Motorola Symbol DS6878 Specifications

Symbol CR0078-P Cradles
Quick Reference Guide
2
Symbol CR0078-P Cradles
© 2010 MOTOROLA, INC. All rights reserved.
Motorola reserves the right to make changes to any product to improve reliability,
function, or design.
Motorola does not assume any product liability arising out of, or in connection
with, the application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise
under any patent right or patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which Motorola products
might be used. An implied license exists only for equipment, circuits, and
subsystems contained in Motorola products.
This Motorola product may include Motorola Software, Commercial Third Party
Software, and Publicly Available Software. Refer to the Product Reference Guide
for complete copyright, conditions and disclaimer information.
Warranty
For the complete Motorola hardware product warranty statement, go to:
http://www.motorola.com/enterprisemobility/warranty.
Quick Reference Guide
3
Introduction
The cordless scanner cradle model CR0078 (part CR0078-P) acts as a stand,
charger and host communication interface for DS6878 cordless scanners. The
CR0078-P cradle receives data from the scanner via a Bluetooth radio, and sends
that data to the host through an attached cable. The cradle also charges the
scanner’s internal battery pack when the scanner is inserted. The cradle must be
powered by an external power supply.
This document provides basic instructions on setting up and using the cradle.
Configurations
This guide includes information on the following configurations:
•
CR0078-PC1F09BWR - Cordless scanner cradle; hands-free presentation,
charging, Bluetooth, FIPS, healthcare white
•
CR0078-PC1F007WR - Cordless scanner cradle; hands-free presentation,
charging, Bluetooth, FIPS, twighlight black
Accessories
The following equipment is needed:
•
•
Power Supply (see Power Supply on page 11 for detailed requirements)
Line Cord
•
Host Cable
IMPORTANT For USB interface, only use a cable with a shielded modular
plug (for example: CBA-U21-S07ZAR or CBA-U29-S15ZAR)
Save the shipping container for storing or shipping. Inspect all equipment for
damage. If anything is damaged or missing, call an authorized Customer Support
Representative immediately.
4
Symbol CR0078-P Cradles
Cradle Parts
Front
Latch
Charging/
Communication
Contacts
Pager Button
LED
Back
Power Cable Groove
Rubber Foot
Host Cable Groove
Power Cable Groove
Cable Support Hook
Host Port
Host Cable Groove
Rubber Foot
Cable Support Hook
Power Port
Mounting Hole
Mounting Hole
Rubber Foot
Rubber Foot
Quick Reference Guide
5
Cradle Connections
Important: Connect the interface cable and power supply in the following order to
ensure proper operation of the scanner and cradle:
1. Insert the interface cable into the cradle’s host port.
2. Connect the other end of the interface cable to the host.
3. Connect the power supply to the cradle’s power port.
4. Connect the appropriate cable to the power supply and AC power source.
5. Thread the interface cable over the cable support hook (see Cradle Parts on
page 4) and run the host and power cables into their respective cable grooves.
6. If necessary, scan the appropriate host bar code (for non-autodetected
interfaces). Refer to the Symbol DS6878 Product Reference Guide, p/n
72-131700-xx.
Power Port
Power
Connect to
appropriate host
Alternate
Host Groove
Alternate
Power Groove
Power Port
Host Port
Host Port
Changing the Host Interface
To connect to a different host, or to the same host through a different cable:
1. Unplug the power supply from the cradle.
2. Unplug the interface cable from the host.
3. Connect the interface cable to the new host, or the new interface cable to the
existing host.
4. Reconnect the power supply.
5. If necessary, scan the appropriate host bar code with a paired scanner (for
non-autodetected interfaces). Refer to the Symbol DS6878 Product Reference
Guide, p/n 72-131700-xx.
If the cradle does not recognize the host, disconnect the power supply,
then reconnect after connecting the host cable.
6
Symbol CR0078-P Cradles
Inserting the Scanner in the Cradle
To insert the scanner in the cradle:
1. Insert the scanner by placing the bottom of the scanner, at a slight forward
angle, into the CR0078-P cradle.
2. Push the handle back and down until it clicks, engaging the contacts of the
scanner and cradle.
1
2
Click
Removing the Scanner from the Cradle
To remove the scanner from the cradle:
1. Remove the scanner by pushing the scanner slightly forward and up out of the
CR0078-P cradle.
