ECOR960-16X1 - User manual

Add to my manuals
149 Pages

advertisement

ECOR960-16X1 - User manual | Manualzz
ECOR960 X1
16CH, H.264, 960H
User’s Manual
Copyright © EverFocus Electronics Corp,
Release Date: June, 2013
Notice: This content is subject to be changed without notice.
EVERFOCUS ELEC TRONICS CORPORATION
ECOR960 X1
User’s Manual
 2013 EverFocus Electronics Corp
www.everfocus.com
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form
or by any means without written permission of the Everfocus Electronics Corporation.
Release Date: June, 2013
QuickTime is a registered trademark of the Apple Computer, Inc.
Windows is a registered trademark of the Microsoft Corporation.
Linksys is a registered trademark of the Linksys Corporation.
D-Link is a registered trademark of the D-Link Corporation.
DynDNS is a registered trademark of the DynDNS.org Corporation.
Other product and company names mentioned herein may be the trademarks of their respective owners.
Safety Precautions
 Refer all work related to the installation of this product to qualified service personnel or
system installers.
 Do not block the ventilation openings or slots on the cover.
 Do not drop metallic parts through slots. This could permanently damage the appliance.
Turn the power off immediately and contact qualified service personnel for service.
 Do not attempt to disassemble the appliance. To prevent electric shock, do not remove
screws or covers. There are no user-serviceable parts inside. Contact qualified service
personnel for maintenance. Handle the appliance with care. Do not strike or shake, as this
may damage the appliance.
 Do not expose the appliance to water or moisture, nor try to operate it in wet areas. Do
take immediate action if the appliance becomes wet. Turn the power off and refer servicing
to qualified service personnel. Moisture may damage the appliance and also may cause
electric shock.
 Do not use strong or abrasive detergents when cleaning the appliance body. Use a dry cloth
to clean the appliance when it is dirty. When the dirt is hard to remove, use a mild
detergent and wipe gently.
 Do not overload outlets and extension cords as this may result in a risk of fire or electric
shock.
 Do not operate the appliance beyond its specified temperature, humidity or power source
ratings. Do not use the appliance in an extreme environment where high temperature or
high humidity exists. Use the DVR at temperatures within 0°C~40°C / 32°F~104°F (Storage).
The input power source is 12 VDC / 60W.

Read Instructions
All the safety and operating instructions should be read before the unit is operated.

Retain Instructions
The safety and operating instructions should be retained for future reference.

Heed Warnings
All warnings on the unit and in the operating instructions should be adhered to.
ii

Follow Instructions
All operating and use instructions should be followed.

Cleaning
Unplug the unit from the outlet before cleaning. Do not use liquid cleaners, abrasive or
aerosol cleaners. Use a damp cloth for cleaning

Attachments
Do not use attachments not recommended by the product manufacturer as they may
cause hazards.

Water and Moisture
Do not use this unit near water-for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub, in a wet basement, near a swimming pool, in an unprotected outdoor
installation, or any area which is classified as a wet location.

Servicing
Do not attempt to service this unit by yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.

Power Cord Protection
Power supply cords should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them, playing particular attention to cords and plugs,
convenience receptacles, and the point where they exit from the appliance.

Object and Liquid Entry
Never push objects of any kind into this unit through openings as they may touch
dangerous voltage points or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the unit.

Battery
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
a. Use only two AAA dry cell batteries.
b. Do not dispose of the batteries in a fire as it may explode.
ATTENTION! This is a class A product which may cause radio interference in a
domestic environment; in this case, the user may be urged to take adequate measures.
iii
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the users’ authority to operate this equipment.
This Product is RoHS compliant.
WEEE
Your EverFocus product is designed and manufactured with high quality materials and
components which can be recycled and reused. This symbol means that electrical and
electronic equipment, at their end-of-life, should be disposed of separately from your
household waste. Please, dispose of this equipment at your local community waste
collection/recycling centre. In the European Union there are separate collection systems
for used electrical and electronic product.
Please, help us to conserve the environment we live in!
This product complies with the High-Definition Multimedia Interface (HDMI)
Specification Adopter Agreement.
The information in this manual was current upon publication. The manufacturer reserves the right
to revise and improve his products. Therefore, all specifications are subject to change without prior
notice. Manufacturer is not responsible for misprints or typographical errors.
Please read this manual carefully before installing and using this unit. Be sure to keep it handy for
later reference.
iv
TABLE OF CONTENTS
1.
Introduction ........................................................................................................................1
1.1
1.2
1.3
1.4
2.
Features .....................................................................................................................3
Packing List.................................................................................................................4
Front Panel .................................................................................................................5
Rear Panel ..................................................................................................................7
Installation ..........................................................................................................................8
2.1 Hard Disk Installation .................................................................................................8
2.1.1 Hard Disk Compatibility List...........................................................................11
2.2 Rack Mount ..............................................................................................................11
2.3 Basic Connection ......................................................................................................12
2.3.1 Monitor Connection ......................................................................................13
2.3.2 Alarm I/O ......................................................................................................14
2.3.3 RS-485 Port ...................................................................................................15
2.4 Turning On / Off the Power ......................................................................................15
2.5 Checking the Dynamic Address ................................................................................16
2.6 Connecting the DVR to the Network ........................................................................19
2.6.1 Router or LAN Connection .............................................................................19
2.6.2 Direct High-Speed Connection ......................................................................22
2.6.3 One-to-One Connection ................................................................................23
3.
Mouse and Front Panel Button Operation........................................................................27
3.1 USB Mouse Operation ..............................................................................................27
3.1.1 How to Select a Channel /Enable Audio.........................................................27
3.1.2 OSD Root Menu ............................................................................................27
3.1.3 Field Input Options ........................................................................................28
3.2 Front Panel Buttons Operation .................................................................................29
3.2.1 Front Panel Review .......................................................................................29
3.2.2 How to Select a Channel / Enable Audio ........................................................29
3.2.3 OSD Root Menu ............................................................................................29
3.2.4 Field Input Options ........................................................................................30
3.3 General Operation ...................................................................................................31
3.3.1 Login .............................................................................................................31
3.3.2 Camera Selection ..........................................................................................32
3.3.3 Audio Selection .............................................................................................33
4.
OSD Root Menu ................................................................................................................34
4.1 PTZ ...........................................................................................................................36
v
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.
4.1.1 Express Control of PTZ...................................................................................38
Layout Switching ......................................................................................................39
Channel Switching ....................................................................................................39
Display .....................................................................................................................40
Sequence .................................................................................................................40
Monitor Switching ....................................................................................................41
Zoom........................................................................................................................41
Archiving the Recordings or Log Data to the USB or DVD .........................................43
Logout ......................................................................................................................44
4.9.1 Temporarily Logout .......................................................................................45
Playback............................................................................................................................46
5.1 Quick Playback .........................................................................................................46
5.2 Playback Bar .............................................................................................................47
5.3 Searching the Recordings for Playing Back ...............................................................49
5.3.1 Time Search ..................................................................................................50
5.3.2 Event Search .................................................................................................51
5.3.3 Smart Search .................................................................................................52
5.3.4 Snapshot Search............................................................................................54
6.
Configuration ....................................................................................................................56
6.1 Express.....................................................................................................................58
6.2 Camera Settings .......................................................................................................60
6.2.1 Basic Setting ..................................................................................................60
6.2.2 Video Adjust..................................................................................................62
6.2.3 Motion ..........................................................................................................63
6.2.4 Video Loss .....................................................................................................66
6.3 Record and Play .......................................................................................................68
6.3.1 Record ..........................................................................................................68
6.3.2 Built-in Calculator..........................................................................................69
6.3.3 Play ...............................................................................................................70
6.4 Alarm & Event ..........................................................................................................71
6.4.1 Alarm ............................................................................................................71
6.4.2 Event.............................................................................................................73
6.5 Schedule Setting ......................................................................................................80
6.5.1 Express Setup ................................................................................................80
6.5.2 Holidays ........................................................................................................81
6.5.3 Schedule .......................................................................................................82
6.5.4 Alarm Action .................................................................................................88
6.6 Network Settings......................................................................................................92
6.6.1 LAN ...............................................................................................................92
6.6.2 Email .............................................................................................................95
vi
6.7
6.8
6.9
6.10
7.
6.6.3 DDNS ............................................................................................................96
6.6.4 Alarm Server .................................................................................................98
6.6.5 Remote / Mobile ...........................................................................................99
6.6.6 Network Testing ............................................................................................99
Disk ........................................................................................................................100
6.7.1 Disk .............................................................................................................100
6.7.2 Lock/Format................................................................................................101
Display Setting .......................................................................................................102
6.8.1 Monitor OSD ...............................................................................................102
6.8.2 Main M/T SEQ .............................................................................................103
6.8.3 Call M/T SEQ ...............................................................................................103
System Setting .......................................................................................................104
6.9.1 Date / Time .................................................................................................104
6.9.2 Daylight Saving Time ...................................................................................105
6.9.3 User ............................................................................................................106
6.9.4 I/O Control ..................................................................................................108
6.9.5 Misc. ...........................................................................................................110
6.9.6 Quick Archive ..............................................................................................111
Information ..........................................................................................................112
6.10.1 System ......................................................................................................112
6.10.2 Log ............................................................................................................113
Remote Access to the DVR..............................................................................................114
7.1 Accessing the DVR on the Network ........................................................................114
7.2 Browser Security Setting ........................................................................................115
7.2.1 Installing ActiveX Controls ...........................................................................115
7.2.2 Enabling ActiveX Controls............................................................................118
7.3 Remote Live View...................................................................................................121
7.4 Menu Bar ...............................................................................................................122
7.5 Remote Playback....................................................................................................123
8.
Specifications ..................................................................................................................124
9.
Troubleshooting..............................................................................................................126
Appendix A: Network Overview .............................................................................................127
Appendix B: Linksys & D-Link Port Forwarding.......................................................................131
Appendix C: Timing of Alarm Modes ......................................................................................135
Appendix D: Express Setup Recording Value Selection Rules .................................................138
Appendix E: IR Remote Control ..............................................................................................140
vii
ECOR960 X1
Chapter
1.
1
Introduction
EverFocus brings you the next generation of analog recording. The new ECOR960 X1 digital video
recorder benefits users by digitizing the highest quality, state of the art 960H cameras for live and
remote monitoring, surveillance review, and archival. The ECOR960 X1 also supports (120FPS total)
recording over 16-channels at WD1 (960x480/960x576) resolution, providing the ability to capture
even fast moving objects at enhanced detail levels.
The ECOR960 X1 DVR also supports convenient video export operations to USB & DVD (Optional).
Its dual streams H.264 encoder provides users smooth remote viewing experience in low
bandwidth networks while simultaneously preserving a high quality recording in the DVR hard disk.
The ECOR960 X1 can provide clear 1080p Full HD Video output to both HDMI and VGA monitors
with an intuitive onscreen user interface for efficient operation. User can also easily operate the
machine using a USB mouse or via the front panel buttons.
When paired with our powerful EverFocus’ CMS, the ECOR960 X1 can be used in complex
multi-site installations, with centralized management. The ECOR960 X1 is also fully supported by
the EverFocus Mobile applications remote viewer on iOS and Android devices, which help extend
video surveillance from fix location to mobile environments.
960H is the highest resolution for analog CCTV, increasing resolution by 30% compared to D1.
With the better resolution benefited by 960H, the definition of video image will certainly be higher.
Moreover, the 960H CCD sensor performs greater image clarity in low-light environment than IP
and HD-SDI CMOS sensors. A 960H DVR, like our new ECOR960 X1 DVR, can support cameras with
resolution up to700TVL and you can use the existing coaxial infrastructure without the need of
re-cabling.
1
ECOR960 X1
IR Remote Control
DVD Burner
Internal 3.5" HDDs (Optional)
Mouse or USB Memory Stick
eSATA HDD Expansion
(EDA450)
Analog Camera 1~16
Alarm In /
Out
Main Monitor
Main Monitor
(HDMI)*
(VGA)*
Call Monitor
(BNC)
Network
Web Remote
Client
Line Level
Audio In 1~4 Line Level
Audio Out
RS-232
Data Input
Power Supply
Mouse or
USB Memory
Stick
PowerVideo Plus
(CMS)
RS-485 Device
Figure 1-1
*Both HDMI and VGA ports can be used as the Main monitor outputs at the same time.
2
ECOR960 X1
1.1 Features
•
16CH WD1 recording and playback
•
WD1 capability provides higher resolution (960x576 / 960x480) compared to D1
•
H.264 compression format for enhancing recording capacity and improving network image
transmission speed
•
Two Main Monitors: Both HDMI and VGA ports can be used as the Main monitor outputs at
the same time
•
Call Monitor: Sequenced view through composite BNC output with multiplex and sequencing
•
Free Everfocus DDNS Service – static IP address is not required for reliable remote access
•
Supports two SATA ports for internal HDDs
•
Supports one eSATA port for external HDD (EDA450)
•
Supports live monitoring and playback of video from mobile devices via Mobile applications
•
Multiple Control Inputs: Mouse / front panel / remote controller / EKB500 keyboard
•
Build-in record time calculator for fast recording estimation
•
Multiple intelligent video query functionality, including snapshot and smart search
•
Powerful archive functionality from both remote and DVR sites
•
Simplified access to common features such as setup, archival, playback and search functions
through OSD root menu
•
Remote configuration support from built-in web interface
•
One Gigabit Ethernet interface for remote network viewing and control
•
On-screen PTZ control via mouse, front panel, remote controller or EKB500 keyboard
•
Built-in DVD burner (Optional)
•
Dual USB 2.0 ports for video archive and mouse control
•
Integration with EverFocus’ CMS
•
Multi-language support
•
19” rack mountable – rack ears included
3
ECOR960 X1
1.2 Packing List
• DVR x 1
• Power Cord
• User’s Manual x 1
• Rack Ear x 2
• Mouse x 1
• Adaptor x 1
• Internal HDD Bracket x 2 (with 4 Rubber Spacers, 4 Black Long Screws and 8 Silver Screws)
(
)
• SATA Cable x 2 (for connecting the internal HDD) *Please see Note 3.
• IR Remote Control x 1 (with two AAA batteries) *Please see Note 4.
(
)
Note:
1. Equipment configurations and supplied accessories vary by country. Please consult your
local EverFocus office or agents for more information. Please also keep the shipping
carton for possible future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.
3. Two SATA cables will be supplied for DVRs without HDDs installed. If the order contains
HDD installation, the SATA cable will not be supplied.
4. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
a. Use only two AAA dry cell batteries.
b. Do not dispose of the batteries in a fire as it may explode.
4
ECOR960 X1
1.3 Front Panel
1
3
4
5
6
7
14
15
16
17
18
2
12
13
8
9
10
11
19 20
Figure 1-2
No. Name
1
IR Receiver
Description
Receiver for IR Remote Control.
Use the DVD+RW Burner for archiving the recordings from the DVR.
This function is optional for Germany.
Press to play the recorded data in fast reverse.
2
DVD+RW Burner
3
Fast Reverse
4
Reverse
Play/Pause
Press to play the recorded data in reverse at normal speed. Press this
button again to Pause the reverse playback. Press the Stop button to
stop all playback actions and exit the playback area.
5
Stop
Press to stop the Reverse, Fast Reverse, Play, or Fast Forward
functions, if that function is active. This button stops all Play functions,
but no Recording functions.
6
Play/Pause
Press to play the recorded data forward. Press this button again to
Pause the playback. Press the Stop button to stop all playback actions
and exit the playback area.
7
8
9
Fast Forward
Menu/Esc
Arrow Keys
Press to play the recorded data in fast forward.
Press to enter/exit the Main Setup Menu.
Use these arrow keys to change the Menu settings.
Enter
Use this button in conjunction with the Menu/Esc button (8) and the
Arrow Keys (9) to select menu values or to scroll between menu
categories. You can also use it in conjunction with a mouse or you can
use only a mouse to do these functions.
10
5
ECOR960 X1
No. Name
Description
Power LED: Indicates the power is on.
HDD LED: Indicates the internal Hard Disk is activating.
Alarm LED: Indicates the alarm input is triggered.
Network LED: Indicates the DVR is connected to the network.
Record LED: Indicates the DVR is recording.
11
Status LED
12
USB2.0 Port
The USB2.0 ports for connecting to a mouse or external storage
device.
13
Channel 1~16
Press to display the channel in full screen. The LED indicates the
channel is displayed in full screen.
14
View
15
SEQ (Sequence)
16
Display
17
Monitor
Press to switch between the Main and Call monitors. Just remember
to exit out of the setup menus before doing so.
18
Zoom
Press repeatedly to toggle between 2x and 4x zoom. Press the
Menu/Esc button to switch zoom off.
19
20
Search
Copy
Press to enter the Search Setup menu.
Press to enter the Copy Menu.
Press the type of layout you want for displaying your channel feeds.
Press to enter the automatic sequence mode. This will show each
channel feed in sequence.
Press to cycle between the info display types (channel and status bar
info).
6
ECOR960 X1
1.4 Rear Panel
2
1
5
6
7
8
9
10
11
12
4
3
13
14
Figure 1-3
No. Name
1
Video IN / OUT (Looping)
connectors
2
3
eSATA Port
Audio Input
4
Audio Output
5
6
7
8
9
10
Alarm Input
Alarm Output
Main Monitor Port (HDMI)
Main Monitor Port (VGA)
Call Monitor Port (BNC)
LAN
11
USB2.0 Port
12
RS-232 Port
13
RS-485 Port
14
Power Port
Description
Connect up to 16 cameras to the Video IN connectors
(bottom layer). You can also connect equipment like
monitors to the Video OUT connectors (top layer).
Connects to an external eSATA storage device.
Connects to the audio input devices.
Connects to the audio output devices, such as speakers.
Note that the speakers with amplifier are required.
Connects up to 16 alarm inputs.
Connects to 4 alarm output device.
Connects to the Main monitor using a HDMI cable.
Connects to the Main monitor using a VGA cable.
Connects to the Call monitor using a BNC cable.
Connects to the Network.
The USB2.0 ports for connecting to a mouse or external
storage device.
This port is currently reserved. Connects to the RS-232
device.
Connects to the RS-485 device, such as EverFocus’ EKB-500
keyboard.
Connects to the 12 VDC power using the supplied Power
Cord.
7
ECOR960 X1
Chapter
2
2.
Installation
2.1 Hard Disk Installation
1. Make sure the DVR is power-off.
2. Unscrew the three housing screws on the back panel of the DVR.
Figure 2-1
3. Unscrew the two housing screws on the both side of the DVR. Push the housing to the back
and open it.
Figure 2-2
4. Screw two HDD brackets on both sides of the HDDs using the Sliver Screws.
Sliver Screw
HDD Bracket
Figure 2-3
8
ECOR960 X1
5. Push the Rubber Spacer into the bottom slot of the Bracket.
Slot of HDD Bracket
Spacer
Figure 2-4
6. Insert the Black Long screws into the Rubber Spacers.
Black Long Screw
Spacer
Figure 2-5
7. Use the SATA Cable, and connect one end to the SATA port on the small PCB inside the DVR,
and the other end to the SATA port on the HDD.
Figure 2-6
9
ECOR960 X1
8. Connect the internal power cable to the HDD.
Figure 2-7
Note: The internal power cable is connected to the Main board inside the DVR. The power
cable features two connectors, which can be used to connect to two HDDs.
9. Screw the HDDs with brackets inside the DVR.
Figure 2-8
10. Screw back the housing to the DVR.
10
ECOR960 X1
2.1.1 Hard Disk Compatibility List
Please use the hard disk models recommended in the list below to ensure your hard disks will be
compatible.
SATA Hard Disk
Seagate
Western Digital
Model
SV35.5 SATA2 / ST3500410SV
SV35.5 SATA2 / ST31000525SV
SV35.5 SATA3 / ST3500411SV
SV35.5 SATA3 / ST31000526SV
SV35 SATA3 / ST2000VX002
Barracuda SATA3 / ST500DM002
Barracuda SATA3 / ST1000DM003
WD10EVDS SATA2
WD10EURS SATA2
WD20EVDS SATA2
WD20EURS SATA2
WD1600AVVS SATA
WD3200AVVS SATA
WD5000AVVS SATA
WD7500AVVS SATA
WD10EVVS SATA
Capacity
500GB
1TB
500GB
1TB
2TB
500GB
1TB
1TB
1TB
2TB
2TB
160GB
320GB
500GB
750GB
1TB
Note: If using two or more hard disks, please choose the hard disks with the same capacity.
2.2 Rack Mount
To install rack ears on the DVR:
1. Unscrew the four M3 (φ6.8) screws on both side of the DVR.
2. Use the supplied two rack ears and the above screws for rack mount installation on both side.
Figure 2-9
11
ECOR960 X1
2.3 Basic Connection
The instructions below describe the basic connection for the ECOR960 X1. For details on cable
connections, please refer to the following sections.
1
4
Mouse
2
3
Analog Camera 1~16
Line Level
Audio Out
Line Level Audio In 1~4
6
5
Network
Main Monitor
Main Monitor
(HDMI)*
(VGA)*
7
Power Supply
Call Monitor
(BNC)
Web Remote
Client
PowerVideo Plus
(CMS)
Figure 2-10
1. Optionally connect a mouse to the DVR to control the system. You can also control the
system using the supplied IR Remote Control or the control keys on the front panel.
2. Connect the cameras to the DVR using the coaxial cables. 700TVL cameras are recommended.
3. Connect the audio input devices to the DVR.
4. To listen to audio of video source, connect speakers to the Audio Out port. Note that
speakers with amplifier are required.
5. To view videos, connect a monitor to the HDMI, VGA or BNC port using the HDMI, VGA or
BNC cable supplied by the monitor manufacturer.
6. To manage the DVR over network, use a standard RJ-45 cable to connect the DVR to the
network.
7. Using the supplied Power Cord, connect one end to the 12 VDC port on the DVR and the
other end to the 12 VDC power outlet.
Note: Please ensure to connect the internal power cables to the internal HDDs before
powering on the DVR.
12
ECOR960 X1
2.3.1
Monitor Connection
Connect the monitor to the HDMI, VGA or BNC port on the rear panel of the DVR. The ECOR960
X1 DVR provides 2 main monitor outputs with identical functionality - VGA and HDMI.
Both outputs can be used simultaneously and deliver full HD output resolution (1920x1080,
progressive, 60 Hz. vert., 68 KHz hor.).
Make sure that the connected monitor's specifications comply with these resolution
requirements.
Rear View
HDMI Cable / VGA Cable
BNC Cable
Main Monitor
Call Monitor
Figure 2-11
Note:
1. The connected monitors’ specifications must comply with the resolution requirements.
2. Do not exceed the max. HDMI cable length of 15 meters.
3. The standard HDMI cables can support cable length up to 3 meters. For longer
distances, such as 15 meters, it is highly recommended to use high quality HDMI cables.
13
ECOR960 X1
2.3.2
Alarm I/O
The DVR provides four alarm inputs and two alarm outputs. Please refer to the table below
for PIN assignment.
Alarm in
Alarm out
Figure 2-12
Alarm Input
No.
1-16
G
Description
ALM_IN1 – ALM_IN16
GND
Alarm Input Contacts
This DVR provides one alarm input per camera. All inputs are programmable N.O. (Normal
Open) or N.C. (Normal Closed). All settings are programmed in the ALARM / Event menu.
ALMIN
ALMIN
GND
GND
Alarm Input with N.O. contact in idle state
Alarm Input with N.C. contact in idle state
Alarm Output Contacts
The relay output provides either Normally Open or Normally Closed dry contacts.
ALMOUT +
ALMOUT +
ALMOUT -
ALMOUT -
14
ECOR960 X1
2.3.3
RS-485 Port
The RS-485 port, located on the rear panel of the DVR, can be used to connect to an RS-485
keyboard, such as EverFocus’ EKB500, for controlling HD PTZ cameras. For details on the
RS-485 configurations on the DVR, please refer to 6.9.4 I/O Control.
Rear View
RS-485 Port
EKB500
RS-485
RJ-45 Cable
PTZ Camera 1~16
Connector Box
Figure 2-13
2.4 Turning On / Off the Power
Before powering on the DVR, please make sure the internal HDDs have been installed properly.
Once you have completed the basic cable connections, you are ready to turn on the DVR.
Simply connect the supplied Power Cord to the power outlet. All of the LED indicators on the
front panel will light up. The DVR will automatically run an internal process, when the process is
complete, the LED indicators will turn off, and the Power LED will remain light up in green. And
then you can start operating the DVR. To turn off the power, simply unplug the Power Cord from
the power outlet.
15
ECOR960 X1
2.5 Checking the Dynamic IP Address
You can look up the IP address and access the Web interface of the DVR using the IP Utility (IPU)
program, which can be downloaded from EverFocus’ Website: http://www.everfocus.com/tools.cfm.
Please connect the DVR in the same LAN of your computer.
1. Install and then start the IPU program
. The following dialog box appears.
Figure 2-14
2. IPU will automatically search the IP devices connected in the LAN. The default network values
of the IP devices will be displayed. By default, the network protocol of the IP device is DHCP.
3. To configure the network settings, select an IP device and then click Login/Multi Login.
Figure 2-15
16
ECOR960 X1
4. Type the user ID and password. Click OK.
Note:
1. The default user ID is admin and the default password is 11111111.
2. If you select more than one DVRs that have the same user ID / password, you will
be able to log in several DVRs at once.
5. To change the IP address, double-click the values in the column and type the numbers or
select an option. Click Set IP Address to save the settings.
Figure 2-16
Note: Most networks uses DHCP to assign IP address, if you are unsure of your network
settings, please consult your network administrators for configuration details.
6. To access the DVR, highlight the DVR and click Connect to Selected IP. The Internet Explorer
window pops up.
7. Type the user ID and password to log in. The Live View window of the DVR appears.
Note:
1. You might be required to download ActiveX for viewing the camera feed. If asked,
click Yes.
2. For details on the Live View window, please refer to 7. Remote Access to the DVR.
17
ECOR960 X1
8. You may need to turn User Account Control off if you still can’t see the Remote Live View.
9. On the computer, click Start > Control Panel > System and Security > Action Center (click
Change User Account Control Settings), the User Account Control Settings window appears.
Adjust the slide bar to Never Notify and then click OK. Restart your computer if requested.
18
ECOR960 X1
2.6
Connecting the DVR to the Network
There are three methods to connect the DVR to the network: Router or LAN Connection, Direct
High‐Speed Connection and One‐to‐One Connection. For more information of the network,
please refer to Appendix A. Network Overview.
2.6.1
Router or LAN Connection
This is the most common connection in which the DVR is connected to a router and allows
multiple users on and off site to see the DVR on a LAN/WAN (Internet). The DVR must be
assigned an IP address that is compatible with its LAN. By setting up port forwarding on the
router, you can remotely access the cameras from outside of the LAN via the Internet. To
remotely access the Web interface, please refer to 7. Remote Access to the DVR. To set up
port forwarding, please consult the manual of the router or refer to Appendix B: Linksys &
D-Link Port Forwarding.
Straight-through LAN patch cable
Right: Pinout of a straight-through cable.
Figure 2-17
19
ECOR960 X1
Connection Procedure:

