INSTALL GUIDE OEM-AL(RS)-FM6-[ADS-ALCA]-EN

instaLL guiDe

OEM-AL(RS)-FM6-[ADS-ALCA]-EN

Document numbeR

16348

Revision Date

20140908

FiRmwaRe

OEM-AL(RS)-FM6-[ADS-ALCA] haRDwaRe

ADS-ALCA accessoRies

ADS-USB (REQUIRED) notice

The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

Automotive Data Solutions Inc. © 2014

beFoRe instaLLation

1- Connect module to computer

2- Login to Weblink account

3- Flash firmware to module (module is not preloaded with firmware)

4- Use accessories accordingly (accessories are sold separately) www.idatalink.com

vehicLe List - 1 oF 1

NOTES

I This fi rmware does not cover the doorlock feature.

Use the OEM remote or an aftermarket one button remote to control the doorlock feature.

The OEM remotes remain functional during runtime.

II The maximum runtime for all 2013 models is 20 minutes. The remote start sequence can only be done once. To perform another remote start sequence, start and stop the vehicle or wait 1 hour.

Fusion STD key AT

Fusion Hybrid STD key AT

Fusion PTS AT

Fusion Hybrid PTS AT

MKZ PTS AT

MKZ Hybrid PTS AT

Page 2 oF 14

DOC.: #16348

• 20140908

FEATURES

13-14 1 • • • • • • • • •

13-14 1 • • • • • • • • •

13-14 1 • • • • • • • • •

13-14 1 • • • • • • • • •

13-14 1 • • • • • • • • •

13-14 1 • • • • • • • • •

Automotive Data Solutions Inc. © 2014 OEM-AL(RS)-FM6-[ADS-ALCA]-EN www.idatalink.com

BOX CONTENTS

MODULE

WHITE

WHITE

WHITE

BLUE

3

4

5

6

1

2

3

4

5

6

7

1

2

1

2

3

1

2

3

A

B

C

D

BOX CONTENTS - 1 OF 1

6 PIN WHITE CONNECTOR

F

E

PROGRAMMING

BUTTON

LED 1


10

9

8

7

6

3

2

5

4

1

2

1

4

3

BLACK

BLACK

DATA PORT

(WEBLINK, RF, TELEMATIC)


3 PIN BLUE CONNECTOR

4 PIN BLACK CONNECTOR

10 PIN BLACK CONNECTOR

Page 3 oF 14

DOC.: #16348

• 20140908

DATA CABLE 1

DATA CABLE 2

WEBLINK CABLE (required accessory sold separately)

WEBLINK CABLE

MODULE

DATA PORT

4 PIN BLACK CABLE

Automotive Data Solutions Inc. © 2014 OEM-AL(RS)-FM6-[ADS-ALCA]-EN

COMPUTER

USB PORT www.idatalink.com

Fusion /

Fusion Hybrid

STD key

AT

Fusion /

Fusion Hybrid

PTS

AT

MKZ /

MKZ Hybrid

PTS

AT

13-14

13-14

13-14

WIRE DESCRIPTION

CanH 1

CanL 1

CanH 2

CanL 2

12V

Ground

CanH 1

CanL 1

CanH 2

CanL 2

12V

Ground

CanH 1

CanL 1

CanH 2

CanL 2

12V

Ground

TYPE 1 - WIRE CHART - 1 OF 1

OBDII

OBDII

OBDII

OBDII

OBDII

OBDII

OBDII

OBDII

OBDII

OBDII

OBDII

OBDII

OBDII

OBDII

OBDII

OBDII

OBDII

OBDII

24 pin

24 pin

24 pin

24 pin

24 pin

24 pin

24 pin

24 pin

24 pin

24 pin

24 pin

24 pin

24 pin

24 pin

24 pin

24 pin

24 pin

24 pin

Black

Black

Black

Black

Black

Black

Black

Black

Black

Black

Black

Black

Black

Black

Black

Black

Black

Black

WIRE COL

20 Blue

19 White

23 Gray/Orange

22 Purple/Orange

13 White/Red

01 Black/Gray

20 Blue

19 White

23 Gray/Orange

22 Purple/Orange

13 White/Red

01 Black/Gray

20 Blue

19 White

23 Gray/Orange

22 Purple/Orange

13 White/Red

01 Black/Gray

MODULE LOC

(DATA) OBDII module, driver side dash




(+)

(-)

OBDII module, driver side dash






(+)

(-)







(+) OBDII module, driver side dash

(-) OBDII module, driver side dash

Page 4 oF 14

DOC.: #16348

• 20140908

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

COMPONENT LOC


MODULE

A

B

C

D

A

B

C

D

3

4

1

2

5

6

5

6

7

3

4

1

2

1

2

3

1

2

3

E

3

4

1

2

F

E DATA

01 GRAY/YELLOW (NC)

02 GRAY/RED (NC)

03 GREEN/YELLOW (NC)

04 GREEN/RED (NC)

05 BLUE/YELLOW (NC)

06 BLUE/RED (NC)

01 PINK (NC)

PINK/BLACK (NC)

03 ORANGE (NC)

05 ORANGE/BLACK (NC)

06 BROWN/YELLOW - CANL

BROWN/RED - CANH

01 YELLOW (NC)

02 YELLOW/RED (NC)

03 YELLOW/BLACK (NC)

01 WHITE (NC)

02 WHITE/RED (NC)

03 WHITE/BLACK (NC)

STEP 1

01 BLUE/WHITE (NC)

02 WHITE (NC)

03 BLACK - GROUND

04 RED - 12V (+)

SELECT ONE OF THE TWO OPTIONS

WITHOUT A COMPATIBLE ACCESSORY:

CONNECT 12V AND GROUND FROM

MODULE TO VEHICLE.

OR

WITH A COMPATIBLE ACCESSORY:

SEE THE COMPATIBLE ACCESSORIES

PAGE FOR DETAILS.

F

3

4

1

2

7

8

5

6

3

4

1

2

9

10

DATA CABLE

GROUND

12V (+)

01 GREEN/BLACK (NC)

02 BLUE/BLACK (NC)

03 RED/WHITE (NC)

04 BROWN (NC)

05 PURPLE/YELLOW (NC)

06 PURPLE/BLACK (NC)

07 WHITE (NC)

08 BLACK/WHITE (NC)

09 GREEN (NC)

10 PURPLE/WHITE (NC)

TYPE 1 - WIRING DIAGRAM - 1 OF 1

STEP 2

STEP 3

CONNECT TEMPORARILY

SEE PROGRAMMING PROCEDURE

CANL 1 - 19

CANH 1 - 20

CONNECT TO VEHICLE

SEE PROGRAMMING PROCEDURE

CANL 2 - 22

CANH 2 - 23

GROUND (-) - 01

12V (+) - 13


Page 5 oF 14

DOC.: #16348

• 20140908

OBDII MODULE, DRIVER SIDE DASH

BLACK

13

24

12

23

11

22

10

21

9

20

8

19

7

18

6

17

5

16

4

15

3

14

2

1 www.idatalink.com

01

02

OFF ACC

START

STOP

03 Wait, LED 1 will turn solid RED.

04

05

CONNECT every wire shown in STEP 1 and

STEP 2 of the wiring diagram.

Set ignition to ON position.

MODULE PROGRAMMING PROCEDURE - 1 OF 1

07

OFF ACC ON START

Set ignition to ON position.

ENGINE

START

STOP

08

Wait, LED 1 will turn solid GREEN for 2 seconds.


Set ignition to OFF position.

ENGINE

STOP

Wait, LED 1 will fl ash GREEN rapidly.

09

10



ENGINE

START

STOP

Module Programming Procedure completed.

06 DISCONNECT every wire shown in STEP 2 and

CONNECT every wire shown in STEP 3 of the wiring diagram.


Page 6 oF 14

DOC.: #16348

• 20140908 www.idatalink.com

>>

01

NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming.

>>

Time restriction. Complete next step within 7 seconds.

VALET MODE PROGRAMMING PROCEDURE - 1 OF 1

To exit valet mode: repeat steps 1 to 5.

02

OFF ACC

ENGINE

START

STOP

03

Cycle ignition ON fi ve times [5x OFF/ON] rapidly.

Wait, LED 1 will turn solid RED for 2 seconds.

04



START

STOP

05 Valet Mode Programming Procedure completed.


Page 7 oF 14

DOC.: #16348


>>

>>

>>

It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the

Module Navigation will drain vehicle battery.

To exit the Module Navigation at any time:

Follow STEP 13.

Module must be programmed to the vehicle.

04

05

Use the Module Navigation Chart on the next page.

06

01



ENGINE

STOP

02

TO ACCESS THE MENUS: Press and hold programming button until LED 1 turns solid

GREEN.

07

08

03

[X]

IN THE MENUS: Press the programming button as many times as the menu number indicates. LED 1 will fl ash GREEN an equal amount of times continuously.

Automotive Data Solutions Inc. © 2014

09

MODULE NAVIGATION PROCEDURE - 1 OF 1

TO ACCESS THE OPTIONS: Press and hold programming button until LED 1 turns solid

RED.

10

[Y]

IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED 1 will fl ash RED an equal amount of times continuously.

TO ACCESS THE SETTINGS: Press and hold programming button until LED 1 turns solid

GREEN.

11

12

[Z]

LED 1 will flash GREEN as many times as the current (or default) setting number, continuously.

13

[Z]

IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED 1 will fl ash GREEN an equal amount of times continuously.

To return to the MENUS: exit the Module

Navigation and redo the Module Navigation

Procedure.

14

>>

OEM-AL(RS)-FM6-[ADS-ALCA]-EN

Page 8 oF 14

DOC.: #16348

• 20140908

To save and return to the OPTIONS: Press and hold programming button until LED 1 turns solid RED.

[Y]

LED 1 will fl ash RED as many times as the current option number continuously.

Configure every other setting and proceed to step 13.

MANDATORY: EXIT MODULE NAVIGATION.

Press and hold programming button for 7 seconds. LED 1 will fl ash RED rapidly. Release programming button. LED 1 will turn OFF.

Module navigation completed.

Failure to exit the Module Navigation will drain vehicle battery.

www.idatalink.com

moDuLe navigation chaRt - 1 OF 1 Page 9 oF 14

DOC.: #16348

• 20140908 moDuLe navigation chaRt: notes

I Default settings are listed in bold.

II Make sure the option is covered on the vehicle before attempting to change the setting.

01 CONFIGURATION

*Vehicle will shutdown when a door is opened.

**The maximum runtime for 2013 models is 20 minutes.

02-07 Technical Support only

01-04 N/A

05 TAKEOVER

06 N/A

07 FACTORY KEYLESS RS SEQUENCE

08 MODULE RUN TIME

09-12 N/A

01 N/A

02

03

04

05

06

07

08

01

01

01

01

02

01

01

02

03

04

01

05 MIN

10 MIN

15 MIN

25 MIN**

30 MIN**

35 MIN**

15 min

N/A

N/A

N/A enabLe

DISABLE*

N/A

DISABLE

N/A

LOCK + UNLOCK + LOCK

LocK + LocK + LocK

03 MIN


Remote staRteR eRRoR coDes - 1 OF 1

Remote staRteR eRRoR coDes: notes

I WARNING: The following applies only when the parking lights are connected and supported by the system.

II After a remote starter failure, the parking lights will fl ash

[X] number times to indicate an error code. See table.

03

04

05

06

07

08

[X] numbeR oF PaRKing Light FLashes

Foot brake is ON.

Hood is open.

Engine tach signal is lost.

System is in Valet Mode.

Vehicle is moving (VSS).

Glow plug timeout error.