2
1
Click
Quick Reference Guide
7
Sending Data to the Host Computer
The cradle receives data from the scanner via a wireless radio connection and
transmits it to the host computer via the host cable. The scanner and cradle must
be paired for successful wireless communication.
Pairing
Pairing registers a scanner to the cradle so that the scanner and cradle can
exchange information. The CR0078-P Series operates in the following modes:
scanner-to-cradle, point-to-point, multi scanner-to-cradle and multipoint-to-point.
In scanner-to-cradle mode, the scanner is paired to the cradle by inserting the
scanner into the cradle. In multi scanner-to-cradle mode, up to seven scanners
can be paired to one cradle. A multipoint bar code must be scanned to activate
this feature.
When the scanner is inserted in the cradle, a low-high beep sequence indicates
successful pairing and connection to the remote device. A long low, long high
beep sequence indicates unsuccessful pairing. Refer to the Symbol DS6878
Product Reference Guide, p/n 72-131700-xx for more information.
NOTE If the battery is off when the scanner is inserted in the cradle, a
high-low-high-low beep sequence indicates power up.
Lost Connection to Host
If scanned data does not transmit to the cradle’s host, ensure that all cables are
firmly inserted and the power supply is connected to an appropriate AC outlet. If
scanned data still does not transmit to the host, reestablish a connection with the
host:
1. Disconnect the power supply from the cradle.
2. Disconnect the host interface cable from the cradle.
3. Wait three seconds.
4. Reconnect the host interface cable to the cradle.
5. Reconnect the power supply to the cradle, if required.
6. Reestablish pairing with the cradle by inserting the scanner into the cradle.
8
Symbol CR0078-P Cradles
Charging the Scanner Battery in the Cradle
To charge the scanner battery, place the scanner in the cradle (see Inserting the
Scanner in the Cradle on page 6). The battery begins charging when the scanner
LED indicator turns solid green. A complete charge of a fully discharged battery
can take up to three hours.
LED Charging Indications
When powered up, the cradle LED is always green. Refer to the Symbol DS6878
Product Reference Guide, p/n 72-131700-xx for scanner LED indications.
Page Button
The page button is a sensor that, when touched causes paired scanners to emit a
beeping sequence. The default is Disable Page Button.
1. Place your finger over the button and hold the button down for approximately 1
second.
2. The cradle LED will turn blue and any paired scanners will beep five times. If
multiple scanners are paired to the cradle, all the scanners will beep five times.
3. Repeat as necessary.
NOTE Scanners out of radio range will not beep when paged. Refer to
the Symbol DS6878 Product Reference Guide, p/n 72-131700-xx
for more information.
Scan one of the following bar codes to enable or disable this feature.
*Disable Page Button
Enable Page Button
Quick Reference Guide
Troubleshooting
If the cradle does not work after following the previous procedures:
•
•
•
Check the system power.
Check for loose cable connections.
Check that the scanner is inserted properly in the cradle.
• Check that the host settings are correct and the cradle is connected to the
appropriate port on the host.
CAUTION
Do not pour, spray, or spill any liquid on the cradle. Refer
to the Symbol DS6878 Product Reference Guide, p/n
72-131700-xx for maintenance guidelines and list of
approved cleansers.
Related Documentation
•
Symbol DS6878 Product Reference Guide, p/n 72-131700-xx
•
Symbol DS6878 Quick Start Guide, p/n 72-132659-xx
These documents are available at the following web site:
http://www.motorola.com/enterprisemobility/manuals.
9
10
Symbol CR0078-P Cradles
Regulatory Information
This device is approved under the Symbol Technologies brand; Symbol Technologies, Inc., is the
Enterprise Mobility Solutions of Motorola, Inc. (“Motorola”).
This guide applies to model number CR0078.
All Motorola/Symbol devices are designed to be compliant with rules and regulations in locations they
are sold and will be labeled as required.
Local language translations are available at the following web site:
http://www.motorola.com/enterprisemobility/manuals.
Any changes or modifications to Motorola/Symbol Technologies equipment, not expressly approved
by Symbol Technologies, could void the user's authority to operate the equipment.
Only use Motorola/Symbol approved and UL listed accessories, battery packs and battery chargers.
Bluetooth® Wireless Technology
This is an approved Bluetooth® product. For more information or to view end product listing, visit the
following web site: https://www.bluetooth.org/tpg/listings.cfm.
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the
recommendations below. Consult with your local Health & Safety Manager to ensure that you are
adhering to your company's safety programs to prevent employee injury.
•Reduce or eliminate repetitive motion
•Maintain a natural position
•Reduce or eliminate excessive force
•Keep objects that are used frequently within easy reach
•Perform tasks at correct heights
•Reduce or eliminate vibration
•Reduce or eliminate direct pressure
•Provide adjustable workstations
•Provide adequate clearance
•Provide a suitable working environment
•Improve work procedures.
Warnings for Use of Wireless Devices
Please observe all warning notices with regard to the usage of wireless devices.
Potentially Hazardous Atmospheres - Vehicles Use
You are reminded of the need to observe restrictions on the use of radio devices in fuel depots,
chemical plants, etc. and areas where the air contains chemicals or particles (such as grain, dust, or
metal powders) and any other area where you would normally be advised to turn off your vehicle
engine.
Potentially Hazardous Atmospheres - Fixed Installations
You are reminded of the need to observe restrictions on the use of radio devices in fuel depots,
chemical plants, etc. and areas where the air contains chemicals or particles (such as grain, dust, or
metal powders).
Safety in Aircraft
Switch off your wireless device whenever you are instructed to do so by airport or airline staff. If your
device offers a “flight mode” or similar feature, consult airline staff as to its use in flight.
Quick Reference Guide
11
Safety in Hospitals
Wireless devices transmit radio frequency energy and may affect medical electrical equipment.
Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics or
healthcare facilities. These request are designed to prevent possible interference with sensitive
medical equipment.
Pacemakers
Pacemaker manufacturers recommend that minimum of 15cm (6 inches) be maintained between a
handheld wireless device and a pacemaker to avoid potential interference with the pacemaker. These
recommendations are consistent with independent research and recommendations by Wireless
Technology Research.
Persons with Pacemakers:
• Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned
ON.
• Should not carry the device in a breast pocket.
• Should use the ear furthest from the pacemaker to minimize the potential for interference.
• If you have any reason to suspect that interference is taking place, turn OFF your device.
Other Medical Devices
Please consult your physician or the manufacturer of the medical device, to determine if the
operation of your wireless product may interfere with the medical device.
FCC RF Exposure Guidelines
Safety Information
Reducing RF Exposure - Use Properly
Only operate the device in accordance with the instructions supplied.
International
The device complies with Internationally recognized standards covering human exposure to
electromagnetic fields from radio devices. For information on “International” human exposure to
electromagnetic fields refer to the Motorola/Symbol Declaration of Conformity (DoC) at the following
web site: http://www.motorola.com/doc.
Handheld Devices
To comply with FCC RF and EU RF exposure requirements, this device must be operated in the hand
with a minimum separation distance of 20cm or more from a person’s body. Other operating
configurations should be avoided.
Power Supply
Use ONLY a LISTED Motorola, Type no. 50-14000 (12 Vdc/650 mA minimum), or PWRS-14000 (12
Vdc/650 mA minimum), Direct Plug-In Power Supply, marked Class 2 or LPS (IEC60950-1, SELV).
Use of an alternative power supply will invalidate any approval given to this device and may be
dangerous.
12
Symbol CR0078-P Cradles
Batteries
Taiwan - Recycling
EPA (Environmental Protection Administration) requires dry battery producing or importing firms in
accordance with Article 15 of the Waste Disposal Act are required to indicate the recycling marks on
the batteries used in sales, giveaway or promotion. Contact a qualified Taiwanese recycler for proper
battery disposal.
To charge the mobile device battery, the battery and charger temperatures must be between +32 °F
and +104 °F (0 °C and +40 °C).
Radio Frequency Interference Requirements-FCC
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Radio Frequency Interference Requirements-Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numèrique de la classe B est conforme à la norme NMB-003 du Canada.
Radio Transmitters
This device complies with RSS 210 of Industry & Science Canada. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Label Marking: The Term “IC:” before the radio certification only signifies that Industry Canada
technical specifications were met.
Marking and European Economic Area (EEA)
Bluetooth® Wireless Technology for use through the EEA has the following restrictions:
Quick Reference Guide
•
•
•
13
Maximum radiated transmit power of 100mW EIRP in the frequency range 2.400-2.4835 GHz.
France, outside usage is restricted to 10mW EIRP.
Italy requires a user license for outside usage.
Statement of Compliance
Motorola/Symbol Technologies, Inc., hereby, declares that this device is in compliance with the
essential requirements and other relevant provisions of Directives 1999/5/EC. A Declaration of
Conformities may be obtained from the following web site: http://www.motorola.com/doc.
Country Approval
Regulatory markings, subject to certification, are applied to the device signifying the radio(s) are
approved for use in the following countries: United States, Canada, Australia, China, S. Korea, Japan
& Europe.
Please refer to the Symbol Declaration of Conformity (DoC) for details of other country markings.
This is available at the following web site: http://www.motorola.com/doc.
NOTE For 2.4GHz Products, Europe includes: Austria, Belgium, Bulgaria, Czech
Republic, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg,
Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic,
Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
Operation of the device without regulatory approval is illegal.
Japan (VCCI) - Voluntary Control Council for Interference
Class B ITE
ሶቑ孔函ቒᇬ㍔⫀⑵䚕孔函䷘榊㽱椫⹂呹⃊尞Ⓟ◣巿↩᧤ᨒ᧿᧿ᨅ᧥ቑ⪉䄥቎⪉ቈሲኌ዆ኖB
⫀㔏嫢孔函ቊሼᇭሶቑ孔函ቒᇬ⹅ㄼ䜿⬒ቊ∎䞷ሼቮሶቋት䥽䤓ቋሺ቉ሧቡሼሯᇬሶቑ孔函ሯ
዆ንኇቧኣዉኰንዄዐ♦≰㳮቎扠㘴ሺ቉∎䞷ሸቯቮቋᇬ♦≰椫⹂ትㆤሰ怆ሶሼሶቋሯሥቭቡ
ሼᇭ
♥㔀崻㢝㦇቎㈢ቆ቉㷲ሺሧ♥ቭ㔀ሧትሺ቉ₚሸሧᇭ
This is a Class B product based on the standard of the Voluntary Control Council for Interference
from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a
domestic environment, it may cause radio interference. Install and use the equipment according to
the instruction manual.
Korean Warning Statement for Class B ITE
기종별
B 급 기기
( 가정용 방송통신기기 )
사용자안내문
이 기기는 가정용 (B 급 ) 으로 전자파적합등록을
한 기기로서 주로 가정에서 사용하는 것을 목적
으로 하며 , 모든 지역에서 사용할 수 있습니다 .
Other Countries
Brasil: Declarações Regulamentares para CR0078-P.
Nota: A marca de certificação se aplica ao Transceptor, modelo CR0078. Este equipamento opera
em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de
estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.
Para maiores informações sobre ANATEL consulte o site: www.anatel.gov.br
CHILE: Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de
telecomunicaciones, relativa a radiaciones electromagnéticas.
Mexico: Restrict Frequency Range to: 2.450 - 2.4835 GHz.
14
Symbol CR0078-P Cradles
Korean
鲮뼩 ꓩ꫕꫙ꟹ鱉 끩끞 닆 놹볁뿱겕 閵鱚ꫦ넩 넽넁
鲮뼩 ꓩ꫕꫙ꟹ 鱉놹볁뿱 겕 閵鱚ꫦ넩 넽냱ꕵꈑ 넭ꐺ껽놹隱 隵ꇝ鷑 ꫑ꟹ걙鱉 뼕 ꯍ 꽻걪鱽鲙
Taiwan
Waste Electrical and Electronic Equipment (WEEE)
Bulgarish: За клиенти от ЕС: След края на полезния им живот всички продукти трябва да
се връщат на Motorola за рециклиране. За информация относно връщането на продукти,
моля отидете на адрес:
http://www.motorola.com/recycling/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich životnosti vrátit
spoleènosti Motorola k recyklaci. Informace o zpùsobu vrácení produktu najdete na webové
stránce: http://www.motorola.com/recycling/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Motorola til recirkulering, når de er
udtjent. Læs oplysningerne om returnering af produkter på:
http://www.motorola.com/recycling/weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer
zum Recycling an Motorola zurückgesandt werden. Informationen zur Rücksendung von
Produkten finden Sie unter http://www.motorola.com/recycling/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει
να επιστρέφονται στην Motorola για ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με
την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση
http://www.motorola.com/recycling/weee στο Διαδίκτυο.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise
eesmärgil Motorola'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun
aadressi: http://www.motorola.com/recycling/weee.
English: For EU Customers: All products at the end of their life must be returned to Motorola
for recycling. For information on how to return product, please go to:
http://www.motorola.com/recycling/weee.
Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a
Motorola al final de su ciclo de vida para que sean reciclados. Si desea más información sobre
cómo devolver un producto, visite: http://www.motorola.com/recycling/weee.
Français: Clients de l'Union Européenne : Tous les produits en fin de cycle de vie doivent être
retournés à Motorola pour recyclage. Pour de plus amples informations sur le retour de
produits, consultez : http://www.motorola.com/recycle/weee.
Quick Reference Guide
15
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita
devono essere restituiti a Motorola al fine di consentirne il riciclaggio. Per informazioni sulle
modalità di restituzione, visitare il seguente sito Web:
http://www.motorola.com/recycling/weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ
Motorola otrreizējai pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu Motorola,
lūdzu, skatiet: http://www.motorola.com/recycling/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti
utilizuoti į kompaniją „Motorola“. Daugiau informacijos, kaip grąžinti gaminį, rasite:
http://www.motorola.com/recycling/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Motorola vállalathoz kell
eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos
tudnivalókért látogasson el a
http://www.motorola.com/recycling/weee weboldalra.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu
jiġu rritornati għand Motorola għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna
l-prodott, jekk jogħġbok żur: http://www.motorola.com/recycling/weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur
naar Motorola te worden teruggezonden voor recycling. Raadpleeg
http://www.motorola.com/recycling/weee voor meer informatie over het terugzenden van
producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y zwróciæ
do firmy Motorola w celu ich utylizacji. Informacje na temat zwrotu produktów znajduj¹ siê na
stronie internetowej http://www.motorola.com/recycling/weee.
Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à
Motorola para reciclagem. Para obter informações sobre como devolver o produto, visite:
http://www.motorola.com/recycling/weee.
Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare,
trebuie returnate la Motorola pentru reciclare. Pentru informaţii despre returnarea produsului,
accesaţi: http://www.motorola.com/recycling/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju
Motorola za reciklažo. Za informacije o vračilu izdelka obiščite:
http://www.motorola.com/recycling/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich
životnosti vrátené spoločnosti Motorola na recykláciu. Bližšie informácie o vrátení výrobkov
nájdete na: http://www.motorola.com/recycling/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi
Motorola-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on
osoitteessa http://www.motorola.com/recycling/weee.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till
Motorola för återvinning. Information om hur du returnerar produkten finns på
http://www.motorola.com/recycling/weee.
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Motorola'ya
iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu adresi ziyaret edin:
http://www.motorola.com/recycling/weee.
Service Information
If you have a problem with your equipment, contact Motorola Enterprise
Mobility support for your region. For contact information, go to:
http://www.motorola.com/enterprisemobility/support.
When contacting Enterprise Mobility support, please have the following
information available:
- Serial number of the unit
- Model number or product name
- Software type and version number
Motorola responds to calls by e-mail, telephone or fax within the time limits set
forth in service agreements. If your problem cannot be solved by Motorola
Enterprise Mobility Support, you may need to return your equipment for
servicing and will be given specific directions. Motorola is not responsible for
any damages incurred during shipment if the approved shipping container is
not used. Shipping the units improperly can possibly void the warranty.
If you purchased your Enterprise Mobility business product from a Motorola
business partner, please contact that business partner for support.
For the latest version of this guide, go to:
http://www.motorola.com/enterprisemobility/manuals.
Motorola, Inc.
One Motorola Plaza
Holtsville, New York 11742, USA
1-800-927-9626
http://www.motorola.com/enterprisemobility
MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in
the U.S. Patent and Trademark Office. All other product or service names are the
property of their registered owners. © Motorola, Inc. 2010
72-138860-01 Revision A - June 2010