The First step is to purchase or make a straight through cable. We recommend
purchasing one if you have never made a straight through cable. Please remember you
can not use a cross-over network cable for this application.

Once you have a straight through cable, plug one end into the LAN port on the back of
the recorder and the other into the router.

Log into the EverFocus DVR menu and go to the Network Setting Menu.

To let the router automatically assign an address:


Set the Network Type to DHCP. Make sure to write down the IP address and the
Gateway.
Exit from the Menu to save settings.
To manually assign an address:

Go to a computer connected on the same network as the DVR.

Click on the Start button and choose Run.
If using Windows Vista, choose Search instead.

Type “command” and click on OK.
In Vista, you will need to double-click on the “Command Prompt” file to open it.

In the DOS prompt, type “ipconfig” and press Enter.

The network information will be displayed on a screen similar to the one below.
In Windows Vista, look for the information that says “IP v4”.
Figure 2-18
20
ECOR960 X1


Take the values for Subnet Mask and Default Gateway and input them into the DVR;
these values should be exactly the same in both devices. However, you should
change the last number of the IP address. For example, if the IP address of the
computer is 192.168.2.101, the DVR’s IP address should be 192.168.2.50.
To access the DVR from a computer simply open Internet Explorer and in the address
bar type:
http:// (IP address of the DVR)
Note: The DVR’s IP address will only work at the location of the DVR. To connect
from a different location over the Internet, see below.
To set the DVR for Internet Connection through router:

The next step is to open ports within your router. Log into the router using a PC and
open the following ports.




Ports to open: 80
If your Internet service provider blocks port 80, you can change it to a different port
in the DVR’s Network Menu Setup; open/forward that port instead.
If you are using a Linksys or D-Link router, see Chapter 8 for basic support on
setting up ports. For any other router, you will need to contact the manufacturer
for support.
To access the DVR from a computer simply open Internet Explorer and in the address
bar type:
http:// (the IP address given by your internet service provider)
Note: If you changed to a different port other than 80, you will need to include this
at the end of the IP address:
http:// (the IP address given by your internet service provider):port number

If you have a WAN Dynamic IP address and have opened the ports, go to 6.7.3 DDNS
Setup to configure the DDNS settings.
21
ECOR960 X1
2.6.2
Direct High-Speed Connection
In a Direct High‐Speed Connection, the DVR connects directly to a modem without the need
for a router. You need to set the static or dynamic WAN IP address assigned by your ISP
(Internet Service Provider) in the DVR’s configuration web pages. To access the DVR, just type
“http://xxx”, where xxx is the IP address given by your ISP. If you have a dynamic IP address,
this connection may require that you use DDNS for a reliable connection.
Figure 2-19
Connection Procedure:

The first step is to purchase or make a straight through cable. We recommend
purchasing one if you have never made a straight through cable. Please remember you
can not use a cross-over network cable for this application

Once you have a straight through cable plug one end into the LAN port on the back of
the recorder and the other into the high speed modem.

Log into the EverFocus DVR menu and go to the Network Setting Menu.

Input the Static IP address, the Subnet Mask, and the Gateway that you obtained from
the internet service provider.
Note: If you have a dynamic IP address, you can set the DVR to DHCP to automatically
detect the network settings. Therefore, it can use a dynamic IP address.

Exit from the DVR’s Menu to save the settings.

To access the DVR from a computer, open Internet Explorer and in the address bar type:
http:// (IP address given by your internet service provider)
Note: When using this type of connection, only one device can be connected to the
modem at a time. You will need to use a computer at a different location to test the
connection s.
22
ECOR960 X1
2.6.3
One-to-One Connection
You can connect directly without using a switch, router or modem. However, only the PC
connected to the DVR will be able to view the DVR. You will also have to manually assign a
compatible IP address to both the computer and the DVR. Unless the PC has another network
connection, the DVR will be the only network device visible to the PC. See the diagram below:
Right: Pinout of a crossed-over cable.
Figure 2-20
Connection Procedure:

The First step is to purchase or make a cross-over cable. We recommend purchasing one
if you have never made a cross-over cable. Please remember you can not use a straight
through network cable for this application.

Once you have a cross-over cable, plug one end into the LAN port on the back of the
DVR and the other into the network card on the back of the computer.

Log into the EverFocus DVR menu and go to the Network Setting Menu.

You must use the Static IP option for this type of connection.

Assign an IP of 192.168.001.003, a Subnet Mask of 255.255.255.000, and a Gateway of
192.168.001.001. You can ignore DNS Server.

The next step is to set the computer’s network settings to match those of the DVR. You
will need Administrator privileges on your Windows machine to do this.

To assign a fixed IP address in Windows 2000/XP, follow the instructions below:
23
ECOR960 X1

Go to Start. Double-click on Control Panel.
Figure 2-21

Click Network and Internet Connection.
Figure 2-22

Click Network Connections.
Figure 2-23
24
ECOR960 X1

Right-click on Local Area Connection and select Properties.
Figure 2-24

Click on Internet Protocol (TCP/IP) and then click Properties.
Figure 2-25


Select Use the following IP address. Assign an IP address of 192.168.1.2, a Subnet
Mask of 255.255.255.0, and a Default Gateway of 192.168.1.1 and then click OK.
Restart both of the computer and the DVR.
25
ECOR960 X1

To access the DVR from the computer, simply open Internet Explorer and in the
address bar type: http://192.168.1.3
Figure 2-26



