advertisement
IMMERSIVE SOUND LED LCD HDTV with Integrated Sound Projector
MODELS
154 Series
164 Series
265 Series
BASIC OWNER’S GUIDE
This manual provides basic connection, setup, and operating instructions. Please visit our website at www. Mitsubishi-tv.com to view or download a detailed owner’s guide that fully describes the features of this TV. Follow the Support link to the Product Documents page.
•
•
•
•
-
-
For questions:
Visit our website at www.mitsubishi-tv.com.
E-mail us at [email protected].
Call Consumer Relations at 800-332-2119 for operational or connection assistance.
For information on System Reset, please see the back cover.
To order replacement or additional remote controls, visit our website at www.mitsuparts.com or call
800-553-7278.
265 Series.
IR emitter cables for NetCommand home-theater control are available for purchase from
Mitsubishi. Call 800-553-7278 and request either part number 242D483020 (two-ended cable) or part number 299P254020 (four-ended cable).
®
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
WARNING: This product shall be connected to a MAINS socket outlet with a protective earthing connection.
MAINS DISCONNECTION: The mains plug is used as the disconnect device. The mains plug shall remain readily operable.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm.
TV WEIGHT: This TV is heavy. Exercise extreme care when lifting or moving it. Lift or move the TV with a minimum of two adults. To prevent damage to the TV, avoid jarring or moving it while it is turned on. Always power off your TV, unplug the power cord, and disconnect all cables before moving it.
Note: Features and specifications described in this owner’s guide are subject to change without notice.
Custom cabinet installation must allow for proper air circulation around the television.
NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER IS
PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S ATTEN-
TION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES
GUIDELINES FOR THE PROPER GROUNDING AND, IN PARTIC-
ULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CON-
NECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS
CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL.
Children and TV Viewing
The American Academy of Pediatrics discourages television viewing for children younger than two years of age.
For assistance call 1(800) 332-2119
FCC Declaration of Conformity
Product:
Models:
LCD Flat Panel HDTV
LT-55154
LT-40164, LT-46164, LT-55164
LT-46265, LT-55265
Responsible
Party:
Mitsubishi Digital Electronics
America, Inc.
9351 Jeronimo Road
Irvine, CA 92618-1904
Telephone: (800) 332-2119
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by Mitsubishi could cause harmful interference and would void the user’s authority to operate this equipment.
TV Software
Do not attempt to update the software of this TV with software or USB drives not provided by or authorized by Mitsubishi Digital Electronics America, Inc. Nonauthorized software may damage the TV and will not be covered by the warranty.
Contents
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
Setting Up and Using TV Inputs
. . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
Connection Types and Audio/Video Quality
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix A: Programming the Remote Control
Trademark and License Information
. . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
Cleaning Recommendations
Normally, light dusting with a dry, non-scratching duster will keep your TV clean. If cleaning beyond this is needed, please use the following guidelines:
First, turn off the TV and unplug the power cord from the power outlet.
Occasionally clean dust build-up from the air-intake grilles on the back and sides of the TV. Clean using a vacuum cleaner with a brush attachment.
Top and Sides of the TV
• Gently wipe down your TV with a soft, non-abrasive cloth such as cotton flannel, microfiber, or a clean cloth diaper, lightly moistened with water. Dry with a second dry, soft, non-abrasive cloth.
• For oily dirt, add a few drops of mild liquid detergent, such as dishwashing detergent, to the water used to moisten the cloth. Rinse with a second cloth moistened only with water. Dry with a third dry, soft, non-abrasive cloth.
Screen
•
•
•
IMPORTANT
DO NOT apply any type of liquid to the surface of the TV screen.
Use only a soft, dry cloth to clean the LCD screen. Do not use any liquids.
Wipe the screen gently with an up and down motion.
Clean the entire screen evenly, not just sections of the screen.
General Cleaning Precautions
•
•
•
•
•
DO NOT allow liquid to enter the TV through the ventilation slots or any crevice.
DO NOT use any strong or abrasive cleaners, as these can scratch the surfaces.
DO NOT use any cleaners containing ammonia, bleach, alcohol, benzene, or thinners, as these can dull the surfaces.
DO NOT spray liquids or cleaners directly on the
TV’s surfaces.
DO NOT scrub or rub the TV harshly. Wipe it gently.
For assistance call 1(800) 332-2119
4
Important Safety Instructions
Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
E XAMP LE OF ANT E NNA G R OUNDING
G R OUND C LAMP
E LE C T R IC
S E R V IC E
E QUIP ME NT
NE C — NAT IONAL E LE C T R IC AL C ODE
ANT E NNA
LE AD IN WIR E
ANT E NNA
DIS C HAR G E UNIT
(NE C AR T IC LE 810-20)
G R OUNDING
C ONDUC T OR S
(NE C AR T IC LE 810-21)
G R OUND C LAMP S
P OWE R S E R V IC E G R OUNDING
E LE C T R ODE S Y S T E M
(NE C AR T 250, P AR T H)
Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.
Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
If Your TV Gets Damaged
Crystalline liquid may leak from the LCD panel and broken glass may be scattered.
CAUTION: The crystalline liquid is toxic. Avoid
contact with your skin, eyes, or mouth. DO NOT touch the broken glass or crystalline liquid. DO NOT get glass fragments or crystalline liquid into eyes or mouth.
Should either contact your eyes or mouth, rinse the contacted area thoroughly with water and consult your doctor.
Disposal of Your TV
The LCD panel contains a small amount of crystalline liquid which is toxic and should not be touched.
DO NOT dispose of the TV with general household
waste. For disposal or recycling information, contact your local authorities or the Electronic Industries Alliance at www.eiae.org.
For assistance call 1(800) 332-2119
Stand Installation
•
•
CAUTION
Using this TV with other than the authorized accessories may cause the TV to become unstable, which can cause damage to the product or possible injury.
At least TWO PEOPLE are required to install the stand. Support the TV near the corners as shown. Failure to follow these recommendations may result in personal injury and damage to the product.
Note
•
40- or 46-inch TV:
•
If planning to wall-mount the TV, there is no need to install the stand.
55-inch TV:
The TV comes from the factory with the stand pre-installed.
Required: Phillips Screwdriver
5
1
1
on back of stand
Back
2
2
BACK
3
3
DO support the TV under the corners.
DON’T place your hand where it can get caught under the TV.
DON’T place your hand where it can get caught between the TV and stand.
TV in protective wrapping
CAUTION.
Place the with the extension pieces facing away from the TV.
Otherwise, the TV will be damaged in transit.
Protect the TV and
TV
TV
Extension pieces on stand must face out, away from TV.
For assistance call 1(800) 332-2119
6
Wall-Mounting
To order a wall-mount kit, please contact Peerless Industries, Inc. at (800) 473-3753 or visit www.peerlessmounts.com. Order wall-mount kit model
ST650.
To order a wall-mount kit from Mitsubishi Digital Electronics America, Inc., please visit www.mitsuparts.com or call (800) 553-7278.
Complete installation instructions are included with the kit.
Stand Removal Prior to Wall-Mounting
CAUTION
At least TWO PEOPLE are needed to safely remove the stand. Have one person hold the TV while the other person removes the stand. Failure to follow these recommendations may result in personal injury and damage to the product.
Note
•
•
55-inch TV:
Remove the factory-installed stand prior to wall-mounting.
40- or 46-inch TV:
If you installed the stand for table-top use, follow these instructions to remove it prior to wall-mounting the TV.
1.
2.
3.
4.
5.
Disconnect the TV’s AC power cord from the AC power outlet.
Spread the protective sheet that was wrapped around the TV on a flat, even surface, such as a sturdy table. The protective sheet will help prevent damage to the display.
IMPORTANT: To avoid damaging the screen, make sure there are no foreign objects under or on top of the protective sheet.
Position one person on each side of the TV (left and right sides). Have each person firmly grasp their side of the TV and gently place it face down on the protective sheet with the display stand hanging over the edge of the table. See the illustration to the right.
Use a magnetic philips screwdriver to remove the stand screws from the recessed holes (see illustration to right).
Note: A regular screwdriver can be used with a separate magnetic pick-up tool.
While one person holds the TV with both hands, have the other person grasp the stand (see illustration to the right) and remove the stand by pulling it away from the TV in the direction of the large arrow shown in both illustrations.
Protective sheet
Table
Protective
Sheet
TV
55-inch TVs
(6 screws)
Stand
40- and 46-inch TVs
(4 screws)
Pull stand to remove.
Service and Customer Support
Service
If you are unable to correct a problem with your TV, consult Mitsubishi Consumer Relations at (800) 332-
2119.
• DO NOT adjust any controls other than those described in this Owner’s Guide.
• DO NOT remove the protective back cover of your TV.
For assistance call 1(800) 332-2119
Customer Support
• To order replacement or additional remote controls, visit our website at www.mitsuparts.com or call (800) 553-7278.
• For questions:
-
-
-
Call Consumer Relations at 800-332-2119.
E-mail: [email protected]
Website: www.mitsubishi-tv.com
1
Basic Setup and Operation
Package Contents
Please take a moment to review the following list of items to ensure that you have received everything.
Remote Control
1.
Installing the Remote Control
Batteries
Remove the remote control’s back cover by gently pressing in the tab and lifting off the cover.
2.
3.
Load the batteries, making sure the polarities
(+) and (-) are correct. For best results, insert the negative (-) end first.
Snap the cover back in place.
Two AA Batteries
AA
AA
7
1
Basic Owner’s Guide
The remote control requires two
AA batteries.
Quick Setup Guide
Product Registration
Card
Power Cord
Cable Ties
Stand Screws (40- and
46-inch TVs only)
265 Series. Calibration
Microphone
2
1.
Before You Begin
Review the important safety, installation, and operating information at the beginning of this book.
2.
Choose a location for your TV.
•
See the stand-installation or wall-mounting requirements starting on page 5.
• Allow at least four inches of space on all sides of the TV to help prevent overheating. Overheating may cause premature failure of the TV.
• Avoid locations where light may reflect off the screen.
3.
4.
Install the batteries in the remote control.
Plug the TV into an AC power outlet.
TV power connection
For assistance call 1(800) 332-2119
8
1. Basic Setup and Operation
Remote Control
Sleep Timer, page 21
Number/letter keys
Pass-code entry, page
29
Adds a separator in digital channel numbers. Clears some menu entries.
MUTE Mutes the TV speakers.
TOOLS Displays shortcuts for the number keys.
Press to check if shortcuts are available for the current device.
VOL Controls volume of TV speakers.
CH
PAGE
Changes channels; moves to another page in a menu or list.
ENTER
Selects a channel number or menu item.
Navigation and adjustment controls
GUIDE ChannelView listings, page 17.
