CBL108-User Manual

User Manual

Main Features:

1.

100% keyboard with QWERTY layout (108 Keys)

2.

Cherry MX key switch (Black, Blue, Brown, Red)

3.

Double layer PCB

4.

Key cap material: Double Shot PBT

5.

LED backlight

6. USB Interface

Package Material:

1. Keyboard x 1

2. User Manual x 1

Technical Specification

Number of keys :

US ASCII (108 Keys) = US Layout

Dimension :

44.1 x 13.8 x 4.3cm (Keyboard)

Cable :

1.8 meters

Key switch life time :

Cherry: >50 million actuations

Package :

20 keyboards / 1 outer box

Interface :

USB (DC5V ----500mA)

Available layout:

US USA

Programming Instruction

1.

Press PMode(Fn + Pn) to enter the programming mode (Pn LED flashing)

2.

Press the key you want to program (Pn LED on)

3.

Key in the programming content and then press Pn (Pn LED flashing again)

4. Repeat step 2 and step 3 to program other keys

5. Press PMode(Fn + Pn) to exit programming mode (Pn LED off)

Note:

• Under SELECT state (step 1), you can press Pn + any key to view its content in a word processing software (e.g., Notepad)

•

Support time delay, press 15ms key(Fn + Ins) each time to delay 15ms, press 0.1s key(Fn + Home) each time to delay 0.1s, press 0.5s key(Fn + PgUp) each time to delay 0.5s. Consecutive delay will add up but will only be counted as 1 key stroke

• Every key can program up to 64 key strokes

• Repeat step 2 and step 3 to program other keys

• If there is no key pressed for 15 sec in programming mode, it will exit to normal mode

Programming Usage

Press Pn + Programmed key, OR

Press Toggle (Two arrows key) to light up the Toggle LED first. Then press the programmed key directly. If you press Pn + Programmed key at this moment, it will output the original key code.

Programming Examples

1.

Program A as 123: Fn + Pn, A, 1, 2, 3, Pn

2.

Continue to program B as Ctrl + C: B, Ctrl(Not release), C, Release Ctrl and C, Pn

3.

Continue to program C to run CMD under WIN7: Win, C, Fn + Home, M, Fn + Home, D, Fn + PgUp,

Enter, Pn

4.

Finish programming: Fn + Pn

5.

Invoking programmed A: Pn + A => Output 123

6.

Invoking programmed C: Pn + C => Running CMD.EXE

7.

Switch to Pn layer: Toggle(Two arrows key) => Toggle LED on

(1) Invoking programmed B: B => Output Ctrl + C (Same as copy)

(2) Invoking programmed C: C=> Running CMD.EXE

(3) If you need to get the A back (Now pressing A is 123): Pn + A => A

Rollover Mode Switch

Press Nkey (Lightning key), the Nkey LED will be flashing till stop. It means the keyboard is switching the rollover mode. Nkey LED is on for N-key rollover mode. Nkey LED is off for 6-key rollover mode.

Backlight Mode Switch

Press Fn + Nkey (Lightning key) to circulate different backlight modes: Individual Dimming → Laser Sidetrack →

Ripple Explosion → Breathing → All LED off → All LED on. Under All LED on mode, you can press Fn + ↑ and Fn

+ ↑ to adjust brightness. There are 7 levels of brightness.

Restore to factory default

Press and hold Fn + R, Toggle LED is flashing after 3 sec. Continue to hold Fn + R until the Toggle LED flashes for 9 times will restore to factory default

Fn +

Pn

Rollover

↑

↓

Ins

Home

PgUp

F5

F6

F7

F8

F1

F2

F3

F4

Fn General keys

=

Mute

Volume Down

Volume Up

Play/Pause

Previous Track

Next Track

Calculator

Lock Win key

Enter/Exit Programming Mode

Switch Backlight Mode

Increase Brightness

Decrease Britghtness

Delay 15ms

Delay 0.1s

Delay 0.5s

Remark

Key code change

Only valid in programming mode