Select Use the following IP address. Assign an IP address of 192.168.1.2, a Subnet
Mask of 255.255.255.0, and a Default Gateway of 192.168.1.1 and then click OK.
Restart both of the computer and the DVR.
To access the DVR from the computer, simply open Internet Explorer and in the
address bar type: http://192.168.1.3
26
ECOR960 X1
Chapter
3
3. Mouse and Front Panel Button Operation
There are four ways to control the OSD menu of the ECOR960 X1: with a Mouse, the Front Panel
Buttons, the supplied handheld IR Remote Control or the optional device EKB500 keyboard. For
details on the IR remote control, please refer to Appendix E, IR Remote Control. This chapter will
discuss the basic operations using the mouse and the front panel buttons.
3.1 USB Mouse Operation
3.1.1
How to Select a Channel /Enable Audio
1.
In the Live View window, you can select a channel by clicking once on the desired
channel screen. The selected screen will be highlighted by a white frame.
2.
Double clicking on a channel screen will display full screen for this channel.
3.
The DVR only supports one audio output. To enable audio out, click the Audio Icon
at lower side of the screen to switch the Audio Output function to Camera 1 ~ 4 or
disable the Audio Output function. To display function icons on the Live View window,
please refer to 4.4 Display.
Note:
1. The Audio function is unavailable for Germany.
2. The Audio Output function is only functional for Camera 1 ~ 4 (BNC 1 ~ 4 Video Inputs).
3.1.2
OSD Root Menu
1.
Right-click the mouse, the OSD Root Menu Bar appears. Move the mouse over each icon,
the title of the icon will be displayed at the top-left corner.
2.
Click on any icon to enter to the setup menus.
3.
Click the
button on the top-right corner to close the OSD Root Menu Bar.
27
ECOR960 X1
3.1.3
Field Input Options
You may found the following fields in the Configuration menu. Follow the instructions below
to configure the settings.
Text Box: Click on the box and an on-screen keyboard will appear.
Drop-Down Box: Click on the down arrow to see all selections, then directly click on an option
to select it.
Check Box: Click on the box to enable it (checked) or disable it (unchecked).
Button: Click the button to execute the function.
Bar: Slide the bar to the left or right for adjusting the set point.
On-Screen Keyboard: Click on a button to input that character. The buttons on the right and
bottom have the following functions:
Space
Enter a space
Caps
Switch to capital letters
Delete the letter
Confirm the selection
Move to right
Move to left
28
ECOR960 X1
3.2 Front Panel Buttons Operation
3.2.1
Front Panel Review
The basic principle of front panel operation is to use the Arrow Keys (Up / Down / Right / Left)
to navigate among the menu items. Press the Enter button to confirm a selection or enter the
submenu. Press the Menu button to enter the OSD Root Menu or exit from the current
menu.
3.2.2
How to Select a Channel / Enable Audio
1.
In the Live View window, you can select a channel by using the arrow keys to scroll
through each channel. The selected channel will be highlighted with a white frame.
2.
After selecting a channel (only Camera 1 ~ 4), press the Enter button to turn On / Off the
Audio function. An Audio icon
will be displayed on the upper-left corner on the
selected channel. To display function icons on the Live View window, please refer to 4.4
Display.
Note:
1. The Audio function is unavailable for Germany.
2. The Audio Output function is only functional for Camera 1 ~ 4 (BNC 1 ~ 4 Video Inputs).
3.2.3
OSD Root Menu
1.
Press the Menu button, the OSD Root Menu Bar appears. Press the right and left arrows
keys to move through each icon. The title of the icon will be displayed at the top-left
corner.
2.
Press the Enter button to enter to the setup menus.
3.
Press the Menu button to close the OSD Root Menu Bar.
29
ECOR960 X1
3.2.4
Field Input Options
You may found the following fields in the Configuration menu. Follow the instructions below
to configure the settings.
Text Box: Press the Enter button and an on-screen keyboard will appear.
Drop-Down Box: Press the Enter button to see all selections, press the up and down arrow
keys to highlight the desired option, and then press the Enter button again to select it.
Check Box: Press the Enter button to enable it (checked) or disable it (unchecked).
Button: Press the Enter button to execute the function.
Bar: Press the Enter button to activate the slider, press the right and left arrow keys to adjust
the setting, and then press the Enter button again to finalize the changes.
On-Screen Keyboard: Use the arrow keys to highlight each character and then press the Enter
button to input the selected characters. After inputting the characters, highlight Done on the
setup menu, and then press the Enter button to confirm.
Space
Enter a space
Caps
Switch to capital letters
Delete the letter
Confirm the selection
Move to right
Move to left
30
ECOR960 X1
3.3 General Operation
3.3.1
Login
In order to access ECOR960 X1 again after logging out, you may be prompted to log in for
authority identification. To log in, follow the steps below.
1.
Right-click on the screen or press any button but arrow keys on the front panel to display
Login window.
Figure 3-1
2.
Select a user account from the User name drop-down list and input the password. The
default user name and password are:
User Name: admin (lower case)
Password: 11111111
Note: For details on setting up multiple user accounts, please refer to 6.9.3 User.
To input the password by:
Using a mouse: click the Password field to bring up the on-screen keyboard. Click on the
number buttons and then click
to confirm the password.
Figure 3-2
31
ECOR960 X1
Using the front panel buttons: Use the arrow keys to select the password field and then
press the Enter button to bring up the on-screen keyboard. Use the arrow keys to
highlight each character and then press the Enter button to input the selected characters.
When finished, highlight Done and press the Enter button to confirm the password.
3.
Click (or press the Enter button when highlighted) on the Login button to log in the DVR.
3.3.2
Camera Selection
You can control each camera individually by selecting that camera. To select a camera, follow
the instructions below.
Using a mouse: Click a camera on the screen, and the selected camera will be highlighted with
a white frame. All cameras will be selected when you scrolling the mouse up / down between
the first and the last channel. You can also click the same layout type in the layout menu to
select all cameras. For example, if your screen is in 4-division, click the 4-division layout type
to select all cameras.
Using the front panel buttons: Use the arrow keys to select through the camera. The selected
camera will be highlighted with a white frame. All the cameras will be selected when pressing
the right or left arrow keys to select between the first / last camera.
32
ECOR960 X1
3.3.3
Audio Selection
In order to utilize the audio function, please follow the instructions below before switching on
the audio function.
Note: 1. The Audio function is unavailable for Germany.
2. The Audio Output function is only functional for Camera 1 ~ 4 (BNC 1 ~ 4 Video
Inputs).
1. Connect the audio source and/or audio output amplifier to the DVR.
2. Enable the Record Audio option in the Camera Setting menu.
Figure 3-3
Note that the DVR only provides one audio output. You can switch the Audio Output function
to either one from Camera 1 ~ 4. To switch the Audio Output function to the desired camera
by:
Using a mouse: On the bottom of the screen, click the Audio icon
to switch the Audio
Output function to Camera 1 ~ 4 or disable the Audio Output function.
Using the front panel buttons:
1. Use the arrow keys to select Camera 1 ~ 4.
2. Press the Enter button. An Audio icon
will be displayed on the upper-left corner on the
selected camera. To display function icons on the Live View window, please refer to 4.4
Display.
3. If you want to disable the Audio Output function on the selected camera, press the Enter
button again, the Audio icon will disappear.
33
ECOR960 X1
Chapter
4
4. OSD Root Menu
1
2
3
4
5
6
7
8
9
10
11
12
Figure 4-1
No. Name
Description
1
Playback
Click to display the Playback Bar for recording videos. For details, please
refer to 5. Playback.
2
PTZ
Click to display the PTZ Control Panel for controlling the connected PTZ
cameras. For details, please refer to 4.1 PTZ.
3
Layout
Click to display the Layout Bar as shown below. Select a layout type for
the live view display on the Main Monitor. There are 8 kinds of layouts.
4
Channel
Click to display the Channel Switching Bar as show below. To switch the
selected camera to a specific channel, please refer to 4.3 Channel
Switching.
5
Display
Click to display system information icons or status icons on the live view
screen. For details, please refer to 4.4 Display.
6
Sequence
Click to enter the auto sequential switching mode. Click again to disable.
For setting up the sequencing order, please refer to 6.8.2 Main M/T
Sequence and 6.8.3 Call M/T Sequence.
7
Monitor
Click to switch to the call monitor setting. For details, please refer to 4.6
Monitor Switching.
8
Zoom
Click to enter the Zoom mode. You can zoom in the camera view up to
x8 and navigate the camera view. For details, please refer to 4.7 Zoom.
34
ECOR960 X1
No. Name
9
Search
Description
Click to display the Search menu for setting up the Search mode for
playing back. For details, please refer to 5.3 Searching the Recordings for
Playback Back.
10
Copy
Click to display the Copy menu for archiving the recordings or log data
to the USB storage device or DVD. For details, please refer to 4.8
Archiving the Recordings or Log Data to the USB or DVD.
11
Configuration
Click to enter the Configuration menu. Please refer to 6. Configuration.
12
Logout
Click to bring up the Logout Confirmation window and then click Yes to
log out the system (see 4.9 Logout). To log in, please refer to 3.3.1
Login.
35
ECOR960 X1
4.1 PTZ
You can use the PTZ Control Panel to control the connected PTZ cameras. To bring up the PTZ
control panel, on the OSD Root Menu, click the PTZ button
.
The following actions can be performed using the PTZ Control Panel:
1. To move the camera to the desired direction and angle, click the
Direction buttons
.
2. To zoom in / out the camera view, click the Zoom buttons
3. To adjust the camera focus, click the Focus buttons
.
.
4. To adjust the Iris open to increase / decrease the amount of light in, click
the Iris buttons
.
5. To program a Preset Position (if supported by the camera):
a. Move the PTZ camera to the desired position.
b. Click the Preset button.
c. Set up a preset number for the current position by clicking the
number buttons. The number will be displayed in the number box.
d. Click the Set button to save the settings.
6. To jump to a Preset Position:
a. Click the Preset button.
b. Click the desired Preset number.
c. Click the Go button.
7. Shortcut for Preset 1 ~ 9:
a. Click digit 1 ~ 9 button without clicking any other buttons.
b. The camera will seek that Preset Position.
8. To delete a Preset Position (if supported by the camera):
a. Click the Preset button.
b. Click the desired Preset number.
c. Click the Delete button.
36
Figure 4-2
ECOR960 X1
9. To operate the Auto Pan function, click the Auto Pan button.
10. To operate the Pattern function, click the Pattern button. The Pattern is the “0” Tour in
Everfocus and Pelco PTZ cameras.
11. To operate the Tour function:
a. Click the Tour button.
b. Click the desired Tour number.
c. Click the Go button.
12. To remove a pre-configured Tour (if supported by the camera):
a. Click the Tour button.
b. Click the desired Tour number.
c. Click the Delete button.
Click C to clear the entered number in the Number Box.
Click X at the top-right corner to hide the PTZ Control Panel (see 4.1.1 Express Control of PTZ). To
display the PTZ Control Panel, right-click on the screen.
Click Exit to close the PTZ Control Panel and exit the PTZ mode.
Note: Before start using the Auto Pan, Pattern and Tour functions, you have to configure the
related settings for the connected PTZ cameras. Please refer to the User’s Manual of your PTZ
cameras.
37
ECOR960 X1
4.1.1
Express Control of PTZ
If the PTZ Control Panel has first been opened and then hidden, the mouse can be used to
control basic PTZ functions. Move your mouse cursor on the screen, the mouse cursor will
turn into a control icon (direction, focus or zoom) in different areas of the screen. You can
control PTZ direction, focus and zoom by clicking directly on the screen.
Figure 4-3
Direction Controls: When your mouse cursor turns into a direction icon, click on the screen
will force the camera to turn in that direction.
Focus Controls: When your mouse cursor turns into
, click on the screen will focus closer
the image. When your mouse cursor turns into
, click on the screen will focus farther the
image.
Zoom Controls: When your mouse cursor turns into
, click on the screen will zoom in the
image. When your mouse cursor turns into
, click on the screen will zoom out the image.
38
ECOR960 X1
4.2 Layout Switching
The ECOR960 X1 DVR has 8 kinds of screen division types available. The 8 layouts are shown as
below:
Figure 4-4
To change layout, follow the steps below:
By mouse: Right-click to bring up the OSD Root Menu and click the Layout icon
the desired layout.
. Click on
By front panel: Press the Layout button on the front panel to switch the layout type. To display a
channel in full-screen, press the channel buttons on the front panel.
4.3 Channel Switching
You can switch the selected camera to a specific channel. Follow the steps below:
1. On the live view screen, select a camera, the selected camera will be highlighted with a
white frame.
2. Right-click to display the OSD Root Menu.
3. Click the Channel icon
, the Channel Bar appears.
Figure 4-5
4. Select a channel, the selected camera will be switched to that channel.
39
ECOR960 X1
4.4 Display
You can display system and camera status on the live view screen. Follow the steps below:
1. Right-click to display the OSD Root Menu or press the Display button on the front panel to
display the system and camera status.
2. The following icons will be displayed at the top-left side of each camera stream to show each
camera’s status.
Recording
Playback
Fast forward
Fast backward
Back
Alarm
Motion
Video loss
Express copy
Audio out
pause
3. The following icons will be displayed at the bottom of the monitor to show the system
status..
Alarm
Audio
Event
HDD failure
Motion
Video loss
No network
Seq.
HD temp. too high
4. There are four display modes, and you can click the Display icon or press the Display button
on the front panel to change the display mode: (1) Display the camera and system status
icons. (2) Display only the camera status icons. (2) Display only the system status icons. (4)
Hide both the camera and system status icons.
4.5 Sequence
The sequence function is used to display each channel in sequence and for the configured
amount of time. The default setting is channels 1~16 with a dwell time of 3 seconds each –
repeated. Please refer to 6.8.2 Main M/T SEQ and 6.8.3 Call M/T SEQ for detailed information.
To enable this function:
By Mouse: Click the Sequence button
to enter the sequential switching mode.
By Front Panel: Press the “SEQ” button on the front panel to enter the sequential switching
mode.
40
ECOR960 X1
4.6 Monitor Switching
You can simultaneously connect Main and Call monitors to the DVR. On the OSD Root Menu,
click the Monitor button
to switch to the Call monitor. On the Main Monitor, right-click the
screen to display the Call Monitor control bar, and then you can configure the Layout, Channel,
Display or Sequence settings for the Call Monitor. To switch to the Main Monitor, click the
button.
Figure 4-6
Note that the Call Monitor can only be used to display camera views. The functions including the
layout, channel switching, icon display or sequencing mode of the Call Monitor can only be
configured on the Main Monitor.
4.7 Zoom
You can zoom in the camera view up to x4 and navigate the camera view using the mouse.
Figure 4-7
41
ECOR960 X1
To enter the Zoom mode:
1.
Select a camera and then click the Zoom button
on the OSD Root Menu to zoom in the
camera view to 2X. The ZOOM x 2 stamp will be displayed on the top screen.
2.
Navigate the camera view to the desired position by moving your mouse cursor over the
camera view. The mouse cursor will turn into a direction icon when you move your mouse
cursor to different portion on the camera view. Click directly on the screen can move to that
direction.
Figure 4-8
3.
Right-click the screen, the Zoom Bar appears in the middle of the screen.
4.
Click 4 to zoom in the camera view up to 4X.
5.
Click the Logout button
to log out the Zoom mode.
42
ECOR960 X1
4.8 Archiving the Recordings or Log Data to the USB or DVD
You can archive the recordings or log data (event and motion) to the USB storage device or the
DVD. On the OSD Root Menu, click the Copy icon
, the following menu appears.
Note: It's highly recommended to use a DVD+R/+RW with 4x or higher speed disc for recording.
Figure 4-9
Camera: Select the desired cameras.
Copy data type: If you want to copy the recordings from the selected cameras to the USB, select
Video. If you want to copy the log data to the USB, select Non-Video and then select the desired
log data (event / motion).
Player: Check the box to include the EFPlayer program in the copy. You can use the EFPlayer to
play back the recordings stored in the computer.
Start Date / Time: Click to bring up the on-screen keyboard / clock to select the start date /
time.
End Date / Time: Click to bring up the on-screen keyboard / clock to select the end date / time.
Copy To: Select whether you want to copy to USB or DVD. The log data can only be archived to
the USB storage device. Note that the DVD burner is unavailable for Germany.
Copy: Click to start archiving.
43
ECOR960 X1
4.9 Logout
You can log out the DVR by clicking the Logout icon
on the OSD Root Menu to bring up
the Logout confirmation window as Figure 4-6. Press “Yes” when you are ready to logout of the
system. You will need to login again before accessing the OSD Root Menu.
Figure 4-10
If you do not need the Login / Logout step before entering the Root Menu, please uncheck the
Login box in the user Management setting page. For more details, please refer to 6.9.3 User.
Figure 4-11
44
ECOR960 X1
4.9.1
Temporarily Logout
You can temporarily log out the DVR by clicking the Logout icon
on the OSD Root
Menu. This function is designed for use in conjunction with the Covert Camera function. Once
you click the Logout icon, the camera streams will be hidden on the Live View / Sequence
Mode. However, the DVR will still record the videos and the recordings can be played back. To
enable the Temporarily Logout function, follow the steps below:
1. Ensure the User Login box is Unchecked (Figure 4-11).
2. Select the cameras to be hidden once enabling the Temporarily Logout function and then
check the Covert box (Camera Setting > Basic Setting).
Figure 4-12
3. Click the Logout icon on the OSD Root Menu, the Logout menu appears.
Figure 4-13
4. Click the Yes button and the selected camera streams will be hidden on the Live View /
Sequence Mode.
5. To disable the Temporarily Logout function, simply right-click the screen to bring up the
OSD Root Menu, and then you can start controlling the DVR.
45
ECOR960 X1
Chapter
5
5. Playback
You can use the Quick Playback function to play back the recordings start from the pre-configured
time or use the Search functions to search for the desired recordings for playing back.
5.1 Quick Playback
To start using the Quick Playback function, follow the steps below:
1.
To set up the start time of the recording, on the OSD menu, check the Quick Playback box to
enable the configured time in the field below.
2.
Enter the desired time for playing back the recording. Take the below image for example, if
the current system clock time is 17:35:00, the start time for the playback recording will start
from 17:34:00 (60 seconds ago from 17:35:00).
Figure 5-1
3.
On the Live View Window, select a desired camera, right-click to bring up the OSD Root
Menu and then click the Playback button
4.
.
The recording has been playing back and the Playback Bar appears on the bottom of the
screen.
46
ECOR960 X1
5.2 Playback Bar
The playback bar is the fastest way to show video from the exact time which users want to see.
The playback bar allows users to see both a timeline and the current playback indicator. Users can
then click the timeline to move the indicator to the desired position.
1
2
3
7
4
11
10 12
2012/05/25 00:00:00
14
5
9
2012/05/25 00:00:00
15
6
8
13 6
6
2012/05/25 00:00:00
16
Figure 5-2
No. Name
Description
1
Stop
Click to stop playing back and exit the playback mode.
2
Slow Reverse
Click to start slow reversing.
3
Pause
Click to pause.
4
Slow Forward
Click to start slow forwarding.
Time Bar
Move the slider to the left / right on the Time Bar to select the
time for playing back. The status of each camera is presented by
different colors on the Time Bar. GreenNormal,
OrangeMotion, BlueVideo Loss, RedAlarm Event.
5
6
Time Bar Scale
7
Express Copy
Use the + and - buttons to adjust the time scale range for the
bar. The scale range includes 5 options (levels). When changing
the level, the Start Time and End Time will change.
L1: Entire Time Bar scale is 2 and half days.
L2: Entire Time Bar scale is 30 hours.
L3: Entire Time Bar scale is 1 hour.
L4: Entire Time Bar scale is 10 minutes.
L5: Entire Time Bar scale is 1 minute.
Click to bring up the Copy menu for archiving the recordings / log
data to the USB storage device or DVD burner. For details, please
refer to 4.8 Archiving the Recordings or Log Data to the USB or
DVD.
47
ECOR960 X1
No. Name
Description
8
Close
Click to hide the Playback Bar.
9
Fast Reverse
Click to start fast reversing.
10
Reverse
Click to start reversing.
11
Forward
Click to start forwarding.
12
Fast Forward
Click to start fast forwarding.
13
Playback Speed
Indicates the current Playback Speed.
14
Start Time
Indicates the playback start time.
15
Current Playback Time
Indicates the current playback time.
16
End time
Indicates the playback end time.
48
ECOR960 X1
5.3 Searching the Recordings for Playing Back
You can search the recordings for playing back by using the Search menu. On the left side of the
Search menu, select Time Search, Event Search, Smart Search or Snapshot Search to enter to
the setup menu.
To bring up the Search menu:
By Mouse: Right-click to bring up the OSD Root Menu, and then click the Search button
By Front Panel: Press the Search button.
Figure 5-3
49
.
ECOR960 X1
5.3.1
Time Search
Figure 5-4
Start Date: Click to bring up the on-screen keyboard to select the date.
Start Time: Click to bring up the on-screen clock to select the time.
Play: Click to start playing back.
50
ECOR960 X1
5.3.2
Event Search
Figure 5-5
Start Date / End Date: Click to bring up the on-screen keyboard to select the start / end date.
Start Time / End Time: Click to bring up the on-screen clock to select the start / end time.
Camera: Select the desired cameras to be searched.
Event: Select an event type to be searched.
Search: Click to start searching. The search results will be listed in the Event List menu as
shown below.
Figure 5-6
Prev Page / Next Page: Click to go to the previous / next page.
Unlock / Lock: Click to unlock / lock the selected items. The locked items will be
recorded in a write protected segment of the hard disk (will not be overwritten). The
DVR will lock a period of time when the alarm occurs. The length of the time depends
on DVR setting (see 6.7.2 Lock / Format).
Delete: Click to delete the selected items.
Play: Click to playback the selected items.
Copy: Click to copy the selected item to the USB storage device.
51
ECOR960 X1
5.3.3
Smart Search
The Smart Search function allows users to search for the motion event recordings. You can
set up the motion areas in this setup menu and then search for the motion events within the
specified time.
Figure 5-7
Start Date / End Date: Click to bring up the on-screen keyboard to select the start / end date.
Start Time / End Time: Click to bring up the on-screen clock to select the start / end time.
Camera: Select a desired camera to be searched.
Grid Setting: Click to set up the motion areas. The Motion Grid Setup menu appears.
Search: Click to start searching. The search results will be listed in the Event List menu (see
Figure 5-5).
To set up the Motion Grid:
1. Click on the image and the grid will be displayed.
2. To set up a motion area, drag a rectangle with your mouse (from top to bottom /
upper-left to lower-right). The selected areas will be highlighted in green (see image
below).
3. To delete a motion area, drag a rectangle with your mouse (from bottom to top /
lower-right to upper-left).
4. Follow Step 2 to set up multiple motion areas if necessary.
52
ECOR960 X1
5. Click the Save & Back button to save the settings and then return to the Smart Search
menu.
Figure 5-8
Set All: Click to select the entire area.
Clear All: Click to clear all the selected areas.
Save & Back: Click to save the configured motion areas and return to the Smart Search
menu.
Cancel: Click to cancel all changes and return to the Smart Search menu.