Page 10 oF 14

DOC.: #16348

• 20140908


moDuLe Diagnostics - 1 OF 1 test moDuLe

I DURING PROGRAMMING

II DURING REMOTE START

III WITH IGNITION OFF

Flashing RED

Solid RED

Flashing GREEN

Solid GREEN then OFF

OFF

Flashing RED

Solid RED

Flashing GREEN


OFF

Flashing RED

Solid RED

Flashing GREEN


OFF

Missing/wrong information from fi rmware or vehicle.

Module waiting for more vehicle information.

Additional steps required to complete module programming.

Module correctly programmed.

No activity or module already programmed.

Module incorrectly programmed.

Module incorrectly programmed.

Module correctly programmed and operational.

Reset in progress.

Invalid ground when running status from remote starter.

Module incorrectly programmed or connected.

Module not programmed. Waiting for more vehicle information.

False ground when running status from remote starter.

Reset in progress.

Module at rest and ready for a remote start sequence.

Page 11 oF 14

DOC.: #16348

• 20140908


01

02

03

04

Disconnect all connectors from module except the BLACK 4-PIN connector.

07

MODULE RESET PROCEDURE - 1 OF 1

Reconnect all connectors.

Disconnect the BLACK 4-PIN connector.

08

Repeat programming procedure.

PRESS AND HOLD programming button while connecting the BLACK 4-PIN connector.

Wait, LED 1 will flash RED. RELEASE programming button.

LED 1 will turn RED for 2 seconds.

>> Failure to follow procedure may result with a

DTC or a CHECK ENGINE error message.

05

06 Module RESET completed.


Page 12 oF 14

DOC.: #16348


TAKEOVER PROCEDURE - 1 OF 1

>>

01

All vehicle doors must be closed and locked prior to remote start sequence.

Press unlock on OEM or aftermarket remote or request switch.

02

OFF ACC

ENGINE

START

STOP

03

DO NOT PRESS BRAKE PEDAL. Set ignition to

ON position. Wait 2 seconds for key validation.

Press and release BRAKE pedal.

04

Take over procedure completed.

>> Failure to follow procedure will result in vehicle engine shutdown.


Page 13 oF 14

DOC.: #16348


¨

¨

14

15

¨

¨

6

7

8

¨

¨

5

¨

¨

9

10

11

12

13

¨

¨

4

1

2

3 instaLLation checKList - 1 OF 1 Page 14 oF 14

DOC.: #16348

• 20140908 checKList

WARNING: Vehicle engine will start many times. Test in a well ventilated area.

Close all vehicle doors, hood and trunk.

Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.

Question 1: Does the vehicle remote start?

YES: Go to next step.

NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.

Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.

Question 2: Does the vehicle shut down?


NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.

RAP Shutdown test

Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?


NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.

Open hood.

If not already installed, affi x the mandatory orange warning sticker under the hood and proceed to next step.


Question 4: Does the vehicle remote start?

YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.

NO: Go to next step.

Close hood.

Enter vehicle and close the doors.


Wait for the vehicle to start.

Press brake pedal.

Question 5: Does the vehicle shut down?


NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.

Exit vehicle.

Installation checklist completed.


INSTALL GUIDE OEM-AL(RS)-FM6-[ADS-ALCA]-EN

instaLL guiDe

OEM-AL(RS)-FM6-[ADS-ALCA]-EN

Document numbeR

Revision Date

20140908

FiRmwaRe

OEM-AL(RS)-FM6-[ADS-ALCA] haRDwaRe

ADS-ALCA accessoRies

ADS-USB (REQUIRED) notice

beFoRe instaLLation

Related manuals

Idatalink

ADS-ALCA

Idatalink

ALCA

Firstech, LLC.

FT-DC2-S

Idatalink

BLADE-DL-TL6-EN

Idatalink

COM-BLADE-AL

idatastart

HC2352AC

Firstech

FT-DC2-S

Idatalink

COM-AL(RS)-TL2-EN

Idatalink

iDataStart VWX000A