INFO TV status or TV help.
(PAUSE) Freezes a broadcast TV picture.
Record/Playback controls for external devices. Additional setup is required.
Emitter-Bulb End
TV CAB/SAT DVD AUDIO VCR
Press the key for the device type to control. Leave in TV mode for normal
TV viewing.
Powers TV on or off.
LAST Returns to the previous channel.
FAV
Displays up to nine favorite sources, page 17.
FORMAT Changes picture shape, page 12
INTERNET
Connects to internet content,
INPUT Press to select a TV input,
AUDIO Audio settings, page 25
VIDEO Video settings, page 24
MENU
Displays or clears the TV main menu (page 24). Also steps back one menu.
EXIT
Clears all menus.
265 Series. Special keys for use with NetCommand IR control.
See the detailed owner’s guide at www.mitsubishi-tv.com.
The TV’s remote control can operate other audio/video devices using any of these methods:
• Program the remote control for the device.
• Set up HDMI Control for HDMI devices compatible with the TV.
• 265 Series. Perform NetCommand setup of device keys.
See the detailed owner’s guide at www.mitsubishi-tv.com for information.
For assistance call 1(800) 332-2119
First-Time Power-On
1.
Press the
TV key to
ensure that the remote control is in
TV mode.
TV
2.
Aim the emitter (bulb) end of the remote control at the TV and press the
POWER key
. Wait for the
Welcome screen.
3.
If you wish to change the menu language to Español, press .
TV
1. Basic Setup and Operation
Welcome Screen Energy Options
•
•
Mitsubishi recommends the Home setting, which uses power within ENERGY STAR® guidelines.
The Retail setting looks best under bright lighting. In this mode, the TV uses power in excess of ENERGY STAR guidelines.
This table compares energy choices offered in the
Welcome screen.
Home
Picture Mode Bright
Backlight Level
Reduced
Brightness
Retail
Brilliant
Full Brightness
4.
Press to move to the energy-mode selections.
Select Home.
5.
Press to highlight
EXIT
.
Press ENTER to clear the menu.
Setting Up and Using TV Inputs
Using the ANT (Antenna) Input
If using an antenna or direct cable service (no cable box), connect the incoming coaxial cable to the TV’s
You must perform a channel scan to enable recep-
tion of digital channels. If you skip this step, the TV
will receive only analog channels. The channel scan will search for high-definition and standard-definition channels available in the local area.
Memorizing Channels with Channel Scan
For the ANT input
To start channel memorization
1.
Power on the TV.
2.
Press
MENU and open the Setup > Channel menu.
First press to navigate to the Setup icon, then use to highlight the Channel icon.
Start channel memorization from the Setup > Channel menu.
3.
4.
5.
6.
Press to enter the menu.
Highlight Ant Air if connected to an over-the-air antenna. Highlight
Ant
Cable for service over direct cable
(no cable box). Press ENTER to add a check.
For first-time setup, highlight
All
channels. To scan for channels not already in memory, highlight
New
only. Press ENTER to add a check.
Highlight Scan and press ENTER.
Channel memorization may take up to 15 minutes to complete.
To stop channel memorization before completion,
press CANCEL.
9
For assistance call 1(800) 332-2119
10
1. Basic Setup and Operation
Setting Up and Using TV Inputs, continued
Setting Up Other Inputs
1.
2.
3.
Power on the TV.
Power on the devices to ensure detection.
Connect one device to the TV, making note of the
TV input jack.
The TV will display the New Device Found screen if the connection type is detectable.
4.
Highlight the device type in the on-screen list and press
ENTER. The name you select here will appear in the
Input Selection menu.
Selecting an Input to Watch
1.
Press INPUT.
Sample New Device
Found screen.
5.
6.
Press EXIT to close the New Device Found screen.
Repeat steps 3 through 5 for each additoinal device you want to add.
Sample Input Selection menu, antenna input selected
2.
3.
Press to highlight an input icon.
Press
ENTER to switch to the input.
Tuning to Channels on the Antenna Input
•
•
Enter the channel number using the number keys on the remote control and press
ENTER.
For a two-part digital channel, such as 3-1, press 3
•
•
•
•
•
Press CH / to change channels one channel at a time.
Press and hold CH / to speed through channels.
Press LAST to return to the previous channel.
Use the Fav (Favorites) feature to tune to up to nine favorite channels. See page 17.
Press GUIDE to display ChannelView channel listings, highlight a channel number, and press ENTER to tune.
About Auto Input Sensing
•
•
•
This TV’s Easy Connect™ Auto Input Sensing feature detects most input connections automatically. Some exceptions are:
•
A connection on the
ANT input
TV audio outputs (analog and digital)
An HDMI-equipped device that is powered off.
Power on the device first to ensure detection.
Ethernet
Auto Input Sensing for Most Devices
When you first connect a device, the TV will: a. Detect the connected device and automatically switch to it.
b. Prompt you to identify the device type.
c. Repeat these steps for other newly detected devices.
For assistance call 1(800) 332-2119
Basic TV Operation
Picture Settings
1.
To get the best picture under different viewing conditions, set the Picture Mode first before changing other video settings. See page 24 for a description of the options.
a. Press VIDEO.
b. Press until the Picture Mode option displays.
1. Basic Setup and Operation
11
Audio Controls
Changing the Audio Output
To switch from the internal TV speakers to an external sound system:
1.
2.
3.
Press AUDIO.
Press to display the
TV Speakers option.
Press to change.
c. Press to make one of these selections:
Name When to Use
Brilliant
Under bright light
Game
With gaming consoles (inputs named Game or PC only)
Bright
For most daytime viewing
Natural
For most nighttime viewing
2.
3.
4.
Press
Press
to display the name of another adjustment.
to make the adjustment.
Wait a few seconds and the display will clear.
See also these menus:
Menu
Picture > Picture Plus
265 Series. Picture > Perfect
Page
Changing Audio Settings (TV Speakers Only)
1.
2.
3.
Press
AUDIO.
Press to display the name of the adjustment you want. See page 25 for options.
Press to change.
Controlling Sound Volume
•
•
Press
VOL / to adjust the sound level of the TV speakers.
See the full owner’s guide at www.mitsubishi-tv.com for methods of controlling A/V receiver volume.
POWER Indicator
POWER
Key Off
Steady On
Slow Blinking
Fast Blinking
LED Color TV Condition
None
TV is powered off. Normal operation.
Green
TV is powered on. Normal operation.
Green
TV powered off, auto-on TV Timer is set.
Normal operation. TV can be turned on at any time.
Green
Software download in progress (applies only if home network is connected). TV cannot be powered on until complete. Do not unplug the TV during download.
Red/
Yellow
TV may require service.
• Hold power button on front panel for 10 seconds to reset TV.
• If LED continues to flash red and yellow after reset, turn off the
TV and unplug it from the AC power source. Wait one minute and then plug the set back in.
• If LED continues to flash red and yellow, go to www.mitsubishi-tv.com or call 1-800-332-2119 to receive Authorized Service Center information.
You may be asked to count how many times the LED flashes each color to assist in troubleshooting.
For assistance call 1(800) 332-2119
12
1. Basic Setup and Operation
Basic TV Operation, continued
The FORMAT Key and Picture Shape
Repeatedly press the
FORMAT key to cycle through displays available for the current program. The TV will remember the format you last used on each input.
Sample Uses of the FORMAT Key
You can use the FORMAT key to reduce or eliminate black areas at the edges of the picture.
Press
Important
Black bars at the edges of the screen are common in HD pictures. Black bars are not a defect of the TV.
•
•
Black bars are added by broadcasters to fill the 16:9 screen area while preserving the original aspect ratio of the picture.
Your cable box or satellite receiver may also be altering the broadcast picture. If your receiver offers output in native format, try using it with
Mitsubishi picture formats.
Squarish 4:3 image is narrower than the 16:9 screen; unused areas at the sides are filled with black.
Wide 2.35:1 anamorphic DVD image; unused areas at the top and bottom are filled with black (letterbox effect).
Press
Wide Expand mode stretches the picture sideways to fill the screen.
Zoom mode. The picture fills the screen. All four edges are cropped in this mode.
More TV Features
Features covered in this Basic Owner’s Guide include:
Feature
Parental controls (
Lock menu)
TV Clock. Set the TV Clock if you plan to use the
TV Timer (page 27) or ChannelView (page 17).
Page
29
27
Favorite sources
ChannelView channel listings
Changing input names in the
Input Selection menu (
Inputs > Name menu)
Digital camera images and music files
Programming the Remote Control
See the detailed owner’s guide at www.mitsubishi-tv.com for a complete code list.
17
30
Internet video streaming
265 Series. Listening to a wireless audio device with the TV speakers
For assistance call 1(800) 332-2119
•
•
•
See the detailed Owner’s Guide at www.mitsubishi-tv.com for more on the features described here and to learn about other features, including:
•
•
HDMI control (CEC) of other A/V devices
Center and rear channel audio output
Using an external subwoofer
Using the TV with a computer
265 Series.
NetCommand IR control of other A/V devices. Use of NetCommand requires purchase of
IR emitter cables from Mitsubishi.
2
TV Connections
Input and Output Jacks
DIGITAL
AUDIO
OUTPUT
(page 15)
AVR/SURROUND
OUTPUT
(page 26)
Calibration Microphone Input
(265 series, page 23)
CENTER-CH INPUT
SUBWOOFER
OUTPUT
See the detailed owner’s guide at www.mitsubishi-tv.com.
AUDIO
(analog stereo audio input)
Y/VIDEO
(composite video input)
Y/VIDEO Pb Pr
(component video input)
NetC OUT/IR IN
(265 Series.
NetCommand/IR external controller jack. See the detailed owner’s guide at www.mitsubishi-tv.com.)
USB (page 20)
USB (Power Only)
Provides power to TV accessories.
DVI/PC AUDIO INPUT
(page 14)
LAN
(Ethernet, port page 18)
AUDIO
(analog stereo audio) input
Y/VIDEO Pb Pr
(component video input)
ANT
(coaxial antenna input)
Y/VIDEO
(composite video)
HDMI
Auto Input Sensing
The TV’s Auto Input Sensing feature automatically recognizes many connections and prompts you to identify the device type. See page 10.
Cable Routing
Install the supplied cable ties in any of four mounting holes.
HDMI
1
Press the release tab to loosen the cable bundle.
Installing the cable tie
2
Removing the cable tie
Sample cable routing. Secure the cable bundle with the release tab facing out.
For assistance call 1(800) 332-2119
13
14
2. TV Connections
HDMI Device
Mitsubishi recommends using high-speed HDMI cables to connect newer devices incorporating HDMI technology.
Y Pb Pr Component Video Device
Required:
• RCA-type component video cables
• Left/right analog stereo audio cables
HDMI-to-HDMI cable
Any HDMI device
TV
HDMI and Digital Surround Sound
The TV’s HDMI inputs can receive digital surround sound from an HDMI device. Use an HDMI connection if you want to hear digital surround sound from the TV’s internal speaker array.
Component video device
Pb
Pr
L
R
AUDIO
Y
Audio cables
Component video cables
CABLE IN or
SATELLITE IN
Incoming from cable service or satellite dish
TV
Composite Video Device
Required:
• Composite video cable (usually yellow)
• Left/right analog stereo audio cables
DVI Video Device
Required:
• DVI-to-HDMI cable or DVI/HDMI adapter and
•
HDMI cable
Analog stereo cable with mini plugs
TV
L
R
AUDIO OUT
Audio cables
COMPOSITE
VIDEO OUT
Composite video cable
VCR or other device with composite video output
Digital DVI device
AUDIO
OUT
Audio cable
DVI OUT
DVI-to-HDMI cable
TV
L
AUDIO
R Y Pb Pr
For assistance call 1(800) 332-2119
R
AUDIO
L
A/V Receiver
Most setups require either an optical audio cable or analog stereo audio cables. To send audio from TV channels received on the
ANT input or devices connected directly to the TV, you must use one of the connections shown below.
The TV makes all audio available in digital and analog formats:
• Analog audio coming into the TV is available as output in digital stereo format on the
DIGITAL
AUDIO OUTPUT jack.
• Digital incoming audio is available as analog output on the
AVR/SURROUND L and R jacks.
2. TV Connections
15
A/V Receiver with HDMI Output
Required: One HDMI-to-HDMI cable
This option allows you to view content from devices connected to an A/V receiver. The A/V receiver can send audio and video to the TV over a single HDMI cable. You can use an HDMI connection as described here in addition to an audio connection from the TV’s audio output. The optional audio connection allows you to hear, through the A/V receiver, devices connected to the TV only, e.g., an antenna on the
ANT input.
Optical cable
(digital A/V receiver) or
Stereo analog cables
(analog A/V receiver)
HDMI cable
TV
Optional analog or digital audio connection
OPTICAL
INPUT
COAXIAL
INPUT
A/V receiver back panel
A/V receiver with
HDMI output
HDMI OUT
Any connection types
High-definition
DVD player
OPTICAL
AUDIO IN
Cable box
R L
ANALOG AUDIO IN
VCR
DVD player
Y/ VIDEO
For assistance call 1(800) 332-2119
16
2. TV Connections
Antenna or Cable TV Service
Connect the incoming cable to the TV’s
ANT input.
Antenna or
Direct cable (no cable box) or
Cable TV service
IN
OUT Older cable box
Not recommeded. Other connection types provide better quality audio and video.
ANT
VCR or DVD Recorder to an Antenna or Wall Outlet Cable
Required:
1. Video cables
1a. Component video cables (red/blue/green)
or
1b. Composite video cable (usually yellow)
2. Left/right analog audio cables.
3. Two-way RF splitter
4. Two coaxial cables
Note: If your recording device has an analog-only tuner, you must use a digital converter box to enable recording of digital broadcasts.
2.
Composite video cable or
1b.
1a.
R
L
AUDIO OUT
COMPOSITE
VIDEO OUT
COMPONENT
VIDEO OUT
DVD Recorder or VCR
3.
RF Splitter
Incoming cable
ANTENNA
IN
4.
4.
Connection Types and Audio/Video Quality
VIDEO QUALITY
BEST
GOOD
HDMI HDMI-to-DVI
Component
Video
Composite
Video HDMI
BEST
AUDIO QUALITY
GOOD
Digital
Audio
L/R Analog
Audio
For assistance call 1(800) 332-2119
3
TV Features
FAV (Favorites)
The FAV key gives you quick access to favorite program sources. Sources can be channels from the ANT input or devices connected to the TV. You can store up to nine favorites.
Sample Favorites menu. Switch to favorite channels or inputs using number keys.
1.
2.
3.
4.
Press INPUT and switch the TV to the input you want to add. If adding a channel, switch to the ANT input and tune to the channel.
Press the FAV key.
Move the highlight to the number position you want to assign to the channel or input.
Press ENTER.
1.
2.
3.
While watching TV, press the FAV key.
In the
Favorites menu, highlight the channel or input you want to remove.
Press CANCEL.
1.
2.
While watching TV, press the
FAV key.
Press the number key for the channel or input you want.
ChannelView Channel Listings
About ChannelView
ChannelView displays program descriptions sent by broadcasters. This information may be unavailable in some areas.
ChannelView™ shows memorized channels on the ANT input. It displays channel names and program information for digital channels. No program information is displayed for analog channels.
ChannelView allows you to set up three banks of custom channels for convenient access. You can save groups of channels by content (e.g., news, sports, children’s programming) or by
TV user.
Note: You must first set the TV Clock (page 27) to receive
ChannelView listings.
ChannelView “All” channels tab. Programs for the tuned channel are listed on right side of screen.
ChannelView Custom Channel Banks
Select a channel bank to customize.
1.
2.
3.
4.
5.
Press GUIDE to display ChannelView.
Press MENU to move the highlight to the bank header.
Press to select Bank 1, 2, or 3.
With the bank name highlighted, press ENTER to enter setup mode where you can select channels to include in the bank.
Press EXIT when finished with setup.
Using Custom Channel Banks
•
•
•
While watching TV, press
CH / . The TV will tune only to channels stored in the current bank.
1.
2.
3.
4.
To change to a different channel bank:
Press
GUIDE.
Press
MENU.
Press to highlight a bank.
Press MENU to see channels in the bank.
To allow tuning to any channel in memory, select the
All bank.
For assistance call 1(800) 332-2119
17
18
3. TV Features
StreamTV™ Internet Media
Internet services provided by VUDU™ Apps let you access many popular on-line applications. In addition to free content, VUDU’s movie service lets you buy and rent movies through the TV. Visit www.VUDU.com to learn more about available movie titles, prices, and services offered. For a list of recommended routers and switches, see the Support > FAQ section at VUDU.com.
Required for StreamTV internet media:
• Broadband internet service (at least 2 Mbps for SD, 4 Mbps for HD, and 8 Mbps for 1080p HDX)
•
•
Ethernet cable or to connect a 154 series TV wirelessly, an Azurewave AW-NU231 USB wireless adapter.
Computer access to the VUDU.com website (required for initial account activation).
• A credit card for rental and purchase transactions from VUDU’s movie service.
Home Network Setup
Before using StreamTV internet media, you must connect the TV to the internet using one of these methods.
Ethernet Connection
DHCP (automatic)
1.
Connect the TV to your network router with a Category-5 Ethernet cable (not supplied).
Router or modem providing high-speed internet service
Incoming internet cable
IEEE 802.11n-compliant wireless network router providing high-speed internet service
USB wireless adapter
154 Series TV. A USB wireless adapter is required for wireless connection.
3.
Open the Setup > Network menu. After a few moments, detected networks will appear listed on the screen in order of signal strength.
Incoming internet cable
Ethernet cable
LAN
2.
3.
Open the Setup > Network menu to review settings.
Press EXIT to clear the menu.
Manual
1.
2.
3.
4.
5.
6.
Connect the TV to your network router with a Category-5 Ethernet cable (not supplied).
In the Setup > Network menu, highlight Manual and press ENTER.
Press to move to the Connection Data area.
Input the connection data.
After entering connection data, press ENTER to connect.
Change any of the following if needed:
• Default Gateway
•
•
DNS
Subnet Mask
Wireless Connection
•
•
164 and 265 series
models have built-in wireless capabilities and can communicate directly with your wireless router.
154 series
TVs require an Azurewave AW-NU231
USB wireless adapter.
1.
2.
Disconnect the Ethernet cable if present.
For a 154 series TV, connect the USB wireless adapter.
For assistance call 1(800) 332-2119
Setup > Network menu
4.
Highlight the desired network and press ENTER to connect. A check will appear next to the connected network.
Setup > Network menu after connecting. The active network is checked and connection data displays.
5.
If connecting to a secure network, enter the network key or password on the remote control when prompted.
StreamTV™ Internet Media, continued
Using StreamTV Internet Media
After establishing internet connectivity, press the
INTERNET key to display services from VUDU Apps. Press
ENTER to launch an application.
INTERNET
2.
3.
4.
Getting Started with VUDU
Movies
1.
After establishing internet connectivity, press
INTERNET to display offerings from VUDU™.
Select the VUDU movie service.
Browse the VUDU movie catalog and offerings.
When you are ready to rent or buy a movie, you will be prompted to activate your VUDU account.
Follow the on-screen instructions and use a computer to go to www.VUDU.com/activation. A credit card is required for activation.
Once your account is activated, you can rent and buy movies using only the TV and the TV’s remote control.
Specialized Keys for VUDU
INTERNET Displays the VUDU internet menu.
GUIDE
VUDU HOME key
INFO
LAST
VUDU
VUDU
MORE key
BACK key (goes to previous menu)
CANCEL
VUDU backspace (in text-entry screens)
F2
VUDU System menu
EXIT
Exit VUDU
Troubleshooting
If You Are Unable to Connect to the Internet
•
•
•
Check all power and data connections.
If you can reach the internet with a computer or other device on the same internet service used by the TV, consult the router or modem owner’s guide for reset instructions.
If you cannot reach the internet, contact your service provider. You may be asked for network information such as the TV’s IP address. Go to the
Setup > Network menu to see connection data.
For Further Assistance
•
•
•
If you are having trouble connecting your TV or accessing internet applications, contact Mitsubishi
Customer Care at 1-800-332-2119.
If you are having difficulty with your VUDU account, contact VUDU Customer Care at www.VUDU.com/support.
See more troubleshooting tips in Appendix B.
3. TV Features
19
Wireless Audio Playback
164 and 265 Series. The TV’s built-in speaker array can play audio from a handheld device using Bluetooth®
A2DP (stereo audio) wireless technology.
Pairing the TV with an Audio Device
1.
2.
Turn on the wireless device you wish to use for playback. Turn off all other wireless devices in the area as the TV can pair with only one device at a time.
Press INPUT to display the Input Selection menu.
Bluetooth® icon in Input Selection Menu
3.
4.
5.
Highlight the Bluetooth icon and press ENTER.
Pair your device with the TV and then connect. Some devices pair and connect automatically, while others require you to enter the TV pass code displayed.
Use keys on the TV’s remote control to control playback. Not all keys work for all devices.
Skip a track
(PAUSE)
(STOP)
(REVERSE)
(PLAY)
(FORWARD)
Resetting Bluetooth Pairing or Connection
Perform this reset if the audio device does not connect properly to the TV.