53
ECOR960 X1
5.3.4
Snapshot Search
You can display video frames in snapshot and resume a video from where the snapshot has
been set up.
Figure 5-9
Search Date: Click to bring up the on-screen keyboard / clock to select the date / time.
Search Direction: Click to search forward / backward based on the setup time above.
Search Camera: Select a desired camera to be searched.
Result Interval: Click to set up the interval for the snapshots of the video frame. For example,
if you select 5 minutes, the video frame will be snapshotted with 5-minute interval (see image
below).
Search: Click to start searching. The search results will be displayed in four-screen division
(see image below).
54
ECOR960 X1
To resume the video:
1. Click the Search button, the search results are displayed in four-screen division. In this
picture, you can see the time layouts on the upper-left corner of each snapshot, which are
set up with 5-minute interval.
Figure 5-10
2. Right-click on the screen, the Resume Playback Bar appears in the middle of the screen.
Previous Play Close Next
3. Click the Previous or Next buttons to display the previous / next snapshots.
4. Select a snapshot by clicking on the snapshot, the selected snapshot will be highlighted
with a white frame.
5. Click the Play button to resume the video.
6. Click the Close button to close the Resume Playback Bar and then return to the Snapshot
Search menu.
55
ECOR960 X1
Chapter
6
6. Configuration
The ECOR960 X1 can be configured through a series of menus on screen by using a Mouse, front
panel buttons or the supplied IR Remote Control. The following operations are examples of using
a Mouse. This chapter describes the functions and options of the Configuration Setting in the
on-screen display (OSD) menus. Right-click the mouse, the OSD Root Menu appears. Click the
Configuration button
appears.
, the following Configuration Menu displayed with 10 setup options
Figure 6-1
56
ECOR960 X1
List of Configuration Options:
Please find the topic of interest by referring to the section prefixed to each option.
6.1 Express
6.2 Camera Setting
6.3 Record & Play
6.4 Alarm & Event
6.5 Schedule Setting
6.6 Network Setting
6.7 Disk
6.8 Display Setting
6.9 System Setting
6.10
Information
6.2.1
6.2.2
6.2.3
6.2.4
6.3.1
6.3.2
6.3.3
6.4.1
6.4.2
6.5.1
6.5.2
6.5.3
6.5.4
6.6.1
6.6.2
6.6.3
6.6.4
6.6.5
6.6.6
6.7.1
6.7.2
6.8.1
6.8.2
6.8.3
6.9.1
6.9.2
6.9.3
6.9.4
6.9.5
6.9.6
6.10.1
6.10.2
Basic Setting
Video Adjust
Motion
Video Loss
Record
Built-in Cal.
Play
Alarm
Event
Express Setup
Holidays
Schedule
Alarm Action
LAN
Email
DDNS
Alarm Server
Remote / Mobile
Network Test
Disk
Lock / Format
Monitor OSD
Main Monitor Sequence
Call Monitor Sequence
Date / Time
Daylight Saving Time
User
I/O Control
Misc.
Quick Archive
System
Log
57
ECOR960 X1
6.1 Express
You can configure the global express settings for all cameras.
Figure 6-2
Date: Click to bring up the on-screen keyboard to set up the system date.
Time: Click to bring up the on-screen clock to set up the system clock.
Record Mode: Select a recording mode from the drop-down list.
Blank: Select this option for cameras to keep the current individual record settings without
any changes. Please refer to 6.5.1 Express Setup for more details.
Normal+Event: Continuous and Event recordings. Set up the estimated number of hours per
day for event recording.
Event Only: Event recordings only. Set up the estimated number of hours per day for event
recording.
Schedule Record: Schedule recordings.
Resolution: Select a recording resolution for the main stream.
58
ECOR960 X1
Record With: Select a record method.
Blank: Select this option for cameras to keep the current individual record method without
any changes.
Preset Settings: Select this option and further set up the recording quality. For details,
please refer to Appendix D. Express Setup Recording Value Selection Rules.
Recording Days: This option is not available for Schedule Record. Set up the maximum
recording days. For details, please refer to Appendix D. Express Setup Recording Value
Selection Rules.
Network Type: Select a network type for all cameras.
Static IP: Set up a static IP for the DVR. This type of address is stable and cannot change, but
the user has to make sure there are no address conflicts with other network-connected
devices.
DHCP: Select this item for the DHCP server to automatically assign an IP address for the
DVR.
PPPoE: This is a DSL-connection application (no router). The ISP will ask the user to input a
username and password. Contact your ISP for these details. Note only LAN1 supports PPPoE.
IP Address: This field shows the current IP Address for the DVR. If Fixed IP address is used then
this value must be set manually. If DHCP or PPPoE is selected, this value will be assigned
automatically.
Subnet Mask: This field shows the subnet mask for your network so the DVR will be recognized
within the network. If DHCP or PPPoE is selected, this value will be assigned automatically.
Gateway: This field shows the gateway for your network so the DVR will be able to communicate
outside the network. If DHCP or PPPoE is selected, this value will be assigned automatically.
DNS server 1: This field shows the primary DNS server for your network. When DHCP is selected
and an internet connection is available, this value will be assigned automatically. This field must
be assigned correctly if you plan to use the DDNS feature (refer to 6.6.3 DDNS for more details).
DNS server 2: This field shows the secondary DNS server for your network.
Note: The default addresses in the machine are for internal testing only. You must supply your
own addresses to comply with your network. Refer to Section 6.6 Network Setting for more
details.
Apply: Click to save and apply the settings to the DVR. The system will automatically adjust the
recording frame rate according to your settings.
59
ECOR960 X1
6.2 Camera Settings
You can configure the settings for individual camera. The setting options include Basic Setting,
Video Adjust, Motion and Video Loss.
6.2.1
Basic Setting
Figure 6-3
Camera: Select a camera to be configured.
Title: Click to bring up the on-screen keyboard for assigning a title for the selected camera.
Each title supports up to 16 characters.
Install: Check the box to enable the selected camera.
Covert: Check the box to hide the camera stream in Live View and Sequence modes. However,
the DVR will still record the videos and the recordings can be played back by users who have
the privilege to playback. For details on enabling the Covert function, please refer to 4.9.1
Temporarily Logout.
Record Mode: Select a record mode from the drop-down list.
Normal+Event: Continuous and Event recordings.
Event Only: Event recordings only.
60
ECOR960 X1
Resolution: Select the most suitable resolution for your needs. Please note that if you select
different modes in the Aspect Ratio drop-down list at the Display Setting page (please refer to
6.8.1 Monitor OSD), there will be different resolution options in this selection list as follows:
WD1 Mode: 960x480 / 480x240 (NTSC)
960x576 / 480x288 (PAL)
D1 Mode: 720x480 / 720x240 / 352x240 (NTSC)
704x576 / 704x288 / 352x288 (PAL)
Record Quality: Select a recording quality for the Main Stream and Sub Stream. The options
include Low, Basic, Standard, High and Superior. The higher the quality, the more the HDD
space is used.
Normal Speed: Select a frame rate per second (FPS) for continuous recording. The speed is
limited by the maximum total recording capacity of the DVR as allocated across all the
installed cameras.
Event Speed: Select a frame rate per second (FPS) for event recording.
Record Audio: Check the box to enable audio recording on the DVR. Note that the Audio
function is unavailable for Germany.
PTZ ID: To allow the DVR to recognize and then control the connected PTZ camera, you have
to set up an ID for the PTZ camera. Select On and then enter an ID for the camera. This ID
must match the ID address set up on the PTZ camera. For setting up the ID address on the PTZ
camera, please refer to the User’s Manual of your PTZ camera.
PTZ: Select a PTZ speed. The higher the number is, the faster the speed is.
Apply To: Click the button to apply the same settings to the desired cameras.
61
ECOR960 X1
6.2.2
Video Adjust
You can adjust the Brightness, Contrast and Color of the selected camera.
Figure 6-4
Camera: Select a camera to adjust the following settings.
Brightness:
Move the bar to adjust the brightness.
Contrast: Move the bar to adjust the contrast.
Color: Move the bar to adjust the color.
Apply To: Click the button to apply the same settings to the desired cameras.
62
ECOR960 X1
6.2.3
Motion
You can enable the Motion Event function and configured the related settings including
motion event notifications and motion areas in this menu.
Figure 6-5
Camera: Select a camera to be configured.
Enable: Check the box to enable the Motion Event settings for the selected camera.
Log: Check the box to record motion events to log data.
Pre-alarm Record: Check the box to start copying the recordings to the hard disk from 5
seconds before the motion event occurs. Note that the pre-alarm recording rate will follow
the Normal Speed configured in the above section (see 6.2.1 Basic Setting).
Buzzer: Check the box to enable the buzzer when a motion event is triggered.
Email Notify: Check the box to send email notification when a motion event is detected. Email
operation requires valid email entered in the Email setup menu (see 6.6.2 Email).
Network Alarm: Check the box to send out a network alarm to a client PC when motion
occurs. This feature works with EverFocus’ CMS software, PowerVideo Plus. You will need to
configure the Alarm Server for the DVR to send network alarms to the client PC (see 6.6.4
Alarm Server).
63
ECOR960 X1
Auto Lock: Check the box and the events will be recorded in a write protected segment of the
hard disk (will not be overwritten). The DVR will lock a period of time when the alarm occurs.
The length of the time depends on DVR setting (see 6.7.2 Lock / Format).
Alarm Output: Select an alarm output relay. When an alarm is triggered, the signal will be
transmitted through the selected alarm output relay.
Output Type: Select an output type when an alarm is triggered.
Timeout: Select this option and then set up the Timeout Duration in the field below, the
alarm output will last for the setup duration time (1 ~ 150 seconds).
Permanent: Alarm will remain active until the user presses the “Enter” key on the IR
Remote Control or resets the alarm remotely.
Transparent: Alarm output remains as long as the alarm input is active.
Trans + Timeout: Alarm output continues until event ends, then continues for the setup
duration time (1 ~ 150 seconds).
Timeout Duration: This function only appears when you select Timeout or Trans + Timeout
options in the Output Type drop-down list. Select a duration time for the motion event. The
alarm output will last for the setup duration time between 1 and 150 seconds.
Main Monitor: Select Full Screen to force the camera which detects motion to display full
screen on the Main Monitor. The full screen camera view will last according to the Output
Type selected in the field above.
Call Monitor: Select Full Screen to force the camera which detects motion to display full
screen on the Call Monitor. The full screen camera view will last according to the Output Type
selected in the field above.
Edit Motion Grid: Press the button to bring up the Motion Setting menu. To edit the motion
grids, please refer to the instructions later in this section.
Apply To: Click the button to apply the same settings to the desired cameras.
64
ECOR960 X1
To Edit the Motion Grids:
1.
Click the Edit Motion Grid button, the Motion Setting menu appears.
Figure 6-6
2.
Click on the image and the grid will be displayed.
3.
To set up a motion area, drag a rectangle with your mouse (from top to bottom / upperleft to lower-right). The selected areas will be highlighted in green (see image below).
4.
To delete a motion area, drag a rectangle with your mouse (from bottom to top /
lower-right to upper-left).
5.
Follow Step 3 to set up multiple motion areas if necessary.
6.
Sets up the Sensitivity, Min Area and Motion Delay for the motion grids.
Sensitivity: Sets up the motion sensitivity for the grids. The larger the number, the higher
the sensitivity.
Min Area: This function is designed to prevent false detections caused by small objects. If
you select 2, only the object size larger than 2-grid size can be detected.
Motion Delay: This function is designed to prevent false detections caused by continuous
motions. Select a delay time in seconds to start detecting motion after x second(s).
7.
Click the Save & Back button to save the settings and then return to the Motion menu.
65
ECOR960 X1
6.2.4
Video Loss
You can enable the Video Loss Event function and configured the video loss event
notifications in this menu.
Figure 6-7
Camera: Select a camera to be configured.
Enable: Check the box to enable the Video Loss event settings for the selected camera.
Log: Check the box to record video loss events to log data.
Pre-alarm Record: Check the box to start copying the recordings to the hard disk from 5
seconds before the video loss event occurs. Note that the pre-alarm recording rate will follow
the Normal Speed configured in the above section (see 6.2.1 Basic Setting).
Buzzer: Check the box to enable the buzzer when a video loss event is triggered.
Email Notify: Check the box to send email notification when a video loss event is detected.
Email operation requires valid email entered in the Email setup menu (see 6.6.2 Email).
Network Alarm: Check the box to send out a network alarm to a client PC when video loss
event occurs. This feature works with EverFocus’ CMS software, PowerVideo Plus. You will
need to configure the Alarm Server for the DVR to send network alarms to the client PC (see
6.6.4 Alarm Server).
Alarm Output: Select an alarm output number. When an alarm is triggered, the signal will be
transmitted through the alarm output relay.
66
ECOR960 X1
Output Type: Select an output type when an alarm is triggered.
Timeout: Select this option and then set up the Timeout Duration in the field below, the
alarm output will last for the setup duration time (1 ~ 150 seconds).
Permanent: Alarm will remain active until the user presses the “Enter” key on the IR
Remote Control or resets the alarm remotely.
Transparent: Alarm output remains as long as the alarm input is active.
Trans + Timeout: Alarm output continues until event ends, then continues for the setup
duration time (1 ~ 150 seconds).
Timeout Duration: This function only appears when you select Timeout or Trans + Timeout
options in the Output Type drop-down list. Select a duration time for the motion event. The
alarm output will last for the setup duration time between 1 and 150 seconds.
Apply To: Click the button to apply the same settings to the desired cameras.
67
ECOR960 X1
6.3 Record and Play
You can configure the basic recording settings on the hard disk. You can also configure the
settings for Quick Playback.
6.3.1
Record
You can enable the Video Loss Event function and configured the video loss event
notifications in this menu.
Figure 6-8
Record Overwrite: Check the box to overwrite the hard disk when it is full. Note that unless
this box is checked, or the DVR will stop recording when the hard disk is full. The use of record
overwrite is strongly recommended. If you do not use this feature, please be sure to enable
the Event setting for HD Full for notification (see 6.4.2 Event).
Schedule Record: Check the box to record videos according to the setup Schedule (see 6.5
Schedule Setting).
Time Stamp: Select Bottom or Top to record the system date and time on the bottom / top of
the image. Select off will not record the system date and time in the recordings.
Record Status Relay Output: Select a number to monitor the recording status of the selected
alarm relay. The recording status of the selected alarm relay will be transmitted to the alarm
output device.
Auto Erase Video: The hard disk will automatically erase video after it has been on the hard
drive for the selected number of days. To use the maximum hard drive space, choose “OFF”.
(See Record Overwrite and notes above.) This feature is useful if local rules and regulations
require recorded video to be discarded after a specific number of days, or to limit the
retention of older recorded video to clear space in anticipation of event recording.
68
ECOR960 X1
6.3.2
Built-in Calculator
The built-in calculator can be used to give a rough estimation of the total recording time for
the DVR with the current settings. In order to compute the estimation as accurate as possible,
please enter the expected number of hours the motion / alarm recordings will take per day.
Figure 6-9
Motion: Select the expected number of hours the motion recordings will take per day.
Alarm: Select the expected number of hours the alarm recordings will take per day.
Note: if the total hour of Motion and Alarm is more than 24 hours, the calculator will assume
that motion and alarm recordings take place for the entire 24-hour period.
Estimate: Click this button and the result will be displayed at the bottom of the screen.
69
ECOR960 X1
6.3.3
Play
You can set up the Quick Playback start time in this menu.
Figure 6-10
Quick Playback: Check the box to enable the configured playback start time in the below
field.
Playback from X seconds ago: Set up a time between 60 and 3600 seconds for the playback
start time. When you click the Play button on the front panel, the system will play back the
recordings start from the setup time.
70
ECOR960 X1
6.4 Alarm & Event
You can configure the Alarm / Event settings in this menu.
6.4.1
Alarm
Figure 6-11
Alarm: Select an Alarm input number from 1 to 16.
Enable: Check the box to enable the Alarm trigger function for the selected alarm input.
Log: Check the box to record alarm events to log data.
Pre-alarm Record: Check the box to start copying the recordings to the hard disk from 5
seconds before the alarm event occurs. Note that the pre-alarm recording rate will follow the
Normal Speed configured in the earlier section (see 6.2.1 Basic Setting).
Buzzer: Check the box to enable the buzzer when an alarm event is triggered.
Email Notify: Check the box to send email notification when an alarm event is detected. Email
operation requires valid email entered in the Email setup menu (see 6.6.2 Email).
Network Alarm: Check the box to send out a network alarm to a client PC when an alarm
event occurs. This feature works with EverFocus’ CMS software. You will need to configure
the Alarm Server for the DVR to send network alarms to the client PC (see 6.6.4 Alarm Server).
71
ECOR960 X1
Auto Lock: Check the box and the events will be recorded in a write protected segment of the
hard disk (will not be overwritten). The DVR will lock a period of time when the alarm occurs.
The length of the time depends on DVR setting (see 6.7.2 Lock / Format).
Alarm Output: Select an alarm output number. When an alarm is triggered, the signal will be
transmitted through the selected alarm output relay.
Output Type: Select an output type when an alarm is triggered.
Timeout: Select this option and then set up the Timeout Duration in the field below, the
alarm output will last for the setup duration time (1 ~ 150 seconds).
Permanent: Alarm will remain active until the user presses the “Enter” key on the IR
Remote Control or resets the alarm remotely.
Transparent: Alarm output remains as long as the alarm input is active.
Trans + Timeout: Alarm output continues until event ends, then continues for the setup
duration time (1 ~ 150 seconds).
Timeout Duration: This function only appears when you select Timeout or Trans + Timeout
options in the Output Type drop-down list. Select a duration time for the motion event. The
alarm output will last for the setup duration time between 1 and 150 seconds.
Main Monitor: Select Full Screen to force the camera associated with the selected alarm
number to display full screen on the Main Monitor. The full screen camera view will last
according to the Output Type selected in the field above.
Call Monitor: Select Full Screen to force the camera associated with the selected alarm
number to display full screen on the Call Monitor. The full screen camera view will last
according to the Output Type selected in the field above.
Record: Select a camera to start recording when the associated alarm number is triggered.
Input Type: Select an input type when the selected alarm number is triggered. The options
include N.O. and N.C.
Active Camera: This function is for associating an alarm trigger with a specific camera. For
example, if you set up an external motion detector near Camera 2, you can select Camera 2 in
this field. The alarm will be associated with this camera for full screen display, event logging
and PTZ actions.
PTZ: If the Active Camera selected above is a PTZ camera, you can further set up the PTZ
actions in this field.
Apply To: Click the button to apply the same settings to the desired cameras.
72
ECOR960 X1
6.4.2
Event
You can configure the event settings and enable the Buzzer or Email alert for notifications.
The event options include: Fan Failure, HD Temperature, HD Failure, HD Full, HD Off, Power
Loss and Network Loss.
6.4.2.1
Fan Failure
Figure 6-12
Log: Check the box to record alarm events to log data.
Buzzer: Check the box to enable buzzer when fan is not working.
Email Notify: Check the box to send email notification when an alarm event is detected. Email
operation requires valid email entered in the Email setup menu (see 6.6.2 Email).
Network Alarm: Check the box to send out a network alarm to a client PC when an alarm
event occurs. This feature works with EverFocus’ CMS software. You will need to configure
the Alarm Server for the DVR to send network alarms to the client PC (see 6.6.4 Alarm Server).
Alarm Output: Select an alarm output number. When an alarm is triggered, the signal will be
transmitted through the selected alarm output relay.
Output Type: Output action will be Transparent and cannot be changed (alarm output
remains as long as the alarm condition is active).
73
ECOR960 X1
6.4.2.2
HD Temperature
Figure 6-13
Log: Check the box to record alarm events to log data.
Buzzer: Check the box to enable buzzer when Hard Disk’s (HD) temperature is over the “Temp.
Warning Limit”.
Email Notify: Check the box to send email notification when Hard Disk’s (HD) temperature is
over the “Temp. Warning Limit”. Email operation requires valid email entered in the Email
setup menu (see 6.6.2 Email).
Network Alarm: Check the box to send out a network alarm to a client PC. This feature works
with EverFocus’ CMS software. You will need to configure the Alarm Server for the DVR to
send network alarms to the client PC (see 6.6.4 Alarm Server).
Stop Recording: Check box to stop recording when HD’s temperature is over the “Temp.
Warning Limit”.
Temp. Warning Limit: Sets the trigger temperature for HD Temperature event actions.
Choose between 50°C /122°F and 70°C /158°F.
Alarm Output: Select an alarm output number. When an alarm is triggered, the signal will be
transmitted through the selected alarm output relay.
Output Type: Output action will be Transparent and cannot be changed (alarm output
remains as long as the alarm condition is active).
74
ECOR960 X1
6.4.2.3
HD Failure
Figure 6-14
Log: Check the box to record alarm events to log data.
Buzzer: Check the box to enable buzzer when HD fails.
Email Notify: Check the box to send email notification when HD fails. Email operation
requires valid email entered in the Email setup menu (see 6.6.2 Email).
Network Alarm: Check the box to send out a network alarm to a client PC when HD fails. This
feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for
the DVR to send network alarms to the client PC (see 6.6.4 Alarm Server).
Alarm Output: Select an alarm output number. When an alarm is triggered, the signal will be
transmitted through the selected alarm output relay.
Output Type: Output action will be Transparent and cannot be changed (alarm output
remains as long as the alarm condition is active).
75
ECOR960 X1
6.4.2.4
HD Full
Figure 6-15
Log: Check the box to record alarm events to log data.
Buzzer: Check the box to enable buzzer when HD is full.
Email Notify: Check the box to send email notification when HD is full. Email operation
requires valid email entered in the Email setup menu (see 6.6.2 Email).
Network Alarm: Check the box to send out a network alarm to a client PC when HD is full.
This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server
for the DVR to send network alarms to the client PC (see 6.6.4 Alarm Server).
Alarm Output: Select an alarm output number. When an alarm is triggered, the signal will be
transmitted through the selected alarm output relay.
Output Type: Select an output type when HD is full.
Timeout: Select this option and then set up the Timeout Duration in the field below, the
alarm output will last for the setup duration time (1 ~ 150 seconds).
Permanent: Alarm will remain active until the user presses the “Enter” key on the IR
Remote Control or resets the alarm remotely.
Transparent: Alarm output remains as long as the alarm input is active.
Trans + Timeout: Alarm output continues until event ends, then continues for the setup
duration time (1 ~ 150 seconds).
Timeout Duration: This function only appears when you select Timeout or Trans + Timeout
options in the Output Type drop-down list. Select a duration time for the event. The alarm
output will last for the setup duration time between 1 and 150 seconds.
76
ECOR960 X1
6.4.2.5
HD Off
Figure 6-16
Buzzer: The buzzer will activate when fan is not working.
Email Notify: Check the box to send email notification when HD is off. Email operation
requires valid email entered in the Email setup menu (see 6.6.2 Email).
Network Alarm: Check the box to send out a network alarm to a client PC when HD is off. This
feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for
the DVR to send network alarms to the client PC (see 6.6.4 Alarm Server).
Alarm Output: Select an alarm output number. When an alarm is triggered, the signal will be
transmitted through the selected alarm output relay.
Output Type: Select an output type when HD is off.
Timeout: Select this option and then set up the Timeout Duration in the field below, the
alarm output will last for the setup duration time (1 ~ 150 seconds).
Permanent: Alarm will remain active until the user presses the “Enter” key on the IR
Remote Control or resets the alarm remotely.
Transparent: Alarm output remains as long as the alarm input is active.
Trans + Timeout: Alarm output continues until event ends, then continues for the setup
duration time (1 ~ 150 seconds).
Timeout Duration: This function only appears when you select Timeout or Trans + Timeout
options in the Output Type drop-down list. Select a duration time for the event. The alarm
output will last for the setup duration time between 1 and 150 seconds.
77
ECOR960 X1
6.4.2.6
Power Loss
Figure 6-17
Log: Check the box to record alarm events to log data.
Email Notify: Check the box to send email notification when power has been restored. Email
operation requires valid email entered in the Email setup menu (see 6.6.2 Email).
Network Alarm: Check the box to send out a network alarm to a client PC when power has
been restored. This feature works with EverFocus’ CMS software. You will need to configure
the Alarm Server for the DVR to send network alarms to the client PC (see 6.6.4 Alarm Server).
Note: As alarms and emails cannot be transmitted without power, the log entry is made when
power is restored, and any notifications cannot be made until that time.
78
ECOR960 X1
6.4.2.7
Network Loss
Figure 6-18
Log: Check the box to record alarm events to log data.
Buzzer: Check the box to enable buzzer when network is lost.
Alarm Output: Select an alarm output number. When an alarm is triggered, the signal will be
transmitted through the selected alarm output relay.
Output Type: Select an output type when the network is lost.
Timeout: Select this option and then set up the Timeout Duration in the field below, the
alarm output will last for the setup duration time (1 ~ 150 seconds).
Permanent: Alarm will remain active until the user presses the “Enter” key on the IR
Remote Control or resets the alarm remotely.
Transparent: Alarm output remains as long as the alarm input is active.
Trans + Timeout: Alarm output continues until event ends, then continues for the setup
duration time (1 ~ 150 seconds).
Timeout Duration: This function only appears when you select Timeout or Trans + Timeout
options in the Output Type drop-down list. Select a duration time for the event. The alarm
output will last for the setup duration time between 1 and 150 seconds.
Note: This function only checks the physical connection (link) to the network. Any network
behavior that blocks data connectivity (blocked ports, IP addressing errors, etc.) is not
detected by this function.
79
ECOR960 X1
6.5 Schedule Setting
You can set up the recording schedule with the desired time, event types or FPS.
6.5.1
Express Setup
You can set up a weekly recording schedule for the DVR to automatically record videos.
Figure 6-19
Weekend Start: Select a start date and time for the weekend.
Weekend End: Select an end date and time for the weekend.
Daytime Start: Select a weekday start time (Nighttime schedule ends when Daytime begins).
Daytime End: Select a weekday end time (Nighttime schedule ends when Daytime ends).
Record Type: Select a recording type for each time period.
Disable: No recording during the scheduled time period.
Normal+Event: Continuous and Event recordings.
Event Only: Event recordings only.
Normal: Select a frame rate per second (FPS) for the Continuous Recording.
Event: Select a frame rate per second (FPS) for the Event Recording.
Action: Check the box to enable the Buzzer, Alarm Out, E-mail and Network actions selected
in 6.4 Alarm & Event when an event occurs during the selected time period.
Apply: Click the button to apply the settings.
Note: For Holiday and Others, you can set up the recording schedule in 6.5.2 Holidays.
80
ECOR960 X1
6.5.2
Holidays
In addition to set up a weekly recording schedule, you can also set up a holiday recording
schedule to automatically record videos on a specific day of the year.
Figure 6-20
Date Type: Select Holiday or Others if you have configured the settings in 6.5.1 Express Setup.
The Holiday and Others are two different groups designed for you to assign special days
independently.
Recurrent Type: Select a date layout for the selected group above.
Disabled: Select to disable the Holiday / Others recording schedule.
One time: Select this option and then set up the specific date and year in the Details field.
The DVR will start recording on this specific date.
Month/date: Select this option and then set up the specific date in the Details field. The
DVR will start recording on this date yearly.
Month/Weekday: Select this option and then set up the specific date in the Details field.
The DVR will start recording on this specific date.
Details: Click to specify the date for the selected group above.
Prev: Click to go to the previous page.
Next: Click to go to the next page.
81
ECOR960 X1
6.5.3
Schedule
You can set up the camera recording mode by time of day on specific days of the week and/or
holidays and other days.
Figure 6-21
Camera: Select a camera number to change the schedule for the selected camera. Each
camera can be controlled during a 24-hour time block for Holiday (Hol), Other (Oth), Sunday
(Sun), Monday (Mon), Tuesday (Tue), Wednesday (Wed), Thursday (Thu), Friday (Fri), or
Saturday (Sat).
Time Bar: The time bar uses three different colors to distinguish each recording mode.
Gray (No Rec): No recording during this time block.
Orange (E): Only events are recorded during this time block.
Blue (N+E): (Default) Normal and event recording during this time block.
To Set Schedule using Mouse
1.
Click on desired start time block (no numbers on it) on a time bar. At this time, the
selected time block will be highlighted in blue frame and the entire time bar will be
highlighted by red frame. There are 24 blocks on the time bar representing 24 hours
respectively.
2.
Set a schedule start time by clicking on a desired start time block on a time bar. Click
again to confirm, and a new sequence number (for this new section) will show on this
block and the current and all following blocks will turn to gray. This means this new gray
timezone has a new record mode (No record).
82
ECOR960 X1
3.
Change the timezone/section to different record mode (which shows a different color) by
clicking on the first (numbered) block of any section. The color switches from gray ->
orange -> blue, every time the user clicks the first block of a section.
4.
Repeat clicking on the first block (indicated by a sequence number on it) of any timezone,
this timezone will change from one color to another, which means switching the record
mode. The color switch sequence is gray->orange->blue.
Schedule Setting using the front panel buttons
5.
Enter schedule setting mode: Select the “Schedule’ icon on the configuration menu and
press the ‘Enter’ button; the left hand column will be highlighted in a blue frame. Use the
Arrow Keys to highlight the ‘Schedule’ choice and press the “Enter” button to enter the
schedule setting mode. At this time, the whole editing area at the lower right side will be
highlighted within a blue frame.
Figure 6-22
6.
Enter camera selection mode: Use the Arrow Keys to switch to Camera selection mode.
The list of camera numbers will be highlighted with a blue frame.
Figure 6-23
83
ECOR960 X1
7.
Selecting camera: Use the Arrow Keys to select the desired camera to configure. The
selected camera number will be highlighted by a blue frame.
Figure 6-24
8.
Enter time bar editing mode: Use the Arrow Keys to switch to time bar editing mode.
When this mode is selected, all 9 time bars will be highlighted with a blue frame.
Figure 6-25
9.
Select desired time bar for setting: Press the “Enter” button; the first time bar will be
selected with a red frame. Use the Arrow Keys to select the desired time bar for setting.
Figure 6-26
84
ECOR960 X1
10. Editing blocks in a time bar: when a time bar is selected (highlighted in red frame), press
the “Enter” button, and the first block of this bar will be selected (highlighted in blue
frame). Use the Arrow Keys to select the desired block as the starting time, and press the
Enter button to confirm. At this time, the current and all following blocks will turn into
gray, which means this gray timezone has been set to the recording mode of gray (No
Rec). User can also change the timezone to a different record mode (with different
color) by following the instructions in the next step.
Figure 6-27
11. Changing recording mode (color) of a timezone: Use the rrow Keys to switch to the first
block (with number on it) of a timezone. Click the Enter button, this timezone will switch
to another color, which means switching to another record mode. The color switch
sequence is gray->orange->blue.
Figure 6-28
12. To exit the screen, press the “Menu/Esc” button as required to move up the menu levels
and, if desired, out of the menu system.
85
ECOR960 X1
Click the “Edit Timezone” button to edit the recording parameters for a time zone.
Figure 6-29
Editing Timezone:
From: Displays time zone start time.
To: Displays time zone end time.
Record: Displays Record mode.
Resolution: Select a recording resolution.
Normal: Frame rate in FPS for continuous recording. It is important to keep track of the
normal recording resources being allocated at each hours of the day. Increasing the Normal
recording resolution and/or rate can inadvertently request more recording resources than the
DVR is capable of delivering, or allocate so much of the DVRs resources that there is no excess
available for increased FPS rate and/or resolution in response to an Event.
The speed is limited by the maximum total recording capacity of the DVR as allocated across
TV standard in global setting, all the installed cameras.
Since EverFocus DVRs have the capability to change the FPS rate in response to events, it may
be advisable to reserve some recording capacity for event response.
Event: Maximum desired frame rate in frames per second (FPS) for event recording; if more
than one camera requires simultaneous event recording, the total for all cameras cannot
exceed the maximum available FPS for the DVR at the corresponding resolution setting, and
the available FPS may be divided across the cameras responding to an event.
Action: Check this box to enable notifications enabled elsewhere (Buzzer, Alarm out, E-mail,
and Network Alarm) when an event occurs.
86
ECOR960 X1
Apply to Days: This button can be used to copy schedules to other days. Select which days
you wish to copy to. "Select All" selects all days, “Clear All” deselects all days. Click “OK” to
copy the settings or "Cancel" to exit without copying.
Figure 6-30
Apply to Cameras: This button can be used to copy schedules to other cameras. Select which
cameras you wish to copy to. "Select All" selects all cameras, “Clear All” deselects all cameras.
Click “OK” to copy the settings or "Cancel" to exit without copying.
Figure 6-31
87
ECOR960 X1
6.5.4
Alarm Action
Defines recording response to “alarm” input trigger signals by time of day on specific days of
the week and/or holidays and ‘other’ days.
Figure 6-32
Alarm: Select a number to change the schedule for that alarm input trigger. Each alarm can
be set on a 24 hour time block for Holiday (Hol), Other (Oth), Sunday (Sun), Monday (Mon),
Tuesday (Tue), Wednesday (Wed), Thursday (Thu), Friday (Fri), or Saturday (Sat).
Time Bar: The time bar uses two different colors to distinguish each recoding mode.
Off: No recording during this time block.
On: Alarm action will be recorded during this time block.
To Set Schedule using Mouse:
1.
Click on the “Alarm Action” choice, then click on the right hand side of the screen. The
border for that region will now turn blue.
2.
Click on the number of the alarm trigger input you wish to configure.
be framed in blue.
3.
Click on a desired start time block on a time bar. There are 24 blocks on the time bar
representing 24 hours respectively. At this time, the selected time bar will be
highlighted by a red frame and the selected block will be highlighted in blue frame.
Initially, the selected block and all following blocks will be gray, which means this gray
timezone has been set to the recording mode corresponding to gray (alarm action
recording OFF).
88
That number will
ECOR960 X1
4.
Change the section to different mode (with a different color) by clicking on the first
block of the section. The color switches from gray -> orange -> gray, every time user
clicks the first block of a section. Orange indicates ‘alarm action recording ON’.
5.
To set the end of a timezone, select the time block following the end of the timezone
defined in the step above. The first click will highlight the block in blue. A second click
will toggle the state/color of that block and the remainder of the time bar, ending the
above defined timezone
Alarm Action Setting from front panel
1.
Enter Alarm Action setting mode: highlight the “Alarm Action: menu choice and press
the “Enter” button to enter Alarm Action setting mode. At this time, the whole editing
area at the right side will be highlighted with a blue frame.
Figure 6-33
2.
Enter alarm selection mode: Use the Arrow Keys to switch to Alarm selection mode. The
Alarm channel will be highlighted with a blue frame.
Figure 6-34
3.
Selecting alarm: Use the Arrow Keys to select an alarm number to be configured.
Selected alarm number will be highlighted with a blue frame.
Figure 6-35
89
ECOR960 X1
4.
Enter time bar editing mode: Use the Arrow Keys to switch to time bar editing mode.
The area surrounding the time bars will be highlighted with a blue frame.
Figure 6-36
5.
Select desired time bar for setting: Press the Enter button, the first time bar will be
selected and highlighted with a red frame. Use the Arrow Keys to choose the desired
time bar for setting.
Figure 6-37
6.
Editing blocks in a time bar: Press the Enter button to select that time bar for
configuration; then the first block of this bar will be selected (highlighted with a blue
frame). Use the Arrow Keys to move to the desired block for the starting time, and press
the Enter button again to confirm. At this time, the current and all following blocks will
turn into gray, which means this gray timezone has been set to the recording mode of
gray (Alarm Action off). User can also change the timezone to a different record mode by
following the instructions in the next step.
Figure 6-38
90
ECOR960 X1
7.
Changing recording mode (color) of a timezone: Use the Arrow Keys to select the first
block of a timezone. Press the Enter button, and this timezone will switch to another
color, which means switching to another recording mode. The color switch sequence is
gray->orange->gray.
Figure 6-39
Apply to Days: This button can be used to copy schedules to other days. Select which days you
wish to copy to. "Select All" selects all days, “Clear All” deselects all days. Click “OK” to copy the
settings or "Cancel" to exit without copying.
Figure 6-40
Apply to Cameras: This button can be used to copy schedules to other cameras. Select which
cameras you wish to copy to. "Select All" selects all cameras, “Clear All” deselects all cameras.
Click “OK” to copy the settings or "Cancel" to exit without copying.
Figure 6-41
91
ECOR960 X1
6.6 Network Settings
The DVR allows you to use a Web browser to remotely view and manage the system. You can
also receive live video streaming from the DVR using your smartphone.
Note: Since every Network Configuration is different, please check with your Network
Administrator or ISP to see if your DVR should use specific IP addresses and/or port numbers.
6.6.1
LAN
According to your network environment, select Static IP, DHCP or PPPoE to configure an IP
address to the DVR.
Figure 6-42
Network Type: Three options are selectable: Static IP, DHCP and PPPoE.
Static IP: User can set a fixed IP for network connection.
DHCP: DHCP server in LAN will automatically assign an IP configuration for the network
connection.
PPPoE: For direct connection to the DSL only. Verify with your ISP if they use PPPoE. Note
that only LAN1 supports PPPoE.
92
ECOR960 X1
IP address: Displays the DVR’s current IP Address. A static IP address must be set manually. If
DHCP is selected, this value will be assigned automatically.
Subnet Mask: Displays the subnet mask for your network so the DVR will be recognized
within the network. If DHCP is selected, this value will be assigned automatically.
Gateway: Displays the gateway on your network for the DVR to use when communicating
with any devices not on the local network. If DHCP is selected, this value will be assigned
automatically.
DNS Server 1: Displays the primary DNS server for your network. If DHCP is selected and an
internet connection is available, this value should be assigned automatically. This field must
have a valid DNS address in order to use the DDNS feature (see 6.6.3 DDNS).
DNS Server 2: This field shows the secondary DNS server for your network.
HTTP Port: Port number for HTTP/WEB communication.
Bandwidth Limit (Kbps): Specify, disabled / 128 K/ 256 K / 512 K / 768K/ 1M / 3M bps. This is
the maximum bandwidth that the DVR is allowed to use on the network. This is a useful
function when connecting the DVR to busy or heavily loaded networks, or when accessing the
DVR(s) over a WAN.
Reconnect: Click to reconnect the network.
Additional information:
1. Set up the DVR Network Menu according to the instructions detailed in the Networking
chapter of this DVR’s manual.
a. If using DHCP, all settings will be detected automatically. While DHCP is a useful tool
for determining the network settings, if you set up your DVR in this manner its IP
address may change at different times for different reasons, particularly after a power
failure. If the IP address of the DVR changes, you may have difficulties accessing your
DVR locally and/or remotely. It is strongly recommended that you assign a fixed (static)
IP address to your DVR, and that in order to avoid address conflicts the IP address
assigned be outside of the DHCP range of addresses your router issues to DHCP clients.
Please do not set the DHCP address issued to the DVR by the router as its static IP
address unless you take specific steps that program your router to prevent such
address conflicts.
b. If using a Fixed IP (recommended), you will need to input the information manually. In
order for DDNS to work, you must enter valid data, compatible with your network, for
all four of the network setting fields: IP address, subnet mask, default gateway and the
DNS Address (depending on your network hardware and IP configuration this may be
the IP address of your router/gateway, or it may be the actual IP address of the local
DNS server). The DNS server IP is required because your DNS server provides critical
information necessary for the DVR to communicate with the DDNS server.
93
ECOR960 X1
You can obtain the actual DNS IP from your Internet Service Provider (ISP); or, from a PC
located on the same LAN as the DVR, go to http://www.dnsserverlist.org/ to obtain a list of
the IP addresses of their recommendation of the best servers to use for your location.
2. If you are connecting through a router, make sure that you have ‘opened up’ all the
required network ports in the port forwarding section of your router’s setup options. That
is, you have directed the router to send any incoming traffic using those IP ports to the
LAN IP address of the DVR. Useful information about router port forwarding can be found
at www.portforward.com . Different routers may use different terms for port forwarding
function. For instance, D-Link calls it virtual server, Netopia calls it pinholes.
The default port for the DVR is: 80
Note: Port 80 is the default port used for Web browsing. Because of this, in order to
prevent the average user from hosting a Web server, most ISPs BLOCK traffic using port 80
from reaching the average site. If you only plan to view your DVR on a LAN, you can use
port 80, and don’t have to concern yourself with DDNS or routers. However, if you desire
remote access to your DVR, perhaps using DDNS (optional), you MUST select functional
ports and set up the port forwarding in your router. Other ports, such as 8080 and 8000
are sometimes blocked by ISPs as well.
What port(s) should be used? There are 65,535 valid IP ports to choose from. These are
broken down into three groups:
•
Well Known Ports 0 thru 1023
•
Registered Ports 1024 thru 49151
•
Dynamic and/or Private Ports 49152 thru 65535
So, rather than encounter a port conflict by choosing a port commonly used for another
purpose (like port 25 for SMTP mail or port 448 for secure sockets), choose an ‘unusual’
port number. For example, add 50,000 to your house number: 50,123 is less likely to lead
to a port conflict. For a list of the known and registered ports, see
http://www.iana.org/assignments/port-numbers
94
ECOR960 X1
6.6.2
Email
You can configure the Email settings for DVR to send Email alert when an event occurs.
Figure 6-43
SMTP Server: Assign the SMTP (e-mail) server’s name. Note that for more reliable email
service, use the server’s IP address.
SMTP Port: Assign the port number used by the SMTP server.
Authentication: Check this box if the SMTP server requires authentication (user name /
password).
SSL: Check the box if mail server needs communication to be encrypted by SSL.
User name: Input the login user name if the SMTP server requires authentication.
Password: Input the password if the SMTP server requires authentication.
Conform: Input the password again to confirm.
Sender Email: Input the e-mail address of the sender (the DVR). Sender’s e-mail address has
to match the user name and password above.
Receiver Email 1: Input the first e-mail address that event messages are sent to.
Receiver Email 2: Input the second e-mail address that event messages are sent to.
Receiver Email 3: Input the third e-mail address that event messages are sent to.
Email Subject: Input email subject.
95
ECOR960 X1
6.6.3
DDNS
DDNS (Dynamic Domain Name System) is a service used to map a domain name to the
dynamic IP address of a network device. You can set up the DDNS service for remote access to
the DVR.
DDNS assigns a domain name (URL) to the DVR, so that the user does not need to go through
the trouble of checking if the IP address assigned by DHCP Server has changed. Once the IP is
changed, the DVR will automatically update the information to the DDNS to ensure it is
always available for remote access.
Before enabling the following DDNS function, user should have applied for a host name from
the DDS service provider’s website. We support two DDNS server providers:
www.everfocusddns.com and www.dyndns.com
Note: We highly recommend that you use xxxx.everfocusddns.com for the simplicity of
setting up your DVR.
6.6.3.1
EverFocus DDNS
Note that the DNS Server 1 (6.6.1 LAN) should be set up correctly or the DDNS will not work.
Figure 6-44
DDNS Service: Select EverfocusDDNS from the drop-down list.
DVR Name: Input the desired name for the DVR. Note that the name of the DVR cannot
include a space, or a dot (period) or any special characters particularly ~ ! @ # $ % ^ & * ( ) + <
>";:.,
Register/Update: Click the button to submit and register the name to the Everfocus server.
The DDNS name you choose must be unique; that is, it must not already be in use. You should
see a message “Status Update successes!” on the screen, and then you can use this host name
for remote access to the DVR. For example, http://hostname.everfocusddns.com
96
ECOR960 X1
Note: It is not necessary to append the HTTP port number to the DDNS name. The EverFocus
DDNS server not only keeps track of your DVR’s IP address, but also keeps track of the ports.
Go to http://www.everfocusddns.com to confirm the registered name.
6.6.3.2
www.dyndns.org
Figure 6-45
DDNS Service: Select www.dyndns.org from the drop-down list.
Host name: Host name created through the dyndns account.
User name: User name of the dyndns account.
Password: Password of the dyndns account.
Conform: Input the password again to confirm.
Setup Steps:
1. Apply for a host name from www.dyndns.org.
2. Make sure that the DNS Server 1 is set up correctly (see DNS Server 1 in 6.6.1 LAN) or the
DDNS will not work.
3. Select www.dyndns.org from the DDNS Service drop-down list.
4. Enter the host name in the Host Name field. Note that the name of the DVR cannot
include a space, or a dot (period) or any special characters particularly ~ ! @ # $ % ^ & * ( )
+<>";:.,_
5. Enter the User Name / Password of the dyndns account.
6. The setting is complete. And you should now be able to remotely connect the DVR by
typing the name you created into the address bar. Example: http://hostname.dyndns.com
Note: If you are connecting through a router, make sure that you have opened up all the required
network ports in the “Port Forwarding” section of your router’s setup options. The default port
of the DVR is 80. To set up Port Forwarding, please consult the manual of the router.
97
ECOR960 X1
6.6.4
Alarm Server
You can send out the alarm notifications to EverFocus’s CMS software. Please also consult the
CMS’s user manual for network alarm settings.
Figure 6-46
Server IP1~3: IP address of client PC. The network alarm can be transmitted to up to 3
addresses.
Protocol: Select the protocol type for alarm transmission. Note the protocol selected here
should match the protocol set up for the CMS alarm server.
UDP: User Datagram Protocol.
TCP: Transmission Control Protocol.
Port: Select the transmission port for network alarm messages. The port setup here should
match the port set up for the CMS alarm server.
Network ID: The network ID is an identifier for the alarm transmitter (DVR sending the
alarm).
98
ECOR960 X1
6.6.5
Remote / Mobile
You can configure the compression format for the sub-stream for mobile device access. Select
H.264 or MJPEG codec to enable the mobile device access function.
Figure 6-47
H.264: The H.264 codec is compatible with iOS and Android MobileFocus applications and IE
Web browser viewing on iPhone, iPod touch, iPad, Android, and BlackBerry.
MJPEG: The MJPEG codec is compatible with iOS and Android MobileFocus applications and
IE Web browser viewing on iPhone, iPod touch, iPad, Android, and BlackBerry.
6.6.6
Network Testing
The Ping utility is useful in diagnosing connectivity problems by obtaining responses from
nodes progressively farther along the network. DNS functionality can also be confirmed by
entering a valid DNS name instead of an IP address.
Figure 6-48
To verify basic network connectivity between the DVR and other LAN or WAN nodes, click the
Ping button.
99
ECOR960 X1
6.7 Disk
The Disk menu is used to review the DVR’s hard drive settings and status. No value in this menu
can be configured by the operator.
6.7.1
Disk
Figure 6-49
Record Time (Start): Shows the earliest recording time of the DVR.
Record Time (End): Shows the latest or most current time on the DVR.
Disk: Select a disk number.
Health Status: Displays the current status of the selected disk.
Disk Temperature: Displays the current temperature of the selected disk.
Disk Size (Total): Shows the total space of the selected disk.
Disk Size (Usage): Shows the used space of the selected disk.
100
ECOR960 X1
6.7.2
Lock/Format
You can control the percentage of the HDD space reserved for Locked Event Recordings. You
can also format the hard disk if necessary.
Figure 6-50
Maximum Lock (%): Sets the maximum percentage of the HDD space reserved for Locked
Event Recordings. To set up the Locked Event Recordings, please select the Auto Lock item in
5.3.2 Event Search, 6.2.2 Motion or 6.4.1 Alarm.
Current Lock (%): Displays the current percentage of the locked event recordings in the HDD.
If the amount of locked event recordings has reached the maximum lock percentage, the DVR
will be unable to lock new event recordings.
Unlock All: Click this button to unlock the locked part of hard disk.
Delete All: Click this button to delete all the unlocked data in the hard disk. WARNING: This
will effectively ERASE the hard disk’s contents, except for the locked portion.
Format Disk: Click this button to format the whole HDD. WARNING: This will effectively ERASE
the ENTIRE hard disk!!
101
ECOR960 X1
6.8 Display Setting
You can configure the settings for displaying the camera / DVR information on the live view
image. You can also set up the sequencing order for the Main / Call monitor.
6.8.1
Monitor OSD
Check the boxes under the Main Monitor / Call Monitor fields will display the selected items
on the live view image.
Figure 6-51
Main Monitor / Call Monitor
Title: Check the box to display camera titles.
Date/Time: Check the box to display current date/time.
Event Status: Check the box to display event status.
HDD Status: Check the box to display hard drive status.
Playback Date/Time: Check the box to display playback date/time (only for main monitor).
Playback Status: Check the box to display playback status (only for main monitor).
Resolution: Select the suitable screen mode. Selections are: 1920x1080; 1280x1024; 800x600.
Aspect Ratio: Select the aspect ratio which best suits your cameras’ resolution. The options
are WD1 (16:9) and D1 (4:3) modes. If using 700 TVL cameras, it is recommended to select
WD1 mode for better recording quality. Please note that if you select the WD1 mode, the
camera resolution options in the Basic Setting will change to 960x480 / 480x240 (NTSC) or
960x576 / 480x288 (PAL). If selecting D1, they will change to 720x480 / 720x240 / 352x240 (NTSC)
or 704x576 / 704x288 / 352x288 (PAL) (Please see 6.2.1 Basic Setting).
102
ECOR960 X1
6.8.2
Main M/T SEQ
You can configure up to 20 steps of the sequencing order for the Main monitor. The
Sequence will repeat continuously from step 1 to step 20 until interrupted.
Figure 6-52
Step: The sequencing order.
Camera: Select a camera for the specific step.
Dwell (sec): Sets up the dwell time between 0 and 99 seconds for each step.
6.8.3
Call M/T SEQ
You can configure up to 20 steps of the sequencing order for the Call monitor. The Sequence
will repeat continuously from step 1 to step 20 until interrupted.
Figure 6-53
Step: The sequencing order.
Camera: Select a camera for the specific step.
Dwell (sec): Sets up the dwell time between 0 and 99 seconds for each step.
103
ECOR960 X1
6.9 System Setting
You can configure the general settings for the DVR in this menu.
6.9.1
Date / Time
You can set up the date and time for the DVR.
Figure 6-54
Date: Click to bring up the on-screen keyboard to set up the date.
Time: Click to bring up the on-screen clock to set up the time.
Date Format: Select a date format from the drop-down list.
Time Format: Select a time format from the drop-down list.
Time Zone: Select a time zone for the DVR to adjust to when updating from the time server.
NTP: Select Disable / Enable for NTP time synchronization.
NTP Server: Displays the time server address that the DVR uses for time synchronization.
Requires operating network configuration and WAN or LAN access to a compatible NTP server.
To find a compatible NTP address, follow the steps below:
a. Use a computer connected to the Network.
b. Click Start < Run < type “command” and then click OK.
c. In the DOS Prompt, type “ping pool.ntp.org” to find out the IP address of an NTP
Server.
NTP Update Interval: The frequency that the system automatically updates the time via the
NTP server. Select Daily, Weekly or Monthly.
104
ECOR960 X1
6.9.2
Daylight Saving Time
You can configure the settings for DVR to automatically adjust to daylight saving time.
Figure 6-55
Daylight Saving: Check the box to enable automatic daylight saving time.
Start Date: Set the start date for daylight saving time.
Start Time (hh:mm): Set the time when daylight saving time begins.
Set To (hh:mm): This is what the time will change to when daylight saving begins. For most
regions, this will be one hour ahead of the “Start Time”.
End Date: Set the end date for daylight saving time.
End Time (hh:mm): Set the time when daylight saving time ends.
The time change difference on the End Date will be the same as the difference between the
Start Time and End Time entered for the Start Date (typically 1 hour as in the example
shown).
105
ECOR960 X1
6.9.3
User
You can create multiple user accounts with different privileges. To delete an added user
account, select a user account and click the Delete button.
Figure 6-56
User Login: Check the box to enable the User Login function after logging out the DVR. For
details on logging in the DVR, please refer to 3.3.1 Login.
Auto Logoff: Check the box to automatically logoff the DVR after 3 minutes of inactivity.
There are three access levels. The tables below show the privileges of each level.
Functions
Playback
PTZ
Layout
Channel
Display
Sequence
Monitor
Zoom
Search
Copy
Configuration
View Covert Cameras
Logout
Express
Camera
Administrator
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
106
Manager
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
NO
NO
Operator
NO
NO
OK
OK
OK
OK
OK
NO
NO
NO
OK
NO
OK
NO
NO
ECOR960 X1
Record/Play
OK
NO
NO
Alarm/Event
OK
NO
NO
Schedule
OK
NO
NO
Network
OK
NO
NO
Disk
OK
NO
NO
Display
OK
OK
NO
System
OK
Note 1
Note 2
Info
OK
OK
OK
Log
OK
NO
NO
Note:
1. User submenu only. Manager only has the privilege to change own password, and to
access operator ID.
2. User submenu only. Operator only has the privilege to change own password.
6.9.3.1
Add
Click the Add button in the above figure. The Add menu appears. Set the name
(case-sensitive), password, access level and status. Click the Add button to add the new user
or the Cancel button to exit without making changes.
Figure 6-57
6.9.3.2
Edit
Select an ID and click the Edit button to bring up the menu below. Re-setup the settings and
click the Save button or click the Cancel button to exit without making changes.
Figure 6-58
107
ECOR960 X1
6.9.4
I/O Control
The I/O Control setup menu is used to define the settings for controlling the DVR through
RS-485 / RS-232 communication protocol and for DVR to control the connected PTZ cameras.
Please note that the RS-232 port on the DVR is currently reserved.
Figure 6-59
RS-232 (The RS-232 port of the DVR is currently reserved)
Type: Select Control or Text Insert.
Baud Rate: This field is to set the speed at which is used to transmit instruction or
information through the RS-232 port on the DVR. There are eight different speeds: 1200 BPS,
2400 BPS, 4800 BPS, 9600 BPS, 19200 BPS, 38400 BPS, 57600 BPS and 115200 BPS.
Data Bit: This field is the data bit at which you will be transferring. There are two settings for
this option: 8 or 7.
Stop Bit: This field is to set the stop bit for the RS-232 connection. There are two different
stop bits, 1 or 2.
Parity: This field is to select the parity level at which you will be connected. You can choose
between None, Odd, or Even parity levels.
Note: For details on the RS-232 related settings, please consult the Technical Support
Department of EverFocus.
108
ECOR960 X1
RS-485
PTZ Protocol: Select PTZ protocol, choose from the following protocols: Transparent, Pelco D,
Pelco P, or Everfocus. (Note: All cameras on the RS-485 bus must use the same protocol)
485 ID: This is the ID used by the EKB500 to send commands to the DVR. On an RS-485
connection, every device (PTZ, DVR and controller) must be assigned an unique ID number
between 0 and 127.
Baud Rate: This field is to set the speed at which is used to transmit instruction or
information through the RS-485 port on the DVR. There are eight different speeds: 1200 BPS,
2400 BPS, 4800 BPS, 9600 BPS, 19200 BPS, 38400 BPS, 57600 BPS and 115200 BPS.
Data Bit: This field is the data bit at which you will be transferring. There are two settings for
this option: 8 or 7.
Stop Bit: This field is to set the stop bit for the RS232 connection. There are two different stop
bits, 1 or 2.
Parity: This field is to select the parity level at which you will be connected. You can choose
between None, Odd, or Even parity levels.
Control: One remote control can be used to operate four DVRs. The DVR to be addressed is
selected by pressing the key corresponding to its ID number on the IR Remote control. Please
refer to Appendix E: IR Remote Control.
IR Controller ID: Set up an ID for the DVR and allow the IR remote control to control this DVR.
109
ECOR960 X1
6.9.5
Misc.
You can upgrade the latest firmware, restore the factory default settings to the DVR, upload /
save the DVR configuration settings from / to the USB or change the language in this setup
menu.
Figure 6-60
【Firmware】
Current Firmware Version: Shows the current firmware version of the DVR.
Upgrade: Click to upgrade the latest firmware. Note you will need to restore the firmware file
to the USB flash device and then connect the USB flash device to the DVR.
【Configurations】
Load Factory Default: Click to restore the DVR to factory default settings. The User Account,
Network IP Settings, and Time settings will not be affected.
Load From USB: Click to upload the DVR configurations restored in the USB flash device.
Save To USB: Click to save the DVR configurations to the USB flash device.
Language: Choose which language the DVR uses. The available languages may vary among
regions.
Allowed Remote Reboot: Check the box to enable restarting the DVR via the Network.
Figure 6-61
110
ECOR960 X1
6.9.6
Quick Archive
You can quickly archive all the recordings to the USB storage device or a DVD disc on the DVR;
or remotely archive all the recordings to the computer on the remote side. Plug an USB
storage device or insert a DVD disc before quick archiving (it's highly recommended to use a
DVD+R/+RW with 4x or higher speed disc for recording). If both of the USB storage device
and the DVD disc have been equipped on the DVR, the copies will be assigned to the USB
storage device. If the space of the storage is insufficient, the copies will end at the time when
the storage space is full. Note that the DVD burner is optional for Germany.
Quick Archive to the DVR:
Before using the Quick Archive function, set up the Archive Interval in the Quick Archive
menu. For example, if you set up 60 minutes for the Archive Interval, the DVR will archive the
recordings 60 minutes ago from the current time to the storage device on the DVR. On the
front-panel of the DVR, press and hold the Copy button, a beep will sound and the Quick
Archive process begins. The DVR will beep again when the process is complete and the DVD
disc (if it is inserted) will be ejected. The EFPlayer software will also be copied to the storage
device automatically.
Figure 6-62
Quick Archive to the Remote Computer or DVR:
On the Web interface, click the Copy icon on the top Menu Bar, click Quick Archive on the
left menu and then set up the Archive Interval. Select a Copy Type (Remote / Copy at DVR)
and then click the Copy button, the Quick Archive process begins.
Figure 6-63
111
ECOR960 X1
6.10 Information
You can see the DVR information and Log data in this menu. Or export the log data to the USB
storage device.
6.10.1 System
In the System Menu, you can only see the information of the DVR, Network or HDD. No
configuration can be done in this menu.
Figure 6-64
【System】
Version: Displays the firmware version.
Model: Displays the model name of the DVR.
NTSC / PAL: Displays the current video format automatically detected by the DVR.
S/N: Display the serial number of the DVR.
【Network】
IP: Displays the IP address of LAN 1 / LAN 2 set up in the Network or Express menu.
MAC: Displays the MAC address of LAN 1 / LAN2. This option cannot be changed.
Network ID: The ID number for EverFocus’ CMS as set up in the Alarm Server menu.
DVR Name: Displays the DDNS name if configured.
【Status】
Disk: Displays the status of the internal HDDs. Normal HDD operation is indicated by “OK”.
Fans: Displays the status of the internal fan. Normal fan operation is indicated by “OK”.
Ext 1: Displays the status of the external eSATA storage device. Normal eSATA storage device
operation is indicated by “OK”
112
ECOR960 X1
6.10.2 Log
You can choose, display or export log data using this menu.
Figure 6-65
Start Date / End Date: Click to bring up the on-screen keyboard to set up the start / end date.
Start Time / End Time: Click to bring up the on-screen clock to set up the start / end time.
Log Type: Select the desired log types.
View Log: Click to bring up the Log List shown as below.
Figure 6-66
Clear Log: Click to delete all the selected log data.
Export Log to USB: Click the Export button to export the log data to the USB storage device.
113
ECOR960 X1
Chapter
7
7. Remote Access to the DVR
7.1
Accessing the DVR on the Network
Follow the steps below to access the DVR from a computer.
1.
Open an Internet Explorer window and in the address bar type the IP address.
Local connection:
http:// (IP address from the DVR’s Network Menu): IP port used
e.g. http://192.168.1.163:2468
Internet connection:
http:// (IP address given by your Internet Service Provider): IP port used
e.g. http://57.182.67.204:2468
2.
The Login window pops up. Type the User Name and Password. The default User Name is
admin, while the password is 11111111. Click OK.
Figure 7-1
3.
Click OK to log in to the Web Interface of the DVR.
114
ECOR960 X1
7.2 Browser Security Setting
7.2.1
Installing ActiveX Controls
Follow the steps below to install the ActiveX Controls when you first connect to the DVR’s IP
address. If you do not see a yellow bar like the one the arrow is pointing at in the image
below, your security settings may be too high. If so, go to “Section 7.2.2 Enabling ActiveX
Controls.”
1. When you first connect to the DVR’s IP address, a yellow bar like the one the arrow is
pointing at should appears.
Figure 7-2
2. Right-click on the yellow bar and select “Install This Add-on…”.
Figure 7-3
3. Install the ePlusDVR.cab file when prompted to do so.
Figure 7-4
115
ECOR960 X1
4. After installing, you will return to the DVR’s Web interface.
Figure 7-5
5. Right-click on the yellow bar and select “Run Add-on…”.
Figure 7-6
6. Install the MSXML file when prompted to do so.
Figure 7-7
116
ECOR960 X1
7. Now you will be able to see the remote live page.
Figure 7-8
8. Please refer to 2.5 checking the Dynamic Address to adjust the settings of the User
Account Control if you still can’t see the remote live view.
117
ECOR960 X1
7.2.2
Enabling ActiveX Controls
Note this section is only necessary if you DO NOT see the yellow ActiveX bar (Figure 6-2) at
the top of your browser screen when you first connect to the DVR.
1. At the top of the Internet Explorer Window, click on Tools and then select Internet
Options.
Figure 7-9
2. Click the Security tab at the top of the window and then click Custom Level….
Figure 7-10
118
ECOR960 X1
3. In the Security Settings window, scroll to “ActiveX controls and plug-ins”.
Figure 7-11
Set the controls as follows:
“Enable”:
 Allow previously unused ActiveX controls to run without prompt (Internet
Explorer 7 only)
 Allow scriptlets (IE7 only)
 Automatic prompting for ActiveX controls
 Binary and script behaviors
 Display video and animation on a webpage that does not use external media player
(IE7 only)
 Run ActiveX controls and plug-ins
 Script ActiveX controls marked safe for scripting
“Prompt”:
 Download signed ActiveX controls
 Download unsigned ActiveX controls
“Disable”:
Initialize and script ActiveX controls not marked as safe
119
ECOR960 X1
4. Click OK and then choose Yes to change the security settings.
5. Close the window so you are back at the login screen.
6. Click the Refresh button to reload the page.
Figure 7-12
7. Install the ePlusDVR.cab file when prompted to do so.
Figure 7-13
8. Once the file finishes installing, you will return to the same login page as before. Type in
the user name and password and click Login to view the cameras. The default User Name
is admin, while the password is 11111111.
Figure 7-14
120
ECOR960 X1
7.3
Remote Live View
1
2
3
4
5
6
7
8
Figure 7-15
No. Name
1
Menu Bar
Description
For configuring the DVR. Please refer to 4. OSD Root Menu.
Double-click on a camera image to enlarge the current display to full
screen; double-click again or press the Esc key to return to the
normal view.
2
Live View
Window
3
4 / 9 / 16 UP
Indicates the Live View screen is in 4-division.
4
Microphone /
Speaker
Click the Microphone button to transfer audio to DVR from client
side if there is a microphone attached to the PC and an amplifier and
speaker attached to the DVR.
Click the Speaker button to transfer audio to the client side from DVR
if there is a speaker on the PC and a microphone and preamp
attached to the DVR, and audio recording is enabled on the DVR.
5
Sub / Main
6
Snapshot
7
Channel Buttons
Click to display the channel in full screen.
Status Highlight
Green: Indicates the live view is in a normal status.
Orange: indicates a motion is being detected.
Blue: Indicates video loss.
Red: Indicates an alarm / event is triggered.
Grey: Indicates the live view is disabled.
8
Click to switch between the Main stream and Sub stream.
Click the Snapshot button to save a snapshot of the video image
currently being displayed.
121
ECOR960 X1
7.4 Menu Bar
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Figure 7-16
No. Name
Description
1
Live View
Click to display the live view window.
2
Express
Click to configure the global express settings for all cameras. Please refer
to 6.1 Express.
3
Camera
Click to configure the camera settings. Please refer to 6.2 Camera
Settings.
4
Record & Play
Click to configure the record settings. Please refer to 6.3 Record & Play.
5
Alarm & Event
Click to configure the alarm / event settings. Please refer to 6.4 Alarm &
Event.
6
Schedule
Click to configure the recording schedule. Please refer to 6.5 Schedule
Setting.
7
Network
Click to configure the network settings. Please refer to 6.6 Network
Settings.
8
Disc
Click to display the HDD information. Please refer to 6.7 Disk.
9
Display
Click to configure the display settings for displaying the camera
information on the camera live view. Please refer to 6.8 Display Settings.
10
System
Click to configure the DVR time / user privilege / IO control / UI language
or upgrading firmware and etc. Please refer to 6.9 System Setting.
11
Information
Displays the system information.
12
Copy
13
Search
14
PTZ
Click to archive the recordings from the DVR to the client PC. Please refer
to 4.8 Archiving the Recordings or Log Data to the USB or DVD.
Search the recordings for remote playback. Please refer to
7.5 Remote Playback.
Click to control the connected PTZ cameras. Please refer to 4.1 PTZ.
122
ECOR960 X1
7.5 Remote Playback
To playback the recordings remotely, click the Search button on the Menu Bar. Click Time Search,
Event Search or Smart Search and then set up the settings. For more details about Search
setting, please refer to 5.3 Searching the Recordings for Playing Back.
Double-click on a recording, the following Remote Playback Window appears.
Fast Rewind Stop Play
Reverse Pause Fast Forward
Figure 7-17
123
Return to the Search
Setting Page
ECOR960 X1
Chapter
8.
8
Specifications
Model Name
System
Operating System
Number of Channels
RAM
Watchdog
Dual Streams
OSD Menu
Built-in DVD Burner
System Control
Pentaplex Operation
PTZ Protocol Supported
Video
Video Compression
Format
Video Format
Video Inputs
Main
Video Outputs
Call
Looping Outputs
Recording
Recording / Playback
Frame Rate
Recording Modes
Playback Search
Audio
Audio Input
Audio Output
Alarm
Alarm Inputs
ECOR960 X1
Embedded Linux
16CH
1 GB
Yes
Yes
Yes
Slim Type DVD Burner (Optional)
Front Panel Buttons, Mouse, Web UI, IR Remote Control
Simultaneous Live, Recording, Playback, Archive and Remote Viewing
EverFocus, Pelco D, Pelco P, Samsung, Transparent
H.264 / MJPEG
NTSC / PAL (auto detected by system)
16 x BNC
HDMI and VGA
BNC
16 x BNC
120 NTSC / 100 PAL (WD1)
240 NTSC / 200 PAL (Half WD1)
120 NTSC / 100 PAL (4CIF/D1)
240 NTSC / 200 PAL (2CIF)
480 NTSC / 400 PAL (CIF)
Continue, Schedule and Event
Date / Time, Event, Motion in Recorded Video, Snapshot by Interval
4 x RCA socket; Line level
1 x RCA socket; Line level
16 inputs
124
ECOR960 X1
Alarm Outputs
Storage Device
Internal 3.5” HDD
External Storage
Network
Ethernet
Protocol
Interface
USB 2.0
RS-232
RS-485
Ethernet
Power
General
Power Input
Power Consumption
Operating Temperature
Dimensions (W x D x H)
Weight
Language
Regulatory
Applications
Remote View Support
Mobile View Support
Functions
Video Pause
Video Loss Detection
Motion Detection
Event Log
User Interface
Control PTZ via OSD
Schedule Setting
User Access
4 x relays; 30 VDC at 1A rating
2 x SATA HDDs (Optional)
1 x eSATA port (EDA450)
1 x Gigabit Ethernet
TCP-IP / DHCP / PPPoE / DDNS / HTTP
2 x USB 2.0 port (one on Front Panel and one on Rear Panel)
3 pin terminal connector
5 pin terminal connector
1 x RJ-45
2-pin terminal block
12 VDC
60W max.
0°C~40°C / 32°F~104°F (20~80% humidity)
353 x 354.8 x 70.60mm / 13.89" x 13.96" x 3.055"
3.9 kg / 8.6 lbs (without HDDs)
English, Japanese, Traditional Chinese, Spanish, Deutsch, French,
Russian, Portuguese (Brazil), Dutch, Simplified Chinese
CE, FCC, UL
Remote live view and playback support on Internet Explorer7 and
later version
Integrated with EverFocus’ CMS
Live view on mobile browsers
Integrated with EverFocus’ Mobile applications for iOS and Android
devices
Yes
Yes
Yes
Yes
GUI (Graphical User Interface)
Yes (via both local and remote interfaces)
Supports Express and Advanced Schedule Setting
3 Levels of User Access Defined
125
ECOR960 X1
Chapter
9
9.
Troubleshooting
If you have problems with the system, run through the following checklist to see if you can solve
the problem.
The DVR will not go into record mode.



Bring up the DVR’s Menu and check under the Camera Menu. Verify that all connected
cameras are checked as “Installed” and that Record Mode is set to “Continuous”.
Check the Disk or Information Menus and verify that the internal hard drive is being
detected.
The DVR displays nothing on the main monitor.




Make sure the monitor is connected to either HDMI port or the VGA port. If the monitor
has multiple inputs, make sure it is on the correct input source and display setting.
Check that the monitor cables are good and power is on.
Verify the recorder is getting the correct supply power.
There is no display coming from one of the channels on the DVR.



In the DVR’s Camera Menu, make sure that all cameras are checked as “Installed” and
unchecked for “Covert”.
If there is still no picture, switch ports or connect a working camera to the port that has
no picture. If you get an image, the problem is coming from the camera or cable.
I cannot connect to the recorder via the internet.





Check that you can connect to the DVR on the LAN.
Check that the DVR has a static IP address and the port used by the DVR is forwarded
correctly to that IP address in the router.
Verify that your Internet Service Provider does not block the IP port being used
Make sure you are using the correct WAN IP address given by the ISP, or, if you have a
Dynamic IP, check if the IP address has changed; use DDNS to avoid problems caused by
changing ISP addresses.
126
ECOR960 X1
Appendix
A
Appendix A: Network Overview
This chapter will give you a basic instruction on how to set up the DVR for network connection. It
is highly recommended that you have a working knowledge of what a network is and how it works.
This will be helpful in completing the networking process.
Introduction to TCP / IP
TCP/IP is the group of protocols used by the Internet and most Local Area Networks (LANs)
throughout the world. In TCP/IP, every computer or other communications device that is
connected to the network has a unique IP address. By doing this you are giving your device a
unique address similar to the address of your house. An IP address is composed of four octets
(numbers in the range of 0 to 255) separated by decimal points. The IP address is used to uniquely
identify a host or computer on the LAN. For example, one computer on a network could have an IP
address of 192.168.1.127.
You should never give two or more devices the same exact IP address, but the first three octets of
an IP address is often the same for all computers in the local area network. For example, if a total
of 253 computers exist in a single LAN, the IP addresses could be assigned starting with
192.168.1.x, where x represents a number in the range of 2 to 254. In IPP address could be
compared with a telephone number.
Subnet Masks
Each host in a LAN has a subnet mask. The subnet mask is a set of octets that is used to determine
which LAN or class it belongs to. The number 255 is usually used to represent the network address
portion of the IP address and a zero is placed at the end to identify the host portion of the address.
Basically the subnet mask tells the devices how the network addresses are organized, and helps to
determine which addresses are local and which are remote (on the other side of the router).
127
ECOR960 X1
Gateway Address
Addressees are either local or remote. A gateway address is composed of four octets separated by
decimal points. The gateway address is used to uniquely identify the device on the LAN that has
access to the communications links connecting to other LANs, WANs and/or the Internet (access
to the ‘remote’ addresses).
Virtual Ports
A port number represents a "channel" or entryway for network communications. Port numbers
allow different computers to utilize network resources without interfering with each other. Port
numbers most commonly appear in network programming, particularly socket programming.
Sometimes, though, port numbers are made visible to the casual user. For example, some
websites on the Internet use a URL like the following:
http://www.sitename.com:8100/
In this example, the number 8100 refers to the port number used by the browser to connect to
the web server. The standard port number used by web sites is 80, so this number does not need
to be included with the URL (although it can be). In IP networking, port numbers can theoretically
range from 0 to 65535. Most popular network applications, though, use port numbers at the lower
end of the range (such as 80 for HTTP). Ports are similar to doors and windows of your house,
with port 80 acting as the front door. If these are not open you could not enter the house. This is
the same case with ports on a network. If the ports for a specific IP address are not open then you
could not gain access to that IP address.
Note: The term port also refers to several other aspects of network technology. A port can
refer to Ethernet connection points, such as those on a hub, switch, or router. The term port is
also used to refer to a physical connection point for peripheral devices such as serial, parallel,
and USB ports.
Another analogy would be: if a WAN IP address is similar to the phone number identify a site, IP
ports are similar to telephone extensions, in that they allow communication with specific devices
within a site that all share the same external (WAN) IP address. A router is a device which allows
multiple computers and other IP enabled equipment to share that single WAN IP address. It
functions like a “switchboard operator” – opening ports creates an association between those port
numbers and the LAN IP address of specific equipment on the LAN behind the router. When the
router sees a ‘call’ for a specific ‘extension’ (port), it directs that data stream to the (LAN IP
address of the) equipment associated with that ‘extension’ (port).
128
ECOR960 X1
Pre-Installation
Before beginning the installation, please answer the following questions:

Do you have Hi-speed Internet?
______________
There are many types of high speed Internet available. The most common ones are T1, Cable,
and DSL (in order of speed). The DVR is not compatible with a dial-up connection.
Note: EverFocus suggests having a minimum upload speed of 256KBps. This can be addressed
by your Internet Service Provider.

What type of modem/router do you have?
_________________________
Modem/router model name/ #
The modem/router was either installed by your Internet service provider or purchased by you
to establish a connection to the Internet. A router assigns different internal IP addresses to
local computers; this allows multiple computers to access the Internet through the same
external IP address.

Do you have a static IP address?
______________
A Static IP address means you use the same IP address every time you connect to the Internet.
With a static IP address, other Internet users always know the address of your location and
can easily connect with it. This makes it much simpler to host a website, email server, or other
type of server connection. Everfocus suggests using a static IP address. If this is not available,
you will need to use a dynamic IP address. This is explained below.

Do you have a dynamic IP address?
______________
A Dynamic IP address means your IP address changes each time you connect to the Internet.
We recommend asking your Internet service provider for a Static IP address. If this is not a
possibility, you may use the DDNS feature of the DVR. DDNS stands for Dynamic Domain
Name Server, a service that provides a central database where IP information can be stored
and retrieved. It allows those using a dynamic IP address to be registered centrally so users
can connect to it by name. See Chapter 7 for details on using EverFocus DDNS.
129
ECOR960 X1

What type of DVR are you installing?
______________
The default ports are
ECOR264: 80
Paragon: 80
ECOR: 80, 1600
EDR/EDVR: 80, 1600, and 37260 – 37263
EMV: 80
If the ports were changed in the Network Setup, use those port numbers.
Pre-Installation
Everfocus’ DVR can operate using one of three types of networking connections.
Simple One to One Connection: A simple one to one connection is the simplest type of network
connection. It uses a cross-over cable to make a direct connection from one computer to another
(or in this case a computer to a DVR).
Direct High Speed Modem Connection: A direct modem connection uses a standard network cable
to connect the modem directly to a computer (or in this case a modem to the DVR). This type of
connection only covers single-port modems. For a combination modem/router, use the setup
described below.
Router or LAN Connection – A local area network connection requires either a router or a
pre-existing LAN connection. This is the most common type of connection. A router allows
multiple computers and DVR’s to access each other as well as the Internet. It assigns different
internal IP addresses to the computers.
130
ECOR960 X1
Appendix
B
Appendix B: Linksys & D-Link Port Forwarding
Typical Linksys Port Forwarding
This section will cover a few simple configurations for the Linksys router. This chapter is only to
offer some help to the installer and end user. Please understand we DO NOT support this product
and will not give tech support on it. If you need additional technical support on this router you
must call Linksys.
To access the Web-based Utility, launch a web browser and type the Router’s IP address, typically
192.168.1.1, in the address bar. Then press Enter. A password request page will appear.
(Non-Windows XP users will see a similar screen.) Leave the User Name field blank. The first time
you access the router, use the default password admin. Click the OK button to continue.
The first screen that appears displays the Setup tab. This allows you to change the Router's
general settings. Change these settings as described here and click the Save Settings button to
apply your changes or Cancel Changes to cancel your changes.
131
ECOR960 X1
Click on the “Applications & Gaming” tab.
Applications and Gaming allows you to set up public services on your network, such as web
servers, ftp servers, e-mail servers, or other specialized Internet applications. (Some Internet
applications may not require any forwarding) To forward a port, enter the information on each
line for the criteria required. Descriptions of each criterion are described here.
Application - In this field, enter the name you wish to give the application.
Start/End - Enter the starting number of the range under Start and the ending number under End.
Protocol - Enter the protocol used for this application, either TCP or UDP, or Both.
IP Address - For each application, enter the IP Address of the PC running the specific application.
Enable - Click the Enable checkbox to enable port forwarding for the relevant application.
When finished making changes, click the Save Settings button to apply your changes or Cancel
Changes to cancel them.
Here is an example for how the port information might look:
HTTP 80 to 80
Both 192.168.1.50 Enable
Where 192.168.1.50 is the IP address of the DVR on the LAN, and the default port 80 is in use.
Note: If you changed port 80 in the DVR’s Network Menu, open that port instead of 80.
132
ECOR960 X1
Typical D-Link Port Forwarding
This section will cover a few simple configurations for the D-Link router. This chapter is only to
offer some help to the installer and end user. Please understand we DO NOT support this product
and will not give tech support on it. If you need additional technical support on this router you
must call D-Link.
Whenever you want to configure your network or the DI-624, you can access the Configuration
Menu by opening a web-browser and typing in the IP Address of the DI-264.
The DI-264 default IP Address is 192.168.0.1.
 Type “admin” in the User Name field
 Leave the Password blank
 Click OK
The first screen that shows up is the Home Tab. This is the starting point for all the router’s
settings and functions.
133
ECOR960 X1
Click Virtual Servers on the left to bring up the following screen.
Virtual Servers allows users who are connecting remotely to access services on the router’s Local
Network. The functions of each field are described below.
Virtual Server - Select Enabled or Disabled
Name - Enter the name referencing the virtual service
Private IP - The IP address of the device running the local services.
Protocol Type - The protocol used for the virtual service.
Private Port – The port number that the service uses on the LAN (Local Area Network).
Public Port - The port number that the services uses on the WAN (Wide Area Network).
Schedule – The time period the virtual server will be active.
When you have input all the information for a virtual server, click on Apply to add it to the list
at the bottom or Cancel to clear all fields.
Here is an example of the information for each service:
Name Private IP Protocol Private Port Public Port
Schedule
HTTP
192.168.1.50 Both
80
80
Enable
Where 192.168.1.50 is the IP address of the DVR on the LAN, and the default port 80 is in use.
Note: If you changed port 80 in the DVR’s Network Menu, open that port instead of 80.
134
ECOR960 X1
Appendix
C
Appendix C: Timing of Alarm Modes
Transparent Mode
Input Event
Alarm Duration
t
t Event = t Reaction
t Event:
t reaction:
Duration of alarm input source (motion, contact, system events...)
Resulting duration for this alarm mode, related to event record, alarm outputs, OSD
message, buzzer
Timeout + Transparent Mode
Input Event
Alarm Duration
t Event
t Duration
t
t Reaction
t Event:
Duration of alarm input source (motion, contact, system events...)
t Duration: Alarm duration for timeout, defined in the event setup menus
t reaction: Resulting duration for this alarm mode, related to event record, alarm outputs, OSD
message, buzzer
135
ECOR960 X1
Timeout Mode
Input Event
Alarm Duration
t
t Event
t Duration = t Reaction
t Event:
Duration of alarm input source (motion, contact, system events...)
t Duration: Alarm duration for timeout, defined in the event setup menus
t reaction: Resulting duration for this alarm mode, related to event record, alarm outputs, OSD
message, buzzer
Permanent Mode
Alarm Reset
Input Event
Alarm Duration
t
t Event
t Reaction
t Event:
Duration of alarm input source (motion, contact, system events...)
t Duration: Alarm duration for timeout, defined in the event setup menus
t reaction: Resulting duration for this alarm mode, related to event record, alarm outputs, OSD
message, buzzer
136
ECOR960 X1
Timeout Mode: Retrigger of Alarms
t Event:
Duration of alarm input source (motion, contact, system events...)
t Duration: Alarm duration for timeout, defined in the event setup menus
t reaction: Resulting duration for this alarm mode, related to event record, alarm outputs, OSD
message, buzzer
Timeout+Transparent Mode: Retrigger of Alarms
t Event:
Duration of alarm input source (motion, contact, system events...)
t Duration: Alarm duration for timeout, defined in the event setup menus
t reaction: Resulting duration for this alarm mode, related to event record, alarm outputs, OSD
message, buzzer
137
ECOR960 X1
Appendix
D
Appendix D: Express Setup Recording Value Selection Rules
Case 1:
Record Mode: Normal + Event
Record With: Recording days
The DVR will Auto adjust image Quality and Event frame rate to match the number of Recording
days which user selected:
According to resolution, event hours and other assumptions above, the DVR will attempt to select
one set of suitable quality and event frame rate by checking if set 1 meets the requirements, and
proceed in order unit the requirements are met. If the DVR can’t match the required record days
from one of the 8 sets, it will use set 8.
Checking Order
1
2
Normal Frame
1
1
Rate
Quality
Superior Standard
Event Frame
30
30
Rate
Case 2:
Record Mode: Event Only
3
4
5
6
7
8
1
1
1
1
1
1
Low
Low
Low
Low
Low
Low
30
15
10
7.5
5
1
Record With: Recording days
DVR will Auto adjust Quality and Event frame rate to match the Recording days which user
need:
According to resolution, event hours and other assumptions above, the DVR will attempt to select
one set of suitable quality and event frame rate by checking if set 1 meets the requirements, and
proceed in order unit the requirements are met. If the DVR can’t match the required record days
from one of the 8 sets, it will use set 8.
Checking
1
2
3
4
5
6
7
8
Order
Quality
Superior Standard
Low
Low
Low
Low
Low
Low
Event Frame
30
30
30
15
10
7.5
5
1
Rate
138
ECOR960 X1
Case 3:
Record Mode: Normal + Event or Event Only
Record With: Preset Setting
DVR will apply the settings in the table below to all cameras according to the Preset Settings.
Preset Setting Option Camera Item
Apply value
Quality
Superior
Best Quality
Normal Frame Rate
Max recording frame rate of DVR
Event Frame Rate
30
Quality
Standard
Standard Quality
Normal Frame Rate
Half of max recording frame rate of DVR
Event Frame Rate
30
Quality
Basic
Extended Quality
Normal Frame Rate
1
Event Frame Rate
10
139
ECOR960 X1
Appendix
E
Appendix E: IR Remote Control
The IR remote control is an accessory to enhance the convenient operation of the DVR. You can
perform all the settings and operations from the remote control. The effective distance is up to 33
feet line of sight.
ID number here must correspond to the
“IR Remote ID” set up in the “I/O Control Menu”.
The buttons are used to select a DVR when
there is more than one DVR installed in the
same environment. Selecting an incorrect DVR
ID will prevent the DVR from responding to
commands from the Remote Control.
Channel keys #1~16
140
EverFocus Electronics Corp.
EverFocus Taiwan:
12F, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: +886 2 2698 2334
FAX: +886 2 2698 2380
www.everfocus.com.tw
[email protected]
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: +49 2822 93940
FAX: +49 2822 939495
www.everfocus.de
[email protected]
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: +86 10 6297 3336~39
FAX: +86 10 6297 1423
www.everfocus.com.cn
[email protected]
EverFocus China - Shenzhen:
4F, No. 2, D4 Building, Wan Yelong
Industrial Park, Tangtou Road, Shiyan,
Baoan, Shenzhen, Guangdong 518101, China
TEL: +86 755 2765 1313
FAX: +86 755 2765 0337
www.everfocus.com.cn
[email protected]
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010, USA
TEL: +1 626 844 8888
FAX: +1 626 844 8838
www.everfocus.com
[email protected]
EverFocus USA - New York:
415 Oser Avenue, Unit S, Hauppauge, NY 11788, USA
TEL: +1 631 436 5070
FAX: +1 631 436 5027
www.everfocus.com
[email protected]
EverFocus Japan:
5F, Kinshicho City Building, 2-13-4
Koto-Bashi,Sumida-Ku, Tokyo, 130-0022, Japan
TEL: +81 3 5625 8188
FAX: +81 3 5625 8189
www.everfocus.co.jp
[email protected]
EverFocus Europe - UK:
Unit 12, Spitfire Business Park,
Hawker Road, Croydon Surrey, CR0 4WD, UK
TEL: +44 20 8649 9757 / +44 845 430 9999
FAX: +44 20 8649 9907
www.everfocusuk.co.uk
[email protected]
EverFocus India:
Suite 803, Housefin Bhavan, C-21,
Bandra Kurla Complex, Bandra (East),
Mumbai 400051, India
TEL: +91 22 6128 8700
FAX: +91 22 6128 8705
www.everfocus.in
[email protected]
Your EverFocus product is designed and
manufactured with high quality materials
and components which can be recycled
and reused.
This symbol means that electrical and
electronic equipment, at their end-of-life,
should be disposed of separately from
your household waste.
Please, dispose of this equipment at your
local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde entwickelt
und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass elektrische
und elektronische Geräte am Ende ihrer
Nutzungsdauer vom Hausmüll getrennt
entsorgt werden sollen.
Bitte entsorgen Sie dieses Gerät bei Ihrer
örtlichen kommunalen Sammelstelle oder
im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
P/N: 4605PCOR16B100A Ver.C

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement