings from being changed by the accidental pressing of a key.
26
Default
Parameters
0 (OFF)
1 (ON)
ON
Minimum
(current
response
speed)
1 (Minimum
(current response speed))
2 (0.5sec)
3 (1.0sec)
4 (1.5sec)
5 (2.0sec)
Audible signals volume
This sets the volume of beep signals.
27
1 (short beep)
short beep 2 (long beep)
3 (OFF)
Base setting beep signal
Number of copies limit
28
Use this to sound a beep when a base setting is selected.
OFF
29
Use this setting to select 99 or 999 for the maximum number of
copies.
30
When this function is enabled, printing in printer mode will
automatically continue using a different size of paper if the specified
size of paper runs out in all trays. This feature does not function in
copy mode.
OFF
31
Use this program to select a default tray. This tray is automatically
selected each time the power is turned on or each time the machine
reverts to the initial settings.
Upper
paper tray
Use close paper size
Default tray setting
Default exposure mode
32
Use this program to set "AUTO", "TEXT", or "PHOTO" as the default
exposure mode.
999 copies
0 (OFF)
1 (ON)
1 (99 copies)
2 (999 copies)
0 (OFF)
1 (ON)
1 (Tray 1)
5 (Bypass tray)
1 (AUTO)
AUTO
2 (TEXT)
3 (PHOTO)
AR-5316 USER PROGRAMS 8-2
[09]TROUBLECODE.fm 1 ページ
2005年7月1日 金曜日 午後5時28分
[9]TROUBLE CODE LIST
2.Details of trouble codes
Main Sub
code code
1.Trouble code list
Main code
E1
Sub
code
00
IMC PWB communication trouble
10
IMC PWB trouble
11
IMC ASIC error
13
IMC PWB flash ROM error
16
IMC PWB DIMM memory read/write check error
81
Interface error in communication with IMC PWB
(Parity)
82
Interface error in communication with IMC PWB
(Overrun)
84
E7
F2
E1
Content
00
10
Interface error in communication with IMC PWB
(Framing)
Cause
IMC PWB-MCU PWB harness abnormality
MCU PWB connector disconnection
IMC PWB ROM defect/data abnormality
Check
and
remedy
Check connection of the connector and the
harness between the IMC PWB and the MCU
PWB.
Check the ROM of the IMC PWB.
Content
IMC PWB trouble
Detail
An abnormality occurs in the IMC PWB.
Cause
USB chip error/CODEC error on the IMC PWB
Check
and
remedy
Replace the IMC PWB with a new one.
LSU trouble
11
Shading trouble (White correction)
Content
IMC ASIC error
12
Shading trouble
Detail
An abnormality occurs in the IMC PWB.
16
Abnormal laser output
Cause
Abnormality in ASIC on the IMC PWB
04
Improper cartridge (destination error, life cycle
error)
Check
and
remedy
Replace the IMC PWB with a new one.
11
Content
IMC PWB flash ROM error
Type error
13
Detail
An abnormality occurs in the IMC flash ROM.
Destination error
Cause
IMC PWB abnormality
Data abnormality
Check
and
remedy
Replace the IMC PWB with a new one.
If downloading of the program is abnormally
terminated, it may cause an error. Download
the program again to avoid this.
02
Content
IMC PWB DIMM memory read/write check
error
Detail
An installation error occurs in the IMC
expansion compression memory module.
An error occurs during access to the IMC
expansion compression memory.
Cause
Improper installation of the IMC expansion
memory module.
IMC expansion memory module abnormality
IMC expansion memory contact abnormality
IMC PWB abnormality.
Check
and
remedy
Check installation of the expansion memory
module.
Replace the expansion memory module.
Replace the IMC PWB with a new one.
Content
Interface error (Parity) in communication with
the IMC PWB
Detail
A parity error occurs in communication
between the MCU PWB and the IMC PWB.
Cause
IMC PWB-MCU PWB harness defect
Improper connection of the MCU PWB
connector
IMC PWB ROM defect/data abnormality"
Check
and
remedy
Check connection of the connector/harness
between the IMC PWB and the MCU PWB.
Check the ROM of the IMC PWB.
Copy lamp lighting abnormality
H2
00
Thermistor open
H3
00
Heat roller high temperature detection
H4
00
Heat roller low temperature detection
L1
00
Scanner feed trouble
L3
00
Scanner return trouble
L4
01
Main motor lock detection
11
Shifter motor trouble
L6
10
Polygon motor lock detection
L8
01
No full wave signal
U2
04
EEPROM read/write error (serial communication
error)
11
Counter check sum error (EEPROM)
12
Adjustment value check sum error (EEPROM)
40
CRUM chip communication error
CH ON
An abnormality occurs in communication
between the MCU PWB and the IMC PWB.
Shading trouble (Black correction)
Misc error
CH Blink
IMC PWB communication trouble
Detail
10
Model error
--
Content
02
Identification error
F5
Details of trouble
Auditor NOT READY
None Side door open
None Developing cartridge not installed
16
81
AR-5316 TROUBLE CODE LIST 9-1
[09]TROUBLECODE.fm 2 ページ
2005年7月1日 金曜日 午後5時28分
Main Sub
code code
E1
82
84
Details of trouble
Content
02
10
Interface error (Overrun) in communication with
the IMC PWB
Detail
An overrun error occurs in communication
between the MCU PWB and the IMC PWB.
Cause
IMC PWB-MCU PWB harness defect
Improper connection of the MCU PWB
connector
IMC PWB ROM defect/data abnormality.
Check
and
remedy
Check connection of the connector/harness
between the IMC PWB and the MCU PWB.
Check the ROM of the IMC PWB.
Content
Interface error (Framing) in communication with
the IMC PWB
Detail
A framing error occurs in communication
between the MCU PWB and the IMC PWB.
Cause
IMC PWB-MCU PWB harness defect
Improper connection of the MCU PWB
connector
IMC PWB ROM defect/data abnormality.
Check
and
remedy
E7
Main Sub
code code
E7
11
12
Check connection of the connector/harness
between the IMC PWB and the MCU PWB.
Check the ROM of the IMC PWB.
Content
LSU trouble
Detail
The BD signal from the LSU cannot be
detected in a certain cycle. (Always OFF or
always ON)
Cause
LSU connector or LSU harness defect or
disconnection
Polygon motor rotation abnormality
Laser beams are not generated.
MCU PWB abnormality.
Check
and
remedy
Check connection of the LSU connector.
Execute SIM 61-03 to check the LSU
operations.
Check that the polygon motor rotates normally.
Check that the laser emitting diode generates
laser beams.
Replace the LSU unit.
Replace the MCU PWB.
Content
Shading trouble (Black correction)
Detail
The CCD black scan level is abnormal when
the shading.
Cause
Improper connection of the CCD unit flat cable
CCD unit abnormality
MCU PWB abnormality.
Check
and
remedy
Check connection of the CCD unit flat cable.
Check the CCD unit."
16
F2
04
Details of trouble
Content
Shading trouble (White correction)
Detail
The CCD white scan level is abnormal when
the shading.
Cause
Improper connection of the CCD unit flat cable
Dirt on the mirror, the lens, and the reference
white plate
Copy lamp lighting abnormality
CCD unit abnormality
MCU PWB abnormality
(When occurred in the SPF scan position.)
Improper installation of the mirror unit
Check
and
remedy
Clean the mirror, lens, and the reference white
plate.
Check the light quantity and lighting status of
the copy lamp (SIM 05-03).
Check the MCU PWB.
Content
Shading trouble
Detail
White correction is not completed in the
specified number of operations.
Cause
CCD unit flat cable connection failure.
Dirt on mirrors, lenses, and the reference white
plate.
Copy lamp lighting abnormality
CCD unit abnormality
MCU PWB abnormality
Check
and
remedy
Clean mirrors, lenses, and the reference white
plate.
Check the copy lamp light quantity (SIM 05-03)
and lighting.
Check the CCD unit.
Check the MCU PWB.
Content
Abnormal laser output
Detail
When the laser output is stopped, HSYNC is
detected.
Cause
Laser abnormality
MCU PWB abnormality.
Check
and
remedy
Check the laser emitting diode operation.
Replace the MCU PWB. "
Content
Improper cartridge (Destination error, life cycle
error)
Detail
The destination of the machine differs from that
of the CRUM.
The life cycle information is other than "Not
used (FFh)."
Cause
CRUM chip defect
Improper developing unit
Check
and
remedy
Replace the CRUM chip.
Replace the developing unit.
Identificat The trade mark code of the CRUM differs.
ion error The company code of the CRUM differs.
Model
error
The boot program model code does not
coincide with the CRUM model code.
Type error When the CRUM type is other than genuine/
conversion/production rotation.
Destinatio The machine destination differs from the
n error
CRUM destination.
Data
When an error value is included in the initial
abnormali check information. When the max. toner supply
ty
time is 00.
When the print hard stop is 00.
Misc error When the Misc information is other than "Not
used (FFh)."
AR-5316 TROUBLE CODE LIST 9-2
[09]TROUBLECODE.fm 3 ページ
Main Sub
code code
F5
H2
H3
02
00
00
2005年7月1日 金曜日 午後5時28分
Details of trouble
Main Sub
code code
Content
Copy lamp lighting abnormality
Detail
The copy lamp does not turn on.
Cause
Copy lamp abnormality
Copy lamp harness abnormality
CCD PWB harness abnormality.
Check
and
remedy
Use SIM 5-3 to check the copy lamp
operations.
When the copy lamp lights up.
Check the harness and the connector between
the CCD unit and the MCU PWB.
When the copy lamp does not light up.
Check the harness and the connector between
the copy lamp unit and the MCU PWB.
Replace the copy lamp unit.
Replace the MCU PWB. "
H4
Content
Thermistor open
Detail
The thermistor is open.
The fusing unit is not installed.
Cause
Thermistor abnormality
Control PWB abnormality
Fusing section connector disconnection
The fusing unit is not installed.
Check
and
remedy
Check the harness and the connector between
the thermistor and the PWB.
Use SIM 14 to clear the self diagnostic display.
Content
Heat roller high temperature detection
Detail
The fusing temperature exceeds 240C°.
Cause
Thermistor abnormality
Control PWB abnormality
Fusing section connector disconnection.
Check
and
remedy
Use SIM 5-02 to check the heater lamp blinking
operation.
When the lamp blinks normally.
Check the thermistor and its harness.
Check the thermistor input circuit on the control
PWB.
When the lamp keeps ON.
Check the power PWB and the lamp control
circuit on the MCU PWB.
Use SIM 14 to clear the self diagnostic display.
L1
L3
00
00
00
Details of trouble
Content
Heat roller low temperature detection
Detail
When the fusing temperature is lower than
150C° after 55sec from the start of warming
up.
When the warming up complete temperature is
not reached in 30sec from reaching 150C°.
When the fusing temperature is lower than
100C° after 20sec from ready start.
When the fusing temperature is lower than
145C° when printing."
Cause
Thermistor abnormality
Heater lamp abnormality
Thermostat abnormality
Control PWB abnormality
Check
and
remedy
Use SIM 5-02 to check the heater lamp blinking
operation.
When the lamp blinks normally.
Check the thermistor and its harness.
Check the thermistor input circuit on the control
PWB.
When the lamp does not light up.
Check for disconnection of the heater lamp and
the thermostat. Check the interlock switch.
Check the power PWB and the lamp control
circuit on the MCU PWB.
Use SIM 14 to clear the self diagnostic display.
Content
Scanner feed trouble
Detail
The scanner does not complete feeding in the
specified time.
Cause
Mirror unit abnormality
The scanner wire is disconnected.
The origin detection sensor abnormality
Mirror motor harness abnormality
Check
and
remedy
Use SIM 1-1 to check the mirror reciprocating
operations.
When the mirror does not feed.
Check for disconnection of the scanner wire.
Check the harness and the connector between
the mirror motor and the MCU PWB.
Replace the mirror unit.
Replace the MCU PWB.
When the mirror does feed.
Use SIM 1-2 to check the mirror home position
sensor."
Content
Scanner return trouble
Detail
The scanner does not complete returning in
the specified time.
The mirror is not in the home position when OC
copying is started with the mirror standby in the
home position.
Cause
Mirror unit abnormality
Scanner wire disconnection
Origin detection sensor abnormality
Mirror motor harness abnormality
Check
and
remedy
Use SIM 1-1 to check the mirror reciprocating
operations.
When the mirror does not return.
Check for disconnection of the scanner wire.
Check the harness and the connector between
the mirror motor and the MCU PWB.
Replace the mirror unit.
Replace the MCU PWB.
When the mirror does feed.
Use SIM 1-2 to check the mirror home position
sensor.
AR-5316 TROUBLE CODE LIST 9-3
[09]TROUBLECODE.fm 4 ページ
Main Sub
code code
L4
01
L6
10
Content
Main motor lock detection
Detail
The main motor does not rotate.
The motor lock signal is detected for 1sec or
more after rotation of the main motor.
The motor lock signal is detected for 1sec
during rotation of the main motor.
U2
01
04
U2
Main motor unit abnormality
Improper connection or disconnection the main
motor and the harness.
MCU PWB abnormality
11
12
Details of trouble
Content
Counter check sum error (EEPROM)
Detail
Check sum error of the counter area in the
EEPROM
Cause
EEPROM abnormality
Check
and
remedy
Check that the EEPROM is properly set.
Use SIM 16 to cancel the trouble.
Replace the MCU PWB.
Content
Adjustment value check sum error (EEPROM)
Detail
Check sum error of the adjustment value area
in the EEPROM
Check
and
remedy
Use SIM 25-01 to check the main motor
operations.
Check connection of the main motor harness/
connector.
Replace the main motor.
Replace the MCU PWB.
Content
CRUM chip communication error
Content
Shifter motor trouble
Detail
Detail
The shifter home position detection signal is
not detected when initializing the shifter.
An error occurs during communication
between the MCU and the CRUM chip.
Cause
Cause
Shifter motor abnormality, improper connection
or disconnection of the harness, shifter home
position sensor abnormality
CRUM chip abnormality
Developing unit disconnection
MCU PWB abnormality
Check
and
remedy
Use SIM 03-11 to check the shifter motor
operations.
Check connection of the harness/connector of
the shifter motor.
Replace the shifter motor.
Replace the MCU PWB.
Check
and
remedy
Replace the chip.
Check installation of the developing unit.
Use SIM 16 to cancel the trouble.
Replace the MCU PWB.
Content
Auditor NOT READY
Content
Polygon motor lock detection
Detail
The polygon motor does not rotate.
The motor lock signal is detected for 6sec after
rotation of the polygon motor. The motor lock
signal is detected for 1sec during rotation of the
polygon motor.
Cause
L8
Main Sub
code code
Details of trouble
Cause
11
2005年7月1日 金曜日 午後5時28分
Polygon motor unit abnormality
Improper connection or disconnection of the
polygon motor and the harness.
MCU PWB abnormality
Check
and
remedy
Use SIM 61-1 to check the polygon motor
operations.
Check connection of the polygon motor
harness/connector.
Replace the polygon motor..
Replace the MCU PWB.
Content
No full wave signal
Detail
The zero cross signal is not detected.
Cause
Power unit abnormality
MCU PWB abnormality
Check
and
remedy
Check connection of the harness and
connectors.
Replace the MCU PWB.
Replace the power unit.
Content
EEPROM read/write error (Serial
communication error)
Detail
EEPROM access process error
Cause
EEPROM abnormality
Check
and
remedy
Check that the EEPROM is properly set.
Use SIM 16 to cancel the trouble.
Replace the MCU PWB.
40
--
Cause
EEPROM abnormality
Check
and
remedy
Check that the EEPROM is properly set.
Use SIM 16 to cancel the trouble.
Replace the MCU PWB.
Detail
Cause
Check
and
remedy
CH
ON
None Content
Side door open
Detail
The side door is open.
Cause
Side door sensor abnormality
MCU PWB abnormality
Check
and
remedy
Check that all the side doors are closed.
Replace the MCU PWB.
CH None Content
Blink
Detail
Developing cartridge not installed
The developing cartridge is not installed.
Communication with the CRUM cannot be
made in initial check of the CRUM.
Cause
Developing unit disconnection
MCU PWB abnormality
CRUM chip abnormality
Check
and
remedy
Check installation of the developing unit.
Replace the MCU PWB.
AR-5316 TROUBLE CODE LIST 9-4
[10]MAINTENANCE.fm 1 ページ
2005年7月1日 金曜日 午後5時29分
[10] MAINTENANCE
2. Maintenance display system
Toner
1. Maintenance table
LED
Near Empty: Illuminate
Empty
: Blink
X:Check(Clean, adjust, or replace when required.)
O:Clean :Replace :Adjust
:Lubricate
Unit name
Optical
section
Part name
Lamp unit
O
Mirror
O
No.2/3
mirror unit
Mirror
O
Pulley
X
CCD
peripheral
Lens
O
Glass
Other
Table glass
O
White Plate
O
Drive wire
Rail
Document cover
LSU
Paper feed
section
Multi paper
feed
section
O
O
Dust-proof glass
O
Take-up roller
(manual / SPF)
O
Paper feed roller
Drum
O
O
Transport (paper exit)
rollers
O
Machine
Near Empty: Active (about 300 page remains)
Empty: Stop
Life: 30K
LED&Machine
LED illuminate at 29K.
After the LED illuminates, if another 1K copies are
made the light will start blinking and the machine will
stop.
(Whether the machine will stop at 30K or not can be
selected by service simulation setting.)
Maintenance LED
Illuminate at 150K. (for upper heat roller)
Not illuminating can be selected by service man
simulation setting.
Default: illuminate at 150K
Choice: 150K or Free(not illuminating)
Machine
Whether the machine will stop at 150K or not can be
selected by service simulation setting.
Default: Free (not stop)
Choice: stop at 150K or Free
O
PS roller
Spring clutch
Fusing
section
X
X
Document size sensor
Spring clutch
Paper
transport
section
When
calling
Reflector
Life: 9K
O
Upper heat roller
O
Pressure roller
O
3. Note for replacement of consumable parts
Pressure roller bearing
X
Upper separation pawl
X
A. TD cartridge
Lower separation pawl
X
Cleaning pad
X
Drive
section
Gears
Belts
X
Paper exit
section
Ozone filter
X
When a waste toner cartridge is removed from the machine, it must be
put in a polyethylene bag to avoid scattering of toner.
X
B. Drum cartridge
Do not shake or put up the developer cartridge. Otherwise developer
may scatter.
AR-5316 MAINTENANCE 10-1
[11]DISASSEMBLY.fm 1 ページ
2005年7月1日 金曜日 午後5時29分
[11]DISASSEMBLY AND ASSEMBLY
B.Charger wire
WARNING Before performing the disassembly procedure, be sure to
remove the power cord to prevent against an electric shock.
Installation: The spring tip must be between two reference ribs.
•The charger wire must be free from twist or bending.
•Be sure to put the charger wire in the V groove.
No.
1
Item
High voltage section
2
Optical section
3
Fusing section
4
Paper exit section
5
MCU
6
Optical frame unit
7
LSU
8
Tray paper feed section/Paper transport section
9
Manual multi paper feed section
10
Power section
11
Developing section
12
Process section
13
Others
(1)
(5)
1. High voltage section
No.
(1)
(3)
Content
A
Transfer charger unit
B
Charger wire
(2)
A.Transfer charger unit
(3)
(1)
(2)
(3)
(2)
(3)
(1)
(1)
AR-5316 DISASSEMBLY AND ASSEMBLY 11-1
(4)
(2)
(3)
[11]DISASSEMBLY.fm 2 ページ
2005年7月1日 金曜日 午後5時29分
2.Optical section
C.Inverter PWB for copy lamp
(1)
Note: When disassembling or assembling the optical unit, be careful not
to touch the mirror and the reflector.
No.
Content
A
Table glass
B
Copy lamp unit
(2)
(1)
C
Inverter PWB for copy lamp
D
Copy lamp
E
Lens unit
F
Wire
A.Table glass
(1)
(2)
(1)
(3)
(1)
(4)
(1)
(3)
(3)
B.Copy lamp unit
Disassembly:
Assembly:
Adjustment:
Be sure to put No. 2/3 mirror unit to the positioning plate
(A).
Put the notched surface of wire holder (3) downward,
tighten temporarily, and install.
Main scanning direction distortion balance adjustment
(2)
D.Copy lamp
(4)
(4)
(2)
(2)
(3)
(1)
(2)
(A)
(1)
(3)
(A)
(1)
(3)
(2)
AR-5316 DISASSEMBLY AND ASSEMBLY 11-2
[11]DISASSEMBLY.fm 3 ページ
2005年7月1日 金曜日 午後5時29分
E.Lens unit
F.Wire
Note: Do not remove screws which are not indicated in the figure. If the
height of the base plate is changed, it cannot be adjusted in the
market.
Note: The CCD/lens unit is factory-adjusted before shipping.
Since these adjustments cannot be performed in the market.
Never touch the screws other than screw 2) of the CCD/lens unit.
(1)
(1)
(2)
(1)
(4)
(1)
(3)
(2)
(3)
(3)
(4)
(4)
(2)
Lens unit attachment
<1>Attach the lens unit so that the lens unit number on the
lens adjustment plate is aligned with the scribe line on the
base plate.
Lens unit number
( ) direction
Reference line (0)
(+) direction
One division: 1.4mm
CCD adjustment value
+4 scales
5.0~
+3 scales
3.6~4.9
+2 scales
2.2~3.5
+1 scale
0.8~2.1
Reference
-0.6~0.7
-1 scale
-2.0~ -0.7
-2 scales
-3.4~ -2.1
-3 scales
-4.8~ -3.5
-4 scales
~ -4.9
<2>Make a sample copy at the above position, and measure
the magnification ratio.
<3>Change the installing position in the horizontal direction to
adjust the magnification ratio.
•When the copy image is longer than the original, shift to
the positive (+) direction.
•When the copy image is shorter than the original, shift to
the negative (-) direction.
* 1 scale of the scribed line corresponds to 0.34% of
magnification ratio.
* If this adjustment is not satisfactory, make a fine adjustment
with SIM 48-2.
AR-5316 DISASSEMBLY AND ASSEMBLY 11-3
[11]DISASSEMBLY.fm 4 ページ
2005年7月1日 金曜日 午後5時29分
3.Fusing section
No.
C.Thermistor
Installation: When installing the thermistor, be sure to face the installing
projection (A) toward the installing surface.
Check that the thermistor is in contact with the upper heat
roller.
Contents
A
Fusing unit
B
Thermostat
C
Thermistor
D
Heater lamp
E
Upper heat roller
F
Separation pawl
G
Lower heat roller
H
Separation pawl
(1)
(A)
(2)
A.Fusing unit removal
(1)
(1)
D.Heater lamp
Assembly: Insert the spring (A) into the hole (B) in the fusing frame.
(3)
(2)
(A)
(B)
(2)
B.Thermostat
(1)
(2)
(1)
(2)
(2)
(3)
Assembly: Put the paper guide earth spring (A) under the paper guide
(B) before fusing.
(A)
(B)
(1)
(2)
(1)
AR-5316 DISASSEMBLY AND ASSEMBLY 11-4
[11]DISASSEMBLY.fm 5 ページ
2005年7月1日 金曜日 午後5時29分
(2)
(1)
Floil(GU2)
Grease(JFE552)
(1)
(4)
(3)
(1)
(2)
(A)
(B)
F.Separation pawl
(C)
(1)
Assembly: Put the fusing harness (A) on the heater lamp (B) as shown
in the figure and fix them together.<R>Place the fusing
harness inside the rib (C).
(2)
(3)
E.Upper heat roller
Disassembly:
There are three pawls on the fusing cover. Remove the
screws and slide the fusing cover to the right to remove.
The heater lamp is fixed on the fusing cover with a
screw. Slide the fusing cover to the front and remove the
screw, then remove the heater lamp.
(2)
(3)
(2)
(1)
(1)
(3)
(2)
(3)
(2)
(3)
(1)
(2)
AR-5316 DISASSEMBLY AND ASSEMBLY 11-5
[11]DISASSEMBLY.fm 6 ページ
2005年7月1日 金曜日 午後5時29分
4.Paper exit section
G.Lower heat roller
Assembly:
When installing the paper guide (3) before fusing, fix the
paper guide fixing plate with screws temporarily so that the
paper guide fixing plate (2) is in contact with the frame
bottom under fusing (A). Set the paper guide (3) before
fusing to the bottom line of the positioning reference (B),
and tighten the screw firmly.
Grease(JFE552)
No.
A
Content
Ozone filter
B
Cooling fan
C
Paper exit unit
D
Paper exit sensor
E
Transport roller
F
Paper exit roller
G
Paper exit interface P.W.B.
A.Ozone filter
(4)
(1)
(3)
(1)
(2)
(1)
(1)
(2)
(B)
(B)
(1)
(1)
(2)
(A)
(1)
H.Separation pawl
(2)
(1)
(2)
B.Cooling fan
(1)
(2)
(1)
(3)
(2)
(2)
(2)
(3)
AR-5316 DISASSEMBLY AND ASSEMBLY 11-6
[11]DISASSEMBLY.fm 7 ページ
2005年7月1日 金曜日 午後5時29分
C.Paper exit unit
D.Paper exit sensor
(2)
(A)Exit sensor
(2)
(2)
(A)
(2)
(4)
(3)
(1)
E.Transport roller
(1)
(1)
(2)
(1)
(3)
(2)
(3)
(5)
(2)
(1)
(4)
(3)
(1)
(2)
(3)
(3)
(3)
(5)
(4)
(6)
(2)
(4)
(1)
(5)
(1)
(1)
AR-5316 DISASSEMBLY AND ASSEMBLY 11-7
[11]DISASSEMBLY.fm 8 ページ
2005年7月1日 金曜日 午後5時29分
5.MCU
F.Paper exit roller
Assembly:
Insert the spring pin so that the waveform (A) of the spring
pin faces in the longitudinal direction of the paper exit
drive gear long hole (B).<R>Be sure to insert two ribs (C)
into the groove (D).
No.
A
Content
MCU disassembly
A.MCU disassembly
Note: When replacing the MCU PWB, be sure to replace the EEPROM of
the MCU PWB to be replaced.
(A)
(B)
(D)
(1)
(1)
(2)
(1)
(1)
(C)
(2)
(C)
(1)
(2)
(1)
(3)
(2)
(1)
(1)
(1)
(2)
(2)
(1)
(1)
(1)
Note: When replacing the MCU PWB, be sure to restore the original
jumper conditions.
(2)
(3)
6.Optical frame unit
No.
A
G.Paper exit interface P.W.B.
Content
Optical frame unit
A.Optical frame unit
(2)
Installation:
Install the optical unit in the sequence shown above.
(3)
(2)
(2)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(2)
(3)
(1)
(2)
AR-5316 DISASSEMBLY AND ASSEMBLY 11-8
(1)
[11]DISASSEMBLY.fm 9 ページ
2005年7月1日 金曜日 午後5時29分
7. LSU
No.
A
8. Tray paper feed section/Paper transport
section
Content
LSU unit
No.
A. LSU unit
(4)
Content
A
Middle frame unit
B
Drive unit
C
Solenoid (paper feed solenoid,, resist roller solenoid)
D
Resist roller clutch / Resist roller
E
Paper feed clutch/Paper feed roller (Semi-circular roller)
A. Middle frame unit
(2)
(1)
(3)
(2)
(3)
(1)
(1)
(1)
(2)
(1)
(1)
(2)
Assembly:
Do not miss the door lock pawl.
(1)
(1)
(1)
Note: Do not disassemble the LSU.
Note: When replacing the LSU, be careful not to touch the dust-shield
glass.
Adjustment:
•Image lead edge position adjustment
•Image left edge position adjustment
•Paper off-center adjustment
•Size of the screwdriver for removing the LSU
More than 50mm
Less than 120mm
AR-5316 DISASSEMBLY AND ASSEMBLY 11-9
(2)
[11]DISASSEMBLY.fm 10 ページ
2005年7月1日 金曜日 午後5時29分
B.Drive unit
Assembly:
D. Resist roller clutch/Resist roller
Move down the clutch pawl as shown below, and avoid the
clutch and install.
(1)
(1)
(2)
(2)
(3)
(3)
(3)
(4)
E. Paper feed clutch/Paper feed roller
(Semi-circular roller)
Moricote X56020
(1)
(2)
Grease G-484
C. Solenoid
(paper feed solenoid, resist roller solenoid)
(3)
(2)
(2)
(1)
AR-5316 DISASSEMBLY AND ASSEMBLY 11-10
[11]DISASSEMBLY.fm 11 ページ
2005年7月1日 金曜日 午後5時29分
9.Manual multi paper feed section
No.
A
B. Manual multi paper feed
Content
Manual transport roller/Manual paper feed roller
B
Manual multi paper feed
C
Manual feed solenoid
D
Manual transport clutch
E
Pressure plate unit
F
Manual paper feed clutch
(1)
(3)
A.Manual transport roller/Manual paper feed roller
Note: Push the lever at the right edge of the multi frame cover to the right
upper side and remove it.
(4)
(2)
A
(5)
(2)
A
A
A
A
(3) (4)
A
(1)
C. Manual feed solenoid
(2)
(5)
(1)
(B)
(2)
(3)
(4)
(2)
(2)
(3)
(5)
(1)
RI GI
(7)
N
O
(4)
(6)
Installation: Be careful of the installing direction of the manual transport
roller (6)
AR-5316 DISASSEMBLY AND ASSEMBLY 11-11
(A)
[11]DISASSEMBLY.fm 12 ページ
2005年7月1日 金曜日 午後5時29分
D. Manual transport clutch
F. Manual paper feed clutch
Note: Push the lever at the right edge of the multi frame cover to the
right upper side and remove it.
(1)
(2)
(1)
(2)
A
A
(5)
(3)
A
(1)
(4)
(1)
(3)
E.Pressure plate unit
(2)
(2)
(2)
(2)
(3)
(2)
(1)
(3)
(1)
(4)
(2)
(3)
(1)
AR-5316 DISASSEMBLY AND ASSEMBLY 11-12
[11]DISASSEMBLY.fm 13 ページ
2005年7月1日 金曜日 午後5時29分
10.Power section
C. High voltage P.W.B.
No.
(1)
Content
A
Power unit
B
Power fan
C
High voltage P.W.B.
D
Power P.W.B.
E
Power switch
(2)
(1)
A.Power unit
(1)
(1)
D. Power P.W.B.
(1)
(2)
(1)
(1)
(2)
(1)
(2)
(1)
(1)
(2)
(2)
(2)
(3)
(2)
(2)
(2)
(3)
(2)
(1)
(2)
(2)
(1)
(1)
E. Power switch
B. Power fan
(1)
(3)
(1)
(2)
(1)
(1)
(2)
AR-5316 DISASSEMBLY AND ASSEMBLY 11-13
[11]DISASSEMBLY.fm 14 ページ
2005年7月1日 金曜日 午後5時29分
11.Developing section
No.
C.MG roller
Contents
A
Developing box
B
Developing doctor
C
MG roller
A.Developing box
(2)
(1)
# " B.Developing doctor
! ! Adjustment:
Developing doctor gap adjustment
$ Adjustment:
MG roller main pole position adjustment
Note: Attach it to fit with the attachment reference when replacing the DV
blade.
AR-5316 DISASSEMBLY AND ASSEMBLY 11-14
[11]DISASSEMBLY.fm 15 ページ
2005年7月1日 金曜日 午後5時29分
12.Process section
13.Others
No.
A
Contents
No.
Drum unit
A
Contents
Operation P.W.B.
B
Main charger unit
B
Tray interface P.W.B.
C
Cleaning blade
C
Main motor
D
I/F P.W.B.
E
Paper entry sensor
A.Drum unit
F
Paper empty sensor
G
Paper feed roller
A. Operation P.W.B.
LO C K
(1)
(2)
(1)
B. Main charger unit
(1)
(5)
(2)
(1)
(6)
(5)
(5)
(7)
(5)
(5)
(4)
(3)
C.Cleaning blade
(1)
(1)
(2)
(1)
(1)
AR-5316 DISASSEMBLY AND ASSEMBLY 11-15
(2)
[11]DISASSEMBLY.fm 16 ページ
2005年7月1日 金曜日 午後5時29分
C. Main motor
(1)
(1)
(2)
(1)
(2)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(3)
(2)
(2)
D. I/F P.W.B.
(2)
B. Tray interface P.W.B.
(2)
(3)
(2)
(1)
(1)
(2)
(1)
(2)
(2)
(1)
(2)
(3)
(1)
AR-5316 DISASSEMBLY AND ASSEMBLY 11-16
[11]DISASSEMBLY.fm 17 ページ
2005年7月1日 金曜日 午後5時29分
E. Paper entry sensor
G. Paper feed roller
(1)
(1)
(2)
(1)
*
(2)
(3)
When removing the paper feed roller, operate the paper feed clutch
with SIM 6-1, and keep the paper feed roller down as shown in the
figure above for operation.
F. Paper empty sensor
(3)
(2)
(1)
AR-5316 DISASSEMBLY AND ASSEMBLY 11-17
[12]FLASHROM.fm
1 ページ 2005年7月1日 金曜日 午後5時31分
[12]FLASH ROM VERSION UP PROCEDURE
1.Preparation
3) PC side:
Boot the maintenance program. Select the model icon.
Write the download data (the file with the extension dwl) to the main body
of AR-5316.
Necessary files for download
• Maintenance.exe (Maintenance software)
• ProcPegasus.mdl
• ProcPegasus.ini
• ProcPegasus.fmt
• Pegasus.inf
• Usbscan.sys
• Download file:***.dwl
<Note>
•The Download file(***.dwl ) and the like that are to be downloaded
should be copied, in advance, into folders that have a maintenance
program.
•When creating a folder for a maintenance tool in the PC, be sure that no
lengthy folder name is included in the path.
(Example)
Incorrect c:\Maintenance Download Tool
Correct c:\Maintenance\Downtool
<Sample display>
4) PC side:
Confirm that the "Simulation Command List" tree is displayed on the
maintenance program.
5) PC side:
When the message "the main body has not got started running" is
displayed on the lowest area of the figure below after the
"maintenance program" is started up, select the "File" and then
"Reconnect" in the menu bar.
2.Download procedure
1) Main body side:
Executable by performing the Service Simulation No. 49-01 (Flash
Rom program-writing mode).
(A word "d" appears on the operation panel to denote the download
mode status. )
2) Connect the PC and the main body with the download cable
(USB cable).
(Be sure to use a USB cable for connection. USB2.0 of the AR-EB7
is not applicable.)
6) PC side:
Confirm a tree is displayed under the "Special (MCU/IMC2/FAX)" on
the maintenance program". (If no tree is displayed, confirm that the
USB is connected and select the "Reconnect" (the above 5) again.)
AR-5316 FLASH ROM VERSION UP PROCEDURE 12-1
[12]FLASHROM.fm
2 ページ 2005年7月1日 金曜日 午後5時31分
7) PC side:
Double click "Special (MCU/MCU2/FAX)" in the main tree item to
develop the sub tree items, and double click "DWL Download" in the
sub tree items.
12) After-process: Terminate the maintenance program, and turn on the
power of the main body.
After the download (data transmission) has been completed, exit the
software program. The USB cable can be removed at this point.
NOTE:
•For making a second connection with another machine, select the "File"
and "Reconnect" in the menu bar on the maintenance program at the
time of the USB being re-connected. Repeat the previous procedures
from the above 5).
8) PC side:
Specify the download file (*.dwl).
* Forbidden actions while downloading (Important)
Failure in the download concerned may not allow you to conduct the
subsequent download procedures. Added care should be taken to avoid
having the situation below arise while downloading.
•Switching off the main body of AR-5316.
•Disconnecting the download cable (USB cable).
9) PC side:
The download file is specified, download is automatically performed.
The "Automatic paper selection" lamp and "Start" lamp will blink
approximately 15 seconds after the download file is specified.
10) PC side:
When the message below is displayed, download is completed.
Completion message: DOWNLOAD COMPLETED
* If the above inhibit item occurs during downloading:
Turn OFF and ON the power.
1) If "d" (which means downloading) is displayed on the operation
panel LED of the machine, perform downloading again.
2) If "d" (which means downloading) is not displayed on the operation
panel LED of the machine, turn OFF the power, and press and hold
the ZOOM(%) key and the AUDIT CLEAR key and turn ON the
power. If, then, "d" (which means downloading) is displayed on the
operation panel LED of the machine, perform downloading again.
If "d" is still not displayed, the MCU must be replaced.
3. Installation procedure
A. USB joint maintenance program installation
The driver is installed by plug and play.
B. Installation procedure on Windows XP
NOTE (Important):
•Be sure that the power is not turned off and the USB cable is not
removed until the word "OFF" appears.
11) Main body side:
Wait until the word "OFF" appears on the operation panel.
The appearance of "OFF" indicates the completion of the download
(writing into ROM).
Turn the power off.
1) Machine side:
Executable by performing the Service Simulation No. 49-01 (Flash
Rom program-writing mode).
(A word "d" appears on the operation panel to denote the download
mode status. )
2) Connect the machine and the PC with a USB cable.
(Be sure to use a USB cable for connection. USB2.0 of the AR-EB7
is not applicable.)
AR-5316 FLASH ROM VERSION UP PROCEDURE 12-2
[12]FLASHROM.fm
3 ページ 2005年7月1日 金曜日 午後5時31分
3) Check that the following display is shown.
Select "Install from a list or the specific location" and press the NEXT
button.
6) Check that the path to the folder which includes the maintenance tool
driver (Pegasus.inf) is shown, and press the NEXT button.
7)) Check that the following display is shown. Press the Continue Anyway
button.
4) Select "Include this location in the serch". If the retrieval area does
not include the folder which includes the maintenance tool driver
(Pegasus.inf), select "Browse"
If the folder path is properly shown, press the NEXT button to go to
procedure 7).
8) When installation is completed, the following display is shown.
Press the Finish button.
5) Select the folder which includes the maintenance tool driver
(Pegasus.inf), and press the OK button.
(When the driver is included in the "C:\Pegasus" folder:)
The installation procedure (on Windows XP) is completed with the above
operation.
C. Installation procedure on Windows 2000
1) Machine side:
Executable by performing the Service Simulation No. 49-01 (Flash
Rom program-writing mode).
(A word "d" appears on the operation panel to denote the download
mode status. )
2) Connect the machine and the PC with a USB cable.
(Be sure to use a USB cable for connection. USB2.0 of the AR-EB7
is not applicable.)
AR-5316 FLASH ROM VERSION UP PROCEDURE 12-3
[12]FLASHROM.fm
4 ページ 2005年7月1日 金曜日 午後5時31分
3) Check that the new hardware search wizard is shown. Press the
NEXT button.
7) Specify the folder which includes the maintenance tool driver
(Pegasus.inf), and press the OPEN button.
Check that the path to the folder which includes the maintenance tool
driver (Pegasus.inf) is properly displayed, and press the OK button.
(When the maintenance tool driver is included in the folder of
"D:\Pegasus")
4) Select "Serch for a suitable driver for my device" and press the NEXT
button.
8) Press the NEXT button, and installation is started.
5) Select "Specify a location" and press the NEXT button.
9) When installation is completed, the following display is shown.
Press the Finish button.
6) Press the "Browse" button. Specify the folder which includes the
maintenance tool driver (Pegasus.inf)
The installation procedure of the joint maintenance program on Windows
2000 is completed with the above operation.
AR-5316 FLASH ROM VERSION UP PROCEDURE 12-4
AR-5316 ELECTRICAL SECTION 13-1
LVC1284
CPU INTERRUPT
SPPD
CPU I/O
RTH DRST
Other Inputs
MCU-PWB
SDRAM
Simp 16Mbyte
16bit
s
AD
Driver
HC151
3.3V
Mirror Motor
Driver
(296pin)
Zebra2 ASIC
5V,3.3V
LSU
D[15...0]
A[19...1]
Reset IC
3.3V
MHPS
HOME
POSITION
SENSOR
SPF
Polygon
Motor
4Kbyte
EEPROM
CRUM
I2C Bus
FAN
/POFF,HL,PR
FW
3.3V,5VEN,5V,24V
POWER SUPPLY
TC,GRID,MC,
BIAS
HVU
/CV_COPY
/CV_COUNT, /CV_START, /CV_C
A,
/CV_DPX, /CV_SIZE0, 1, 2, 3
LED
START KEY
HC151
5V
LC7935AN
5V
OPU PWB
KEY
LED
7seg LED
CASSETTE
Feed SOL , Pick up SOL
CASSETTE DETECTION,
PAPER DETECTION,
PAPER PASS DETECTION,
DOOR DETECTION
Light only
COIN VENDOR/AUDITOR
SELIN1,2,3
KIN1
SCAN1-6
PSW
PSL,ONL
FSOL
PSOL
Y1
SELIN1,2,3
UART
SPMT0/1/2/3
OP-CLK
OP-LATCH
OP-DATA
OP-BEO
Selector
Sensor
Driver
Driver
CPU CLK(19.6608MHz)
SSCG
PMCLK(2078.74(Hz))
8Mbit
CPU
H8S/2320
(19.6608MHz)
Software Reset
L1,2
W0,1,2,3
/SPFCOVER,
PAPER,
SPFOPEN,
/SPFOUT
SPFCLH,
SPFGSOL
SPFPSOL,
SPFRSOL
SPF
MOTOR
1Mb(1Mb*1)
SRAM
Flash ROM
CLON
LCX16374
24V
Lamp
Inverter
CCFL
/VIDEO
S/H
APCSTT
/SYNC
PWM
8bits(MSB/LSB)
ADCCLK,SYNCH,
BSAMP,VSAMP
SDI,SCLK,LOAD,OBE
MODE
LVTTL
M
P
X
3.3V
Main Motor Toner Motor
Scanner CLK(48MHz)
Printer CLK(20.3094MHz)
USB I/F
IEEE 1284 I/F
MPFS,RRS,
SGS,SRRC,SPUS,SPPS,
VFMCNT,VFM,MPFS,CPFS2,
CPFS1
Other Loads
U
PDIUSBP11AD
S
B
1
.
1 RIC
Download
I/F PWB
I
E
E
E
1
2
8
4
CCD Driver
/MMD
5V
CCD
(TCD1710)
B/W AFE(AD9826)
A
C
G
D
C
S
/MMRDY
A5V
TM+,TM-
5V
MM_AI0/AI1/PH_A
MM_BI0/BI1/PH_B
CCD PWB
PMD
Scanner Unit
[13]ELECTRICALSECTION.fm 1 ページ 2005年7月1日 金曜日 午後5時33分
[13] ELECTRICAL SECTION
1. Block diagram
*
GP1S58(O)
13FE-BT-VK-N
(WHITE)
AR-5316 ELECTRICAL SECTION 13-2
CRU
DEV UN
MAIN
TONER
MOTOR MOTOR
FFC
HAND PAPER PICK
UP SOLENOID
B3B-PH-K-S
(WHITE)
B4B-PH-K-S B4B-PH-K-BL
(BLACK)
(WHITE)
B2P-VH
(WHITE)
PAPER IN
SENSOR
PS SOL
Side Cover SW
CASETTE EMPTY
SENSOR
HAND PAPER EMPTY
SENSOR
Front Cover SW
CASETTE SWITCH
SENSOR
PICK UP SOL
(RED)
B26B-PHDSS-B
(WHITE)
B12B-PHDSS-B
(WHITE)
CASETTE
B4B-PH-K-R
(RED)
B3B-PH-K-R
(RED)
B2B-XH-A-R
B4B-PH-K-S
(WHITE)
B3B-PH-K-S
(WHITE)
B3B-PH-K-BK
B3P-VH
(BLACK)
(WHITE)
35FE-BT-VK-N
(WHITE)
B3B-PH-K-R
(RED)
B2B-XH-A-BK
(BLACK)
B2B-XH-A-S
(WHITE)
B20B-PHDSS-B
(WHITE)
MCU-PWB
FE4-32-S1505
(BLACK)
SUB-D 25
GP1S58(C)
Mirror HP
SENSOR
FFC
I/F
MC
REACTOL
230V ONLY
BC
TC
3P TERMINAL
230V ONLY
COOLING FUN
B4B-PH-K-S B3B-PH-K-S
(WHITE)
(WHITE)
MCFB
IEEE1284
USB1.1
BD-PWB
B03P-VL
(WHITE)
AC Cord
POLYGON
MOTOR
APC-PWB
GRID
AC SW
POWER PWB
Bias
HVU
B7B-PH-K-S
(RED)
HEATER LAMP
THERMISTER
08FE-BT-VK-N
(WHITE)
B3B-PH-K-BK
(BLACK)
FUSER
B6B-PH-K-S
(WHITE)
DRUM INISAL SW
B3B-PH-K-SX
2
(WHITE)
MODEL W/O SHIFTER
DUP
SENSOR
24FMN-BTRK-A
(BLACK)
COOLING
FAN
Option
13FE-BT-VK-N
(WHITE)
PAPER OUT
SENSOR
B4B-PH-K-S
(WHITE)
04FE-BT-VK-N
(WHITE)
SPF GROUND WIRE
ORIGINAL TRAY HARNESS
SENSOR HARNESS
SPF UN
CCD PWB
FFC
COOLING
FAN
3
COPY LAMP
LSU
35FE-BT-VK-N
(WHITE)
MODEL WITH SHIFTER
FFC
FFC
Mirror MOTOR
OPTICAL BASE PLATE
FFC
COOLING
FAN
COOLING
FAN
SHIFTER HP
SENSOR
GP1A71A1(O)
IMSA-9610S24C
(BLACK)
SHIFTER
MOTOR
COPY OP PWB
OPERETION PANEL
(O) Normal Open :Low
(C) Normal Close :High
[13]ELECTRICALSECTION.fm 2 ページ 2005年7月1日 金曜日 午後5時33分
3. Actual wiring diagram
ACTUAL WIRING DIAGRAM 1/7
B18B-PHDSS-B
(WHITE)
[14]LeadFree.fm
1 ページ 2005年7月1日 金曜日 午後5時33分
LEAD-FREE SOLDER
The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder.
The alphabet following the LF mark shows the kind of lead-free solder.
Example:
<Solder composition code of lead-free solder>
Lead-Free
5mm
Solder composition
code (Refer to the
table at the right.)
a
Solder composition
Solder composition code
Sn-Ag-Cu
a
Sn-Ag-Bi
Sn-Ag-Bi-Cu
b
Sn-Zn-Bi
z
Sn-In-Ag-Bi
i
Sn-Cu-Ni
n
Sn-Ag-Sb
s
Bi-Sn-Ag-P
Bi-Sn-Ag
p
(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD
When repairing a lead-free solder PWB, use lead-free solder thread.
Never use conventional lead solder thread, which may cause a breakdown or an accident.
Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclusive-use
soldering iron is recommendable.
(2) NOTE FOR SOLDERING WORK
Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering capacity is
inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land separation or may exceed
the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB when completion of soldering is
confirmed.
Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.
If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip after
completion of soldering work.
If the soldering iron tip is discolored black during soldering work, clean and file the tip with steel wool or a fine filer.
[00]COVER.fm 2 ページ
2005年7月1日 金曜日 午後5時36分
COPYRIGHT c 2005 BY SHARP CORPORATION
All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted,
in any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise,
without prior written permission of the publisher.
Trademark acknowledgments
Windows and Windows NT are trademarks of Microsoft Corporation in the U.S.A.
and other countries.
IBM and PC/AT are trademarks of International Business Machines Corporation.
PCL is a trademark of Hewlett-Packard Company.
Pentium is a registered trademark of Intel Corporation.
All other trademarks and copyrights are the property of their respective owners.
SHARP CORPORATION
Digital Document System Group
Products Quality Assurance Department
Yamatokoriyama, Nara 639-1186, Japan
2005 July Printed in Japan N