1.
2.
3.
4.
5.
If the audio device has been previously paired with the TV, delete the TV from the device’s paired list.
Go to the TV’s
Inputs > Name menu and highlight the Bluetooth icon. Press
ENTER to select Off.
Press EXIT.
Go to the
Inputs > Name menu and highlight the
Bluetooth icon. Press ENTER to select On.
Press EXIT.
Tips for Wireless Playback
•
•
•
•
Selecting the
Bluetooth icon at a later time will reconnect the TV to the paired device.
If the paired device is not available, the TV will accept pairing from a different device.
Once connection is lost, the TV will power off after five minutes without receiving a signal.
To clear a paired device, turn off the
Bluetooth icon
(
Inputs > Name menu) or pair the TV with a different device.
For assistance call 1(800) 332-2119
20
3. TV Features
Camera Images and Music Files
USB Media Player Menu
USB Media Setup Menu
Use the USB Media Setup menu to set up play of a slide show or playlist.
USB Media menu, Photos option selected
Displaying the Menu
Note: Back up the data on your USB drive before connecting it to the TV. Mitsubishi is not responsible for any file damage or data loss.
1.
Connect your USB drive to the TV’s USB port.
The
USB Media Player menu displays while files are being read. Wait until icons appear in the menu before continuing.
The TV can read photo and music files from the USB port.
Notes on Using the USB Port
•
•
•
The TV ignores all commands while reading files.
Large files or high-capacity storage devices may take a long time to display.
Some manufacturers’ devices may be incompat-
-
ible with the TV. If the TV is unable to display your photos, you can:
Transfer files to a different USB device.
Use your digital camera’s composite video output.
Picture Files Compatible with the USB Port
• Still images recorded using the Exchangeable Image
File Format, version 2.1 (EXIF 2.1) standard for digital still cameras and Design Rules for Camera File Systems version
1.0 (DCF 1.0)
• Some images opened and resaved on a computer may not play back or may not display in the thumbnail list.
• Full file path names can be no longer than 50 characters and must end in a .jpg extension.
For assistance call 1(800) 332-2119
IMPORTANT
Always stop playback with
( STOP) or change to a
different TV input before disconnecting your USB device.
Using the Photos and Audio
Menus
Use these keys with your photo and audio files.
Key
or
ENTER
For Photo or Audio Tracks
Plays the slide show or playlist starting from the highlighted item.
Pauses a slide show or playlist.
Stops a slide show or playlist.
GUIDE
INFO
•
•
•
•
Highlights the first or last item on the current page.
Skips to the previous or next item during play.
Displays the previous or next page of items.
Skips immediately to the previous or next item during play.
Rotates an image clockwise in 90˚ increments.
Displays the item name during play. Press
EXIT to clear.
Clears on-screen displays.
EXIT
MENU
Displays the main menu; stops play.
INPUT
Displays the Input Selection menu; stops play.
Camera Images and Music Files continued
Photos and Moving Video as Composite Video
Connect the camera to the TV using a composite video cable and control the slide show or movie through the camera. The display resolution will be standard-definition (480i).
1.
2.
3.
Refer to the owner’s manual supplied with the camera for instructions needed for this setup.
Set the camera’s output signal type to
NTSC and put the camera into playback mode.
With the camera still turned on, connect your digital camera’s composite video cable (usually yellow) to the TV’s Y/VIDEO jack. To hear audio, connect the camera’s audio output cable to the AUDIO L jack.
Optional
Audio Cable
TV
3. TV Features
21
Sleep Timer
The Sleep Timer turns the TV off after the length of time you set. To set the TV to turn on at a certain time of day, see the
Setup > Timer menu on page 27.
Setting the Sleep Timer
1.
Press SLEEP.
2.
3.
Press
SLEEP additional times to increase the time in
30-minute increments up to the maximum of 120 minutes.
Press EXIT or wait five seconds without pressing any keys for the message to clear.
Viewing or Changing the Sleep Timer
1.
Press
SLEEP to display the on-screen message.
2.
Press SLEEP additional times to change the time before the TV powers off. To cancel the Sleep
Timer, press SLEEP repeatedly until OFF is displayed.
Camera connection using a composite video cable
4.
5.
6.
When the
New Device Found screen displays, assign the name
Camcorder.
Press EXIT to close the New Device Found screen.
Highlight the icon for the camera input and press
ENTER.
7.
If viewing photos, advance through the images manually or set the camera to advance automatically.
8.
If viewing photos, control the slideshow from the camera. Advance through the images manually or check if the camera can advance automatically.
For assistance call 1(800) 332-2119
22
3. TV Features
Sound Projector
Positioning the TV
The TV’s built-in speaker array can be set up to reflect sound off the room walls to create a surround sound effect.
•
•
Center the seating area in front of the TV and at least six feet away.
Arrangements that give good results:
2.
Enter the room dimensions and layout information requested in the screen. To change measurements, press or enter numbers using the remote control’s keypad.
•
If the room is an odd shape, locate the TV to take best advantage of wall reflections.
•
Avoid locations that may distort sound reflections.
3.
4.
Press EXIT to exit and save settings.
Play some sample audio to check sound quality.
If further adjustment is needed, use the Custom menu as described next.
Custom Menu
Use the
Custom menu after defining the room layout.
1.
From the
Sound > SoundPro menu go to the
CUSTOM menu.
Connecting the TV
To hear digital surround sound, the TV must be connected to a digital surround sound source. The surround sound source can be on an HDMI input or the
ANT input (for some digital broadcasts). Other stereo connections will provide Dolby Pro Logic surround sound.
Manual Setup
Manual setup is available for all models.
Note: If you have already performed Auto setup, any manual adjustments will erase all settings created during Auto setup.
1.
Press MENU and go to Sound > SoundPro.
2.
Position yourself in your usual viewing location.
Remain in this position, looking at the TV, while making the following adjustments.
Controls in the SoundPro > Custom menu adjust the
TV’s sound output.
For assistance call 1(800) 332-2119
Sound Projector, continued
3.
Adjusting Beam Angles
a. Adjust Center Beam Angle until sound is about equal in both ears.
b. Adjust Left Beam Angle to maximize sound heard from the front left side.
c. Adjust Right Beam Angle to maximize sound heard from the front right side.
d. Adjust Left Surround Beam Angle to where the sound seems to come from the left rear side. If this cannot be achieved, make the setting the same as that for Left Beam Angle.
e. Adjust Right Surround Beam Angle to where the sound seems to come from the right rear side. If this cannot be achieved, make the setting the same as that for Right Beam Angle.
4.
Adjusting Levels
a. Adjust Center Level to the mid level.
b. Adjust the following levels one at a time so that each one sounds about the same as the center level:
Left Level
Right Level
Left Surround Level
Right Surround Level
c. Check all sound levels by quickly switching between them using .
d. Readjust individual levels in small increments and recheck as above until all sound levels seem about the same.
3.
4.
5.
Resetting Angle and Level Values in the
Custom Menu
1.
2.
Press
EXIT to clear all menus.
Press MENU. Go to the Sound > SoundPro menu and press ENTER.
Change any setting (e.g.,
TV Location).
Press EXIT to clear all menus.
Press
MENU. Go to the Sound > SoundPro menu and press
ENTER.
6.
7.
Enter the correct values for the room layout.
Return to the
CUSTOM menu to adjust angles and levels.
Auto Setup
265 Series
This section describes auto-setup available with 265 series
TVs. Auto setup uses the included calibration microphone.
1.
2.
Power on the TV and external subwoofer, if any.
Plug the microphone cable into the TV’s INPUT 2 left audio jack.
3. TV Features
3.
4.
Place the microphone as described in the guidelines.
Press MENU and go to Sound > AutoSP.
23
5.
Highlight
START and press ENTER.
6.
7.
Quietly exit the room right away. The calibration sequence may be loud. Wait for completion of setup before returning to the room.
Play some sample audio material to check the sound quality.
Note: Do not perform manual adjustments after running Auto setup.
8.
Store the microphone out of direct sunlight and away from heat.
Microphone Placement
TV
6 ft. minimum
Microphone
Set the microphone on a level surface at ear height at least six feet from the TV.
Use a seat backrest or tripod so as to pick up sound from all directions.
Maximum height above speakers
Height of TV speakers
3 ft.
Be sure the height of the microphone is within three feet of the speaker height.
Microphone
Center the microphone in front of the TV.
For assistance call 1(800) 332-2119
24
4
TV Menus
Press MENU on the remote control to open the main menu and access these settings.
Picture
Picture Video
Settings in this menu are saved for the current input only.
To make picture adjustments:
From the Picture > Video menu
1.
2.
Press
Press
to highlight an option
to adjust.
While watching TV
1.
2.
3.
Press the
Press
Press
VIDEO key.
to select a video option.
to change the setting.
Picture
Mode
Brilliant
Game
Bright
Natural
For use under bright light.
Optimizes picture and video processing for game consoles
For most daytime viewing
For most nighttime viewing
Use Picture Modes to get the best image under different viewing conditions.
Set the Picture Mode first, before changing other video settings.
Advanced Modes. 164 and 265 Series. Contact your professional installer for setup.
In most home lighting situations, medium contrast looks best. Stored for each Picture Mode.
Adjusts overall picture brightness. Settings are stored independently for each Picture Mode.
Contrast
Brightness
Color
Tint
Adjusts overall color intensity from monochromatic to fully saturated. Saved by input.
Adjusts the red-to-green ratio. Saved by input.
Sharpness
Adjusts picture detail and clarity. Saved by input.
Color Temp
High gives white a cool cast. Low gives white a warm cast. Stored for each Picture Mode.
Video Noise
Reduces minor noise (graininess) in the picture. Saved by input.
EdgeEnhance
164 and 265 Series TVs. EdgeEnhance™ makes the image appear sharper. Saved by input.
DeepField
Imager
Backlight
164 and 265 Series TVs. Provides strong contrast with detail over mixed screen content. Demo displays a split picture to show On (right side) and Off (left side). Saved by input.
Adjusts peak brightness of the backlight. Applies uniformly to all inputs. Press ENTER to turn the backlight on or off.
Picture Picture+
(Picture Plus)
Video Mute
Screensaver
Film Mode
True 120 Hz (154,
164 series)
True 240 Hz (265 series)
Test Picture
Displays a solid background when there is no video signal from the current input.
Displays a screensaver while playing an audio-only source.
480i and 1080i signals only. In Auto, the TV automatically detects and applies film-decoding correction to movies filmed at 24 frames per second. Try the Off setting if images show many jagged edges. Setting saved by input.
Reduces motion blur in action scenes. Works in conjunction with Film Mode. Press adjustment screen.
Displays a test picture.
ENTER to see an
For assistance call 1(800) 332-2119
4. TV Menus
25
Picture, continued
Picture Reset
•
•
Resets sound and picture adjustments for the current input. Highlight the Reset icon and press ENTER twice to perform reset.
Reset
has no effect on universal settings ( Balance, Listen To, Language) or on
Advanced picture settings.
Picture Perfect
(PerfectColor™/PerfecTint™)
265 Series. Sliders let you adjust the saturation (intensity) and hues of six separate colors for the current image source.
Picture Advanced
Advanced Modes. Contact your professional installer for setup.
164 Series. Special/ADV.
265 Series. ISF Day/ADV1, ISF Night/ADV2
Sound
Sound Audio
Settings in this menu are saved for the current input only. To make audio adjustments:
From the Sound > Audio menu While watching TV
1.
2.
Press
Press
to highlight an option
to adjust.
1.
2.
3.
Press the AUDIO key.
Press to select an audio option.
Press to change the setting.
TV Speakers
Bass
On
Off
Center
Turns on the internal TV speakers.
Turns off the internal TV speakers so you hear sound only through a connected device
(A/V receiver or headphones).
Makes the TV’s speaker array act as a center channel.
Sound > Global > Center
Channel must be set to On to use this option. See the detailed owner’s guide at www.mitsubishi-tv.com for use of this feature.
Controls bass sound from the TV speakers.
Treble
Controls high-pitched sound from the TV speakers.
Balance
Controls audio balance between the right and left TV speakers (Sound Mode Stereo only)
Subwoofer [Subwoofer level adjustment]
Sound Mode Stereo
Adjusts the volume level of a connected subwoofer. Set
woofer to On to make this adjustment available.
No special audio effects from the TV speakers
Sound > Global > Sub-
Surround
Level Sound
Music
Night
On, Off
Modifies audio from the TV speakers.
• For monaural (non-stereo) programs, creates a simulated stereo effect.
• For stereo programs, creates a simulated surround sound effect.
• The TV’s speaker array plays surround sound if available.
Optimizes the TV’s speaker array for music listening.
Focuses the TV’s speaker array to a single point to limit sound heard by others outside the room. Press ENTER to adjust the focal point (Night Angle).
Reduces differences in sound volume between programming segments.
For assistance call 1(800) 332-2119
26
4. TV Menus
Sound, continued
Analog Listen To
(For ANT analog channels)
Stereo
Mono
SAP
The TV plays stereo broadcasts in stereo and mono broadcasts in mono.
Reduces background noise. Use when receiving a weak stereo audio signal.
Second Audio Program. Selects an additional monaural sound track.
Sound Global
Settings in this menu apply to all inputs.
Analog Audio
Out
These settings affect audio from the
AVR/SURROUND jacks.
Fixed
Use with an analog A/V receiver.
Variable
Rear
Use with headphones; adjust headphone volume using the TV’s remote control.
Use when supplementing the TV’s speaker array with external rear speakers.
Select
On to turn on audio to a connected subwoofer. Set to Off if no subwoofer is connected.
Subwoofer
Center Channel
On allows the TV’s speakers to complement your external sound system as a center channel. Set to Off if not in use.
Sound Auto SP
265 Series. See page 23 for setup instructions.
Sound SoundPro
Lets you set up the Sound Projector speaker array manually. See page 22.
Captions
Captions Services
Service
Digital
Analog
On if Mute: Displays digital closed-caption signal Caption 1 (digital) or CC1 (analog) when audio from the
TV speakers is muted. While watching TV, press MUTE to turn closed captions on/off.
Caption 1–Caption 6: Caption signals sent by the broadcaster.
•
•
CC 1–CC 4.
Standard closed-caption signals
Text 1–Text 4.
Text-service signals
Captions Font
As Broadcast changes settings to those selected by the captions provider, or, if none, to the
TV’s own caption defaults.
Captions Color
A white font on a black translucent background makes an easy-to-read combination.
For assistance call 1(800) 332-2119
4. TV Menus
Setup
Setup Language
•
•
Select either English or Spanish for on-screen menus.
Select the language for a digital program from the
ANT input (if available).
27
Setup Clock
Set the TV clock to:
•
•
Use the TV Timer to power on the TV automatically at a preset time
Receive correct updates to ChannelView listings
Note: When the Daylight Saving Time change occurs, you must open this menu and set the TV’s clock ahead or back.
Setup Timer
The Timer tells the TV to power on automatically at a time you set. Use this menu to set a day, time, input, and channel for the Timer. If the TV is already on at the set time, the TV will automatically change to the designated channel or input.
• The TV clock must be set before you can use the Timer feature.
• As a reminder that the TV Timer is set, the TV POWER indicator flashes slowly while the TV is powered off.
• When the Timer turns on the TV, press any key on the remote control to keep it from turning off after five minutes.
Setup Channel
See “Memorizing Channels with Channel Scan” on page 9 to scan for all available channels on the ANT input.
Edit
After channel scan,
Edit lets you add and delete memorized channels.
• Press
PAGE DN/UP to jump to the next or previous page of channel numbers.
• Press to move through all channel numbers, one at a time.
Adding/Deleting Channels Using the Channel Edit Menu
• Channels marked with a check are in memory.
•
•
To add or delete a channel from memory, highlight the channel number and press ENTER.
To add a single digital channel not in the list, see the full owner’s guide at www.mitsubishi-tv.com.
Setup Energy
Blue Glow
(265 series)
On, Off
Select On to see blue accent lighting when the TV is powered on.
Setup Network
Ethernet Connection
Wireless Connection
See “Home Network Setup” on page 18.
For assistance call 1(800) 332-2119
28
4. TV Menus
Inputs
Inputs Name
•
•
•
•
Lets you assign or
Lets you turn the change names of inputs appearing in the
Input Selection menu.
Ant and Bluetooth inputs On/Off (to display or hide them in the Input
Selection menu); a paired device is cleared from memory when the Bluetooth icon is turned off.
Lets you delete unused HDMI inputs from the
Input Selection menu.
Highlight the input and press
ENTER to see the name choices.
Inputs Learn
265 Series. Sets up or changes NetCommand IR control of the current device.
See the full owner’s guide at www.mitsubishi-tv.com.
Inputs AVR
265 Series. Sets up or changes NetCommand IR control of an A/V receiver.
See the full owner’s guide at www.mitsubishi-tv.com.
Inputs
HDMI
Control
On, Off
Select On or Off to enable or disable the TV’s control of a CEC-enabled HDMI device. See the full owner’s guide at www.mitsubishi-tv.com for use of this feature.
Inputs Order
Lets you rearrange icons in the Input Selection menu.
Inputs Demo
See demonstrations showcasing selected TV features.
For assistance call 1(800) 332-2119
4. TV Menus
29
Lock
Parental Menu
The TV comes from the factory with the rating locks turned off and with pre-set U.S. ratings TV-PG and movie rating PG. You must turn on blocking for U.S. ratings to activate these rating restrictions. You will be prompted to enter a pass code when you select Lock on the main menu.
Important Notes on Rating Locks
• Parental menu rating locks apply only to channels and signals received on the ANT and composite VIDEO jacks.
• Other menu rating locks apply only to digital channels received on ANT.
• When viewing a cable box, satellite receiver, or other device connected to the component Y Pb Pr or HDMI inputs, check the device’s owner’s guide for parental locks.
• When accessing VUDU’s internet movie service, use the parental controls provided by VUDU.
Lock Parental
Lock
TV
Rating
Movie
Rating
Start Time/
Stop Time
Disables or enables blocking based on V-Chip signals and the U.S. rating system.
Highlight the rating level you wish to change and press ENTER to block it ( ) or allow it ( ).
You can apply supplemental content blocking to the age-based ratings by using the TV content categories. (
FV, D, L, S, V)
Highlight the rating level you wish to change and press ENTER to block it ( ) or allow it
( ).
Sets the time of day for enforcement of rating restrictions set in the Parental menu.
Note: To make rating restrictions active 24 hours a day, make Start Time and Stop Time the same.
Lock Time
Blocks all use of the TV during the time period you specify. Once a lock time is set, it goes into effect immediately and you must enter a pass code to use the TV during the lock period. To reactivate the time lock, power the TV off and then back on. To make
Lock by
Time active 24 hours a day, make Start Time and Stop Time the same.
Lock Channel
The Channel Lock menu lists channels currently in memory (see page 27). Highlight a channel and press
ENTER to lock ( ) or allow (
) the channel. Channels locks will be cleared the next time you perform a channel scan.
Lock Panel
Use this option if small children try to press TV buttons.
•
•
To release the Panel Lock from the TV’s control panel, press and hold the
INPUT button for ten seconds. If the TV is powered off, press
POWER after the lock releases to power on the
TV.
To reactivate the lock, return to this menu and change the setting to
On.
Lock Other
Other Menu Options (alternate rating system)
This TV can recognize new rating systems that may come into effect in the future. Such alternate rating systems will apply only to digital programming received on the ANT input.
For assistance call 1(800) 332-2119
30
Appendices
Appendix A: Programming the Remote Control
Programming the Remote Control
1.
Change the control mode to match the device type.
TV
CAB/SAT DVD
AUDIO
VCR
TV
CAB/SAT DVD
AUDIO
VCR
Mode Affected Device
CAB/SAT
Cable Box, DTV Receiver, Satellite Receiver
VCR
VCR, DVR, DVD Player/Recorder
DVD
AUDIO
DVD Player/Recorder, DVR, VCR
A/V Receiver, Audio Amplifier, CD Player
2.
Press and hold
POWER on the remote control for several seconds until the key blinks twice and goes off.
3.
4.
5.
Enter the first five-digit code listed for your equipment.
Point the remote control at the equipment and press
POWER. If the product has no power on/off function, press a different key, such as
(PLAY), (STOP),
VOLUME UP, or MUTE.
If the equipment does not respond, repeat the preceding two steps using the next five-digit code.
Once you have found the correct code, write it in the space below for future reference.
Mode
CABLE/SAT
VCR
DVD
AUDIO
Device Type Code
This is an abbreviated list showing the most popular codes. For a full list, see the detailed owner’s guide at www.mitsubishi-tv.com.
Cable Boxes
General Instrument
Jerrold
Motorola
Pace
Pioneer
10476
11376, 11187, 10476
11982, 11877, 11376
11877, 10877
Scientific Atlanta 11877, 10877
A/V Receivers
Bose
Denon
41933, 41841, 41629, 41253,
41229, 40639
42857, 42279
Harman/Kardon 42443, 42241, 41306, 41304,
40891
Integra 41805, 41320, 41298
JVC
Kenwood
Mitsubishi
42331, 42239, 42040,
41495, 41374
41570, 41569, 41313
Onkyo
Panasonic
Pioneer
Sony
41957, 41922, 41921, 41920,
41393
41805, 41531, 41320, 41298,
40842
41763, 41633, 41548, 41518,
41316, 41308, 41288, 41275,
42967, 42452, 42221, 41764
41935, 41384, 41023, 40630
Technics
Yamaha
41759, 41758, 41658, 41622,
41558, 41441, 41258, 41058,
42522, 42216, 42172, 41858,
41822
41518, 41308
41476, 41376, 41375, 41331,
41276, 41176, 40376, 40176
42471, 42467, 42061, 41815
Satellite Receivers
DirecTV 11749, 11377, 11142, 10749,
10639, 10566, 10392, 10247
11856, 11609, 11442, 11414,
11109, 11076
11775, 1150, 1077 Dish Network
System
Hughes Network
Systems
Mitsubishi
11749, 11442, 11142, 10749
10749
RCA
Samsung
10566, 10392, 10143
11609, 11442, 11377, 11276,
11109
VCRs
Hitachi
JVC
Magnavox
Matsushita
MGA
Mitsubishi
Panasonic
RCA
Sony
Tivo
Toshiba
Zenith
20042, 20000
20067
21593, 20593, 20081, 20039,
20035, 20000
20162, 20035
20043
20173, 20067, 20043
21062, 20616, 20614, 20162,
20035
20880, 20060, 20042
21972, 21032, 20636, 20035,
20033, 20032, 20000
20739, 20636, 20618
21972, 21008, 20045, 20043
21139, 20039, 20037, 20033,
20000
DVD Players
Apex Digital
Coby
Denon
31061, 31056, 31020, 31004,
30797, 30796, 30794, 30755,
30672
31628, 31351, 31177, 31165,
31107, 31086, 30852, 30778
32258, 30634, 30490
For assistance call 1(800) 332-2119
DVD Players
Funai
Hitachi
Insignia
Integra
JVC
LG
Magnavox
Mitsubishi
Onkyo
Panasonic
Philips
Pioneer
RCA
Samsung
Sharp
Sony
Sylvania
Tivo
Yamaha
Zenith
30675
30664, 30573
32596, 32428, 32095, 30675
32147, 31769, 30627, 30571
32365, 31602, 31550, 31275,
31164, 30867, 30623, 30558
31602, 30869, 30741, 30591
31506, 31472, 31354, 31177,
30675, 30646, 30539, 30503
31521, 30521
32147, 31769, 30627, 30503
31762, 31641, 31579, 30703,
30632, 30503, 30490
32084, 32056, 31340,,
31267, 30675, 30646, 30539,
30503, 32434, 31506, 31354
31571, 31512, 31460, 30632,
30631, 30571, 30525, 30142
32442
32213, 31769, 30822, 30790,
30571, 30522
32069, 31470, 31075, 31044,
30820, 30573, 30490, 30199
32556, 32489, 32369, 32329
32250, 31256, 30752, 30675,
30630
31633, 31536, 31516, 31431,
31070, 31033, 30864, 30533
30675
31512, 31503
32558, 32298, 30817, 30646,
30545, 30539, 30490
30869, 30741, 30591, 30503
Appendices
31
Appendix B: Troubleshooting
To contact Mitsubishi customer service, see page 6.
TV Reset Comparison Guide
You can resolve many common TV problems using the reset functions described in the following table.
IMPORTANT
Before you change sound or picture settings: If picture or sound settings seem wrong for a broadcast channel (a channel from the ANT input, a cable box, or satellite receiver), first check other channels from the same input before changing settings. If most other channels from the same input seem correct, there is likely a problem with the broadcast rather than with the
TV. Use care in this case, as changes you make to fix problems on individual channels also affect all other channels on the same input.
Reset Name
Format
When to Use
If the picture shape seems incorrect, use the FORMAT key to change the picture shape.
How to Use
Press FORMAT to cycle through the picture shapes available for the signal.
PerfectColor™/
PerfecTint™
Reset (265
Series)
(for the single input currently being watched)
When the color intensities seem out of balance, use the
PerfectColor/PerfecTint reset to reset the color balances to the original factory settings.
Both PerfectColor and
PerfecTint are reset at the same time.
1.
2.
3.
While viewing the input to reset, press
MENU and go to Picture >
Perfect.
Press ENTER to display the
PerfectColor adjustment screen.
Press
CANCEL to reset the colors.
Resulting Action
The last-used format for the signal type will be recalled on the input.
Note: Also check the aspect ratio feature on your cable box or satellite receiver as this may be altering the picture.
All PerfectColor/PerfecTint sliders are reset to the original center position. The PefectColor/
PerfecTint settings for other inputs remain unchanged.
A/V Memory
Reset
(for the single current input)
A/V Reset
(for all inputs)
Channel
Memorization
Lock Menu
Pass Code
When audio and/ or video settings for a single input seem incorrect, use A/V
Memory Reset to return the input to the original factory settings.
1.
2.
3.
While viewing the input to reset, press MENU and go to Picture >
Reset.
Press
Press
to highlight
Reset.
ENTER again to reset.
To reset audio and video adjustments for all inputs to the original factory settings.
While viewing the TV, press the control-panel buttons
INPUT and
VOLUME DOWN at the same time for at least two seconds.
All Audio and Video settings for the individual input are reset except for the global settings for audio Balance, Listen To,
Language, Video Mute, True 120
Hz.
All Audio and Video settings are returned to the original factory settings, including global settings not affected by
Picture > Reset.
To erase and re-memorize channels on the
ANT
input.
To change your menu pass code
Lock
1.
2.
3.
4.
5.
Press MENU and go to Setup >
Channel.
Highlight the reception mode, e.g. Ant Air, and press ENTER.
Highlight All Channels and press ENTER.
Highlight Scan.
Press ENTER to start channel memorization.
All previously memorized channels for the antenna input are erased and a new set of memorized channels is created. To add or delete individual channels, see the Setup > Channel > Edit menu instructions on page 27.
See the detailed owner’s guide at www.mitsubishi-tv.com for instructions.
For assistance call 1(800) 332-2119
32
Appendices
Appendix B: Troubleshooting, continued
Reset Name
Control-Panel
Lock Release
When to Use
To re-enable the control-panel buttons after activation of the
Control-Panel Lock
System Reset
If the TV does not turn on or off, does not respond to the remote control or controlpanel buttons, or has audio but no video.
How to Use
Press and hold the INPUT button on the control panel for ten seconds. If the TV is powered off, you can now press the POWER button to turn it on.
Press and hold the POWER button on the control panel for ten seconds.
Resulting Action
Allows the control panel to be unlocked if the remote control is misplaced.
The TV will turn off. Power on the
TV and the green LED will flash quickly for about one minute. The changes you made most recently, before using SYSTEM RESET, may be lost.
TV Reset
IMPORTANT:
Use this reset only if other troubleshooting has been unsuccessful.
VUDU
Reset VUDU
Account Password
VUDU
Reset Parental
Controls Pass code
To reset all consumeraccessible settings and all memories to the original factory defaults.
Use TV Reset if the TV can respond to controls but TV behavior is abnormal.
CAUTION: All ownerperformed setups and adjustments will be erased.
You have forgotten your account password.
1.
2.
3.
While viewing the TV, press
MENU to display the TV main menu.
With the main menu displayed, press number keys 1 2 3 to display the Reset menu.
READ THE ON-SCREEN
WARNING AND INSTRUC-
TIONS.
• If you do not wish to use this reset, press EXIT or MENU to back out.
• If you wish to continue, press ENTER to erase all memories and settings.
Using a computer, go to www.VUDU.com.
The TV will start the initialization process and then turn off.
Power on the TV and the front green LED will start flashing. All memory and settings outlined in this Owner’s Guide will need to be set again.
Reset your account password from the VUDU website (requires access to e-mail).
You have forgotten your pass code.
Call VUDU Customer Care at
1-888-554-VUDU (8838).
VUDU Customer Care will reset your pass code.
Common Picture Problems
Symptom
1.
Picture does not look like a high-definition picture.
2.
TV has sound but no picture.
Remarks
Compare the picture to the TV’s test picture (Picture > Picture+ menu) to check if the source signal is supplying a lesser-quality image.
Not all signals are high-definition signals. To receive high-definition programming from your cable or satellite provider, you must subscribe to the provider’s high-definition service. Some over-the-air broadcasts are in high-definition and can be received with a highquality antenna suited to your location.
•
•
•
Press MENU on the remote control. If the menu displays, then there is a problem with the incoming signal.
Check that all video inputs are plugged in firmly to the correct input jacks.
Press and hold the POWER button on the control panel for ten seconds to perform System Reset.
For assistance call 1(800) 332-2119
Appendices
33
Appendix B: Troubleshooting, continued
Common Picture Problems
Symptom
3.
A color program appears as a black and white image, or the colors are dim, or the screen is black.
4.
Picture from an HDMI input is noisy
(poor quality).
Remarks
•
•
•
If using component video, check that the red, green, and blue input cables are correctly connected to the red, green, and blue component video jacks.
If using composite video, check that the incoming cable is connected the TV’s green Y/VIDEO jack.
The PerfectColor color balance has been incorrectly set. Reset the PerfectColor balance.
• C ompare the picture to the TV’s test picture (Picture > Picture+
• menu) to check the source of the noise.
Upgrade a Category 1 (unmarked) HDMI cable to a Category 2 high-speed HDMI cable.
Home Network
Symptom Remarks
1.
I cannot connect the TV to the network. Go the Setup > Network menu. Obtain the TV MAC address and provide it to the router.
2.
I plugged in a wireless USB adapter, but the wireless connection is not working.
The network may be locked. Go to setup > Network. Highlight the network name and supply the pass code.
3.
The INTERNET key only goes to VUDU. Normal operation. The TV receives all internet services through
VUDU. The TV does not provide full internet access as does a web browser on a computer.
Trademark and License Information
LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY
EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS,
INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE.
Manufactured under license from Cambridge Mechatronics Ltd.
Rapidfire and the 1... logo are trademarks of Cambridge Mechatronics Ltd
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Mitsubishi Electric is under license. Other trademarks and trade names are those of their respective owners.
Digital Light Processing ® and DLP ® are registered trademarks of Texas Instruments.
Manufactured under license from Dolby Laboratories. Dolby is a trademark of Dolby Laboratories.
ENERGY STAR ® and the ENERGY STAR mark are registered U.S. marks. ENERGY STAR is a registered mark owned by the U.S. government.
HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Imaging Science Foundation Certified Calibration Controls
The software in this TV is based in part on the work of the Independent JPEG Group, copyright © 1991-1998, Thomas
G. Lane, all rights reserved.
VUDU
™
is a trademark of VUDU, Inc.
“x.v.Color” and the “x.v.Color” logo are trademarks of Sony Corporation.
ChannelView™, DeepField™ Imager, Easy Connect™, EdgeEnhance™, NetCommand®, PerfectColor™, PerfecTint™,
Plush 1080p® 5G, StreamTV™, Unisen™ are trademarks of Mitsubishi Digital Electronics America, Inc.
For assistance call 1(800) 332-2119
34
Trademark and License Information
Mitsubishi TV Software
END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE
IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and
Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”). By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
The Software is protected by United States copyright laws and international treaty provisions, as well as other intellectual property laws and treaties. The Software is licensed, not sold.
1. LICENSE GRANT. MDEA grants you a non-exclusive, non-transferable, limited right and license to use one copy of the Software only with the Mitsubishi television model that included this owner’s guide and owned by you.
2.
RIGHTS AND LIMITATIONS.
Software Not for Resale. You may not resell or otherwise transfer for value the Software, except in conjunction with a sale of the TV that
Software has been pre installed.
Prohibition on Reverse Engineering, Decompilation and Disassembly. The Software contains trade secrets or other proprietary material in its human perceivable form and to protect them, you may not reverse engineer, decompile, or disassemble, or otherwise reduce the
Software to any human perceivable form, except to the extent that the foregoing restriction is expressly prohibited by applicable law.
Separation of Components. The Software is licensed as a single product. Its component parts may not be separated for use on more than one TV.
No Rental. You may not rent, lease, lend, or sublicense the Software.
Trademarks. This License Agreement does not grant you any rights to any trademarks of MDEA.
3. VIOLATIONS. You understand that any use, copying or transfer of the Software, except as permitted pursuant to this License, may subject you to serious criminal and civil penalties including damages and an award to MDEA of attorneys’ fees in connection with any violation of this License. You further understand that you may be held legally responsible for any copyright infringement or other violation of intellectual property rights that is caused, encouraged, or induced by your failure to abide by the terms of the License. This license is effective until terminated, and will terminate immediately without notice from MDEA or judicial resolution if you fail to comply with any provision of this License.
4.
COPYRIGHT. All title and intellectual property rights in and to the Software (including but not limited to any images, photographs, animations, video, audio, music, text, and “applets” incorporated into the Software), and any accompanying printed materials are owned by or licensed to MDEA. All title and intellectual property rights in and to the content which may be accessed through use of the Software is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. This License Agreement grants you no rights to use such content, except that you own the media on which the Software is recorded, but MDEA and its licensors retain ownership of the Software itself. All rights not expressly granted are reserved by MDEA.
5.
EXPORT RESTRICTIONS. MDEA is licensing the Software for use within the United States. You agree that you will not export or re-export the Software. You specifically agree not to export or re-export the Software: (i) to any country to which the U.S. has embargoed or restricted the export of goods or services, which currently include, but are not necessarily limited to Cuba, Iran, Iraq, Libya,
North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the Software back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software in the design, development, or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from participating in
U.S. export transactions by any federal agency of the U.S. government. You warrant and represent that neither the BXA nor any other U.S. federal agency has suspended, revoked, or denied your export privileges.
6.
DISCLAIMER OF WARRANTY. EXCEPT AS OTHERWISE PROVIDED IN THIS LICENSE OR IN THE LIMITED WARRANTY
APPLICABLE TO THE TV, MDEA MAKES NO OTHER WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE SOFTWARE
AND HEREBY EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH
RESPECT TO THE SOFTWARE. ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED BY MDEA. IN
NO EVENT SHALL MDEA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT, IN TORT OR OTHERWISE, FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE. BECAUSE SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE ABOVE LIMITATION MAY
NOT APPLY TO YOU.
7.
LIMITATION OF LIABILITY. MDEA SHALL NOT, UNDER ANY CIRCUMSTANCES BE LIABLE TO YOU OR ANY THIRD
PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR
OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR EXPENDITURES
MADE OR COMMITTED FOR IN RELIANCE ON THE CONTINUATION OF THIS LICENSE. YOU AGREE THAT NEITHER MDEA’S
BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL CONSTITUTE A FAILURE OF THE
ESSENTIAL PURPOSE OF THIS LICENSE. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. MDEA’s liability to you for direct damages for any cause whatsoever and regardless of the form of the action, will be limited to the money paid by you for the TV (based on fair market value of the TV) that caused the damages.
8. GENERAL. This License Agreement will be governed by the laws of the State of California.
For assistance call 1(800) 332-2119
Trademark and License Information
35
GNU General Public License
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
675 Mass Ave, Cambridge, MA 02139, USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this
License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.
If you are interested in obtaining open source code for this product, please contact Mitsubishi at
(800) 332-2119. A nominal handling and mailing charge may apply.
For assistance call 1(800) 332-2119
36
Trademark and License Information
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the
Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM
IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE
PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY
TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE
PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007
Copyright © 2007 Free Software Foundation, Inc. <http://fsf.org/>
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
The GNU General Public License is a free, copyleft license for software and other kinds of works.
The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change all versions of a program--to make sure it remains free software for all its users. We, the Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work released this way by its authors. You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things.
To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright on the software, and (2) offer you this License giving you legal permission to copy, distribute and/or modify it.
For the developers’ and authors’ protection, the GPL clearly explains that there is no warranty for this free software. For both users’ and authors’ sake, the GPL requires that modified versions be marked as changed, so that their problems will not be attributed erroneously to authors of previous versions.
Some devices are designed to deny users access to install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting users’ freedom to change the software. The systematic pattern of such abuse occurs in the area of products for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this version of the GPL to prohibit the practice for those products. If such problems arise substantially in other domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed to protect the freedom of users.
Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software on general-purpose computers, but in those that do, we wish to avoid the special danger that patents applied to a free program could make it effectively proprietary. To prevent this, the GPL assures that patents cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks.
“The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may be individuals or organizations.
To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an exact copy. The resulting work is called a “modified version” of the earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work based on the Program.
To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable copyright law, except executing it on a computer or modifying a private copy. Propagation includes copying, distribution (with or without modification), making available to the public, and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a computer network, with no transfer of a copy, is not conveying.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License. If the interface presents a list of user commands or options, such as a menu, a prominent item in the list meets this criterion.
The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any non-source form of a work.
A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular programming language, one that is widely used among developers working in that language.
The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major Component, but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which an implementation is available to the public in source code form. A “Major Component”, in this context, means a major essential component (kernel, window system, and so on) of the specific operating system (if any) on which the executable work runs, or a compiler used to produce the work, or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object code and to modify the work, including scripts to control those activities. However, it does not include the work’s System Libraries, or general-purpose tools or generally available free programs which are used unmodified in performing those activities but which are not part of the work. For example, Corresponding Source includes interface definition files associated with source files for the work, and the source code for shared libraries and dynamically linked subprograms that the work is specifically designed to require, such as by intimate data communication or control flow between those subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same work.
All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law.
You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force. You may convey covered works to others for the sole purpose of having them make modifications exclusively for you, or provide you with facilities for running those works, provided that you comply with the terms of this License in conveying all material for which you do not control copyright. Those thus making or running the covered works for you must do so exclusively on your behalf, under your direction and control, on terms that prohibit them from making any copies of your copyrighted material outside their relationship with you.
Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10 makes it unnecessary.
No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modification of the work as a means of enforcing, against the work’s users, your or third parties’ legal rights to forbid circumvention of technological measures.
You may convey verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice; keep intact all notices stating that this License and any non-permissive terms added in accord with section 7 apply to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along with the
Program.
You may charge any price or no price for each copy that you convey, and you may offer support or warranty protection for a fee.
You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, provided that you also meet all of these conditions: a) The work must carry prominent notices stating that you modified it, and giving a relevant date.
b) The work must carry prominent notices stating that it is released under this License and any conditions added under section 7. This requirement modifies the requirement in section 4 to “keep intact all notices”.
c) You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along with any applicable section 7 additional terms, to the whole of the work, and all its parts, regardless of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such permission if you have separately received it.
d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so.
A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation’s users beyond what the individual works permit. Inclusion of a covered work in an aggregate does not cause this License to apply to the other parts of the aggregate.
6. Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine-readable Corresponding Source under the terms of this License, in one of these ways: a) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the Corresponding Source fixed on a durable physical medium customarily used for software interchange.
b) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a written offer, valid for at least three years and valid for as long as you offer spare parts or customer support for that product model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source from a network server at no charge.
c) Convey individual copies of the object code with a copy of the written offer to provide the Corresponding Source. This alternative is allowed only occasionally and noncommercially, and only if you received the object code with such an offer, in accord with subsection 6b.
d) Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source in the same way through the same place at no further charge. You need not require recipients to copy the Corresponding Source along with the object code. If the place to copy the object code is a network server, the Corresponding Source may be on a different server (operated by you or a third party) that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source. Regardless of what server hosts the Corresponding Source, you
For assistance call 1(800) 332-2119
Trademark and License Information
37
remain obligated to ensure that it is available for as long as needed to satisfy these requirements.
e) Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and Corresponding Source of the work are being offered to the general public at no charge under subsection
6d.
A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be included in conveying the object code work.
A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or sold for incorporation into a dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of coverage. For a particular product received by a particular user, “normally used” refers to a typical or common use of that class of product, regardless of the status of the particular user or of the way in which the particular user actually uses, or expects or is expected to use, the product. A product is a consumer product regardless of whether the product has substantial commercial, industrial or non-consumer uses, unless such uses represent the only significant mode of use of the product.
“Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and execute modified versions of a covered work in that User Product from a modified version of its Corresponding Source. The information must suffice to ensure that the continued functioning of the modified object code is in no case prevented or interfered with solely because modification has been made.
If you convey an object code work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a transaction in which the right of possession and use of the User Product is transferred to the recipient in perpetuity or for a fixed term (regardless of how the transaction is characterized), the Corresponding Source conveyed under this section must be accompanied by the Installation Information. But this requirement does not apply if neither you nor any third party retains the ability to install modified object code on the User Product (for example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a requirement to continue to provide support service, warranty, or updates for a work that has been modified or installed by the recipient, or for the User
Product in which it has been modified or installed. Access to a network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network.
Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented (and with an implementation available to the public in source code form), and must require no special password or key for unpacking, reading or copying.
“Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire
Program remains governed by this License without regard to the additional permissions.
When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it. (Additional permissions may be written to require their own removal in certain cases when you modify the work.) You may place additional permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material) supplement the terms of this License with terms: a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or b) Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal Notices displayed by works containing it; or c) Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different from the original version; or d) Limiting the use for publicity purposes of names of licensors or authors of the material; or e) Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or f) Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual assumptions of liability to the recipient, for any liability that these contractual assumptions directly impose on those licensors and authors.
All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term. If a license document contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work material governed by the terms of that license document, provided that the further restriction does not survive such relicensing or conveying.
If you add terms to a covered work in accord with this section, you must place, in the relevant source files, a statement of the additional terms that apply to those files, or a notice indicating where to find the applicable terms.
Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as exceptions; the above requirements apply either way.
8. Termination.
You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11).
However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until the copyright holder explicitly and finally terminates your license, and (b) permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior to 60 days after the cessation.
Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you of the violation by some reasonable means, this is the first time you have received notice of violation of this
License (for any work) from that copyright holder, and you cure the violation prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the licenses of parties who have received copies or rights from you under this License. If your rights have been terminated and not permanently reinstated, you do not qualify to receive new licenses for the same material under section 10.
9. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by modifying or propagating a covered work, you indicate your acceptance of this License to do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that work, subject to this License. You are not responsible for enforcing compliance by third parties with this License.
An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations. If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party’s predecessor in interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the predecessor in interest, if the predecessor has it or can get it with reasonable efforts.
You may not impose any further restrictions on the exercise of the rights granted or affirmed under this License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights granted under this
License, and you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed is called the contributor’s “contributor version”.
A contributor’s “essential patent claims” are all patent claims owned or controlled by the contributor, whether already acquired or hereafter acquired, that would be infringed by some manner, permitted by this License, of making, using, or selling its contributor version, but do not include claims that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, “control” includes the right to grant patent sublicenses in a manner consistent with the requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor’s essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and propagate the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of the work is not available for anyone to copy, free of charge and under the terms of this License, through a publicly available network server or other readily accessible means, then you must either (1) cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the patent license for this particular work, or (3) arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream recipients. “Knowingly relying” means you have actual knowledge that, but for the patent license, your conveying the covered work in a country, or your recipient’s use of the covered work in a country, would infringe one or more identifiable patents in that country that you have reason to believe are valid.
If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work, and grant a patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.
A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-exercise of one or more of the rights that are specifically granted under this
License. You may not convey a covered work if you are a party to an arrangement with a third party that is in the business of distributing software, under which you make payment to the third party based on the extent of your activity of conveying the work, and under which the third party grants, to any of the parties who would receive the covered work from you, a discriminatory patent license (a) in connection with copies of the covered work conveyed by you (or copies made from those copies), or (b) primarily for and in connection with specific products or compilations that contain the covered work, unless you entered into that arrangement, or that patent license was granted, prior to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be available to you under applicable patent law.
12. No Surrender of Others’ Freedom.
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a covered work so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty for further conveying from those to whom you convey the Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the Program.
Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version 3 of the GNU Affero General Public License into a single combined work, and to convey the resulting work. The terms of this License will continue to apply to the part which is the covered work, but the special requirements of the GNU Affero General Public License, section 13, concerning interaction through a network will apply to the combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU General Public License “or any later version” applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose any version ever published by the Free Software Foundation.
If the Program specifies that a proxy can decide which future versions of the GNU General Public License can be used, that proxy’s public statement of acceptance of a version permanently authorizes you to choose that version for the Program.
Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT
LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts shall apply local law that most closely approximates an absolute waiver of all civil liability in connection with the Program, unless a warranty or assumption of liability accompanies a copy of the Program in return for a fee.
For assistance call 1(800) 332-2119
38
Warranty
Mitsubishi LCD Flat Panel HDTV Limited Warranty
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants to the original purchaser of this LCD Flat Panel HDTV that if purchased from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of improper workmanship and/or material:
a. Parts. All parts (except any software incorporated into this HDTV) are warranted for a period of one year from the date of the original purchase at retail. We will repair or replace, at our option, any defective part without charge for the part. Parts used for replacement may be replaced with those of like kind and quality and may be new or remanufactured. Parts used for replacement are warranted for the remainder of the original warranty period.
b. Embedded Software. MDEA warrants that all software incorporated into this HDTV (the “Embedded Software”) will perform in accordance with the functional description of Embedded Software in all material respects, but MDEA does not warrant that the Embedded Software is error-free. The warranty contained in this section shall continue for a period of one year, from the date of the original purchase from the authorized dealer. If, after prompt notice within the warranty period, MDEA determines that the Embedded Software has failed to perform in accordance with such functional description in all material respects and if such failure is not due to accident, misuse, modification or misapplication of the Embedded Software, then
MDEA shall modify or replace the nonconforming Embedded Software at no charge to you, which at MDEA’s sole discretion may be fulfilled by means of modification or replacement software contained on a replacement memory card for Consumer installation. The foregoing shall be MDEA’s sole obligation to you under this limited warranty. All rights under this limited warranty on the Embedded Software also subject to your compliance with the terms of the Software License Agreement applicable to this HDTV, and this limited warranty on the Embedded Software shall be null and void if the Embedded Software is modified or changed in any manner except as specifically authorized by MDEA.
c. Labor. For certain items that are designed to be replaced by the consumer, including (but not limited to) some Embedded Software, the consumer is solely responsible for any replacement labor. For all other parts, we will provide the labor for a warranty repair by an authorized MITSUBISHI service center without charge for one year from the original date of purchase at retail.
d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within the applicable warranty time period.
BEFORE REQUESTING SERVICE, please review the TV owner’s guide to insure proper installation and correct customer control adjustment. If the problem persists, please arrange for warranty service.
1. TO OBTAIN WARRANTY SERVICE:
a. Contact your nearest authorized MITSUBISHI service center whose name and address can be obtained from your MIT-
SUBISHI dealer, by writing to the address provided below, calling MDEA at 800-332-2119, or using the support feature of our website at www.Mitsubishi-tv.com.
b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your television is located within the geographic territory customarily covered by an authorized MITSUBISHI service center. If not, you must either deliver your television to an authorized service location at your own expense, or pay for any travel and/or transportation costs the service center may charge to and from you home. Actual service labor will be provided without charge.
c. Proof of purchase from an authorized MITSUBISHI dealer is required when requesting warranty service. Present your sales receipt or other document which establishes proof and date of purchase. THE RETURN OF THE OWNER REGISTRATION
CARD IS NOT A CONDITION OF WARRANTY COVERAGE. However, please return the Owner Registration Card so that we can contact you should a question of safety arise which could affect you.
2. THIS LIMITED WARRANTY DOES NOT COVER:
a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).
b. Cosmetic damage or any other damage where such damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other than an authorized MITSUBISHI service center; physical abuse to or misuse of the product (or any product damaged by excessive physical or electrical stress); any products that have had a serial number or any part thereof altered, defaced or removed; product use in any manner contrary to the Owner’s Guide; freight damage; or any damage caused by acts of God or other factors beyond the reasonable control of MDEA, such as power surge damage caused by electrical system or damages caused by use of third party mounting brackets or stands. This limited warranty also excludes service calls where no defect in the product covered under this warranty is found, service calls related to unsatisfactory audio or visual reception or signal unless caused by a defect in the product that is covered under this limited warranty, all costs, expenses or any other damages arising from product installation, removal from or re-installation into custom installations or on
For assistance call 1(800) 332-2119
Warranty
39
wall mountings, or set-ups, any adjustments of user controls (including contrast, brightness, color, tint, fine tuning, sharpness), other adjustment necessary to prepare the unit for display or use, connection with any external audio receiver, antenna, cable or satellite systems, or service of products purchased or serviced outside the U.S.A. Please consult the operating instructions contained in the Owner’s Guide furnished with the product for information regarding user controls.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION, MIGHT
ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY LIMITED TO A TERM OF
ONE YEAR.
4. UNDER NO CIRCUMSTANCES SHALL MDEA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY INCI-
DENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF
CONTRACT, OR OTHERWISE.
5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental, special, or consequential damages, so the above limitations or exclusions may not apply to you.
6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
7. In the event of any dispute under this limited warranty, jurisdiction and venue for resolving that dispute will be in the state where the television was purchased and the laws of such state will govern. In no event shall Mitsubishi have any liability, including with out limitation, for general, consequential, incidental, or special damages for loss, destruction, damage or corruption of recorded data, media or software resulting from use of this television, or cost of recovery of lost data, media or software therefore.
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road
Irvine, CA 92618-1904
Network Service Disclaimer
Third party content and services, including without limitation home entertainment services by VUDU, Inc., are provided in accordance with whatever terms and conditions are established by the third party providers and agreed to by you.
Mitsubishi Digital Electronics America (“MDEA”) has no control over any such third parties or any agreement you reach with them. MDEA has no control over the networks or transmission facilities by which content and services are provided by third parties. Your connection to the internet may vary in availability and quality. Customer service questions are to be directed to the third-party provider, not MDEA.
MDEA DOES NOT WARRANT CONTENT OR SERVICES PROVIDED BY ANY THIRD PARTY, EITHER EXPRESSLY OR
IMPLIEDLY, FOR ANY PURPOSE. MDEA DOES NOT WARRANT THAT ANY THIRD PARTY SERVICE WILL REMAIN
AVAILABLE FOR ANY PERIOD OF TIME OR THAT IT WILL BE SATISFACTORY, UNINTERRUPTED OR ERROR FREE.
MDEA EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO, WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO ANY THIRD PARTY CONTENT
AND SERVICES.
MDEA WILL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE, WHETHER IN CONTRACT OR TORT OR OTHER
LEGAL THEORY, FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, ATTORNEY
FEES, EXPENSES, OR ANY OTHER DAMAGES ARISING OUT OF, OR IN CONNECTION WITH, YOUR USE OF ANY
CONTENT OR SERVICE THAT IS PROVIDED TO YOU BY ANY THIRD PARTY, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES.
For assistance call 1(800) 332-2119
Website:
www.mitsubishi-tv.com
E-mail:
Call Consumer Relations for operational or connection assistance at
800-332-2119
To order replacement or additional remote controls or NetCommand IR emitters,
Visit our website www.mitsuparts.com
or call
800-553-7278
SYSTEM RESET
If the TV does not respond to the remote control, control-panel buttons, or will not power on/off, press and hold the POWER button on the control panel for ten seconds.
The TV will turn off. Power on the TV and the green
LED will flash quickly for about one minute. Recent settings changes may be lost.
VLP43/+/++
© 2010 Mitsubishi Digital Electronics America, Inc.
For Your Records
Record the model number, serial number, and purchase date of your TV. The model and serial numbers are on the back of the TV. Refer to this page when requesting assistance with the TV.
MODEL NUMBER
SERIAL NUMBER
PURCHASE DATE
RETAILER NAME
LOCATION
853B710B60
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement